Panasonic SV-3800 Operating Instructions Manual

 Panasonic
Professional Digital Audio Tape Recorder
SV-3800
Operating Instructions
Aire CA a Ca reel of der IA
ET
Before connecting, operating or adjusting this product, please
read these instructions completely.
P RQT3200-1P
Dear customer
Thank you for purchasing this product.
For optimum performance and safety, please read these operating instructions carefully.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE SCREWS.
The model number and serial number of this
product can be found on either the back or the
bottom of the unit.
Please note them in the space provided below
and keep for future reference.
MODEL NUMBER _ SV-3800 __ NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED |
SERIAL NUMBER 3 SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the
user to the presence of uninsulated "dangerous
voltage” within the product's enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
THE FOLLOWING PHRASES ARE APPLIED ONLY FOR
U.S.A:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful |
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
The exclamation point within an equilateral
triangle is intended to alert the user to the pres-
ence of important operating and maintenance
(servicing) instructions in the literature accom-
panying the appliance.
CAUTION:
This equipment has been tested and found to
comply with the limits for a Class A digital device, WARNING:
pursuant to Part 15 of the FCC Rules. | TO REDUCE THE RISK OF FIRE OR
These limits are designed to provide reasonable
protection against harmful interference when the ELECTRIC SHOCK, DO NOT EXPOSE
equipment is operated in a commercial environ- THIS APPLIANCE TO RAIN OR MOIS-
ment. This equipment generates, uses, and can TURE.
radiate radio frequency energy and, if not installed 5
and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful inter-
ference in which case the user will be required to
correct the interference at his own expense.
Any unauthorized changes or modifications to this
equipment would void the users authority to
operate this device.
Listening caution
Selecting fine audio equipment such as the unit you've just purchased is only the start of your musical
enjoyment. Now it’s time to consider how you can maximize the fun and excitement your equipment offers. This
manufacturer and the Electronic Industries Association's Consumer Electronics Group want you to get the most
out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without
annoying blaring or distortion—and, most importantly, without affecting your sensitive hearing.
We recommend you to avoid prolonged exposure to excessive noise.
Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes of sound. So what
sounds “normal” can actually be loud and harmful to your hearing.
Guard against this by setting your equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
* Start your volume control at a low setting.
* Slowly increase the sound until you can hear it comfortably and clearly, and without distortion.
Once you have established a comfortable sound level:
* Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future. After all, we want you
listening for a lifetime.
10.
11.
12.
13.
Suggestions for Safety
Before using this unit, be sure to carefully read the applicable items of these operating instructions and the
safety suggestions. Afterwards keep them handy for future reference. Take special care to follow the warnings
indicated on the unit itself, as well as in the operating instructions.
Water and Moisture-Do not use the unit near any source of water or in excessively moist environments.
Object and Liquid Entry-Care should be taken so that objects do not fall, and liquids are not spilled, into the
enclosure through openings.
Ventilation-When installing the unit in a rack or any other location, be sure there is adequate ventilation.
Improper ventilation will cause overheating, and can damage the unit.
Heat-The unit should be situated away from heat sources such as radiators, heat registers, stoves, or other
equipment that produce heat.
Power Sources—The unit should be connected to a power supply only of the type described in the operating
instructions, or as marked on the unit.
Power Cord Protection-AC power supply cords should be routed so that they are not likely to be walked on or
pinched by items placed upon or against them. Pay particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
Never take hold of the plug or cord if your hand is wet. Always grasp the plug body when connecting or
disconnecting it.
Grounding of the plug-This unit is equipped with a 3-wire grounding-type plug, a plug having a third
(grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not
defeat the purpose of the grounding-type plug.
Carts and Stands—The unit should be used only with a cart or stand that is recommended by the
manufacturer. The unit and cart combination should be moved with care. Quick stops, excessive
force, and uneven surfaces may cause the unit and cart combination to overturn.
Wall or Ceiling Mounting-The unit should be mounted to a wall or ceiling only as recommended by the
manufacturer.
Cleaning—The unit should be cleaned only as recommended by the manufacturer.
Nonuse Periods-The AC power supply cord of the unit should be unplugged from the AC outlet when left
unused for a long period of time.
Damage Requiring Service-The unit should be serviced by qualified service personnel when:
(a) The AC power supply cord or the plug has been damaged; or
(b)Objects have fallen or liquid has been spilled into the unit; or
(c) The unit has been exposed to rain; or
(d)The unit does not operate normally or exhibits a marked change in performance; or
(e) The unit has been dropped, or the enclosure damaged.
Servicing—The user should not attempt to service the unit beyond that described in the operating instructions.
All other servicing should be referred to qualified service personnel.
Features
Enhanced Sound Quality
* Same Type Sigma-Delta 1-bit A/D Converter as in the highly acclaimed 5V-3700
e High-Resolution, Low-Distortion D/A Converter
Multiple Digital Interfaces
e AES/EBU
* TEC958 for Consumer Use (Coaxial and Optical)
* Front Panel Section of All 1/0 Formats
* Single Program Play
Contents
PREPARATIONS
Suppliód Accessories... . non ue ao
Installation... ;
опис ина. ние:
Concerning the Remote Control
Location of Controls ..
‘о anu
REGULAR OPERATIONS
Basic Operations for Recording and Playback.................s=ssessesescecomei A e có 2]
Playback Functions provided by the Recorder ... de
Playback Functions ls by the Remote Control Transmitter …….……..….mreenenneeneen 15
Before Recording ki EB en fer never hf
Кесот@ NE DE В
à 04 ES TR ESS E ooo oo док
SYSTEM DISPLAY MODE OPERATIONS
System Display Mole Selectión :...-... mn És A
REFERENCES
Operation Notes .. sn RUEDO IN UNO A CAS BBR à À
Quick Reference for System Display Mode Selection... sles rns o
Maintenance .............. a AS:
Concerning DAT Cassette Tape... lua a mm DS
ea pda a aa 0"
Specifications ... ee ee me A ee ae вона аооноиоадай но ойоонноеаоноосоно ооо нежосиаооссоо О
Ae
Supplied Accessories
Please check and identify the supplied accessories.
[1 AC power supply cord (RJA0017-K) .. sie asa]
|] Remote control transmitter (RAK-SV012WH) .. tesa all]
[] Batteries (AAA, IEC RO3, UM-4) …..….ccrrsssecerssserrsasercenssneceanens D
[1] Rack mount kit .. vee 1
(The rack ears: RYQ0059)
(The rack panels: RYQ0060)
E] Serews OCTNAS+FIOERZ) mama сан ий она нелвиноваение@
Installation
Installation of rack mount kit
1 Assemble the rack ears and panels, and tighten 2 Remove the4screwsonside enclosure, and attach
with included screws. the unit to the rack mount.
Notes on placement
Screws (4)
Included
screws (8)
EH Place on a flat, level surface so that the front-rear inclination does not exceed 15°.
B Avoid places such as the following:
Near any equipment or device that generates strong magnetism.
On any heat-generating equipment or device, or in any place where the temperature is high (40°C or
higher).
Extremely cold places (5°C or below).
Near an AM/FM tuner or TV.
(It may produce noise in the broadcast, or disturb the TV picture.)
For long periods of time in direct sunlight.
In dusty or smoky locations.
In locations prone to vibrations.
In locations where the rear panel is less than 10 cm (about 4”) away from the wall or back of an audio
rack.
Within reach of children.
№ Do not place heavy objects, other than system components, on top of the unit.
B When carrying or storing the unit, handle it with care so it is not subjected to any strong bumps.
E To avoid problems due to vibration.
Do not place a book or similar object under this unit.
Do not route the connection cables (of this or other units) across the operation panel, across the top, or
under the unit.
Connections
Rear Panel — ANALOG IN terminals
These are balanced analog audio XLR input connectors.
— ANALOG OUT terminals
These are balanced analog audio XLR output connectors.
— REMOTE CONTROL jack (PARALLEL)
| See page 7.
|
| |
— AES/EBU terminals (IN/OUT)
These terminals are for input or output
of signals for the professional digital interface.
Fs ® с Fr
Ta [ANALOG | à | EA A Ne
"8 5 NL = (ест) ПБ) ME TE is i BLAYIOUT)
be ® ¢ = Ni = econ vor > 2 «ть
©
| SS 5 © y E ® ;
| = E.
- =
AC IN jack
Connect to the grounded AC outlet
| with the included AC power supply cord.
| — IEC (IEC 958 for consumer use) coaxial jacks (IN/OUT)
| These terminals are for input or output of digital signals
from/to a consumer unit by using the coaxial cable.
— IEC (IEC 958 for consumer use) optical terminals (IN/OUT)
These terminals are for input or output of digital signals
from/to a consumer unit by using the optical cable.
Input connector Output connector
GND
+ (Hot) + (Hot)
— (Cold)
When making digital IN/OUT connections
If the connections to studio equipment are set incorrectly, a loop may be set up where the output of the unit is
connected to its recording input. This will not only set up an oscillation but may also damage the monitor
speakers. Attention should therefore be paid to the following points:
1) When recording or playing back through the unit's DIGITAL IN/OUT terminals, be sure to connect these
terminals to the DIGITAL PLAYBACK (IN)/DIGITAL REC OUT (OUT) terminals of other equipment.
2) If the monitor amplifier has no DIGITAL PLAYBACK or DIGITAL REC OUT terminals, this unit (DAT) can be
used only for playback through the ordinary DIGITAL INPUT terminals on the amplifier.
3) If connections are made as in 2) and it is desired to record, do not on any account set the INPUT SELECTOR of
the amplifier to “DIGITAL”.
Concerning the Remote Control
This unit has two systems for remote control operation, using the infra-red remote sensor or the 8-pin parallel
input terminals.
Remote Control Transmitter
Battery installation
Insert the batteries with using two AAA, IEC R03, UM-4 (1.5 V) or equivalent batteries in the correct polarities
(+, =).
To remove the batteries, push down the (-) side.
Notes: * Do not mix old and new batteries, or batteries of different types (manganese and alkaline, etc.).
* Never subject batteries to excessive heat or flame; do not attempt to disassemble them; and be sure they
are not short-circuited.
