AMS AS1712 Power Management Datasheet
Advertisement
Advertisement
austriamicrosystems AG is now ams AG
The technical content of this austriamicrosystems datasheet is still valid.
Contact information:
Headquarters:
ams AG
Tobelbaderstrasse 30
8141 Unterpremstaetten, Austria
Tel: +43 (0) 3136 500 0 e-Mail: [email protected]
Please visit our website at
www.ams.com
D a ta s h e e t
AS1710/AS1712
High-Output-Drive, 10MHz, 10V/µs, Rail-to-Rail I/O Op Amps with Shutdown
1 General Description 2 Key Features
The AS1710/AS1712 are low-offset, high-output CMOS op-amps that deliver 200mA of peak output current from a single supply (2.7V to 5.5V).
Constant Output Drive Capability: 50mA
Rail-to-Rail Input and Output
The devices are available as the standard products shown in
Ordering Information on page 18 .
Supply Current: 1.6mA
These devices were specifically designed to drive typical headset levels (32
), as well as bias RF power amplifiers for wireless handset applications.
Table 1. Standard Products
Model
AS1710A Single Op Amp with Shutdown
AS1710B
Description
Single Op Amp
AS1712A Quad Op Amp with Shutdown
Package
SC70-6
SC70-5
TQFN-16
(3x3mm)
Single-Supply Operation: 2.7V to 5.5V
Gain-Bandwidth Product: 10MHz
High Slew Rate: 10V/µs
Voltage Gain: 100dB (R
LOAD
= 100k
)
Power-Supply Rejection Ratio: -85dB
No Phase Reversal for Overdriven Inputs
Unity-Gain Stable for Capacitive Loads: Up to 100pF
Shutdown Mode (AS1710A) Current: 1nA typ
Package Types:
- SC70-5
still valid
These rail-to-rail I/O, wide-bandwidth amplifiers exhibit a high slew rate of 10V/µs and a gain-bandwidth product of 10MHz.
- TQFN-16 (3x3mm)
The integrated shutdown feature (not included in B versions) drives the output low.
These devices operate over the entire industrial temperature range
(-40ºC to +85ºC).
ams
Figure 1. AS1710 - Typical Application
3 Applications
The devices are ideal for portable/battery-powered audio applications, portable headphone speaker drivers (32
), hands-free mobile phone kits, TFT panels, sound ports/cards, set-top boxes, biasing controls, DAC converter buffers, transformer/line drivers,
content
R
F
Audio In
Left
C
IN
R
IN
–
+
AS1710
+
C
OUT
Headphone Jack to 32
Stereo
Headset
V
BIAS
+
–
AS1710
+
C
OUT
Audio In
Right
C
IN
IN
R
F
1 - 19 www.austriamicrosystems.com/Audio/OpAmps/AS1710_12 Revision 1.9
AS1710/AS1712
Datasheet - P i n A s s i g n m e n t s
4 Pin Assignments
Figure 2. Pin Assignments (Top View)
IN+ 1 6 VDD IN+ 1 5 VDD
VSS 2
IN3
AS1710-A
SC70-6
IN1+ 1
VSS 2
IN3
AS1710-B
SC70-5
5 SHDNN
4 OUT
VDD 2
12 IN4+
4 OUT
still valid
AS1712-A
TQFN-16 (3x3mm)
IN2+ 3
9 IN3IN24
ams
Exposed Pad
content
4.1 Pin Descriptions
Table 2. Pin Descriptions
Pin Number Pin Name Description
IN+
Non-inverting Input
IN-
Inverting Input
VDD
Positive Supply Input
See
VSS
SHDNN
OUT
Exposed Pad
Negative Supply Input. This pin must be connected to ground in single-supply applications.
Active Low Shutdown Control
Exposed Pad. This pin also functions as a heat sink. Solder it to a large pad or to the circuit-board ground plane to maximize power dissipation.
www.austriamicrosystems.com/Audio/OpAmps/AS1710_12 Revision 1.9
2 - 19
AS1710/AS1712
Datasheet - A b s o l u t e M a x i m u m R a t i n g s
5 Absolute Maximum Ratings
maximum rating conditions for extended periods may affect device reliability.
