advertisement
VSP 112U Quick Start
Max 2048×1152@60Hz/2560×1152×50Hz output resolution
User-defined resolution adjustment
Built in with the 3
rd
generation media player
Playlist schedule for 30 days and 24 hours running
Seamless switching between different inputs
Audio and video sync
De-embedded for USB, HDMI inputs
2 LED full color sending card install slot
CONTENT
Product Introduction
2
Packing Configuration
3
Hardware Orientation
4
Operating Instruction
6
How to Realize Single Image Switching
..............................................................................................
How to Set up the Size and Position of the Single Image
................................................................
Contact Information
14
1
Address
:
S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: 00865925771197
Email: [email protected]
Fax:00865925771202 http://www.rgblink.cn
Product Introduction
VSP 112U is one of the most basic LED audio
& video processor developed by RGBlink, it supports inputs including 2×composite (CVBS),
2×VGA (VGA1 compatible with YPbPr), 1×DVI,
2×USB (for playing media files, including video and graphic), 4×balanced analog audio, and outputs including 2×DVI, 1×VGA (Via DVI2+
VGA OUT port) and 1×balanced analog audio.
VSP 112U integrates with advance broadcast quality motion adaptive de-interlacing engine, natural color reproduction and dynamic range adjustment capacity, and enhances pixel based scaling especially for splicing function.
VSP 112U builds in with the 3 rd generation media player for strengthen full HD quality media reproduction and schedule ability. This features its marketing range from installation, rental & stage and branding advertisement.
System Connection
RGBlink offers solutions to demanding technical problems.
Any application questions, or required further information, please contact with our customer Support Engineers.
VSP 112U System Connection Diagram
2
Address
:
S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: 00865925771197
Email: [email protected]
Fax:00865925771202 http://www.rgblink.cn
Packing Configuration
Power Cord
USB Cable
DVI-D Cable
USB Disk
Screw Driver
Antistatic Bag
Certification
Note:
Chinese Standard, American Standard or European Standard power cord is option.
The color of the screw driver is randomly when packing.
3
Address
:
S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: 00865925771197
Email: [email protected]
Fax:00865925771202 http://www.rgblink.cn
Hardware Orientation
Front Panel
Button Instruction
MENU
SAVE
LOAD
Menu and return reuse button
Save button
Load button
Stop or play button
Move Previous button
Mover Next button
CV1,CV2
VGA1,VGA2
DVI
USB1
CVBS signal source button
VGA signal source button
DVI signal source button
FREEZE
0~9
OLED Panel
USB video signal source button Knob
Freeze button
Number button, use for scale and custom setting
Show operation menu items
Confirm and adjust OLED menu
SCALE Scale button
4
Address
:
S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: 00865925771197
Email: [email protected]
Fax:00865925771202 http://www.rgblink.cn
Back Panel
Input Interface
2~9 Audio Input Port
19 USB Input Port
20.21
CVBS Input BNC Port
1. 22
23
VGA Input DB15 Port
DVI Input DVI-I Port
Output Interface
10 Audio Output Port
24
25
DVI Output DVI-I Port
DVI+VGA DVI-I Output
Other Interface
11 Dial Switch
12 USB Interface of Device USB-B Port
13 RS232 Interface
14.15.26.27
10/100M Interface RJ45
16.28
17.29
USB Interface of Sending Card
DVI Input Port of Sending Card
18
30
Switch
Power IEC-3
5
Address
:
S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: 00865925771197
Email: [email protected]
Fax:00865925771202 http://www.rgblink.cn
Operating Instruction
Content
How to Set up the USB Playlist
How to Do Customized Output Resolution
How to Realize Single Image Switching
How to Set up the Size and Position of Signal Image
How to Realize Test Pattern Output and Settings
How to Realize the Screen Size Setting
How to Realize the Text Overlay Setting
How to Load the Saved Parameter
6
Address
:
S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: 00865925771197
Email: [email protected]
Fax:00865925771202 http://www.rgblink.cn
How to Set up the USB Playlist
1. Copy the video files to the USB, and then insert the USB to the computer.
2. Double click the software ”AVDSP Console 3.1.6.6”.
3. Click “VProcessor” menu, and choose “USB Play List” option, pop up the USB Player interface.
4. Choose the file type as “Picture” or “Video”.
5. Click “Scan USB” to scan the files in USB, USB Player will rename the files, that is add serial number.
6. Click the date on the left side, and choose the broadcast date, then set the Play Time and Total Play
Time. After setting, click "Add". Then double click the file on the right side, and add the file to the play time that just set. User can also delete the file in play time by double-clicking the file on the middle area. Repeat the above operations, add other play time, and click "Modify", "Delete" to modify or delete the file.
7. For the day play list that already set, users can click the right mouse to copy to day, week, month, or choose the date that need to copy, push "Ctrl + C” to copy, and push "Ctrl + V" to paste to the date.
