450 Series

Mechanical Baby Scale

Owner’s Manual

8525-M058-O1 Rev E y 450 Series Owner’s Manual 1

2 8525-M058-O1 Rev E y 450 Series Owner’s Manual

INTRODUCTION

The Detecto 450 Series Mechanical Baby Scale is ideal for use in health clinics and medical practices for height and weight measurement of pediatric patients. The scale is durable, having a sturdy enameled steel scale base, a built-in measuring tape (up to 21 in / 53 cm) to allow the healthcare professional to measure both weight and height simultaneously, and an easy-toclean polystyrene tray that cradles babies securely.

This manual is provided to guide you through assembly and operation of your scale. Please read it thoroughly before attempting to assemble or operate your scale and keep it available for future reference.

This manual is for use with the following Mechanical Baby Scale models:

450 451

COPYRIGHT

All rights reserved. Reproduction or use, without expressed written permission, of editorial or pictorial content, in any manner, is prohibited. No patent liability is assumed with respect to the use of the information contained herein.

DISCLAIMER

While every precaution has been taken in the preparation of this manual, the Seller assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from use of the information contained herein. All instructions and diagrams have been checked for accuracy and ease of application; however, success and safety in working with tools depend to a great extent upon the individual accuracy, skill and caution. For this reason, the

Seller is not able to guarantee the result of any procedure contained herein. Nor can they assume responsibility for any damage to property or injury to persons occasioned from the procedures. Persons engaging the procedures do so entirely at their own risk.

8525-M058-O1 Rev E y 450 Series Owner’s Manual 1

UNPACKING

Remove the scale base, column with weigh beam headpiece, baby tray, and hardware kit from the shipping carton. After removing from the carton, check for any damage that may have occurred during shipment. Note that the purchaser is responsible for filing all claims for any damages or loss incurred during transit. Keep and use the original carton and packing material for return shipment if it should become necessary .

Small Poise

Weigh Beam

Large Poise

Column

Baby Tray

with built-in

Measuring

Tape

Scale Base

SPECIFICATIONS

Capacity:

130 lb x 1 oz 65 kg x 20 g

Measuring Tape: 0 to 21 in x 0.25 in (0 to 53 cm x 0.1 cm)

Platform Dimensions: 14.75 in x 10.75 in (37.5 cm x 27.3 cm)

Tray Dimensions: 22 in W x 14.75 in D x 4.5 in H (56 cm W x 37 cm D x 11 cm H)

2 8525-M058-O1 Rev E y 450 Series Owner’s Manual

SCALE ASSEMBLY

The Detecto 450 Series Mechanical Baby Scale comes partially assembled. The following components require assembly: x Column x Draft Rod x Baby

Tools required: x Phillips head screwdriver x Wrench

1. Set the scale base on a table or other assembly area free from traffic and obstructions.

2. Remove the cable tie that secures the draft rod during transit (shown in Figure 1).

Cable Tie

Draft Rod

Figure 1. - Remove cable tie securing draft rod in column

3. Insert the column onto the scale base (shown in Figure 2), ensuring that the DETECTO logo on the weight beam faces the scale base.

Column

Scale Base

Figure 2. - Insert column onto scale base

8525-M058-O1 Rev E y 450 Series Owner’s Manual 3

SCALE ASSEMBLY, CONT.

4. Using a Phillips screwdriver, install the eight screws and washers to secure the column to the scale base as shown in Figure 3.

Figure 3. - Install eight screws and washers to secure column to scale base

5. Lay the scale on a table. Remove and discard the shipping tie wrap wires on the underside of the scale base as shown in Figure 4.

Figure 4. - Lay scale on table to access bottom of scale base

4 8525-M058-O1 Rev E y 450 Series Owner’s Manual

SCALE ASSEMBLY, CONT.

6. Insert the wrench (included) into the small hole in front of the draft rod and pull the draft rod hook with the wrench to connect it to the long lever as shown in Figure 5. The draft rod is located inside the scale column. Once the column is attached to the scale base, the draft rod must be attached to the long lever.

Draft Rod Hook

Long

Lever

Insert wrench here

Figure 5. - Connect draft rod hook to long lever

7. Push the long lever forward and hook the draft rod’s hook onto the long lever pivot.

IMPORTANT! During shipping, a plug is installed to ensure that the shelf lever assembly stays aligned, however the linkage may still come out of alignment.

Remove the plug and then visually ensure that the shelf lever assembly linkage is centered and properly aligned. The linkage must be free floating in order for the scale to weigh properly. If the scale is slightly tipped to one side, the linkage can be seen by looking up underneath the weigh beam headpiece.

Remove shipping linkage alignment plug

Shelf lever assembly linkage must be properly aligned in order to weigh

Figure 6. - View of linkage underneath weigh beam headpiece

8. Place the scale gently back on the floor.

8525-M058-O1 Rev E y 450 Series Owner’s Manual 5

SCALE ASSEMBLY, CONT.

9. Attach baby tray to scale platform using the two (2) flat head screws provided. Do not overtighten screws.

Attach baby tray with (2) provided flat head screws.

Figure 7 - View showing attachment of baby tray to scale platform base.

6 8525-M058-O1 Rev E y 450 Series Owner’s Manual

BALANCING THE SCALE

After assembly, the scale must be balanced prior to use.

1. Ensure the scale is sitting on a level surface, and slide both the small and large poise to zero (far-left position on the weigh beam).

2. Gently hold the beam pointer with your finger so it is centered within the trig loop area.

Release the beam pointer and let it rise freely up or down.

3. If the beam pointer doesn’t remain centered, turn the balance screw (shown in Figure 8) to the right or left using a flathead screwdriver until the beam pointer remains centered within the trig loop.

Small Poise

Large Poise

Balance

Screw

Weigh Beam

Beam Pointer

Trig Loop

Figure 8 - View showing components for balancing scale prior to normal operation.

8525-M058-O1 Rev E y 450 Series Owner’s Manual 7

OPERATING THE SCALE

The following steps will guide you through the operation of your 450 Series, Weigh Beam

Neonatal Scale. Refer to Figure 9 below when performing the steps.

CAUTION!

Do not leave the baby unattended in the baby tray.

Failure to maintain continual control of the baby can result in serious injuries should the baby fall from the baby tray.

1. Move both poises to the Zero position. Be sure the Beam Pointer is in the center of the opening in the Trig Loop.

2. Slide the Large Poise to the approximate weight. For example, if the patient weighs approximately 20 pounds, slide the Large Poise to 10 pounds.

3. Place the patient on the scale; and then slide the Small Poise to 5 pounds.

4. Continue sliding the Small Poise until the Beam Pointer is centered in the Trig Loop opening.

5. Read the Small Poise at the pointer and add to the 10 pounds from the Large Poise. For example, if the pointer is at 8 pounds, the patient weighs 18 pounds.

Small Poise

Beam Pointer centered in

Trig Loop

Large Poise

Trig Loop

Figure 9 - View showing procedure for weighing operation.

8 8525-M058-O1 Rev E y 450 Series Owner’s Manual

TROUBLESHOOTING

The Detecto 450 Series Mechanical Baby Scale is factory-calibrated to within plus or minus

1 ounce (20 grams) accuracy. For the most accurate readings, always use the scale on a hard, level surface and stand in the center of the scale platform with the weight evenly distributed. If an error occurs or seems excessive, check the following:

Problem

Zero balance out of adjustment

Possible Solution x The weighing beam must be balanced so the beam pointer comes to a rest in the center of the trig loop when both the small and large poise are set at zero (far-left position). Refer to Figure 8 and the BALANCING THE SCALE instructions.

Beam does not move freely

Platform rocks excessively

Beam does not move at all during weighing

Scale is out of calibration x Make sure the beam pointer is not touching the side of the trig loop, impeding its range of travel. x Visually ensure that the linkage is centered and properly aligned. Occasionally during shipping, the alignment will become skewed. The linkage must be free floating in order for the scale to weigh properly. If the scale is slightly tipped to one side, the linkage can be seen by looking up underneath the weigh beam headpiece. x Ensure the scale is setting on a level surface. When you push down on any corner of the platform, you should not feel any significant rocking. x Small and large poise are set higher than the person’s actual weight. Reset the both poises to a lower or zero weight. x Make sure the draft rod is properly connected and aligned as shown in Figure 5. x Recalibrate the scale by placing a known weight on the scale and turning the balance screw until the pointer remains centered within the trig loop.

