advertisement
V1P Pro
User Manual
The information in this manual is subject to change without notice. www.rexingusa.com 12/2018Rev3
1
©2018 REXING All Rights Reserved
V1P Pro Manual
Safety Information
To prevent injury to yourself or others, or damage to your device, read all safety information before using.
Warning
Failure to comply with safety warnings and regulations can result in serious injury or death.
Rexing Dash Cam is not intended to be touched, modified, or calibrated while operating a vehicle. Rexing is not responsible for any damages resulting from the user's misuse of the camera.
Do not use damaged power cords or plugs, or loose electrical sockets.
Faulty connections can cause electric shock or fire.
Do not touch the car charger with wet hands or disconnect the charger by pulling the cord.
Doing so may result in electrocution.
Do not use a bent or damaged car charger. Doing so may cause electric shock or fire.
Do not use your device while it is charging or touch your device with wet hands. Doing so may cause electric shock.
Do not short-circuit the charger or the device.
Doing so may cause electric shock or fire.
Use only manufacturer-approved chargers, accessories, and supplies.
2
©2018 REXING All Rights Reserved
V1P Pro Manual
● Using generic chargers may shorten the life of your device or cause the device to malfunction. They may also cause fire.
● Use only the manufacturer-approved charger specifically designed for your device. Using an incompatible charger can cause serious personal injury or damage to your device.
● Rexing cannot be responsible for the user’s safety when using accessories or supplies that are not approved by Rexing .
Do not drop the charger or device, or subject them to impact. Handle and dispose of the charger and device with care.
● Never crush or puncture the device.
● Never dispose of the device in a fire.
● Never place the device in or on heating devices, such as microwave ovens, stoves, or radiators. The device may explode if overheated.
Follow all local regulations when disposing of a used device.
● Avoid exposing the device to high external pressure, which can lead to an internal short circuit and overheating.
Protect the device and charger from damage.
● Avoid exposing your device to excessive cold or heat. Extreme temperatures can damage the device and reduce the charging capacity and life of your device.
● Do not allow children or animals to bite or chew the device. Doing so can result in fire or explosion, and small parts can be a choking hazard. If children use the device, make sure they use the device properly.
3
©2018 REXING All Rights Reserved
V1P Pro Manual
● Never use a damaged charger.
Caution
Failure to comply with safety precautions and regulations can result in property damage, serious injury or death.
Do not use your device near other electronic devices.
Most electronic devices use radio frequency signals. Your device may interfere with other nearby electronic devices.
Do not use your device near other devices that emit radio signals, such as sound systems or radio towers.
Radio signals from these may cause your device to malfunction.
Do not expose the device to heavy smoke or fumes.
Doing so may damage the outside of the device or cause it to malfunction.
If you notice strange smells or sounds coming from your device, or if you see smoke or liquid leaking from the device, stop using the device immediately and take it to a Rexing Service Center.
Failure to do so may result in fire or explosion.
For your own safety, do not operate the controls of this product while driving.
The window mount is needed when using the recorder in a car. Make sure that you place the device in a location where it won’t obstruct the driver’s view.
Always keep the camera lens clean, and ensure that the lens is not blocked by any object or placed near any reflective material.
If the car’s windshield is tinted with a dark coating, recording quality may be affected.
4
©2018 REXING All Rights Reserved
V1P Pro Manual
Do not store your device in excessively hot, cold, damp or dry locations.
Doing so may cause the screen to malfunction or result in damage to the device.
If your device becomes overheated, allow it to cool down before use.
Prolonged exposure of skin to an overheated device may cause lowtemperature burn symptoms, such as red spots or areas of darker pigmentation.
Install mobile devices and equipment with caution.
● Ensure that any mobile devices or related equipment installed in your vehicle are securely mounted.
● Avoid placing your device and accessories in or near an airbag deployment area. Improperly installed wired equipment can cause serious injury in a situation where airbags inflate rapidly.
Do not drop your device or subject your device to impact. If the device is bent, deformed or damaged, malfunction may occur.
Your device may wear out over time.
Some parts and repairs are covered by the warranty within the validity period, but damage or deterioration related to the use of unapproved accessories is not.
Do not attempt to disassemble, repair, or modify your device.
● Any changes or modifications to your device can void your manufacturer’s warrant y.
Clean your device and charger by wiping with a towel or eraser.
Do not use chemicals or detergents. Doing so can discolor or corrode the outside of the device, and may result in electric shock or fire.
