wedi US3000005 16 in. x 16 in. Shower Niche Product Brochure

PDF

Document

Shower & Spa

System Solutions

Innovation. System. Quality.

Your local wedi distributor:

US www.wedicorp.com

Bryan Baeumler

“ My reputation is built on quality installations, zero call backs, clean and predictable professional work. My customer‘s depend on my word, that‘s why I rely on wedi waterproof shower systems which offer the only complete, reliable, cost-efficient solution for constructing 100% waterproof and mold proof showers. These systems are easy to install, ready to tile the same day and open up a whole new world of custom design possibilities for showers, wet areas and baths. And to be sure:

I contacted wedi to enjoy their on-site training and certification program.“

Bryan Baeumler

Owner of Baeumler Construction and

Host of HGTV’s “Leave it to Bryan”

Toronto, Canada

100% waterproof – with manufacturer‘s guarantee

Multiple customizable products sizes

Easy and safe modular installation

Natural protection against mold

Fastest Installation of waterproof, custom tiled showers in the industry

Ready to tile upon installation –

Any size or type tile & stone

wedi Shower System Solutions

wedi Waterproof Shower Systems offer reliable, cost-efficient solutions for constructing 100% waterproof and mold proof showers and are easy to install.

 Fundo Primo Shower Kit / Fundo Riolito neo Shower Kit

 Fundo Primo, Shower Base and Accessories

 Fundo Ligno, Barrier Free Shower Base

 Fundo Riolito neo, Shower Base with linear drain

 Shower Base Extensions

 Fundo Riolito Discreto, Tileable vertical drain cover system

wedi Building Panel

wedi Building Panels are the ultimate and complete wet room tile backer board and often used within the range of wedi shower systems as well as on walls, floors, countertops and many more applications.

 Constructing Individual Tileable Furniture

 For Shower, Tub & Steam Room Walls and Ceilings

 Over Wood and Concrete Subfloors –

With or Without Floor Warming Systems

 In Countertops Applications

wedi Prefabricated Modules

wedi Prefabricated Modules open up a whole new world of design possibilities for showers, wet areas and baths.

 Curbs

 Recessed Niches

 Benches and Seats

 Sloped Shower Ramps

Installation Accessories & Tools

wedi Installation Accessories & Tools offer additional products you need for the installation and guarantee maximum safety and easy handling.

 Joint Sealant and Accessories

 Vapor Barrier for Steam Rooms

 Fastener Systems (metal washer, screws)

01 wedi Fundo Primo

The original wedi Fundo: Robust, pre sloped, waterproof, shower floor bases with 4“x 4“ drain cover.

Customizable on site.

02 wedi Fundo Riolito neo /

Riolito neo Modular

Fully factory integrated linear drainage. Models include one-way, two-way and four-way slope designs.

03 wedi Fundo Ligno

Our newest Fundo model: Floor level

3/4“ profile designed especially for suspended wood subfloors. Like all wedi shower bases it is pre sloped, and waterproof. Comes with 4“x 4“ drain cover. Customizable on site.

04 wedi Fundo Discreto

Wall drain module for integration in seats or false walls. Installs over select

Riolito neo linear drain models.

Cover is tileable on one side and polished stainless steel on reverse side.

05 wedi Building Panels

Perfect substrate for practically any wall or floor application.

06 wedi Fundo Primo Drains & Covers

The perfectly easy to use compression fit black PVC drain is always included with a standard Drain

Cover Set.

07 wedi Shower Benches

Prefabricated, slightly sloped bench options or simply built on site to fit using wedi 2“ or 1 1/2“ Building

Panel.

08 wedi Wall Mounted Triangle Seat

Suspended seat solution, equipped with mounting bracket system for installation into existing framing.

09 wedi Niches

The perfect fit for all shower necessities.

10 wedi Curbs

For shower entry design where safe and sound transitions are required.

11 wedi Sloped Shower Ramps

Where wheelchair accessible or ADA compliant entries are required.

12 wedi Shower Base Extension

Extend any wedi shower floor base type using pre-sloped extension modules featuring pre-made connections to any base.

wedi Fundo Primo Kit

Subliner Dry Flexi Collars for pipes and valves

wedi Fundo Shower Kits

 Available as wedi Fundo Primo Kit (point drain) and

Fundo Riolito neo Kit (linear drain)

 Easy to install and blending the traditional values of design flexibility and robustness while offering the added benefits that come with state of the art material and manufacturing technologies

 No more presloping, pan liner cracks or membrane pin holes, clogged drain weepholes and mold growth

 Reducing the traditional installation time and down times for a full shower floor preparation for tiling from 2 – 3 days to now 30 minutes wedi Fundo Primo offers a point drainage shower system wedi Building Panel, the perfect tiling substructure for walls wedi Full Foam Shower

Curb Lean included

The total shower solution

 All you need to build a shower system ready for tile in one

Kit box – selectively with point or linear drain

 Entire System is 100% waterproof and moldproof

 Very low weight, but extremely durable

 For a safe modular installation with option to field modify system components for custom tiled showers

 Installers and builders save time and money and are protected under wedi system warranty covering the entire shower substrate

wedi Fundo Riolito neo Kit

wedi joint sealant, permanently flexible, waterproof and a strong adhesive wedi Niche

(optional)

Subliner Dry Flexi

Collars for pipes and valves wedi Building Panel

Drain unit

9 wedi Fundo Riolito neo linear drain system

(optional cover plate available in three designs) wedi Full Foam Curb Lean

wedi Fundo Primo

The wedi Fundo Primo Shower System features a square drain cover point drainage solution for fast and safe renovation and new construction installations.

Primo is internally waterproof due to its wedi XPS foam‘s closed cell structure and naturally protect against mold or mildew like every wedi XPS foam based product. It is fast and clean to cut to fit custom designs while the level of prefabrication reduces installation time significantly. The shower floor units feature a strong and pre-sloped surface which can be tiled over immediately whether you choose mosaic size or large format tile. Drain unit and drain cover set is always included with each Primo shower floor unit while further optional drain cover designs are available. Pre-sloped extension panels are available so that virtually no limit exists for making any size or shape for custom shower designs happen. The added values offered by Fundo Primo come in the form of many more performance advantages. Naturally, Fundo Primo is insulating keeping surfaces warmer. Especially when compared to traditional mortar bed installations or other currently known methods for building showers such as those including use of sheet – or liquid waterproofing membranes used in an attempt to manage water exposure – wedi Fundo Primo‘s simplicity and high performance shows. The installation combines many manual and separate installation steps and materials usually needed into very few. Fundo Primo adds speed, safety and consistency to your installation: Measure, possibly cut, thinset to subfloor, connect drain – done. The most unique advantage, however, is the complete and natural core waterproofness of the wedi product and its completeness and range of components that will form an entire assembly system with Fundo Primo engineered to fit and last. A true system with full warranty coverage. These added values and its detail perfections eliminate the technical concerns in shower installations. But this is not where wedi shower systems stop offering it’s added values: The wedi Fundo shower system adds to your productivity and enables you to provide real value to your customers: Our wedi Fundo Shower systems reduce the installation time for just the shower floor from a 2 – 3 day process (includes drying times) to only 30 minutes when compared to traditional methods built with pre slope, vinyl liner and final mortar bed. wedi helps you to turn showers into service quicker, cleaner, safer. Especially for our contractors,

Fundo Primo helps to get to setting tile faster and on a much more consistent and tile friendly surface. Customers will appreciate the "no noise and no dirt and dust" installation. The wedi products do not contain harmful ingredients providing peace of mind to contractors and end users.

Exactly uniform predefined gradient

Point Drain Shower Floor Solutions

Advantages for the user save time and money

Huge variety of design, function and format

Caulking nut

Rubber caulking gasket

Drain body wedi Fundo Primo unit

Fiber gasket

Drain to Base Assembly

wedi sealant

Rubber gasket

Locking nut

2“

wedi Fundo Primo Installation*

Before Installation:

 Have extra 2 × 4 blocking installed over bottom plate between studs along to support wedi building panel to shower base transition area.

 Subfloor is stable, even and load-bearing, and meets deflection criteria of maximum L/360 and requirements as per IRC. Wooden or concrete structural substrates are dry and sufficiently load-bearing considering live and dead load. Wood and Steel framing is sufficiently load-bearing, plum and square.

 Floor drain assembly below floor is stabilized, fixed and supported in position, and will not sink under water load.

 Only wedi products (Building Panels, Curb, Joint Sealant and Fasteners) are used for wedi Fundo Shower System assembly.

 Installer has received instructions from wedi technical sales staff or is informed about proper installation methods as described.

 wedi shower bases can be cut to size using a skilsaw. The Z notch channel must be remade and cleaned from sawdust or other possible contamination. It must be at minimum 1/2” wide and 3/8” deep.

01 02

Cut the 2” pipe flush (or max. 1/8“ above) to the floor construction. Make sure that the cut out fits to the Fundo panel drain. Cut out a 5 inch diameter hole around the 2 inch pipe to allow for the wedi drain to be inserted into the subfloor while the cut out area must remain free of deflection. The drain and trap have to be sturdily fastened to the sub floor. Assemble the drain unit follow ing the instruction drawing.

Set up a continuous 1/4” bead of wedi sealant along the top side of the wedi Fundos’ valve groove profile.

Drop the drain body firmly into the sealant.

Turn the Fundo base upside down and apply the rubber and the fiber gasket.

Tighten the gaskets firmly to the bases‘ steel ring using the locking nut. Make sure the drain body is still safely received in the valve-bead of sealant.

07 08

Skim coat the thinset ANSI 118.4 and comb through with a 1/4” × 1/4” notched trowel. Channels pointing to the en trance. Trowel the thinset on the rear side of the Fundo again using a 1/4” × 1/4” notched trowel.

There are different ways to ensure good bond of the wedi base to the subfloor. Required is a setting bed thickness of min. 3/16“ and max. of

5/16“ (compressed). Applying thinset on both, wedi base and subfloor, is a best practice recommended to achieve full surface coverage adhesion.

* Installations in Australia & New Zealand: Please refer to Installation manuals featuring the applicable job site requirements and wedi drains.

Press the Fundo firmly into the thinset bed, ensuring that the installation is level and void free. Apply some weight equally and for at least 30 minutes (thinset bags or tile boxes).

