Sim2 CRYSTAL CUBE User Manual
إعلان
إعلان
SIM2 Multimedia
CRYSTALCUBE
User G uide
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.
© Copyright 2013
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.
Trademark Recognition
HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
All other product names used in this manual are the properties of their respective owners and are acknowledged.
Ver.: 1
—
i
—
Important Safety Information
Important:
It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector.
Keep this manual for future reference.
Symbols Used
Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
The following styles are used in this manual to alert you to important information.
Note:
Provides additional information on the topic at hand.
Important:
Provides additional information that should not be overlooked.
Caution:
Alerts you to situations that may damage the unit.
Warning:
Alerts you to situations that may damage the unit, create a hazardous environment, or cause personal injury.
Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this example:
“Push the
Menu
button on the remote control to open the
Main
menu.”
General Safety Information
Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in the unit. For servicing, contact qualified service personnel.
Follow all warnings and cautions in this manual and on the unit case.
The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the lens when the lamp is on.
Do not place the unit on an unstable surface, cart, or stand.
Avoid using the system near water, in direct sunlight, or near a heating device.
Do not place heavy objects such as books or bags on the unit.
Important:
Product packaging has been designed for the safety of the product itself.
We suggest to keep it in case of any furthers moving.
—
ii
—
Projector Installation Notice
Place the projector in a horizontal position
The tilt angle of the projector should not exceed 15 degrees,
nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically, and may lead to other
unpredictable damages
.
Ensure that the intake vents do not recycle hot air from the exhaust vent.
When operating the projector in an enclosed space, ensure that the surrounding air temperature within the enclosure does not exceed operation temperature while the projector is running, and the air intake and exhaust vents are unobstructed.
All enclosures should pass a certified thermal evaluation to ensure that the projector does not recycle exhaust air, as this may cause the device to shutdown even if the enclosure temperature is with the acceptable operation temperature range.
–
iii
–
Verify Installation Location
To supply power, the 3-blade (with earthing lead) socket should be used to ensure proper grounding and equalized ground potential for all of the equipment in the Projector System.
The power code provided with the Projector should be used. In case of any missing item, other qualified 3-blade (with earthing lead) power cord can be used as substitution; however, do not use
2-blade power cord.
Verify if the voltage is stable, grounded properly and there is no electricity leakage.
Measure total power consumption which should not higher the safety capacity and avoid safety issue and short circuit.
Turn on Altitude Mode when located in high altitude areas
The projector can only be installed upright or inverted.
When installation the bracket, make sure the weight limit is not exceed and firmly secured.
Avoid installing near air conditioner duct or subwoofer.
Avoid installing at high temperature, insufficient cooling and heavy dust locations.
Keep your product away from fluorescent lamps to avoid malfunction caused by IR interference
The VGA IN connector should be connected to the VGA IN port. Note that it should be inserted tightly, with the screws on both sides securely fastened to ensure proper connection of the signal wire for achieving optimal display effect.
The power cord and signal cable should be connected before power on the projector. During the projector starting and operating process, DO NOT insert or remove the signal cable or the power cord to avoid damaging the projector.
Cooling notes
Air outlet
Make sure the air outlet is 50cm clear of any obstruction to ensure proper cooling.
Air outlet location should not be in front of the lens of other projector to avoid causing illusions.
Keep the outlet at least 100cm away from the inlets of other projectors
The projector generates a massive amount of heat during use. The internal fan dissipates the heat of the projector when shutting down, and such process may continue for a certain period. After the project enters STANDBY MODE status, press the AC power button to turn off the projector and remove the power cord. DO NOT remove the power cord during the shutdown process, as it may cause damage to the projector. In the meantime, the delayed heat radiating will also affect the service life of the projector. The shutdown process may vary depending on the model used.
Whatever the case may be, be sure to disconnect the power cord till after the projector enters the
STANDBY status.
Air inlet
Make sure there is no object blocking air input within 30 cm.
Keep the inlet away from other heat sources
Avoided heavy dust area
—
iv
—
Power Safety
Only use the supplied power cord.
Do not place anything on the power cord. Place the power cord where it will not be in the way of foot traffic.
Remove the batteries from the remote control when storing or not in use for a prolonged period.
Replacing the Lamp
Replacing the lamp can be hazardous if done incorrectly. See
for clear and safe instructions for this procedure. Before replacing the lamp:
Unplug the power cord.
Allow the lamp to cool for about one hour.
Caution:
In rare cases the lamp bulb may burn out during normal operation and cause glass dust or shards to be discharged outward from the rear exhaust vent.
Do not inhale or do not touch glass dust or shards. Doing so could result in injury.
Always keep your face away from the exhaust vent so that you do not suffer from the gas and broken shards of the lamp.
Cleaning the Projector
Unplug the power cord before cleaning. See
Allow the lamp to cool for about one hour.
Regulatory Warnings
Before installing and using the projector, read the regulatory notices in the
on
Important Recycle Instructions:
Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal
Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG
. For lamp specific disposal information check WWW.LAMPRECYCLE.ORG
.
Symbol Explanations
DISPOSAL: Do not use household or municipal waste collection services for disposal of electrical and electronic equipment. EU countries require the use of separate recycling collection services.
–
v
–
Main Features
Compatible with all major video standards including NTSC, PAL, and SECAM.
A high brightness rating allows for presentations in daylight or in lit rooms.
Supports resolutions up to UXGA at 16.7 million colors to deliver crisp, clear images.
Flexible setup allows for front, rear projections.
Line-of-vision projections remain square, with advanced keystone correction for angled projections.
Input source automatically detected.
About this Manual
This manual is intended for end users and describes how to install and operate the DLP projector.
Wherever possible, relevant information
—such as an illustration and its description—has been kept on one page. This printer-friendly format is both for your convenience and to help save paper, thereby protecting the environment. It is suggested that you only print sections that are relevant to your needs.
