Smart Technologies Senteo Quick Start Guide
SMART Technologies Senteo is an interactive response system that engages students and facilitates real-time assessment. With 24/32 clickers, a receiver, and user-friendly software, educators can create interactive lessons, polls, quizzes, and activities. Senteo seamlessly integrates with SMART Notebook software, enabling teachers to incorporate interactive elements into their lessons.
Advertisement
Advertisement
SMART Technologies
Senteo™
Interactive Response System
Quick Start Guide
Table of Contents
Safety and Compliance Information ................................... 2
What’s in the Box? ..................................................... 5
System Requirements................................................ 6
Environmental Considerations ........................................... 6
Installing the Batteries ............................................... 7
Installing Senteo Software......................................... 7
Installing SMART Board Driver Software ........................... 9
Activating Senteo Assessment Software................. 10
Installing and Setting Up Your Senteo System ............11
Connecting the Senteo Receiver........................................ 11
Starting the Senteo Interactive Response System.. 13
Setting Up Senteo Teacher ................................................ 13
Connecting to a Class ........................................................ 15
Creating Class Lists in Senteo Teacher ............................. 16
Adding Questions with the Insert Question Wizard ............ 17
Disconnecting the Clickers ....................................... 19
Disconnecting Clickers Using Senteo Teacher .................. 19
Disconnecting Individual Clickers Using Senteo Teacher .. 19
Waste Electrical and Electronic Equipment Regulations 20
Safety and Compliance Information
NOTE:
If you own a SMART product other than a SMART Senteo™ interactive response system, refer to the installation manual that came with your SMART product for relevant warnings and maintenance instructions.
The Senteo receiver and clickers do not contain user serviceable parts. Do not open them. If you suspect that they are faulty, contact an authorized SMART service representative.
WARNING
Failure to follow the installation instructions that ship with the SMART product could result in personal injury or damage to the product.
WARNING
Ensure that any cables extending across the floor to your SMART product are properly bundled and marked to avoid a trip hazard.
WARNING
To reduce the risk of fire or electric shock, do not expose the SMART product to rain or moisture.
CAUTION
Wipe the units with a clean, damp cloth. Never use cleaning fluid or solvents. Do not spray cleaner directly on units.
CAUTION
Use only the batteries provided or equivalent replacements. Do not attempt to recharge the batteries.
CAUTION
Do not install batteries with the polarity (+/–) reversed.
2
Safety and Compliance Information
CAUTION
Do not dispose of batteries in a fire or incinerator.
Dispose of batteries according to the laws and regulations of your region. If you don’t know the applicable rules for your region, consult the battery manufacturer.
IMPORTANT
You must connect the USB cable that came with your SMART product to a computer that has a USB compliant interface and that bears the
USB logo. In addition, the USB source computer must be compliant with CSA/UL/EN 60950 and bear the CE mark and CSA and/or UL
Mark(s) for CAS/UL 60950. This is for operating safety and to avoid damage to the SMART product.
IMPORTANT
If your SMART product requires replacement parts, make sure the service technician uses replacement parts specified by SMART
Technologies or parts with the same characteristics as the original.
Safety and Compliance Information
3
Compliance
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications to this equipment not expressly approved by SMART
Technologies ULC may void the user’s authority to operate this equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiver or clicker units.
• Increase the distance between the equipment and the product.
• Connect the affected equipment to an outlet on a circuit different from that to which the receiver’s computer is connected.
• Consult your SMART service representative or an experienced radio TV technician for help.
For More Information
For more safety warnings and information about Senteo products, consult the
Senteo
Interactive Response System User’s Guide
found on the Senteo software CD. You can also consult the Senteo online Help system for information about Senteo software’s features.
Contacting SMART Technologies
Visit SMART’s support site at
www.smarttech.com/support
to check for software upgrades, including SMART Notebook software and Senteo assessment software. You’ll find installation and user's guides, how-to and troubleshooting articles, solutions for your
SMART product, and answers to your questions. You can also use SMART’s support site to contact technical support.
4
Safety and Compliance Information
What’s in the Box?
The shipping carton contains:
• A carrying case that includes:
– 24 or 32 clickers*
– Receiver
– Phillips® No. 1 screwdriver
– Software CD with user documentation
– Senteo Interactive Response System
Quick Start Guide
• 48 or 64 AA batteries*
*
You can purchase Senteo interactive response systems with either 24 or 32 clickers. SMART provides sufficient batteries for the quantity of clickers purchased.