* If the remote control is not to be used for a long period of time, remove the batteries and store them in a
cool, dark place.
* Do not attempt to recharge alkaline or manganese batteries.
Battery life:
The battery life is about one year. The batteries should be replaced if commands from the remote control
transmitter do not operate the unit even when the transmitter is held close to the front panel.
Correct method of use
1 Aim the remote control's transmission window toward the unit's sensor. Avoid any obstacles.
2 Use the remote control within a 60-degree angle of the unit.
The maximum distance is within 7 meters (23 feet) directly facing toward the unit.
Notes: * Be sure the transmission window and the unit's sensor are free from dust. Excessive dust might affect its
performance.
* The operation may not be correct if direct sunlight or other strong light source strikes the receiving sensor
of this unit. If there is a problem, place the unit away from the light source.
* If this unit is installed in a rack with glass doors, the glass doors’ thickness or color might make it neces-
sary to use the remote control a shorter distance from the unit.
8-Pin Parallel Input Terminals
By connecting the following circuits, the SV-3800 can be operated by remote control using normal switches.
E
PLAY |
|
©
—— FF/CUE | 1 SKIP DD
с) ©) |
GND
STOP
O O |
REC
O O— |
Concerning the Remote Control
8-Pin Remote Specifications
8-pin remote key code:
Note: The time taken until the key code for operating multiple commands must be less than 1 ms, and each code
input must be more than 60 ms.
Function 8-pin DIN jack key | Function 8-pin DIN jack key
Code No. 87654321 Code No. 87654321
open 00000001 memory 01000000
music scan 00011000 recall 01000001
skip cancel 00110000 repeat 01100001
stop 01111111
| play 11111011 write_start-ID 01010000
write 01101001 write_skip—ID 01010001
erase_start-ID 01110000
auto rec mute 00100000 erase_skip—ID 01110001
rec 11011111
pause 11111110 | | rec+play 11011011
forward skip 10111111 | direct rec_pause 00011001
reverse skip 11111101 direct rec_play 00111000
unload 00111001
counter mode 00101000 mode+reset+pause 10110000
auto PNO 00110001
| fade in 00100001 skip cancel on 00000010
fade out 00001000 skip cancel off 00000011
ff 11101111 auto PNO on 00100010
rew 11110111 | auto PNO off 00100011
| renumber 00010001
counter reset 00001001
end-ID 01101000
skip—ID 01001001
start-ID 01001000
end search 01100000
erase 00010000
0 (key pad) 11000001
1 (key pad) 10000000
2 (key pad) 10000001
3 (key pad) 10100000
4 (key pad) 10100001
5 (key pad) 10001000
6 (key pad) 10001001
7 (key pad) 10101000
8 (key pad) 10101001
9 (key pad) 11000000
0: The connection is shorted.
1: The connection is open.
Location of Controls
[t's a good idea to keep these Operating Instructions open at this page when
using the unit.
Front Panel
SHUTTLE SEARCH dial
COUNTER MODE/RESET buttons © Indexing buttons
OPEN/CLOSE button
SiN la: Cannetño Lidl \ \ Basic operation buttons
| \ | \ qu /
: fm | ===
SANS СОС
—] Чл PAUSE
zz ДЕН EC 2d
Ji 5 ESE
"TD ar —
LJ T | — = =
SEALE TINTS | \ REC LEVEL controls
LEVEL control Remote control signal sensor
- INPUT selector
SAMPLING FREQUENCY selector ue
HEADPHONES FADE IN/OUT buttons
jack PNO/START ID AUTO button/indicator MUSIC SCAN button
DISPLAY FUNCTION selectors (Using with the PAUSE button) SKIP PLAY CANCEL button/indicator
Location of Controls
Display Panel
End indicator Erase indicator
Skip ID indicator Cleaning indicator
Start ID indicator Dew indicator
Repeat indicator PNO (program number) indicator
Sampling frequency Program number display
indicators
|" 48kHz 44.1kHz|| 32kHz | > | |start1D|| skip ID | end || erase / / \
cleaning | РМО + LT [|
CCE EER ERE RR EEE RRR) [over] | dew LILI
-60 -50 40 BO + 24 #18 12 8 061. 440080 gin 7
sim HHH HE
R Hart over | | P-time / |
Peak level meter Over indicator Counter display
Remote Control Transmitter
REPEAT button
RECALL button =
Program number
buttons
[3 =
MEMORY button” NI 5/5
DIO
— SETENTA IAF
DAT DECK lied
Panasonic
Unexplained buttons on the remote control transmitter function identically to their corresponding parts on the
SV-3800.
10
Basic Operations for Recording and Playback
Inserting and removing cassette tapes
1 Press the POWER switch to switch on power.
2 Press the OPEN/CLOSE button.
The cassette holder will open.
3 Insert a cassette tape.
Insert a cassette correctly so that the tape reels are visible.
4 Press the OPEN/CLOSE button.
The cassette tape will be loaded automatically into the transport mechanism.
Note: During recording, the OPEN/CLOSE button does not operate. When removing tape, first press STOP’ button
and then press this button.
While the cassette holder is being opened or closed, the counter display will flash. When the display is
flashing, the control buttons will not operate.
When the power is switched on with a cassette tape in the unit, counter display shows:
When the cassette tape has not been inserted, no display will be shown.
Basic operations
Object to operate Button to press Indicator
To begin playback Press the PLAY button. The play indicator illuminates.
To begin recording Press the REC button and then press The rec and play indicators illuminate.
the PLAY button.
Tointerrupt recording or Press the PAUSE button. The pause indicator illuminates.
playback temporarily (Press the PLAY button to resume
recording or playback.)
To stop recording or Press the STOP button.
playback
Unloading function
After 12 hours of the unit in stop, pause or record standby modes, the cassette tape will be released automatically
from the head drum.
CAUTION! If the unit is not going to be used for extended periods, rewind the cassette tape back to the beginning,
remove it and turn otf the power.
Search Functions
Fast-forward play, rewind play (During playback)
When the FF/CUE button or REW/REV button is kept depressed: Advances or reverses the tape during
playback at about 3 times normal speed, with reduced level audio output (does not operate during recording).
11
12
Basic Operations for Recording and Playback
Note: When operating the “Cue” or “Review”, the playback will contain some chatter noise causing by the head
crossing over the recorded track on the helical slant. This is not a malfunction. Reduce the volume of the
monitor amplifier to optimum level. (Take special care during playback with digital output signals.)
Fast-forward, rewind (During stop mode)
When the FF/CUE button or REW /REV button is pressed , advances /reverses tape at about 250 times normal
speed.
Shuttle search
This function allows you to search rapidly forward or backward on the tape for specific sections with a high
degree of accuracy, while listening to the material recorded on the tape.
Search play speed (four steps)
Operation mode
Scale Play Pause
1 x 3 x /
2 х5 x 1
3 x 9 x 2
- | x 15 | “e
Basic Operations for Recording and Playback
Counter Display
Program time indicator
Counter display mode | Absolute time indicator
| me time indicator
| _
remain Y + OO
A-t —
Potime 1 + 1 1 «LI I
I
Hour Minute Second
Counter display mode changes in the order as shown below each time the COUNTER MODE button is pressed.
Counter mode Description
1 Absolute time (A-time) The time elapsed from the start of the tape until the current recording or
playback position on the tape is indicated in hours/minutes/seconds.
NE er During recording this time is automatically recorded to enable the tape
> a 27 E position to be checked or a particular position on the tape to be searched
accurately. The time is not displayed if it was not written during recording.
2 Program time (P-time) The amount of play time that has elapsed from the start of a program is
| indicated for each program. (The start of each program is designated by a
mec on | start ID or PNQ.) If the start of a program has been passed when a tape with
ima Ed AF the absolute time recorded on it is rewound, the remaining program time
(Remain Program Time) is indicated.
3 Remain time (remain) The remaining time on the tape is indicated in hours/ minutes. This makes
it possible to check how much time is left on the tape during tape editing
remain (TTC * operations. Use this display only as a general guideline since there may be
Joss a slight discrepancy from the actual amount of tape remaining.
4 Tape counter The count displayed corresponds to the rotational count
| of the tape reel. Select this position when the absolute time has
Г 5. - E not been written.
Use the COUNTER RESET button to reset the tape counter to “0000”.
5 Peak margin The peak level margin is indicated.
| “PEE-E” appears when the peak level is exceeded. “PP02-7" indicates that
| H # = ne 5 the margin is 2.7 dB, and the digit occupying the first decimal place is
| indicated only when the margin is less than 3 dB.
If the reset key is pressed in this display mode, the existing margin is
cleared.
When the sub codes are not recorded on the tape (when a brand-new tape is used)
The bar moves from left to right. (The bar moves from right to left during the review or rewind modes.)
bar
The bar also appears during the following cases:
* The program time is not identified.
* The remain time is being calculated.
When the tape comes to the end
“E” appears on the program number display.
>NO E|
13
Playback Functions provided by the Recorder
Skipping Programs (Skip Play)
Notes:
This function cues to the next tape position where a Start ID has been recorded.
* This function may not operate correctly in the case of very short audio segments (about 30 sec. or less).
* This function is different from Auto Skip Play Function in indexing. (Refer to pages 23 and 26.)
Skip forward or backward (Forward or Reverse Skip Play)
Note:
Note:
(1) Setting the skip number
In the playback, standby or stop mode, press the forward or reverse SKIP button.
When the button is pressed, the skip number is incremented or decremented by 1; whenitis kept depressed more
than 1 sec., the number is continuously incremented or decremented (up to +99).
Press the forward or reverse SKIP button so that the number of programs you want to skip are displayed in the
program number display panel. The number of times the button is pressed is indicated with a plus “+” ora minus
— sign.
During reverse skip, the segment now being played is counted as one skip.
(2) Starting skip search
Skip search is started after the skip number setting is entered.
Action taken Operation
1) Do not press the SKIP button within 2 seconds after Search is commenced automatically.
the skip number was set. (In the playback mode, playback is started after the
search, and in the other mode, the pause mode is
established after the search.)
2) Press the PLAY or PAUSE button within 2 seconds Playback search or pause search is commenced.
after the skip number was set.
The PLAY or PAUSE button may by be pressed even during search operation to select either mode upon
completion of the search.
During skip search, changing the skip number is not possible.
Skip during program play
Each time the SKIP button is pressed during program play, the program sequence changes and is displayed.
After the program sequence has been memorized and the forward SKIP button is pressed while a certain
selection is being played, the tape advances to the next selection.
After the program sequence has been memorized and the reverse SKIP’ button is pressed while a certain selection
is being played, the tape goes back to the beginning of the current selection. If the button is pressed again, the
tape goes back to the beginning of the previous selection.
Identifying the Contents of Each Program Recorded on the Tape (Music Scan Play)
Note:
14
Press MUSIC SCAN button.
The beginning of each audio segment from which MUSIC SCAN button is pressed will be played for approx.
15 sec., and the play indicator will flash.
It a desired audio segment is found during scanning, press the PLAY button to continue playback. When the unit
is changed to the playback mode, the play indicator will illuminate.
To interrupt the scan, press the STOP button.
Music scan does not function during program play.
Playback Functions provided by the Remote Control Transmitter
Playback of any Desired Segment (Access Play)
Notes:
Example:
By specifying a segment and pressing the PLAY button, playback will begin from that location.
* This operation cannot be performed with tapes which have no program numbers recorded on them.
* |t may not be possible to find short segments less than 1 minute long.
Select the desired program number with the program number button on the remote control transmitter. The
program number will appear on the program number display.
Press the PLAY button. While the program number is being searched, the play indicator will flash. After the
specified program number has searched, the play indicator illuminates and play begins.
To begin playback from 10th program
Press “17, “0”, and PLAY buttons in that order. The unit searches for the specified program, playback begins
and the program is displayed on the program number display.
To cue the machine to a desired segment:
If a desired audio segment is specified and the PAUSE button is pressed, the specified program number is
searched and the unit enters the pause mode. While the tape is searching for each segment, the pause indicator
will flash. To begin playback, press the PLAY button.
To change a specified program (Only effective in stop mode):
Press the “0” button twice, then press the correct button for the desired selection.
Playback of Segments in any Desired Order (Program Play)
Note:
Example:
This function cannot be used with tapes on which program numbers have not been recorded.
Select the desired segments with the program number buttons on the remote control transmitter in the stop
mode. The segment selected will appear in the program number display panel.
Press the MEMORY button on the remote control transmitter to memorize specified segment.
Repeat steps 1 and 2 to memorize segments in desired order.
Up to 32 steps can be memorized in this way.
Press the PLAY button. Playback begins from the first selection. While the tape is searching for the beginning
of selections, the play indicator flashes. After memorizing, if the PAUSE button is then pressed, the first selection
is searched and the unit enters the pause mode.
To play segments 3, 5 and 8 in that order
Press “3°, MEMORY "5, "MEMORY 87, MEMORY”, and PLA Y button.
When the last program has been played, the unit enters the stop mode.
To change program selections:
[fit is desired to change some selections and the MEMORY button has not yet been pressed, press the “0” button
twice to cancel the incorrect selections. Then enter the correct selections. When the MEMORY button has already
been pressed, pressing the STOP button cancels all selections and then enter the new selections again.
To confirm memorized program selections:
[f for example, segments 3, 5 and 8 have been memorized in that order, and the RECALL button is pressed while
segment 3 is playing, the display will show first memorized program and sequence (PNO 03, P-01), next
memorized program and sequence (PNO 05, P-02), and last memorized program and sequence (PNO 08, ’-03)
in that order.
After last memorized program is displayed, display returns to original display.
15
16
Playback Functions Provided by the Remote Control Transmitter
Reference:
To interrupt program play:
Press the STOP button.
To recall the programmed selections:
When the RECALL button is pressed once the STOP button has been pressed, the programming is restored.
After recalling the programmed selections by pressing the RECALL button, the additional programs can be
entered.
[f the program number button is pressed instead of the RECALL button once the STOP button has been pressed,
the input program is cleared and programming commences anew from program 1.
The program is considered to be at its end in the following circumstances:
* When the Start ID of the next program has been detected
* When the Skip ID has been detected while the auto skip play mode is on
* When a blank section (in which an audio level of less than selected detection level continues for more than
2 seconds) has been detected while the program playback blank skip mode is on
(Refer to the system display functions and Automatic recording of program numbers.)
* When the tape has reached its end
Playing Tape Repeatedly (Repeat Play)
This function will repeatedly play either an entire tape, or programmed selections up to a maximum of 16 times.
1 Press the REPEAT button on the remote control transmitter. The repeat indicator illuminates.
2 Press the PLAY button. The play indicator illuminates, and play begins.
If all the segments are to be played repeatedly and an End mark is detected, the tape will return to the beginning
and playback will begin again.
To cancel repeat play:
Press the REPEAT button. The repeat indicator turns off and the unit returns to the original playback mode.
[f the STOP button is pressed, repeat play is cancelled and the tape stops.
Before Recording
Recording Absolute Time
Be sure to observe the following precautions when recording onto a tape.
V Make sure the accidental erasure prevention tab on the DAT tape is set to the recording position so that
recording can be performed (see page 39).
V Insert the cassette tape after the power is switched on.
When the power is switched on with a cassette tape in the unit, absolute time is not displayed on the counter
display. To make sure that all recordings contain absolute time information, first operate the PLAY button,
perform an end search (see page 21), or rewind tape to the beginning. Then, carry out normal recording
operations.
V Even with new blank tapes, the tape may need to be rewound or End Search Performed. The Absolute Time
display must show “0:00:00”, which indicates that the machine recognizes the beginning of a tape. Absolute
time will not be recorded if this display is not present.
V To advance the tape during recording, use the AUTO REC MUTE button without using the PLAY button or
the FF / CUE button.
V When recording from a point mid-way along the tape, use the end search function to search for the end of
IMPORTANT
NOTE:
the last recorded passage, and perform pick-up recording to ensure that there will no section without
absolute time informations (see page 21).
An absolute Time indication must be present on the display in order for the machine to record absolute time
from that point on. If the machine does not recognize its present position, whether it is “0:00:00” or any
other time, Absolute Time will not record. Audio recording, however, is unaffected.
Soundless recording and non-recording:
During soundless recording, the tape travels in a recording state and only the data necessary for recording digital
signals are recorded. In this state, no audio signals are recorded.
As opposed to this, during non-recording, the tape travels in a state other than the recording state, and neither
the audio signals nor the data necessary for recording are recorded.
(This is the same condition as that of a brand new tape.)
[f such a non-recorded section exists in the middle of a recorded tape, important information such as absolute
time will not be recorded.
Recording Program Numbers During Recording
1) Automatic
Note:
There are two ways of recording program numbers as follows:
recording of program numbers
1 Press the PNO/START ID AUTO button if the pno/start ID auto indicator is not illuminated. The pno/start ID
auto indicator illuminates.
The “auto” mode setting, whether ON or OFF, applying when the power was last turned off is retained
when the power is turned on.
2 Perform recording operation. When recording has started, program numbers are recorded automatically in
order (segment 01,02, 03...) as long as a program begins after there has been at least 2 seconds of no sound (below
selected detection level). Program numbers are indicated on the display once they are recorded.
Setting the PNO/START ID AUTO detection level
The level at which a program is to be judged to have no sound can be set to any level in 10 dB increments between
—20 dB and —60 dB.
When the PNO/START ID AUTO button is pressed with the “auto” mode ON, the mode will be turned off.
When the same button is pressed with the “auto” mode OFF, the selected detection level is indicated
momentarily (for approx. 1.2 sec.). If the button is pressed again while the detection level is indicated, the level
is changed by one setting (—40dB — -50dB — -60dB — -20dB — -30dB — —40dB, etc.).
17
18
Before Recording
IMPORTANT
NOTE:
As with absolute time, the machine must recognize the current program number (PNO) in order to record the
next sequential number. If there is no PNO showing on the display, then only Start ID's are recorded, without
PNO's. This can occur, for example, if the tape is inserted into the machine in the middle of a segment, because
Start ID's and PNO's are recorded only for the first 9 seconds of a program.
To set program numbers before recording:
In the recording standby mode, use the program number buttons on the remote control transmitter to input the
number of the program to be recorded next.
The program number input flashes on the program number display.
Press the PLAY or FADE IN button.
Recording commences, and when the next Start ID is recorded, the programs are recorded starting with the
program number which was set.
e If the audio level exceeds selected detection level after it has fallen below selected detection level for more
than two seconds, the Start ID is recorded automatically.
* When making a recording from another DAT using the IEC Digital Input, Start ID's may be transmitted as
well as the audio information. However, not all models transmit Start ID's. If in doubt, check with the
manufacturer. Start ID's are recognized by the IEC Digital I/O on Panasonic and Technics models SV-
DA10/3200/3700/3900/4100/3800. Additionally, the SV-4100/3800 AES/EBU ports transmit and receive
Start ID's.
* Tf the source tape has Start ID's which are less than 18 seconds apart, it will either not record onto the
copy, or may be offset a few seconds late.
* Some compact discs have a very short interval between tunes. Even in these cases, however, if your CD
player has an auto space function, the space between tunes can be extended automatically so that pro-
gram numbers are entered correctly during recording.
To cancel the automatic program numbering function:
Press the PNO/START ID AUTO button.
2) Manual recording of program numbers
Note:
1 Make sure the pno/start ID auto indicator goes out. Press the PNO/START ID AUTO button if the indicator is
illuminated.
Press the PLAY button where you want to record a program number during recording. Each time this operation
is performed, a program number (1, 2, 3 etc...) is recorded on the tape. These program numbers may be checked
on the program number display.
Make sure that the PNO display shows a program number. In this case, starting the tape from the record
standby mode will increment that number and record it. If no number is indicated, then only a start ID is
recorded without a program number (PNO).
* In automatic or manual recording of program numbers, a Start ID of 9 seconds duration is recorded each
time a program number is recorded.
