Frigidaire FFPW12C2R11 Portable Air Conditioner Owner's Manual

All about the

Use & Care

of your

Portable Air Conditioner

TA B L E O F C O N T E N T S

Product Registration .............................................

4

Normal Sounds .................................................... 4

Unit Description ................................................... 5

Accessories Included ............................................

5

Installation Instructions ........................................

6-7

Conditioner ......................................

8

Operating Instructions

Care and Cleaning

Before You Call ................................................... 12

Major Appliance Limited Warranty ........................ 13 www.frigidaire.com USA 1-800-944-9044 www.frigidaire.ca Canada 1-800-265-8352

Important Safety Instructions

NOTE:

This USE & CARE MANUAL provides specific operating instructions for your model. Use the portable air conditioner only as instructed in this USE & CARE MANUAL. These instructions are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating, and maintaining any appliance.

NOTE:

The power supply cord with this air conditioner contains a current detection device designed to reduce the risk of fire.

Please refer to the section ‘Operation of

Current Device’ for details.

In the event that the power supply cord is damaged, it cannot be repaired. It must be replaced with a cord from the product manufacturer.

WARNING

Avoid fire hazard or electric shock. Do not use an extension cord or an adaptor plug. Do not remove any prong from the power cord.

Grounding type wall receptacle

Do not, under any circumstances, cut, remove, or bypass the grounding prong.

WARNING

For Your Safety

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Read product labels for flammability and other warnings.

WARNING

Prevent Accidents

To reduce the risk of fire, electrical shock, or injury to persons when using your air conditioner, follow basic precautions, including the following:

Be sure the electrical service is adequate for the model you have chosen. This information can be found on the serial plate, which is located on the side of the cabinet.

If the air conditioner is to be installed in a window, you will probably want to clean both sides of the glass first.

Be sure the air conditioner has been securely and correctly installed according to the installation instructions in this manual. Save this manual for possible future use in removing or reinstalling this unit.

Power supply cord with 3-prong grounding plug and current detection device

WARNING

Electrical Information

The complete electrical rating of your new protable air conditioner is stated on the serial plate. Refer to the rating when checking the electrical requirements.

Be sure the air conditioner is properly grounded. To minimize shock and fire hazards, proper grounding is important. The power cord is equipped with a three-prong grounding plug for protection against shock hazards.

Your air conditioner must be used in a properly grounded wall receptacle. If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker, have a qualified electrician install the proper receptacle.

Do not run air conditioner without outside protective cover in place. This could result in mechanical damage within the air conditioner.

Do not use an extension cord or an adapter plug.

SAFETY PRECAUTIONS

DANGER! Avoid Serious Injury or Death

This air conditioner contains no user-serviceable parts. Always call an authorized Electrolux servicer for repairs.

Do not insert or place fingers or objects into the air discharge area on top of the unit.

Do not start or stop the air conditioner by unplugging the power cord or turning off the power at the electrical box.

Do not cut or damage the power cord.

If the power cord is damaged, it should only be replaced by an authorized Electrolux servicer.

In the event of a malfunction (sparks, burning smell, etc.), immediately stop the operation, disconnect the power cord, and call an authorized

Electrolux servicer.

Do not operate the air conditioner with wet hands.

Do not pull on the power cord.

Do not drink any water that is drained from the air conditioner.

2 2009 Electrolux Home Products, Inc.

All rights reserved.

Important Safety Instructions

SAFETY PRECAUTIONS

CAUTION! Avoid Injury or damage to the unit or other property

Provide occasional ventilation during use. Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make units run excessively.

Do not climb on or place objects on the unit.

Do not hang objects off the unit.

Do not place containers with liquids on the unit.

Turn off the air conditioner at the power source when it will not be used for an extended period of time.

Periodically check the condition of the unit’s installation accessories for any damage.

Do not apply heavy pressure to the radiator fins of the unit.

Operate the unit with air filter in place.

Do not block or cover the intake grille, discharge area and outlet ports.

Ensure that any electrical/electronic equipment is one yard away from the unit.

Do not use or store flammable gases near the unit.

READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER.

Unit must be upright for one hour prior to operating.

Plug in & press RESET

The power supply cord contains a current device that senses damage to the power cord. To test your power supply cord do the following:

Plug in the Air Conditioner.

