Installation
1. Power off the ET1.
2. Remove the battery.
3. If the handstrap is installed, rotate the handstrap to access the expansion module screws.
4. Remove two screws using a T8
Torx ® screwdriver.
5. Remove the existing module. Do not remove filler plate.
7. Secure the two screws using a
T8 Torx screwdriver.
8. Replace the battery.
6. Install the new module.
Filler Plate
Data Capture
MSR Swipe
Additional Information
For detailed information on setting up and using the
Scanning and Scanning/MSR module, refer to the
ET1 Enterprise Tablet User Guide and Integrator
Guide .
Regulatory Information
This guide applies to the following model numbers:
SCANMOD-ET1 and MSRSCAN-ET1.
All Zebra devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required.
Local language translations are available at the following website: http://www.zebra.com/support.
Any changes or modifications to Zebra equipment, not expressly approved by Zebra could void the user’s authority to operate the equipment.
For use only with Zebra approved and UL Listed mobile computers. Zebra approved and UL Listed accessories and/or Zebra approved and UL Listed/
Recognized battery packs.
Declared maximum operating temperature: 50 °C.
Health and Safety
Recommendations
Ergonomic Recommendations
CAUTION In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below.
Consult with your local Health &
Safety Manager to ensure that you are adhering to your company’s safety programs to prevent employee injury.
• Reduce or eliminate repetitive motion
• Maintain a neutral postures
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures
Laser Devices
Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful.
CAUTION: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure.
Labeling
1
2
3
CAUTION- CLASS 2 LASER LIGHT WHEN OPEN. DO NOT
STARE INTO THE BEAM. ATTENTION- LUMIÉRE LASER DE
CLASSE 2 EN CAS D'OUVERTURE. NE PAS REGARDER
DANS LE FAISCEAU.VORSICHT- LASERLICHT KLASSE 2,
WENN ABDECKUNG GEÖFFNET. NICHT IN DEN STRAHL
BLICKEN. ⊼ᛣ˖ᠧᓔᯊঞ㘨䫕༅ᬜᯊ᳝▔ܝ䕤ᇘ࣓Ⳉ㾚ܝᴳ
COMPLIES WITH 21CFR1040.10 AND 1040.11 EXCEPT FOR
DEVIATIONS PURSUANT TO LASER NOTICE NO. 50, DATED
JUNE 24, 2007 AND IEC 60825-1 (Ed.2.0),EN60825-1:2007 &
IEC62471:2006 (Ed. 1.0) EN62471:2008.
LASER LIGHT- DO NOT STARE INTO BEAM.
CLASS 2 LASER PRODUCT. LASERLICHT - NICHT
IN DEN STRAHL BLICKEN. LASER KLASSE 2.
LUMIÈRE LASER - NE PAS REGARDER DANS
LE FAISCEAU. APPAREIL À LASER DE
CLASSE 2 630-680nm, 1mW
▔ܝ䕤ᇘ࣓Ⳉ㾚ܝᴳ㉏▔ܝѻક
Label read:
1. CAUTION - CLASS 2 LASER LIGHT WHEN
OPEN. DO NOT STARE INTO BEAM.
2. COMPLIES WITH 21CFR1040.10 & 1040.11
EXCEPT FOR DEVIATIONS PURSUANT TO
LASER NOTICE NO. 50, DATED JUNE 24, 2007
AND IEC/EN 60825-1:2007 AND/OR IEC/EN
60825-1:2014.
3. LASER LIGHT - DO NOT STARE INTO BEAM.
CLASS 2 LASER PRODUCT.
Radio Frequency Interference
Requirements-FCC
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Zebra reserves the right to make changes to any product to improve reliability, function, or design.
Zebra does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Zebra products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Zebra products.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Zebra and the stylized Zebra head are trademarks of
ZIH Corp., registered in many jurisdictions worldwide.
All other trademarks are the property of their respective owners.
©2016 Symbol Technologies LLC, a subsidiary of
Zebra Technologies Corporation. All rights reserved.
Radio Frequency Interference
Requirements – Canada
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est conforme
à la norme NMB-003 du Canada.
Marking and European
Economic Area (EEA)
Statement of Compliance
Zebra hereby declares that this device is in compliance with all applicable Directives, 2014/30/
EU, 2014/35/EU and 2011/65/EU. The full text of the
EU Declaration of Conformity is available at the following internet address: http://www.zebra.com/doc.
Japan (VCCI) - Voluntary Control
Council for Interference
Class B ITE
この装置は、情報処理装置等電波障害自主規制協議
会 （ＶＣＣＩ）の基準に基づくクラス B 情報技術
装置です。この装置は、家庭環境で使用することを
目的としていますが、この装置がラジオやテレビジ
ョン受信機に近接して使用されると、受信障害を引
き起こすことがあります。 取扱説明書に従って正
しい取り扱いをして下さい。
72-162929-03 Rev. A — August 2016
Korea Warning Statement for Class B ITE
기 종별
B 급 기기
( 가정용
방송통신기기
)
사 용 자 안 내 문
이 기기는 가정용 (B 급 ) 으로
전자파적합등록을
한 기기로서 주로 가정에서
사용하는 것을 목적
으로 하며, 모든 지역에서 사용할 수
있습니다 .
