Security Tronix ST-IP2PTZC Camera Owner's Manual

ST-IP2PTZC
QUICK START GUIDE
www.nacebrands.com
www.securitytronix.com
ST-IP2PTZC QUICK START GUIDE
Thank you for purchasing our product. If there are any questions, or requests, please do
not hesitate to contact the dealer.
This manual applies to Securitytronix Compact PTZ network cameras.
This manual may contain several technical incorrect places or printing errors, and the
content is subject to change without notice. The updates will be added to the new
version of this manual. We will readily improve or update the products or procedures
described in the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of
the security or signaling aspects of this product. UL has only tested for fire, shock or
casualty hazards as outlined in UL’s Standard(s) for Safety, UL60950-1. UL Certification
does not cover the performance or reliability of the security or signaling aspects of this
product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS
WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR
SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.”
1
ST-IP2PTZC QUICK START GUIDE
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits
for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked
with "CE" and comply therefore with the applicable harmonized European
standards listed under the Low Voltage Directive 2006/95/EC, the EMC
Directive 2004/108/EC, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points.
For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot
be disposed of as unsorted municipal waste in the European Union. See the
product documentation for specific battery information. The battery is
marked with this symbol, which may include lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to
your supplier or to a designated collection point. For more information see:
www.recyclethis.info.
2
ST-IP2PTZC QUICK START GUIDE
Safety Instruction
These instructions are intended to ensure that the user can use the product
correctly to avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings Follow
these safeguards to
prevent serious
injury or death.
Cautions Follow these
precautions to prevent
potential injury or
material damage.
Warnings
 All the electronic operation should be strictly compliance with the electrical safety
regulations, fire prevention regulations and other related regulations in your local
region.
 Please use the power adapter, which is provided by normal company. The standard of
the power adapter is 24VAC10% or 12VDC10% (depending on models). The power
consumption cannot be less than the required value.
 Do not connect several devices to one power adapter as adapter overload may cause
over-heat or fire hazard.
 Please make sure that the power has been disconnected before you wire, install or
dismantle the speed dome.
 When the product is installed on wall or ceiling, the device shall be firmly fixed.
 If smoke, odors or noise rise from the device, turn off the power at once and unplug
the power cable, and then please contact technical support.
 If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the speed dome yourself. (We shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)
Cautions
 Do not drop the dome or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid equipment installation on vibrating surface or
places subject to shock (ignoring this can cause equipment damage).
 Do not place the dome in extremely hot, cold, dusty or damp locations, otherwise fire
or electrical shock may occur. The operating temperature should be -22°F ~ 149°F
(outdoor speed dome) and -14°F ~ 122°F (indoor speed dome).
 The dome cover for indoor use shall be kept from rain and moisture.
3
ST-IP2PTZC QUICK START GUIDE
 Exposing the equipment to direct sun light, low ventilation or heat source such as
heater or radiator is forbidden (ignoring this can cause a fire hazard).
 Do not aim the speed dome at the sun or extra bright places. A blooming or smear
may occur (which is not a malfunction), and affecting the endurance of the sensor at
the same time.
 Please use the provided glove when open up the dome cover, avoid direct contact
with the dome cover, because the acidic sweat of the fingers may erode the surface
coating of the dome cover.
 Please use a soft and dry cloth when clean inside and outside surfaces of the dome
cover, do not use alkaline detergents.
 Please keep all wrappers after unpacking them for future use. In case of any failure
occurring, you need to return the speed dome to the factory with the original
wrapper. Transportation without the original wrapper may result in damage on the
speed dome and may lead to additional costs.
