I
WIRELESS MOTION SENSOR LED CEILING LIGHT
“YS OWNER’S MANUAL
BRILLIANT Model # BRRC109
EVOLUTION
MZ,
1
LOCATION OF CONTROLS: >
1. Motion Sensor «Eu
2. Battery Compartment/Mounting Bracket
INSTALLATION:
1. Remove mounting bracket from the light by sliding the bracket towards OPEN (Fig. 2). Lift the bracket off the light.
2. Place the CEILING SIDE of the bracket on the ceiling and use the mounting bracket as a guide to mark the two (2) pilot holes.
3. Drill pilot holes for the plastic anchors. Insert the anchors in the pilot holes.
4, Place the mounting bracket over the anchors. The CEILING SIDE of the bracket should be facing the ceiling. Drive the screws
through the holes in the mounting bracket and into the anchors. Do not over tighten.
5. Attach the light to the mounting bracket. Match up the A and B on the mounting bracket (Fig. 3) with the A and B on the light (Fig. 4).
Slide the light toward CLOSE.
FIG. 2 FIG. 3 FIG. 4
= = a
à fl я
e ©
T LIGHT
SIDE
CEILING
SIDE
T .
OPERATING INSTRUCTIONS:
Motion Sensor:
1. Insert batteries (see back of manual for instructions).
2. Motion will turn the light ON for 30 seconds.
Light will remain ON if motion continues.
Light will turn OFF after 30 seconds if no motion is detected.
Motion sensor only senses motion in darkness.
Light may activate when batteries are inserted. Move light to a dark room,
allow the light to adjust (up to 5 minutes), then test motion sensor.
DEACTIVATING THE LIGHT SENSOR
If there is too much ambient light in the desired location (preventing the light from turning on) the light sensor can be removed.
Removing the light sensor will cause the light to turn on anytime motion is detected, regardless of how much ambient light is in the
area. The batteries will be consumed more quickly. Use needle nose pliers to lift and remove the black plastic piece in the battery
compartment (Fig. 5).
BATTERIES:
INSERTING / REPLACING THE BATTERIES
If the LEDs appear to be dim the batteries need to be replaced.
TO REPLACE THE BATTERIES
1. Slide the light towards OPEN to remove the light from the
mounting bracket (Fig 6).
2. Remove the battery compartment cover by turning it counter clockwise.
Then lift the cover off the light.
. Remove old batteries (if replacing batteries).
. Insert three (3) new C batteries (not included)
. Make sure to follow the battery polarity guide
when installing new batteries (Fig. 7).
6. Replace battery compartment cover by turning it clockwise.
7. Slide the light back on to the mounting bracket.
с > ©
PRODUCT INFORMATION CHART:
Light Output (Lumens) 200
Correlated Color Temperature (CCT) 4000 (Bright White)
Run Time 40 hours
Batteries (not included) Cx3
Number of LEDs 9
LED Beam Angle 120°
Motion Sensor Detection Range 20 Feet
Motion Sensor Detection Angle 120°
Motion Sensor Auto Shut Off 30 Seconds
Dimensions: 5-1/4" wide / 5-1/4" deep / 2" high
BATTERY PRECAUTIONS:
1. Use only the size and type of batteries specified.
2. Always purchase the correct size and grade of battery most suitable for the intended use.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may
cause damage to the device.
4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.
5. Replace all batteries of a set at the same time. Do not mix old and new batteries.
6. Clean the battery contacts and also those of the device prior to battery installation.
7. Do not dispose of batteries in fire.
8. Remove batteries if consumed or if product is to be left unused for an extended period of time.
WEATHER RESISTANT
ONE-YEAR LIMITED WARRANTY:
This product is warranted to the original purchaser that the product will be free from defects in materials and workmanship for a period of
one year from the date of purchase. Additional details are available at www.brilliantevolution.com.
O 2018 London Johnson, Inc. All Rights Reserved.
www.brilliantevolution.com
Made in China
">
