WIRE CONNECTOR
(3 PCS)
CROSSBAR
IPPLE
CANOPY I
T CREW
= COLLAR NUT
) |
Ц CREW
QUICK LINK | COLLAR LOOP
(|
|
(
[)-— сн
|
|
|
|| QUICK LINK
CHAIN LOOP vu
A =
(TN
|
||
||
||
GLASS SHADE 5 т
ASSEMBLY | | Lu
L |
- GLASS
SHADE
Ÿ
woe: 9183 1CLR
ASSEMBLY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
READ INSTRUCTIONS ALL THE WAY THROUGH PRIOR TO
ASSEMBLY.
THIS FIXTURE SHOULD TAKE APPROXIMATELY 5 MINUTES TO
ASSEMBLE.
MAKE SURE ALL PARTS ARE FIRMLY TIGHTENED.
TOOLS: YOU WILL NEED THE FOLLOWING TOOLS OR
EQUIPMENT: LADDER, SCREWDRIVER, ADJUSTABLE WRENCH,
WIRE CUTTERS AND PLIERS.
UNPACK THE FIXTURE
YOU SHOULD HAVE RECEIVED THE FOLLOWING PARTS IN THE
PACKAGE: CANOPY, CHAIN, (2) QUICK LINKS, CHAIN LOOP
AND GLASS SHADE ASSEMBLY. TO PROTECT THE FINISH,
PLACE ALL PARTS ON A SOFT SURFACE.
MOUNTING HARDWARE PACKAGE:
SCREW COLLAR LOOP, SCREW COLLAR NUT, NUT, NIPPLE, (2)
8-32 X 1-1/4" SCREWS, CROSSBAR, GREEN GROUND
SCREW AND (3) WIRE CONNECTORS.
FIXTURE ASSEMBLY
1. SCREW CHAIN LOOP TO TOP OF GLASS SHADE ASSEMBLY.
2. DETERMINE THE LENGTH OF CHAIN REQUIRED TO HANG
THE LANTERN AT THE DESIRE HEIGHT, REMOVE OR ADD CHAIN
AS DESIRED. ATTACH THE QUICK LINK TO ONE END LINK OF
CHAIN AND ATTACH THE QUICK LINK TO THE CHAIN LOOP.
REMOVE OR ADD CHAIN AS DESIRED AT THIS TIME. THREAD
LANTERN WIRE AND GROUND WIRE UP THROUGH EVERY
OTHER LINK OF CHAIN.
**STOP** COMPLETE INSTALLATION
INSTRUCTIONS ON NEXT PAGE BEFORE
CONTINUING TO FINAL ASSEMBLY.
FINAL ASSEMBLY
1. INSTALL A 60 WATT MAX. MEDIUM BASE TYPE "A" BULB
(NOT INCLUDED) INTO SOCKET.
2. RESTORE POWER, YOUR NEW FIXTURE IS NOW READY FOR
USE.
03/2013 91831CLR INSTRUCTIONS
SUPPLY GROUND WIRE = - | OUTLET BOX
< WHITE
BLACK SUPPLY WIRE - SUPPLY WIRE
CEILING A a WIRE CONNECTORS
BLACK OR SMOOTH — — | | (3 PCS)
FIXTURE WIRE
WHITE OR RIBBED
8—32 SCREWS, FIXTURE WIRE
SUPPLIED WITH BOX
All
ROSSBAR
NIPPLE: -
CANOPY
IXTURE GROUND WIRE
REEN GROUND SCREW
SCREW COLLAR NUT:
SCREW COLLAR LOOP
CHAIN
INSTALLATION INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
CAUTION
TO AVOID POSSIBLE ELECTRIC SHOCK, MAKE SURE THE ELECTRICITY IS SHUT OFF AT THE MAIN PANEL. IF YOU
ARE REPLACING AN EXISTING FIXTURE, FIRSTLY, TURN THE FIXTURE OFF. NEXT, TURN THE WALL SWITCH OFF.
FINALLY, GO TO THE MAIN FUSE OR BREAKER BOX IN YOUR HOME. TURN THE FUSE OR BREAKER TO THE OFF
POSITION. SOME TYPES OF FUSES MUST BE UNSCREWED TO SHUT OFF THE POWER.
* ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRIC CODES. IF YOU ARE NOT
FAMILIAR WITH WIRING, YOU SHOULD USE A QUALIFIED ELECTRICIAN.
** THIS FIXTURE IS INTENDED TO BE MOUNTED TO A UL LISTED OUTLET BOX CAPABLE OF SUPPORTING THE
FIXTURE.
1. ATTACH THE CROSS BAR TO THE CEILING OUTLET BOX USING THE TWO SCREWS PROVIDED WITH THE
OUTLET BOX. (NOTE: IF THE SCREWS WITH THE OUTLET BOX ARE TOO SHORT, USE THE (2) 8-32 x 1-1/4"
SCREWS PROVIDED IN THE MOUNTING HARDWARE PACKAGE). NEXT, SCREW THE SCREW COLLAR LOOP ONTO
THE NIPPLE AND THEN SCREW THE NIPPLE INTO THE CROSS BAR.
2. SLIDE THE SCREW COLLAR NUT AND THEN THE CANOPY ONTO THE END OF THE CHAIN. THEN FASTEN THE
END LINK OF CHAIN TO THE SCREW COLLAR LOOP.
3. INSERT THE FIXTURE WIRE AND THE GROUND WIRE UP THROUGH THE NIPPLE. CONNECT THE WHITE OR
RIBBED FIXTURE WIRE TO THE WHITE SUPPLY WIRE IN THE OUTLET BOX USING THE TWIST—ON WIRE
CONNECTORS PROVIDED. CONNECT THE BLACK OR SMOOTH FIXTURE WIRE TO THE BLACK SUPPLY WIRE IN THE
SAME MANNER. INSTALL THE FIXTURE GROUND WIRE UNDER THE GREEN GROUND SCREW ON THE CROSSBAR
THEN CONNECT THE FIXTURE GROUND WIRE TO THE SUPPLY GROUND WIRE IN THE OUTLET BOX USING THE
TWIST—ON WIRE CONNECTOR PROVIDED.
4. TUCK THE WIRES CAREFULLY INSIDE THE OUTLET BOX. SPREAD THE ELECTRICAL SPLICES SO THAT THE
BLACK WIRES ARE ON ONE SIDE OF THE OUTLET BOX AND THE WHITE WIRES ARE ON THE OTHER SIDE. NEXT
RAISE THE CANOPY TO THE CEILING AND SECURE IN PLACE BY SCREWING THE SCREW COLLAR NUT ONTO THE
SCREW COLLAR LOOP.
5. SEE PREVIOUS PAGE FOR FINAL ASSEMBLY INSTRUCTIONS.
03/2013 91831CLR INSTALLATION
">