Table 3. Absolute Maximum Ratings
Min Max Units Comments Parameter
Electrical Parameters
Supply Voltage (V
DD
to V
SS
) V
V
SS
- 0.3
+7
V
DD
+ 0.3
Supply Voltage (All Other Pins)
Output Short-Circuit Duration to
V
DD
or V
SS
Thermal Information
Continuous Power Dissipation
SC70-5
SC70-6
1
V s mW Derate at 31mW/ºC above 70ºC
valid
247
245
TQFN-16
(3x3mm)
Thermal Resistance
JA
Temperature Ranges and Storage Conditions
Storage Temperature Range
Junction Temperature
Package Body Temperature
Humidity non-condensing
Moisture Sensitive Level
-65
ams
33
+150
+150
+260
85
ºC/W
AG
ºC
%
The reflow peak soldering temperature (body temperature) specified is in accordance with IPC/
JEDEC J-STD-020 “Moisture/Reflow Sensitivity
Classification for Non-Hermetic Solid State Surface
Mount Devices”.
The lead finish for Pb-free leaded packages is matte tin
(100% Sn).
content
Technical
www.austriamicrosystems.com/Audio/OpAmps/AS1710_12 Revision 1.9
3 - 19
AS1710/AS1712
Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s
6 Electrical Characteristics
All limits are guaranteed. The parameters with Min and Max values are guaranteed by production tests or SQC (Statistical Quality Control) methods.
6.1 DC Electrical Characteristics
V
DD
= 2.7V, V
SS
= 0V, V
CM
= V
DD
/2, V
OUT
= V
DD
/2, R
LOAD
= Infinite, V
SHDNN
= V
DD
, Typical values at T
AMB
= 25ºC.
Table 4. DC Electrical Characteristics
Symbol
T
AMB
V
DD
V
OFFSET
I
BIAS
I
OFFSET
R
IN
V
CM
CMRR
PSRR
R
OUT
V
OUT-SHDNN
A
VOL
V
OUT
Parameter
Operating Temperature Range
Condition Min
-40
Typ Max
+85
Unit
ºC
Supply Voltage Range
Input Offset Voltage
Input Bias Current
Input Offset Current
Input Resistance
Inferred from Power Supply
Rejection Ratio Test
V
CM
= V
SS
to V
DD
V
CM
= V
SS
to V
DD
Common Mode Input
Voltage Range
Common Mode
Rejection Ratio
Power Supply Rejection Ratio
Shutdown Output Impedance
Shutdown Output Voltage
Inferred from Common Mode
Rejection Ratio
1
V
V
V
SS
DD
SHDNN
< V
AG
V
SHDNN
= 0V, R
LOAD
= 2k
to V
DD
(A-Versions)
Large Signal Voltage Gain
Output Voltage Swing
Output Voltage
V
SS
+ 0.20V < V
OUT
<
ams
- 0.20V
OH
or
V
OL
- V
SS
V
DD
- V
OH
or
V
OL
- V
SS
R
LOAD
= 100k
I
R
LOAD
= 2k
R
LOAD
= 200
R
LOAD
= 32
V
DD
= 2.7V
I
LOAD
= 30mA,
V
DD
= 5V
85
79
69
2.7
-3 0.6
50
1
50
1
V
-70
1000
1
SS
-45
still
DD
-85
130
1
5.5 V
+3
valid
pA
M
V dB dB
170
100
92
80
350
70
9
55
100
300
650
120
20
100
180 mV dB mV mV
I
OUT
I
DD
Output Source/Sink Current
Quiescent Supply Current per
Op Amp Output
V
DD
= 2.7V,
V- = V
CM
, V+ = V
CM
±100mV
V
DD
= 5.0V,
V- = V
CM
, V+ = V
CM
±100mV
V
DD
= 2.7V, V
CM
= V
DD
/2
V
DD
= 5.0V, V
CM
= V
DD
/2
I
DD-SHDNN
V
SHDNN
= 0V V
DD
= 2.7V
Shutdown Supply Current per
Op Amp (A-Versions)
Technical
1. Guaranteed by design.
(A-Versions)
Shutdown Mode
Normal Operation
V
SS
< V
SHDNN
< V
DD
(A-Versions)
100
200
1.6
2.3
1
V
SS
+
0.3
V
DD
-
0.3
50
1
3.2
4.6
2000
1 mA mA nA
V pA
4 - 19 www.austriamicrosystems.com/Audio/OpAmps/AS1710_12 Revision 1.9
AS1710/AS1712
Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s
6.2 AC Electrical Characteristics
V
DD
= 2.7V, V
SS
= 0V, V
CM
= V
DD
/2, V
OUT
= V
DD
/2, R
LOAD
= Infinite, V
SHDNN
= V
DD
, Typical values at T
AMB
= 25ºC.
Table 5. AC Electrical Characteristics
Symbol Parameter Min Typ Conditions
V
CM
= V
DD
V
OUT
= 2VP-P, V
DD
= 5V 2.5
Max Units
MHz t
GM
THD+N
Gain Margin
1
Total Harmonic Distortion
Plus Noise
C
IN
Input f = 10kHz, V
OUT
= 2V
P-P
, A
VCL
= 1V/V en
Voltage-Noise Density
1 f = 1kHz f = 10kHz t
SHDN
ENABLE t
ON
Capacitive-Load Stability
Shutdown Time
(AS1710A)
Enable Time from Shutdown
(AS1710A)
Power-Up Time
1. Guaranteed by design.
A
VCL
= 1V/V, no sustained oscillations
AG
0.05
70 deg
15 dB
%
6 pF
valid
15
10
still
7 nV/
Hz pF
µs
20 ns
Technical
www.austriamicrosystems.com/Audio/OpAmps/AS1710_12 Revision 1.9
5 - 19
AS1710/AS1712
Datasheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s
7 Typical Operating Characteristics
V
DD
= 2.7V; V
SS
= 0V, V
CM
= V
DD
/2, V
OUT
= V
DD
/2, R
LOAD
=
, V
SHDNN
= V
DD
T
AMB
= +25ºC (unless otherwise specified).
Figure 3. Gain and Phase vs. Frequency Figure 4. Gain and Phase vs. Frequency, C
LOAD
= 100pF
120 320 120 320
Gain Gain
100 280 100 280
80
60
Phase
40
20
0
-20
-40
0.001
240
200
160
120
80
40
0.1
10
0
1000 100000
Frequency (kHz)
Figure 5. PSRR vs. Frequency
100
PSRR pos
90
80
PSRR neg
70
60
50
40
30
20
10
0
0,001 0,1 10
Frequency (kHz)
ams
100
90
80
70
60
50
40
30
20
10
1000
0.001
80
60
Phase
40
20
0
-20
-40
0.001
CMRR
0.1
10
Frequency (kHz)
1000
240
200
160
120
80
40
0
0.1
10 1000 100000
Frequency (kHz)
still valid
Technical
www.austriamicrosystems.com/Audio/OpAmps/AS1710_12 Revision 1.9
6 - 19
AS1710/AS1712
Datasheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s
Figure 7. Supply Current vs. Temperature
4
3.5
3
2.5
2
1.5
1
5V
2.7V
0.5
0
-45 -20 5 30 55 80 105 130
Temperature (°C)
Figure 9. Supply Current vs. Common-Mode Voltage
3
2.5
2
5V
Figure 8. Shutdown Current vs. Temperature
1000
100
10
1
0.1
-45 -20 5 30 55 80 105 130
Temperature (°C)
Figure 10. Input Voltage Noise vs. Frequency
1000
still valid
1.5
1
0.5
0
0 1 2
2.7V
3 4
Common-Mode Voltage (V)
ams
5
1
content
10 1000
Figure 12. Output Voltage vs. Output Current, sinking Figure 11. Output Voltage vs. Output Current, sourcing
10
5 1.75
5V
4.5
t<1s
1.5
t>10s
4 t>10s
1.25
t>10s
3.5
1
3 t<1s
2.7V
t<1s
2.5
0.75
2
0.5
2.7V
t<1s
0.25
5V t>10s
0
100 150
Output Current (mA)
200 250 0 50 100 150
Output Current (mA)
200
7 - 19 www.austriamicrosystems.com/Audio/OpAmps/AS1710_12 Revision 1.9
AS1710/AS1712
Datasheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s
Figure 13. Output Swing High vs. Temperature
100
90
Figure 14. Output Swing Low vs. Temperature
100
90
80
70
200
80
70
200
60
50
10mA
40
-45 -20 5 30 55 80 105 130
Temperature (°C)
Figure 15. Transient Response, 100mV, 10pF load
60
10mA
50
40
-45 -20 5 30 55 80 105 130
Temperature (°C)
Figure 16. Transient Response, 100mV, 100pF load
AG still valid
500ns/Div
Figure 17. Transient Response, 1V, 10pF load
ams
Figure 18. Transient Response, 1V, 100pF load
www.austriamicrosystems.com/Audio/OpAmps/AS1710_12 Revision 1.9
500ns/Div
8 - 19
AS1710/AS1712
Datasheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s
Figure 19. Transient Response, 2V, 10pF load Figure 20. Transient Response, 2V, 100pF load
500ns/Div
AG
500ns/Div
still valid
Technical
www.austriamicrosystems.com/Audio/OpAmps/AS1710_12 Revision 1.9
9 - 19
AS1710/AS1712
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
8 Application Information
8.1 Package Power Dissipation
Caution:
Due to the high output current drive, this op-amp can exceed the absolute maximum power-dissipation rating. Normally, when peak current is less than or equal to 40mA the maximum package power dissipation is not exceeded for any of the package types offered.
