advertisement
BASE UNIT
800 2/3 Drawer
Assembly Guide
800
2 Drawer
800
3 Drawer
For Internal Use: FI.WR.INS.026_WKIN00108_BASE_800_2_3Drawer_Rev3.indd
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
Standard Drawer (Packed Separately)
Fitting Pack Contents
Metal Back Panel
x 1
(J) x16
Drawer Runner
16mm Screws
(Q) x4
21mm
Screw
(N) x1
Door Buffer
Drawer
Front
Fixing
x 2
Drawer
Base
x 1
Drawer
Cover Cap
x2
Drawer Runner
x 1 Left Hand
Frontal
(Supplied Separately
Drawer Runner
x 1 Right Hand
Drawer Side
x1 Right Hand
Drawer Side
x1 Left Hand
DEEP Drawer (Packed Separately)
Fitting Pack Contents
METAL BACK PANEL
x 1
Gallery
Rail
x 2
(Y) x2
Gallery
Head
(J) x16
Drawer Runner
16mm Screws
(Q) x4
21mm
Screw
(L) x2
15mm
Screw
(N) x1
Door Buffer
Drawer
Front
Fixing
x 2
Drawer
Cover Cap
x2
Drawer
Base
x 1
Drawer Runner
x 1 Left Hand
Frontal
(Supplied separately)
Drawer Runner
x 1 Right Hand
Drawer Side
x1 Right Hand
Drawer Side
x1 Left Hand
REQUIRED TOOLS
Page 1
NOT to be used with CAM DOWEL
& CAM LOCK
For Internal Use: FI.WR.INS.026_WKIN00108_BASE_800_2_3Drawer_Rev3.indd
Step 1.
Secure drawer base to drawer side using 4 x 16mm drawer runner screws
(J)
in holes provided.
Seat the edge of drawer base tight into corner of casing, as shown.
Decorative face
The decorative face of drawer base to be positioned as shown.
Repeat step 1
so both drawer sides are attached to drawer base.
Drawer base
Front of drawer
Step 2.
Clip on metal back panel to drawer base
& drawer sides.
J
Drawer base
J
J
J
J
Step 4.
Frontal Attachment
Secure drawer side fixing clips using 2 x 21mm screws (S) in pilot holes provided as shown.
J
J
Fixing clip
J
Step 3.
J
Screw back panel in position using 2 x 16mm screws
(J)
to drawer base in holes provided.
Standard Drawer
Assembly
View from back
Metal back panel
Drawer base
white decorative face up
Fixing clip
& (Q)
99mm
67mm
Standard drawer
99mm
67mm
J
J
Fixing clip
& (Q)
Metal back panel
Drawer Frontal Adjustment
Step 5.
Draw Adjustment
Screw point
1
as shown to adjust drawer frontal right & left.
Screw point
2a
as shown to adjust drawer frontal up & down.
1
Drawer frontal
3
2a
2b
Tighten
2b
once in position.
Releasing fixing clip. Screw point
3
whilst applying downward pressure as shown to release.
View on side of drawer side
For Internal Use: FI.WR.INS.026_WKIN00108_BASE_800_2_3Drawer_Rev3.indd
Drawer
Cover Cap
Q
Q
Drawer side fixing clip
J
Drawer side
Drawer frontal
Step 6.
Fit Drawer Cover Caps
over drawer side adjustment.
Page 2
Deep Drawer
Assembly
Step 1.
Secure drawer base to drawer side using 4 x 16mm drawer runner screws
(J)
in holes provided.
Seat the edge of drawerbase tight into corner ofcasing, as shown.
Decorative face
The decorative face of drawer base to be positioned as shown.
Drawer base
Drawer base
J
J
J
J
J
J
J
J
Step 3.
Screw back panel in position using
2 x 16mm screws
(J)
to drawer base in holes provided.
Repeat step 1
so both drawer sides are attached to drawer base.
View from back
Metal back panel
Front of drawer
Step 2.
Clip on metal back panel to drawer base
& drawer sides.
J
J
Metal back panel
Drawer base
white decorative face up
Y & L
Fixing clip
& (Q)
231mm
99mm
67mm
Deep drawer
231mm
99mm
67mm
Y & L
Fixing clip
& (Q)
J
Drawer Frontal
Step 5.
Adjustment
Draw Adjustment
Screw point
1
as shown to adjust drawer frontal right & left.
Step 4.
Frontal Attachment
Secure
drawer side fixing clips
using 2 x 21mm
screws (Q)
in pilot holes provided as shown.
Fixing clip
Drawer frontal
Drawer side fixing clip
Drawer frontal
Q
Q
Drawer side
Screw point
2a
as shown to adjust drawer frontal up & down.
2
Step 6.
Fit Gallery Rail into the top corners of Metal
BackPanel.
Locate front end of the
Gallery Rail into the
Tighten
2b
once in position.
Releasing fixing clip.
Screw point
3
whilst applying downward pressure as shown to release.
Page 3
1
opening of the gallery
Head, which is secured to the frontal as shown
Step 7.
Fit Drawer Cover Caps
View on side of drawer side Drawer
Cover Cap
over drawer side adjustment.
