Zebra LS4278 Quick Reference Guide

LS4278

Quick Reference Guide

2 LS4278

© 2015 Symbol Technologies, Inc.

Zebra reserves the right to make changes to any product to improve reliability, function, or design.

Zebra does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.

No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Zebra products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Zebra products.

Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra Technologies company.

Zebra Technologies Corporation

Lincolnshire, IL U.S.A.

http://www.zebra.com

Warranty

For the complete Zebra hardware product warranty statement, go to: http://www.zebra.com/warranty

Quick Reference Guide 3

Introduction

The LS4278 scanner combines excellent scanning performance and advanced ergonomics to provide the best value in a lightweight laser scanner. Whether used as a hand-held scanner or in hands-free mode in a stand, the scanner ensures comfort and ease of use for extended periods of time. Before programming the scanner, scan the appropriate bar code(s), beginning on

page 8

, to communicate with the host.

Parts

Scan

Window

Scan

Trigger

LED

Beeper

Battery Insertion/Removal

1 2 3

Connect

4 5 6

4

Scanner Insertion in Cradle

Table Top

Wall Mount

hook facing up

Aiming

65 o

65 o

LS4278

Quick Reference Guide

Scanning

012345

5

012345

012345

012345

Beeper Definitions

The scanner issues different beep sequences and patterns to indicate status. The table below defines beep sequences that occur during both normal scanning and while programming the scanner.

Indication Beeper Sequence

Standard Use

Low/medium/high beeps

High beep

Four long low beeps

Five low long beeps

Low/high/low beeps

High/high/high/low beeps

Parameter Menu Scanning

Long low/long high beeps

Power up.

A bar code symbol was decoded (if decode beeper is enabled).

A transmission error was detected in a scanned symbol.

The data is ignored. This occurs if a unit is not properly configured. Check option setting.

Conversion or format error.

ADF transmit error.

RS-232 receive error.

High/low beeps

High/low/high/low beeps

Long low/long high/long low/long high beeps

Wireless Operation

High/low/high/low beeps

Low/high beeps

Input error, incorrect bar code or “Cancel” scanned, wrong entry, incorrect bar code programming sequence; remain in program mode.

Keyboard parameter selected. Enter value using bar code keypad.

Successful program exit with change in the parameter setting.

Out of host parameter storage space. Scan Set Defaults on page 8

.

Pairing bar code scanned.

Bluetooth connection established.

6 LS4278

Beeper Sequence

High/low beeps

Long low/long high beeps

Long low/long high/long low/long high beeps

Code 39 Buffering

High/low beeps

Three long high beep

Low/high/low beeps

Indication

Bluetooth disconnection event.

Page timeout; remote device is out of range/not powered.

Connection attempt was rejected by remote device.

New Code 39 data was entered into the buffer.

Code 39 buffer is full.

The Code 39 buffer was erased or there was an attempt to clear or transmit an empty buffer.

A successful transmission of buffered data.

Low/high beeps

Host Specific

USB only

Four high beeps

Scanner gives a power-up beep after scanning a USB Device Type.

This power-up beep occurs more than once.

RS-232 only

High beep

Scanner has not completed initialization. Wait several seconds and scan again.

Communication with the bus must be established before the scanner can operate at the highest power level.

The USB bus may put the scanner in a state where power to the scanner is cycled on and off more than once. This is normal and usually happens when the host PC cold boots.

A <BEL> character is received and Beep on <BEL> is enabled.

LED Definitions

In addition to beeper sequences, the scanner communicates with the user using a two-color LED display. The table below defines LED colors that display during scanning and charging.

Scanning LED

Green Flash

Charging LED

Green - Slow Continuous Flash

Green - Fast Continuous Flash

Green - Solid

Amber - Continuous Flash

Indication

A bar code was successfully decoded.

Indication

Non-critical battery temperature fault.

Scanner is charging.

Scanner is fully charged.

Critical battery temperature fault.

Quick Reference Guide

Troubleshooting

Problem

LED indicates a battery temperature fault.

Nothing happens when the trigger is pulled.

Possible Cause

Battery is above or below normal operating temperature.

No power to the scanner.

Scanner is disabled.

Laser comes on, but symbol does not decode.

Symbol is decoded but not transmitted to the host.

Scanner is not programmed for the correct bar code type.

Bar code symbol is unreadable.

Distance between scanner and bar code is incorrect.

