Viking Range DMOS200 Conventional Microwave Oven Installation instructions
Add to my manuals4 Pages
Viking DMOS200 is a built-in microwave oven designed for seamless integration into your kitchen cabinetry. With a spacious 2.0 cu. ft. capacity, it offers ample room to accommodate a variety of dishes. The intuitive control panel allows for precise cooking with features like power level adjustment, cooking time selection, and pre-programmed settings for common foods. Enjoy the convenience of hands-free operation with the automatic door opening function.
advertisement
INSTALLATION
INSTRUCTIONS
DESIGNER SERIES
MICROWAVE BUILT-IN TRIM KIT
Retain for Future Reference
VIKING RANGE CORPORATION
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
IMPORTANT - PLEASE READ AND FOLLOW
• Before beginning, please read these instructions completely and carefully.
• Be sure to DISCONNECT THE PLUG of the microwave oven from the electrical outlet before installing the built-in trim kit.
Remove the turntable from the oven cavity.
• Because the kit includes metal parts, caution should be used in handling and installation to avoid the possibility of injury.
• Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.
• Please observe all local and national codes and ordinances.
• The installer should leave these instructions with the consumer who should retain for local inspector’s use and for future reference.
THIS BUILT-IN TRIM KIT IS DESIGNED FOR USE ONLY WITH VIKING MICROWAVE OVENS SPECIFYING BUILT-IN
TRIM KIT DMTK271 OR DMTK301 ON THE RATING LABEL ON THE LEFT SIDE WALL OF THE OVEN CAVITY.
IF YOUR LOWER CONVENTIONAL OVEN IS NOT LISTED IN THE USE AND CARE MANUAL OF THE MICROWAVE
OVEN, THEN DO NOT INSTALL THE MICROWAVE OVEN ABOVE IT OR IN ANY AREA WHERE HEAT AND STEAM
ARE GENERATED; FOR EXAMPLE, NEXT TO OR ABOVE A CONVENTIONAL RANGE.
PARTS INCLUDED IN THE KIT
1) Frame Assembly 2) Bottom Duct Assembly: QTY 1
Back Frame
QTY 1
Front Frame
QTY 1
3) Screw A (1-3/16" length): QTY 2 4) Screw B (1 3/4" length): QTY 4
NOTE:
SIDE FLANGES ON
DMTK301 ONLY .
5) Template: QTY 1
Maximum Cutout Opening Width 24 11/16" (627.06 mm)
Minimum Cutout Opening Width 24 3/8" (619.13 mm)
1. Align the mounting template center line with the center of the cutout and the floor line with the floor of the cutout.
Tape it into place.
2. For DMTK271, predrill 4 holes marked with a HP " drill bit.
For DMTK301, predrill 4 holes marked
3. Remove template from the cabinet
with a HP " drill bit.
Center Line
Distance between holes 28 5/8" (727.3 mm)
14 5/16" (363.475 mm)
Distance between holes
12 13/16" (325.4 mm)
25 5/8" (650.75 mm)
Floor Line of Cutout Opening 29/32" (23.4 mm)
TINSKB110MRR0
CABINET OR WALL CUTOUT
Cutout Dimensions
Height (A)
Width (B)
Depth (C)
Minimum 16 3 / 4 " (4.5 cm)
Maximum 17" (43. cm)
Minimum 4 3 / 8 " (61.9 cm)
Maximum 4 11 / 16 " (6.7 cm)
Minimum 0" (50.8 cm)
Illustration 1
A
ELECTRICAL OUTLET LOCATION
Outlet should NOT be in the shaded area as indicated on Illustration 1.
NOTE 1: If the Depth (C) dimension is greater than 1"
(53.3 cm), the outlet location may be in any area on the rear wall.
NOTE 2: The floor of the opening should be constructed of plywood strong enough to support the weight of the oven and floor load (approximately 100 pounds). The floor should be level for proper operation of the oven.
Be sure to check the local building code as it may require that the opening be enclosed with side, ceiling and rear partition. The proper functioning of the oven does not require the enclosure.
Illustration 2
B
MOUNTING TEMPLATE
1. Align the mounting template center line with the center of the cutout and the floor line with the floor of the cutout. Tape it into place.
. For DMTK271 , only predrill 4 holes marked “A” with a 1/16" drill bit. For DMTK301 , only predrill 4 holes marked “B” with a 1/16" drill bit.
3. Remove template from the cabinet
MAKE FLANGES
FLUSH
SCREW A
Illustration 3
BOTTOM
DUCT ASSEMBLY
4"(10.2 cm
)
6"(15.2 cm
)
C
4"(10.2 c m)
NOTE:
SIDE FLANGES ON
DMTK301 ONLY .
BOTTOM DUCT ASSEMBLY
1. Place the Bottom duct in the opening. When the Bottom
Duct Assembly is in the opening correctly, the flanges will be tightly against the lower edge of the opening.
See Illustration .
. Secure the Bottom Duct Assembly with the two (13 / 16 ") screws A. See Illustration .
CABINET INSTALLATION
1. Place the oven adjacent to the wall or cabinet opening.
Plug the power cord into the electrical outlet.
. Carefully guide the assembled oven into the prepared opening. Slide the oven on the Bottom Duct Assembly.
See Illustration 3. Avoid pinching the cord between the oven and the wall. Adjust the position of the oven so that the feet of the oven are fitted into the recesses of the Bottom Duct Assembly. See Illustration 4.
Illustration 4
FOOT
BOTTOM DUCT
ASSEMBLY
DUCT RECESS
FRAME INSTALLATION
Position the BACK FRAME to align with the predrilled holes that were drilled with the mounting template. Check that it is level and then secure with four SCREWS B. See
Illustration 5.
Place the FRONT FRAME, with tabs on top, onto the
BACK FRAME. Secure the FRONT FRAME to the BACK
FRAME by firmly pushing the front frame onto the back frame engaging the four (4) snap attachments. See illustration 6.
Illustration 5 Illustration 6
SNAP ATTACHMENT
TABS
SCREW B
SCREW B
SCREW B
SCREW B
OVER OVEN INSTALLATION
See illustration 7.
Illustration 7
2" (5.1 cm) For 27" W and 30" W lower oven
3
BASIC SPECIFICATIONS
Microwave Oven
Overall Width 24”
DMOS200
(60.9 cm)
Overall Height from Bottom 13-3/8” (33.9 cm)
Overall Depth from Rear
Oven Interior
19-1/4”
Width
Height
Depth
Overall
(48.9 cm)
17-3/8”
10-1/2”
18-5/8”
2.0 cu. ft.
(44.1 cm)
(26.6 cm)
(47.3 cm)
Cutout Width N/A
Cutout Height
Cutout Depth
Electrical Requirements
Max. Amp Usage
Approx. Shipping Wt.
N/A
N/A
120VAC/60 Hz
1.5 KW 13 amps
46 lbs.
(20.9 kg)
Built-In Trim Kits
DMTK271 DMTK301
26-1/2” (67.3 cm) 29-1/2” (74.9 cm)
18-1/4” (46.3 cm) 18-1/4” (46.3 cm)
N/A
N/A
Min.
Max.
Min.
Max.
Min.
14 lbs.
24-3/8”
24-11/16"
16-3/4”
17"
20”
(61.9 cm)
(62.7 cm)
(42.5 cm)
(43.2 cm)
(50.3 cm)
N/A
N/A
(6.5 kg) 15 lbs.
(6.9 kg)
Viking Range Corporation
111 Front Street • Greenwood, Mississippi (MS) 38930 USA • (662) 455-1200
Specifications subject to change without notice.
For more product information, call 1-888-VIKING1 (845-4641), or visit our web site at http://www.vikingrange.com
F20195B (PS0506VR)
TINSEB466MRR0
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project