Advertisement
Advertisement
DIGITAL VIDEO
DVD VIDEO PLAYER & VIDEO
CASSETTE RECORDER
SD-V396SU
OWNER’S MANUAL
Introduction
2
Connections
14
Basic setup
22
Playback
(VCR)
29
Recording
(VCR)
34
Other functions
(VCR)
39
Basic playback
(DVD)
42
Advanced playback
(DVD)
45
Function setup
(DVD)
55
Others
67
©2004 Toshiba Corporation
This device does not tape-record copy protected DVD Video Discs.
2C53601A (E)COV 1 3/10/04, 11:30
Introduction
IMPORTANT SAFEGUARDS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not expose this appliance to rain or moisture.
CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN
BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by the partly responsible for compliance with the
FCC Rules could void the user's authority to operate this equipment.
CAUTION: THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.
TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS USER'S GUIDE CARE-
FULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTE-
NANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE.
USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLO-
SURE. VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED.
DO NOT STARE INTO BEAM.
Location of the required Marking
The rating sheet and the safety caution are on the rear of the unit.
CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCE
STANDARDS, 21 CFR SUBCHAPTER J.
2
2C53601A (E)p02-13 2 3/10/04, 11:30
IMPORTANT SAFEGUARDS
1. READ INSTRUCTIONS
All the safety and operating instructions should be read before the unit is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for future reference.
3. HEED WARNINGS
All warnings on the unit and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning the exterior cabinet only.
6. ATTACHMENTS
The manufacturer of this unit does not make any recommendations for attachments, as they may cause hazards.
7. WATER AND MOISTURE
Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.
8. ACCESSORIES
PORTABLE CART WARNING
(symbol provided by RETAC)
Do not place this unit on an unstable cart, stand, tripod, bracket, or table.
The unit may fall, causing serious injury, and serious damage to the unit.
8A.
An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
9. VENTILATION
Slots and openings in the cabinet back or bottom are provided for ventilation,
S3125A to ensure reliable operation of the unit, and to protect it from overheating.
These openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and/or the manufacturer’s instructions have been adhered to.
10. POWER SOURCE
This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For units intended to operate from battery power, or other sources, refer to the operating instructions.
11. GROUNDING OR POLARIZATION
This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Instead of the polarized alternating-current line plug, your unit may be equipped with a 3-wire grounding-type plug (a plug having a third (grounding) pin). This plug will only fit into a grounding-type power outlet. This too, is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet.Do not defeat the safety purpose of the grounding-type plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
3
2C53601A (E)p02-13 3 3/10/04, 11:30
Introduction
IMPORTANT SAFEGUARDS
13. LIGHTNING
To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges.
14. POWER LINES
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the
National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
18. SERVICING
Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
For example: a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation.
e. If the unit has been dropped or the cabinet has been damaged.
f . When the unit exhibits a distinct change in performance, this indicates a need for service.
19. REPLACEMENT PARTS
When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
20. SAFETY CHECK
Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition.
21. HEAT
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
22. DISC TRAY
Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.
23. CONNECTING
When you connect the product to other equipment, turn off the power and unplug all of the equipment from the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's manual of the other equipment carefully and follow the instructions when making any connections.
4
2C53601A (E)p02-13 4 3/10/04, 11:30
IMPORTANT SAFEGUARDS
/ Power source
24. LASER BEAM
Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the laser beam. It may cause sight damage.
25. DISC
Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury and product malfunction.
26. NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
EXAMPLE OF ANTENNA GROUNDING AS PER THE
NATIONAL ELECTRICAL CODE
ANTENNA LEAD IN WIRE
GROUND CLAMP
ELECTRIC SERVICE
EQUIPMENT
NEC-NATIONAL ELECTRICAL CODE
S2898A
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
Power source
Wider Hole and Blade
AC Outlet
Polarized AC Cord Plug
(One blade is wider than the other.)
TO USE AC POWER SOURCE
Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug into a standard 120V 60Hz polarized AC outlet.
Notes:
• Never connect the AC line cord plug to other than the specified voltage (120V 60Hz). Use the attached power cord only.
• If the polarized AC cord does not fit into a non-polarized AC outlet, do not attempt to file or cut the blade. It is the user’s responsibility to have an electrician replace the obsolete outlet.
• If you cause a static discharge when touching the unit and the unit fails to function, simply unplug the unit from the AC outlet and plug it back in. The unit should return to normal operation.
5
2C53601A (E)p02-13 5 3/10/04, 11:30
Introduction
Precautions
Notes on handling
When shipping the DVD/VCR, the original shipping carton and packing materials come in handy. For maximum protection, repack the unit as it was originally packed at the factory.
Do not use volatile liquids, such as insect spray, near the DVD/VCR. Do not leave rubber or plastic products to contact the DVD/VCR for a prolonged period. They will leave marks on the finish.
The top and rear panels of the DVD/VCR may become warm after a long period of use. This is not a malfunction.
When the DVD/VCR is not in use, be sure to remove the disc and the video cassette turn off the power.
If you do not use the DVD/VCR for a long period, the unit may not function properly in the future. Turn on and use the DVD/VCR occasionally.
Notes on moisture condensation
Moisture condensation damages the DVD/VCR.
Please read the following carefully.
Moisture condensation occurs, for example, when you pour a cold drink into a glass on a warm day. Drops of water form on the outside of the glass. In the same way, moisture may condense on the head drum or the optical pick-up lens inside this unit, one of the most crucial internal parts of the DVD/VCR.
Exam ple of moisture condensation!
Tape
Head drum
Notes on locating
Place the DVD/VCR on a level surface. Do not use it on a shaky or unstable surface such as a wobbling table or inclined stand. The loaded disc or the video tape may become dis-aligned and damage the DVD/
VCR.
When you place this DVD/VCR near a TV, radio, or
VCR, the playback picture may become poor and the sound may be distorted. In this case, place the DVD/
VCR away from the TV, radio, or VCR.
Moisture condensation occurs during the following cases.
When you bring the DVD/VCR directly from a cold place to a warm place.
When you use the DVD/VCR in a room where you just turned on the heater, or a place where the cold wind from the air conditioner directly hits the unit.
In summer, when you use the DVD/VCR in a hot and humid place just after you move the unit from an air conditioned room.
When you use the DVD/VCR in a humid place.
It’s too warm!
Notes on cleaning
Use a soft, dry cloth for cleaning.
For stubborn dirt, soak the cloth in a weak detergent solution, wring well and wipe. Use a dry cloth to wipe it dry.
Do not use any type of solvent, such as thinner and benzine, as they may damage the surface of the
DVD/VCR.
If you use a chemical saturated cloth to clean the unit, follow that product’s instructions.
To obtain a clear picture
The DVD/VCR is a high technology, precision device. If the video head, the head drum, the optical pick-up lens or disc drive parts are dirty or worn down, the picture quality will deteriorate. To obtain a clear picture, we recommend regular inspection and maintenance
(cleaning or parts replacement) every 1,000 hours of use depending on the operating environment. For details, contact your nearest dealer.
Do not use the DVD/VCR when moisture condensation may occur.
If you use the DVD/VCR in such a situation, it may damage discs and internal parts. Remove the disc or the video tape, connect the power cord of the DVD/
VCR to the wall outlet, turn on the DVD/VCR, and leave it for two or three hours. After two or three hours, the DVD/VCR will have warmed up and evaporated any moisture. Keep the DVD/VCR connected to the wall outlet and moisture condensation will seldom occur.
Wait!
Wall outlet
6
2C53601A (E)p02-13 6 3/10/04, 11:30
Notes on discs
On handling discs
Do not touch the playback side of the disc.
Structure of disc contents
Normally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. VIDEO CDs and audio CDs are divided into tracks.
DVD video disc
Title 1
Chapter 1 Chapter 2
DVD video disc
Title 2
Chapter 1 Chapter 2 Chapter 3
Do not attach paper or tape to discs.
Playback side
Video CD/Audio CD
Video CD/Audio CD
Track 1 Track 2 Track 3 Track 4 Track 5
On cleaning discs
Fingerprints and dust on the disc cause picture and sound deterioration. Wipe the disc from the center outwards with a soft cloth. Always keep the disc clean.
Each title, chapter or track is assigned a number, which is called “title number”, “chapter number” or “track number” respectively.
There may be discs that do not have these numbers.
If you cannot wipe off the dust with a soft cloth, wipe the disc lightly with a slightly moistened soft cloth and finish with a dry cloth.
Do not use any type of solvent such as thinner, benzine, commercially available cleaners or antistatic spray for vinyl LPs. It may damage the disc.
On storing discs
Do not store discs in a place subject to direct sunlight or near heat sources.
Do not store discs in places subject to moisture and dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing objects on discs outside of their case may cause warping.
Notes on copyright
It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, and rent copyrighted material without permission.
This device does not tape-record copy protected DVD
Video Discs.
The device is not to be used for copying copyrighted content without the express written permission of the copyright owner.
Obtaining such permission is the sole responsibility of the user.
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
7
2C53601A (E)p02-13 7 3/10/04, 11:30
Introduction
Notes on discs (continued)
About this owner’s manual
This owner’s manual explains the basic instructions of this DVD/VCR. Some DVD video discs are produced in a manner that allows specific or limited operation during playback. As such, the DVD/VCR may not respond to all operating commands. This is not a defect in the DVD/
VCR. Refer to instruction notes of discs.
“ ” may appear on the TV screen during operation.
A “ ” means that the operation is not permitted by the
DVD/VCR or the disc.
For example, sometimes it is unable to stop the playback of copyright message of the disc when the
STOP ( 3 ) button is pressed. Alternatively, the “ ” may also indicate that the feature is not available for the disc.
Playable discs
This DVD/VCR can play the following discs.
Disc Mark Contents
Disc
Size
Maximum playback time
Approx. 4 hours
(single sided disc)
12 cm
DVD video discs
Audio
+
Video
(moving pictures)
Approx. 8 hours
(double sided disc)
Approx. 80 minutes
(single sided disc)
8 cm
Approx. 160 minutes
(double sided disc)
Notes on region numbers
The region number of this DVD/VCR is 1. If region numbers, which stand for their playable area, are printed on your DVD video disc and you do not find 1 or
ALL
, disc playback will not be allowed by the player. (In this case, the DVD/VCR will display a message on-screen.)
Video
CDs
DIGITAL VIDEO
Audio
+
Video
(moving pictures)
12 cm Approx. 74 minutes
8 cm Approx. 20 minutes
On Video CDs
This DVD/VCR supports Video CDs equipped with the
PBC (Version 2.0) function. (PBC is the abbreviation of
Playback Control.) You can enjoy two playback variations depending on types of discs.
• Video CD not equipped with PBC function
(Version 1.1)
Sound and movie can be played on this DVD/VCR in the same way as an audio CD.
• Video CD equipped with PBC function
(Version 2.0)
In addition to operation of a Video CD not equipped with the PBC function, you can enjoy playback of interactive software with search function by using the menu displayed on the TV screen (Menu Playback).
Some of the functions described in this owner’s manual may not work with some discs.
12 cm Approx. 74 minutes
Audio
CDs
Audio
8 cm
(CD single)
Approx. 20 minutes
The following discs are also available.
DVD-R/RW discs of DVD video format
CD-R/CD-RW discs of CD-DA, Video CD, SVCD,
MP3, WMA or JPEG format
Kodak Picture CD and FUJICOLOR CD format
Some of these discs may be incompatible.
• You cannot play discs other than those listed above.
• You cannot play discs of DVD-RAM, DVD-ROM,
Photo CD, etc., or non standardized discs even if they may be labeled as above.
• Some CD-R/RWs can not be played back depending on the recording conditions.
• This DVD/VCR uses the NTSC color system, and cannot play DVD video discs recorded in any other color system (PAL, SECAM, etc.).
8
2C53601A (E)p02-13 8 3/10/04, 11:30
Contents
Introduction
IMPORTANT SAFEGUARDS .......................... 2
Power source ................................................... 5
Precautions ...................................................... 6
Notes on discs .................................................. 7
Contents. .......................................................... 9
Identification of controls ................................. 10
Connections
Antenna connections ...................................... 14
CATV (CABLE TV) connections ..................... 16
Connecting to a TV ........................................ 18
Connecting to optional equipment .................. 20
Basic setup
Setting the video channel ............................... 22
Setting the language ...................................... 23
Clock setting ................................................... 24
Tuner setting .................................................. 27
Playback (VCR)
Loading and unloading a cassette tape ......... 29
Cassette tape playback .................................. 30
Special playback ............................................ 31
Convenience function ..................................... 32
Recording (VCR)
Recording a TV program ................................ 34
One-touch Timer Recording (OTR) ................ 36
Timer recording .............................................. 37
Basic playback (DVD)
Playing a disc ................................................. 42
Advanced playback (DVD)
MP3/WMA/JPEG playback ............................ 45
Zooming ......................................................... 50
Locating desired scene .................................. 50
Marking desired scenes ................................. 51
Repeat playback ............................................ 52
A-B Repeat playback ..................................... 52
Program playback (CD) .................................. 53
Random playback (CD) .................................. 53
Changing angles ............................................ 54
Title selection ................................................. 54
DVD menu ...................................................... 54
Function setup (DVD)
Changing soundtrack language ..................... 55
Setting surround sound .................................. 55
Setting subtitles .............................................. 56
Karaoke playback ........................................... 56
E.B.L. (Enhanced Black Level) ...................... 57
Setting the aspect ratio of TV screen ............. 58
Setting on screen display ............................... 59
Status display of disc ..................................... 59
Dynamic Range Control ................................. 60
Parental control setting .................................. 61
To change the parental level .......................... 62
Temporary disabling of rating level by DVD disc .. 63
Setting OSD language ................................... 64
Setting language ............................................ 65
Selecting PROGRESSIVE scan ..................... 66
Other functions (VCR)
Stereo recording and playback ...................... 39
Second Audio Program (SAP) ........................ 39
Duplicating a video tape ................................. 40
Recording a DVD/CD disc .............................. 41
Others
Language code list ......................................... 67
Troubleshooting ............................................. 68
Specifications ................................................. 69
Limited warranty ............................................. 70
3/10/04, 11:30
9
2C53601A (E)p02-13 9
Introduction
Identification of controls
See the page in for details.
Front panel
VCR/DVD mode selector button 22
EJECT button 29
Cassette loading slot 29
DVD indicator
VCR indicator 22
42 OPEN/CLOSE button
Disc tray 42
42
ON/STANDBY button 22
AUDIO (L/R)/VIDEO IN
(LINE IN 2) jacks 40
REC button 34 Remote sensor 13
Display window 11
CHANNEL
M
/
?
buttons 34
STOP button 30
PLAY button 30
FF (Fast Forward) button
30
REW (Rewind) button 30
Rear panel
When connecting the optical digital cable, remove the cap and fit the connector into the jack firmly.
When not using the jack, keep the cap inserted to protect it from dust intrusion.
DVD OPTICAL DIGITAL AUDIO
OUT jack (dust protection cap) 20
DVD COAXIAL DIGITAL
AUDIO OUT jack 20
DVD/VCR common AUDIO
(L/R)/VIDEO OUT jacks 18
RF IN jack 14
10
DVD S-VIDEO
OUT jack 19
S-VIDEO/COMPONENT
Video selector switch 19
DVD AUDIO (L/R)
OUT jacks
19
DVD COMPONENT
OUT jacks 19
AC power cord 5
2C53601A (E)p02-13 10
AUDIO (L/R)/VIDEO
IN (LINE IN1) jacks 40
RF OUT jack 14
3/10/04, 11:31
Display window
Play indicator
VCR indicator (VCR) Still indicator Disc inserted indicator (DVD)
Recording indicator (VCR)
Disc inserted indicator (CD)
AM/PM indicator
(AM is not displayed)
Track indicator (CD) Multifunctional indicator
Tape loaded indicator (VCR) Progressive indicator
Timer Recording indicator (VCR)
VCR operation status
Press CALL to display information on screen.
To cancel the display, press CALL again.
While watching TV
DAY OF THE WEEK
CLOCK
8 : 47 AM MON
STEREO SAP
CH 125 CHANNEL
STEREO AND
SECOND
AUDIO
PROGRAM
(SAP)
00 : 00 : 00 SP TAPE SPEED
While operating a tape
HI-FI STEREO
8 : 30 AM MON
HI-FI
STEREO 00 : 15 : 12 SP
VCR Icons
Recording :
OPERATING
MODE
AUTO REPEAT
TAPE IN
Rec/Pause :
Play :
Stop :
Eject :
REAL TIME COUNTER OUTPUT SELECTION
DVD/CD/VCD operation status
Each press of DISPLAY , the status display of the disc will appear on the screen and change as follows.
DVD
DISC OPERATION
TITLE NO.
ELAPSED
TIME
00:34:56 01:12:33
TOTAL
TIME
Title
1/8
1/32
1/99
00:34:56 01:12:33
Chapter 1/999
Eng DolbyDigital
1/9
Eng
ANGLE NO.
CHAPTER NO.
A KIND OF AUDIO
AUDIO LANGUAGE
SUBTITLE LANGUAGE
DISC
OPERATION
TRACK NO.
CD/VCD
Track 11/99
34:56 71:33
TOTAL
TIME
ELAPSED TIME
11
2C53601A (E)p02-13 11 3/10/04, 11:31
Introduction
Identification of Controls (continued)
The instructions in this manual describe the functions on the remote control. See the page in for details.
Remote control
CALL button 24
DISPLAY button 59
VCR DVD selector button 22
Direct channel selection buttons 28
Number buttons 45
INPUT SELECT button 40
PROGRESSIVE button 66
TV/VCR button 22
COUNTER RESET button
ANGLE button 54
32
SP/SLP button 34
PLAY MODE button 52
REC button
OTR button
34
36
TIMER REC button 37
PLAY button 30
REW button 30
SLOW button 31
MARKER button 51
ZERO RETURN button 32
JUMP button 50
VCR MENU button 23
SETUP button 47
Direction buttons 45
( / / / )
SET +/- buttons 23
Channel +/– buttons 34
CANCEL button 37
VCR
DVD
CALL
DISPLAY
1
4
2
5
EJECT
3
6
OPEN/CLOSE
7
INPUT SELECT
PROGRESSIVE
8
TV/VCR
9
AUDIO SELECT
AUDIO
0
ATR
SUBTITLE
COUNTER RESET
ANGLE
SP/SLP
PLAY MODE A-B RPT CLOCK/COUNTER
REC/OTR TIMER REC
–
INDEX
SKIP
INDEX
SKIP
+
PLAY
REW
SLOW
FWD
STOP
PAUSE/STILL
ZERO RETURN
JUMP MARKER TOP MENU RETURN
VCR MENU
SETUP SET + MENU
CM SKIP
ZOOM
CH + CH –
CANCEL
ENTER
SET –
Power ( ) button 22
EJECT button (VCR) 29
OPEN/CLOSE button (DVD) 42
ATR button 31
SUBTITLE button 56
AUDIO SELECT button
AUDIO button 55
39
CLOCK/COUNTER button 33
INDEX + button 33
SKIP button 44
A-B RPT button 52
INDEX – button 33
SKIP button 44
FWD button 30
STOP button 30
PAUSE/STILL button 31
TOP MENU button 54
RETURN button 58
CM SKIP button
ZOOM button
31
50
*MENU button 54
ENTER button 23
12
2C53601A (E)p02-13 12
* MENU button
Use the MENU button to display the menu included on many DVD video discs. To operate a menu, follow the instructions in “DVD Menu.”
54
3/10/04, 11:31
Inserting batteries
1 Slide the battery compartment cover in the direction of the arrow.
2 Install two “R03/AAA” batteries
(supplied), paying attention to the polarity diagram in the battery compartment.
3 Replace the compartment cover.
Battery precautions
The precautions below should be followed when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to the device. To avoid a potential short circuit, insert the “–” end first.
3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery manufacturer’s directions.)
Remote control basics
• Press POWER ( ) to turn the DVD VCR on or off.
• Select your desired operating mode (DVD or VCR) using VCR DVD .
(DVD or VCR indicator on the front panel will show you which mode is selected.)
• Press CH + or CH – to move through the channels one channel at a time.
• The CH +/ – ( / ) and SET +/– ( / ) are also used to navigate on-screen menu system.
• You can directly access specific channels using Number buttons .
• Each press of VCR DVD on the remote control, switches the screen between the VCR screen (VCR mode) and the
DVD screen (DVD mode).
Operation
• Aim the remote control at the remote sensor and press control buttons to operate.
• Operate the remote control within 30
°
angle on either side of the remote sensor, up to a distance of Approx. 7 meters.
Approx. 7 meters
3/10/04, 11:31
13
2C53601A (E)p02-13 13
Connections
Antenna connections
If you are using an antenna system, follow these instructions. If you are a cable (CATV) subscriber, skip ahead to page 16 for the proper connections.
