Bacillus

Cyanobacteria

Polio

Cryptosporidium

E. Coli

Shigella

* These microorganisms may/may not exist in your household water.

It is important that you have your water tested to identify microorganisms and/or contaminants, if any.

Bacillus

Cyanobacteria

Polio

Cryptosporidium

Polaris Scientific UV™ Sterilization Systems utilize a natural quartz sleeve to protect the lamp and allow the maximum amount of UV rays to penetrate and disinfect the water.

Polaris Scientific UV™ Sterilization Systems germicidal lamps are specially designed UV radiation lamps which produce a rated wave length of 254nm.

Polaris Scientific UV™ Sterilization Systems are your best choice in UV sterilization. With its durable construction, high quality quartz sleeve and performance lamps, you can’t go wrong .

Your best choice in Ultraviolet Sterilization.

FEATURES E. Coli

3 Audible ballast with LED lamp out indicator.

3 High output low pressure mercury vapor lamps with high isolation pin design.

3 Open end quartz sleeve and stainless steel gland units.

3 Operating temperature and sealing efficiency.

3 Limited 5-year warranty on stainless steel housing.

Shigella

3 Limited 1-year warranty on electronics.

Po aris Scientif ic

* These microorganisms may/may not exist in your household water.

It is important that you have your water tested to identify microorganisms and/or contaminants, if any.

Accessories e Ad antage

SAFE

• No need to handle toxic or corrosive chemicals or by-products

• Microbiologically free water without the use of potentially dangerous chemicals

• UV imparts no change in taste, odor, pH or conductivity

• No trihalomethanes (THM’s) formation

SIMPLE

• Fast and simple installation with three connections

(two water and one electrical).

• Maintenance involves annual lamp replacement

(provided water quality parameters are met) with no need to turn off water flow.

• Automatic, unattended and user friendly operation.

EFFICIENT

• Compact units with 304 or 316 (upon request) stainless steel reactor chamber, polished for laboratory and medical use, require minimum space.

• Microorganisms are inactivated within seconds; eliminates the need for long retention times or retention tanks.

• Very low power consumption; less than 40-watt bulb to effectively treat from 1 to 100 gallons per minute.

• High output low pressure mercury vapor lamps with high isolation pin.

• Little change in water temperature even after prolonged periods of no water flow.

• Open end high quality quartz sleeve and stainless steel gland units.

ECONOMICAL

• No moving parts to wear out or break.

• Lower capital investment when compared to chlorine

Polaris Scientific UV™ Sterilization Systems utilize a natural quartz sleeve to protect the lamp and allow the maximum amount of UV rays to penetrate and disinfect the water.

Polaris Scientific UV™ Sterilization Systems germicidal lamps are specially designed UV radiation lamps which produce a rated wave length of 254nm.

Polaris Scientific UV™ Sterilization Systems are your best choice in UV sterilization. With its durable construction, high quality quartz sleeve and performance lamps, you can’t go wrong .

Residential and Commercial UV Sterilization

Your best choice in Ultraviolet Sterilization.

FEATURES

3 Audible ballast with LED lamp out indicator.

3 High output low pressure mercury vapor lamps with high isolation pin design.

3 Open end quartz sleeve and stainless steel gland units.

3 Operating temperature and sealing efficiency.

3 Limited 5-year warranty on stainless steel housing.

3 Limited 1-year warranty on electronics.

Po aris Scientif ic Accessories e Ad antage

SAFE

• No need to handle toxic or corrosive chemicals or by-products

• Microbiologically free water without the use of potentially dangerous chemicals

• UV imparts no change in taste, odor, pH or conductivity

• No trihalomethanes (THM’s) formation

SIMPLE

• Fast and simple installation with three connections

(two water and one electrical).

• Maintenance involves annual lamp replacement

(provided water quality parameters are met) with no need to turn off water flow.

• Automatic, unattended and user friendly operation.

EFFICIENT

• Compact units with 304 or 316 (upon request) stainless steel reactor chamber, polished for laboratory and medical use, require minimum space.

• Microorganisms are inactivated within seconds; eliminates the need for long retention times or retention tanks.

• Very low power consumption; less than 40-watt bulb to effectively treat from 1 to 100 gallons per minute.

• High output low pressure mercury vapor lamps with high isolation pin.

• Little change in water temperature even after prolonged periods of no water flow.

• Open end high quality quartz sleeve and stainless steel gland units.

ECONOMICAL

• No moving parts to wear out or break.

• Lower capital investment when compared to chlorine or ozone systems.

Residential and Commercial UV Sterilization

Polaris Scientific Ultraviolet Systems

have a sleek, compact design and provide cost effective ultraviolet water sterilization for low to medium flow applications. Polaris Scientific UV’s are perfect for residential and light commercial reverse osmosis systems, water vending machines, food industry, laboratory, final electronic component rinsing and recirculation loops to name a few.

Polaris Scientific Ultraviolet Systems

produce little change in water temperature even after prolonged

periods of no water flow, making them ideal for many application requirements.

Your

best

choice in Ultraviolet Sterilization

Residential Ultraviolet Sterilization Systems

1

P A R T S & A C C E S S O R I E S

Electronic Ballast Quartz Sleeve Lamp

BEB-1024 QS10 GL10PP

Additional Accessories Specific to Your UV System

UV-NUT-1 UV-SEAL UV-WASHER

UVA-1C

Width

2”

2 gpm at recommended

UV dose of

16 mJ/cm 2

UVA

12

C

Cryptosporidium

& Giardia Lamblia eradicated at

E. coli eradicated at 6.6 mJ/cm 22

<10 mJ/cm 22

UVA-8

C

UVA-6C

UVA-4C

UVA2 C

UVA1 C

1966

Public Health

1 gpm at recommended

UV dose of

30 mJ/cm 2

0.5 gpm at recommended

UV dose of

40 mJ/cm 22

Manufacturer’s

Standard

NSF/EPA

Standard

Maximum

Pressure

125 PSI

Working

Temp.

35 o F

-

104 o F

Wavelength Microjoules

254 nm 30 mJ/cm 2

GPM

1

BEB-1024

Rated Life

(hours)

9,000

Lamp Watts

10W

Voltage @

50/60HZ

110V/220V

Visual

Warning

LED

Audible

Warning

BUZZER

Number of

Lamps

1

Port Size

Inlet/Outlet

1/4” MNPT

Water

Chamber

STAINLESS

304

Length

10.47”

QS14 GL14PP

2

P A R T S & A C C E S S O R I E S

Electronic Ballast Quartz Sleeve Lamp

Additional Accessories Specific to Your UV System

UV-NUT-1 UV-SEAL UV-WASHER

UVA-2C

GPM

2

Rated Life

(hours)

Lamp Watts

9,000 14W

Voltage @

50/60HZ

110V/220V

Visual

Warning

LED

Audible

Warning

BUZZER

Number of

Lamps

Port Size

Inlet/Outlet

1 1/4” MNPT

Water

Chamber

STAINLESS

304

Length

13.74”

Width

2.5” recommended

UV dose of

16 mJ/cm 2

UVA

12

C

Cryptosporidium

& Giardia Lamblia eradicated at

E. coli eradicated at 6.6 mJ/cm 22

<10 mJ/cm 22

UVA-8

C

UVA-6C

UVA-4C

UVA2 C

UVA1 C

1966

Public Health

2 gpm at recommended

UV dose of

30 mJ/cm 22

1 gpm at recommended

UV dose of

40 mJ/cm 222

Manufacturer’s

Standard

NSF/EPA

Standard

Maximum

Pressure

125 PSI

Working

Temp.