Set up the rubber caulking gasket (with the bevelled side up) around the 2” pipe in the subfloor. The rubber gasket must be flush with the upper end of the 2” ABS or PVC pipe.

Do Not use any Lubricants.

Tighten (squeeze) the rubber caulking gasket firmly with the caulking nut (use a flat headed screwdriver) and finally insert the plastic frame and strainer on top (without adhesive). The frame and strainer will be held in a grout joint only once tiling commences.

Set up a continuous 1/2” bead of wedi Joint Sealant along the pans channel on the outer perimeter and only in areas where you can immediately install a building panel into the fresh sealant.

Push the wedi panel all the way into the channel of the shower base channel and its bead of sealant. Smooth out any pushed out sealant on inside seam using a putty knife. Fasten the panels directly to the studs starting 1 ft above the base and at a rate of 1 fastener per 1ft. One extra fastener is set into the seam to the next panel to create a flush transition.

The seams should be covered 1” on either side of seam. All fastener/ washers are covered with sealant stretching 1” over the washer edges.

15 16 wedi Niches are installed in a cut out in the wedi wall and attached with it‘s flange right into the center of 16 o.c. studs. wedi Joint Sealant is set along the connection of wall to niche. 2 Fasteners each side of the niche are set to create a flush transition to the wall panels. Another 1/2” bead of wedi Joint Seal ant is spread over fasteners and seams.

For the installation to properly work it is critical to waterproof all penetrations of the wedi product such as shower valves and shower heads using the appropriate sealing gaskets for the application. The wedi Mixing Valve Flexi Collar and wedi Flexi Collar (for 1/2” – 3/4” shower pipe protrusions) are used for these applications and are part of the wedi System complete warranty.

17 18

Weight is applied on and against the curb (from outside) and another

1/2” bead of sealant is applied over all curb seams and spread flat. The seams must be covered 1” either side of a seam.

Curb connection notches must be cut to fit select Primo bases with perimeter thickness higher than 1 1/2”.

After Installation

All visible joints or seams in the installation are visibly covered and reinforced with wedi joint sealant applied flat over the seams. Coverage of wedi joint sealant over all seams should be at least 3/4-1 inch on either side of the seam. The joint sealant should be no less than 1/16“ thick for strength. Do not add mesh tape into the wedi joint sealant. This may only put the waterproof performance at risk and will not strengthen the system‘s resistance against movement related stresses. Once wedi joint sealant application over all shower system seams has been completed, a water flood test may be performed as early as 2 hours later. No premixed organic mastic adhesives are used with wedi systems when installed in wet areas. Ceramic tile smaller than 2 x 2“ square may be adhered using a modified thinset mortar and may be grouted using polymer modified cement based grout. Ceramic tiles smaller 1 x 1“ square require adhesion in epoxy thinset mortar and grouting using epoxy grout. Non square tiles must be set accordingly and the shortest side of the tile determines the appropriate setting materials. Pebble Stones may be set and grouted using both, modified cement based thinset mortars and grouts or epoxy thinset mortar and grout, or a combination. Larger format tile > 4 inches square may be used on wedi Fundo. They have to be cut for their grout joints aligning with the wedi shower base slope lines (where slope fields meet).

wedi Drain Cover Assembly / Insertion

Insert Cover frame into base hole (no glue / no screws). You may caulk between part and tile to create a flexible grout joint. The optional Extension Collar can be cut to height if part is needed. The caulk joint must not create a water barrier damming up the water draining through the thinset bed into the drain from below the tile. Therefore the thinset layer must be continuous toward the drain. Use the black plastic extension collar if you need to raise the wedi frame and cover. Cut extension collar to size and insert below the frame/cover. If not needed, the extension collar may be disposed of as it is not necessary for the functioning of the wedi installation. wedi Cover

Cover frame

Optional Extension Collar

Fundo Primo Shower Kit – Full Shower System in a Box

All products needed to build a wedi shower are included and provide a single manufacturer warranty. Safe transportation in one box, easy estimating of product quantities needed.

wedi Niche (optional) wedi Building Panel wedi Fundo Primo

Shower Base

Subliner Dry

Flexi Collars for pipes and valves

Screws and

Washers wedi Triangle

Corner Seat

(optional) wedi Full Foam

Curb Lean

Drain unit and

Cover Set

Fundo Ligno recessed shower base

Under Floor Tile: wedi Building Panel or Subliner Sheet

Membrane connected and sealed to shower base and wall units

wedi Fundo Ligno

Homeowners and builders increasingly favor shower spaces which can function without a curb or would not require any build up over existing floor areas resulting in a step up into the shower. One important reason for this trend is: easier and safer access to the shower for older and/ or physically disabled persons. While this trend offers great design and business opportunities it also presents technical challenges which cannot be overcome by many conventional shower installation methods or products. Main challenges are safe recessing of a sloped shower base into an existing structural floor for a flush transition and the extension of waterproofing from shower area into surrounding floor areas no longer protected by a curb keeping water inside the shower area. To address all challenges for tile professionals, wedi engineered Fundo Ligno, a sloped shower base ¾ inches thin at its perimeter and available in various sizes. Ligno can be field modified. The installation within a ¾” plywood structure requires no cutting into joists. Load-bearing plywood is simply re-installed between floor joists and over 2 × 6 blocking then attached to the joists. This guarantees a full support and protection of the tiled surface. The wedi typical strong cement based, reinforced surface is pre-sloped, directly tileable with large or small format tile. Ligno interlocks with wedi Building Panel used as waterproof backer board on walls as well as on the surrounding floor. Optionally, wedi‘s Subliner Dry Sheet Waterproofing membrane can be used. Both options offer a complete and professional system installation. wedi Fundo Ligno is designed to provide for a low profile base thickness of only 3/4”. This allows for a fast and flush installation into a subfloor assembly without cutting into floor joists. The system is designed to work without a curb. Enjoy the ease of installation without creating a structural hazard because you maintain the structural subfloor panels installed between floor joists under the wedi Fundo Ligno. Because barrier free showers may be exposed to heavy point loads (e.g. wheel chair), you can confidently rely on the structural strength of the wedi base and subfloor as well as the wedi Fundo's traditional strong cement based surface for ideal tile bond using any suitable cement based tile adhesives or grouts. As applied to all wedi Fundo Shower Systems, wedi Fundo Ligno is designed to interlock and work with wedi Building Panels, wedi Joint Sealant, wedi Fasteners, wedi Seats and Benches, wedi Niches and many more accessories, that truly complete your shower installation and waterproofing system. The installation is fast, modular but customizable, and covered by wedi's full system warranty.

Can be combined with all Fundo drains

Point Drain Shower Floor Solutions

Decoupling effect

Especially for timber joist floors

Caulking nut

Rubber caulking gasket

Drain body wedi Fundo Ligno

Fiber gasket

Drain to Base Assembly

wedi sealant

Rubber gasket

Locking nut

2“

wedi Fundo Ligno Installation*

Before Installation:

 Have extra 2 × 4 blocking installed over bottom plate between studs along to support wedi building panel to shower base transition area.

 After recessing or when system is installed over regular subfloor, subfloor is stable, even and load-bearing, and meets deflection criteria of maximum L/360 and requirements as per IRC. Wooden or concrete structural substrates are dry and sufficiently load-bearing considering live and dead load. Wood and Steel framing is sufficiently load-bearing, plum and square.

 Floor drain assembly below floor is stabilized, fixed and supported in position, and will not sink under water load.

 Only wedi products (Building Panels, Curb, Joint Sealant and Fasteners) are used for wedi Fundo Shower System assembly.

 Installer has received instructions from wedi technical sales staff or is informed about proper installation methods as described.

Cut 3/4” Plywood base out fitting the space of wedi Fundo Ligno. Safely install 2 x 6 blocking along floor joists and in betwen floor joists where the perimeter of the Ligno base will be located, install 2 x 6 blocking

3/4“ below the top of the floor joists. Adjust for thinset thickness under wedi Fundo Ligno base and / or the flooring underlayment installation adjacent to shower area to create a flush transition for waterproofing and tile between floor and shower area. Re-install 3/4” plywood over blocking to have the plywood flush with the floor joists and fill with furring strips on top of floor joists in case the blocking / joist that carry the plywood under wedi base is installed higher than 3/4” deep from top of floor joists. Make sure the entire perimeter of the wedi Fundo Ligno base is supported by floor joists or adequate blocking. Make sure the plywood base shows no seams where close to the cut out for the wedi

Fundo Ligno drain. The cutout around the center of the 2” floor pipe must be 6 1/2” (max 7”) in diameter to allow drain recess and must not create any subfloor deflection. The pipe is cut square and even at 5/8” below the recessed subfloor top surface.

Assemble the drain unit following the instruction drawing.

Set up a continuous 1/4” bead of wedi Joint Sealant along the top side of the wedi Fundos’ valve groove profile.

* Installations in Australia & New Zealand: Please refer to Installation manuals featuring the applicable job site requirements and wedi drains.

Drop the drain body firmly into the sealant.

Turn the Fundo base upside down and apply the rubber and the fiber gasket.

Tighten the gaskets firmly to the bases‘ steel ring using the locking nut. Make sure the drain body is still safely received in the valve-bead of sealant.

Skim coat the thinset ANSI

118.4 and comb through with a 1/4” × 1/4” notched trowel channels pointing to the entrance.

08 09

Trowel the thinset on the rear side of the Fundo again using a 1/4” ×

1/4” notched trowel. There are different ways to ensure good bond of the wedi base to the subfloor. Required is a setting bed thickness of min. 3/16“ and max. of 5/16“ (compressed). Applying thinset on both, wedi base and subfloor, is a best practice recommended to achieve full surface coverage adhesion. Press the wedi Fundo Ligno firmly into the thinset bed, ensuring that the installation is level and void free. Apply some weight equally and for at least 30 minutes (thinset bags).

Set up the rubber caulking gasket (with the bevelled side up) around the 2” pipe in the subfloor. The rubber gasket must be flush with the upper end of the 2” ABS or PVC pipe.

Do Not use any Lubricants.

Tighten (squeeze) the rubber caulking gasket firmly with the caulking nut (use a flat headed screwdriver) and finally insert the plastic frame and strainer on top (without adhesive). The frame and drain cover will be held in a grout joint only once tiling commences.

Set up a continuous 1/2” bead of wedi Joint Sealant along the pans channel on the outer perimeter and only in areas where you can immediately install a building panel into the fresh sealant.