Antenna to DVD/VCR connection
The DVD/VCR must be connected “between” the antenna and the TV. First, disconnect the antenna from the TV and connect it to the DVD/VCR. Then connect the DVD/VCR to the TV. Below are 3 common methods of connecting an antenna system to a DVD/VCR. Find the type of antenna system you are using and follow the connection diagram.
1 Combination VHF/UHF Antenna with 75 ohm Coaxial Cable
DVD/VCR
75 ohm Coaxial Cable
IN
(ANT)
OUT
(TV)
2 Combination VHF/UHF Antenna with 300 ohm Twin Lead (Flat) Wire
DVD/VCR
Matching Transformer 300 ohm Input 75 ohm output (not supplied)
IN
(ANT)
OUT
(TV)
300 ohm Twin Lead (Flat) Wire
(not supplied)
Separate VHF and UHF Antennas
DVD/VCR 3
VHF
UHF
Combiner 75/300 ohm Inputs 75 ohm output
(not supplied)
300 ohm Twin Lead (Flat) Wire
(not supplied)
IN
(ANT)
OUT
(TV)
Note:
75 ohm Coaxial Cable
If both VHF and UHF antennas have 300 ohm twin lead (flat) wires, use a combiner having two 300 ohm inputs and one 75 ohm output.
Notes: • A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect the antenna to the DVD/VCR properly.
• For better quality recording, an indoor antenna or a telescopic antenna is not recommended. The use of an outdoor type antenna is required.
• If you are not sure about the connection, please refer to qualified service personnel.
14
2C53601A (E)p14-17 14 3/10/04, 11:31
DVD/VCR to TV connection
After you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV.
Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and follow the connection diagram.
This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antenna inputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for VHF and UHF reception.
75 ohm Coaxial Cable (supplied)
TV
VHF/UHF IN
Note: If a VHF or UHF antenna is used, set the TV/CATV menu option to the “TV” mode.
TV with single 75 ohm VHF/UHF antenna input
75 ohm Coaxial Cable
(supplied)
Splitter 75 ohm Input
75/300 ohm outputs
(not supplied)
75 ohm Coaxial Cable
(supplied)
Splitter 75 ohm Input
300 ohm outputs
(not supplied)
TV
UHF
VHF
Note: If a VHF or UHF antenna is used, set the TV/CATV menu option to the “TV” mode.
TV with 300 ohm UHF and 75 ohm VHF antenna inputs
TV
UHF
VHF
Note: If a VHF or UHF antenna is used, set the TV/CATV menu option to the “TV” mode.
TV with 300 ohm UHF and 300 ohm VHF antenna inputs
15
2C53601A (E)p14-17 15 3/10/04, 11:31
Connections
CATV (CABLE TV) connections
Many cable companies offer services permitting reception of extra channels including pay or subscription channels. This
DVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cable company supplied converter box, except for those premium channels which are intentionally scrambled. If you subscribe to a premium channel which is scrambled, you must have a descrambler box for proper reception.
1
DVD/VCR
TV
VHF/UHF
IN (ANT) Incoming Cable
IN
(ANT)
OUT
(TV)
2
Allows:
* Recording of nonscrambled channels.
* Use of the programmable timer.
* Recording of one channel while watching another.
DVD/VCR
Converter/
Descrambler
Incoming
Cable
IN
(ANT)
OUT
(TV)
Allows:
* Recording of channels through the converter box
(scrambled and unscrambled).
* Using the programmable timer to record only the channel selected at the converter box.
Prevents:
* Recording one channel while watching another.
* Using the DVD/VCR tuner to select channels.
TV
VHF/UHF
IN (ANT)
Note:
To record from converter/descrambler,
DVD/VCR tuner must be tuned to the converter output channel, usually channel 3 or 4.
DVD/VCR 3
Incoming Cable
IN
(ANT)
OUT
(TV)
Converter/Descrambler
TV
VHF/UHF
IN (ANT)
Allows:
* Recording of nonscrambled channels.
* Use of the programmable timer.
* Recording an unscrambled channel while watching any channel selected at the converter box.
Prevents: Recording scrambled channels.
Note:
If you are playing a tape or using the tuner built into the DVD/VCR, the converter must be set to the video channel output of the
DVD/VCR (either 3 or 4).
Note: Whenever a Converter/Descrambler box is placed before the DVD/VCR, you must tune the DVD/VCR to the output of the Converter/Descrambler box, usually channel 3 or 4.
16
2C53601A (E)p14-17 16 3/10/04, 11:31
IMPORTANT: Make sure the TV/CATV menu option is set to the “CATV” mode.
This DVD/VCR cannot receive scrambled programs since it does not contain a descrambler. In order to receive scrambled programs, your existing descrambler must be used. Descrambler boxes are available from cable companies. Consult your local cable company for more information concerning connection to their descrambler equipment. There are many ways to connect your DVD/VCR to a cable system. Below are six common methods of connection.
DVD/VCR
4
Splitter
TV
A/B Switch
VHF/UHF
IN (ANT)
Incoming Cable
Converter/Descrambler
IN
(ANT)
OUT
(TV)
A
B
Allows:
* Recording of one channel while watching another.
* Using the programmable timer to record only the channel selected at the converter box.
* Recording of all channels through the converter box.
Prevents:
* Watching scrambled channels while recording another channel.
* Using the DVD/VCR tuner to select channels.
5 DVD/VCR
TV
Splitter
IN
(ANT)
OUT
(TV)
VHF/UHF
IN (ANT)
Incoming Cable
Converter/Descrambler
A/B Switch
A
B
Allows:
* Recording of nonscrambled channels.
* Recording of one channel while watching another.
* Watching premium channels through the converter while recording nonscrambled channels.
* Using the programmable timer.
Prevents: Recording scrambled channels.
DVD/VCR
6
Splitter
Converter/Descrambler
TV
IN
(ANT)
OUT
(TV)
VHF/UHF
IN (ANT)
Incoming Cable
Converter/Descrambler
A/B Switch
A
B
Allows:
* Recording of all channels through the converter box.
* Recording a scrambled or unscrambled channel while watching another (scrambled or unscrambled) channel.
* Using the programmable timer to record only the channel selected at the converter box.
Prevents: Using the DVD/VCR tuner to select channels.
17
2C53601A (E)p14-17 17 3/10/04, 11:31
Connections
Connecting to a TV
Connect the DVD/VCR to your TV.
Note: This method transports VHS and DVD-video signals. For enhanced DVD-video performance, we recommend you also connect the S-video or ColorStream ® component video outputs to your TV/monitor 19 .
Connecting to a TV
Signal flow
To wall outlet
(yellow) (red) (white)
To ANALOG AUDIO OUT
To VIDEO
OUT
Audio/video cable (supplied)
To audio inputs
To video input
(yellow) (red) (white)
TV or monitor with audio/video inputs
Notes:
• Refer to the owner’s manual of the connected TV as well.
• When you connect the DVD/VCR to your TV, be sure to turn off the power and unplug both units from the wall outlet before making any connections.
• If your television set has one audio input, connect the left and right audio outputs of the DVD/VCR to a Y cable adapter (not supplied) and then connect to your TV.
• Connect the DVD/VCR directly to your TV. If you connect the DVD/VCR to a VCR, TV/VCR combination or video selector, the playback picture may be distorted as DVD video discs are copy protected.
18
2C53601A (E)p18-25 18 3/10/04, 11:31
S-video output/input
An S-Video connection is superior to Video (Yellow) output. Use this method for DVD playback when the connected television has S-
Video input, and does not have component video inputs.
Component video outputs/inputs
PROGRESSIVE outputs/inputs
Some TVs or monitors are equipped with component video inputs that are capable of reproducing a progressively scanned video signal. Connecting to these inputs allows you to view the highest quality pictures with less flicker.
INTERLACED outputs/inputs
Some TVs or monitors are equipped with component video inputs. Connecting to these inputs allows you to enjoy the highest quality
DVD picture playback.
Notes:
• Actual labels for component video inputs may vary depending on the TV manufacturer. (ex. Y, R-Y, B-Y or Y, CB, CR)
• In some TVs or monitors, the color levels of the playback picture may be reduced slightly or the tint may change. In such a case, adjust the TV or monitor for optimum performance.
Connecting to an audio system and TV equipped with S-video input/component video inputs
Note: The S-video output and component video output transports the DVD-video signal exclusively and will deliver enhanced DVD video picture performance.
Signal flow
(white) To ANALOG
AUDIO OUT
(red)
To S-
VIDEO
OUT
To P
R
/C
R
VIDEO
OUT
To P
B
/C
B
VIDEO
OUT
To Y
VIDEO
OUT
To wall outlet
When you make this connection, set the S-VIDEO/
COMPONENT Video selector switch to the desired position.
And also you must select the corresponding video input on your TV.
Component video cable (not supplied)
Audio cable (not supplied)
To audio inputs of the amplifier
To Y video input
(red) (white)
To P
B/
C
B
video input
To P
R/
C
R
video input
To S-video input
S-video cable (not supplied)
If you connect the DVD/VCR to your TV with the DVD OUT jacks, select the corresponding video input on your television to watch DVD video discs.
TV or monitor with
ColorStream ® component video inputs
Audio system
Notes:
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD/VCR to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections.
• If you place the DVD/VCR near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the DVD/
VCR away from the tuner and radio.
• The output sound of the DVD/VCR has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the DVD/VCR’s power cord. If you leave the amplifier power on, the speakers may be damaged.
• When connecting to a TV using the Video or S-video jack, make sure that the Progressive indicator “ ” on the display window is not lit. If it is lit, the Video and S-video outputs do not feed the correct signals and you cannot see any picture. To turn off the Progressive indicator, select PROGRESSIVE scan Off 66 .
19
2C53601A (E)p18-25 19 3/10/04, 11:31
Connections
Connecting to optional equipment
You can enjoy high quality dynamic sounds of DVD video discs or audio CDs by connecting the DVD/VCR to optional audio equipment.
For connection to your TV, see “Connecting to a TV” 18 19 .
• This selection uses the following reference mark.
: Front speaker
: Rear speaker
: Sub woofer
: Center speaker
: Signal flow
Connecting to an amplifier equipped with a Dolby Digital decoder
Dolby Digital
Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is now available to reproduce this realistic effect in the home. You can enjoy motion picture and live concert DVD video discs with this dynamic realistic sound by connecting the
DVD/VCR to a 6 channel amplifier equipped with a Dolby Digital decoder or Dolby Digital processor. If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of
Pro Logic from the same DVD movies that provide full 5.1-channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark.
Manufactured under license from
Dolby Laboratories. “Dolby” “Pro
Logic” and the double-D symbol are trademarks of Dolby Laboratories.
• Use DVD video discs encoded via the Dolby Digital recording system.
Amplifier equipped with a
Dolby Digital decoder
To COAXIAL type digital audio input
To OPTICAL type digital audio input
Optical digital cable
75 Ω coaxial cable
Connect either.
Connecting to an amplifier equipped with Dolby Surround Pro Logic
Dolby Surround Pro Logic
You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting an amplifier and speaker system (right and left front speakers, a center speaker, and one or two rear speakers).
With an amplifier equipped with Dolby Digital
Connect the equipment the same way as described in “Connecting to an amplifier equipped with a Dolby Digital decoder.” Refer to that amplifier’s owner’s manual and set the amplifier so you can enjoy Dolby Surround Pro Logic sound.
With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.
• This connectin is only suitable for Video CDs and Audio CDs.
* Amplifier equipped with
Dolby Surround Pro Logic
* Connect one or two rear speakers.
The output sound from the rear speakers will be monaural even if you connect two rear speakers.
To Audio input
To ANALOG AUDIO OUT
Audio cable
Connecting to an amplifier equipped with a DTS decoder
Digital Theater Systems (DTS)
DTS is a high quality surround technology used in theaters and now available for home use, on DVD video discs or audio CDs.
If you have a DTS decoder or processor, you can obtain the full benefit of 5.1 channel DTS encoded sound tracks on DVD video discs or audio CDs.
Amplifier equipped with a
DTS decoder
“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
• Use DVD video discs or audio
CDs encoded via the DTS recording system.
To COAXIAL type digital audio input
To OPTICAL type digital audio input
Optical digital cable
75 Ω coaxial cable
Connect either.
20
2C53601A (E)p18-25 20 3/10/04, 11:31
Warning
When playing DTS-encoded discs (audio CDs), excessive noise may be output from the analog stereo jacks. To avoid possible damage to the audio system, you should take proper precautions when the ANALOG AUDIO OUT (L/R) jacks of the
DVD/VCR are connected to an amplification system. (Do not leave the ANALOG AUDIO OUT (L/R) wires dangling.) To enjoy
DTS Digital Surround™ playback, an external 5.1 channel DTS Digital Surround™ decoder system must be connected to the
BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR.
Connecting to an amplifier equipped with an MPEG2 audio decoder
MPEG2 sound
You can enjoy motion picture and live concert DVD video discs with dynamic realistic sound by connecting an amplifier equipped with an MPEG2 audio decoder or MPEG2 audio processor.
• Use DVD video discs encoded via the MPEG2 recording system.
Amplifier equipped with an
MPEG2 audio decoder
To COAXIAL type digital audio input
To OPTICAL type digital audio input
Optical digital cable
75
Ω
coaxial cable
Connect either.
Connecting to an amplifier equipped with a digital audio input
2 channel digital stereo
You can enjoy the dynamic sound of 2 channel digital stereo by connecting an amplifier equipped with a digital audio input and speaker system (right and left front speakers).
Amplifier equipped with a digital audio input
To COAXIAL type digital audio input
To OPTICAL type digital audio input
Optical digital cable
75 Ω coaxial cable
Connect either.
Notes:
• DO NOT connect the BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR to the AC-3 RF input of a Dolby Digital Receiver.
This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the BITSTREAM/PCM AUDIO
OUT jack of the DVD/VCR.
• Connect the BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR to the “OPTICAL” or “COAXIAL” input of a Receiver or
Processor.
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD/VCR to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections.
• The output sound of the DVD/VCR has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the DVD/VCR’s power cord. If you leave the amplifier power on, the speakers may be damaged.
21
2C53601A (E)p18-25 21 3/10/04, 11:31
Basic setup
Setting the video channel
When a TV is connected with the 75 ohm coaxial cable only.
To view playback of a recorded tape or DVD disc, or to watch a program selected by the VCR's channel selector, the TV must be set to channel 3 or 4 (video channel).
POWER
3
4
TV/VCR
VCR DVD
Setting the video channel
1 Press and hold 3 or 4 on the remote for 3 seconds in standby mode.
3 OR 4
The video channel will start to flash for 3 seconds in the display window.
2 Press POWER to turn on the DVD/VCR.
For a push-button TV tuner
If CH 3 or 4 corresponding to the video channel cannot be tuned on your TV, proceed as follows: set the VCR
3/4 channel selector and the TV to CH 3 or 4, play back a prerecorded tape and tune the TV to receive a sharp color picture from the video cassette recorder.
Refer to your TV owner's manual for details.
Note:
If the unit does not operate properly, or No key operation
(by the unit and/or the remote control): Static electricity, etc., may affect the player's operation. Disconnect the AC power cord once, then connect it again.
3 Press VCR DVD selector to select the VCR mode.
VCR
DVD
The VCR indicator on the front panel will light.
4 Turn ON the TV and set to CH 3 or 4 to correspond with the channel selected in step 1.
5 Press TV/VCR to select the VCR position.
TV/VCR The VCR indicator will appear in the display window.
6 Select any channel to receive a TV station in your area.
The channel number will appear on the screen for about 4 seconds.
22
2C53601A (E)p18-25 22 3/10/04, 11:31
VCR DVD
Setting the language
You can choose from three different languages (English,
French and Spanish) for the on-screen displays.
1,4
1–3
1–3
Setting the language
Preparation:
• Turn ON the TV and select to the corresponding video input.
• Press VCR DVD selector to select the VCR mode.
(The VCR indicator will light.)
4 Press VCR MENU until the MENU screen is cleared.
VCR MENU
SETUP
1 Press VCR MENU.
The VCR menu screen will appear.
Press SET + or – to select “SYSTEM
VCR MENU
SETUP
SETUP”, then press ENTER .
If you use the unit for the first time and press VCR MENU , instead of the main menu screen the “SYSTEM SETUP” menu screen in step 2 may appear.
SET +
CH –
ENTER
SET –
CH +
MENU
TIMER REC SET
AUTO REPEAT ON OFF
SAP
CH SETUP
SYSTEM SETUP
ON OFF
Notes:
• Both the VCR and the DVD have their own player menus 57 .
• If no buttons are pressed for more than 60 seconds, the VCR
MENU screen will return to normal TV-operation automatically.
á+/-/ENTER/MENU ñ
2 Press SET + or – to select “LANGUAGE”, then press ENTER.
SET +
CH –
ENTER
SET –
CH +
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
ON OFF
ON OFF
DAYLIGHT SAVING TIME
á+/-/ENTER/MENU ñ
3 Press SET + or – to select the desired language:
English (ENGLISH), Spanish (ESPAÑOL) or
French (FRANCAIS), then press ENTER.
SET +
CH –
ENTER
SET –
CH +
á+/-/ENTER/MENU ñ
23
2C53601A (E)p18-25 23 3/10/04, 11:31
Basic setup
Clock setting
The AUTO CLOCK function will automatically set the built-in clock
(Month, Day, Year and Time) when the DVD/VCR is connected to an
Antenna or Cable system and it is turned off. The DVD/VCR searches for a station in your area containing the necessary AUTO CLOCK setting signals. Once received, it will take approximately 4 minutes for the clock to set itself automatically.
AUTO CLOCK setting
Preparation:
• Turn ON the TV and select the corresponding video input.
• Press VCR DVD selector to select the VCR mode.
(The VCR indicator will light.)
1 Connect the Antenna or Cable system.
• If you use a cable box, turn it on.
2 Plug the AC Power cord to the AC outlet.
3 Make sure the DVD/VCR is turned off.
• If you press POWER , the Auto Clock
set is not programmed.
4 Wait at least three minutes and press
POWER.
1,5
2,4
2,3
To set AUTO CLOCK to off
When shipped from factory the AUTO CLOCK is set to “ON”.
But if you do not want AUTO CLOCK setting:
1 Press VCR MENU.
VCR MENU
SETUP
MENU
TIMER REC SET
AUTO REPEAT ON OFF
SAP
CH SETUP
SYSTEM SETUP
ON OFF
2
CALL
POWER
VCR DVD
Press SET + or – to select “SYSTEM SETUP”, then press ENTER.
CH –
SET +
ENTER
SET –
CH +
MENU
TIMER REC SET
AUTO REPEAT ON OFF
SAP
CH SETUP
SYSTEM SETUP
ON OFF
á+/-/ENTER/MENU ñ
5 Press CALL to check the clock setting on the on screen display.
CALL
DISPLAY
8 : 47 AM MON
STEREO SAP
CH 125
3 Press SET + or – to select “AUTO CLOCK”.
CH –
SET +
ENTER
SET –
CH +
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
ON OFF
ON OFF
DAYLIGHT SAVING TIME
á+/-/ENTER/MENU ñ
00 : 00 : 00 SP
6 If the clock is not set, check the antenna condition. The AUTO CLOCK may not function properly if the reception condition is not good.
4 Press ENTER to select “OFF”.
CH –
SET +
ENTER
SET –
CH +
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
ON OFF
ON OFF
DAYLIGHT SAVING TIME
á+/-/ENTER/MENU ñ
AUTO CLOCK adjustment
24
The auto clock adjustment will be updated at 6:00
AM, 12:00 PM and 6:00 PM everyday when the
DVD/VCR turned off.
• If you use a cable box and you want AUTO CLOCK adjustment to be performed, the cable box must be left on.
• The AUTO CLOCK adjustment is not effective when there is a difference of more than 5 minutes exists between the built-in clock time and the actual time.
5 Press VCR MENU repeatedly to return to the normal screen.
VCR MENU
SETUP
• When the AUTO CLOCK is set to
“OFF”, the AUTO CLOCK adjustment does not function.
• Set the clock manually 26 .
2C53601A (E)p18-25 24 3/10/04, 11:31
To set STANDARD TIME To set DAYLIGHT SAVING TIME
In the rare event that you live within broadcast range of two stations in two different time zones, the DVD/VCR may recognize the wrong station for the AUTO CLOCK setting.
To correct the situation:
1 Press VCR MENU.
VCR MENU
SETUP
MENU
TIMER REC SET
AUTO REPEAT ON OFF
SAP
CH SETUP
SYSTEM SETUP
ON OFF
You can set the DAYLIGHT SAVING TIME automatically or manually.
1 Press VCR MENU.
Press SET + or – to select “SYSTEM SETUP”, then press ENTER.
VCR MENU
SETUP
SET +
MENU
TIMER REC SET
AUTO REPEAT ON OFF
SAP
CH SETUP
SYSTEM SETUP
ON OFF
CH – CH +
ENTER
SET –
á+/-/ENTER/MENU ñ
2 Press SET + or – to select “SYSTEM SETUP”, then press ENTER.
SET +
CH –
ENTER
SET –
CH +
MENU
TIMER REC SET
AUTO REPEAT ON OFF
SAP
CH SETUP
SYSTEM SETUP
ON OFF
á+/-/ENTER/MENU ñ
2 Press SET + or – to select “DAYLIGHT
SAVING TIME”, then press ENTER.
CH –
SET +
ENTER
SET –
CH +
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
ON OFF
ON OFF
DAYLIGHT SAVING TIME
á+/-/ENTER/MENU ñ
3 Press SET + or – to select “STANDARD TIME”, then press ENTER.
CH –
SET +
ENTER
SET –
CH +
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
ON OFF
ON OFF
DAYLIGHT SAVING TIME
á+/-/ENTER/MENU ñ
3 Press SET + or – to select one of the options, then press ENTER. Press VCR
MENU until the MENU screen is cleared.
4
CH –
Press SET + or – to select your time zone, then press ENTER.
SET +
ENTER
SET –
CH +
ATLANTIC : GMT–4hours
EASTERN : GMT–5hours
CENTRAL : GMT–6hours
MOUNTAIN : GMT–7hours
PACIFIC
ALASKA
HAWAII
AUTO
: GMT–8hours
: GMT–9hours
: GMT–10hours
: AUTO SET
(GMT: Greenwich Mean Time)
CH –
VCR MENU
SETUP
SET +
ENTER
SET –
CH +
ON:
OFF:
AUTO: for manual setting
(forward one hour) for manual setting
(back one hour) for automatic setting
(read XDS in the signal)
When you want to set the DAYLIGHT
SAVING TIME manually, on the first
Sunday in April you set to “ON”, and on the last Sunday in October you set to “OFF”.
5 Press VCR MENU twice to return to the normal screen.
VCR MENU
SETUP
DAYLIGHT SAVING TIME
ON
OFF
AUTO
á+/-/ENTER/MENU ñ
Notes:
• To be able to select the standard time, the clock must first be set by AUTO CLOCK once.
• If you live in Newfoundland and the AUTO CLOCK does not function properly, set the AUTO CLOCK menu option to “OFF” and set the clock manually.
Notes:
• When shipped from factory, the DAYLIGHT SAVING TIME is set to “AUTO” position.
• When the clock is not set, DAYLIGHT SAVING TIME setting is not available.
• When there is no DAYLIGHT SAVING TIME in your area, always select “OFF” position in step 3.
25
2C53601A (E)p18-25 25 3/10/04, 11:31
Basic setup
Clock setting (continued)
If the AUTO CLOCK process did not set the date and time correctly, you must set them manually for timer recording and DAYLIGHT
SAVING TIME.
1
2–4
CANCEL
2–4
Manual clock setting
EXAMPLE: Setting the clock to “8:30 AM” March,
27 (SAT), 2004.
1 Press VCR MENU.
VCR MENU
SETUP
6 After setting the clock, date and time starts functioning automatically.
8 : 30 AM SAT
2 Press SET + or – to select “SYSTEM SETUP”, then press ENTER.
CH –
SET +
CH +
MENU
TIMER REC SET
AUTO REPEAT ON OFF
SAP
CH SETUP
SYSTEM SETUP
ON OFF
ENTER
SET –
á+/-/ENTER/MENU ñ
3 Press SET + or – to select “CLOCK SET”, then press ENTER.
CH –
SET +
ENTER
SET –
CH +
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
ON OFF
ON OFF
DAYLIGHT SAVING TIME
á+/-/ENTER/MENU ñ
4 Press SET + or – to set the month, then press
ENTER.
CH –
SET +
ENTER
SET –
CH +
MONTH
DAY
YEAR
3
1 (MON)
2004
TIME 12 : 00 AM
⟨
+/–/ENTER/CANCEL/MENU
⟩
To make corrections any time during the process
Press CANCEL repeatedly until the item you want to change blinks, then press SET + or – .
Note:
After a power failure or disconnection of the power, the timer settings will be lost. In this case, reset the present time.
5 Set the day, year and time as in step 4.
MONTH
DAY
YEAR
3
27 (SAT)
2004
TIME 8 : 30 AM
á +/–/ENTER/CANCEL/MENU ñ
26
2C53601A (E)p26-31 26 3/10/04, 11:32
Tuner setting
This DVD/VCR is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory, skipping over unwanted channels. Before selecting channels, they must be programmed into the DVD/VCR’s memory. In addition to normal
VHF and UHF channels, this DVD/VCR can receive up to 113 Cable
TV channels. To use this DVD/VCR with an antenna, set the TV/CATV menu option to the TV mode. When shipped from the factory, this menu option is in the CATV mode.
TV/CATV selection
VCR DVD
1,4
1,3
1,2
Setting channels automatically
Preparation:
• Turn ON the TV and select to the corresponding video input.
• Press VCR DVD selector to select the VCR mode.
(The VCR indicator will light.)
1 Press VCR MENU. Press SET + or – to select
“CH SETUP”, then press ENTER.
VCR MENU
SETUP
SET +
MENU
TIMER REC SET
AUTO REPEAT ON OFF
SAP
CH SETUP
SYSTEM SETUP
ON OFF
CH – CH +
ENTER
SET –
á+/-/ENTER/MENU ñ
2 Press SET + or – to select “TV/CATV”.
SET +
CH SETUP
TV CATV
AUTO CH MEMORY
ADD/DELETE CH –
ENTER
CH +
SET –
á+/-/ENTER/MENU ñ
3 Press ENTER to select the TV or CATV mode.
The arrow indicates the selected mode.
SET +
CH – CH +
ENTER
SET –
CH SETUP
TV CATV
AUTO CH MEMORY
ADD/DELETE
TV - VHF/UHF channels
CATV - CABLE TV channels á+/-/ENTER/MENU ñ
4 Press VCR MENU until the menu screen is cleared.
VCR MENU
SETUP
1 Repeat left step 1 and press SET + or – to select “AUTO CH MEMORY”.
CH –
SET +
CH +
CH SETUP
TV CATV
AUTO CH MEMORY
ADD/DELETE ENTER
SET –
á+/-/ENTER/MENU ñ
2 Press ENTER.
Auto tuning will begin. The channel display will count up and when finished, the screen returns to normal.
SET +
CH –
ENTER
SET –
CH +
CH 002
Note:
You can’t select “CH SETUP” if you set the channel to “L1” or
“L2”.
27
2C53601A (E)p26-31 27 3/10/04, 11:32
Basic setup
Tuner setting (continued)
NUMBER BUTTONS
To ADD/DELETE channels
1 Repeat the step 1 on page 27. Then press SET + or – to select the “ADD/DELETE” and press
ENTER.
CH SETUP
SET +
TV CATV
AUTO CH MEMORY
ADD/DELETE
CH – CH +
ENTER
SET –
á
+/-/ENTER/MENU
ñ
2 To Add or Delete desired channels
1
Press Number buttons or SET + or – to select a channel number you want to add or delete.
2 To add channels
Press ENTER until “ADD” appears on the screen.
To delete channels
Press ENTER until “DELETE” appears on the screen. The channel number will blink.
3 1 2
SET +
1
4
7
2
5
8
3
6
9 0
CH –
ENTER
SET –
CH +
3
1,2
1,2
Noise elimination
When you don't want to receive a weak signal broadcast, a
Blue back screen can be obtained by selecting the NO NOISE
BACKGROUND “ON”. When the unit is shipped from the factory, the NO NOISE BACKGROUND is set to “ON”.
Repeat the steps 1~2 on page 26 and press 1
SET + or – to select “NO NOISE
BACKGROUND”.
CH –
SET +
ENTER
SET –
CH +
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
ON OFF
ON OFF
DAYLIGHT SAVING TIME
á+/-/ENTER/MENU ñ
2 Press ENTER to select “ON” or “OFF” position.
CH –
SET +
ENTER
SET –
CH +
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
ON OFF
ON OFF
DAYLIGHT SAVING TIME
á+/-/ENTER/MENU ñ
3 Press VCR MENU until the menu screen is cleared.
VCR MENU
SETUP
3 Press VCR MENU until the menu screen is cleared.
VCR MENU
SETUP
28
2C53601A (E)p26-31 28 3/10/04, 11:32
Playback (VCR)
Loading and unloading a cassette tape
Use only video cassette tapes marked and .
EJECT
Loading
Push the center of the tape until it is automatically inserted.
Insert the cassette tape with its labeled side facing up and the erase prevention tab positioned at your left. An inverted cassette tape cannot be inserted.
Erase prevention tab
Automatic power ON
When you insert a cassette tape the DVD/VCR power will turn ON automatically.
Automatic playback
When loading a cassette tape without an erase prevention tab, playback will start automatically.
Unloading
1 Press EJECT on the front panel or on the Remote.
2 Remove the cassette tape.
Automatic tape eject
This DVD/VCR will automatically rewind the tape when the tape has ended. Once the tape is rewound to its beginning, the cassette tape will be ejected automatically.
To prevent accidental erasure
To prevent accidental erasure
Remove the erase prevention tab with a screwdriver.
Screwdriver
To record again
Cover the hole with a piece of adhesive tape.
Erase prevention tab
Tape speed and maximum recording time
Tape Speed
SP (Standard Play)
SLP (Super Long Play)
T-160
2-2/3 hours
8 hours
Adhesive tape
T-120
2 hours
6 hours
Video cassette tape
T-90
1-1/2 hours
4-1/2 hours
T-60
1 hour
3 hours
T-30
30 minutes
1-1/2 hours
29
2C53601A (E)p26-31 29 3/10/04, 11:32
Playback (VCR)
Cassette tape playback
To play a prerecorded tape.
VCR DVD
REW
PLAY
FWD
STOP
Playback
Preparation:
• Turn ON the TV and select the corresponding video input.
• Press VCR DVD selector to select the VCR mode.
(The VCR indicator will light).
1 Load a prerecorded tape
(When loading a cassette tape without the erase prevention tab, playback will start automatically).
Rewind or forward the tape
Stop the playback or recording via STOP on remote.
To rewind the tape:
Press REW .
REW
2 To start playback
Press PLAY .
Playback will start. “ ” will appear on the screen for about 4 seconds.
PLAY
To forward the tape:
Press FWD .
FWD
To stop playback
Press STOP once.
The tape will stop but remain fully loaded and ready to play.
“ ” will appear on the screen for about 4 seconds.
To discontinue the tape-winding, press STOP . To switch to playback directly (without STOP ), press PLAY .
Forward/Reverse picture search mode
When the tape is being winded, you can switch to picture search mode (see next page). To do this, press REW or
FWD and hold it down. The unit will resume the tape advance or rewinding as soon as the button is released.
Notes:
• This VCR selects the playback tape speed SP, LP or SLP automatically.
• The Cassette tape and DVD disc can be played back simultaneously. If you press VCR DVD selector, the tape playback and DVD playback alternate with each other on the screen
(via CH3, 4 or video connection).
30
2C53601A (E)p26-31 30 3/10/04, 11:32
Special playback
SLOW
ATR
REW
PLAY
FWD
PAUSE/STILL
CM SKIP
SET +/–
Picture search
Reverse picture search function
Press REW once or twice during playback.
Forward picture search function
Press FWD once or twice during playback.
To return to playback, press PLAY .
SPEED SEARCH TIMES
TAPE SPEED
SP (Standard Play)
LP (Long Play)
SLP (Super Long Play)
PICTURE SEARCH SPEED
PRESS ONCE PRESS TWICE
3 X
7 X
5 X
9 X
9 X 15 X
Adjusting tracking condition
Automatic tracking adjustment
Whenever you insert a tape and start playback, the automatic tracking feature continuously analyzes the signal to enable optimum picture quality during playback.
Manual tracking adjustment
If automatic tracking cannot eliminate noises well during playback, press SET +/– to eliminate the noise. “MANUAL
TR.” will appear on the screen. Press it briefly for a fine adjustment, or press and hold for a coarse adjustment.
Press ATR to reactivate automatic tracking again.
“AUTO TR.” will appear on the screen.
Still picture
Press PAUSE/STILL during playback.
To resume normal playback, press PLAY or PAUSE/STILL .
Slow motion
During playback press SLOW .
To return to playback, press PLAY or SLOW .
Slow tracking and vertical lock adjustment
If noise bars appear in the picture during slow motion, press the SET + /– to reduce the noise bars.
If the still picture jitters excessively, press SET +/– to stabilize the still picture.
Frame by frame picture
Press PAUSE/STILL during playback.
Press SLOW repeatedly: The picture advances frame by frame.
To return to playback, press PLAY or PAUSE/STILL .
CM skip
Press CM SKIP during playback. The DVD/VCR will search forward through approximately 30 seconds of the tape (e.g.
unwanted commercial time) for each press of CM SKIP
(maximum six presses) and then resume normal playback.
For example : 1 press: 30 seconds of tape
2 press: 60 seconds of tape
3 press: 90 seconds of tape
AUTO TR.
Notes:
• The audio output is muted during SPEED SEARCH, STILL,
FRAME ADVANCE and SLOW MOTION.
• During picture search mode there will be noise bars. This is not a defect.
• Playback will commence after approx. 5 minutes to protect the video tape against excessive wear during pause mode.
Video head cleaning
Video head clogging
The video heads are the means by which the DVD/VCR reads the picture from the tape during playback. In the unlikely event that the heads become dirty enough to be clogged, no picture will be displayed. This can easily be determined if, during playback of a known good tape, there is good sound, but no picture (picture is extremely snowy). If this is the case, have the
DVD/VCR checked and cleaned by qualified service personnel.
Good Picture
Snowy Picture
Notes:
• DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR
SERVICE THE UNIT BY REMOVING THE REAR COVER.
• Video heads may eventually wear out and should be replaced when they fail to produce clear pictures.
• To help prevent video head clogging, use only good quality VHS tapes. Discard worn out tapes.
31
2C53601A (E)p26-31 31 3/10/04, 11:32
Playback (VCR)
Convenience function
CALL
COUNTER RESET
CLOCK/COUNTER
VCR MENU
PLAY
STOP
ZERO RETURN
ENTER
SET +/–
Repeat playback
The entire video tape will play until its end. The tape will automatically rewind to the beginning and the playback will be repeated.
1 Press VCR MENU.
Press SET + or – to select “AUTO
REPEAT”.
VCR MENU
SETUP
CH –
SET +
CH +
MENU
TIMER REC SET
AUTO REPEAT ON OFF
SAP
CH SETUP
SYSTEM SETUP
ON OFF
ENTER
SET –
á+/-/ENTER/MENU ñ
Zero return function
This function rewinds the tape to the “00:00:00” counter position automatically.
1 Press CLOCK/COUNTER.
The counter display shows the tape running time during playback or recording.
CLOCK/COUNTER
2 Press ENTER to select “ON” or “OFF”.
CH –
SET +
ENTER
SET –
CH +
If “ON” is selected, the playback will be repeated endlessly.
MENU
TIMER REC SET
AUTO REPEAT ON OFF
SAP
CH SETUP
SYSTEM SETUP
ON OFF
á+/-/ENTER/MENU ñ
2 Press COUNTER RESET at the desired tape position.
The counter display will be reset to
“00:00:00” position (e.g. the beginning of recording).
COUNTER RESET
ANGLE
3 Press VCR MENU until the menu screen is cleared.
If you press CALL , “ ” will
appear on the screen 11 .
3 Press STOP when playback or recording is completed.
Press ZERO RETURN.
The tape will automatically rewind or fast forward to the “00:00:00” counter position.
4 To commence playback, press PLAY.
The playback will be repeated
endlessly.
PLAY
ZERO RETURN
JUMP
To cancel repeat mode :
Follow the above step 1 , then press ENTER to select
“OFF” position. Press VCR MENU to return to the TV.
32
2C53601A (E)p32-37 32 3/10/04, 11:32
VCR DVD
CLOCK/COUNTER
INDEX + / –
STOP
Clock/counter display
Press CLOCK/COUNTER . The clock and tape counter alternate with each other in the display window.
COUNTER
CLOCK/COUNTER
Video index search system
This function enables you to locate the beginning of any recording made on the VCR.
Recording an INDEX mark
The Index Search function automatically records an INDEX mark on the tape whenever a recording is initiated.
INDEX
CH 001
Press VCR DVD selector. The DVD mode and the
VCR mode alternate with each other in the display.
VCR
DVD
CLOCK
DVD mode
Index search
Press INDEX + or – during stop or play mode.
For Succeeding programs: Press INDEX + .
For Preceding programs: Press INDEX – .
(As many as 9 index points can be accessed via this method.)
When the INDEX + or – is pressed, the unit starts searching the INDEX
NO. selected and finds the portion,
+3 then playback starts automatically.
To stop the Index Search, press
STOP .
–
INDEX
SKIP
INDEX
SKIP
+ or is displayed
INDEX NO. (up to 9)
VCR mode
Notes:
• If you rewind the tape beyond “00:00:00”, a minus sign (“–”) will be displayed in front of the time.
• When you load a tape, the counter will reset to “00:00:00”.
• The counter does not function on nonrecorded (blank) sections of the tape. When you rewind, fast forward or play tapes through blank sections, the counter stops.
Notes:
• When you record an INDEX mark at the very beginning of the tape, the mark may not be found.
• During INDEX search, the tape may stop and begin to play at a slightly different location.
• INDEX may not function properly with old or worn out video tapes.
• INDEX marks may not be found if it is extremely close to the point where the search began.
• In recording, if you stop recording temporarily, the INDEX mark is not recorded on the tape.
SQPB (S-VHS Quasi Playback)
You can playback video cassette tapes recorded in the
S-VHS system.
However, the picture will not have the high resolution of
S-VHS system.
Note: You cannot record S-VHS video format with this VCR.
33
2C53601A (E)p32-37 33 3/10/04, 11:32
Recording (VCR)
Recording a TV program
Recording and viewing the same TV program.
VCR DVD
4
2
5
4
Recording a TV program
Preparation:
• Turn ON the TV and select to the corresponding video input.
• Press VCR DVD selector to select the VCR mode.
(The VCR indicator will light.)
1 Load a cassette tape with the erase prevention tab intact.
The DVD/VCR will automatically turn on.
4 Press Number buttons or CH +/– to select the channel to be recorded.
SET +
1
4
7
2
5
8
3
6
9 0
CH –
ENTER
SET –
CH +
CH 110
2 Press SP/SLP to select the desired tape speed
SP or SLP.
3
SP/SLP
PLAY MODE
The tape counter and “SP” or “SLP” will appear on the screen for about 4 seconds.
00 : 00 : 00 SP
Select “TV” or “CATV” to the appropriate position 27 .
TV - VHF/UHF channels
CATV - CABLE TV channels
TV mode direct channel selection:
All channels can be instantly selected by using two buttons. (for example, to select channel 2, press “0”, then
“2”. If you press only “2”, channel selection will be delayed for two seconds.) For channels 10 and above, press the 2 digits in order.
CATV mode direct channel selection:
1-9 Press 0 twice and then 1-9 as required.
Example: To select “2”, Press 002 .
10-12 Press 0 first and then the remaining 2 digits in order from left to right.
Example: Press 012 for “12”.
Press 2 digits in order.
13-99
Example: Press 22 for “22”.
100-125 Press the 3 digits in order.
Example: Press 110 for “110”.
VHF/UHF/CATV CHANNELS
TV
VHF
2-13
UHF
14-69
CATV
VHF
2-13
STD/HRC/IRC
14-36 (A) (W)
37-59 (AA) (WW)
60-85 (AAA) (ZZZ)
86-94 (86) (94)
95-99 (A-5) (A-1)
100-125 (100)(125)
01 (5A)
5 Press REC/OTR.
“ ” will appear on the screen
for about 4 seconds and “REC” will
appear on the display window.
REC/OTR
CH 110
INDEX
34
2C53601A (E)p32-37 34 3/10/04, 11:32
TV/VCR
PAUSE/STILL
STOP
To stop recording
Press STOP to stop recording.
“ ” will appear on screen for about
4 seconds.
Auto Rewind feature
This VCR will automatically rewind the tape when the tape has ended (except during OTR and timer recording). It will also eject the tape.
To stop recording temporarily
Press PAUSE/STILL to avoid recording unwanted material. Press again to continue the recording.
“ ” will appear on screen for
about 4 seconds.
Notes:
• The pause function will be released after 5 minutes to prevent damage to the tape or the VCR. The VCR will change to the
STOP mode.
• You can select a recording channel in the recording pause mode.
