Taurus TX™ 22 Owner Manual
Taurus TX™ 22 is a semi-automatic pistol chambered in .22LR. It features a 16-round magazine capacity, a matte black finish, a hard anodized slide, and an adjustable rear sight. The TX™ 22 is also equipped with a trigger safety, an ambidextrous manual safety, and a striker block for added safety. This pistol is ideal for target shooting, plinking, and self-defense.
Reklama
Reklama
INSTRUCTION MANUAL
GENERAL SAFETY, OPERATING INSTRUCTIONS
AND LIMITED WARRANTY
READ CAREFULLY BEFORE USING YOUR FIREARM
Important: Keep this manual with your firearm.
The information contained in this manual is useful, both for beginners and experienced shooters. In addition to important information about the function, cleaning and care of the firearm, this manual contains instructions that may be very helpful in shooting safely.
The most important rule of safe firearm handling is always keep the muzzle pointed in a safe direction!
TaurusUSA.com
/TaurusUSA
• Available in .22LR
• 16 round and 10 round capacity
• Matte black finish
• Hard anodized slide
• Single action
• Adjustable rear sight
• Trigger safety
• Ambidextrous manual safety (Optional)
@taurususa /TaurusUSA
2
Always keep the muzzle pointed in a safe direction and finger off the trigger.
CONTENTS
Firearm Safety ...................................................... 6
Get To Know Your Pistol...................................... 14
Ammunition ....................................................... 20
Operating Instructions ....................................... 24
Disassembly ....................................................... 28
Assembly ............................................................ 31
Care and Maintenance ........................................ 34
Exploded View .................................................... 38
Taurus® Service .................................................. 42
Limited Warranty ............................................... 44
WARNING
The safety warnings in this booklet are important. By understanding the dangers inherent in the use of any firearm, and by taking the precautions described herein, you can safely enjoy your
Taurus
®
firearm. Failure to follow any of these warnings may result in serious injury to you or others, as well as severe damage to the firearm or other property.
Always keep the muzzle pointed in a safe direction and finger off the trigger.
3
NOTES
Intentionally left blank
4
Always keep the muzzle pointed in a safe direction and finger off the trigger.
SIGNAL WORDS AS DEFINED BY
ANSI Z535.6 AND Z535.4 STANDARDS.
DANGER
WARNING
CAUTION
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to physical injury.
Always keep the muzzle pointed in a safe direction and finger off the trigger.
5
FIREARM SAFETY
WARNING
When a firearm discharges, the bullet or shot can strike a person, resulting in death or serious bodily injury.
The three basic keys to safe handling of firearms:
1. KEEP YOUR FINGER OFF THE TRIGGER UNTIL YOU ARE READY TO FIRE.
If you maintain good trigger discipline, it is extremely unlikely the firearm will fire.
2. KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
Even if the firearm discharges, if the muzzle is pointed in a safe direction, no one will be injured.
3. NEVER TRUST ANY SAFETY MECHANISM.
If you adopt the attitude that you will not trust any safety mechanism, you will be vigilant about keeping your finger off the trigger and keeping the muzzle pointed in a safe direction.
WARNING - KNOW YOUR TARGET
Never fire at targets at close range. Ricochets can and do cause death or serious bodily injury. What constitutes “close range” depends on many factors including target material, bullet caliber and angle of impact.
KNOW WHAT IS BEHIND YOUR TARGET.
Unless you are shooting into a bullet trap designed to capture the type of ammunition you are firing, projectiles may pass through the target and strike anyone or anything beyond. Bullets can travel miles.
6
Always keep the muzzle pointed in a safe direction and finger off the trigger.
ALWAYS WEAR HEARING PROTECTION.
Firearms are loud. The sound they generate is greater indoors. Repeated exposure to loud noises can cause deafness. Hearing protection is rated by decibel reduction. Look for “dB” reduction of 30 or more when purchasing ear protection. Modern ear protection can allow normal hearing until the sound from the discharge reaches the ear. Layering hearing protection, for example, wearing 30db rated foam plugs with 20db rated ear muffs, significant protection can be achieved.
ALWAYS WEAR EYE PROTECTION.
In normal operation, firearms emit hot high-velocity gases, particles and metal. These materials flying into your eye can cause blindness. Protect your vision with proper eye protection. Any eye protection may be better than none, but look for ANSI Z87.1-2003 certified eyewear for the best protection.
NEVER HANDLE FIREARMS WHILE UNDER THE INFLUENCE OF DRUGS OR ALCOHOL.
Firearms are dangerous. Handling firearms while impaired by drugs or alcohol is foolhardy and may result in serious injury or death. This warning includes prescription drugs that contain a warning about using machinery or driving while taking the medication.
MODIFIED FIREARMS ARE DANGEROUS, AND USE CAN RESULT IN SERIOUS INJURY OR DEATH.
“Trigger jobs,” polishing original components or installing aftermarket parts can cause a firearm to function in ways different than intended. Some such work may also be illegal.
