VETUS HRC10 series Manual

HRC10

Rope/Chain Windlass

VETUS

–MAXWELL APAC Ltd

Owner Note:

Record your serial Number here.



Copyright VETUS-Maxwell APAC Ltd. All rights reserved

VETUS-Maxwell APAC Ltd reserves the right to make

engineering refinements on all products without notice.

Always consult manual supplied with product as details may have been revised.

Illustrations and specifications are not binding as to detail.

P103124 rev. 3.00 10/10/17

INTRODUCTION



Read this manual thoroughly before installation and using the windlass. Failure to adhere to the correct procedures, recommendations and guidelines described in this Owner’s Manual may invalidate the warranty.



Correct selection of windlass together with correct installation, care in use and maintenance, are essential for long life and reliable performance.



In addition to this instruction manual, the following components should be included with the windlass:



Clutch Handle.



Bi-Square to ½ socket adaptor.



Deckplate Gasket.



Deck Cutout Details (at rear of manual)



Deck stud Kit.

- 4 x Studs

- 4 x Nuts

- 4 x Flat washers

- 4 x Spring washers

The following accessories may be required to complete your installation:



Remote up/down control panel



Circuit breaker/isolator panel



12V or 24V reversing solenoid

IMPORTANT INFORMATION



The windlass must have a minimum pull capacity of three times the combined weight of the anchor and rope/chain.



Keep hands, feet, loose clothing and hair well clear of the windlass and rope/chain during operation.



Never operate the windlass from a remote station without having a clear view of the windlass.



Do NOT use the windlass as a mooring point. When anchoring or mooring, secure the line directly to a bollard or deck cleat.



Do NOT use the windlass to pull the boat forward when raising the anchor. Use the boat's engine to drive the boat up to the anchor.



Do NOT attempt to break free a fouled anchor with the windlass. Secure the line to a bollard or cleat and use the boat's engine to break the anchor out.



Always firmly tie down the anchor when under way or in heavy seas. Do not rely on the windlass as a securing device.



Always turn the circuit breaker/isolator switch off when the windlass is not in use and before you leave the boat.



Do NOT use the windlass to haul a person up a mast.

ROPE AND CHAIN SELECTION

Correct fit of rope and chain to chainwheel is essential for the windlass to operate properly.

The ground tackle should be selected taking into account: a) Boat size, displacement and windage. b) Conditions of operation such as maximum depth of water, type of bottom and likely weather conditions. c) Holding power and size of anchor, taking special note of the manufacturers’ recommendations.

Selection of chainwheel:

Part Number P103315 for :

HRC108: 14mm (9/16”)-16mm (5/8”) rope / 8mm (5/16”) chain

Part Number P103316 for :

HRC10-10: 16mm (5/8”) rope / 10mm (3/8”) chain

INSTALLATION



For automatic operation to be possible, the anchor must be self launching.



Tie the end of the anchor rope/chain to a secure fixture in the rope/chain locker.



Foredeck layout

Ensure the deck is flat, if not; a plinth (A) will be required to ensure the windlass sits on a flat surface.

A

Required clearances

Identify any bulkheads, wiring or piping under the deck that should be avoided.

Position the windlass so the rope/chain falls directly into the rope/chain locker with at least

200mm (8”) unobstructed fall.

VETUS-Maxwell APAC Ltd HRC10 Series 1

Aligning the windlass

The windlass must be positioned to allow the rope/chain to have a clear run from the bow roller (B) to the chainwheel without deflection.

The windlass must be mounted pointing in the direction of the incoming rope/chain. This arrangement allows the rope/chain to have maximum engagement with the chainwheel.

B

Installation Procedure

B

Use the Deck Cutout Details drawing, as a guide for marking and cutting the holes.

Tip : On GRP boats, running the drill in reverse first will reduce chipping of the gel coat.

Using hole saws, cut the holes for the rope/chain pipe and electrical cables.

On GRP or wooden decks, seal the edges of the holes with epoxy to avoid ingress of moisture.