* If the tape is stopped temporarily with the PAUSE button, AUTO REC MUTE button, or the fade out,
then recording is started again by pressing the PLAY button after the pno/start ID auto indicator has
gone out, a program number is recorded at that point.
Recording
Making Analog Recordings
Recording from the beginning of the tape
1 Set the INPUT selector to the ANALOG position and select the desired sampling frequency (44.1 kHz or 48 kHz).
2 Press the REW/REV button. Be sure to rewind the tape even if a brand-new tape is used.
This insures that the machine senses beginning of tape, and absolute time is initialized to “0:00:00”. Failure to
do this may result in absolute time and PNO's not to be recorded. (In the worst case, however, audio is recorded,
and absolute time and PNO's can be added later without disturbance to the recording = retime function on
page 26.)
3 Press the REC button. When a tape is used from its beginning, the rec and play indicators illuminate for approx.
4 seconds, and the pause indicator flashes. This is to erase any previous recording, and establish a leader which
is required by the system. When this process is complete, the rec and pause indicators illuminate, and the play
indicator goes out, indicating record standby mode. If the REC button is pressed when the tape is at a location
other than the beginning, the unitimmediately enters record standby mode, the tape stays at the present location
until the PLAY button is pressed.
4 Input the audio source that is to be recorded, and adjust the recording level with the REC LEVEL controls. (see
below.)
5 Press the PLAY button. The play indicator illuminates, and recording begins. The pause indicator goes out.
Adjusting the recording level
The -18 dB level on the meter corresponds to either +4 dB or —10 dB at the analog outputs, depending on the
setting of DISPLAY FUNCTION SELECTORS. This is compatible with most professional and semi-pro analog
equipment. However, in practical digital recording application, it is often desired to record at maximum level
(0 dB) for optimum resolution. In this case, the recording level must be adjusted for the highest possible level
where peak levels never trigger the “over” indicator.
Peak level meter Peak hold
1
CES EEE INT Lee
60-50 40 -30| +24 « -18 +-12 + 6 « -3 + 0 “8
a rina wm =
| Л
ill:
Бы
= = = = =
1 == | 8Р -
_184g Headroom pistortion
nominal level
Note: Since this unit uses digital-drive peak level meters, the recording signals will not be distorted provided that
the level has been adjusted so that the over indicator does not light.
How to Make Silent Spaces on Tape/How to Erase
Inserting a silent space on the tape (Auto Rec Mute Function)
1 By inserting a silent space, a new recording can be clearly distinguished from the previous one. Press the REC
button. After the unit enters the record standby mode, press the AUTO REC MUTE button. A silent space of
approx. 4 seconds will then be recorded on the tape. During these 4 seconds, the pause indicator will flash and
the play indicator will illuminate.
After a recording has finished, be sure to insert a silent space of 4 seconds before stopping or pausing the tape.
Consecutive recording and program play will then be performed more accurately.
2 To eliminate unwanted sections during a recording, press the AUTO REC MUTE button while the unit is in the
recording mode. A silent space of approx. 4 seconds will be automatically inserted on the tape, and
the unit will then enter the record standby mode. To begin recording again, press the PLAY button. 19
20
Recording
To make the silent space shorter or longer:
№ Making it shorter (less than 4 seconds)
Press the AUTO REC MUTE button, then press the PAUSE button or PLAY button within 4 seconds.
When the PAUSE button is pressed, the unit enters the pause mode; when the PLAY button is pressed, recording
begins.
H Making it longer (greater than 4 seconds)
Press and hold the AUTO REC MUTE button as long as necessary. When the button is released, the unit enters
the record standby mode. To resume recording, press the PLAY button.
Erasing a recorded tape
When a tape is recorded again, any previous recording is erased automatically. To erase only the recording
(without erasing absolute time), set the REC LEVEL controls to the minimum position, and record up to the end
of the tape (check the peak level meter does not move).
When end search is performed on a tape that has been erased up to the end by the above method, the unit runs
to the end of the tape. This is because end search looks for either blank, unused tape or an End mark. Although
the previous recording is erased, absolute time is not, and this is viewed as a silent recording by the end search
function.
Recording
Making Digital Recordings
Before making digital recordings, check the following settings:
type of digital audio interface (AES/EBU or IEC coaxial, optical)
value of ID6 SCMS status (only for AES/EBU 1/0 recordings)
Ze
For further details, see “System Display Mode Selection” on pages 28-31. After the required settings have been
made, follow the procedures described below.
1 Make sure the INPUT selector is set to the DIGITAL position.
2 Press the REC button. The unit enters the record standby mode. The rec indicator and pause indicator
illuminates.
3 Press the PLAY button. The pause indicator goes out. The play indicator illuminates, and recording begins.
4 Play the digital source that is to be recorded. The digital input can be monitored through the analog output, or
via headphones.
Notes: * When making digital recordings, rec level adjustment cannot be made.
* When the INPUT indicator flashes, recording cannot be performed. In this case, the digital input
terminals may not be correctly connected, or input terminal selection is not set correctly. (Refer to pages 6
and 28.) Connections, signals and input terminal selection should therefore be re-checked.
Only when signals are recorded in the automatic program number recording mode and a DAT recorder is used
as the recording source are the Start IDs and Skip IDs on the player's tape recorded straight onto the recorder's
tape. With any other source, the intervals between the programs are detected by the signal level for recording.
When recording is started with the program numbers displayed, it is possible to record these numbers as well.
If the program numbers are not displayed, only the Start IDs will be recorded. However, the program numbers
can be added later using the renumbering function. The desired program number can also be set by using the
program number buttons on the remote control transmitter.
The automatic program number recording mode is established when material from an old type of DAT is edited
with its digital signals.
Recording from the Middle of the Tape
1 Press the END SEARCH button.
The end of the last recording on the tape is searched at high speed, and the tape stops.
Unrecorded
«— portion —
ИИ,
End of recording 4
While the end search is being carried out “EE” flashes on the program number display.
2 Press the REC button. The rec and pause indicators illuminate, and absolute time will then be recorded once the
PLAY button is pressed.
Notes: * The end search function may not operate correctly for tapes that contain a recording lasting only for 1
minute or so.
* In the end search mode the tape may stop at a position very slightly before from the last recording
position.
21
22
Recording
Concerning end search
When using a tape that has been previously recorded on, it may be adviseable to record an End mark at the end
of the new recording. End Search will cue up to the End mark if it does not first encounter a blank, unused portion
of tape. If no End mark is present, then it searches for unused tape.
Note: А tape is recorded on even if there is no audio input. Anytime the unit is run in Recording mode, an “RF
Envelope” will be present on the tape. An End mark must be present in order for End Search to work on
tapes which have the RF Envelope recorded throughout.
Initial recording
A
|
Last recording position on new recording Unrecorded
(End mark should be recorded.) portion
Making Fade In/Fade Out Recordings
Fade in
This starts recording and gradually increases the level of the sound.
= | = =
Record Fade in Normal recording
standby (for approx.
mode 2'/ sec.)
1 Follow the procedures described in “Before Recording” and “Recording”, according to the source of the sound.
2 Press the REC button to enter the record standby mode.
3 Press the FADE IN button. Full-level recording begins after an approx. 2'/ seconds fade in period.
Fade out
This gradually reduces the level of the sound, and enters the pause mode.
spa — > i >
Normal recording Fade out Silent Record
(for approx. space standby
5 sec.) (4 sec.) mode
Press the FADE OUT button during recording.
After approx. 5 seconds of fade out, approx. 4 seconds silent spaceis recorded, and then the unit enters the record
standby mode.
Indexing
Description of Sub Codes
DAT recordings consist not only of audio information, but also sub code. The sub code portion of the recording
includes absolute time, PNO's, Start ID's, Skip 1D's, etc. These sub codes enable the beginning of a program to
be searched during playback or to edit a tape after it has been recorded.
Sub codes are used not only for automatically writing information during recording, but can also be changed
later without disturbing the audio.
Subcodes available with this unit
Note:
Concerning Indexing
Notes:
Type of sub code Main function Description
Start ID Indicating the beginning of the A Start ID can be recorded at the beginning of any audio
program. segment, or between segments as required. The Start ID
can be recorded in either manual or automatic mode.
Recorded Start ID's can be automatically re-assigned a
set of sequence numbers using the Renumber function.
Skip ID Causing the unitto gointofast- Skip ID's canbe recorded to provide automatically skip-
forward mode until the next over function, to jump parts of the tape you do not wish *
Start ID is reached, in order to to hear (Auto Skip Play Function).
skip unwanted material. Skip ID can be manually recorded or erased at the
required position.
End mark Indicating the end of the last End mark can be recorded or erased at the end of the
recording on the tape. recording, and searched by using end search function.
Program The number of the program Program numbers are recorded in sequential order.
number (PNO) recorded on tape. After erasing or re-recording Start ID's, program num-
bers can be rearranged in Start ID order.
Recording of a sub code other than an End mark will have no effect on the audio signals recorded on the
tape.
During recording, Start ID, program number, absolute time and program time can be recorded automatically
by setting the PNO/START ID AUTO button. Program numbers can be re-sequenced by indexing. To index the
tape in stop or pause mode, advance the tape to the desired position by means of the SHUTTLE SEARCH dial,
FF/CUE button or REW/REV button, and then stop it with the PAUSE or STOP button.
* Reset the accidental erasure prevention tabs, so that the tape can be recorded.
* [f the OPEN/CLOSE button is pressed and the cassette tape is removed during indexing, the index mode
will be cancelled.
* Start ID's may be written without PNO's, but a PNO cannot be written without a Start ID. If a Start ID
only is on the tape, it can be accessed with the Skip Forward and Skip Backward functions. Random
access by program number in this case is not possible.
23
Indexing
Start ID
Silent space Silent space Silent space
ow |=+— LA "
Music Music Music
(1st segment) (2nd segment) (3rd segment)
ИИА |
! Start ID (9 sec.) Start ID (9 sec.) Start ID (9 sec.) Unrecorded
Start of tape portion
Skip ID/End mark Unrecorded
portion
Music |
Music (2nd Music
(1st segment) segment) (3rd segment)
Skip ID (1 sec.) End mark
Each of the following indicators will light during playback of a tape on which Start IDs, Skip IDs and End marks
have been recorded.