—
vi
—
Table of Contents
ON-SCREEN DISPLAY (OSD) MENU SETTINGS
–
vii
–
—
viii
—
G
ETTING
S
TARTED
Packing Checklist
Carefully unpack the projector and check that the following items are included: nr.1 CRYSTALCUBE PROJECTOR nr.2 REMOTE CONTROL with BATTERIES (White & Black) nr.2 HDMI ADAPTER nr.1 POWER CORD nr.5 ANGULAR BRACKETS ( 4 pcs for ceiling mounting, 1 pc for spare part ) nr.1 TILT-ADJUSTER H.15 mm nr.1 QUICK START GUIDE (QSG)
Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It is recommend that you keep the original packing material should you ever need to return the equipment for warranty service.
OPTIONAL ACCESSORIES:
- Universal Bracket (
＊
)
- Extension Tube for Bracket (
＊
)
- Boxset VISUS 3D RF Glasses and Emitter (4 pcs) (
＊
)
- Anamorphic Lens with motorized sled
(
＊
) Included in the CRYSTALCUBESE version
Caution:
Avoid using the projector in dusty environments.
Note:
If you need low profiles cables connectors that fit within the compartment on the back of the projector, refer to your local dealer or directly to SIM2 distributor
–
1
–
Views of Projector Parts
Front-right View
I
TEM
L
ABEL
1.
IR receiver
2.
Lens
3.
Focus ring
4.
Zoom ring
D
ESCRIPTION
Receive IR signal from remote control
Projection Lens
Focuses the projected image
Enlarges the projected image
S
EE PAGE
Important:
Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp cool. Do not obstruct any of the ventilation openings.
—
2
—
Rear view
I
TEM
4.
5.
L
ABEL
1.
AC IN
2.
3D SYNC
3.
HDMI 1
HDMI 2
(USB)
6.
VGA IN
7.
RS-232C
8.
COMPONENT
9.
USB POWER
10.
VIDEO IN
11.
S-VIDEO
12.
AUDIO OUT
13.
DC 12V TRIGGER
D
ESCRIPTION
Connect the POWER cable
Connect the SIM2 3D glasses IR transmitter
Connect the HDMI cable from a HDMI device
Connect the HDMI cable from a HDMI device
Connect the USB cable from a computer
S
EE PAGE
Connect the RGB cable from a computer
Connect RS-232 serial port cable for remote control
Connect the Component cable from a component device
For USB charge support DC 5V
Connect the COMPOSITE cable from a video device
Connect the S-VIDEO cable from a video device
Connect an AUDIO cable to audio amplifier
When connected to the screen through a commercially available cable, the screen deploys automatically on start up of the projector. The screen retracts when the projector is powered off (see notes below).
Note:
do not use a 3.5mm mono type cable; use a 3.5mm 3 pin type stereo cable
–
3
–
Note:
To use this feature, you must plug in the connector before turn on/off the projector.
Screen controllers are supplied and supported by screen manufacturers.
Do not use this jack for anything other than intended use.
Note:
If your video equipment has both S-VIDEO and RCA jacks (composite video) connect to the
S-VIDEO connector. S-VIDEO provides a better quality signal.
Warning:
As a safety precaution, disconnect all power to the projector and connecting devices before making connections.
—
4
—
Bottom view
I
TEM
1.
L
ABEL
Tilt adjustor
Ceiling support holes
D
ESCRIPTION
S
EE PAGE
Contact your dealer for information on mounting the projector on a ceiling
Rotate adjuster lever to adjust angle position.
Note:
When installing, ensure that you use only UL Listed ceiling mounts.
For ceiling installations, use approved mounting hardware and M6 screws.
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount load capacity must exceed the weight of the installed equipment, and as an additional precaution be capable of withstanding three times the weight of the equipment (not less than 12 kg) over a period of 60 seconds.
–
5
–
Remote Control Parts
Important:
1.
Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation.
2.
Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens.
—
6
—
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
14.
15.
16.
17.
18.
I
TEM
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
L
ABEL
Power OFF
HDMI 2
PC
VIDEO
Up cursor /
Keystone+
ENTER
Right cursor
Downp cursor /
Keystone-
ASPECT RATIO
SOURCE
2D
3D
BRIGHT
SHARP
COLOR
TINT
BLANK
FREEZE
AUTO
LIGHT
VOL -
VOL +
MUTE
CONTRAST
PICTURE MODE
MENU/ EXIT
Left cursor
COMP
HDMI 1
Power ON
IR transmitter
D
ESCRIPTION
Turns the projector off
Displays the HDMI 2 source selection
Displays the PC source selection
Displays the VIDEO source selection
Navigates and changes settings in the OSD
Quick Menu
– For Keystone
Enters and confirms settings in the OSD
Navigates and changes settings in the OSD
Navigates and changes settings in the OSD
Quick Menu
– For Keystone
Displays the ASPECT RATIO selections
Detects the input device
Toggle 3D function
Displays the brightness setting bar
Displays the sharpness setting bar
Displays the color setting bar
S
EE PAGE
Displays the tint setting bar
Makes the screen blank
Freezes/unfreezes the on-screen picture
Auto adjustment for frequency, phase, and position
Turns on or off the remote control backlight for about 10 seconds.
Pressing any other key while the backlight is on keeps the backlight on for a further 10 seconds.
Adjusts volume
Mutes the AUDIO OUT signal
Displays the contrast settings bar
Changes the Display Mode setting
Opens and exits the OSD
Navigates and changes settings in the OSD
Displays the Component source selection
Displays the HDMI 1 source selection
Turns the projector on
Transmits signals to projector
–
7
–
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and
15 degrees above or below the projector level. If the projector does not respond to the remote control, move a little closer.
—
8
—
Inserting the Remote Control Batteries
1.
Remove the battery compartment cover by sliding the cover in the direction of the arrow.
2.
Insert the batteries paying attention to the positive pole.
3.
Reinsert the compartment cover by sliding the cover in the direction of the arrow.
Caution:
1.
Only use AA batteries (Alkaline batteries are recommended).
2.
Dispose of used batteries according to local ordinance regulations.
3.
Remove the batteries when not using the projector for prolonged periods.
–
9
–
Starting and Shutting down the Projector
1.
Connect the power cord to the projector. Connect the other end to a wall outlet.
The
POWER
LED on the projector light.
2.
Turn on the connected devices.
3.
Ensure the POWER LED is not flashing. Then press the
POWER
button to turn on the projector.
The projector splash screen displays and connected devices are detected.
security lock is enabled.
S
ETUP AND
O
PERATION
4.