Install deck studs to windlass and tighten by use of two nuts. Place the gasket onto the windlass and fit to deck.

Fasten the windlass to the deck using the nuts and washers supplied. Tighten the nuts progressively and evenly. Do NOT use power tools. Make sure the installation is firm, but do not over tighten the nuts.

Important note to Boat Builders

Experience has shown that, on long ocean deliveries as deck cargo, sulphur from the ships exhaust and condensation can damage the chrome plating and stainless steel of the windlass.

We recommend, after completing installation, you spray the top works of the windlass with CRC 3097 “long life” (or alternative) and wrap the windlass with plastic film and tape.

WIRING INSTRUCTIONS

Installation must be carried out in accordance with USCG,

ABYC, NMMA, CE or other relevant local electrical requirements.

We recommend that connection of the power lines and control circuitry to the windlass be done by qualified technicians, to ensure reliable and safe operation of the windlass.

After all connections have been made and system tested, seal terminals against moisture by spraying with:

CRC2043 “Plasti-Coat”, CRC3013 “Soft Seal” or CRC2049

“Clear Urethane” (or alternative).

Solenoid pack (Required)

The solenoid pack (B) should be located in a dry area close to the windlass, not in the rope/chain locker.

Circuit breaker/isolator (Required)

!

FOR SAFETY - The winch circuit requires protection provided by an isolator switch and

either a fuse or circuit breaker, rated as follows:

HRC10-12V : 135amp

HRC10-24V : 80amp

Position the circuit breaker/isolator (C) no further than 1.8 m (6 ft) away from the battery (D) in an accessible and dry location.

Remote control panel (Recommended)

The remote control panel (E) should be mounted in a convenient location (such as the bridge, helm or cockpit) so that the operator can see the windlass.

Footswitch (Optional).

For safe operation, the footswitch (F) should be approximately 500 mm (20") from the windlass (A).

The below-deck part of the footswitch must be in a dry environment and the breather holes must be kept clear.

The arrows on the footswitch should be arranged to indicate the direction of operation.

Fit the switch according to the instructions supplied.

Connect wiring as shown.

Motor

When tightening the cables to the motor, ensure the lower nut (A) is secure against turning when tightening the upper nut (B). This will prevent damage occurring within the motor. Nut(B) should be tightened to 9-11Nm.

A B

2 HRC10 Series VETUS-Maxwell APAC Ltd

OPERATION

CAUTION:

Make sure that you do not operate the footswitch accidentally while putting extra turns on the capstan.

Keep your fingers clear of the chainwheel and/or capstan.

When operating the windlass:

-Ensure the pawl is in the disengaged position when paying out the anchor.

Raising the Anchor Manually:

Move the pawl into the engaged position.

Pawl In Disengaged position

-Do not switch immediately from one direction to the other.

Wait for the windlass to stop in one direction before applying power in the other direction.

-

Run the boat’s motor(s) at sufficient rpm to activate the charging system.

Always make sure the isolator switch is turned off when the system is not being used.

Lowering the Anchor

Insert the clutch handle into the clutch nut and tighten the clutches by turning the nut clockwise. Only tighten sufficiently so that you can easily pull up the anchor.

REMOVE THE CLUTCH HANDLE.

Operate the windlass by pressing the toggle switch down on the remote up/down control panel to pay out the rope/chain (or press the "Down" footswitch if fitted).

Pay out sufficient rope/chain to set the anchor.

Watch as the rope/chain is being fed out. Any jam might cause damage to the windlass.

Raising the Anchor

Insert the clutch handle into the clutch nut and tighten the clutches by turning the nut clockwise. Only tighten sufficiently so that you can easily pull up the anchor.

REMOVE THE CLUTCH HANDLE. NOTE: Over tightening the clutches can cause damage to the motor when docking the anchor.

Operate the windlass by pressing the toggle switch up on the remote up/down control panel (or press the "Up" footswitch if fitted).

