Fisher EZ-C, ET-C, and EWT-C Cryogenic Sliding-Stem Control Valves Instruction manual
Add to My manuals24 Pages
advertisement
Instruction Manual
D102175X012
EZ-C, ET-C, and EWT-C Valves
July 2017
Fisher
™
EZ‐C, ET‐C, and EWT‐C Cryogenic
Sliding‐Stem Control Valves
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scope of Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Educational Services
Installation
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Packing Maintenance
Replacing Packing
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
Trim Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . .
EZ‐C Trim Disassembly . . . . . . . . . . . . . . . . . . .
EZ‐C Trim Assembly . . . . . . . . . . . . . . . . . . . . .
ET‐C and EWT‐C Trim Disassembly . . . . . . . . .
ET‐C and EWT‐C Valve Plug Maintenance
ET‐C and EWT‐C Trim Assembly
. . . .
. . . . . . . . . . .
Coining Soft Metal‐to‐Metal Seats . . . . . . . . .
Parts Ordering
Parts Kits
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bonnet Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EZ‐C Valve Body Parts . . . . . . . . . . . . . . . . . . . . . . .
ET‐C and EWT‐C Valve Body Parts . . . . . . . . . . . . . .
Introduction
Figure 1. Typical Fisher Cryogenic Valve with
Extension Bonnet and 585C Series Actuator
W6370
Scope of Manual
This instruction manual includes installation, maintenance, and parts information for Fisher EZ‐C, ET‐C and EWT‐C
Do not install, operate, or maintain EZ‐C, ET‐C or EWT‐C valves without being fully trained and qualified in valve, actuator, and accessory installation, operation, and maintenance. To avoid personal injury or property damage, it is important to carefully read, understand, and follow all the contents of this manual, including all safety cautions and warnings.
If you have any questions about these instructions, contact your Emerson sales office or Local Business
Partner before proceeding.
Description
EZ‐C: globe‐style, single‐port, unbalanced valves with integral end connections, post guiding, metal‐to‐metal seating, and quick‐change trim. They feature stainless steel construction materials and fabricated extension bonnets.
ET‐C and EWT‐C: metal‐to‐metal seated globe‐style, single‐port, cage‐guided, pressure‐balanced valves featuring stainless steel construction materials and fabricated extension bonnets.
www.Fisher.com
EZ-C, ET-C, and EWT-C Valves
July 2017
Instruction Manual
D102175X012
Table 1. Specifications
Valve Sizes
EZ‐C: NPS J 1, J 1-1/2, J 2, J 3, and J 4
ET‐C: NPS J 3, J 4, J 6, and J 8
EWT‐C: NPS J 6X4 (1) , J 8X4, J 8X6, J 12X6, and
J 10X8
Material Temperature Capability
EZ‐C: -198 to 149
ET‐C and EWT‐C:
-198 to 66 _
_ C (-325 to 300
C (-325 to 150 _ F)
_
(2)
F)
End Connection Styles
(2)
CL150, 300, and 600 raised‐face flanges per ASME
B16.5
Maximum Allowable Actuator Thrust
Maximum Inlet Pressure (2)
CL150 and 300— Valves are consistent with pressure‐temperature ratings per ASME B16.34
CL600— Valves with B8M Class 2 bolting are consistent with CL600 pressure‐temperature ratings per ASME B16.34 except as shown below:
Valve Size, NPS
1
2
3
Flow Characteristics
EZ‐C: Equal percentage, linear, and quick opening
ET‐C and EWT‐C: Equal percentage and linear
Flow Directions
EZ‐C: Up through the seat ring only
ET‐C and EWT‐C : Normally down (4) and IEC 60534‐4
VALVE
EZ‐C
ET‐C and EWT‐C
EZ‐C VALVES
Maximum Inlet Pressure
Bar Psig
77
83
94
1110
1200
1370
Valve Size, NPS
3
6, 8 x 6, 12 x 6
8, 10 x 8
ET‐C AND EWT‐C VALVES
Maximum Inlet Pressure
Bar Psig
94 1370
75
96
1085
1390
CL600— Valves with optional S20910 (XM‐19) bolting are consistent with CL600 pressure‐temperature ratings per ASME B16.34
Shutoff Classifications per ANSI/FCI 70‐2
SHUTOFF CLASS
Class IV—Standard
Class VI—Optional
Class IV—Standard
Class V Air Test (3)
—Optional
Approximate Weights
EZ‐C:
NPS 1: 11 kg (33 lb)
NPS 1-1/2: 23 kg (48 lb)
NPS 2: 41 kg (90 lb)
NPS 3: 60 kg (130 lb)
NPS 4: 95 kg (210 lb)
ET‐C:
NPS 3: 51 kg (135 lb)
NPS 4: 95 kg (210 lb)
NPS 6: 211 kg (465 lb)
NPS 8: 372 kg (820 lb)
EWT‐C
NPS 6X4: 200 kg (440 lb)
NPS 8X4: 277 kg (610 lb)
NPS 8X6: 318 kg (700 lb)
NPS 12X6: 730 kg (1610 lb)
NPS 10X8: 753 kg (1660 lb)
1.Valve size number is end connection size by normal trim size. For example, an NPS 6X4 valve has NPS 6 end connections with NPS 4 trim.
2.Do not exceed the pressure/temperature limits in this manual and any applicable code limitation.
3.Class V Air Test is optional. Test will be 50 psid air. Class V shutoff cannot be performed with water. The residual trapped moisture from testing with water can cause valve and trim damage from ice crystals formed at below freezing service temperatures.
4.Down is in through the cage and out the seal ring. (see figure 9).
2
Instruction Manual
D102175X012
EZ-C, ET-C, and EWT-C Valves
July 2017
Table 2. Maximum Allowable Actuator Thrust for Standard Style 3 Bonnet Extension Length
VALVE SIZE, NPS
STEM DIAMETER
MAXIMUM ALLOWABLE STEM LOAD
FOR S20910 (XM‐19) STEM MATERIAL mm Inches N Lb
1
9.5
12.7
9.5
1-1/2
3/8
1/2
3/8
5382
13166
5338
1210
2960
1200
2
12.7
12.7
19.1
1/2
1/2
3/4
13166
14367
44169
2960
3230
9930
3
4, 6X4, 8X4
6, 8X6, 12X6
8, 10X8
12.7
19.1
12.7
19.1
19.1
25.4
19.1
25.4
1/2
3/4
1/2
3/4
3/4
1
3/4
1
15301
45459
16458
46971
36385
81487
41366
87003
3440
10220
3700
10560
8180
18320
9300
19560
Educational Services
For information on available courses for Fisher EZ-C, ET-C, and EWT-C valves, as well as a variety of other products, contact:
Emerson Automation Solutions
Educational Services - Registration
Phone: 1-641-754-3771 or 1-800-338-8158
E-mail: [email protected]
emerson.com/fishervalvetraining
Installation
Isolate the control valve from the line pressure, release pressure from both sides of the valve body, and drain the process media from both sides of the valve. Remove actuator supply pressure, and use lockout procedures to be sure that the above measures stay in effect while you work on the equipment. Refer to the Warnings at the beginning of the
Maintenance section for additional information.