Recording one program while watching another
While the VCR is recording, select your desired channel on the TV.
When a TV is connected with an antenna cable only, press TV/VCR to select the TV position.
The “VCR” display will go off and recording will continue.
Select the TV channel you want to watch by using the
TV channel selector.
Note:
Some CATV hookups do not permit viewing one channel while recording another. See pages 16 and 17 .
2C53601A (E)p32-37 35 3/10/04, 11:32
35
Recording (VCR)
One-touch Timer Recording (OTR)
The One-touch Timer Recording feature provides a simple and convenient way to make a timed recording.
VCR DVD
4
2
5
STOP
4
One-touch Timer Recording (OTR)
Preparation:
• Turn ON the TV and select to the corresponding video input.
• Press VCR DVD selector to select the VCR mode.
(The VCR indicator will light.)
Example: One-touch Timer Recording for 30 minutes.
1 Load a cassette tape with the erase prevention tab intact.
The VCR will automatically turn on.
4 Press Number buttons or CH +/– to select the channel to be recorded.
CH 110
1
4
7
2
5
8
3
6
9 0
CH –
SET +
ENTER
SET –
CH +
2 Press SP/SLP to select the desired tape speed
SP or SLP.
SP/SLP
PLAY MODE
The tape counter and “SP” or “SLP” will appear on the screen for about 4 seconds.
5 Press REC/OTR. Recording begins. Press the button again to stop recording after 30 minutes.
Each additional press of REC/OTR will increase recording time as shown in the chart below, up to a maximum of 6 hours.
The OTR and recording time will appear on the screen for about 4 seconds. And, “ ” will appear on the display.
Press once twice
3 times
4 times
5 times
Recording time Press
NORMAL REC
0:30
6 times
7 times
1:00
1:30
2:00
8 times
9 times
10 times
Recording time
3:00
4:00
5:00
6:00
NORMAL REC
OTR 0 : 30
CH 110
REC/OTR
00 : 00 : 00 SP
INDEX
3 Set “TV” or “CATV” option to the appropriate position 27 .
TV - VHF/UHF channels
CATV - CABLE TV channels
To cancel OTR
Press STOP or turn off the power.
36
2C53601A (E)p32-37 36
“ ” will appear on screen for about 4 seconds.
Note:
If you wish to watch the DVD playback during OTR or standard recording, press VCR DVD selector to change to DVD mode and perform the DVD playback 43 .
3/10/04, 11:32
Timer recording
Timer recording can be programmed on-screen with the remote control.
The built-in timer allows automatic unattended recording of up to 8 programs within 1 month.
VCR DVD
EJECT
2,3
TIMER REC
1,5
1–3
CANCEL
Timer recording
Preparation:
• Press VCR DVD selector to select the VCR mode.
• Load a cassette tape with the erase prevention tab intact.
• Check the time and date are correct 24 .
Example: Program a timer recording for the 26th day, channel 125 (CATV), 11:00 - 11:30 PM on timer program number 1 (Tape speed: SLP).
1 Press VCR MENU. Select “TIMER REC SET”, then press ENTER.
VCR MENU
SETUP
CH –
SET +
ENTER
CH +
MENU
TIMER REC SET
AUTO REPEAT ON OFF
SAP
CH SETUP
SYSTEM SETUP
ON OFF
SET –
5 To enter other programs, repeat step 2 through 4.
VCR MENU
SETUP
• To return to the normal screen, press VCR MENU twice.
DATE START END CH
26(SU) 11:00 PM 11:30 PM 125 SLP
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð
Ð
Ð
Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
á+/Ð/ENTER/CANCEL/MENU ñ
Ð
Ð
Ð
2 Press SET + or – to select one of the program line, then press ENTER.
CH –
SET +
ENTER
SET –
CH +
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
á+/Ð/ENTER/CANCEL/MENUñ
Ð
Ð
Ð
Ð
Ð
Ð
Ð
Ð
6 Press TIMER REC. The timer symbol ( ) will appear on the display and the VCR stands by for recording.
TIMER REC At the same time, VCR mode will change to DVD mode automatically.
You can use DVD even if the VCR is in the timer recording mode.
If you do not use the DVD, turn the power off.
Notes:
• The timer recording will start at 5 seconds before the time you predetermined.
• If the timer symbol( ) does not appear on the display in spite of the pressing of TIMER REC , the cassette may not have been loaded.
29
• If the cassette is ejected in spite of the pressing of TIMER
REC , the erase prevention tab of the cassette may have been removed.
29
3 Press SET + or – to select the date, then press
ENTER.
CH –
SET +
ENTER
SET –
CH +
DATE
26(SU)
START END CH
Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
á+/Ð/ENTER/CANCEL/MENUñ
Ð
Ð
Ð
Ð
Ð
Ð
Ð
Ð
4 Set the start time, end time, channel and tape speed as in step 3.
DATE START END CH
26(SU) 11:00 PM 11:30 PM 125 SLP
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð
Ð
Ð
Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
á+/Ð/ENTER/CANCEL/MENU ñ
Ð
Ð
Ð
Notes:
• Press CANCEL to move cursor backward for correction.
• To record from external source set the channel to “L1” or
“L2”.
Notes:
• If the timer symbol ( ) blinks when the timer recording ended, the TV program has not been completely recorded because of an insufficient tape length. Press TIMER REC to cancel the timer program or press EJECT to remove the cassette tape.
• During timer recording standby mode, the VCR mode cannot be operated. To use the VCR, press TIMER REC at first, then press
VCR DVD selector to change to VCR mode. After you use the
VCR, press TIMER REC again to put the VCR into timer recording standby mode.
• If you press TIMER REC during timer recording, the recording operation will be interrupted. If you press TIMER REC again within the programmed time, the recording operation will start again.
• After a power failure or disconnection of the power plug, all programmed recording settings and time display will be lost upon resumption of power. In this case, reset the clock 24 and reprogram any timer recording.
37
2C53601A (E)p32-37 37 3/10/04, 11:32
Recording (VCR)
Timer recording (continued)
VCR DVD
SET +/–
TIMER REC
VCR MENU
ENTER
CANCEL
To confirm or cancel a program
Weekly (e.g. WKL-TU: each Tuesday) or daily (e.g. MO-
SA: Monday to Saturday) Timer recording
Follow the procedure of timer recording on the previous page. At step 3 press SET + or – repeatedly until the desired setting appears. Then press ENTER .
When you press SET – repeatedly, the
DATE indicator will change as follows, in this case the day is Friday.
The current day (Friday) SU-SA (Sunday to Saturday)
1 If the Timer has been activated, press TIMER
REC to deactivate the Timer.
The timer symbol ( ) will disappear. Then press VCR DVD selector to change to VCR mode.
VCR
DVD TIMER REC
One month later minus one day
WKL-WE
(Weekly Wednesday)
SET +
CH – CH +
ENTER
SET –
MO-SA (Monday to Saturday)
MO-FR (Monday to Friday)
WKL-TH (Weekly Thursday)
DATE
WKL-WE
START END CH
2
CH –
To confirm Timer program:
At step 1 on the previous page select “TIMER REC
SET” and press ENTER .
The timer program list will appear on the screen.
SET +
ENTER
SET –
CH +
DATE START END CH
26(SU) 11:00 PM 11:30 PM 125 SLP
á
+/–/ENTER/CANCEL/MENU
ñ
á
+/–/ENTER/CANCEL/MENU
ñ
38
If the programs overlap another
3 To cancel Timer program:
Press SET + or – to select the unwanted program, then press CANCEL to cancel the program.
Do not overlap timer programs as portions of the conflicting programs will be lost. The first recording time has priority over the next recording time as shown in the diagram below.
Program 1
8 : 00 9 : 00 10 : 00 11 : 00
CH –
SET +
ENTER
SET –
CH +
CANCEL
DATE START END CH
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
Ð Ð Ð Ð Ð Ð Ð : Ð Ð Ð : Ð Ð Ð Ð Ð
á+/Ð/ENTER/CANCEL/MENUñ
Ð
Ð
Ð
Ð
Ð
Ð
Ð
Ð
Program 2
Program 3
Recording
Control Settings
Prog.1
Deleted Parts
Non Recorded Portion Parts
Prog.2
Prog.3
4 Press VCR MENU repeatedly until the menu screen is cleared.
VCR MENU
SETUP
Notes:
• The daily/weekly recording can be made continuously until the recording is canceled or the tape reaches the end.
• During timer recording the automatic rewinding mechanism does not function.
Notes:
• If there are other timer record programs remaining, TIMER
REC must be pressed to reactivate the timer, otherwise the remaining timer record programs will be ignored.
• You cannot confirm the Timer program during timer recording operation.
• You can correct or cancel a programmed setting in program confirm mode.
2C53601A (E)p38-41 38 3/10/04, 11:32
Other functions (VCR)
Stereo recording and playback /
Second Audio Program (SAP)
AUDIO SELECT
SET +/–
Stereo recording and playback
The VHS Hi-Fi audio system permits high fidelity recording of MTS STEREO TV broadcasts.
When a MTS STEREO broadcast is received, “STEREO” will appear on the screen for about 4 seconds and the program can be viewed or recorded in stereo.
The Hi-Fi stereo recording procedure is the same as for normal recordings.
STEREO
Note:
When using a CATV system, stereo TV programs may be transmitted over a mono cable channel. In this case
“STEREO” will not appear and the sound will be in mono.
AUDIO SELECT
AUDIO
VCR MENU
ENTER
CANCEL
Second Audio Program (SAP)
Your DVD/VCR is fitted with a SAP broadcast system which enables you to switch to a second audio program when viewing a selected channel.
This function applies only when the program is broadcast in multi-languages through the SAP broadcast system.
1 Press VCR MENU. Then press SET + or – to select “SAP”.
VCR MENU
SETUP
CH –
SET +
ENTER
CH +
MENU
TIMER REC SET
AUTO REPEAT ON OFF
SAP
CH SETUP
SYSTEM SETUP
ON OFF
SET –
á+/-/ENTER/MENU ñ
Output selection
When viewing an MTS stereo TV program, or playing a prerecorded VHS Hi-Fi stereo videotape, press AUDIO
SELECT to select how the audio will be heard through the speakers. Normally set to the Hi-Fi stereo position, this button can be set to the MONO position if the stereo broadcast or videotape audio is of poor quality. The “R” and “L” positions allow the audio from the Right or Left Hi-
Fi channel to be heard over both TV speakers. This button has no effect when viewing a MONO videotape or
TV program. Each time when you press the button,
OUTPUT SELECTION display appears on the screen for several seconds. Refer to the chart below.
OUTPUT
SELECTION
STEREO
L CH
R CH
MONO
SOUND HEARD ON BOTH
SPEAKERS
STEREO
LEFT CHANNEL AUDIO
RIGHT CHANNEL AUDIO
MONO
2 Press ENTER to select “ON”.
Then press VCR MENU until the menu screen is cleared.
SET +
CH –
ENTER
SET –
CH +
VCR MENU
SETUP
MENU
TIMER REC SET
AUTO REPEAT ON OFF
SAP
CH SETUP
SYSTEM SETUP
ON OFF
á+/-/ENTER/MENU ñ
Listening to SAP
When the VCR is turned on or a channel selection is made, make certain the letters “SAP” appears on the screen for about 4 seconds. This means that the “Second
Audio Program” broadcasting is available.
STEREO SAP SAP
OR
Notes:
• When playing back a tape that is not recorded in Hi-Fi stereo mode, the audio will automatically be monaural.
• When listening to a VHS Hi-Fi video tape or MTS broadcast through the VHF/UHF jack (Audio/Video cable not connected), the sound will be monaural.
39
3/10/04, 11:33 2C53601A (E)p38-41 39
Other functions (VCR)
Duplicating a video tape
If you connect the DVD/VCR to another VCR or Camcorder, you can duplicate
a previously recorded tape. Make all connections before turning on the power.
VCR DVD
2
1
4
5
Duplicating a video tape
Preparation:
• Turn ON the TV and select the corresponding video input.
• Press VCR DVD selector to select the VCR mode.
(The VCR indicator will light.)
• Load a cassette tape with the erase prevention tab intact.
• Load a previously recorded tape into the playback
VCR or Camcorder.
1 Press SP/SLP to select the desired tape speed
SP or SLP.
SP/SLP
PLAY MODE
It is recommended that you set the
tape speed to the SP mode on the
recording VCR for best results.
2 Press INPUT SELECT once or twice to select
AUDIO/VIDEO input position.
“L1” or “L2” will appear in the display.
INPUT SELECT
PROGESSIVE
Connection with second VCR
Playback VCR
To VIDEO OUT To AUDIO (R) OUT
To AUDIO (L) OUT
AUDIO/VIDEO cable (supplied)
Recording VCR
To VIDEO IN To AUDIO (R) IN
To AUDIO (L) IN
L1: on the rear panel
L2: on the front panel
3 Press PLAY on the playback VCR or Camcorder.
Connection with Camcorder
Playback Camcorder
To AV Jack
Recording VCR 4 Press REC/OTR on the recording VCR.
The duplicating process begins.
REC/OTR
5 Press STOP after duplicating a video tape.
To VIDEO IN
To AUDIO (R) IN
To AUDIO (L) IN
AUDIO/VIDEO cable (not supplied)
For duplicating a previously recorded tape from a camcorder, follow the camcorder manufacturer’s instructions. A typical camcorder dubbing hookup is shown above.
40
2C53601A (E)p38-41 40 3/10/04, 11:33
Recording a DVD/CD disc
You can record disc material in DVD, Audio CD, etc. onto a Video tape with this DVD/VCR.
2
1
4
3
5
Duplicating a DVD or CD disc
Preparation:
• Turn ON the TV and select the corresponding video input.
• Press VCR DVD selector to select the VCR mode.
(The VCR indicator will light.)
• Load a cassette tape with the erase prevention tab intact.
• Load a DVD/CD disc.
1 Press SP/SLP to select the desired tape speed
SP or SLP.
SP/SLP
PLAY MODE
Notes:
• You may not be able to record the beginning of the disc.
Begin VCR recording once program playback commences on the DVD.
• When the scanning mode is set to the progressive mode, you cannot duplicate a disc material onto a video tape.
When REC/OTR is pressed, the PROGRESSIVE indicator
“ ” on the display window will flash and “Please Set
Off” will appear on the screen.
• You can not record discs encoded with copy guard function. The following icon and text will show up on the
TV screen.
00 : 00 : 00 SP DISC IS COPY PROTECTED
2 Press VCR DVD selector to select the DVD mode.
The DVD indicator will light.
VCR
DVD
3 Press PLAY to start playback.
PLAY
4 Press REC/OTR to start recording.
REC/OTR
The DVD/VCR will change to the
VCR mode automatically and the playback picture or sound will be duplicated on the video cassette tape.
5 Press STOP if you finish recording.
If you wish to stop a DVD/CD disc, press VCR DVD selector to change the DVD mode, then press STOP .
41
2C53601A (E)p38-41 41 3/10/04, 11:33
Basic playback (DVD)
Playing a disc
This section shows you the basics on how to play a disc.
CAUTION
Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.
4 3, 5
Display window
2
STOP PLAY 1
DVD
VCD
CD
Basic playback
Preparations:
• When you want to view a disc, turn on the TV and select the corresponding video input connected to the DVD/VCR. This may include S-video or component video inputs which are exclusive to DVD playback.
• When you want to enjoy the sound of discs from the audio system, turn on the audio system and select the input connected to the DVD/VCR.
1
2
Press ON/STANDBY (I / ).
The DVD/VCR turns on.
Press VCR/DVD SELECT to select the DVD mode.
The DVD indicator will light.
5 Press OPEN/CLOSE or PLAY on the unit.
OR
The disc tray closes automatically.
On the TV-screen, “ ” changes to
“Reading” and then playback commences.
• A menu screen will appear on the TV screen, if the disc has a menu feature.
Reading
3 Press OPEN/CLOSE.
The disc tray opens.
6 Press / or / to select title.
SET +
CH – CH +
ENTER
SET –
4 Place the disc on the disc tray.
With the playback side down
7 Press ENTER.
SET +
• Title is selected and play commences.
CH – CH +
ENTER
SET –
• There are two different disc sizes. Place the disc in the correct guide on the disc tray. If the disc is out of the guide, it may damage the disc and cause the DVD/VCR to malfunction.
• Do not place a disc which is unplayable in this
DVD/VCR.
8 Press STOP to end playback.
• The unit records the stopped point, depending on the disc. “ ” appears on the screen. Press
PLAY to resume playback (from the scene point).
• If you press STOP again or unload the disc (“ ” appears on the screen.), the unit will clear the stopped point.
To start playback in the stop mode
Press PLAY .
42
2C53601A (E)p42-45 42 3/10/04, 11:33
VCR DVD
OPEN/CLOSE
PLAY
PAUSE/STILL
STOP
ENTER
To obtain a higher quality picture
Occasionally, some picture noise not usually visible during a normal broadcast may appear on the TV screen while playing a DVD video disc because the high resolution pictures on these discs include a lot of information. While the amount of noise depends on the TV you use with this DVD/VCR, you should generally reduce the sharpness adjustment on your TV when viewing DVD video discs.
About
The icons on the heading bar show the playable discs for the function described under that heading.
: You can use this function with DVD video discs.
: You can use this function with Video CDs.
: You can use this function with Audio CDs and CD-R/RW CDs.
To pause playback (still mode)
Press PAUSE/STILL during playback.
To stop playback
Press STOP .
To resume normal playback, press the PLAY button.
• The sound is muted during still mode.
To remove the disc
Press OPEN/CLOSE .
Remove the disc after the disc tray opens completely.
Playing a Disc while the VCR section is recording or standing by for timer recording
1) Start to record.
Follow steps 1~5 on page 34.
• If the DVD/VCR is standing by for recording, turn on the DVD/VCR.
2) Press VCR DVD selector to select DVD mode. The
DVD indicator will light.
3) Play a disc.
Follow steps 3 ~ 5 on page 42.
• Press PLAY if the DVD/VCR does not start to play a disc automatically.
4) Stop to play.
Press STOP to stop play back a disc.
Screen saver function
The screen saver operates when you leave the unit in
DVD stop mode for about five minutes.
The screen will repeatedly get dark gradually and back to normal.
To turn off the PBC
Press number button 1 in the stop mode, then press
ENTER.
Be sure to press the OPEN/CLOSE button to close the disc tray after you remove the disc.
Notes:
• If a non-compatible disc is loaded, “Incorrect Disc”, “Region Code Error” or “Parental Error” will appear on the TV screen according to the type of loaded disc. In this case, check your disc again (See pages 8 and 61).
• Some discs may take a minute or so to start playback.
• When you set a single-faced disc label downwards (ie. the wrong way up) and press the OPEN/CLOSE button or the PLAY button on the unit, “Reading” will appear on the display for 30 seconds and then “Incorrect Disc” will continue to be displayed.
• Some discs may not work the resuming facility.
• Resuming cannot function when you play a PBC-featured Video CD while the PBC is on. To turn off the PBC, see above.
• Some playback operations of DVDs may be intentionally fixed by software producers. Since this unit plays DVDs according to the disc contents the software producers designed, some playback features may not be available. Also refer to the instructions supplied with the DVDs.
• Do not move the DVD/VCR during playback. Doing so may damage the disc.
• Use the OPEN/CLOSE button to open and close the disc tray. Do not push the disc tray while it is moving. Doing so may cause the DVD/VCR to malfunction.
• Do not push up on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the DVD/VCR to malfunction.
• In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to press the
ON/STANDBY (I / ) button on your remote control once the movie is completed.
• There may be a slight delay between you pressing the button and the function activating.
43
2C53601A (E)p42-45 43 3/10/04, 11:33
Basic playback (DVD)
Playing a disc (continued)
You can play discs at various speeds.
REW
SKIP /
PLAY
FWD
PAUSE/STILL
SLOW
DVD
VCD
CD
Playing in fast reverse or fast forward directions
Press REW or FWD during playback.
To resume normal playback
Press PLAY .
PLAY
REW FWD
REW : Fast reverse playback
FWD : Fast forward playback
Each time you press the REW or
FWD button, the playback speed changes.
Notes:
• The DVD/VCR mutes sound and subtitles during reverse and forward scan of DVD video discs. However, the DVD/
VCR plays sound during fast forward or fast reverse play of audio CDs.
• The playback speed may differ depending on the disc.
DVD
VCD
Playing frame by frame
Press PAUSE/STILL during still playback.
Each time you press the PAUSE/
STILL button, the picture advances one frame.
To resume normal playback
Press PLAY .
PLAY
Note:
The sound is muted during frame by frame playback.
DVD
VCD
Playing in slow-motion
Press SLOW during playback.
SLOW Each time you press the SLOW button, the slow-motion speed changes.
To resume normal playback
Press PLAY .
PLAY
Note:
The sound is muted during slow-motion playback.