Motor up to the anchor while retrieving it. Do not use the windlass to pull the boat to the anchor.

To avoid damaging the bow fitting, retrieve the last meter

(3’) of rope/chain slowly and take care when docking the anchor.

Note: To avoid applying the full force of the windlass to the bow fitting when docking the anchor, adjust the clutch nut so that there is some slippage when docking the anchor.

Free falling the Anchor

Insert the clutch handle into the clutch nut and loosen by slowly turning the handle anticlockwise.

Tightening the clutch nut clockwise will control the rate of descent.

CAUTION: Do not allow the chainwheel to free wheel uncontrolled as this will allow dangerously high speeds to build up.

VETUS-Maxwell APAC Ltd HRC10 Series

Insert the clutch handle into the clutch nut and turn anticlockwise to loosen the clutch. Note the chain wheel may pay out the anchor until the pawl locks into the chainwheel.

Insert the clutch handle into the outer bi-square of the chainwheel and rotate anticlockwise to pull in the line. A bisquare to ½” socket adaptor has been provided with your windlass. This can be used with any ½” ratchet to recover the rode.

Using the Capstan Drum for Rope Warping:

The capstan can be used independently from the chainwheel. This is ideal for handling mooring or docking lines, or retrieving a second anchor. For safety reasons, a footswitch is highly recommended.

To haul in using the capstan:

Make sure the anchor is secured.

Insert the clutch handle into the clutch nut and turn anticlockwise until rotation stops. This will release the mechanism so that the chainwheel remains stationary while you operate the capstan.

Take three turns of rope around the drum in a clockwise direction.

While holding the tail of the rope, press the "Up" footswitch. The capstan will rotate clockwise.

3

MAINTENENCE

Every Trip



Ensure clutch is adjusted correctly



Wash down topworks with fresh water



Spray motor and electrical connections with CRC

Soft Seal.



Check rope for wear and wash down with fresh water

Every 3 Months



Remove chainwheel. Strip and grease clutch



Split gearbox (1) from main case (2), clean and regrease mating faces.

2 1



Check level of oil in gearbox using the sight glass

(3). Oil level (4) should be above ½ and no more than ¾ full. If necessary top up.

3 4



Clean the Windlass with a cloth damp with

Kerosene (paraffin). Spray preferably with

CRC3097 “Long Life” or alternatively, CRC6-66 or

WD40 (or alternative). Polish off with a clean nonfluffy cloth.

Every Year



The motor should be serviced by a qualified technician.



Remove any rust build up from the casing and paint with a suitable coating

Every 3 Years



The gearbox should be serviced by an authorised service agent.

Specifications

Electric Motor : Direct Current motor

Voltage : 12 V DC or 24 V DC

Rated Output : HRC10-8: 1000W

: HRC10-10: 1200W

Hydraulic Motor:

Recommended Flow :20l/min 5.3gal/min

Relief Valve setting :2000 psi 138bar

Gear box ratio : 56:1

Max Force : HRC10-8: 700kg (1540 lbs)

: HRC10-10: 850kg (1870 lbs)

Haulage speed : 20-24 m/min (65.6-78.7 ft/min)

(Dependant on the load)

Rope size : HRC10-8: 14-1 6mm (9/16”-5/8”)

: HRC10-10: 16mm ( 5/8”)

Chain size : HRC10-8: 8mm (5/16”) short link

: HRC10-10:10mm (3/8”) short link

: HRC10-8: 19kgs (42lbs)

: HRC10-10: 20kgs (44lbs)

Net weight

4 HRC10 Series VETUS-Maxwell APAC Ltd

Recommended lubricants:

Gearbox :

Capacity: 75 ml (2.4 fl oz)

SAE viscosity grade 90-110 API GL-4 or lower gear oil

Main shaft, bearing, and clutch surfaces:

Marine grease, Lithium or Lithium complex

based NLGI No.1 to No.3 .Do not use soap based greases.

WARNING:

When re-assembling care must be taken to ensure the

key/keys are properly seated in the shaft.