Cradle is not programmed for the correct host interface.

Scanner not paired to host-connected interface.

Interface cable is loose.

Cradle has lost connection to host.

Scanned data is incorrectly displayed on the host.

Possible Solutions

Do not use the scanner. Move the scanner to a location within normal operating temperature.

The scanner can remain in the cradle while the battery warms or cools to normal operating temperature. Refer to the Product Reference

Guide for more information.

Battery may be discharged; charge scanner in cradle.

Check that battery door is closed

Ensure that end cap to battery chamber is secured.

Some host interfaces (e.g., Synapse, IBM-468x) can disable the scanner. If this applies, enable the scanner via the host interface.

Ensure the scanner is programmed to read the type of bar code scanned.

Refer to the Product Reference Guide for more information.

Check the symbol to ensure it is not defaced. Try scanning test symbols of the same bar code type.

Move the scanner closer to or further from the bar code.

Check scanner host parameters or edit options.

Pair the scanner to the cradle (using PAIR bar code on the cradle).

Ensure all cable connections are secure.

Scanner is not programmed to work with the host.

In this exact order: disconnect power supply; disconnect host cable; wait three seconds; reconnect host cable; reconnect power supply; reestablish pairing.

Ensure proper host is selected.

Check the scanner’s host type parameters or editing options.

For RS-232, ensure the scanner’s communication parameters match the host’s settings.

For a keyboard wedge configuration, ensure the system is programmed for the correct keyboard type, and the CAPS LOCK key is off.

Ensure editing options (e.g., UPC-E to UPC-A conversion) are properly programmed.

Refer to the Product Reference Guide for more information.

7

8 LS4278

Programming Bar Codes

Following are some frequently used programming bar codes.

NOTE For additional host types, refer to the LS4278 Product Reference

Guide , p/n 72E-69834-xx, available on the website: http://www.zebra.com/support .

Set Defaults

Scan SET DEFAULTS to set all parameters to their default values.

SET DEFAULTS

Scanning Modes

Scan the appropriate bar code below to determine the scanning pattern.

• SINGLE LINE ONLY - No up and down scan line movement (no raster).

• MULTI-LINE SMART RASTER - The scan line begins as a single line and moves up and down (rasters) when a partial scan of a bar code is detected, or no bar code is decoded 500 ms after the trigger is pulled.

• MULTI-LINE ALWAYS RASTER (default) - Rastering (up and down scan line movement) begins immediately.

SINGLE LINE ONLY

MULTI-LINE SMART RASTER

MULTI-LINE ALWAYS RASTER (Default)

Quick Reference Guide 9

Host Types

If a Synapse cable is used (i.e., part number STIxx-xxxx), the scanner autodetects the Synapse cable and there is no need to scan bar codes to enable the Synapse host.

If a USB interface is used, the scanner autodetects the USB and defaults to the

HID keyboard interface. See

page 12

to select the IBM hand-held host type.

If a Keyboard Wedge, RS-232, Wand Emulation, Scanner Emulation, or IBM

46XX is used, the appropriate host type must be scanned. Select the appropriate host type from the bar codes that follow.

Keyboard Wedge Host Type

IBM PC/AT and IBM PC COMPATIBLES

Country Keyboard Types (Country Codes)

NORTH AMERICAN (Default)

FRENCH Windows

FRENCH CANADIAN Windows 95/98

FRENCH CANADIAN Windows XP/2000

10

Country Keyboard Types (Country Codes)

GERMAN Windows

LS4278

SPANISH Windows

ITALIAN Windows

SWEDISH Windows

UK ENGLISH Windows

JAPANESE Windows

PORTUGUESE-BRAZILIAN Windows

Quick Reference Guide

RS-232 Host Types

STANDARD RS-232

ICL RS-232

NIXDORF RS-232 MODE B

NIXDORF RS-232 MODE A

11

FUJITSU RS-232

USB Host Types

OPOS/JPOS

HID KEYBOARD EMULATION

IBM HAND-HELD USB

12

IBM 46XX Host Types

LS4278

PORT 5B

PORT 9B

Wand Emulation Host Type

SYMBOL WAND

Many Wand hosts require input as Code 39 data. Scan the following bar codes to enable or disable transmission of data to the Wand host as Code 39 data.

ENABLE CONVERT TO CODE 39 FOR WAND HOST

DISABLE CONVERT TO CODE 39 FOR WAND HOST (Default)

Scanner Emulation Host Type

Scan the bar code below to enable the Scanner Emulation host.

