- Computers & electronics
- Computer components
- Interface components
- Interface hubs
- MuxLab
- DisplayPort 1.2a 1x2 Hub, MST
- Operation manual
advertisement
Specifications
Environment
Devices
Transmission
Video Bandwidth
Signals
Transport
Resolution
HDCP
Audio
Connectors
Cabling Requirement
LEDs
Power Supply
Temperature
Humidity
Enclosure
Dimensions
Weight
Compliance
Warranty
Order Information
DisplayPort 1.2a
Installation of DisplayPort or Mini DisplayPort output source equipment with DisplayPort input monitors
Transparent to the user.
21.6 Gbps (5.4Gbps per lane)
DisplayPort 1.2a & Dual mode DisplayPort protocol
Supports Multi-Stream Transport (MST) of up to eight streams
Up to 3840 X 2160 @ 60 FPS
Revision 1.4 compliant.
LPCM 7.1CH, Dolby TrueHD and DTS-HD Master Audio
DisplayPort receptacle.
Input port : 1x Standard DisplayPort Cable
Output port : 2x Standard DisplayPort Cables
(Select appropriate cable length for video resolution selected)
Input & Output Link: Blue
One (1) 110-240V/5VDC , 2A power supply
Operating: 0° to 40°C (32° to 104°F)
Storage: -20° to 60°C (-4° to 185°F)
Maximum 90% (non-condensing)
Black metal enclosure
4.33” x 2.95” x 1.00” (110 mm x 75 mm x 25 mm)
0.55lbs (250g)
Regulatory: FCC, CE, RoHS
2 years
500506 DisplayPort 1.2a 1x2 Hub, MST
8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5
Tel: (514) 905-0588 Fax: (514) 905-0589
Toll Free (North America): (877) 689-5228
E-mail: [email protected] URL: www.muxlab.com
© MuxLab Inc. 2016 94-000848-A SE-000848-A
DisplayPort 1.2a 1x2 Hub, MST (500506)
Quick Installation Guide
Overview
The DisplayPort 1.2a 1×2 Hub, MST (500506) is a device that allows you to extend different DisplayPort 1.2a content from one DisplayPort connector to two monitors. The hub supports up to 4K (3840 X 2160) video and HD audio, and supports Multi-Stream Transport (MST) of up to eight streams. The hub is HDCP
1.4 compliant and features LED diagnostics. Applications include; commercial and residential AV systems, classroom projector systems, digital signage, boardroom systems, collaborative PC systems, medical information systems.
Pre-Installation Check
Identify the connectors as indicated on the product diagram above. LEDs are located on the front and rear of the unit, next to each connector to indicate traffic.
Installation
In order to install the DisplayPort 1.2a 1x2 Hub, MST, please follow the steps below:
1.
Connect the DisplayPort video source to the input DisplayPort connector of the hub with an appropriate DisplayPort cable, while respecting DisplayPort cable length standards.
2.
Connect the DisplayPort display equipment to the output DisplayPort connectors of the hub with appropriate DisplayPort cables, while respecting
DisplayPort cable length standards.
3.
Connect the 5 VDC power supply to the hub first, and then plug the power supply into an AC power outlet.
4.
Power on the DisplayPort equipment and verify the image quality.
5.
The following diagram shows the final configuration.
Troubleshooting
The following table describes some of the symptoms, probable causes and possible solutions in regard to the installation of the DisplayPort 1.2a 1x2 Hub, MST. If you still cannot diagnose the problem, please call MuxLab Customer Technical Support at 877-689-5228
(toll-free in North America) or (+1) 514-905-0588 (International).
Picture/
Sound
No Image
No Image
Probable Cause
Power
DisplayPort
Cable Wiring
Possible Solution
Check Power Supply connection
Check cable continuity
Check for correct wiring
Check for damaged cable
No Image Synchronization Power off the source and displays, then power them back on.
Flickering Image Synchronization Check DisplayPort cable length against industry standards.
Choppy Sound Synchronization Check DisplayPort cable length against industry standards.
Noise in image Weak signal Check DisplayPort cable length against industry standards.
© MuxLab Inc. 2016
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project