One extra fastener is set into the seam to the next panel to crate a flush transition.

Apply continuous 1/2” beads of sealant between all connections of panels and install with thigthly butted seams. Excess sealant must be spread flat with a putty knife. All seams and fastener heads in the assembly are covered with a secondary 1/2” bead of sealant and spread flat. The seams should be covered 1” on either side of seam. All fastener / washers are covered with sealant stretching 1” over the washer edges.

15 wedi Niches are installed in a cut out in the wedi wall and attached with it‘s flange right into the center of 16 o.c. studs. wedi Joint Sealant is set along the connection of wall to niche.

2 Fasteners each side of the niche are set to create a flush transition to the wall panels.

Another 1/2” bead of wedi Joint

Seal ant is spread over fasteners and seams.

Apply thinset mortar over wood subfloor and reaching 4” into the wedi

Fundo Ligno shower base. Fill the wedi Fundo Ligno channel with thinset or a strip of sealed on wedi Building Panel and apply thinset mortar to the lower corner of the wedi wall panels left and right of any entrance using

1/4” × 1/4” notch trowel.

Apply a modified thinset (ANSI 118.4 or equivalent) across the wood or cement board floor surface and now apply wedi Subliner Dry Sheet waterproofing membrane overlapping into the Ligno base for 4 inches.

Apply wedi‘s prefabricated outside or inside sealing tape corners and sealing tape or Subliner Dry folds as a flashing to the wedi wall panels/

Ligno and Subliner dry sheets as applicable. Install this waterproofing system over the floor substrate outside the shower. All areas subject to water splashes and spray must be waterproofed. wedi recommends to waterproof the entire bathroom floor (including a flashing up into the wall at least to the height of a regular base board or 2“ high) in spaces where curbless showers are being installed.

All seams and ends of the Subliner Dry sheets are covered with a 1/2” bead of wedi Joint Sealant and spread flat using a putty knife. Your shower is ready for tile once the thinset mortar has hardened! Alternatively to Subliner Dry sheet membrane system wedi building panels in 1/4” or 1/2” thickness can be used as the floor tile underlayment in lieu of cement board and Subliner waterproofing. wedi Building Panel would be installed over plywood subfloor and overlap and seal into the

Ligno channel. In such application the Ligno base must be raised to allow its channel to fully stick out from the recessed area so wedi floor building panels can be interlocked with its channel. All seams to wedi walls or Ligno base are sealed internally with wedi Joint Sealant, and are covered with an external 1/2” bead of wedi Joint Sealant spread flat.

Your shower is ready for tiling once thinset under wedi Subliner Dry or wedi Building Panels on floor has cured.

After Installation

2 hours later, provided a temporary dam has been built for this curbless shower. No premixed organic mastic adhesives are used with wedi systems when installed in wet areas. Ceramic tile smaller than 2 x 2“ are not used within wedi Fundom Ligno. Tiles in Ligno showers used for wheel chair accessibility require adhesion in epoxy thinset mortar and grouting using epoxy grout. Non square tiles must be set accordingly and the shortest side of the tile determines the appropriate setting materials. Larger format tile > 4 inches square may be used on wedi Fundo but have to be cut. They have to be cut for their grout joints aligning with the wedi shower base slope lines (where slope fields meet).

wedi Drain Cover Assembly / Insertion

Insert Cover frame into base hole (no glue / no screws). You may caulk between part and tile to create a flexible grout joint. Optional Extension Collar can be cut to height if part is needed. The caulk joint must not create a water barrier damming up the water draining through the thinset bed into the drain from below the tile. Therefore the thinset layer must be continuous toward the drain. Use the black plastic extension collar if you need to raise the wedi frame and cover. Cut extension collar to size and insert below the frame/cover. If not needed, the extension collar may be disposed of as it is not necessary for the functioning of the wedi installation. wedi Cover

Cover frame

Optional Extension Collar

wedi Fundo Riolito neo

wedi’s pre-sloped shower bases Riolito neo feature fully factory sealed and integrated linear drainage systems. The base itself is naturally waterproof as well as mold proof, due to its closed cell XPS foam core. The Riolito neo bases come with the wedi typical strong and ready for tiling surface coating. All

Riolito neo shower bases can be field modified. They can be cut to size or extended using wedi‘s pre-sloped Fundo extensions.

The integrated drain in Riolito neo ensures your installation is not exposed to the risk commonly associated with bonding flange design/surface waterproofing installation-type, single drain products. The unique wedi Fundo Riolito neo bases allow water to drain away through a narrow gap between their drains cover plate and the tile surface finish. wedi Fundo Riolito neo is always equipped with the drain unit but covers are ordered separately. Options for covers include a polished stainless steel version, a double plated brushed stainless steel version, and a tileable version.

Available in 4-way and 2-way or single slope designs with close to the wall drains, wedi Riolito neo features the industries only factory sealed drain for use in custom shower configurations. What is more, the Fundo Riolito neo is available in one piece shower base panels or as a modular system offering a separate drain module and an extension module to combine and configure custom layouts even easier.

Several models with 4 way slope fields provide for a perfect installation when recessing the base into a subfloor where a flush to the floor entry is required.

The second option includes models with a true one way slope towards the linear drain. This latter option is especially designed to accommodate tub to shower conversions without the need to ever move the floor drain pipe.

Linear Drain Shower Floor Solutions

wedi’s Fundo Riolito neo linear drain shower bases feature the only fully sealed and factory integrated waterproof drain assembly available in the market of customizable shower floor systems with linear drainage.

Multiple sizes with different sloped designs, bases are customizable in the field

100 % internally waterproof, mold proof, insulating wedi

XPS closed cell foam core

Curb

Sealing collar

Drain body

Drain to Base Assembly

Building

Panel wedi Fundo Riolito neo

Screws

Fundo Riolito neo employs different drain and drain cover assembly parts. Please refer to the installation manual in the actual product box.

In this section Fundo Riolito neo we are showing the Fundo Riolito neo Drain and Drain Cover parts and assembly.

Several Riolito neo models naturally feature different perimeter height or thickness at the edge. Therefore, pre-made standard notch connections of wedi curbs must be modified in the field for a tight fit to the bases. Ramps and Extension panels can naturally not fit to all models and might be modified in the field as well.

wedi Fundo Riolito neo Installation*

Before Installation:

 Have extra 2 × 4 blocking installed over bottom plate between studs along to support wedi building panel to shower base transition area.

 Floor drain assembly below floor is stabilized, fixed and supported in position, and will not sink under water load.

 Only wedi products (Building Panels, Curb, Joint Sealant and Fasteners) are used for wedi Fundo Shower System assembly.

 Installer has received instructions from wedi technical sales staff or is informed about proper installation methods as described.

 wedi shower bases can be cut to size using a skilsaw. The Z notch channel must be remade and cleaned from sawdust or other possible contamination.

Cut the 2” pipe 1 1/4” below the top of the Subfloor. Use the oval shape cutting template to cut subfloor using a jigsaw to allow wedi drain trap to be inserted and connected to floor pipe using appropriate

ABS compatible or multipurpose cement glue. Please also check cement glue compatibility to floor pipe material.

The drain and trap have to be secured to the subfloor. Drain recess cut out must not add deflection to subfloor. Please be careful to use the oval cutting template where your shower base has it's drain position. While the template features a straight side for easy aligning with a wall, not all

Riolito's drains have the same distance to wall framing.

Assemble the drain unit following the instruction drawing. wedi‘s Riolito neo bases can be cut to size on all sides making drain positions close to the wall possible. Please do not cut into the linear drains plastic flange integrated into the coated foam part of the base. Once cut the 1/2” × 1/2” channels at the new base perimeter must be re-established. When cutting close to the drain channel always leave enough wedi foam for re-making the needed 1/2“ × 1/2“ channel.

Glue and seal the wedi drain trap to the 2” pipe using appropriate solvent cement glue for the plastics involved. Do not screw drain body/trap to floor. Secure with some dabs of wedi joint sealant under flange instead. Mount the sealing collar to the wedi Riolito neo underside counterpart using a manual phillips screwdriver.

Apply a skim coat and finally a combed through bed of a thinset using modified thinset ANSI 118.4 and 1/4” ×

1/4” notch trowel. There are different ways to ensure good bond of the wedi base to the subfloor. Required is a setting bed thickness of min. 3/16“ and max. of 5/16“ (compressed). Applying thinset on both, wedi base and subfloor, is a best practice recommended to achieve full surface coverage adhesion.

* Installations in Australia & New Zealand: Please refer to Installation manuals featuring the applicable job site requirements and wedi drains.

Trowel the thinset on the rear side of the Fundo again using a

1/4” × 1/4” notch trowel.

Press the Fundo firmly into the thinset bed, ensuring that the installation is level and void free. Ensure wedi drain‘s sealing gasket is firmly inserted in the wedi trap with no chance that thinset could have pushed into this connection area.

Apply some weight equally and for at least 30 minutes

(thinset bags). Do NOT step on the drain module to push /connect to drain body or thinset.

Set up a continuous 1/2” bead of wedi Joint Sealant at the perimeter channel and only in areas where you can immediately install a wedi Building

Panel into the fresh sealant.

Apply continuous 1/2” beads of sealant between all connections of panels and install with tightly butted seams. Excess sealant must be spread flat with a putty knife. All seams and fastener heads in the assembly are covered with a secondary 1/2” bead of sealant and spread flat. The seams should be covered 3/4” to 1” on either side of seam. All fastener/ washers are covered with sealant stretching 1” over the washer edges.

10 wedi Niches are installed in a cut out in the wedi wall and attached with it‘s flange right into the center of 16 o.c. studs. wedi sealant is set along the connection of wall to niche.

2 Fasteners each side of the niche are set to create a flush transition to the wall panels.

Another 1/2” bead of wedi seal ant is spread over fasteners and seams.

A continuous 1/2” bead of sealant is set into the channel and along the vertical curb notch part. A circle of 1/2” sealant bead is set against the wall panels (and) or the curb sides where the curb attaches. A 1/2” × 1/2” bed of thinset mortar is applied to the subfloor and just a skimcoat on the foam bottom part of the curb as a best practice. The tightly cut to fit curb is pressed into the connection. Weight is applied on and against the curb (from outside) and another 1/2” bead of sealant is applied over all curb seams and spread flat. The seams must be covered 3/4” to 1” either side of a seam.