4
ST-IP2PTZC QUICK START GUIDE
Table of Contents
1 Overview ...................................................................................................... 6
2 Installation ................................................................................................... 7
2.1 Wall Mounting ......................................................................................................... 7
2.2 In-ceiling Mounting................................................................................................ 10
2.3 Ceiling Mounting ................................................................................................... 12
2.3.1 Wiring For Ceiling Mounting Applications ....................................................... 13
2.3.2 Mounting ........................................................................................................ 13
3 Setting the Dome over the LAN .................................................................. 16
4 Accessing via Web browser ........................................................................ 19
5
ST-IP2PTZC QUICK START GUIDE
1 Overview
Please turn the power off before connect the cables.
The cable interfaces of the network speed dome are shown in the following figure.
The cables are distinguished by different colors. The labels attached on the cables are
for identification.
1
RED
V
AC24 EN
RE V
OW/G AC24
YELL
GREEN/WHITE
RED/WHITE
BLUE/WHITE
AUDIO_GND
AUDIO_IN
AUDIO_OUT
K
BLAC
2
3
Figure 1-1 Overview
Table 1-1 Overview
No.
Description
1
Power Cables
2
Audio Input/Output Cables
3
Network Cable
6
ST-IP2PTZC QUICK START GUIDE
2 Installation
Before you start:
Check the package contents and make sure that the device in the package is in good
condition and all the assembly parts are included.
Note: Do not drag the speed dome with its waterproof cables as shown in Figure 2-1,
otherwise the waterproof performance is affected.
Figure 2-1 Do Not Drag the Cables
2.1 Wall Mounting
Steps:
1. Loosen the two lock screws as shown in the following figure.
2. Remove the lower dome.
Back Box
Lock Screw
Lock Screw
Lower Dome
Figure 2-2 Disassemble the Speed Dome
3. Remove the protective lens cover, foam and sticker as shown in the following figure.
4. Install the lower dome back and tighten the two lock screws.
7
ST-IP2PTZC QUICK START GUIDE
Protective
sticker
protectivefoam
Figure 2-3 Disassemble the Speed Dome
5. Drill four M8 screw holes on the wall according to the screw holes of the wall mount.
6. Secure the wall mount to the wall with screws.
Notes:
 For cement wall mounting, you need to use the expansion screw to fix the mount.
The mounting hole of the expansion pipe on the wall should align with the mounting
hole on the mount.
 For wooden wall mounting, you can just use the self-tapping screw to fix the bracket.
 Please make sure that the wall is strong enough to withstand more than 8 times the
weight of the dome and the mount.
Nuts and
Washers
Expansion Screws
Figure 2-4 Install the Wall Mount
7. Wrap the threaded part with the thread tape and rotate the pendant adapter to the
wall mount.
8. Secure the pendant adapter to the wall mount with a set screw as shown in Figure
2-5.
8
ST-IP2PTZC QUICK START GUIDE
9. Loosen the lock screws of the adapter.
②
①
Top View of
Pendant
Adapter
Lock Screw
Pendant Adapter
Lock Screw
Figure 2-5 Install the Pendant Adapter
1
Note: The dimension of pendant adapter is G12.
10. Hook the two ends of the safety rope to the back box of the speed dome and the
wall mount respectively. Route the cables through the mount.
11. Align the direction label of pendant adapter with the label of the back box to install
the speed dome as shown below.
②
①
③
④
Figure 2-6 Align the Labels
12. Rotate the back box clockwise tightly. Secure the back box and the pendant adapter
with the two lock screws.
9
ST-IP2PTZC QUICK START GUIDE
Lock Screw
Figure 2-7 Tighten the Lock Screws
2.2 In-ceiling Mounting
Before you start:
The in-ceiling mounting is applicable to indoor ceiling construction. The following are
the mandatory preconditions for mounting:
 The height of the space above the ceiling must be more than 250mm.
 The thickness of the ceiling must ranges from 5 to 40mm.
 The ceiling must be strong enough to withstand more than 4 times the weight of the
dome and its accessories.
Steps:
1. Rotate the lower dome counterclockwise to separate it from the back box as shown in
Figure 2-8.
2. Remove the protective lens cover, foam and sticker from the dome drive.
3. Attach lower dome to the back box, and rotate clockwise to secure it.
Foam
Back Box
Lower Dome
Sticker
Figure 2-8 Remove the Protective Accessory
4. Drill a hole on the ceiling according to the drill template (supplied).
10
ST-IP2PTZC QUICK START GUIDE
Note: ±2mm of the diameter of the circle is tolerable.
Φ 224
Figure 2-9 Draw and Cut a Hole on the Ceiling
5. Connect the cables.
The cables have been connected to the corresponding interfaces. Connect the power
cable and the red LED indicator turns on when the power is on.
Note: Please turn the power off after checking the speed dome.
6. Install the speed dome to the ceiling.
Steps:
1). Loosen the two lock screws on both sides of the back box and make the locks in
internal position, as shown in the following figure:
Lock
Lock
Figure 2-10 Locks and Lock Screws
2). Push the speed dome into the mounting hole in the ceiling.
3). Tighten the lock screws with the screwdriver and the locks will automatically
rotate outwards to secure the in-ceiling mount to the ceiling.
11
ST-IP2PTZC QUICK START GUIDE
Ceiling
Lock
Lock
Screw
Figure 2-11 Install the back box
7. Install the trim ring.
Steps:
1). Attach the trim ring to the lower dome and align the triangular notch of the trim
ring with the arrow label on the in-ceiling mount.
2). After having firmly placed the trim ring to the ceiling, rotate the trim ring in the
direction of arrow to secure the trim ring in place.
Notes:
 Please remove the protective film on the lower dome after the installation is finished.
 In order to obtain clear video images, please wear the anti-static gloves when you
install the speed dome.
Arrow label
Notch
Figure 2-12 Install the Trim Ring
2.3 Ceiling Mounting
Before you start:
 The thickness of the ceiling must ranges from 5 to 40mm.
12
ST-IP2PTZC QUICK START GUIDE
 The ceiling must be strong enough to withstand more than 4 times the weight of the
dome and its accessories.
2.3.1 Wiring For Ceiling Mounting Applications
The cables of the dome can be routed either from the top or the side of the back box,
as shown in Figure 2-13. For the cables routed from the top of the back box, it is
required to drill a cable hole in the ceiling.
Figure 2-13 Cabling for Ceiling Mounting
2.3.2 Mounting
Before you start:
 If the speed dome is installed to a wooden wall, use the self-tapping screws to
secure the mounting base.
 If the dome is installed to a cement wall, drill three Φ5 screw holes onto the wall
according to the hole locations, and then secure the mounting base to the wall with
expansion screws.
Steps:
1. Rotate the lower dome counterclockwise to separate it from the back box.
2. Remove the protective lens cover, foam and sticker from the dome drive.
Foam
Back Box
Lower Dome
Sticker
Figure 2-14 Remove the Protective Accessory
3. Attach lower dome to the back box, and rotate clockwise to secure it.
4. Use the mounting base as a template to mark four screw holes onto the ceiling.
13
ST-IP2PTZC QUICK START GUIDE
5. If you route cables from the top of the back box, mark the cable hole on the ceiling
and drill a hole.
6. Secure the mounting base to the ceiling with set screws.
Screw Holes
Cable
Hole
Figure 2-15 Mark the Screw Positions
 If the speed dome is installed to a wooden wall, use the self-tapping screws to secure
the mounting base.
 If the dome is installed to a cement wall, drill three Φ5 mounting holes onto the wall
according to the hole locations, and then insert the cement screws into the holes and
finally use self-tapping screws to secure the mounting base to the wall.
7. Install the speed dome to the mounting base.
Steps:
1). Route the cables for the speed dome. Align the bottom of the speed dome with
the mounting base.
2). Line up the direction of arrow with the spring end of the mounting base.