power dissipation:
P
PACKAGEDISS
V
RMS
I
RMS
COS
Where:
V
RMS
is the RMS voltage from V
DD
to V
OUT
when sourcing current, and from V
OUT
to V
SS
when sinking current.
I
RMS
is the RMS current flowing in or out of the op-amp and the load.
is the phase difference between the voltage and the current. For resistive loads, COS
= 1.
Figure 21. Typical AS1710/AS1712 Single-Supply Application
still
(EQ 1)
valid
V
IN
= 2V
P-P
C
R
–
+
3.6V
AS1710
AG
R
32
V
RMS
can be calculated as:
V
RMS
(V
DD
- V
content
DC
) + V
PEAK
/
Where:
V
DC
is the DC component of the output voltage.
V
PEAK
is the highest positive excursion of the AC component of the output voltage.
For the circuit shown in
:
V
RMS
= (3.6V - 1.8V) + 1.0V/
2 = 2.507V
RMS
I
RMS can be calculated as:
I
RMS
IDC + (IPEAK/
2)
Where:
I
DC
is the DC component of the output current.
I
PEAK
is the highest positive excursion of the AC component of the output current.
Technical
) + (1.0V/32
)/
2 = 78.4mA
P
PACKAGEDISS
= V
RMS
I
RMS
COS
RMS
= 196mW
Adding a coupling capacitor improves the package power dissipation because there is no DC current to the load, as shown in
.
(EQ 2)
(EQ 3)
www.austriamicrosystems.com/Audio/OpAmps/AS1710_12 Revision 1.9
10 - 19
AS1710/AS1712
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
8.2 60mW Single-Supply Stereo Headphone Driver
can deliver 60mW per channel with 1% distortion from a single 5V supply.
Figure 22. Stereo Headphone Driver Application (with Coupling Capacitor)
R
F
Audio In
Left
Audio In
Right
C
IN
V
BIAS
C
IN
R
IN
R
IN
–
+
AS1710
+
–
AS1710
+
C
OUT
+
C
OUT
R
F
AG
Headphone Jack to
32
Stereo Headset
still valid
, C
IN
and R
IN
form a high-pass filter that removes the DC bias from the incoming signal. The -3dB point of the high-pass filter is given by:
Choose gain-setting resistors R
C
OUT
IN
and R
F
ams
form a high-pass filter with the -3dB point determined by:
f
-3dB
= 1/(2
R
R
IN
C
IN
)
For a 32
load, a 100µF aluminum electrolytic capacitor gives a low-frequency pole at 50Hz.
(EQ 4)
(EQ 5)
8.3 Rail-to-Rail Input Stage
The AS1710/AS1712 CMOS op-amps have parallel connected N- and P-channel differential input stages that combine to accept a commonmode range extending to both supply rails. The N-channel stage is active for common-mode input voltages typically greater than (V
SS
+ 1.2V), and the p-channel stage is active for common-mode input voltages typically less than (V
DD
- 1.2V).
8.4 Rail-to-Rail Output Stage
The minimum output is within millivolts of ground for single- supply operation, where the load is referenced to ground (V
SS
shows the input voltage range and the output voltage swing of an AS1710 connected as a voltage follower. The maximum output voltage swing is load dependent although it is guaranteed to be within 500mV of the positive rail (V
DD
= 2.7V) even with maximum load (32
to ground).
