RM-SERIES

Rackmount 100V mixer-amplifiers with Bluetooth

Item ref: 953.213UK, 953.214UK, 953.215UK, 953.216UK

User Manual

Version 3.2

Caution: Please read this manual carefully before operating

Damage caused by misuse is not covered by the warranty

Introduction

Thank you for choosing the Adastra RM-series rackmount 100V amplifier as part of your public address system. This amplifier is designed to offer high quality, dependable service for mobile and installed systems. Please read this manual fully and follow the instructions to achieve the best results with your new purchase and to avoid damage through misuse.

SAFETY SYMBOL AND MESSAGE CONVENTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS

RISQUE DE CHOC ELECTRIQUE NE PAS

OUVRIR

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

SAFETY NOTICE

1.

Prior to use, read through this manual

2.

Keep the manual in good condition

3.

Pay attention to safety warnings

4.

Observe all operating requirements

5.

Do not use the device near water or wet areas

6.

For cleaning, only use a lint-free, dry cloth

7.

Install according to the specifications

8.

Place away from heat sources or heating appliances

9.

Use mains lead provided and avoid damage to cable or connectors

10.

Unplug power from mains during stormy weather or if unused for long periods

11.

In case of malfunction, water ingress or other damage, consult qualified service personnel

12.

Do not place in damp areas or near liquids or moisture. Do not spill liquids on the housing

13.

Please pay attention to warning symbols during transit and placement

14.

Terminals marked with the symbol are HAZARDOUS LIVE and should only be connected by qualified personnel

15.

Ensure that the apparatus is connected to a mains socket with a protective EARTH connection

16.

Ensure correct operation of the mains switch

Warning

To prevent the risk of fire or electric shock, do not expose any components to rain or moisture.

If liquids are spilled on the casing, stop using immediately, allow unit to dry out and have checked by qualified personnel before further use. Avoid impact, extreme pressure or heavy vibration to the case

No user serviceable parts inside – Do not open the case – refer all servicing to qualified service personnel.

Safety

• Check for correct mains voltage and condition of IEC lead before connecting to power outlet

• Use double insulated speaker wire with adequate current rating for 100V speaker connections

• Only use one type of output – i.e. 4 - 16 Ω or 100V – do not mix or combine these outputs on a single zone or output

• Do not connect 4 - 16 Ω speakers to the 100V terminal or 100V speakers to the 4 - 16 Ω ter minal

• Do not allow any foreign objects to enter the case or through the ventilation grilles

Placement

• Keep out of direct sunlight and away from heat sources

• Keep away from damp or dusty environments

• For rack-mounting, use the rack ears provided and ensure adequate support for the weight of the amplifier

• Ensure adequate air-flow and do not cover cooling vents at the front and rear of the amplifier

• Ensure adequate access to controls and connections

Cleaning

• Use a soft cloth with a neutral detergent to clean the casing as required

• Use a vacuum cleaner to clear ventilation grilles of any dust or debris build-ups

• Do not use strong solvents for cleaning the unit

RM Series User Manual

Front panel

1. USB/SD/FM/BT media player

2. MIC 1 volume control

3. MIC/LINE 2 volume control

4. MIC/LINE 3 volume control

5. LINE 4 volume control

6. LN5/USB volume control

Rear panel

7.

8.

9.

10.

11.

12.

BASS EQ control

TREBLE EQ control

MASTER volume control

VU level meter

POWER on/off switch

Speaker zone selector buttons (RM240S/RM360S only)

13. Mains voltage switch

14. IEC mains inlet & fuse holder

15. DC power terminals

16. COM speaker terminal

21. LINE 4 input (RCA)

22. MIC/LINE 3 input (6.3mm jack)

23. MIC/LINE 2 input (6.3mm jack)

24. DIP switches (see DIP switches section below)

17. 4 - 16 Ω speaker terminal

18. 100V speaker terminals (1 zone for RM60 / RM120)

19. LINE OUT connectors (RCA)

20. LINE 5 input (RCA)

25. MIC 1 input (balanced XLR)

26. 24V Mute contacts

27. Antenna connection for FM tuner

DIP switches (24)

MIC 1 channel has an option for +20V phantom power for condenser microphones and paging microphones with chimes.

MIC 1 also has the option of VOX control, which attenuates the line input channels 4 and 5 by -40dB when MIC 1 signal is detected and returns them to normal when MIC 1 signal is silent.