The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will notice a click as the RESET button pops out.

Press the RESET button. Again you will notice a click as the button engages.

The power supply cord is now supplying electricity to the unit. (On some model, this is also indicated by a light on the plug head)

NOTE:

Do not use this device to turn the unit on or off.

Always make sure the RESET button is pushed in for correct operation.

The power supply cord must be replaced if it fails to reset when either the TEST button is pushed, or it cannot be reset. A new one can be obtained from the product manufacturer.

If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one obtained from the product manufacturer.

2009 Electrolux Home Products, Inc.

All rights reserved.

3

Product Registration & Normal Sounds

Product Registration

Record Your Model and Serial Numbers

Record in the space provided below the model and serial numbers. On all models, the serial plate is located on the side of the cabinet.

Model No.

Serial No.

Register Your Product

The self-addressed PRODUCT REGISTRATION CARD should be filled in completely, signed and returned to the Frigidaire Company.

Normal Sounds

Sound of Rushing Air

At the front of the unit, you may hear the sound of rushing air being moved by the fan.

Gurgle/Hiss

“Gurgling or hissing” noise may be heard due to refrigerant passing through evaporator during normal operation.

High pitched Chatter

Today’s high efficiency compressors may have a high pitched chatter during the cooling cycle.

Vibration

Unit may vibrate and make noise because of uneven floor.

4

2009 Electrolux Home Products, Inc.

All rights reserved.

Unit Description & Accessories Included

Unit Description

ROOM AIR DISCHARGE

CARRYING HANDLE

(BOTH SIDES)

CONTROL PANEL

REMOTE SIGNAL

RECEIVER

EXHAUST

AIR OUTLET

AIR INTAKE

DEHUMIDIFYING

DRAIN OUTLET

DUCTED AIR INLET

REMOTE CONTROL

INDOOR AIR

INLET SWITCH

CASTOR

Fig. 1

BOTTOM TRAY DRAIN OUTLET

Accessories Included

PARTS: PARTS NAME:

Adaptor A( To window kit )

Window Hose Kit(Hose and Adaptor B)

QUANTITY:

2 pcs

2 set

Window Sliding Kit

Foam Seal

Remote Control

Battery(For remote control)

12.7mm Screw

19mm Screw

12.7mm Hex Head Cap Screw

Safety Lock

Fig. 2

Check all the accessories are included in the package and please refer to the installation instructions for their usage.

2009 Electrolux Home Products, Inc.

All rights reserved.

1 set

3 pcs

1 pc

2 pcs

4 pcs

2 pcs

2 pcs

1 pc

5

Installation Instructions

Installation Instructions

HOSES INSTALLATION

In the COOLING Mode the appliance must be placed close to a window or opening so that the air outside could be ducted inside the unit and the warm exhaust air can be ducted outside.

First position unit on a flat floor and make sure there’s a minimum of 30.5cm clearance around the unit, and is within the vicinity of a single circuit outlet power source.

1. Take out the hoses from the package.

2. Extend the other end(without adaptor) of the hoses (Fig. 3)

and screw it to adaptor A (Fig. 4) .

3. Slide the hose assemblies onto the unit (Fig. 5).

4. Affix the adaptor A into the window slider kit and seal. (Fig. 6&7)

Vertical window

Window Slider Kit

Minimum:67.5cm(26.6")

Maxmum:123cm(48.5")

Fig. 6

Slide onto

Extend the end of hose

Fig. 3

Fig. 4

Slide onto

Fig. 5

Horizontal window

Window Slider Kit

Minimum:67.5cm(26.6")

Maxmum:123cm(48.5")

Fig. 7

The hose can be extended from its original length of 38.1cm up to

149.9cm, but it is the best to keep the length to minimum required. Also make sure that the hose does not have any sharp bends or sags. (Fig. 8 )

Fig. 8

6 2009 Electrolux Home Products, Inc.

All rights reserved.

Installation Instructions

Installation Instructions

(continued)

Installation in a double-hung sash window

1. Cut the foam seals(adhesive type) to the proper lengths and attach them

to the window and stool. (Fig. 9 )

2. Open the window sash and place the window slider kit on the window stool

(Fig. 1 0 ). Attach the window slider kit to the window stool. Adjust the length

of the window slider kit according to the width of window. Screw down the

two screws on the window slider kit. See Fig.1

0 . Cut the adjustable window

slider kit if the width of window is less than 67.5cm (Fig. 1 1 ).