* When the tape reaches the point where a Start ID is recorded, the start ID indicator will light for about 9
seconds.
* When the tape reaches the point where a Skip ID is recorded, the skip ID indicator will light for about 1
second.
* When the tape comes to the position where an End mark is recorded, the end indicator will light.
To Record Start ID's During Playback
1) Automatic recording
In this method, a Start ID is automatically recorded on the tape wherever a *level transition is detected. A Start
ID is recorded at the beginning of each segment on tapes where program numbers have not been recorded. In
the case of tapes that already contain Start ID's, the previous recording is erased and a Start ID is recorded where
the audio begins. As long as these Start ID’s are recorded, you will be able to make full use of access play and
program play functions.
* Level transition: means the audio signal must exceed the selected detection level threshold after at least 2
seconds below selected detection level. This is referenced to 0 dB, which is maximum
recording level.
1 Enter the auto mode. The pno/start ID auto indicator illuminates.
2 Press the START ID button. The start ID indicator flashes.
3 While listening to the playback sound onthe tape, advance or rewind the tape using the SHUTTLESEARCH dial.
Then, near the point where you want to insert a Start ID, press the ID WRITE button. The start ID indicator will
flash, a Start ID will be recorded where the sound begins, and the indicator will illuminate for about 9 seconds.
In this automatic program number recording mode, Start ID's about 9 seconds long will also be automatically
recorded one after another where sound begins.
To cancel the auto mode:
1 Press the STOP button. The indexing function will be released.
2 Press the PNO/START ID AUTO button. The pno/start ID auto indicator will go out.
Indexing
2) Manual recording
In this method, Start ID’s can be recorded on the tape at any desired position. Check if the pno/start ID auto
indicator is illuminated. If it is, press the PNO/START ID AUTO button to cancel.
1 Press the START ID button. The start ID indicator flashes.
2 While listening to the playback sound on the tape, advance or rewind the tape using the SHUTTLE SEARCH dial.
Then, at the point where you want to insert a Start ID, press the ID WRITE button.
The start ID indicator illuminates for about 9 seconds and then goes out. A Start ID (approx. 9 sec.) will be
recorded at the point where the button was pressed. Then the unit is ready for inserting the next Start ID.
3 Repeat steps 1-2 to insert Start ID’s one after another wherever desired.
Note: Do not press the STOP button when the start ID indicator is illuminated (approx. 9 sec.) in both Automatic/
Manual Recording. If the STOP button is pressed, the Start ID will not be recorded long enough to be
detected upon playback.
Start ID's may be recorded in either Play or Pause mode. In Play mode, they are written “on the fly” by simply
listening for the desired location. In Pause mode, more accurate cueing is possible, as the Start ID may be written
at a precise location by using Absolute Time as a reference.
Shuttle search
This function allows you to search rapidly forward or backward on the tape for specific sections with a high
degree of accuracy while listening to the material recorded on the tape. (Refer to page 12.)
Erasing Recorded Start ID’s
1 Press the START ID button. The start ID indicator flashes.
2 Turn the SHUTTLE SEARCH dial to run the tape to the point where you want to erase a start ID.
When the tape reaches the position at which a Start ID was recorded, the start ID indicator illuminates to show
the presence of a Start ID.
3 Press the ID ERASE button. The erase indicator illuminates.
The tape is then rewound to find the Start ID and erasure begins just before the beginning of the Start ID.
(During this time, the erase indicator illuminates, and the start ID indicator flashes.) After erasure, both
indicators go out.
4 Repeat steps 1-3 to erase subsequent ID's, if necessary.
Hint: — If you wish to erase all Start ID's on a tape, it is best to start at the end of the tape. By default, the unit
searches for 1D's in reverse direction during ID Erase mode.
Assigning Sequence Numbers to Recorded Start ID's
After recording or erasing of Start ID's and confirmation that all Start ID's are in the correct location, press the
RENUMBER button. The tape will rewind to the beginning, the unit searches for the recorded Start ID's, and
automatically assigns program numbers to them in sequence starting from 01. When the tape reaches the end,
the renumber function is complete, and the tape is rewound to the beginning again. While the tape is running,
the play indicator flashes. Each time the tape comes to a position where a Start ID has been recorded, the start
ID indicator illuminates.
25
Indexing
To set the first program number when renumbering:
In the stop or standby mode, use the program number buttons on the remote control transmitter to input the
program number to be renumbered first.
The program number input flashes on the program number display.
Press the RENUMBER button.
Renumbering commences, and the program numbers are re-assigned starting with the program number which
was set.
Recording Absolute Time with the Index Function (Retime Function)
Note:
Even on tapes where absolute time has not been recorded, it can be recorded while indexing is being carried out.
Enter the auto mode. The pno/start ID auto indicator will illuminate.
Press the START ID button to put the unit in Start ID recording mode. The start ID indicator will flash.
Press the REW/ REV button to rewind the tape to the beginning. Confirm that the display shows “0:00:00”.
Press the ID WRITE button.
Start ID's will be recorded on the tape automatically, together with absolute time. Audio recorded on the tape
remains unaffected.
If program numbers, Start ID's, Skip ID's and End mark have been recorded in any part of the tape, they are all
erased during a new recording.
After the absolute time is recorded up to the end of the tape or recorded part, the unit enters stop mode.
If there is a blank, unrecorded part at the start of the tape, it is necessary to run the tape in recording mode
up to the point which is already previously recorded. Otherwise, Absolute Time will not be recorded.
Recording and Erasing a Skip 1D
Note:
Skip ID causes the unit to go into fast-forward mode until the next Start ID is reached, in order to skip unwanted
material. Skip ID's can be recorded to automatically skip over parts of the tape you do not wish to hear (auto skip
play function).
Skip IDs can only be recorded manually.
The procedure to record and erase a Skip ID is the same as one for a Start ID, except for the following steps:
To enter the Skip ID recording or erasing mode, press the SKIP ID button, instead of the START ID button. The
skip ID indicator flashes.
When the ID WRITE button is pressed to record a Skip ID, the skip ID indicator will illuminate for about one
second.
Canceling the auto skip play function
26
When Skip Play Cancel is turned on, Skip ID's are ignored. When a Skip ID is encountered in this mode, the skip
ID indicator lights, but tape play continues uninterrupted.
The auto skip play mode is set ON when the power is turned on if it was on when the power was last turned off
and it is set OFF if it was off when the power was last turned off. Hence, if you want to cancel the auto skip play
function, press the SKIP PLAY CANCEL button to enter the auto skip cancel mode. The skip play cancel indicator
will illuminate.
Indexing
Recording and Erasing the End Mark
Recording the End mark
1 Afterrecording (in record standby mode), press the AUTO REC MUTE button. Approx. 4 seconds of silence will
be recorded, and the unit returns to record standby mode.
2 Press the END button. The end indicator flashes.
3 Press the PLAY button. The end indicator lights.
While the End mark is being recorded (for approx. 9 seconds), “EE” appears on the program number display.
Any recorded music at the End mark is erased.
After the End mark is recorded, the tape is automatically rewound to the beginning of the End mark, and the
unit enters stop mode.
Indexing mode of the End mark will be released automatically.
Erasing the End mark
1 Press the END SEARCH button. After the tape is rewound to the beginning automatically, the End mark will
be searched, and the unit enters stop mode. While the end search is being carried out, “EE” flashes on the
program number display.
2 Press the REC button. The rec and pause indicators illuminate.
3 Press the PLAY button. Recording starts and the End mark will be erased.
During the normal recording, the End mark will be automatically erased, so that recording can be continued.
27
28
System Display Mode Selection
System Display Mode
The 5V-3800 has several operating parameters that can be accessed by the front panel display. In system display
mode, these parameters may be checked or altered. The values set in this mode are retained when the power is
turned off.
(1) Entering the system display mode
Press the COUNTER MODE + COUNTER RESET + PAUSE buttons (=DISPLAY FUNCTION SELECTORS)
simultaneously.
Recorder is set to the digital input/output terminal selection mode (mode No.0) of system display mode.
“0-" appears on the program number display.
(2) Selecting the display mode
Press the COUNTER MODE button.
Each time the button is pressed, the display mode changes in the order of the mode number.
The mode No. of the selected display mode is displayed.
(3) Returning to the regular display (releasing the system display mode)
Press the COUNTER RESET button.
Selecting the system display mode:
Mode No. 0 = Digital input/output Mode No. 1 = Digital output
[Original display] terminals setting mode format setting mode
f f FH f f
РМО Г] 1 E _—_ | _— Г] _
UC Li UE
du NE BE JT ie Bie EF im | f Г. Г" .
ame [| 11 IT] | | cr “LL | | | HH SOE ei
ha, __J \ | J a J \, A
ль Indicates” IEC 45 4» Display returns
COUNTER coaxial terminals” to original display.
TU dm Selected. “Move | RESET.
E ba - -
Select the Release the system
a display mode. display mode.
|" | Indicates format for Indicates format for
consumer applications
taken by coaxial
and optical terminals.
commercial applications
taken by XLR-3 terminals.
Press the three
buttons simultaneously.
Mode Displays and Their Setting Methods
Selecting the digital input/output terminals (mode No.0)
Notes:
What is displayed Actual display Significance
The currently selected terminals appear on the 1) IEC-C “Coaxial terminals” selected.
counter display. “m
2) IEC-0 “Optical terminals” selected.
3) AES “XLR-3 terminals” selected.
To change the setting:
Press the SKIP button (forward). The display changes in the sequence of 1) through 3) above, thus changing the
terminals selected. The setting established after initialization is “IEC-C”.
When “IEC-C” or “IEC-0” has been selected, the digital output signals are supplied from both the coaxial
and optical terminals. When “AES” has been selected, the digital output signals are supplied from the XLR-3
terminals only.
System Display Mode Selection
Selecting the digital output mode (mode No.1)
What is displayed Actual display Significance
The output mode (format for commercial or con- 1) II Format for consumer applications
sumer applications) of the digital output terminals taken by coaxial and optical termi-
appears on the counter display. nals.