Technical
www.austriamicrosystems.com/Audio/OpAmps/AS1710_12 Revision 1.9
11 - 19
AS1710/AS1712
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
Figure 23. Rail-to-Rail Input/Output Range, 100k
Figure 24. Rail-to-Rail Input/Output Range, 32
2.5µs/Div
V
CC
= 3.0V, R
LOAD
= 100k
2.5µs/Div
V
CC
= 3.0V, R
LOAD
= 32
valid
Note:
The absolute maximum ratings
(see page 3) for power dissipation and output short-circuit duration (10s, max) must be adhered to
since the output current can exceed 200mA
(see Typical Operating Characteristics on page 6) .
8.5 Input Capacitance
AG still
The parallel-connected differential input stages for rail-to-rail operation results in relatively large input capacitance C
IN
(6pF typ). This introduces a pole at frequency (2
R
C
IN
)-1, where R
is the parallel combination of the gain-setting resistors for the inverting or non-inverting amplifier and the amplifier exhibits degraded AC performance through either ringing in the step response or sustained oscillations.
Figure 25. Inverting and Non-inverting Amplifiers with Feedback Compensation
Inverting ams
C
F
R
= R
II
R
F
R
F
C
F
= RC
IN
R
F
V
IN
Non-Inverting
AS1710
V
OUT
R
V
IN
–
AS1710
+
V
OUT
R
F
C
F
R
The pole frequency is 10MHz when R
= 2k
. To maximize stability, R
<< 2k
is recommended.
To improve step response when R
> 2k
, connect a small capacitor (C
F
) between the inverting input and output. C
F
can be calculated by:
Where:
Technical
C
F
= 6(R/R
F
) [pf] (EQ 6)
R
F
is the feedback resistor.
R is the gain-setting resistor.
www.austriamicrosystems.com/Audio/OpAmps/AS1710_12 Revision 1.9
12 - 19
AS1710/AS1712
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
8.6 Driving Capacitive Loads
The AS1710/AS1712 amplifiers have a high tolerance for capacitive loads, and are stable with capacitive loads up to 100pF.
Figure 26. Capacitive-Load Driving Circuit
–
+
AS1710
R
ISO
C
F
still valid
Note:
Resistor R
8.7 Power-Up
ISO
AG
The AS1710/AS1712 typically settle within 5µs after power-up.
8.8 Shutdown
and their outputs are driven to V
SS
ams
SS
DD
= 2.7V), the amplifiers are disabled,
in shutdown, any pull-up resistor on the output causes a current drain from the supply.
Note: content
8.9 Power Supplies and Layout
The AS1710/AS1712 can operate from a single 2.7 to 5.5V supply or from dual ±1.35 to ±2.5V supplies. Good design improves device performance by decreasing the amount of stray capacitance at the op-amp inputs/outputs.
For single-supply operation, bypass the power supply with a 0.1µF ceramic capacitor.
For dual-supply operation, bypass each supply to ground.
Decrease stray capacitance by placing external components close to the op-amp pins, minimizing trace and lead lengths.
Technical
www.austriamicrosystems.com/Audio/OpAmps/AS1710_12 Revision 1.9
13 - 19
AS1710/AS1712
Datasheet - P a c k a g e D r a w i n g s a n d M a r k i n g s
9 Package Drawings and Markings
The devices are available in a SC70-5, SC70-6, and TQFN-16 (3x3mm) package.
Figure 27. SC70-5 Package
AAB
XXX
AG
aaa bbb ccc ddd
N
R
R1
1
E1 e e1
L
L1
L2
Symbol
A
A1
A2
D
E b c
-
-
-
-
Min
-
-
0.70
Nom
-
-
0.90
Max
1.10
0.10
1.00
0.15
0.30
0.08
0º
4º
-
2.00 BSC
2.10 BSC
1.25 BSC
0.65 BSC
1.30 BSC
0.26
0.10
0.10
0.36
0.42 REF
still
4º
-
-
0.25
8º
0.22
0.46
valid
12º
0.15
0.30
0.10
0.10
5
-
-
-
-
Notes:
