NB North Bayou 1001070680 Monitor Arms & Stand User Manual

 E
®
NORTH BAYOU
A
Flexi Full Motion Desk Mount
Flexi Full Motion Desk Mount
Fits Most Displays Size: 17"-27"
Max Load: 4. 4-14.31bs (2-6.5kg)Single
VESA:75x75,100x100mm
Severe personal injury and property damage can result from improper installation or assembly.
Read the following warning carefully before beginning.
@ Products must be installed by professional or installer.
O If you do not understand the instructions or have any concerns or questions, please
contact a qualified local installer.
O Do not install or assemble if the product or hardware is damaged or missing, if you
require replacement parts, please contact you local distributor for assistance.
O This product fits most 17"-27" LCD / monitor; maximum weight of LCD / monitor:
6.5kg / 14.31bs.
O Installer-friendly and straight forward.
@ For safe installation, the desk you are mounting to must support minimum 3 times the
weight of the total load (the mount, the monitor and all accessories weight).
@ Do not use this product for other than the original designed.
@ This product contain moving parts, please use with caution.
@ When installing monitor, please do not damage electrical wiring or power source.
@ Installation and routing of monitor cables on the monitor bracket must comply with
electro-technical regulations.
@ Importantly, mains- and data-cables must be secured against twisting and squeezing or
shearing.
e The manufacturer Will bear no responsibility to the desk of mounting, or incidental
or consequential damages arising thereof.
O The manufacturer disclaims any liability for the modifications, improper installation, or
installation over the specified weight range. The manufacturer will not be liable for any
damages arising out of the use of , or inability to use, the product.
@ This product is designed for indoor used only, use of this product outdoor could lead to
product failer and severe personal injury.
A This product contains a high pressure gas spring, fire and percussion prohibited. Also it is
strictly prohibited to dismantle without professionals. Please return to the manufacturer or
hand over to professional agencies if the product is abandoned. In order to ensure the
performance of gas spring, full direction adjustment of the product arm is recommended
several times per month.
A All images are for reference only. As product in kind prevail.
We reserve the right to modify or alter instructions. No modification or alteration without formal
N
F160
Installation Manual
Install mountattable edge
or
Install mount on desk.
Part list
Le JR ==
> a —>
es”
| J)
Li
й gy
»
OS
©
©
|
a
LA!
Ma À
8 SE
эл = ы
A
[
64
NE
¡UN Aa
SN
A |
IS
Note:
USB lines
not supplied.
Ensure screws are
secured firmly.
Notes : Please install "line out" at base 8
Cm
(M4x12)-8pcs (M5x12)-8pcs
C
(M6x12)-6pcs
№ пойсе.
Symbols
, , , ‚ + : Torque increased
E, Tightening Direction Ct — : Torque reduced
— + E AENA
RA SD — SE AE HEA
, , ‚ + : Torque increased
O loosening Direction + $ — :Torque reduced
+ ERE A
NA п.
ВАЛИ Ve=| Eta
y Phillips Screwdriver By Hand
@ ET FT
7 Open-End Wrench Hex Wrench
Q FOR NAT
Adjustment Pencil
Optional Hand Drill
OPT AJ i FHS
‘ Remove Star Wrench
\_ Br ZARF
N
A. USB lines installation: ( Users wish )
(— [Step 1]
_ “line in" to PC as shown fig-3.
B1, Table edge installation:
[Step 1]
2.
Ensure screws are
secured firmly.
Ensure screws are
secured firmly.
4001071405 A2 \
B2, Grommet installation:
77
[Step 1]
= in у
SAN
4 ZA
1 Oro 1088
A
Ensure screws are
secured firmly.
E
(4mm)
N
[Step 2]
Ensure screws are
secured firmly.
Adjustable parameters
À
<
E
(220°
>
360°
2S +35° /-50%
250mm
|
|
0~95mm
A
For grommet
Max Load: 4. 4-14.31bs (2-6.5kg)Single
N
J
C. Power and display lines installation
Warning:
Ensure screws are
secured firmly.
N
D. Display installation
( [Step 1] A
VESA:75x75mm,100x100mm
N pe
x75mMo,
. VS S Na
о o A/B
o
E. Torque adjustment
"+": Torque increase direction shown fig-2
"—": Torque decrease direction shown fig-2
F. Setting tilt angle position
a8
J
Notes: Ensure display weight is within load range.
1.If display can be hovered at any height after display installed.
No adjustment needed.
2.If display lift up automatically after display installed, adjust the
following: One man hand press down the screen, the other
wind set screw at the bottom of upper arm at joint to '-"
direction to reduce torque by using G, 5mm. Allen key as
shown in Fig-E1 and E2 until display can be hovered at any
point of positions.
3.If display sit at the lowest position after installation, repeat #2
procedures but winding set screws То ' + ' direction to increase
torque as Fig-E1l and E2 until display can be hovered at any
\_ point of positions.
Warning:
Do not fully
re-thread screw.
"+" Tighten
“-" Loosen
Ne
H. Display rotation
Г 360° г =
Only dispay comes with central gravity
\_ will has the best performance.
4001071405 A2 \
fo O
TENSIÓN ADJUSTMENT
AFTER WALL MOUNT INSTALLATION
Warning
Do not adjust tension without putting on display.
1.Ensure display has been put onto mount.
2.Read your display packaging or manual to find
out display net weight.
3.Ensure display net weight between 4.4-14.31bs
(2.0-6.5kg).
Adjustment sign
— +
Anti-clockwise reduce clockwise to increase
tension(carry less weight) tension(carry more weight)
Warning!
Add:58, South of Xinxing Road,
Economic Development Zone.
Kunshan City, Jiangsu Province, China.
215333.
NORTH BAYOU
TEL: 86-512-57971777
www.nbavmount.com.cn FAX: 86-512-57970776
< J