According to standards, the coaxial and optical 2) IA Format for commercial applications
terminals are for IEC consumer use. The XLR-3 taken by coaxial and optical termi-
connectors are for AES/EBU professional use. In nals.
order to increase compatibility with equipment us- ”
ing non-strandard digital interfaces, this display 3) Al Format for consumer applications
permits the format and interface connectors to be taken by XLR-3 terminals.
interchanged. For example, AES/EBU may be sent В =
tothe coaxial and optical connectors, while IECmay 4) AA Format for commercial applications
be sent to the XLR connectors. taken by XLR-3 terminals.
To change the setting:
Press the SKIP button (forward). The display changes in the sequence shown below, thus changing the output
format. The settings established after initialization are “II” for the coaxial and optical terminals and “AA” for
the XLR-3 terminals, which is the standard for IEC and AES/EBU.
I AA |—| II Al |—|1A AA |—| IA Al |
—— y "e"
Selecting the error rate display (mode No.2)
What is displayed Actual display
1) The total error rate for data played backby head “A” and “B” light on the display. The error rate is
A and head B appears on the counter display. indicated by (the value displayed /9984).
2) The error rate for data played back by head A Only “A” lights on the display. The error rate is indicated
appears on the counter display. by (the value displayed / 4492).
3) The error rate for data played back by head B_ Only “B” lights on the display. The error rate is indicated
appears on the counter display. by (the value displayed /4492).
To change the setting:
Press the SKIP button (forward). The display changes in the sequence of 1) through 3) above.
Selecting the single play mode (mode No.3)
Single play is a function which suspends playback when a Skip ID or Start ID which has been recorded is detected
during playback.
Basically, when single play mode is on, the unit will playback normally until the next Start ID or Skip ID is
encountered. The tape will then “park” in PAUSE mode so the next selection is ready for playback at any time.
To resume playback, simply press the PLAY button.
What is displayed Actual display Significance
The present single play mode setting appearsonthe 1) SP--- The single play mode has been set
counter display. | to off.
2) SP-00 The single play mode has been set
to on.
The unit operates as follows depending on the operating mode.
29
30
System Display Mode Selection
Note:
Note:
Single play mode does not take effect during Program Play, such as when programming a random sequence
of selections using the program number and MEMORY buttons on the remote control.
When a Skip ID recorded is detected during playback:
Sequence Operating mode When the single play mode is off =~ When the single play mode is on
of priority (normal)
1 *Sub code editing Playback continues. Playback continues.
mode
2 Skip play cancel Playback continues. PAUSE mode is established.
mode
3 Skip play mode The tape advances to the next Start The tape advances to the next Start 1D
ID and playback mode is estab- and pause mode is established.
lished.
When a Start ID recorded is detected during playback:
Sequence Operating mode When the single play mode is off When the single play mode is on
of priority (normal)
1 *Sub code editing Playback continues. Playback continues.
mode
2 Other mode Playback continues. PAUSE mode is established.
Cancel mode
* Sub-code editing mode: refers to when the Start ID or Skip ID indicator is flashing after either of those buttons
has been pressed.
To change the setting:
Press the SKIP button (forward). The mode is switched alternately between on and off. The setting established
after initialization is “OFF”.
Any ID recorded is ignored if it is detected during the first for two seconds after playback starts.
Selecting the program playback blank skip mode (mode No.4)
Note:
Program playback blank skip determines which way the SV-3800 recognizes the end of a program. This is
necessary for program play since the machine must skip to a selection at another location on the tape when the
currently playing program ends.
When blank skip mode is on, the machine skips to the next programmed selection as soon as it encounters audio
level below selected detection level for 2 seconds or more. When blank skip mode is off, the machine skips to
the next programmed selection as soon as it encounters the next Start ID or Skip ID following the present
program.
What is displayed Actual display Significance
The present program playback blank skip mode 1) P5-00 The program playback blank skip
setting appears on the counter display. mode has been set to on.
2) P5--- The program playback blank skip
mode has been set to off.
To change the setting:
Press the SKIP button (forward). The mode is switched alternately between on and off. The setting established
after initialization is “ON”.
If the Start ID recorded is detected at the beginning of a blank section, the blank is not skipped until the
playback of the recorded section is completed.
System Display Mode Selection
Selecting the main ID6 display (mode No.5)
(1) SCMS
The Serial Copy Management System (SCMS) is designed to control digital-to-digital DAT copying that a
consumer can perform on various digital audio material, including Compact Discs, pre-recorded DAT tapes,
and other material via [EC 958 “consumer use” digital audio interfaces (also commonly referred to as “S/P DIF”).
SCMS does not affect the ability to make copies using a DAT recorder's analog inputs and outputs.
Only one serial (or generational) digital-to-digital copy can be made from a copyright protected source, such as
a commercial CD or pre-recorded DAT. Serial Copy Management System labels are generated onto tape each
time an SC MS-equipped consumer DAT machine records an audio signal to ta pe, no matter whether the source
is from the analog or digital inputs.
(2) Setting the main ID6
Technically, the SCMS labels for DAT are encoded into the sub code sections of the main digital data area,
specifically “main 1D6”. The 5V-3800 allows the user to preset the SCMS status bits of main ID6 onto the DAT
recording. Forlegal reasons, the ID6bits are only modified ifthe sourceinputis the AES/EBU Digital I/O; analog
input during digital copying via the IEC “consumer use” input, the SV-3800 simply copies across the current
status of SCMS codes from the source tape.
What is displayed Actual Significance
display (When using consumer- type DAT recorder)
The twodigits on the left show the value 1) 00 ID6 value set to 00: Copy-free. Unlimited digital copies
of main ID6 that are user-selectable and can be made from the source tape or its copies.
will be recorded onto tape when using = |
the analog inputs or the AES/EBU Digi- 2) 11 [D6 value set to 11: Copy-restricted. Digital copies can be
tal Input terminal. The two digits on the made from the source tape with this code, but the copies
right show the actual main ID6 value cannot be duplicated digitally.
recorded on the tape.
3) 10 [D6 value set to 10: Copy-prohibited. Digital copies can-
not be made using a consumer type DAT Recorder.
Display example: When “11P00” is displayed
The first two digits denote the value of main ID6 which is
“user-selectable bits” and to be recorded onto the tape during recording.
In this case, these digits are “11.”
The last two digits denote the value of main ID6 which has been recorded
onto the tape being played back. In this case, these digits are “00.”
To change the setting:
Press the SKIP button (forward). The display changes in the sequence of 1) through 3) above, thus changing the
value of main ID6 which is to be recorded onto the tape during recording. The setting established after
initialization is “00.”
31
32
System Display Mode Selection
Setting the nominal output level (mode No.6)
Various types of audio equipment work at different reference levels. The nominal output level reduces the level
of the analog outputs. This feature makes it possible to vary the analog output level over a 14 dB range. This
virtually eliminates any likelihood of level incompatibility with other equipment.
(1) Nominal output level setting methods
This level can be set in the following 2 ways.
1) The level is set using the SKIP buttons or SHUTTLE SEARCH dial in +4 dBu to —6 dBu nominal output level
mode.
2) Thelevelissetusing FF or REW buttons for selecting +4 d Bu (changeable) or -10 dBu nominal output level mode.
(2) Setting the nominal output level
Button operated Operation Display
FF /CUE button This button establishes the mode in which the nominal Example: A 04
output level can be set to any value between +4 dBu and
—6dBu.
SKIP button (forward Each time the forward button is pressed, the setting is
Or reverse) incremented by 1 to +4, each time the reverse button is
pressed, the setting is decremented by 1to —6.
SHUTTLE SEARCH The setting is continuously incremented or decremented Бу
dial turning the dial in the REVERSE or FORWARD direction.
REW /REV button the setting is on -10dBu | A-10
System Display Mode Selection
Displaying the head cylinder rotation time (mode No.7)
This is an hour meter which increments any time the head cylinder rotates.
The total cylinder rotation time is indicated on the counter display in 5 digits (hours).
Use this as a guide to determine when your recorder needs maintenance.
Displaying the error codes, etc. (mode No.8)
The following four test results appear on the counter display.
What is displayed Description of function Actual display Significance
1) Error code Display of the system con- Example: Denotes that this is the er-
troller and mechanism con- | ror code display mode.
troller error codes. When the
cassette tray is opened, the BX XIX Xe Mechanism controller er-
error code display mode is amm Бининниырыыалай bimociial2anaazd ror code
released. | System controller error
These codes are primarily to code
aid diagnosis of any malfunc-
tion.
Refer to qualified service per-
sonnel if you should ever ex-
perience a problem.
2) Microcomputer Not available to users — д
operation mode
3) Microcomputer The version of the system con- Example: “1-00” In this case, version 1.00 is
software version troller is displayed. denoted.
To select what is to be displayed:
Press the SKIP button (forward). The display is changed in the sequence of 1) through 3) above, and the test
results are displayed.
Displaying the peak level (mode No.9)
The display of the peak level extends as far as the digit occupying the first decimal place at around the nominal
level of —18 dB (-16.8 to —19.3 dB) and around the full scale level (0 to —3 dB), and as far as the rightmost digit
of the whole number if the level is outside these ranges.
“-EE-E” appears if the peak level is exceeded. (included full scale)
Button operated Operation Display
SKIP button The peak level of the left channel is indicated if “A” is Example
(forward) displayed. When the SKIP button is pressed, “B” is dis- -18-1
played, and the peak level of the right channel is indicated. (indicates 18.1 dB)
33
System Display Mode Selection
Re-initializing all stored data settings
Press the COUNTER MODE + COUNTER RESET + PAUSE buttons simultaneously.
Now release only the PAUSE button, and press the STOP button.
All the settings except for the value indicated for the cylinder rotation time are reset to the initialized value.
When this operation is received, “00000” appears on the counter display.
List of settings which are retained even when the power is turned off
Setting to be retained Setting in the system Initialization setting
display mode
Selecting the digital input/output terminals | o LEC-C
Selecting de digital output terminals mode II AA
Setting the single play mode OFF
Setting the program play blank skip mode ON
Selecting the main [D6 to be recorded 1D6=00
Setting the monitor nominal output level +4 dBu
The total cylinder rotation time No initialization possible
ON
Setting the PNO/START 1D AUTO mode
Setting the SKIP PLAY CANCEL mode — ON
If “EEEEE” appears for 1 second on the counter display when the power has been turned on:
This indicates that the data back-up function described above is not working properly.
Condensation
Operation Notes
In winter, moisture droplets may form on the window panes of a heated room. This phenomenon is called
condensation. Condensation may occur with this unit or with cassette tape in the following situations:
* in a room where a heater has just been turned on
* in a room where steam or excessive moisture are present
* when the unit is brought in suddenly from a cold place to a warm room
* when the unit is directly in the path of cold air from an air conditioner, etc.
In such cases, the unit will not operate correctly, and even if it does operate, the tape may be damaged. In
particular, if moisture condenses on the rotating heads, the tape will stick. This will prevent the tape from
running properly, and might damage it.
If condensation occurs
To protect the tape, this unit contains a built-in device so that when condensation occurs, the dew indicator on
the display panel flashes. While the dew indicator is flashing, apart from the OPEN/CLOSE function, buttons
on the unit will not operate.
If a cassette tape is loaded in the unit, remove it and leave the power switched on. Wait until the indicator goes
out. The time required for moisture to evaporate will vary according to the environment, but it may be 60 minutes
or longer if humidity is high. Condensation usually sets in gradually, so the indicator may not flash for the first
10~15 minutes. If room temperature or humidity changes abruptly, therefore, wait for about 20 minutes before
switching on power to check that the indicator is not flashing.
Operating the unit
Always keep the cassette holder closed. If it is left open, dust will accumulate in the mechanism and cause tape
playback or recording performance to deteriorate. Do not touch the inside of the cassette holder.
The top of the recorder will become hot during use, but this is perfectly normal.
Keep the replay volume low. With DAT (Digital Audio Tape recorder) cassettes, there is much less noise than
with compact cassettes and a wider dynamic range. There will be a sudden burst of sound when the audio
material begins. As this may damage the speakers, due care should be taken. Be especially careful when using
headphones.
Dynamic Range
Dynamic range is the difference between the lowest sound level and highest sound level, and is expressed in
decibels (dB). The greater this difference, the more dynamic the recording.
When carrying or storing the unit, take care not to subject it to any severe shocks. When storing or transporting
the unit, also be sure to remove the cassette tape.
If a mechanism error occurs
Note:
This recorder unloads the tape when a mechanism error occurs in order to protect the tape. In these cases, the
unit will not operate except for the OPEN/CLOSE button. After the OPEN/CLOSE function is operated and the
tape 1s removed, the tape protection mechanism is released and all functions become valid.
(Refor to “Displaying error codes” on page 33.)
When the tape snaps or is too heavy to real up, a mechanism error occurs. In these cases, press the OPEN/
CLOSE button to open the tray and remove the cassette tape.
If this error occurs repeatedly, contact your nearest service center.
35
Quick Reference for System Display Mode Selection SV-3800
| {Sli 1 2.Selecting the 3.Changing 4.Initializing 5.Returning to
System Dis- Display the the setting the Regular
play Mode Mode Setting Display
COUNTER
MODE RESET u De
и и SELECTORS COUNTER SKIP or Ju E. COUNTER
ел. MODE | | N | A RESET
je CS
Cu) Y
| ® |
Press the COUNTER Press the COUNTER Press the SKIP button a ome Press the COUNTER
MODE + COUNTER MODE button. (forward). RESET button.
RESET + PAUSE buttons
RESET + PAUSE simultaneously, and then
buttons simultaneously. release only the PAUSE
button and press the
STOP button.
Setting in
the System
Display
Mode
Initiali-
Zation
Setting
Actual
Display
Mode
No System Mode
Significance
0 Selecting the digital IEC-C “Coaxial terminals” selected.
in output et [EC-O “Optical terminal” selected. в IEC-C O
во AES —— “XLR-3" terminals” selected.
1 Selecting the digital I Format for consumer applications
output mode taken by coaxial and optical terminals.
P LA Format for commercial applications
taken by coaxial and optical terminals. I AA
Al Format for consumer applications ® O
taken by XLR-3 terminals.
AA Format for commercial applications
taken by XLR-3 terminals.
2 5*Selecting the errorrate A and B/ The total error rate for data played
display “xxxx” back by head A and head B max. 9984. = == —
А/“хххх” The error rate for data played back by
head A max. 4992. au = =
B/“xxxx” The error rate for data played back by
head B max. 4992. _ —_
3 Selecting the single SP- —— The single play mode has been set to off. 8 SP— — — O
play mode SP-00 The single play mode has been set to on.
4 Selecting the program The program playback blank skip
lavback blank ski PS 00 mode has been set to on.
ло Е The program playback blank skip ® PS -00 О
Р5--- mode has been set to off.
5 Selecting the main ID6 00 ID6 value set to 00: Copy-free. (User-Selectable bits at the first
display 11 ID6 value set to 11: Copy-restricted two digits only)
10 ID6 value set to 10: Copy-prohibited æ 00 O
6 Setting the nominal A04~A-06 +4 to —6 dBu (Press FF button)
output level A-10 —10 dBu (Press REW button) ® A04 O
(+4 dBu)
7 Hour meter “ххххх” The total head cvlinder rotation time 15 O
indicated in 5 digits (hours). TT —
8 Displaying the error E xx” xx” “E” denotes that this is the error code a
codes. etc display mode.
д, - E operation mode a =
; , Not available to users — — —
(For diagnostic purposes "х-хх” The microcomputer software version —_
by qualified service of the system controller. a
personnel)
9 Peak level А “-хх” Lch peak level
В “-хх” Rch peak level
This page can be cut out for your convenience. After cutting it out, keep it close at hand.
38
Maintenance
To clean this unit, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth, dipped into a soap-
and-water solution or a weak detergent solution. Wring the cloth well before wiping the unit. Wipe once again
with a soft, dry cloth. Never use alcohol, paint thinner, benzine, nor a chemically treated cloth to clean this unit.
Such chemicals may damage the finish of your unit.
Importance of cleaning DAT heads
As with any tape-based recorder, it is essential that the SV-3800 Pro-DAT's heads are kept perfectly
clean. A Panasonic DAT Head Cleaning Tape (part number RT-RCLP, optional) is available for your local dealer
that automatically removes the dirt, dust and shed tape particles that gradually build up on the DAT heads.
Buthow do you know that the heads need cleaning? In extreme conditions the audio output will mute, but long
before that happens, the slow build up of dirtand oxide will “mask” the sound, and diminish the full 16-bit audio
quality from this DAT machine by causing record as well as replay errors.
An ideal solution is to make yourself a “DAT Test Tape” whose error rate you can monitor on a daily or weekly
basis (depending on how often you use the SV-3800). To prepare a Test Tape, first select a high-quality DAT
cassette and then record a series of music selections. Rewind the DAT cassette and monitor the Error Rates
during the first several minutes of tape.
Panasonic brand DAT tapes use high-quality formulations, binders, backings and calendaring process, to
provide minimum abrasiveness with maximum stability of metal particles on the tape. Itis specifically designed
to maximize head life of your DAT machine.
Check the Error Rates at several points in the tape and average the values. (On how to display error rates on the
SV-3800, see page 29.) If the Error Rates increase to around 300, a Panasonic Head Cleaning Tape can be used
as follows: Play the cleaning tape through the SV-3800 for approximately 15-20 seconds, and remove it.
DO NOT REWIND the cleaning tape, since this action might very well spread previously removed dirt and dust
onto an otherwise clean head and transport. After the Head Cleaning Tape has been used up, dispose of it
properly and start to use a new one.
If the DAT heads become very contaminated with dirt and dust, the CLEANING indicator within the display
panel will flash. In this case, use a Head Cleaning Tape as described above.
e If playback quality improves after cleaning, but then deteriorates immediately after recording or playing
back several times, the cassette tape has probably reached its useful lifetime. In this case, use a new tape.
* If sound quality does not improve even after cleaning, consult your dealer.
* Cleaning tapes cannot be used for recording or playback (be sure to read also the operating instructions
supplied with the tape).
Concerning DAT Cassette Tape
Using DAT cassette tapes
To avoid accidental erasure of valuable recordings:
Recorded tapes you want to keep can be protected by sliding the “accidental erasure prevention tab” open
towards the center of the cassette with the aid of a small screwdriver as in the diagram.
When the “accidental erasure prevention tab” To record on the tape again, return the
is open, recording cannot be performed. tab to its original position (closed).
Top surface
Cassette tapes with no accidental erasure prevention tab:
Break open the hole with a small Philips screwdriver or other tool.
With this method, however, the tape cannot be returned to its original condition, and it cannot therefore be
recorded again.
Cassette tapes exceeding 180 minutes:
These tapes are handy for their long playback and recording time, but be careful about repeatedly stopping and
starting, rewinding and fast forwarding these tapes in short intervals as they are thin, tend to stretch and may
become entangled in the deck mechanism.
Handling DAT cassette tapes
* Moisture may condense on a tape that is carried suddenly from a cold place into a warm room, so wait
about 20 minutes before using it. If the tape is used with moisture on its surface, it will be damaged.
* Do not attempt to dry a cassette tape with moisture on its surface by using a hair dryer or other appliance.
* Do not open the top lid of the cassette, pull the tape out or touch it.
* Take care not to drop the cassette, hit it or subject it to violent vibration.
* The cassette mechanism has been assembled very precisely. It should on no account be disassembled.
* The cassette cannot be used on the reverse side.
Storing DAT cassette tapes
Store the cassette in its case to prevent the entry of dust. Do not leave or store the cassette in the following
locations:
Near objects with strong magnetic fields (speakers, televisions, transformers, motors or magnets).
Places with excessive humidity (over about 80%) or dust.
Places with high temperatures (over about 35°C).
Places exposed to direct sunlight or heat from heating appliances. The cassette should never be left in a
car dashboard or near the rear window.
* After use, rewind the tape to the beginning. If rewinding is interrupted, it may lead to creases in the tape
and affect sound quality on playback.
39
Troubleshooting
Before requesting service for this unit, check the chart below for a possible cause of the problem you are experiencing. Some
simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation.
If you are in doubt about some of the check points, or if the remedies indicated in the chart do not solve the problem, refer to
the directory of Authorized Service Centers (enclosed with this unit) to locate a convenient service center, or consult your
40
dealer for instructions.
НИЕ,
Unit does not record or play cassettes
even though power is switched on.
Main Cause
Remedy
There is condensation inside unit. Wait until the dew indicator goes out.
Cassette holder does not close when a
cassette tape is loaded even if the
OPEN/CLOSE button is pressed.
Load the cassette tape in the proper
direction.
Cassette tape is not properly loaded.
No sound is output although tape is
running.
Volume control on monitor amplifier is
set at minimum.
Adjust volume using amplifier volume
control.
Monitor amplifier selector is set at a
position other than “DAT” or “TAPE”.
Set the input selector position to either
“DAT” or “TAPE” depending on the
connections to the unit.
Noise or distortion is heard on playback.
Recording level was too high or too low. Record the tape again at the optimum
level.
Heads are dirty. Clean the heads with a DAT cleaning
tape and record the tape again.
Cassette tape is worn out. Use a new cassette tape.
Analog recording cannot be performed.
Accidental erasure prevention tab on
cassette tape 15 open.
Close accidental erasure prevention tab.
Unit is not connected properly to studio Connect unit properly.
equipment.
REC LEVEL controls is set at “0”. Adjust recording (input) level with REC
LEVEL controls.
INPUT selector is set at the digital
position.
Set the INPUT selector to the analog
position.
Indexing cannot be performed.
Auto skip play cannot be performed.
Accidental erasure prevention tab on cas- Close accidental erasure prevention tab.
sette tape 15 open.
Press SKIP PLA Y CANCEL button to
turn off the indicator.
SKIP PLAY CANCEL indicator is
illuminated.
Digital signals cannot be recorded.
Search function does not operate
properly.
| Program time is not displayed properly.
Set the INPUT selector to the digital
position.
INPUT selector is set at the analog
position.
Make proper digital input/output
connections.
Digital input/output connections on
rear of unit are not correct.
Set the setting correctly referring
to page 28.
The type of digital input/output
connections do not correspond with the
settings.
Start ID has not been recorded properly. Record the Start ID, using the auto ID
function.
Add serial numbers to recorded Start
IDs.
Program numbers have not been
recorded properly.
Press REW /REV button and rewind to
start of program.
Cassette tape has been inserted midway
through a program.
Unit does not playback, record or
operate properly.
Unit was not operated in accordance
with instructions.
Switch off power, and operate again
correctly in accordance with instruc-
tions.
Signal format
Tape recording system:
Sampling frequencies
(selected automatically):
Analog input
recording
Playback/Digital
input recording
No. of quantizing bits:
No. of channels:
Specifications
Rotary head type DAT
48 kHz, 44.1 kHz
48 kHz, 44.1 kHz, 32 kHz
16-bit linear
2 (stereo)
Audio parameters (Recording and Playback
System)
Frequency response:
fs: 48 kHz
fs: 44.1 kHz
fs: 32 kHz
(only playback)
Total harmonic
distortion:
Dynamic range:
SN ratio:
Wow and flutter:
*DIN audio weighted
Remote control
Parallel remote:
Terminals
Analog input:
Input jacks
Nominal
input level
(-18 dB rec level)
Input impedance
Analog output:
Output jacks
Nominal output
level (-18 dB)
Output impedance
Headphones output:
Maximum level
Matching
impedance
10 Hz-22000 Hz (+0.5 dB)
10 Hz-20000 Hz (+0.5 dB)
10 Hz-14500 Hz (+0.5 dB)
Less than 0.03%
(+4 dBu, 1 kHz)*
Less than 0.007%
(+22 dBu, 1 kHz)*
Greater than 92 dB*
Greater than 92 dB*
Unmeasurable
(22.4 Hz to 22.4 kHz
bandpass filter)
8 pin DIN connector
(50 functions available)
XLR-3 type
+4 dBu
10k balanced
XLR-3 type
+4/-10 dBu
500 balanced
30mW+30mW (329)
860082
Digital (AES/EBU type):
Input XLR-3 type /1109 balanced
Output XLR-3 type/110 balanced
Digital (IEC type II):
Input RCA phono type
(Coaxial) /75£2, Optical
Output RCA phono type
(Coaxial) /75€2, Optical
Mechanism
Cylinder diameter: 30 mm
Cylinder rotation speed: 2000 r/min.
Tape speed:
(Normal track) 8.150 mm/s.
(Wide track: Music Tape) 12.225 mm/s.
Search speed: Up to 250 times normal playback
speed
FF/Rewind speed: Up to 250 times normal playback
speed
FF/Rewind time: Approx. 35 second
(2 hours DAT tape)
General
Power consumption: 30 W
Power supply: 60 Hz, AC 120 V
External Dimensions
(WxHxD): 430x122x315 mm
(16/;x4%,”x12%,”)
Weight: 5.9 kg (13.01b.)
Note:
Specifications are subject to change without notice.
Weight and dimensions are approximate.
+1
42
Panasonic Industrial Service...
For Audio/Video Products
in tel §, A
FANASONIC BROADCAST & TELEVISION
SYSTEMS COMPANY/DIVISION OF
MATSUSHITA ELECTRIC
CORPORATION
OF AMERICA
„PUERTO RICO
PANASONIC SALES COMPANY
(PSC)
The exact standards observed in the design and manufacture
of your Panasonic product ensure that it will need an absolute
minimum of necessary maintenance. However, should your unit
ever require service, a nationwide system of AUTHORIZED
INDEPENDENT SERVICENTERS is maintained by Panasonic
in support of your warranty.
Panasonic also has its own SERVICENTERS for Panasonic
audio/video products in the U.S. and Puerto Rico.
If service is not available in your community at this time,
carefully pack the unit, preferably in the original cartons, and
ship the product, prepaid and insured, to the most convenient
SERVICENTER.
Terms of the warranty require that the original bill of sale, or
other proof of the date of purchase must be presented when
applying for In-Warranty service.
To Locate a Convenient Authorized Servicenter
(In The U.S.A.)
DIAL TOLL FREE ovino; 800- 596- 6610
For proper assistance, tell the toll free operator you have a
Panasonic INDUSTRIAL Product
For your added convenience...in the U.S.A.
Panasonic Industrial Factory Servicenters
GEORGIA
1225 Northbrook Parkway-Suit170A
Suwanee, Georgia 30174
770-338-6855
CALIFORNIA
6550 Katella Avenue
Cypress, Calif. 90630
714-373-7450
ILLINOIS
1713 N. Randall Road
Elgin, Illinois 60123
708-468-5270
MARYLAND
54W. Gude Drive
Rockville, Maryland 20850
301-762-5125
In the unlikely event you expericence a
service problem requiring assistance from
Panasonic regarding repairs,
Please write to:
Customer Service Department
Panasonic Broadcast & Television Systems Company
Division of Matsushita
Electric Corporation of America
50 Meadowland Parkway 2A-3
Secaucus, N.J. 07094
Panasonic Service in Hawaii...
Please contact the
dealer from whom
you purchased this
product to obtain
service information.
Panasonic Service in Puerto Rico... |
Panasonic Sales Company, Division of Matsushita
Electric of Puerto Rico, Inc. ("PSC")
Ave. 65 de Infanteria, Km. 9.5
San Gabriel Industrial Park, Carolina,
Puerto Rico 00985
809-750-4300
LIMITED WARRANTY
Panasonic Broadcast & Television Systems Company or Panasonic Sales Company (collectively referred to as “Panasonic” will repair this product with
new or rebuilt parts, free of charge, in the U.S.A. or Puerto Rico in the event of a defect in materials or workmanship as follows:
1. Parts: New or rebuilt parts in exchange for defective parts for one (1) year after original purchase.**
Labor: Carry-in or mail-in service for one (1) year after original purchase.**
‘’Exceptions: Audio Head Cylinder—90 days Parts/Labor
2. Carry-in or mail-in service in the continental U.S.A. can be obtained during the warranty period from a Panasonic Regional Servicenter listed in
the Servicenter Directory. Or call 800-526-6610, toll free, to locate an authorized Panasonic Servicenter. Carry-in or mail-in service in Puerto Rico
can be obtained during the warranty period by calling the telephone numbers listed in the Servicenter Directory.
This warranty is extended only to the original purchaser. A purchase receipt or other proof of date of original purchase will be required before
warranty performance is rendered.
This warranty only covers failures due to defects in materials or workmanship which occur during normal use and does not cover damage which
occurs in shipment or failures which are caused by products not supplied by Panasonic or failures which result from accident, misuse, abuse,
neglect, mishandling, misapplication, faulty installation, set-up adjustment, improper maintenance, alteration, inadequate signal pick-up,
maladjustment of user controls, line power surges, modification of the product, or service by anyone other than a Panasonic Regional Servicenter or
authorized Panasonic Servicenter or damage that is attributable to acts of God.
LIMITS AND EXCLUSIONS
There are no express warranties except as listed above.
PANASONIC SHALL NOT BE LIABLE FOR SPECIAL, INCIDENTAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, INCLUDING, WITHOUT
LIMITATION, DAMAGE TO TAPES, RECORDS. OR DISCS, LOSS OF GOODWILL, OR ANY ASSOCIATED EQUIPMENT, DOWNTIME COSTS,
OR CLAIMS OF ANY PARTY DEALING WITH PURCHASER FOR SUCH DAMAGES, RESULTING FROM THE USE OF THIS PRODUCT OR
ARISING FROM BREACH OF WARRANTY OR CONTRACT, NEGLIGENCE OR ANY OTHER LEGAL THEORY. ALL EXPRESS AND IMPLIED
WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO
THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so
the above exclusions or limitations may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
If a problem with this product develops during or after the warranty period, you may contact your dealer or Servicenter. If the problem is not handled
to your satisfaction, then write to the Consumer Affairs Division at the company address indicated on the Panasonic Servicenter list.
43