If more than one input device is connected, press the
SOURCE
button and use ▲▼ to scroll among devices.
(Component is supported through the RGB to COMPONENT
ADAPTER.)
VGA: Analog RGB
Component Video: Traditional component video
Composite Video: Traditional composite video
S-Video: Super video (Y/C separated)
HDMI 1 / HDMI 2: High-Definition Multimedia
Interface
—
10
—
5.
When the “Power Off? /Press
Power
again” message appears, press the
POWER
button. The projector turns off.
Caution:
Do not unplug the power cord until the POWER LED stops flashing
–indicating the projector has cooled down.
–
11
–
Setting an Access Password (Security Lock)
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector.
When enabled, the password must be entered after you power on the projector. (See
on page 19 for help on using OSD menus.)
Important:
Keep the password in a safe place. Without the password, you will not be able to use the projector.
If you lose the password, contact your reseller for information on clearing the password.
1.
Press the
MENU
button to open the
OSD menu.
2.
Press the cursor ◄► button to move to the
Settings 1
menu, press the cursor ▲▼ button to select
Advanced
1
.
3.
Press (Enter) /
► to enter the
Advanced 1
sub menu. Press the cursor ▲▼ button to select
Security
Lock
.
4.
Press the cursor ◄► button to enter and enable or disable security lock function.
A password dialog box automatically appears.
—
12
—
5.
You can use the cursor buttons
▲▼◄► on IR remote control for password entry. You can use any combination including the same arrow five times, but not less than five.
Press the cursor buttons in any order to set the password. Push the
MENU
button to exit the dialog box.
6.
The password confirm menu appears when user presses the power-on key in case the
Security Lock
is enabled.
Enter the password in the order you set it at step 5. In case you forget the password, please contact the service center.
The service center will validate the owner and help reset the password.
–
13
–
Ceiling Mounting Operation
The CRYSTALCUBE projector has been designed in compliance with world wide safety standards with it's glass cabinet.
Nevertheless, even if the best materials and adhesives available in the market, in order to guarantee a safe application on the long long run, exclusively for the ceiling mounting applications, it's necessary to fit properly the four angular brackets to the corresponding cabinet edges in order to assure glass cabinet safety and to avoid any possible glass part falling.
To do this please observe the following instructions:
1.
Fix on the bottom of the projector the back plate of the ceiling mounting bracket.
2.
Fasten the mounting bracket to the ceiling, accordingly to its producer instructions.
3.
Mount the projector on the ceiling bracket.
4.
Open the rear cable compartment and connect all the necessary cables, paying attention all of them are placed inside of the cable compartment clamp bar.
5.
Switch on the projector and proceed with the alignment procedure.
6.
Lock all the ceiling bracket screws
—
14
—
7.
Insert the angular brackets to the corresponding cabinet edges paying attention to insert them with the locking tab oriented to the bottom of the projector. These angular brackets are in the supplied projector kit in its nylon bag.
(SIM2 supply five angular brackets, four pieces to use for the ceiling mounting and one for spare part)
8.
If you need to remove the angular brackets, unfasten the locking tab.
–
15
–
Adjusting the Projector Level
Take note of the following when setting up the projector:
The projector table or stand should be level and sturdy.
Position the projector so that it is perpendicular to the screen.
Ensure the cables are in a safe location.
To adjust the angle of the picture, turn the tilt-adjuster clockwise or anticlockwise until the desired angle has been achieved.
In case of projection with reduced projection angle (angle between the base and the screen center) use the special tilt-adjuster included in the accessory kit (15 mm long) in place of the frontal one (30 mm long).
—
16
—
Adjusting the Zoom, Focus and Keystone
1.
Use the
Image-zoom
control (on the projector only) to resize the projected image and screen size .
2.
Use the
Image-focus
control (on the projector only) to sharpen the projected image .
3.
Use the RC via OSD
(keystone feature) to correct image-trapezoid
(wider top or bottom) effect.
4.
The keystone control appears on the display.
Adjusting the Volume
1.
Press the
Volume +/-
buttons on the remote control.
The volume control appears on the display.
2.
Press the
MUTE
button to turn off the volume.
(This feature is available only on the remote).
–
17
–
O
N
-S
CREEN
D
ISPLAY
(OSD) M
ENU
S
ETTINGS
OSD Menu Controls
The projector has an OSD that lets you make image adjustments and change various settings.
Navigating the OSD
You can use the remote control cursor buttons to navigate and make changes to the OSD.
1
1
2
3
4
5
1. To enter the OSD, press the
MENU
button.
2. There are three menus.
Press the cursor ◄► button to move through the menus.
3.
Press the cursor ▲▼ button to move up and down in a menu.
4.
Press ◄► to change values for settings.
5. Press
MENU
to close the
OSD or leave a submenu.
Note:
Depending on the video source, not all items in the OSD are available. For example, the
Horizontal/Vertical Position
items in the
Computer
menu can only be modified when connected to a PC. Items that are not available cannot be accessed and are grayed out.
—
18
—
Setting the OSD Language
Set the OSD language to your preference before continuing.
1. Press the
MENU
button. Press the cursor ◄► button to navigate to
Settings 1
. Press the cursor
▲▼ button to move to the
Advanced 1
menu.
2. Press (Enter) /
► to enter the
Advanced 1
sub menu.
Press the cursor ▲▼ button until
Language
is highlighted.
3. Press the cursor button until the language you want is highlighted.
4. Press the
MENU
button four times to close the OSD.
–
19
–
Brightness
Contrast
Computer
Auto Image
Advanced
Color Manager
OSD Menu Overview
Use the following illustration to quickly find a setting or determine the range for a setting.
Main
Menu Sub Menu
Image Display Mode
Horizontal Position
Vertical Position
Frequency
Settings
Presentation, Bright, Game,
Movie, TV, sRGB, Blackboard,
User
0~100
0~100
-5~5 (depend on Autolock)
-5~5 (depend on Autolock)
0~31
Tracking
Brilliant Color
Sharpness
Gamma
Color Temperature
Video AGC
Video Saturation
Video Tint
White Balance
Red
Green
Blue
Cyan
Magenta
Yellow
White
-5~5
0~10
0~31
1.8, 2.0, 2.2, 2.4, B&W, Linear
Warm, Normal, Cold
Off, On
0~100
RGain
0~100
0~200
GGain
BGain
ROffset
GOffset
0~200
0~200
-256~255
-256~255
BOffset -256~255
Hue, Saturation, Gain 0~100
Hue, Saturation, Gain 0~100
Hue, Saturation, Gain 0~100
Hue, Saturation, Gain 0~100
Hue, Saturation, Gain 0~100
Hue, Saturation, Gain 0~100
Red, Green, Blue 0~100
—
20
—
Main
Menu Sub Menu
Settings 1 Source Source
Settings
Projection
Aspect Ratio
Keystone
Digital Zoom
Audio Volume
Mute
SRS
Advanced 1 Language
Security Lock
Blank Screen
Splash Logo
Closed Captioning
3D Setting
Advanced 2 Test Pattern
H Image Shift
V Image Shift
Normal, Real, Ceiling, Real+Ceiling
Fill, 4:3, 16:9, Letter Box, Native, 2.35:1
-40~40
-10~10
0~30
Off, On
Off, On
English, Français, Deutsch, Español, Português,
簡体中文
,
繁體中文
, Italiano, Norsk,
Svenska, Nederlands, Русский, Polski,
Suomi, Ελληνικά,
한국어
, Magyar, Čeština,
ةيبرعلا, Türkçe, Việt,
日本語
,
ไทย
, یسراف,
עברית
Off, On
Blank, Red, Green, Blue, White
Off, On
Off, On
3D Off, DLP-Link, IR
3D Sync Invert Off, On
3D Format Frame Sequential, Top/Bottom, Side-By-
Side, Frame Packing (3D Frame Packing
HDMI source only)
None, Grid, White, Red, Green, Blue,
Black
-50~50
-50~50
–
21
–
Main
Menu Sub Menu
Settings 2 Auto Source
No Signal
Power Off
Auto Power
On
Lamp Mode
Reset All
Status Active Source
Video Information
Lamp Hours(ECO, Normal)
Advanced 1 Menu Position
Translucent Menu
Low Power Mode
Fan Speed
Lamp Hour Reset
Projector ID
Advanced 2 Sleep Timer
Source Filter
Settings
Off, On
0~180
Off, On
ECO , Normal
Center, Down, Up, Left, Right
0%, 25%, 50%, 75%, 100%
Off, On
Normal, High
0-98
0~600
VGA1 Disable, Enable
Component Video Disable, Enable
Composite Video Disable, Enable
S-Video Disable, Enable
HDMI1
HDMI2
Disable, Enable
Disable, Enable
—
22
—
Image Menu
Attention !
All of display mode parameters when changed will be saved to user mode.
Press the
MENU
button to open the
OSD
menu. Press the cursor ◄► button to move to the
Image
Menu
. Press the cursor ▲▼ button to move up and down in the
Image
menu. Press ◄► to enter and change values for settings.
I
TEM
Display Mode
Brightness
Contrast
Computer
Auto Image
Advanced
Color Manager
D
ESCRIPTION
Press the cursor ◄► button to enter and set the Display Mode.
Press the cursor ◄► button to enter and adjust the display brightness.
Press the cursor ◄► button to enter and adjust the display contrast.
Press (Enter)
/ ► to enter the Computer menu. See
Press (Enter)
/ ► to automatically adjustment for phase, tracking, size and position.
Press
(Enter) / ► to enter the Advanced menu. See
on page
Press (Enter)
/ ► to enter the color manager menu. See page
–
23
–
Computer Menu
Press the
MENU
button to open the
OSD
menu. Press ◄► to move to the
Image
menu. Press ▲▼ to move to the
Computer
menu and then press
Enter
or ►. Press ▲▼ to move up and down in the
Computer
menu.
I
TEM
D
ESCRIPTION
Horizontal Position
Press the cursor ◄► button to enter and adjust the display position to left or right.
Vertical Position
Press the cursor ◄► button to enter and adjust the display position to up or down.
Frequency
Tracking
Press the cursor ◄► button to enter and adjust the A/D sampling clock.
Press the cursor ◄► button to enter and adjust the A/D sampling dot.
—
24
—
Advanced Feature
Press the
Menu
button to open the
OSD
menu. Press ◄► to move to the
Image
men u. Press ▼▲ to move to the
Advanced
menu and then press
Enter
or ►. Press ▼▲ to move up and down in the
Advanced
menu.
I
TEM
D
ESCRIPTION
Brilliant Color
Sharpness
Press the cursor ◄► button to enter and adjust the Brilliant Color value.
Press the cursor
◄► button to enter and adjust the display sharpness.
Gamma
Press the cursor ◄► button to enter and adjust the gamma correction of the display.
Color Temperature
Press the cursor ◄► button to enter and adjust the color temperature.
Video AGC
Video Saturation
Video Tint
White Balance
Press the cursor
◄► button to enter and enable or disable the Automatic Gain Control for video source.
Press the cursor
◄► button to enter and adjust the video saturation.
Press the cursor
◄► button to enter and adjust the video tint/hue.
Press
(Enter) / ► button to enter the White Balance sub menu.
–
25
–
White Balance
Press the
ENTER
button to enter the
White Balance
sub menu.
I
TEM
R Gain
G Gain
B Gain
R Offset
G Offset
B Offset
D
ESCRIPTION
Press the ◄► buttons to adjust the Red Gain.
Press the ◄► buttons to adjust the Green Gain.
Press the ◄► buttons to adjust the Blue Gain.
Press the ◄► buttons to adjust the Red Offset.
Press the ◄► buttons to adjust the Green Offset.
Press the ◄► buttons to adjust the Blue Offset.
—
26
—
Color Manager
Press the
Menu
button to open the
OSD
menu. Press ◄► to move to the
Image
menu. Press ▼▲ to move to the
Color Manager
menu and then press
Enter
or ►. Press ▼▲ to move up and down in the
Color Manager
menu.
Red
Green
I
TEM
Blue
Cyan
Magenta
Yellow
White
D
ESCRIPTION
Select to enter the Red Color Manager.
Press the
◄► buttons to adjust the Hue, Saturation, and Gain.
Select to enter the Green Color Manager.