5
©2018 REXING All Rights Reserved
V1P Pro Manual
Do not distribute copyright-protected material. Doing so without the permission of the content owners may violate copyright laws. The manufacturer is not responsible or liable for any legal issues that result from the user’s illegal use of copyrighted material.
Correct Disposal of This Product
(Applicable in countries with separate waste collection systems)
Waste Electrical & Electronic Equipment
This symbol, found on the device, accessories or accompanying literature, indicates that the product and its electronic accessories (e.g. charger, headset,
USB cable) should not be disposed of with other household waste.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for information on where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
6
©2018 REXING All Rights Reserved
V1P Pro Manual
Disclaimer
Some content and services accessible through this device belong to third parties and are protected by copyright, patent, trademark and/or other intellectual property laws. Such content and services are provided solely for your personal non-commercial use.
You may not use any content or services in a manner that has not been authorized by the content owner or service provider. Without limiting the foregoing, unless expressly authorized by the applicable content owner or service provider, you may not modify, copy, republish, upload, post, transmit, translate, sell, create derivative works, exploit, or distribute in any manner or medium any content or services displayed through this device.
“THIRD PARTY CONTENT AND SERVICES ARE PROVIDED “AS IS.”
REXING DOES NOT WARRANT CONTENT OR SERVICES SO PROVIDED,
EITHER EXPRESSLY OR IMPLIEDLY, FOR ANY PURPOSE. REXING
EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING BUT
NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE. REXING DOES NOT GUARANTEE THE
ACCURACY, VALIDITY, TIMELINESS, LEGALITY, OR COMPLETENESS OF
ANY CONTENT OR SERVICE MADE AVAILABLE THROUGH THIS DEVICE
AND UNDER NO CIRCUMSTANCES, INCLUDING NEGLIGENCE, SHALL
REXING BE LIABLE, WHETHER IN CONTRACT OR TORT, FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES, ATTORNEY FEES, EXPENSES, OR ANY OTHER DAMAGES
ARISING OUT OF, OR IN CONNECTION WITH, ANY INFORMATION
CONTAINED IN, OR AS A RESULT OF THE USE OF ANY CONTENT OR
SERVICE BY YOU OR ANY THIRD PARTY, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.”
7
©2018 REXING All Rights Reserved
V1P Pro Manual
Third party services may be terminated or interrupted at any time, and Rexing makes no representation or warranty that any content or service will remain available for any period of time. Content and services are transmitted by third parties by means of networks and transmission facilities over which Rexing has no control. Without limiting the generality of this disclaimer, Rexing expressly disclaims any responsibility or liability for any interruption or suspension of any content or service made available through this device.
Rexing is neither responsible nor liable for customer service related to the content and services. Any question or request for service relating to the content or services should be made directly to the respective content and service providers.
8
©2018 REXING All Rights Reserved
V1P Pro Manual
About This Manual
This device provides high-quality digital recording using Rexing ’s high standards of design, construction and technological expertise. This user manual describes the device’s functions and features in detail.
Please read this manual before using the device to ensure safe and proper use. Note that all descriptions include d here are based on the device’s default settings.
● Images and screenshots may differ in appearance from the actual product. Content may differ from the final product or from software provided by service providers and is subject to change without prior notice.
● For the latest version of this manual, refer to the Rexing website at www.rexingusa.com.
● Available features and additional services may vary by device and software.
● Applications and their functions may vary by country, region, or hardware specifications.
● Rexing is not liable for performance issues caused by applications from any provider other than Rexing .
● Rexing is not liable for performance issues or incompatibilities caused by failure to install the device as stated in this manual.
Attempting to customize the installation may cause the device or applications to work improperly, which may result in device malfunctions and data corruption or loss. These actions are violations of your Rexing agreement and will void your warranty.
● Default applications that come with the device are subject to updates and possible discontinuation of support without prior notice. If you have questions about an application provided with the device, contact an authorized Rexing Service Center.
9
©2018 REXING All Rights Reserved
V1P Pro Manual
Table of Contents
Correct Disposal of This Product ........................................................ 6
Device Layout ................................................................................... 16
Powering the Camera ....................................................................... 23
Inserting the Memory Card ............................................................... 24
Removing the Memory Card ............................................................. 25
Formatting the Memory Card ............................................................ 26
10
©2018 REXING All Rights Reserved
V1P Pro Manual
Turning the Device On and Off ......................................................... 27
Basic Operation ................................................................................ 28
Wi-Fi Connect ................................................................................... 29
Loop Recording ................................................................................. 31
WDR (Wide Dynamic Range) ........................................................... 31
Record Audio .................................................................................... 32
Gravity Sensing ................................................................................. 32
Plate Number .................................................................................... 33
Auto Power Off .................................................................................. 34
Beep Sound ........................................ Error! Bookmark not defined.