3). Push the speed dome upwards and then forwards in the direction of arrow. When
the speed dome is placed in position, the spring will automatically snap into the
lock clip firmly. Refer to the following figure.
14
ST-IP2PTZC QUICK START GUIDE
Push forwards
Line
up
Push upwards
Spring
Lock clip
Figure 2-16 Attach the Back Box to the Mounting Base
Notes:
 Please remove the protective film on the lower dome after the installation is finished.
 Do not touch the bubble of the lower dome directly by hand. The image blurs
otherwise.
15
ST-IP2PTZC QUICK START GUIDE
3 Setting the Dome over the LAN
To view and configure the speed dome via LAN(Local Area Network), you need to
connect the network speed dome in the same subnet as your PC. Then, install the
SADP or client software to search and change the IP of network speed dome.
 The following figure shows the cable connection of network speed dome
to PC.
PC
Speed Dome
Net
Switch
NVR
Figure 3-1 Wiring over LAN
 Set the IP address of the speed dome for accessing via LAN.
Steps:
1. To get the IP address, you can choose either of the following methods:
 Use SADP, a software tool which can automatically detect network speed domes
in the LAN and list the device information like IP address, subnet mask, port number,
device serial number, device version, etc., shown in Figure 3-2.
 Use client software to list the online devices. Please refer to the user manual of
client software for detailed information.
2. Change the IP address and subnet mask to the same subnet as of your PC.
Refer to the following instructions to set IP address with SADP software:
 Search active devices online
Search online devices automatically:
After launching the SADP software, it automatically searches the online devices
every 15 seconds from the subnet where your computer is located. It displays the
total number and information of the searched devices in the Online Devices
interface. Device information including the device type, IP address, port number,
gateway, etc. will be displayed.
16
ST-IP2PTZC QUICK START GUIDE
Figure 3-2 Searching Online Devices
Note: Devices can be searched and displayed in the list 15 seconds after it goes
online; it will be removed from the list 45 seconds after it goes offline.
Search online devices manually:
You can also click
to refresh the online device list manually. The
newly searched devices will be added to the list.
Note: You can click
you can click
or
on each column heading to order the information;
to show the device table and hide the network parameter
panel on the right side, or click
to show the network parameter panel.
 Modify device information
Steps:
1). Select the device to be modified in the device list as shown in Figure 3-3. The
network parameters of the device will be displayed in the Modify Network
Parameters panel on the right side as shown in Figure 3-4.
2). Edit the modifiable network parameters, e.g. IP address and port number.
3). Enter the password of the admin account of the device in the Password field and
click
to save the changes.
17
ST-IP2PTZC QUICK START GUIDE
Figure 3-3 Select a Device
Figure 3-4 Modify Network Parameters
3. Enter the IP address of the speed dome in the address field of the web browser to view
the live video.
Notes:
 The default IP address is 192.0.0.64. The default user name of administrator is admin,
and password is 12345.
 For accessing the network speed dome from different subnets, please set the gateway
for the network speed dome after you log in.
18
ST-IP2PTZC QUICK START GUIDE
4 Accessing via Web browser
System Requirement:
Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 /
Server 2003 / Server 2008 32bits
CPU: Intel Pentium IV 3.0 GHz or higher
RAM: 1G or higher
Display: 1024×768 resolution or higher
Web Browser: Internet Explorer 7.0 and above version, Apple Safari 5.02 and above
version, Mozilla Firefox 3.5 and above version and Google Chrome8 and above version
Steps:
1. Open the web browser.
2. In the browser address bar, input the IP address of the network speed dome, e.g.,
192.0.0.64 and press the Enter key to enter the login interface.
3. Input the user name and password.
4. Click
.
Figure 4-1 Login Interface
5. Install the plug-in before viewing the live video and managing the network speed
dome. Please follow the installation prompts to install the plug-in.
Note: You may have to close the web browser to finish the installation of the plug-in.