3. Close the window sash securely against the window slider kit. (Fig. 1 2 )

4. Drive two 12.7 mm screws to secure the window slider kit to the window

sash.

(FIG. 1 2 )

5. Secure the window slider kit to the window stool

(FIG. 1 2 )

:

A: For wooden windows: Use 19mm screws for securing.

B: For Vinyl-Clad windows: Use

12.7mm hex head cap screws

for securing.

6.

To secure lower sash in place, attach right angle sash lock with

12.7mm (1/2 ″ ) screw as shown (FIG. 1 3 ).

NOTE:

It is difficult to lock the windows with the sash lock for Vinyl-Clad windows, so you can use lock by window itself.

7. Cut the foam seal to an appropriate length and seal the open gap

between the top window sash and outer window sash, as shown in Fig.1

4 .

12.7mm screws screws

67.5cm~123cm

Window stool

Foam seal A

(adhesive type)

Cut this side to fit your window

Fig. 9

Window slider kit

Fig. 1 0

Window slider kit

Foam seal

Fig. 1 3

Fig. 1 4

19mm screws or 12.7mm hex head cap screws

Window stool

Fig. 1 2

Installation in a sliding sash window

1. Cut the foam seals(adhesive type) to the proper lengths and attach them

to the window frame. See Fig.1

5 .

2. Open the window sash and place the window slider kit on the window stool.

See Fig.1

6 . Attach the window slider kit to the window stool. Adjust the

length of the window slider kit according to the height of window. Screw

down the two screws on the window slider kit. See Fig.1

6 .

　

Cut the adjustable

window slider kit if the height of window is less than 67.5cm (Fig. 1 1 ).

3. Close the sliding sash securely against the window slider kit. (Fig. 1 7 )

4. Drive two 12.7mm screws to secure the window slider kit to the window sash.

(Fig. 1 7 )

5. Drive two 19mm screws to secure the window slider kit to the window stool.

(Fig. 1 7 )

6. Cut the foam seal to an appropriate length and seal the open gap

between the sliding sash and outer window sash, as shown in Fig.1

8 .

7. To secure the sliding sash in place, attach right angle sash lock with 12.7mm

(1/2") screw as shown.(Fig.

19 )

Foam seal

(adhesive type)

Window stool

67.5cm~123cm

Window stool

Window slider kit screws

Window slider kit

Fig. 1 1

Fig. 1 5

Fig. 1 6

Foam seal

Fig. 1 8

2009 Electrolux Home Products, Inc.

Fig. 19

19mm screws

12.7mm screws

All rights reserved.

Fig. 1 7

7

Air Conditioner Features

Air Conditioner Features

CONTROL PANEL

REMOTE CONTROL

MODE INDICATION

TEMPERATURE BUTTON

MODE SELECTOR

SLEEP BUTTON

RESET + LOCK

PIN BUTTONS

Fig. 20

FAN SPEED SELECTION

FAN SPEED SELECTOR

TIMER BUTTONS

SWING BUTTON

ON/OFF BUTTON

Fig. 21

Battery Size: AAA

Warning:

1.

Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-

cadmium) batteries.

2. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

NOTE

8

The RESET button is depressed when you want to return to the initial factory settings. The LOCK button is depressed to lock the keypad so the settings cannot be changed. The key symbol will appear in the display of the remote control, depress the LOCK button again to release. Use a small pin to depress these buttons.

Heating function is for heating and cooling model only.

2009 Electrolux Home Products, Inc.

All rights reserved.

Operating Instructions

Operating Instructions

NOTE

The following instructions represent the Control Panel, the same instructions can be used for the Remote Control.

(except timer function)

COOLING MODE:

HEATING MODE:

(on some models)

DRY MODE:

AUTO MODE:

FAN MODE:

In this mode the adaptor hoses MUST be used.

1. Press the MODE button until the "Cool" indicator lights.

2. Press the " " Temp buttons for desired setting.

3. Press the FAN button for desired fan speed.

In this mode you do not need to use the adaptor hoses.

