Shimano ST-5500 Shifting/Brake Lever Service Instructions

SERVICE INSTRUCTIONS SI-59GOA
Front derailleur
FD-5500
Before use, read these instructions carefully, and follow them for
correct use.
In order to realize the best performance, we
recommend that the following combination be used.
Series SHIMANO105
Shifting lever ST-5500
Outer casing SP40
Gears 18
Front derailleur FD-5500
Front chainwheel FC-5500
Bottom bracket BB-5500 UN
Rear derailleur RD-5500
Freehub FH-5500
Cassette sprocket CS-HG70-9
Chain CN-HG72
Bottom bracket cable guide SM-SP17 2
Type Band type / Brazed on type
Front derailleur
installation band diameter S (28.6mm). M (31.8mm)
Chainstay angle («) 61° - 66°
Chain line 43.5mm
Note
* For smooth operation, always be sure to use the specified
outer casing and the bottom bracket cable guide. 4.
* Grease the inner cable and the inside of the outer casing
before use to ensure that they slide properly.
* For any questions regarding methods of installation,
adjustment, maintenance or operation, please contact a
professional bicycle dealer.
Installation of the front derailleur
1. Adjust so that the clearance
between the chain guide outer
plate and the large gear is
NS Cesare: 1-3mm
- . x A
1 - 3 mm before installing. ГО,
=
ADS >
©
“En
SHA
<
Chain guide outer plate
2. The level section of the chain
guide outer plate should be Г
directly above and parallel to | LI
||
8 Chainwheel
the largest chainring. el] (largest chainring)
D | AN
a MW
3. Secure using a 5mm Allen key.
Chain guide
U
These service instructions are
printed on recycled paper and
can be recycled again
SHIMANO
SHIMANO AMERICAN CORPORATION
One Holland Irvine CA 92618 U.S.A. Phone 714-951-5003
SHIMANO EUROPA
ED
SHIMANO INC.
1.
2. Connection and securing of cable
. Top adjustment
SIS adjustment
Low adjustment
Set so that the clearance between the
chain guide inner plate and the chain is
0-0.5 mm.
Largest
sprockat Inner ring
Chain guide
inner plate
While pulling the inner cable, tighten the wirw fixing bolt
with a 5 mm allen key to secure the cable.
/ After taking up the initial slack in
the cable, re-secure to the front
derailleur as snown in the |
Pull illustration.
Set so that the clearance between the
chain guide outer plate and the chain
is 0-0.5 mm.
Smallest
sprocket
=
Quter ring
(>
adjustment
ВСТР
2 нано
CT ET AA ET TE
Adjustment of the cable |
tention
(1) Set the chain to the largest
rear sprocket, and shift the
front to top gear.
Largest
sprocket
Lever ®
From large chainring
to small chainring
Lever @
From small chainring
to large chainring
Lever ©
Quier ring
Levor (a)
(2) Perform the trimming. Ш Trimming (noise-prevention
mechanism)
Gently press the lever b).
(A “click” sound will be heard.)
(3) After trimming, adjust the clearance (by using
the cable-adjustment bolt) of the chain and chaib
guide yo the minimum (0-0.5mm).
Clearance:
0-0.5mm
7
Outer ring
Chain guide
inner plate
Chain
Outer casing adjustment barrel
Be sure to read these service instructions in conjunction with the service instructions for
the ST-5500 before use.
Indusineweg 24 NL-8071 CT Nunspesl Holland Phone 31-3412-72222 77 Oimalsu-cho 3-cho Sakai Osaka 580-8577 Japan Phone 0722-23-3243
Please note: specifications are subject to change for improvernent without notice. (English)
O Mar, 1998 by Shimano Inc. XBC SZK Printed in Japan.