DAMAGED FIREARMS ARE DANGEROUS, AND USE CAN RESULT IN SERIOUS INJURY OR DEATH.
Repairs should always be made by a qualified gunsmith or by a factory-authorized repair site. Work done by those unfamiliar with the design can cause a firearm to function in ways different than intended.
NEVER ATTEMPT TO DISASSEMBLE OR CLEAN A LOADED FIREARM. DOING SO CAN RESULT IN
SERIOUS BODILY INJURY OR DEATH.
How often have we heard “But it went off while I was cleaning it!” or, “I did not know it was loaded!” or, “It was jammed, and I tried to take it apart!”?
IF A FIREARM GOES OFF, THERE WAS A ROUND OF AMMUNITION IN THE CHAMBER.
Period.
“Clear” (or empty) the firearm of all ammunition before disassembling or cleaning.
Always keep the muzzle pointed in a safe direction and finger off the trigger.
7
As owner of your new Taurus® firearm, you are responsible for (1) keeping your finger off the trigger, (2) pointing the muzzle in a safe direction, (3) removing the magazine, (4) pulling the slide to the rear and locking it back and (5) looking and feeling in the magazine well and chamber to confirm the pistol is empty.
An empty firearm cannot fire.
FIREARM SAFETY SYSTEMS
Firearm safety is supported by a system. With your pistol, the system is made up of the following:
1. You! Your involvement in safety cannot be overemphasized. No safety component can keep your finger off the trigger and the muzzle pointed in a safe direction. Also, you are the key to never trusting any of the mechanical parts of the safety system.
2. Manual Safety (on certain TX22 models). If your firearm is equipped with, always use the manual safety. When you need it to work, it needs to be all the way in the Safe position, not half way or at some other point in its travel. Don’t play with the manual safety and you will avoid accidents.
WARNING
Safe firearm handling must still be followed with safety activated.
3. Trigger Safety. The trigger safety serves the same kind of function as the manual safety. It must be in the Fire position to fire the pistol. With a trigger safety, the safety moves to the Fire position when you press the trigger.
4. Striker Block. The striker block interferes with the forward travel of the striker until the trigger is pulled.
Like a trigger safety, pressing the trigger moves this safety component from its “safe” (blocking) position to its “fire” (free) position.
5. Trigger Guard. This is a physical obstruction that helps prevent unintended pressing of the trigger or trigger safety. Do not modify the trigger guard.
6. This Manual. Taurus intends for you to use this manual to learn about your pistol and to help you use your pistol safely. If you use the manual, you will be a long way toward being a knowledgeable and safe firearms owner.
Firing Position Safety Position
8
Always keep the muzzle pointed in a safe direction and finger off the trigger.
Always keep the muzzle pointed in a safe direction and finger off the trigger.
9
PISTOL AND REVOLVER SIZE AND SAFETY
The selection of a revolver versus a pistol as well as the size, caliber and magazine capacity of a handgun are personal choices. There are many choices to be made, and there are advantages and disadvantages for each. When selecting a pistol, size has safety implications because of the way pistols are loaded.
Generally speaking, smaller handguns may require more attention to be handled safely than medium or full-size handguns. This is because their small size makes it easier to point the muzzle at your hand or to
“sweep” (swing the muzzle across your body) yourself in ordinary handling.
When chambering a round, we recommend pulling the slide to the rear by gripping the rear of the slide, with the muzzle pointed straight and away from your body and in a safe direction.
SAFE CARRY CONDITION
“Safe Carry Condition” is the most ready-to-fire condition that the user feels is reasonable under the circumstances. Generally, we believe that Taurus pistols should be carried with a full magazine and an empty chamber. Under most circumstances, this provides the best balance of readiness and safety. On the plus side, if the chamber is empty, unintended discharges are minimized. However, the slide must be manipulated to load a round in the chamber. In emergency circumstances, this can be difficult to do safely and correctly.
If the user believes that he or she is faced with an increased threat, chambering a round is appropriate. For safety reasons, this should be done beforehand with the muzzle pointed in a safe direction, your finger off the trigger. If equipped, place the manual safety in the “safe” position. How do you know you may be going into a more dangerous situation? That depends. If, for example, you carry cash to deposit after a business closing, this may well qualify. If a domestic partner is actively threatening you, this may qualify as well.
“Safe Carry Condition” is a judgment call and must be made by the user. Some users routinely face greater threats than others. Users must be aware of their situation and circumstances. Errors in judgment can have dire and tragic outcomes if firearms are present.
10
Always keep the muzzle pointed in a safe direction and finger off the trigger.
Always keep the muzzle pointed in a safe direction and finger off the trigger.
11
CARRYING FIREARMS
Carrying a firearm can be dangerous. Carrying a firearm makes it more difficult to control the muzzle and makes it more likely that the firearm can be dropped or bumped causing the firearm to fire.
