Graco 17G181 Magnum ProX21 Stand Airless Paint Sprayer Instructions / Assembly

 & MAGNUM
PRO QUICK GUIDE
KNOW YOUR CONTROLS
Read Owner's Manual for complete instructions and warnings. This
quick guide is not a substitute for reading and understanding all
instruction manuals and warning labels supplied with the equip-
ment, Manuals are available at magnum.graco.com
Follow pressure relief procedure and wear protective
equipment including but not limited to protective eye wear.
SKIN INJECTION HAZARD: Keep clear of spray tip and leaks.
Engage trigger lock when not spraying.
FIRE AND EXPLOSION HAZARD:
Follow fire and explosion warnings as listed in your manual.
READ AND UNDERSTAND ALL LABELS AND INSTRUCTION
MANUALS BEFORE USE. FAILURE TO FOLLOW ALL WARNINGS
CAN RESULT IN SERIOUS INJURY, AMPUTATION, OR DEATH.
OPE
If needed, connect
hose to gun. Remove
red cap, then connect
hose to sprayer. Tighten
securely.
Engage Trigger Lock.
Assure Spray Tip is
properly inserted into
the Spray Tip Guard,
and the Spray Tip Guard
| assembly is tightened
№ securely to gun.
3 Turn the [=] - [=]
Pressure
Control Knob
to the lowest [=]
setting.
magnum.graco.com/quickassembly
Turn Power
Switch OFF and
plug sprayer into a
grounded outlet.
magnum.graco pe
Separate Drain Tube (smaller)
from Suction Tube (larger). Place
Drain Tube in a waste pail. Submerge
Suction Tube into pail filled with water
for water-based material, or mineral
spirits if spraying oil-based material.
Turn the Prime/Spray Valve
to the PRIME position. Press
to loosen inlet valve ball. Turn
— Pressure Control Knob to START
position. Turn Power Switch ON.
Allow fluid to flow up
the Suction Tube and
out of Drain Tube for 30-60
seconds. Turn Power
Switch OFF.
START UP
Submerge Suction
Tube into paint. Turn
Power Switch ON and
watch for paint to come
out of the Drain Tube. Turn
Power Switch OFF.
Rotate Spray Tip to
UNCLOG Position.
Disengage Trigger Lock.
Point gun into waste pail,
pull and hold trigger. Turn
the Prime/Spray Valve to
SPRAY position and turn
Power Switch ON.
When paint comes out of gun,
release trigger. Engage Trigger
Lock. Transfer Drain Tube to paint pail
and attach to Suction Tube. Rotate
Spray Tip back to SPRAY position
and ensure Spray Tip Guard is tight.
YOU ARE NOW READY TO SPRAY!
SPRAYING
7
magnum .graco.com/
howtospray
Turn Pressure Control Knob to the START
position. Disengage the Trigger Lock.
J/ Good Spray Pattern
—
12 in. (30 em)
from surface
(Q) rans- caps at edges
———
р
ns
Pressure
too low
Tip Wear
Pull trigger after
starting stroke.
Aim Gun here
to overlap
stroke by 50%
Release trigger
before end
Increase Pressure Control Knob
if needed until spray is even and
without gaps at edges.
CLEANUP i REVERSIBLE
Garden hose cleanup for water-based paints only.
See Owners Manual for pail cleanup or oil-based materials. . © № RAY TI E ©
Turn Power Switch OFF. graco
Place Suction and Drain
Tubes in waste pail. Turn
4
: Your sprayer is shipped with a Spray Tip to spray paint. If
ee TO you are spraying stain see the store associate to purchase a
Prime/Spray Valve to PRIME. brush. Remove gun filter and smaller Spray Tip size.
um Pressure “onto NON clean. Reassemble gun filter, .
to START position. Trigger Sprav Tip and Sprav Ti rd If your sprayer stops spraying, you most likely have a Spray
gun into a waste pail. pray “Ip anc Spray “Ip gare, Tip clog. Engage Trigger Lock and reverse the Spray Tip to
AG = the UNCLOG position. Disengage Trigger Lock and spray into
a waste area to remove the clog. Engage Trigger Lock and
Engage Trigger Lock. Porform CLEANUP. before STORAGE. return the Spray Tip to SPRAY position. See Owner's Manual
Storage/Priming Tool not available with all models, see Owner's Manual.
Remove Spray Tip Guard
assembly from gun and
place in waste pail.
for more information.
Remove Pump
Armor" bottle cap a SPRAY == UNCLOG
and foil seal. If needed,
Ñ \ magnum. graco.com/rac
STORAGE/PRIMING TOOL
from Suction Tube.
Not available with all models, see Owner's Manual.
Screw Power Flush™ Valve (included
with sprayer) to a garden hose. Turn
on water. Open Power Flush Valve.
Rinse paint off Suction and Drain Tubes,
inlet screen and Spray Tip and Spray
Tip Guard. Close Power Flush Valve,
Unscrew inlet screen and
place in waste pail. Thread
Power Flush Valve to Suction Tube.
Open Power Flush Valve. Turn
Power Switch ON and let water run
through Drain Tube for 20 seconds.
Turn Power Switch OFF.
Turn Prime/Spray Valve
to PRIME. Place Drain Tube
in waste pail. Turn Pressure
Control Knob to START position.
Use the Storage/Priming Tool if you are
While holding the Suction experiencing difficulty priming your sprayer.
Tube above the sprayer, |
pour approximately 2 ounces
(60 ml) of Pump Armor into the
Suction Tube and turn
To save paint in hose, Power Switch ON.
disengage Trigger Lock and ;
trigger gun into paint pail, turn When Pump Armor is flushed
Prime/Spray Valve to SPRAY and through the sprayer, turn —
turn Power Switch ON. When Power Switch OFF. Replace See your Storage/Priming
water comes out of gun, keep and tighten child-proof cap Tool Instruction Guide for
gun triggered and aim into waste for storage. information on how to use
pail. Continue to flush until water the Priming/Storage Tool.
runs clear. Screw inlet screen back —
to Suction Tube. Ensure
that spray gun and hose
Turn Pressure
Control Knob to stay attached to sprayer. НЦ ESTIONS?
lowest setting and 888-541-9788
release trigger. Engage Turn the Spray/Prime magnum.graco.com/aplus
Trigger Lock. Turn the valve to SPRAY position A
Prime/Spray Valve to for storage. Turn Power
PRIME and turn Power Switch OFF and unplug SERVICE G a
Switch OFF. sprayer from outlet. JAS510 Revision A, January 2018, Original Instructions. This Quick Guide contains English.
Source Manuals: 3A5507, MM 3A5510. Copyright 2018