- Computers & electronics
- TVs & monitors
- Flat panel wall mounts
- FORGING MOUNT
- Long Extension TV Mount Corner Wall Mount TV Bracket Full Motion
- Installation manual
FORGING MOUNT Long Extension TV Mount Corner Wall Mount TV Bracket Full Motion TV Ceiling & Wall Mount Installation Manual
Add to my manuals
2 Pages
advertisement
▼
Scroll to page 2
Getting Started LONG ARM TV WALL MOUNT Model HY9389-B Does your TV (including accessories) weigth more than 99 lbs. ( 45 kg )? No — Perfect! Yes — This mount is NOTcompatible. 99 lbs. (45 kg) Stud Finder Awl Screwdriver 7/32 in. ( 5 mm) Wood Drill Bit Electric Drill Hammer 3/8 in. (10 mm) Concrete Drill Bit Hardware Included Pencil Concrete Install Wood Stud Install Tools Needed Tape Measure 1/2 in. (13 mm) Socket Wrench NOTE:Not all parts and hardware included will be used. STEP 1-2 Select TV Screw Length Hand thread screws into the threaded inserts on the back of your TV to determine which screw diameter (M4, M6, or M8 ) to use. If your TV has a flat back, AND you want your TV closer to the wall, use the shorter screws (A). M6 M8 Use the spacers and longer s crews(B) to accommodate: · Round/irregular back TVs · TVs with inset mounting holes · Extra space needed for cables A Arm and Wall Plate ● This product is designed for use in wood stud/concrete walls DO NOT install into drywall 04 x1 ● The wall must be capable of supporting fi ve times the weight of the TV and mount combined Solid concrete or concrete block? ● Do not use this product for any purpose not explicitly specifi ed by manufacturer ● Manufacturer is not responsible for damage or injury caused by incorrect assembly or use Lag Bolts TV Washers TV Screws 02 x2 5/16x2.75” Wall plate cover 05 x1 Standard configurations are shown. For special applications, or if you are uncertain about your hardware selection, you can see online: www.forgingmount.com A 03 x2 Cable Cover x5 M4X15 M4X30 D E x4 Lag Bolt Washers HDMI Cable B x5 M6X15 M6X30 F G x4 M4 /M 5 M6 J x4 K x4 /M 8 x4 Spacers Wrench x4 concrete anchor 06 x5 07 x1 M8X15 C x5 H x4 M8X45 I x4 L5MM L10MM L M x8 x8 N STEP 1-3 Attach the TV plate to the arm assembly take out the wallplate covers from the wall plate CAUTION: Verify adequate thread engagement with the screw/ washer/spacer combination AND TV bracket . B ROUND BACK INSET HOLES CAUTION: Avoid potential personal injuries and property damage! TV Bracket - Too short will not hold the TV. - Too long will damage the TV. FLAT BACK If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact US via: [email protected] Perfect! contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included 01 x1 and undamaged. If any parts are missing or damaged, do not return the damaged item to wallplate template Level your dealer; contact Customer Service. Never use damaged parts! STEP 1-1 Select TV Screw Diameter M4 Drywall with woodstuds? WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer's responsibility to make sure the weight of the TV (with accessories) does not exceed 99 lbs ( 45 kg ). WARNING:This product Please read through these instructions completely to be sure you’re comfortable with this easy install process. Also check your TV owner’s manual to see if there are any special requirements for mounting your TV. What is your wall made of? CABLES Specification Sheet 30”-2.36” Too Short 16.93” 11.2” Correct Too Long 23.6”-5.9” x1 2-1 STEP 2 Wall Plate Install( Wood Stud ) 2-2 2-3 05 3 in. (75mm) 16 in (406 . mm) CAUTION: Avoid potential personal injuries and property damage! ● Drywall covering the wall must not exceed 5/8 in. (16 mm) ● Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal½1x 3½ in. (38 x 89 mm) 2-4 7/32 in. (5.5 mm) 04 CAUTION: Avoid potential personal injury or property damage! All lag bolts A MUST BE firmly tightened to prevent unwanted movement of the wall plate 01 . CAUTION: Ensure the wall plate is securely fastened to the wall before continuing on to the next step. B A Locate your studs. Verify and mark the center of Position the template 04 at your desired height Drill pilot holes using a 7/32 in (5.5mm) diameter drill bit. the studs by finding the stud edges using an awl, and line up the holes with your stud center line. IMPORTANT: Pilot holes must be drilled to a depth a thin nail, or an edge-to-edge stud finder. Level the wall plate and mark the holes. STEP 3 Wall Plate Install( Solid Concrete or Concrete Block ) 3-1 of 3 in.(75 mm).Be sure to drill into the center of the stud. 3-2 3-3 Install wall plate 01 using lag bolt A and washers B .Tighten the lag bolts only until they are pulled firmly a gainst the wall plate 01 3-3 C B Min. 8 in. (203 mm) Min. 8 in. (203 mm) Min. 16 in. (406 mm) UP CAUTION: Avoid potential personal injuries and property damage! ● Minimum solid concrete thickness: 8 in. (203 mm). 04 Min. 16 in. (406 mm) Position template 04 at your desired height. Level, then mark the five hole locations. ● Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm) ● Minimum horizontal space between fasteners: 16 in (406 mm). 01 Drill five pilot holes using a 3/8 in. (10 mm) masonry drill bit. IMPORTANT:Pilot holes must be drilled to a depth of 3 in ( 75 mm ). Never drill into the mortar between blocks. Insert five concrete anchors ( 10x60mm ) to the wall B CAUTION: Be sure the anchors are seated flush with the concrete surface. Install wall plate 01 with five washers B and screws A CAUTION: Improper use could reduce the holding power of screws A DO NOT over-tighten the screws. ● Mount wall plate 01 directly onto the concrete surface. STEP 4 Attach TV Brackets to TV back STEP 6 installation wallplate cover and cable management STEP 5 Attach TV to the arm assembly CAUTION: Avoid potential personal injuries and property damage! DO NOT use a power screwdriver for this step a A Attach TV to the mounting bar STEP 7 Tilt and level adjustment Loosen the nut with a wrench N to adjust the appropriate tilt Angle and tighten the nut Use screwdriver to adjust the 2 screws for TV level Flat Back J K D F H 2 2 b Round Back/Extra Space L M J K E G I Tilt adjusting CAUTION: Avoid potential personal injury or property damage! IMPORTANT : Ensure TV bracket is securely fastened before moving on to the next step. Make sure your locking screws are tightened BEHIND the mounting bar so the TV is securely fastened in place. 05 , Leveling Cable management Made in China.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement