Frigidaire FHPC132AB1 19" Portable Air Conditioner Installation instructions

Important Safety Instructions..............................2-3

Product Registration...............................................4

Normal Sounds.......................................................4

Unit Description......................................................5

Accessories Included.............................................5

Installation Instructions.......................................6-7

Air Conditioner Features.....................................8

Operating Instruction......................................8-17

Care and Cleaning.............................................18

Before You Call..................................................19

Major Appliance Limited Warranty................. ...20

Important Safety Instructions

NOTE:

NOTE: WARNING

WARNING

WARNING

WARNING

SAFETY PRECAUTIONS

Important Safety Instructions

SAFETY PRECAUTIONS

Provide ventilation per installation instructions.

Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make units run excessively.

NOTE:

fails manufacturer.

manufacturer.

CAUTION

• This appliance is not intended for use by persons (including children) with reduced physical ,sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• The appliance shall be installed in accordance with national wiring regulations.

• The appliance shall not be installed in the laundry rooms.

Product Registration & Normal Sounds

Product Registration

Record Your Model and Serial Numbers

3FDPSEJOUIFTQBDFQSPWJEFECFMPXUIFNPEFBOETFSJBMOVNCFST0OBMMNPEFMTUIF

TFSJBMQMBUFJTMPDBUFEPOUIFTJEFPGUIFDBCJOFU

Model No.

Serial No.

Register Your Product

5IFTFMGBEESFTTFE130%6$53&(*453"5*0/$ "3%TIPVMECFGJMMFEJODPNQMFUFMZ

TJHOFEBOESFUVSOFEUPUIF'SJHJEBJSF$PNQBOZ

Normal Sounds

Sound of Rushing Air

"UUIFUPQPGUIFVOJUZPVNBZ

IFBSUIFTPVOEPGSVTIJOHBJS

CFJOHNPWFECZUIFGBO

High pitched Chatter

5PEBZTIJHIFGGJDJFODZ

DPNQSFTTPSTNBZIBWFB

IJHIQJUDIFEDIBUUFSEVSJOH

UIFDPPMJOHDZDMF

Gurgle/Hiss i(VSHMJOHPSIJTTJOHwOPJTFNBZCF

IFBSEEVFUPSFGSJHFSBOUQBTTJOH

UISPVHIFWBQPSBUPSEVSJOHOPSNBM

PQFSBUJPO

Vibration

6OJUNBZWJCSBUFBOENBLFOPJTF

CFDBVTFPGVOFWFOGMPPS

Unit Description & Accessories Included

Unit Description

Air Outlet Grill

Signal

Receiver

Remote

Control

Control Panel

Carrying

Handle

Air

Exhaust

Continuous

Drain Outlet

Power

Cord

Air Intake

Bottom

Drain Outlet

Heat Pump Drain

Outlet (for heat pump model)

Castor

Accessories Included

PARTS: QUANTITY: PARTS NAME:

Window Kit Connector A

Exhaust hose connector B

Window Kit

Exhaust Hose

Screws

Safety Lock

Bolts

Foam seal A

Foam seal B

Remote Control

Battery

Drain hose

Drain hose and connector

(for heat pump model)

( )

+

( )

(78.7"(2m))

Installation Instructions

Installation Instructions

EXHAUSTING HOT AIR

In the Cool Mode the appliance must be placed close to a window or opening so that the warm exhaust air can be ducted outside.

First position unit on a flat floor and is within the vicinity of a single circuit outlet power source. Make sure there’s a minimum of 31.5" clearance in the front/back of the unit, and a minimum of 19.7" clearance in the left/right sides of the unit.

1. Extend both side of the exhaust hose(Fig.1)

2. Install the connector B into the unit (Fig.2).

3. Affix the connector A into the window slider kit and seal.(Fig.3&4)

19.7"

1 Slide onto

2 Lock

Extend the side of hose

Fig.1

Fig.2

Vertical window

Horizontal window

Window Slider Kit

Minimum:26.6 (67.5cm)

Maxmum:52.5 (133cm)

Window Slider Kit

Minimum:26.6 (67.5cm)

Maxmum:52.5 (133cm)

Fig.3

Fig.4

The hose can be extended from its original length of 15"up to 59",but it is the best to keep the length to minimum required. Also make sure that the hose does not have any sharp bends or sags.(Fig.5)

Fig.5

31.5"

Installation Instructions

Installation Instructions(continued)

Installation in a double-hung sash window

1.Cut the foam seals A(adhesive type) to the proper lengths and attach them to the window and stool.(Fig.6)

2.Open the window sash and place the window slider kit on the window stool (Fig.7). Attach the window slider kit to the window stool. Adjust the length of the window slider kit according to the width of window.

Screw down the two screws on the window slider kit. See Fig.7.

Cut the adjustable window slider kit if the width of window is less than

26.6 inches(Fig.8).

3.Close the window sash securely against the window slider kit.(Fig.9)

4.Drive two 1/2 screws to secure the window slider kit to the window sash.(Fig.9)

5.Secure the window slider kit to the window stool(Fig.9):

A: For wooden window: Use 3/4 screws for securing.

B: For Vinyl-Clad windows: Use 1/2 hex head cap screws for securing.

6.To secure lower sash in place, attach right angle sash lock with 1/2

(12.7mm) screw as shown(Fig.10).

NOTE: It is difficult to lock the windows with the sash lock for Vinyl-Clad windows, so you can use lock by window itself.

7.Cut the foam seal B to an appropriate length and seal the open gap between the top window sash and outer window sash, as shown in

Fig.11.

screws

Window slider kit

Foam seal B

Fig.10

Fig.11

screws or hex head cap screws

Window stool

Fig.9

Installation in a sliding sash window

1.Cut the foam seals A(adhesive type) to the proper lengths and attach them to the window frame. See Fig.12.

2.Open the window sash and place the window slider kit on the window stool (Fig.13). Attach the window slider kit to the window stool. Adjust the length of the window slider kit according to the height of window.

Screw down the two screws on the window slider kit. See Fig.13.

Cut the adjustable window slider kit if the height of window is less than

26.6 inches(Fig.8).

3.Close the window sash securely against the window slider kit.(Fig.14)

4.Drive two 1/2 screws to secure the window slider kit to the window sash.(Fig.14)

5.Drive two 3/4 screws to secure the window slider kit to the window stool.(Fig.14)

6.Cut the foam seal B to an appropriate length and seal the open gap between the sliding sash and outer window sash, as shown in Fig.15.

7.To secure sliding sash in place, attach right angle sash lock with 1/2

(12.7mm) screw as shown(Fig.16).

Foam seal A

(adhesive type)

Fig.6

screws

Window slider kit

26.6"~52.5"

Window stool

Cut this to fit your window

Fig.7

Fig.8

Foam seal A

(adhesive type)

Fig.12

Window slider kit

Window stool screws

26.6"~52.5"

Fig.13

Window stool Window slider kit screws screws

Fig.14

Foam seal B

Fig.15

Fig.16

Air Conditioner Features & Operating Instructions

Control Panel

%JTQMBZ5FNQFSBUVSF5JNFS

°C

°F

4XJOH 5JNFS 4MFFQ .PEF

4FMFDUJPO

"EKVTU

5FNQFSBUVSF

PS5JNFS

/PUFiIFBUwNPEFJTGPSIFBUDPPMNPEFMTPOMZ

'BO

4QFFE

'JMUFS

3FTFU

1PXFS

RQÂRII

Operating Instruction

Cool mode

1SFTTUIFiNPEFwCVUUPOVOUJMUIF$PPMNPEFJOEJDBUPSMJHIUT

1SFTTUIFGBOTQFFECVUUPOUPDIPPTFUIFGBOTQFFEBDDPSEJOHUPUIFJMMVNJOBUJPOPGUIFGBOTQFFEJOEJDBUPS

:PVDBODIPPTFUIFiIJwiNFEwiMPXwPSiBVUPwGBOTQFFETFUUJOH

1SFTTUIFiwPSiwCVUUPOUPDIPPTFUIFUFNQFSBUVSFZPVXBOU

°C

°F

Operating Instructions

Dry mode

Press the “mode” button until the Dry mode indicator lights. In this mode, the “ ” or “ ” button is disabled and the screen displays the room temperature. The unit will continuously drain moisture from the room.

Note: In this mode, the fan speed will be set as “low” automatically, which cannot be changed.

In this mode, condensate drainage are required, refer to the "Drainage Instructions" on Page 16-17 for more instructions to drain the excess condensate.

°C

°F

Fan mode

Press the “mode” button until the Fan mode indicator lights.

In this mode, you can select fan speed “hi”, “med” or “low”.

The screen displays room temperature.

Note: In this mode, the air exhaust hose does not need to be connected.

°C

°F

Heat mode(For Heat & Cool models only)

Press the “mode” button until the Heat mode indicator lights.

Press the “ ” or “ ”button to choose the temperature you want.

Press the "fan speed" button to choose the fan speed according to the illumination of the fan speed indicator.

You can choose the “hi”, “med”, “low”, or “auto” fan speed setting.

Note: The unit have a build in condensate pump to pump out the excess condensate during heating mode.

Condensate drainage are required, refer to the "Drainage Instructions" on Page 16-17 for more instructions to drain the excess condensate.

°C

°F

Operating Instructions

AUTO mode

Press the “mode” button until the AUTO mode indicator lights.

Press the “ ” or “ ” button to choose the temperature you want. The screen will display the setting temperature.

In this mode, the unit will automatically select cooling, heating(not applicable for cooling only models), or fan only operation depending on what temperature you have selected and the room temperature. The air conditioner will control room temperature automatically round the temperature point set by you.

Note: In this mode, fan speed cannot be selected.

°C

°F

Timer mode

The timer facilitates the user to delay the unit startup or shutdown.

How to delay startup

Plug in the unit, so the unit turns to standby.

Press the “timer” button, then the Timer indicator and number of hours on the screen will light.

Tap or hold the UP arrow ( ) or the DOWN arrow ( ) to change delay start timer at 0.5 hour increments up to 10 hours, then at 1 hour increments up to 24 hours.

After 5 seconds, the setting will be confirmed automatically and the control will count down the time remaining until startup.

The unit will start up in the mode as previously set. Press the “timer” button again within 5 seconds, you will quit the timer setting directly.

To cancel the setting, press the “timer” button again will show the remain time and press the button again to quit the function.

°C

°F

How to delay shutdown

You can delay shutdown when the unit is on.

Press the “timer” button, then the Timer indicator and number of hours on the screen will light.

Tap or hold the UP arrow ( ) or the DOWN arrow ( ) to change delay shutdown timer at 0.5 hour increments up to 10 hours, then at 1 hour increments up to 24 hours.

After 5 seconds, the setting will be confirmed automatically and the control will count down the time remaining until shutdown. Press the “timer” button again within 5 seconds, you will quit the timer setting directly.

To cancel the setting, press the “timer” button again will show the remain time and press the button again to quit the function.

°C

°F

Operating Instructions

Sleep mode

When the unit is in Cool, Heat or Auto mode, you can press the “sleep” button to make the unit run in Sleep mode.

In this mode, the fan speed will be set as “auto” automatically, which cannot be changed.

In Cool/Heat mode the selected temperature will increase/decrease by 2 °F 30 minutes after the mode is selected.

The temperature will then increase/decrease by another 2 °F after an additional 30 minutes. This new temperature will be maintained for 7 hours before it returns to the originally selected temperature. This ends the "Sleep" mode and the unit will continue to operate as originally programmed.

The "Sleep" mode program can be cancelled at any time during operation by pressing the "Sleep", “mode”, “fan speed” or “on·off” button.

Note: In Fan or Dry mode, Sleep mode cannot be set.

During Sleep mode the brightness of the indicators will reduce by half.

°C

°F

Louver Swing Function

Press the “swing” button to enable louver swing function, the swing indicator will illuminate and the louver on the top panel will swing up and down. Press this button again to disable the louver swing function.

°C

°F

Filter reset

This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more efficient operation.

The filter indicator will illuminate after 250 hours of fan operation. Press the “filter reset” button, to reset after cleaning

the filter.

°C

°F

function

Press the “ ” and “ ”button the same time for more than 3 seconds to switch between degree Fahrenheit and degrees Celsius.

Note: Under Dry/Fan mode, you can not select °F/°C.

Operating Instructions

Remote Control

Cool Only models

3FNPUF$POUSPMTDSFFO

5FNQ5JNFSTFUUJOHCVUUPO

.PEFCVUUPO

5JNFSCVUUPO

Heat and Cool models

RQÂRIIEXWWRQ

'BO4QFFECVUUPO

4XJOHCVUUPO

4MFFQCVUUPO

Battery Installation and Important Instructions

3FNPWFUIFDPWFSBUUIFCBDLPGUIFSFNPUFDPOUSPM

*OTFSUUIFQSPWJEFECBUUFSJFTDPSSFDUMZ TFFUIFJOTUSVDUJPOT

JOTJEFUIFCBUUFSZDPNQBSUNFOU

$MPTFVQUIFDPWFS

5PSFQMBDFUIFPMECBUUFSJFT XIJDIIBWFCFFOVTFEVQ

XJUIUXPOFX3i"""w7CBUUFSJFTSFQFBUUIF

TUFQTBCPWF

'JH

*GUIFSFNPUFDPOUSPMVOJUJTSFQMBDFEPSEJTDBSEFEUIFCBUUFSJFTNVTUCFSFNPWFEBOEEJTQPTFEPGJO

BDDPSEBODFXJUIMPDBMMFHJTMBUJPOBTUIFZEPIBSNUPUIFFOWJSPONFOU

%POPUNJYPMEBOEOFXCBUUFSJFT

%POPUNJYBMLBMJOFTUBOEBSE DBSCPO[JODPSSFDIBSHFBCMF OJDLFMDBENJVNCBUUFSJFT

%POPUEJTQPTFPGCBUUFSJFTJOGJSF#BUUFSJFTNBZFYQMPEFPSMFBL*GUIFSFNPUFDPOUSPMJTOPUVTFEGPSB

MPOHUJNFSFNPWFUIFCBUUFSJFTGSPNUIFSFNPUFDPOUSPM

5IFSFNPUFDPOUSPMNVTUCFIBOEMFEXJUIFYUSFNFDBSF%POPUESPQJUPSFYQPTFJUUPEJSFDUTVOMJHIU

PSTPVSDFTPGIFBU

5IJTEFWJDFDPNQMJFTXJUI1BSUPGUIF'$$3VMFT0QFSBUJPOJTTVCKFDUUPUIFGPMMPXJOHUXPDPOEJUJPOT

5IJTEFWJDFNBZOPUDBVTFIBSNGVMJOUFSGFSFODFBOE UIJTEFWJDFNVTUBDDFQUBOZJOUFSGFSFODF

SFDFJWFEJODMVEJOHJOUFSGFSFODFUIBUNBZDBVTFVOEFTJSFEPQFSBUJPO

6TFS

'JH

1PSUBCMF"$ 1PJOUUIFSFNPUFDPOUSPMBUUIFMPDBUJPOPGUIFTJHOBMSFDFJWFS

5IFSFNPUFDPOUSPMNVTUCFOPNPSFUIBOGU NFUFST

BXBZGSPNUIFVOJU XJUIPVUPCTUBDMFTCFUXFFOUIFSFNPUF

DPOUSPMBOEUIFVOJU

3FNPUF$POUSPM

Operating Instructions

How to Use the Remote Control

TURNING THE UNIT ON

Plug in the unit, then press the “on·off” button (when turned on, the unit will operate as the last setting before shutdown.

To switch the unit off, press “on·off” button again, then remove the plug.

Do NOT switch the unit off by removing the plug.

Always switch the unit off by pressing the “on·off” button and wait for few minutes before removing the plug.

Cool mode

Press the “mode” button until the left side of LCD screen displays “cool”.

Press the “ fan speed” button to choose the fan speed

“auto”, “high”, “mid”, and “low”.

Press the “ ” and “ ”button to choose the temperature you want.

Dry mode

Press the “mode” button until the left side of LCD screen displays “dry”.

In this mode, the “ ” or “ ” button is disabled and the screen will remain blank. The unit will continuously drain moisture from the room.

Note:

In this mode, the fan speed will be set as “low” automatically, which cannot be changed.

In this mode, condensate drainage are required, refer to the

"Drainage Instructions" on Page 16-17 for more instructions to drain the excess condensate.

Fan mode

Press the “mode” button until the left side of LCD screen displays “fan”.

In this mode, you can select fan speed “high”, “mid”, “low” by pressing the Fan speed button and referring to the diagram.

Note: In this mode, the air exhaust hose does not need to be connected.

Operating Instructions

Heat mode(For Heat & Cool models only)

Press the “mode” button until the left side of LCD screen displays “heat”.

Press the “ ” and “ ” button to choose the temperature you want.

Press the “ fan speed” button to choose the fan speed

“auto”, “high”, “mid”, and “low”.

Note: In this mode, condensate drainage are required, refer to the

"Drainage Instructions" on Page 16-17 for more instructions to drain the excess condensate.

Auto mode

Press the “mode” button until the left side of LCD screen displays “auto”.

Press the “ ” and “ ” button to choose the temperature you want.

In this mode, the unit will automatically select cooling, heating(not applicable for cooling only models), or fan only operation depending on what temperature you have selected and the room temperature. The air conditioner will control room temperature automatically round the temperature point set by you.

Note: In this mode, fan speed cannot be selected.

Sleep mode

When the unit is in Cool, Heat or Auto mode, you can press the “sleep” button to make the unit run in Sleep mode. In this mode, the fan speed will be set as “auto” automatically, which cannot be changed.

In Cool/Heat mode the selected temperature will increase/decrease by 2 °F 30 minutes after the mode is selected. The temperature will then increase/decrease by another 2 °F after an additional 30 minutes. This new temperature will be maintained for 7 hours before it returns to the originally selected temperature. This ends the

"Sleep" mode and the unit will continue to operate as originally programmed.

The "Sleep" mode program can be cancelled at any time during operation by pressing the "Sleep", “mode”, “fan speed” or “on·off” button.

Note: In Fan or Dry mode, Sleep mode cannot be set.

Louver Swing Function

Press the “swing” button to enable louver swing function, and the upper side of screen will display “ ”. The louver on the top panel will swing up and down.

Press this button again to disable the louver swing function.

Fig.19

Operating Instructions

function

Press the “ ” and “ ”button the same time for more than 3 seconds to switch between degree Fahrenheit and degrees Celsius.

Note: Under Dry/Fan mode, you can not select °F/°C.

Timer mode

How to delay startup

Plug in the unit, so the unit turns to standby.

Press the “timer” button, when the unit is off. The screen will display “timer” and “h”, and the “on” will flashing. Tap or hold the UP arrow " " or the DOWN arrow " " to change delay start timer at 0.5 hour increments up to 10 hours, then at 1 hour increments up to 24 hours. After 3 seconds, the timer function is enabled, then

“on” will stop flashing, the display will show the temperature back and the control will count down the time remaining until startup. The unit will start up in the mode as previously set.

To cancel the setting, press the “timer” button again. You can also cancel the setting by pressingthe “on·off” button.

How to delay shutdown

You can delay shutdown when the unit is on.

Press the “timer” button, when the unit is on. The screen will display “timer”and “h”, and the “off ” will flashing. Tap or hold the UP arrow “ ” or the DOWN arrow “ ” to change delay shutdown timer at 0.5 hour increments up to 10 hours, then at 1 hour increments up to 24 hours. After 3 seconds, the timer function is enabled, then

“off ” will stop flashing, the display will show the temperature back and the control will count down the time remaining until shutdown.

To cancel the setting, press the “timer” button again. You can also cancel the setting by pressingthe “on·off” button.

Fault Code

If the screen on the unit displays

“AS”, the room temperature sensor has failed. Contact your Authorize

Frigidaire Service Center.

If the screen on the unit displays

“ES”, the pipe temperature sensor has failed. Contact your Authorize

Frigidaire Service Center.

If the display reads "E4" , the communication between display PCB and main control PCB is faulty. Contact your Authorized Frigidaire

Service Center.

If the screen on the unit displays “P1”, the water collection tank inside the unit should be full.

Refer to the "Drainage Instructions" on Page

16-17 for more instructions to drain the successive condensate. If error repeats, contact your Authorize Frigidaire Service Center.

Operating Instructions

Drainage Instructions

Continuous Drainage

During the Dry mode, you will need a garden hose (sold separately) to drain the condensate from the unit.

Follow the steps below:

Unscrew the drain cap of continuous drain outlet(Fig.20).

Connect one end of the garden hose (sold separately) to the drain outlet then lead the other end into a drain that is lower than the unit(Fig.21).

Figure 20 Figure 21

Garden hose

Drain cap for DRY mode

NOTE

Condensate may flow out after removing the drain cap, if the unit is running in Cool or Auto mode.

When you want to remove the garden hose, prepare a drip tray (not supplied) to collect the condensate from the drain outlet.

Please be sure that the height of the drain and section of the drain hose should not be higher than that of the drain outlet, or the continous drainage may not work properly.

During Cool or Auto mode, it is recommended to disable continuous drainage by replacing the drain cap to the drain outlet, to reach the maximum performance.

Heat pump Drainage(For heating & cooling model only)

During the Heat mode, you will need a 1/4" drainage hose (packed with the unit) to drain the condensate from the unit.

Follow the steps below:

Unscrew the heat pump drain cap and rubber of heat pump drain outlet(Fig.22).

Insert the rubber head into the outlet. Then screw the sealing cap into the heat pump drain outlet(Fig.23).

Lead the other end of the 1/4" drainage hose to a drain that is not 16ft(5m) higher than the heat pump drain outlet.

Figure 22 Figure 23

Heat pump drain cap

1

2 heat pump drain outlet rubber head sealing cap

Operating Instructions

Drainage Instructions

NOTE:

There is a 1/4” hole on the window kit for leading the drainage hose outside during the heating mode.

Do not drain condensate outside when outside temperature is below 32°F (0°C).

Figure 24

Window slider kit

1/4" hole

Emptying the condensate residue inside the unit during winter storage.

Put a drip tray (not supplied) under the continuous drain outlet, then unscrew the drain cap to allow the condensate to flow into the drip tray. Replace the drain cap to the continuous drain outlet when no condensate flows out.

Put the drip tray under the bottom drain outlet, then remove the rubber stopper from the drain outlet, to allow the condensate to flow into the drip tray. If your drip tray can’t hold all the condensate, a number of fills will be needed.

Replace the drain cap to the bottom drain outlet when no condensate flows out.

Figure 25

Note: To ensure all condensate residue has been removed, tilt the unit by lifting it slightly upwards from the front until no more condensate comes out from the drain outlet.

Drip tray

Bottom

Drain Outlet

Care and Cleaning

Cleaning

Clean your air conditioner occasionally to keep it looking new.

Be sure to unplug the unit before cleaning to prevent shock or fire hazards.

CLEANING THE UNIT

The cabinet and front may be dusted with an oil-free cloth or washed with a cloth dampened in a solution of warm water and mild liquid dishwashing detergent.

Never use harsh cleaners, wax or polish on the cabinet front.

Be sure to wring excess water from the cloth before wiping around the controls. Excess water in or around the controls may cause damage to the air conditioner.

CLEANING THE FILTERS

To keep your air conditioner working efficiently, you should clean the filters every week of operation.

This unit has two filters, they are filter A and B. Grasp the upper panel tab and take off the filter A which behind the grill of the back panel (Fig.25).

Remove the lower filter B by loosening the screw. Take down the air inlet grille, then remove the air filter as shown in Fig.25.

Wash the filter using liquid dishwashing detergent and warm water.

Rinse filter thoroughly. Gently shake excess water from the filter. Be sure filter is thoroughly dry before replacing.

Or, instead of washing you may vacuum the filter clean.

Replace the filter after the filter is dry.

Remove screw

Take down filter

Figure 25

Winter Storage

If the air conditioner will not be used for an extended period of time:

1.Drain the water collection tank completely and leave the bottom drain cap and rubber plug long time enough to allow any residual water to drain out. Once the tank is completely drained and no more water flows out, reinstall the rubber plug and cap.

2.Remove and clean the filter, allow it to dry completely, then reinstall it.

3.Remove the batteries from the remote control.

4.Store the air conditioner in a cool, dry location, away from direct sunlight, extreme temperature, and excessive dust.

Before using the air conditioner again:

1.Make sure the filter and drain cap are in place.

2.Check the cord to make sure it is in good condition, without cracks or damage.

3.Place new batteries in the remote control.

4.Install the air conditioner as described in the

Installation Instructions.

Before You Call

2009 Electrolux Home Products, Inc.

All rights reserved.

19

Major Appliance Limited Warranty

Your appliance is covered by a limited one-year warranty for functional repairs only. For one year from your original date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions. After one year from your original date of purchase, the consumer will be responsible for diagnostic, labor and parts costs as well as any removal, transportation and reinstallation expenses which are incurred during service on components.

Exclusions This warranty does not cover the following:

1. Products with original serial numbers that have been removed, altered or cannot be readily determined.

2. Product that has been transferred from its original owner to another party or removed outside the USA or

Canada.

3. Rust on the interior or exterior of the unit.

4. Products purchased "as-is" are not covered by this warranty.

5. Food loss due to any refrigerator or freezer failures.

6. Products used in a commercial setting.

7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not in ordinary household use or used other than in accordance with the provided instructions.

8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.

9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc., which are not a part of the appliance when it is shipped from the factory.

10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs, handles, or other cosmetic parts.

11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip charges, or mileage expense for service calls to remote areas, including the state of Alaska.

12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors, cabinets, walls, etc.

13. Damages caused by: services performed by unauthorized service companies; use of parts other than genuine Electrolux parts or parts obtained from persons other than authorized service companies; or external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR

REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST

PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR

CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES

RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME

STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE-

QUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS

OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.

YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.

If You Need

Service

Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.

Service under this warranty must be obtained by contacting Electrolux at the addresses or phone numbers below.

This limited warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances

North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp.

Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under this warranty must be performed by Electrolux or an authorized service company. Product features or specifications as described or illustrated are subject to change without notice.

USA

1.800.944.9044

Electrolux Major Appliances

10200 David Taylor Drive

Charlotte, NC 28262

20 2009 Electrolux Home Products, Inc.

Canada

1.800.265.8352

Electrolux Canada Corp.

5855 Terry Fox Way

Mississauga, Ontario, Canada

L5V 3E4

All rights reserved.