DVD
VCD
CD
Locating a chapter or track
Press SKIP or repeatedly to display the chapter or track number you want.
Playback starts from the selected chapter or track.
INDEX
SKIP
+ To locate succeeding chapters or tracks.
–
INDEX
SKIP
Playback starts from the beginning of the current chapter or track.
When you press twice in quick successions, playback starts from the beginning of the preceding chapter or track.
Notes:
• A “Prohibition” symbol may appear at the upper left of the screen. This symbol means either the feature you tried is not available on the disc, or the DVD/VCR can not access the feature at this time. This does not indicate a problem with the DVD/
VCR.
• The unit is capable of holding a still video image or On screen display image on your television screen indefinitely. If you leave the still video image or On screen display image displayed on your TV for an extended period of time, you risk permanent damage to your television screen. Projection televisions are very susceptible.
44
2C53601A (E)p42-45 44 3/10/04, 11:33
Advanced playback (DVD)
MP3/WMA/JPEG playback
This player can play back the MP3/WMA/JPEG-data which has been recorded on CD-R or CD-RW. To produce the MP3/WMA/JPEG-data, you need a
Windows-PC with CD-ROM drive and a MP3/WMA/JPEG-encoding Software
(not supplied).
The Apple-HFS-System can not be played.
OPEN/CLOSE
0–9
PLAY
STOP
ENTER
▲
/
▼
/ /
CD
MP3/WMA playback
1 Press OPEN/CLOSE.
The disc tray will open.
Place a disc on which MP3 or WMA files have been recorded onto the tray.
5 Press STOP to end playback.
PLAY
• The unit records the stopped point.
“ ” appears on the screen. Press
PLAY to resume playback (from the scene point).
• If you press STOP again or unload the disc, the unit will clear the stopped point.
2 Press OPEN/CLOSE or PLAY.
3
CH –
PLAY
The disc tray closes automatically.
On the TV-screen,“Reading” will appear.
Reading will take as much time as the number of file.
Reading
A file menu screen will appear on the TV screen.
Press or to select folder.
SET +
ENTER
SET –
CH +
6
7
4
5
1
2
3
CD-R
Pops
-/72 --:--
Japan
Bay Bridge
CLOSE MY EYES
DIVE TO BLUE
Honey
BLUE EYES
Blurry Eyes
8
9 flower
Lies and Truth-
10
11 winter fall
Rain
12 Strawberry
13 Welcome party
14 Thailand
/0-9/Enter/Play Mode
4 Press / or / or Number keys to select the desired file, then press ENTER.
The file is selected and play commences.
1
4
7
CH –
2
5
8
SET +
ENTER
SET –
3
6
9
CH +
• In case the folder includes more than
15 tracks, press or to display next file list.
-/72 --:--
6
7
4
5
1
2
3
CD-R
Pops
-/72 --:--
Japan
Bay Bridge
CLOSE MY EYES
DIVE TO BLUE
Honey
BLUE EYES
Blurry Eyes
8
9 flower
Lies and Truth-
10
11 winter fall
Rain
12 Strawberry
13 Welcome party
14 Thailand
/0-9/Enter/Play Mode
CD-R
Pops
15
16
Mother
Hold Your Last
/0-9/Enter/Play Mode
0
• When PLAY has been pressed after displaying the file menu, or when the disc tray has been closed after pressing
PLAY in step 2, playback begins automatically starting from the first file.
In this case, if the first file is an MP3/
WMA file, only MP3/WMA files are played back in order.
If the first file is a JPEG file, the first
JPEG file is played back.
MP3/WMA/JPEG CD Information
Limitations on MP3/WMA/JPEG CD playback
• MP3/WMA/JPEG CD is the disc that is standardized by
ISO9660, its file name must include 3-digits extension letters, “mp3”, “wma”, “jpg”.
• The directory and file names of the MP3/WMA/JPEG CD must be correspond to the ISO standardized files.
• This unit can read 200 files per disc. If a disc has more than
200 files, it reads up to 200 files, the remaining files will be omitted.
• The unit is able to recognize up to a maximum of 50 directories per disc.
• MP3/WMA CDs cannot be used for playback for the purpose of recording.
• If the CD has both audio tracks and MP3/WMA/JPEG files, only audio tracks are played.
• It may take more than one minute for this unit to read MP3/
WMA/JPEG files depending on its structure.
• Music recorded by “Joliet Recording Specification” can be played back, the file name is displayed (within 16 letters) on the screen. Long file names will be condensed.
• The music files recorded by “Hierarchical File System”
(HFS) cannot be played.
• The unit can play back baseline and progressive JPEG files.
Limitations on display
• The maximum number for display is 16 letters. Available letters for display are the following: capital or small alphabets of A through Z, numbers of 0 through 9, and _
(under score).
• Other letters than those above are replaced in hyphen.
Notes on MP3/WMA/JPEG files
To play back MP3/WMA/JPEG CD in the recorded order,
1. Use MP3/WMA/JPEG software that records data alphabetically or numerically.
2. Name each file including two-digit or three-digit number
(e.g. “01” “02” or “001” “002”).
3. Refrain from making too many sub-folders.
WMA disc compatibility with this player is limited as follows:
1) Sampling Frequency: within 32 -- 48 kHz
2) Bit Rate: within 48 -- 192kbps.
Mono WMA files and WMA files (under 48kbps) cannot be played back on this player.
CAUTION:
• Some MP3/WMA/JPEG CDs can not be played back depending on the recording conditions.
• The CD-R/RW that has no music data or non-MP3/WMA/
JPEG files can not be played back.
45
2C53601A (E)p42-45 45 3/10/04, 11:33
Advanced playback (DVD)
MP3/WMA/JPEG playback (continued)
You can select your desired JPEG file on the file menu and picture menu.
The selected JPEG file is automatically adjusted to the TV screen. (When the aspect ratio of the JPEG file is different to your TV screen, the black bar will appear at the top and bottom, or the both sides of the TV screen.
OPEN/CLOSE
0–9
SKIP /
PLAY
STOP
TOP MENU
MENU
ENTER
▲ / ▼ / /
JPEG CD playback
1 Press OPEN/CLOSE.
The disc tray will open.
Place a disc on which
JPEG files have been recorded onto the tray.
5 Press ENTER.
The selected picture appears on the TV screen.
SET +
CH – CH +
ENTER
SET –
2 Press OPEN/CLOSE or PLAY.
3 A file menu screen will appear on the TV screen.
Press or to select folder.
5
6
7
3
4
1
2
CD-R
Collection
-/36
Pic-1
Pic-2
Pic-3
Pic-4
Pic-5
Pic-6
Pic-7
8
9
10
11
Pic-8
Pic-9
Pic-10
Pic-11
12 Pic-12
13 Pic-13
14 Pic-14
/0-9/Enter/Play Mode/Menu
4
PLAY
The disc tray closes automatically.
On the TV-screen, “Reading” will appear.
Reading will take as much time as the number of file.
Reading
Press / or / or Number keys to select the desired file.
CD-R
Collection
-/36
CH –
SET +
ENTER
SET –
CH +
1
4
7
2
5
8
3
6
9 0
6
7
4
5
1
2
3
Pic-1
Pic-2
Pic-3
Pic-4
Pic-5
Pic-6
Pic-7
8
9
Pic-8
Pic-9
10
11
Pic-10
Pic-11
12 Pic-12
13 Pic-13
14 Pic-14
/0-9/Enter/Play Mode/Menu
To display a picture menu, press MENU.
(To return to a file menu, press TOP MENU.)
Press / or / to select the desired file.
MENU
6 Press STOP to end playback.
The file menu appears on the TV screen.
If you want to watch the other file, repeat steps 4~5.
Notes:
• The picture menu is displayed when the FUJICOLOR CD or the Kodak Picture CD are played. To display the file menu press TOP MENU .
• During MP3/WMA/JPEG-Playback, you can not use SEARCH,
A-B Repeat functions.
• You can use Repeat (Track or All), Random functions and
Program playback for MP3/WMA/JPEG CD Playback. (See pages 52 and 53.)
• In the case of a CD containing a mixture of MP3, WMA and
JPEG files, the files are played back by selecting them from the file menu.
File menu information
Operation
Media type File number
Elapsed time
Folder
TOP MENU
• To display next list, press SKIP or .
• When PLAY has been pressed after displaying the file menu, or when the disc tray has been closed after pressing PLAY in step 2, playback begins automatically starting from the first file. In this case, if the first file is a JPEG file, the first JPEG file is played back. If the first file is an MP3/WMA file, only MP3/WMA files are played back in order.
: Indicates MP3 file
: Indicates WMA file
: Indicates JPEG file
/Menu
Microsoft, Windows Media, and Windows Logo are trademarks or registered trademarks of Microsoft
Corporation in both the United States and other countries.
46
2C53601A (E)p46-47 46 3/10/04, 11:33
SETUP
ENTER
▲ / ▼ / /
Setting the JPEG Interval
You can continuously play back all JPEG files automatically.
After the setting below, start playing the disc on which JPEG files have been recorded.
1 Press SETUP in the stop mode. Press select “Picture”, then press ENTER.
VCR MENU
SETUP
Language Picture Sound
or
Parental Other
to
4 To make SETUP screen disappear, press SETUP.
VCR MENU
SETUP
SET +
CH –
ENTER
SET –
CH +
/Enter/Setup/Return
2
Press or to select “JPEG Interval”.
CH –
SET +
ENTER
SET –
CH +
Language Picture Sound Parental Other
E.B.L.
Tv Screen
Off
Display
JPEG Interval
On
Off
Select Files All
/Enter/Setup/Return
3
Press ENTER or / to select your desired time.
CH –
SET +
ENTER
SET –
CH +
Language Picture Sound Parental Other
E.B.L.
Off
Tv Screen
Display
JPEG Interval
On
5 Seconds
Select Files All
/Enter/Setup/Return
Off:
Plays back one file at a time.
5 Seconds:
Plays back images in the form of a slide show at 5 second intervals.
10 Seconds:
Plays back images in the form of a slide show at 10 second intervals.
15 Seconds:
Plays back images in the form of a slide show in 15 second intervals.
47
2C53601A (E)p46-47 47 3/10/04, 11:33
Advanced playback (DVD)
MP3/WMA/JPEG playback (continued)
SETUP
ENTER
▲ / ▼ / /
Setting the Select Files
When playing back a CD containing a mixture of MP3, WMA and JPEG files, only MP3/WMA or JPEG files can be displayed on the file menu.
1 Press SETUP in the stop mode.
Press or to select “Picture”, then press
ENTER.
VCR MENU
SETUP
Language Picture Sound Parental Other
4 To make SETUP screen disappear, press
SETUP.
VCR MENU
SETUP
SET +
CH –
ENTER
SET –
CH +
/Enter/Setup/Return
2
Press or to select “Select Files”.
SET +
CH –
ENTER
SET –
CH +
Language Picture Sound Parental Other
E.B.L.
Tv Screen
Display
Off
4:3
On
JPEG Interval Off
Select Files All
/Enter/Setup/Return
3 Press ENTER or / to select your desired file type.
SET +
CH –
ENTER
SET –
CH +
Language Picture Sound Parental Other
E.B.L.
Tv Screen
Display
Off
4:3
On
JPEG Interval Off
Select Files Pictures Only
/Enter/Setup/Return
All:
Displays all files.
Music Only:
Displays only MP3/WMA files.
Pictures Only:
Displays only JPEG files.
48
2C53601A (E)p48-49 48 3/10/04, 11:33
ANGLE
ZOOM
▲ / ▼ / /
Zooming (JPEG CD)
This unit will allow you to zoom in on the JPEG image.
1 Press ZOOM during playback.
CM SKIP
ZOOM
Enlarged JPEG images are displayed.
You can make the images even larger by repeatedly pressing ZOOM .
2 Press / / / to view a different part of the frame.
SET +
CH –
ENTER
SET –
CH +
You may move the frame from the centre position to UP, DOWN, LEFT or
RIGHT direction.
2 1
3 In the zoom mode press ZOOM repeatedly to return to a 1:1 view ( Off).
CM SKIP
ZOOM
Off 3
Changing angles (JPEG CD)
You can display JPEG images rotating at 90 degree intervals.
1 Press ANGLE during playback.
Images are rotated 90 degrees to the right.
COUNTER RESET
ANGLE
2 Press ANGLE repeatedly until the desired angle is selected.
Pressing ANGLE four times returns the image to its original angle.
COUNTER RESET
ANGLE • Images are displayed at the same angle until the disc is removed.
2C53601A (E)p48-49 49 3/10/04, 11:33
49
Advanced playback (DVD)
Zooming/Locating desired scene
DISPLAY
0–9
▲ / ▼ / /
JUMP
ZOOM
ENTER
CANCEL
DVD
VCD
Zooming
This unit will allow you to zoom in on the frame image. You can then make selections by switching the position of the frame.
1 Press ZOOM during playback.
CM SKIP
ZOOM
The centre part of the image will be zoomed in.
Each press of ZOOM will change the
ZOOM 1 (x 1.3), 2 (x 1.5) and 3
(x 2.0).
2 Press / / / to view a different part of the frame.
SET +
CH –
ENTER
SET –
CH +
You may move the frame from the centre position to UP, DOWN, LEFT or
RIGHT direction.
1
3 In the zoom mode press ZOOM repeatedly to return to a 1:1 view ( Off).
CM SKIP
ZOOM
Notes:
• You can select the Pause, Slow or Search playback in the zoom mode.
• Some discs may not respond to zoom feature.
DVD
VCD
CD
Locating desired scene
Use the title, chapter and time recorded on the disc to locate the desired point to play back.
To check the title, chapter and time, press DISPLAY .
Press JUMP during playback or stop mode.
1
ZERO RETURN
JUMP
Jump Time
Title
Chapter
/Enter/0 9/Cancel/Jump
3 Press Numbered buttons (0–9) to change the number.
1
4
7
2
5
8
3
6
9 0
• If you input a wrong number, press
CANCEL .
• Refer to the package supplied with the disc to check the numbers.
2
CH –
Press or to select the “Time”, “Title” or
“Chapter”.
SET +
ENTER
SET –
CH +
4 Press ENTER. Playback starts.
CH –
SET +
ENTER
SET –
CH +
• When you change the title, playback starts from Chapter 1 of the selected title.
• Some discs may not work in the above operation.
Note:
In case of the Video-CD playback with PBC, the JUMP does not work. To turn off PBC, see page 43 .
50
2C53601A (E)p50-53 50 3/10/04, 11:34
Marking desired scenes
The unit stores the points that you want to watch again up to 3 points.
You can resume playback from each scene.
DVD
VCD
CD
Marking the scenes
1 Press MARKER during playback.
MARKER
Marker 1
Marker 2
Marker 3
/Enter/Cancel/Marker
▲ / ▼
MARKER
ENTER
CANCEL
DVD
VCD
CD
Returning to the scenes
1 Press MARKER during playback or stop mode.
MARKER
Marker 1
Marker 2
00
01
27
16
Marker 3 02
/Enter/CancelMarker
08
54
25
31
2 Select the blank Marker using or .
Then press ENTER at the desired scene.
• Repeat this procedure to set the other 2 scenes.
SET + Marker 1
Marker 2
00
Marker 3
/Enter/Cancel/Marker
27 54
CH –
ENTER
SET –
CH +
3 Press MARKER to remove this display.
MARKER
2 Press or to select the Marker 1-3.
SET +
Marker 1
Marker 2
00
01
27
16
Marker 3 02
/Enter/Cancel/Marker
08
54
25
31
CH – CH +
ENTER
SET –
3 Press ENTER.
SET +
Playback starts from the marked scene.
CH –
ENTER
SET –
CH +
To cancel the Marker
Follow the above steps 1~2, then press CANCEL .
Notes:
•
•
• Some discs may not work with the marking operation.
The marking is canceled when you open the disc tray or turn the power off.
Some subtitles recorded around the marker may fail to appear.
3/10/04, 11:34
51
2C53601A (E)p50-53 51
Advanced playback (DVD)
Repeat playback/A-B Repeat playback
PLAY MODE
A-B RPT
DVD
VCD
CD
Repeat playback of Title, Chapter and Track
ENTER
▼ / /
DVD
VCD
CD
A-B Repeat playback
A-B repeat playback allows you to repeat material between two selected points.
Press PLAY MODE during playback or stop mode.
1
SP/SLP
PLAY MODE
1 Press A-B RPT during playback.
A-B RPT The start point is selected.
A
2 DVD
Press / or ENTER once or twice to select
“Chapter” or “Title”.
CH –
SET +
CH +
Repeat :
/Enter/Play Mode
Off
ENTER
SET –
Repeat :
/Enter/Play Mode
Chapter Repeat :
/Enter/Play Mode
Title
CH –
CD/VCD
Press to select “Repeat”.
Press / or ENTER once or twice to select
“Track” or “All”.
SET +
ENTER
SET –
CH +
Play Mode
Repeat
:
:
Off
Off
/Enter/Play Mode
Play Mode
Repeat
:
:
Off
Track
/Enter/Play Mode
Play Mode
Repeat
:
:
Off
All
/Enter/Play Mode
2 Press A-B RPT again.
A-B RPT The end point is selected. Playback starts at the point that you selected.
Playback stops at the end point, returns to Point A automatically, then starts again.
A B
3 Press PLAY MODE again to make the screen disappear.
Press PLAY to start Repeat playback.
To resume normal playback, select Repeat “Off”.
Note:
Some discs may not work with the repeat operation.
To resume normal playback
Press A-B RPT again.
A-B RPT “
Off
” appears on the screen.
Notes:
• In A-B repeat mode, subtitles near point A or B may not appear.
• A-B Repeat playback is not available in multi-angle scenes.
• A-B Repeat playback does not work when Repeat playback is on.
• You may not be able to set A-B Repeat, depending on the scenes of the DVD.
• A-B repeat does not work with an interactive DVD, MP3/
WMA/JPEG CD and Video CD with PBC.
52
2C53601A (E)p50-53 52 3/10/04, 11:34
Program playback/Random playback (CD)
You can arrange the order of tracks on the disc.
0–9
PLAY MODE
PLAY
▲ / ▼ / /
ENTER
CANCEL
VCD
CD
Program playback
Press PLAY MODE in the stop mode.
1
SP/SLP
PLAY MODE Play Mode
Repeat
:
:
Off
Off
/Enter/Play Mode
2 Press or to select Play Mode, then press
/ or ENTER to select “Program”.
CH –
SET +
ENTER
SET –
CH +
Play Mode
Repeat
1
2
3
Clear
4
5
6
: Program
: Off
7
8
10
11
9 12
Program Playback
/Enter/0 9/Cancel/Play Mode
4
CH –
Press / or / to select “Program
Playback” and press ENTER.
SET +
ENTER
SET –
CH +
The programmes you selected will start to playback in the order.
To return to normal playback, select
Play Mode: “Off”.
Play Mode
Repeat
1 7
2 3
4
5
3 1 1
Clear
: Program
: Off
7
8
10
11
6 9 12
Program Playback
/Enter/0 9/Cancel/Play Mode
3 Press / or / to select the programming position. Use Numbered buttons (0–9) to input the Track numbers.
SET +
• To program others, repeat Step 3.
• If you input a wrong number, press
CANCEL.
CH –
ENTER
SET –
CH +
1
4
7
2
5
8
3
6
9 0
Play Mode
Repeat
1 9
2 3
3 1 1
Clear
: Program
4
5
6
: Off
7 10
8
9
11
12
Program Playback
/Enter/0 9/Cancel/Play Mode
To cancel program playback
Select “Clear” and press ENTER .
CH –
SET +
ENTER
SET –
CH +
• The program is canceled when you open the disc tray or turn the power off.
Note:
In playing back the Video CD with PBC, you can not set
Program playback.
VCD
CD
Random playback
Press PLAY MODE in the stop mode.
1
SP/SLP
PLAY MODE
3 Press PLAY.
PLAY
The Random Playback will start.
2 Press / to select Play Mode, then press
/ to select “Random”.
SET +
Play Mode
Repeat
: Random
: Off
/Enter/Play Mode
CH –
ENTER
CH +
SET –
Note:
In playing back the Video CD with PBC, you can not set
Random playback.
53
2C53601A (E)p50-53 53 3/10/04, 11:34
Advanced playback (DVD)
Changing angles/Title selection/DVD menu
ANGLE
PLAY
TOP MENU
MENU
ENTER
▲ / ▼ / /
Changing angles
When playing back a disc recorded with multi-angle facility, you can change the angle that you are viewing the scene from.
1 Press ANGLE during playback.
The current angle will appear.
COUNTER RESET
ANGLE
1/9
2 Press ANGLE repeatedly until the desired angle is selected.
COUNTER RESET
ANGLE
Note:
Depending on the DVD, you may not be able to change the angles even if multi-angles are recorded on the DVD.
Title selection
Two or more titles are recorded on some discs. If the title menu is recorded on the disc, you can select the desired title.
1 Press TOP MENU during playback.
TOP MENU Title menu appears on the screen.
3 Press ENTER or PLAY.
SET +
The playback of the selected title will start.
CH – CH + PLAY
ENTER
SET –
2 Press / or / to select the desired title.
SET +
CH – CH +
ENTER
SET –
Note:
Depending on the DVD, you may not be able to select the title.
Depending on the DVD, a “title menu” may simply be called a
“menu” or “title” in the instructions supplied with the disc.
DVD menu
Some DVDs allow you to select the disc contents using the menu.
When you play back these DVDs, you can select the subtitle language and sound-track language, etc. using the menu.
1 Press MENU during playback.
MENU
The DVD menu appears on the screen.
• Press MENU again to resume playback at the scene when you pressed MENU .
3
CH –
Press ENTER.
SET +
ENTER
SET –
CH +
The menu continues to another screen. Repeat steps 2 and 3 to set the item completely.
2 Press / or / to select the desired item.
SET +
Note:
Depending on the DVD, you may not be able to resume playback from the scene point when you pressed MENU .
CH –
ENTER
SET –
CH +
54
2C53601A (E)p54-57 54 3/10/04, 11:34
Function setup (DVD)
Changing soundtrack language/
Setting surround sound
AUDIO
/
DVD
VCD
Changing soundtrack language
You can select the language when you play a multilingual disc.
1 Press AUDIO during playback.
AUDIO SELECT
AUDIO
The current soundtrack language will appear.
In case of Video CD playback
Audio type changes as follows each time you press AUDIO .
LR
Spatializer Off
L
Spatializer Off
R
Spatializer Off
2/8 Fra Dolby Digital
Spatializer Off
2 Press AUDIO repeatedly until the desired language is selected.
AUDIO SELECT
AUDIO
The on-screen display will disappear after a few seconds.
Notes:
• If the desired language is not heard after pressing the button several times, the language is not recorded on the disc.
• Changing soundtrack language is cancelled when you open the disc tray. The initial default language or available language will be heard if the disc is played back again.
DVD
VCD
CD
Setting surround sound
This DVD/VCR equipped with a “SPATIALIZER VIRTUAL SURROUND”. It can produce the effect of being in a cinema or a concert hall.
During disc playback press AUDIO.
1
AUDIO SELECT
AUDIO
1/8 Eng Dolby Digital
Spatializer Off
To cancel Surround mode :
Follow the left steps 1~2, then press or to select the
“Off” position.
Note:
The “SPATIALIZER VIRTUAL SURROUND” is effective only for the sound of disc.
Press or to select “On”.
2
SET +
CH –
ENTER
SET –
CH +
1/8 Eng Dolby Digital
Spatializer On
Spatializer ® 3-Dimensional Sound Processing provided by
Desper Products. Inc.
Certain audio features of this product manufactured under a license from Desper Products, Inc., Spatializer ® and the circle-in-square device are trademarks owned by Desper
Products, Inc.
55
2C53601A (E)p54-57 55 3/10/04, 11:34
Function setup (DVD)
Setting subtitles/Karaoke playback
SUBTITLE
AUDIO
▲ / ▼ / /
Turning the subtitles on and off
When playing back a disc recorded with subtitles, you can turn the subtitles on or off.
Press SUBTITLE during playback until “Off” appears.
ATR
SUBTITLE Off
Note:
Depending on the DVD, you may not be able to turn the subtitles on even if they are recorded on it.
Depending on the DVD, you may not be able to turn the subtitles off.
Changing the subtitle language
You can select the language when playing back a disc recorded with multi-lingual subtitles.
1
2
Press SUBTITLE repeatedly during playback until your desired language appears.
ATR
SUBTITLE
1/32 Eng
The on-screen display will disappear after a few seconds.
Notes:
• Changing subtitle language is cancelled when you open the disc tray.
• Depending on the DVD, you may not be able to change the subtitles even if multilingual subtitles are recorded on it. While playing the DVD, the subtitle may change when: -you open or close the disc tray -you change the title.
• In some cases, the subtitle language is not changed to the selected one immediately.
Karaoke playback
You can turn the vocal on or off recorded on the DVD KARAOKE.
1 During DVD KARAOKE disc playback, press
AUDIO.
AUDIO SELECT
AUDIO 1/8 Eng Dolby Digital
Spatializer Off
Notes:
• The vocal output feature is used during playback of
Dolby Digital (multi-channel) recorded DVD KARAOKE discs. This feature allows you to turn off vocal audio tracks, or restore them for background accompaniment.
• When playing Karaoke, connect appropriate audio equipment such as an amplifier to the DVD/VCR.
2 Press ▲ or ▼ until the KARAOKE symbol ( ) appears.
• If you play non-Karaoke disc, the KARAOKE symbol ( ) does not appear.
SET +
CH –
ENTER
SET –
CH +
1/8 Eng Dolby Digital
Off
56
3 Press or to select “On” or “Off”.
SET +
On : The primary vocal is output when it is recorded on the disc.
Off : The primary vocal is not output.
CH –
ENTER
CH +
SET –
2C53601A (E)p54-57 56 3/10/04, 11:34
E.B.L. (Enhanced Black Level)
To select the black level of playback pictures, set your preference and monitor’s ability.
SETUP
RETURN
ENTER
▲ / ▼ / /
Setting E.B.L.
1 Press SETUP in the stop mode or No Disc.
Press or to select “Picture”.
VCR MENU
SETUP Language Picture Sound Parental Other
4 To make SETUP screen disappear, press SETUP or RETURN while the SETUP screen is being displayed.
VCR MENU
SETUP
SET +
CH –
ENTER
SET –
CH +
/Enter/Setup/Return
RETURN
2 Press or ENTER, then press or to select
“E.B.L.”.
SET +
CH –
ENTER
SET –
CH +
Language Picture Sound Parental Other
E.B.L.
Tv Screen
Display
Off
4:3
On
Off JPEG Interval
Select Files All
/Enter/Setup/Return
3 Press / or ENTER to select “On” or “Off”.
CH –
SET +
ENTER
SET –
CH +
Language Picture Sound Parental Other
E.B.L.
Tv Screen
Display
On
4:3
On
JPEG Interval Off
Select Files All
/Enter/Setup/Return
On: Enhanced grey scale (0 IRE cut off)
Off: Standard grey scale (7.5 IRE cut off)
3/10/04, 11:34
57
2C53601A (E)p54-57 57
Function setup (DVD)
Setting the aspect ratio of TV screen
You can select the aspect ratio for your TV.
The following pages describe the setup/operation in DVD mode.
SETUP
RETURN
ENTER
▲ / ▼ / /
Setting the aspect ratio of TV screen
1 Press SETUP in the stop mode or No Disc.
Press or to select “Picture”.
CH –
VCR MENU
SETUP
SET +
ENTER
SET –
CH +
Language Picture Sound Parental Other
/Enter/Setup/Return
You have the following screen sizes to choose from:
4:3 Letter box:
Select this mode when connecting to a conventional TV.
When playing back a wide screen-DVD disc, it displays the wide picture with black bands at the top and bottom of screen.
4:3 Pan scan:
It displays the wide picture on the whole screen with left and right edges automatically cut off.
16:9 Wide:
Select this mode when connecting to a wide-screen TV.
A wide screen picture is displayed full size.
2 Press or ENTER, then press or to select
“Tv Screen”.
SET +
CH –
ENTER
SET –
CH +
Language Picture Sound Parental Other
E.B.L.
Tv Screen
Display
Off
4:3
On
Off JPEG Interval
Select Files All
/Enter/Setup/Return
4 To make SETUP screen disappear, press SETUP or RETURN while the SETUP screen is being displayed.
VCR MENU
SETUP
RETURN 3 Press or ENTER.
Press or to select your desired screen type, then press ENTER.
SET +
CH –
ENTER
SET –
CH +
Language Picture Sound Parental Other
E.B.L.
Tv Screen
Display
JPEG Interval
Off
4:3
On
Off
Select Files All
/Enter/Setup/Return
4:3
4:3
16:9
Note:
If the DVD disc is not formatted in the pan & scan style, it displays 4:3 style.
58
2C53601A (E)p58-61 58 3/10/04, 11:35
DISPLAY
Setting on screen display/Status display of disc
SETUP
RETURN
ENTER
▲ / ▼ / /
Setting on screen display
On screen display can be switched on or off when you press the buttons.
1 Press SETUP in the stop mode or No Disc.
Press or to select “Picture”.
VCR MENU
SETUP
Language Picture Sound Parental Other
SET +
/Enter/Setup/Return
3
CH –
Press / or ENTER to select “On” or “Off”.
SET +
ENTER
SET –
CH +
Language Picture Sound Parental Other
E.B.L.
Tv Screen
Display
JPEG Interval
Off
4:3
Off
Off
Select Files All
/Enter/Setup/Return
CH – CH +
ENTER
SET – On: On screen displays appear when you press the buttons (factory setting).
Off: On screen displays do not appear when you press any buttons.
2 Press or ENTER, then press or to select
“Display”.
SET +
CH –
ENTER
SET –
CH +
Language Picture Sound Parental Other
E.B.L.
Tv Screen
Display
Off
4:3
On
JPEG Interval
Select Files
Off
All
/Enter/Setup/Return
4 To make SETUP screen disappear, press SETUP or
RETURN while the SETUP screen is being displayed.
VCR MENU
SETUP
RETURN
DVD
VCD
CD
Status display of disc
Each press of DISPLAY, the status display of the disc will appear on the screen and change as follows.
DVD
00:34:56 01:12:33
Title
1/8
1/32
1/99
00:34:56 01:12:33
Chapter 1/999 1/9
Eng DolbyDigital
Eng
Video CD
00:12 04:32
Audio CD
Track 11/99
34:56 71:33
To make status display disappear, press DISPLAY again.
PBC
Track -/-
00:12 04:32
When you playback the CD disc, the status display will appear on the screen and continue displaying.
59
2C53601A (E)p58-61 59 3/10/04, 11:35
Function setup (DVD)
Dynamic Range Control
DRC (Dynamic Range Control) enables you to control the dynamic range so as to achieve a suitable sound for your equipment.
SETUP
RETURN
ENTER
▲
/
▼
/ /
Dynamic Range Control
1 Press SETUP in the stop mode.
Press or to select “Sound”.
VCR MENU
SETUP
Language Picture Sound Parental Other
4 To make SETUP screen disappear, press SETUP or RETURN while the SETUP screen is being displayed.
VCR MENU
SETUP
SET +
CH –
ENTER
SET –
CH +
/Enter/Setup/Return
RETURN
2 Press or ENTER to select “Dialogue”.
SET + Language Picture Sound Parental Other
Dialogue Off
CH – CH +
ENTER
SET –
/Enter/Setup/Return
Notes:
• This function works only during playback of Dolby Digital recorded discs.
• The level of Dynamic Range Reduction may differ depending on DVD video disc.
3 Press or ENTER, then press or to select desired setting.
SET +
Language Picture Sound Parental Other
Dialogue Off On : DRC(TV)
Off : DRC(Std)
CH –
ENTER
SET –
CH +
/Enter/Setup/Return
On: Loud sound such as explosion or the like is toned down slightly when played back. This makes it suitable for when it is connected to a stereo.
Off: It plays back at the recording level on the disc.
60
2C53601A (E)p58-61 60 3/10/04, 11:35
Parental control setting
Some discs are specified not suitable for children. Such discs can be limited not to play back with the unit.
0–9
▲ / ▼ / /
SETUP
RETURN
ENTER
CANCEL
Parental control setting
1 Press SETUP in the stop mode or No Disc.
Press or to select “Parental”. Then press
or ENTER.
VCR MENU
SETUP
Language Picture Sound Parental Other
Password
Parental Off
SET +
0 9/Cancel
/Enter/Setup/Return
CH – CH +
ENTER
SET –
4 Press ENTER to store the password.
SET +
Note: Now the rating is locked and the setting cannot be changed unless you enter the correct password.
CH – CH +
ENTER
SET –
Language Picture
Password
Parental
Sound Parental Other
1
0 9/Cancel
/Enter/Setup/Return
2 Press or to select “Parental”, then press
or until the level you require appears.
SET +
CH – CH +
Language Picture Sound Parental Other
Password
Parental 1
ENTER
SET –
5 Press SETUP or RETURN to remove the parental control screen.
VCR MENU
SETUP
RETURN
/Enter/Setup/Return
• Level Off: The parental control setting does not function.
• Level 8: All DVD software can be played back.
• Level 1: DVD software for adults cannot be played back.
• Select from the level 1 to level 8. The limitation will be more severe as the level number is lower.
3 Press or to select “Password”.
Press Number buttons (0-9) to input a 4-digit password.
SET + Language Picture Sound Parental Other
Password
Parental
1 2 3 4
1
CH –
ENTER
CH +
SET –
0 9/Cancel
/Enter/Setup/Return
1 2 3
4
7
5
8
6
9 0
Be sure to remember this number!
• If you input a wrong number, press CANCEL .
Notes:
• If each setup (pages 57~66) has been completed, the unit can always be worked under the same conditions (especially with DVD discs).
Each setup will be retained in the memory if you turn the power off.
• Depending on the discs, the unit cannot limit playback.
• Some discs may not be encoded with specific rating level information though its disc jacket says “adult.” For those discs, the age restriction will not work.
61
2C53601A (E)p58-61 61 3/10/04, 11:35
Function setup (DVD)
To change the parental level
OPEN/CLOSE
0–9
STOP
SETUP
RETURN
ENTER
▲ / ▼ / /
To change the parental level
1 Press SETUP in the stop mode or No Disc.
Press or to select “Parental”.
Then press or ENTER.
VCR MENU
SETUP
Language Picture Sound Parental Other
Password
Parental 1
SET +
0 9/Cancel
/Enter/Setup/Return
CH – CH +
ENTER
SET –
5 Press or to select “Password”, then press
Number buttons (0–9) to enter the password.
SET + Note: You can change the password if you want.
CH – CH +
ENTER
SET –
Language Picture Sound Parental Other
Password
Parental
9 8 7 6
5
1 2 3
4 5 6
0 9/Cancel
/Enter/Setup/Return
7 8 9 0
2 Press Number buttons (0–9) to enter the password you have stored.
1
4
2
5
3
6
Language Picture
Password
Parental
Sound
1 2 3 4
1
Parental Other
7 8 9 0
0 9/Cancel
/Enter/Setup/Return
6 Press ENTER.
CH –
SET +
ENTER
SET –
CH +
Now the parental level is changed and locked.
Language Picture
Password
Parental
Sound Parental Other
5
0 9/Cancel
/Enter/Setup/Return
3 Press ENTER.
The rating is now unlocked.
SET +
CH – CH +
Language Picture Sound Parental Other
Password
Parental 1
ENTER
SET –
0 9/Cancel
/Enter/Setup/Return
7 Press SETUP or RETURN to remove the parental control screen.
VCR MENU
SETUP
RETURN
4 Press or to select “Parental”, then press
or to change the parental level.
SET +
Language Picture Sound Parental Other
Password
Parental 5 CH –
ENTER
SET –
CH +
/Enter/Setup/Return
If you forget the password...
1. Press OPEN/CLOSE to open the disc tray.
2. Remove the disc.
3. Press OPEN/CLOSE again to close the disc tray.
“No Disc” appears on the screen.
4. While holding 7 down on the remote control, press
STOP on the front panel. “PASSWORD CLEAR” appears on the screen.
5. Enter a new password again.
62
2C53601A (E)p62-67 62 3/10/04, 11:35
Temporary disabling of rating level by DVD disc
Depending on the DVD disc, the disc may try to temporarily cancel the rating level that you have set.
It is up to you to decide whether to cancel the rating level or not.
OPEN/CLOSE
0–9
PLAY
▲ / ▼
RETURN
ENTER
Temporary disabling of rating level by DVD disc
1 Load a DVD disc and press PLAY or OPEN/
CLOSE on the unit 42 .
PLAY
4 Enter the password with Number buttons (0–9).
Then press ENTER.
1
4
2
5
3
6
If you interrupt the entering, press
RETURN .
7 8 9 0
Please enter the
SET +
CH – CH +
Enter/0 9/Cancel/Return
ENTER
SET –
2 If the DVD disc has been designed to temporarily cancel the Rating level, the screen which follows the “Reading” screen will change, depending on which disc is played. If you select “YES” with the
ENTER key, “Your disc exceeds the parental control level#.” screen will then appear.
Reading
Your disc exceeds the parental control level#.
Parental Control Level
Cancel Picture
/Enter/Return
5
RETURN
Playback will commence if the entered password was correct.
3
If you wish to cancel the set rating level temporarily, select “Parental Control Level” with or , then press ENTER. If the 4-digit password at step 2 on page 62 has been set, the password entering screen will appear as shown in step 4.
Alternatively, if the password has not been set, playback will commence. If you don’t know (or have forgotten) the password, select “Cancel Picture”.
The setting screen will disappear. Press OPEN/
CLOSE to remove the disc.
Note:
This temporary cancellation of rating level will be kept until the disc is ejected.
When the disc is ejected, the original rating level will be set again automatically.
SET +
CH –
ENTER
SET –
CH +
63
2C53601A (E)p62-67 63 3/10/04, 11:35
Function setup (DVD)
Setting OSD language
The setup language can be selected.
SETUP
RETURN
ENTER
▲ / ▼ / /
DVD
VCD
CD
Setting OSD language
1 Press SETUP in the stop mode or NO DISC.
Press or to select “Other”.
VCR MENU
SETUP
Language Picture Sound Parental Other
SET +
CH –
ENTER
SET –
CH +
/Enter/Setup/Return
4 To make SETUP screen disappear, press SETUP or RETURN while the SETUP screen is being displayed.
VCR MENU
SETUP
RETURN
2 Press or ENTER to select “OSD Language”.
SET +
Language Picture Sound Parental Other
OSD Language English
CH – CH +
ENTER
SET –
If the unit does not operate properly: Static electricity, etc., may affect the player's operation. Disconnect the
AC power cord once, then connect it again.
/Enter/Setup/Return
3 Press or ENTER and then press or to select desired language (e.g. English), then press ENTER.
SET +
CH –
ENTER
SET –
CH +
Language Picture Sound Parental Other
OSD Language English English
Francais
Espanol
/Enter/Setup/Return
64
2C53601A (E)p62-67 64 3/10/04, 11:35
Setting language
You can select the language of “Menu”, “Subtitle” and “Audio” if their languages are recorded onto the disc more than one language.
SETUP
RETURN
ENTER
▲ / ▼ / /
Setting language
1 Press SETUP in the stop mode or No Disc.
Press or to select “Language”.
VCR MENU
SETUP
Language Picture Sound Parental Other
4 To make SETUP screen disappear, press SETUP or RETURN while the SETUP screen is being displayed.
VCR MENU
SETUP
SET +
CH –
ENTER
SET –
CH + /Enter/Setup/Return
RETURN
2 Press or ENTER, then press or to select desired langugage item.
SET +
CH –
ENTER
SET –
CH +
Language Picture Sound Parental Other
Menu
Subtitle
Audio
English
Automatic
English
Note:
If the selected language is not recorded on the disc, the firstpriority language is selected.
/Enter/Setup/Return
3 Press or ENTER.
Press or to select your desired language, then press ENTER.
SET +
CH –
ENTER
SET –
CH +
Language Picture Sound Parental Other
Menu
Subtitle
Audio
English
Automatic
English
English
Francais
Espanol
Other
/Enter/Setup/Return
English, Francais, Espanol:
The selected language will be heard or seen.
Other:
Other language can be selected (see “Language code list” on page 67).
Original: (Audio)
The unit will select the first priority language of each disc.
Automatic: (Subtitle)
• The unit will automatically select the same language in the AUDIO setting.
• When the unit selects the same language as the AUDIO, the subtitles will not appear during playback.
• When you do not use the same language as the AUDIO, the subtitles will appear during playback.
Off: (Subtitle)
Subtitles do not appear.
65
2C53601A (E)p62-67 65 3/10/04, 11:35
Function setup (DVD)
Selecting PROGRESSIVE scan
The progressive scan capability provides the highest resolution pictures with less flicker and line structure.
If you are using the Component video jacks, but are connecting the DVD/VCR to a standard (analog) television, set PROGRESSIVE to Off.
If you are using the Component video jacks for connection to a TV or monitor that is compatible with a progressive scan signal, set PROGRESSIVE to On.
VCR DVD
1
2
DVD
VCD
CD
Selecting PROGRESSIVE scan
Preparation:
• Connect to a TV equipped with component jacks.
• Turn ON the TV and set it to the corresponding video input mode.