11
©2018 REXING All Rights Reserved
V1P Pro Manual
Screen Saver .................................................................................... 35
Daylight Saving ................................................................................. 35
Update Time of GPS ......................................................................... 36
Capture Mode ................................................................................... 37
White Balance ................................................................................... 38
Quick Review .................................................................................... 39
12
©2018 REXING All Rights Reserved
V1P Pro Manual
Camera Playback Mode .................................................................... 40
Computer Playback ........................................................................... 41
GPS Playback ................................................................................... 42
Updating Firmware ............................................................................ 44
Common Solutions ............................................................................ 45
13
©2018 REXING All Rights Reserved
V1P Pro Manual
Product Specifications
Image Sensor
Lens
Aperture
CPU Class
Display
Audio I/O
Memory Support
Front - OV4689, Rear - IMX323
Fixed-focus with full-glass elements f1.8
Novatek
2.4 inch, 4:3 TFT LCD
Internal high-sensitivity mic and speaker
Class 10 or higher Micro SD card (up to 256GB)
Gravity Sensor
White Balance
Exposure
Battery Type
Video Format
Low / Medium / High / Off
Auto
Auto ISO
Supercapacitor
Video Resolution – Single h.264 (.MOV)
2160p24f, 1440p30f, 1080p60f, 1080p30f,
720p60f, 720p30f
Video Resolution – Dual 1080p30f+1080p30f, 720p30f+720p30f
Language
English, Chinese, French, Spanish, Portuguese,
German, Italian, Russian, Japanese
Loop Recording
Screen Saver
Audio Recording
GPS Logger
1 min / 3 min / Off
1 min / 3 min / Off
On / Off
Built-in
14
©2018 REXING All Rights Reserved
V1P Pro Manual
Package Contents
The following items should be found in the package:
● Rexing V1P Pro Dashboard Camera
● Full HD Rear Camera
● Rear Camera cable (20ft)
● Car power connector (12ft)
● 3M adhesive mount
● USB cable
● User manual
● Thank you card
The items supplied with the device and any available accessories may vary depending on your region. Appearances and specifications are subject to change without prior notice. Availability of accessories is subject to change.
All supplied items are designed for use only with this device and may not be compatible with other devices. Malfunctions resulting from the use of unapproved accessories are not covered by the warranty service.
For more information about available accessories, refer to www.rexingusa.com.
15
©2018 REXING All Rights Reserved
Camera Overview
Device Layout
V1P Pro Manual
1. OK (Confirm) Button
/ Emergency Lock Button
2. Up Navigation Button
/ Record Button
3. Power Button
/ Screen Toggle Button
4. Down Navigation Button
/ Mic Button
5. Menu Button
/ Mode Button
6. Micro SD Card Slot
7. Reset Button
8. USB Charging Port
9. Rear Camera Port
10. GPS Logger Port*
*not used by V1P Pro
16
©2018 REXING All Rights Reserved
V1P Pro Manual
Buttons
Button Function
Press: Toggle display on or off
Hold: Turn the device on or off manually
Menus: Confirm a selection
Video Mode: Manually lock current recording
Photo Mode: Take photo
Playback Mode: Start / stop playback
Press: Enter menu, cycle through menus or exit current menu
Hold: Change mode
Menus: Move selection up
Video Mode: Start / stop recording
Hold (Video or Photo Mode): Enable Wi-Fi mode
Playback Mode: Decrease or reverse playback speed / Cycle left through recordings
Menus: Move selection down
Video Mode: Toggle audio recording
Hold (Video or Photo Mode): Change front / rear camera views
Playback Mode: Increase playback speed / Cycle right through recordings
17
©2018 REXING All Rights Reserved
V1P Pro Manual
RESET
Press and hold for 4 seconds to reset the device in the event that it operates erratically, hangs up, or freezes
Indicator Flashing Red
–
Recording
18
©2018 REXING All Rights Reserved
Status Icons
Icon Meaning
Video resolution
Currently recording (blinking)
Wide Dynamic Range enabled
Connected to power source
Audio recording enabled
Audio recording disabled
Video Recording Mode
19
©2018 REXING All Rights Reserved
V1P Pro Manual
Playback Mode
Photo Mode
Loop Recording
Memory card detected
Exposure
GPS searching for signal (animated)
GPS signal acquired (no animation)
Current recording locked
20
©2018 REXING All Rights Reserved
V1P Pro Manual
Getting Started
Installation
Video guide can be found at video.rexingusa.com.
V1P Pro Manual
1. Attach the front camera to the window mount
Make sure that you mount the front camera in a safe, appropriate location where it won’t obstruct the driver’s view. Clean your windshield before applying the mount. Wait at least 20 minutes after applying the mount to the windshield before attaching the camera.
2. Insert a memory card
You will need to insert a memory card before you can begin recording. Do not insert or remove a memory card while the device is powered on. The V1P
Pro supports Micro SD cards up to 256GB in size.
21
©2018 REXING All Rights Reserved
V1P Pro Manual
3. Mount the rear camera
Mount the rear camera as shown above. Use the provided rear camera cable to connect the rear camera to the front camera .
4. Connect the car charger to the car's 12V DC outlet
Run the cable down from your camera to the 12V cigarette lighter port of your vehicle. Be sure to connect only Rexing -approved chargers designed and supplied specifically for use with your device. Using an incompatible charger can cause serious personal injury or damage to your device.
5. Format the memory card
To ensure your camera records to your micro SD card properly and without error, you must format the card within the camera (See: Page 26).
Note: Do NOT insert or remove a memory card while the device is powered on.
22
©2018 REXING All Rights Reserved
V1P Pro Manual
Powering the Camera
You must always connect the camera to a power source while operating the camera. Connect the camera to your vehicle via the included car charger cable.
Connect the larger end of the car charger cable to your car’s cigarette lighter (12V DC power outlet). Connect the other, mini-USB end to the mini-USB port on the device.
Connecting the charger improperly may cause serious damage to the device. Any damage caused by misuse is not covered by the warranty.
Use only Rexing -approved chargers. Using unapproved chargers or cables can damage the device.
If the device receives an unstable power supply, the screen may not function properly. If the device is not operating properly using a Rexing approved charger, please contact Customer Care ([email protected]).
23
©2018 REXING All Rights Reserved
V1P Pro Manual
Inserting the Memory Card
The V1P Pro accepts Micro SD memory cards (class 10 or higher) with a maximum capacity of 256GB.
Depending on the memory card manufacturer and type, some cards may not be compatible with your device. Using an incompatible card may damage the device or the memory card, or corrupt the data stored on it.
We highly recommend using Micro SD cards that are specifically designated for use with dash cams. You can find our recommendations on our website: www.rexingusa.com/memory-card/.
Note : Before inserting or removing a memory card, first ensure you’ve powered down the device.
Inserting a memory card:
1. If the device is powered on, press and hold the Power button to power down.
2. Insert the card in the orientation shown.
3. Push the card into the slot, listening for a click sound which signals the card is securely inserted.
24
©2018 REXING All Rights Reserved
V1P Pro Manual
Removing the Memory Card
Before removing a memory card from your computer, you must first unmount it for safe removal.
With the device powered down, press down on the memory card until you hear a click. Gently remove your finger (or other pressing object) to allow the spring release to push the memory card out of the slot.
Do not remove the memory card while the device is transferring or accessing information. Doing so can result in data loss or corruption, or damage to the memory card or device. Rexing is not responsible for losses that result from the use of damaged memory cards, including the loss of data.
25
©2018 REXING All Rights Reserved
V1P Pro Manual
Formatting the Memory Card
Before formatting your memory card, always remember to make backup copies of all important data stored on the device.
The manufacturer’s warranty does not cover loss of data resulting from user actions.
For best results, format the memory card using the Format function on your camera.
It’s recommended that you format your memory card after transferring files to your computer, or at least once a month.
Using your camera to format a memory card:
1.
Upon turning on the camera, press the REC button to stop recording.
2.
Press the MENU button twice to enter the Setup Menu.
3.
Use the REC and MIC buttons to navigate to the "Format" option.
4.
Press OK to confirm your selection.
5.
You will be notified that all data will be deleted. Scroll down to “OK” and press the OK button to confirm.
If you followed the instructions above, you should see a blue box asking you to please wait while the card is being formatted. Formatting should only take a moment, and you will be taken back to the Setup Menu once formatting is complete.
26
©2018 REXING All Rights Reserved
V1P Pro Manual
Turning the Device On and Off
Press and hold the Power button for a few seconds to turn on the device. A welcome message will be displayed onscreen.