Press the
◄► buttons to adjust the Hue, Saturation, and Gain.
Select to enter the Blue Color Manager.
Press the
◄► buttons to adjust the Hue, Saturation, and Gain.
Select to enter the Cyan Color Manager.
Press the
◄► buttons to adjust the Hue, Saturation, and Gain.
Select to enter the Magenta Color Manager.
Press the
◄► buttons to adjust the Hue, Saturation, and Gain.
Select to enter the Yellow Color Manager.
Press the
◄► buttons to adjust the Hue, Saturation, and Gain.
Select to enter the White Color Manager.
Press the
◄► buttons to adjust the Red, Green, and Blue.
–
27
–
Settings 1 Menu
Press the
MENU
button to open the
OSD
menu. Press the cursor ◄► button to move to the
Settings 1
menu. Press the cursor ▲▼ button to move up and down in the
Settings 1
menu. Press
◄► to enter and change values for settings.
I
TEM
Source
Projection
Aspect Ratio
Keystone
Digital Zoom
Audio
Advanced 1
Advanced 2
D
ESCRIPTION
Press the cursor ◄► button to enter the Source menu.
Press the cursor ◄► button to enter and choose from four projection methods:
Press the cursor ◄► button to enter and adjust the video aspect ratio.
Press the cursor ◄► button to enter and adjust the display keystone.
Press the cursor ◄► button to enter and adjust the Digital Zoom menu.
Press (Enter) /
► to enter the Audio menu. See
Press
(Enter) / ► to enter the Advanced 1 menu. See
Press
(Enter) / ► to enter the Advanced 2 menu. See
on
—
28
—
Audio
Press the
Menu
button to open the
OSD
menu. Press ◄► to move to the
Settings 1
menu. Press
▼▲ to move to the
Audio
menu and then press
Enter
or ►. Press ▼▲ to move up and down in the
Audio
menu.
I
TEM
Volume
Mute
SRS
D
ESCRIPTION
Press the cursor
◄► button to enter and adjust the audio volume.
Press the cursor
◄► button to enter and turn on or off the audio out put.
Press the cursor
◄► button to enter and turn on or off the audio surround.
–
29
–
Advanced 1 Feature
Press the
Menu
button to open the
OSD
menu. Press ◄► to move to the
Settings 1
menu. Press
▲▼ to move to the
Advanced 1
menu and then press
Enter
or ►. Press ▲▼ to move up and down in the
Advanced 1
menu. Press ◄► to enter and change values for setting.
I
TEM
D
ESCRIPTION
Language
Security Lock
Press the cursor ◄► button to enter and select a different localization Menu.
Press the cursor ◄► button to enter and enable or disable security lock function.
Blank Screen
Splash Logo
Press the cursor ◄► button to enter and select different color to blank the screen.
Press the cursor ◄► button to enter and select splash logo on or off.
Closed Captioning Press the cursor
◄► button to enter and enable or disable Closed Captioning
3D Setting
Press (Enter) /
►to enter the 3D menu. See page
Note:
To enjoy the 3D function, first enable the Play Movie in 3D setting found in your DVD device under the
3D Disc Menu.
—
30
—
3D Setting
I
TEM
3D
3D Sync Invert
3D Format
D
ESCRIPTION
Press the cursor ◄► button to enter and select different 3D mode.
Press the cursor ◄► button to enter and enable or disable 3D Sync Invert.
Press the cursor ◄► button to enter and enable or disable different 3D Format.
Note:
1. The 3D OSD menu item is gray if there is no appropriate 3D source. This is the default setting.
2. When the projector is connected to an appropriate 3D source, the 3D OSD menu item is enabled for selection.
3. Use 3D glasses to view a 3D image.
4. You need 3D content from a 3D DVD/BRD or 3D media file.
5. You need to enable the 3D source (some 3D DVD content may have a 3D on-off selection feature).
6. You need IR/RF shutter glasses. With IR/RF 3D shutter glasses, you have to connect the emitter to the 3D SYNC connector on the rear panel.
7. The 3D mode of the OSD needs to match the type of glasses.
8. Power on the glasses. Glasses normally have a power on -off switch.
Each type of glasses has their own configuration instructions. Please follow the configuration instructions that come with your glasses to finish the setup process.
Note:
Since different types of glass (IR/RF 3D) have their own setting instructions, Please follow the guide to finish the setup process.
–
31
–
Advanced 2 Feature
Press the
Menu
button to open the
OSD
menu. Press ◄► to move to the
Settings 1
menu. Press
▲▼ to move to the
Advanced 2
menu and then press
Enter
or ►. Press ▲▼ to move up and down in the
Advanced 2
menu. Press ◄► to enter and change values for setting.
I
TEM
Test Pattern
H Image Shift
V Image Shift
D
ESCRIPTION
Press the cursor ◄► button to enter and select internal test pattern.
Press the cursor ◄► button to enter and select H Image Shift.
Press the cursor ◄► button to enter and select V Image Shift.
—
32
—
Settings 2 Menu
Press the
MENU
button to open the
OSD
menu. Press the cursor ◄► button to move to the
Settings 2
menu. Press the cursor ▲▼ button to move up and down in the
Settings 2
menu.
I
TEM
Auto Source
No Signal Power
Off (min.)
Auto Power On
Lamp Mode
Reset All
Status
Advanced 1
Advanced 2
D
ESCRIPTION
Press the cursor ◄► button to enter and enable or disable automatic source detection.
Press the cursor ◄► button to enter and enable or disable automatic shutdown of lamp when no signal.
Press the cursor ◄► button to enter and enable or disable automatic power On when
AC power is supplied.
Press the cursor ◄► button to enter and select the lamp mode for higher brightness or lower brightness to save lamp life.
Press (Enter) /
► to reset all settings to default values.
Press
(Enter) / ► to enter the Status menu. See page
for more information on
Press
(Enter) / ► to enter the Advanced 1 menu. See
on
Press
(Enter) / ► to enter the Advanced 2 menu. See
on
–
33
–
Status
Press the cursor ▲▼ button to move up and down in the
Settings 2
menu. Select the
Status
menu and press
Enter
or ► to enter.
I
TEM
Active Source
Video Information
Lamp Hours
D
ESCRIPTION
Display the activated source.