1. Press the MODE button until the "Heat" indicator lights.

2. Press the " " Temp buttons for the desired heat setting.

Under Heating mode, you can not select the fan speed.

In this mode you do not need to use the adaptor hoses, BUT the water collected must be discharged. See Drainage Section.

1. Press the MODE button until the "Dry" indicator lights.

2. The fan will run at low speed and the display will show the room temperature.

3. Keep doors

　 windows closed for best effect.

Always have the hose s attached in this mode.

When you set the air conditioner in AUTO mode, it will automatically select cooling, heating(not applicable for cooling only models), or fan only operation depending on what temperature you have selected and the room temperature. The air conditioner will control room temperature automatically round the temperature point set by you. Under

AUTO mode, you can not select the fan speed.

In this mode there is no need to use the exhaust hose or drainage hose.

However, if you require stale or smokey air to be removed from the room, hook up the duct accessories as described in the "EXHAUSTING HOT AIR" section.

1. Press the MODE button until the "Fan" indicator lights.

2. Press the FAN button to choose the desired fan speed.

3. The fan will run at the selected speed and the display will show the room temperature.

TIMER OPERATION:

You can set both delay stop and delay start while unit is in ON position or OFF position.

When unit is in ON position, first press TIMER button to go to delay stop setting, then

“timer off” light will illuminate, tap or hold the UP arrow ( ) or the DOWN arrow ( ) to change delay stop timer at 0.5 hour increments up to 10 hours, then at 1 hour increments up to 24 hours. Then press the TIMER button to confirm the setting (the control will confirm the setting automatically after 5 seconds) and go to delay start setting. Use the same way as above to set the delay start timing. If you don’t need to set delay start, press the

TIMER button again to exit. After 5 seconds, the control will automatically change the display back to previous temperature display. If you want to check remain timing, press the

TIMER button. The delay start operation automatically selects mode, temperature and fan speed the same as last operation you set.

When unit is in OFF position, press TIMER button will first go to delay start setting, then

“timer on” light will illuminate, set the delay start and delay stop timing the same way as above.

To cancel the timer setting, simply tap ( ) or ( ) button to change the timing to 0.0.

You can set both delay stop and delay start by using the remote control, while unit is in ON position or OFF position. To set the delay stop timing, first press TIMER OFF button on the remote control to go to delay stop setting, then tap or hold the TIMER OFF button to change delay stop timer at 0.5 hour increments up to 10 hours, then at 1 hour increments up to 24 hours. After the desired setting is reached stop pressing the TIMER OFF button, the control will confirm the setting automatically after 5 seconds and change the display back to previous

2009 Electrolux Home Products, Inc.

All rights reserved.

9

Operating Instructions

Operating Instructions

(continued)

temperature display. Use the same way as above to set the delay start timing by pressing

TIMER ON button. To cancel the timer setting, simply tap TIMER ON or TIMER OFF button to change the timing to 0.0.

SLEEP OPERATION:

In this mode the selected temperature will increase by 1 °C 30 minutes after the mode is selected. The temperature will then increase by another 1 °C after an additional 30 minutes. This new temperature will be maintained for 7 hours before it returns to the originally selected temperature. This ends the "Sleep" mode and the unit will continue to operate as originally programmed. The "Sleep" mode program can be cancelled at any time during operation by again pressing the "Sleep" button.

Note:

This feature is unavailabe under FAN or DRY modes.

SWING OPERATION:

When you turn on the unit, the louver will swing and stop at a certain angle. You can press the SWING button to let the louver swing automatically. Press the

SWING button again while you want the louver stop at desired angle.

CHECK FILTER FEATURE:

This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more efficient operation. The filter indicator will illuminate after 250 hours of operation.

To reset after cleaning the filter, press the "Filter" button and the light will go off.

SELECTING FAN SPEED:

AUTO LOW

HIGH MED

You can select the desired fan speed, by pressing the FAN SPEED button. The fan speed will change in the sequence as the drawing on the left.

NOTE: After choosing the fan speed as “LOW”, “MED” or “HIGH”, the cooresponding fan speed indicator light will illuminate. After the AUTO fan speed is selected, no fan speed indicator light will illuminate. Under AUTO, Heat, Dry mode, you can not select the fan speed.