To turn off the device, again press and hold the Power button for a few seconds. A goodbye message will be displayed onscreen.
The V1P Pro will switch on and off automatically if you keep it connected using the car charger. The camera will automatically start recording when powered on.
Note: If your car cigarette lighter provides constant power, the unit may not turn on and off automatically with the car.
27
©2018 REXING All Rights Reserved
V1P Pro Manual
Basic Operation
Automatic Recording
The device will automatically turn on and begin recording once it receives power, such as when you start your car. The indicator and the red dot icon on screen should flashing while recording.
Display Control
To switch between camera views on the LCD display, hold the MIC button. Your display setting won’t affect the way recordings are captured.
On the rear camera, you can toggle the built-in switch to horizontally flip the rear camera image.
Locking Videos
While recording, you can press the OK button to manually lock the current video clip. This will ensure that Loop Recording won’t overwrite the clip when the memory card is full. You can also lock videos after recording by using the
Protect function in the Playback Menu. Locked videos can be found on the memory card under “ \CARDV\MOVIE\ RO”.
Automatic Shutdown
Once power is disconnected, the dash cam will shut down within 2 seconds.
Using Wi-Fi
In Video Recording Mode, while recording is stopped, hold the REC button to enable Wi-Fi. For detailed instructions on how to use Wi-Fi, see page 29 – Wi-Fi
Connect.
28
©2018 REXING All Rights Reserved
V1P Pro Manual
Wi-Fi Connect
Use your mobile device to download the “Rexing Connect” app from the App
Store or Google Play Store.
After you’ve done this, follow the instructions below:
1.
Dash cam: In Video Recording Mode, access the Wi-Fi function by holding
REC (this can also be done by enabling the Wi-Fi feature in the Setup
Menu).
2.
Mobile device: Navigate to your device’s Wi -Fi settings and connect to the
WiFi name that’s shown on the dash cam after “SSID:”. When prompted for a password, enter the password shown on the dash cam after “PWA2:”.
3.
Mobile device: Once connected to the dash cam Wi-Fi, open the Rexing
Connect app. From there, press the “Connect” button to connect to the dash cam interface.
4.
Dash cam: Once connected, the screen should switch to the camera view and display a “WiFi Connected” message.
Using the Rexing Connect app, you can view a live preview of the dash cam screen, start / stop recording, as well as view and save your captures with your mobile device.
To exit Wi-Fi, hold the REC button to return to Video Recording Mode.
For further instruction regarding the Wi-Fi Connect feature, please visit www.rexingusa.com/wifi-connect/.
29
©2018 REXING All Rights Reserved
V1P Pro Manual
Video Settings
These settings affect your video recordings. In Video Recording Mode, press
REC to stop recording, then press MENU once to open the Video Menu.
Resolution
Default setting: FHD P30 + FHD P30 (1080p 30fps front and rear)
Set the video recording resolution.
Approximate recording time (dual-channel)
Memory Card Size
FHD P30 + FHD P30
Resolution
HD P30 + HD P30
Resolution
16GB 1.75 hours 2.5 hours
32GB 3.5 hours 5 hours
64GB
128GB
7 hours
14 hours
10 hours
20 hours
256GB 28 hours 40 hours
Note: Choosing a single-channel resolution such as UHD, QHD, etc. will disable recording with the rear camera.
30
©2018 REXING All Rights Reserved
V1P Pro Manual
Loop Recording
Default setting: 1 Minute
Video will be continually recorded in segments. When the storage limit is reached on the memory card, new recordings will automatically overwrite oldest recordings. Locked video files on the memory card will remain protected, and won’t be overwritten by Lo op Recording.
Note: Turning Loop Recording off will require you to manually clear recordings from your memory card whenever storage is full. We highly recommend keeping Loop Recording enabled.
WDR (Wide Dynamic Range)
Default setting: On
The camera automatically adjusts exposure settings to provide balanced lighting and clear video.
Exposure
Default setting: +0.0
Manually adjust the camera’s exposure value to brighten or darken recordings.
Positive values brighten recordings, while negative values darken them.
31
©2018 REXING All Rights Reserved
V1P Pro Manual
Record Audio
Default setting: On
Allows you to enable or disable audio recording with your videos.
You may choose to record audio with video, or turn off the microphone so that all recorded videos will be muted.
Note: You can also use the MIC button to toggle auto recording.