Curb connection notches must be cut to fit select Riolito neo bases with perimeter thickness higher than 1 1/2“.

See important considerations „After Installation“ in wedi Fundo

Riolito neo Modular manual on the following pages.

wedi Fundo Riolito neo Modular

wedi‘s Fundo Riolito neo System feature the only fully sealed and factory integrated waterproof drain assembly available in the market of customizable shower floor systems with linear drainage.

They are available in two design options. The first option includes models featuring a one-piece shower base including the drain trench. These provide

1-way or 4-way slopes. The second option, Riolito neo Modular is designed to offer more flexibility as it consists of two basic elements: one module including the line module which is a trench drain integrate in a wedi base module, the other being a sloped extension panel. Drainage can be installed close to the wall or two extension models leading away from either side of an i.e. centered drain. The line modules may also be used with mortar bed shower applications (to be topically waterproofed using wedi Subliner Dry, connecting to the Riolito neo line module).

Component 2:

Fundo Riolito neo Extension

Module – 100 % internally waterproof, mold proof, insulating wedi XPS closed cell foam core

Linear Drain Shower Floor Solutions

Curb wedi Fundo Riolito neo Modular

Sealing collar

Drain body

Drain to Base Assembly

Component 1: Fundo Riolito neo Line Module – Multifunctional and customizable to the user‘s demands

Building

Panel

Screws

wedi Fundo Riolito neo Modular Installation*

Before Installation:

 Have extra 2 × 4 blocking installed over bottom plate between studs along to support wedi building panel to shower base transition area.

 Floor drain assembly below floor is stabilized, fixed and supported in

position, and will not sink under water load.

 Only wedi products (Building Panels, Curb, Joint Sealant and Fasteners) are used for wedi Fundo Shower System assembly.

 Installer has received instructions from wedi technical sales staff or is

informed about proper installation methods as described.

ABS compatible or multipurpose cement glue. Please also check cement glue compatibility to floor pipe material.

Riolito's drains have the same distance to wall framing.

Glue and seal the wedi drain trap to the 2” pipe using appropriate solvent cement glue for the plastics involved. Do not screw drain body/trap to floor. Secure with some dabs of wedi joint sealant under flange instead. Mount the sealing collar to the wedi Riolito neo Modular underside counterpart using a manual phillips screwdriver.

Apply a skim coat and finally a combed through bed of a thinset using modified thinset ANSI

118.4 and 1/4” × 1/4” (6 mm

× 6 mm) notch trowel. There are different ways to ensure good bond of the wedi base to the subfloor. Required is a setting bed thickness of min.

3/16“ and max. of 5/16“ (compressed). Applying thinset on both, wedi base and subfloor, is a best practice recommended to achieve full surface coverage adhesion. wedi recommends to cut and dry fit both floor modules to shower stall size and drain location.

* Installations in Australia & New Zealand: Please refer to Installation manuals featuring the applicable job site requirements and wedi drains.

05 06

Trowel the thinset on the rear side of the Fundo Riolitio neo Module

“Drain” again using a 1/4” × 1/4” (6 mm × 6 mm) notch trowel. Press the

Fundo Riolito neo Module “Line Drain” into the thinset so that the sealing gasket moves smoothly into the drain body without contamination through thinset. Make sure the entire wedi cement coated underside of the drain module will have thinset support/coverage. Do NOT step on the drain module to push /connect to drain body or thinset. Apply a 1/2” (13 mm) bead of wedi Joint Sealant to the module‘s Z notch channel and insert the second module, the “Extension”. The Module “Extension”, once cut to length, is also installed using thinset mortar and using the same technique as shown under 4. Apply a 1/2” (13 mm) bead of wedi joint sealant over the seam between both modules and spread flat using a putty knife. Apply weights.

Set up a continuous 1/2” (13 mm) bead of wedi Joint Sealant at the perimeter channel and only in areas where you can immediately install a wedi

Building Panel into the fresh sealant.

Push the wedi Building Panel all the way into the channel of the shower base channel and its bead of sealant. Smooth out any pushed out sealant on inside seam using a putty knife.

Fasten the panels directly to the studs starting 1 ft (300 mm) above the base and at a rate of 1 fastener per 1ft (300 mm).

One extra fastener is set into the seam to the next panel to create a flush transition.

Apply continuous 1/2” (13 mm) bead of sealant between all connections of panels and install with tightly butted seams. Excess sealant must be spread flat with a putty knife. All seams and fastener heads in the assembly are covered with a secondary 1/2” (13 mm) bead of sealant and spread flat. The seams should be covered 3/4” to 1” (19 mm to 25 mm) on either side of seam. All fastener/washers are covered with sealant stretching 1”

(25 mm) over the washer edges.

10 wedi Niches are installed in a cut out in the wedi wall and attached with it‘s flange right into the center of 16 o.c.

(406 mm) studs. wedi Joint

Sealant is set along the connection of wall to niche.

2 Fasteners each side of the niche are set to create a flush transition to the wall panels.

Another 1/2” (13 mm) bead of wedi seal ant is spread over fasteners and seams.

A continuous 1/2” (13 mm) bead of sealant is set into the channel and along the vertical curb notch part. A circle of 1/2” (13 mm) sealant bead is set against the wall panels (and) or the curb sides where the curb attaches.

A 1/2” × 1/2” (13 mm × 13 mm) bed of thinset mortar is applied to the subfloor. The tightly cut to fit curb is pressed into the connection. Weight is applied on and against the curb ( from the outside) and another 1/2”

(13 mm) bead of sealant is applied over all curb seams and spread flat. The seams must be covered 3/4” to 1” (19 mm to 25 mm) either side of a seam.

Curb connection notches must be cut to tightly fit select Riolito neo bases.

After Installation

All visible joints or seams in the installation are visibly covered and reinforced with wedi joint sealant applied flat over the seams. Coverage of wedi joint sealant over all seams should be at least 3/4-1 inch on either side of the seam. The joint sealant should be no less than 1/16“ thick for strength. Do not add mesh tape into the wedi joint sealant. This may only put the waterproof performance at risk and will not strengthen the system‘s resistance against movement related stresses. Once wedi joint sealant application over all shower system seams has been completed, a water flood test may be performed as early as 2 hours later. No premixed organic mastic adhesives are used with wedi systems when installed in wet areas. Ceramic tile smaller than 2 x 2“ square may be adhered using a modified thinset mortar and may be grouted using polymer modified cement based grout. Ceramic tiles smaller 1 x 1“ square require adhesion in epoxy thinset mortar and grouting using epoxy grout. Non square tiles must be set accordingly and the shortest side of the tile determines the appropriate setting materials. Pebble Stones may be set and grouted using both, modified cement based thinset mortars and grouts or epoxy thinset mortar and grout, or a combination. Larger format tile > 2 inches square may be used on wedi Fundo Riolito neo. They may have to be cut for their grout joints aligning with the wedi shower base slope lines if present, depending on model used (where slope fields meet).

Installation instructions wedi Fundo Riolito neo / Riolito neo Modular Drain Cover

01 Drain Cover Fundo Riolito neo standard: High Grade Polished Stainless

Steel Standard Version

02 Drain Cover Fundo Riolito neo exclusive: High Grade Double Plated Stainless Steel Version

03 Drain Cover Fundo Riolito neo tileable: Can be tiled with epoxy glue/ adhesive or wedi joint sealant. Can be used for 1/4” and 1/2” tile / stone (reverse cover)

Drain cover can be adjusted from

+ 5 mm to + 25 mm from Riolito neo base surface. The cover supports may be extended out to needed height using the allen key included in box.

The supports may also be cut shorter along prefabricated cutting lines before assembly with allen key.

Linear channel cover standard and exclusive

01 02

CLICK!

03 5 – 25 mm 04

05 06 07

X+1 mm

09 10

CLICK!

Linear channel cover tileable

01 5 – 25 mm 02 03 04

X+1 mm

05 06 07 08

09 10

wedi Sanoasa Benches

Comfort means something different to each person. The feeling of quiet and relaxation when sitting in the shower, though, is a very pleasant experience for everyone. The wedi Sanoasa benches provide plenty of space to comfortably relax, pampering both your body and mind in your own small wellness temple. The smart construction enables an unequalled freedom of visual design; both the seating areas and the carrier elements can not only be positioned the way you like, but also their shapes and sizes can be modified to suit. The benches attach to shower wall and floor surfaces using wedi

Joint Sealant or, where a gap opens to the floor due to a sloped shower floor, thinset is used to fill the gap and mesh tape is applied over the thinset application or floor to bench seam.

Highly stable carrier element, available in two widths

Bench element with slopes

100% waterproof XPS core

More wedi Prefabricated Shower Seats and Benches

wedi prefabricated shower seats and benches install much quicker and easier than metal tray or concrete seats. Plus, they bond well to thinset mortar and are 100 % waterproof due to the extruded polystyrene closed cell foam core which is manufactured without the use of CFC and contains no HBCD.

They will not cause efflorescence or discolorations or waterproofing issues as frequently observed with products including those requiring mortar fills.

Create the perfect waterproof seating solution for your shower. wedi Prefabricated Suspended Corner Seats do not require additional blocking installed in the framing. Their mounting brackets are fastened into existing wall studs.

Very strong: handles loads up to 350 lbs

Solid foam core triangle corner seat for heavy duty

Specialty Applications – the wedi building panel as solution

Round and curved walls

01 02

Create a series of cuts into the wedi Building Panels 1/2 the thickness of the panel deep. The distance between cuts depends on the tightness of the radius needed later. Use a circular saw for these cuts. A wide range of other shapes are possible using the wedi Building Panel. All you need is a template shaped to suit your needs. A template may not be needed for simpler shaping.

A B

Cut the wedi Building Panel using a utility knife and straight edge. This way wave shape constructions can be produced. For a small radius – cut out wedges from the building panel or cut the wedi Building Panel using a hand-held circular saw and bend it into a curve.

Installation of wedi Vapor Barrier in wedi steam room applications

01 02

Apply over all wedi inside surfaces in steam rooms prior to tiling. Vapor

Barrier Components A and B are supplied in pre-measured quantities.