WARNING
Always wear protective gloves, clothing, and eyewear when performing any installation operations to avoid personal injury.
Personal injury or equipment damage caused by sudden release of pressure may result if the valve assembly is installed
damage, provide a relief valve for over‐pressure protection as required by government or accepted industry codes and good engineering practices.
Check with your process or safety engineer for any additional measures that must be taken to protect against process media.
If installing into an existing application, also refer to the WARNING at the beginning of the Maintenance section in this instruction manual.
3
EZ-C, ET-C, and EWT-C Valves
July 2017
Instruction Manual
D102175X012
CAUTION
When ordered, the valve configuration and construction materials were selected to meet particular pressure, temperature, pressure drop, and controlled fluid conditions. Since some valve body/trim material combinations are limited in their pressure drop and temperature ranges, do not apply any other conditions to the valve without first contacting your
Emerson sales office or Local Business Partner.
Before installing the valve, inspect the valve and pipelines for any damage and any foreign material which may cause product damage.
1. Before installing the valve, inspect the valve and associated equipment for any damage and any foreign material.
2. Make certain the valve body interior is clean, that pipelines are free of foreign material, and that the valve is oriented so that pipeline flow is in the same direction as the arrow on the side of the valve.
3. Gas Service: The normal method of mounting for gas service is with the actuator vertical above the valve body.
However, the control valve assembly may be installed in any orientation unless limited by seismic criteria. Other positions may result in uneven valve plug and cage wear that could result in improper operation. For mounting assistance, consult your Emerson sales office or Local Business Partner.
CAUTION
To avoid possible damage to the packing, do not allow the installed actuator angle to be so flat as to allow liquid inside the bonnet to come in contact with the packing.
Also, if insulation is applied, do not let the insulation run up the extension bonnet. This could cause the packing to freeze and be damaged.
Liquid Service: The preferred method of mounting for liquid service is with the actuator vertical above the valve body.
This will allow a vapor layer to form between the liquid and the packing. If there are piping constraints, the actuator can be angled slightly from vertical. However, in no case should the angle be so flat as to allow liquid inside the bonnet to come in contact with the packing. For mounting assistance, consult your Emerson sales office or Local Business
Partner.
4. If insulation is applied, make sure it is applied only to the body/bonnet joint. Do not let the insulation run up the extension bonnet.
5. Use accepted piping and welding practices when installing the valve in the line. For flanged valve bodies, use a suitable gasket between the valve body and pipeline flanges.
6. If the actuator and valve are shipped separately, refer to the actuator mounting procedure in the appropriate actuator instruction manual.
WARNING
Personal injury could result from packing leakage. Valve packing was tightened before shipment; however, the packing might require some readjustment to meet specific service conditions.
Valves with ENVIRO‐SEAL ™ live‐loaded packing will not require this initial readjustment. See the Fisher instruction manual titled ENVIRO‐SEAL Packing System for Sliding‐Stem Valves for packing instructions. If you wish to convert your present packing arrangement to ENVIRO‐SEAL packing, refer to the retrofit kits listed in the parts kit sub‐section near the end of this manual.
4
Instruction Manual
D102175X012
EZ-C, ET-C, and EWT-C Valves
July 2017
Maintenance
Valve parts are subject to normal wear and must be inspected and replaced as necessary. Inspection and maintenance frequency depends on the severity of service conditions. This section includes instructions for packing maintenance and trim maintenance. All maintenance operations may be performed with the valve in the line.
WARNING
Avoid personal injury or property damage from sudden release of process pressure. Before performing any maintenance operations:
D Do not remove the actuator from the valve while the valve is still pressurized.
D Always wear protective gloves, clothing, and eyewear when performing any maintenance operations to avoid personal injury.
D Disconnect any operating lines providing air pressure, electric power, or a control signal to the actuator. Be sure the actuator cannot suddenly open or close the valve.
D Use bypass valves or completely shut off the process to isolate the valve from process pressure. Relieve process pressure from both sides of the valve. Drain the process media from both sides of the valve.
D Vent the pneumatic actuator loading pressure and relieve any actuator spring precompression.
D Use lock‐out procedures to be sure that the above measures stay in effect while you work on the equipment.
D The valve packing box may contain process fluids that are pressurized, even when the valve has been removed from the pipeline . Process fluids may spray out under pressure when removing the packing hardware or packing rings, or when loosening the packing box pipe plug.
D Check with your process or safety engineer for any additional measures that must be taken to protect against process media.
CAUTION
Follow instructions carefully to avoid damaging the product surfaces, which could result in damage to the product.
Note
Whenever a gasket seal is disturbed by removing or shifting parts, a new gasket should be installed upon reassembly. This is necessary to ensure a good gasket seal since the used gasket may not seal properly.
Figure 2. Single PTFE V‐Ring Packing Arrangement
UPPER WIPER
(KEY 12)
PACKING
FOLLOWER
(KEY 13)
FEMALE
ADAPTER 1
PACKING RING 1
MALE
ADAPTER 1
WASHER
(KEY 10)
SPRING
(KEY 8)
PACKING BOX
RING (KEY 11)
12A7837‐A
A6745
LOWER WIPER 1
NOTE:
PACKING SET (KEY 6) CONTAINS A FEMALE ADAPTER, V-RING PACKING RINGS, MALE ADAPTER, AND LOWER WIPER RINGS.
5
EZ-C, ET-C, and EWT-C Valves
July 2017
Figure 3. Double PTFE V‐Ring Packing Arrangements
UPPER WIPER
(KEY 12)
PACKING
FOLLOWER (KEY 13)
FEMALE
ADAPTER 1
PACKING RING
MALE
ADAPTER 1
LANTERN RING
(KEY 8)
1
PACKING BOX
RING (KEY 11)
9.5 mm
(3/8 INCH)
STEM
12.7 mm
(1/2 INCH)
STEM
19.1, 25.4, OR 31.8 mm
(3/4, 1, OR 1‐1/4 INCH)
STEM
LOWER WIPER 1
NOTE:
PACKING SET (KEY 6) CONTAINS A FEMALE ADAPTER, V-RING PACKING RINGS, MALE ADAPTER, AND LOWER WIPER RINGS.
A6746
Figure 4. Graphite Ribbon/Filament Packing Arrangements
PACKING
FOLLOWER (KEY 13)
GRAPHITE RIBBON
PACKING RING
(KEY 7)
GRAPHITE FILAMENT
PACKING RING
(KEY 7)
LANTERN RING
(KEY 8)
PACKING BOX
RING (KEY 11)
9.5 mm
(3/8 INCH)
STEM
12.7 mm
(1/2 INCH)
STEM
19.1, 25.4, OR 31.8 mm
(3/4, 1, OR 1‐1/4 INCH)
STEM
NOTE:
0.102 mm (0.004 INCH) THICK SACRIFICIAL ZINC WASHERS: USE ONLY ONE BELOW EACH GRAPHITE RIBBON RING.
A6747
Instruction Manual
D102175X012
6
Instruction Manual
D102175X012
EZ-C, ET-C, and EWT-C Valves
July 2017
Packing Maintenance
Note
If the valve has ENVIRO‐SEAL live‐loaded packing installed, refer to the instruction manual ENVIRO‐SEAL Packing System for Sliding
Stem Valves for packing instructions. Figure 6 shows typical ENVIRO‐SEAL arrangements.