In almost all circumstances, it is safest to carry a handgun in a holster designed for that specific handgun.
Carrying a handgun in a pocket without a specific designed In-Pocket Holster or a trigger shield or in a waist band without a belt clip is always a last choice. Carrying any handgun in a holster that fits the firearm and style of carry should prevent it from accidentally falling and you from losing control of the muzzle.
Except in rare high-threat circumstances, carry your pistol with a full magazine and an empty chamber.
If the chamber is empty, the pistol cannot fire.
WARNING - CARRYING
Do not carry your firearm in any way that might let it fall or be bumped. If a firearm falls or is bumped, it may fire.
WARNING - CARRYING
Always review and follow the holster or luggage manufacturer’s instructions or the firearm may fall or be bumped and fire.
FIREARM STORAGE AND GUN LOCKS
How you secure your firearm is a personal choice based on the unique circumstances in your home, business or vehicle and the laws of the state where your firearm is located. Any choice you make about securing your firearm will present advantages and disadvantages. You must weigh those advantages and disadvantages and choose which security method is best for you and those around you.
WARNING - LOCKING
Never lock a firearm with a round of ammunition in the chamber. Unlocking a loaded firearm makes it more difficult to maintain trigger discipline and to keep the muzzle pointed in a safe direction.
WARNING
Securing your firearm may inhibit access in a defensive situation and may result in injury or death.
WARNING
Failure to secure a firearm may result in injury or death. Properly securing a firearm means storing your firearm unloaded, decocked and securely locked, with all ammunition in a separate location.
12
Always keep the muzzle pointed in a safe direction and finger off the trigger.
Always keep the muzzle pointed in a safe direction and finger off the trigger.
13
GET TO KNOW YOUR PISTOL
SLIDE
REAR SIGHT
DISASSEMBLING LATCH
BARREL
FRONT SIGHT
MANUAL SAFETY
(ON CERTAIN
MODELS)
MAGAZINE
RELEASE
TRIGGER
TRIGGER
GUARD
GRIP
MAGAZINE
SLIDE CATCH
14
Always keep the muzzle pointed in a safe direction and finger off the trigger.
SPECIFICATIONS
Model
Caliber
Action
Capacity
Barrel Length
Overall Length
Overall Height
Overall Width
Weight
Sights
Materials
Safety Devices
Finish
Remarks
TX22
.22LR
TX22 Competition
Single Action
16 Rounds/10 Rounds
4.1"
7.06"
5.25"
8.21"
5.44"
1.25" (at widest point)
17.3 oz.
23.2 oz
Adjustable: 3 White Dot System Adjustable: 3 White Dot System and
Red Dot Mounting System
Slide: High Grade Aluminum
Barrel: Alloy Steel
Grip: Polymer
Striker Block, Trigger Safety, Manual Safety (on certain models)
Hard Anodize Black
Accessory Rail (Picatinny MIL-STD-1913)
Always keep the muzzle pointed in a safe direction and finger off the trigger.
15
SIGHT ADJUSTMENT
NOTICE
To adjust, make sure the firearm is unloaded and always keep the muzzle pointed in a safe direction.
If possible, leave the slide open (full rearward position) during adjustment.
ELEVATION ADJUSTMENT
The rear sight can be adjusted in elevation to raise or lower the point of impact. When raising the sight, the point of impact rises. Lowering the sight, the point of impact is lowered.
The sight adjustment does not have a stop at the end, so while adjusting the sight you must pay attention to the click according to the sight movements (up or down).
WINDAGE ADJUSTMENT
The rear sight can also be adjusted for windage. Turn the windage adjusting screw clockwise to move the notch, and point of impact, to right side. Turn the windage adjusting screw counter-clockwise to move the notch, and point of impact, to left side.
16
Always keep the muzzle pointed in a safe direction and finger off the trigger.
Always keep the muzzle pointed in a safe direction and finger off the trigger.
17
LOCKING DEVICE INSTALLATION INSTRUCTIONS
WARNING - LOCKING DEVICES
• Always keep your firearm pointed in a safe direction, including when you are installing or removing your locking device.
• Always verify that your firearm is completely unloaded (see page 28) before installing your locking device.
• Do not install locking devices in the trigger guard; always keep your fingers and locking device outside the trigger guard during device installation and removal.
• Store firearms, ammunition and keys separately and securely, away from children and careless adults; do not store your firearm with the keys in the locking device.
• Do not attempt to work the action of your firearm with the locking device in place; this may damage your firearm.
• While locking devices are an important aid to security measures, they are not a substitute for safe firearm handling and proper storage. Remember that any mechanical device can be bypassed with enough time, knowledge, determination and equipment.
LOCKING DEVICES MUST BE USED SAFELY AND RESPONSIBLY
18
Always keep the muzzle pointed in a safe direction and finger off the trigger.
It is important to use the locking device on your Taurus firearm!