MIC/LINE 2 (23) and MIC/LINE 3 (22) inputs can be set to MIC (up position) or LINE (down position) sensitivity to suit the type of input being used. Be sure to make these DIP switch settings when the amplifier is switched off. Making any changes when the amplifier is powered up may cause loud noises which can damage the speakers.

RM Series User Manual

Connection and setup

Connect the rear IEC inlet (14) to the mains using the supplied mains lead (or an equivalent approved type).

Ensure that the correct voltage is indicated on the voltage selector (13) and the mains outlet is switched on.

Alternatively, the amplifier can be powered by a 24V battery, such as a lorry or boat battery, by connecting the “+” and “ ” of the battery to the DC INPUT (15) on the rear panel. Ensure that DC cables are capable of handling the required current (10A min. recommended)

The RM series amplifiers have a total of 5 input channels. MIC 1 input (25) is fed to a dedicated microphone channel. Connect the main announcement microphone to this channel using a balanced XLR lead.

Connect microphones or mono line inputs to MIC/LINE 2 and MIC/LINE 3 inputs (23, 22) using good quality

6.3mm jack leads. Make sure the correct sensitivity is selected for the type of input source.

Connect any other line level audio inputs to the LINE 4 (21) and LINE 5 (20) connectors on the rear panel using good quality RCA leads. Since RM series amplifiers have a mono output, stereo signals will be summed together.

Further mixer-amplifiers or slave amplifiers can be connected from the rear LINE OUT sockets (19), again using a good quality RCA lead. This output carries the full mix of all channels 1-5 as fed to the speakers.

Speaker outputs

The RM series amplifiers can be used either as 100V line amplifiers or standard low impedance power amplifiers. These 2 configurations cannot be used together, so it is important to decide which method will be used at the start.

100V line systems

For 100V line systems, connect the amplifier to the first speaker in the system using double-insulated speaker wire which has adequate current rating to handle the total output of the amplifier.

C onnect the “100V” (18) output terminal to the positive (+) connection of the speaker and “COM” output (16) to the negative (-) connection of the speaker. Connect further speakers in parallel to the first speaker with all positive terminals and connected together and all negative terminals connected together as shown below.

A 100V line speaker system can comprise of many speakers connected together. The determining factor for how many speakers can be used on a single amplifier is the power rating. For most purposes, it is advised to connect as many speakers as needed with a combined wattage of no more than 90% of the am plifier’s output power rating.

The terminals of a 100V speaker are connected to a transformer and in some cases, this transformer may be

“tapped” for different power ratings. These tappings can be used to adjust the wattage (and output volume) of each speaker in the system to help achieve the ideal total power of the system for the amplifier.

RM Series User Manual

Speaker switching zones (RM240S and RM360S)

The RM240S and RM360S have 4 separate terminals for 100V speakers. Any 100V speakers connected to the terminals labelled 100V or ZONE 1 / ZONE 2 / ZONE 3 / ZONE 4 (+) and COM (-) will be governed by 4 front panel speaker switches (12)

(e.g. a speaker connected to ZONE 1 + COM will be enabled if Zone 1 button is depressed on the front panel)

There is also a switch labelled “ ALL ” on the front panel which enables output to all zones 1 to 4.

Low impedance systems

Alternatively, RM series amplifiers can be used to drive low impedance speakers by connecting the “ 4 - 16 Ω” terminal (17 ) to the positive (+) speaker connection and “COM” terminal (16) to the negative (-) speaker connection.

It is important to ensure that the total combined speaker load is no less than 4 Ω and that the combined power handling of the speakers is equal to or greater than the output power of the amplifier.

(e.g. a pair of 8Ω speakers connected in parallel combine to make a 4Ω load)

Do not use 4 - 16 Ω and 100V at the same time.

Emergency mute function

RM series mixer-amplifiers are equipped with a Euroblock connector for a 24V mute function (26).

These contacts can be wired to an emergency panel (such as a fire alarm) which has a 24V trigger output.

When the alarm is activated, the RM mixer-amplifier will mute all channels except for MIC1, which remains active for emergency announcements.

Operation

When all connections to the amplifier are made, turn all rotary controls down and switch on the power (11) and a power “ON” LED will illuminate.

Turn BASS and TREBLE controls (7, 8) to the 12 o’clock position (pointing straight up) and turn the MASTER rotary control (9) up part way for testing.

Ensure a signal is being fed to one of the line inputs 2, 3, 4 or 5 and gradually increase the volume control for that channel until the output is heard through the speakers.