Date Stamp
Default setting: On
Stamp the date and time to the bottom of your videos. Note that the date and time stamp cannot be removed from videos if this feature was enabled at the time of recording.
Gravity Sensing
Default setting: Low
If a change in gravitational forces is detected, such as in the event of a vehicular accident, the g-sensor will signal to the camera, and an automatic file lock will be placed on the current video, preserving your most crucial footage.
Locked videos can be found on the memory card under “ \CARDV\MOVIE\ RO”.
Note: Locked video files won’t be erased by Loop Recording, they will remain on the memory card until they are manually deleted, or when the card is formatted.
32
©2018 REXING All Rights Reserved
V1P Pro Manual
Plate Number
Default setting: Off
Enter your vehicle plate number. The plate number will be displayed at the bottom of your videos.
To enter your license plate number:
● REC / MIC – Change current value
● OK – Move to next value
● MENU – Confirm setting
33
©2018 REXING All Rights Reserved
V1P Pro Manual
System Settings
Press MENU twice to open the Setup Menu (in Video Recording Mode, you must first stop recording, done by pressing REC ).
Wi-Fi
Default setting: Off
Turn this feature on to temporarily enable Wi-Fi mode (See: Page 29).
Date/Time
Set the time and date on your device.
To enter the date/time:
● REC / MIC – Change current value
● OK – Move to next value
●
MENU – Confirm setting
Auto Power Off
Default setting: Off
When enabled, this feature allows the device to shut down after a period of time in which the camera isn’t recording.
Device Sound
Default setting: On
Enable or disable the device’s sound effects.
34
©2018 REXING All Rights Reserved
V1P Pro Manual
Language
Default setting: English
Set your preferred device language.
Frequency
Default setting: 60Hz
Power supply specification used in your country or geographical region. United
States users should use 60Hz (default).
Screen Saver
Default setting: Off
Specifies the duration for which the display will stay on after the device is powered on. Having this setting disabled (default) will keep the display on constantly. You can press any button to wake the device from screen saver mode.
Daylight Saving
Default setting: Off
When enabled, time is advanced forward by 1 hour to match daylight savings time.
GPS
Default setting: mi/h
Display speed information at the bottom of your recordings .
35
©2018 REXING All Rights Reserved
V1P Pro Manual
Update Time of GPS
Default setting: Off
Updates the time automatically with your time zone.
Format
Performing this operation will format the memory card, clearing it of all files.
Note: Locked videos will also be cleared, so ensure you have backed up your important footage before formatting the card.
Default Setting
Performing this operation will reset all settings to their default values.
Version
Displays the current device firmware information.
36
©2018 REXING All Rights Reserved
V1P Pro Manual
Photo Settings
These settings affect your still photo captures. Hold MENU button 3 seconds to enter the Photo Mode. In Photo Mode, Press MENU once to open the Still
Menu.
Capture Mode
Default setting: Single
Sets a timer that counts down before capturing images.
Resolution
Default setting: 5M
Set the pixel resolution for captured images. Higher resolution images are more detailed, but take up more space on the memory card.
Quality
Default setting: Fine
Set the quality level of captured images. Lower quality images will take up less space on the memory card, but they are more visually compressed than higher quality images.
Sharpness
Default setting: Normal
Automatically enhance images for a clearer, more distinct picture.
37
©2018 REXING All Rights Reserved
V1P Pro Manual
White Balance
Default setting: Auto
Adjust the white balance for different lighting environments. When set to Auto, the camera will automatically determine the appropriate white balance for each shot.
Color
Default setting: Normal
Overlay a color effect for captured images. When set to Normal, no overlay is applied.
ISO
Default setting: Auto
Adjust the camera's sensitivity to light when taking photos. The higher the ISO, the better the camera operates in low light, although images are produced with more noise (grainy-looking).
Exposure
Default setting: +0.0
Adjust the camera exposure value to manually brighten or darken your images.
Anti-Shaking
Default setting: On
When enabled, the camera will automatically reduce the amount of blurriness resulting from quick or “shaky” movement.
38
©2018 REXING All Rights Reserved
V1P Pro Manual
Quick Review
Default setting: Off
Upon capturing an image, the image will be previewed on the display for a few seconds before returning to Photo Mode.
Date Stamp
Default setting: Date/Time
Apply a date and/or time stamp to captured images (works similarly to the Date
Stamp function in the Video Menu).
39
©2018 REXING All Rights Reserved
V1P Pro Manual
Playback
Video recordings from the front and back cameras will be stored in chronological order on the memory card for easy navigation and playback.