Keep the muzzle pointed in a safe direction and your fingers outside the trigger guard at all times during installation of the locking device!
To Install the Factory-Supplied Locking Device:
1. Remove the magazine from your pistol.
2. Open the action completely, and verify that the firearm is completely unloaded and contains no cartridges or cartridge cases! Use the slide stop to keep the action open during installation of the locking device.
3. Insert the cable directly in your pistol as shown in Figure 1.
4. To lock: With the key turned to the farthest clockwise position, insert the loose end of the cable into the lock. Turn the key counterclockwise and remove the key.
5. Once the lock is securely closed, pull firmly on the lock to test the connection and be sure it is locked.
Do not leave or store your firearm with the key in the lock! Store your locked, unloaded firearm and the key in secure, separate locations, away from ammunition, children, and careless adults.
WARNING
Never leave your keys in the lock when the lock is installed on the firearm.
Always keep the muzzle pointed in a safe direction and finger off the trigger.
19
AMMUNITION
WARNING
Using the wrong ammunition in your pistol can result in serious bodily injury and damage to your pistol.
Make certain the ammunition you load in the magazine is the same caliber as is marked on the pistol.
WARNING - AMMUNITION AND INDUSTRY STANDARDS
Use only clean, dry factory-loaded ammunition. Old, damaged, wet or oily ammunition may fire at pressures higher than industry standard, causing injury to you and bystanders or damage to your pistol.
Do not use reloaded ammunition in your pistol. Its firing pressures are unknown and may well exceed industry standard, causing injury to you and bystanders or damage to your pistol.
Odd sounds are signs of trouble. If a round “does not sound right” when it goes off, stop firing right away.
A bullet may be stuck in the barrel. Firing the pistol in this condition may cause pressures higher than industry standard, causing injury to you and bystanders or damage to your pistol.
If you hear any odd sounds when firing your pistol, stop firing, clear the pistol and “field strip” (or disassemble) the pistol in accordance with the procedures listed in this manual. Once the barrel is removed from the slide, look down the bore. If you do not see light, there is something stuck in the bore. Do not fire the pistol again, and take the pistol to a competent gunsmith or contact the Taurus® Service department at 800-327-3776.
WARNING - LEAD EXPOSURE
Discharging firearms in poorly ventilated areas, cleaning firearms or handling ammunition may result in exposure to lead and other substances known to the state of California to cause birth defects, reproductive harm and other serious physical injury. Have adequate ventilation at all times. Wash hands thoroughly after exposure with soap and cold water.
SHOOTING OR CLEANING GUNS MAY EXPOSE YOU TO LEAD
20
Always keep the muzzle pointed in a safe direction and finger off the trigger.
Always keep the muzzle pointed in a safe direction and finger off the trigger.
21
FIREARMS ARE NOT ALL ALIKE
Many makes and models of firearms might LOOK nearly the same. However, they differ widely in design, operation, and in the location and function of various controls. You may access the Taurus website at
TaurusUSA.com to view and print manuals.
“JAMS”
SOMETIMES A CARTRIDGE OR SHELL CASE MAY BECOME “JAMMED” OR STUCK IN THE PISTOL.
TO CLEAR THE JAM, (1) POINT THE MUZZLE IN A SAFE DIRECTION, (2) KEEP YOUR FINGER OFF THE
TRIGGER, (3) REMOVE THE MAGAZINE, THEN (4) PULL BACK THE SLIDE AND LOCK IT TO THE REAR.
THE JAMMED CARTRIDGE OR CASE CAN NOW BE REMOVED BY SHAKING OR PICKING IT OUT.
WARNING - ANY GUN MAY FIRE IF DROPPED
If dropped or struck, the pistol may fire.
WARNING
If dropped or struck the firearm should be inspected by a trained armorer/gunsmith for a complete function check. After the firearm was dropped or struck, mechanisms, including automatic safeties, may not function as intended resulting in accidental death or serious injury.
22
Always keep the muzzle pointed in a safe direction and finger off the trigger.
Always keep the muzzle pointed in a safe direction and finger off the trigger.
23
OPERATING INSTRUCTIONS
1. To remove the magazine press the magazine release button, located near the trigger guard, with your thumb.
1
2
2. To load a magazine hold the bottom of the magazine with one hand and pull down on the
magazine loading button using your thumb. With your other thumb insert the cartridges one at a time, pressing them down and to the rear fully under the lips of the magazine. Repeat until the magazine is loaded to magazine capacity.
3. Insert the magazine into the pistol until it is held by the magazine
catch. If the magazine is not correctly inserted into the pistol, it might fall out when you fire the gun.
3
4
6
24
Always keep the muzzle pointed in a safe direction and finger off the trigger.
4. Hold the pistol with one hand keeping your finger away from the
trigger. With the other hand pull the slide to its limit and release it, so the slide will go forward under recoil spring pressure and will insert one cartridge into the chamber.
