RS409 Ring Scanner
Quick Reference Guide
2 RS409 Ring Scanner
©2016 Symbol Technologies LLC, a subsidiary of Zebra Technologies
Corporation. All rights reserved.
Zebra reserves the right to make changes to any product to improve reliability, function, or design.
Zebra does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system,
apparatus, machine, material, method, or process in which Zebra products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Zebra products.
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The
Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra
Technologies company. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Warranty
For the complete Zebra hardware product warranty statement, go to: http://www.zebra.com/warranty .
Quick Reference Guide
Introduction
The RS409 ring scanner is a modular, wearable laser scanner that allows the operator hands-free bar code scanning capability. The scanner is used with the
WT4070/90 wearable terminal.
The RS409 is worn on the operator’s index finger, and utilizes a thumb-operated trigger. The RS409 connects via an interface cable to the wearable terminal, which provides power and performs the data collection functions. The RS409 is available in two configurations; a short cable version for connection to a wrist mounted wearable terminal, and a long cable version for connection to a hip mounted wearable terminal.
Connector
3
Exit Window Scan Assembly Scan LED
Finger Strap
Assembly
Scan Trigger
Trigger
Assembly
4 RS409 Ring Scanner
Changing Trigger Position
The trigger assembly of the RS409 rotates to provide left-hand or right-hand use.
1.
Determine whether the RS409 is used on the right or left hand.
CAUTION The trigger assembly only rotates 180° around the back of the scan assembly. Do not rotate the trigger assembly past the designed stops.
2.
Rotate the trigger assembly so that the scan trigger is positioned next to the thumb when the RS409 is placed on the index finger.
Quick Reference Guide
Installation
The RS409 connects to the wearable terminal and mounts on the index finger.
1.
On the wearable terminal, remove the connector cap.
2.
Connect the RS409 interface cable to the wearable terminal interface connector. If connecting to a wrist mounted wearable terminal, connect to the interface connector closest to the wrist.
5
Scanner Cable Connector Interface Connector
3.
Slide the RS409 onto the index finger with the scan trigger next to the thumb.
4.
Tighten the finger strap.
6 RS409 Ring Scanner
5.
If required, cut excess finger strap material.
6.
Warm boot the wearable terminal.
Using the Scanner
To scan bar codes:
1.
Turn on the wearable terminal.
2.
Launch a scanning application.
3.
Press the scan trigger and aim the RS409 at a bar code.
The scan LED lights red to indicate the RS409 is on.
4.
Adjust the aim so that the thin, red laser beam covers the entire length of the bar code.
Right
012345
Wrong
012345
Quick Reference Guide
5.
If the decode is successful the LED turns green. The terminal beeps if programed accordingly.
Scanning Tips
• For larger bar codes, hold the RS409 farther away from the bar code.
• For bar codes with bars that are closer together, hold the RS409 closer to the bar code.
• The optimal scanning distance varies with bar code density, but 10 to 25 cm (4 to 10 inches) generally works. Practice to determine what distances to work within.
• Do not position the RS409 exactly perpendicular to the bar code being scanned. In this position, reflected light can bounce back into the exit window, and possibly prevent a successful decode.
Finger Strap Assembly Replacement
The finger strap assembly can be changed for each user or for replacement. To replace the finger strap assembly:
1.
Press down on the finger strap assembly release tab.
7
Release Tab
2.
Slide the finger strap assembly out of the trigger assembly.
3.
Align a new finger strap assembly with the slot in the trigger assembly.
4.
Push the finger strap assembly into the trigger assembly until the release tab clicks into place.
8 RS409 Ring Scanner
5.
Insert your index finger through the finger strap. Tighten the strap and press the hook and pile together.
6.
If required, cut excess finger strap material.
Replacing the Trigger Assembly
To replace the trigger assembly:
1.
Remove the finger strap assembly.
2.
Turn the RS409 upside-down.
3.
Remove the set screw with screwdriver.
4.
Turn the trigger assembly counter-clockwise until the exit window and scan trigger align.
5.
Lift the trigger assembly off the scan assembly.
6.
Align replacement trigger assembly with scan assembly.
7.
Rotate trigger assembly 1/4 turn clockwise.
8.
Tighten the set screw with screwdriver.
9.
Replace finger strap assembly.
Quick Reference Guide
Cleaning
Wipe the exit window periodically with a lens tissue or other material suitable for cleaning optical material such as eyeglasses.
CAUTION Do not pour, spray, or spill any liquid on the RS409.
9
Troubleshooting
Symptom
Laser beam does not display when pressing the trigger.
RS409 does not decode a bar code.
Probable Cause Action
Interface cable is not secure.
Power is not applied to
RS409.
Verify that the interface cable connection is connected properly.
Power for the RS409 is provided by the wearable terminal. Verify that the wearable terminal has a charged battery installed.
Launch scanning application on the wearable terminal.
Scan enabled application on the wearable terminal is not running.
Bar code is unreadable. Verify that the bar code is not defective, i.e., smudged or broken.
Exit window is dirty.
Clean exit window with a lens tissue. Tissues for eyeglasses work well. Do not use tissues coated with lotion.
Symbology is not enabled.
See your system administrator.
10 RS409 Ring Scanner
Ergonomic Recommendations
CAUTION In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local
Health & Safety Manager to ensure that you are adhering to your company’s safety programs to prevent employee injury.
• Reduce or eliminate repetitive motion
• Maintain a natural position
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures.
Regulatory Information
This guide applies to model number: RS409.
All Zebra devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required.
Regulatory Information is available in French, Italian, German, Spanish (Spain),
Portuguese, Japanese, Korean, Russian and Simplified Chinese. Please see the following website: http://www.zebra.com/support and look for your specific product.
Any changes or modifications to Zebra equipment, not expressly approved by
Zebra, could void the user's authority to operate the equipment.
CAUTION Only use Zebra approved and UL Listed terminals.
Quick Reference Guide 11
Laser Devices
Complies with 21CFR1040.10 & 1040.11 except for deviations pursuant to Laser
Notice NO. 50, dated June 24, 2007 and IEC/EN 60825-1:2007 and/or IEC/EN
60825-1:2014.
The laser classification is marked on one of the labels on the device.
Class 1 Laser devices are not considered to be hazardous when used for their intended purpose. The following statement is required to comply with US and international regulations:
Caution: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure.
Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful.
12 RS409 Ring Scanner
Radio Frequency Interference Requirements-FCC
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements - Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Marking and European Economic Area (EEA)
Statement of Compliance
Zebra hereby declares that this radio equipment is in compliance with Directive
2011/65/EU and 1999/5/EC or 2014/53/EU (2014/53/EU supersedes 1999/5/EC from 13th June 2017). The full text of the EU Declaration of Conformity is available at the following internet address: http://www.zebra.com/doc.
Quick Reference Guide 13
Waste Electrical and Electronic Equipment
(WEEE)
English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how to return product, please go to: http://www.zebra.com/weee.
Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie doivent
être retournés à Zebra pour recyclage. Pour de plus amples informations sur le retour de produits, consultez : http://www.zebra.com/weee.
Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a
Zebra al final de su ciclo de vida para que sean reciclados. Si desea más información sobre cómo devolver un producto, visite: http://www.zebra.com/weee.
Bulgarish: За клиенти от ЕС : След края на полезния им живот всички продукти трябва да се връщат на Zebra за рециклиране . За информация относно връщането на продукти , моля отидете на адрес : http://www.zebra.com/weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer
Lebensdauer zum Recycling an Zebra zurückgesandt werden. Informationen zur
Rücksendung von Produkten finden Sie unter http://www.zebra.com/weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito Web: http://www.zebra.com/weee.
Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à
Zebra para reciclagem. Para obter informações sobre como devolver o produto, visite: http://www.zebra.com/weee.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg http://www.zebra.com/weee voor meer informatie over het terugzenden van producten.
Polski:
Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji nale¿y zwróciæ do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu produktów znajduj¹ siê na stronie internetowej http://www.zebra.com/weee .
Č eština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich životnosti vrátit spoleènosti Zebra k recyklaci. Informace o zpùsobu vrácení produktu najdete na webové stránce: http://www.zebra.com/weee.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun aadressi: http://www.zebra.com/weee.
14 RS409 Ring Scanner
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz kell eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a http://www.zebra.com/weee weboldalra.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju
Zebra za reciklažo. Za informacije o vraèilu izdelka obišèite: http://www.zebra.com/weee.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till
Zebra för återvinning. Information om hur du returnerar produkten finns på http://www.zebra.com/weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on osoitteessa http://www.zebra.com/weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er udtjent. Læs oplysningerne om returnering af produkter på: http://www.zebra.com/weee.
Ελληνικά : Για πελάτες στην Ε .
Ε .: Όλα τα προϊόντα , στο τέλος της διάρκειας ζωής τους ,
πρέπει να επιστρέφονται στην Zebra για ανακύκλωση . Για περισσότερες πληροφορίες
σχετικά με την επιστροφή ενός προϊόντος , επισκεφθείτε τη διεύθυνση http://www.zebra.com/weee στο Διαδίκτυο .
Malti: G ħ al klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-a ħħ ar talħ ajja ta' l-u ż u tag ħ hom, iridu ji ġ u rritornati g ħ and Zebra g ħ ar-ri ċ ikla ġġ . G ħ al aktar tag ħ rif dwar kif g ħ andek tirritorna l-prodott, jekk jog ħġ bok ż ur: http://www.zebra.com/weee.
Românesc: Pentru clien ţ ii din UE: Toate produsele, la sfâr ş itul duratei lor de func ţ ionare, trebuie returnate la Zebra pentru reciclare. Pentru informa ţ ii despre returnarea produsului, accesa ţ i: http://www.zebra.com/weee.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju
Zebra za reciklažo. Za informacije o vra č ilu izdelka obiš č ite: http://www.zebra.com/weee.
Sloven č ina: Pre zákazníkov z krajín EU: Všetky výrobky musia by ť po uplynutí doby ich životnosti vrátené spolo č nosti Zebra na recykláciu. Bližšie informácie o vrátení výrobkov nájdete na: http://www.zebra.com/weee.
Lietuvi ų : ES vartotojams: visi gaminiai, pasibaigus j ų eksploatacijos laikui, turi b ū ti gr ą žinti utilizuoti į kompanij ą „Zebra“. Daugiau informacijos, kaip gr ą žinti gamin į , rasite: http://www.zebra.com/weee.
Latviešu: ES klientiem: visi produkti p ē c to kalpošanas m ū ža beig ā m ir j ā nog ā d ā atpaka ļ
Zebra otrreiz ē jai p ā rstr ā dei. Lai ieg ū tu inform ā ciju par produktu nog ā d ā šanu Zebra, l ū dzu, skatiet: http://www.zebra.com/weee.
Türkçe: AB Mü ş terileri için: Kullan ı m süresi dolan tüm ürünler geri dönü ş türme için
Zebra'ya iade edilmelidir. Ürünlerin nas ı l iade edilece ğ i hakk ı nda bilgi için lütfen ş u adresi ziyaret edin: http://www.zebra.com/weee.
Quick Reference Guide 15
Service Information
If you have a problem using the equipment, contact your facility’s Technical or
Systems Support. If there is a problem with the equipment, they will contact the
Zebra Support at: http://www.zebra.com/support .
For the latest version of this guide go to: http://www.zebra.com/support .
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Zebra and the stylized Zebra head are trademarks of ZIH Corp., registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners.
©2016 Symbol Technologies LLC, a subsidiary of Zebra Technologies Corporation. All rights reserved..
72-86010-04 Revision A - July 2016