Technical
1. Dimensions and tolerancing conform to ASME Y14.5M-1994.
2. All dimensions are in millimeters. Angles are in degrees.
3. Datums A and B to be determined at datum H.
www.austriamicrosystems.com/Audio/OpAmps/AS1710_12 Revision 1.9
14 - 19
AS1710/AS1712
Datasheet - P a c k a g e D r a w i n g s a n d M a r k i n g s
Figure 28. SC70-6 Package
AAA
XXX
AG
aaa bbb ddd
1 ccc
N
R1
R
E1 e e1
L
L1
L2
Symbol
A
A1
A2
D
E b c
Min
-
-
0.70
0.15
0.08
Nom
-
-
0.90
-
-
2.00 BSC
2.10 BSC
Max
1.10
0.10
1.00
0.30
0.22
-
0.26
-
-
1.25 BSC
0.65 BSC
1.30 BSC
0.36
0.42 REF
0.15 BSC
0.10
0.10
0º
4º
-
-
-
still
-
0.25
8º
12º
0.30
0.10
-
-
-
0.46
valid
0.10
-
6
Notes:
Technical
2. All dimensions are in millimeters. Angles are in degrees.
3. Datums A and B to be determined at datum H.
www.austriamicrosystems.com/Audio/OpAmps/AS1710_12 Revision 1.9
15 - 19
AS1710/AS1712
Datasheet - P a c k a g e D r a w i n g s a n d M a r k i n g s
Figure 29. TQFN-16 (3x3mm)
XXXX
AS08
Notes: ams
AG
1. Dimensions and tolerancing conform to ASME Y14.5M-1994.
2. All dimensions are in millimeters. Angles are in degrees.
Technical
aaa bbb ccc ddd eee e
D2
E2 fff
N
D
E
L b
A
A1
A3
still
Min
0.70
0
0.30
0.18
1.30
1.30
-
-
-
-
-
-
Nom
0.75
0.02
0.20 REF
0.40
0.25
3.00 BSC
3.00 BSC
0.50 BSC
1.45
1.45
0.15
0.10
0.10
0.05
0.08
0.10
16
1.55
1.55
-
-
-
-
-
-
Max
0.80
0.05
0.50
0.30
valid
16 - 19 www.austriamicrosystems.com/Audio/OpAmps/AS1710_12 Revision 1.9
AS1710/AS1712
Datasheet - P a c k a g e D r a w i n g s a n d M a r k i n g s
Revision History
Revision
1.8
1.9
Date
-
01 Aug, 2011
Owner
afe
Note:
Typos may not be explicitly mentioned under revision history.
Description
Initial revision
Updated Electrical Characteristics (page 4)
.
AG still valid
Technical
www.austriamicrosystems.com/Audio/OpAmps/AS1710_12 Revision 1.9
17 - 19
AS1710/AS1712
Datasheet
10 Ordering Information
The device is available as the standard products shown in Table 6
.
Table 6. Ordering Information
Ordering Code
AS1710A-ASCT
AS1710B-ASCT
AS1712A-AQFT
Marking
AAA
AAB
ASO8
Description
Single Op Amp with Shutdown
Single Op Amp
Quad Op Amp with Shutdown
Delivery Form
Tape and Reel
Tape and Reel
Tape and Reel
Package
SC70-6
SC70-5
TQFN-16 (3x3mm)
Note:
All products are RoHS compliant and austriamicrosystems green.
Buy our products or get free samples online at ICdirect: http://www.austriamicrosystems.com/ICdirect
Technical Support is available at http://www.austriamicrosystems.com/Technical-Support
For further information and requests, please contact us mailto:[email protected]
or find your local distributor at http://www.austriamicrosystems.com/distributor
AG still valid
Technical
www.austriamicrosystems.com/Audio/OpAmps/AS1710_12 Revision 1.9
18 - 19
AS1710/AS1712
Datasheet - O r d e r i n g I n f o r m a t i o n
Copyrights
Copyright © 1997-2011, austriamicrosystems AG, Tobelbaderstrasse 30, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered ®.
All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner.
All products and companies mentioned are trademarks or registered trademarks of their respective companies.
Disclaimer
Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. austriamicrosystems AG reserves the right to change specifications and prices at current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for each application. For shipments of less than 100
valid
parts the manufacturing flow might show deviations from the standard production flow, such as test flow or test location.
The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems AG rendering of technical or other services.
AG still
Contact Information
Headquarters
austriamicrosystems AG
Tobelbaderstrasse 30
A-8141 Unterpremstaetten, Austria
Tel: +43 (0) 3136 500 0
Fax: +43 (0) 3136 525 01
For Sales Offices, Distributors and Representatives, please visit: http://www.austriamicrosystems.com/contact
Technical
www.austriamicrosystems.com/Audio/OpAmps/AS1710_12 Revision 1.9
19 - 19
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