Camera Playback Mode
To play back recordings on your device:
● Switch to Playback Mode by holding the MENU button.
● Use the REC and MIC buttons to browse your videos.
● Press OK to play back a selected recording.
● During playback, press OK to stop playback.
● FAST FORWARD : During playback, press the MIC button one or more times to increase playback speed (2X / 4X / 8X).
● FAST REWIND : During playback, press the REC button one or more times to decrease or reverse playback speed (-2X / -4X / -8X).
To delete a selected recording:
1.
In Playback Mode, use the REC and MIC buttons to browse your videos.
2.
Once you find the recording you want to delete, press MENU to view options.
3.
Press the MIC button to scroll down to "Delete".
4.
Press OK once to view options to "Delete Current" recording or "Delete All" recordings.
5.
With “Delete Current” selected, press OK .
6.
W hen prompted with “Erase This?” press the MIC button to scroll down to
"OK" and press OK to delete the selected recording.
40
©2018 REXING All Rights Reserved
V1P Pro Manual
To delete all recordings:
1.
In Playback Mode, press MENU to view the Playback Menu.
2.
Press the MIC button to scroll down to "Delete".
3.
Press OK once to view options to "Delete Current" recording or "Delete All" recordings.
4.
With “Delete All” selected, press OK .
5.
When prompted with “Erase All Images?” press the MIC button to scroll down to "OK" and press OK to delete all recordings.
Computer Playback
Recommended Media Players: QuickTime Media Player / VLC / Windows
Media Player
Using an SD card adapter
Insert your Micro SD card into an SD card adapter, then insert the SD card adapter into your computer or card reader to access your card storage. Your videos will be stored under “ \CARDV\ MOVIE”.
Using a USB cable
Connect your camera to your computer using the provided USB cable and select “Mass Storage” to access your card storage. Your videos will be stored under “ \CARDV\ MOVIE”.
Locked files
Locked videos can be found on the memory card under “ \CARDV\MOVIE\ RO”.
41
©2018 REXING All Rights Reserved
V1P Pro Manual
GPS Playback
You can play back your recordings in a specialized application which allows you to view speed and location information alongside your footage.
Minimum System Requirements
Operating System: Windows 7, 8, or 10
Display Resolution: 1280x720
Installing the application:
1.
Locate your dash cam at support.rexingusa.com to access the GPS
Playback software.
2.
Download the zip folder containing the software installer.
3.
Unzip the folder to access the installer file contained within.
4.
Open the installer and follow the instructions to install the GPS Playback software to your computer.
5.
Once installed, you may launch the application.
Opening a GPS video file:
1.
Once you’ve opened the application, navigate to the top menu bar and click File > Open to browse through your files.
2.
Navigate to your video file you want to add to the playback queue, select it and click “Open” to load it into the application. You may also select multiple videos at once.
3.
After a brief loading period, the (first) video should begin playing back automatically, displaying speed and location information in real time along the right-side panels.
42
©2018 REXING All Rights Reserved
V1P Pro Manual
Playback
Beneath the video is a playback bar with a handle which you can drag to skip to any time in the video. Beneath that, there’s a volume control slider, as well as previous, rewind, pause/play, fast forward, next, and stop buttons.
Additional Controls
Snip: Save the current frame of video as an image (PNG).
Full Screen: View the video in full screen (double-click the video to exit).
Settings
In the settings menu, you may change your language from English to Chinese,
Japanese, or Vietnamese. You may also change your unit of speed measurement from MPH to KM/H. Additionally, you have the option to change the map application used from Google Maps to Baidu Maps.
43
©2018 REXING All Rights Reserved
V1P Pro Manual
Troubleshooting
Updating Firmware
Please note that we only recommend updating your firmware if you experience issues with your camera.
Installing incorrect firmware can damage your device. Identify the correct firmware for your camera by following the prompts on the rexingusa.com firmware portal.
To update your camera’s firmware:
1.
Format the memory card using the Format function (See: Page 26).
2.
Take note of your firmware version number (See: Page 36 – Version).
3.
On a computer, visit the firmware section of rexingusa.com and follow the prompts to locate the correct firmware for your camera.
4.
Download the firmware zip file to your computer.
5.
Unzip the file.
6.
Move the resulting file (.bin) to the root of your memory card.
7.
Safely eject card from computer, then insert into your unpowered camera.
8.
Turn the camera on by connecting to a power source.
9.