Turn up the MASTER to the maximum required volume level and reduce the channel volume control if necessary.

Repeat this process for any other line inputs connected to channels 2, 3, 4 or 5.

Note: If a line input is not connected to an RM series mixer-amplifier, the initial test can be made using the built-in media player. See the “Media player” section for instructions.

Both the media player output and LINE 5 input are governed by the LN5/USB volume control.

The output of the amplifier is represented on the VU meter LEDs (10) and care should be taken that the red

“0” LED is only lit momentarily during use. Anything longer than a short flash of this LED may be indicating distortion or clipping of the output signal and the MASTER volume control or channel volume control should be turned down.

RM Series User Manual

If a microphone is connected to MIC 1 input, make sure it is switched on and if it requires phantom power, make sure this feature is enabled on the DIP switch. Gradually increase the MIC 1 control (2) whilst speaking into the microphone until the required volume level is reached.

The microphone should not be able to “hear” the speakers, which can cause feedback (squealing or howling)

Repeat this process for microphones or line inputs connected via the MIC/LINE 2 and 3 inputs.

If the VOX feature is enabled, audio playback through channels 4 and 5 will be reduced in volume automatically when speaking into MIC 1.

In addition to channel and MASTER volume controls, there are BASS and TREBLE EQ controls (7, 8) to adjust the tone of the overall output. At the 12 o’clock posit ion, these controls apply no effect to the signal (no boost or cut).

Moving the BASS control clockwise boosts the low frequencies in the audio, whilst moving it anticlockwise will cut these low frequencies. Likewise, moving the TREBLE control clockwise boosts the high frequencies in the audio, whilst moving it anticlockwise will cut these high frequencies.

Adjust these EQ controls to suit the type of audio signal or compensate for the room acoustics.

Media player

28. SOURCE select button

29. Previous / volume down button

30. Play / pause button

31. Next / volume up button

32. REPEAT mode button

33. MUTE button

34. Media player display

35. SD card slot

36. USB input

RM60, RM120, RM240S and RM360S mixer-amplifiers are fitted with a built-in media player. This section comprises a Bluetooth receiver, USB/SD audio player and FM tuner.

Pressing the SOURCE select button (28) will step through Bluetooth, USB, SD card and FM tuner modes.

Bluetooth

The Bluetooth function allows connection of a smart phone or tablet to the media player section for playback of stored files or streamed digital audio.

In order to enable this function, it will be necessary to pair the sending device to the receiver as follows.

1.

Open the Bluetooth settings menu on the smart phone or tablet (or other sending device)

2.

Scan for Bluetooth devices and look for “adastra 0000 ” in the list of available devices

(ensure that the RM amp is powered on and within reception range)

3.

Select “adastra 0000 ” and the sending device should confirm that it is connected as an audio device .

(note that “0000” may be a different number if it has been edited – see below)

4.

Play audio from the sending device, ensuring that volume controls are not turned down/muted

5.

Turn up the LN5/USB volume control on the amplifier to the required level.

RM Series User Manual

The Previous, Next and Play/pause buttons will operate in Bluetooth as remote playback controls. Holding the

Previous track or Next track buttons (29, 31) will adjust the output volume of the player.

The Bluetooth name can be customized to enable identification of individual nearby amplifiers.

To customize the Bluetooth number press and hold the Play/Pause button until adastra 0000 is displayed with one of the characters flashing. Press Previous or Next buttons to edit the number and Play/Pause to select another character. Hold Play/Pause to store the ID and exit.

Note: Android devices have the facility to re-name devices within the Bluetooth settings menu.

If the Bluetooth ID has been re-named on the Android device, editing the Bluetooth ID on the media player will not affect the name displayed on that Android device.

FM Tuner

The FM tuner function operates in the same way as a standard FM radio and benefits from the connection of an FM antenna to the rear panel ‘F’ type connector.

To auto-tune available stations, press and hold the Play/Pause button to begin auto tuning, which scans available stations and automatically stores them as channels within the FM tuner.

Alternatively, to tune the station presets manually, press the Play/Pause button briefly to enter manual tuning mode (MANU). Use Previous/Next track buttons to select the desired frequency and press REPEAT, then use

Previous/Next track buttons to select the preset and press REPEAT again to store the frequency in that preset

(display will show “ OK ” ). Repeat for all ten presets P01 to P10. Press MUTE to exit the manual tuning mode.

To step through pre-set stations, press the Previous or Next buttons.

Hold down the REPEAT button to delete a stored station.

Holding the Previous track or Next track buttons will adjust the output volume of the player.

USB/SD player

When a USB memory stick is inserted into the USB port (36) or SD card into the SD slot (35), the USB or SD symbol will show in the display and any compressed audio files will start to play automatically. The last connected media will take priority.

If playback does not start automatically, press the SOURCE select button (28) and Play/Pause button (30) to check if the player is set to the correct mode. Try Previous track and Next track buttons (29, 31) if the selected track is unable to play. Check that the audio files are mp3 type.

Turn up USB/LN5 volume control to hear the output from the speakers and increase to the required level.

There are 3 Repeat modes: Repeat all tracks, Repeat single track and Random play.

Pressing the “REPEAT” button (32) will c ycle through these modes as shown in the top right of the display.

Pressing the Previous track button (29) briefly steps backwards through tracks on the memory device. Press and hold this button to decrease the playback volume.

Pressing the Next track button (31) briefly steps forwards through tracks on the memory device.

Press and hold this button to increase the playback volume.

To pause the current track, press the Play/Pause button (30) and press it again to resume playback.

The display shows the track number when a track is selected and then elapsed time during playback

To avoid loud pops through the speakers, turn down the MASTER control before powering down.

RM Series User Manual

Specifications

Power supply

Output power: RMS

Outputs : Speaker

Output: Line

RM60

110/230Vac, 50/60Hz (IEC) or 24Vdc option (screw terminals)

60Wrms

RCA signal output

RM120

120Wrms

100V / 4 - 16 Ω / COM

RM240S RM360S

240Wrms 360Wrms

4x100V / 4 - 16 Ω / COM

Inputs

Volume controls

Mic XLR, 2 x mic/line jack, 2 x RCA line, 24V mute contacts, RF antenna

Mic1, mic/line2+3, line4+5 (USB), master

Equalizer : Bass / Treble 100Hz ±10dB / 10kHz ±10dB

Bluetooth version

Phantom power

THD

Dimensions

Weight

Troubleshooting

2.0

+20V (MIC 1 input)

<1.0%

433 x 320 x 89mm

5.98kg 8.36kg 9.62kg

433x410x89mm

12.68kg

No power LED on control panel

Power LED is on but no other LEDs and no output

Power light and output LEDs lighting but no output

Ensure IEC lead is in good condition and connected properly

Ensure POWER switch is on and check mains inlet fuse

Check input signals and condition of input connection leads

Check MASTER, MIC, LINE or USB/SD volume controls are turned up

Check speaker output terminals are connected correctly

Check speakers are working (test on another amp if available)

Check memory device is connected properly (remove and re-insert)

Check file types – standard mp3 digital audio files required

Check memory device works on a PC or Mac for standard playback

Ensure that Bluetooth is enabled on sending device

Bluetooth cannot connect

No audio from Bluetooth device

Output too loud or distorted

Output too quiet or inaudible

No microphone output

Feedback from microphone

Amplifier overheating

Ensure that the sending device is within Bluetooth range (5-10m)

Check that “adast ra **** ” is the connected device

If there are more than one “adastra **** ” devices, check each in turn

If one of many “adastra **** ” devices, edit the Bluetooth ID

Ensure that volume controls are not turned down on sending device

Check volume and Play/Pause buttons in case Bluetooth is muted

Reduce MIC, LINE IN, USB/SD and/or MASTER level

Ensure Hi-Z line level input(s) not connected via MIC input

Increase MIC, LINE IN, USB/SD and/or MASTER level

Check for quiet recording of media files on USB

Check VOX override is not unintentionally suppressing audio playback

Check phantom power is enabled if using a condenser microphone

Face microphone away from speakers and monitors and reduce level

Ensure cooling vents are clear from debris and dust

Check that 4, 8 or 16 Ω speakers are not connected to 100V terminals

Ensure total 100V speaker wattage is lower than amplifier rating

Ensure that 100V and 4, 8 or 16 Ω speakers are not both connected

Ensure that total load connected to 4 - 16 Ω ou tput is not less than 4 Ω

Disposal: The “Crossed Wheelie Bin” symbol on the product means that the product is classed as Electrical or

Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life.

The goods must be disposed of according to your local council guidelines.

Errors and omissions excepted.

Copyright© 2019. AVSL Group Ltd.

RM Series User Manual