DO NOT wrap the motor with grease cloth as this

prevents the cooling of the motor.

Ordering Spare Parts

When ordering spare parts, please quote the following details.

Windlass Model_________________

Serial number __________________

Power supply___________________

Note: For your nearest retailer, service agent or representative please refer to our website www.maxwellmarine.com

Cable Lengths

12V Systems

Cable Length

Up to 12m (40')

12m - 16m (40' - 52')

16m - 20m (52' - 65')

20m - 26m (65' - 85')

66m - 33m (85' - 108')

24V Systems

Cable Size mm² AWG

25

35

3

2

50

70

70

1

0

00

Cable Length

Cable Size mm² AWG

Up to 27m (88') 16 6

27m - 43m (88' - 141') 25 4

!

NOTE: Cable length is the total length from battery to winch then back to battery.

VETUS-Maxwell APAC Ltd HRC10 Series 5

Overall Dimensions

6 HRC10 Series VETUS-Maxwell APAC Ltd

Parts List

VETUS-Maxwell APAC Ltd HRC10 Series 7

Parts List

8 HRC10 Series VETUS-Maxwell APAC Ltd

Item no. Component Description

1 Capscrew M6x16

2

3

Washer M6x16

Clutch nut

4

5

6

7

8

9

Clutch cone upper

Belleville Washer

Capscrew M5x12

Chainwheel outer 8mm

Chainwheel outer 10mm

Stripper

Chainwheel inner 8mm

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

Chainwheel inner 10mm

Belleville Washer

Clutch cone Lower

Shaft

Shaft (No Drum Version)

Pressure arm

Pressure arm spring

Capscrew M6 x 70

Spring Washer

Chain Pipe

Key

Quad Ring

Plug

Bush

Deckplate Bearing

Capscrew M10x20

Spacer

Pawl

Washer M12

Gasket

Nut M10

Spring washer M10

Washer M10

Stud M10x125mm

Main Case

Circlip 1-1/8"SS

Drum SS

Retaining washer

Screw Csk slot M8

Cap

Cover (No Drum version only)

O-ring 178 x3

Bolt M8x20

Spring Washer M8

Washer M8

Bolt M8x25

VETUS-Maxwell APAC Ltd HRC10 Series

1

1

1

1

1

1

1

1

2

1

3

1

1

3

1

1

1

1

1

1

1

1

1

1

Qty

1

1

1

1

1

3

4

2

4

4

1

1

1

1

1

1

1

1

4

4

4

4

P104724

7347

7037

SP4509

SP0474

7346

6340

SP2758

SP3519

SP3518

4218

SP0194

7400

7362

SP0424

7395

Parts to order

SP0167

SP0439

6914C

6090

SP0484

SP4503

P103315

P103316

6915

P103315

P103316

SP0488

Ref #12

P104723

SP0064

3465

7401

SP2798

SP0254

SP0467

SP0413

P12487

SP0371

SP0466

SP0423

5225

7344

SP0878

7502

3467

1,2,11,12,19

Includes

6,7,8,9

6,7,8,9

6,7,8,9

6,7,8,9

1,2,11,12,19

42,43,44,46

9

44

45

46

47

48

57

58

53

54

55

56

49

50

51

52

Spring Washer M8

Washer M8

Gearbox 56:1

O-Ring

Motor 12V 1000W

Motor 12V 1200W

Motor 24V 1200W

Motor Cover

Capscrew M6 x 25

Label

Capscrew M6 x 45

Bolt

Washer M8

Motor Hydraulic

Washer M8

Spring Washer M8

Nut M8

Bi-Square to 1/2" drive adaptor

Bi-Square handle 8"

