Titan 80 LB ATV & UTV Broadcast Spreader Manual

-

MPN(s): 80BCSPRDR

SKU(s): 191359

UPC(s ): 840009210785

SAFETY WARNINGS AND PRECAUTIONS

Warning: When using tool, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Read all instructions before using this tool!

1. Keep work area conditions. Cluttered areas invite injuries.

2. Additional work area conditions.

Do not use machines or power tools in damp or wet locations. Do not expose to rain. Keep work area well lighted.

3. Keep children away. Children must never be allowed in the work area. Do not let them handle machines, tools or extension cords.

4. Store idle equipment. When not in use, tools must be stored in a dry location to inhibit rust. Always lock up tools and keep out of reach of children.

5. Use the right tool for the job. Do not attempt to force a small tool or attachment to do the work of a larger industrial tool. There are certain applications for which this tool was designed. It will do the job better and more safely at the rate for which it was intended. Do not modify this tool and do not use this tool for a purpose for which it was not intended.

6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically non-conductive clothes and non-skid footwear are recommended when working. Wear restrictive hair covering to contain long hair.

7. Use eye protection.

Always wear ANSI approved impact safety glasses underneath a full face shield during use. Also, wear heavy duty work gloves.

8. Do not overreach.

Keep proper footing and balance at all times. Do not reach over or across running machines.

9. Maintain tools with care.

Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. The handles must be kept clean, dry and free from oil and grease at all times.

10. Remove adjusting keys and wrenches.

Check that keys and adjusting wrenches are removed from the tool or machine work surface before starting work.

11. Stay alert.

Watch what you are doing, use common sense. Do not operate any tool when you are tired.

12. Check for damaged parts . Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Any part that is damaged should be replaced.

13. Replacement parts and accessories.

When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool.

14. Do not operate tools if under the influence of alcohol or drugs.

Read warning label on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool.

WARNING:

The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator.

2

SPECIFIC SAFETY RULES

1- Always wear protective clothing, eyewear, and dust mask to prevent contact with chemical and other materials being applied with this machine.

2- Remove any material in hopper before lifting or detaching this machine from the vehicle.

3- Care must be taken when lifting this machine so as not to cause personal injury or equipment damage. Never attempt to install this machine to the vehicle alone. Recruit the help of someone to assist when attaching and detaching this machine from the vehicle.

4- Refer to the material packaging or the Material Safety Data Sheet for precautionary measures required when handling materials to be applied.

5- Before attaching this machine, consideration must be given to the load capacity of the vehicle. Refer to the owner’s manual of the vehicle for rated load capacity. Be sure to take into account the weight of this machine

20lbs and the weight of the material to be placed in the hopper when calculating the total load.

6- Keep hangs away from any spinning object.

HOW TO OPERATE SAFETY

1- Read, understand, and follow all product label information provided on the material being applied.

2- An adjustable solid stop is provided that allows the operator to adjust to the desired opening position on the rate setting control prior to operation of the vehicle. This allows repeatability to the stop without the need to look at the control while operation the vehicle.

3- Establish the correct rate and then lock the stop in that position using the thumb wing nut on the setting control.

PRODUCT SPECIFICATIONS

1- 12 Volt motor with vinyl coating mounts to front or rear luggage rack, lever and gauge mounts to either side.

2- Fits most brands of ATVs and comes with wiring harness for easy installation.

3- Heavy 80-Lb <36kg> load bearing capacity.

4- Capacity:1900 cu.in.

UNPACKING

INSTRUCTIONS

When unpacking the tools:

1-

Carefully remove the tool and accessories from the box.

2-

Make sure that all items listed in the packing list are included.

3-

Inspect the tool carefully to make sure no breakage or damage occurred during shipping.

WARNING: If any parts are missing do not operate the tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury.

4-

Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool.

3

4

18

19

20

21

22

13

14

15

16

17

10

11

12

7

8

5

6

9

27

28

29

23

24

25

26

PARTS LIST

REF# DESCRIPTION

3

4

1

2

Rain Cover

Electric Motor Lid

Electric Motor

Electric Motor Cover

Tie

Lock Nut M6

Motor Support

Hopper Assembly

Flat Washer Ø6

Hex Bolt M6x16

Wire Clamp

Fixing Plate

Rivet Ø5x13

Wood Screw M5x35

Center Spacer

Turning Plate

Adjustment Plate

Round Head Screw M4x20

Round Head Screw M6x45

Carriage Bolt M6x25

Frame

Gauge Assembly

Spacer

Wing Nut M6

Adjust Handle

Lock Washer Ø5

Screw M5x16

Adjustment Wire

Round Head Screw M6x16

1

2

1

2

1

2

1

1

1

2

1

2

1

1

4

4

1

2

1

1

1

1

1

2

4

QTY

1

1

1

1

5

33

34

35

36

30

31

32

37

38

39

Lock Washer Ø6

Wire Assembly

Hex Nut M6

Press Plate

J-Bolt

Round Head Screw M5x16

Wire Clamp Press Plate

Nylon Lock Nut M5

Flat Washer Ø5

R Pin

2

2

4

8

2

1

8

4

4

1

6

ASSEMBLY

1- Attach frames to hopper as shown using

M5x35 Wood Screws (#14).

2- Connect the rate control assembly to the frame using the Round Head Screw M6x45

(#19) and Wing Nut M6 (#24).

3- Position the rate control assembly to either frame rail based on if the spreader is mounted to the front or the rear rack. If mounted on front rack the control should be positioned to the left rail, if mounted on the rear rack the control should be positioned on the right rail.

Unassembled Gauge

Head screw

M6x45(#19)

Assembled Gauge

Wing nut

M6(#24)

How to attach to your ATV

 Position the assembled spreader centered on either the front or rear luggage rack on your ATV. Next using the included “J-Bolts”, connect the rear cross bars to the luggage rack cross bar closet to the seat or handlebars. Using the 2 included “Double J-Bolts”, attach the spreader to the luggage rack securing it to the outer most rail on the luggage rack. Tighten all fasteners and cut any excessive bolt lengths that extend beyond the nuts on the “U & J-Bolts” and smooth if necessary.

WARNING: Prior to each use, inspect the mounting hardware and the spreader to ensure the rigidity of the mount by tightening any loose hardware either on the

Spreader or Luggage Rack mounts.

7

8

This concludes the 80BCSPRDR Owner’s Manual.

If applicable to your product, make sure to tighten all nut-and-bolt combinations before use.

Enjoy!

DISCLAIMER

This equipment must be used with care by capable and competent individuals under supervision, if necessary.

The use of any equipment, including this one, involves the potential risk of injury. You accept and assume full responsibility for any and all injuries, damages (both economic and non-economic), and losses of any type, which may occur, and you fully and forever release and discharge Titan, its insurers, employees, officers, directors, associates, and agents from any and all claims, demands, damages, rights of action, or causes of action, present or future, whether the same be known or unknown, anticipated, or unanticipated, resulting from or arising out of the use of said equipment.

TITAN MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE EQUIPMENT, INCLUDING ANY WARRANTY OF

MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, WHETHER EXPRESS OR IMPLIED BY LAW,

COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE. BUYER ASSUMES ALL LIABILITY IN

USE OF THE EQUIPMENT.

NEED HELP?

CONTACT US FIRST.

1 (800) 605 8241

[email protected]

/

Business Hours: Monday

–

Friday • 8:00 a.m.

–

5:00 p.m. (CT)

9