For spring‐loaded single PTFE V‐ring packing, the spring (key 8) maintains a sealing force on the packing. If leakage is noted around the packing follower (key 13), check to be sure the shoulder on the packing follower is touching the bonnet. If the shoulder is not touching the bonnet, tighten the packing flange nuts (key 5), until the shoulder is against the bonnet. If leakage cannot be stopped in this manner, proceed with replacing packing procedures.
If there is undesirable packing leakage with other than spring‐loaded packing, first try to limit the leakage and establish a stem seal by tightening the packing flange nuts.
If the packing is relatively new and tight on the stem, and if tightening the packing flange nuts does not stop the leakage, it is possible that the valve stem is worn or nicked so that a seal cannot be made. The surface finish of a new valve stem is critical for making a good packing seal. If the leakage comes from the outside diameter of the packing, it is possible that the leakage is caused by nicks or scratches around the packing box wall. If performing any of the following procedures, inspect the valve stem and packing box wall for nicks and scratches.
Replacing Packing
WARNING
Refer to the WARNING at the beginning of the Maintenance section in this instruction manual.
1. Isolate the control valve from the line pressure, release pressure from both sides of the valve body, and drain the process media from both sides of the valve. If using a power actuator, also shut off all pressure lines to the power actuator, and release all pressure from the actuator. Use lock‐out procedures to be sure that the above measures stay in effect while you work on the equipment. Observe the Warnings at the start of the Maintenance section.
2. Disconnect the operating lines from the actuator and any leak‐off piping from the bonnet. Disconnect the stem connector and remove the actuator from the valve by unscrewing the yoke locknut (key 15) or hex nuts (key 26, not shown).
3. Loosen the packing flange nuts (key 5) so that the packing is not tight on the valve stem. Remove any travel indicator parts and stem locknuts from the valve stem threads.
WARNING
D To avoid personal injury or property damage caused by uncontrolled movement of the bonnet, loosen the bonnet by following the instructions in the next steps.
7
EZ-C, ET-C, and EWT-C Valves
July 2017
Instruction Manual
D102175X012
Do not remove a stuck bonnet by pulling on it with equipment that can stretch or store energy in any other manner. The sudden release of stored energy can cause uncontrolled movement of the bonnet.
D To avoid personal injury or damage to the seating surface caused by the valve plug and stem assembly dropping from the bonnet after being lifted out of the valve body, observe the following instructions.
4. When lifting an EZ‐C bonnet, temporarily install a valve stem locknut on the valve stem. This locknut will prevent the valve plug and stem assembly from dropping out of the bonnet.
5. When lifting an ET‐C or EWT‐C bonnet, be sure the plug and stem assembly and cage remain in the valve body.
WARNING
To avoid possible personal injury, review your process shutdown procedures to be sure process pressure is not applied to the valve for the following procedure.
6. Hex nuts (key 16) attach the bonnet to the valve body (key 1). Loosen these nuts or cap screws approximately 3 mm
(1/8 inch). Then, loosen the body‐to‐bonnet joint by either rocking the bonnet or prying between the bonnet and valve body. Work with a prying tool around the bonnet until the bonnet loosens.
Table 3. Recommended Torque for Packing Flange Nuts
VALVE STEM DIAMETER mm
9.5
12.7
19.1
25.4
31.8
Inch
3/8
1/2
3/4
1
1‐1/4
PRESSURE
RATING
300
600
150
300
600
150
300
600
150
300
600
150
300
600
150
15
21
19
26
35
27
36
49
5
7
4
6
9
11
GRAPHITE PACKING
Minimum Torque
N S m Lbf‐in
3 27
Maximum Torque
N S
5 m Lbf‐in
40
36
49
44
59
81
99
6
8
8
10
14
17
53
73
66
88
122
149
133
182
169
226
310
238
318
437
23
31
29
38
53
40
54
74
199
274
254
339
466
357
477
655
7
10
9
12
17
13
17
24
2
3
4
5
2
3
PTFE PACKING
Minimum Torque
N S m Lbf‐in
1 13
Maximum Torque
N S m Lbf‐in
2 19
17
23
21
28
39
47
3
4
4
5
7
8
26
35
31
42
58
70
64
87
80
108
149
113
152
209
11
15
14
18
25
19
26
36
95
131
120
162
223
169
228
314
Table 4. Body‐to‐Bonnet Torque Guidelines
VALVE SIZE, NPS
BOLT TORQUES (1)
Bolt Material (2)
B8M (3) or S20910 (XM‐19) (4)
1
1-1/2 or 2
3
4, 6X4, or 8X4
N S m
122
91
163
258
6, 8X6, or 12X6
8 or 10X8
522
712
1.Determined from laboratory testing.
2. For bolting materials not listed in table 4, contact your
Emerson sales office or Local Business Partner for torque information.
3.SA193‐B8M strain hardened.
4.Hot rolled.
Lbf‐ft
90
67
120
190
385
525
8
Instruction Manual
D102175X012
EZ-C, ET-C, and EWT-C Valves
July 2017
D If fluid leaks from the joint, it may indicate that process pressure is applied to the valve. Review your process shutdown procedures, and be sure process pressure is not applied to the valve.
D If no fluid leaks from the joint, remove the nuts completely and carefully lift the bonnet off the valve body.
7. For EZ‐C valves, remove the stem locknut. Separate the valve plug and stem from the bonnet, and set the parts on a protective surface to prevent damage to gasket or seating surfaces.
8. For ET‐C and EWT‐C: If it is necessary to remove and inspect the valve trim, refer to the following Trim Maintenance section.
9. Remove the bonnet gasket (key 10) and cover the opening in the valve to protect the gasket surface and prevent foreign material from getting into the valve body cavity.
10. Remove the packing flange nuts, packing flange, upper wiper, and packing follower (keys 5, 3, 12, and 13).
Carefully push out all the remaining packing parts from the valve side of the bonnet using a rounded rod or other tool that will not scratch the packing box wall. Clean the packing box and metal packing parts.
11. Inspect the valve stem threads and packing box surfaces for any sharp edges which might cut the packing.
Scratches or burrs in the packing box surfaces could cause leakage or damage to the new packing. If the surface condition cannot be improved by light sanding, replace the damaged parts.
12. If necessary, go to the Trim Maintenance procedures to remove, inspect or replace trim parts. Return to this section when installing the bonnet on the valve body.
Installing the Bonnet
13. Remove the covering protecting the valve body cavity and install a new bonnet gasket (key 10), making sure the gasket seating surfaces are clean and smooth. Then slide the bonnet over the stem and onto the stud bolts (key 15).
Note
Proper performance of the bolting procedures in step 10 compresses the spiral wound gasket (key 12) or load ring (key 26) to both load and seal the seat ring gasket (key 13). It also compresses the outer edge of the bonnet gasket (key 10) to seal the body‐to‐bonnet joint.
The proper bolting procedures in step 14 include, but are not limited to, ensuring that bolting threads are clean and evenly tightening the cap screws or nuts onto the studs in a crisscross pattern. Tightening one cap screw or nut may loosen an adjacent cap screw or nut. Repeat the crisscross tightening pattern several times until each cap screw or nut is tight and the body‐to‐bonnet seal is made.
Note
Stud(s) and nut(s) should be installed such that the manufacturer's trademark and material grade marking is visible, allowing easy comparison to the materials selected and documented in the Emerson/Fisher serial card provided with this product.
WARNING
Personal injury or damage to equipment could occur if improper stud and nut materials or parts are used. Do not operate or assemble this product with stud(s) and nut(s) that are not approved by Emerson/Fisher engineering and/or listed on the serial card provided with this product. Use of unapproved materials and parts could lead to stresses exceeding the design or code limits intended for this particular service. Install studs with the material grade and manufacturer's identification mark visible. Contact your Emerson representative immediately if a discrepancy between actual parts and approved parts is suspected.
9
EZ-C, ET-C, and EWT-C Valves
July 2017
Instruction Manual
D102175X012
14. Lubricate the bolting with anti‐seize lubricant and install it, using accepted bolting procedures during tightening, so that the body‐to‐bonnet joint will withstand test pressures and application service conditions. Use the bolt
as guidelines.
Place a smooth‐edged pipe over the valve stem and gently tap each soft packing part into the packing box.
16. Slide the packing follower, upper wiper, and packing flange (keys 12, 13, and 3) into position. Lubricate the packing flange studs (key 4) and faces of the packing flange nuts (key 5). Install the packing flange nuts.
17. Tightening packing flange nuts (key 5): a. For spring‐loaded PTFE V‐ring packing, tighten the packing flange nuts until the shoulder on the packing follower
(key 13) contacts the bonnet.
b. For graphite packing,
tighten the packing flange nuts to the maximum recommended torque shown in table 3.
Then, loosen the packing flange nuts, and retighten them to the recommended minimum torque shown in
c. For double PTFE V‐ring packing, tighten the packing flange nuts alternately in small equal increments until one of
packing flange is level and at a 90 degree angle to the valve stem.
d. For ENVIRO‐SEAL live‐loaded packing, refer to the Fisher instruction manual titled: ENVIRO‐SEAL Packing System for Sliding‐Stem Valves.
18. Mount the actuator on the valve assembly and reconnect the actuator and valve stem according to the procedure in the appropriate actuator instruction manual.
Trim Maintenance
WARNING
Refer to the WARNING at the beginning of the Maintenance section in this instruction manual.
This procedure describes how the valve trim can be completely disassembled. When inspection or repairs are required, perform only those steps necessary to accomplish the task. Observe the Warning at the start of the Maintenance section.
Key number locations are shown in figures 8 and 9, unless otherwise noted.
EZ‐C Trim Disassembly
Key number locations are shown in figure 8, unless otherwise noted.
1. Remove the actuator and the bonnet according to steps 1 through 9 of the Replacing Packing procedures in the
Maintenance section.
WARNING
To avoid personal injury due to leaking fluids, avoid damaging gasket sealing surfaces.
The surface finish of the valve stem (key 7) is critical for making a good packing seal.
The seating surfaces of the valve plug (key 2) and seat ring (key 9) are critical for proper shutoff.
Protect these surfaces accordingly.
10
Instruction Manual
D102175X012
EZ-C, ET-C, and EWT-C Valves
July 2017
Figure 5. Fisher EZ‐C Valve Stem Torque and Pin Replacement
GROOVE PIN
(KEY 8)
D
VALVE STEM mm Inch
9.5
12.7
19.1
3/8
1/2
3/4
STEM TORQUE
N S m
40‐47
81‐115
237‐339
Lbf‐ft
25‐35
60‐85
175‐250
DRILL SIZE,
INCHES
3/32
1/8
3/16
D
DIMENSION mm Inch
16
19
25
0.625
0.75
1
35A5717‐C
Perform the following steps to remove the valve trim.
Note
come out of the valve body with the valve plug and stem assembly, and in other valve plug sizes and configurations, the valve plug will slide through the seat ring retainer and bushing assembly, leaving the retainer and bushing assembly in the valve body.
2. With the valve plug and stem assembly out of the valve body, either slide the seat ring retainer, bushing assembly
(keys 3 and 26), gaskets, and shim (keys 10, 12, and 25) up over the valve plug and stem or, lift the seat ring retainer and bushing assembly, associated gaskets, and shim out of the valve body. If the valve plug is to be reused, protect the valve plug seating surface to prevent damage.
3. To disassemble the stem, plug, and pin, drive or drill out the pin (key 8) and unscrew the valve stem (key 7) from the valve plug (key 2).
4. Remove the seat ring and seat ring gasket (keys 9 and 13).
5. Inspect parts for wear or damage that could prevent proper operation of the valve. Clean, inspect and obtain replacement parts as necessary for reassembly.
EZ‐C Trim Assembly
This procedure assumes that all the trim and associated gaskets were removed from the valve body. If these parts were not all removed, start the assembly procedure at the appropriate step.
CAUTION
To avoid weakening the stem that may cause failure in service, never reuse an old stem with a new valve plug. Using an old stem with a new plug requires drilling a new pin hole in the stem, which will weaken the stem. However, a used valve plug may be reused with a new stem.
Key number locations are shown in figure 8, unless otherwise noted.
11
EZ-C, ET-C, and EWT-C Valves
July 2017
Instruction Manual
D102175X012
or burrs and drive in a new pin (key 8) to lock the assembly.
2. Install the seat ring gasket (key 13) and seat ring (key 9).
Note
With some valve plug sizes and configurations, the valve plug will slide through the seat ring retainer and bushing assembly (keys
3 and 26), and in other configurations, it will not.
3. If the valve plug (key 2) will not slide through the seat ring retainer and bushing assembly (keys 3 and 26), proceed as follows: a. Place the seat ring retainer and bushing assembly (keys 3 and 26) over the stem of the valve plug and stem assembly.
b. Install the seat ring retainer and bushing assembly, which also includes the valve plug and stem assembly, on top of the seat ring, ensuring that the seat ring retainer slips onto the seat ring properly. Any rotational orientation of the seat ring retainer with respect to the valve body is acceptable.
Table 5. Fisher ET‐C and EWT‐C Valve Stem Torque and Pin Replacement mm
9.5
VALVE STEM DIAMETER
Inches
3/8
TORQUE, MINIMUM TO MAXIMUM
N S m Lbf‐ft
40‐47 25‐35
12.7
19.1
25.4
31.8
1/2
3/4
1
1‐1/4
81‐115
238‐339
421‐482
827‐908
60‐85
175‐250
310‐355
610‐670
DRILL SIZE, INCHES
3/32
1/8
3/16
1/4
1/4 c. Place the spiral wound gasket, shim, and bonnet gasket (keys 12, 25, and 10) on the shoulder of the seat ring retainer.
4. If the valve plug (key 2) will slide through the seat ring retainer and bushing assembly (keys 3 and 26), proceed as follows: a. Install the seat ring retainer and bushing assembly on top of the seat ring, ensuring that the seat ring retainer slips onto the seat ring properly. Any rotational orientation of the seat ring retainer with respect to the valve body is acceptable.
b. Place the spiral wound gasket, shim, and bonnet gasket (keys 12, 25, and 10) on the shoulder of the seat ring retainer.
c. Slide the valve plug and stem assembly or the valve plug guide and stem assembly into the seat ring retainer and bushing assembly (keys 3 and 26).
5. Mount the bonnet on the valve body and complete assembly using the Replacing Packing procedures in the
Maintenance section.
6. If the valve has soft metal‐to‐metal seats, refer to the Coining Soft Metal‐to‐Metal Seats section.
ET‐C and EWT‐C Trim Disassembly
Key number locations are shown in figure 9, unless otherwise noted.
12
Instruction Manual
D102175X012
EZ-C, ET-C, and EWT-C Valves
July 2017
1. Remove the actuator and the bonnet according to steps 1 through 9 of the Replacing Packing procedure in the
Maintenance section.
WARNING
To avoid personal injury due to leaking fluids, avoid damaging gasket sealing surfaces.
The surface finish of the valve stem (key 7) is critical for making a good packing seal.
The inside surface of the cage (key 3) is critical for tight shutoff and smooth operation of the valve plug.
The seating surfaces of the valve plug (key 2) and seat ring (key 9) are critical for proper shutoff.
Protect these surfaces accordingly.
Perform the following steps to remove the valve trim.
2. Remove the load ring (key 26) from an NPS 8 ET‐C or NPS 10X8 EWT‐C valve, and wrap it for protection.
3. Remove the plug and stem assembly from the valve body. The cage (key 3) might come out of the valve body with the plug, due to seal ring friction.
a. If so, carefully separate the cage from the plug and stem assembly.
b. If the cage was not removed from the valve body with the plug and stem assembly, remove it, the associated gaskets (keys 10 and 12), and shim (key 51).
4. Remove the seat ring (key 9) and seat ring gasket (key 13). Composition seat constructions use a disk (key 23) sandwiched between a disk seat (key 22) and disk retainer (key 21).
5. Clean, inspect, and if necessary obtain replacement parts.
ET‐C and EWT‐C Valve Plug Maintenance
CAUTION
To avoid the valve plug seal ring (key 28) not sealing properly and affecting valve performance, be careful not to scratch the surfaces of the ring groove on the valve plug or any of the surfaces of the replacement ring.
1. With the valve plug (key 2) removed, according to the disassembly portion of the Trim Maintenance procedure, proceed as follows:
2. The spring‐loaded seal ring may be removed by first working the retaining ring (key 27) off with a screwdriver. Then carefully slide the metal backup ring (key 29) and seal ring (key 28) off the valve plug (key 2).
3. A spring‐loaded seal ring must be installed so that its open side faces toward the valve stem, or toward the seat of
seal ring (key 28) onto the valve plug followed by the metal backup ring (key 29).
4. Then install the retaining ring (key 27) by inserting one end in the groove and, while turning the plug, press the ring into the groove. Again, be careful not to scratch any surfaces of the ring or plug.
CAUTION
To avoid weakening the stem that may cause failure in service, never reuse an old stem with a new valve plug. Using an old stem with a new plug requires drilling a new pin hole in the stem, which will weaken the stem. However, a used valve plug may be reused with a new stem.
13
EZ-C, ET-C, and EWT-C Valves
July 2017
Instruction Manual
D102175X012
5. To replace the valve stem (key 7), drive or drill out the pin (key 8). Unscrew the valve plug from the stem.
proper drill size. Drill through the stem using the hole in the valve plug as a guide. Remove any chips or burrs and drive in a new pin to lock the assembly.
ET‐C and EWT‐C Trim Assembly
Key number locations are shown in figure 9, unless otherwise noted.
1. Install the seat ring gasket (key 13), and seat ring (key 9) or disk seat (key 22). With composition seat constructions, install the disk (key 23) and disk retainer (key 21).
2. Install the cage (key 3). Any rotational orientation of the cage with respect to the valve body is acceptable.
3. Lower the valve plug (key 2) and stem assembly into the cage. Make sure the seal ring (key 28) is evenly engaged in the entrance chamfer at the top of the cage (key 3) to avoid damaging the ring.
4. Place the gaskets (keys 12 and 10) and the shim (key 51) on top of the cage.
5. With an NPS 8 ET‐C or NPS 10X8 EWT‐C valve, install the load ring (key 26).
6. Mount the bonnet on the valve body and complete assembly using the Replacing Packing procedures in the
Maintenance section. Torque guidelines for body‐to‐bonnet bolting are shown in table 4.
7. If the valve has soft metal‐to‐metal seats, refer to the Coining Soft Metal‐to‐Metal Seats section, below.
Coining Soft Metal‐to‐Metal Seats
Soft metal‐to‐metal seat constructions consist of a valve plug with hardfaced CoCr‐A seat and a non‐hardfaced S31600 seat ring. For optimum shutoff performance of these constructions, coin seats by stroking the valve plug into the seat ring at least three times with maximum actuator force.
CAUTION
To avoid possible product damage which may affect performance, do not lap soft metal‐to‐metal seats.
Parts Ordering
Each body‐bonnet assembly is assigned a serial number which can be found on the valve. This same number also appears on the actuator nameplate when the valve is shipped from the factory as part of a control valve assembly.
Refer to the serial number when contacting your Emerson sales office or Local Business Partner for technical assistance. When ordering replacement parts, refer to the serial number and to the eleven‐character part number for each part required from the following parts kit or parts list information.
WARNING
Use only genuine Fisher replacement parts. Components that are not supplied by Emerson Automation Solutions should not, under any circumstances, be used in any Fisher valve, because they may void your warranty, might adversely affect the performance of the valve, and could cause personal injury and property damage.
14
Instruction Manual
D102175X012
EZ-C, ET-C, and EWT-C Valves
July 2017
Parts Kits
Gasket Kits
Includes keys 10, 12, 13, and 25 for EZ‐C valves. Includes keys 10, 12, 13, and 51 for ET‐C and EWT‐C valves.
VALVE SIZE, NPS
1
1-1/2
2
3
4, 6X4, 8X4
6
8X6, 12X6
8, 10X8
KIT PART NUMBER
RGASKETX162
RGASKETX172
RGASKETX182
RGASKETX202
RGASKETX212
RGASKETX222
RGASKETX392
RGASKETX232
Packing Kits
Packing kits for standard packing includes keys 6, 8, 10, 11, and 12. Packing kits do not apply to N10276, N08020, or
N04400 trims.
