WA9902 - RFID MODULE UHF LINEAR (CE) ENDCAP
H/W INSTALLATION SHEET
Important: All Approval and safety information is outlined in the ‘WORKABOUTPRO4 Regulatory &
Warranty Guide – part number 8000296 provided with each WORKABOUTPRO4.
Warning
:
The WORKABOUTPRO4 with the RFID option must not be held closer than 20 cm from the rest of the body.
This product must not be used in a holster or on a belt-clip.
© 2015 Symbol Technologies, Inc.
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of
Symbol Technologies, Inc., a Zebra Technologies company.
Feb 27, 2015
8000328-001 A
1. Product Description
Easily installable expansion modules for the WORKABOUT PRO4 allow you to customise this hand-held to meet your specific mobile computing requirements. This chapter outlines how to install the European
UHF Linear RFID Module.
The RFID MODULE UHF LINEAR (WA9902) kit is based on the Sailfish UHF module from
Zebra (Model: 21-121560). It is made of 4 parts:
•
ASSY MODULE UHF WAP4 EUROPEAN
•
ASSY ANTENNA LINEAR EUROPEAN WAP4
•
INSTRUCTION SHEET WAP4 UHF LINEAR EUROPEAN
•
LABELS CE WAP4 UHF LINEAR VARIANT
Figure 1-1 ASSY MODULE UHF WAP4 EUROPEAN Figure 1-2 ASSY ANTENNA LINEAR
EUROPEAN WAP4
Figure 1-4 LABELS CE WAP4 UHF LINEAR
VARIANT
Figure 1-3 INSTRUCTION SHEET WAP4 UHF LINEAR EUROPEAN
© 2015 Symbol Technologies, Inc.
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of
Symbol Technologies, Inc., a Zebra Technologies company.
Feb 27, 2015
8000328-001 A
2. Product Installation
Before installing a module in the WORKABOUT PRO4, all power sources must be turned off.
•
Remove the battery. If your unit is using AC power, disconnect it.
Figure 2-1
Battery location
With the power shut down, you can now install the European RFID Module.
•
Remove the existing endcap and pod or backplate
Figure 2-2 WAP4 Disassembled
© 2015 Symbol Technologies, Inc.
Feb 27, 2015
8000328-001 A
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of
Symbol Technologies, Inc., a Zebra Technologies company.
Optional : If the RFID module is intend to be installed in 7528XPUHFE (WAP4 including WWAN) , stick the EMI gasket as shown on the picture below:
EMI Gasket
Aligning edge
•
Slide the RFID Module inside the back opening
Figure 2-3 RFID Module Assembly
© 2015 Symbol Technologies, Inc.
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of
Symbol Technologies, Inc., a Zebra Technologies company.
Feb 27, 2015
8000328-001 A
•
Drive (2Kgf.cm / 1.7 lbs.In) the 4 screws that fix the RFID module on WAP4 frame
Figure 2-4 RFID Module Assembly
Place the antenna in the right slot:
•
For WAP4 with WLAN only (7528XUHFE), antenna must be placed in the bottom slot
Figure 2-5 Antenna position for WLAN only WAP4 version
•
For WAP4 with WWAN (7528XPUHFE), antenna must be placed in the middle slot
Figure 2-6 Antenna position for WWAN WAP4 version
© 2015 Symbol Technologies, Inc.
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of
Symbol Technologies, Inc., a Zebra Technologies company.
Feb 27, 2015
8000328-001 A
Antenna should be correctly inserted in the rubber
Figure 2-7 Right insertion (antenna is pushed totally in the rubber)
Figure 2-8 Wrong insertion (antenna comes out of the rubber)
•
Drive (2Kgf.cm / 1.7 lbs-In) the 2 self-tapping screws to fix the antenna stopper
*
Figure 2-9 Antenna stopper assembly
© 2015 Symbol Technologies, Inc.
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of
Symbol Technologies, Inc., a Zebra Technologies company.
Feb 27, 2015
8000328-001 A
•
Plug the U.FL antenna connector to the Sailfish module.
Warning: Make sure you use the proper RF port (right side of the Sailfish)
Figure 2-10 Linear antenna assembly
•
Reassemble the pod or backplate and the endcap (3 Kgf.cm / 2.6 lbs.In)
Figure 2-11 Final Assembly
© 2015 Symbol Technologies, Inc.
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of
Symbol Technologies, Inc., a Zebra Technologies company.
Feb 27, 2015
8000328-001 A
•
IF the model number of WorkAbout Pro4 is 7528XUHFE (WLAN only) put this label:
Figure 2-12 CE Label for WAP4 WLAN only variant
•
IF the model number of WorkAbout Pro4 is 7528XPUHFE (WWAN version) put this label type:
Figure 2-13 CE Label for WAP4 WWAN variant
Stick the label in the location following depending on WorkAbout Pro4 variant:
Figure 2-9 WorkAbout Pro4 Long Alphanumeric Keyboard Figure 2-10 WorkAbout Pro4 Short Numeric Keyboard
© 2015 Symbol Technologies, Inc.
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of
Symbol Technologies, Inc., a Zebra Technologies company.
Feb 27, 2015
8000328-001 A
3. Software installation:
To get current driver for WorkAbout Pro4, go to the website address below: http://community.psion.com/downloads/developer_sdkhdk/m/rfid_sdk/
•
Copy and install the latest CAB file named “WAP4_WM_RFID_UHF”.
Figure 3-1 Driver CAB file Figure 3-2 Driver installation
•
After installation, select RFID Demo in the Start menu to start the RFID sample application.
Figure 3-3 RFID demo Icon Figure 3-4 RFID Sample Application Window
© 2015 Symbol Technologies, Inc.
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of
Symbol Technologies, Inc., a Zebra Technologies company.
Feb 27, 2015
8000328-001 A
•
To read the TAG ID, press the Start Reading button. Put the TAG in front of the antenna. Tap Stop
Reading to stop the inventory.
Figure 3-5 ID Tag Reading
For detailed instructions on how to use the RFID demo application, please visit http://www.zebra.com
and download ‘ RFID Demo Applications User Guide (P/N 72E-160038-01) ’
4. Reading area:
This area depends on the TAG type, TAG packaging, Tag position and environment (metallic or not).
Reading Area
Tag
Figure 4-1 Reading area
© 2015 Symbol Technologies, Inc.
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of
Symbol Technologies, Inc., a Zebra Technologies company.
Feb 27, 2015
8000328-001 A
RFID MODULE UHF LINEAR (CE) ENDCAP
RFID Regulatory information
CE Marking:
Please CE marking and details of other country markings refer to the Declaration of
Conformity (Doc) at
http://www.zebra.com
© 2015 Symbol Technologies, Inc.
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of
Symbol Technologies, Inc., a Zebra Technologies company.
Feb 27, 2015
8000328-001 A
