advertisement
HIIT Training Fan Bike
IMPORTANT: Read all instructions carefully before using this product.
Retain this owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to change without notice.
2225.2-082218
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE.
STOP. Contact customer service if you have any questions regarding assembly or proper operation of the machine.
Email us at:
[email protected]
Or call us at:
1-844-641-7920
Hours:
8:00 am to 5:00 pm (PST)
Monday thru Friday
TABLE OF CONTENT
SERVICE ------------------------------------------------------------------------ 2
LABEL PLACEMENT --------------------------------------------------------- 3
IMPORTANT SAFETY GUIDELINES ------------------------------------- 4
OVERVIEW DRAWING ---------------------------------------------------- 6
PART LIST --------------------------------------------------------------------- 7
HARDWARE & TOOLS PACK -------------------------------------------- 9
ASSEMBLY -------------------------------------------------------------------- 10
CONSOLE --------------------------------------------------------------------- 22
ADJUSTMENTS --------------------------------------------------------------- 25
TROUBLESHOOTING & MAINTANCE---------------------------------- 27
TRANSPORT & STORAGE ------------------------------------------------ 29
WARRANTY -------------------------------------------------------------------- 30
PARTS REQUEST FORM--------------------------------------------------- 31
1
SERVICE
IMPORTANT: FOR NORTH AMERICA ONLY
For damaged or defective product, questions, replacement parts or any other service support, please contact our customer service department by the below methods:
For The Best Service, please Email: [email protected]
Response Time: 1-2 Business Days
Emailing us with the information above will be the best method to receive a response during peak business hours
Website: www.paradigmhw.com
Toll-Free:
1-844-641-7920
(8:00 AM - 5:00 PM Pacific Standard Time, Monday thru Friday)
Response time may vary via calling
Please have the following information ready when requesting for service:
Your name
Phone number
Model number
Serial number
Part number
Proof of Purchase
For damaged or defective product please contact our customer service before returning to the store.
Paradigm Health & Wellness, Inc.
1189 Jellick Ave.
City of Industry, CA 91748, USA
2
LABEL PLACEMENT
3
IMPORTANT SAFETY GUIDELINES
Read all instructions before using the equipment. When using the equipment, basic precautions should always be followed.
WARNING - To reduce the risk of injury to persons, read and under the following:
1. Make sure your equipment is correctly assembled before you use it.
2. Be sure all screws, nuts, and bolts are tightened prior to use.
3. Before using this equipment, we recommend doing warm ups and stretching of the major muscle groups.
4. Only one person should be using the equipment at a time.
5. Never operate this Equipment if it is damaged, if it is not working properly, has been dropped, or damaged. If a problem is encountered contact Customer Service before using the equipment again.
6. Always use this equipment on a clear and level surface.
7. For household use only.
8. Do not use outdoors or near water.
9. Use this product only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
10. Do not wear loose clothing when using the equipment.
11. Never drop or insert any object into any opening.
12. If at any time you feel faint, light-headed, or dizziness while operating the equipment, stop exercising immediately. You should also stop exercising if you are experiencing pain or any discomfort.
13. For any problems contact customer service. Servicing should be performed by an authorized service representative. Our contact number is on the service page.
14. DO NOT pedal in reverse.
15. This product requires a minimum of 6 square feet of space for safe operation.
16. ASSEMBLY ALL HARDWARE IN THE ORDER THAT IS SHOWN IN THE ILLUSTRATIONS
17.
Warning:
- Risk of Personal Injury - Consult with your personal physician to see if this exercise equipment is appropriate for you. This is especially important for people with pre-existing health problems. Do not use this equipment without your physician's approval.
18.
Warning:
- Risk of Personal Injury – Do not allow children to use this machine.
19.
Warning:
- Risk of Personal Injury - Keep children under the age of 13 away from the machine.
20.
Warning:
- Risk of Personal Injury
– Keep body parts, hair, loose clothing, and jewelry clear of all moving parts.
21.
Warning:
- Risk of Personal Injury Do not attempt to service the unit yourself. Discontinue use and contact customer service.
22.
Warning :
- To Reduce The Risk Of Personal Injury - Read And Understand All Read The
Instructions Before Using the Bike.
23.
WARNING:
CANCER AND REPRODUCTIVE HARM --
WWW.P65WARNINGS.CA.GOV.
4
IMPORTANT SAFETY GUIDELINES
Do not use this equipment if you have any of the following conditions or ailments:
Pregnancy
Extreme obesity
Middle ear infection
Hiatus hernia or Ventral hernia
Glaucoma, retinal detachment or conjunctivitis
Use of anticoagulants including Aspirin in high doses.
Spinal injury, Cerebral Sclerosis, or acutely swollen joints
Heart or circulatory disorders for which you are being treated
High blood pressure, Hypertension, Recent stroke or Transient Ischemic attack
Bone weaknesses including Osteoporosis, Unhealed fractures, Modular pins, or surgically implanted orthopedic supports.
Do not exceed the maximum rated weight (load):
The Maximum Weight Capacity for this product is 300lbs/136kgs.
The Maximum User Height for this product is 6’3”/190cm.
Retain this owner’s manual and keep the original purchase receipt for future reference.
SAVE THESE GUIDELINES
5
OVERVIEW DRAWING
6
No. Description
1 Main Frame
2 Front Stabilizer
3 Nylon Nut M8×P1.25
4 Wheel
5 Hex Bolt M8×P1.25×40L
6 Front Stabilizer End Cap
7 Hex Nut 3/8"-16
8 Foot Pad
9 Foot Pad Bracket
10 Rear Stabilizer
11
Self`-Tapping Phillips Screw
4X10L
12 Rear Stabilizer End Cap
13 Hex Bolt M5×P0.8×15L
14 Anti-Slip Pad
15 Hex Bolt M10×P1.5×55L
16 Washer ψ27×ψ10.5×2t
17 Console
18 Screw
19 Handlebar
20 Hex Bolt M6×P1.0×6L
21 Knob
22 VBlock φ23×23L
23 Hex Bushing
24 End Cap
25 Handlebar Post
26 Hex Bolt M5xP0.8x10L
27 Hex Bushing
28 Front Post
29 Washer d8XD16X1.5t
30 Hex Bolt M8XP1.25X16L
31 Hex Bolt M8XP1.25X15L
32 VBlock with magnet φ23×23L
33 Seat Post
PARTS LIST
2
3
1
2
1
1
1
4
2
2
6
5
1
1
1
4
4
1
4
2
4
1
4
5
3
1
Q ’ty No.
1 34 Seat
1
2
Description
35 Hex Bushing
36 Seat Slider
2
2
2
37 Knob
38 Pressing Block
39 Seat Bushing
40 Sensor Bracket
41 Phillips Screw M5×P0.8×8L
16
42L Left Pedal
42R Right Pedal
43 Crank Cap
44 Flange Nut M10×P1.25×7
45
Wave Washer φ20×φ10.2×1t
46L Left Crank
46R Right Crank
47 Hex Bolt M6xP1.0x15L
48 Hex Bushing 38x2.5t
49 Washer 13x6x1t
50 Belt Wheel
51 Magnet
52
Axle φ25xφ20x148L
53 Nylon Nut M6
54 Bearing 6004 ZZ
55 Nylon Cap M20×P1.0×12t
56
Sleeve φ27x27L
57 Press Wheel
58 Bearing 6001ZZ
59 C-Ring R28
60 C-Ring C12
61L Left Cover
61R Right Cover
62L Left Protective Cover
62R Right Protective Cover
7
2
2
1
1
1
4
1
1
1
1
4
1
1
1
1
1
1
4
1
4
2
2
1
Q’ty
1
2
1
2
1
1
1
1
1
1
PARTS LIST
No. Description
63 Front Protective Cover
Q’ty No.
2
2
Description
78 Hex Bolt M5×P0.8×12L
79
Washer φ10xφ5x1t
64 Rear Protective Cover
65 Self-Tapping Phillips Screw 4X20L 6
66 Bottle Holder 1
67 Hex Cap Bolt M5×P0.8×12L 2
80 Hex Nut M12*P1.25*7t
81A Upper Console Wire
81B Lower Console Wire
68 Eye Bolt
69 U-Bracket
70 Hex Nut M6xP0.8
71 Belt
72L Left Cage
72R Right Cage
73 Phillips Screw M4xP0.7x12L
74 Packing
75 Clip
76 Protective Cover
Round Head Hex Bolt
77
M5xP0.8x15L
2
2
2
1
1
1
6
6
6
2
4
82 Fan Axle
83 Hex Screw M5xP0.8x16L
84 Fixed Plate
85 Fan Plate 187.5x50x20x2.5t
86 Fan Plate 197.5x50x20x2.5t
87 Nylon Nut M5xP0.8
88 Axle Wheel
89 Wire Plug
90 Spring Washer Ф8
91 Thread Sealant
8
1
18
1
4
2
18
1
Q’ty
6
6
4
1
1
1
6
1
HARDWARE & TOOL PACK
4mm Allen
Wrench 1pc
(15) Hex Bolt
4PCS
(16) Washer
4PCS
(91) Thread Sealant
1PC
5mm Allen
Wrench 1PC
6mm Allen Wrench with
Phillips Screwdriver
1PC
Combination Wrench 1PC
13,14,15,17 Wrench 1PC
9
ASSEMBLY
Tool:
6mm Allen Wrench with
Phillips Screwdriver
1PC
Step 1
1a. Rear Stabilizer Installation: Lift up the rear of the Main Frame (1) , and attach the Rear
Stabilizer (10) onto the rear curve of the Main Frame (1) with two Hex Bolts (15) and two
Washers (16). Use the 6mm Allen Wrench with Phillips Screwdriver to tighten the Hex Bolts
(15) until they are firm and secure.
NOTE: Must assemble the Rear Stabilizer (10) before the Front Stabilizer (2).
Hardware:
(15) Hex Bolt
2PCS
(16) Washer
2PCS
10
ASSEMBLY
Tool:
6mm Allen Wrench with
Phillips Screwdriver
Styrofoam Block
Step 2
2a. Front Stabilizer Installation: Lift up the front of the Main Frame (1) , and place a block of
Styrofoam under the machine to help hold the frame up, then attach the Front Stabilizer (2) onto the front curve of the Main Frame (1) with two Hex Bolts (15) and two Washers (16). Use the
6mm Allen Wrench with Phillips Screwdriver to tighten the Hex Bolts (15) until they are firm and secure.
Hardware:
(15) Hex Bolt
2PCS
(16) Washer
2PCS
11
ASSEMBLY
Tool:
91
(91) Thread Sealant
1PC
Step 3
3a. Applying the Thread Sealant: Fully coat the threads of both Left Pedal (42L) & Right Pedals
(42R) with Thread Sealant (91) before the pedal assembly of Step 4 .
NOTE: Before applying Thread Sealant (91), make sure the threaded shaft is clean.
12
ASSEMBLY
Tool:
Step 4 Combination Wrench 1PC
NOTE: The Cranks and Pedals are marked “R” for Right and “L” for Left .
4a. Installing the Left and Right Pedal
Left Pedal: Insert the Left Pedal (42L) into the threaded hole in the Left Crank (46L) . Insert the treaded shaft straight into the crank. Hand-tighten the pedal shaft in a COUNTER-CLOCKWISE
↺ direction. Use the Combination Wrench to fully tighten the pedal shaft COUNTER-CLOCKWISE
↺
.
Right Pedal: Insert the Right Pedal (42R) into the threaded hole in the Right Crank (46R) . Insert the treaded shaft straight into the crank. Hand-tighten the pedal shaft in a CLOCKWISE
↻
direction.
Use the Combination Wrench to fully tighten the pedal shaft CLOCKWISE
↻
.
NOTE: Allow the Thread Sealant (91) from Step 3 to cure for at least 12 hours before use.
13
ASSEMBLY
Tools:
5mm Allen
Wrench 1PC
13,14,15,17 Wrench 1PC
Step 5
5a. Removing the Hardware from the Front Post: Use the 5mm Allen Wrench to remove the five Hex Bolts (30) , one Hex Bolt (31) , six Spring Washers (90) , and six Washers (29) from the Front Post (28) .
5b. Installing the Front Post: Slide the Front Post (28) onto the Main Frame (1) . Reinstall the previously removed five Hex Bolts (30) , one Hex Bolt (31) , six Spring Washers (90) , and six
Washers (29). Securely tighten the Bolts (30) using the 5mm Allen Wrench and the Bolt (31) in using the 13,14,15,17 Wrench provided.
NOTE : The Bolt (31) goes on the underside of the bike frame
14
ASSEMBLY
Step 6
Tool:
4mm Allen
Wrench 1pc
6a. Removal of Hardware for Installation: Use the 4mm Allen Wrench to remove the Hex Bolt
(26) from the Handlebar Post (25) .
6b. Installing the Handlebar: Slide the Handlebar (19) onto the Handlebar Post (25) . Reinstall the previously removed Hex Bolt (26) and securely tighten it using the 4mm Allen Wrench provided.
15
ASSEMBLY
Step 7
Fig. A
7a. Seat Post Installation: Loosen the Knob (37) and insert the Seat Post (33) into the Main
Frame (1) . Adjust the Seat Post (33) into the suitable position and tighten the Knob (37) to lock the seat height.
NOTE: If the seat post does not fully insert, remove the seat post and push the Pressing
Block (38) back (SEE Fig. A). This will clear the opening for inserting the Seat Post (33).
16
Tool:
Combination Wrench 1PC
13,14,15,17 Wrench 1PC
Fig. B
ASSEMBLY
Step 8
8a. Installing the Seat: Mount the Seat (34) onto the post on top of the Seat Slider (36) and tighten the nuts on the underside of the Seat (34) using the 13,14,15,17 and Combination Wrench provided.
NOTE: The seat angle can be tilted to improve riding comfort. Set a seat angle, fully tightening the nuts on the underside of the seat, and test the seat angle for optimal comfort. See Fig. B .
17
Tool:
4mm Allen
Wrench 1pc
ASSEMBLY
Step 9
9a. Hardware Removal: Remove the Hex Cap Bolts (67) from the Main Frame (1).
9b. Installing the Bottle Holder: Attach the Bottle Holder (66) to the Main Frame (1) with two
Hex Cap Bolts (67) that were previously removed . Tighten all the bolts using the 4mm Allen
Wrench provided .
18
ASSEMBLY
Fig. C
Step 10
10a. Connecting the Console Wire: Connect the Upper Console Wire (81A) from the Front
Post (28) with the Lower Console Wire (81B) from the Main Frame (1) as shown in Fig. C.
10b. After connecting the wires, insert the excess wire (81A & 81B) into the hole on the Main
Frame (1).
19
ASSEMBLY
Tool:
Fig. D
6mm Allen Wrench with
Phillips Screwdriver
1PC
Step 11
11a. Remove the Screws: Remove the Screws (18) from the back of the Console (17) .
11b. Installing the Console: Attach the Console (17) to the plate of the Handlebar (19) with the four Screws (18) that were previously removed. Tighten all the screws using the 6mm Allen
Wrench with Phillips Screwdriver provided .
11c. Connecting the Console: Insert the Upper Console Wire (81A) into the back of Console
(17) marked SENSOR as shown in Fig. D.
20
ASSEMBLY
Tool:
6mm Allen Wrench with
Phillips Screwdriver
Step 12
11a. Battery Installation: Loosen the screw that holds the battery cover in place to remove the battery cover from the back of the Console (17) . Insert 4 AA batteries into the console and then reattach the battery cover. Tighten the screw using the 6mm Allen Wrench with Phillips
Screwdriver provided .
NOTE: The console can ONLY be powered by four 1.5 volt AA batteries.
21
CONSOLE
START/PAUSE:
1. Begins the desired workout.
2. During workout, press once to pause and press again to resume a paused workout session.
3. The START button must be pressed to begin tracking the workout.
ENTER:
1. Press ENTER to save a value input while setting up a workout.
2. Note: Workouts only begin when the user presses the START Button .
MODE/RESET:
1. Press MODE during a workout to change the workout statistic being shown under the
CAL/MIN arc.
2. Display options are CAL, SPEED, RPM, and
SCAN.
3. SCAN will automatically alternate between CAL, SPEED, and RPM every 4 seconds.
4. Hold MODE for 3 seconds to reset the console back to the main screen.
UP BUTTON:
1. While setting up a workout, press to increase a value when the numbers are flashing.
DOWN BUTTON:
1. While setting up a workout, press to decrease a value when the numbers are flashing.
CLOUD FITNESS BUTTON:
1. Press this button to connect to the APP.
Changing Units of Measurement:
1. Press and hold ENTER and UP at the same time to change the units displayed from
Imperial (Miles) to Metric (Kilometers). There will be a Mi or KM displayed under the word distance in the top left corner.
Turn OFF button push beeps:
1. Press and hold UP and DOWN to disable the BEEP when a button is pushed. The console will BEEP one time to acknowledge the change is complete.
QUICK START WORKOUT:
1. Press START to immediately begin a workout at the main screen.
2. PAUSE the current workout to end the current work out and change to a Target Goal or HIIT
Workout.
3. The Quick Start Workout does not have an end point. Pausing the Quick Start Workout or 4 minutes of inactivity will end the workout.
22
Note: that programs only begin when the user presses
START.
CONSOLE
TARGET GOAL WORKOUT:
1. Use the TIME, CAL, and DIST buttons to set a target goal for Work Time, Calories Burned, or Distance Traveled.
TIME goals can be set from 5:00 to 99:00 minutes.
CALORIES goals can be set from 25 to 2000 calories burned.
DISTANCE goals can be set from 1.0 to 99.0 ML/KM.
2. Use the UP or DOWN buttons to change the value for the selected goal. Press and hold the buttons for the value to change quickly.
3. Press ENTER to set the goal value, press START to begin the workout.
4. When a Target Goal Workout is finished the console will BEEP 3 times to signal the end of the workout.
5. Total workout values (TIME, CAL, DIST, and MAX WATTS) will be displayed.
6. Press any button to end workout and return to main screen.
7. Note: The equipment can NOT do a Target Goal and HIIT workout at the same time.
8. Note: Only one Target Goal Workout can be set during a workout.
HIGH INTENSITY INTERVAL TRAINING WORKOUT (H.I.I.T.):
1. Use the 20/10, 30/90, CUSTOM INTERVAL buttons to set a HIIT workout.
A 20/10 HIIT Workout consists of 20 seconds of high activity followed by 10 seconds of low activity.
A 30/90 HIIT Workout consists of 30 seconds of high activity followed by 90 seconds of low activity.
A Custom HIIT Workout consists of a user-defined high activity period followed by a low activity period.
ROUND:
The total number of sets of high and low workout periods.
SPRINT:
Length of time for the high activity period.
20/10, 30/90 INTERVAL WORKOUT
SETUP
1. Press UP or DOWN to set the value of “ROUND”.
2. The number of rounds changes by
1, with a range of 1 to 99 rounds.
CUSTOM INTERVAL
WORKOUT SETUP
1. Press UP or DOWN to set the value of
“ROUND”.
2. The number of rounds changes by 1, with a range of 1 to 99 rounds.
3. Press and hold the UP or DOWN button to change the value quickly.
3. Press and hold the UP or DOWN button to change the value quickly.
4. Press START to begin the workout 4. Press ENTER to set the value for
“ROUND” and move on to the next section.
1. The “SPRINT” time is pre-set for the 20/10 and 30/90 HIIT programs.
2. This cannot be changed
1. Press UP or DOWN to set the value of
“SPRINT”.
2. The increments of time change by 5 seconds, with a range of 10 to 95 seconds.
3. Press and hold the UP or DOWN button to change the value quickly.
4. Press ENTER to set the value for
“SPRINT” and move on to the next section.
23
CONSOLE
RECOVER: Length of time for the low activity period.
1. The “RECOVER” time is pre-set for the 20/10 and
30/90 HIIT programs.
2. This cannot be changed
2. When HIIT Workout is finished the console will BEEP 3 times to signal the end of the workout.
1. Press UP or DOWN to set the value of “RECOVER.”
2. The increments of time change by 5 seconds, with a range of 10 to 95 seconds.
3. Press and hold the UP or
DOWN button to change the value quickly.
4. Press ENTER to set the value for “RECOVER.”
5. Press START to begin the workout, the custom workout will be saved on the console for future use.
Only one customer program can be saved.
3. Total workout values (TIME, CAL, DIST, and MAX WATTS) will be displayed.
4. Press any button to end workout and return to main screen.
5. Note: All HIIT workout programs begin with a “RECOVER” period followed by a “SPRINT” period.
6. Note: The console will “BEEP” and the display will “FLASH” 3 times to alert the user the change between a low intensity “RECOVERY” period and a high intensity “SPRINT” period.
7. Note: “ROUND” will count up by 1 every time a cycle of “RECOVER” and “SPRINT” is completed.
Additional Notes:
8. NOTE: The console turns on when pedaling is detected.
9. NOTE: The console shuts off automatically after 4 minutes of inactivity.
10. NOTE: The equipment can NOT do multiple Target Goals and HIIT workouts at the same time.
24
OPERATIONS & ADJUSTMENTS
Adjusting the Stability of the Bike
1. Turn the Foot Pads (8) on the Rear Stabilizer (10) as needed to level the recumbent bike.
2. Do NOT extend the Foot Pads (8) too far, as this will cause the bike to tilt and be off balance.
3. The 13,14,15,17 Wrench may be required to loosen the Foot Pads (8) on the Front
Stabilizer (2).
Adjusting the Seat Angle
1. Loosen the two Nuts on the underside of the seat.
2. Tilt seat angle.
3. Retighten the two Nuts on the underside of the seat.
4. Test the seat angle for comfort.
25
OPERATIONS & ADJUSTMENTS
Seat Height Adjustment
1. Turn the Knob (37) COUNTER-CLOCKWISE
↺
to loosen the post.
2. Adjust the seat up or down to your desired position.
3. Turn the Knob (37) CLOCKWISE
↻
to secure the seat again.
Do NOT raise the seat post over the STOP line.
Seat Slide Adjustment
1. Turn Knob (37) COUNTER-CLOCKWISE
↺ to loosen the seat.
2. Slide the seat to your desired reach.
3. Turn the Knob (37) CLOCKWISE
↻ to lock.
Handlebar Height Adjustment
1. Turn the Knob (21 ) COUNTER-CLOCKWISE
↺ to loosen the handles.
2. Slide the handlebar up or down to your desired position.
3. Turn the Knob (21) CLOCKWISE ↻ to lock.
Do not raise the handlebar post over the STOP line.
Handlebar Slide Adjustment
1. Turn Knob (21) COUNTER-CLOCKWISE
↺
to loosen the handles.
2. Slide the handlebar to desired reach.
3. Turn the Knob (21) CLOCKWISE
↻
to lock.
26
TROUBLESHOOTING
1. PROBLEM: The recumbent bike wobbles when in use.
1) SOLUTION: Turn the Foot Pads (8) as needed to level the bike.
2. PROBLEM: The display on the Console (17) does not turn on.
1) SOLUTION: Remove the Console (17) and verify that the Console (17) is properly connected to the Upper Console Wire (81A) wire.
2) SOLUTION: Check that the Upper Console Wire (81A) is securely connected to the Lower
Console Wire (81B) .
3) SOLUTION: Replace the batteries in the back of the Console (17).
3. PROBLEM: The bike makes a squeaking noise when in use.
1) SOLUTION: The hardware may be loose on the bike. Inspect all of the hardware and tighten any loose parts.
27
MAINTENANCE
WARNING: Before connecting any cables, make sure the METAL
PRONGS of the cables are NOT bent.
Correct Incorrect
Cleaning:
1. The bike can be cleaned with a soft clean damp cloth.
2. Do NOT use abrasives or solvents on the plastic parts.
3. Wipe your perspiration off the recumbent bike after each use.
4. Be careful not to get excessive moisture on the console display as this might cause an electrical hazard or the electronics to fail.
5. Keep the bike, especially the computer console out of direct sunlight to prevent screen damage.
6. Inspect that all assembly bolts, nuts, screws, and pedals on the machine are thoroughly tightened every week. Tighten any loose parts.
Battery Change for Console:
1. The console can ONLY be powered by 4 AA batteries.
2. A battery life indicator can be found at the top of the LCD display.
Thread sealant instruction:
1. If any parts need thread sealant applied, the parts must be cleaned before application.
Install the part and wait at least 12 hours for the sealant to cure after application. Use the bike only after the part applied with thread sealant has had time to cure.
28
TRANSPORT & STORAGE
Transporting the Bike
Push down on the Handlebar (19) with both hands until the wheels of the Front Stabilizer (2) make contact with the ground. Pull or push the bike to the desired work out area or storage area.
Gently lower the bike to the ground after transporting.
WARNING: always maintain both hands on the handle of the Handlebar (19) while transporting.
Storage
Store the bike in a clean and dry environment away from pets and children.
29
WARRANTY
MANUFACTURER’S LIMITED WARRANTY
Paradigm Health & Wellness warrants to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with Paradigm’s Owner’s
Manual. Paradigm’s obligation under this warranty applies to the following:
COMPONENT LENGTH OF WARRANTY
Structural Frame 10 years For Home Use Only
Parts 5 year For Home Use Only
Electronic/Wearable Parts 2 year For Home Use Only
(computer display, electronics, upholstery, foam, ball bearings, pulleys, belts, cables, wires, shocks, covers, tension, internal mechanism, wheels, pedals, knobs, accessories and hardware)
Exclusions from Warranty Coverage:
Paradigm does not warrant against and is not responsible for, and no implied warranty shall be deemed to cover, any product failure, product malfunction, or damages attributable to:
1. Improper installation and/or failure to abide by Paradigm’s installation guidelines;
2. Use of this product beyond normal home use, or in an application for which it was not designed;
3. Cosmetic items such as scratches, dents or discolorations;
4. Damage caused by normal wear and tear, vandalism, accidental or by animals;
5. Any act of Nature (such as fire, flooding, snow, ice, hurricane, earthquake, lightning or other natural disaster), environmental condition (such as air pollution, mold, mildew, etc.), or staining from foreign substances (such as dirt, grease, oil, etc.);
6. Normal weathering due to exposure to sunlight, weather and atmosphere which can cause colored surfaces to, among other things, flake, chalk, accumulate dirt or stains.
7. Improper operation, alteration, handling, storage, abuse or neglect of the products.
Paradigm, using its sole discretion, will either repair or replace free of charge any part(s) proven to be defective under normal home use. Any repair or replacement shall provide no new warranty coverage, but shall retain only the remaining portion of the original product’s warranty. This warranty is offered only to the original purchaser and is not transferable. Proof of original purchase is required.
Ordering Replacement Parts
Replacement parts can be ordered by emailing our customer service department:
[email protected]
Open Monday thru Friday 8:00 AM - 5:00 PM (PST).
When ordering replacement parts please have the following information ready:
1. Owner’s Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase
30
PARTS REQUEST FORM
Paradigm Health & Wellness, Inc.
EMAIL THIS FORM WITH YOUR RECEIPT OF PURCHASE TO
[email protected] *
NAME: _____________________________________________________________________________________
ADDRESS: __________________________________________________________________________________
CITY: ________________________ STATE: _____________ ZIP: _______________________________________
TELEPHONE: (Day) ______________________________________________________________________
(Night) _____________________________________________________________________
SERIAL#: ___________________________________________________________________________________
MODEL#: ___________________________________________________________________________________
PURCHASE DATE: ___________________________________________________________________________
PLACE OF PURCHASE: _______________________________________________________________________
PART # DESCRIPTION QTY
“YOUR ORDER WILL BE PROCESSED WITHIN 3 BUSINESS DAYS”
This form can also be faxed to #: 626-810-2166
31
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project