• Set the S-VIDEO/COMPONENT video selector switch on the rear panel to COMPONENT position.
• Press VCR DVD selector to select the DVD mode. (The
DVD indicator will light.)
1
Press PROGRESSIVE in the stop mode.
INPUT SELECT
PROGESSIVE
The progressive indicator “ ” on the display window will light.
• The unit recognizes the picture source (film or video) of the current disc according to the disc information.
2
Press PLAY to start playback.
PLAY
There are two types of source content in pictures recorded in
DVD video discs: film content (pictures recorded from films at 24 frames per second) and video content (video signals recorded at 30 frames per second).
When the unit plays back a film source material, uninterlaced progressive output signals are created using the original information. When a video content is played back, the unit interleaves lines between the interlaced lines on each to create the interpolated picture and outputs as the progressive signal.
To select PROGRESSIVE scan Off
Press PROGRESSIVE in the stop mode.
The progressive indicator “ ” on the display window will go off.
Notes:
• Some discs may not be played back with the progressive scanning mode correctly because of the disc characteristics or recording condition.
• If your TV does not accept the progressive scan format, the picture will appear scrambled if you select progressive scan output from the unit. In such a case, select PROGRESSIVE scan Off.
• Once PROGRESSIVE scan On, all other video outputs are disabled except component video outputs.
• You cannot make the progressive scanning mode active in following cases.
– The unit is in the VCR mode.
– The disc is played back in the DVD mode.
– The S-VIDEO/COMPONENT video selector switch is set to
S-VIDEO position.
66
2C53601A (E)p62-67 66 3/10/04, 11:35
Others
Language code list
Enter the appropriate code number for the initial settings “Menu”, “Subtitle” and/or “Audio”
65
.
Language Name Code Language Name Code Language Name Code Language Name Code
Abkhazian
Afar
Afrikaans
Albanian
1112
1111
1116
2927
Fiji
Finnish
French
Frisian
1620 Lingala
1619 Lithuanian
1635 Malagasy
2224 Singhalese 2919
2230 Slovak
1628 Macedonian 2321 Slovenian
2317 Somali
2921
2922
2925
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
1123
1128
1835
1129
1135
1136
1211
1531
Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
Hausa
1722
2111
1415
1522
2122
1724
1731
1811
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
2329 Spanish 1529
2322 Sundanese 2931
2330 Swahili
2319 Swedish
2328 Tagalog
2325 Tajik
2324 Tamil
2411 Tatar
2933
2932
3022
3017
3011
3030
Catalan
Chinese
Corsican
Croatian
Czech
Danish
Dutch
English
Bengali; Bangla 1224 Hebrew
Bhutani 1436 Hindi
Bihari
Breton
1218
1228
Hungarian
Icelandic
Bulgarian
Burmese
1217 Indonesian
2335 Interlingua
Byelorussian 1215 Irish
Cambodian 2123 Italian
Esperanto
Estonian
Faroese
1311
3618
1325
1828
1329
1411
2422
1524
1525
1530
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kirghiz
Korean
Kurdish
Laothian
Latin
1933 Nepali
1819 Norwegian
1831 Oriya
1929 Panjabi
2124 Romanian
2129 Russian
2121 Samoan
2135 Sanskrit
2831 Vietnamese 3219
2125 Scots Gaelic 1714 Wolof
2131 Serbian 2928 Xhosa
2225
2211 Shona
1625 Latvian, Lettish 2232 Sindhi
2415 Telugu
2425 Thai
2528 Tibetan
2611 Tigrinya
1924 Pashto, Pushto 2629 Tonga
1911 Persian
1711 Polish
1930 Portuguese
2011 Quechua
1611
2622
2630
2731 Ukrainian
2825
2923 Volapük
2911 Welsh
Serbo-Croatian 2918
2924
2914
Turkish
Turkmen
Twi
2033 Rhaeto-Romance2823 Urdu
Uzbek
Yiddish
Yoruba
Zulu
3121
3128
3136
3225
1335
3325
3418
2019
3525
3631
3015
3018
1225
3019
3025
3028
3021
3033
67
2C53601A (E)p62-67 67 3/10/04, 11:35
Others
Troubleshooting
Check the following guide for the possible cause of a problem before contacting service.
DVD/VCR
SYMPTOMS POSSIBLE SOLUTIONS
DVD/VCR does not operate.
No picture.
No sound.
The remote control does not function.
No CATV reception.
• Make sure the power cord is plugged in.
• Try another AC outlet.
• Power is off, check fuse or circuit breaker.
• Unplug unit, then plug it back in.
• Select the DVD or VCR mode before operating.
• Antenna connection is not correct or antenna cable is disconnected.
• The video channel is not in the correct position or the TV is not set to the video channel 3 or 4.
• Check the unit is connected correctly.
• The video input selector of the TV is not set to VIDEO. Set to VIDEO (or equivalent).
• Channel is set to the external mode.
• Check the unit is connected correctly.
• Check the input selector of the amplifier is set properly.
• The unit is in the Special playback mode.
• Aim the remote control at the remote sensor.
• Operate within Approx. 7 Meters or reduce the light in the room.
• Clear the path of the beam.
• The batteries are weak. Replace the batteries.
• Check the batteries are inserted correctly.
• Check all CATV connections.
• Station or CATV system problems, try another station.
VCR
TV recording does not work.
Timer recording does not work.
Noise bars on screen.
• The erase prevention tab of the video cassette is broken off.
• The unit is in the external input mode.
• The time is not set correctly.
• The recording start/end time is not set correctly.
• The TIMER REC has not been pressed ( is not lit).
• Tracking adjustment beyond range of automatic tracking circuit. Try Manual tracking adjustment.
• Video heads are dirty.
• The tape is worn or damaged.
DVD
Display is not shown in your language.
Playback doesn’t start.
• Select proper language in the menu options.
• No disc is inserted.
• The disc may be dirty. Clean up the disc.
• The unit cannot play DVD-ROMs, etc.
Stopping playback, slow-motion play, repeat play, or memory play, etc. cannot be performed.
• Some discs may not do some of the functions.
No picture, or the screen is blurred or divided into two parts.
No 4:3 (16:9) picture.
No on-screen display.
No surround sound.
The unit or remote operation key is not functioning.
Playback does not start when the title is selected.
Audio soundtrack and/or subtitle language is not changed when you play back a DVD.
• The S-VIDEO/COMPONENT selector is not set correctly.
• The PROGRESSIVE scan is On through the unit is connected to a TV via the VIDEO OUT or the S-VIDEO OUT jack.
• The setup does not match your TV.
• Select Display “On”.
• The setup does not match your stereo system.
• Turn off the unit and unplug the AC power cord for several minutes, then replug it.
• Check the Parental setup.
• Multilingual language is not recorded on the DVD disc.
No subtitle.
Angle cannot be changed.
• Some discs have no subtitles.
• Subtitles are cleared. Press SUBTITLE.
• Multi-angles are not recorded on the DVD disc.
appears on the screen.
• The function is prohibited with the unit or the disc.
PAGE
–
5
5
–
30,42
14~17
22
14~19
–
–
14~19
–
31,44
13
16,17
29,34
64
42
6
8
–
19
66
61,62
65
56
54
44
24
37
37
31
31
–
58
59
20
–
68
2C53601A (E)p68-BACK 68 3/10/04, 11:35
Specifications
General
Power supply
Power consumption
Weight
Dimensions
Tuner
Antenna input/output
RF channel output
Color system
Video head
Audio track
Hi-Fi frequency response
Hi-Fi dynamic range
F.FWD/REW time at 25˚C (77˚F)
Applicable disc
Frequency range
S/N ratio
Harmonic distortion
Wow and flutter
Operating conditions
Input/Output
AC 120 V 60 Hz
Operation: 18 W, Stand by: 2 W
7.9 lbs (3.6 kg)
Width: 16-15/16 inches (430 mm)
Height: 3-7/8 inches (99 mm)
Depth: 9-13/16 inches (250.5 mm)
181 channel freq. synthesized
VHF
UHF
2-13
14-69
CATV 125 Channels
UHF/VHF In/Out: 75
Ω coaxial
Channel 3 or 4, Switchable
NTSC
4 Rotary heads
Hi-Fi sound - 2 Tracks / MONO sound - 1 Track
20 Hz to 20,000 Hz
More than 90dB
Approx. 1 minute and 48 seconds (with T-120 Cassette Tape)
DVD (12 cm, 8 cm), CD (12 cm, 8 cm)
DVD: 4 Hz-22 kHz, CD: 4 Hz-20 kHz
90dB (DVD)
0.02% (DVD)
Less than 0.01% Wrms
Temperature: 5˚C-40˚C (41˚F-104˚F), Operating status: Horizontal
DVD/VCR
Video input
Video output
Audio input
Audio output
1.0 V (p-p), 75
Ω
, negative sync., pin jack x 2
1.0 V (p-p), 75
Ω
, negative sync., pin jack x 1
–8 dBm, 50 k
Ω
, negative sync., pin jack (L/R) x 2
–8 dBm, 1 k
Ω
, negative sync., pin jack (L/R) x 1
DVD
S-video output
Component video output
Audio output (BITSTREAM/PCM
(Y) 1.0 V (p-p), 75
Ω
, negative sync., Mini DIN 4-pin
×
1
(C) 0.286 V (p-p), 75
Ω
(Y) 1.0 V (p-p), 75
Ω
, negative sync., pin jack
×
1
(P
B
)/(P
R
) 0.7 V (p-p), 75
Ω
, pin jack
×
2
0.5 V (p-p), 75
Ω
, pin jack
×
1
COAXIAL)
Audio output (BITSTREAM/PCM
OPTICAL)
Optical connector
×
1
Audio output (ANALOG) –12 dB, 1 k
Ω
, pin jacks (L, R)
×
1
S-VIDEO/COMPONENT video selector Slide switch
×
1
Supplied accessories
Audio/video cable ................................................. 1
Remote control (SE-R0108) ................................. 1
Batteries (R03/AAA) ............................................. 2
75 ohm coaxial cable ............................................ 1
• Designs and specifications are subject to change without notice.
3/10/04, 11:35
69
2C53601A (E)p68-BACK 69
Others
Limited warranty
70
2C53601A (E)p68-BACK 70 3/10/04, 11:36
2C53601A (E)p68-BACK 71 3/10/04, 11:36
71
04/04 U
2C53601A (E)p68-BACK 72 3/10/04, 11:36
Printed in Thailand
REPRODUCTOR DE DVD & VIDEOGRABADOR DE CASSETTE
SD-V396SU
Referencìa rápida
1
ALL
DIGITAL VIDEO
PRECAUCION
RIESGO DE DESCARGA
ELECTRICA NO ABRIR
AVISO:
PARA REDUCIR EL RIESGO DE DESCARGA
ELECTRICA, NO RETIRE LA CUBIERTA (O POSTE-
RIOR). EN EL INTERIOR DEL APARATO NO HAY
COMPONENTE ALGUNO QUE PRECISE SERVICIO DE
MANTENIMIENTO A CARGO DEL USUARIO. SOLICITE
CUALQUIER OPERACION DE MANTENIMIENTO A
PERSONAL DE SERVICIO CALIFICADO.
El símbolo del rayo dentro de un triángulo equilátero tiene por finalidad alertar al usuario acerca de la presencia de tensión peligrosa (sin aislación) en el interior del producto, que puede tener la intensidad suficiente como para constituir un riesgo de descarga eléctrica.
El signo de exclamación dentro de un triángulo equilátero tiene por finalidad alertar al usuario de impor tantes instrucciones de operación y mantenimiento (servicio) en la literatura que acompaña a este aparato.
AVISO: Para reducir el riesgo de incendio o descarga eléctrica, no exponga esta unidad a la lluvia ni a la humedad.
ADVERTENCIA: Este equipo ha sido sometido a pruebas y cumple con los límites establecidos para un aparato digital de Clase B, de acuerdo con la Parte 15 del Reglamento de la FCC. Estos límites están diseñados para proporcionar protección razonable contra interferencias perjudiciales en una instalación residencial.
Este equipo genera o emplea energía de radiofrecuencia y, si no es instalado y empleado de acuerdo con estas instrucciones, puede causar interferencias perjudiciales a las radiocomunicaciones.
Sin embargo, no garantizamos que no ocurrirán interferencias en una instalación en particular. Si este equipo causa interferencias perjudiciales a la recepción radial o televisiva, situación que puede ser determinada apagando y encendiendo el equipo, se sugiere al usuario que trate de corregir tal interferencia mediante una o más de las siguientes medidas:
- Reorientar o relocalizar la antena receptora.
- Incrementar la separación entre el equipo y el receptor.
- Conectar el equipo a un tomacorriente o circuito diferente al que está conectado al receptor.
- Consultar con el concesionario o un técnico experimentado solicitándole su asistencia.
PRECAUCION: El usuario corre el riesgo de perder la autorización para hacer funcionar este equipo en caso de que ejecute un cambio o modificación no aprobado por la parte responsable para la conformidad con las
Reglas FCC.
PRECAUCION:
ESTE TOCADISCOS DE VIDEO DIGITAL UTILIZA UN SISTEMA LASER.
PARA UTILIZAR CORRECTAMENTE ESTE PRODUCTO, LEA CUIDADOSAMENTE ESTE MANUAL DE INSTRUCCIONES Y
GUARDELO PARA SU REFERENCIA EN EL FUTURO. SI FUERA NECESARIO HACER UN MANTENIMIENTO DE ESTE
APARATO, CONSULTE CON UN CENTRO DE SERVICIO AUTORIZADO-LEA EL PROCEDIMIENTO DE SERVICIO.
EL USO DE LOS CONTROLES, AJUSTES O LA REALIZACION DE OTROS PROCEDIMIENTOS QUE NO SEAN LOS
ESPECIFICADOS AQUI PUEDE PROVOCAR UNA EXPOSICION A RADIACIONES PELIGROSAS.
PARA EVITAR LA EXPOSICION DIRECTA A LOS RAYOS LASER, NO TRATE DE ABRIR LA CAJA. PUEDE HABER UNA
RADIACION LASER VISIBLE AL ABRIR LA CAJA.
NO MIRE HACIA EL RAYO.
©2004 Toshiba Corporation
Este dispositivo no graba en cinta DVDs protegidos contra copias.
2C53607A (SP) Q Sheet 1 11/3/04, 6:31
INSTRUCCIONES IMPORTANTES
1. LEA LAS INSTRUCCIONES
Antes de usar la unidad, lea detenidamente todas las instrucciones de seguridad y operación.
2. CONSERVE ESTE MANUAL DE INSTRUCCIONES
Conserve las instrucciones de seguridad y operación para consultas futuras.
3. RESPETE LAS ADVERTENCIAS
Observe estrictamente todas las advertencias impresas en la unidad y las incluidas en el manual de instrucciones.
4. SIGA LAS INSTRUCCIONES
Siga todas las instrucciones de operación y uso.
5. LIMPIEZA
Antes de limpiar este videograbador, desconéctelo del tomacorriente mural. No use limpiadores líquidos ni aerosol. Utilice sólo un paño húmedo para limpiar el exterior del mueble.
6. ENCHUFES
El fabricante de esta unidad no hace ninguna recomendación de accesorios ya que pueden ser peligrosos.
7. AGUA Y HUMEDAD
No utilice este aparato cerca del agua. Por ejemplo cerca de una bañera, lavabo, pileta de la cocina, lavadero, en un sótano húmedo o cerca de una piscina.
8. ACCESORIOS
No instale esta unidad en un carro, soporte, trípode o mesa inestables. La unidad podría caerse, causando serias lesiones, resultando también severamente dañada a la unidad.
8A.
La combinación de aparato y carro deberá ser movida con cuidado. Las detenciones bruscas, la fuerza excesiva y las superficies disparejas podrán hacer que el aparato y el carro se vuelven.
9. VENTILACION
Las ranuras y aberturas en la parte trasera o inferior del mueble son para ventilación permiten un funcionamiento fiable de la unidad, protegiendo contra calentamiento excesivo. Estas aberturas no deberán ser bloqueadas ni cubiertas.
Para evitar bloquear las aberturas, nunca sitúe la unidad encima de una cama, sofá, alfombra u otra superficie similar. Tampoco instale la unidad cerca o encima de un radiador o calefactor. La unidad no deberá ser instalado en un mueble empotrado, como ser una repisa para libros o bastidor, a menos que se pueda garantizar una ventilación adecuada, y/o cuando las instrucciones del fabricante así lo especifiquen.
10. FUENTES DE ALIMENTACION
Esta unidad sólo deberá ser operada mediante el tipo de fuente de alimentación especificado en la etiqueta indicadora. Si no está seguro del tipo de fuente de alimentación que tiene en su casa, consulte a su distribuidor o a la compañía de electricidad local. En el caso de unidades diseñadas para funcionar a pilas o con otras fuentes de alimentación, consulte el manual de instrucciones respectivo.
11. CONEXIÓN A TIERRA O POLARIZACION
Esta unidad está equipada con una clavija polarizada de corriente alterna (una clavija que tiene una espiga más ancha que la otra). Esta clavija solamente puede ser insertada en el tomacorriente en una sola dirección. Esta es una medida de seguridad. Si no pudiera insertar completamente la clavija en el tomacorriente, vuelva a intentarlo invirtiendo la clavija. Si aún no fuera posible insertar la clavija, tome contacto con un electricista para que reemplace su tomacorriente obsoleto. En lugar de la clavija polarizada de corriente alterna, su unidad puede estar equipada con una clavija de conexión a tierra de 3 alambres
(una clavija con una tercera espiga de conexión a tierra). Este tipo de clavija sólo puede ser insertado en un tomacorriente con contacto a tierra. Esto también es una medida de seguridad. Si no pudiera insertar la clavija en el tomacorriente, tome contacto con un electricista para que reemplace su tomacorriente obsoleto.
No modifique las características de seguridad de la clavija de conexión a tierra.
12. PROTECCION DEL CABLE DE ALIMENTACION
Los cables de alimentación deberán ser tendidos de manera tal que la probabilidad de que sean pisados o aplastados por otros objetos sea mínima. Preste especial atención a las clavijas de los cables, a los receptáculos, y al punto por donde salen del aparato.
13. TORMENTAS ELECTRICAS
Como medida de protección durante tormentas eléctricas, o cuando el videograbador permanezca sin uso durante períodos prolongados de tiempo, desconéctelo del tomacorriente mural y desconecte la antena o el sistema de cable. Esto evitará que la unidad resulte dañada por tormentas eléctricas o sobretensiones en la línea de alimentación.
14. LINEAS DE ALIMENTACION
Un sistema de antena exterior no debería situarse cerca de líneas de alimentación aéreas ni de otros circuitos de luz eléctrica o potencia, o donde pueda caerse o entrar en contacto con tales líneas o circuitos de alimentación. Al instalar un sistema de antena exterior, tenga mucho cuidado de no tocar tales líneas o circuitos de alimentación, ya que el contacto con ellos podría ser fatal.
15. SOBRECARGA
No sobrecargue los tomacorrientes murales ni los cables de extensión, ya que esto podría causar incendios o descargas eléctricas.
16. ENTRADA DE OBJETOS Y LIQUIDOS
Nunca introduzca objetos de ningún tipo por las aberturas de la unidad, ya que podría tocar peligrosos puntos de alta tensión o piezas de cortocircuito, provocando incendios o descargas eléctricas. Nunca derrame ni rocíe ningún tipo de líquido sobre la unidad.
17. CONEXION A TIERRA DE LA ANTENA EXTERIOR
Si se conecta una antena externa o sistema de cable a la unidad, cerciórese de que el sistema de antena o cable está conectado a tierra para darle protección contra sobretensión y acumulación de carga estática. La Sección 810 del Código
Nacional de Electricidad, ANSI/NFPA 70, entrega información acerca de la manera correcta de conectar a tierra el mástil y la estructura soportante, puesta a tierra del alambre de entrada a una unidad de descarga de antena, tamaño de los conductores de puesta a tierra, ubicación de la nidad de descarga de la antena, conexión a los electrodos de tierra, y requisitos para el electrodo de tierra.
18. SERVICIO
No intente reparar la unidad usted mismo; al abrir o retirar las cubiertas usted se expondrá a alta tensión y a otros peligros. Solicite todo servicio a personal calificado.
Ejemplo: a. Cuando el cable de alimentación o la clavija estén dañados.
b. Si se ha derramado líquido sobre la unidad, o si algún objeto ha caído dentro del videograbador.
c. Si la unidad ha sido expuesta a la lluvia o al agua.
d. Cuando a pesar de haber seguido las instrucciones de operación, la unidad no funcione normalmente.
Ajuste solamente los controles indicados en el manual de instrucciones;el ajuste incorrecto de otros controles podrá causar daños a la unidad, la que por lo general requerirá de un prolongado trabajo de reparación (por un técnico calificado) para que sus condiciones normales de operación puedan ser restablecidas.
e. Si la unidad se ha caída o si el gabinete se ha dañado.
f . Cuando la unidad muestre un cambio notorio en su rendimiento.
19. PIEZAS DE REPUESTO
Cuando sea necesario reemplazar piezas, asegúrese de que el técnico de servicio emplee las piezas de repuesto especificadas por el fabricante, o piezas que tengan las mismas características que las piezas originales. Los cambios no autorizados podrán causar incendios, descargas eléctricas y otros problemas.
20. REVISION DE SEGURIDAD
Al finalizar cualquier servicio de mantenimiento o reparación de esta unidad, solicítele al técnico que efectúe comprobaciones de seguridad para determinar si el videograbador se encuentra o no en condiciones óptimas de operación.
21. CALOR
El producto debe ser situado lejos de fuente de calor como radiadores, reguladores de calefacción, estufas o otros productos (incluyendo amplificadores) que se producen calor.
22. BANDEJA DEL DISCO
No acerque sus dedos a la bandeja del disco cuando se está cerrando. Puede recibir heridas graves.
23. CONEXION
Cuando conecte el producto a otro equipo, desconecte la alimentación y desenchufe todos los equipos del tomacorriente. Si no lo hace, puede provocar una descarga eléctrica y heridas graves.
Lea cuidadosamente el manual de instrucciones del otro equipo y respete las instrucciones al hacer las conexiones.
24. RAYO LASER
No mire por la ranura de la bandeja del disco por las salidas de circulación de aire del producto para ver la fuente del rayo láser. Puede dañar sus ojos.
25. DISCO
No utilice un disco rayado, deformado o reparado. Estos discos se pueden romper fácilmente y provocar serias heridas o averías en el producto.
26. NOTA PARA LA PERSONA QUE INSTALE EL SISTEMA CATV
Se ha incluido este recordatorio para llamar la atención de quien instale el sistema
CATV, con respecto al Artículo 820-40 de la NEC, que entrega directivas de guía para realizar una conexión adecuada a tierra y, en particular, especifica que el cable de puesta a tierra debe ser conectado al sistema de conexión a tierra del edificio, lo más cerca del punto de entrada del cable como sea posible.
CONDENSACION
Se condensará humedad en la sección de funcionamiento del DVD/VCR si se lo trae de un lugar fresco a una habitación caliente o si la temperatura en la habitación sube repentinamente. En este caso, se verán afectadas las prestaciones del DVD/VCR. Para evitarlo, deje el DVD/VCR a la nueva temperatura durante aproximadamente una hora antes de conectarlo, o haga que la temperatura en la habitación suba gradualmente.
También puede condensarse humedad durante el verano si el DVD/VCR está expuesta a una corriente de aire del acondicionador de aire. En estos casos, cambie el lugar donde está instalado el DVD/VCR.
2C53607A (SP) Q Sheet 2 11/3/04, 6:31
Conexión a un televisor
Flujo de la señal A ENTRADA DE ANTANA
Antennas separadas
VHF y UHF
A SALIDA DE ANTANA
(amarilla) (roja) (blanca) a un tomacorriente de la red
(120 V CA, 60 Hz)
A SALIDA DE
VIDEO
Cordón AUDIO/
VIDEO (incluido)
Ajuste del canal de video
1 Mantenga presionado 3 o 4 durante 3 segundos en el mode desconectado para seleccionar CH 3 o 4.
3 4
El número del canal seleccionado parpadeará en la pantalla durante 3 segundos.
2 Presione POWER para encender el DVD/VCR.
3 Presione VCR DVD para seleccionar el modo VCR.
VCR
DVD
El indicador VCR del panel frontal se iluminará.
4 Encienda el televisor y ajústelo al canal 3 o 4, en correspondencia con el canal seleccionado en el paso 1 .
5 Presione TV/VCR para seleccionar la posición VCR.
TV/VCR
El indicador VCR se iluminará.
6 Presione el botón selector de canal en + o – (CH + / –) para recibir una estación de TV de su área. El número de canal aparecerá en la pantalla durante unos 4 segundos.
AENTRADA DE AUDIO
(blanca)
A ENTRADA
DE ANTANA
(roja)
A ENTRADA DE VIDEO
(amarilla)
Televisor o monitor con entrada de audio/video
Seleccion de idioma en pantalla
1
2
Presione VCR MENU . Presione SET + o – para seleccionar la opción “SYSTEM SETUP”, luego presione ENTER .
VCR MENU
SETUP
Si utiliza la unidad por primera vez y presiona VCR MENU , es posible que aparezca la pantalla de menú SYSTEM
SETUP en lugar de la pantalla del menú principal.
Presione SET + o – para seleccionar el modo
LANGUAGE, luego presione ENTER .
SET +
CH – CH +
ENTER
SET –
3 Presione SET + o – para seleccionar el idioma deseada: inglés (ENGLISH), español (ESPAÑOL) o francés
(FRANCAIS), luego presione ENTER .
SET +
CH – CH +
ENTER
SET –
4 Presione VCR MENU para volver a la imagen normal de TV.
VCR MENU
SETUP
2C53607A (SP) Q Sheet 3 11/3/04, 6:31
Ajuste de reloj automatico
1 Connecte la antena o sistema de cable.
• Si utiliza una caja de cable, enciéndala.
2 Enchufe el cable eléctrico de CA a un tomacorriente CA.
3 Compruebe que el DVD/VCR está apagado.
• Si presiona POWER , el ajuste automático no se activará.
4 Espere por lo menos tres minutos y presione POWER .
5 Presione CALL para verificar el reloj en la pantalla.
CALL
DISPLAY
Seleccion de TV/CATV
1 Presione VCR MENU .
VCR MENU
SETUP
SET +
CH –
ENTER
SET –
CH +
Presione SET + o – para seleccionar la opción “CH
SETUP”, luego presione
ENTER .
2 Presione SET + o – para seleccionar el modo “TV/CATV”.
SET +
CH – CH +
ENTER
SET –
3 Presione ENTER para seleccionar el modo TV o CATV.
La flecha indica el modo seleccionado.
SET +
CH –
ENTER
SET –
CH +
TV - Canales de VHF/UHF
CATV - Canales de TV CABLE
4 Presione VCR MENU para volver a la imagen normal de TV.
VCR MENU
SETUP
6 Si el reloj no ha quedado ajustado, verifique el estado de la antena. El reloj automático no funciona en el estado de recepción.
Ajuste de reroj manual
1 Presione VCR MENU .
VCR MENU
SETUP
2 Presione SET + o – para seleccionar la optión
“SYSTEM SETUP”, luego presione ENTER .
SET +
CH – CH +
ENTER
SET –
3 Presione SET + o – para seleccionar la opción
“CLOCK SET”, luego presione ENTER .
SET +
CH – CH +
ENTER
SET –
4 Presione el botón SET + o – para establecer el mes, y a continuación presione el botón ENTER .
SET +
CH – CH +
ENTER
SET –
5 Ajuste el día, año y hora de acuerdo con el procedimiento del paso 4 .
6 Una vez ajustado el reloj, la fecha y la hora empiezan a funcionar automáticamente.
Ajuste automático de los canales
1 Repita el paso 1 descrito arriba y presione SET + o – para seleccionar la opción “AUTO CH MEMORY”.
SET +
CH – CH +
ENTER
SET –
2 Luego presione ENTER .
SET +
CH – CH +
ENTER
SET –
Empieza la sintonización automática. La indicación de canal irá subiendo y cuando termina, la pantalla vuelve a su estado normal.
Borrado de un canal de la memoria
1 Repita el paso 1 descrito arriba y presione SET + o – para seleccionar la opción “ADD/DELETE”, luego presione ENTER .
SET +
CH – CH +
ENTER
SET –
1
4
7
CH –
2 Para añadir o borrar los canales deseados
1 Presione los botones de número o SET + o – para seleccionar un número de canal que desee añadir o borrar.
2
2
5
8
SET +
ENTER
SET –
3
6
9
CH +
0
Para añadir canales
Presione ENTER hasta que aparezca “ADD” en la pantalla para añadir el canal sin memorizar.
Para borrar canales
Presione ENTER hasta que aparezca “DELETE” en la pantalla para borrar el canal de la memoria.
El número del canal parpadeará.
1 2 3
2C53607A (SP) Q Sheet 4 11/3/04, 6:31
Reproducción
1 Coloque una cinta pregrabada. (Cuando se carga una cinta de cassette sin la lengüeta de prevención de borrado, la reproducción comenzará automáticamente.)
2 PARA INICIAR LA REPRODUCCION
PLAY
Presione PLAY . La reproducción comenzará. “ ” aparecerá en pantalla durante 4 segundos aproximadamente.
PARA INTERRUMPIR REPRODUCCION
Presione STOP (PARADA) una vez. La cinta parará, pero permanecerá cargada y lista para reproducir. “ ” aparecerá en pantalla durante 4 segundos aproximadamente.
Rebobinado o avance rápido de la cinta
Detenga la reproducción o la grabación mediante STOP .
Para rebobinar la cinta:
Presione REW .
REW
Para avanzar la cinta:
Presione FWD .
FWD
Para detener el bobinado de la cinta, presione STOP . Para pasar directamente a reproducción (sin presionar STOP ), presione
PLAY .
Modo de búsqueda de imagen hacia delante/atrás
Mientras se bobina la cinta, puede pasar al modo de búsqueda de imagen. Para ello, presione REW o FWD y manténgalo presionado. La unidad volverá a bobinar la cinta en cuanto se suelte el botón.
Búsqueda de imagen
Función de búsqueda de imagen hacia atrás
Presione REW una o dos veces durante la reproducción.
REW
Función de búsqueda de imagen hacia delante
Presione FWD una o dos veces durante la reproducción.
Para volver a la reproducción: Presione PLAY .
FWD
Imagen fija
Presione PAUSE/STILL durante la reproducción. Para continuar la reproducción normal: Presione PLAY o PAUSE/
STILL .
Camara lenta
Durante la reproducción presione SLOW .
Para volver a la reproducción: Presione PLAY o SLOW .
SLOW
Avance cuadro a cuadro
Presione PAUSE/STILL durante la reproducción.
Presione SLOW repetidamente: La imagen avanza cuadro a cuadro.
Para volver a la reproducción: Presione PLAY o PAUSE/STILL .
SLOW
Grabacion de un programa de TV
1 Coloque un cassette en el cual la lengüeta de protección contra borrados accidentales esté intacta.
El DVD/VCR se encenderá automáticamente.
2 Presione SP/SLP para seleccionar la velocidad de cinta deseada SP o SLP.
SP/SLP
PLAY MODE
El contador y “SP” o “SLP” se aparecerá en la pantalla durante 4 segundos aproximadamente.
3 Ajuste la opción TV/CATV en la posición apropiada.
TV - Canales de VHF/UHF
CATV - Canales de TV CABLE
4 Presione los botones de selección directa de canal para seleccionar el canal o CH + / – a grabar:
1
4
7
CH –
2
5
8
SET +
ENTER
SET –
3
6
9
CH +
0
Selección directa de canal en modo de TV:
Todos los canales podrán ser seleccionados en forma instantánea usando sólo dos botones.
(Por ejemplo, para seleccionar el canal 2, presione “0” y “2”. Si usted sólo presiona “2”, la selección del canal se retardará dos segundos.)
Para los canales de 10 en adelante, presione los dos digitos en orden.
Selección directa de canal en modo de CATV:
1-9 Presione 0 dos veces y luego 1 al 9 como se requiera. Ej.:para seleccionar 2, presione “ 002 ”.
10-12 Presione primero el 0 y luego los 2 dígitos restantes en el orden de izquierda a derecha. Ej.: presione
012 para “12”.
13-99 Presione 2 dígitos en orden.
Ej.: presione 22 para “22”.
100-125 Presione 3 dígitos en orden.
Ej.: Presione 110 para “110”.
5 Presione el botón REC .
REC/OTR
“ ” aparecerá en la pantalla durante 4 segundos aproximadamente. El indicador
“ REC ” aparecerá en pantalla.
6 Presione el botón de parada STOP para detener la grabacion.
“ ” aparecerá en pantalla durante 4 segundos aproximadamente.
2C53607A (SP) Q Sheet 5 11/3/04, 6:31
Grabacion por temporizador
1 Presione VCR MENU .
Seleccione la opción TIMER REC SET y presione ENTER .
VCR MENU
SETUP
SET +
CH – CH +
ENTER
SET –
2 Presione SET + o – para seleccionar el N° de programa, luego presione ENTER .
SET +
CH – CH +
ENTER
SET –
3 Presione SET + o – para seleccionar la fecha deseada, luego presione ENTER .
SET +
CH – CH +
ENTER
SET –
4 Ajuste el tiempo de partida, tiempo de término, canal y velocidad de cinta como en paso 3 .
5 Para fijar otros programas, repita los pasos 2 al 4 para fija el otro programas.
VCR MENU
SETUP
• Para volver a la pantalla normal, presione dos veces VCR MENU .
6 Presione TIMER REC . El símbolo de reloj ( ) aparecerá en el visualizador y el VCR quedará en modo de espera para grabación.
TIMER REC
Al mismo tiempo, el modo VCR cambiará automáticamente a modo DVD. Es posible utilizar el DVD incluso cuando el VCR está en modo de grabación por temporizador. Si no utiliza el DVD, apáguelo.
Grebacion por temporizador de un solo toque (OTR)
1 Coloque un cassette con la lengüeta de protección contra borrados accidentales esté intacta.
El DVD/VCR se encenderá automáticamente.
2 Presione SP/SLP para seleccionar la velocidad de la cinta deseada SP o SLP.
SP/SLP
PLAY MODE
El contador y “SP” o “SLP” aparecerán en pantalla durante 4 segundos aproximadamente.
3 Ajuste la opción TV/CATV en la posición apropiada.
TV - Canales de VHF/UHF
CATV - Canales de TV CABLE
4 Presione el botones de selección de canales directos o botón CH + / – para seleccionar el canal a ser grabado.
1 2 3
SET +
CH – CH +
4 5 6
ENTER
SET –
7 8 9 0
5 Presione OTR para comenzar la grabación. Presione el botón nuevamente para detener la grabación después de 30 minutos. Cada presión de OTR aumentará el tiempo de grabación hasta un máximo de 6 horas. OTR y el tiempo de grabación aparecerá en pantalla durante
4 segundos. Y “ ” aparecerá en el visualizador.
REC/OTR
Presione
Una vez
2 veces
3 veces
4 veces
5 veces
Tiempo de Grabac.
GRABAC. NORMAL
0:30
1:00
1:30
2:00
Presione
6 veces
7 veces
8 veces
9 veces
Tiempo de Grabac.
3:00
4:00
5:00
6:00
10 veces GRABAC. NORMAL
Para cancelar OTR
Presione STOP (PARADA) para apagar la energía.
“ ” aparecerá en pantalla durante 4 segundos aproximadamente.
Si desea ver la reproducción del DVD durante el OTR o grabación estándar, presione VCR DVD para cambiar al modo DVD y reproducir el DVD.
2C53607A (SP) Q Sheet 6 11/3/04, 6:31
Reproducción básica (DVD)
•
•
Preparación:
ENCIENDA el TV y ajústelo en el modo de entrada de video.
Presione VCR DVD para seleccionar el modo DVD. (El indicador DVD se iluminará.)
1 Presione OPEN/CLOSE en el aparato.
Se abrirá la bandeja del disco.
Reproducción con avance rápido
Presione FWD durante la reproducción normal.
Cada vez que presione el botón de FWD , aumentará la velocidad de la búsqueda.
• Para seguir con la reproducción normal, presione PLAY .
PLAY
FWD
2 Coloque un disco en la bandeja. Sujete el disco, colóquelo con el lado de etiqueta impresa hacia arriba, alinee en las guía y coloque el disco en su posición correcta.
3 Presione PLAY o OPEN/CLOSE en el aparato.
La bandeja del disco se cierra automáticamente.
En la pantalla del TV la indicación “ ” cambia a “Reading” y empieza la reproducción.
• Aparece la pantalla del menú en la pantalla de TV, si el disco tiene una función de menú.
En este caso, presione , , , ó ENTER para activar una función de menú.
PLAY
SET +
CH –
ENTER
SET –
CH +
4 Presione STOP para terminar la reproducción.
• El aparato graba el punto de parada, según el disco.
Aparece “ ” en la pantalla. Presione PLAY para continuar reproduciendo (desde el mismo punto).
• Si presiona nuevamente STOP o se retira el disco
(Aparece “ ” en la pantalla), el aparato borrará el punto de parada.
PLAY
Reproducción con retroceso rápido
Presione REW durante la reproducción normal.
Cada vez que presione el botón de REW , aumentará la velocidad de la búsqueda.
• Para seguir con la reproducción normal, presione PLAY .
REW
PLAY
Reproducción Fija
Presione PAUSE/STILL durante la reproducción normal para hacer una pausa en la reproducción.
• Para seguir con la reproducción normal, presione PLAY .
PLAY
5 Para la reproducción, presione STOP .
A continuación presione OPEN/CLOSE en el aparato.
Se abre la bandeja del disco.
Saque el disco y presione OPEN/CLOSE en el aparato y presione POWER ( ) . La bandeja del disco se cierra automáticamente y se desconecta el aparato.
Avance cuadro por cuadro
Presione PAUSE/STILL durante la imagen fija.
Avanza un cuadro cuando presione PAUSE/STILL una vez.
• Para seguir con la reproducción normal, presione PLAY .
PLAY
Reproducción de cámara lenta
Presione SLOW( ) durante la reproducción normal o cuadro a cuadro.
Cada vez que presione el botón de SLOW , cambiará la velocidad del slow.
• Para seguir con la reproducción normal, presione PLAY .
• Para volver a la imagen fija, presione PAUSE/STILL .
SLOW
PLAY
11/3/04, 6:31 2C53607A (SP) Q Sheet 7
Búsqueda de un capítulo o canción
Pulse SKIP o varias veces para visualizar el capítulo o la pista que desee.
La reproducción se inicia desde el capítulo o la pista que haya seleccionado.
INDEX
SKIP
+
Para localizar capítulos o pistas subsiguientes.
–
INDEX
SKIP
La reproducción se inicia desde el principio del capítulo o pista actual.
Si se pulsa dos veces, la reproducción se inicia desde el principio del capítulo o pista anterior.
Funciones básicas del control remoto
• Presione POWER (
VCR.
) para encender o apagar el DVD/
• Seleccione su modo operativo deseado (DVD o VCR) utilizando VCR DVD .
El indicador DVD o VCR del panel frontal le mostrará qué modo está seleccionado.
• Presione CH + o CH – para desplazarse por los canales uno a la vez.
• CH +/– ( / ) y SET +/– ( / ) se utilizan también para navegar por el sistema de menús en pantalla.
• Los botones de número permiten acceder directamente a canales concretos.
• Cada vez que se presiona VCR DVD en el control remoto, la pantalla alterna entre la pantalla VCR (modo
VCR) y la pantalla DVD (modo DVD).
Funcionamiento
• Apunte el mando a distancia al sensor remoto y presione los botones de control para hacer funcionar.
• Utilice el control remoto dentro de un ángulo de 30˚ hacia ambos lados del sensor remoto, hasta una distancia de unos 7 metros.
Coloque las pilas
1
Deslice la tapa del compartimento de las pilas siguiendo la dirección de la flecha.
2
Coloque dos pilas “AAA”, (suministradas) prestando atención a las marcas de polaridad en el compartimiento de las pilas.
3
Recoloque la tapa del compartimiento.
Notas sobre los derechos de autor
La ley prohibe copiar, difundir, mostrar, emitir por cable, reproducir en público, y alquilar sin permiso material con derechos de autor reservados (copyright).
Este dispositivo no graba en cinta DVDs protegidos contra copias.
El dispositivo no ha de utilizarse para copiar contenidos bajo
Copyright sin el permiso expreso por escrito del propietario de los derechos de autor.
La obtención de tal permiso es responsabilidad exclusiva del usuario.
Este producto incorpora la tecnología de protección de derechos de autor (Copyright) mediante un método que protege ciertas patentes de EE.UU. y otros derechos de propiedad intelectual pertenecientes a Macrovision Corporation y otros propietarios de derechos. La utilización de esta tecnología de protección deberá ser autorizada por Macrovision Corporation, y tiene como fin la utilización en el hogar y otros usos de contemplación limitados a menos que
Macrovision Corporation autorice otra cosa. Está prohibido modificar esta ingeniería y desmontar la unidad.
Fabricado bajo licencia de Dolby Laboratories.
“Dolby”, “Pro Logic” y el símbolo de la doble D son marcas comerciales de
Dolby Laboratories.
J2C53607A U
2C53607A (SP) Q Sheet 8 11/3/04, 6:31
Advertisement