Standard Packing Repair Kits (Non Live‐Loaded)
Stem Diameter, mm (Inches)
Yoke Boss Diameter, mm (Inches)
PTFE (Contains keys 6, 8, 10, 11, and 12)
Double PTFE (Contains keys 6, 8, 11, and 12)
Single Graphite Ribbon/Filament (Contains keys 7 [ribbon ring],
7 [filament ring], 8, and 11)
Single Graphite Ribbon/Filament (Contains keys 7 [ribbon ring],
7 [filament ring], and 11)
Single Graphite Ribbon/Filament (Contains keys 7 [ribbon ring],
7 [filament ring])
Double Graphite Ribbon/Filament (Contains keys 7 [ribbon ring],
7 [filament ring], 8, and 11)
9.5 (3/8)
54 (2‐1/8)
RPACKX00012
RPACKX00042
RPACKX00102
- - -
RPACKX00132
RPACKX00162
12.7 (1/2)
71 (2‐13/16)
RPACKX00022
RPACKX00052
RPACKX00112
- - -
RPACKX00142
RPACKX00172
19.1 (3/4)
90 (3‐9/16)
RPACKX00032
RPACKX00062
RPACKX00122
- - -
RPACKX00152
RPACKX00182
25.4 (1)
127 (5)
RPACKX00342
RPACKX00362
- - -
RPACKX00532
- - -
- - -
ENVIRO‐SEAL Packing Retrofit Kits
Retrofit kits include parts to convert valves with existing standard bonnets to the ENVIRO‐SEAL packing box
construction. Refer to figure 6 for key numbers for PTFE and Graphite ULF packing.
Stems and packing box constructions that do not meet Fisher stem finish specifications, dimensional tolerances, and design specifications, may adversely alter the performance of this packing kit.
ENVIRO‐SEAL Packing Retrofit Kits
PACKING
MATERIAL
Double PTFE
Graphite ULF
Duplex
9.5 (3/8)
54 (2‐1/8)
RPACKXRT012
RPACKXRT262
RPACKXRT212
STEM DIAMETER AND YOKE BOSS DIAMETER, mm (INCH)
12.7 (1/2)
71 (2‐13/16)
RPACKXRT022
19.1 (3/4)
90 (3‐9/16)
RPACKXRT032
RPACKXRT272
RPACKXRT222
RPACKXRT282
RPACKXRT232
25.4 (1)
127 (5)
RPACKXRT042
RPACKXRT292
RPACKXRT242
15
EZ-C, ET-C, and EWT-C Valves
July 2017
Instruction Manual
D102175X012
ENVIRO‐SEAL Packing Repair Kits
Repair kits include parts to replace the “soft” packing materials in valves that already have ENVIRO‐SEAL packing
numbers for PTFE and Graphite ULF packing.
Stems and packing box constructions that do not meet Fisher stem finish specifications, dimensional tolerances, and design specifications, may adversely alter the performance of this packing kit.
ENVIRO‐SEAL Packing Repair Kits
Stem Diameter, mm (Inches)
Yoke Boss Diameter, mm (Inches)
Double PTFE (Contains keys 214, 215, & 218)
Graphite ULF (Contains keys 207, 208, 209, 210, and 214)
Duplex (Contains keys 207, 209, 214, and 215)
9.5 (3/8)
54 (2‐1/8)
RPACKX00192
RPACKX00592
RPACKX00292
12.7 (1/2)
71 (2‐13/16)
RPACKX00202
RPACKX00602
RPACKX00302
19.1 (3/4)
90 (3‐9/16)
RPACKX00212
RPACKX00612
RPACKX00312
25.4 (1)
127 (5)
RPACKX00222
RPACKX00622
RPACKX00322
Figure 6. ENVIRO‐SEAL Packing System
APPLY LUBRICANT
A6362/G1
PTFE PACKING ARRANGEMENT
APPLY LUBRICANT
39B4612/A
GRAPHITE ULF PACKING ARRANGEMENT
16
Instruction Manual
D102175X012
Figure 7. Extension Bonnet Assembly
EZ-C, ET-C, and EWT-C Valves
July 2017
44B8565‐A
NOTE:
KEY 6 CONTAINS SEVERAL PARTS; REFER TO FIGURES 2, 3, AND 4 FOR PACKING ARRANGEMENTS.
Keys 6* and 7* Packing Box Parts
DESCRIPTION
KEY
NO.
9.5 (3/8)
STEM DIAMETER, mm (INCHES)
12.7 (1/2) 19.1 (3/4)
PTFE
V‐Ring
Packing
Packing Set, PTFE (1 req'd for single, 2 req'd for double) (1)
6 1R290001012 1R290201012 1R290401012
Graphite
Ribbon/F ilament
Packing
Graphite Ribbon Ring (2 req'd)
Graphite Filament Ring
Quantity Required
7
7
‐ ‐ ‐
1V3160X0022
1F3370X0322
2
1V3802X0022
1E3190X0222
2
1V2396X0022
1E3191X0282
3
1.Key 6 for double construction contains one extra packing ring for the 9.5 mm (3/8 inch) stem, and one extra lower wiper for all sizes. Discard upon assembly.
25.4 (1)
1R290601012
1U6768X0022
1D7518X0132
3
*Recommended spare parts 17
EZ-C, ET-C, and EWT-C Valves
July 2017
Instruction Manual
D102175X012
Parts List
Note
Part numbers are shown for recommended spares only. For part numbers not shown, contact your Emerson sales office or Local Business
Partner.
Bonnet Parts (figure 7)
Key Description Part Number
13
14
15
25
26
35
1 Bonnet
If you need a bonnet as a replacement part, order by
6*
7*
8
10
11
4
5
2
3 valve size and stem diameter, serial number, and desired material.
Bushing
Packing Flange
Packing Flange Stud
Packing Flange Nut
Single V‐Ring Packing Set
Individual Packing Ring
Packing Box Ring or Lantern Ring
Special Washer
Packing Box Ring
12* Upper Wiper, felt
9.5 mm (3/8 inch) stem
12.7 mm (1/2 inch) stem
19.1 mm (3/4 inch) stem
25.4 mm (1‐inch) stem
See following table
See following table
1J872606332
1J872706332
1J872806332
1J872906332
Packing Follower
Pipe Plug
Yoke Locknut
Cap Screw
Hex Nut
Retaining Ring
EZ‐C Valve Body Parts (figure 8)
Note
Part numbers are shown for recommended spares only. For part numbers not shown, contact your Emerson sales office or Local Business
Partner.
Key Description
1
2*
Valve Body
If you need a valve body as a replacement part, order by valve size, serial number, and desired material.
Valve Plug
Part Number
See following table
Key Description Part Number
3*
7*
8*
Seat Ring Retainer, CF8M (316 SST)
(Part numbers for Seat Ring Retainer/Bushing Assemblies are provided in a following table)
NPS 1
NPS 1-1/2
NPS 2
25A6683X022
25A6685X022
25A6687X022
NPS 3
NPS 4
Stem
Pin
9* Seat Ring
10* Bonnet Gasket, S31600/graphite
NPS 1
NPS 1-1/2
NPS 2
NPS 3
NPS 4
25A6689X022
35A6691X022
See following table
See following table
See following table
1R2859X0042
1R3101X0032
1R3299X0042
1R3484X0042
1R3724X0042
33
‐ ‐ ‐
34
55
12* Gasket, N06600/graphite
NPS 1
NPS 1-1/2
NPS 2
NPS 3
NPS 4
13* Seat Ring Gasket, S31600/graphite
NPS 1
NPS 1-1/2
NPS 2
1R286099442
1R309999442
1R329799442
1R348299442
1R372299442
15
16
18
NPS 3
NPS 4
Stud Bolt
Hex Nut
Flow Arrow
19 Drive Screw
25* Shim, S31600
NPS 1
NPS 1-1/2
NPS 2
1R2862X0062
1R3098X0052
1R3296X0042
1R3481X0052
1J5047X0062
16A1936X012
16A1937X012
16A1938X012
NPS 3
NPS 4
26* Bushing, R30006 (alloy 6)
(Part number for Seat Ring Retainer/Bushing Assemblies are provided in a following table)
16A1940X012
16A1941X012
NPS 1
NPS 1-1/2
NPS 2, restricted port
NPS 2, full port
NPS 3
NPS 4, restricted port
NPS 4, full port
Nameplate
Warning Plate
Wire
Lubricant, anti‐seize
(not included with valve)
15A6508X022
15A7511X022
15A6509X022
15A6510X022
15A7491X022
15A5712X022
15A6511X022
- - -
18 *Recommended spare parts
Instruction Manual
D102175X012
Figure 8. Fisher EZ‐C Valve Assembly
EZ-C, ET-C, and EWT-C Valves
July 2017
16A1943‐A
GASKET DETAIL
APPLY LUBRICANT
NOTE:
EZ-C KEY NUMBERS NOT SHOWN ARE: 18, 19, 33, AND 34.
44B8573‐B
19
EZ-C, ET-C, and EWT-C Valves
July 2017
Instruction Manual
D102175X012
Key 2* Fisher EZ‐C Equal Percentage (Including Micro‐Form), Linear, and Quick‐Opening Valve Plugs
VALVE STEM
CONNECTION
VALVE SIZE, NPS VALVE PLUG STYLE
PORT DIAMETER VALVE PLUG MATERIAL mm
6.4
9.5
Inch
0.25
0.375
mm
9.5
Inch
3/8
S31600 w/CoCr‐A (alloy 6)
Seat
15A6663X012
16A5713X012
S31600 w/CoCr‐A
Seat and Guide
15A6664X012
16A5711X012
Micro‐Form
12.7
19.1
9.5
12.7
0.5
0.75
0.375
0.5
12.7
1/2
15A6659X012
16A3337X012
16A5714X012
15A6661X012
15A6660X012
16A3339X012
16A5712X012
15A6662X012
1, 1-1/2 and 2
Quick Opening
19.1
0.75
9.5
12.7
3/8
1/2
16A3338X012
15A6516X012
15A6518X012
16A3340X012
15A6517X012
15A6519X012
1-1/2
2, 3, 4
3
4
Linear
Equal Percentage
Quick Opening
Linear
Equal Percentage
Quick Opening
Linear
Equal Percentage
Quick Opening
Linear
Equal Percentage
Quick Opening
Linear
Equal Percentage
25.4
38.1
50.8
76.2
101.6
1
1.5
2
3
4
1/2
3/4
1/2
3/4
1/2
3/4
1/2
3/4
1/2
3/4
1/2
3/4
1/2
3/4
1/2
3/8
1/2
1/2
3/4
1/2
3/4
3/8
1/2
3/8
1/2
3/8
1/2
3/8
12.7
19.1
12.7
19.1
12.7
19.1
12.7
19.1
12.7
19.1
12.7
19.1
12.7
19.1
12.7
9.5
12.7
12.7
19.1
12.7
19.1
9.5
12.7
9.5
12.7
9.5
12.7
9.5
15A6642X012
15A6644X012
15A6528X012
15A6530X012
15A6626X012
15A6628X012
15A6646X012
15A6648X012
15A6532X012
15A6534X012
15A6630X012
15A6632X012
15A6650X012
15A6652X012
15A6614X012
15A6616X012
15A6634X012
15A6636X012
15A6520X012
15A6522X012
15A6618X012
15A6620X012
15A6638X012
15A6640X012
15A6524X012
15A6526X012
15A6622X012
15A6624X012
15A6643X012
15A6645X012
15A6529X012
15A6531X012
15A6627X012
15A6629X012
15A6647X012
15A6649X012
15A6533X012
15A6535X012
15A6631X012
15A6633X012
15A6651X012
15A6653X012
15A6615X012
15A6617X012
15A6635X012
15A6637X012
15A6521X012
15A6523X012
15A6619X012
15A6621X012
15A6639X012
15A6641X012
15A6525X012
15A6527X012
15A6623X012
15A6625X012
Key 3*, 26* Fisher EZ‐C Seat Ring Retainer and Bushing Assembly
VALVE SIZE, NPS
1
1-1/2
2
Full Port
Restricted Port
3
4
Full Port
Restricted Port
PART NUMBER
25A6683X072
25A6685X082
25A6687X112
25A6687X132
25A6689X132
35A6691X082
- - -
20 *Recommended spare parts
Instruction Manual
D102175X012
EZ-C, ET-C, and EWT-C Valves
July 2017
Key 7* Fisher EZ‐C Valve Stem, S20910 (Use W/Group 1 Actuators)
VALVE SIZE, NPS
1 and 1-1/2
9.5 mm (3/8 Inch)
10A8823XM72
12.7 mm (1/2 Inch)
STEM DIAMETER
12.7 x 9.5 mm (1/2 x 3/8 Inch)
10A8840XBC2 11A2318X622
2
3
4
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
10A8840XBD2
10A8840XBE2
1U2307X0012
11A2318X632
‐ ‐ ‐
‐ ‐ ‐
19.1 mm (3/4 Inch)
‐ ‐ ‐
10B9265XBC2
10A9265XBD2
10A9265XBE2
Key 8* Fisher EZ‐C Pin, S31600
VALVE SIZE, NPS
1 and 1-1/2
2
3
VALVE PLUG STYLE
Micro‐Form, Linear, Equal Percentage and Quick
Opening
Linear, Equal Percentage and Quick Opening (full capacity)
Micro‐Form, Linear, Equal Percentage and Quick
Opening (restricted capacity)
All
Full Capacity
4
Restricted Capacity
VALVE STEM CONNECTION mm Inch
9.5
12.7
12.7
19.1
9.5
12.7
12.7
19.1
12.7
19.1
12.7
19.1
1/2
3/4
3/8
1/2
1/2
3/4
3/8
1/2
1/2
3/4
1/2
3/4
PART NUMBER
1B599335072
1D5423X00B2
1B599835072
1B813635072
1B599335072
1D5423X00B2
1B599835072
1B813635072
1B599835072
1B813635072
1B599335072
1F723635072
Key 9* Fisher EZ‐C Valve Seat Ring, S31600
VALVE
SIZE,
NPS
1
PORT DIAMETER
6.4 mm
(0.25 Inch)
9.5 mm
(0.375 Inch)
12.7 mm
(0.5 Inch)
19.1 mm
(0.75 Inch)
25.1 mm
(1 Inch)
24B7585X012 24B8298X012 24B8299X012 24B8300X012 24B8301X012
38.1 mm
(1.5 Inch)
‐ ‐ ‐
1-1/2 24B6344X012 24B7586X012 24B7213X012 24B7214X012 24B7215X012 24B7216X012
2 24B8555X012 24B8556X012 24B8557X012 24B8558X012 24B8559X012 ‐ ‐ ‐
3
4
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
50.8 mm
(2 Inch)
‐ ‐ ‐
‐ ‐ ‐
24B8560X012
76.2 mm
(3 Inch)
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
24B8561X012 24B8562X012
24B8510X012 ‐ ‐ ‐
101.6 mm
(4 Inch)
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
24B8563X012
*Recommended spare parts 21
EZ-C, ET-C, and EWT-C Valves
July 2017
ET‐C and EWT‐C Valve Body Parts (figure 9)
Note
Part numbers are shown for recommended spares only. For part numbers not shown, contact your Emerson sales office or Local Business
Partner.