5. The pistol is now ready-to-fire by pulling the trigger. After firing, the
slide will recoil from gas pressure, ejecting the empty case and feed another cartridge into the chamber from the magazine. The pistol is now ready to fire again.
6. After the last round is fired, the slide will remain in the open position held by the slide catch.
Always keep the muzzle pointed in a safe direction and finger off the trigger.
25
7
7. If you want to stop shooting before firing the last cartridge of a
magazine, (1) keep your finger off of the trigger, (2) point the
muzzle in a safe direction (3) remove the magazine by pressing the
magazine release button (4) pull the slide to the rear and lock it back and (5) look and feel the magazine well and chamber to confirm the pistol is empty. An empty firearm cannot fire.
WARNING
These Taurus pistols do not have a magazine disconnect (safety). They are capable of firing with magazine removed.
WARNING
If your pistol is equipped with a manual safety, the manual safety lever must be in fully engaged for the manual safety to work.
WARNING
The firearm should never be operated with the manual safety lever between the "on" and "off" positions.
Failure to make certain the manual safety lever is all the way "on" can result in accident, serious bodily injury or even death.
26
Always keep the muzzle pointed in a safe direction and finger off the trigger.
CAUTION
If your pistol is equipped with a manual safety, failure to make sure that the manual safety lever is all the way in the "off" position will result in damage to the pistol.
WARNING - FIRING
The slide opens and shuts quickly while firing. Keep face and hands away from the rear of the slide.
Hot brass is ejected quickly and can burn you. Always wear shooting glasses, hat with brim, and hearing protection.
WARNING - ANY GUN MAY FIRE IF DROPPED
If dropped or struck, the pistol may fire.
Always keep the muzzle pointed in a safe direction and finger off the trigger.
27
DISASSEMBLY
WARNING
Always wear eye protection specified for use with firearms (ANSI Z87.1+) every time you handle your firearm for cleaning and maintenance.
1. Before disassembly always (1) Keep your finger off or the
trigger,
(2) point the muzzle in a safe direction (3) remove the magazine by pressing the
magazine release button (4) pull the slide to the rear and lock it back and (5) look and feel the magazine well and
chamber to confirm the pistol is empty. An empty firearm cannot fire.
2
3
WARNING
After removing the magazine, always check the chamber and make sure it is empty.
2. Hold the pistol in your hand in such a way that four fingers rest over the slide and your thumb rests on the rear of the grip. With the other hand, pull the disassembly latch down. Release the
disassembly latch.
3. Pull and release the
trigger. Push the slide forward 1/2" and lift the slide off the grip.
28
Always keep the muzzle pointed in a safe direction and finger off the trigger.
4
2
5
2
1
1
4. Release the recoil spring assembly from its position on the bottom of the
barrel.
WARNING
Please take care to prevent the forcible ejection of the slide spring assembly plate and compressed slide spring assembly.
5. Remove the barrel from the slide by pulling it to the front and down.
WARNING
No further disassembly is recommended unless done by a qualified gunsmith.
Always keep the muzzle pointed in a safe direction and finger off the trigger.
29
MAGAZINE DISASSEMBLY / ASSEMBLY
1
WARNING
Use care to prevent the forcible ejection of the magazine base retainer and compressed magazine spring.
2
1) To disassemble, use a punch to press in on the magazine
base retainer.
2) Slide the
magazine base cap toward the front of the magazine according to picture 1 and 2.
3) Withdraw the magazine base retainer and magazine spring from magazine tube. Turn the magazine upside down until the
follower is in the lowest position. Push the magazine loading
button out of the follower and remove the follower.
4) Assemble in reverse order.
WARNING
Always wear eye protection that is specified for use with firearms
(ANSI Z87.1+) every time you handle your firearm for cleaning and maintenance.
3
30
Always keep the muzzle pointed in a safe direction and finger off the trigger.
ASSEMBLY
In order to reassemble the pistol, proceed by reversing the disassembly procedure while observing the following details:
1. Insert the barrel in the slide and guide it to the rearmost position.
1
1
2
1
2
2. Insert the recoil spring assembly into the slide over the barrel, compressing the spring slightly to get it into position.
2
3. Line up the slide cut rail openings with the rails on the frame. Gently push the slide down on the frame and then rack the slide back. The disassembly latch will latch back in place on its own.
3
4. You should cycle the
slide several times, with no
magazine inserted and no rounds in the chamber, to insure that the
barrel / slide / frame relationship is correct.
4
Always keep the muzzle pointed in a safe direction and finger off the trigger.
31
SUPPRESSOR ADAPTER COLLAR INSTALLATION
The TX22 pistol comes with a
suppressor adapter collar so that it can be used with a suppressor.
The suppressor adapter collar features an external thread of 1/2-28 which is compatible with the majority of .22LR suppressors available on the market. Use the following directions to install the
suppressor adapter collar.
1. Before installation always (1) keep your finger off the trigger, (2) point the muzzle in a safe direction
(3) remove the magazine by pressing the magazine release button (4) pull the slide to the rear and lock it back and (5) look and feel that the magazine well and chamber to confirm the pistol is empty.
An empty firearm cannot fire.
WARNING
After removing the magazine, always check the chamber and make sure it is empty.
2. Prior to installing the suppressor adapter collar, the barrel thread collar needs to be removed from the barrel.
3. Point the gun away from you. Use a 3/8 inch open ended wrench to turn the barrel thread collar counterclockwise and loosen it from the barrel. Once loosened, remove it from the barrel using your fingers.
4. While keeping the barrel pointed away from you, take the suppressor adapter collar and start gently threading it by hand on the end of the barrel. Once fully threaded on the barrel end, use a 9/16 inch open ended wrench to firmly tighten the suppressor adapter collar.
5. A suppressor of your choice can now be hand tightened to the
suppressor adapter collar. Ensure you only use a suppressor with a 1/2-28 threads. Be careful to install the suppressor properly to prevent damage to the threads on your
suppressor adapter collar.
NOTICE
Only use subsonic or standard velocity ammunition in your pistol when using a suppressor.
32
Always keep the muzzle pointed in a safe direction and finger off the trigger.
REVERSIBLE MAGAZINE RELEASE
The TX22 pistol features a reversible magazine release. It comes configured from the factory for right handed use. To convert the magazine release to left-handed use, follow the procedure below.
1. Before proceeding always (1) keep your finger off the trigger,
(2) point the muzzle in a safe direction (3) remove the magazine by pressing the magazine release button (4) pull the slide to the rear and lock it back and (5) look and feel the magazine well and
chamber to confirm the pistol is empty. An empty firearm cannot fire.
2. Follow direction for disassembly of the pistol on page 28. The
magazine release spring is inside the magazine well. (Fig. 1)
3. While holding the magazine release in place with your fingers, use a flathead screwdriver to slide the magazine release spring out of its groove in the magazine release. (Fig. 2)
4. Remove the magazine release spring from the grip.
5. Remove the magazine release from its slot in the grip.
6. Re-insert the
magazine release reversed inside the grip from the left side of the
grip.
7. Place the magazine release spring back into it's hole in the grip and position the top end of it into the groove of the
magazine release.
1
2
Always keep the muzzle pointed in a safe direction and finger off the trigger.
33
CARE AND MAINTENANCE
Your pistol may be cleaned and lubricated under normal conditions with the disassembly steps described in pages 28-31.
WARNING
In order to keep a firearm safe to use, it must be kept clean and covered with a light film of good quality oil to prevent corrosion. The barrel bore should be cleaned and left free of debris.
Before cleaning, (1) point the muzzle in a safe direction, (2) keep your finger off the trigger,
(3) remove the magazine, then (4) pull back the slide and lock it to the rear, (5) look and feel the magazine well and chamber to confirm the pistol is empty. Never attempt to clean a loaded firearm.
For normal cleaning, rub the pistol with a lightly oiled cloth. In the same way, proceed with the bore of the barrel. Excess oil should be removed.
Dust should be removed from all crevices with a small clean brush.
34
Always keep the muzzle pointed in a safe direction and finger off the trigger.
Always keep the muzzle pointed in a safe direction and finger off the trigger.
35
TX22 COMPETITION OPTICS MOUNTING INSTRUCTIONS
WARNING
Always keep the firearm pointed in a safe direction.
WARNING
Do not attempt to install an optic mount on a loaded firearm.
WARNING
Ensure the firearm is not loaded.
WARNING
Wear safety glasses when removing, installing, or firing your pistol with the red dot optic installed.
The Taurus Competition model comes with 2 adapter plates. The table on page 37 of this manual to select the proper adapter plate for your red dot optic. Plates are marked with dots to identify them.
1. Place the desired adapter plate on the base which is mounted on your TX22 competition barrel.
36
Always keep the muzzle pointed in a safe direction and finger off the trigger.
2. Place your red dot optic over the mounting plate and ensure that the bottom of the sight is properly aligned with its corresponding alignment pins on the mounting plate.
3. Use the screws supplied with your red dot optic.
4.Place a small amount of Loctite 262 on the thread of each screw.
5.Screw in the two screws applying 5.3 in-lbs of torque.
6. Let the Loctite cure for a period of 24 hours before using the firearm.
WARNING
Inspect the mounting screws on the red dot optic before firing. A loose optic can detach upon recoil of the firearm and strike you or a bystander and cause injury. Tighten loose mounting screws before firing.
Sight Model
Trijicon RMR
C-More STS
2
Vortex Venom/Doctor Noblex/Burris Fast Fire/Sightmark Mini
Holosun HS507C
Leupold Delta Point Pro
Plate Designation
Always keep the muzzle pointed in a safe direction and finger off the trigger.
37
TX22 EXPLODED VIEW
40
43
44
58
46
39
37
38
36
57
50
49
35
54
55
54
47
45
42
41
51
52
53
20
12
14
18
13
21
22
15
17
16
8 27
6
12
23
26
9
59
11
10
62
19
24
7
29
4
28
2
25
3
48
56
34
33
31
63
60
61
25
1
5
30
38
Always keep the muzzle pointed in a safe direction and finger off the trigger.
64
65
32
PART LIST
1 GRIP
2 BLOCK, CENTRAL
3 LEVER, TAKEDOWN
4 LEVER, SLIDE CATCH
5 RELEASE, MAGAZINE
6 TRIGGER
7 TRIGGER SHOE
8 BAR, TRIGGER
9 SPRING, TRIGGER SAFETY
10 PIN, TRIGGER
11 PIN, DOWEL
12 PIN, DOWEL
13 HOUSING, FIRE CONTROL
14 BUSHING, SEAR TRIP
15 SEAR
16 SEAR TRIP
17 EJECTOR
18 DISCONNECTER
19 SAFETY, MANUAL LEFT
20 SAFETY, MANUAL RIGHT
21 SPRING, SEAR
22 SPRING, MANUAL SAFETY
23 SPRING, SEAR TRIP
24 PIN, DOWEL
25 PIN, COILED SPRING
26 PIN, COILED SPRING
27 SPRING, TRIGGER BAR
28 SPRING, TAKEDOWN
29 SPRING, SLIDE LOCK
30 SPRING, MAG CATCH
31 BARREL, THREADED
32 COLLAR, BARREL THREAD
33 ROD, RECOIL
34 SLIDE
35 INSERT, IMPACT
36 HOUSING, STRIKER LEFT
37 HOUSING, STRIKER RIGHT
38 STRIKER
39 BLOCK, STRIKER
40 CAP, SLIDE
41 EXTRACTOR
42 PLUNGER, EXTRACTOR
43 RETAINER, SLIDE CAP
44 SPRING, STRIKER
45 SPRING, EXTRACTOR
46 SPRING, STRIKER BLOCK
47 PIN, COILED SPRING
48 FRONT SIGHT
49 SIGHT BASE
50 ADJUSTABLE SIGHT
51 VERTICAL ADJUSTMENT SIGHT SCREW
52 HORIZONTAL ADJUSTMENT SIGHT SCREW
53 ADJUSTMENT SCREW PIN GUIDE
54 BALL BEARING
55 ADJUSTABLE SCREW SPRING
56 SIGHT SCREW
57 PLACEMENT SIGHT SCREW
58 MAGAZINE TUBE
59 FOLLOWER
60 RETAINER, MAGAZINE BASE
61 CAP, MAG BASE
62 BUTTON, MAGAZINE LOADING
63 SPRING, MAGAZINE
64 SPRING, RECOIL
65 COLLAR, SUPPRESSOR ADAPTER
Always keep the muzzle pointed in a safe direction and finger off the trigger.
39
TX22 COMPETITION UPPER EXPLODED VIEW
40
Always keep the muzzle pointed in a safe direction and finger off the trigger.
PART LIST
1 BARREL, THREADED
2 SCREW, 6-32 FLAT HEAD
3 MOUNTING PLATE
4 MOUNTING PLATE
5 MOUNT, RED DOT
6 THREAD PROTECTOR
7 SPRING, RECOIL
8 SLIDE
9 IMPACT INSERT
10 HOUSING, STRIKER LEFT
11 HOUSING, STRIKER RIGHT
12 STRIKER
13 STRIKER BLOCK
14 SLIDE CAP
15 EXTRACTOR
16 EJECTOR PLUNGER
17 SLIDE CAP RETAINER
18 STRIKER SPRING
19 EXTRACTOR SPRING
20 STRIKER BLOCK SPRING
21 PIN, COILED SPRING
22 FRONT SIGHT
23 SIGHT SCREW
24 ASSY, REAR SIGH
25 PLACEMENT SIGHT SCREW
26 ROD, RECOIL
Always keep the muzzle pointed in a safe direction and finger off the trigger.
41
TAURUS SERVICE
Should your firearm require adjustment or repair contact our Customer Care department at 800-327-3776.
Please follow these suggestions to expedite service in the United States to return any firearm to us for adjustment or repair.
1. Federal law permits you to return your firearm to the manufacturer for service via common carriers.
However, state and local firearms laws vary greatly; you should consult your local prosecuting attorney regarding any restrictive laws in your jurisdiction regarding your shipment or receipt of firearms. With the above in mind, it is strongly recommended that any firearm sent to us for repair be sent through a federally licensed dealer.
2. All firearms must be shipped to us prepaid. WE WILL NOT ACCEPT COLLECT SHIPMENTS.
3. Warranty Service: If your product is covered under the Taurus
®
Limited Lifetime Warranty (https:// warranty.taurususa.com ) or was manufactured prior to January 1, 2017, you must contact Taurus to receive warranty service. You may contact Taurus by calling 800-327-3776, logging onto https://taurususa.com, or in writing: Taurus, Attn: Warranty Service, 100 Taurus Way, Bainbridge, GA 39817. Please include a description of the claimed defect, along with your name, address, telephone number, model and serial number of your firearm, proof of purchase, and date of purchase.
4. FIREARMS MUST BE SHIPPED UNLOADED. Double check the chambers of your firearm before shipping. If firearms are sent to Taurus in a loaded condition, we are required by law to notify the
Federal authorities.
5. DO NOT include telescopic sights, custom grips, holsters, or other accessories with any firearm shipped to us.
PARTS
Firearms require periodic maintenance, inspection, adjustment and repair. If your pistol has a malfunction, be safe. Stop firing, “clear” and unload the pistol and take it to a qualified gunsmith. Before shooting it again, contact our Customer Care department if you have any questions.
If water, sand, or other foreign matter gets in your pistol, field strip it (see pages 28-29) and thoroughly clean it. Failure to keep your firearm clean and in proper working order can be dangerous.
Our Customer Care department maintains a full stock of replacement parts for current Taurus firearms.
Even though most gunsmiths have the knowledge, training and ability to make the necessary repairs to your firearm, the skill and workmanship of any particular gunsmith is totally beyond our control. Should your firearm require service, return it to our Customer Care department.
Remember, unauthorized adjustments or parts replacement can void your warranty. If you choose to have someone else do the required work, the purchaser and/or installer of parts must accept full responsibility for the correct adjustment and function of the firearm.
42
Always keep the muzzle pointed in a safe direction and finger off the trigger.
Always keep the muzzle pointed in a safe direction and finger off the trigger.
43
TAURUS
®
LIMITED LIFETIME WARRANTY
Taurus
®
hereby provides the following LIMITED LIFETIME WARRANTY, to the original purchaser of the enclosed Taurus firearm subject to the terms and conditions set forth below.
THIS IS THE ONLY
WARRANTY EXTENDED BY TAURUS COVERING THIS FIREARM.
What does the warranty cover and what is its duration?
Taurus warrants to the original purchaser that the enclosed firearm was made free of defects in material, function, and workmanship. Taurus promises to remedy any defect in material, function or workmanship for the entire time that the original purchaser owns the firearm. This warranty covers the firearm’s finish, grips, magazines, sights or accessories for the first year. Any claims of defect related to lasers must be directed to the manufacturer of the laser. This warranty terminates automatically upon the transfer of this firearm to any individual or entity other than the original purchaser.
44
Always keep the muzzle pointed in a safe direction and finger off the trigger.
Disclaimer and Limitation of Remedy.
ANY IMPLIED WARRANTIES OF MERCHANTABILITY IMPARTED BY STATE LAW WILL BE LIMITED
TO ONE (1) YEAR.
Some States do not allow limitations on how long an implied warranty lasts, so the above-limitation may not apply to you.
ANY AND ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES ARE EXPRESSLY DISCLAIMED
UNDER ALL CIRCUMSTANCES.
Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This LIMITED LIFETIME WARRANTY gives you specific legal rights, and you may also have other rights which vary from State to State.
Taurus will not be responsible for:
1. Defects or malfunctions resulting from careless handling, unauthorized adjustments or modifications.
2. Use of defective or improper ammunition, reloaded ammunition, corrosion, neglect, abuse, ordinary wear and tear or unreasonable use.
3. Criminal misuse, negligence or use under the influence of drugs or alcohol.
How do you obtain warranty service?
The warranty becomes effective only if activated by the original purchaser within thirty (30) days of the purchase date by registering online at: https://warranty.taurususa.com or by calling Taurus at
800-327-3776.
You must contact Taurus to receive warranty service. You may contact Taurus by calling 800-327-3776, logging onto https://taurususa.com, or in writing: Taurus, Attn: Warranty Service, 100 Taurus Way,
Bainbridge, GA 39817. Please include a description of the claimed defect, along with your name, address, telephone number, model and serial number of your firearm, proof of purchase, and date of purchase.
Always keep the muzzle pointed in a safe direction and finger off the trigger.
45
NOTES
46
Always keep the muzzle pointed in a safe direction and finger off the trigger.
Always keep the muzzle pointed in a safe direction and finger off the trigger.
47
IMPORTANT
DO NOT DISCARD
KEEP THIS MANUAL WITH THE FIREARM
UPON CHANGE OF OWNERSHIP.
TAURUS INTERNATIONAL
MANUFACTURING, INC.
100 Taurus Way
Bainbridge, GA 39817
Telephone: 1-800-327-3776
TAURUSUSA.COM
045-0031-00 Rev. 1
Pobierz
Publiczny link zaktualizowany
Publiczny link do Twojego czatu został zaktualizowany. You may view and manage your chat links after registration here.
Publiczny link do dokumentu
Reklama