ENABLE SCANNER EMULATION HOST

Quick Reference Guide 13

Radio Communications Host Types

Scan a bar code below to choose how the scanner connects to a remote device.

Scan Cradle Host if connecting to the STB4278 cradle.

CRADLE HOST

SERIAL PORT PROFILE (MASTER)

SERIAL PORT PROFILE (SLAVE)

BLUETOOTH KEYBOARD EMULATION

(HID SLAVE)

Pairing

When the scanner is configured as an SPP or HID Master, a 'pairing bar code' must be created for the remote Bluetooth device to which the scanner can connect. The Bluetooth address of the remote device must be known. Pairing bar codes are Code 128 bar codes. The format is: <Fnc 3>Bxxxxxxxxxxxx (where xxxxxxxxxxxx represents the 12-character Bluetooth address).

Pairing Modes

When operating with the cradle, two modes of pairing are supported:

• Locked Pairing Mode - When a cradle is paired (connected) to the scanner, any attempt to connect to a different scanner, by scanning the pairing bar code on the cradle or by inserting it into the cradle with Pairing on Contacts enabled, is rejected. The currently connected scanner maintains its connection.

• Unlocked Pairing Mode - A new scanner can be paired (connected) to a cradle at any time by scanning the pairing bar code on the cradle or by inserting it into the cradle with Pairing On Contacts enabled. The original scanner is disconnected from the cradle in favor of the new one (Point-to-Point mode only).

14

NOTE If three scanners are actively connected to the cradle

(Multipoint-to-Point mode), a fourth scanner cannot connect regardless of the pairing mode.

LS4278

UNLOCKED PAIRING MODE (Default)

LOCKED PAIRING MODE

Pairing Methods

There are two pairing methods. The default method pairs (connects) the scanner and cradle when the pairing bar code on the cradle is scanned. A second method pairs the scanner and cradle when the scanner is inserted in the cradle. To enable this feature, scan Enable Pair On Contacts below. With this feature enabled it is not necessary to scan the pairing bar code on the cradle. If the pairing is successful, a low/high connection beep sequence sounds a few seconds after the scanner is placed in the cradle.

ENABLE PAIR ON CONTACTS

DISABLE PAIR ON CONTACTS (Default)

Carriage Return/Line Feed

To append a carriage return/line feed to all transmitted data, scan the following bar codes in the order shown. To cancel this operation, the SET DEFAULTS bar

code on page 8 , or refer to the

Product Reference Guide .

SCAN OPTIONS

<DATA><SUFFIX>

ENTER

Quick Reference Guide 15

Ergonomic Recommendations

CAUTION In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local Health & Safety

Manager to ensure that you are adhering to your company’s safety programs to prevent employee injury.

• Reduce or eliminate repetitive motion

• Maintain a natural position

• Reduce or eliminate excessive force

• Keep objects that are used frequently within easy reach

• Perform tasks at correct heights

• Reduce or eliminate vibration

• Reduce or eliminate direct pressure

• Provide adjustable workstations

• Provide adequate clearance

• Provide a suitable working environment

• Improve work procedures.

Regulatory Information

This guide applies to Model Number LS4278.

All Zebra devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required.

Any changes or modifications to Zebra Technologies equipment, not expressly approved by

Zebra Technologies, could void the user's authority to operate the equipment.

Local language translations are available at the following website: http://www.zebra.com/support

Country Approval

Regulatory markings are applied to the device signifying the radio (s) are approved for use in the following countries: United States, Canada, Australia, Japan & Europe.

Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at http://www.zebra.com/doc.

Note: For 2.4GHz Products: Europe includes, Austria, Belgium, Bulgaria, Cyprus, Czech

Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,

Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,

Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and the United

Kingdom.

Radio Modules

The LS4278 Scanners contain an approved radio module. This module is the Bluetooth radio

Type: LMX5452.

16

Bluetooth Devices

This product is an approved Bluetooth device. BT ID: B02793.

Operation of the device without regulatory approval is illegal.

LS4278

FCC / EU RF Exposure Guidelines

Safety Information

The device complies with Internationally recognised standards covering Specific Absorption

Rate (SAR) related to human exposure to electromagnetic fields from radio devices.

Reducing RF Exposure – Use Properly

It is advisable to use the device only in the normal operating position.