8525-M058-O1 Rev E y 450 Series Owner’s Manual 9

REPLACEMENT PART IDENTIFICATION

10 8525-M058-O1 Rev E y 450 Series Owner’s Manual

1

2

3

4

5

7

1

1

1

1

1

1

1

REPLACEMENT PART IDENTIFICATION, CONT.

Description

0033-0551-0A BEAM ASSY, 130 LB X 1 OZ, MODEL 450

0033-0550-0A BEAM ASSY, 65 KG X 20 G, MODEL 451

0033-0538-08 BEAM YOKE COVER

0033-0539-0A BEAM YOKE ASSY

0033-0540-08 SHELF LEVER HANGER

0033-0553-0A DRAFT ROD AND SHELF LEVER SHORT COLUMN

0033-0544-0A PLATFORM AND PLATFORM BEARING

8525-M058-O1 Rev E y 450 Series Owner’s Manual 11

12

STATEMENT OF LIMITED WARRANTY

Detecto Scale warrants its equipment to be free from defects in material and workmanship as follows: Detecto warrants to the original purchaser only that it will repair or replace any part of equipment which is defective in material or workmanship for a period of two (2) years from date of shipment . Detecto shall be the sole judge of what constitutes a defect.

During the first ninety (90) days Detecto may choose to replace the product at no charge to the buyer upon inspection of the returned item.

After the first ninety (90) days, upon inspection of the returned item, Detecto will repair or replace it with a remanufactured product. The customer is responsible for paying for the freight both ways.

This warranty does not apply to peripheral equipment not manufactured by Detecto; this equipment will be covered by certain manufacturer’s warranty only.

This warranty does not include replacement of expendable or consumable parts. This does not apply to any item which has deteriorated or damaged due to wear, accident, misuse, abuse, improper line voltage, overloading, theft, lightning, fire, water or acts of God, or due to extended storage or exposure while in purchaser’s possession. This warranty does not apply to maintenance service. Purchased parts will have a ninety (90) day repair or replacement warranty only.

Detecto may require the suspect product to be returned to the factory; item(s) must be properly packed and shipping charges prepaid. A return authorization number must be obtained for all returns and marked on the outside of all returned packages.

Detecto accepts no responsibility for loss or damage in transit.

8525-M058-O1 Rev E y 450 Series Owner’s Manual

STATEMENT OF LIMITED WARRANTY

Conditions Which Void Limited Warranty

This warranty shall not apply to equipment which:

A.) Has been tampered with, defaced, mishandled or has had repairs and modifications not authorized by Detecto.

B.) Has had serial number altered, defaced, or removed.

C.) Has not been grounded according to Detecto’s recommended procedure.

Freight Carrier Damage

Claims for equipment damaged in transit must be referred to the freight carrier in accordance with freight carrier regulations.

This warranty sets forth the extent of our liability for breach of any warranty or deficiency in connection with the sale or use of the product. Detecto will not be liable for consequential damages of any nature, including but not limited to, loss of profit, delays or expenses, whether based on tort or contract. Detecto reserves the right to incorporate improvements in material and design without notice and is not obligated to incorporate improvements in equipment previously manufactured.

The foregoing is in lieu of all other warranties, express or implied including any warranty that extends beyond the description of the product including any warranty of merchantability or fitness for a particular purpose. This warranty covers only those Detecto products installed in the forty-eight (48) contiguous continental

United States.

Ph. (800) 641-2008

E-mail: [email protected]

203 E. Daugherty

Webb City, MO 64870

08/27/2014

Printed in USA

D268-WARRANTY-DET-A

8525-M058-O1 Rev E y 450 Series Owner’s Manual 13

14

Cardinal Scale Manufacturing Co.

102 E. Daugherty, Webb City, MO 64870 USA

Ph: 417-673-4631 or 1-800-641-2008

Fax: 417-673-2153

Technical Support: 1-866-254-8261

E-mail: [email protected]

8525-M058-O1 Rev E y 450 Series Owner’s Manual