Waste Electrical and
Electronic Equipment (WEEE)
English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling.
For information on how to return product, please go to: http://www.zebra.com/weee.
Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie doivent être retournés
à Zebra pour recyclage. Pour de plus amples informations sur le retour de produits, consultez : http://www.zebra.com/weee.
Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Zebra al final de su ciclo de vida para que sean reciclados. Si desea más información sobre cómo devolver un producto, visite: http://www.zebra.com/weee.
Bulgarish: За клиенти от ЕС : След края на полезния им живот всички продукти трябва да се връщат на Zebra за рециклиране . За информация относно връщането на продукти , моля отидете на адрес : http://www.zebra.com/weee.
Deutsch: Für Kunden innerhalb der EU: Alle
Produkte müssen am Ende ihrer Lebensdauer zum
Recycling an Zebra zurückgesandt werden.
Informationen zur Rücksendung von Produkten finden Sie unter http://www.zebra.com/weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito Web: http://www.zebra.com/weee.
Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Zebra para reciclagem. Para obter informações sobre como devolver o produto, visite: http://www.zebra.com/weee.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg http://www.zebra.com/weee voor meer informatie over het terugzenden van producten.
Polski:
Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji nale¿y zwróciæ do firmy
Zebra w celu ich utylizacji. Informacje na temat zwrotu produktów znajduj¹ siê na stronie internetowej http://www.zebra.com/weee
.
Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich životnosti vrátit spoleènosti
Zebra k recyklaci. Informace o zpùsobu vrácení produktu najdete na webové stránce: http://www.zebra.com/weee.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgil
Zebra'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun aadressi: http://www.zebra.com/weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz kell eljuttatni
újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a http://www.zebra.com/weee weboldalra.
Slovenski:
Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Zebra za reciklažo. Za informacije o vraèilu izdelka obišèite: http://www.zebra.com/weee.
Svenska:
För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Zebra för
återvinning. Information om hur du returnerar produkten finns på http://www.zebra.com/weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi Zebrayhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on osoitteessa http://www.zebra.com/weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er udtjent. Læs oplysningerne om returnering af produkter på: http://www.zebra.com/weee.
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα,
στο τέλος της διάρκειας ζωής τους, πρέπει να
επιστρέφονται στην Zebra για ανακύκλωση. Για
περισσότερες πληροφορίες σχετικά με την επιστροφή
ενός προϊόντος, επισκεφθείτε τη διεύθυνση http://www.zebra.com/weee στο Διαδίκτυο.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom, iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif għandek tirritorna l-prodott, jekk jogħġbok żur: http://www.zebra.com/weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby ich životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie informácie o vrátení výrobkov nájdete na: http://www.zebra.com/weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip grąžinti gaminį, rasite: http://www.zebra.com/weee.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ Zebra otrreizējai pārstrādei. Lai iegūtu informāciju par produktu nogādāšanu Zebra, lūdzu, skatiet: http://www.zebra.com/weee.
Warranty
For the complete Zebra hardware product warranty statement, go to: http://www.zebra.com/warranty.
Service Information
If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there is a problem with the equipment, they will contact the
Zebra Global Support at: http://www.zebra.com/support.
For the latest version of this guide go to: http://www.zebra.com/support.
CMM Disclosure
ᴿᇩ⢟䍞
(Parts)
(Metal Parts)
(Circuit Modules)
(Cables and Cable
Assemblies)
(Pb) (Hg) (Cd) (Cr (VI))
O O O O
(PBB)
O
X
O
O
O
O
O
O
O
O
O
(PBDE)
O
O
O
(Plastic and Polymeric
Parts)
O O O O O O
(Optics and Optical
Components)
X O X O O O
(Batteries)
O O O O O O ᵢ㺞Ṳדᦤ6-7Ⲻ㿺ᇐ㕌Ⱦ
2 㺞⽰䈛ᴿᇩ⢟䍞൞䈛䜞Ԭᡶᴿൽ䍞ᶆᯏѣⲺ䠅ൽ൞*%7㿺ᇐⲺ䲆䠅
㾷≸ԛсȾ
; 㺞⽰䈛ᴿᇩ⢟䍞㠩ቇ൞䈛䜞ԬⲺḆжൽ䍞ᶆᯏѣⲺ䠅䎻࠰*%7㿺ᇐ
Ⲻ䲆䠅㾷≸ȾԷѐਥ൞↚༺θṯᦤᇔ䱻߫ሯр㺞ѣᢉćhĈⲺᢶᵥഖ䘑
㺂䘑ж↛䈪᱄Ⱦε
This table was created to comply with China RoHS requirements.
SCANMOD-ET1
MSRSCAN-ET1
QUICK REFERENCE
GUIDE