Add Comp. B to Comp. A by piercing a hole through the top (rubber membrane) and the bottom of Component B. Assure that Component

B completely flows out of the container. Always mix a complete kit in the proportions supplied. Do not alter mixing ratios. Only mix what you can apply within pot life. Stir mixture for approx. 5 minutes to a homogenous, streak free consistency, using a slow speed drill (approx. 300 rpm) with a clean Polished Steel Jiffy blade. Avoid entrapping air. Ensure that the material at the bottom and sides of the pail is agitated well. After mixing, pour it into a clean metal container and carefully mix it again for additional 30 seconds. Make sure not to mix too fast to avoid trapping air. Pour fully mixed product into a metal painters tray. Apply to the clean wedi substrate, by non-shed roller or notched squeegee. A thorough 2-Coat Application with a dry time of

03 04 approximately 30 minutes in between the two coats is required. Each coat should be 8 mils thick (wet thickness=dry thickness) for a total of

16 mils (wet thickness = dry thickness) for the complete application.

The surface is ready for tiling using an epoxy mortar according to ANSI

118.3 or a cement based, modified thinset mortar according to ANSI

118.4 (must be recommended for extreme wet areas with frequent and strong temperature changes) only 3 1/2 hours after final application of the second wedi vapor barrier coat. Tiling must be completed within 5 days maximum after application of the final, second coat has been left to cure for 3 ½ hours. If tiling must commence later, the surface has to be roughened for best adhesion using fine sandpaper and cleaning off the dust later. A new surface coat of the wedi vapor barrier must be installed as a primer surface up to 8 mil thick. The primer coat must be allowed to dry for 3 1/2 hours and again can be tiled over within 5 days.

Specialty Applications – the wedi building panel as solution

Building Custom Seats and Benches Using 1 1/2” or 2” thick wedi Building Panels

01 02

Measure and cut the bench pieces off a wedi 2” thick Building Panel and dry fit. When installing a corner seat, the panel edges are mitered for a tight fit. To achieve a slope, the part’s upper ends are cut down with a slight angle towards the front of the bench. Optionally, create a pitch using wedi joint sealant as a “wet shim”. The wedi parts are adhered to the wall using thinset mortar or wedi

Joint Sealant. Adjoining parts are glued together using wedi Joint

Sealant continuously applied along all foam edges of a panel part.

Excess is spread flat over the seams using a putty knife. Where the part’s backs meet the wedi wall, modified thinset mortar is used in a full contact surface bed. Once the bench is built, a final bead of wedi Joint Sealant is applied to safely seal all seams to the wedi wall. The vertical front part of the bench will show a small gap to the pitched floor. Please fill with thinset mortar and alkali resistant

03 fiberglass mesh tape by wedi, applied over this seam. Alternatively, benches and seats are offered as prefabricated units made by wedi.

For longer or larger benches built from our 2” building panel, always install one spacer/support made of wedi 2” Building Panel every 18 inches in either direction. Over blue exposed foam edges please adhere a wedi Building Panel strip to foam using wedi Joint

Sealant. This will create a cement based surface to adhere tile to it.

Optionally, the blue foam may be covered with wedi Joint Sealant. The covering of the blue foam areas is not necessary, where tile is used that will overlap and cover the blue area with no more than 50 % of its size. Such larger tile is thinset adhered to seat including the foam surface. The maximum weight allowance on such benches built with support with a difference of 18 inches in all directions is 500 pounds per square foot.

Installation on tub walls

Measure and cut wedi Building Panel to fit the 16 inch o.c. framework

(wood or metal). Notch out all panels if installed around the perimeter of a flange tub to integrate the flange and achieve a plumb wall with square and tight corners.

Attach a notched panel to the framework with a 1/2” bead of wedi

Joint Sealant between the notch and flange. Attach the panel to the framework using wedi Washers and Screws at a rate of 1 every 12 inches along the studs. Leave a gap of 1/8" between tub edge and wedi panel bottom end to allow for movement of the tub. Alternatively apply a bead of wedi Joint Sealant in between both materials.

Apply a continuous 1/2” bead of wedi Joint Sealant on the top blue foam edge of the wedi Building Panel before installing the next panel, butting tightly into the sealant. Set another wedi Washer and Screw into the seam to create a flush transition between panels and smooth over excess sealant. When installing a wedi side panel against the already fixed wedi back wall, apply a continuous 1/2” bead of wedi Joint

Sealant vertically on the back wall wedi panel where both panels will meet. Apply compression to the wedi Joint Sealant when moving the wedi side panel into position before fastening it. Finally and after all wedi Building Panels are installed a second 1/2” bead of wedi Joint

Sealant is applied over all seams and fastener points and spread flat using a putty knife.

Technical Properties



wedi Systems

Properties & Test Methods Value (wedi Building Panel and Fundo Shower System Components)

Thermal Conductivity

Tensile Strength

Shear Strength

Waterproof

Capillarity

R-Value

Flexural Strength

75°F (25°C) - ASTM C518

ASTM C297

Under conditions required in ANSI A118.10-1999 28 day Shear Strength: 95 psi

84 day Shear Strength: 100 psi

100 day Shear Strength: 98 psi

ASTM D4068 / ANSI A118.10-1999

75°F (25°) - ASTM C518

0.23 Bbtu in/hr F

65 psi

Passed

4.3hr ft. 2 F/Btu/in (R Value for 1” wedi = 4.3)

Robinson Floor Test

Fastener Pull Through

Temperature Limits

ASTM C947

ASTM C627

ASTM C473

627 psi

Heavy duty commercial use, passed

Wet 131.8 lb./Dry 196.2 lb.

-58 / +175° F

Freeze & Thaw

Waterproofness of Assembly

Fungus / Bacteria Resistance

Accelerated Aging

UL 1715

Linear Variation

Surface Burning Characteristics

Floor and Trench Drain Compliance

ASTM C666 - 25 Cycles

ASTM E331

ASTM G21

AC 71 - 25 Cycles

Fire Test of interior Finish Material

AC 159/ASTM 1037-39

ASTM E 84-04

ASME A112.18.2

No disintegration/change

Passed, wedi Fundo Kit assembly (complete sytsem)

Passed, No Growth

No disintegration

Passed, flame spread <10

Passed, less than 0.07%

Flame Spread of 10 or less

Smoke Developed Index of 95

Passed, Compliant (ICC PMG 1189)

Weight for wedi Building Panels Width

3’

Length

5’

Thickness

1/4”

1/2”

Weight

8.07 lb.

8.67 lb.

ICC-PMG 1189 Report



National Building Code Compliances

WEDI FUNDO SHOWER SYSTEM AND TILE BACKER BOARD UNDERLAYMENTS

Compliance with the following codes

2018, 2015, 2012 and 2009 International Plumbing Code ® (IPC)

2018, 2015, 2012 and 2009 International Residential Code ® (IRC)

2018, 2015, 2012 and 2009 International Building Code ® (IBC)

2015, 2012 and 2009 National Standard Plumbing Code ®

2015, 2012 and 2009 Uniform Plumbing Code ® (UPC)*

(NSPC)

2015, 2010 and 2005 National Plumbing Code of Canada**

* Uniform Plumbing Code is a copyrighted publication if the International Association of Plumbing and Mechanical Officials

** National Plumbing Code of Canada is a copyrighted publication of National Research Council Canada

Compliance with the following standards

ANSI A 118.10-2014, Load Bearing, Bonded, Waterproof Membranes for Thin-Set Ceramic Tile and Dimension Stone Installations

ASME A 112.6.3-2016, Floor and Trench Drains

ICC-ES EG 159, Evaluation Guideline for Composite Backer Board (Approved Dec 2004)

ICC-ES AC 71, Acceptance Criteria for Foam Plastic Sheathing Panels Used as Water Resistive

Barriers (Approved Feb 2003, Ed Revised Nov 2013)

IAPMO PS 46-2012, Field-Fabricated Tiling Kits

IAPMO PS 106-2015e1, Tileable Shower Receptors and Shower Kits

wedi PRO Certification and 15 / 20 Year Warranty Program

In certain circumstances, in lieu of the foregoing 10-Year Limited Warranty, wedi offers a 15-Year Limited Warranty and 20-Year Limited Warranty, pursuant to which wedi warrants the Products shall be free of manufacturing defects and conform to wedi’s published specifications for a total of either

15 years or 20 years when installed as part of a “15-Year Warranty Installation” or “20-Year Warranty Installation,” by a “PRO Certified Installer,” in a

“Registered Installation”. Find Details on wedi’s 15/20 Year Warranty Options on www.wedicorp.com.

20 years warranty for a wedi bathroom system

15 years warranty for a wedi shower system

PRO



wedi’s performance shower systems and its unprecedented warranty coverage and service meet great wedi installers



Sign up for the wedi Pro Certification Classes

– and enjoy wedi’s 15 or 20 year full package warranty options

wedi Building Panel

Description Width x Length x Thickness wedi Building Panel 3’ x 5’ x 1/4” (914 x 1524 x 6 mm) wedi Building Panel 3’ x 5’ x 1/2” (914 x 1524 x 12.7 mm) wedi Building Panel 2’ x 4’ x 1/8” (600 x 1200 x 4 mm) wedi Building Panel wedi Building Panel wedi Building Panel wedi Building Panel

3’ x 5’ x 5/8” (914 x 1524 x 15.8 mm)

2’ x 8’ x 1” (600 x 2500 x 25.4 mm)

2’ x 8’ x 3/4” (600 x 2500 x 20 mm)

2’ x 8’ x 1 1/4” (600 x 2500 x 30 mm)

Unit/Palette

50 panels = 750 sq. ft.

136 panels = 1,088 sq. ft. 010000004

50 panels = 750 sq. ft.

56 panels = 896 sq. ft.

50 panels = 800 sq. ft.

36 panels = 576 sq. ft.

wedi Building Panel 2’ x 8’ x 1 1/2” (600 x 2500 x 40 mm) wedi Building Panel 2’ x 8’ x 2” (600 x 2500 x 50 mm)

36 panels = 576 sq. ft.

24 panels = 384 sq. ft.

wedi Building Panel 2’ × 8’ × 3 1/15” (600 × 2500 × 80 mm) 12 panels = 192 sq. ft.

wedi Building Panel 2’ × 8’ × 3 9/10” (600 × 2500 × 100 mm) 20 panels = 320 sq. ft.

Item #

010718006

010717064

010716316

010719325

010000020

010000030

010000040

010000050

010710080

(special order only)

010710199

(special order only)

Retail Price

$ 53.86

$ 55.87

$ 29.12

$ 69.59

$ 79.04

$ 71.51

$ 80.50

$ 95.24

$ 99.00

$ 119.36

$ 151.72

wedi Building Panel XL & XXL

Description wedi Building Panel XL

Width x Length x Thickness

3’ x 8’ x 1/2” (900 x 2500 x 12.5 mm)

Unit/Palette Item #

26 panels = 624 sq. ft. 010000912 wedi Building Panel XXL 4’ x 8’ x 1/2” (1200 x 2600 x 12.5 mm) 26 panels = 858 sq. ft. 010001612 wedi Building Panel XXL 4’ x 8’ x 2” (1200 x 2500 x 50 mm) 12 panels = 396 sq. ft. 010001250

Retail Price

$ 92.60

$ 138.63

$ 239.52

wedi Shower and Bath Tub Surround Kit

Description wedi Shower and Bath

Tub Surround Kit

Kit Contents

(5) wedi 3’ × 5’ × 1/2“ Building Panels

(914 × 1524 × 12.7 mm)

(5) wedi Joint Sealant, 10.5 oz. (310 ml)

(1) Mixing Valve Flexi Collar

(1) Flexi Collar

(1) Corner Putty Knife

100 ct. of wedi Tab Steel Washers

100 ct. of wedi Galvanized Screws

Unit

1 kit

For Tub surrounds, Shower Wall Surrounds and use with Onestep Shower Bases.

Underlayment Kit

Item #

US4000001

Retail Price

$ 371.49

Description

Underlayment Kit

Kit Contents

(5) wedi 2’ × 4’ × 1/4” Building Panels

(600 × 1250 × 6 mm)

(1) wedi Joint Sealant, 10.5 oz. (30 cl)

40 × tabless washers and wood screws

Especially for use with electric floor warming systems.

Unit

1 kit

Item #

US4000002

Retail Price

$ 180.67

wedi Fundo Primo | Square and Rectangular Shower Bases, Center Drain

Description wedi Fundo Primo, square wedi Fundo Primo, square wedi Fundo Primo, square wedi Fundo Primo, square wedi Fundo Primo, rectangular wedi Fundo Primo, rectangular wedi Fundo Primo, rectangular wedi Fundo Primo, rectangular wedi Fundo Primo, rectangular wedi Fundo Primo, rectangular wedi Fundo Primo, rectangular wedi Fundo Primo, rectangular

Dimensions

36” × 36” incl. drain (914 × 914 mm)

48” x 48” incl. drain (1220 × 1220 mm) 1 pc

60” x 60” incl. drain (1524 × 1524 mm) 1 pc

72” x 72” incl. drain (1830 × 1830 mm) 1 pc

36” x 48” incl. drain (914 × 1220 mm)

36” x 60” incl. drain (914 × 1524 mm)

48” x 60” incl. drain (1220 × 1524 mm) 1 pc

48” x 72” incl. drain (1220 × 1830 mm) 1 pc

60” x 72” incl. drain (1524 × 1830 mm) 1 pc

48” x 84” incl. drain (1220 × 2134 mm)

60” x 84” incl. drain (1524 × 2134 mm)

36” x 72” incl. drain (914 × 1830 mm)

Unit

1 pc

Item #

073735507

073735505

073735518

073735524

073735516

073735506

073735509

073735508

073735519

073735522

073735523

073735525

wedi Fundo elements vary in thickness from 1 1/2” to 2” at the perimeter. When working with modular wedi curbs or ramps the connection notch might need to be adjusted in the field.

Equipped with Drain Unit and Cover Set Brushed Stainless Steel.

Retail Price

$ 469.98

$ 651.37

$ 1,161.18

$ 1,705.35

$ 598.84

$ 639.82

$ 847.83

$ 1,003.32

$ 1,375.42

$ 1,319.72

$ 1,649.65

$ 680.79

wedi Fundo Primo | Rectangular Shower Base, Offset Drain

Description wedi Fundo Primo, rectangular, offset drain wedi Fundo Primo, rectangular, corner drain

Dimensions

36” x 72” incl. drain (914 × 1830 mm)

Unit

1 pc

60” x 72” incl. drain (1524 × 1830 mm) 1 pc

For tub replacement installations. Cut unit to always meet drain and shower size.

Equipped with Drain Unit and Cover Set Brushed Stainless Steel.

Item #

073735521

073735526

Retail Price

$ 680.79

$ 1395.20

wedi Fundo Primo Shower Kit

Description wedi Fundo Primo Shower Kit wedi Fundo Primo Shower Kit wedi Fundo Primo Shower Kit wedi Fundo Primo Shower Kit wedi Fundo Primo Shower Kit wedi Fundo Primo Shower Kit wedi Fundo Primo Shower Kit

Dimension

36” x 36” center drain (914 × 914 mm)

36” x 48” center drain (914 × 1220 mm)

36” x 60” center drain (914 × 1524 mm)

36” x 72” center drain (914 × 1830 mm)

36” x 72” offset drain (914 × 1830 mm)

48” x 60” center drain (1220 × 1524 mm)

Unit Item #

1 pc

48” x 48” center drain (1220 × 1220 mm) 1 pc

1 pc

US2000002

US2000007

US2000004

US2000003

US2000001

US2000008

US2000005

Retail Price

$ 889.83

$ 1,136.01

$ 1,244.20

$ 1,177.62

$ 1,217.15

$ 1,450.18 wedi Fundo Primo Shower Kit 48” x 72” center drain (1220 × 1830 mm) 1 pc US2000006 $ 1,662.40

 1 wedi Fundo Pan

 wedi Building Panels to cover up to (3) 80” walls

 1 drain assembly

 1 Full Foam Curb Lean

 wedi Joint Sealant

 Fasteners

 wedi putty knife

 wedi Flexi Collar

 wedi Mixing Valve Flexi Collar

 Wall height 80”

wedi Fundo Ligno | Square and Rectangular Shower Bases, Center Drain

Description wedi Fundo Ligno, square wedi Fundo Ligno, square wedi Fundo Ligno, rectangular wedi Fundo Ligno, rectangular wedi Fundo Ligno, rectangular

Dimensions Unit Item #

48“ x 48“ x 3/4“ (1220 × 1220 × 19 mm) 1 pc 073732015

60“ x 60“ x 3/4“ (1524 × 1524 × 19 mm) 1 pc 073732018

36“ x 48“ x 3/4“ (914 × 1220 × 19 mm)

36“ x 60“ x 3/4“ (914 × 1524 × 19 mm)

1 pc

48“ x 60“ x 3/4“ (1220 × 1524 × 19 mm) 1 pc

073732014

073732016

073732017

Retail Price

$ 803.40

$ 1,390.42

$ 745.56

$ 792.69

$ 1,060.49

wedi Fundo / Pre-Sloped Extension Panels

Description Width x Length x Thickness Unit Item # Retail Price wedi Shower Base Extension 24” x 48”, sloped 1/4”/ft.

(609.8 × 1219.2 mm, sloped 6 mm in 30 mm) sheet wedi Shower Base Extension

Lean wedi Fundo Ligno Extension

Panel

12” x 72”, sloped 1/4”/ft.

(304.8 × 1828.8 mm, sloped 6 mm in 30 mm)

12” x 60”, sloped 1/4”/ft.

(304.8 x 1524 mm, sloped 6 mm in 30 mm) sheet sheet

073783528

073783523

073732030

$ 233.32

$ 160.37

$ 178.82

 Slope extends over 24” or 12” direction of either extension panel and pre-grooved

 Extension panels are designed to interlock with Fundo Primo bases and 4 way slope Fundo Riolito neo bases. The

installation height must be increased if connected to Fundo and Ligno shower bases thicker than 1 1/2” at perimeter.

wedi Fundo Drain Units & Kits Standard | Drain, PVC, ABS and Brass

Description wedi Fundo Drain Kit Standard, ABS, Compression Fit wedi Fundo Drain Kit; Brass, Compression Fit wedi Fundo Glue Drain Kit, ABS wedi Fundo Compression Fit Drain Unit wedi Fundo Brass Compression Fit Drain Unit wedi Fundo Glue Drain, ABS wedi Angle Drain

Unit

1 pc

 Drain Units connect to Schedule 40 pipe

 Compression Fit Drain units can be used with ABS/PVC pipe

 Glue Drain units can be used with ABS floor pipe

 Items sold as Kit contain Drain unit, extension collar and Cover Set standard

 For Fundo Primo and Ligno

Item #

US1000003

US1000004

US1000007

US1000012

US1000011

US1000010

US1000027

Retail Price

$ 77.66

$ 92.39

$ 77.66

$ 10.71

$ 32.96

$ 13.39

$ 117.34

wedi Fundo Drain Accessories | 2” Sealing Gasket

Description

Special Rubber Caulking Gasket for Cast Iron Pipe Connection

Special Rubber Caulking Gasket for Copper Pipe Connection

 For use in Compression Fit Drain units

 Specialty Gaskets available upon request

Unit

1 pc

wedi Fundo Standard | Drain Cover, Stainless Steel Base

Item #

US5000030

US5000031

Retail Price

$ 18.09

Description wedi Fundo Drain Cover Set,

Brushed Stainless Steel wedi Fundo Drain Cover Set,

Brushed Stainless Steel with Screws wedi Fundo Drain Cover Set,

Oil Rubbed Bronze

Width x Length

4” x 4” (102 × 102 mm)

Unit

1 pc

Item #

US1000009

US1000029

4” x 4” (102 × 102 mm) 1 pc US1000008

 For this drain cover, the height of your tiling must be at least 1/4”.

 For use with wedi Fundo Primo, Ligno, Trollo, Nautilo bases.