35 o F 104 o F

Wavelength Microjoules

254 nm 30 mJ/cm 2

A A

Residential Ultraviolet Sterilization Systems

BEB-1024 QS17 GL17PP

4

P A R T S & A C C E S S O R I E S

Electronic Ballast Quartz Sleeve Lamp

Additional Accessories Specific to Your UV System

UV-NUT-1 UV-SEAL UV-WASHER

UVA-4C

GPM

4

Rated Life

(hours)

Lamp Watts

9,000 17W

Voltage @

50/60HZ

110V/220V

Visual

Warning

LED

Audible

Warning

BUZZER

Number of

Lamps

1

Port Size

Inlet/Outlet

1/2” MNPT

Water

Chamber

STAINLESS

304

Length

15.50”

Width

2.5” recommended

UV dose of

16 mJ/cm 2

UVA

12

C

Cryptosporidium

& Giardia Lamblia eradicated at

E. coli eradicated at 6.6 mJ/cm 22

<10 mJ/cm 22

UVA-8

C

UVA-6C

UVA-4C

UVA2 C

UVA1 C

1966

Public Health

4 gpm at recommended

UV dose of

30 mJ/cm 2

3.5 gpm at recommended

UV dose of

40 mJ/cm 22

Manufacturer’s

Standard

NSF/EPA

Standard

Maximum

Pressure

125 PSI

Working

Temp.

35 o F 104 o F

Wavelength

254 nm

Microjoules

30 mJ/cm 2

P A R T S & A C C E S S O R I E S

Electronic Ballast Quartz Sleeve

BEB-2439

UV-NUT-1 /

UV-NUT-2

QS24

UV-SEAL

Lamp

GL24PP

Additional Accessories Specific to Your UV System

6

UV-WASHER UV-PLUG

UVA-6C

GPM

6

Rated Life

(hours)

Lamp Watts

9,000 24W

Voltage @

50/60HZ

110V/220V

Visual

Warning

LED

Audible

Warning

INDICATOR

W/ ALARM

Number of

Lamps

1

Port Size

Inlet/Outlet

1/2” MNPT

Water

Chamber

STAINLESS

304

Length

23.23”

Width

2.5”

11 gpm at recommended

16 mJ/cm 2

UVA

12

C

Cryptosporidium

& Giardia Lamblia eradicated at

E. coli eradicated at 6.6 mJ/cm 22

<10 mJ/cm 22

UVA-8

C

UVA-6C

UVA-4C

UVA2 C

UVA1 C

1966

Public Health

6 gpm at recommended

UV dose of

30 mJ/cm 2

4.5 gpm at recommended

UV dose of

40 mJ/cm 22

Manufacturer’s

Standard

NSF/EPA

Standard

Maximum

Pressure

125 PSI

Working

Temp.

35 o F 104 o F

Wavelength Microjoules

254 nm 30 mJ/cm 2

A A

Residential Ultraviolet Sterilization Systems

Additional Accessories Specific to Your UV System

UV-NUT-1 /

UV-NUT-2

UV-32SPRING UV-SEAL

UV-WASHER UV-PLUG

8

P A R T S & A C C E S S O R I E S

Electronic Ballast Quartz Sleeve Lamp

BEB-2439 QS32 GL32PP

UVA-8C

GPM

8

Rated Life

(hours)

Lamp Watts

9,000 32W

Voltage @

50/60HZ

110V/220V

Visual

Warning

LED

Audible

Warning

INDICATOR

W/ALARM

Number of

Lamps

Port Size

Inlet/Outlet

1 3/4” MNPT

Water

Chamber

STAINLESS

304

Length

27.87”

Width

2.5”

15 gpm at recommended

UV dose of

2

UVA

12

C

Cryptosporidium

& Giardia Lamblia

E. coli eradicated at 6.6 mJ/cm 22 eradicated at

<10 mJ/cm 22

UVA-8

C

UVA-6C

UVA-4C

UVA2 C

UVA1 C

1966

Public Health

8 gpm at recommended

UV dose of

30 mJ/cm 2

6.5 gpm at recommended

UV dose of

40 mJ/cm 22

Manufacturer’s

Standard

NSF/EPA

Standard

Maximum

Pressure

125 PSI

Working

Temp.

35 o F 104 o F

Wavelength Microjoules

254 nm 30 mJ/cm 2

12

P A R T S & A C C E S S O R I E S

Electronic Ballast Quartz Sleeve

BEB-2439 QS39

Lamp

GL39PP

Additional Accessories Specific to Your UV System

UV-NUT-1 /

UV-NUT-2

UV-39SPRING UV-SEAL

UV-WASHER UV-PLUG

UVA-12C

GPM

12

Rated Life

(hours)

Lamp Watts

9,000 39W

Voltage @

50/60HZ

110V/220V

Visual

Warning

LED

Audible

Warning

INDICATOR

W/ ALARM

Number of

Lamps

1

Port Size

Inlet/Outlet

3/4” MNPT

Water

Chamber

STAINLESS

304

Length

36.81”

23 gpm at recommended

UV dose of

22

UVA

12

C

Cryptosporidium

& Giardia Lamblia

E. coli eradicated at 6.6 mJ/cm 22 eradicated at

<10 mJ/cm 22

UVA-8

C

UVA-6C

UVA-4C

UVA2 C

UVA1 C

1966

Public Health

12 gpm at recommended

UV dose of

30 mJ/cm 2

9 gpm at recommended

UV dose of

40 mJ/cm 22

Manufacturer’s

Standard

NSF/EPA

Standard

Width

2.5”

Maximum

Pressure

125 PSI

Working

Temp.

35 o F 104 o F

Wavelength Microjoules

254 nm 30 mJ/cm 2

A A

Commercial Ultraviolet Sterilization Systems

24B

P A R T S & A C C E S S O R I E S

Electronic Ballast Quartz Sleeve Lamp

ZEB-2439 QS39 GL39PP

Additional Accessories Specific to Your UV System

UV-NUT-1 /

UV-NUT-2

UV-39SPRING UV-SEAL

UV-WASHER UV-PLUG UV-TIMER

GPM

24

UVA-24B

110

100

90

80

70

200

190

180

170

160

150

140

130

120

60

50

40

30

20

10

Cryptosporidium

& Giardia Lamblia eradicated at

<10 mJ/cm 22

E. coli eradicated at 6.6 mJ/cm 2

UV

A-

1

00

B

UV

A-8

0

B

UVA

UVA

-60

-50

B

B

UVA

3

6 B

UVA-

2 4 B

UV

A-

1

50

B

0 10 20

Manufacturer’s

Standard

30

UV

A-

2

00

B

UV dose of

30 mJ/cm

40 50

NSF/EPA

Standard

2

UV dose of

40 mJ/cm 2

60

Rated Life

(hours)

Lamp Watts

9,000 39W

Voltage @

50/60HZ

110V/220V

Visual

Warning

LED

Audible

Warning

INDICATOR

W/ALARM

Number of

Lamps

2

Port Size

Inlet/Outlet

1” MNPT

Water

Chamber

STAINLESS

304

Timer Length Width

Maximum

Pressure

Working

Temp.

Wavelength Microjoules



36.93” 3.5” 125 PSI 35 o F 104 o F 254 nm 30 mJ/cm 2

36B

P A R T S & A C C E S S O R I E S

Electronic Ballast Quartz Sleeve Lamp

ZEB-2439 QS39 GL39PP

Additional Accessories Specific to Your UV System

UV-NUT-1 /

UV-NUT-2

UV-39SPRING UV-SEAL

UV-WASHER UV-PLUG UV-TIMER

UVA-36B

70

60

50

40

30

20

10

200

190

180

170

160

150

140

130

120

110

100

90

80

Cryptosporidium

& Giardia Lamblia eradicated at

<10 mJ/cm 22

E. coli eradicated at 6.6 mJ/cm 2

UV

A-

1

00

B

UV

A-8

0

B

UVA

-60

B

UVA

-50

B

UVA

3

6

B

UVA-

2 4 B

UV

A-

1

50

B

0 10 20

Manufacturer’s

Standard

30

UV

A-

2

00

B

UV dose of

30 mJ/cm

40 50

NSF/EPA

Standard

2

UV dose of

40 mJ/cm 2

60

GPM

Rated Life

(hours)

Lamp Watts

36 9,000 39W

NOTE: Flanges available upon request.

Voltage @

50/60HZ

110V/220V

Visual

Warning

LED

Audible

Warning

INDICATOR

W/ ALARM

Number of

Lamps

3

Port Size

Inlet/Outlet

1.5”

Water

Chamber

STAINLESS

304

Timer Length Width

Maximum

Pressure

Working

Temp.

Wavelength Microjoules



36.93” 5.5” 125 PSI 35 o F 104 o F 254 nm 30 mJ/cm 2

A A

Commercial Ultraviolet Sterilization Systems

50B

P A R T S & A C C E S S O R I E S

Electronic Ballast Quartz Sleeve Lamp

ZEB-2439 QS39 GL39PP

Additional Accessories Specific to Your UV System

UV-NUT-1 /

UV-NUT-2

UV-39SPRING UV-SEAL

UV-WASHER UV-PLUG UV-TIMER

UVA-5 0 B

110

100

90

80

70

200

190

180

170

160

150

140

130

120

60

50

40

30

20

10

Cryptosporidium

& Giardia Lamblia eradicated at

<10 mJ/cm 22

E. coli eradicated at 6.6 mJ/cm 2

UV

A-

1

00

B

UV

A-8

0

B

UVA

-60

UVA

-50

B

UVA

3 6

B

B

UVA-

2 4 B

UV

A-

1

50

B

0 10 20

Manufacturer’s

Standard

30

UV

A-

2

00

B

UV dose of

30 mJ/cm 2

40 50

NSF/EPA

Standard

UV dose of

40 mJ/cm 2

60

GPM

50

Rated Life

(hours)

Lamp Watts

9,000 39W

Voltage @

50/60HZ

110V/220V

NOTE: Flanges available upon request.

Visual

Warning

LED

Audible

Warning

INDICATOR

W/ALARM

Number of

Lamps

4

Port Size

Inlet/Outlet

1.5”

Water

Chamber

STAINLESS

304

Timer Length Width

Maximum

Pressure

Working

Temp.

Wavelength Microjoules

 36.93” 5.5” 125 PSI 35 o F

-

104 o F 254 nm 30 mJ/cm 2

60B

P A R T S & A C C E S S O R I E S

Electronic Ballast Quartz Sleeve Lamp

ZEB-2439 QS39 GL39PP

Additional Accessories Specific to Your UV System

UV-NUT-1 /

UV-NUT-2

UV-39SPRING UV-SEAL

UV-WASHER UV-PLUG UV-TIMER

UVA-60 B

110

100

90

80

70

200

190

180

170

160

150

140

130

120

60

50

40

30

20

10

Cryptosporidium

& Giardia Lamblia eradicated at

<10 mJ/cm 22

E. coli eradicated at 6.6 mJ/cm 2

UV

A-

1

00

B

UV

A-8

0

B

UVA

-60

UVA

-50

B

UVA

3 6

B

B

UVA-

2 4 B

UV

A-

1

50

B

0 10 20

Manufacturer’s

Standard

30

UV

A-

2

00

B

UV dose of

30 mJ/cm 2

40 50

NSF/EPA

Standard

UV dose of

40 mJ/cm 2

60

GPM

60

Rated Life

(hours)

Lamp Watts

9,000 39W

Voltage @

50/60HZ

110V/220V

Visual

Warning

LED

Audible

Warning

INDICATOR

W/ ALARM

Number of

Lamps

5

Port Size

Inlet/Outlet

2” or 2.5”

FLANGE

Water

Chamber

STAINLESS

304

Timer Length Width

Maximum

Pressure

Working

Temp.

Wavelength Microjoules



36.93” 5.5” 125 PSI 35 o F 104 o F 254 nm 30 mJ/cm 2

A A

Commercial Ultraviolet Sterilization Systems

80B

P A R T S & A C C E S S O R I E S

Electronic Ballast Quartz Sleeve Lamp

ZEB-2439 QS39 GL39PP

Additional Accessories Specific to Your UV System

UV-NUT-1 /

UV-NUT-2

UV-39SPRING UV-SEAL

UV-WASHER UV-PLUG UV-TIMER

GPM

80

UVA-80 B

90

80

70

60

50

40

30

20

10

200

190

180

170

160

150

140

130

120

110

100

Cryptosporidium

& Giardia Lamblia eradicated at

<10 mJ/cm 22

E. coli eradicated at 6.6 mJ/cm 2

UV

A-

1

00

B

UV

A-8

0

B

UVA

-60

UVA

-50

B

UVA

3

6

B

B

UVA-

2 4 B

UV

A-

1

50

B

0 10 20

Manufacturer’s

Standard

30

UV

A-

2

00

B

UV dose of

30 mJ/cm 2

40 50

NSF/EPA

Standard

UV dose of

40 mJ/cm 2

60

Rated Life

(hours)

Lamp Watts

9,000 39W

Voltage @

50/60HZ

110V/220V

Visual

Warning

LED

Audible

Warning

INDICATOR

W/ALARM

Number of

Lamps

6

Port Size

Inlet/Outlet

2” or 2.5”

FLANGE

Water

Chamber

STAINLESS

304

Timer Length Width

Maximum

Pressure

Working

Temp.

Wavelength Microjoules



36.93” 6.26” 125 PSI 35 o F

-

104 o F 254 nm 30 mJ/cm 2

100B

P A R T S & A C C E S S O R I E S

Electronic Ballast Quartz Sleeve Lamp

ZEB-2439 QS39 GL39PP

Additional Accessories Specific to Your UV System

UV-NUT-1 /

UV-NUT-2

UV-39SPRING UV-SEAL

UV-WASHER UV-PLUG UV-TIMER

UVA-10 0 B

140

130

120

110

100

90

80

200

190

180

170

160

150

70

60

50

40

30

20

10

Cryptosporidium

& Giardia Lamblia eradicated at

<10 mJ/cm

E. coli eradicated at 6.6 mJ/cm 2

22

UV

A-

1

00

B

UV

A-8

0

B

UVA

-60

B UVA

-50

B

UVA

3

6 B

UVA-

2 4 B

UV

A-

1

50

B

0 10 20

Manufacturer’s

Standard

30

UV

A-

2

00

B

UV dose of

30 mJ/cm

40 50

NSF/EPA

Standard

2

UV dose of

40 mJ/cm 2

60

GPM

100

Rated Life

(hours)

9,000

Lamp Watts

39W

Voltage @

50/60HZ

110V/220V

Visual

Warning

LED

Audible

Warning

INDICATOR

W/ALARM

Number of

Lamps

8

Port Size

Inlet/Outlet

2” or 2.5”

FLANGE

Water

Chamber

STAINLESS

304

Timer Length Width

Maximum

Pressure

Working

Temp.

Wavelength Microjoules



36.93” 8.62” 125 PSI 35 o F 104 o F 254 nm 30 mJ/cm 2

A A

Commercial Ultraviolet Sterilization Systems

150B

P A R T S & A C C E S S O R I E S

Electronic Ballast Quartz Sleeve Lamp

ZEB-55155 QS39 GL87PP

Additional Accessories Specific to Your UV System

UV-NUT-1 /

UV-NUT-2

UV-39SPRING UV-SEAL

UV-WASHER UV-PLUG UV-TIMER

UVA-15 0 B

90

80

70

60

50

40

30

20

10

200

190

180

170

160

150

140

130

120

110

100

Cryptosporidium

& Giardia Lamblia eradicated at

<10 mJ/cm 22

E. coli eradicated at 6.6 mJ/cm 2

UV

A-

1

00

B

UV

A-8

0

B

UVA

-60

B

UVA

-50

B

UVA

3

6

B

UVA-

2 4 B

UV

A-

1

50

B

0 10 20

Manufacturer’s

Standard

30

UV

A-

2

00

B

UV dose of

30 mJ/cm 2

40 50

NSF/EPA

Standard

UV dose of

40 mJ/cm 2

60

GPM

150

Rated Life

(hours)

Lamp Watts

9,000 87W

Voltage @

50/60HZ

110V/220V

Visual

Warning

LED

Audible

Warning

INDICATOR

W/ALARM

Number of

Lamps

6

Port Size

Inlet/Outlet

3”

FLANGE

Water

Chamber

STAINLESS

304

Timer Length Width

Maximum

Pressure

Working

Temp.

Wavelength Microjoules



36.93” 8.62” 125 PSI 35 o F 104 o F 254 nm 30 mJ/cm 2

200B

P A R T S & A C C E S S O R I E S

Electronic Ballast Quartz Sleeve Lamp

ZEB-55155 QS39 GL87PP

Additional Accessories Specific to Your UV System

UV-NUT-1 /

UV-NUT-2

UV-39SPRING UV-SEAL

UV-WASHER UV-PLUG UV-TIMER

UVA-20 0 B

200

190

180

170

160

150

140

130

120

110

100

90

80

70

60

50

40

30

20

10

Cryptosporidium

& Giardia Lamblia eradicated at

<10 mJ/cm 22

E. coli eradicated at 6.6 mJ/cm 2

UV

A-

1

00

B

UV

A-8

0

B

UVA

-60

UVA

-50

B

UVA

3

B

UVA-

2

6

B

4 B

UV

A-

1

50

B

0 10 20

Manufacturer’s

Standard

30

UV

A-

2

00

B

UV dose of

30 mJ/cm 2

UV dose of

40 mJ/cm 2

40 50

NSF/EPA

Standard

60

GPM

200

Rated Life

(hours)

Lamp Watts

9,000 87W

Voltage @

50/60HZ

110V/220V

Visual

Warning

LED

Audible

Warning

INDICATOR

W/ALARM

Number of

Lamps

8

Port Size

Inlet/Outlet

4”

FLANGE

Water

Chamber

STAINLESS

304

Timer Length Width

Maximum

Pressure

Working

Temp.

Wavelength Microjoules



36.93” 8.62” 125 PSI 35 o F 104 o F 254 nm 30 mJ/cm 2

A A

FOLD HERE

Gate Fold Cover.indd 2

FOLD

HERE

FOLD

HERE

Cut Guide

Folding Guide

Bacillus

UV-NUT-1

Aluminum Long Nut for Wire Connection for Models UVA-1C – UVA-200B

UV-NUT-2

Aluminum Short Nut with End Plug for Models UVA-6C – UVA-200B

UV-PLUG

Plastic Plug for Nuts for Models

UVA-6C – UVA-200B

UV-SEAL

Seal for Sleeve and Nut for Models

UVA-1C – UVA-200B

UV-WASHER

Washer for Sleeve and Nut for Models

UVA-1C – UVA-200B

UV-TIMER

Counter/Timer for Models UVA-24B – UVA-200B

Cyanobacteria

Polio

Cryptosporidium

E. Coli

Shigella

* These microorganisms may/may not exist in your household water.

It is important that you have your water tested to identify microorganisms and/or contaminants, if any.

UV-32SPRING

Stainless Steel Spring for Model

UVA-8C

UV-39SPRING

Stainless Steel Spring for Models

UVA-12C – UVA-200B

BEB-1024

Ballast for

10W-17W 110V/220V for Models UVA-1C – UVA-4C

BEB-2439

Ballast for

24W-39W 110V/220V for Models UVA-6C – UVA-12C

Z EB-2439

Ballast no cup expose wires for 24W-39W 110V/220V for Models UVA-24B – UVA-100B

ZEB-55155

Ballast for

87W 110V/220V for Models UVA-150B – UVA-200B

QS10

Quartz Sleeve 245mm for 10W UV Lamp for Model UVA-1C

QS14

Quartz Sleeve 331mm for 14W UV Lamp for Model UVA-2C

QS17

Quartz Sleeve 338mm for 17W UV Lamp for Model UVA-4C

QS24

Quartz Sleeve 535mm for 24W UV Lamp for Model UVA-6C

QS32

Quartz Sleeve 665mm for 32W UV Lamp for Model UVA-8C

QS39

Quartz Sleeve 890mm for 39W UV Lamp for Models UVA-12C – UVA-200B

GL10PP

10W 212mm Germicidal Lamp

Single End Patented 4 Pin 254nm for Models UVA-1C

GL14PP

14W 287mm Germicidal Lamp

Single End Patented 4 Pin 254nm for Model UVA-2C

U.S. Patent Number:

D751506

Polaris Scientific UV and the Polaris Scientific UV logo design are registered Trademarks in the United States and certain other countries.

The Polaris Scientific UV Germicidal Lamp Pin Design is patented under United States Patent Number: D751506, and is protected by U.S. Patent and Trademark laws.

GL24PP

24W 436mm Germicidal Lamp

Single End Patented 4 Pin 254nm for Model UVA-6C

GL39PP

39W 843mm Germicidal Lamp

Single End Patented 4 Pin 254nm for Models UVA-12C - UVA-100B

GL32PP

32W 645mm Germicidal Lamp

Single End Patented 4 Pin 254nm for Model UVA-8C

GL87PP

87W 843mm Germicidal Lamp

Single End Patented 4 Pin 254nm for Models UVA-150B - UVA-200B

Polaris Scientific UV™ Sterilization Systems utilize a natural quartz sleeve to protect the lamp and allow the maximum amount of UV rays to penetrate and disinfect the water.

Polaris Scientific UV™ Sterilization Systems germicidal lamps are specially designed UV radiation lamps which produce a rated wave length of 254nm.

Polaris Scientific UV™ Sterilization Systems are your best choice in UV sterilization. With its durable construction, high quality quartz sleeve and performance lamps, you can’t go wrong .

FEATURES

3 Audible ballast with LED lamp out indicator.

3 High output low pressure mercury vapor lamps with high isolation pin design.

3 Open end quartz sleeve and stainless steel gland units.

3 Operating temperature and sealing efficiency.

3 Limited 5-year warranty on stainless steel housing.

3 Limited 1-year warranty on electronics.

Your best choice in Ultraviolet Sterilization.

Po aris Scientif ic Accessories e Ad antage

SAFE

• No need to handle toxic or corrosive chemicals or by-products

• Microbiologically free water without the use of potentially dangerous chemicals

• UV imparts no change in taste, odor, pH or conductivity

• No trihalomethanes (THM’s) formation

SIMPLE

• Fast and simple installation with three connections

(two water and one electrical).

• Maintenance involves annual lamp replacement

(provided water quality parameters are met) with no need to turn off water flow.

• Automatic, unattended and user friendly operation.

EFFICIENT

• Compact units with 304 or 316 (upon request) stainless steel reactor chamber, polished for laboratory and medical use, require minimum space.

• Microorganisms are inactivated within seconds; eliminates the need for long retention times or retention tanks.

• Very low power consumption; less than 40-watt bulb to effectively treat from 1 to 100 gallons per minute.

• High output low pressure mercury vapor lamps with high isolation pin.

• Little change in water temperature even after prolonged periods of no water flow.

• Open end high quality quartz sleeve and stainless steel gland units.

ECONOMICAL

• No moving parts to wear out or break.

• Lower capital investment when compared to chlorine or ozone systems.

Residential and Commercial UV Sterilization

5/25/16 12:49 PM

Product Warranty

R oH

C O M PL I I

S

AN T

FOR POLARIS ULTRAVIOLET UV CHAMBER

POLARIS Ultr av iolet w ar r ants th e UV ch amber on th e POLARIS

Ultr av iolet pr odu ct to be fr ee fr om defects in mater ial and

POLARIS Ultr av iolet w ar r ants or iginal lamps, sleev es and UV sensor s to be fr ee fr om defects in mater ial and w or k mansh ip for a per iod w h eth er based on contr act, tor t (inclu ding negligence), str ict

Ultr av iolet does not w ar r ant th at th e goods ar e of mer ch antable

Ultr av iolet’ s database of ser ial nu mber sales date. We w ill adv ise r epair s or , if it is deter mined th at a r eplacement is r eq u ir ed, w e w ill pr ov ide a r eplacement par t. We w ill th en r etu r n th e par t to th e r espect to th e pr odu cts.

FOR STRUCTURAL, HARDWARE AND ELECTRICAL COMPONENTS

POLARIS Ultr av iolet w ar r ants th e str u ctu r al, h ar dw ar e, and electr ical components to be fr ee fr om defects in mater ial and w or k mansh ip for w ill eith er r epair or r eplace th e sensor and r etu r n th e sensor to inclu de sh ipping and h andling ch ar ges w h ich w ill be collected fr om

GENERAL CONDITIONS AND LIMITATIONS

POLARIS Ultr av iolet dealer , w h o w ill r etu r n it to POLARIS Ultr av iolet. th at a r eplacement is r eq u ir ed, w e w ill pr ov ide a r eplacement par t. inclu de sh ipping and h andling ch ar ges w h ich w ill be collected fr om u se or maintenance, accidents, acts of God or minor scr atch es or installed as ou tlined in th e applicable Ow ner ’ s Manu al. POLARIS

Ultr av iolet ar ising ou t of th e sale of pr odu cts to th e pu r ch aser w h eth er for br each of contr act, negligence, or oth er w ise. Th ese pu r ch aser .

or complete erms onditions see re erse side

Warrant y erms & ondi tions

General Conditions and Limitations

The products described in this document are hereby offered for sale to be established by Hydrofit Quick Connect Fittings, Polaris Scientific

Ultraviolet, Hydron Membranes, Aquatrol, Shok Blok, HydroGuard, Hydronix Water Technology, any of its subsidiaries and its authorized distributors. This offer and its acceptance by any customer (the "Buyer") shall be governed by all of the following Terms and Conditions. Buyer’s order for any item described in this document, when communicated to Hydrofit Quick Connect Fittings, Polaris Scientific Ultraviolet, Hydron

Membranes, Aquatrol, Shok Blok, HydroGuard, Hydronix Water Technology, its subsidiaries or an authorized distributor (the "Seller") verbally or in writing, shall constitute acceptance of this offer. Provided, however, that these terms and conditions shall not operate as a rejection of the

Buyer’s offer unless such offer contains variances in the description, quantity, price, or delivery schedule of the items.

1. Terms and Conditions of Sale.

All descriptions, quotations, proposals, offers, acknowledgments, acceptances and sales of the Seller’s products are subject to and shall be governed exclusively by the terms and conditions stated herein (the "Agreement"). The Buyer’s acceptance of any offer to sell is limited to the terms and conditions in the Agreement. Any terms or conditions in addition to or inconsistent with those stated in the Agreement, proposed by the Buyer in any acceptance of an offer by the Seller, are hereby rejected. No such additional, different or inconsistent terms and conditions shall become part of the agreement between the Buyer and the Seller unless expressly accepted in writing by the Seller. The Seller’s acceptance of any offer to purchase by the Buyer is expressly conditioned upon the Buyer’s assent to all the terms and conditions in this Agreement, irrespective of any terms in addition to, or inconsistent with those contained in the Buyer’s offer. Acceptance of the Seller’s products shall in all events constitute such assent.

2. Documents.

Unless provided otherwise in the Agreement, all catalog descriptions, illustrations, drawings and literature or independently submitted estimates of performance, weights and measurements or other specifications provided by the Seller are mere approximations and the

Seller reserves the right to alter or amend them at any time. The Seller reserves the right to correct clerical or technical errors in the contract documents. The Buyer shall furnish with his order all necessary specifications and information. The Seller takes no responsibility for goods manufactured, priced or delivered not in accordance with the order or the specifications unless the Buyer’s order and specifications are clear and correct.

3. Prices.

Unless otherwise provided, all prices contained in our quotations and written acceptances are ex-works and do not include the cost of packing.

All orders are accepted on the condition that all such prices are subject to revision by the Seller at any time before the goods are dispatched to take account of any price change. In the event that the Buyer does not place the entire order quoted by the Seller for the Buyer, the Seller reserves the right to revise its prices. The Seller also reserves the right to revise its prices if the Buyer modifies the specification or quantity of the goods or the delivery requirements after the order has been accepted by the Seller.

4. Advice.

All advice given in connection with the Seller’s goods is provided without charge to the Buyer. ANY ADVICE AND ASSISTANCE GIVEN BY THE

SELLER TO THE BUYER IS GIVEN AT THE BUYER’S RISK, AND THE SELLER SHALL NOT BE LIABLE FOR ANY LOSS, DAMAGE OR CLAIM ARISING

THEREFROM.

5. Payment.

(a) Unless otherwise provided in the Agreement, or explicitly agreed upon in writing by the Seller, payment is due in full 30 days from date of shipment of the items purchased herein under. (b) In the case of an installment contract, deliveries or parts, payment for each installment delivery or part shall be made under sub-clause (a) as if the same constituted a separate agreement. (c) Amounts not timely paid shall bear interest at the rate of 2-1/2% above the Seller’s bank’s prime rate from time to time in force. (d) In the event that the Buyer fails within one calendar month of the date for payment to effect any payment which may be due under the Agreement or any agreement with the Seller, or if the Buyer commits any breach of the Agreement, or if the Buyer becomes insolvent or commits any act of bankruptcy or contemplation of liquidation, the Seller will be entitled, without prejudice to the Seller’s other rights, to terminate the Agreement or any unfulfilled part thereof, or at the Seller’s option to make partial deliveries.

6. Modifications and Cancellations.

This Agreement is not subject to oral modification or cancellation. A Buyer’s request for modification or cancellation will not be incorporated into the Agreement unless the request is accepted by the Seller in a writing that amends the Agreement. Acceptance of any such requested modification or cancellation shall be at the Seller’s discretion and shall be upon such terms and conditions as the Seller may require.

7. Handling Charge.

Goods supplied in accordance with the Buyer’s order may later be returned to the Seller at the Seller’s discretion provided the return is preauthorized in writing, and the merchandise is unused, in original packages, unaltered, clean and no older than 60 days from the date of shipment by the Seller. The Buyer will be required to pay to the Seller a handling charge of 25% of the purchase price of the returned goods. A copy of the original invoice for the merchandise must accompany all returns.

8. Delivery.

(a) Any delivery dates quoted are approximate only and the Seller shall have no liability for any delays in delivery. (b) Unless provided otherwise, delivery of the goods shall be made when the Seller has notified the Buyer that the goods are ready for dispatch. Regardless of the method of delivery, delivery shall be made F.O.B. Seller’s plant, where the risk of loss shall thereupon pass to the Buyer upon the Seller’s delivery to a carrier. Notwithstanding that the Seller’s prices are ex-works, the Seller is prepared by special contract to procure carriage or freight and insurance on behalf of the Buyer and at Buyer’s cost in which event the Seller shall be under no liability for damage in transit or loss or damage to the goods beyond the point at which the Seller contracts to deliver the same. (c) The Seller will not make drop shipments.

9. Inspection and Rejection.

(a) The following provisions shall apply in relation to all deliveries of goods: the Seller shall not be held liable for any claims of damage in transit, shortage of delivery or loss of goods, unless in the case of shortage of delivery, a separate notice in writing is given to the carrier concerned and to the Seller within three (3) days of the receipt of the goods, followed by a complete claim in writing within five (5) days of receipt of the goods and in the case of loss of goods, a separate notice in writing is given to the carrier concerned and to the Seller and a complete claim in writing made within thirty (30) days of the date of consignment. The Buyer must inspect the goods on arrival from the carrier; however, where goods are accepted from the carrier concerned without being inspected, the delivery book of the carrier concerned must be signed "not examined". The Seller shall have the right to inspect the goods at the Buyer’s premises in respect to any such claims made by the Buyer and the Buyer shall retain such goods until the Seller has inspected such goods or until the Seller has notified the Buyer that the

Seller does not wish to inspect such goods. Any breach of these conditions in this provision shall serve as a waiver to any claim brought by the buyer. (b) Without prejudice to the Seller’s other rights, should the Buyer fail for any reason to send the Seller forwarding instructions within ninety (90) days after the date of the Seller’s notification that the goods are ready for dispatch or to accept delivery of the goods, the Seller shall be entitled at the Buyer’s risk and expense to store the goods and/or to procure or effect storage of the goods elsewhere. Goods so stored shall be paid for as if they had been dispatched and/or accepted.

10. Special Tooling.

Where it is necessary for the Seller to manufacture or to purchase special tooling, including without limitation tools, dies, jigs, mandrills, fixtures, molds, and patterns, in order to execute a contract, the Buyer will be charged with all or a proportion of the cost of such special tools.

Such special tooling shall be and remain the Seller’s property notwithstanding payment of any charges made by the Buyer. In no event will the Buyer acquire any interest in apparatus belonging to the Seller which is utilized in the manufacture of the items sold hereunder, even if such apparatus has been specially converted or adopted for such manufacture and notwithstanding any charges paid by the Buyer therefore.

Unless otherwise agreed, the Seller shall have the right to alter, discard or otherwise dispose of any special tooling or other property in its sole discretion at any time.

11. Test and Performance.

(a) The Seller’s goods are, where practicable, submitted to the Seller’s standard test before delivery. If special tests are required, these shall be made at the Seller’s premises unless otherwise agreed, and will be subject to an extra charge. (b) The Seller accepts no liability for failure to attain any performance figures quoted by the Seller unless the Seller specifically has guaranteed them with an agreed sum as liquidation damages and the Buyer has suffered actual loss by reason of the failure to attain the figures quoted. (c) Any particulars of weights and measurements, power and consumption, power output or performance relating to the goods and like matters furnished by the Seller to the

Buyer in the Seller’s catalogs, literature or otherwise, are approximate and are intended only to present a general idea of the goods to be supplied and unless previously agreed specifically in writing shall not form part of the Agreement.

12. Buyer’s Property.

Any designs, tools, patterns, materials, drawings, confidential information or equipment furnished to the Seller by the Buyer, or any other items which become the Buyer’s property, may be considered obsolete and may be destroyed by the Seller after two (2) consecutive years have elapsed without the Buyer placing an order for the items which are manufactured using such property. The Seller shall not be responsible for any loss or damage to such property while it is in the Seller’s possession or control.

13. Taxes.

Unless otherwise indicated, all prices and charges are exclusive of excise, sales, use, property, occupational or like taxes which may be imposed by any taxing authority upon the manufacture, sale or delivery of the items sold hereunder. If any such taxes must be paid by the Seller, or if the Seller is liable for the collection of such tax, the amount thereof shall be in addition to the amounts for the item sold. The Buyer agrees to pay all such taxes or to reimburse the Seller therefore upon receipt of its invoice. If the Buyer claims exemption from any sales, use or other tax imposed by any taxing authority, the Buyer shall promptly indemnify and hold the Seller harmless from and against any such tax, as well as any interest or penalties thereon which may be assessed if the items are held to be taxable.

14. Warranty.

EXCEPT AS EXPRESSLY WARRANTED IN WRITING BY THE SELLER, THE GOODS SOLD BY THE SELLER ARE PURCHASED BY THE BUYER “AS IS.” THE

SELLER DOES NOT WARRANT THAT THE GOODS ARE OF MERCHANTABLE QUALITY OR THAT THEY CAN BE USED FOR ANY PARTICULAR PURPOSE.

EXCEPT AS EXPRESSLY WARRANTED IN WRITING BY THE SELLER, THE SELLER MAKES NO REPRESENTATION OR WARRANTY OF ANY KIND WITH

RESPECT TO THE PRODUCTS.

(a) The Seller warrants that the items sold hereunder shall be free from defects in material or workmanship at the time of shipment by the

Seller. The Seller warrants that if within 12 months of delivery of the goods to the Buyer the Buyer returns immediately to the Seller’s premises any of the said goods which the Buyer believes to be defective, carrier paid, properly packed and clearly marked with the Buyer’s full name and address and any other information such as serial numbers which may be necessary to enable the goods to be identified, together with a complete description of the alleged defect, they will be repaired or new goods will be supplied in exchange and the goods so repaired or such new goods will be delivered to the Buyer free of charge at the Seller’s premises; provided, however, that the foregoing warranty shall be applicable only if upon demand by the Seller, the Buyer proves to the Seller’s satisfaction: (i) that the defect was due solely to defective workmanship; (ii) that no alterations or repairs have been made to the goods except with the Seller’s written consent; (iii) that the defect was not caused by any act of the Buyer or its agents; and (iv) that the defect was not caused by any matter beyond the reasonable control of the

Seller, including, without limitation, accident or normal wear and tear. (b) THIS WARRANTY DOES NOT APPLY UNLESS THE SELLER’S PRODUCTS

ARE: (I) USED IN DOMESTIC PLUMBING APPLICATIONS; (II) INSTALLED BY A LICENSED CONTRACTOR, PLUMBER OR QUALIFIED EQUIPMENT

INSTALLATION PROFESSIONAL; AND (III) INSTALLED AND OPERATED IN ACCORDANCE WITH PUBLISHED HYDROFIT / HYDRONIX WATER

TECHNOLOGY SPECIFICATIONS. (c) All costs and expenses, including freight charges, customs duties, and insurance incurred in returning the goods to the Seller’s premises in accordance with this provision shall be paid by the Buyer. The benefit of this warranty shall not be assignable by the Buyer. (d) THIS WARRANTY DOES NOT EXTEND TO ANY GOODS NOT MANUFACTURED BY THE SELLER EVEN THOUGH SUPPLIED BY THE

SELLER NOR DOES IT EXTEND TO ANY SECOND-HAND OR RECONDITIONED GOODS NOR DOES IT EXTEND TO COMPONENTS MANUFACTURED BY THE

SELLER BUT INSTALLED, ATTACHED OR WELDED BY THE BUYER OR HIS CUSTOMER ON EQUIPMENT NOT MANUFACTURED BY THE SELLER. GOODS

NOT MANUFACTURED BY THE SELLER CARRY ONLY THE WARRANTY (IF ANY) OF THEIR MAKERS AND THE BUYER IS ENTITLED TO THE BENEFIT

THEREOF ONLY SO FAR AS THE SELLER HAS THE POWER TO TRANSFER IT. (E) THIS WARRANTY COMPRISES THE SOLE AND ENTIRE WARRANTY

PERTAINING TO ITEMS PROVIDED HEREUNDER; THE SELLER MAKES NO OTHER WARRANTY, GUARANTEE, OR REPRESENTATION OF ANY KIND

WHATSOEVER. ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO MERCHANTABILITY AND FITNESS FOR PURPOSE, WHETHER EXPRESSED

OR IMPLIED, OR ARISING BY OPERATION OF LAW, TRADE USAGE, OR COURSE OF DEALING, ARE HEREBY DISCLAIMED. (f) NOTWITHSTANDING

THE FOREGOING, THERE ARE NO WARRANTIES WHATSOEVER ON ITEMS BUILT OR ACQUIRED WHOLLY OR PARTIALLY TO THE BUYER’S DESIGNS

OR SPECIFICATIONS.

15. Limited Remedy.

THE SELLER’S LIABILITY ARISING FROM OR IN ANY WAY CONNECTED WITH THE ITEMS SOLD OR THIS AGREEMENT SHALL BE LIMITED EXCLUSIVELY

TO REPAIR OR REPLACEMENT OF THE ITEMS SOLD. IN NO EVENT SHALL THE SELLER BE LIABLE TO THE BUYER OR ANY THIRD PARTY FOR ANY

INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY KIND OR NATURE WHATSOEVER, INCLUDING BUT NOT LIMITED TO LOST PROFITS

ARISING FROM OR IN ANY WAY CONNECTED WITH THIS AGREEMENT OR ANY ITEMS SOLD, WHETHER ALLEGED TO ARISE FROM BREACH

OF CONTRACT, EXPRESS OR IMPLIED WARRANTY, OR IN TORT, INCLUDING WITHOUT LIMITATION, NEGLIGENCE, FAILURE TO WARN OR STRICT

LIABILITY. IN NO EVENT SHALL THE SELLER BE LIABLE TO THE BUYER OR ANY OTHER ENTITY FOR MORE THAN THE INVOICE PRICE RECEIVED BY THE

SELLER FOR ANY NON-CONFORMING PRODUCTS. THE SELLER SHALL NOT BE LIABLE TO THE BUYER OR ANY OTHER ENTITY FOR PERSONAL INJURY,

PROPERTY DAMAGE, OR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE, EXEMPLARY, SPECIAL, OR OTHER DAMAGES

OF ANY KIND, INCLUDING WITHOUT LIMITATION THE COST OF PROCUREMENT OF SUBSTITUTE GOODS, THE LOSS OF PROFITS, PRODUCTS, OR

PRODUCTION, OR THE INTERRUPTION OF BUSINESS, HOWEVER CAUSED. THE SELLER SHALL NOT BE LIABLE TO THE BUYER OR ANY OTHER ENTITY

ON ANY THEORY OF LIABILITY INCLUDING WITHOUT LIMITATION BREACH OF CONTRACT OR EXPRESS OR IMPLIED WARRANTY, TORT, NEGLIGENCE,

FAILURE TO WARN, OR STRICT LIABILITY, AND WHETHER OR NOT THE SELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE

ESSENTIAL PURPOSE OF THIS PROVISION IS TO LIMIT THE LIABILITY OF THE SELLER ARISING OUT OF THE SALE OF PRODUCTS TO THE BUYER

WHETHER FOR BREACH OF CONTRACT, NEGLIGENCE, OR ANY OTHER THEORY OF LIABILITY. THESE LIMITATIONS SHALL APPLY NOTWITHSTANDING

ANY FAILURE OF ESSENTIAL PURPOSE OF ANY LIMITED REMEDY AND NOTWITHSTANDING THE PROVISIONS OF ANY OTHER AGREEMENT BETWEEN

THE SELLER AND THE BUYER.

16. Indemnity for Infringement of Intellectual Property Rights.

(a) The Buyer shall defend and indemnify the Seller against all actions, claims, demands, penalties and costs by third parties in tort, or for infringement, or alleged infringement, of patents, trademarks, copyrights, trade dress, trade secret or other rights of any third party resulting from the goods manufactured in accordance with the Buyer’s specifications or based on any information provided by the Buyer. The Buyer will defend any action against the Seller for title, patent, trademark, copyright infringement, or other claimed by a third party at the Buyer’s sole cost and expense. (b) The Seller shall have no liability for infringement of any patents, trademarks, copyrights, trade dress, trade secrets or similar rights except as provided in this provision. The Seller will defend and indemnify the Buyer against allegations of infringement of patents, trademarks, copyrights, trade dress and trade secrets ("Intellectual Property Rights"). The Seller will defend at its expense and will pay the cost of any settlement or damages awarded in an action brought against the Buyer based on an allegation that an item sold pursuant to this contract infringes the Intellectual Property Rights of a third party. The Seller’s obligation to defend and indemnify the Buyer is contingent on the Buyer notifying the Seller within 10 days after sole control over the defense of any allegations or actions, including all negotiations for settlement or compromise. If an item sold hereunder is subject to a claim that it infringes the Intellectual Property Rights of a third party, the Seller may, at its sole expense and option, procure for the Buyer the right to continue using said item, replace or modify said item so as to make it non-infringing, or offer to accept return of said item and return the purchase price less a reasonable allowance for depreciation.

Notwithstanding the foregoing, the Seller shall have no liability for claims of infringement based on information provided by Buyer, or directed to items delivered hereunder for which the designs are specified in combination or use in a system of any item sold hereunder. The foregoing in this provision shall constitute the Seller’s sole and exclusive liability and the Buyer’s sole and exclusive remedy for infringement of Intellectual

Property Rights.

17. Lien.

In addition to any right of lien to which the Seller may by law be entitled, the Seller shall have a general lien on all goods of the Buyer in the

Seller’s possession (although such goods or some of them may have been paid for) for the unpaid price of any other goods sold and delivered to the Buyer by the Seller under the same or other contracts.

18. Waiver.

The Seller’s rights shall not be affected or restricted by any indulgence or forbearance granted to the Buyer. No waiver by the Seller of any breach shall operate as a waiver of any later breach.

19. Force Majeure.

The Seller shall be excused from performing any of its obligations under this Agreement which are prevented or delayed by any occurrence not within the reasonable control of the Seller, including but not limited to, accidents, acts of God, destruction or damage to the goods or the Seller’s manufacturing plant, delays or failures in delivery of carriers or suppliers, shortages of materials, strikes or other labor matters, floods, earthquakes, fire, riots, explosions, or any regulations, rules, ordinances or orders of any governmental authority, federal, state or local, whether such cause exists at the date of the order or not.

20. Buyer’s Representation of Solvency.

The Buyer hereby represents that as of the signing of this Agreement it was not insolvent within the meaning of the Uniform Commercial

Code or any Bankruptcy Laws.

21. Assignment and Delegation.

The rights and obligations of the parties under this Agreement may not be assigned or delegated, except on the express written consent of the other party to the assignment or delegation.

22. Integration.

The rights and obligations of the parties and the terms and conditions set forth herein, together with any amendments, modifications and any different terms and conditions expressly accepted by the Seller in writing, shall constitute a complete and exclusive statement of the terms of this Agreement. This Agreement supersedes not only all prior agreements, but also oral agreements made contemporaneously with the execution of this Agreement. All such materials may not be used to supplement, explain, or contradict the terms of this Agreement.

23. Severability.

If any of these conditions or any part thereof purports to exclude or restrict or limit any liability and such exclusion or restriction or limitation is prohibited or rendered void or unenforceable by any legislation to which it is subject, or is itself prohibited or rendered void or unenforceable by any legislation to which it is subject, then the exclusion, restriction or limitation on the condition or part thereof in question shall be so prohibited or rendered void or unenforceable and the validity or enforceability of any other part of these provisions shall not thereby be affected.

24. Governing Law/Limitation on Actions.

The terms, conditions, rights, and obligations under this Agreement shall be construed under the laws of the State of California, without regard to principles of conflicts of laws. No actions arising out of the sale of the items sold hereunder or this Agreement may be brought by the Buyer more than two (2) years after such cause of action accrues.

rea Glue A

FOLD HERE

Gate Fold Cover.indd 1

FOLD

HERE

OVERLAP FLIP 0.5”

Specifications

Part Number

UVA- 1C

UVA-2C

UVA-4C

UVA-6C

UVA-8C

UVA-12C

UVA-24B

UVA-36B

UVA-50B

UVA-60B

UVA-80B

UVA-100B

UVA-150B

UVA-200B

GPM

(LPM)

8

(30.28)

12

(45.42)

24

(90.85)

36

(136.27)

1

(3.8)

2

(7.57)

4

(15.14)

6

(22.71)

50

(189.27)

60

(227.12)

80

(302.83)

100

(378.54)

150

(567.81)

200

(757.08)

Rated Life

(hrs)

Lamp

Watts

9,000

9,000

9,000

9,000

9,000

9,000

9,000

9,000

9,000

9,000

9,000

9,000

9,000

9,000

10W

14W

17W

24W

32W

39W

39W

39W

39W

39W

39W

39W

87W

87W

Voltage at

50/60HZ

110V/220V

110V/220V

110V/220V

110V/220V

110V/220V

110V/220V

110V/220V

110V/220V

110V/220V

110V/220V

110V/220V

110V/220V

110V/220V

110V/220V

Visual

Warning

LED

LED

LED

LED

LED

LED

LED

LED

LED

LED

LED

LED

LED

LED

Audible

Warning

BUZZER

BUZZER

BUZZER

INDICATOR W/ ALARM

INDICATOR W/ ALARM

INDICATOR W/ ALARM

INDICATOR W/ ALARM

INDICATOR W/ ALARM

INDICATOR W/ ALARM

INDICATOR W/ ALARM

INDICATOR W/ ALARM

INDICATOR W/ ALARM

INDICATOR W/ ALARM

INDICATOR W/ ALARM

# of

Lamps

1

1

1

1

1

1

2

3

4

5

6

8

6

8

Port Size

I/O

1/4” MNPT

(.635 cm)

1/4” MNPT

(.635 cm)

1/2” MNPT

(1.270 cm)

1/2” MNPT

(1.270 cm)

3/4” MNPT

(1.905 cm)

3/4” MNPT

(1.905 cm)

1” MNPT

(2.540 cm)

1.5” MNPT

(3.810 cm)

1.5” MNPT

(3.810 cm)

2” or 2.5”

(5.080 or 6.350 cm)

FLANGE

2” or 2.5” MNPT

(5.080 or 6.350 cm)

FLANGE

2” or 2.5” MNPT

(5.080 or 6.350 cm)

FLANGE

3” MNPT

(7.62 cm) FLANGE

4” MNPT

(10.16 cm) FLANGE

Water

Chamber

STAINLESS 304

STAINLESS 304

STAINLESS 304

STAINLESS 304

STAINLESS 304

STAINLESS 304

STAINLESS 304

STAINLESS 304

STAINLESS 304

STAINLESS 304

STAINLESS 304

STAINLESS 304

STAINLESS 304

STAINLESS 304

-

















Timer

-

-

-

-

-

Length

10.47”

(26.594 cm)

13.74”

(34.900 cm)

15.50”

(39.37 cm)

23.23”

(59.00 cm)

27.87”

(70.79 cm)

36.81”

(93.50 cm)

36.93”

(93.80 cm)

36.93”

(93.80 cm)

36.93”

(93.80 cm)

36.93”

(93.80 cm)

36.93”

(93.80 cm)

36.93”

(93.80 cm)

36.93”

(93.80 cm)

36.93”

(93.80 cm)

Width

Max.

Pressure

125 PSI

8.79 kgF/cm 2

125 PSI

8.79 kgF/cm 2

125 PSI

8.79 kgF/cm 2

125 PSI

8.79 kgF/cm 2

125 PSI

8.79 kgF/cm 2

125 PSI

8.79 kgF/cm 2

125 PSI

8.79 kgF/cm 2

125 PSI

8.79 kgF/cm 2

125 PSI

8.79 kgF/cm 2

125 PSI

8.79 kgF/cm 2

125 PSI

8.79 kgF/cm 2

125 PSI

8.79 kgF/cm 2

125 PSI

8.79 kgF/cm 2

125 PSI

8.79 kgF/cm 2

2”

(5.080 cm)

2.5”

(6.350 cm)

2.5”

(6.350 cm)

2.5”

(6.35 cm)

2.5”

(6.35 cm)

2.5”

(6.35 cm)

3.5”

(8.89 cm)

5.5”

(13.97 cm)

5.5”

(13.97 cm)

5.5”

(13.97 cm)

6.26”

(15.90 cm)

8.62”

(21.90 cm)

8.62”

(21.90 cm)

8.62”

(21.90 cm)

Working

Temp.

35 o F 104 o F

(1.67

o C 40 o C)

35 o F - 104 o F

(1.67

o C 40 o C)

35 o F - 104 o F

(1.67

o C 40 o C)

35 o F - 104 o F

(1.67

o C 40 o C)

35 o F - 104 o F

(1.67

o C 40 o C)

35 o F - 104 o F

(1.67

o C 40 o C)

35 o

(1.67

F - 104 o o C 40

F o C)

35 o F - 104 o F

(1.67

o C 40 o C)

35 o F - 104 o F

(1.67

o C

-

40 o C)

35 o F - 104 o F

(1.67

o C 40 o C)

35 o F - 104 o F

(1.67

o C 40 o C)

35 o F - 104 o F

(1.67

o C 40 o C)

35 o F - 104 o F

(1.67

o C 40 o C)

35 o F - 104 o F

(1.67

o C

-

40 o C)

Wavelength Microjoules

254 nm

254 nm

254 nm

254 nm

254 nm

254 nm

254 nm

254 nm

254 nm

254 nm

254 nm

254 nm

254 nm

254 nm

30 mJ/cm

30 mJ/cm

30 mJ/cm

30 mJ/cm

30 mJ/cm

30 mJ/cm

30 mJ/cm

30 mJ/cm

30 mJ/cm

30 mJ/cm

30 mJ/cm

30 mJ/cm

30 mJ/cm

30 mJ/cm

2

2

2

2

2

2

2

2

2

2

2

2

2

2

Part Number

UVA- 1C

UVA-2C

UVA-4C

UVA-6C

UVA-8C

UVA-12C

UVA-24B

UVA-36B

UVA-50B

UVA-60B

UVA-80B

UVA-100B

UVA-150B

UVA-200B

Parts & Accessories

Lamp

GL39PP

GL39PP

GL39PP

GL39PP

GL87PP

GL87PP

GL10PP

GL14PP

GL17PP

GL24PP

GL32PP

GL39PP

GL39PP

GL39PP

< 1 NTU

> 75%

Quartz Sleeve

QS39

QS39

QS39

QS39

QS39

QS39

QS10

QS14

QS17

QS24

QS32

QS39

QS39

QS39

Water Quality

Water quality plays a major role in the transmission of germicidal ultraviolet rays. It is recommended that the water does not exceed the following maximum concentration levels.

Maximum Concentration Levels

Iron

Hardness

Turbidity

Manganese

Tannins

UV Transmittance

< 0.3 ppm (0.3 mg/L)

< 7 ppm (120 mg/L)

< 0.05 ppm (0.05 mg/L)

< 0.1 ppm (0.1 mg/L)

Effectively treating water with higher concentration levels than listed above can be accomplished, but may require added measures to improve water quality to treatable levels.

Electronic Ballast

BEB-1024

BEB-1024

BEB-1024

BEB-2439

BEB-2439

BEB-2439

ZEB-2439

ZEB-2439

ZEB-2439

ZEB-2439

ZEB-2439

ZEB-2439

ZEB-55155

ZEB-55155

UV-NUT-1

UV-NUT-1

UV-NUT-1

UV-NUT-1/ UV-NUT-2

UV-NUT-1/ UV-NUT-2

UV-NUT-1/ UV-NUT-2

UV-NUT-1/ UV-NUT-2

UV-NUT-1/ UV-NUT-2

UV-NUT-1/ UV-NUT-2

UV-NUT-1/ UV-NUT-2

UV-NUT-1/ UV-NUT-2

UV-NUT-1/ UV-NUT-2

UV-NUT-1/ UV-NUT-2

UV-NUT-1/ UV-NUT-2

Additional Accessories Specific to Your UV System

-

-

-

-

UV-32 SPRING

UV-39 SPRING

UV-39 SPRING

UV-39 SPRING

UV-39 SPRING

UV-39 SPRING

UV-39 SPRING

UV-39 SPRING

UV-39 SPRING

UV-39 SPRING

-

-

-

-

-

-

UV-TIMER

UV-TIMER

UV-TIMER

UV-TIMER

UV-TIMER

UV-TIMER

UV-TIMER

UV-TIMER

UV-SEAL

UV-SEAL

UV-SEAL

UV-SEAL

UV-SEAL

UV-SEAL

UV-SEAL

UV-SEAL

UV-SEAL

UV-SEAL

UV-SEAL

UV-SEAL

UV-SEAL

UV-SEAL

UV-WASHER

UV-WASHER

UV-WASHER

UV-WASHER

UV-WASHER

UV-WASHER

UV-WASHER

UV-WASHER

UV-WASHER

UV-WASHER

UV-WASHER

UV-WASHER

UV-WASHER

UV-WASHER

UV Dose

The units generate a UV dosage of at least 30,000 microwatt-seconds per square centimeter

(µW-s/cm

2

), even at the end-of-lamp life (EOL), which is more than sufficient to destroy most waterborne microorganisms, such as bacteria, yeasts, algae, etc.

UV disinfection is affected by many factors and the following should be looked at prior to the installation of the UV system; UV Transmission

(transmittance) deals with the effectiveness in which the 2537 Angstrom units (254 nanometers) wavelength of the ultraviolet light is transmitted through the water. The higher the transparency of the water, the more effective the UV system becomes. This optical clarity is evaluated by performing a test which passes through a 1 cm depth.

The basic design of the units has taken into account a typical transmission at the desired wavelength. In practical terms this means that a system designed to flow at 24 gallons per minute, at a typical transmissibility could actually have a higher flow rate in liquids with a higher transmissibility. As a general guideline, the following are some typical UV transmission rates (UVT):

City water supplies

Deionized or RO water

85-98%

95-98%

Surface waters (lakes, rivers, etc) 70-90%

Ground water (wells) 90-95%

Other liquids 1-99%

-

-

-

UV-PLUG

UV-PLUG

UV-PLUG

UV-PLUG

UV-PLUG

UV-PLUG

UV-PLUG

UV-PLUG

UV-PLUG

UV-PLUG

UV-PLUG

LIT-PSUV-CAT16 05/25/16

Product Ratings

RoHS

COMPLIANT

Warranty Information

• Limited 5-year warranty on stainless steel housing

• Limited 1-year warranty on electronics

Distributed by:

P.O. Box 2235

Chino Hills, CA 91709 USA

©2016 POLARIS SCIENTIFIC UV. All Rights Reserved.

FOLD

HERE

Cut Guide

Folding Guide

5/25/16 12:49 PM