The camera will update automatically. The screen will stay off but the status light will stay on for up to 1 minute while the firmware updates.
10.
(Important) After updating, format the memory card once more. Failure to do this will result in the camera attempting to update the firmware every time it’s powered on.
11.
After formatting, hold the Power button to reboot the camera. Do not disconnect the camera from the power source.
12.
Upon reboot, you may disconnect your camera from power.
44
©2018 REXING All Rights Reserved
V1P Pro Manual
Common Solutions
Problem Possible Cause(s) Solution(s)
Images are not being saved
Rear camera isn’t recording video
None of the buttons are responding
Memory card is full or malfunctioning
Image not being saved before the device is powered off
Format memory card or replace with a new one
Make sure to stop recording before shutting down
Rear camera is not maintaining a stable connection
Processing error or faulty device operation
Memory card contains errors, or is damaged
Check the Resolution setting, ensure that you are recording in
“FHD P30+FHD P30” or “HD
P30+HD P30”
Use a new rear camera cable
Press the RESET button to restart the camera
Press the buttons firmly to ensure that the button input is registered
Format the memory card. If issue persists, replace the memory card
45
©2018 REXING All Rights Reserved
V1P Pro Manual
MENU button isn’t responding
Device won’t turn on or it keeps rebooting
Camera is recording
Power source is insufficient
Press REC to stop recording before accessing the menu
Ensure you are using a proper connection for charging your device while driving. Always use
Rexing power supplies
Memory card won’t stay in
Memory card isn’t compatible
Memory card is too thin
Use your nail or a coin to push the memory card in until it clicks
Use a new memory card
Memory card isn’t recognized
(cluster error)
Memory card needs to be formatted
Format the memory card. If issue persists, replace the memory card
Can’t find locked files
When you lock a file, it only saves the current recording. The remainder of the video may be in a separate file
Check the memory card RO folder
Screen powers off unexpectedly
Screen Saver feature is enabled
Disable Screen Saver feature
Restore to default settings
46
©2018 REXING All Rights Reserved
Keeps turning off
V1P Pro Manual
Memory card isn’t compatible
Camera isn’t getting continuous power
Restore to default settings
Get a replacement power cord
Use a new memory card
Screen is frozen
Memory card is defective or corrupted
Format the memory card. If issue persists, replace the memory card
Unable to record videos
Memory card is full
Memory card is defective or corrupted
Make sure the red light is blinking while recording
Check remaining space on memory card and delete files if necessary
Restore to default settings
Format the memory card. If issue persists, replace the memory card
47
©2018 REXING All Rights Reserved
V1P Pro Manual
Stops recording randomly
Memory card isn’t compatible
Loop Recording is off
Restore default settings
Format the memory card. If issue persists, replace the memory card
Turn Loop Recording on
Loop Recording isn’t functioning
G-sensor sensitivity is too high
Memory card is full
Make sure Gravity Sensing is on low sensitivity
Format the memory card
Memory card is full
Loop Recording is off
There are too many locked videos
Make sure Gravity Sensing is on low sensitivity
Turn Loop Recording on
Clear some locked files
Format the memory card
Stops recording after 1-3 looped files
Insufficient power is being supplied to the device
Memory card isn’t compatible
Restore to default settings
Replace power cord
Format the memory card. If issue persists, replace the memory card
48
©2018 REXING All Rights Reserved
V1P Pro Manual
“File error" is encountered when trying to play back pictures or video
Memory card is corrupted
Format the memory card. If issue persists, replace the memory card
Hazy images Lens is dirty
Carefully clean dust or fingerprints from the lens with a microfiber cloth
Horizontal stripes appear on images
The Frequency setting is incorrect
Change the Frequency setting to match the power supply used in your country or geographical location. US users should select the 60Hz option, SG/MY users should select the 50hz option
Auto On/Off isn’t working
Car charging port has continuous flow of power
This feature can only work if it is being used in a charging port that turns off with the vehicle
GPS isn’t connecting
Camera firmware is out-of-date Camera mounting position is blocking GPS signal
Update firmware (See: Page 44)
Mount your camera to a different location in your vehicle
49
©2018 REXING All Rights Reserved
V1P Pro Manual
Losing/Resetting date
Need to update
Firmware
WiFi isn’t connecting
Update firmware
Mobile device isn’t connected to camera
Check Wi-Fi settings on your mobile device, ensure you are connected to the SSID shown on the camera
50
©2018 REXING All Rights Reserved
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement