HIT Welding 802030 80 Amp 120-Volt TIG / Stick Welder Assembly & Operating Instructions
Add to My manuals16 Pages
advertisement
PSTICK80
Stick Welder with TIG Option
Assembly & Operating Instructions
READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT.
This manual provides important information on proper operation & maintenance. Every effort has been made to ensure the accuracy of this manual. These instructions are not meant to cover every possible condition and situation that may occur. We reserve the right to change this product at any time without prior notice.
IF THERE IS ANY QUESTION ABOUT A CONDITION BEING SAFE OR UNSAFE, DO NOT
OPERATE THIS PRODUCT!
HAVE QUESTIONS OR PROBLEMS? DO NOT RETURN THIS PRODUCT TO THE RETAILER -
CONTACT CUSTOMER SERVICE.
If you experience a problem or need parts for this product, visit our website http://www.buffalotools.com or call our customer help line at 1-888-287-6981 Monday-Friday, 8 AM - 4 PM Central Time.
A copy of the sales receipt is required.
FOR CONSUMER USE ONLY – NOT FOR PROFESSIONAL USE.
KEEP THIS MANUAL, SALES RECEIPT & APPLICABLE WARRANTY FOR FUTURE REFERENCE.
CALIFORNIA PROPOSITION 65 WARNING : This product m ay contain chem icals, including lead, know n to the S tate of C alifornia to cause cancer and birth defects or other reproductive harm . W ash hands after handling.
PAGE 1
PSTICK80 FEATURES
The Stick Welder is a DC only inverter stick welder with a smooth stick welding performance. It is intended for use for welding steel, stainless steel, cast iron and hard surfacing using electrodes from 1/16 inch to 3/32 inch. This unit can also perform lift start DC TIG welding on steel and stainless steel materials with the optional TIG Torch. (Argon shielding gas along with a regulator, gas hose, and TIG filler rod would also be required for TIG welding.) The removable quick connect weld cables allow for easy connection, tear down, and polarity changes. It is designed to weld mild steel and alloys with electrodes up to 3/32" on materials up to 1/8" thick.
Stick welding gives the operator the flexibility to use this welder for mobile applications, including outdoor applications. Stick electrodes contain a flux, making welding easy and does not require the use of a separate shielding gas which can be blown away by the wind in outdoor applications. Since this welder does not use shielding gas, the operator will not require to have or maintain shielding gas bottles, a regulator or gas hose.
TIG welding does require the use of Argon shielding gas. The shielding gas replaces the flux that is used in stick welding, providing a more controlled and cosmetic weld. However, TIG welding is limited to areas inside or where wind can be controlled, preventing the shielding gas from blowing away.
Use on a 20 amp 115V AC circuit without the use of an extension cord. If an extension cord is necessary for your application, use the appropriate size and length of extension cord to handle 20 amps the entire length of the extension. Talk with a qualified electrician for cord size recommendations.
TECHNICAL SPECIFICATIONS
PAGE 2
Item
Power Supply
No-Load Voltage
Output Range
Duty Cycle
Suggested Electrode
Electrode Diameter
Dimensions
Weight
Description
120V, 25A, 60 HZ, Single Phase
76 Volts DC
20 - 80 Amp DC, 90 Amp DC Peak
20% @ 80A
E6013, E7014, E7018, Stainless Steel
1/16in, 5/64in, 3/32in
12" x 5" x 9"
9.9 lbs.
GENERAL SAFETY RULES
SAVE THESE INSTRUCTIONS
Read and understand all instructions. Failure to follow all instructions listed below may result in serious injury.
Do not allow persons to operate or assemble this STICK WELDER until they have read this manual and have developed a thorough understanding of how the STICK WELDER works.
The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions or situations that could occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
IMPORTANT SAFETY CONSIDERATIONS
1.1
Your Welding Environment
- Keep the environment you will be welding in free from flammable materials.
- Always keep a fire extinguisher accessible to your welding environment.
- Always have a qualified person install and operate this equipment.
- Make sure the area is clean, dry and ventilated. Do not operate the welder in humid, wet or poorly ventilated areas.
- Always have your welder maintained by a qualified technician in accordance with local, state and national codes.
- Always be aware of your work environment. Be sure to keep other people, especially children, away from you while welding.
- Keep harmful arc rays shielded from the view of others.
- Mount the welder on a secure bench or cart that will keep the welder secure and prevent it from tipping over or falling.
1.2 Your Welder’s Condition
- Check ground cable, power cord and welding cable to be sure the insulation is not damaged. Always replace or repair damaged components before using the welder.
- Check all components to ensure they are clean and in good operating condition before use.
PAGE 3
1.3 Use of Your Welder
Do not operate the welder if the output cable, electrode, torch, wire or wire feed system is wet. Do not immerse them in water. These components and the welder must be completely dry before use.
- Follow the instructions in this manual.
- Keep welder in the off position when not in use.
- Connect ground lead as close to the area being welded as possible to ensure a good ground.
- Do not allow any body part to come in contact with the welding wire if you are in contact with the material being welded, ground or electrode from another welder.
- Do not weld if you are in an awkward position. Always have a secure stance while welding to prevent accidents. Wear a safety harness if working above ground.
- Do not drape cables over or around your body.
- Wear a full coverage helmet with appropriate shade (see ANSI Z87.1 safety standard) and safety glasses while welding.
- Wear proper gloves and protective clothing to prevent your skin from being exposed to hot metals, UV and
IR rays.
- Do not overuse or overheat your welder. Allow proper cooling time between duty cycles.
- Keep hands and fingers away from moving parts and stay away from the drive rolls.
- Do not point torch at any body part of yourself or anyone else.
- Always use this welder in the rated duty cycle to prevent excessive heat and failure.
1.4
Specific Areas of Danger, Caution or Warning
Electrical Shock
Electric arc welders can produce a shock that can cause injury or death. Touching electrically live parts can cause fatal shocks and severe burns. While welding, all metal components connected to the wire are electrically hot. Poor ground connections are a hazard, so secure the ground lead before welding.
- Wear dry protective apparel: coat, shirt, gloves and insulated footwear.
- Insulate yourself from the work piece. Avoid contacting the work piece or ground.
- Do not attempt to repair or maintain the welder while the power is on.
- Inspect all cables and cords for any exposed wire and replace immediately if found.
- Use only recommended replacement cables and cords.
- Always attach ground clamp to the work piece or work table as close to the weld area as possible.
- Do not touch the welding wire and the ground or grounded work piece at the same time.
- Do not use a welder to thaw frozen pipes.
PAGE 4
Fumes and Gases
-Fumes emitted from the welding process displace clean air and can result in injury or death.
-Do not breathe in fumes emitted by the welding process. Make sure your breathing air is clean and safe.
-Work only in a well-ventilated area or use a ventilation device to remove welding fumes from the environment where you will be working.
-Do not weld on coated materials (galvanized, cadmium plated or containing zinc, mercury or barium). They will emit harmful fumes that are dangerous to breathe. If necessary use a ventilator, respirator with air supply or remove the coating from the material in the weld area.
-The fumes emitted from some metals when heated are extremely toxic. Refer to the material safety data sheet for the manufacturer’s instructions.
-Do not weld near materials that will emit toxic fumes when heated. Vapors from cleaners, sprays and degreasers can be highly toxic when heated.
UV and IR Arc Rays
The welding arc produces ultraviolet (UV) and infrared (IR) rays that can cause injury to your eyes and skin. Do not look at the welding arc without proper eye protection.
-Always use a helmet that covers your full face from the neck to top of head and to the back of each ear.
-Use a lens that meets ANSI standards and safety glasses.
-Cover all bare skin areas exposed to the arc with protective clothing and shoes. Flame-retardant cloth or leather shirts, coats, pants or coveralls are available for protection.
-Use screens or other barriers to protect other people from the arc rays emitted from your welding.
-Warn people in your welding area when you are going to strike an arc so they can protect themselves.
Fire Hazards
Do not weld on containers or pipes that contain or have had flammable, gaseous or liquid combustibles in them. Welding creates sparks and heat that can ignite flammable and explosive materials.
-Do not operate any electric arc welder in areas where flammable or explosive materials are present.
-Remove all flammable materials within 35 feet of the welding arc. If removal is not possible, tightly cover them with fireproof covers.
-Take precautions to ensure that flying sparks do not cause fires or explosions in hidden areas, cracks or areas you cannot see.
-Keep a fire extinguisher close in the case of fire.
-Wear garments that are oil-free with no pockets or cuffs that will collect sparks.
-Do not have on your person any items that are combustible, such as lighters or matches.
PAGE 5
-Keep work lead connected as close to the weld area as possible to prevent any unknown, unintended paths of electrical current from causing electrical shock and fire hazards.
-To prevent any unintended arcs, cut wire back to ¼ " stick out after welding.
Hot Materials
Welded materials are hot and can cause severe burns if handled improperly.
-Do not touch welded materials with bare hands.
-Do not touch MIG gun nozzle after welding until it has had time to cool down.
Sparks/Flying Debris
Welding creates hot sparks that can cause injury. Chipping slag off welds creates flying debris.
-Wear protective apparel at all times: ANSI-approved safety glasses or shield, welder’s hat and ear plugs to keep sparks out of ears and hair.
Electromagnetic Field
-Electromagnetic fields can interfere with various electrical and electronic devices such as pacemakers.
-Consult your doctor before using any electric arc welder or cutting device
-Keep people with pacemakers away from your welding area when welding.
-Do not wrap cable around your body while welding.
-Wrap MIG gun and ground cable together whenever possible.
-Keep MIG gun and ground cables on the same side of your body.
PAGE 6
Shielding Gas Cylinders Can Explode
High pressure cylinders can explode if damaged, so treat them carefully.
-Never expose cylinders to high heat, sparks, open flames, mechanical shocks or arcs.
-Do not touch cylinder with MIG gun.
-Do not weld on the cylinder
-Always secure cylinder upright to a cart or stationary object.
-Keep cylinders away from welding or electrical circuits.
-Use the proper regulators, gas hose and fittings for the specific application.
-Do not look into the valve when opening it.
-Use protective cylinder cap whenever possible
1.5 Proper Care, Maintenance and Repair
- Always have power disconnected when working on internal components.
- Do not touch or handle PC board without being properly grounded with a wrist strap. Put PC board in static proof bag to move or ship.
- Do not put hands or fingers near moving parts such as drive rolls of fan
USE AND CARE
Do not modify the welder in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the equipment. There are specific applications for which the welder was designed.
Always check of damaged or worn out parts before using the welder. Broken parts will affect the operation. Replace or repair damaged or worn parts immediately.
Store idle welder. When not in use, store it in a secure place out of the reach of children. Inspect it for good working condition prior to storage and before re-use.
The Power Indicator Light is on when the machine is turned on.
Thermal Protection Indicator Light
When the thermal overload indicator is on, it indicates the machine has exceeded the allowable internal temperature. The machine automatically turns off welding output but the fan will remain on to cool down the internal components. When the internal temperature had decreased, the machine will automatically turn welding output back on.
PAGE 7
Current Adjustment
Current adjustment is on the front panel of the machine. It has infinite current output adjustment from 20 to
75 Amps.
Positive Output Connector
This is the connector for the electrode holder and cable, most often, when STICK welding. When this machine is used for TIG welding, this connector is for the grounding cable.
Negative Output Connector
This is the connector for the ground cable and clamp, most often, when STICK welding. When this machine is used for TIG welding, this connector is for the TIG torch.
Ground Cable and Clamp
The ground cable and clamp are attached to the work piece to complete the circuit allowing the flow of current needed to weld.
Welding Cable and Electrode Holder
One end of the cable is connected to the output connectors of the welder. The electrode is held in the electrode holder for welding.
Power Cord
The power cord connects the welder to the 120V volt power supply. Plug the 15 amp plug into a
115V/20Amp receptacle to supply power to the welder.
INSTALLATION
1. POWER REQUIREMENT - AC single phase 120V (110-120V), 60 HZ with a 20 amp circuit breaker is required. DO NOT OPERATE THIS UNIT if the ACTUAL power source voltage is less than 105 volts AC or greater than 132 volts AC.
•
High voltage danger from power source! Consult a qualified electrician for proper installation of receptacle. This welder must be grounded while in use to protect the operator from electrical shock.
• Do not remove grounding prong or alter the plug in any way. Do not use any adapters between the welder's power cord and the power source receptacle. Make sure the
POWER switch is OFF when connecting your welder's power cord to a properly grounded
120 VAC, 60 HZ, Single Phase, 20 Amp input power supply.
2. EXTENSION CORD - We do not recommend an extension cord because of the voltage drop they produce. This drop in voltage can affect the performance of the welder. If you need to use an extension cord, we recommend you check with a qualified electrician and your local electrical codes for your specific area. Do not use an extension cord over 25 ft. in length.
PAGE 8
3. INSTALLATION OF OPTIONAL TIG TORCH
3.1 Remove the ground cable and the electrode holder from the weld output connections. Install the ground cable to the Positive (+) weld output connection.
3.2 Secure the ground clamp to the work piece
3.3 Connect a regulator to a bottle of ARGON gas. Then connect the gas connection from the TIG torch to the regulator.
3.4 Connect the TIG torch weld cable to the Negative (-) weld output connection.
3.5 Set desired amperage on the amperage control knob on the front panel of the welder.
3.6 Turn on the input power switch on the welder.
Be aware that the TIG torch will be electrically HOT when the Input Power Switch on the welder is turned on.
3.7 Turn on the regulator on the bottle of shielding gas and adjust the regulator to approximately 20 CFH.
Then open the shielding gas valve on the torch to start the flow of shielding gas.
EXPOSURE TO A WELDING ARC IS EXTREMELY HARMFUL TO THE EYES AND SKIN!
Prolonged exposure to the welding arc can cause blindness and burns. Never strike an arc or begin welding until you are adequately protected. Wear flame-proof welding gloves, a heavy long sleeved shirt, trousers without cuffs, high topped shoes, and an ANSI approved welding helmet.
3.8 Touch the tungsten that is installed in the TIG torch, to the work piece and quickly pull away approximately 1/4" to create an arc.
OPERATION
High voltage danger from power source! Consult a qualified electrician for proper installation of receptacle at the power source. This welder must be grounded while in use to protect the operator from electrical shock. If you are not sure if your outlet is properly grounded, have it checked by a qualified electrician. Do not cut off the grounding prong or alter the plug in any way and do not use any adapter between the welder's power cord and the power source receptacle. Make sure the POWER switch is OFF then connect your welder's power cord to a properly grounded 120 VAC, 60 HZ, single phase, 20 amp power source.
PAGE 9
4. SETTING UP THE WORK PIECE
Connection between Welder and Power Supply. Connect the power supply cable at the back board of the welder into the single phase 120 voltage power network with breaker; (380 voltage power sources is strictly prohibited to the welder which will severely damage the welder)
4.
4.1 Welding positions
There are two basic positions, for welding: Flat and Horizontal. Flat welding is generally easier, faster, and allows for better penetration. If possible, the work piece should be positioned so that the bead will run on a flat surface.
4.2 Preparing the Joint
Before welding, the surface of work piece needs to be free of dirt, rust, scale, oil or paint or it will create brittle and porous welds. If the base metal pieces to be joined are thick or heavy, it may be necessary to bevel the edges with a metal grinder, the correct bevel should be around 60 degree. See following picture:
PAGE 10
Based on different welding position, there are different welding joint, see following image:
5. GROUND CLAMP CONNECTION
Clear any dirt, rust, scale, oil or paint on the ground clamp. Make certain you have a good solid ground connection. A poor connection at the ground clamp will waste power and heat. Make sure the ground clamp touches the metal.
6. ELECTRODE
The welding electrode is a rod coated with a layer of flux. When welding, electrical current flows between the electrode (rod) and the grounded metal work piece. The intense heat of the arc between the rod and the grounded metal melts the electrode and the flux. For best performance on this unit, we suggest the use of
6013 electrodes.
7. SELECTING THE PROPER ELECTRODE
There is no golden rule that determine the exact rod or heat setting required for every situation. The type and thickness of metal and the position of the work piece determine the electrode type and the amount of heat needed in the welding process. Heavier and thicker metals required more amperage. It is best to practice your welds on scrap metal which matches the metal you intend to work with to determine correct heat setting and electrode choice. See the following helpful trouble shooting tips to determine if you are using a correct electrode.
7.1. When proper rod is used:
7.1.a. The bead will lay smoothly over the work without ragged edges
7.1.b. The base metal puddle will be as deep as the bead that rises above it
7.1.c. The welding operation will make a crackling sound similar to the sound of eggs frying
7.2. When a rod too small is used;
7.2. a. The bead will be high and irregular
7.2. b. The arc will be difficult to maintain
7.3. When the rod is too large
7.3. a. The arc will burn through light metals
7.3. b. The bead will undercut the work
7.3. c. The bead will be flat and porous
7.3. d. Rod may be freeze or stick to work piece
Note: Rate of travel over the work also affects the weld. To ensure proper penetration and enough deposit of rod, the arc must be moved slowly and evenly along the weld seam.
PAGE 11
8. SETTING THE AMPERAGE CONTROL
The welder has an infinite current control. It is capable of welding with electrodes up to 3/32” diameter. There is no golden rule that determines the exact amperage required for every situation. It is best to practice your welds on scrap metal which matches the metals you intend to work with to determine correct setting for your job. The electrode type and the thickness of the work piece metal determine the amount of heat needed in the welding process. Heavier and thicker metals require more voltage (amperage), whereas lighter and thinner metals require less voltage (amperage).
Consult the welding electrode packaging for recommended welding amperage range.
9. WELDING TECHNIQUES
The best way to teach yourself how to weld is with short periods of practice at regular intervals. All practice welds should be done on scrap metal that can be discarded. Do not attempt to make any repairs on valuable equipment until you have satisfied yourself that your practice welds are of good appearance and free of slag or gas inclusions.
9.1 Holding the electrode
The best way to grip the electrode holder is the way that feels most comfortable to you. Position the Electrode to the work piece when striking the initial arc it may be necessary to hold the electrode perpendicular to the work piece. Once the arc is started the angle of the electrode in relation to the work piece should be between
10 and 30 degrees. This will allow for good penetration, with minimal spatter.
9.2 Striking the arc
EXPOSURE TO A WELDING ARC IS EXTREMELY HARMFUL TO THE EYES AND SKIN!
Prolonged exposure to the welding arc can cause blindness and burns. Never strike an arc or begin welding until you are adequately protected. Wear flame-proof welding gloves, a heavy long sleeved shirt, trousers without cuffs, high topped shoes, and an ANSI approved welding helmet.
Scratch the work piece with the end of electrode to start arc and then raise it quickly about 1/8 inch gap between the rod and the work piece, see following picture
It is important that the gap be maintained during the welding process and it should be neither too wide or too narrow. If too narrow, the rod will stick to the work piece. If too wide, the arc will be extinguished. It needs much practice to maintain the gap. The beginners may usually get sticker or arc extinguishing. When the rod is stuck to the work piece, gently rock it back and forth to make them separate. If not, a short circuit will occur and it will break the welder.
PAGE 12
A good arc is accompanied by a crisp, cracking sound. The sound is similar to that made by eggs frying. To lay a weld bead, only 2 movements are required; downward (as the electrode is consumed) and in the direction the weld is to be laid, as in following figure:
9.3 Types of weld bead
The following paragraphs discuss the most commonly used arc welding beads. The stringer bead Formed by traveling with the electrode in a straight line while keeping the electrode centered over the weld joint.
Stringer Bead Weave Bead
The weave bead Used when you want to deposit metal over a wider space than would be possible with a stringer bead. It is made by weaving from side to side while moving with the electrode. It is best to hesitate momentarily at each side before weaving back the other way.
9.4 Welding position
Flat position It is easiest of the welding positions and is most commonly used. It is best if you can weld in the flat position if at all possible as good results are easier to achieve.
Flat Position Horizontal Position
The horizontal position it is performed very much the same as the flat weld except that the angle is different such that the electrode, and therefore the arc force, is directed more toward the metal above the weld joint.
This more direct angle helps prevent the weld puddle from running downward while still allowing slow enough travel speed to achieve good penetration. A good starting point for your electrode angle is about 30 degrees
DOWN from being perpendicular to the work piece.
PAGE 13
9.5 Judge the good weld bead
When the trick of establishing and holding an arc has been learned, the next step is learning how to run a good bead. The first attempts in practice will probably fall short of acceptable weld beads. Too long of an arc will be held or the travel speed will vary from slow to fast (see following)
A. A. Weld speed is too fast.
B. B. Weld speed is too slow.
C. C. Arc is too long.
D. D. Ideal weld.
A solid weld bead requires that the electrode be moved slowly and steadily along the weld seam. Moving the electrode rapidly or erratically will prevent proper fusion or create a lumpy, uneven bead.
ELECTRIC SHOCK CAN KILL! To prevent ELECTRIC SHOCK, do not perform any welding while standing, kneeling, or lying directly on the grounded workpiece.
9.6 Finish the bead
As the coating on the outside of the electrode burns off, it forms an envelope of protective gases around the weld. This prevents air from reaching the molten metal and creating an undesirable chemical reaction. The burning coating, however, forms slag. The slag formation appears as an accumulation of dirty metal scale on the finished weld. Slag should be removed by using a chipping hammer.
PEENING THE SLAG FROM A WELD JOINT CAUSES SMALL CHIPS OF METAL TO FLY
THROUGH THE AIR! Metallic chips flying through the air can cause eye injury or injury to other parts of the head, hands or exposed portions of the body. Wear goggles or safety glasses with side shields and protect the hands and other exposed parts of the body with protective garments, or if possible, work with a shield between the body and the work piece.
The intense heat produced at the arc sets up strains in the metal joined by welding. Peening the weld not only removes the scale left behind in the welding but relieves the internal strains developed by the heating and cooling process.
MAINTENANCE
•
Maintain your welder. Keep the welder in good repair by adopting a program of conscientious repair and maintenance. Have necessary repairs made by qualified service personnel.
• Periodically clean dust, dirt, grease, etc. from your welder.
• Every six months, or as necessary, remove the cover panel from the welder and air-blow any dust and dirt that may have accumulated inside the welder.
• Replace power cord, ground cable, ground clamp, or electrode assembly when damaged.
PAGE 14
TROUBLESHOOTING
SYMPTOM
Unit Does Not Power Up
Can Not Create An Arc
Overload Indicator Is On
Electrode Holder or ground cable getting hot. Output Connections Getting Hot.
Poor Welding Performance, excessive spatter
Electrode Sticks
POSSIBLE CAUSE
Unit Is Not Plugged In
Input Power Circuit Breaker Not On
The Main Power Switch Is Not Working
Work Piece is Painted Or Rusty
Ground Clamp Is Connected Where There Is
Paint Or Rust
Clamp Is Not Electrically
CORRECTIVE ACTION
Plug In Unit
Reset Input Power Circuit Breaker
Replace Main Power Switch
Remove All Paint And Rust
Remove All Paint And Rust So Ground
Clamp Is Connected To Bare Metal
Make Certain The Ground Clamp Is Ground
Connected To The Work Piece Connected To The Work Piece
Amperage Too Low for Electrode Consult the electrode packaging for correct amperage settings.
The internal temperature is too high.
Leave power on and let the fan cool the unit.
Output will continue when the unit has cooled.
Weld Cable Connections Loose Check to make certain weld cables are tight.
Weld Cable Connections have corroded.
Clean weld connections and reinstall.
Damp Electrode Use fresh and dry electrodes.
The electrode is kept in contact with the work piece for too long while striking an arc.
This will take practice. Keep trying.
The welding travel speed is too fast Reduce the welding travel speed. Maybe incorporate a slight weave over the joint.
The welding travel speed is to slow Increase the welding travel speed.
Welding Bead Is Too Thin
Welding Bead Is Too Thick
PARTS DIAGRAM
PAGE 15
PARTS LIST
No. Part Number Description Reference
1 2.05.08.031
2 1.1.01.01.1006
3 1.1.05.02.0558
4 2.03.30.1235
5 2.03.30.1219
6 2.03.30.1217
7 2.05.05.961
8 1.2.08.02.2108
9 1.2.08.01.0518
10 2.07.11.016
11 1.1.01.05.2999
12 2.07.28.041
13 1.1.01.04.1354
14 2.07.43.924
15 2.07.33.629
16 2.07.43.925
17 2.05.02.458
18 1.1.12.18.0002
19 2.05.05.962
20 2.07.80.211
21 1.1.11.18.0090
201604
Handle Black 155*42*27
Encloser
Main control board
PSTICK160KE.2
POWERSTICK 80KE (V1.3)
STICK-TIG toggle switch BLUEARC 90 STI
Potentiometer wiring harness POWER STICK 80KE (V1.0)
Indicator light wiring harness POWER STICK 80KE (V1.0)
Front panel
"-" output cable
"+" output cable
Potentiometer knob
Front panel mounting
Fast recovery diode
Bottom
EXTM100-3 ABS 5VA
CARIARC 80
ST80i
KDJII23-16-6J
PSTICK200KE.1-1
D92-02 20A/200V
PSTICK160KE.3-2
Fast recovery diode heat sink HG2ZX7200KE.2-5
Single tube IGBT
IGBT heat sink
RJH60F5DPK
HG2ZX7200KE.2-3
Supporter
Fan wiring harness
HG2ZX7200KE.2-1
POWER STICK 80KE (V1.0)
Back panel
Rocker switch
Power cord
EXTM100-5 ABS 5VA
R220-1C2N-BBZ-NN 16A/250V
BLUEARC 90STI(POWER STICK 80KE)
Qty
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
4
1
PAGE 16
advertisement
Related manuals
advertisement