Product Manual

1

2

2

2

1

2

1

2

1

1

1

1

2

2

1

2

2

P12487

P12487

P12436

P12487

P12072

P12073

P12074

7345

SP0175

7361

SP4511

P12488

P12488

P14366

P12488

P12488

P12488

7369

P103864

P103124

42,43,44,46

42,43,44,46

42,43,44,46

52,53,55,56,57

52,53,55,56,57

52,53,55,56,57

52,53,55,56,57

52,53,55,56,57

10 HRC10 Series VETUS-Maxwell APAC Ltd

Electrical and Hydraulic Schematic

Series Wound Motor

1 Remote control panel

2 Down Foot Switch

3 Up Foot Switch

4 Breaker/Isolator

5 Battery

6 Motor

7 Manually resettable breaker

8 Solenoid Pack

Hydraulic Motor

1 Remote control panel

2 Down Foot Switch

3 Up Foot Switch

4 Breaker/Isolator

5 Battery

6 Motor

7 Dual direction solenoid

8 Relief Valve

9 Pump

10 Tank

VETUS-Maxwell APAC Ltd HRC10 Series 11

12 HRC10 Series VETUS-Maxwell APAC Ltd

VETUS-Maxwell APAC Ltd HRC10 Series 13

14 HRC10 Series VETUS-Maxwell APAC Ltd

LIMITED WARRANTY

Warranty: VETUS-Maxwell APAC Ltd provides a three year limited warranty on windlasses for pleasure boat usage, and a one year limited warranty for those systems used on commercial or charter vessels. Warranty, service and parts are available around the world. Contact your nearest VETUS-Maxwell office for a complete list of service centres and distributors.

This warranty is subject to the following conditions and limitations:

1. This Warranty will be null and void if (a) there is any neglect or failure to properly maintain and service the products.

(b) the products are serviced, repaired or maintained improperly or by unauthorised

2. persons.

(c) loss or damage is attributed to any act, matter or omission beyond the reasonable control of VETUS-Maxwell or the purchaser.

VETUS-Maxwell liability shall be limited to repair or replacement (as determined by VETUS-Maxwell) of the goods or parts defective

3.

4.

5. in materials or workmanship.

Determination of the suitability of the product and the materials for the use contemplated by the buyer is the sole responsibility of the buyer, and VETUS-Maxwell shall have no responsibility in connection with such suitability.

VETUS-Maxwell shall not be liable for any loss, damages, harm or claim attributed to:

(a) use of the products in applications for which the products are not intended.

(b) corrosion, wear and tear or improper installation.

(c) improper use of the product.

This Warranty applies to the original purchaser of the products only. The benefits of the Warranty are not transferable to

6.

7. subsequent purchasers.

VETUS-Maxwell shall not be responsible for shipping charges or installation labour associated with any warranty claims.

There are no warranties of merchantability, fitness for purpose, or any other kind, express or implied, and none shall be implied by law. If any such warranties are nonetheless implied by law for the benefit of the customer they shall be limited to a period of three

8. years from the original purchase by the user.

VETUS-Maxwell shall not be liable for consequential damages to any vessel, equipment, or other property or persons due to use or installation of VETUS-Maxwell equipment.

This Warranty sets out your specific legal rights allowed by VETUS-Maxwell; these may be varied by the laws of different countries. 9.

In addition, the purchaser may also have other legal rights which vary from country to country.

10. To make a claim under this Warranty, contact your nearest VETUS-Maxwell office or distributor. Proof of purchase and authorisation from VETUS-Maxwell will be required prior to any repairs being attempted.

Purchaser

To be eligible for warranty protection, please either complete the form below at the time of purchase and return it to the appropriate retailer or supplier of the goods, or fill out the electronic warranty form on our website, www.maxwellmarine.com

Address: Name:

Telephone: Facsimile

Supplier / Dealer

Name:

Telephone:

Windlass Model

Date of Purchase

Name

Built by

Facsimile

L.O.A.

Address:

Serial Number

Boat Type Windlasses Supplied

With boat

Fitted by boat yard/dealer

Purchased from dealer/chandler

VETUS-Maxwell APAC Ltd HRC10 Series 15

16 HRC10 Series VETUS-Maxwell APAC Ltd