If your kit is missing an item, call your Technical Support representative. We’ll ask for your product’s serial number to ensure that we send the correct part(s).
You can also purchase Senteo receivers separately, and purchase clickers individually or in packs of five. Contact your local SMART reseller for details.
Online Information and Support
Visit www.smarttech.com/support to view and download user’s guides, how-to and troubleshooting articles, software and more.
Technical Support
If you experience difficulty with your SMART product, please contact your local reseller before contacting SMART Technical Support. Your local reseller can resolve most issues without delay. To locate your local reseller, visit www.smarttech.com/us/where+to+buy
Online
Telephone www.smarttech.com/contactsupport
+1.403.245.0333
Toll Free 1.866.518.6791 (U.S./Canada)
(Monday to Friday, 5 a.m. – 6 p.m. Mountain Time)
What’s in the Box?
5
6
System Requirements
Minimum Requirements – Windows® 2000 SP4
Pentium® III 500 MHz processor with 256 MB of RAM
331 MB of free hard disk space for minimum installation
Microsoft® Internet Explorer® 6.0 or later
Adobe® Flash® Player version 9
Recommended Requirements – Windows XP SP2 or SP3
Pentium III 1 GHz processor with 512 MB of RAM
1.2 GB of free hard disk space for full installation with Gallery collections
Microsoft Internet Explorer 6.0 or later
Adobe Flash Player version 9
Advanced Requirements – Windows Vista® SP1
1.5 GHz Intel® Core Duo processor with 1 GB of RAM
1.2 GB of free hard disk space for full installation with Gallery collections
Microsoft Internet Explorer 6.0 or later
Adobe Flash Player version 9
Minimum Requirements – Mac OS X 10.4.11
1 GHz Power PC G4 processor with 384 MB of RAM
480 MB of free hard disk space for minimum installation
Adobe Flash Player version 9
Recommended Requirements – Mac OS X 10.4.11
1 GHz Power PC G5 or Intel processor with 512 MB of RAM
1.5 GB of free hard disk space for full installation with Gallery collections
Adobe Flash Player version 9
Advanced Requirements – Mac OS X 10.5.5
1.5 GHz Intel Core Duo processor with1 GB of RAM
1.5 GB of free hard disk space for full installation with Gallery collections
Adobe Flash Player version 9
NOTES:
- 1 MB = 1024² bytes, 1 GB = 1024³ bytes
- Senteo software can’t be used with an Intel Itanium® processor
- Senteo software runs on 32- bit operating systems
Environmental Considerations
Operating temperature range: 41°F to 95°F (5°C to 35°C) up to 80% relative humidity (non condensing)
Storage temperature range: -40°F to 120°F (-40°C to 50°C)
System Requirements
Installing the Batteries
1. Use the provided Phillips® No. 1 screwdriver to remove the screw from the back of the clicker and then remove the cover.
2. Insert the included AA batteries as shown.
The clicker automatically turns on when you insert the batteries.
3. Replace the cover and screw.
4. Verify that the start-up menu appears.
5. Press the
Power
button for one second to turn the clicker off.
Installing Senteo Software
NOTE:
Connect your computer to the Internet before installing Senteo software. You must have an Internet connection to:
• install the Lesson Activity Toolkit and SMART Essentials for Educators.
• download and install SMART Board™ driver software, if required.
To install Senteo software on Windows computers
1. Insert the Senteo interactive response system CD into your computer’s drive.
The installation wizard appears.
If it doesn’t start automatically, locate and double-click the
CDBrowser.exe
file on the CD.
2. Click
Install Senteo Software
to start the wizard, and then click
Next
.
The
Licence Agreement
dialog box appears.
3. Select the
I accept
option, and click
Next
.
4. Click
Next
to install the Senteo and SMART Notebook software in the default folders.
5. If desired, type your name and Organization into the text boxes, and then click
Next
.
The
Notebook Software Gallery Collections
dialog box appears.
Installing the Batteries
7
6. Select the
Lesson Activity Toolkit
and
SMART Essential for Educators
options as desired, and then click
Next.
7. Click
Install
to start the installation.