8. After setting up the playlist, click "SAVE", and name the file as PLAYLIST. Bin.
9. Copy the PLAYLIST.bin file to the USB.
10. Insert the USB to the USB1 port in VSP 112U, reboot the device.
11. Set the date and time for VSP 112U: push the [MENU] button to enter to the menu items, choose
<SYSTEM>, push the knob to confirm, turn the knob, and choose <DATE&TIME>, set the time as current time. Then choose USB1, enter the USB menu items, choose Play Order, push the knob to confirm and then choose PLAYLIST, USB playlist setting is finished.
7
Address
:
S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: 00865925771197
Email: [email protected]
Fax:00865925771202 http://www.rgblink.cn
How to Do Customized Output Resolution
1. Push [MENU] button to enter the menu items, turn the knob and go to <OUTPUT FORMAT>, push the knob and confirm to go into the <OUTPUT FORMAT> menu.
2. Push the knob and go into <CUSTOMIZED> menu.
3. Turn the knob on each digital position, and change the value of the digital by the digital buttons on the front panel.
4. After the digital, push the knob will add ×, means before the × is the horizontal size. Same operation for vertical size.
5. After the digital, push the knob will add @, means before the @ is the vertical size, and after the @ is the refresh rate. Only digital 50 or digital 60 supports for the refresh rate. Use the digital buttons to finish the settings.
6. After input all the values, push knob to enable VSP 112U to output this resolution. VSP 112U will take 5 to 10 seconds to enable this output resolution.
How to Realize Single Image Switching
1. Boot the system default CV1 to the current input source, if need seamless switching other source such as DVI, push the DVI button.
2. CV1 button light turns off after pushing DVI button. DVI button light is on if the DVI signal is effective and stable. And if the DVI signal is invalid or no input, DVI button light will flash.
Note:
Seamless switch means signal switch will not appear any flash point, black, shaking or delay.
8
Address
:
S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: 00865925771197
Email: [email protected]
Fax:00865925771202 http://www.rgblink.cn
How to Set up the Size and Position of the Single Image
Push the [SCALE] button and enter to the SCALE function menu. The button 0~9 are on, user can adjust the size by the knob or number buttons.
H SIZE: Width setting.
V SIZE: Height setting.
H POS: Horizontal phase setting.
V POS: Vertical phase setting.
RESET: If image quality distorts by improper operation, it can be recover by reset.
How to Set up the PIP
Push the [MENU] button, and choose <PIP>, push the knob to confirm. Choose PIP, and set “ON” to enable the PIP function.
LAYOUT: User can choose 7 kinds of PIP layouts, here we take 3 layouts for example. The corresponding results are as follows:
PIP L+T PBP L+R PBP T+B
SWAP IMAGE: It can set PIP to swap exchange, when choose ON, it can realize the Image A and
Image B switching.
SELECT: Can choose to set the size or position of IMAGE A or IMAGE B individually.
9
Address
:
S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: 00865925771197
Email: [email protected]
Fax:00865925771202 http://www.rgblink.cn
How to Set up Image Zoom
The image can be zoom in horizontal or vertical separately, to meet the special effects required.
Push the [MENU] button to go into the menu items, and turn the knob to go to ZOOM menu and push the knob to confirm to go into ZOOM menu items as following:
V UP--
Zoom in vertical and the image will be zoom in to the top direction from its bottom.
V DOWN--
Zoom in vertical and the image will be zoom in to the down direction from its top.
V UP/DOWN--
Zoom in vertical but in both top and down direction from its middle.
H LEFT--
Zoom in horizontal and the image will be zoom in to the left direction from its right.
H RIGHT--
Zoom in horizontal and the image will be zoom in to the right direction from its left.
H LIFT/RIGHT--
Zoom in horizontal but in both left and right direction from its middle.
CENTER--
Zoom in 4 corner direction from center.
How to Realize Test Pattern Output and Settings
Test Pattern is used to calibrate the screen or system, especially when there is not standard input measure instrument. There are 66 kinds of test patterns for VSP 112U.
1. Push the [MENU] button and go into the main menu, turn knob and go to <SYSTEM> menu.
2. Push the knob and go into the <SYSTEM> menu. Turn the knob and go to <DISPLAY MODE> menu.
3. Push the knob and go into the <DISPLAY MODE> menu. Turn the knob and go to <PURE COLOR> or <TEST PATTERN> option.
<FLAT COLOR>: Push the knob and go into the menu, RED color range is from 0~255, GREEN is from
0~255, and BLUE is from 0~255.
<TEST PATTERN>: Push the knob and go into the menu, there are 66 kinds of test pattern options ready. If set the Test Pattern enable as auto switching mode. VSP 112U will output all the Test Pattern one by one, and the interval between each is 1-10S.
10
Address
:
S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: 00865925771197
Email: [email protected]
Fax:00865925771202 http://www.rgblink.cn
How to Realize the Screen Size Setting
VSP 112U supports the screen parameters to meet the requirement where user want to switch between scale screen size and full display size (like monitor). This is only enable for a single display window.
Following is an example of a screen size is1408 x 832.
Operator can defined the VSP 112U output resolution from standard output resolution list or customized the output resolution which is higher than1408 x 832. For this application 1440x900 is an example:
Push the [MENU] button to go into the menu items, and turn the knob goes to <SCREEM
PARAMETER>, push the knob and goes into the <SCREEN PARAMETER> menu as following:
H SIZE--
Horizontal pixels, turn the knob and use the digital button to input the value1408.
V SIZE--
Vertical pixels, turn the knob and use the digital button to input the value 832.
H POS--
Horizontal position, default value is 0, set the value as the way H SIZE and V SIZE.
V POS--
Vertical position, default value is 0, set the value as the way H SIZE and V SIZE.
MODE--
Mode option, enable SCREEN SIZE.
11
Address
:
S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: 00865925771197
Email: [email protected]
Fax:00865925771202 http://www.rgblink.cn
How to Realize the Text Overlay Setting
Before setting the text overlay, please make sure the input channel of the text. For example, set VGA input as the text channel. Then make sure the channel that the text will overlay, for example, overlay the text on CV1 channel. The operations are as follows:
1. Push VGA button to make sure there is VGA input.
2. Push CV1 button to make sure there is CV1 input.
3. Push the [MENU] button, turn the knob, and choose <TEXT OVERLAY>, push the knob to confirm.
Then enter into <TEXT OVERLAY> menu items, turn the knob, and choose <TEXT OVERLAY>, push the knob to confirm, turn the knob again, and choose “ON” to enable the text overlay function.
4. Make sure VGA input is IMAGE B, and CV1 input is IMAGE A, if not, choose <SWAP WINDOW> option in <PIP>, and choose “ON” for <SWAP WINDOW>.
5. That is, choose the VGA image in “IMAGE B” in <SELECT> in <PIP> menu, and push [SCALE] button to adjust the size and position of VGA image, then set the VGA image to the required position.
The standard position and size is: ensure the VGA image overlay on the CV1 image, display normally and without black edges. If there are black edges around VGA image, choose <ZOOM> option in
<PICTURE> to adjust.
6. Set the text overlay mode: choose <PRESET> option in <TEXT OVERLAY>, push the knob to enter into the <PRESET> menu items. Turn the knob to choose the preset mode, for example, set the VGA text as WhOnBk, choose WhOnBk1 or WhOnBk2 (Note: Text Overlay only support monochrome subtitles), user can also adjust the <BLEND MODE> or <BLEND LEVEL> to get a better effect.
7. Push the [SAVE] button to save the above parameters.
12
Address
:
S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: 00865925771197
Email: [email protected]
Fax:00865925771202 http://www.rgblink.cn
How to Save the Parameter
Save user mode to the customer for different scene directly call, leave out the edit operation inconvenience, VSP 112U provides ten save preferences.
1. Push the [SAVE] button, the button light is on, and some of 0~9 buttons are on and some are flashes.
Button is on can be saved, and button flashes will be overwrite. Push the button on to save.
2. Push the [MENU] button to disable the SAVE function.
How to Load the Saved Parameter
Save user mode to the customer for different scene directly call, leave out the edit operation inconvenience, VSP 112U provides ten save preferences.
1. Push the [LOAD] button, the light of button 0~9 is on or flash, the button on is ready for recall and flash means just recall.
2. Push the button on to recall.
3. Push the [MENU] button to disable the LOAD function.
13
Address
:
S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: 00865925771197
Email: [email protected]
Fax:00865925771202 http://www.rgblink.cn
Contact Information
Warranty:
All video products are designed and tested to the highest quality standard and backed by a full 3-year parts and labor warranty. Warranties are effective upon delivery date to customer and are non-transferable. RGBlink warranties are only valid to the original purchase/owner. Warranty related repairs include parts and labor, but do not include faults resulting from user negligence, special modification, lighting strikes, abuse(drop/crush), and/or other unusual damages.
The customer shall pay shipping charges when unit is returned for repair.
Headquarter:
S603~604 Weiye Building Torch Hi-Tech Industrial Development Zone
Xiamen, Fujian Province, P.R.C
● Tel:
+86-592-5771197
● Fax:
+86-592-5771202
● Customer Hotline
:
4008-592-315
● Web:
~ http://www.rgblink.com
~ http://www.rgblink.cn
● E-mail:
14
Address
:
S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: 00865925771197
Email: [email protected]
Fax:00865925771202 http://www.rgblink.cn
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 Front Panel
- 6 Back Panel
- 7 Content
- 8 How to Set up the USB Pla
- 9 How to Do Customized Out
- 9 How to Realize Single Image
- 10 How to Set up the Size and
- 10 How to Set up the PIP
- 11 How to Set up Image Zoom
- 11 How to Realize Test Pattern
- 12 How to Realize the Screen
- 13 How to Realize the Text O
- 14 How to Save the Parameter
- 14 How to Load the Saved Para