Displays resolution/video information for RGB source and color standard for Video source.
Lamp hour used information is displayed. ( ECO. and Normal)
—
34
—
Advanced 1 Feature
Press the
Menu
button to open the
OSD
menu. Press ◄► to move to the
Settings 2
menu. Press
▲▼ to move to the
Advanced 1
menu and then press
Enter
or ►. Press ▲▼ to move up and down in the
Advanced 1
menu. Press ◄► to enter and change values for setting.
I
TEM
D
ESCRIPTION
Menu Position Press the cursor
◄► button to enter and select different OSD location.
Translucent Menu Press the cursor
◄► button to enter and select OSD background translucent level.
Low Power Mode
Fan Speed
Press the cursor
◄► button to enter and turn Low Power Mode on or off.
Press the cursor ◄► button to enter and toggle between Normal and High fan speeds.
Note
: We recommend selecting high speed in high temperatures, high humidity, or high altitude (higher than 1500m/4921ft) areas.
Lamp Hour Reset
Projector ID
After replacing the lamp, this item should be reset. See page 36 for more information on
Press the cursor
◄► button to enter and adjust a two digit projector ID from 00 through 98.
–
35
–
Lamp Hour Reset
on page 41 to reset the lamp hour counter.
—
36
—
Advanced 2 Feature
Press the
Menu
button to open the
OSD
menu. Press ◄► to move to the
Settings 2
menu. Press
▲▼ to move to the
Advanced 2
menu and then press
Enter
or ►. Press ▲▼ to move up and down in the
Advanced 2
menu. Press ◄► to enter and change values for setting.
I
TEM
Source Filter
Sleep Timer (min)
D
ESCRIPTION
Press the cursor ◄► button to enter and set Sleep timer. The projector automatically turns off after the preset period of time.
Press
(Enter) / ► to enter the Source Filter menu. See page
–
37
–
Source Filter
Press the
ENTER
button to enter the
Source Filter
sub menu.
I
TEM
VGA
Component Video
Composite Video
S-Video
HDMI 1
HDMI 2
D
ESCRIPTION
Press the cursor
◄► button to enter and enable or disable the VGA1 source.
Press the cursor
◄► button to enter and enable or disable the Component Video source.
Press the cursor
◄► button to enter and enable or disable the Composite Video source.
Press the cursor
◄► button to enter and enable or disable the S-Video source.
Press the cursor
◄► button to enter and enable or disable the HDMI 1 source.
Press the cursor ◄► button to enter and enable or disable the HDMI 2 source.
—
38
—
M
AINTENANCE AND
S
ECURITY
Replacing the Projection Lamp
The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer.
Important:
a.
The projection lamp used in this product contains a small amount of mercury.
b.
Do not dispose this product with general household waste.
c.
Disposal of this product must be carried out in accordance with the regulations of your local authority.
Warning:
Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp. Failure to do so could result in a severe burn.
Caution:
In rare cases the lamp bulb may burn out during normal operation and cause glass dust or shards to be discharged outward from the rear exhaust vent.
Do not inhale or do not touch glass dust or shards. Doing so could result in injury.
Always keep your face away from the exhaust vent so that you do not suffer from the gas and broken shards of the lamp.
When removing the lamp from a ceiling-mounted projector, make sure that no one is under the projector. Glass fragments could fall if the lamp has been burned out.
IF A LAMP EXPLODES
If a lamp explodes, the gas and broken shards may scatter inside the projector and they may come out of the exhaust vent. The gas contains toxic mercury.
Open windows and doors for ventilation.
If you inhale the gas or the shards of the broken lamp enter your eyes or mouth, consult the doctor immediately.
1.
Disconnect all the cables from the rear panel.
–
39
–
2.
Turn upside down the projector.
Loosen the four screws on the bottom of the projector.
3.
Remove the glass cabinet.
4.
Remove the two screws from the lamp module.
5.
Lift the module handle up.
6.
Pull firmly on the module handle to remove the lamp module and replace the lamp module.
7.
Reverse steps 1 to 6 to install the new lamp module.
While installing, align the lamp module with the connector and ensure it is level to avoid damage.
Note:
The lamp module must sit securely in place and the lamp connector must be connected properly before tightening the screws.
—
40
—
Resetting the Lamp
After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following:
1.
Press the
MENU
button to open the OSD menu.
2.
Press the cursor
◄► button to move to the
Settings 2
menu.
Press the cursor button to move down to
Advanced 1
and press enter.
3.
For password please contact the closest SIM2 Distributor or service centre.
4.
Press the cursor ► or Enter button.
A message screen appears.
5.
Press
▼▲◄► buttons to reset the lamp hour.
6.
Press the
MENU
button to get back to
Settings 2
.
–
41
–
Cleaning the Projector
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.
Warning:
1.
Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so could result in a severe burn.
2.
Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings on the projector.
3.
If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated room for several hours before using.
4.
If a lot of water gets into the projector interior when cleaning, have the projector serviced.
Cleaning the Lens
You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the projector lens.
1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the lens.)
2. Lightly wipe the lens in a circular motion.
Caution:
1.
Do not use abrasive cleaners or solvents.
2.
To prevent discoloration or fading, avoid getting cleaner on the projector case.
Cleaning the Case
Refer to the following to clean the projector case.
1. Wipe off dust with a clean dampened cloth.
2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and then wipe the case.
3. Rinse all detergent from the cloth and wipe the projector again.
—
42
—
T
ROUBLESHOOTING
Common problems and solutions
These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance.
Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check the following before proceeding to the problem-specific solutions.
Use some other electrical device to confirm that the electrical outlet is working.
Ensure the projector is turned on.
Ensure all connections are securely attached.
Ensure the attached device is turned on.
Ensure a connected PC is not in suspending mode.
Ensure a connected notebook computer is configured for an external display.
(This is usually done by pressing an Fn-key combination on the notebook.)
Tips for Troubleshooting
In each problem-specific section, try the steps in the order suggested. This may help you to solve the problem more quickly.
Try to pin point the problem and thus avoid replacing non-defective parts.
For example, if you replace batteries and the problem remains, put the original batteries back and go to the next step.
Keep a record of the steps you take when troubleshooting: The information may be useful when calling for technical support or for passing on to service personnel.
