DESCRIPTION Specifications
e Brass construction
e Flexible supply lines with 3/8” & 1/2" or 9/16" & 1/2"
compression fittings
e Includes Red/Blue indicators
FLOW a A Г
* Water usage is limited to these maximum flow rates
as indicated by the corresponding product markings |
* North America: 1.5 gpm max (5.7L/min) at 60psi a
e California: 1.2 gpm max (4.5L/min) at 60psi
See
CARTRIDGE pe es
e Brass cartridge
STANDARDS 8" Dual-Handle Lavatory Faucet
e Certified to CUPC NOTE: SPOUT INSTALLS THRU Ф1-3/8”
e Certified to AB1953 MIN HOLE
e Certified to NSF/ANSI 61
e Certified to Water sense
» ADA O for lever handle
WARRANTY
e Lifetime limited warranty against leaks, drips and
finish defects to the original consumer purchaser
* 5 year warranty if used in commercial installations
5-31/32"
151,5mm
==
-9/16”
1-21/32" = it 5
42mm TE ue
x 0 :
= E MM
< E BN > £
un cu 9 #1-31/32" Ze
ot iH 350mm au À
#1-31/32” = +
é50mm
@1-31/32' |
rc _—— — = ых
ZA
ZZ ZA
| й | Ш |
4 de
1016mm 1016mm
CRITICAL DIMENSIONS
8" Dual-Handle Lavatory Faucet Installation
INSTALLATION MANUAL Tools You Will Need :
iE
Hexagon wrench
Adjustable wrench
2
Philips Screwdriver
Notes before installation :
1.Please check that all components are
present.
2.Before installation ensure that all
feed lines are clear of debris and
on/off valve is present.
3.Ensure water pressure is between
20-125 PSI (includes combination of
hot and cold feed lines).
4.Pictures in the manual are general in
content and may not represent
exactly your purchased faucet. If
you are having difficulties please
contact a professional plumber.
5.1f you will be away from home for an
extended period you should shut off
the main water supply.
Daily maintenance
1.Use a soft cloth and vinegar to
‘remove hard-water spots.
2.Check aerator (if present) regularly
for calcium build up are when water
stream is not optimum.
3.DO NOT use caustic cleaning
products as the use will break down
finish and will void the product
warranty.
4.Acceptable cleaners include vinegar
or mild non-abrasive liquid
detergents.
5.If the water pressure appears to be
less than optimum remove, inspect,
clean or replace aerator.
E 7 : 7 7 - 7 7 E 7 per у E 7 у A Г EE EEE, EE 7 7 7 я И,
À TE
a
1.Remove the T-valve,lock nut and
washer from the spout body.Place
spout in center hole of sink.Assembly
washer and tighten the lock nut to it.
Connect the T-valve to the spout body
using the wrench .
2.Remove mounting hardware from
handle body.Connect water supply tube
to valve body and tighten with lock nut.
Do not allow the water supply brass tube
to twist.Use two wrenches,as shown in
the diagram, tighten the flexible hose.
ue = ce
Ee) ¥
3.Place the spout in center hole of sink
and handle body through right hole.
(Left is red, right is blue).Assemble the
rubber washer,washer and tighten with
lock nut.
4.Connect handle body and faucet body
with braided hoses. Tighten wrench tight.
5.Screw and tighten the flexible hose to
the faucet.Left is red, right is blue.Do not
allow the water supply brass tube to
twist.
HOT
6.Attach flexible hose to water supply.
">