Hand Held Devices:

To comply with FCC RF exposure requirements, this device must be operated in the hand.

Other operating configurations should be avoided.

Radio Frequency Interference Requirements

Radio Transmitters (Part 15)

Tested to comply with FCC Standards

FOR HOME OR OFFICE USE

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Radio Frequency Interference Requirements - Canada

Radio Transmitters

This device complies with RSS 210 of Industry & Science Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

Label Marking: The Term "IC:" before the radio certification only signifies that Industry Canada technical specifications were met.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil de la classe B est conforme à la norme NMB-003 du Canada.

Quick Reference Guide 17

Marking and European Economic Area (EEA)

Bluetooth for use through the EEA have the following restrictions:

• Maximum radiated transmit power of 10mW EIRP in the frequency range 2.400 -2.4835

GHz

• Belgium outside usage, the equipment is restricted to 2.460 -2.4835 GHz frequency range

Statement of Compliance

Zebra hereby, declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC and 2011/65/EU. A Declaration of Conformity may be obtained from http://www.zebra.com/doc

Laser Labels

In accordance with IEC60825-1 and EN60825, the following information is provided to the user:

ENGLISH

CLASS 1

CLASS 2

CLASS 1 LASER PRODUCT

LASER LIGHT

DO NOT STARE INTO BEAM

CLASS 2 LASER PRODUCT

DANISH / DANSK

KLASSE 1

KLASSE 2

KLASSE 1 LASERPRODUKT

LASERLYF

SE IKKE IND I STRÅLEN

KLASSE 2 LASERPRODUKT

DUTCH / NEDERLANDS

KLASSE 1 KLASSE-1 LASERPRODUKT

KLASSE 2 LASERLICHT

NIET IN STRAAL STAREN

KLASSE-2 LASERPRODUKT

FINNISH / SUOMI

LUOKKA 1 LUOKKA 1 LASERTUOTE

LUOKKA 2 LASERVALO

ÄLÄ TUIJOTA SÄDETTÄ

LUOKKA 2 LASERTUOTE

FRENCH / FRANÇAIS

CLASSE 1

CLASSE 2

PRODUIT LASER DE CLASSE 1

LUMIERE LASER

NE PAS REGARDER LE RAYON FIXEMENT

PRODUIT LASER DE CLASSE 2

GERMAN / DEUTSCH

KLASSE 1

KLASSE 2

LASERPRODUKT DER KLASSE 1

LASERSTRAHLEN

NICHT DIREKT IN DEN LASERSTRAHL SCHAUEN

LASERPRODUKT DER KLASSE 2

HEBREW

ITALIAN / ITALIANO

CLASSE 1 PRODOTTO AL LASER DI CLASSE 1

CLASSE 2 LUCE LASER

NON FISSARE IL RAGGIO

PRODOTTO AL LASER DI CLASSE 2

NORWEGIAN / NORSK

KLASSE 1 LASERPRODUKT, KLASSE 1

KLASSE 2 LASERLYS

IKKE STIRR INN I LYSSTRÅLEN

LASERPRODUKT, KLASSE 2

PORTUGUESE / PORTUGUÊS

CLASSE 1 PRODUTO LASER DA CLASSE 1

CLASSE 2 LUZ DE LASER

NÃO FIXAR O RAIO LUMINOSO

PRODUTO LASER DA CLASSE 2

SPANISH / ESPAÑOL

CLASE 1

CLASE 2

PRODUCTO LÁSER DE LA CLASE 1

LUZ LÁSER

NO MIRE FIJAMENTE EL HAZ

PRODUCTO LÁSER DE LA CLASE 2

SWEDISH / SVENSKA

KLASS 1

KLASS 2

LASERPRODUKT KLASS 1

LASERLJUS

STIRRA INTE MOT STRÅLEN

LASERPRODUKT KLASS 2

18 LS4278

Laser Devices

COMPLIES WITH 21CFR1040.10 AND 1040.11 EXCEPT FOR DEVIATIONS

PURSUANT TO LASER NOTICE NO. 50, DATED JUNE 24, 2007 AND IEC

60825-1 (Ed. 2.0), EN60825-1:2007.

The laser classification is marked on one of the labels on the device.

Class 1 Laser devices are not considered to be hazardous when used for their intended purpose. The following statement is required to comply with US and international regulations:

Caution: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure.

Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful.