19
ST-IP2PTZC QUICK START GUIDE
Figure 4-2 Download Plug-in
Figure 4-3 Install Plug-in
6. Reopen the web browser after the installation of the plug-in and repeat the above
steps 2-4 to login.
Note: For detailed instructions of further configuration, please refer to the user
manual of network speed dome.
For further assistance and troubleshooting, please contact SecurityTronix tech support at: (800)
688-9282, press 3 for Tech Support, then press 2 for CCTV.
20
SECURITYTRONIX 1-Year Limited PTZ Camera Warranty
Securitytronix. (the "Company") warrants to the Original Purchaser that the PTZ Camera is free
from defects in workmanship or material under normal use. This warranty starts on the date of
shipment of the hardware to the Original Purchaser. During the warranty period, the Company
agrees to repair or replace, at its sole option, without charge to Original Purchaser, any defective
component in the PTZ Camera. To obtain service, the Original Purchaser must return the PTZ
Camera to the Company properly packaged for shipping. All defective products must be returned to
the Company within thirty (30) days of failure. Products must be returned with a description of the
failure and Return Merchandise Authorization (RMA) number supplied by the Company. To receive
a RMA number and a return shipping address on where to deliver the hardware, call 610-429-1821.
The shipping, and insurance charges incurred in shipping to the Company will be paid by Original
Purchaser, and all risk for the hardware shall remain with the Original Purchaser until such time as
Company takes receipt of the hardware. Upon receipt, the Company will promptly repair or replace
the defective unit, and then return said unit to Original Purchaser, shipping prepaid. The Company
may use reconditioned or like-new parts or units, at its sole option, when repairing any hardware.
Repaired products shall carry the same amount of outstanding warranty as from original purchase.
Any claim under the warranty must include dated proof of purchase or invoice. In any event, the
Company's liability for defective hardware is limited to repairing or replacing the hardware. This
warranty is contingent upon proper use of the hardware by Original Purchaser and does not cover:
if damage is due to Acts of God (including fire, flood, earthquake, storm, hurricane or other natural
disaster), accident, unusual physical, electrical, or electromechanical stress, modifications, neglect;
misuse, operation with media not approved by the Company, tampering with or altering of the
hardware, war, invasion, act of foreign enemies, hostilities (regardless of whether war is declared),
civil war, rebellion, revolution, insurrection, military or usurped power or confiscation, terrorist
activities, nationalization, government sanction, blockage, embargo, labor dispute, strike, lockout
or interruption or failure of electricity, air conditioning, or humidity control, internet, network, or
telephone service The warranties given herein, together with any implied warranties covering the
hardware, including any warranties of merchantability or fitness for a particular purpose, are
limited in duration to one year from the date of shipment to the Original Purchaser. Jurisdictions
vary with regard to the enforceability of warranty limitations, and you should check the laws of
your local jurisdiction to find out whether the above limitation applies to you. The Company shall
not be liable to your for loss of data, loss of profits, lost savings, special, incidental, consequential,
indirect, or other similar damages arising from breach of warranty, breach of contract, negligence,
or other legal action even if the Company or its agent has been advised of the possibility of such
damages, or for any claim brought against your by another party. Jurisdictions vary with regard to
the enforceability of provisions excluding or limiting liability for incidental or consequential
damages. You should check the laws of your local jurisdiction to find out whether the above
exclusion applies to you. This warranty allocates risks of product failure between Original Purchaser
and the Company. The Company's hardware pricing reflects this allocation of risk and the
limitations of liability contained in this warranty. The warranty set forth above is in lieu of all other
express warranties, whether oral or written. The agents, employees, distributors, and dealers of the
Company are not authorized to make modification to this warranty, or additional warranties
binding on the Company. Accordingly, additional statements such as dealer advertising or
presentations, whether oral or written, do not constitute warranties by the Company and should
not be relied upon. This warranty gives you specific legal rights. You may also have other rights
which vary from one jurisdiction to another.