Key Description Part Number
1
2*
3*
7*
8*
9*
Valve Body
If you need a valve body as a replacement part, order by valve size, serial number, and desired material.
See following table Valve Plug
Cage, CF8M (316 SST)/Chrome coat
Equal Percentage
NPS 3
NPS 4, 6X4, 8X4
NPS 6, 8X6, 12X6
NPS 8, 10X8
Linear
NPS 3
NPS 4, 6X4, 8X4
39B0341X012
39B0343X012
39B0345X012
39B0347X012
39B0342X012
39B0344X012
NPS 6, 8X6, 12X6
NPS 8, 10X8
Stem
Pin, S31600
9.5 mm (3/8 inch) stem
39B0346X012
39B0348X012
See following table
1V322635072
12.7 mm (1/2 inch) stem
19.1 mm (3/4 inch) stem
25.4 mm (1‐inch), & 38.1 mm (1‐1/4 inch) stem 1V334035072
Seat Ring,w/metal seat, 316 SST
ET‐C
1V322735072
1V326035072
NPS 3
NPS 4
NPS 6
NPS 8
EWT‐C
NPS 6X4
NPS 8X4
NPS 8X6
NPS 12X6
NPS 10X8
23B6127X032
23B6128X052
29A9703X072
29A9704X042
23B6129X042
23B6130X022
20B0811X042
33B6131X022
29A9704X042
10* Bonnet Gasket, S31600/graphite
NPS 3
NPS 4, 6X4, 8X4
NPS 6, 8X6, 12X6
NPS 8, 10X8
1R3484X0042
1R3724X0042
1U5081X0052
10A3265X112
Instruction Manual
D102175X012
Key Description
12* Spiral Gasket, N06600/graphite
NPS 3
NPS 4, 6X4, 8X4
NPS 6, 8X6, 12X6
13* Seat Ring Gasket
NPS 3, S31600/graphite
NPS 4, 6X4, 8X4, S31600/graphite
NPS 6, S31600/graphite
NPS 8X6, 12X6, N06600/graphite
NPS 8, 10X8, S31600/graphite
15
16
18
19
Stud Bolt
Hex Nut
Flow Arrow
Drive Screw
21* Disk Retainer, w/Composition Seat, 316 SST
NPS 3
NPS 4, 6X4, 8X4
NPS 6
NPS 8, 10X8
22* Disk Seat, w/Composition Seat, 316 SST
ET‐C
NPS 3
NPS 4
NPS 6
NPS 8
EWT‐C
NPS 6X4
NPS 8X4
NPS 8X6
NPS 12X6
NPS 10X8
23* Disk, PCTFE
NPS 3
NPS 4, 6X4, 8X4
NPS 6, 8X6, 12X6
NPS 8, 10X8
26
27
Load Ring
Retaining Ring
28* Seal Ring, R30003/UHMWPE
NPS 3
NPS 4, 6X4, 8X4
NPS 6, 8X6, 12X6
NPS 8, 10X8
29 Back‐Up Ring
51* Shim, S31600
NPS 3
53
55
NPS 4, 6x4, 8x4
NPS 6, 8X6, 12X6
Nameplate
Lubricant, anti‐seize
(not included with valve)
Part Number
1R348299442
1R372299442
1U508599442
1R3481X0052
1J5047X0062
1U5086X0032
1V644199442
10A3266X082
14B8251X012
14B8252X012
14B8254X012
14B8255X012
16A1940X012
16A1941X012
16A1942X012
- - -
1V711235072
1V711533092
1V711833092
10A4466X012
1V711435072
1V711733092
1V712033092
20A4467X012
1V712533092
1V712633092
2V721733092
2V712733092
20A4467X012
18A8539X012
18A0732X012
18A0733X012
20A4468X042
22 *Recommended spare parts
Instruction Manual
D102175X012
Figure 9. Fisher ET‐C and EWT‐C Valve Assembly
54B8568‐C
WHISPER TRIM
STD TRIM
CAVITROL TRIM
FLOW DIRECTION
EZ-C, ET-C, and EWT-C Valves
July 2017
54B8568‐C
FLOW UP FLOW DOWN
VIEW A
16A1943‐A
ALL CONSTRUCTIONS EXCEPT
NPS 8 AND 10X8
METAL SEAT
54B8568‐C
COMPOSITION SEAT
54B8579‐B
FOR NPS 8 AND 10X8
CONSTRUCTIONS
VIEW B
23
EZ-C, ET-C, and EWT-C Valves
July 2017
Instruction Manual
D102175X012
Key 2* Fisher ET‐C and EWT‐C Valve Plug
VALVE SIZE,
NPS
3
PORT DIAMETER
Inches
3.4375
mm
87.3
SEAT STYLE
Metal
S31600 w/CoCr‐A Seat
12.7 mm (1/2 Inch)
Stem
34B8275X012
19.1 mm (3/4 Inch)
Stem
34B8190X012
Composition
S31600 Seat
12.7 mm (1/2 Inch)
Stem
34B8288X012
19.1 mm (3/4 Inch)
Stem
34B8289X012
4, 6X4, 8X4 4.375
111
6, 8X6, 12X6
8, 10X8
7
8
178
203
34B8276X012
19.1 mm (3/4 Inch)
Stem
34B8278X012
34B8280X012
34B7639X012
25.4 mm (1‐Inch)
Stem
34B8279X012
34B8281X012
34B8290X012
19.1 mm (3/4 Inch)
Stem
34B8292X012
34B8294X012
34B8291X012
25.4 mm (1‐Inch)
Stem
34B8293X012
34B8296X012
Key 7* Fisher ET‐C and EWT‐C Valve Stem, S20910
STEM DIAMETER
VALVE SIZE, NPS mm
3
4, 6X4, 8X4
6, 8X6,
12X6
8, 10X8
12.7
19.1
12.7
19.1
19.1
25.4
25.4
19.1
25.4
Inches
1/2
3/4
1/2
3/4
3/4
1
1
3/4
1
ACTUATOR GROUP
1
1
1
1
1
100
101
1
100, 101
S20910
(XM‐19)
10A8840XBD2
10A9265XBF2
10A8840XAD2
10A9265XBG2
10A9265XBH2
11A3429XR72
11A3429XR62
10A9265XBJ2
11A3429XR82
*Recommended spare parts
Neither Emerson, Emerson Automation Solutions, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.
Fisher and ENVIRO-SEAL are marks owned by one of the companies in the Emerson Automation Solutions business unit of Emerson Electric Co. Emerson
Automation Solutions, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such products at any time without notice.
Emerson Automation Solutions
Marshalltown, Iowa 50158 USA
Sorocaba, 18087 Brazil
Cernay 68700 France
Dubai, United Arab Emirates
Singapore 128461 Singapore www.Fisher.com
24
1995, 2017 Fisher Controls International LLC. All rights reserved.
advertisement
Related manuals
advertisement