www.securitytronix.com

19-inch LCD Display Unit

ST-HDLED18.5

User Manual

Thank you for purchasing our product.

If there is any question or request, please do not hesitate to contact us.

This manual may contain technical or printing errors, and the content is subject to change without notice.

The updates will be added into the new version of this manual.

For further assistance please contact technical support at 1-800-688-9282, press 3 then 2.

1

Regulatory Information

2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the

European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the

European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.

II

19-inch LCD Display Unit User’s Manual

This manual, as well as the software described in it, is furnished under license and may be used or copied only in accordance with the terms of such license. The content of this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment.

Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission.

III

Chapter1.

Introduction

1.1

Key Features

 Supports 1366 x 768 resolution

 User-friendly operation menu

 Three image modes to adapt to different environments

 1 channel HDMI 1.3 input interface ）

 Supports software spread-spectrum technology to reduce EMI radiation

 Standby Power Consumption is lower than 0.5W

 Viewing Angle:Horizontal 90°, Vertical 65º

1.2

Power Supply Connection

Insert the 3-pin power plug into a properly grounded socket and turn the rocker switch on.

Figure 1.1 Power Input







Power input specification from 100VAC to 240VAC or provide automatic switching between high line and low line input ranges.

Turn off the main power switch of the display unit, and pull the plug from the power outlet if the display unit will not be used for a long time.

Never connect the device to DC power.

1

Chapter2.

Device Interfaces

Inte rfaces

POWER IN

HDMI IN

VGA IN

Figure 2.1 Rear Panel of Device

De scription

Power Input

HDMI Digital Signal Input

VGA Analog Signal Input

2

Chapter3.

Panel Keys

Keys on the lower right corner of the display unit panel are shown in Figure 3.1

Figure 3.1 Keys on the Display Unit

The functions of the keys on lower right corner of the display unit vary according to different situations. The functions are shown in the flow chart below:

3

Chapter4.

Basic Operation

4.1

Contrast

Turn on the display unit when the power supply is on and input source is confirmed.

Press ◄ key of the remote controller to enter the menu as shown on the right. press ◄ or ► to adjust the value of contrast.

Press

MENU to accomplish the contrast adjustment.

Figure 4.1 Input Source

4.2

Brightness

Turn on the display unit when the power supply is on and input source is confirmed.

Press ► key of the remote controller to enter the menu as shown on the right. press ◄ or ► to adjust the value of brightness.

brightness

Press

adjustment.

MENU to accomplish the

4.3

Auto Adjust

Turn on the display unit when the power supply is on and input source is confirmed.

Press

AUTO

key of the remote controller to enter the menu as shown on the right(In VGA Signal).

Figure 4.2 Input Source

Figure 4.3 Input Source

4

4.4

Main Menu

4.4.1 Image Settings

Purpose:

You can adjust the picture parameters by switching image modes and adjust the values of contrast, brightness, color temperature, auto adjust, color adjust.

Steps:

1.

Press

Menu

key to enter the main menu interface as shown below.

2.

Press

MENU

key to enter the setting you want.

3.

Press ◄ or ► to adjust the value. It applies for adjusting contrast, brightness, color temp and other parameters.







Contrast, Brightness: Press ◄ or ► to set the contrast. The range varies from 0-100.

Color temperature : Press ◄ or ► to set the color temperature you need.

Gray indicates that under current mode or current input source condition it is not adjustable;

Yellow indicates that it is adjustable.

4.

Press

AUTO

key to return to the main menu after accomplishing the adjustment.

Figure 4.4.1 Image Settings

5

4.4.2 Image Adjustment

Purpose:

When the input source is selected VGA, you can adjust the VGA parameters. It is for adjusting

VGA H position, V Position, clock and phase.

Steps:

1.

Press

Menu

key to enter the main menu interface.

2.

Press ◄ key to enter the VGA parameter setting interface. (You can select

Auto Adjust

and press ◄ or ► to adjust the VGA parameters automatically or adjust it manually)

3.

Select

H Position

and press ◄ or ► to adjust the

H Position

4.

Select

V Position

and press ◄ or ► to adjust the

V position

.

5.

Select

Clock

and press ◄ or ► to adjust the clock

.

6.

Select

Phase

and press ◄ or ► to adjust the phase

.

The range of the adjustment varies between 0-100.

7.

Press

Menu

key to return to the main menu after accomplishing the adjustment.

Figure 4.4.2 Image Adjustment

6

4.4.3 OSD Setting

Purpose:

You can set the language, blending and OSD duration of the menu.

Steps:

1.

Press

MENU key to enter the main menu interface.

2.

Press ◄ key twice and press

MENU

key to enter the 【 Language 】 interface, press ◄ or ► to switch the language you want.

3.

Select

OSD H.Pos/OSD V.Pos

to adjust the position of OSD with ◄ or ►.

4.

Select

OSD Timer

to adjust the OSD duration with ◄ or ►:

5Sec~60Sec

.

5.

Select

Transparency

to adjust the OSD transparency value with ◄ or ►.

6.

Press

AUTO

key to return to the main menu after accomplishing the adjustment.

Figure 4.4.3 OSD Setting

7

4.4.4 Other Settings

Purpose:

You can set Mode, Signal Source, Aspect Ratio, DCR.

Steps:

1.

Press MENU key to enter the main menu interface.

2.

Press triple ◄ key and press MENU key to enter the

Mode

interface, press ◄ or ► to switch the mode between

PC/GAME/MOVIE

.

3.

Press ◄ or ► to change the

Signal Source between

VGA and

HDMI

.

（ Only for DS-D5019Q E-B ）

4.

Press ◄ or ► to switch the

Aspect Ratio between

16:9/AUTO/4:3

.

5.

Press ◄ or ► to switch the

DCR On

/

Off

.

6.

Press

Menu

key to return to the main menu after accomplishing the adjustment.

Figure4.4.4 Other Settings

8

4.4.5 Reset Setting

Purpose:

You can reset settings to the factory defaults.

Steps:

1.

Press MENU key to enter the main menu interface.

2.

Press ◄ key 4 times and press

MENU key to reset settings to the factory defaults.

Figure 4.4.5 Reset Setting

9

Appendix: Specifications

Device Model ST-HDLED18.5

Display Type

Screen Size

Dot Pitch

Max Resolution

Best Operation Resolution

Brightness

Contrast

Response Time

Color

Viewable Area

Viewing Angle

Interfaces

TFT-LED Backlight

18.5"

0.300×0.300 mm

1366×768

1366×768@60Hz

200cd/m²

600:1

5ms

16.7M

409.8×230.4mm

Horizontal 90°, Vertical 65º

VGA Input Port

HDMI Input Port

( Only for DS-D5019QE-B)

AC Input Port

AC 100-240V; 50/60Hz

≤25W

Power Supply

Consumption

Standby Power

Consumption

Operation Temperature

Operation Humidity

Storage Temperature:

Storage Humidity:

Bezel Material

Bezel Color

Wall-mounting Dot Site

Wall-mounting Thread

Device Dimensions

Package Dimensions

G.W.

N.W.

Standard Package

≤0.5W

0°C~40°C (32°F~104°F)

10%~85%

-20°C~55°C (-4°F~131°F)

5%~95%

Plastic

Black

75×75mm

M4

446×3 35×148mm

490×333×101mm

3.5Kg

2.8Kg

Display Unit

VGA Cord

User Manual

Power Cord

1

1

1

1

1

1

1

10

Structure Figure

11

12

SECURITYTRONIX 1-Year Limited LED Display Warranty

Securitytronix. (the "Company") warrants to the Original Purchaser that the LED Display is free from defects in workmanship or material under normal use. This warranty starts on the date of shipment of the hardware to the Original Purchaser.

During the warranty period, the Company agrees to repair or replace, at its sole option, without charge to Original Purchaser, any defective component in the LED Display. To obtain service, the Original

Purchaser must return the LED Display to the Company properly packaged for shipping. All defective products must be returned to the Company within thirty (30) days of failure. Products must be returned with a description of the failure and Return Merchandise Authorization (RMA) number supplied by the

Company. To receive a RMA number and a return shipping address on where to deliver the hardware, call 610-429-1821. The shipping, and insurance charges incurred in shipping to the Company will be paid by Original Purchaser, and all risk for the hardware shall remain with the Original Purchaser until such time as Company takes receipt of the hardware. Upon receipt, the Company will promptly repair or replace the defective unit, and then return said unit to Original Purchaser, shipping prepaid. The

Company may use reconditioned or like-new parts or units, at its sole option, when repairing any hardware. Repaired products shall carry the same amount of outstanding warranty as from original purchase. Any claim under the warranty must include dated proof of purchase or invoice. In any event, the Company's liability for defective hardware is limited to repairing or replacing the hardware.

This warranty is contingent upon proper use of the hardware by Original Purchaser and does not cover: if damage is due to Acts of God (including fire, flood, earthquake, storm, hurricane or other natural disaster), accident, unusual physical, electrical, or electromechanical stress, modifications, neglect; misuse, operation with media not approved by the Company, tampering with or altering of the hardware, war, invasion, act of foreign enemies, hostilities (regardless of whether war is declared), civil war, rebellion, revolution, insurrection, military or usurped power or confiscation, terrorist activities, nationalization, government sanction, blockage, embargo, labor dispute, strike, lockout or interruption or failure of electricity, air conditioning, or humidity control, internet, network, or telephone service

The warranties given herein, together with any implied warranties covering the hardware, including any warranties of merchantability or fitness for a particular purpose, are limited in duration to two years from the date of shipment to the Original Purchaser. Jurisdictions vary with regard to the enforceability of warranty limitations, and you should check the laws of your local jurisdiction to find out whether the above limitation applies to you.

The Company shall not be liable to your for loss of data, loss of profits, lost savings, special, incidental, consequential, indirect, or other similar damages arising from breach of warranty, breach of contract, negligence, or other legal action even if the Company or its agent has been advised of the possibility of such damages, or for any claim brought against your by another party. Jurisdictions vary with regard to the enforceability of provisions excluding or limiting liability for incidental or consequential damages.

You should check the laws of your local jurisdiction to find out whether the above exclusion applies to you.

This warranty allocates risks of product failure between Original Purchaser and the Company. The

Company's hardware pricing reflects this allocation of risk and the limitations of liability contained in this warranty. The warranty set forth above is in lieu of all other express warranties, whether oral or written. The agents, employees, distributors, and dealers of the Company are not authorized to make modification to this warranty, or additional warranties binding on the Company. Accordingly, additional statements such as dealer advertising or presentations, whether oral or written, do not constitute warranties by the Company and should not be relied upon.

This warranty gives you specific legal rights. You may also have other rights which vary from one jurisdiction to another.