For Internal Use: FI.WR.INS.026_WKIN00108_BASE_800_2_3Drawer_Rev3.indd
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
BASE UNIT
800 2/3 Drawer
Carcass Assembly
Panel A
x1 Back Panel
Panel B
x2 End Panel
Panel E
x2 Rail Panel
Panel C
x1 Base Panel
(F) x12
Wooden Dowel
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x7
30mm
Screw
(L) x30
15mm
Screw
REQUIRED TOOLS
NOT to be used with CAM DOWEL
& CAM LOCK
For Internal Use: FI.WR.INS.026_WKIN00108_BASE_800_2_3Drawer_Rev3.indd
L Bracket x2 Space Plug x2
Page 4
BASE UNIT
800 2/3 Drawer
Carcass Assembly
2 drawer
Drawer runner bracket screw position
J
J
37mm
261mm
B
431mm
J
J
B
74mm
from base
646mm
Step 1.
To attach drawer runner screw into end panels
(B)
using 2 x 16mm screws
(J)
per drawer rail, into pilot holes provided,
3rd hole from front, as shown.
360mm
3 drawer
Page 5
4 drawer
74mm
from base
646mm
503mm
360mm
B
74mm
from base
For Internal Use: FI.WR.INS.026_WKIN00108_BASE_800_2_3Drawer_Rev3.indd
Seat (G) cam dowel into hole as shown
.
Step 2.
Seat dowel
(F)
into holes in panels as shown.
BASE UNIT
800 2/3 Drawer
Carcass Assembly
Step 3.
Seat cam dowel
(G)
into holes in panels as shown.
E
B
G F F
F F G
G
F
E
B B
B
C
G F F
G
G
Dowel (F)
& Cam Dowel (G) location detail
F
F G
Step 4.
Attach panels
(C)
&
(E)
to panels
(B)
, using cam dowel
(G)
& cam lock
(H)
(in blue
), and also using dowels
(F)
(in orange
) in positions as shown.
NB. All
Cam Locks (H)
are to be positioned facing the outside of the unit carcass, for ease of tightening.
Do
not
use power tools with cam dowel
(G)
or cam lock
(H)
C
G
G
View from underside
B
H
C
H
View from underside
B
Step 5.
Cam Lock
(H)
Join panels
(C)
&
(E)
to
(B)
.
Insert cam lock
(H)
.
Do NOT tighten until Step 7.
For Internal Use: FI.WR.INS.026_WKIN00108_BASE_800_2_3Drawer_Rev3.indd
Page 6
BASE UNIT
800 2/3 Drawer
Carcass Assembly
B
E
A
C
B
Page 7
Step 6.
Slide back panel
(A)
into groove of end panels
(B)
.
Once back panel
(A)
is in position, ensure the panel is flush & square with bottom of end panels
(B)
.
Step 7.
Hand tighten all cam locks
(H)
, this will expand cam dowels
(G)
and tighten the unit together.
Step 8.
Ensure carcass is square. Secure back panel
(A)
with 4 x 30mm screws
(K)
equally spaced at the bottom of back panel
(A)
into base panel
(C)
, as shown.
Ensure you screw into the centre of base panel
(C)
(9mm from bottom edge).
B
C
9mm
K
K
K
K
A
E
For Internal Use: FI.WR.INS.026_WKIN00108_BASE_800_2_3Drawer_Rev3.indd
B
C
Leg position diagram
B
Front
Front
Step 9.
Secure each of the legs into place with
2 x 15mmscrews
(L)
per leg
Ensure legs are rotated as shown so that part of it is supporting the end panels
(B)
.
Front legs should have flat edge to the front.
BASE UNIT
800 2/3 Drawer
Carcass Assembly
L
L
Step 10.
Lightly hit centre peg of leg base with hammer until flush with the leg base.
C
C
B
B
Step 11.
Push leg firmly down into leg base.
Adjust legs to 155mm before turning carcass upright. Once in situ level accordingly.
C
B
For Internal Use: FI.WR.INS.026_WKIN00108_BASE_800_2_3Drawer_Rev3.indd
Page 8
BASE UNIT
800 2/3 Drawer
Carcass Assembly
K
Secure unit to wall using
space plug
.
Drill pilot hole through the back brace into the wall and insert wall plug. Then unwind space plug until it contacts both surfaces.
Finally, tighten the screw.
Screws for attaching to walls are not provided as these vary depending on your wall material and construction. Ensure appropriate fixings for wall construction are used.
Securing to Adjacent Units
Screw into any side units using the 30mm screws
(K)
provided to secure to unit. Screw just to the rear, at the top and bottom of both sides
of the unit, place a cover cap on the head to conceal it.
J
J
L Brackets
Use 2 x 15mm screws
(J)
to secure each of the L brackets to the cabinets at either side.
Then screw up through into the worktop as shown.
Screws for attaching to worktop are not supplied as these vary depending on worktop material and thickness. Ensure appropriate fixings for attaching worktop are used. L brackets should only be fitted for securing wood and laminate worktops, please refer to the specialist worktop supplier if these are required for solid surface worktops.
Page 9
Worktop
Screw up through the front rail into your worktop to secure it in place.
Screws for attaching to worktop are not supplied as these vary depending on worktop material and thickness. Ensure appropriate fixings for attaching worktop are used. Please refer to the specialist worktop supplier if these are required for solid surface worktops.
For Internal Use: FI.WR.INS.026_WKIN00108_BASE_800_2_3Drawer_Rev3.indd
advertisement
Related manuals
advertisement