 The Standard Drain Cover included in Fundo Systems Primo/Ligno/Trollo/Nautilo is US1000009

 1 drain cover, stainless steel

 1 frame, stainless steel

Retail Price

$ 64.27

$ 70.97

wedi Fundo Drain Wrench

Description

Heavy Duty Drain Wrench

Unit

1 pc

Support tool used to tighten wedi Fundo Primo compression fit rubber gaskets

Item #

US5000032

Retail Price

$ 16.07

wedi Fundo Fino | Optional Design Covers, Stainless Steel Brushed

Set 1.1

Set 3.1.2

Set 3.1

wedi Fundo Fino

Tileable Cover Plate

Set 1.1.2

Description wedi Fundo Fino Cover Set 1.1, square 4“ x 4“ (102 × 102 mm) (Daisy Design) wedi Fundo Fino Cover Set 1.1.2, round (Daisy Design) wedi Fundo Fino Cover Set 1.3, square 4“ x 4“ (102 × 102 mm) / w. Screws (Daisy Design) wedi Fundo Fino Cover Set 3.1, square 4“ x 4“ (102 × 102 mm) (Pebbles Design) wedi Fundo Fino Cover Set 3.1.2, round (Pebbles Design) wedi Fundo Fino Cover Set 3.3, square 4“ x 4“ (102 × 102 mm) / w. Screws (Pebbles Design) wedi Fundo Fino Tileable Cover Plate, square 4“ x 4“ (102 × 102 mm) wedi Fundo Fino Stainless Steel Cover,

4" x 4" (102 × 102 mm) / w. Screws

Unit

1 pc

Item #

US1000021

US1000023

US1000022

US1000024

US1000026

US1000025

US1000020

US1000029

Retail Price

 For use with wedi Fundo Primo, Ligno, Trollo, Nautilo bases.

 Tileable cover plate surface is elevated 1/16“ over tile surface of a Fundo base. For a flush tile installation, wedi joint sealant spot bonding may be used to install the tile inside the cover so height is reduced versus the thinset bed build up under the tile on the shower base.

 1 drain cover, stainless steel

 1 Frame, stainless steel

$ 110.00

$ 64.27

wedi Fundo Riolito neo | Shower Base, with Integrated Channel Drain

Description wedi Fundo Riolito neo, floor base, with channel drain wedi Fundo Riolito neo, floor base, with channel drain wedi Fundo Riolito neo, floor base, with channel drain wedi Fundo Riolito neo, floor base, with channel drain wedi Fundo Riolito neo, floor base, with channel drain

External Dimensions

Length x Width x Height

36” x 60” x 2 3/8“ incl. drain, four-way slope (914 × 1524 × 51 mm)

Channel

Length

Item #

43 5/16”

(1100 mm) 075100016

48” x 60” x 2 1/2“ incl. drain, four-way slope (1220 × 1524 × 63 mm)

48” x 72” x 2” incl. drain, four-way slope (1220 × 1830 × 51 mm)

32” x 72” x (2 3/4” – 1 3/8”) incl. drain, single slope (one-way slope)

(813 × 1830 × 63 – 35.4 mm)

32” x 72” x 2 3/4” incl. drain, two-way slope, drain 12” offset

27 1/2”

(700 mm)

43 5/16”

(1100 mm) 075100014

27 1/2”

(700 mm)

27 1/2”

(700 mm)

075100012

075100015

075100035

Retail Price

$ 819.00

$ 1,038.70

$ 1,168.70

$ 830.00

wedi Fundo Riolito neo Modular | Shower Base, with Integrated Channel Drain

Description wedi Fundo Riolito neo

Modular, line module wedi Fundo Riolito neo

Modular, extension module wedi Fundo Riolito neo

Modular, extension module

External Dimensions

Length x Width x Height

32” × 5 3/4” (813 × 146 mm)

Height Line Module: 1 3/8“ (35.4 mm)

48” × 5 3/4” (1220 × 146 mm)

Height Line Module: 1 3/8” (35.4 mm)

32” × 66 3/4” (813 × 1700 mm)

Height Line Module:

1 3/8” (35.4 mm) – 2 3/16” (55.6 mm)

48” × 66 3/4” (1200 × 1700 mm)

Height Line Module:

1 3/8” (35.4 mm) – 2 3/16” (55.6 mm)

–

Channel

Length

27 1/2“

(700 mm)

Item #

–

075100052

43 5/16“

(1100 mm) 075100053

075100050

075100051

Retail Price

$ 300.00

$ 360.00

$ 510.00

$ 680.00

wedi Fundo Riolito neo Shower Kit

Description wedi Fundo Riolito neo

Shower Kit

Dimension

32” x 72” One-Sided Slope

(660 × 1830 mm)

 Wall height 80”

 Riolito neo Standard Drain Cover Plate included

Unit

1 pc

Item #

US4000010

Retail Price

$ 1,498.00

 1 wedi Fundo Shower Pan

 wedi Building Panels to cover up to (3) 80” walls

 1 drain assembly

 1 Full Foam Curb Lean

 Fasteners

 wedi Joint Sealant

 wedi Flexi Collar

 wedi Mixing Valve Flexi Collar

 wedi Riolito neo Standard Cover Plate

wedi Fundo Riolito neo Standard | Cover Plate, Stainless Steel

Description wedi Fundo Riolito neo Standard drain cover for 36” x 60” and 48” x 72“ Riolito neo base

(914 × 1524 mm and 1220 × 1830 mm) wedi Fundo Riolito neo Standard drain cover for 48” x 60” and 32” x 72” Riolito neo base

(1220 × 1524 mm and 813 × 1830 mm)

Width x Length x Height

1 5/8” × 43 1/4” × 3/4”

(41 × 1100 × 19 mm)

1 5/8” × 27 5/8” × 3/4”

(41 × 700 × 19 mm)

For tile installation heights of between 3/16” to 1”

For Fundo Bases Riolito neo and Riolito neo Modular.

Unit Item #

1 pc 676797045

1 pc 676797048

Retail Price

$ 190.00

$ 146.00

wedi Fundo Riolito neo Exclusive | Cover Plate, Stainless Steel

Description Width x Length x Height wedi Fundo Riolito neo Exclusive drain cover for

36” x 60” and 48” x 72“ Riolito neo base (914

× 1524 mm and 1220 × 1830 mm)

1 5/8” × 43 1/4” × 3/4”

(41 × 1100 × 19 mm) wedi Fundo Riolito neo Exclusive drain cover for 48” x 60” and 32” x 72” Riolito neo base

(1220 × 1524 mm and 813 × 1830 mm)

1 5/8” × 27 5/8” × 3/4”

(41 × 700 × 19 mm)

For tile installation heights of between 3/16” to 1”

For Fundo Bases Riolito neo and Riolito neo Modular.

Unit Item #

1 pc 676797046

1 pc 676797049

Retail Price

$ 388.70

$ 357.50

wedi Fundo Riolito neo Tileable | Cover Plate, Stainless Steel

Description wedi Fundo Riolito neo Tileable drain cover for 48” x 60” and 32” x 72” Riolito neo base

(1220 × 1524 mm and 813 × 1830 mm)

Width x Length x Height wedi Fundo Riolito neo Tileable drain cover for

36” x 60” and 48” x 72“ Riolito neo base (914

× 1524 mm and 1220 × 1830 mm)

1 5/8” × 43 1/4” × 3/4”

(41 × 1100 × 19 mm)

1 5/8” × 27 5/8” × 3/4”

(41 × 700 × 19 mm)

For tile installation heights of between 3/16” to 1”.

Reverse for thinner or thicker tile.

For Fundo Bases Riolito neo and Riolito neo Modular.

Unit Item #

1 pc 676797047

1 pc 676797050

Retail Price

$ 388.70

$ 357.50

wedi Fundo Discreto | System Component, for Creating Vertical Wall Drainage

Description External Dimensions

Length x Width x Height wedi Fundo Discreto

System Component Integrates into wedi seats, tileable cover included

31.5” × 2”

(800 × 51 mm)

For installation over wedi Fundo Riolito neo 48” x 60” or 32” x 60” bases

Unit Item #

1 pc 073738200

Retail Price

$ 998.00

wedi OneStep Shower System

Description wedi OneStep Shower Base wedi OneStep Shower Base wedi OneStep Shower Base wedi OneStep Shower Base wedi OneStep Shower / Tub Replacement Base wedi OneStep Shower / Tub Replacement Base

External Dimensions

Length × Width × Height

36” × 36” × 4”, center drain

(914 × 914 × 102 mm)

36” × 48” × 4”, center drain

(914 × 1220 × 102 mm)

32” × 60” × 4”, center drain

(813 × 1524 × 102 mm)

36” × 60” × 4”, center drain

(914 × 1524 × 102 mm)

36” × 60” × 4”, left drain

(914 × 1524 × 102 mm)

36” × 60” × 4”, right drain

(914 × 1524 × 102 mm)

Unit Item #

1 pc US4000004

1 pc US4000005

1 pc US4000008

1 pc US4000003

1 pc US4000006

1 pc US4000007

Retail Price

$ 698.00

$ 752.00

$ 856.00

$ 860.00

Custom Sizes available on request

wedi Curb Over

Description wedi Curb Over (Square Edges) wedi Curb Over (Square Edges)

Width x Length x Height Unit Item #

5” x 5’ x 4 1/2” (127 × 1524 × 114 mm) 1 pc US3000008

5” x 8’ x 4 1/2” (127 × 2500 × 114 mm) 1 pc US3000010

Retail Price

$ 80.57

$ 115.73

Installation over 2” x 4”’s construction. CAUTION: Do not allow Glass Door Assembly to penetrate Curb Over.

Description wedi Curb Full Foam (Square Edges) wedi Curb Full Foam (Square Edges) wedi Curb Full Foam (Square Edges)

Sloped on top surface

wedi Full Foam Curb

Width x Length x Height

5” x 3’ x 4 1/2”

(127 × 914 × 114 mm)

5” x 5’ x 4 1/2”

(127 × 1524 × 114 mm)

5” x 8’ x 4 1/2”

(127 × 2500 × 114 mm)

Unit Item #

1 pc

US3000011

074319002

1 pc 074319001

Retail Price

$ 58.55

$ 94.68

$ 138.84

wedi Full Foam Curb “LEAN“

Description wedi Full Foam Curb “LEAN“ (Square Edges) wedi Full Foam Curb “LEAN“ (Square Edges)

Width x Length x Height

2” x 5’ x 3 1/2”

(51 × 1524 × 89 mm)

2” x 8’ x 3 1/2”

(51 × 2438 × 89 mm)

Unit Item #

1 pc 074319007

Retail Price

$ 50.18

1 pc 074319008 $ 80.29

Sloped on top surface

Description wedi Shower Ramp *

* ADA compliant

wedi Shower Ramp

Width x Length x Height

12” x 5’, sloped 1 1/2” to 1/4”

(305 × 1524 mm, sloped 38.1 to 6.35 mm)

Unit Item #

1 pc 073736517

Retail Price

$ 223.73

wedi Niche | Square Edges

Description wedi Niche Square Edges wedi Niche Square Edges wedi Niche Square Edges wedi Niche Square Edges wedi Lean Combo Niche wedi Cathedral Niche

Dimension

16” × 8” (406 × 203 mm)

16” × 12” (406 × 305 mm)

16” × 16” (406 × 406 mm)

16” × 22” (406 × 559 mm) incl. removable shelf

16” × 42” (406 × 1067 mm) incl. 2 removable shelves

16” × 30” (406 × 762 mm) incl. removable shelf

Installation over 2” x 4”’s construction, 16” o.c. framework.