The
Installing the Software
dialog box appears showing the installation progress.
If your computer isn’t connected to the Internet, the
Gallery Setup
dialog box appears indicating that it could not download the Lesson Activity Toolkit and
SMART Essentials for Educators files. Click
OK
.
8. Click
Finish
.
To install Senteo software on Mac computers
1. Insert the Senteo interactive response system CD into your computer’s CD drive.
A
Senteo
CD icon appears on the desktop.
2. Double-click the
Senteo
CD icon.
The
Senteo
window appears.
3. Double-click the
CDBrowser
icon.
The
SMART Senteo Software
dialog box appears.
4. Click
SMART Senteo Software
, and then click
Continue
.
The
Install Senteo
dialog box appears.
5. Click
Continue
.
The
Software License Agreement
page appears.
6. Click
Continue
, and then click
Agree
, if you agree with the terms of the license agreement.
The
Gallery Collections
dialog box appears.
7. Select the galleries you want to install, and then click
Continue
.
8. If there is more than one volume, select the volume that you want to install the
Senteo software on, and then click
Continue
.
9. Click
Install
to start the installation.
NOTE:
If the installer asks you to, type your password, and then click
OK
.
10. Click
Continue Installation
to complete the installation.
After a short delay, the
SMART Product Update
dialog box appears. If your computer is connected to the Internet, the dialog box displays the current versions of your SMART product software, and displays the latest updates available for download from SMART’s website.
8
Installing Senteo Software
11. If software updates are available, click
Update
.
OR
If software updates aren’t available, or if you don’t want to update your software, click
Close
.
If your computer isn’t connected to the Internet, a dialog box appears indicating that it could not download the SMART Essentials for Educators files. Click
OK
After a short delay, a message appears asking you to restart your computer.
12. Click
Restart
.
Installing SMART Board Driver Software
Before you connect your computer to a SMART Board interactive whiteboard, you must download and install SMART Board driver software from SMART’s website.
NOTE:
If SMART Notebook 10 software was installed on your computer before you installed Senteo 2.0, you don’t need to perform this procedure.
To install SMART Board drivers
1. In your Internet browser, go to one of the following links:
– If you have a Windows computer: http://downloads.smarttech.com/techsupport/k1fi2rh8stf3eja6kjs1sdl0wa/ smartboarddriverssetupsp2.zip
– If you have a Mac computer: http://downloads.smarttech.com/techsupport/k1fi2rh8stf3eja6kjs1sdl0wa/ smartboarddriverssp2macinstall.zip
2. Follow the instructions to install the software.
Installing Senteo Software
9
Activating Senteo Assessment Software
You must register your Senteo software within 30 days of installation to keep it active. If the activation isn’t successful, use the following procedure to find your license code and activate the software.
IMPORTANT
Senteo software automatically activates when you plug in your Senteo receiver. If the activation isn’t successful, use the following procedure to find your license code and activate the software.
After you complete the following procedure to find your license code, use the code to activate Senteo software on other computers, as outlined in the
License
tab in the
About Senteo Assessment Software
dialog box.
NOTE:
After you find your license code, you don’t need to connect the Senteo receiver to the other computers that you want to activate Senteo software on.
To find the license code after the software is activated
1. Click the
Senteo
icon in the Windows notification area or Mac menu bar, and then select
About Senteo Assessment Software
.
2. Record the license code that appears on the
Description
tab.
To activate Senteo assessment software on other computers
NOTE:
You don't need to connect your Senteo receiver during this procedure.
1. Click the
Senteo
icon in the Windows notification area or Mac menu bar, and then select
Activate Senteo Assessment Software
.
The
Senteo Software Evaluation
dialog box appears and displays the time remaining in your software evaluation period.
2. Click
Activate Now
.
If a dialog box appears requesting a password, type the administrator’s password.
3. Type your license code and e-mail address, and then click
Next
.
4. Click
Finish
.
Your Senteo software activates.
10
Activating Senteo Assessment Software
Installing and Setting Up Your Senteo
System
Connecting the Senteo Receiver
IMPORTANT
For operating safety and to avoid damage to the receiver, you must only connect the receiver’s USB connector to a computer that has a
USB compliant interface and that bears the USB logo. In addition, the
USB source computer must be compliant with CSA/UL/EN 60950 and bear the CE mark and CSA and/or UL mark(s) for CSA/UL 60950.