Scanner Labeling

Waste Electrical and Electronic Equipment (WEEE)

English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how to return product, please go to: http://www.zebra.com/weee.

Български : За клиенти от ЕС : След края на полезния им живот всички продукти трябва да се връщат на Zebra за рециклиране . За информация относно връщането на продукти , моля отидете на адрес : http://www.zebra.com/weee.

Č eština: Pro zákazníky z EU: Všechny produkty je nutné po skon č ení jejich životnosti vrátit spole č nosti

Zebra k recyklaci. Informace o zp ů sobu vrácení produktu najdete na webové stránce: http://www.zebra.com/weee.

Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er udtjent. Læs oplysningerne om returnering af produkter på: http://www.zebra.com/weee.

Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer zum Recycling an Zebra zurückgesandt werden. Informationen zur Rücksendung von Produkten finden Sie unter http://www.zebra.com/weee.

Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgil Zebra'ile.

Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun aadressi: http://www.zebra.com/weee.

Quick Reference Guide 19

Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Zebra al final de su ciclo de vida para que sean reciclados. Si desea más información sobre cómo devolver un producto, visite: http://www.zebra.com/weee.

Ελληνικά : Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει να επιστρ έφονται στην Zebra για ανακύκλωση. Για περισσότερες πληροφορίες σχετικά με την επιστροφή ενός π

ροϊόντος, επισκεφθείτε τη διεύθυνση http://www.zebra.com/weee στο Διαδίκτυο.

Français : Clients de l'Union Européenne : Tous les produits en fin de cycle de vie doivent être retournés à

Zebra pour recyclage. Pour de plus amples informations sur le retour de produits, consultez : http://www.zebra.com/weee.

Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito Web: http://www.zebra.com/weee.

Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip grąžinti gaminį, rasite: http://www.zebra.com/weee.

Latviešu: ES klientiem: visi produkti p ē c to kalpošanas m ū ža beig ā m ir j ā nog ā d ā atpaka ļ Zebra otrreiz ē jai p ā rstr ā dei. Lai ieg ū tu inform ā ciju par produktu nog ā d ā šanu Zebra, l ū dzu, skatiet: http://www.zebra.com/weee.

Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz kell eljuttatni

újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a http://www.zebra.com/weee weboldalra.

Malti: G ħ al klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-a ħħ ar talħ ajja ta' l-u ż u tag ħ hom, iridu ji ġ u rritornati g ħ and Zebra g ħ ar-ri ċ ikla ġġ . G ħ al aktar tag ħ rif dwar kif g ħ andek tirritorna l-prodott, jekk jog ħġ bok ż ur: http://www.zebra.com/weee.

Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg http://www.zebra.com/weee voor meer informatie over het terugzenden van producten.

Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji nale ź y zwróci ć do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu produktów znajduj ą si ę na stronie internetowej http://www.zebra.com/weee.

Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Zebra para reciclagem. Para obter informações sobre como devolver o produto, visite: http://www.zebra.com/weee.

Românesc: Pentru clien ţ ii din UE: Toate produsele, la sfâr ş itul duratei lor de func ţ ionare, trebuie returnate la

Zebra pentru reciclare. Pentru informa ţ ii despre returnarea produsului, accesa ţ i: http://www.zebra.com/weee.

Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Zebra za reciklažo.

Za informacije o vraèilu izdelka obišèite: http://www.zebra.com/weee.

Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on osoitteessa http://www.zebra.com/weee.

Svenska

:

För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Zebra för

återvinning. Information om hur du returnerar produkten finns på http://www.zebra.com/weee.

Türkçe: AB Mü ş terileri için: Kullan ı m süresi dolan tüm ürünler geri dönü ş türme için Zebra'ya iade edilmelidir.

Ürünlerin nas ı l iade edilece ğ i hakk ı nda bilgi için lütfen ş u adresi ziyaret edin: http://www.zebra.com/weee.

TURKISH WEEE Statement of Compliance

EEE Yönetmeli ğ ine Uygundur

Service Information

If you have a problem using the equipment, contact your facility’s technical or systems support. If there is a problem with the equipment, they will contact the

Zebra Global Customer Support Center at: http://www.zebra.com/support.

For the latest version of this guide go to: http://www.zebra.com/support.

Zebra Technologies Corporation

Lincolnshire, IL U.S.A.

http://www.zebra.com

Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra Technologies company.

© 2015 Symbol Technologies, Inc.

72-69835-02 Revision A - March 2015