Naxa NCV-573 Instruction manual

Nada
THE NEW GENERATION IN TECHNOLOGY
NCV-573
7” TFT LCD HEADREST MONITOR
INSTRUCTION MANUAL
MADE IN CHINA
Congratulations for purchasing our video mobile multimedia
product.Before connecting,operating or adiusting this
product,please read these instructions completely to get the
best result from your multimedia products.
1.Do not repair it by yourself,if any trouble occurs please
immediately shut it off and contact our company or local
retailer. This monitor 1s composed of many precise electronic
components any attachment or reassembling may result
damages to the set.
2.Do not expose the monitor to humid air,dust,vapor,sunlight,
etc.
3.Do not use thinner or any other chemical cleaner.please
choose soft cloth to clean the dirt on the monitor.
4 Keep the monitor far from extremely heat or cool place
storage temperature:-25-+60°C
operating temperature:-10-+50°C
5.Prevent the set from falling or struck
Caution
To ensure security,please do not operate the monitor while
driving.
Page 1
CONTROL AND LAYOUT
Monitor
(1)Adjust Increase
(2)Menu( Press and hold 3 seconds for mute)
(3)Adjust Decrease
(4)Power on/off(Press and hold for turning
off / press once to change the mode)
(5)Remote sensor
(6)Video in 2
(7)Audio out(earplug)
(8) Infrared Transmitter (optional)
Remote control
(1) Volume Reducing Button
(2) Menu Button
(3) Power Button
(4) Video Select(16:9/4:3)
(5) Volume Increasing Button
(6) Switching AV1/ AV2
Page 2
H ©
у
es à
Ay Ey >) |
O O
INSTALLATION
SA YELLOW VIDEO IN(1)
— WHITE AUDIO IN
FUSE F— Red wire Power 12V
7 BOX —— BLACK WIRE GND
o J
o El
REMOTE CONTROL REPLACING BATTERIES
Pull out 4 N
Push
1.Always use new batteries when replacing the old set.
2.Do not attempt to charge,short-circuit,disassemble,
or burn used batteries.
3.Battery replacement is necessary when remote control
acts sporadically or stops operating.
4 Do not drop,apply shock or step on the remote control.
5.Do not spill water on the remote control.
6.Do not place objects between the remote control and
remote sensor.
7.Do not use remote control for other equipments at the
same time.
8.1f the monitor does not operate even when operating
the remote control from a close range, it is time to
replace the batteries, refer to the label on the back of
the basic control.
Page 3
OPERATING INSTRUCTIONS
1.Press MENU button to select bringhtness,contrast,
color volume, MODE, TCON (Rotate) , language, and reset control.
Press + or - to adjust selected feature.
-Brightness,contrast,color:adjust level to get most
suitable effect
-Volume:increase or decrease volume level
— Press MODE Button to select different display scale (16:9>4:3).
- “Zeou :to rotate image up/down,left/right
-Language:to change to different OSD language
-Reset:to reset all settings to default
TECHNICAL PARAMETERS
LCD Drive Method: TFT Active Matrix
Display Size: 7 Inch(diagonal)
Aspect:16: 9
Display Format: 180 XRGB X234
Number of Pixels:1440 X234
Video System Input:PAL/NTSC
Back Light:High Brightness
Power Source:DC 12V
Power Consumption:8W
Dimensions: 126X186 X24mm
SUPPLIED ACCESSORIES
Wire cord 1
Stand 1
Remote control 1
Headrest bracket 1
Key 2
Page 4
Bracket 1
For mounting stand purpose
Mounting Stand Key-for release the monitor from
headrest frame
Headrest Shroud
Page 5
Remove the bracket 2 from the
monitor and install bracket 1 as ñ
follows diagrams for stand style use -
Bracket 1
(7 >
[ |
|
\ 2)
Use Bracket 1 for stand style
INSTALLING HEADREST FRAME
Getting started
1.Remove the headrest and set1t in
an uncluttered work area. Take
the appropriate precautions to
ensure than it is not damaged
during installation.
Measurements
2.Push on the headliner with your
IB fingers to make sure there are no
obstructions that would hinder the
installation.Use the paper
template to mark the area to be cut.
Page 6
Cut the headrest
3.Using an adjustable-depth blade,
start your cut 1/4 inch inside one
corner and cut diagonally across,
Y stopping 1/4 inch in from the other
corner.Repeat the procedure for
the other two corners.
Remove form & obstructions
4.Carefully peel back the materials.
Set the adjustable blade to one
inch depth and cut around the
edges of the hole, staying 1/4inch
inside the edge.Pull up one corner
of the foam and use the blade to
cut underneath.Remove small
section at a time,using the pull up
and cut method for uniform depth.
Use a dremel or other appropriate
tool to remove other obstructions.
Insert the monitor to measure the
fit and make adjustments if
necessary.
Route the cable through the
headrest
5.Run the supplied cable through
the opening and out the bottom
of the headrest.If possible,
conceal the wires using a shft
covering.Connect the power,
ground and video leads to test the
monitor.Before connecting the
monitor,pull the connecting cable
assembly through the headrest
frame as shown in diagram.Place
headrest frame into the opening
and secure with correct faseners.
Page 7
Install the headrest shroud
6.Pull the connecting cable
through the center of the frame as
shown indiagram,then secure with
correct fasteners
Insert the monitor
7.Push to insert the monitor
into the headrest shroud
a Detachable
8.Insert the key between one side of the
monitor and headrest frame gap
and pull out to remove the
monitor from the headrest
shroud
Page 8