The receiver has a USB 2.0 full-speed peripheral interface that runs at speeds of up to
12 Mbps. The unit works with USB 2.0- and USB 1.1-complaint USB interfaces.
Recommended Height for Mounting the Receiver
Although receivers don’t require an unobstructed line-of-sight transmission path, such as that required by infrared devices, you can operate the Senteo system over larger distances if you minimize interference, signal reflections and the number and size of objects between the receiver and the clickers.
Choose a location for the receiver that is as high as possible, and in plain view of the students’ clickers. For permanent installations, use a USB extender to mount the receiver high on a wall. To minimize interference from other radio–frequency equipment, position the receiver away from other wireless products, such as 2.4 GHz routers and cordless telephones.
WARNING
To prevent product damage or personal injury, route the USB cable where it will not be stepped on or tripped over.
Installing and Setting Up Your Senteo System
11
To connect the receiver
1. Position the receiver in an unobstructed location away from other wireless products, such as 2.4 GHz routers and cordless telephones.
For temporary installations, place the receiver on top of your desk. For permanent installations, mount the receiver on a wall or on the front of a piece of furniture using two screws
(not provided).
Permanent
Vertical
Installation
Temporary
Desktop
Installation
Orient the receiver with the long side or edge facing the class as shown.
NOTE:
The operating system should automatically detect and configure the hardware drivers. After a few seconds, a message appears indicating that your hardware is ready to use. Click the
Senteo Desktop
Menu
to check that there is only one receiver connected. For Windows users, follow the instructions below if you are unable to automatically configure your hardware.
2. Insert the receiver’s captive USB cable’s connector into an available USB receptacle on your computer.
– On Windows computers, a balloon message appears in the notification area indicating that new hardware has been detected.
– On Mac computers, a balloon message appears indicating that the hardware is ready to use. The top LED indicator on the receiver turns red to indicate that it is receiving power.
IMPORTANT
If the balloon message indicates that Windows is starting to try to locate a driver from the Microsoft website, stop the search. If Windows can’t find the driver on your computer, you haven’t installed the Senteo software. Install the software and repeat the above procedure.
12
Installing and Setting Up Your Senteo System
Starting the Senteo Interactive Response
System
The Senteo interactive response system is an assessment tool designed to enhance learning. You can pose questions during your presentation or lesson to make sure your audience is on track, or create a question set and use it as a formal assessment tool.
Before you begin, make sure the Senteo assessment software has been installed on your computer.
Setting Up Senteo Teacher
Before you can use Senteo software, you must:
• name your classroom and create a Teacher file
• decide on the mode of operation
• start a Senteo class, or start in Anonymous Mode
Naming Your Classroom
To name the classroom and create a Teacher file
1. Click the
Senteo
icon in the Windows notification area or menu bar, and then click on the icon below
Senteo Teacher
.
Senteo Teacher
appears.
NOTE:
The wizard appears if you haven’t already assigned a classroom name. If you previously assigned a classroom name, Senteo Teacher appears in
Anonymous Mode.
2. Type a classroom name between one and eight characters in length, and then click
Begin
.
3. Click
Create a new SMART Teacher file....
The
Gradebook Information
dialog box appears.
4. Type your name and school information into the text boxes, and then click
Done
.
Starting the Senteo Interactive Response System
13
Before starting a class, you must decide whether you want the system to operate in
Anonymous Mode
, or
Sign In Mode
. The following table summarizes each mode’s characteristics.
Modes of Operation
Anonymous Mode Sign In Mode
You can operate the system without a class list.
Students can connect their clickers without identifying themselves.
Your class list must identify each student by name, and a unique ID #.
Students can connect their clickers, but must sign in with their assigned ID #.
Under the teacher’s supervision, students can view their own grades, but they can’t see other students’ grades.
Under the teacher’s supervision, students can view their own grades, but they can’t see other students’ grades.
Teachers can see how many clickers are connected.
Teachers can identify individual students as they connect, and sign in with their clickers.
Teachers can see, export, and print the total class score.
Teachers can see, export and print total scores for each question.
Teachers can see, export and print the total class score.
Teachers can see, export and print total scores for each question.
Teachers can’t identify students’ names, or their individual scores.