Dimensions are outside dimensions.

wedi Shower Seat M&L

Description Width x Length x Height wedi Seat M, Suspended Seat 17” x 17” (wall sides) x 4”

(432 × 432 × 102 mm) wedi Seat L, Suspended Seat 24” x 24” (wall sides) x 4”

(610 × 610 × 102 mm)

Unit Item #

1 pc US3000003

1 pc US3000004

1 pc US3000005

1 pc

US3000007

US3000024

US3000016

Retail Price

$ 52.53

$ 65.20

$ 67.24

$ 83.84

$ 144.77

$ 100.98

Unit Item #

1 pc

US3000001

US3000002

Retail Price

$ 139.00

$ 159.00

wedi Bench | Rectangular and Full Foam Triangular Seats

Description wedi Full Foam

Corner Seat

Width x Length x Height

23” × 23” (wall sides) × 20” sloped

(584 × 584 × 508 mm)

Unit

1 pc

Item #

073784101

Retail Price

$ 270.00

Rectangular bench made with 2” wedi Building Panel, full foam corner seat made of solid XPS foam.

These units are pre-made and ready for thinset installation against walls and feature a 1/8“ slope to the front.

wedi Sanoasa Bench 1

Description wedi Sanoasa Bench 1 M

Length x Height x Depth approx. 35” × 18” × 15” (900 × 454 × 380 mm)

Unit Item #

1 pc 076447030 wedi Sanoasa Bench 1 L approx. 47” × 18” × 15” (1200 × 454 × 380 mm) 1 pc 076447031

 The bench is delivered in four parts: Bench element, substructure element and 2 side elements

 wedi Joint Sealant is included for adhesion

 wedi Fiberglass Mesh Tape is included for the wall/floor connection

Retail Price

$ 505.47

$ 606.97

wedi Sanoasa Bench 2

Description Length x Height x Depth Unit Item # wedi Sanoasa Bench 2 M wedi Sanoasa Bench 2 L approx. 35” × 18” × 15” (900 × 454 × 380 mm) approx. 47” × 18” × 15” (1200 × 454 × 380 mm)

1 pc

076447032

076447033

 The bench is delivered in four parts: Bench element, substructure element and 2 side elements

 wedi Joint Sealant is included for adhesion

 wedi Fiberglass Mesh Tape is included for the wall/floor connection

Retail Price

$ 505.47

$ 606.97

wedi Sanoasa Bench 3

Description Length x Height x Depth Unit Item # wedi Sanoasa Bench 3 M wedi Sanoasa Bench 3 L approx. 35” × 18” × 15” (900 × 454 × 380 mm) approx. 47” × 18” × 15” (1200 × 454 × 380 mm)

1 pc

076447034

076447035

 The bench is delivered in four parts: Bench element, substructure element and 2 side elements

 wedi Joint Sealant is included for adhesion

 wedi Fiberglass Mesh Tape is included for the wall/floor connection

Retail Price

$ 505.47

$ 606.97

wedi Sanoasa Shower Bench 4

Description wedi Sanoasa Shower

Bench 4, straight

Length × Depth × Height

47 1/4” × 15” × 3 1/8”

(1200 × 380 × 80 mm)

Unit Item #

1 pc US3000000

Retail Price

$ 343.07

wedi Subliner Dry | Waterproofing and Crack-bridging Sheet Membrane

Description wedi Subliner Dry Mat

(waterproofing / Crack Iso) wedi Subliner Dry Mat

(waterproofing / Crack Iso) wedi Subliner Dry

Waterproof Sealing Tape wedi Mixing Valve

Flexi Collar wedi Flexi Collar, for sealing around

1/2“ to 3/4“ shower pipe protrusions

Subliner Dry Sealing Tape

Inside Corner

Subliner Dry Sealing Tape

Outside Corner

Width × Roll Length

39” × 16’

(1 × 5 m)

39” × 98’

(1 × 30 m)

5“ × 32.8’

(127 mm × 10 m)

Ø 5“

(Ø 127 mm)

4 3/4“ × 4 3/4“

(115 × 115 mm)

4 3/4“ × 4 3/4“ × 2 1/4“

(115 × 115 × 57.15 mm)

4 3/4“ × 4 3/4“ × 2 1/4“

(115 × 115 × 57.15 mm)

Unit

1 roll

1 piece

1 roll

Item #

US5000001

US5000005

US5000002

US5000000

US5000033

US5000007

Retail Price

$ 93.36

$ 523.38

$ 44.79

$ 15.36

$ 12.65

$ 15.00

1 roll US5000008 $ 15.00

Flexible waterproofing membrane for medium and high exposure wet areas – for interior walls / showers and steam showers.

wedi Joint Sealant | MS Polymer Sealant and Adhesive

Description wedi Joint Sealant,

MS polymer sealant wedi Joint Sealant,

MS polymer sealant

Contents

10 oz. (310 ml)

Unit

1 Cartridge

20 oz. (519.5 ml) 1 Sausage

Permanently flexible, waterproof sealant and adhesive for joint treatment.

Item #

US5000013

US5000010

Retail Price

$ 15.30

$ 25.44

wedi Sausage Gun | Gun for MS Polymer Sealant Sausages and Replacement Tips

Description wedi Sausage Gun, gun for wedi joint MS polymer sealant sausages wedi Sausage Gun Replacement Tip

Unit

1 piece per piece

Item #

US5000019

US5000020

Retail Price

$ 75.27

$ 1.05

Description wedi Fastener Kit

wedi Fastener Kit

Length Unit

100 wedi Coarse Thread Screws 1 5/8“

100 wedi Tab Steel Washers 1 piece

Item #

US5000070

Retail Price

$ 30.00

wedi Accessories | Coarse Thread Screws, Ceramic Coating

Description

Coarse thread screws, ceramic coating, for US markets only

Length

1 5/8” (41.5 mm)

Unit/Box

100 pcs

1000 pcs

Phillips head for wood studs, premium ceramic coating (ACQ Compliant)

Item #

US5000016

US5000012

Retail Price

$ 15.26

$ 88.33

wedi Accessories | Fine Thread Self Tapping Screws

Description

Fine thread self-tapping zinc coated

Length Unit/Box

1 1/4” (31.75 mm) 100 pcs

For metal framework with no risk of electric/galvanic corrosion. Phillips head.

Item #

US5000018

Retail Price

$ 21.08

wedi Accessories | Tab Steel Washers, Galvanized

Description

Tab Steel Washers,

Galvanized

Tab Steel Washers,

Galvanized

Washer, without tabs for flooring

Diameter

1 1/4” (31.75 mm)

Unit/Box

100 pcs

1000 pcs

Item #

US5000014

US5000009

Retail Price

$ 17.67

$ 134.86

1 1/4” (31.75 mm) 100 pcs US5000015 $ 17.67

Tabbed washers provide four tabs for fast and secure placement. wedi Washers provide a solid gauge according to

ISO standards and less potential for deformation. Load capabilities are independently tested.

wedi Accessories | Vapor Barrier

Description wedi Vapor Barrier

Unit

24 gallons

For use on building panel in steam room applications prior to tiling

0.24 gallon unit = 25 sq ft with a 20 mil (dry) thickness/film, (2 coats,10 mil dry each)

Item #

US5000051

Retail Price

$ 60.64

• Hospitality

• Health Care

• Universities

• Dormitories wedi Custom Wellness & Spa Design Solutions

Starting a new custom project, residential or commercial steam room? Do you need custom loungers? From idea to installation, you have our promise wedi will support you right from the start. The moment you contact us, our team springs into action. We generate custom CAD drawings based upon your ideas and plans. We produce custom products fabricated from impermeable extruded polystyrene foam material exclusively for steam showers and wetrooms. We test all the assemblies to ensure everything works flawlessly before we supply you with all the components, ready to install.

We understand products are just part of the project. That’s why we create and work in tandem with your lighting concepts, heating systems and preferred shower technologies.

wedi is at your side – in all areas, at all times.



Your idea

– As you envision your wellness concept, contact wedi and we can help bring your idea to life.



We plan together

– wedi provides integrated project planning to ensure all components, shower technologies, drains and supply pipes are incorporated into your vision and unified for proper performance.



Made-to-measure products

– With your approval, we produce solutions that fit your specifications and requirements perfectly. Then we assure the system measures up in terms of performance through trial assemblies at our factory all prior to shipping.



On time delivery

– We deliver all prefabricated components on time and in their entirety, with complete step-by-step assembly instructions so you can take your idea and bring it to life!

01 02

wedi is a proud member of:

Serving USA, Canada, Australia & New Zealand

Made in

Germany wedi Corporation

Tel. +1-847-357-9815

Fax. +1-847-357-9819 [email protected] www.wedicorp.com

Made in USA

Did you know?

Great quality installation results depend on not only having great products to use – the Know-How and Experience in how to use them is key too. wedi trained and certified all Baeumler

Quality Construction installers in my team and now they fully know and appreciate what they can achieve with wedi.

This educational service is offered to all professional contractors of all trades and wedi‘s local Technical Sales Support Managers come out on site and install with you when you do your first wedi shower installation. Your peace of mind – at no charge.

Just a call away!

Be sure to ask for:

Certified wedi Installer wedi-quality and performance certified by:

0799 (System 2+) wedi GmbH

Hollefeldstraße 51

48282 Emsdetten

0799-CPD-132

DoP 0001

ETA-13/0385

ETAG 022 Teil 3

Bausatz mit wasserdichten Platten und weiteren Komponenten zur

Herstellung einer Abdichtung unter einer Nutzschicht für die

Verwendung in innen liegenden

Nassbereichen

Klassifizierung des Systems und deklarierte Produkt- und Systemeigenschaften siehe Anhang 1 der

ETA-13/0385

US

Hello! I am an AI chatbot specifically trained to assist you with the wedi US3000005 Specification. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant is out of keyboard. Please, try again later.