–
43
–
LED Error Messages
E
RROR
System Initial
C
ODE
M
ESSAGES
P
OWER
L
ED
G
REEN
Flashing
L
AMP
L
ED
R
ED
OFF
T
EMP
L
ED
R
ED
OFF
OFF Ready to Power on (Standby)
System Power on
Lamp Lit , System stable
Cooling
Over Temperature
Thermal Break Sensor error
Lamp Fail
Lamp Temperature shut down
Lamp Short circuit in output detected
Lamp End of lamp life detected
Lamp did not ignite
Lamp extinguished during normal operation
Lamp extinguished during run-up phase
Lamp voltage got error
Lamp ballast got error
ON
Flashing
ON
Flashing
ON
4 blinks
5 blinks
5 blinks
5 blinks
5 blinks
5 blinks
5 blinks
5 blinks
5 blinks
5 blinks
OFF
OFF
OFF
OFF
OFF
OFF
ON
1 blinks
2 blinks
3 blinks
4 blinks
5 blinks
6 blinks
7 blinks
8 blinks
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Ballast watt value is out of range
(Lamp Normal & Eco mode)
5 blinks 9 blinks OFF
Lamp ballast Communication error
5 blinks 10 blinks
OFF
Fan-1 error
6 blinks 1 blinks
OFF
Fan-2 error
6 blinks 2 blinks
OFF
Fan-3 error
6 blinks 3 blinks
OFF
Case Open
7 blinks OFF
OFF
DAD1000 error
8 blinks OFF
OFF
Color wheel error
9 blinks OFF
OFF
In the event of an error, please disconnect the AC power cord and wait for one (1) minute before restarting the projector. If the Power or Lamp LEDs are still blinking or any other situation that isn't listed in the chart above
, please contact your service center.
Image Problems
Problem: No image appears on the screen
1.
Verify the settings on your notebook or desktop PC.
2.
Turn off all equipment and power up again in the correct order.
Problem: The image is blurred
1.
Adjust the
Focus
on the projector.
2.
Press the
Auto
button on the remote control.
3.
Ensure the projector-to-screen distance is within the specified range.
4.
Check that the projector lens is clean.
Problem: The image is wider at the top or bottom (trapezoid effect)
1.
Position the projector so it is as perpendicular to the screen as possible.
—
44
—
2.
Use the
Keystone
button on the remote control to correct the problem.
Problem: The image is reversed
Check the
Projection
setting on the
Settings 1
menu of the OSD.
Problem: The image is streaked
1.
Set the
Frequency
and
Tracking
settings on the
Image->Computer
menu of the OSD to the default settings.
2.
To ensure the problem is not caused by a connected PC’s video card, connect to another computer.
Problem: The image is flat with no contrast
Adjust the
Contrast
setting on the
Image
menu of the OSD.
Problem: The color of the projected image does not match the source image.
Adjust the
Color Temperature
and
Gamma
settings on the
Image->Advanced
menu of the
OSD.
Lamp Problems
Problem: There is no light from the projector
1.
Check that the power cable is securely connected.
2.
Ensure the power source is good by testing with another electrical device.
3.
Restart the projector in the correct order and check that the Power LED is on.
4.
If you have replaced the lamp recently, try resetting the lamp connections.
5.
Replace the lamp module.
6.
Put the old lamp back in the projector and have the projector serviced.
Problem: The lamp goes off
1.
Power surges can cause the lamp to turn off. Re-plug power cord. When the Power LED is on, press the power button.
2.
Replace the lamp module.
3.
Put the old lamp back in the projector and have the projector serviced.
Remote Control Problems
Problem: The projector does not respond to the remote control
1.
Direct the remote control towards remote sensor on the projector.
2.
Ensure the path between remote and sensor is not obstructed.
3.
Turn off any fluorescent lights in the room.
4.
Check the battery polarity.
5.
Replace the battery.
6.
Turn off other Infrared-enabled devices in the vicinity.
7.
Have the remote control serviced.
Audio Problems
Problem: There is no sound
1.
Adjust the volume on the remote control.
2.
Adjust the volume of the audio source.
3.
Check the audio cable connection.
4.
Test the source audio output with other speakers.
–
45
–
5.
Have the projector serviced.
Problem: The sound is distorted
1.
Check the audio cable connection.
2.
Test the source audio output with other speakers.
3.
Have the projector serviced.
Having the Projector Serviced
If you are unable to solve the problem, you should have the projector serviced. Pack the projector in the original carton. Include a description of the problem and a checklist of the steps you took when trying to fix the problem: The information may be useful to service personnel. For servicing, return the projector to the place you purchased it.
—
46
—
HDMI Q & A
Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI cable?
Recently, HDMI Licensing, LLC announced that cables would be tested as Standard or High -
Speed cables.
˙Standard (or “category 1”) HDMI cables have been tested to perform at speeds of 75Mhz or up to 2.25Gbps, which is the equivalent of a 720p/1080i signa l.
˙High Speed (or “category 2”) HDMI cables have been tested to perform at speeds of 340Mhz or up to 10.2Gbps, which is the highest bandwidth currently available over an HDMI cable and can successfully handle 1080p signals including those at increased co lor depths and/or increased refresh rates from the Source. High-Speed cables are also able to accommodate higher resolution displays, such as WQXGA cinema monitors (resolution of 2560 x 1600).
Q. How do I run HDMI cables longer than 10 meters?
There are many HDMI Adopters working on HDMI solutions that extend a cable’s effective distance from the typical 10 meter range to much longer lengths. These companies manufacture a variety of solutions that include active cables (active electronics built into cable s that boost and extend the cable’s signal), repeaters, amplifiers as well as CAT5/6 and fiber solutions.
Q. How can I tell if a cable is an HDMI certified cable?
All HDMI products are required to be certified by the manufacturer as part of the HDMI
Compliance Test Specification. However, there may be instances where cables bearing the
HDMI logo are available but have not been properly tested. HDMI Licensing, LLC actively investigates these instances to ensure that the HDMI trademark is properly used in th e market. We recommend that consumers buy their cables from a reputable source and a company that is trusted.
For more detail information check http://www.hdmi.org/learningcenter/faq.aspx#49
–
47
–
S
PECIFICATIONS
Specifications
Model
Display type
Resolution
Projection distance
Projection screen size
Projection lens
Zoom ratio
Vertical keystone correction
Projection methods
Data compatibility
SDTV/EDTV/ HDTV
Video compatibility
H-Sync
V-Sync
Safety certification
Operation temperature
Dimensions
AC Input
Power consumption
Lamp
CRYSTALCUBE
TI DMD 1080p
1080p 1920x1080
1.2 ~ 10 m
25.9" ~ 324.97"
Manual Focus/Manual Zoom
1.5x
+/- 40 Degree
Input Terminals
Output Terminals
Control Terminals
Front, Rear, Desktop/Ceiling (Rear, Front)
VGA, SVGA, XGA, WXGA, SXGA, SXGA+, UXGA, WUXGA, Mac
480i, 480p, 576i, 576p, 720p, 1080i, 1080p
NTSC, PAL, SECAM
2D: 15, 30~91.4KHz / 3D: 101.6KHz
24~30Hz, 47~120Hz
FCC-B, cUL, UL, CE, CCC
5° ~ 35°C
316 mm (W) x 316 mm (D) x 180 mm (H)
AC Universal 100-240V
240W, <0.5W(Stand By)
190W (Boost) / 160W (Std)
VGA x 1
Component (YPbPr RCAx3) x 1
Composite x 1
S-Video x 1
HDMI x 2
PC Audio jack(3.5mm) x 1
RS-232C
3D sync
Screen trigger: DC Jack x 1 (DC12V 200mA output function)
USB (Type mini B) - service only
USB (type A) support DC 5V
Note:
For questions regarding product specifications, please contact your local distributor.
—
48
—
Projection Distance vs. Projection Size
I
MAGE
D
IAGONAL
（
INCH
）
I
MAGE
W
IDTH
(
INCH
)
84
90
96
100
60
70
72
80
120
135
150
200
Projection Distance and Size Table
52.3
61.0
62.8
69.7
73.2
78.4
83.7
87.2
104.6
117.7
130.7
174.3
29.4
34.3
35.3
39.2
41.2
44.1
47.1
49.0
58.8
66.2
73.5
98.1
CRYSTALCUBE
I
MAGE
H
IGHT
(
INCH
)
P
ROJECTION
D
ISTANCE
（
M
）
F
ROM
1.85
2.15
2.22
2.46
2.58
2.77
2.95
3.08
3.69
4.15
4.62
6.15
P
ROJECTION
D
ISTANCE
（
M
）
TO
2.78
3.24
3.33
3.70
3.89
4.16
4.44
4.63
5.55
6.25
6.94
9.25
O
FFSET
-A
( M )
0.11
0.13
0.13
0.15
0.16
0.17
0.18
0.19
0.22
0.25
0.28
0.37
–
49
–
Timing Mode Table
S
IGNAL
R
ESOLUTION
H-S
YNC
( KH
Z
)
V-S
YNC
( H
Z
)
NTSC
PAL/SECAM
VESA
1024 x 576
1024 x 600
1024 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1280 x 720
1280 x 720
1280 x 768
1280 x 768
1280 x 800
1280 x 800
1280 x 800
1280 x 800
1280 x 1024
1280 x 1024
1280 x 1024
－
－
640 x 400
720 x 400
720 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
45
90
47.4
47.8
49.7
62.8
60
68.7
97.6
99
67.5
35.8
37.3
41.5
48.4
56.5
71.6
101.6
64
80
91.1
37.5
43.3
35.2
37.9
46.9
48.1
53.7
76.3
15.734
15.625
37.9
31.5
37.9
31.5
37.9
60
120
60
59.9
59.8
74.9
75
85
120
120
75
60
60
65
60
70.1
84.9
119.9
60
75
85
75
85
56.3
60.3
75
72.2
85.1
120
60
50
85.08
70.1
85.04
60
72.8
C
OMPOSITE
S_V
IDEO
C
OMPONENT
RGB
(A
NALOG
)
HDMI
(D
IGITAL
)
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
－
－
○
○
○
○
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
○
○
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
－
－
○
○
○
○
—
50
—
S
IGNAL
R
ESOLUTION
H-S
YNC
( KH
Z
)
V-S
YNC
( H
Z
)
C
OMPOSITE
S_V
IDEO
C
OMPONENT
RGB
(A
NALOG
)
HDMI
(D
IGITAL
)
Apple
Macintosh
SDTV
EDTV
HDTV
1280 x 960
1280 x 960
1360 x 768
1400 x 1050
1440 x 900
1440 x 900
1440 x 900
1600 x1200
1680 x 1050
1680 x 1050
1920 x 1200
1920 x 1080
640 x 480
832 x 624
1024 x 768
1152 x 870
480i
576i
576p
480p
720p
720p
1080i
1080i
1080p
60
85.9
47.7
65.3
55.5
55.9
70.6
75
64.7
65.3
74
67.5
35
49.7
60.2
68.7
15.734
15.625
31.3
31.5
37.5
45
33.8
28.1
27
60
85
60
60
59.9
59.9
75
60
59.9
60
60
60
66.7
74.5
74.9
75.1
60
50
50
60
50
60
60
50
24
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
○
○
○
○
○
○
○
○
○
○
○
－
－
－
－
－
－
－
－
－
－
－
－
－
－
1080p
1080p
28
33.7
25
30
1080p
1080p
56.3
67.5
50
60
－
－
○
○
－
－
O
：
Frequency supported
—
：
Frequency not supported
The native resolution of the panel is 1920x1080
Resolution others than native resolution may be display with uneven size of text or line
The color of mean Displayable only. (4:3 only)
HDTV timing main check tool is DVD player, VG828 is secondary
－
－
－
○
○
－
－
－
－
－
－
－
－
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
–
51
–
Projector Dimensions
—
52
—
R
EGULATORY
C
OMPLIANCE
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense.
Changes or modifications not expressly approved by the parties responsible for compliance could void the user’s authority to operate the equipment.
Canada
This class B digital apparatus complies with Canadian ICES-003.
Safety Certifications
FCC-B, cUL, UL, CE, CCC
–
53
–
تنزيل
تم تحديث الرابط العام
رابط عام للمستند
إعلان