Teachers can see, export, and print each student’s score for each question, and their total score.
To start a class in Anonymous mode
NOTE:
In this mode, a class list isn’t required to operate Senteo software in Anonymous mode.
1. Click the
Senteo
icon in the Windows notification area or the Mac menu bar, and then select
Senteo Teacher
.
2. If Senteo Teacher opens to
Basic View
, click the
Start a Class
button, and then select
Anonymous Mode
from the drop-down list. If Senteo Teacher opens to
Gradebook View
, select
Anonymous Mode,
and then click
Start Class
.
The receiver’s power LED flashes, and then turns solid green. The receiver’s transmit LED flashes green. You can now ask the students to turn on and connect their clickers.
14
Starting the Senteo Interactive Response System
To start a class in Sign In mode
NOTE:
In this mode, you must have a class list before you can start a Senteo class and connect the clickers.
1. If Senteo Teacher opens to
Basic View
, click the
Start a Class
button, and then select the class from the drop-down list. If Senteo Teacher opens to
Gradebook
View,
select the class from the area below Gradebook, and then click
Start Class
.
The receiver’s power LED flashes, and then turns solid green. The receiver’s transmit LED flashes green. You can now ask the students to turn on and connect their clickers.
Connecting to a Class
Students need to know the classroom’s name, and they must sign in with a unique ID number.
TIP
You can start asking questions before students have signed in. This is common practice if you want to ask the students questions with regard to a particular homework assignment.
To connect to a class in Sign-in Mode
Have your students follow these instructions, once your class begins.
1. Press the clicker’s
Power
button for one second.
A message appears asking if you want to join the class the clicker was last connected to, or find a different class.
2. Press the
Enter
button to join the last class.
OR
Press the
Down
button to select
Find a class
, and then press
Enter
.
The clicker searches for classes, and then displays a list of classes within range.
3. Press the
Up
and
Down
buttons to select the correct class, and then press
Enter
.
A message appears asking for an ID number.
4. Press the number buttons to enter your
ID
number, and then press
Enter.
A message appears requesting you to confirm your name.
NOTE:
If the teacher has selected the
Lock Sign In
option, the clicker returns to the
ID
screen.
5. Press the
Enter
button to connect.
A
welcome
message appears. Once your students are connected, you can start asking questions.
Starting the Senteo Interactive Response System
15
Creating Class Lists in Senteo Teacher
You don’t need to create a class list if you are starting a class in Anonymous mode.
To create a class list
1. Click the
Senteo
icon in the Windows notification area, or Mac menu bar, and then select
Click Here to Start a Class
.
Senteo Teacher starts.
2. Click
Switch to Gradebook view,
if it isn’t already selected.
3. Click
Add a Class
in the
Gradebook
area on the left.
4. Type your class name and other details into the
Class Information
boxes, and then click
Add
.
The
new class
’ window opens, and the class name appears in the
Gradebook
area.
5. Click the
Students
tab at the top of the window.
6. Click an empty row in the table.
The
student properties window appears.
7. Type a student’s name in the
Name
box. The last name and other information is optional. You can use tags to categorize the students into custom groupings that
Senteo uses when you create students reports.
8. Type a unique number between 1 and 15 digits into the
ID
box.
The student information saves to the class list as you enter it.
9. Repeat steps 5 to 8 for each student.
16
Starting the Senteo Interactive Response System
Adding Questions with the Insert Question Wizard
To add a question using the Insert Question wizard
1. Click the
Senteo Assessment Software
icon in the Windows notification area or
Mac menu bar, and then select
Open Notebook Software
below the
Ask Questions
heading.
2. Select
New Notebook File
to create a new file.
SMART Notebook software opens with a blank page.
3. Select
Senteo > Insert Question
.
The
Insert Question
wizard appears.
4. Click the thumbnail for the desired question type, and then click
Next
.
5. For
Yes
or
No
, and
True
or
False
questions, select the correct answer, or the
Opinion
option.
For
Number, fraction, decimal questions
, type the correct answer.
For
Multiple choice,
or
Multiple answer
questions, select the number of answers, type the answers into the text boxes, click
Next
, and then select the correct answers or the
Opinion
option.
NOTE:
For multiple answer questions, you can only create a maximum of six answers.