FAULT CODE:

If the display reads "EA" , the room temperature sensor has failed. Contact your Authorized

Frigidaire Service Center.

10

If the display reads "ES" , the evaporator temperature sensor has failed. Contact your

Authorized Frigidaire Service Center.

If the display reads "E4" , the display panel communication has failed. Contact your

Authorized Frigidaire Service Center.

If the display reads "P1" , bottom tray is full. Carefully move the unit to a drain location, remove the bottom drain plug and let the water drain away. Restart the machine until the "P1" symbol disappears. If error repeats, call for service.

DRAINAGE:

During the dehumidifying mode, you will need a garden hose (sold separately) to drain the condensate from the unit.

Remove the rubber stopper from the hose connector, then screw on a garden hose to the connector as shown on fig 2 2 .

The hose may then:

A. Discharge into a drain that is lower than the unit.

B. Be connected to a condensate pump (sold separately).

C. During cooling mode, please replace the rubber stopper to the hose connector to reach the maximum performance.

Garden hose

Remove the supplied rubber stopper

Fig. 2

2

2009 Electrolux Home Products, Inc.

All rights reserved.

Operating Instructions, CARE & CLEANING

Operating Instructions

(continued)

ADDITIONAL THINGS

YOU SHOULD KNOW

Now that you have mastered the operating procedure, here are more features in your control that you should become familiar with.

The "Cool" circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly. This prevents overheating of the compressor and possible circuit breaker tripping. The fan will continue to run during this time.

Temperature can be set between 17 °C and 30 °C (62 °F and 86 °F).

The control is capable of displaying temperature in degrees Fahrenheit or degrees

Celsius. To convert from one to the other and back, press and hold the "TEMP"

Up ( ) and Down ( ) buttons together for 3 seconds.

There is a 2-Second delay for the compressor shutting down when selecting

FAN ONLY/HEAT. This is to cover the possibility of having to roll through to select another mode.

After a power outage, the unit will memorize the last setting and return the unit to the same setting once power is restored.

Indoor operating temperature range for this product is 62 °F to 95 °F (17 °C to 3 5 °C).

During normal use, the indoor air inlet switch should be close. To circulate the room air, switch the indoor air inlet switch to OPEN position.

CARE & CLEANING

Filter

Fig. 23

Clean your air conditioner occasionally to keep it looking new.

Be sure to unplug the unit before cleaning to prevent shock or fire hazards.

Air Filter Cleaning

This unit has a filter. Grasp the upper panel tab and take off the filter which behind the grill of the back panel (Fig.2

3 ).

Wash the filter using liquid dishwashing detergent and warm water. Rinse filter thoroughly. Gently shake excess water from the filter. Be sure filter is thoroughly dry before replacing.

Or, instead of washing you may vacuum the filter clean.

Cabinet Cleaning

Be sure to unplug the air conditioner to prevent shock or fire hazard. The cabinet and front may be dusted with an oil-free cloth or washed with a cloth dampened in a solution of warm water and mild liquid dishwashing detergent. Rinse thoroughly and wipe dry.

Never use harsh cleaners, wax or polish on the cabinet front.

Be sure to wring excess water from the cloth before wiping around the controls.

Excess water in or around the controls may cause damage to the air conditioner.

Winter Storage

If you plan to store the appliance during the winter, cover it with plastic or return it to its carton.

2009 Electrolux Home Products, Inc.

All rights reserved.

11

Before You Call

Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not the result of defective workmanship or materials in this appliance.

OCCURRENCE SOLUTION

Air conditioner will not operate.

Air from unit does not feel cold enough.

Air conditioner cooling, but room is too warm - ice forming on cooling coil behind decorative front

Air conditioner cooling, but room is too warm - NO ice forming on cooling coil behind decorative front.

Air conditioner turns on and off rapidly.

Noise when unit is cooling.

Room too cold.

Room too hot.

Wall plug disconnected. Push plug firmly into wall outlet.

Plug Current Device Tripped. Press the RESET button.

House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.

Control is OFF. Turn Control ON and set to desired setting.

P1 appears in the display window. Drain water as described in Drainage Section.

Shut off in Heat mode. When the air outlet overheats, the automatic heat protection engages. Remove any blockages and let appliance cool down. If the heating function can not be restarted after fully cooling down, the thermal fuse may open the heater circuit, then call for service.

Room Temperature lower than the set temperature (Cool Mode). Reset the temperature.

Room Temperature higher than the set temperature (Heat Mode). Reset the temperature.

Room temperature below 16 °C (60 °F). Cooling may not occur until room temperature rises above

16 °C (60 °F).

Reset to a lower temperature.

Compressor shut-off by changing modes. Wait approximately 3 minutes and listen for compressor to restart when set in the COOL mode.

Outdoor temperature below 16 °C (60 °F). To defrost the coil, set FAN ONLY mode.

Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set to FAN ONLY mode.

Temperature is set too low for night-time cooling. To defrost the coil, set to FAN ONLY mode. Then, set temperature to a higher setting.

Ducts not connected or blocked. See HOSES INSTALLATION Section.

Dirty air filter - air restricted. Clean air filter. Refer to Care and Cleaning section.

Temperature is set too high. Set temperature to a lower setting.

Air directional louvers positioned improperly. Position louvers for better air distribution.

Front of unit is blocked by drapes, blinds, furniture, etc. - restricts air distribution. Clear blockage in front of unit.

Doors, windows, registers, etc. open - cool air escapes. Close doors, windows, registers, etc.

Unit recently turned on in hot room. Allow additional time to remove “stored heat” from walls, ceiling, floor and furniture.

Dirty air filter - air restricted. Clean air filter.

Outside temperature extremely hot. Set FAN speed to a faster setting to bring air through cooling coils more frequently.

Air movement sound. This is normal. If too loud, set to lower FAN setting.

Vibration from uneven floor. Move or support appliance correctly on even surface.

Set temperature too low. lncrease set temperature.

Set temperature too high. Lower setting.

If These Solutions Fail, Call 1-800-944-9044(US)/1-800-265-8352(Canada)

For Frigidaire Service.

12 2009 Electrolux Home Products, Inc.

All rights reserved.

Major Appliance Limited Warranty

Your appliance is covered by a limited one-year warranty and a limited 2-5 year warranty on the sealed system (the compressor, condenser, evaporator and tubing). For one year from your original date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions. From the second to the fifth year from your original purchase date, Electrolux will repair or replace any parts in the Sealed Refrigeration System (compressor, condenser, evaporator and tubing) that prove to be defective in materials or workmanship. In years 2-5, the consumer will be responsible for diagnostic, labor and parts costs as well as any removal, transportation and reinstallation expenses which are incurred during service on components other than those covered under the Sealed Refrigeration System 5-year warranty.

Exclusions This warranty does not cover the following:

1. Products with original serial numbers that have been removed, altered or cannot be readily determined.

2. Product that has been transferred from its original owner to another party or removed outside the USA or

Canada.

3. Rust on the interior or exterior of the unit.

4. Products purchased "as-is" are not covered by this warranty.

5. Food loss due to any refrigerator or freezer failures.

6. Products used in a commercial setting.

7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not in ordinary household use or used other than in accordance with the provided instructions.

8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.

9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc., which are not a part of the appliance when it is shipped from the factory.

10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs, handles, or other cosmetic parts.

11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip charges, or mileage expense for service calls to remote areas, including the state of Alaska.

12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors, cabinets, walls, etc.

13. Damages caused by: services performed by unauthorized service companies; use of parts other than genuine Electrolux parts or parts obtained from persons other than authorized service companies; or external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR

REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST

PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR

CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES

RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME

STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE-

QUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS

OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.

YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.

If You Need

Service

Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.

Service under this warranty must be obtained by contacting Electrolux at the addresses or phone numbers below.

This limited warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances

North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp.

Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under this warranty must be performed by Electrolux or an authorized service company. Product features or specifications as described or illustrated are subject to change without notice.

USA

1.800.944.9044

Electrolux Major Appliances

10200 David Taylor Drive

Charlotte, NC 28262

Canada

1.800.265.8352

Electrolux Canada Corp.

5855 Terry Fox Way

Mississauga, Ontario, Canada

L5V 3E4

2009 Electrolux Home Products, Inc.

All rights reserved.

13