6. Assign the number of points the student receives if they answer the question correctly.
7. If you want to create more questions, click
Insert Another
, and then repeat steps 4 to 6.
OR
If this is your last question, click
Finish
.
You can use SMART Notebook software’s tools to add images or Adobe Flash objects from the SMART Notebook Gallery, if desired.
Starting the Senteo Interactive Response System
17
Question Types
Using Notebook Senteo software, you can ask five types of questions, either individually, or as question sets. You can also add notes to any question type that appears when you print the question results.
Question Type
Yes or No
Multiple Choice
Number, Fraction or
Decimal
True or False
Multiple Answer
Description
Students must press the
Y
or
N
buttons to answer a question. You can also select the
Opinion
option to allow any answer.
Students must press a single button,
A
through
J
, to answer the question. Select from 2 to 10 answers for a question. You can also select the
Opinion
option to allow any answer.
Ask a question with a numeric answer using whole numbers, fractions, or decimals.
Students must press the
T
or
F
buttons to answer a question. You can also select the
Opinion
option to allow either answer.
Students use the
A
through
J
buttons to select the correct combination of answers to the question. Select from
2
to
6
answers for the question. You can also select the
Opinion
option to allow any combination of answers.
18
Starting the Senteo Interactive Response System
Disconnecting the Clickers
Disconnecting Clickers Using Senteo Teacher
You can disconnect and turn off all clickers simultaneously.
To disconnect all clickers using Senteo Teacher
1. Click the
Senteo
icon in the Windows notification area or Mac menu bar, and select
Senteo Teacher
.
2. Select a class in the Gradebook area, and then click
Stop Class
.
A message appears on the clickers indicating that the class is over, and that the clickers are turning off. The receiver’s transmit and receive LEDs turn off and the power LED turns red.
All student clickers disconnect and turn off.
Another way to disconnect all clickers
1. Click the
Senteo
icon in the Windows notification area, or Mac menu bar, and select
Senteo teacher
.
2. Select
Devices
, and then click
Turn off all clickers
.
All student clickers disconnect and turn off.
Disconnecting Individual Clickers Using Senteo Teacher
To disconnect individual clickers using Senteo Teacher
1. Click the
Senteo
icon in the Windows notification area or Mac menu bar, and then select
Senteo Teacher
.
2. Select the active class in the
Gradebook
area.
3. Click the
Students
tab.
4. Select the row of the student that you want to disconnect.
The
Properties
window appears below the student list table.
5. Click the
Disconnect Clicker
button at the top-right of the window.
All student clickers disconnect and turn off.
Disconnecting the Clickers
19
Waste Electrical and Electronic Equipment
Regulations
This section contains information about the Waste Electrical and Electronic Equipment
Regulations (WEEE) that apply to all electrical and electronic equipment within the
European Union.
When you dispose of any electrical or electronic equipment, including SMART products, we strongly encourage you to contact your local WEEE recycling agency for recycling and disposal advice.
Your SMART product required the extraction and use of natural resources for its production. It may contain hazardous substances. By disposing of electrical and electronic equipment appropriately, you lower the impact of these substances upon health and the environment and reduce the pressure on natural resources. Recycling agencies can reuse or recycle most of the materials from your product.
Please think about how you intend to dispose of any product that has a WEEE symbol or accompanying WEEE guidelines.
If you need more information on the collection, reuse and recycling of electrical and electronic equipment, please contact your local WEEE recycling agency. Alternatively, contact your local reseller or SMART Technologies for information on the environmental performance of our products.
SMART Technologies
3636 Research Road NW
Calgary, AB T2L 1Y1
CANADA www.smarttech.com/support www.smarttech.com/contactsupport
Support +1.403.2
28 .
5940 or Toll Free 1.866.518.6791 (Canada/U.S.)
© 2007–2011 SMART Technologies ULC. All rights reserved. SMART Board, the SMART logo, Senteo and smarttech are trademarks or registered trademarks of SMART Technologies ULC in the U.S. and/or other countries. Microsoft Windows and
Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the U.S. and/or other countries. Mac and Mac OS are registered trademarks of Apple Computer, Inc., registered in the U.S. and other countries. All other third-party product and company names may be trademarks of their respective owners. Patent No. US6320597 and US6326954. Other patents pending. Contents are subject to change without notice. 12/2011.
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement