Ricoh MP C2504 series is a high-performance multifunction printer that offers a wide range of features to meet the needs of demanding office environments. It can print, copy, scan, and fax documents at speeds of up to 25 pages per minute, and it has a maximum paper capacity of 2,300 sheets. The MP C2504 series also features a user-friendly control panel and a variety of advanced finishing options, making it an ideal choice for businesses that need a reliable and versatile multifunction printer.
Advertisement
Advertisement
MP C2004 / C2504
Machine Code:
D243 / D244
Field Service Manual
July, 2016
In this manual, the following important symbols and notations are used.
• A Warning indicates a potentially hazardous situation. Failure to obey a Warning could result in death or serious injury.
• A Caution indicates a potentially hazardous situation. Failure to obey a Caution could result in minor or moderate injury or damage to the machine or other property.
• Obey these guidelines to avoid problems such as misfeeds, damage to originals, loss of valuable data and to prevent damage to the machine.
• This information provides tips and advice about how to best service the machine.
For your safety, please read this manual carefully before you use this product. Keep this manual handy for future reference.
Safety Information
Always obey the following safety precautions when using this product.
Safety During Operation
In this manual, the following important symbols and notations are used.
[A]: ON
[B]: OFF
[C]: Push ON/Push OFF
[D]: Standby
Switches and Symbols
Where symbols are used on or near switches on machines for Europe and other areas, the meaning of each symbol conforms with IEC60417.
1. Before disassembling or assembling parts of the machine and peripherals, make sure that the machine and peripheral power cords are unplugged.
2. The plug should be near the machine and easily accessible.
3. Note that some components of the machine and the paper tray unit are supplied with electrical voltage even if the main power switch is turned off.
4. Always unplug the power cord from the power source before you move the product. Before you move the machine, arrange the power cord so it will not fall under the machine.
5. Disconnect all peripheral units (finisher, LCT, etc.) from the mainframe before you move the machine.
6. If any adjustment or operation check has to be made with exterior covers off or open while the main switch is turned on, keep hands away from electrified or mechanically driven components.
7. The machine drives some of its components when it completes the warm-up period. Be careful to keep hands away from the mechanical and electrical components as the machine starts operation.
8. The inside and the metal parts of the fusing unit become extremely hot while the machine is operating. Be careful to avoid touching those components with your bare hands.
9. To prevent a fire or explosion, keep the machine away from flammable liquids, gases, and aerosols.
10. Do not use flammable sprays or solvent in the vicinity of the machine. Also, avoid placing these items in the vicinity of the machine. Doing so could result in fire or electric shock.
11. To avoid fire or explosion, never use an organic cleaner near any part that generates heat.
12. Clean the floor completely after accidental spillage of silicone oil or other materials to prevent slippery surfaces that could cause accidents leading to hand or leg injuries.
13. Never remove any safety device unless it requires replacement. Always replace safety devices immediately.
14. Never do any procedure that defeats the function of any safety device.
15. Modification or removal of a safety device (fuse, switch, etc.) could lead to a fire and personal injury. Always test the operation of the machine to ensure that it is operating normally and safely after removal and replacement of any safety device.
16. For replacements use only the correct fuses or circuit breakers rated for use with the machine. Using replacement devices not designed for use with the machine could lead to a fire and personal injuries.
17. For machines installed with the ADF/ARDF:
When a thick book or three-dimensional original is placed on the exposure glass and the ARDF cover is lowered, the back side of the ARDF rises up to accommodate the original. Therefore, when closing the ARDF, please be sure to keep your hands away from the hinges at the back of the
ARDF.
18. When using a vacuum cleaner around the machine, keep others away from the cleaner, especially small children.
19. For machines installed with the anti-tip components:
The anti-tip components are necessary for meeting the requirements of IEC60950-1, the international standard for safety. The aim of these components is to prevent the products, which are heavy in weight, from toppling as a result of people running into or leaning onto the products, which can lead to serious accidents such as persons becoming trapped under the product. (U.S.:
UL60950-1, Europe: EN60950-1) Therefore, removal of such components must always be with the consent of the customer. Do not remove them at your own judgment.
1. For the machines installed with the ozone filters:
• Never operate the machine without the ozone filters installed.
• Always replace the ozone filters with the specified types at the proper intervals.
2. The machine, which use high voltage power source, can generate ozone gas. High ozone density is harmful to human health. Therefore, locate the machine in a large well ventilated room that has an air turnover rate of more than 50m
3
/hr/person.
3. Toner and developer are non-toxic, but if you get either of them in your eyes by accident, it may cause temporary eye discomfort. Try to remove with eye drops or flush with water as first aid. If unsuccessful, get medical attention.
1. The machine and its peripherals must be installed and maintained by a customer service representative who has completed the training course on those models with exceptions on some machines where the installation can be handled by the user.
1. Do not incinerate toner bottles or used toner. Toner dust may ignite suddenly when exposed to an open flame.
2. Dispose of used toner, developer, organic photoconductors, and AIO unit in accordance with local regulations. (These are non-toxic supplies.)
3. Dispose of replaced parts in accordance with local regulations.
4. When keeping used lithium batteries in order to dispose of them later, do not put more than 100 batteries per sealed box. Storing larger numbers or not sealing them apart may lead to chemical reactions and heat build-up.
5. The danger of explosion exists if a battery of this type is incorrectly replaced. Replace only with the same or an equivalent type recommended by the manufacturer. Discard used batteries in accordance with the manufacturer’s instructions.
• Work carefully when removing paper jams or replacing toner bottles or cartridges to avoid spilling toner on clothing or the hands.
• If toner is inhaled, immediately gargle with large amounts of cold water and move to a wellventilated location. If there are signs of irritation or other problems, seek medical attention.
• If toner gets on the skin, wash immediately with soap and cold running water.
• If toner gets into the eyes, flush the eyes with cold running water or eye wash. If there are signs of irritation or other problems, seek medical attention.
• If toner is swallowed, drink a large amount of cold water to dilute the ingested toner. If there are signs of any problem, seek medical attention.
• If toner spills on clothing, wash the affected area immediately with soap and cold water. Never use hot water! Hot water can cause toner to set and permanently stain fabric.
• Always store toner and developer supplies such as toner and developer packages, cartridges, bottles (including used toner and empty bottles and cartridges), and AIO unit out of the reach of children.
• Always store fresh toner supplies or empty bottles or cartridges in a cool, dry location that is not exposed to direct sunlight.
• Do not use a vacuum cleaner to remove spilled toner (including used toner). Vacuumed toner may cause a fire or explosion due to sparks or electrical contact inside the cleaner. However, it is possible to use a cleaner designed to be dust explosion-proof. If toner is spilled over the floor, sweep up spilled toner slowly and clean up any remaining toner with a wet cloth.
For the machines installed the development cooling system:
1. The development unit cooling system circulates propylene glycol from a sealed tank through hoses that pass behind cooling plates on the sides of each development unit.
2. The coolant tank is located at the bottom of the cooling box on the back of the main machine.
3. Always obey local laws and regulations if you need to dispose of a tank or the propylene glycol coolant.
4. The tank must never be emptied directly into a local drainage system, river, pond, or lake.
5. Contact a professional industrial waste disposal organization and ask them to dispose of the tank.
The Center for Devices and Radiological Health (CDRH) prohibits the repair of laser-based optical units in the field. The optical housing unit can only be repaired in a factory or at a location with the requisite equipment. The laser subsystem is replaceable in the field by a qualified Customer Engineer. The laser chassis is not repairable in the field. Customer engineers are therefore directed to return all chassis and laser subsystems to the factory or service depot when replacement of the optical subsystem is required.
• Use of controls, or adjustment, or performance of procedures other than those specified in this manual may result in hazardous radiation exposure.
WARNING FOR LASER UNIT
WARNING:
Turn off the main switch before attempting any of the procedures in the Laser Unit section. Laser beams can seriously damage your eyes.
The color controller uses a double pole fuse. If this fuse blows, be sure to replace it with an identical fuse.
1. Always replace a battery with the same type of battery prescribed for use with the color controller unit. Replacing a battery with any type other than the one prescribed for use could cause an explosion.
2. Never discard used batteries by mixing them with other batteries or other refuse.
3. Always remove used batteries from the work site and dispose of them in accordance with local laws and regulations regarding the disposal of such items.
This manual uses several symbols and abbreviations. The meaning of those symbols and abbreviations are as follows:
Symbol What it means
Clip ring
Screw
Connector
Clamp
SEF
LEF
K
C
M
Y
B/W, BW
FC
E-ring
Flat flexible cable
Timing belt
Short edge feed [A]
Long edge feed [B]
Black
Cyan
Magenta
Yellow
Black and white
Full color
1
2
Adobe, Acrobat, PageMaker, PostScript, and PostScript 3 are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Ricoh Company, Ltd. is under license.
Firefox and Thunderbird are registered trademarks of the Mozilla Foundation.
Google, Android, and Chrome are trademarks of Google Inc.
iOS® is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the United
States and certain other countries.
Java is a registered trademark of Oracle and/or its affiliates.
JAWS® is a registered trademark of Freedom Scientific, Inc., St. Petersburg, Florida and/or other countries.
Kerberos is a trademark of the Massachusetts Institute of Technology (MIT).
Linux is a registered trademark of Linus Torvalds.
Macintosh, OS X, Bonjour, Safari, and TrueType are trademarks of Apple Inc., registered in the U.S.
and other countries.
Microsoft, Windows, Windows Server, Windows Vista, Internet Explorer, and Outlook are either registered trademarks or trademarks of Microsoft Corp. in the United States and/or other countries.
PictBridge is a trademark.
QR Code is a registered trademark of DENSO WAVE INCORPORATED in Japan and in other countries.
"Red Hat" is a registered trademark of Red Hat, Inc.
The SD and SD logo are trademarks of SD-3C, LLC.
UNIX is a registered trademark of The Open Group.
UPnP is a trademark of UPnP Implementers Corporation.
This product includes RSA BSAFE® Cryptographic software of EMC Corporation. RSA and BSAFE are registered trademarks or trademarks of EMC Corporation in the United States and other countries.
The proper names of Internet Explorer 6, 7, and 8 are as follows:
• Microsoft® Internet Explorer® 6
• Windows® Internet Explorer® 7
• Windows® Internet Explorer® 8
The proper names of the Windows operating systems are as follows:
• The product names of Windows Vista are as follows:
Microsoft® Windows Vista® Ultimate
Microsoft® Windows Vista® Business
Microsoft® Windows Vista® Home Premium
Microsoft® Windows Vista® Home Basic
Microsoft® Windows Vista® Enterprise
• The product names of Windows 7 are as follows:
Microsoft® Windows® 7 Home Premium
Microsoft® Windows® 7 Professional
Microsoft® Windows® 7 Ultimate
Microsoft® Windows® 7 Enterprise
• The product names of Windows 8 are as follows:
Microsoft® Windows® 8
Microsoft® Windows® 8 Pro
Microsoft® Windows® 8 Enterprise
• The product names of Windows 8.1 are as follows:
Microsoft® Windows® 8.1
Microsoft® Windows® 8.1 Pro
Microsoft® Windows® 8.1 Enterprise
• The product names of Windows 10 are as follows:
3
4
Microsoft® Windows® 10 Home Premium
Microsoft® Windows® 10 Pro
Microsoft® Windows® 10 Enterprise
Microsoft® Windows® 10 Education
• The product names of Windows Server 2003 are as follows:
Microsoft® Windows Server® 2003 Standard Edition
Microsoft® Windows Server® 2003 Enterprise Edition
• The product names of Windows Server 2003 R2 are as follows:
Microsoft® Windows Server® 2003 R2 Standard Edition
Microsoft® Windows Server® 2003 R2 Enterprise Edition
• The product names of Windows Server 2008 are as follows:
Microsoft® Windows Server® 2008 Standard
Microsoft® Windows Server® 2008 Enterprise
• The product names of Windows Server 2008 R2 are as follows:
Microsoft® Windows Server® 2008 R2 Standard
Microsoft® Windows Server® 2008 R2 Enterprise
• The product names of Windows Server 2012 are as follows:
Microsoft® Windows Server® 2012 Foundation
Microsoft® Windows Server® 2012 Essentials
Microsoft® Windows Server® 2012 Standard
• The product names of Windows Server 2012 R2 are as follows:
Microsoft® Windows Server® 2012 R2 Foundation
Microsoft® Windows Server® 2012 R2 Essentials
Microsoft® Windows Server® 2012 R2 Standard
Other product names used herein are for identification purposes only and might be trademarks of their respective companies. We disclaim any and all rights to those marks.
Microsoft product screen shots reprinted with permission from Microsoft Corporation.
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
When SC544-02, SC554-02 (Non-contact Thermistor High Temperature Detection) Is Displayed......
23
24
No waste toner bottle set is displayed on controller board even when it is clear that is set....1040
25
26
Maximum number of sheets for stapling and what happens when the job has too many pages....1054
Behavior: When the number of sheets exceeds the maximum staple capability...................... 1055
Select the behavior when the job has more than the maximum of staple capability with SP5199..
Misjudgment for Auto Color Selection (e.g. When Using Paper Which Has a Strong Blue Component)
27
28
Improved Tolerance to Black Lines When Paper Passes through ARDF/SPDF........................ 1106
Difference between Non-contact Transport and Contact Transport in DF Scanning...............1109
29
30
31
32
MSENS1 (Proximity Sensor (Human Detection Sensor), MSENS2 (Proximity Sensor (Human
33
34
• For details about electrical components layout, refer to page 1086 "Component Layout".
35
1. Product Information
36
No.
1 Scanner Unit
2 Paper Exit Unit
Description
3 Fusing Unit
4 Paper Transfer Unit
5 Duplex Unit
No.
Description
6 Paper Feed Unit
7 Waste Toner Unit
8 Laser Exposure Unit
9 PCDU
10 Image Transfer Unit
Product Overview
No.
1 SPDF DF3100
Description
2 Bridge Unit BU3070
No.
Description
3 Booklet Finisher SR3220
4 Paper Feed Unit PB3220/PB3210
37
1. Product Information
38
No.
Description
1 ARDF DF3090
2 Internal Finisher SR3130
No.
Description
3 Paper Feed Unit PB3220/PB3210
Product Overview
No.
Description
1 Platen Cover PN2000
2 Paper Feed Unit PB3150
3 Caster Table Type M3
No.
Description
4 Side Tray Type M3
5 1 Bin Tray BN3110
39
1. Product Information
40
No.
Description
1 Paper feed motor
2 Duplex/ Bypass motor
3 Transport motor
4 Registration motor
No.
Description
12 Toner bottle drive motor (M)
13 Toner bottle drive motor (Y)
14 Scanner motor
15 Toner supply motor (Y)
Product Overview
No.
Description
5 Paper transfer contact and release motor
6 Fusing motor
7 Paper exit /Pressure release motor
8 Duplex entrance motor
9 Reverse motor
10 Toner bottle drive motor (Bk)
11 Toner bottle drive motor (C)
No.
Description
16 Toner supply motor (M)
17 Toner supply motor (C)
18 Toner supply motor (Bk)
19 Development motor: CMY
20 PCU Motor: CMY
21 Development solenoid
22 PCU: Black/ Image transfer motor
41
42
1. Product Information
-22
-26
-27
-29
-17
-18
-19
-21
-29
-65
Key Area
North America/ Central, South America
North America GSA models
Taiwan
China
China
Korea Narajanta model
Europe/ Middle, Near East
Korea
Asia/Pacific/ Central, South America
Europe/ Middle, Near East
Power
120V/60Hz
120V/60Hz
110V/60Hz
220-240V/50-60Hz
220-240V/50-60Hz
220V/60Hz
220-240V/50-60Hz
220V/60Hz
220-240V/50-60Hz
220-240V/50-60Hz
Machine Code
D243
D244
Product Name
MP C2004SP
MP C2504SP
Machine Code
D243 GSA
D244 GSA
Product Name
MP C2004SPG
MP C2504SPG
DF
ARDF 3090 Std.
CPM
FC: 20cpm/BW: 20cpm
FC: 25cpm/BW: 25cpm
DF
ARDF 3090 Std.
CPM
FC: 20cpm/BW: 20cpm
FC: 25cpm/BW: 25cpm
Machine Codes and Peripherals Configuration
Machine Code
D243
D244
Product Name
MP C2004SP
MP C2504SP
Machine Code
D243
D244
Product Name
MP C2004SP
MP C2504SP
Machine Code
D243
D244
Product Name
DSc1220
DSc1225
Machine Code
D243
D244
Product Name
MP C2094SPJ
MP C2594SPJ
Machine Code
D243
D244
Product Name
MP C2004SP
MP C2504SP
DF
ARDF 3090 Std.
CPM
FC: 20cpm/BW: 20cpm
FC: 25cpm/BW: 25cpm
None
DF
None
DF
None
DF
CPM
FC: 20cpm/BW: 20cpm
FC: 25cpm/BW: 25cpm
CPM
FC: 20cpm/BW: 20cpm
FC: 25cpm/BW: 25cpm
CPM
FC: 20cpm/BW: 20cpm
FC: 25cpm/BW: 25cpm
DF
ARDF 3090 Std.
CPM
FC: 20cpm/BW: 20cpm
FC: 25cpm/BW: 25cpm
43
44
1. Product Information
Machine Code
D243
D244
Product Name
MP C2004SP
MP C2504SP
Machine Code
D243
D244
Product Name
MP C2004ASP
MP C2504ASP
None
DF CPM
FC: 20cpm/BW: 20cpm
FC: 25cpm/BW: 25cpm
DF
SPDF 3100 Std.
CPM
FC: 20cpm/BW: 20cpm
FC: 25cpm/BW: 25cpm
Product Name
SPDF DF3100
Booklet Finisher SR3220
1 Bin Tray BN3110
Bridge Unit BU3070
Internal Finisher SR3130
Side Tray Type M3
Internal Finisher SR3180
Banner Paper Guide Tray Type
M19
IEEE 802.11a/g/n Interface
Unit Type M19
Memory Unit Type M19 4GB
Extended USB Board Type
M19
Code EU NA
D3B0 N/A N/A
D3B9 -17 -17
D3CQ -17
D685 -18
D690
D725
-18
-18
D766
D3BF
-18
-00
-18
-00
-17
-18
-18
-18
D3BR
D3BX
D3BS
-01
-03
-01
-01
-03
-01
-17
-18
-18
-18
AA
-17
-17
-18
-00
-17
-18
-18
-18
KOR TWN CHN
-17
-17
-17
-17
-21
-21
-18
-00
-17
-18
-18
-18
-18
-00
-22
-00
-21
-22
-22
-22
-01 N/A N/A N/A
-03
-01
-03
-01
-03
-01
-03
-01
Machine Codes and Peripherals Configuration
Product Name
IEEE 1284 Interface Board
Type M19
XPS Direct Print Option Type
M19
USB Device Server Option
Type M19
Code
D3C0
D3BC
D3BC
PostScript3 Unit Type M19
Camera Direct Print Card Type
M19
File Format Converter Type
M19
DataOverwriteSecurity Unit
Type M19
Fax Option Type M19
D3BD
D3BD
D3BR
D3BS
G3 Interface Unit Type M19
Fax Memory Unit Type M19
64MB
D3BV
D3BV
D3BZ
Fax Connection Unit Type M19 D3BD
D3BS
D3BS
NFC Card Reader Type M19
Smart Card Reader Built-in Unit
Type M19
Imageable Area Extension Unit
Type M19
External Keyboard Bracket
Type M19
Punch Unit PU3050 NA
Punch Unit PU3050 EU
D3BR
D3BR
Punch Unit PU3050 SC
Punch Unit PU3040 NA
D717
D717
D717
D716
EU
-17
-24
-28
-05
-13
-04
-03
-01
-21
-22
-01
-07
-17
-07
-10
-17
-27
-28
-17
-04
-03
-02
-08
-17
-02
-21
-22
-07
-10
NA
-17
-25
-29
06
-13
-17
-27
-28
-17
AA
-17
KOR TWN CHN
-17 -17 -17
-26 -26 -26 -26
-29 -29 N/A N/A
-07
-13
-07
-13
-07
-13
-07
-13
-04
-03
-03
-08
-17
-03
-21
-22
-07
-10
-04
-03
-03
-08
-17
-03
-21
-22
-07
-10
-04
-03
-04
12
-17
-03
-21
-22
-07
-10
-04
-03
-05
-08
-17
-03
-21
-22
-07
-10
-17
-27
-28
-17
-17
-27
-28
-17
-17
-27
-28
-17
N/A
-21
N/A
N/A
45
46
1. Product Information
Product Name
Punch Unit PU3040 EU
Punch Unit PU3040 SC
Paper Feed Unit PB3150
Paper Feed Unit PB3220
Paper Feed Unit PB3210
Caster Table Type M3
Code
D716
D716
EU
-27
-28
D694
D787
-17
-18
D787 N/A
D178 -02
Internal Shift Tray SH3070
Platen Cover PN2000
ARDF DF3090
Handset HS3020
Marker Type 30
ADF Handle Type C
RICOH e-Sharing Box
SD Card for Fonts Type D
Unicode Font Package for
SAP(R) 1 License
Unicode Font Package for
SAP(R) 10 License
Unicode Font Package for
SAP(R) 100 License
B869
B869
Optional Counter Interface
Unit Type M12
B870
Key Counter Bracket Type M3 D739
Card Reader Bracket Type
3352
D593
Bluetooth Interface Unit Type D D566
D691 -17 -17
D700 N/A N/A
D779 N/A N/A
D739 -17 N/A
H903
D593
-02
-81
D668 -01
D641 N/A
B869 -01
-02
-03
-21
-09
-61
-01
-02
-03
-21
-09
-61
-01
-02
-81
-02
-54
-01
NA
-27
-28
-17
N/A
-17
-02
AA
-27
-28
KOR TWN CHN
-27
-28
-27
-28
-21
N/A
-17
-18
-17
-18
-17
-18
-21
-22
N/A N/A N/A N/A
-02 -02 -02 -02
-17
-01
-17
-01
-17
N/A
-21
-01
-17 -17 -17 -21
N/A N/A N/A N/A
-02
-81
N/A -02
-81 -81
N/A
-81
-03 -03 -03 -04
N/A N/A N/A N/A
-01 -01 -01 -01
-02
-03
-21
-09
-61
-01
-02
-03
-21
-09
-61
N/A
-02
-03
-21
-09
-61
N/A
-02
-03
-21
-09
-61
N/A
Machine Codes and Peripherals Configuration
Product Name
Enhanced Security HDD Option
Type M12
OCR Unit Type M13
Code
D3A6
D3AC
EU
-02
-23
NA
-02
AA KOR TWN CHN
N/A N/A N/A N/A
-24 -25 -25 -25 -25
No.
Item
1 Banner Paper Guide Tray Type
M19
2 Paper Feed Unit PB3150
3 Caster Table Type M3
D3BF-00
Code
D694-17, -21
D178-02
Remarks
Common (D238/D239/D240/
D241/D242)
47
48
1. Product Information
No.
Item
4 Paper Feed Unit PB3210 (EU)
Paper Feed Unit PB3220 (NA,
Asia, KOR, TWN, CHN)
5 1 Bin Tray BN3110
6 Bridge Unit BU3070
7 Internal Shift Tray SH3070
8 Side Tray Type M3
9 Internal Finisher SR3130
10 Internal Finisher SR3180
11 Booklet Finisher SR3220
Punch Unit PU3050 NA
Punch Unit PU3050 EU
Punch Unit PU3050 SC
Punch Unit PU3040 NA
Punch Unit PU3040 EU
Punch Unit PU3040 SC
Platen Cover PN2000
ARDF DF3090
SPDF DF3100
Code
D787-17
D787-18, -22
D3CQ-17, -21
D685-18, -22
D691-17, -21
D725-18, -22
D690-18, -22
D766-18, -22
D3B9-17, -21
D717-17
D717-27, -21
D717-28
D716-17
D716-27, -21
D716-28
D700-01
D779-17, -21
D3B0-17, -21
Remarks
Common
(D176/D177/D237)
Common (D238/D239/D240/
D241/D242)
Common (D238/D239/D240/
D241/D242)
See "Appendices" for the following information:
• Machine Specifications
• Software Accessories
• Supported Paper Sizes
• Option Specifications
Specifications
49
50
1. Product Information
Temperature Range:
Humidity Range:
Ambient Illumination:
Ventilation:
10°C to 32°C (50°F to 90°F)
15% to 80% RH
Less than 1,500 lux (do not expose to direct sunlight.)
Room air should turn over at least 30 m
3
/hr/person
51
52
2. Installation
1. Avoid areas exposed to sudden temperature changes:
1) Areas directly exposed to cool air from an air conditioner.
2) Areas directly exposed to heat from a heater.
2. Do not place the machine where it will be exposed to corrosive gases.
3. Do not install the machine at any location over 2,000 m (6,500 ft.) above sea level. (NA model can be installed up to 2,500m (8,202 ft.))
4. Place the main machine on a strong and level base. Inclination on any side should be no more than 5 mm (0.2").
5. Do not place the machine where it may be subjected to strong vibrations.
Front to back: Within 5 mm (0.2")
Right to left: Within 5 mm (0.2")
• These are the minimum space requirements.
Installation Requirements
C
D
E
A
B
Left
Rear
Right with bypass tray
Front
Right
Over 100 mm (3.9")
Over 100 mm (3.9")
Over 100 mm (3.9")
Over 750 mm (29.5")
Over 500 mm (19.7")
Put the machine near the power source with the clearance shown above.
• Main Machine Occupation Dimensions (W x D):
1187 mm (46.7") x 1535 mm (60.4")
In the following figure, MP C2504 is equipped with Paper Feed Unit PB3220/PB3210, Bridge Unit
BU3070 and Finisher SR3220.
53
2. Installation
54
A
B
F
G
H
I
C
D
E
1,155 mm / 45.47" (when equipped with ARDF)
1,205 mm / 47.44" (when equipped with SPDF)
125 mm / 4.92" (when equipped with ARDF)
175 mm / 6.89" (when equipped with SPDF)
1,030 mm / 40.55"
1,162 to 1,247 mm / 45.7" to 49.1"
575 to 660 mm / 22.63" to 25.98"
587 mm / 23.11"
575 mm / 22.63"
1,045 mm / 41.14"
986 mm / 38.81"
Installation Requirements
L
M
N
O
668 mm / 26.29"
587 mm / 23.11"
738 mm / 29.05"
685 mm / 26.96"
Models equipped with the ARDF (W × D × H up to ARDF):
587 × 685 × 913 mm (23.2 × 27.0 × 36.0 inches)
Models equipped with the SPDF (W × D × H up to SPDF):
587 × 685 × 968 mm (23.2 × 27.0 × 38.1 inches)
Models with no ADF (W × D × H up to exposure glass):
587 × 685 × 788 mm (23.2 × 27.0 × 31.1 inches)
Models equipped with the ARDF (W × D × H up to ARDF):
587× 685 × 913 mm (23.2 × 27.0 × 36.0 inches)
55
56
2. Installation
• Insert the plug firmly in the outlet.
• Do not use an outlet extension plug or cord.
• Ground the machine.
Destination
NA
EU
AP
CHN
Power supply voltage
Rated current consumption
Permissible voltage fluctuation
120 to 127 V 12 A or more
220 to 240 V 10 A
Image quality guaranteed:
108 V (120 V - 10%) to 138 V (127 V + 8.66%)
Machine operation guaranteed:
102 V (120 V - 15%) to 138 V (127 V + 8.66%)
Image quality guaranteed:
198 V (220 V - 10%) to 264 V (240 V + 10%)
Machine operation guaranteed:
187 V (220 V - 15%) to 276 V (240 V + 15%)
Main Machine Installation
In order to increase the security of the MFP, and to ensure that the customer sets the administrator password, an administrator set/change prompt display is shown up at the first power-up.
• The following Program/ Change Administrator screen is displayed at the first power-up.
• When the customers set the administrator/supervisor login password, the display disappears and the home display will appear. The customers, however, can erase this screen with the following procedure in the case that they think there is no need to set the password.
1.
On the Program/Change Administrator screen, press [Change] next to Supervisor and then press [OK] without inputting any password.
2.
Press [OK] again when the Confirm password display shows up.
3.
For Administrator 1, do the same procedure as steps 1 and 2.
4.
Press the [OK] button, and then turn the power OFF/ON.
• SP5-755-002 (Display Setting: Hide Administrator Password Change Scrn) allows you to skip this screen temporarily and continue the installation procedure without setting an administrator password. However, the Program/Change Administrator screen appears every time you turn the power OFF/ON, if the password is not set.
• For more details about this security issue, see "Notes on Using Multi-Function Printers Safely" supplied with the MFP.
• To enter the SP mode, there are two ways to display the number keyboard on screen;
1. Press the "Document Server" icon.
57
58
2. Installation
2. Press and hold the button [A] located at the left side of the operation panel and "Check Status
[B]" at the same time.
Main Machine Installation
Put the machine on the paper feed tray (1 tray/2 trays) first, then install the machine and other options.
You need Paper Feed Unit PB3220/PB3210 (D787) to align the paper transport path if you want to install Booklet Finisher SR3220 (D3B9).
59
60
2. Installation
No.
1 Power Cord
Description
2 Cap for scanner lock
3 End Fence
4 Image Transfer Front Cover
5 Decal - Paper Tray
6 Decal - Original Table for DF
7 Decal - Caution : Original : Multi Language
8 Cleaning Cloth
9 Cleaning Cloth Holder
10 Plate – Logo (Smart Operation Panel)
11 Plate – Logo (front cover) (for NA, EU, AA)
M3x8 Screws for Image Transfer Front Cover
Sheet: Safety (EU only)
CD-ROM – OI (AA only)
CD-ROM - Driver
Sheet: Exposure glass
Start Guide
Read This First
Sheet: EULA
Seal: Caution
Sheet: EMC address (EU only)
Caution: Smart Operation Panel
Caution: Smart Operation FCC (NA only)
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
Q’ty
1
2
1
1
No.
Caution: CE (EU only)
NFC Tag
Description
Bluetooth decal (for NA, EU, AA)
Main Machine Installation
Q’ty
1
1
1
• Remove the tape from the development units before turning the main power ON. The development units can be severely damaged if the tape is still attached.
1.
Remove the machine from the box, and check the items in the package.
Remove the retainer [A] at the lower front right before lifting up the machine, because the handle for lifting the machine is hidden by the retainer [A].
61
2. Installation
• When you lift the machine, hold the correct parts, as shown in the photo below.
• Do not hold any other parts of the machine when lifting it, because this might deform the machine or break the exterior covers
62
2.
Remove the orange tapes and retainers on the outside.
For a basic model
Main Machine Installation
For a model on which SPDF DF3100 is preinstalled, remove the orange tapes and retainers on the
SPDF.
For a model on which ARDF DF3090 is preinstalled, remove the orange tapes and retainers on the
ARDF.
63
2. Installation
64
3.
Remove the paper size decal [A] on the exposure glass.
4.
Remove the orange tapes on the scanner shipping locks.
Main Machine Installation
5.
Remove the two scanner shipping locks [A] by rotating them 90 degrees counter clockwise.
SC120 is displayed when the machine is turned ON with the shipping lock attached.
• Keep the scanner shipping locks with the machine. They must be used when transporting the
machine to another location. (page 91 "Moving the Machine")
65
66
2. Installation
6.
Attach the two caps [A] provided with the machine.
7.
Pull out the 1st/2nd paper trays, remove the orange tape.
8.
Remove the scanner support [A].
Main Machine Installation
9.
Open the front cover, and store the scanner support [A] in the storage location.
• Underneath the bracket [A] is the storage location for the factory setting sheet.
1.
Open the SPDF.
2.
Release the lever [A], open the pressure plate sheet [B], and pull out the protective sheet
[C] slowly.
3.
Remove the filament tape [D].
67
68
2. Installation
4.
Close the pressure plate sheet [A].
5.
Close the SPDF.
• If the protective sheet remains in the SPDF, a paper jam will be detected.
• Automatic initial adjustment will be done even if the seal was not removed correctly. But toner from a PCDU that still has the seal will not be able to reach the ITB, and will not be transferred to printouts and copies.
• If this happens, remove the PCDU seal and do SP2-111-004 (Forced Line Position Adj. Mode d).
• White stripes may appear in the printed images for the first 20k pages printing continuously in a low humid environment, due to the deviation of toner density adjustment. Except for that, the machine operates normally.
• SP descriptions
• SP2-111-004 (Forced Line Position Adj. Mode d)
Executes the fine line position adjustment and rough line position adjustment.
1.
Open the front cover.
Main Machine Installation
2.
Pull out the seals [A] for Y, M, C, and Bk.
3.
Rotate the ITB contact lever [A] clockwise, and set it to the position in the following picture.
4.
Attach the image transfer front cover [A] with the two screws (M3×8; provided with the accessories).
5.
Close the front cover.
69
2. Installation
1.
Clean the adhesive surface of the optical cloth pocket with an alcohol-soaked cloth.
2.
Attach the optical cloth pocket [A] to the left side of the scanner and put the optical cloth into the pocket.
1.
Attach the part [A] to the paper exit tray.
First, insert and attach the front pin (inside the blue circle).
70
Check the following points for the paper exit feeler [A] installed at the paper exit.
• It can move in line with the ejection of paper.
• It holds contact with the surface of the ejected paper and is still movable.
Main Machine Installation
Paper will get jammed in the following cases.
• The paper exit feeler does not function due to obstacles (such as cables).
• The paper exit feeler does not function when the paper is pulled out and pushed back again.
Attach the following decals provided with the machine accessories.
71
2. Installation
72
1: Original Set Decal
2: ADF Caution Decal
3: Paper Size Tray Number Decal
4: Brand Logo for Smart Operation Panel
5: Brand Logo for Front cover
Location for each decal
Main Machine Installation
1.
Open the front cover.
2.
Shake the toner bottle (Bk) 7 to 8 times.
73
2. Installation
3.
Remove the toner bottle protection cap [A].
4.
Push the toner bottle into the machine slowly.
5.
Set the toner bottles (Y, M, and C) in the same way.
6.
Close the front cover.
7.
Connect the power cord to the machine.
74
• Use the power cord that is provided with the machine. Do not use any other power cord. Also, do not use an extension cord.
8.
Turn ON the main power.
• Toner Initialization starts. It takes about 5 minutes to fill the toner up.
Be sure to wait long enough. If you do not, Auto Color Calibration (ACC) will take longer.
RTB 35
'Invalid firmware is installed'
Main Machine Installation
• Password change display appears. If you want to skip this screen, SP5-755-002 (Display
Setting: Hide Administrator Password Change Scrn) allows you to skip it. Refer to page 57
"Important Notice on Security Issues".
• When Supervisor/ Administrator 1-4 passwords are configured via network, the
"Change Supervisor login password" window will not display.
• The passwords for supervisor or administrator 1 to 4 can be set via "System Settings". But the Program/Change Administrator screen appears every time the power switch is turned ON if the passwords are input this way. So we recommend the customers to set the passwords via network or the Program/Change Administrator screen.
9.
Press [Change] and change the supervisor login password.
10.
Input the password, and then press [OK].
11.
Confirm the password, and then press [OK].
75
2. Installation
12.
Change the administrator 1 login password.
13.
Input the password, and then press [OK].
14.
Confirm the password, and then press [OK].
15.
After the toner initialization is completed, the machine beeps, and the following message is displayed. Turn the machine OFF/ON.
76
• Even though the control panel display has gone off, the machine may still be on. So when turning the power off and back on, be sure to check that the main power indicator has gone off before turning the power on again.
This procedure is required for the machine which the fax function is installed as standard.
1.
Open the ARDF original cover and stamp holder [A].
Main Machine Installation
2.
Install the fax stamp [A] provided with the machine.
3.
Close the holder.
Make sure that it is pushed in to the position where the marks on the holder and the exterior cover face each other. If not, jam detection (001) will occur.
77
78
2. Installation
• Perform the image quality test after installing all peripherals
• Confirm that there are no accessories (such as screws and clamps) left inside the main machine and peripherals
1.
Turn ON the main power.
2.
Check that the operation panel shows "No Paper" under the "Check Status" screen.
3.
The paper size is basically detected automatically.
1. Pull out the paper feed tray slowly until it stops.
2. Load the paper.
3. While pressing the release lever, adjust the side fence to the paper size to be set.
4. Set the back fence.
• If not transferred to printouts, the PCDU seals will not be removed correctly. Remove the PCDU seals, and then execute SP2-111-004 (Forced Line Position Adj. Mode d).
1.
Do the "Automatic Color Calibration (ACC)" for the copier mode & printer mode as follows:
- Copier mode -
1. "User Tools" icon > "Machine Features" > "Maintenance" > "Auto Color Calibration" >
"Copier Function" > "Start"
2. Press "Start Printing".
3. Put the printout on the exposure glass.
Main Machine Installation
4. Put 10 sheets of white paper on the test chart. This ensures the precise ACC adjustment.
5. Close the SPDF/ARDF or the platen cover.
6. Press "Start Scanning" on the LCD. Then, the machine starts the ACC.
- Printer mode -
1. "Printer Function" > "Start"
2. Select a test pattern.
• Print each ACC test pattern. There are 5 test patterns as follows:
Test Pattern 1: 600x600 dpi
Test Pattern 2: 1800x600 dpi
Test Pattern 3: 9000x600 dpi
Test Pattern 4: 1200x1200 dpi
Test Pattern 5: 3600x1200 dpi
3. Press "Start Printing".
4. Put the printout on the exposure glass.
5. Put 10 sheets of white paper on the test chart. This ensures the precise ACC adjustment.
6. Close the SPDF/ARDF or the platen cover.
7. Press "Start Scanning" on the LCD. Then, the machine starts the ACC.
79
2. Installation
8. Repeat steps 1 to 7 until all the ACC test patterns have been printed.
2.
Exit the User Tools mode.
3.
Press the “Document Server” icon.
Or press and hold the [A] key and "Check Status [B]" at the same time until the number keyboard screen is displayed.
4.
Enter the key code for SP mode.
80
5.
Perform line adjustment.
1. Execute SP2-111-004 (Forced Line Position Adj. Mode d)
2. The result can be checked with SP2-194-007 (MUSIC Execution Result)
0: Success, 1: Failure
Main Machine Installation
• If failure, execute SP2-111-004 once more and check the result again.
• Fix the color registration errors, referring to page 654 "Judgment for Type of Color
Also, results for each color can be checked with SP2-194-010 to 013 (MUSIC Execution
Result: Error Result C, M, Y, K).
1: Completed successfully
6.
Exit the SP mode.
SP descriptions
• SP2-111-004 (Forced Line Position Adj. Mode d)
Executes the fine line position adjustment and rough line position adjustment.
• SP2-194-007 (MUSIC Execution Result: Execution Result)
Displays the result code of MUSIC adjustment.
0: Success
1: Failure
• SP2-194-010 to 013 (MUSIC Execution Result: Error Result C,M, Y, K)
Displays the result code of MUSIC adjustment for each color.
0: Not done
1: Completed successfully
2: Cannot detect patterns
3: Fewer lines on the pattern than the target
4: Out of the adjustment range
5 to 9: Not used
Make a copy of a test chart and check the output quality.
Adjusts the side-to-side registration, refer to the “Image Adjustment” > “Registration” section.
1.
Enter SP2-109-003.
2.
Print out the test pattern (14: Trimmed area) with SP2-109-003.
3.
If necessary, adjust the registration for the paper feed tray.
• SP1-002-001 (Side-to-Side Registration: By-pass Tray)
81
82
2. Installation
• SP1-002-002 (Side-to-Side Registration: Paper Tray 1)
• SP1-002-003 (Side-to-Side Registration: Paper Tray 2)
• SP1-002-006 (Side-to-Side Registration: Duplex)
If optional paper trays is installed, do the following SPs as well:
• SP1-002-004 (Side-to-Side Registration: Paper Tray 3)
• SP1-002-005 (Side-to-Side Registration: Paper Tray 4)
4.
If necessary, adjust the registration for ADF.
• SP6-006-001 (ADF Adjustment: Side-to-Side Regist: Front)
• SP6-006-002 (ADF Adjustment: Side-to-Side Regist: Rear)
5.
If necessary, adjust the registration for Scanner.
• SP4-803-001 (Home Position Adj Value)
• SP4-011-001 (Main Scan Reg)
• SP descriptions
• SP1-002 (Side-to-Side Registration)
Adjusts the side-to-side registration by changing the laser main scan start position for each mode and tray.
Increasing a value: The image is moved towards the rear edge of the paper.
Decreasing a value: The image is moved towards the front edge of the paper.
• SP2-109-003 (Test Pattern: Pattern Selection)
Selects the test pattern.
Specify ARFU settings as required.
Operating Conditions:
• Use the machine in an environment where it can be connected to the Internet.
• Auto remote firmware update (ARFU) requires connection to an external network. Be sure to get permission from the customer before setting ARFU up.
• The connection is one-way, so the user’s data cannot be accessed from the global server.
Pre-Operation Set Up and Checks
1.
Check the network settings (IP address, Subnetmask, Gateway, and Proxy).
Main Machine Installation
2.
Check the DNS setting.
How to Check the DNS setting
1. Get the IP address of the DNS server from the customer.
2. Request the customer to check the DNS server.
• How to check the address of the DNS server by the PC (reference).
Check by either of the following methods:
Run "ipconfig / all" at the command prompt on the PC, then check the IP address of the DNS server.
Open the IPv4 properties screen in the PC, check the IP address setting of the DNS server is whether manual or automatic.
• If the access to the external server is restricted, request the network administrator (customer) to permit the following FQDN name for communication.
- FQDN: p-rfu-ds2.support.ricoh.com
3.
Ask the customer the prohibited time and day of the week of ARFU execution.
4.
Check SP5-816-087 (Remote Service: CERT:Macro Ver) and make sure the encryption level is 2048 bit.
[1]: 512 bit / [2]: 2048 bit
• If SP5-816-087 is [1]: 512 bit, specify the settings as follows:
1. Initialize the encryption level by executing SP5-870-003 (Common Key Info Writing:
Initialize)
2. Rewrite as 2048 bit in SP5-870-004 (Common Key Info Writing: Writing 2048 bit).
3. Turn off and on the main switch.
• ARFU uses the same certificate as @Remote to communicate with the Global Server. This may cause failure in connecting with the Center Server, if the device is to be installed in the following conditions. Make sure to check the conditions before changing the encryption level and do the corresponding workaround.
Conditions
1) Customer uses RC Gate Type BN1.
RC Gate Type BN1 does not support 2048 bit encryption level communication with Ricoh devices (HTTPS Managed device). Therefore, device cannot be registered under RC Gate
Type BN 1 in this case.
2) Ricoh device (HTTPS Managed) that supports only 512 bit encryption level is registered as external appliance.
83
84
2. Installation
Only one encryption level can be set for an external appliance for its communication with imaging devices. If a 512 bit encryption level Ricoh device (HTTPS Managed) is registered, the external appliance as well as other devices must also use 512 bit encryption level even if
248 bit encryption is supported on those devices.
Workaround
For Condition 1:
Advise your customer to change to the latest appliance that supports 2048 bit encryption level communication.
For Condition 2:
1. Manage the device with embedded RC Gate. (2048 bit)
2. Exclude non-supported devices from the external appliances, and then, change the encryption level of external appliance and all managed devices (from 512 bit to 2048 bit).
Devices excluded to be registered with embedded RC Gate. (512 bit)
Configuration Procedure
1.
Do interface settings.
In User Tools > Machine Features > System Settings > Interface Settings, specify the machine’s IPv4 address, subnet mask, and gateway IPv4 address.
2.
Do DNS settings and check the connection.
In User Tools > Machine Features > System Settings > Interface Settings > DNS Settings
• If the setting of the DNS IP address is automatic, select [Auto-Obtain (DHCP)] at the MFP machine's DNS settings.
• If the setting of the DNS IP address is manual, select [Specify] and specify the DNS server 1 to
3.
• Press [Connection Test] to check the connection with the input address. Make sure that it is connected successfully.
Main Machine Installation
3.
Check the user’s network environment and, as required, specify the proxy server settings in the following SPs:
• SP5-819-062 (Use Proxy DFU(SSP))
1: Use / 0: Not use
• SP5-816-063 (Use Proxy DFU(SSP))
• SP5-816-064 (Proxy Port Number)
• SP5-816-065 (Proxy User Name)
• SP5-816-066 (Proxy Password)
They can be specified also via Web Image Monitor from Device by logging in with the administrator authorization. Management>Configuration>Device Setting>Auto Firmware Update.
• “Auto Firmware Update" will appear on Web Image Monitor if
SP5-886-111(AutoUpdateSetting) is set to "1(ON)."
4.
Set SP5-886-111 (AutoUpdateSetting) to "1(ON)."
• To download the firmware only using SFU, and not by ARFU, specify the settings as follows:
- SP5-886-111(AutoUpdateSetting) to "0 (OFF)"
- SP5-886-115 (SfuAutoDownloadSetting) to "1 (ON)"
5.
Set the prohibited day of the week, and time, of the auto firmware update.
6.
Consider usages of customer’s MFP, change the following as needed.
• SP5-886-112 (AutoUpdateProhibitTermSetting)
0: OFF, 1: ON (Default )
• SP5-886-113 (AutoUpdateProhibitStartHour)
Default: 9
• SP5-886-114 (AutoUpdateProhibitEndHour)
Default: 17
• SP5-886-120 (AutoUpdateProhibitDayOfWeekSetting)
Default: 0x00
Set the bits for the days of the week to prohibit updating.
Prohibited (Monday - Sunday): Bit 7
Monday: bit 6
Tuesday: bit 5
Wednesday: bit 4
Thursday: bit 3
85
2. Installation
Friday: bit 2
Saturday: bit 1
Sunday: bit 0 e.g.) Prohibited on Mon., Fri., Sat., and Sun.: 0x47 (01000111)
They can be specified also via Web Image Monitor logged in as the machine administrator from
Device. Management>Configuration>Device Setting>Auto Firmware Update.
• “Auto Firmware Update" will appear on Web Image Monitor if
SP5-886-111(AutoUpdateSetting) is set to "1(ON)."
7.
Use the machine with its main power on and connected to the Internet.
Checking the ARFU Connection
1.
Enter the SP mode.
2.
Press [Firmware update].
3.
Press [Update].
4.
Press [Execute update].
86
• ”Execute update” appears even if @Remote connection has not been established.
• If an error code appears when you click “Execute update”, the machine is in the following status.
Error code
E51
E71
Status
The machine in operation for printing, etc.
Network connection error
(Other error, see page 680 "Error Screens During Updating")
Main Machine Installation
5.
Check if one of the following messages appears: "Will you download the latest package
Ver *** and update?" or "The installed package is the latest version.".
• If the message appears, it is possible to execute ARFU.
->Press “No” and close SP mode to complete the configuration.
• If the message does not appear, it is not possible to execute ARFU.
->Check the network settings again.
• Update will run immediately if you press “Yes” at the message "Will you download the latest package Ver *** and update?" Update cannot be canceled, as it is run by SFU. (Update can be canceled for ARFU.)
• If the access to the global server is restricted, request the network administrator (customer) to permit the following FQDN name for communication.
- FQDN: p-rfu-ds2.support.ricoh.com
• SP5-886-116 (Auto Update Prohibit Term Setting) displays the scheduled date and time of the next
ARFU.
• If the scheduled date and time of the next ARFU coincides with a time and day of the week when
ARFU is prohibited, the machine sends an inquiry to the server to check if there is a new firmware package at this time. If there is a new firmware package, it is downloaded in the background, but the package updating is cancelled and executed on the next occasion, 76 hours later, to update the package.
Specifying the Time and Day of the Week to Prohibit Updating via Web Image Monitor
1.
Start the Web Image Monitor.
2.
Log in as the machine administrator.
3.
Point to [Device Management], and then click [Configuration].
87
2. Installation
4.
Click "Auto Firmware Update".
88
• Turn the main power OFF and back ON again after setting SP5-886-111
(AutoUpdateSetting) to "1(ON)". "Auto Firmware Update" will appear in the menu list of the
Web Image Monitor.
5.
In the applicable items, specify the times and days of the week to prohibit updating.
Select the check boxes of the applicable days of the week to prohibit updating on that day
Main Machine Installation
The Copy Data Security function is installed in the IPU as standard for this machine.
Enable this function in User Tools when installing the machine.
1.
Press [User Tools] icon on the HOME screen.
2.
Select [Machine Features] > [System Settings] > [Administrator Tools] > [Detect Data
Security for Copying] > "On".
Copy Data Security Function
If the Unauthorized Copy Prevention function is enabled, embedded text patterns (for instance, a warning message such as "No Copying") are displayed when documents are copied illegally.
Accordingly, unauthorized copying can be prevented.
If the Data Security for Copying function is used and settings for special patterns embedded in documents are enabled, copies of documents with embedded patterns are printed with gray overprint. Accordingly, information leakage can be prevented. To protect documents by gray overprint, the Data Security for Copying function must be enabled on the copier or multi-function printer.
Perform the encryption and overwrite settings to protect the user information in the HDD as necessary.
Follow the instructions in page 374 "Security Settings".
Change the necessary settings for the following SP modes if the customer has made a service contract.
89
90
2. Installation
SP No.
SP5-045-001
Counter method
SP5-104-001 (SSP)
A3/DLT double count
SP5-812-001 and
-002
Service Tel:
Telephone / Facsimile
Function
Specifies if the counting method used in meter charge mode is based on developments, prints, or coverage.
Default
"1": Prints
Specifies whether the counter is doubled for A3/DLT paper.
"0":Single counting
-001: shows or sets the telephone number of the service representative.
-002: shows or sets the fax number of the service station. The number is printed on the counter list when the "Meter Click Charge" is enabled. User can send a fax message with the counter list.
Counter Display Method
There are 3 types (Developments, Prints and Coverage). Display mode can be set by SP5-045-001
(Accounting counter: Counter Method).
Value Mode
0
1
2
Development Count
Print Count
(Default)
Coverage Count
Descriptions
YMC Development Counter
Bk Development Counter
Color Copy Counter
B&W Copy Counter
Color Print Counter
B&W Print Counter
Color Total Counter
B&W Total Counter
Color Total Counter
B&W Total Counter
Color Coverage Counter 1
Color Coverage Counter 2
Color Coverage Counter 3
Main Machine Installation
Value
7
Mode
Coverage Count (YMC)
Descriptions
Color Total Counter
B&W Total Counter
Color Coverage Counter 1 (YMC)
Color Coverage Counter 2 (YMC)
Color Coverage Counter 3 (YMC)
Installation is now completed.
This section shows you how to manually move the machine from one floor to another floor. Before turning off the main power, make sure 100% is shown as available memory on the screen if the fax option is installed.
• Turn off the main power.
• Disconnect the power plug from the outlet.
• Close all covers and paper trays, including the front cover and bypass tray.
• Move the scanner carriage to the correct position [A] with SP4-806-001 (SSP), and reattach the scanner shipping locks with lock position [B].
• Keep the machine level and carry it carefully, taking care not to jolt or tip it, and protect the machine from strong shocks.
• When moving the machine, do not press against the ADF.
• Remove the optional feed tray when lifting the main machine for moving it to another floor.
91
2. Installation
• SP descriptions
• SP4-806-001 (Scanner carriage storage operation) (SSP)
Moves the scanner carriage to the shipping lock position. Attach the scanner shipping locks and fix the scanner carriage after executing SP4-806-001.
• Do not push the center part of the rear cover. Do not hold the covers of the stabilizers.
92
• Do not put hard pressure on the rear cover [A] when moving or picking up the machine as it is fragile. This also applies to the operation panel [C]. Hold part [B] when moving the machine.
Main Machine Installation
• Hold 4 corners on the bottom base when holding the machine with the optional paper feeding tray joined to the main machine. Do not hold any other parts.
1.
Position the machine so that its left side faces the wall. Make sure to put cushioning in between.
2.
Fasten the belt at the ridge line with cushioning.
3.
Make sure that the belt is over the front cover (at 45 – 75 cm height from the ground).
93
94
2. Installation
Anti-Condensation Heater (Scanner, PCDU)
• Unplug the machine power cord before starting the following procedure.
• Do the following procedure not to damage any harnesses.
• Check that harnesses are not damaged or pinched after installation.
• This option is provided as a service part.
• If you want to install Anti-Condensation Heater (Scanner), (1) heater for scanner and (2) electrical components should be ordered.
(1) Heater for Scanner
No.
Description
1 COVER: HEATER: SCANNER
2
HEATER:120V:9W
HEATER:230V:9W
3 BRACKET HEATER: SCANNER
5
SCREW:POLISHED ROUND/
SPRING:M4x8
6 SCREW M3x3
1
2
Q’ty Remarks
2 Parts Number:
1
• NA (120V): D2380071
• EU/AA (220/240V):
D2380072
1
95
96
2. Installation
(2) Electrical components
No.
Description
TAPPING SCREW M3X6
4 CLAMP
HARNESS: SCANNER/PCU
PCB: DHB
HARNESS :DC: DHB
HARNESS :AC: DHB
Q’ty Remarks
3 Parts Number:
6
D2386650
1
1
Electrical parts set for Scanner and
Drum heater is common between
NA/EU
1
1
1.
Remove the rear cover [A].
Anti-Condensation Heater (Scanner, PCDU)
2.
Remove the rear lower cover [A].
3.
Remove the power supply box [A] ( x6, Among them, tapping screw x1)
97
98
2. Installation
4.
Release the 5 clamps.
5.
Remove the HVP-CB with bracket [A] (Hook x2).
Anti-Condensation Heater (Scanner, PCDU)
6.
Connect the combined Blue/White harness to the back frame [A].
• The harness will be connected to the relay board. See the details in step 8.
7.
Reinstall the HVP-CB unit and power supply box.
99
100
2. Installation
8.
Secure the relay board to the main machine and connect the Blue/White harness to the socket on the board ( × 1, × 3).
9.
Connect the harnesses on the relay board to the sockets on the PSU.
• Two types of harnesses are packed with the heater. Both the Blue/White one [A] and the
Gray one [B] must be connected as shown below.
Anti-Condensation Heater (Scanner, PCDU)
10.
Remove the right rear cover [A] ( x4, among them, tapping screw x1)
11.
Remove a screw.
12.
Remove the scanner right cover [A].
Remove the hook at the upper part, and then slide the cover in the rear direction.
101
102
2. Installation
13.
Route the harness around the outside of the PSU and pull the harness out of the electrical box through the hole [A] ( x 4).
14.
Route the harness in the direction of the scanner ( x 6).
Anti-Condensation Heater (Scanner, PCDU)
• Fasten the clamp between the bindings of the harness at the location indicated by the red circle.
15.
Attach the connector to the frame.
Connect it to the heater harness in step 25.
103
104
2. Installation
16.
Remove the scale [A]
17.
Remove the sheet-through exposure glass [A]
18.
Remove the rear scale [A]
Anti-Condensation Heater (Scanner, PCDU)
19.
Remove the left scale and exposure glass [A]
• The exposure glass and the left scale are attached with double-sided tape.
20.
Move the scanner carriage to the right.
105
2. Installation
21.
Attach the heater [B] to the bracket [A] provided with the accessories ( × 2).
22.
Remove the release paper [A] on the back side of the bracket, and secure the heater [B] with the seal, aligning it with the boss on the frame.
106
23.
Pull the harness [A] out of the frame hole.
Route the harness into the harness guide.
Anti-Condensation Heater (Scanner, PCDU)
24.
Attach the heater cover [A] ( × 1).
25.
Connect the heater harness that was pulled out of the frame hole to the connector which was mounted in step 15.
26.
Reattach all the removed covers.
107
108
2. Installation
• This option is provided as a service part.
• If you want to install Anti-Condensation Heater (PCDU), electrical parts (1) and heater for PCDU
(2) should be ordered.
(1) Electrical parts
Description
TAPPING SCREW M3X6
CLAMP
HARNESS: SCANNER/PCU
PCB: DHB
HARNESS :DC: DHB
HARNESS :AC: DHB
(2) Heater for PCDU
Description
TAPPING SCREW: WASHER M3X8
HEATER: PHOTOCONDUCTOR: EU
HEATER: PHOTOCONDUCTOR: NA
DECAL HIGHT TEMP
Q’ty
3
6
1
1
1
1
Remarks
Parts Number:
D2386650
Electrical parts set for Scanner and Drum heater is common between NA/EU
Q’ty
1
1
Remarks
Parts Number:
• NA (120V): D7390116
• EU/AA (220/240V): D7390117
1
1.
Remove the rear cover [A].
Anti-Condensation Heater (Scanner, PCDU)
2.
Remove the rear lower cover [A].
3.
Remove the power supply box [A] ( x6, Among them, tapping screw x1)
109
110
2. Installation
4.
Release the 5 clamps.
5.
Remove the HVP-CB with bracket [A] (Hook x2).
Anti-Condensation Heater (Scanner, PCDU)
6.
Connect the combined Blue/White harness to the back frame [A].
• The harness will be connected to the relay board. See the details in step 8.
7.
Reinstall the HVP-CB unit and power supply box.
111
112
2. Installation
8.
Secure the relay board to the main machine and connect the Blue/White harness to the socket on the board ( × 1, × 3).
9.
Connect the harnesses on the relay board to the sockets on the PSU.
• Two types of harnesses are packed with the heater. Both the Blue/White one [A] and the
Gray one [B] must be connected as shown below.
Anti-Condensation Heater (Scanner, PCDU)
10.
Remove the right rear cover [A] ( x4, among them, tapping screw x1)
11.
Remove a screw.
12.
Remove the scanner right cover [A].
Remove the hook at the upper part, and then slide the cover in the rear direction.
113
114
2. Installation
13.
Route the harness around the outside of the PSU and pull the harness out of the electrical box through the hole [A] ( x 4).
14.
Route the harness in the direction of the scanner ( x 6).
Anti-Condensation Heater (Scanner, PCDU)
• Fasten the clamp between the bindings of the harness at the location indicated by the red circle.
115
116
2. Installation
15.
Attach the connector to the frame.
16.
Remove Feed Trays 1 and 2.
17.
The connecter cover located inside the machine [A] ( × 1).
18.
Temporarily tighten a screw at the top ( M3x8: x1).
Anti-Condensation Heater (Scanner, PCDU)
19.
Install the heater [A] by connecting the connector to the inside of the machine, then tighten the screw completely.
• Hold the heater against the inside during final tightening.
20.
Reinstall the connector cover ( × 1).
117
118
2. Installation
21.
Attach the warning decal [A].
22.
Reassemble the machine.
23.
Connect the power cord, and then check that the heater is being powered and heated.
Anti-Condensation Heater for Paper Feed Trays
• Unplug the machine power cord before starting the following procedure.
• Do the following procedure not to damage any harnesses.
• Check that harnesses are not damaged or pinched after installation.
Anti-Condensation Heater (Service Option) for Main Machine
No.
1
2
Description
Tray heater
Tapping screw: M3 X 8
Q’ty Remarks
1 Heater and harness
Parts Number:
2
• NA (120V): D2386630
• EU/AA (220/240V): D2386640
3
4
5
6
7
PCB: DHB
Harness for tray
Harness for DC
Harness for AC
Tapping screw: M3 X 6
1 Electrical components
1
Parts Number:
• NA (120V): D2386661, *D2386660
1
1
• EU/AA (220/240V): D2386662,
*D2386660
3
*: Old parts number
Anti-Condensation Heater (Service Option) for Optional Paper Feed Unit
No.
Description Q’ty Remarks
1
2
3
Tray heater
Harness
Spring screw:M4 X 10
1 Heater and harness
1
Parts Number:
• NA (120V): D6931117
3
• EU/AA (220/240V): D6931127
Those parts number is common with MP C2003/
C2503.
RTB 36
Additional information
119
120
2. Installation
1.
Remove the rear cover [A].
2.
Remove the rear lower cover [A].
3.
Attach PCB: DHB ( X 3).
Anti-Condensation Heater for Paper Feed Trays
4.
Connect the two harnesses between "PCB: DHB" and "PSU".
• Red dashed circled cable is only white for NA, red for EU/AA.
5.
Connect connector 1.
6.
Connect connector 2 to the harness already attached.
121
122
2. Installation
7.
Attach connector 3 for the optional paper bank.
• This cable is only white for NA/EU/AA.
8.
Remove trays 1 and 2 from the machine.
Anti-Condensation Heater for Paper Feed Trays
9.
Connect the connector of the heater to the main machine.
10.
Install the heater inside the machine ( x 1).
123
124
2. Installation
11.
Reattach trays 1 and 2.
1.
Perform Steps 1 to 7 of
page 120 "Connecting to Main Machine Tray"
.
2.
Pull out the 1st and 2nd paper feed trays of the paper feed unit.
3.
Pass the harness of the heater [A] for the optional paper feed unit through the hole in the inner rear frame of the optional paper feed unit, and then attach it ( x1).
4.
Remove the securing brackets [A] of the optional paper feed unit.
Anti-Condensation Heater for Paper Feed Trays
5.
Remove the rear cover [A] of the optional paper feed unit.
6.
Remove the bracket [A] on the bottom of the main unit ( x1).
The removed bracket can be discarded.
125
2. Installation
7.
Connect the PFU harness [A] of the optional paper feed unit to the relay harness [B] of the main unit and the heater harness [C] ( x4).
126
8.
Reinstall the removed parts and covers.
9.
Connect the power supply cord and turn ON the main power.
Do the following two steps to set the anti-condensation heater to be constantly ON.
1. Set the setting of SP5-805-001 (Anti-Condensation Heater ON/OFF setting) to [1].
2. Manually disconnect the PCU and scanner heaters.
• The PCU and scanner heaters must be disabled because the temperature in the machine could become too high, causing problems with toner clogging, or damage to the scanner lamp stabilizer
1.
Perform Steps 1 to 7 of
page 120 "Connecting to Main Machine Tray"
.
2.
Pull out the paper feed tray of PB3150.
Anti-Condensation Heater for Paper Feed Trays
3.
Put the harness of the heater [A] for the optional paper feed unit through the hole at the inner rear frame, and then attach it ( x1).
4.
Remove the securing brackets [A] of Paper Feed Unit PB3150.
5.
Remove the rear cover [A] of Paper Feed Unit PB3150.
6.
Remove the bracket [A] on the bottom of the main unit ( x1).
The removed bracket can be discarded.
127
2. Installation
7.
Connect the PFU harness [A] of the optional paper feed unit to the relay harness [B] of the main unit and the heater harness [C] ( x4).
128
8.
Reinstall the removed parts and covers.
9.
Connect the power supply cord and turn ON the main power.
Do the following two steps to set the anti-condensation heater to be constantly ON.
1. Set the setting of SP5-805-001 (Anti-Condensation Heater ON/OFF setting) to [1].
2. Manually disconnect the PCU and scanner heaters.
• The PCU and scanner heaters must be disabled because the temperature in the machine could become too high, causing problems with toner clogging, or damage to the scanner lamp stabilizer
Paper Feed Unit PB3220 (D787-18, -22)/ PB3210 (D787-17)
No.
1 Screws (M4 × 10)
Description
2 Screw with Spring Washer (M4 × 10)
3 Securing Bracket
Q’ty
2
1
2
Remarks
• The main machine weighs approximately 100 kg. Make sure to lift it with the help of at least one more person.
• The machine should be held at the correct locations and lifted gently. If it is lifted without care, handled carelessly or dropped, it may result in an injury.
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• Be sure to join the machine to the paper feed unit so as to prevent equipment from falling over. If they are not connected, they may move and fall over, resulting in injury.
129
2. Installation
1.
Remove the orange tapes and retainers.
2.
Remove the accessories (fixing screws, etc.) (provided with the machine) from the package.
3.
Holding the grips on the machine, align the machine with the locating pins [A], and place the machine on the paper feed unit.
130
• When you lift the machine, hold the correct locations.
Paper Feed Unit PB3220 (D787-18, -22)/ PB3210 (D787-17)
• Do not hold any other parts of the machine when lifting it, because this may cause the machine to deform.
• Do not put the machine down on the paper feed unit as a temporary resting place. This may cause the paper feed unit to deform. Always connect the machine and paper feed unit properly.
4.
Pull out the 2nd paper feed tray.
5.
Using a securing bracket as a screwdriver, fix the machine to the feed unit (spring washer: screw: M4×10: 1).
131
2. Installation
6.
Attach the securing brackets [A] to two positions on the left and right at the rear of the machine (screws: 1 each).
7.
Reattach the paper feed tray to the machine
8.
Attach the decals as shown below.
132
[A]: Tray number decal
[B]: Paper size decal
• The tray number decal and paper size decal are packaged together with the machine.
9.
Lock the casters of the paper feed unit.
Paper Feed Unit PB3220 (D787-18, -22)/ PB3210 (D787-17)
10.
Connect the power cord to the machine.
• Stabilizers are attached to the machine when it is shipped. Do not remove them.
11.
Turn ON the main power.
12.
Set the paper, and check that the paper size set in the paper feed tray is displayed on the operation panel.
13.
Adjust the registration for the paper feed unit.
• SP1-002-004 (Side-to-Side Registration Paper Tray 3)
• SP1-002-005 (Side-to-Side Registration Paper Tray 4)
SP descriptions
• SP1-002 (Side-to-Side Registration)
Adjusts the side-to-side registration by changing the laser main scan start position for each mode and tray.
133
134
2. Installation
Increasing a value: The image is moved towards the rear edge of the paper.
Decreasing a value: The image is moved towards the front edge of the paper.
Paper Feed Unit PB3150 (D694)
No.
Descriptions
1 Securing Bracket
2 Screws - M4 × 10
3 Screw with Spring Washer - M4 × 10
Q’ty
2
2
1
Remarks
• The main machine weighs approximately 100 kg. Make sure to lift it with the help of at least one more person.
• The machine should be held at the correct locations and lifted gently by two people. If it is lifted without care, handled carelessly or dropped, it may result in injury.
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• Be sure to join the machine to the paper feed unit so as to prevent equipment from falling over. If they are not connected, they may move and fall over, resulting in injury.
135
2. Installation
• Paper Feed Unit PB3150 is not supplied with a caster. You can attach the optional page 140
"Caster Table Type M3 (D178)".
1.
Remove the orange tapes and retainers.
2.
Remove the accessories (fixing screws, etc.) (provided with the machine) from the package.
3.
Holding the grips on the machine, align the machine with the locating pins [A], and place the machine on the paper feed unit.
136
• When you lift the machine, hold the correct locations.
Paper Feed Unit PB3150 (D694)
• Do not hold any other parts of the machine when lifting it, because this may cause the machine to deform.
• Do not put the machine down on the paper feed unit as a temporary resting place. This may cause the paper feed unit to deform. Always connect the machine and paper feed unit properly.
4.
Pull out the 2nd paper feed tray.
5.
Using a securing bracket as a screwdriver, fix the machine to the feed unit (spring washer: screw: M4×10: 1).
137
2. Installation
6.
Attach the securing brackets [A] to two positions on the left and right at the rear of the machine (screws: 1 each).
7.
Reattach the paper feed tray to the machine.
8.
Attach the decals as shown below.
138
[A]: Tray number decal
[B]: Paper size decal
• The tray number decal and paper size decal are packaged together with the machine.
9.
Connect the power cord to the machine.
10.
Turn ON the main power.
11.
Set the paper, and check that the paper size set in the paper feed tray is displayed on the operation panel.
Paper Feed Unit PB3150 (D694)
12.
Adjust the registration for the paper feed unit.
SP1-002-004 (Side-to-Side Registration Paper Tray 3)
SP descriptions
• SP1-002 (Side-to-Side Registration)
Adjusts the side-to-side registration by changing the laser main scan start position for each mode and tray.
Increasing a value: The image is moved towards the rear edge of the paper.
Decreasing a value: The image is moved towards the front edge of the paper.
139
2. Installation
No.
Description
1 Right Lower Cover
2 Securing Bracket
3 Screws (M4 × 10)
4 Screw with Spring Washer (M4 × 10)
2
2
1
Q’ty
1
Remarks
Not used when Paper Feed Unit
PB3150 is installed.
140
• The main machine weighs approximately 100 kg. Make sure to lift it with the help of at least one more person.
• The machine must be held at the correct locations, and must be lifted slowly. If it is lifted with force, handled carelessly or dropped, it will result in an injury.
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• Be sure to join the machine and caster table to prevent equipment from falling over. If it is not joined, the machine will move or fall over, which will result in an injury.
Caster Table Type M3 (D178)
1.
Holding the grips on the machine, align the machine with the locating pins, and place the machine on the caster table.
• When you lift the machine, hold the lifting handles.
• Do not hold any other parts of the machine when lifting it, because this may cause the machine to deform.
• Do not put the machine down on the caster table as a temporary resting place. This may cause the machine to deform. Always connect the machine and caster unit properly.
2.
Pull out the 2nd paper feed tray.
3.
Using a securing bracket, fix the machine to the paper tray unit (spring washer: screw:
M4×10: 1).
4.
Attach the securing brackets at 2 positions to left and right at the rear of the machine
(screws: 1 each).
5.
Reattach the 2nd paper feed tray to the machine.
141
142
2. Installation
1.
Place the paper feed unit [B] on the caster table [A].
2.
Pull out the 1st paper feed tray.
3.
Using a securing bracket, fix the caster table to the paper tray unit (spring washer: screw:
M4×10: 1).
4.
Attach the securing brackets at 2 positions to left and right at the rear of the paper tray unit (screws: 1 each).
5.
Reattach the paper feed tray.
Platen Cover PN2000 (D700)
Check that you have the accessories indicated below.
No.
1
2
3
4
Platen Cover
Platen Sheet
Descriptions
Feeler Guide
Stepped Screw
Q’ty
1
1
1
2
Remarks
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
143
144
2. Installation
1.
Install the stepped screws ( × 2).
2.
Install the feeler guide [A].
3.
Install the platen cover [A].
Platen Cover PN2000 (D700)
4.
Place the platen sheet [A] on the exposure glass.
5.
Line up the rear left corner of the platen sheet flush against corner [B] on the exposure glass.
6.
Close the platen cover.
7.
Open the platen cover.
8.
Press the surface of the platen sheet gently to fix it on the platen cover securely.
145
2. Installation
No.
1 ARDF
Description
2 Screw
3 Knob Screw
4 Stud Screw (Small)
5 Stud Screw (Large)
6 Attention Decal – Top Cover
Q’ty
1
2
2
1
1
1
Remarks
146
• Turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
ARDF DF3090 (D779)
• Do not turn the power on until you perform "adjustment after installation," or it may not start normally.
1.
Remove all the tapes and shipping retainers.
2.
Insert the two stud screws ([A] is the larger stud, [B] is the smaller stud).
3.
Mount the ARDF [A] by aligning the screw keyholes [B] of the ARDF support plate over the stud screws.
4.
Slide the ARDF toward the front of the machine.
5.
Secure the ARDF with the two knob screws [C].
6.
Align the rear left corner of the platen sheet [A] with the corner [B] on the exposure glass.
7.
Close the ARDF.
147
2. Installation
8.
Open the ARDF and check that the platen sheet is correctly attached.
148
9.
Remove the rear cover [A].
10.
Remove the small disposable cover [A] on the rear cover (on the right side).
ARDF DF3090 (D779)
11.
Connect the ARDF cable as shown and mount the bracket [A] on the machine’s rear frame.
Make sure to connect the grounding wire.
12.
Connect the scanner cable to the connector at the machine’s rear.
13.
Reattach the rear cover.
14.
Lift the ARDF original tray.
149
150
2. Installation
15.
Slide the stamp holder [A] out and install the stamp cartridge in it, if necessary.
• After the stamp installation, be sure to slide the holder in correctly. Make sure to slide it in thoroughly until the reference marks on the holder and exterior cover are aligned. If it is not mounted correctly, the machine detects a J001 paper jam.
ARDF DF3090 (D779)
16.
Attach the decals [A] [B] to the top cover as shown. Choose the language that you want.
17.
Plug in and turn ON the main power.
18.
Set SP4-688-001 (DF Density Adjustment ARDF) to "106".
19.
Check the ARDF operation, and make a full size copy. Check that the registrations (sideto-side and leading edge) and image skew are correct. If they are not, adjust the registrations and image skew (see
When feeding thin paper, adjust the sliding tray to the point shown below [A].
When feeding normal paper, adjust the sliding tray to the point shown below [B].
If not, it may cause problems as follows:
• Original jam
• Original curl
• Originals cannot be stacked neatly
151
152
2. Installation
No.
Description
1 Attention Decal – Top Cover
2 Ferrite Core (L)
3 Ferrite Core (S)
4 Face-Up Document Decal
5 Knob Screw
6 Stud Screw
7 Screw (3x6)
Q’ty
1
1
1
1
2
2
4
Remarks
SPDF DF3100 (D3B0)
• Turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• Do not turn the power on until you perform "adjustment after installation," or it may not start normally.
1.
When unpacking, hold both sides of the SPDF and take it out of the box.
153
2. Installation
2.
Place the unit on the machine temporarily, and remove the orange tapes and shipping retainers.
154
3.
Remove the accessories in the package (boards, fixing screws, etc.).
4.
Attach the 2 stepped screws to the machine.
SPDF DF3100 (D3B0)
5.
Align the hinges of the SPDF with the stepped screws, and attach them by sliding them in.
155
2. Installation
6.
Fix the SPDF to the machine (coin screws×2)
7.
Release the lever [A], then open the pressure plate sheet [B], and gently remove the protective sheet [C].
8.
Remove the filament tape, and shut the pressure plate sheet.
156
9.
Remove the platen sheet [A], and set it on the exposure glass.
Align it with the left scale and rear scale of the printer.
10.
Close the SPDF slowly, and attach the platen sheet and SPDF.
11.
Remove the rear cover [A].
SPDF DF3100 (D3B0)
157
158
2. Installation
12.
Remove the small disposable covers [A] on the rear cover.
13.
Remove the controller box cover [A].
Red Circle: Remove, Blue Circle: Loosen
14.
Connect the SPDF cable as shown and mount the brackets [A] [B] on the machine’s rear frame.
Make sure to connect the grounding wire.
15.
Connect the scanner cable to the connector at the machine’s rear.
SPDF DF3100 (D3B0)
159
160
2. Installation
16.
Attach the scanner cable [A] with the bracket on the upper frame of the controller box.
17.
Connect the cable to the IPU (CN564).
18.
Tuck in the excess length portion of the cable to the back of the machine.
SPDF DF3100 (D3B0)
19.
Attach the supplied ferrite core (L) [A] and ferrite core (S) [B].
Attach [A] close to the connector.
Attach [B] in the area near the end of the tube.
20.
Reattach the controller box cover and the rear cover.
161
162
2. Installation
21.
Attach the decals [A] [B] to the SPDF.
1.
Turn ON the main power.
2.
Set SP4-688-002 (Scan Image Density Adjustment 1-pass DF) to "101".
3.
Execute SP4-730-002 (FROM Main Factory Setting Execution ON/OFF).
4.
Check the vertical registration for the SPDF.
1. Create an original as shown in the following picture.
The large white arrow indicates the direction of feed.
SPDF DF3100 (D3B0)
2. Copy the original and make sure that the position of the line [A] is within 0±1mm
3. If not within the standard, adjust with the SP modes.
SP6-006-001 (ADF Adjustment Side-to-Side Regist: Front)
SP6-006-002 (ADF Adjustment Side-to-Side Regist: Rear)
5.
Check the horizontal registration for the SPDF.
1. Copy the original and make sure that the position of the line [B] that you wrote on the original
(see above) is within 0±2mm.
2. If not within the standard, adjust with the SP modes.
SP6-006-010 (ADF Adjustment L-Edge Regist (1-Pass): Front)
SP6-006-011 (ADF Adjustment L-Edge Regist (1-Pass): Rear)
6.
Check the skew.
1. Make sure that the difference between both end positions of the line [A] that you wrote on the original (see above) is within 0±2mm.
2. If not within the standard, change the position of the fixing screw [A] to the long hole [B] at the right hinge.
163
164
2. Installation
SP descriptions
SP4-688-002 (Scan Image Density Adjustment: 1-pass DF)
Adjusts density difference between Book and ADF. This SP is only for the SPDF models.
SP4-730-002 (FROM Main Factory Setting Execution ON/OFF)
Copies the parameters written in FROM in the SPDF to the engine board in the MFP. This SP is only for the SPDF models.
1 Bin Tray BN3110 (D3CQ)
No.
1 Tray
Description
2 1 Bin Tray Unit
3 Tray support bar
4 Harness
5 Gear
6 Screw: M3 x 8
7 Harness cover
8 Paper support guide
Q’ty
1
1
1
1
1
2
1
1
Remarks
Not used for this machine
165
166
2. Installation
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• When attaching this 1-bin tray unit at the same time as Bridge Unit BU3070 or Side Tray Type M3, attach this tray first. Otherwise, the 1-bin tray’s exit tray cannot be attached due to the Bridge Unit
BU3070 or Side Tray Type M3.
• To use together with the “Internal Finisher SR3130”, first attach the bottom plate of Internal Finisher
SR3130, and then install the 1-bin tray.
1.
Remove the orange tape and shipping retainers.
2.
Remove the accessories (fixing screws, etc.) provided with the machine.
3.
Open the right door, and then remove the small cover [A].
4.
Remove the screw and connector, and then remove the front upper cover [A].
1 Bin Tray BN3110 (D3CQ)
• Remember that there are three tabs at the positions of the red arrows.
• Tilt the operation panel [B] upward to a horizontal position, and then remove the front upper cover [A].
5.
Remove the paper exit tray [A].
6.
Remove the paper exit feeler [A].
167
168
2. Installation
7.
Open the front cover, and then remove the upper left cover [A] by pulling it towards the front ( ×1).
8.
Remove the left rear cover [A] ( ×2).
9.
Remove the inverter tray [A], and tray support rod cover [B] ( ×1).
1 Bin Tray BN3110 (D3CQ)
10.
Remove the paper exit cover [A] ( ×1).
169
170
2. Installation
11.
Attach the gear [A] provided with the accessories.
12.
Attach the 1-bin tray unit [A].
Make sure to engage it with the gear attached in the previous step.
Take care that the harness is not trapped between the 1-bin tray unit and the machine frame.
13.
Attach the harness provided with the accessories.
1 Bin Tray BN3110 (D3CQ)
14.
Attach the tray support bar [A] ( ×1).
When attaching the tray support bar [A], make sure that the harness attached in the previous step goes through the slit in the tray support bar circled in blue and comes outside of it as shown below.
15.
Hook the 1-bin tray [A] onto the 1-bin tray unit, aligning the positions in the blue circle.
171
2. Installation
16.
Connect the harness to the 1-bin tray, and bring it around.
17.
Insert the tray support bar firmly in the 1-bin tray, and attach the harness cover [A].
172
18.
Reattach the left rear cover, upper left cover and front upper cover, and close the right door.
19.
Reattach the paper exit tray and paper exit feeler.
20.
Turn ON the main power.
21.
Check that output to this tray can be selected on the operation panel, and check operation.
Check the following points for the paper exit feeler [A] at the paper exit.
• It can move in line with the ejection of paper
• It holds contact with the surface of the ejected paper and is still movable
1 Bin Tray BN3110 (D3CQ)
Paper will get jammed in the following cases.
• The paper exit feeler does not function due to obstacles (such as cables).
• The paper exit feeler does not function when the paper is pulled out and pushed back again.
173
2. Installation
No.
1
2
3
Tray Cover
Lever
Sheet
Description Q’ty
1
1 Not used for this machine
2
174
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• The internal shift tray cannot be used together with the following peripherals:
- Side Tray Type M3 (D725)
- Internal Finisher SR 3180 (D766)
- Internal Finisher SR 3130 (D690)
- Bridge Unit BU3070 (D685)
• To use together with the "1 Bin Tray BN3110 (D3CQ)", attach the "1 Bin Tray BN3110 (D3CQ)" first before installing the internal shift tray.
Internal Shift Tray SH3070 (D691)
1.
Remove the orange tapes, shipping retainers, and provided accessories (fixing screws, etc.).
2.
Attach the tray cover [B] to the shift tray [A].
3.
Remove the paper exit tray [A].
175
2. Installation
4.
Remove the connector cover [A].
5.
Attach the shift tray [A].
6.
Remove the paper exit feeler [A] to apply the Mylar sheet properly.
176
7.
Attach the sheets [A] at the edge of the paper exit cover.
• Make sure to attach the Mylar as shown in the photo below. This is to prevent curling when the paper lands in the tray.
Internal Shift Tray SH3070 (D691)
• The Mylar’s top edge should be 0-2.5mm from the top edge of the paper exit cover, i.e.
between the two red lines.
• The Mylar's side edge should be flush against the side of the cover, i.e. along the yellow dotted line.
8.
Reattach the paper exit tray and close the right door.
9.
Reattach the removed paper exit feeler [A].
10.
Do not use the lever supplied with the optional unit. Doing so may affect the stacking function.
11.
Turn ON the main power.
12.
Check that paper output to the shift tray can be selected at the operation panel, and check the operation.
Check the following points for the paper exit feeler [A] at the paper exit.
177
178
2. Installation
• It can move in line with the ejection of paper
• It holds contact with the surface of the ejected paper and is still movable
Paper will get jammed in the following cases.
• The paper exit feeler does not function due to obstacles (such as cables).
• The paper exit feeler does not function when the paper is pulled out and pushed back again.
No.
1
2
3
4
5
6
7
8
9
Left Extension Tray
Upper Extension Tray
Fixing Plate
Knob Screw
Tapping screw - M4 x 14
Tapping screw - M3 x 8
Bracket
Paper Support Guide
Driven Roller (Flat)
Description
Side Tray Type M3 (D725)
Q’ty
1
1
1
1
1
1
1
1
1
179
180
2. Installation
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• The side tray cannot be used together with the following peripherals:
- Internal Shift Tray SH3070 (D691)
- Bridge Unit BU3070 (D685)
- Internal Finisher SR 3180 (D766)
- Internal Finisher SR 3130 (D690)
• To use together with the "1 Bin Tray BN3110 (D3CQ)", attach the "1 Bin Tray BN3110 (D3CQ)" first before installing the side tray.
1.
Remove the orange tapes, shipping retainers, and accessories (fixing screws, etc.).
Side Tray Type M3 (D725)
2.
Remove the paper exit tray [A].
3.
Remove the paper exit feeler [A].
4.
Remove the driven roller [B] at the machine’s exit tray and attach the supplied driven roller [A].
• Insert a flathead screwdriver into the depression in the center, and then, lifting the driven roller, unlock the part indicated by the red arrow.
• When attaching the driven roller, push its center all the way in until it clicks.
181
2. Installation
182
[A]: The supplied driven roller has flat rollers.
[B]: The machine’s standard driven roller has drum-type rollers (as indicated by red frames).
5.
Attach the paper support guide [A] (Tab x4 ).
6.
Open the right door, and then remove the small cover [A].
Side Tray Type M3 (D725)
7.
Remove the screw and connector, and then remove the front upper cover [A].
• Remember that there are three tabs at the positions of the red arrows.
• Tilt the operation panel [B] upward to a horizontal position, and then remove the front upper cover [A].
183
2. Installation
8.
Attach the bracket [A].
9.
Remove the connector cover [A].
10.
Attach the bracket [A].
184
11.
Reattach the front upper cover, and close the right door.
12.
Attach the side tray unit [A] to the machine, and fix with a knob screw.
Side Tray Type M3 (D725)
13.
Attach the fixing plate [A] ( ×1).
14.
Attach the upper extension tray [A] and the left extension tray [B].
15.
Turn ON the main power.
185
186
2. Installation
16.
Check that paper output to the side tray can be selected at the operation panel, and check the operation.
No.
1
2
3
4
5
6
7
8
Tapping screw- M3 × 8
Screw - M4
Knob Screw - M4
Right Front Bracket
Upper Left Cover
Left Front Bracket
Paper Support Guide
Driven Roller (Flat)
Description
Bridge Unit BU3070 (D685)
Q’ty
1
1
1
1
1
1
1
1
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• The bridge unit cannot be used together with the following peripherals:
187
188
2. Installation
- Internal Shift Tray SH3070 (D691)
- Side Tray Type M3 (D725)
- Internal Finisher SR 3180 (D766)
- Internal Finisher SR 3130 (D690)
• To use together with the "1 Bin Tray BN3110 (D3CQ)", attach the "1 Bin Tray BN3110 (D3CQ)" first before installing the bridge unit.
1.
Remove the orange tapes, shipping retainers, and provided accessories (fixing screws, etc.).
2.
Remove the interval tray [A].
3.
Remove the paper exit tray [A].
4.
Remove the connector cover [A].
5.
Remove the paper exit feeler [A].
Bridge Unit BU3070 (D685)
189
2. Installation
6.
Remove the driven roller [B] at the machine’s exit tray and attach the supplied driven roller [A].
• Insert a flathead screwdriver into the depression in the center, and then, lifting the driven roller, unlock the part indicated by the red arrow.
• When attaching the driven roller, push its center all the way in until it clicks.
[A]: The supplied driven roller has flat rollers.
[B]: The machine’s standard driven roller has drum-type rollers (as indicated by red frames).
7.
Attach the paper support guide [A] (Tab x4 ).
190
8.
Open the front cover.
9.
Remove the upper left cover [A] ( ×1).
• The screw removed is used again in step 15.
Bridge Unit BU3070 (D685)
10.
Open the right door, and then remove the small cover [A].
11.
Remove the screw and connector, and then remove the front upper cover [A].
191
192
2. Installation
• Remember that there are three tabs at the positions of the red arrows.
• Tilt the operation panel [B] upward to a horizontal position, and then remove the front upper cover [A].
12.
Attach the right front bracket [A].
13.
Attach the bridge unit [A] to the machine.
Bridge Unit BU3070 (D685)
14.
Attach the front upper cover, and close the right door.
15.
Attach the upper left cover [A] provided with the accessories ( ×1).
16.
Attach the L type connecting bracket [A].
To fix the bridge unit securely on the machine, tighten the finisher's joint bracket [A] and L type connecting bracket [B] together when installing the finisher.
193
2. Installation
194
17.
Complete the bridge unit attachment. Refer to the procedure for connecting the optional
unit downstream of the bridge unit. page 195 "Booklet Finisher SR3220 (D3B9)"
18.
After the finisher is installed, turn ON the main power.
19.
Check that the finisher can be selected at the operation panel.
Booklet Finisher SR3220 (D3B9)
• To attach this optional unit, the following optional units are required.
- Bridge Unit BU3070 (D685)
- Paper Feed Unit PB3220/PB3210 (D787)
6
7
8
4
5
No.
1
2
3
Description
Shift Tray
Booklet Tray
Joint Bracket
Relay Guide Plate
Cushion
Tapping screws - M3 × 6
Tapping screw - M4 × 8
Screws - M4 × 12
9 Stabilizer
10 Ground Plate
11 Proof Support Tray
Installation Procedure: Arm
1
1
1
4
1
4
1
1
Q’ty
1
1
1
Remarks
1
This part must be attached to the finisher just after it is taken out of the shipping box.
195
2. Installation
196
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• Before installing this option, attach the "Bridge Unit BU3070 (D685)" and "Paper Feed Unit
PB3220/PB3210 (D797)".
• When you lift the finisher at the time of unpacking, do not hold the part [A]. Doing so may damage the frame.
Booklet Finisher SR3220 (D3B9)
1.
After unpacking, immediately attach the stabilizer [B] to prevent toppling.
Push it in thoroughly along the guide [A] until it clicks.
2.
Attach the ground plate [A] ( ×2).
197
198
2. Installation
3.
Remove the external orange tapes and shipping retainers.
4.
Open the front cover, and then remove the filament tape and packing materials.
5.
Remove the fixing bracket [A].
Booklet Finisher SR3220 (D3B9)
6.
Pull out the saddle stitch unit [A], and remove the filament tape and packing materials.
7.
Remove the accessories in the package (fixing screws, etc.).
8.
Attach the shift tray [A] ( ×1 : M4 × 8).
9.
Attach the booklet tray [A].
199
200
2. Installation
10.
Attach the relay guide plate [A] ( ×2).
11.
Clean the right side of the upper cover with a cloth moistened with alcohol, and then attach the cushion to the finisher.
• Make sure that the cushion is aligned with the front-lower edge [A] of the upper cover.
Booklet Finisher SR3220 (D3B9)
12.
Remove the connector cover [A] on the rear left side of the main machine.
13.
Attach the joint bracket [A] to the machine ( ×4 : 4x12).
Tighten the joint bracket [A] and bracket [B] of the bridge unit together.
• Attach the screw so that the screw head is at the center of the mark.
201
2. Installation
202
14.
Remove the screw on the connection lever [A] and pull the lever.
Booklet Finisher SR3220 (D3B9)
15.
Connect the finisher to the main unit, and then push in the connection lever [A] to fasten it to the main unit. ( x1)
16.
Connect the interface cable to the machine.
17.
Close the front cover.
18.
Turn ON the main power.
19.
Deliver some A3/DLT paper to the proof tray and check if the vertical registration is
20.
Check that the finisher can be selected on the operation panel, and check the finisher’s operation.
203
2. Installation
When using B4, LG or larger paper, or when using limp paper, the sheet may become kinked, resulting in premature full detection.
204
This can be solved by attaching the proof support tray [B] on the proof tray [A].
Problem that may occur after attaching this support tray:
When printing A4, LT or smaller paper with the support tray, the machine stacks only 200 sheets, which is less than the standard specification of 250 sheets.
When printing B4, LG or larger paper with the support tray, the machine stacks 50 sheets, which is the same as the standard specification.
• This Punch Unit is for the Booklet Finisher SR3220 (D3B9).
8
9
10
11
6
7
No.
1
2
3
4
5
Description
Punch unit
Cover
Stay
Hopper
Side-to-side detection unit
Punch unit movement motor unit
Hopper guide plate
Guide plate
Tapping screws - M3 × 6
Harness (Short)
Harness (Long)
Q’ty
1
1
1
1
1
Remarks
1
1
1
16
1
1 Not used for this machine
Punch Unit PU3050
205
2. Installation
206
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
1.
Take out of the box, and remove the orange tapes and shipping retainers.
2.
Pull out the finisher interface cable, and move it away from the machine.
3.
Remove the finisher rear cover [A] ( ×3).
4.
Open the top cover, and then remove the arm [A] ( ×1).
Punch Unit PU3050
5.
Open the finisher front cover, remove the three knobs ( x1).
• Knobs with a lock mechanism are removed using a knob screwdriver or similar while releasing the lock.
207
208
2. Installation
6.
Pull the saddle stitch unit [A] or stapling unit.
7.
Remove the finisher inner cover [A] ( ×3)
• Remove the connector at the back of the inner cover.
8.
Cut off part of the finisher inner cover [A].
9.
Remove the guide plate [A] ( ×4).
Punch Unit PU3050
10.
Insert and attach the hopper guide plate [A] from the front ( ×4).
At this time, pass the harness [B] through the clamp [C].
209
2. Installation
210
11.
Attach the stay [A] ( ×3).
Front [B]: Insert the holes in the stay over the embossed parts on the finisher.
Rear [C]: Place the axis of the stay through the notch in the finisher.
12.
Insert and attach the guide plate [A] from the rear ( ×2).
Punch Unit PU3050
13.
Insert and attach the side-to-side detection unit [A] from the rear ( ×2).
Front: The two shafts of the unit are passed through bearings in the finisher.
211
212
2. Installation
Punch Unit PU3050
14.
Connect the harness [A] of the hopper guide plate to the relay connector [B] of the sideto-side detection unit, and then clamp the harness.
15.
Insert and attach the punch unit [A] from the rear.
213
214
2. Installation
16.
Attach the punch unit movement motor unit [A] so that the gear [B] meshes firmly ( ×2).
17.
Insert the hopper [A].
Punch Unit PU3050
18.
Connect the provided harness to the punch unit board [A] and the control board [B] of the finisher ( ×6).
215
216
2. Installation
19.
Remove the harness [A] from the clamp [B], and connect it to the punch unit board [C]
( ×1).
20.
Connect the harness [A] of the side-to-side detection unit to the relay connector [B] of the harness ( ×1).
Punch Unit PU3050
21.
Connect the harness [A] of the punch unit movement motor unit to the punch unit board
[B] ( ×1).
22.
Attach the supplied cover [A] to the punch unit board.
217
218
2. Installation
23.
Clamp the harnesses.
24.
Reattach the finisher rear cover.
25.
Reattach the finisher inner cover and three knobs.
26.
Close the front cover.
27.
Close the top cover.
28.
Reconnect the finisher to the machine, and connect the interface cable.
29.
Turn ON the main power.
30.
Check that the punch can be selected at the operation panel, and check the operation.
Internal Finisher SR3130 (D690)
No.
1
2
3
4
5
-
-
-
6
7
8
-
Description
Staple Cartridge
Front Right Cover
Bottom Plate
Left Lower Cover
Entrance Guide Plate
Stabilizer
Paper Support Guide
Driven Roller (Flat)
Screw - M3 × 6
Tapping Screw – M4 x 6
Decal - EMC Address
Notes on Installing the Optional Unit
1
1
1
2
1
1
6
Q’ty
1
1
1
1
1
Remarks
Not used when the punch unit is attached.
219
220
2. Installation
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• This option cannot be used together with the following peripherals:
- Internal Shift Tray SH3070 (D691)
- Side Tray Type M3 (D725)
- Internal Finisher SR 3180 (D766)
- Bridge Unit BU3070 (D685)
• To use together with the "1 Bin Tray BN3110 (D3CQ)", after attaching the bottom plate of this option, attach the "1 Bin Tray BN3110 (D3CQ)", and then install this option.
• To use together with the "Punch Unit PU3040 (D716)", first attach the "Punch Unit PU3040
(D716)" before installing this option.
1.
Remove the orange tapes and shipping retainers.
2.
Remove the package accessories (fixing screws, etc.).
Internal Finisher SR3130 (D690)
3.
Remove the paper exit tray [A].
4.
Remove the paper exit feeler [A].
5.
Open the front cover, and then remove the upper left cover [A] ( ×1).
221
2. Installation
6.
Remove the left rear cover [A] ( ×2).
7.
Remove the inverter tray [A], and tray support plate [B] ( ×1).
222
8.
Open the right door, and then remove the small cover [A].
Internal Finisher SR3130 (D690)
9.
Remove the screw and connector, and then remove the front upper cover [A].
• Remember that there are three tabs at the positions in the red arrows.
• Tilt the operation panel [B] upward to a horizontal position, and then remove the front upper cover [A].
10.
Remove the paper exit cover [A] ( ×1).
223
224
2. Installation
11.
Remove the connector cover [A].
12.
Remove the paper exit lower cover [A].
13.
Remove the upper rear inner cover [A] ( ×2)
14.
Install a screw removed in step 12.
Internal Finisher SR3130 (D690)
225
2. Installation
15.
While pressing the bottom plate [A] into the area shown by the blue circle [B], insert it into the slot shown by the blue circles [C] [D].
226
• The following procedure is the easiest way to set this component.
1) Slip the bottom plate [A] into the position in the blue circle [B].
2) Insert the bottom plate [A] into the hole in the blue circle [C].
3) When the bottom plate [A] is picked up (see below), it can be inserted into the hole in the blue circle [D].
Internal Finisher SR3130 (D690)
16.
Attach the bottom plate [A] ( ×3)
17.
Attach the upper rear inner cover.
18.
Attach the paper exit cover.
19.
Reattach the connector cover, front upper cover, and then close the right door.
20.
Remove the driven roller [B] at the machine’s exit tray and attach the supplied driven roller [A].
• Insert a flathead screwdriver into the depression in the center, and then, lifting the driven roller, unlock the part indicated by the red arrow.
• When attaching the driven roller, push its center all the way in until it clicks.
227
2. Installation
[A]: The supplied driven roller has flat rollers.
[B]: The machine’s standard driven roller has drum-type rollers (as indicated by red frames).
21.
Attach the paper support guide [A] (Tab x4).
228
• Up to this point, the procedure is the same as punch unit installation (for fitting the punch unit, refer to Step 3 and later of the Punch unit installation procedure).
Internal Finisher SR3130 (D690)
22.
Slide the finisher front right cover [A] from left to right to attach it ( ×1).
23.
Reattach the inverter tray.
24.
Attach the entrance guide plate [B] to the finisher [A] ( ×2).
229
2. Installation
25.
Slide the finisher [A] along the rail of the bottom plate from the left-hand side of the machine to attach it ( ×1).
230
• Hold the front side [A] of the internal finisher as shown below to check if the internal finisher is correctly set in the rail of the bottom plate.
26.
Reattach the left rear cover.
Internal Finisher SR3130 (D690)
27.
Insert the upper left cover [A] from the front, and slide it to reattach it.
28.
Attach the stabilizers.
• Because the weight is biased to the right of the machine if the internal finisher is installed, stabilizers are required on the left side. Because they are included with the finisher, install these stabilizers at the same time as you install the internal finisher.
231
2. Installation
29.
Remove the connector cover, then connect the interface cable to the machine.
30.
Move the stapler unit forward, then set the staple cartridge [A].
232
31.
Reinstall the stapler unit, and then turn ON the main power.
32.
Check that the finisher can be selected at the operation panel, and check the finisher operation. Also when the punch unit is installed, check the punching operation.
Punch Unit PU3040 (D716)
• Punching unit for the Internal Finisher SR3130 (D690).
-
-
-
No.
1
2
3
4
5
Description
Hopper
Punch Unit Cover
Lower Front Cover
Lower Rear Cover
Holder
Knob Screw - M4
Tapping screws - M3x 6
Decal - EMC Address
1
3
1
Q’ty
1
1
1
1
1
Remarks
233
234
2. Installation
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• When supplied together with the "Internal Finisher SR3130", attach this option before installing the
"Internal Finisher SR3130"
• If the "Internal Finisher SR3130" is already attached, attach this option after removing the finisher.
1.
Take out from the box, and remove the filament tape and packing material.
2.
Remove the finisher and finisher front right cover from the machine.
3.
Perform steps 1 to 21 of the installation procedure for the "Internal finisher
SR3130".
page 219 "Internal Finisher SR3130 (D690)"
4.
Change the fixing position of the bracket [A] of the bottom plate ( ×1).
Punch Unit PU3040 (D716)
5.
Replace the lock holder of the bottom plate with the lock holder [A] ( ×1) provided with the accessories.
6.
Reattach the front upper cover.
7.
Pass the shafts [B] of the punch unit [A] through the bearings [C] of the bottom plate, and attach to the machine ( ×1, knob screw).
If it is difficult to insert by probing, look from the side while you insert it into the bearings of the bottom plate.
235
236
2. Installation
Punch Unit PU3040 (D716)
8.
When installing the punch unit in a finisher that is already installed, remove the relay guide plate [A] ( ×2).
• This step is unnecessary when installing the finisher and punch unit at the same time.
9.
Attach the punch unit cover [A] provided with the accessories, inserting the tabs ( ×1).
237
238
2. Installation
10.
Insert the hopper [A].
11.
Slide the finisher [A] along the rail of the bottom plate from the left-hand side of the machine to attach it ( ×1).
12.
Attach the components [A] and [B] to the finisher ( ×2).
13.
Attach the left rear cover.
14.
Insert the upper left cover [A] from the front, and slide it to attach it.
Punch Unit PU3040 (D716)
15.
Attach stabilizers.
• Because the weight is biased to the right of the machine if the internal finisher is installed, stabilizers are required on the left side. Because they are included with the finisher, install these stabilizers at the same time as you install the internal finisher.
239
2. Installation
16.
Remove the connector cover, then connect the interface cable to the machine.
17.
Move the stapler unit forward, then set the stapler [A].
240
18.
Turn ON the main power.
19.
Check that the finisher can be selected at the operation panel, and check the finisher and punch operation.
Internal Finisher SR3180 (D766)
No.
1 Bottom Plate
Description
2 Left Lower Cover
3 Paper Exit Tray
4 TAPPING SCREW:3x8
5 TAPPING SCREW:3x8
6 TAPPING SCREW:3x8
7 SCREW:M3x6
8 TAPPING SCREW:3x6
9 TAPPING SCREW:4x8
10 Slide Rail
11 Nylon Clamp
12 Paper Support Guide
13 Driven Roller (Flat)
Q’ty
1
1
1
2
2
2
3
1
1
1
1
1
1
Remarks
241
2. Installation
242
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• This option cannot be used together with the following peripherals:
- Internal Shift Tray SH3070 (D691)
- Side Tray Type M3 (D725)
- Internal Finisher SR 3130 (D690)
- Bridge Unit BU3070 (D685)
• For using this option together with "1 Bin Tray BN3110 (D3CQ)", attach the bottom plate of this option at the beginning, then install the "1 Bin Tray BN3110 (D3CQ)", followed by installing this option.
1.
Remove the orange tapes and shipping retainers.
Internal Finisher SR3180 (D766)
2.
Remove the knob screw and red tag [A].
3.
Remove the shaft [B] from the slide rail [A] ( x 1).
243
244
2. Installation
4.
Remove the paper exit cover [A] ( x 2).
5.
Place the slide rail [A] under the internal finisher [B].
6.
Insert the shaft [A] into the holes located in the slide rail and internal finisher, and then fasten with the screw ( x 1).
7.
Attach the paper exit cover (removed in step 4) [A] ( x 2).
Internal Finisher SR3180 (D766)
8.
Remove the paper exit tray [A].
9.
Remove the paper exit feeler [A].
245
246
2. Installation
10.
Open the front cover, and then remove the left upper cover [A] ( x 1).
11.
Remove the left rear cover [A] ( x 2).
12.
Remove the inverter tray [A] and tray support plate [B].
Internal Finisher SR3180 (D766)
13.
Open the right door, and then remove the small cover [A].
14.
Remove the screw and connector, and then remove the front upper cover [A].
247
248
2. Installation
• Remember that there are three tabs at the positions of the red arrows.
• Tilt the operation panel [B] upward to a horizontal position, and then remove the front upper cover [A].
15.
Remove the paper exit cover [A] ( x 1).
16.
Remove the connector cover [A].
Internal Finisher SR3180 (D766)
17.
Remove the paper exit lower cover [A].
• The lower inside cover can be removed together with the paper exit lower cover, since the inside cover is secured on the paper exit lower cover with two screws.
249
250
2. Installation
18.
Remove the lower inside cover [B] from the paper exit lower cover [A] ( x 2).
19.
Remove the upper inside cover [A] ( x 2).
20.
Insert the bottom plate [A] into the holes.
21.
Install the bottom plate [A] ( x 3, Accessory No. 7).
Internal Finisher SR3180 (D766)
22.
Install the lower inside cover (removed in step 18) [A] in the finisher ( x 2, Accessory
No.5).
23.
Reattach the upper inside cover (removed in step 19) [A] ( x 2).
251
2. Installation
24.
Reattach the tray support plate (removed in step 12) [A].
25.
Reattach the paper exit cover (removed in step 15 and step 16) [A] and the connector cover [B].
Touching the moving parts inside of the cover can result in an injury. To avoid this, be sure to install the connector cover [B].
252
26.
Reattach the front upper cover (removed in step 14) and then close the right door.
27.
Remove the driven roller [B] at the machine’s exit tray and attach the supplied driven roller [A].
• Insert a flathead screwdriver into the depression in the center, and then, lifting the driven roller, unlock the part indicated by the red arrow.
• When attaching the driven roller, push its center all the way in until it clicks.
Internal Finisher SR3180 (D766)
[A]: The supplied driven roller has flat rollers.
[B]: The machine’s standard driven roller has drum-type rollers (as indicated by red frames).
28.
Attach the paper support guide [A] (Tab x 4).
253
254
2. Installation
29.
Install the internal finisher [A].
30.
Secure the finisher ( x 1, Accessory No.8).
31.
Reattach the left rear cover [A]
32.
Reattach the left upper cover [A].
Internal Finisher SR3180 (D766)
33.
Attach the left lower cover [A] ( x 2, Accessory No.6).
255
256
2. Installation
34.
Attach the paper exit tray [A] ( x 2, Accessory No.4).
35.
Reattach the inverter tray [A] removed in step 12.
36.
Remove the connector cover [A] (Release the tab).
Internal Finisher SR3180 (D766)
37.
Connect the interface cable [A].
38.
Attach the nylon clamp [A] as shown below ( x 1, Accessory No.9).
39.
Turn ON the main power.
257
258
2. Installation
40.
Ensure that the operation panel displays finisher jobs properly and that it works properly.
• To adjust the strength of the crimp between sheets of stapled paper, there is a setting to select either single or double stapling.
• The crimp is weakened when there is an image (toner) at the point which is to be stapled. There also is a setting to mask the image on the point for stapling, in order to prevent the crimp from being weakened.
• Depending on users demands, explain the settings/methods of the settings by checking the following instructions.
Use this procedure to select the type of stapling that is done by the stapleless stapler.
Note that if you change the finisher type from Finisher SR3210 to Internal Finisher SR3180, which has the same type of stapleless staple unit, the current setting in [Stapling Method for Stapleless Stapler] is not carried over, so configure the setting again.
1.
Press the [User Tools] icon on Home screen.
2.
Press [Machine Features] > [System Setting] > [General Setting] >[Stapling Method for
Stapleless Stapler].
3.
Select [Double] or [Single].
1.
Press the [User Tools] icon.
2.
Press [Machine Features] > [System Setting] > [General Setting].
3.
Press [Erase Margin for Stapleless Stapler].
Internal Finisher SR3180 (D766)
259
2. Installation
No.
1 Main Tray
2 Lock Plate
3 Sub Tray
4 Rivet
Description
1
1
Q’t y
1
2
Remarks
260
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• Be careful not to get your finger caught in the area indicated by the red frame (the tray’s rotating and insertion part).
Banner Paper Guide Tray Type M19 (D3BF)
1.
Open the bypass tray, and then attach the sub tray [A]. (Rivet x2)
2.
Fold the sub-tray.
3.
While pressing down the feeler [B] on the bypass tray, push the main tray [A] into the bypass tray to attach it.
When you attach the tray, hold it with both hands to make sure that it does not fall.
261
262
2. Installation
• Check if the locks on the main tray’s sides are engaged.
4.
Attach the belt by engaging it with the hooks [A].
Banner Paper Guide Tray Type M19 (D3BF)
5.
Remove the backing paper for the double-sided tapes on the lock plate.
6.
Stick the lock plate [B] with its center aligned with the indentation [A] on the right door.
263
264
2. Installation
7.
Tuck in the banner paper guide tray [A].
• The double-sided adhesive tapes stick firmly in about one day.
• When replacing the parts of the Banner Paper Guide Tray, use the installation procedure above in reverse order as a reference in order to make it easier to disassemble the unit.
Imageable Area Extension Unit Type M19 (D3BR-07)
No.
Description
1 Paper transfer roller (Extended)
Q’ty
1
Remarks
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• Do not touch the roller surface during replacement. Also, when taking out the unit from the box, be careful not to touch the roller surface [A].
265
2. Installation
1.
Enter the SP mode.
2.
Set SP2-400-001(Paper Transfer Roller Settings Width of Paper Transfer Roller) to "1”.
• When SP2-400-001 is changed over, a message is displayed stating "Switch the power
OFF/ON".
3.
After the SP is changed, turn OFF the main power.
4.
Replace the roller [A].
For details about how to replace the roller, refer to page 491 "Paper Transfer Roller".
266
• During PM replacement, do not install the wrong type of roller.
Imageable Area Extension Unit Type M19 (D3BR-07)
• [A]: The standard roller has a gray collar at its end.
• [B]: Imageable Area Extension Unit Type M19 does not have a collar on it.
5.
Turn ON the main power.
6.
Using SRA3 paper, check that a full-bleed halftone image is output, and that the image extends to 315 mm in width.
SP descriptions
• SP2-400-001 (Paper Transfer Roller Settings)
Specifies the width of the Paper Transfer Roller. This SP must be set to "1" when Imageable Area
Extension Unit Type M19 is installed.
0: Default roller
1: Wide roller
The following problems occur.
When a change-over was made from a standard roller to the imaging range extension option
(If the SP setting is the normal setting (SRA3 paper not supported), but the optional longer paper transfer roller is installed)
• The image cannot be correctly transferred to the SRA3 paper area.
• The MUSIC/program control pattern adheres to the ends of the paper transfer roller (outside the A3 area), and this can transfer to the underside of printouts.
• Real-time process control cannot be performed correctly, and an abnormal image and
SC285-00 (MUSIC error) may occur.
When a change-over was made from the imaging range extension option to a standard roller
(If the SP setting is for SRA3, but the paper transfer roller is the normal one (SRA3 paper not supported))
267
268
2. Installation
• Real-time process control is not performed, and the interval between process controls becomes short.
• The waiting time for fusing temperature rise is longer than intended.
External Keyboard Bracket Type M19 (D3BR-10)
No.
Description
1 Keyboard table bracket
2 Keyboard stand bracket
3 Keyboard stand
4 Screw: M4 x 12
5 Screw: M3 x 8
6 Screw: M3 x 12
Q’ty
1
1
2
2
4
1
Remarks
• This optional unit is not supplied with a keyboard. Use a commercially available keyboard.
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
269
270
2. Installation
1.
Open the right door, and then remove the small cover [A].
2.
Remove the screw and connector, and then remove the front upper cover [A].
• Remember that there is a tab at the positions of the red arrows.
• Rotate the operation panel [B] upward to a horizontal position, and then detach the front upper cover [A].
3.
Remove the screw [A] on the frame of the machine.
External Keyboard Bracket Type M19 (D3BR-10)
4.
Make 3 screw holes in the front upper cover.
5.
Reattach the front upper cover to the machine.
271
272
2. Installation
6.
Attach the keyboard stand bracket [A] on the front upper cover ( x3).
7.
Attach the keyboard stand [A] on the keyboard stand bracket ( x4).
8.
Place a keyboard on the keyboard stand, and then pass the keyboard cable through the hole in the keyboard stand.
9.
Remove the rear cover [A].
10.
Remove the scanner right cover [A] ( ×1)
External Keyboard Bracket Type M19 (D3BR-10)
11.
Route the keyboard cable [A] along the right side of the scanner unit as shown below.
12.
Route the keyboard cable along the rear side of the scanner unit ( x1).
• Adjust the keyboard cable by making loops if the keyboard cable has too much slack.
273
274
2. Installation
13.
Remove the cutout [A] in the left rear cover to make a cable hole, and then pass the keyboard cable [B] through it.
14.
Connect the keyboard cable to the USB slot.
15.
Reattach the scanner right cover, and rear cover.
16.
Close the right door.
Internal Options
[A]
[B]
[C]
Slot
USB mini
USB port
I/F slot
*2
Option
Used for the PictBridge function.
• Bluetooth Interface Unit Type D (D566)
• Smart Card Reader Built-in Unit Type M19 (D3BS-22)
• NFC Card Reader Type M19 (D3BS-21)
• External Keyboard Bracket Type M19 (D3BR-10)
• USB Device Server Option Type M19 (D3BC-28, -29)
• Extended USB Board Type M19 (D3BS-01)
• IEEE 1284 Interface Board Type M19 (D3C0)
• File Format Converter Type M19 (D3BR-04)
• IEEE 802.11a/g/n Interface Unit Type M19 (D3BR-01)
• RC-GATE
Fax Option Type M19 (D3BV-01) [D] I/F slot
*1
*1 Dedicated slot for fax unit
*2 There is no difference between the left and right USB port.
275
2. Installation
No
1 USB Cable
2 Interface Board
3 Ferrite Core
4 Cable Ties
Items Q’ty
1
1
2
2
Remarks
276
• An Ethernet cable is not packed with this option.
USB Device Server Option Type M19 (D3BC-28,-29)
No.
1
2
3
Item
Switch
Ethernet port
USB port
Description
Used to reset to the factory settings.
Used to connect the Ethernet cable.
Used to connect this option to the main machine.
Do not use this port with other options.
• When installing the USB device server option, make sure that the labels 'USB-A' and 'Ethernet' are upside down.
277
278
2. Installation
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• The USB device server option has an IP address stored on the PCB. This is different from the machine's IP address. The IP address and other network settings of the USB device server option must be configured after installing this option.
1.
Turn OFF the main power of the machine, and unplug the power cord from the wall socket.
2.
Remove the slot cover [A].
3.
Insert the interface board [A] into the I/F slot.
4.
Remove the I/F cover [A].
USB Device Server Option Type M19 (D3BC-28,-29)
5.
Cut off the USB port cover [A] with nippers or other such tool.
6.
Reattach the I/F cover.
7.
Insert the USB cable [A] into the USB port (Type A) on the machine I/F.
8.
Insert the other side of the USB cable [B] into the USB port (Type B) on this option board.
279
2. Installation
9.
Attach the ferrite cores to the Ethernet cable, while looping the cable at 3 cm (approx. 1.2
inch) [A] from the each end of the cable.
280
10.
Only for installing this option in North America, bind both cores with cable ties [A] as shown below.
The two binds are not included in options produced before March, 2015. To bind the cores, use the binds registered as service parts or similar ones.
USB Device Server Option Type M19 (D3BC-28,-29)
11.
Insert the Ethernet cable [A] into the Ethernet port on this option.
12.
Insert the other end of the Ethernet cable to a PC for network setting.
13.
Plug the power cord into the wall socket and turn on the main power of the machine.
• Do not unplug the USB cable while the machine is recognizing this option. It may take between 30 seconds to 1 minute to finish recognizing it (the LEDs on the Ethernet port of this option light up after recognizing this option; see below). If unplugged, connect the cable again.
14.
Make sure that the machine recognizes this option correctly by doing one of the following:
1. Access the option’s IP address from a web browser.
2. Ping the option’s IP address from a command prompt on a Windows PC in the same network as the mainframe.
If the IP address cannot be found (DHCP server), use the MAC address. This is the number printed on the seal attached to the printed circuit board for the USB server.
3. Use "RX" + the option’s MAC address and access a web browser.
281
282
2. Installation
Example: http://RX0080926A3264
4. Ping "RX" + "MAC address" from the command prompt on a windows PC which is on the same network as the mainframe.
• When installing the USB Device Server Option Type M19, the installation status is not shown on the
Configuration Page.
• The customer should keep the slot cover which were removed.
When this option is properly installed and recognized by the main machine, the LED indicators light up under the following conditions.
USB Device Server Option Type M19 (D3BC-28,-29)
No.
1
2
3
Light Color
Green and Yellow 1000BASE-T operates
Green 10BASE-T operates
Yellow 100BASE-TX operates
Lights Up When:
This section describes how to set an IP address on this option manually. Note that you can set an IP address which is not only on the same network segment but also on a different network segment to share a single printer with devices in multiple networks.
• You cannot change the IP address for this option from the operation panel of the main machine.
The setting must be done from a web browser on your PC.
• The network setting of this option is initially assigned as follows:
IP address: 192.168.100.100 / Subnet mask: 255.255.255.0
• The network setting of your PC must be in the same network segment to change the network setting of this option.
1.
Make a note of the current network settings of your PC.
2.
Change the IP address on your PC to [192.168.100.xxx (*0 - 255)].
3.
Change the subnet mask on your PC to [255.255.255.0].
4.
Open a web browser.
5.
Type [http://192.168.100.100/] in the address bar.
6.
Press the "Enter" key.
• The setting screen for this option appears.
283
2. Installation
7.
Click [Network Setting].
8.
Type [root] in the user name textbox and click [OK].
9.
Input [IP Address], [Subnet Mask] and [Default Gateway].
284
10.
Set other items if needed.
11.
Press [Set]
12.
Close the web browser.
13.
Disconnect the Ethernet cable from the PC.
14.
Connect the Ethernet cable to a network device (e.g. switching hub).
15.
Set the IP address of this option in the printer driver which you use.
Extended USB Board Type M19 (D3BS-01)
No
1 Extended USB Board
Items Q’ty
1
Remarks
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• Do not put your hand into the controller box. It will result in a malfunction or injury.
• Before doing any work, touch a metal object to discharge static electricity from the body.
285
286
2. Installation
1.
Remove the slot cover [A].
2.
Insert the Extended USB Board into the I/F slot.
3.
Turn ON the main power.
4.
Check that the system settings list is output, and that the board is recognized correctly.
• The customer should keep the slot cover which were removed.
IEEE 1284 Interface Board Type M19 (D3C0)
No.
1
2
3
Description
IEEE 1284 Interface Board
FCC document
Notes for users
Q’ty
1
1
1
Remarks
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• Do not put your hand into the controller box. It will result in a malfunction or injury.
• Before doing any work, touch a metal object to discharge static electricity from the body. There is a possibility that the IEEE 1284 Interface Board may malfunction due to static electricity.
287
288
2. Installation
1.
Remove the slot cover [A].
2.
Insert the IEEE 1284 Interface Board into the I/F slot.
3.
Turn ON the main power.
4.
Check that the system settings list is output, and that the board is recognized correctly.
• The customer should keep the slot cover which were removed.
IEEE 802.11agn Interface Unit Type M19 (D3BR-01)
This option is not available in China, Taiwan, and Korea.
No.
1
2
3
4
IEEE802.11a/g/n Unit
Clamps
Velcro Fasteners
Notes for Users
Description Q’ty
1
2
8
2
• Since disassembly/alteration of a wireless LAN board is illegal, during service replacements, replace the whole PCB assembly.
• Be sure to give the provided leaflet to the customer.
289
290
2. Installation
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• Do not put your hand into the controller box. It will result in a malfunction or injury.
• Before doing any work, touch a metal object to discharge static electricity from the body. There is a possibility that the extension wireless LAN board may malfunction due to static electricity.
• When using wireless LAN (IEEE802.11 b/g/n:2.4-GHz band), this radio product uses the 2.4-
GHz band. Check that industrial, scientific and medical devices using the same frequency bands, such as a microwave oven or a cordless telephone, are not used nearby.
• If there is interference, communication may become unstable. Check that there are no devices likely to cause interference in the surrounding area.
1.
Remove the slot cover [A].
IEEE 802.11agn Interface Unit Type M19 (D3BR-01)
2.
Insert the extended wireless LAN board [A] into the slot ( ×2)
• Press the extended wireless LAN board firmly in, and check it is firmly connected.
• The customer should keep the slot cover which were removed.
1.
Attach the velcro fastener [B] (provided with the accessories) on the antenna [A].
291
2. Installation
2.
Peel the backing paper off the velcro fastener, and attach the antenna on the rear cover and scanner left cover as shown ( x4).
292
• Take care to loop it around so that it does not interfere with other options or I/F cables.
3.
Turn ON the main power.
4.
Check that the system settings list is output, and the option is recognized correctly.
Go into the User Tools mode and do the procedure below. These settings take effect every time the machine is powered on.
• IEEE 802.11a/g/n function is disabled while using Ethernet.
1.
Press the "User Tools" icon.
2.
Press "Machine Features" > "System Settings".
• Select "Interface Settings"> "Network" > "LAN Type". The "LAN Type" (default: Ethernet) must be set for either Ethernet or wireless LAN.
3.
Select "Interface Settings"> "Wireless LAN". Only the wireless LAN options show.
4.
Set the "Communication Mode".
5.
Enter the "SSID setting". (The setting is case sensitive.)
6.
Set the "Ad-hoc Channel". You need this setting when Ad Hoc Mode is selected. The allowed range for the channel settings may vary for different countries.
• For mainly Europe and Asia
2,412 - 2,462 MHz (1 - 11 channels)
IEEE 802.11agn Interface Unit Type M19 (D3BR-01)
5,180 - 5,240 MHz (36, 40, 44 and 48 channels)
(default: 11)
• In some countries, only the following channels are available: 2,412 - 2,462 MHz (1 - 11 channels)
• For mainly North America
2,412 – 2,462 MHz (1 - 11 channels)
5,180 – 5,240 MHz (36, 40, 44 and 48 channels)
(default: 11)
7.
Set the "Security Method" to specify the encryption of the Wireless LAN.
• The "WEP" (Wired Equivalent Privacy) setting is designed to protect wireless data transmission. The same WEP key is required on the receiving side in order to unlock encoded data. There are 64 bit and 128 bit WEP keys.
• Range of Allowed Settings:
64 bit: 10 characters
128 bit: 26 characters
• Specify "WPA2" when "Communication Mode" is set to "Infrastructure Mode". Set the "WPA2
Authent. Method".
• WPA2 Authent. Method:
Select either "WPA2-PSK" or "WPA2".
If you select "WPA2-PSK", enter the pre-shared key (PSK) of 8-63 characters in ASCII code.
When "WPA2" is selected, authentication settings and certificate installation settings are required.
8.
Press "Wireless LAN Signal" to check the machine's radio wave status using the operation panel.
• Press "Restore Factory Defaults" to initialize the wireless LAN settings.
The following SP commands and UP modes can be set for IEEE 802.11
SP No.
Name
SP5-840-006 Channel MAX
Function
Sets the maximum range of the channel settings for the country.
293
294
2. Installation
SP No.
Name
SP5-840-007 Channel MIN
SP5-840-008
Transmission
Speed
SP5-840-011 WEP Key Select
Name
SSID
WEP Key
UP mode
WEP Mode
WPA2 Authent.
Method
Function
Sets the minimum range of the channels settings allowed for your country.
Sets the transmission speed.
Auto, 54 Mbps, 48 Mbps, 36 Mbps, 24 Mbps, 18 Mbps, 12
Mbps, 9 Mbps, 6 Mbps, 11 Mbps, 5.5 Mbps, 2 Mbps, 1
Mbps (default: Auto).
Used to select the WEP key (Default: 00).
Function
Used to confirm the current SSID setting.
Used to confirm the current WEP key setting.
Used to show the maximum length of the string that can be used for the WEP Key entry.
Used to confirm the current WPA authentication setting and preshared key.
File Format Converter Type M19 (D3BR-04)
No.
1
2
File Format Converter
Notes for Users
Description Q’ty
1
1
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• Do not put your hand into the controller box. It will result in a malfunction or injury.
• Before doing any work, touch a metal object to discharge static electricity from the body. There is a possibility that the board may malfunction due to static electricity.
295
296
2. Installation
1.
Remove the slot cover [A].
2.
Insert the file format converter board into the I/F slot.
3.
Turn ON the main power.
4.
Check the system settings list is output, and that the option is recognized correctly.
• The customer should keep the slot cover which were removed.
Bluetooth Interface Unit Type D (D566-01)
No.
1
-
Bluetooth Module
CD-ROM
Description Q’ty
1
2
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
• Do not put your hand into the controller box. It will result in a malfunction or injury.
1.
Attach the BT wireless interface to the USB-A slot [A].
There is no difference between the left and right USB ports.
2.
Turn ON the main power.
297
298
2. Installation
3.
Check the system settings list is output, and that the option is recognized correctly.
Memory Unit Type M19 4GB (D3BX-03)
No.
Description
1 Memory Unit (DDR3L-DIMM 4G)
Q’ty
1
Remarks
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
1.
Remove the rear cover [A].
299
2. Installation
2.
Remove the controller box cover [A].
Red Circle: Remove / Blue Circle: Loosen
3.
Release the latches and remove the standard 2GB DIMM [A].
4.
Insert the Memory Unit Type M19 4GB [A] into the SDRAM socket.
Push the release latches [B] until they slip into the notch on the edge of the SDRAM.
300
5.
Reattach the controller box cover and rear cover.
6.
Turn ON the main power.
Memory Unit Type M19 4GB (D3BX-03)
7.
Print out the system setting list to make sure that the memory unit is recognized properly.
301
2. Installation
No.
1
-
Description
Enhanced Security HDD
EMC Address
Q’ty
1
1
Remarks
302
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
1.
Remove the rear cover [A].
Enhanced Security HDD Option Type M12 (D3A6-02)
2.
Remove the controller box cover [A].
Red Circle: Remove / Blue Circle: Loosen
3.
Remove the standard HDD [A] installed on the machine.
303
304
2. Installation
4.
Separate the standard HDD from the bracket.
5.
Disconnect the cables from the standard HDD. ( × 2)
Enhanced Security HDD Option Type M12 (D3A6-02)
6.
Remove the enhanced security HDD from its protective pack.
7.
Connect the two cables to the enhanced security HDD. ( × 2)
8.
Fasten the HDD to the bracket. ( × 4)
9.
Install the HDD bracket in the controller box.
10.
Reassemble the machine.
305
2. Installation
1.
Connect the power cord and turn the machine on. A message prompts you to format the hard disk.
2.
Touch [Format].
3.
Wait for the machine to finish formatting the hard disk.
• Do not touch the power switch while the hard disk format is in progress. Wait for the machine to tell you that the formatting is finished.
306
4.
Turn the main power OFF and back ON again after the message tells you formatting is finished.
5.
Enter the SP mode.
Enhanced Security HDD Option Type M12 (D3A6-02)
6.
Do SP5-846-040 to copy the address book to the hard disk from the controller board.
7.
Do SP5-846-041 to let the user get access to the address book.
8.
Turn the main power OFF and back ON again.
9.
Ask an administrator to register an HDD authentication code in the machine.
• If the HDD Authentication Code is not registered, the function of the enhanced security HDD is not activated.
SP descriptions
SP5-846-040
SP5-846-041
UCS Setting: Addr Book Migration(USB->HDD)
Copies the address book to the hard disk from the controller board.
[Execute]
UCS Setting: Fill Addr Acl Info
This SP must be executed immediately after installation of an HDD unit in a basic machine that previously had no HDD. The first time the machine is powered on with the new HDD installed, the system automatically takes the address book from the
NVRAM and writes it onto the new HDD. However, the new address book on the
HDD can be accessed only by the system administrator at this stage. Executing this
SP by the service technician immediately after power on grants full address book access to all users.
[Execute]
307
308
2. Installation
No.
1
2
3
4
5
6
7
Description
PCB: MKB
Harness IOB to MKB
Screws M3x8
Screws M3x6
Standoffs
Clamp
Wire Band
Q’ty
1
1
2
4
4
1
1
For This Model
Not used
Not used
Not used
Not used
Not used
Optional Counter Interface Unit Type M12 (B870-21)
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
1.
Remove the rear cover [A].
2.
Remove the controller box cover [A].
Red Circle: Remove / Blue Circle: Loosen
309
310
2. Installation
3.
Attach the studs provided with the option on the helmholtz silencer (Stud ×4).
4.
Attach the counter interface board [A].
5.
Connect the harness [A] of the MFP to the white connector (13 pins) [B].
• Do not use the harness that is provided with the accessories for the interface cable.
• Connect the harness of the optional counter to the black connector [C].
Optional Counter Interface Unit Type M12 (B870-21)
311
312
2. Installation
-
-
-
No.
-
-
-
-
Description
Screw: M3X8
Binding Self-Tapping Screw: M4X8
Clamp:LWS-1211Z
Clamp:NK-3N
Double Sided Tape
Key Counter Plate Nut
Key Counter Harness
Q’ty
1
3
2
1
2
2
1
Remarks
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
1.
Hold the key counter plate nuts [A] on the inside of the key counter bracket [B] and insert the key counter holder [C].
2.
Secure the key counter holder to the bracket ( x2).
3.
Install the key counter cover [D] ( x2).
Key Counter Bracket Type M3 (D739-09)
4.
Open the right door.
5.
Right rear cover [A] ( x4, among them, tapping screw x1)
• When installing, insert the projections [A] in the holes [B], taking care not to trap the harness inside.
313
314
2. Installation
6.
Remove the rear cover [A].
7.
Remove the controller box cover [A].
Red Circle: Remove / Blue Circle: Loosen
Key Counter Bracket Type M3 (D739-09)
8.
Route the key counter’s cable inside the machine and fasten it using the screw hole [A].
9.
Connect the key counter’s cable to the 4-pin connector [A] on the machine.
315
2. Installation
10.
Attach the supplied clamp [A], and then route the cable as shown.
11.
Open the slit in the rear cover to put the cable through, and then attach the rear cover while putting the cable through.
316
12.
Connect the key counter and cable.
13.
Attach the key counter [A] to the machine’s rear right.
Key Counter Bracket Type M3 (D739-09)
14.
Reinstall all the covers on the main machine.
15.
Peel off double sided tape on the key counter bracket and attach the key counter to the scanner right cover.
16.
Reassemble the machine.
317
318
2. Installation
Check the quantity and condition of the accessories against the following list.
No.
1 Screw: M3 x 8
2 Screw: M3 x 14
3 Screw: M4 x 25
Description
4 Tapping Screw: M3 x 10
5 Upper Tray
6 Lower Tray
7 Tray Bracket
8 Clamp
1
1
5
Q'ty
2
1
1
3
1
For This Model
Yes
Not used
Yes
Yes
Yes
Yes
Yes
Yes
Card Reader Bracket Type 3352 (D593-61)
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
1.
Open the ADF.
2.
Remove a screw for the scanner right cover.
3.
Remove the scanner right cover [A].
Remove the hook at the top, and then slide the cover towards the rear.
4.
Make 2 screw holes in the removed scanner right cover with a screwdriver or drill.
• Make the screw holes to be smaller than the screw size.
319
2. Installation
5.
Reattach the scanner right cover ( x2).
6.
Attach the tray bracket [A] to the scanner right cover ( x2: M3x10 tapping screw).
For this model, use the screw holes marked "3" on the table bracket.
320
7.
Attach the lower tray [A] to the tray bracket ( x2: M3 x 8).
Card Reader Bracket Type 3352 (D593-61)
8.
Attach the upper tray [B] to the tray bracket ( x1: M3 x 10).
9.
Attach the clamps ([1] to [5]) and route the harness around the machine as shown.
The USB cable is not supplied. Use a commercially available USB cable.
Scanner Right Cover
321
322
2. Installation
Rear Cover
10.
Connect the USB cable to the USB A slot.
NFC Card Reader Type M19 (D3BS-21)
No.
Description
1 Corner Cover
2 Reader Spacer
3 Reader Cover
4 Reader
5 Sponge Cushions
6 Ferrite Core (Black)
7 Interface Cable
Q'ty
1
1
1
1
2
1
1
Remarks
323
2. Installation
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
1.
Open the right door, and then remove the small cover [A].
2.
Remove the screw and the connector, and then remove the front upper cover [A].
324
• Remember that there is a tab at the positions of the red arrows.
• Rotate the operation panel [B] upward to a horizontal position, and then detach the front upper cover [A].
3.
Remove the original upper cover [A].
4.
Attach the corner cover [A] provided with this option.
Use the screws removed in the previous step.
NFC Card Reader Type M19 (D3BS-21)
325
326
2. Installation
5.
Remove the scanner front cover [A].
6.
Remove the operation panel upper cover [A].
7.
Remove the operation panel right cover [A].
NFC Card Reader Type M19 (D3BS-21)
8.
Thread the USB cable [B] through the notch in the corner cover [A] and attach the ferrite core [C].
• Attach the ferrite core 6 cm [A] away from the end of the cable.
• By doing so, it becomes easier to put the ferrite core inside the reader cover in step 12.
9.
Reattach the front upper cover to the machine.
327
328
2. Installation
10.
Attach the reader spacer [A].
11.
Attach the sponge cushions [A] to the reader spacer.
12.
Connect the card reader and interface cable.
Make sure to turn the USB cable as shown so that it threads through the notch in the spacer [A].
NFC Card Reader Type M19 (D3BS-21)
13.
Attach the reader cover [A].
14.
Connect the USB cable to the machine’s operation panel connector.
15.
Thread the USB cable through the U-shaped groove [A] at the hinge of the operation panel and notch [B] on the cover under the cover.
329
2. Installation
16.
Apply the clamp to fasten the USB cable to the machine.
Make sure that the cable is not loose between the connector and hinge [A] and the hinge and clamp [B].
17.
Tuck in the excess length portion of the USB cable in the space under the scanner.
330
18.
Reattach the removed covers.
Smart Card Reader Built-in Unit Type M19 (D3BS-22)
No.
1 Corner Cover
Description
2 IC Card Reader Spacer
3 IC Card Reader Table
4 Sponge
Q’ty
1
1
1
2
Remarks
• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
An IC card reader and a USB cable are not included with this unit. The customers must obtain these themselves, and the technicians must install them.
There are 2 ways to connect the USB cable of the IC card. One is to the machine USB slot which is the same way as the previous machine, and another is to the smart operation panel USB slot.
331
332
2. Installation
1.
Open the right door, and then remove the small cover [A].
2.
Remove the screw and the connector, and then remove the front upper cover [A].
• Remember that there is a tab at the positions of the red arrows.
• Rotate the operation panel [B] upward to a horizontal position, and then detach the front upper cover [A].
Smart Card Reader Built-in Unit Type M19 (D3BS-22)
3.
Remove the original upper cover [A].
4.
Attach the corner cover [A] provided with this option.
Use the screws removed in the previous step.
333
334
2. Installation
5.
Remove the scanner right cover [A].
6.
Reattach the front upper cover with corner cover [A] to the main machine.
7.
Pass the USB cable [A] through the hole.
• This cable is not included in this unit. The user may need to provide it.
8.
Attach the table [A].
• There are three ribs on the back side of the table.
Smart Card Reader Built-in Unit Type M19 (D3BS-22)
9.
Attach the sponges [A] with double-sided tape.
335
336
2. Installation
10.
Connect the cable [B] to the IC reader [A] and attach the reader to the table.
• The USB cable should be turned as the following photo shows.
11.
Attach the IC card reader cover [A].
12.
Attach the three clamps ( x3).
Smart Card Reader Built-in Unit Type M19 (D3BS-22)
13.
Remove the cover to make the hole [A] to pass the cable through.
14.
Connect the USB connector to the USB interface of the controller.
337
338
2. Installation
15.
Route the cable as shown in the following photo.
Tuck in the excess length portion of the cable in the space over the controller box.
16.
Reattach the exterior covers.
1.
Open the right door, and then remove the small cover [A].
Smart Card Reader Built-in Unit Type M19 (D3BS-22)
2.
Remove the screw and the connector, and then remove the front upper cover [A].
• Remember that there is a tab at the positions of the red arrows.
• Rotate the operation panel [B] upward to a horizontal position, and then detach the front upper cover [A].
3.
Remove the original upper cover [A].
339
340
2. Installation
4.
Attach the corner cover [A] provided with this option.
Use the screws removed in the previous step.
5.
Remove the scanner front cover [A].
6.
Remove the operation panel upper cover [A].
7.
Remove the operation panel right cover [A].
Smart Card Reader Built-in Unit Type M19 (D3BS-22)
8.
Thread the USB cable [B] through the notch in the front upper cover [A] and attach the ferrite core [C].
9.
Reattach the front upper cover to the main machine.
10.
Attach the reader spacer [A].
341
342
2. Installation
11.
Attach the sponge cushions [A] to the reader spacer.
12.
Connect the card reader and interface cable.
Make sure to turn the USB cable as shown so that it threads through the notch in the spacer [A].
13.
Attach the reader cover [A].
Smart Card Reader Built-in Unit Type M19 (D3BS-22)
14.
Connect the USB cable to the main machine’s operation panel connector.
15.
Thread the USB cable through the U-shaped groove [A] at the hinge of the operation panel and notch [B] in the cover under the cover.
16.
Apply the clamp to fasten the USB cable to the main machine.
Make sure that the cable is not loose between the connector and hinge [A] and the hinge and clamp [B].
343
344
2. Installation
17.
Tuck in the excess length portion of the USB cable in the space under the scanner.
18.
Reattach the removed covers.
SD Card Options
[A]: SD card slot 1 (option slot)
[B]: SD card slot 2 (service slot)
Optional SD cards can be set in either slot 1 or slot 2. But slot 2 is the service slot, so we recommend that you use slot 1 to install the SD card options.
SD card options for this machine
• OCR Unit Type M13 (page 358)
• XPS Direct Print Option Type M19 (page 356)
• PostScript3 Unit Type M19 (page 352)
• Camera Direct Print Card Type M19 (page 354)
• DataOverwriteSecurity Unit Type M19 (page 361)
• SD Card for Fonts Type D
• Unicode Font Package for SAP(R) 1 License
• Unicode Font Package for SAP(R) 10 Licenses
• Unicode Font Package for SAP(R) 100 Licenses
• Fax Connection Unit Type M19
• In this machine, it is possible to transfer data from a "Postscript3 Unit" SD card, unlike in earlier models, due to a change in the software licensing (the part of the Postscript software that requires
345
346
2. Installation licensing is now built into the controller, so the portion on the SD card can be moved to another SD card).
SD Card Appli Move
Since there are only two SD card slots (one of them is a service slot), three or more SD card applications cannot be used simultaneously.
However, if multiple SD card applications are merged, three or more SD card options can be used.
This function is referred to as the "SD card merge function".
The "SD card merge function" is a function which enables the use of three or more functions within the capacity of two SD cards by physically transferring the function of one SD card to other SD cards (all SD card options can be stored in two SD cards).
However, SD card applications are under license, therefore, since an SD card license after merge is transferred to the target SD card, it cannot be used even if it is moved to the target machine.
Also, a process to prevent illegal copying is performed.
• After merge, store the empty SD card in the location shown below.
1.
Open the right door, and then remove the small cover [A].
347
348
2. Installation
2.
Remove the screw and the connector, and then remove the front upper cover [A].
• Remember that there is a tab at the positions in the red arrows.
• Rotate the operation panel [B] upward to a horizontal position, and then detach the front upper cover [A].
3.
Insert the SD card in the storage location [A] inside the cover.
SD Card Appli Move
"Move Exec" (SP5-873-001) lets you move application programs from the original SD card to another
SD card.
• The SD card as a destination is not specified.
1.
Turn the OFF the main power.
2.
Remove the SD card slot cover [A] ( ×1).
3.
Set the destination SD card (SD card where data is to be stored) in Slot 1 [A], and set the original SD card (SD card from which data is to be transferred) in Slot 2 [B].
4.
Turn ON the main power, and press [ENTER] in SP5-873-001 (SD Card Appli Move:
Move Exec).
5.
When a confirmation screen is displayed, press [ENTER] (it takes about 2 - 3 minutes).
• If [CANCEL] is pressed, the display returns to the previous screen.
• Note that if the power supply is turned off, a panel operation is performed, or the cover is opened during merge, it will result in a malfunction.
349
350
2. Installation
6.
When merge is complete, and the following screen is displayed, press [CLOSE].
• If the process is terminated abnormally, perform the merge in SP mode again.
• If the capacity of the destination SD card is insufficient, the merge operation cannot be performed.
7.
Press [END] twice.
8.
Turn OFF the main power.
9.
Remove the empty SD card after transfer from Slot 2.
10.
Reattach the slot cover ( ×1).
11.
Turn ON the main power, output the system setting list, and check that the options are recognized correctly.
"Undo Exec" (SP5-873-002) lets you move back application programs from an SD card in Slot 1
(upper) to the original SD card in Slot 2 (lower). You can use this program when, for example, you have mistakenly copied some programs by using “Move Exec”.
1.
Turn OFF the main power.
2.
Remove the SD card slot cover [A] ( ×1).
SD Card Appli Move
3.
Insert the integrated SD card in Slot 1 [A: Upper].
4.
Insert the SD card which became empty after integration in Slot 2 (lower slot).
5.
Turn On the main power, and press [ENTER] in SP5-873-002 (SD Card Appli Move: Undo
Exec).
6.
When a confirmation screen is displayed, press [ENTER].
• If [CANCEL] is pressed, the display returns to the previous screen.
• Note that if the power supply is turned off, a panel operation is performed, or the cover is opened during cancellation, it will result in a malfunction.
7.
When cancellation is complete, press [CLOSE].
8.
Press [END] twice.
9.
Turn OFF the main power.
10.
Reattach the SD card slot cover ( ×1).
11.
Turn ON the main power, and check that the application has been deleted.
351
352
2. Installation
No.
1 SD Card
2 PS3 Decal
Description Q’ty
1
1
• When installing more than one SD card, perform the merge operation (page 347 "SD Card Appli
1.
Remove the SD card slot cover [A].
2.
Insert the PS3 SD card in SD card slot 1 [A: Upper Slot].
PostScript3 Unit Type M19 (D3BD-05, -06, -07)
3.
Reattach the SD card slot cover ( ×1).
4.
Stick the "Adobe PostScript3" decal [A] on the front face of the MFP.
5.
Turn ON the main power.
6.
Print out the "Configuration Page", and then check if this option is correctly recognized.
• User Tools > Machine Features > Printer Features > List/Test Page > Configuration Page
• The PDF firmware installed as standard contains a program required to print PS3 data as default.
However, this PS3 program is normally disabled.
• The PS3 firmware is a dongle (key) which enables PS3 data printing functions. When the PS3 firmware is installed, the PS3 program in the PDF firmware is enabled. Due to this specification, the self-diagnosis result report shows the ROM part number/software version of the PDF firmware contained in the PS3 program.
353
354
2. Installation
No.
1 SD Card
Description Q’ty
1
• When installing more than one SD card, perform the merge operation (page 347 "SD Card Appli
1.
Remove the SD card slot cover [A].
Camera Direct Print Card Type M19 (D3BD-13)
2.
Insert the Camera Direct Print Card in SD card slot 1 [A: Upper Slot].
3.
Reattach the SD card slot cover.( ×1)
4.
Turn ON the main power.
5.
Attach the "PictBridge" decal on the front face of the MFP.
6.
Print out the "Configuration Page", and then check if this option is correctly recognized.
• User Tools > Machine Features > Printer Features > List/Test Page > Configuration Page
355
356
2. Installation
No.
1
Description
XPS Direct Print SD Card
Qty
1
Remarks
• When installing more than one SD card, perform the merge operation (page 347 "SD Card Appli
1.
Remove the SD card slot cover [A].
XPS Direct Print Option Type M19 (D3BC-24, -25, -26)
2.
Insert the XPS SD card in SD card slot 1 [A: Upper Slot].
3.
Reattach the SD card slot cover ( ×1).
4.
Turn ON the main power.
5.
Print out the "Configuration Page", and then check if this option is correctly recognized.
• User Tools > Machine Features > Printer Features > List/Test Page > Configuration Page
357
2. Installation
No.
1 SD Card
Description Q’ty
1
358
This option adds a searchable PDF function to the scanning function.
• The searchable PDF function performs OCR by the MFP on a document read with the scanner, and embeds text data in the PDF. This permits PDF text browsing, automatic assignment of filenames, and automatic alignment of document orientation.
• This option is provided with an SD card. By installing an SD card in the MFP, a functional icon is added to the control unit. It is not necessary to install software in a PC.
• If this option is installed, various settings related to the searchable PDF function are available.
• After reading of the document is completed (after it is read by the SPDF/ARDF and output), OCR is performed. Therefore, after reading is completed, documents can be collected from the document glass or SPDF/ARDF.
• Other functions, such as the copy function and printer function, can be used during OCR.
• When installing more than one SD card, perform the merge operation (page 347 "SD Card Appli
1.
Remove the SD card slot cover [A].
OCR Unit Type M13 (D3AC-23, -24, -25)
2.
Insert the OCR Unit SD card in SD card slot 1 [A: Upper Slot].
3.
Turn ON the main power.
4.
Enter the SP mode, and then press "Enter" in SP5-878-004 (Option Setup: OCR
Dictionary).
The SD card ID is saved in the NVRAM, and the ID of the MFP is saved on the SD card. The MFP and SD card are thereby linked.
5.
When "operation complete" is displayed, press "Close".
• If installation fails, "Failed" is displayed.
• If installation fails, perform the following steps.
1. Check whether it is a used SD card.
2. Switch the power OFF, and repeat steps 1-5.
6.
Turn the machine OFF and back ON again.
7.
Press "Enter" in SP5-878-004 (Option Setup: OCR Dictionary).
Dictionary data is copied to the HDD.
• On the first run, SP5-878-004 links the SD card, and on the second run, copies dictionary data.
359
360
2. Installation
8.
Turn OFF the main power.
9.
Remove the SD card from the SD card slot.
• Keep the SD card in the SD card storage location of the MFP. The original SD card is needed in the event of a HDD malfunction.
10.
Reattach the SD card slot cover.
11.
Turn ON the main power.
12.
Press [File Format / File Name] on the scanner function screen.
13.
Check that [OCR setting] is displayed on the "File format / "File Name" screen.
• After installation, the OCR setting can be changed on the "OCR setting" screen.
• When setting OCR, set [OCR setting] to [Yes]. (Default setting: [No])
When this option is installed, a function is saved on the HDD, and ID information on the SD card is saved in the NVRAM. Therefore, when replacing the HDD and NVRAM, this option must be reinstalled.
When storing the original SD card
• When only the HDD is replaced
Reinstall using the original SD card.
• When only the NVRAM is replaced
When performing upload/download of NVRAM data, reinstall using the original SD card.
When not performing upload/download of NVRAM data, order and reinstall a new SD card
(service part).
• When the HDD and NVRAM are replaced simultaneously
Reinstall using the original SD card.
If the original SD card is lost
Order and reinstall a new SD card (service part).
DataOverwriteSecurity Unit Type M19 (D3BS-03)
The machine’s hard disk stores all document data from the Copier, Printer, and Scanner functions. It also stores the data of users’ Document Server and code counters, and the Address Book. To prevent data on the hard disk being leaked before disposing of the machine, you can overwrite all data stored on the hard disk (Erase All Memory). You can also automatically overwrite temporarily-stored data (Auto Erase
Memory).
The function of this option is completely the same as the Data Overwrite Security in Security Functions,
which is standard on this machine (page 374 "Security Settings")
This option should be installed only for the customer who requires the CC certified Data Overwrite
Security function.
Check the quantity and condition of the accessories in the box against the following list.
No.
1 SD Card
Comments Sheet
Operating Instructions CD-ROM
Description Q’ty
1
1
1
361
362
2. Installation
1.
Confirm that the Data Overwrite Security unit SD card is the correct type for the machine.
The correct type for this machine is "Type M19".
• If you install any version other than "Type M19" for this machine, you will have to replace the
NVRAM and do this installation procedure again.
2.
Make sure that the following settings are not at their factory default values:
• Supervisor login password
• Administrator login name
• Administrator login password
If any of these settings is at a factory default value, tell the customer these settings must be changed before you do the installation procedure.
3.
Make sure that "Admin. Authentication" is ON.
User Tools > Machine Features > System Settings > Administrator Tools > Administrator
Authentication Management > Admin. Authentication
If this setting is OFF, tell the customer this setting must be ON before you do the installation procedure.
4.
Make sure that "Administrator Tools" is enabled (selected).
User Tools > Machine Features > System Settings > Administrator Tools >
Administrator Authentication Management> Available Settings
If this setting is disabled (not selected), tell the customer this setting must be enabled (selected) before you do the installation procedure.
• See the Operating Instructions (Security Guide) for the factory default values.
Before opening the corrugated envelope, make sure that the seal has not been broken or peeled off. If the seal has been broken or peeled off (even partially), this is considered an arrival defect. Note that once the seal is peeled off, this will leave a mark on the bag.
DataOverwriteSecurity Unit Type M19 (D3BS-03)
• You must check the box seals to make sure that they were not removed after the items were sealed in the box at the factory before you do the installation.
1.
Check the box seals [A] on each corner of the box.
• Make sure that a tape is attached to each corner.
• The surfaces of the tapes must be blank. If you see "VOID" on the tapes, do not install the components in the box.
2.
If the surfaces of the tapes do not show "VOID", remove them from the corners of the box.
3.
You can see the "VOID" marks [B] when you remove each seal. In this condition, they cannot be attached to the box again.
1.
Turn the main power off, and then remove the power plug and cables that are connected.
363
2. Installation
2.
Remove the SD card slot cover [A].
3.
Insert the DataOverwriteSecurity Unit Type M19 SD card in SD card slot 1 [A: Upper Slot].
364
4.
Reattach the SD card slot cover ( ×1).
5.
Insert the power cord into the outlet and turn ON the main power.
• When installing more than one SD card, perform the merge operation.
6.
Enter the SP mode.
7.
Do this step only if you are installing the option on a machine that is already in use (not a new machine):
• If the customer wishes to continue using the same hard disk, execute all three SP modes below.
• SP5-801-014 (Clear DCS Setting)
• SP5-832-001 (HDD Formatting (ALL))
• SP5-832-002 (HDD Formatting (IMH))
• If customer wishes to replace the hard disk with a new one, execute SP5-801-014 only.
• If the customer continues using the same hard disk, the overwriting of the data stored on the disk before the option is installed cannot be guaranteed. It is highly recommended to replace the hard disk with a new one.
DataOverwriteSecurity Unit Type M19 (D3BS-03)
8.
Set SP5-836-001 (Capture Function (0:Off 1:On)) to a value of 0 (disable).
9.
Execute SP5-878-001 ([Option Setup: Data Overwrite Security)
If the installation fails, "Installation failed" is displayed when this SP is executed.
10.
Print out the System Settings List and make sure that the option was installed successfully.
11.
Reconnect the network cable.
12.
Execute SP5-990-005 (SP print mode Diagnostic Report).
Make sure to shut down and reboot the machine once before printing the SMC. Otherwise, the latest settings may not be collected when the SMC is printed.
13.
Make sure that ROM number "D3BC5757A" and firmware version "1.02" appear in both of the following areas on the report (they must match):
• "ROM Number / Firmware Version" - "HDD Format Option"
• "Loading Program"
1.
Press the [User Tools] icon.
2.
Press [Machine Features].
3.
Press [System Settings].
4.
Press [Administrator Tools].
5.
Press [Next] three times.
6.
Press [Auto Erase Memory Setting].
7.
Press [On].
365
2. Installation
8.
Select the method of overwriting.
• If you select [NSA] or [DoD], proceed to Step 11.
• If you select [Random Numbers], proceed to Step 9.
9.
Press [Change].
10.
Enter the number of times that you want to overwrite using the ten keys, and then press
[#].
366
The Random Numbers method overwrites the data using random numbers. You can set the overwrite to be performed anywhere from 1-9 times, with a default of 3 times.
11.
Press [OK].
12.
Make sure that the Data Overwrite icon is displayed in the bottom right hand corner of the screen.
13.
Take a test copy, and then make sure that the Data Overwrite icon changes from "Dirty"
(solid) to "Dirty" (blinking), and then to "Clear".
• If the Data Overwrite icon does not change to Clear, check to see if there are any active
Sample Print or Locked Print jobs. A Sample Print or Locked Print job can only be overwritten after it has been executed.
• The Dirty icon blinks while an overwrite is in progress.
DataOverwriteSecurity Unit Type M19 (D3BS-03)
• If you use your machine for a while with Auto Erase Memory disabled, and then suddenly enable it, the overwrite process may take 10 or more hours depending on HDD usage.
Data Overwrite icon:
Icon [1]
This icon is lit when there is temporary data to be overwritten, and blinks during overwriting.
Icon [2]
This icon is lit when there is no temporary data to be overwritten.
SP descriptions
• SP5-801-014 (Memory Clear: Clear DCS Setting)
Initializes the DCS (Delivery Control Service) settings.
• SP5-832-001 (HDD Formatting : HDD Formatting (ALL))
Initializes the hard disk.
• SP5-832-002 (HDD Formatting : HDD Formatting (IMH))
Initializes the hard disk.
• SP5-836-001 (Capture Settings: Capture Function (0:Off 1:On))
With this function disabled, the settings related to the capture feature cannot be initialized, displayed, or selected.
• 5-878-001 (Data Overwrite Security)
Enables the Data Overwrite Security unit. Press "EXECUTE" on the operation panel. Then turn the machine off and on.
• SP5-990-005 (SP Print Mode: Diagnostic Report).
Prints the configuration sheets of the system and user settings : SMC.
Make sure to shut down and reboot the machine once before printing the SMC. Otherwise, the latest settings may not be collected when the SMC is printed.
367
368
2. Installation
• Prepare and check the following check points before you visit the customer site. For details, ask the
@Remote key person.
Check points before making @Remote settings
1.
The setting of SP5-816-201 in the mainframe must be "0".
2.
Print the SMC with SP5-990-002 and then check if a device ID2 (SP5-811-003) must be correctly programmed.
• 6 spaces must be put between the 3-digit prefix and the following 8-digit number (e.g.
xxx______xxxxxxxx).
• ID2 (SP5-811-003) and the serial number (SP5-811-001) must be the same (e.g. ID2:
A01______23456789 = serial No. A0123456789)
• Make sure to shut down and reboot the machine once before printing the SMC. Otherwise, the latest settings may not be collected when the SMC is printed.
3.
The following settings must be correctly programmed.
• Proxy server IP address (SP5-816-063)
• Proxy server Port number (SP5-816-064)
• Proxy User ID (SP5-816-065)
• Proxy Password (SP5-816-066)
4.
Get a Request Number
Execute the @Remote Settings
1.
Enter the SP mode.
2.
Input the Request number which you have obtained from @Remote Center GUI, and then enter [OK] with SP5-816-202.
3.
Confirm the Request number, and then click [EXECUTE] with SP5-816-203.
4.
Check the confirmation result with SP5-816-204.
Value
0
3
4
5
Succeeded
Meaning
-
Solution/ Workaround
Communication error (proxy enabled) Check the network condition.
Communication error (proxy disabled) Check the network condition.
Proxy error (authentication error) Check Proxy user name and password.
@Remote Settings
Value
6
8
9
11
12
20
21
Meaning Solution/ Workaround
Communication error
Other error
Check the network condition.
See "SP5816-208 Error Codes" below this.
Request number confirmation executing Processing… Please wait.
Already registered
Parameter error
Dial-up authentication error
Answer tone detection error
-
-
22
23
Carrier detection error
Invalid setting value (modem)
* These errors occur only in the modems that support @Remote.
24
25
Low power supply current unplugged modem
26 Busy line
5.
Make sure that the screen displays the Location Information with SP5-816-205 only when it has been input at the Center GUI.
6.
Click [EXECUTE] to execute the registration with SP5-816-206.
7.
Check the registration result with SP5-816-207.
4
5
2
3
Value
0
1
8
Meaning
Succeeded
Request number error
Solution/ Workaround
-
Check the request number again.
Already registered
Communication error (proxy enabled)
Check the registration status.
Check the network condition.
Communication error (proxy disabled) Check the network condition.
Proxy error (Authentication error)
Other error
Check Proxy user name and password.
See "SP5-816-208 Error Codes" below this.
369
370
2. Installation
Value
9
11
12
20
21
22
Parameter error
Meaning
Dial-up authentication error
Solution/ Workaround
Request number confirmation executing Processing… Please wait.
Already registered -
-
Answer tone detection error
Carrier detection error
* These errors occur only in the modems that support @Remote.
23
24
Invalid setting value (modem)
Low power supply current
25
26 unplugged modem
Busy line
8.
Exit the SP mode.
SP5-816-208 Error Codes
Caused by Operation Error, Incorrect Setting
Code
-12002
-12003
-12004
-12005
-12006
-12007
Meaning
Inquiry, registration attempted without acquiring Request No.
Attempted registration without execution of a confirmation and no previous registration.
Attempted setting with illegal entries for certification and ID2.
@Remote communication is prohibited. The device has an Embedded RC gate-related problem.
A confirmation request was made after the confirmation had been already completed.
The request number used at registration was different from the one used at confirmation.
Solution/ Workaround
Obtain a Request Number before attempting the Inquiry or Registration.
Perform Confirmation before attempting the Registration.
Check ID2 of the mainframe.
Make sure that "Remote Service" in User
Tools is set to "Do not prohibit".
Execute registration.
Check Request No.
@Remote Settings
Code
-12008
Meaning
Update certification failed because mainframe was in use.
-12009
The ID2 in the NVRAM does not match the
ID2 in the individual certification.
-12010 The certification area is not initialized.
Solution/ Workaround
Check the mainframe condition. If the mainframe is in use, try again later.
Check ID2 of the mainframe.
Initialize the certification area.
-2391
-2392
-2393
-2394
-2395
-2396
-2397
-2398
Error Caused by Response from GW URL
Code
-2385
-2387
-2389
-2390
Other error
Meaning
Not supported at the Service Center
Database out of service
Program out of service
Two registrations for the same mainframe
Parameter error
External RCG not managed
Mainframe not managed
Box ID for external RCG is illegal.
Mainframe ID for external RCG is illegal.
Incorrect ID2 format
Incorrect request number format
Solution/ Workaround
Check the registration condition of the mainframe
Check the ID2 of the mainframe.
Check the Request No.
SP descriptions
• SP5-816-201 (Remote Service: Regist Status DFU(SSP))
Displays a number that indicates the status of the @Remote service device.
0: Neither the registered device by the external nor embedded RCG device is set.
1: The embedded RCG device is being set. Only Box registration is completed. In this status, this unit cannot answer a polling request from the external RCG.
371
372
2. Installation
2: The embedded RCG device is set. In this status, the external RCG unit cannot answer a polling request.
3: The registered device by the external RCG is being set. In this status the embedded RCG device cannot be set.
4: The registered module by the external RCG has not started.
• SP5-990-002 (SP Print Mode: SP(Mode Data List))
Prints the configuration sheets of the system and user settings : SMC.
Make sure to shut down and reboot the machine once before printing the SMC. Otherwise, the latest settings may not be collected when the SMC is printed.
• SP5-811-003 (Machine No. Setting: ID2 Code Display)
Sets the ID-2 code used to identify the @remote device at installation.
• SP5-816-063 (Remote Service: Proxy server IP address)
This SP sets the address of the proxy server used for communication between the RCG device and the gateway. Use this SP to set up or display the customer proxy server address.
The address is necessary to set up the embedded RCG-N.
The address display is limited to 127 characters. Characters beyond the 127 characters are ignored.
This address is customer information and is not printed in the SMC report.
• SP5-816-064 (Remote Service: Proxy server Port number)
This SP sets the port number of the proxy server used for communication between the embedded
RCG-N and the gateway. This setting is necessary to set up the embedded RC Gate-N.
This port number is customer information and is not printed in the SMC report.
• SP5-816-065 (Remote Service: Proxy User ID)
This SP sets the HTTP proxy certification user name.
The length of the name is limited to 31 characters. Any character beyond the 31st character is ignored.
This name is customer information and is not printed in the SMC report.
• SP5-816-066 (Remote Service: Proxy Password)
This SP sets the HTTP proxy certification password.
The length of the password is limited to 31 characters. Any character beyond the 31st character is ignored.
This name is customer information and is not printed in the SMC report.
• SP5-816-202 (Remote Service: Letter Number DFU(SSP))
Allows entry of the number of the request needed for the RCG-N device.
• SP5-816-203 (Remote Service: Confirm Execute)
@Remote Settings
Executes the inquiry request to the @Remote GW URL.
• SP5-816-204 (Remote Service: Confirm Result DFU(SSP))
Displays a number that indicates the result of the inquiry executed with SP5816 203.
• SP5-816-205 (Remote Service: Confirm Place DFU(SSP))
Displays the installed section informed from G/W for response of request number inquiry if the section is enrolled on the G/W.
• SP5-816-206 (Remote Service: Register Execute)
Executes "Embedded RCG Registration".
• SP5-816-207 (Remote Service: Register Result DFU(SSP)
Displays a number that indicates the registration result.
373
374
2. Installation
The machine contains the Security functions (Data Overwrite Security and HDD Encryption unit) in the controller board.
If you are installing a new machine, it is recommended to activate the Data Overwrite Security and HDD
Encryption by selecting "Format All Data" from "System Settings" on the operation panel.
• This method is recommended because there is no user data on the hard drive yet (Address Book data, image data, etc.).
If the customer wishes to activate the Data Overwrite Security and HDD Encryption unit on a machine that is already running, it is recommended to activate the unit by selecting "All Data" from "System
Settings" on the operation panel.
• Selecting "All Data" will preserve the data that has already been saved to the HDD. (If "Format All
Data" is selected, all user data saved to the HDD up to that point will be erased).
Immediately after encryption is enabled, the encryption setting process will take several minutes to complete before you can begin using the machine.
• If encryption is enabled after data has been stored on the HDD, or of the encryption key is changed, this process can take up to three and a half hours or more.
The machine cannot be operated while data is being encrypted.
Once the encryption process begins, it cannot be stopped.
Make sure that the machine's main power is not turned off while the encryption process is in progress.
If the machine's main power is turned off while the encryption process is in progress, the HDD will be damaged and all data on it will be unusable.
Print the encryption key and keep the encryption key (which is printed as a paper sheet).
Keep the encryption key in a safe place. If the encryption key is lost and is needed, the controller board,
HDD and NVRAM must all be replaced at the same time.
• "NVRAM" mentioned in here means the NVRAM on the Controller Board.
• "NVRAM" or EEPROM on the BCU has nothing to do with this.
Please use the following procedure when the Data Overwrite Security and HDD Encryption are reinstalled.
Security Settings
1.
Make sure that the following settings (1) to (3) are not at their factory default values.
(1) Supervisor login password
(2) Administrator login name
(3) Administrator login password
If any of these settings is at a factory default value, tell the customer these settings must be changed before you do the installation procedure.
2.
Make sure that "Admin. Authentication" is on.
[User Tools] icon -> [Machine Features] -> [System Settings] -> [Administrator Tools] ->
[Administrator Authentication Management] -> [Admin. Authentication]
If this setting is off, tell the customer this setting must be on before you do the installation procedure.
3.
Make sure that "Administrator Tools" is enabled (selected).
[User Tools] icon -> [Machine Features] -> [System Settings] -> [Administrator Tools] ->
[Administrator Authentication Management] -> [Available Settings]
If this setting is disabled (not selected), tell the customer this setting must be enabled (selected) before you do the installation procedure.
1.
Connect the network cable if it needs to be connected.
2.
Turn ON the main power.
3.
Go into the SP mode and push "EXECUTE" in SP5-878-001.
4.
Exit the SP mode and turn off the operation switch. Then turn off the main power switch.
5.
Turn on the machine power.
6.
Do SP5-990-005 (SP print mode Diagnostic Report).
Make sure to shut down and reboot the machine once before printing the SMC. Otherwise, the latest settings may not be collected when the SMC is printed.
7.
Go into the User Tools mode, and select [Machine Features] [System Settings]
[Administrator Tools] [Auto Erase Memory Setting] [On].
375
2. Installation
8.
Exit the User Tools mode.
376
Icon [1]
This icon is lit when there is temporary data to be overwritten, and blinks during overwriting.
Icon [2]
This icon is lit when there is no temporary data to be overwritten.
9.
Check the display and make sure that the overwrite erase icon appears.
10.
Check the overwrite erase icon.
The icon [1] is lit when there is temporary data to be overwritten, and blinks during overwriting.
The icon [2] is lit when there is no temporary data to be overwritten.
The Auto Erase Memory function can be enabled by the following procedure.
1.
Log in as the machine administrator from the control panel.
2.
Press the [User Tools] icon.
3.
Press [Machine Features].
4.
Press [System Settings].
5.
Press [Administrator Tools].
Security Settings
6.
Press [Next] three times.
7.
Press [Auto Erase Memory Setting].
8.
Press [On].
9.
Select the method of overwriting.
If you select [NSA] or [DoD], proceed to step 12.
If you select [Random Numbers], proceed to step 10.
10.
Press [Change].
11.
Enter the number of times that you want to overwrite using the number keys, and then press [#].
12.
Press [OK]. Auto Erase Memory is set.
13.
Log out.
14.
Check the display and make sure that the overwrite erase icon appears.
15.
Check the overwrite erase icon.
The icon [1] is lit when there is temporary data to be overwritten, and blinks during overwriting.
The icon [2] is lit when there is no temporary data to be overwritten.
377
2. Installation
Icon [1] This icon is lit when there is temporary data to be overwritten, and blinks during overwriting.
Icon [2] This icon is lit when there is no temporary data to be overwritten.
378
1.
Make sure that the following settings (1) to (3) are not at the factory default settings.
(1) Supervisor login password
(2) Administrator login name
(3) Administrator login password
If any of these settings is at a factory default value, tell the customer these settings must be changed before you do the installation procedure.
2.
Confirm that "Admin. Authentication" is on:
[User Tools] icon - [Machine Features] - [System Settings] - [Administrator Tools] - [Administrator
Authentication Management] - [Admin. Authentication] - [On]
If this setting is off, tell the customer that this setting must be on before you can do the installation procedure.
Security Settings
3.
Confirm that "Administrator Tools" is selected and enabled.
[User Tools] icon - [Machine Features] - [System Settings] - [Administrator Tools] - [Administrator
Authentication Management] - [Available Settings]
"Available Settings" is not displayed until step 2 is done.
If this setting is not selected, tell the customer that this setting must be selected before you can do the installation procedure.
1.
Turn ON the main power, and then enter the SP mode.
2.
Select SP5-878-002, and then press "Execute" on the LCD.
3.
Exit the SP mode after "Completed" is displayed on the LCD.
4.
Turn OFF the main power.
Machine Data Encryption Settings can be enabled by the following procedure.
• When setting up encryption, specify whether to start encryption after deleting data (initialize) or encrypt and retain existing data. If data is retained, it may take some time to encrypt it.
1.
Turn ON the main power.
2.
Log in as the machine administrator from the control panel.
3.
Press the [User Tools] icon.
4.
Press [Machine Features].
5.
Press [System Settings].
6.
Press [Administrator Tools].
7.
Press [Next] three times.
379
2. Installation
8.
Press [Machine Data Encryption Settings].
9.
Press [Encrypt].
380
10.
Select the data to be carried over to the HDD and not be reset.
To carry all of the data over to the HDD, select [All Data].
To carry over only the machine settings data, select [File System Data Only].
To reset all of the data, select [Format All Data].
Security Settings
11.
Select the backup method.
If you have selected [Save to SD Card], load an SD card into the media slot on the side of the control panel and press [OK] to back up the machine's data encryption key.
If you have selected [Print on Paper], press the [Start] key. Print out the machine's data encryption key.
12.
Press [OK].
381
382
2. Installation
13.
Press [Exit].
14.
Press [Exit].
15.
Log out.
16.
Turn OFF the main power, and then turn the main power back ON.
The machine will start to convert the data on the memory after you turn on the machine. Wait until the message "Memory conversion complete. Turn the main power switch off." appears, and then turn the main power off again.
1.
Press the [User Tools] icon.
2.
Press [Machine Features].
3.
Press [System Settings].
4.
Press [Administrator Tools].
5.
Press [Machine Data Encryption Settings].
6.
Confirm whether the encryption has been completed or not on this display.
Security Settings
Print the encryption key
Use the following procedure to print the key again if it has been lost or misplaced.
1. Press the [User Tools] icon.
2. Press [Machine Features].
3. Press [System Settings].
4. Press [Administrator Tools].
5. Press [Machine Data Encryption Settings].
If this item is not visible, press [Next] to display more settings.
6. Press [Print Encryption Key].
383
2. Installation
Encryption key sample
384
The encryption key is printed out as a sheet of paper like the example shown above.
Please instruct the customer to keep it in a safe place.
The encryption key can be backed up. Select whether to save it to an SD card or to print it.
• The encryption key is required for data recovery if the machine malfunctions. Be sure to store the encryption key safely for retrieving backup data.
1.
Log in as the machine administrator from the control panel.
2.
Press the [User Tools] icon.
3.
Press [Machine Features].
4.
Press [System Settings].
5.
Press [Administrator Tools].
6.
Press [Next] three times.
7.
Press [Machine Data Encryption Settings].
Security Settings
8.
Press [Print Encryption Key].
9.
Select the backup method.
If you have selected [Save to SD Card], load an SD card into the media slot on the side of the control panel and press [OK]; once the machine's data encryption key is backed up, press [Exit].
If you have selected [Print on Paper], press the [Start] key. Print out the machine's data encryption key.
10.
Press [Exit].
11.
Log out.
How to restore the old encryption key to the machine
The following message appears after the controller board is replaced. In such a case, it is necessary to restore the encryption key to the new controller board.
To do this, follow the procedure below.
1.
Prepare an SD card that has been initialized in FAT16 format.
2.
Using a PC, create a folder in the SD card and name it "restore_key".
3.
Create a folder in the "restore_key" folder and name it the same as machine’s serial number, "xxxxxxxxxxx" (11 digits).
385
386
2. Installation
4.
Create a text file called "key_xxxxxxxxxxx.txt" and save it in the "xxxxxxxxxxx" folder.
Write the encryption key in the text file.
/restore_key/xxxxxxxxxxx/key_xxxxxxxxxxx.txt
• Ask an Administrator to enter the encryption key. The key has already been printed out by the user and may have been saved in the "key_xxxxxxxxxxx.txt" file. (The function of back-up the encryption key to the SD card directly is provided 11A products or later.)
5.
Turn ON the machine’s main power.
6.
Confirm that a message is displayed on the LCD telling to insert the SD card that contains the encryption key.
7.
Turn OFF the main power.
8.
Insert the SD card that contains the encryption key into SD card slot 2 (the lower slot).
9.
Turn ON the main power.
• The machine will automatically restore the encryption key to the flash memory on the controller board.
10.
Turn OFF the main power when the machine has returned to normal status.
11.
Remove the SD card from SD card slot 2.
How to do a forced start up with no encryption key
If the encryption key back-up has been lost, follow the procedure below to do a forced start-up.
• The HDD will be formatted after the forced start-up.
• Encrypted data will be deleted.
• User settings will be cleared.
1.
Prepare an SD card.
2.
Create a directory named "restore_key" inside the root directory of the SD card. Then, save the "nvram_key.txt" file using the following name:
/restore_key/nvram_key.txt
3.
Create a text file and write "nvclear".
• Write this string at the head of the file.
• Use all lower-case letters.
• Do not use quotation marks or blank spaces.
Security Settings
• It is judged that a forced start has been selected when the content of "nvclear" is executed and the machine shifts to the alternate system (forced start).
4.
Confirm that a message is displayed on the LCD telling to insert the SD card that contains the encryption key.
5.
Turn off the main power.
6.
Insert the SD card that contains the encryption key into SD card slot 2 (the lower slot).
7.
Turn ON the main power.
The machine automatically clear the HDD encryption.
8.
Turn OFF the main power when the machine has returned to normal status.
9.
Remove the SD card from SD card Slot 2.
10.
Turn ON the main power.
11.
Memory clear SP5-801-xxx (Exclude SP-5-801-001: All Clear and SP-5-801-002:
Engine), and clear SP5-846-046: address book.
12.
Set necessary user settings in User Tools.
SP descriptions
• SP5-878-002 (Option Setup: HDD Encryption)
Executes the setup for encryption.
• SP5-990-005 (SP Print Mode: Diagnostic Report)
Prints the configuration sheets of the system and user settings : SMC.
Make sure to shut down and reboot the machine once before printing the SMC. Otherwise, the latest settings may not be collected when the SMC is printed.
• SP5-801-001 (Memory Clear: All Clear)
Resets all correction data for process control and all software counters, and returns all modes and adjustments to their default values.
• SP5-801-002 (Memory Clear: Engine)
Clears non-volatile memory of engine.
• SP5-846-046 (UCS Setting: Addr Book Media)
Displays the slot number where an address book data is in.
0: Unconfirmed
1: SD Slot 1
2: SD Slot 2
3: SD Slot 3
4: USB Flash ROM
10: SD Slot 10
387
388
2. Installation
20: HDD
30: Nothing
There are two ways to reset the PM counter for this machine.
"Method 2 By [PM Counter / New Unit Set] Menu" is recommended for its ease of operation.
• After the PM counter for the fusing sleeve belt unit reaches its PM life (400K pages or
313,153,000 mm), the machine stops the operation automatically. Replace the fusing sleeve belt unit before the machine stops its operation (stop warning: 415K pages or 302,229,000 mm, stop:
430K pages or 313,153,000 mm).
• For the following units, there is a new unit detection mechanism. It is not necessary to set SPs (New
Unit Detection).
- Fusing unit as a complete unit
- PCDU as a complete unit
- Waste Toner Bottle (When the machine stopped because the waste toner bottle was full)
1.
Enter the SP mode.
2.
Output the SMC logging data with SP5-990-004.
Make sure to shut down and reboot the machine once before printing the SMC. Otherwise, the latest settings may not be collected when the SMC is printed.
3.
Set the following SPs (New Unit Detection) to "1".
Item
Development unit
• Replacement procedure: page 462
SP
Black: SP3-701-003
Yellow: SP3-701-072
Cyan: SP3-701-026
Magenta: SP3-701-049
389
390
3. Preventive Maintenance
PCU
Item
• Replacement procedure: page 462
SP
Black: SP3-701-002
Yellow: SP3-701-071
Cyan: SP3-701-025
Magenta: SP3-701-048
Pressure roller
• Replacement procedure: page 550
Fusing sleeve belt unit
• Replacement procedure: page 546
(Complete fusing unit is not necessary to set SP3-701.)
Image Transfer Belt Unit
• Replacement procedure: page 474
Image Transfer Cleaning Unit
• Replacement procedure: page 478
Pressure roller: SP3-701-118
Fusing sleeve belt unit: SP3-701-116
SP3-701-093
SP3-701-102
Paper Transfer Roller Unit
• Replacement procedure: page 495
SP3-701-109
Waste Toner Bottle
(When the bottle is replaced before the machine detects bottle full and stops)
• Replacement procedure: page 472
Ozone Filter, Dust Filter
• Replacement procedure: page 625
SP3-701-142
SP3-701-131
4.
Turn the main power switch OFF, and disconnect the power cord from the outlet.
5.
Replace the PM parts and turn the main power ON.
The machine will reset the PM counters automatically. In the case of the development unit, developer initialization will also be done automatically.
6.
Exit the SP mode.
1.
Enter the SP mode.
PM Parts Settings
2.
Output the SMC logging data with SP5-990-004.
Make sure to shut down and reboot the machine once before printing the SMC. Otherwise, the latest settings may not be collected when the SMC is printed.
3.
Press [PM Counter / New Unit Set].
4.
Press [All PM Parts List : New Unit Set].
5.
Set the PM part that you want to replace to "YES" under "New Unit Set".
After pressing "YES", the [Exit] key will not be available.
391
3. Preventive Maintenance
392
6.
Turn OFF the main power and unplug the power cord from the wall outlet.
7.
Replace the PM parts and turn the main power ON.
The machine will reset the PM counters automatically. In the case of the development unit, developer initialization will also be done automatically.
8.
Exit the SP mode.
1.
Output the SMC logging data with SP5-990-004 and check the counter values.
Make sure to shut down and reboot the machine once before printing the SMC. Otherwise, the latest settings may not be collected when the SMC is printed.
2.
Make sure that the PM counters for the replaced units are "0" with SP7-621, or SP7-944.
If the PM counter for a unit was not reset, then execute the new unit detect setting with
SP3-701 again and turn the machine OFF/ON.
3.
Make sure that the exchange counter counts up with SP7-853.
4.
Make sure that the counters for the previous units (SP7-908) on the new SMC logging data list (from step 2 above) are equal to the counters (SP7-621, or SP7-944) for these units on the previous SMC logging data list (the list that was output in the "Before removing the old parts" section).
5.
Make sure that the unit replacement date is updated with SP7-950.
• SP7-621-001 (PM Counter Display: Paper)
Displays the number of sheets printed for each current maintenance unit.
When a unit is replaced, the machine automatically detects that the new unit is installed.
PM Parts Settings
Then, the current PM counter value is automatically moved to the PM Counter – Previous
(SP7-906-1 to 10) and is reset to "0".
• SP7-853 (Replace Counter)
Displays the number of times each PM part has been replaced.
• SP7-908 (Previous Unit Counter: Pages (%))
Displays the PM counter of the previous PM Part which was replaced last time.
• SP7-950 (Unit Replacement Date)
Displays the replacement date of each PM unit.
• SP5-990 (SP Print Mode)
Prints the configuration sheets of the system and user settings : SMC.
Make sure to shut down and reboot the machine once before printing the SMC. Otherwise, the latest settings may not be collected when the SMC is printed.
1.
Clean the exposure glasses (for DF and book scanning).
2.
Enter the user tools mode.
3.
Do the "Automatic Color Calibration (ACC)" for the copier mode & printer mode as follows:
• Print the ACC test pattern (User Tools > Maintenance > ACC > Start).
• Put the printout on the exposure glass.
• Put 10 sheets of white paper on the test chart. This ensures the precise ACC adjustment.
• Close the ARDF or the platen cover.
• Press "Start Scanning" on the LCD. Then, the machine starts the ACC.
4.
Exit the User Tools mode, and then enter the SP mode.
5.
Perform line adjustment.
SP2-111-004: Forced Line Position Adj. Mode d
The result can be checked with SP2-194-007 (MUSIC Execution Result Execution Result)
(0: Success, 1: Failure).
Also, results for each color can be checked with SP2-194-010 to 013.
6.
Exit the SP mode.
• SP2-194-007 (MUSIC Execution Result: Execution Result)
393
394
3. Preventive Maintenance
Displays the result code of MUSIC adjustment.
0: Success
1: Failure
• SP2-194-010 to 013 (MUSIC Execution Result: Error Result C,M, Y, K)
Displays the result code of MUSIC adjustment for each color.
0: Not done
1: Completed successfully
2: Cannot detect patterns
3: Fewer lines on the pattern than the target
4: Out of the adjustment range
5 to 9: Not used
Check if the sample image has been copied normally.
See "Appendices" for the following information:
• Preventive Maintenance Items
PM Parts List
395
396
3. Preventive Maintenance
The main power button of this machine has been changed to a push-button switch (push button) from the conventional rocker switch. The push switch has characteristics and specifications different from the rocker switch. Care must be taken when replacing and adjusting parts.
Power is supplied to the machine even when the main power switch is turned OFF.
The push switch in this machine uses DC (direct current). Therefore, if the AC power cord is connected to an electrical outlet, power is supplied to the controller board, the operation unit and other modules even when the main power is turned OFF. When replacing the controller board and the operation unit in this state, not only these boards, it will damage other electrical components.
So, when performing maintenance work such as replacing parts, in addition to turning off the main power with the push switch, always unplug the AC power cord.
When you disconnect the power cord from the AC wall outlet, inside the machine there is still residual charge.
When you disconnect the power cord from the AC wall outlet, inside the machine for a while there is still residual charge. Therefore, if you remove boards in this state, it can cause a blown fuse or memory failure.
• How to remove the residual charge inside the machine
After you unplug the power cord from the AC wall outlet, in order to remove the residual charge from inside the machine, be sure to press the main power switch. Thus, the charge remaining in the machine is released, and it is possible to remove boards.
When you reconnect the AC power cord into an AC wall outlet, the machine will start automatically.
In order to remove the residual charge, push the main power switch while you disconnect the AC power cord. At that time, the power ON flag inside the machine is set. Therefore, after you finish work on the machine and reconnect the power cord to the AC, even if you do not press the main power switch, the machine will start automatically and the moving parts will begin to move. When working on moving parts, be careful that fingers or clothes do not get caught.
397
4. Replacement and Adjustment
• Automatic restart deals with cases when you accidentally unplugged the AC power cord or unexpected power outages. By keeping the power flag ON, after the resumption of power, the machine will start up automatically.
In rare cases, when you reconnect the AC power cord to a power outlet, the machine does not start automatically. In this case, the machine has not failed. The cause is due to the timing of releasing the residual charge. If you press the main power switch while the residual charge was already released, the power ON flag will not be set. At this time, start the machine manually by pressing the main power switch.
1.
Press the main power switch [A] on the machine.
398
2.
The shutdown message appears. After the shutdown process, the main power is turned off automatically.
The operation panel and the main power indicator are turned off when the machine completes the shutdown.
• Even after the shutdown message disappears, do not disconnect the power cord while the main power indicator [A] is flashing to indicate that the machine is still shutting down.
Notes on the Main Power Switch
• Before removing and adjusting electrical boards, do the following procedure. Otherwise, the board can be damaged by the residual charge inside the machine and must be replaced.
1. Take out the power cord after shutdown.
2. Press the power switch for a second to remove the residual charge inside the machine.
In case normal shutdown does not complete for some reason, the machine has a forced shutdown function.
To make a forced shutdown, press and hold the main power switch for 6 seconds.
In general, do not use the forced shutdown.
• Forced shutdown may damage the hard disk and memory, and can cause damage to the machine.
Use a forced shutdown only if it is unavoidable.
399
400
4. Replacement and Adjustment
• Turn off the main power switch and disconnect the power cord.
• After replacing, make sure that all harnesses that were removed are connected up again and secured in their clamps.
Special Tools
Item Part Number
1
4
5
6
2
3
7
A1849501
B6455020
B6455060
52039502
A2579300
C4019503
VSSG9002
8 A0929503
Description
Scanner Positioning Pin
(2pcs/set)
SD Card (1GB)
SD Card (16GB)
Silicone Grease G-501
Grease Barrierta – S552R
20× Magnification Scope
FLUOTRIBO MG GREASE:
100G
C4 Color Test Chart (3 pcs/ set)
1
1
1
1
1
1
Q’ty
1
1
Unique or Common
C (General)
C (General)
C (General)
C (General)
C (General)
C (General)
C (General)
C (General)
• A PC (Personal Computer) is required for creating the Encryption key file on an SD card when replacing the controller board in which HDD encryption has been enabled.
401
4. Replacement and Adjustment
Precaution Concerning Stabilizers
The stabilizers are necessary for meeting the requirements of IEC60950-1, the international standard for safety.
The aim of these stabilizers is to prevent the products, which are heavy, from toppling as a result of people running into or leaning onto the products, which can lead to serious accidents such as persons becoming trapped under the product. (U.S.: UL60950-1, Europe: EN60950-1)
Therefore, removal of such stabilizers must always be with the consent of the customer.
Do not remove them using only your own judgment.
402
No.
1
2
3
Cover name
Waste toner cover
Front upper cover
Front cover
No.
4
5
6
Cover name
Main power switch cover
Rear cover
Rear lower cover
Exterior Covers
No.
1
2
3
4
5
6
7
Cover name
Right upper cover
Right door
Right rear cover
Left rear cover
Controller cover
Left cover
Upper left cover
403
4. Replacement and Adjustment
No.
1
2
3
4
Cover name
Paper exit tray
Inverter tray
Paper exit cover
Paper exit lower cover
404
No.
1
2
Cover name
Paper exit front cover
Inner upper cover
No.
3
Cover name
Inner lower cover
1.
Open the front cover [A].
2.
Unhook the belt’s tip and detach the belt [A].
Exterior Covers
405
4. Replacement and Adjustment
3.
Pressing down the stopper, slide the front cover [A] to the right and detach it.
1.
Controller cover [A]
406
• Each part enclosed by a blue circle has a tab. Be careful not to damage it when attaching and detaching.
Exterior Covers
1.
Open the front cover.
2.
Paper exit tray (
)
3.
Upper left cover [A]
Slide the cover in the direction of the blue arrow.
1.
Upper left cover (
)
407
408
4. Replacement and Adjustment
2.
Left Rear Cover [A]
• Each part enclosed by a blue circle has a tab. Be careful not to damage it when attaching and detaching.
1.
Controller cover (
)
2.
Ozone filter/Dust filter box ( page 625 )
3.
Upper left cover (
)
4.
5.
Open the 2nd paper feed tray slightly.
6.
Left cover [A]
Remove it while pressing down.
Exterior Covers
409
4. Replacement and Adjustment
Order to remove
410
1. Paper exit tray
2. Controller cover
Exterior Covers
3. Ozone filter/Dust filter box
4. Front cover
5. Upper left cover
6. Left rear cover
7. 2nd paper feed tray
8. Left cover
• There are tabs (left-facing) on the back face of the rear cover. When fitting or removing the cover, take care not to damage it.
1.
Rear cover [A]
Slightly bend the cover to release the tabs behind the parts indicated by red circles and release the cover.
411
4. Replacement and Adjustment
1.
2.
Rear lower cover [A]
1.
Open the right door.
2.
Right rear cover [A] ( x4, among them, tapping screw x1)
412
• When installing, insert the projections [A] in the holes [B], taking care not to trap the harness inside.
Exterior Covers
1.
Front upper cover (
)
2.
Right upper cover [A]
1.
Open the right door.
413
414
4. Replacement and Adjustment
2.
Small cover [A]
3.
Remove the screw and the connector, and then remove the front upper cover [A].
• Remember that there are three tabs at the positions in the red arrows.
• Tilt the operation panel [B] upward to a horizontal position, and then remove the front upper cover [A].
1.
Front upper cover (
)
2.
Two connectors
Exterior Covers
3.
Bracket [A]
415
416
4. Replacement and Adjustment
4.
Proximity sensor (Human detection sensor) [A]
1.
Pull out the paper trays 1 and 2.
2.
Main power switch cover [A].
1.
Front cover (
)
2.
Open the waste toner cover [A].
Exterior Covers
417
418
4. Replacement and Adjustment
3.
Waste Toner Cover [A]
1.
Inverter Tray [A]
1.
Paper Exit Tray [A]
1.
Front upper cover (
)
2.
Paper exit tray (
)
3.
4.
Paper exit cover [A]
1.
2.
Exterior Covers
419
4. Replacement and Adjustment
3.
Connector cover [A].
4.
Paper exit lower cover [A]
420
1.
Front upper cover (
)
2.
Paper exit lower cover ( page 419 )
Exterior Covers
3.
Paper exit front cover [A]
1.
Open the front cover, and remove the belt. (
2.
Open the right door.
3.
Paper exit front cover ( page 420 )
4.
Image transfer belt unit ( page 474 )
5.
Inner upper cover [A]
1.
Front cover (
)
2.
Inner upper cover ( page 421 )
421
422
4. Replacement and Adjustment
3.
PCDU cover (Y) [A]
4.
Waste toner cover ( page 417 )
5.
Inner lower cover [A]
Smart Operation Panel
This section explains how to remove the Smart Operation Panel from the machine. For details about disassembling the Smart Operation Panel, See the service manual for Smart Operation Panel 2nd
Generation.
1.
Scanner front cover (
)
2.
Holding down both the sides of the operation panel upper cover [A], unhook the tabs
(indicated by blue circles) and remove the cover.
423
424
4. Replacement and Adjustment
3.
Operation panel [A]
4.
Open the platen cover or ADF.
5.
Spread a cloth or service mat [A] on the exposure glass to protect the display. Place the operation panel on the exposure glass so that the display faces down.
6.
Rear center cover [A]
7.
Disconnect the USB cable [A].
8.
Left small cover [A], right small cover [B]
Smart Operation Panel
425
4. Replacement and Adjustment
9.
Right hinge cover [A] (Hook x 2)
10.
Left hinge cover [A], right cover [B]
11.
Hinges [A] [B]
426
1.
2.
Scanner right cover (
)
3.
Controller box cover (
)
4.
Disconnect the USB cable [A]
5.
Remove the clamps on the cables under the scanner unit.
Smart Operation Panel
When removing a clamp, insert a long flathead screwdriver or such a tool from the side to remove it.
427
428
4. Replacement and Adjustment
• The cable has a set of 2 cable ties. When attaching the cable, position the clamp between the two cable ties.
1.
2.
Cable bracket and connector
SPDF DF3100
ADF
429
4. Replacement and Adjustment
ARDF DF3090
3.
Screws on the ADF base.
SPDF DF3100
ARDF DF3090
430
4.
Slowly and carefully (the ADF is heavy) lift the ADF [A] off the machine.
5.
Set the ADF on its edge on the floor, and then lean it against a wall [B].
ADF
• To prevent damage to the fragile feelers [A] of the ADF position sensor, never lay the ADF on a flat surface as shown below.
• If the SPDF DF3100 is being replaced, do SP4-730-002 after the new SPDF has been installed.
SP descriptions
• SP4-730-002 (FROM Main Factory Setting Execution ON/OFF)
Copies the parameters written in FROM in the SPDF to the engine board in the MFP. This SP is only for the SPDF models.
431
432
4. Replacement and Adjustment
There is no SIO (Scanner Interface Board) in this machine. The functions of the SIO of the previous machine are controlled by the IPU. Harnesses of the scanner unit connect directly to the IPU in the controller box on the back of the machine.
1.
Scanner front cover [A]
1.
Remove the screw.
2.
Scanner right cover [A]
Remove the hook at the top, and then slide the cover towards the rear.
Scanner Unit
1.
Scanner front cover (
)
433
4. Replacement and Adjustment
2.
Scanner left cover [A]
1.
Platen cover or ADF
2.
3.
Scanner Upper Cover [A]
434
1.
Open the platen cover or ADF.
2.
Scanner right cover (
)
3.
Scale [A]
4.
Sheet-through exposure glass [A]
5.
Rear scale [A]
Scanner Unit
435
4. Replacement and Adjustment
6.
Left scale and exposure glass [A]
• The exposure glass and the left scale are attached with double-sided tape.
• When installing, please follow the points below:
• Install the sheet-through exposure glass with the mark [A] at the rear left corner.
• Set so that the locating hole of the left scale fits over the locating boss of the front/rear frame.
436
1.
2.
Scanner front cover (
)
3.
Scanner carriage front cover [A]
4.
Move the scanner carriage [A] to the indicated position as shown.
Scanner Unit
437
4. Replacement and Adjustment
5.
Loosen the screw, remove the spring [A], and then remove the belt [B].
438
6.
Turn the scanner carriage over and place it on the frame [A].
• When holding the scanner carriage, be careful not to touch the circuit board [A], lens [B], and mirror [C].
7.
Belt [A]
8.
Lower the lock lever [A] and disconnect the FFC [B].
9.
Ferrite core [A], Mylar sheet [B] (Hook x 4)
10.
Scanner carriage
Scanner Unit
439
440
4. Replacement and Adjustment
• When attaching the scanner carriage, hold the carriage with the screw [A] loosened and move the carriage back and forth to the sides twice to have the belt stretch evenly. Then, fasten the screw [A].
• After replacing the scanner carriage, enter the values supplied with the carriage in the following SP
- SP4-871-002 (Distortion Correction Distortion Initialization)
- SP4-880-001 (Dot shift amount between R Line and G Line).
- SP4-880-002 (Dot shift amount between G Line and B Line).
To apply the specified settings, turn the power off and then back on.
The specified values are cleared when the NVRAM is initialized, so be sure to keep the supplied sheet showing the values in the machine.
1.
2.
Scanner carriage front cover [A]
3.
Move the scanner carriage [A] to the indicated position as shown.
Scanner Unit
4.
Resin cover [A] (Hook x 3)
441
4. Replacement and Adjustment
5.
Open the metal cover [A]
6.
Wipe clean the mirror with a dry cloth.
442
• When reattaching the metal cover [A], fasten the screws in the order of "1", "2", and "3".
• When attaching the resin cover, insert its tip under the metal frame.
Scanner Unit
1.
Scanner upper cover (
)
2.
3.
Grounding plate [A]
443
444
4. Replacement and Adjustment
4.
Spring [A]
5.
Scanner motor with bracket [A]
6.
Bracket [A]
1.
2.
APS sensor harness cover [A]
3.
APS sensors [A] (Hook x 4)
1.
Scanner Unit
445
4. Replacement and Adjustment
2.
Slide the scanner carriage [A] in the direction of the arrow.
3.
Scanner HP Sensor [A] (Hook x 3)
446
1.
Scanner upper cover (
)
2.
ARDF/Platen cover sensor [A]
1.
2.
Remove the FFC from the scanner carriage (
)
3.
Original size sensor harness cover [A]
Scanner Unit
447
4. Replacement and Adjustment
4.
Remove the double-sided tape.
When reattaching the same part, apply a double-sided tape again.
5.
6.
Controller box cover (
)
7.
While pressing the lock release lever, pull out the FFC [A].
448
When changing the FFC, stick the Mylar [A] to the new FFC.
Scanner Unit
When attaching the Mylar, follow the steps below.
1.
Feed the FFC through the ferrite core [A].
2.
Connect the FFC to the scanner carriage’s connector, and then lift the lever [A] to lock it.
449
4. Replacement and Adjustment
3.
Attach the Mylar [A] to the FFC from above, and then insert the tabs at both ends of the
Mylar into the gaps in the FFC holder to secure it in position.
450
When applying the Mylar, be sure not to stretch the FFC.
Applying the Mylar while stretching the FFC causes the circuit board to be deformed.
Scanner Unit
451
4. Replacement and Adjustment
• Turn off the main power switch and unplug the machine before beginning any of the procedures in this section. Laser beams can cause serious eye injury.
• Caution Decals
• Decal Location
452
• A polygon mirror motor protection bracket and a red tag are attached to each new laser unit.
Remove these before you install the new unit.
1.
Remove the polygon mirror motor cover [A] from the new laser unit.
Laser Unit
2.
Polygon mirror motor bracket [A], Red tag [B]
3.
Reattach the polygon mirror motor cover.
1.
2.
Laser unit [A]
453
4. Replacement and Adjustment
1.
Insert the new laser unit in the main body carefully.
2.
Connect all harnesses except the laser optics positioning motor harness [A] (2nd from right).
454
3.
Reassemble the machine.
Laser Unit
1.
Close the front cover and attach the left cover.
• Attach the left cover before turning on the main power switch. Laser beams can seriously damage your eyes.
2.
Plug in and turn on the main power switch.
3.
Download the data of the new laser unit to the main body with SP2-110-005.
4.
Check that SP2-119-001 to 003 is "0."
• If it is not "0", perform SP2-110-005 again.
• If it is not executed correctly, outputs will be abnormal (magnification and color registration errors), and SC 285 may occur.
5.
Turn off the main power switch and disconnect the power cord.
6.
Remove the left cover and attach the laser optics positioning motor harness [A].
7.
Close the left cover.
8.
Plug in and turn on the main power switch.
9.
Select [14: Trimmed area] in SP2-109-003, and then press [OK].
10.
Press [Copy Window], and then print the test pattern in the copy screen.
• Check if the margin on either side on the output (14: Trimmed area) is less than 4±1 mm or not. If it is not within these limits, change the reference value (Bk) of the main scanning magnification adjustment (SP2-102-001 to -003).
455
456
4. Replacement and Adjustment
• Adjust the values of the main scanning magnification only for Bk (black). It is not necessary to adjust other color’s values (cyan, magenta, yellow) because other colors are automatically adjusted in relation to the setting for Bk.
• Input the same value for each SP (SP2-102-001 to -003) even though there are three SPs of the main scanning magnification adjustment for the standard, middle and low line speed which are used for each paper type.
• Check if the margin on the left side on the output (14: Trimmed area) is less than 2±1 mm or not. If it is not within these limits, change the reference value (Bk) of the registration adjustment
(SP2-101-001).
11.
Set SP2-109-003 to "0: None" after adjusting the main scanning magnification and registration.
12.
Perform line adjustment.
SP2-111-004: Forced Line Position Adj. Mode d
The result can be checked with SP2-194-007 (MUSIC Execution Result Execution Result) (0:
Success, 1: Failure).
Also, results for each color can be checked with SP2-194-010 to 013 (1: Completed successfully).
13.
Exit the SP mode.
1.
2.
Polygon mirror motor cover [A]
3.
Polygon mirror motor holder [A], Polygon mirror motor [B]
Laser Unit
SP2-111-004: Forced Line Position Adj. Mode d
The result can be checked with SP2-194-007 (MUSIC Execution Result Execution Result) (0: Success, 1:
Failure).
Also, results for each color can be checked with SP2-194-010 to 013.
SP2-110-005 (Writing Unit Adj. Transfer)
Execution flag to download adjustment values of laser unit to the main unit’s SP.
Must be executed when replacing the laser unit or assembling the main unit.
SP2-119-001 to 003 (Skew Adjustment Display)
Displays the current skew correction value for each color.
SP2-109-003 (Test Pattern: Pattern Selection)
Selects the test pattern.
SP2-102-001 to -003 (Magnification Adjustment: Bk)
Adjusts main scan lower speed scale for BK.
Value increase: image stretches.
Value decrease: image shrinks
CMY color scale will fit to standard BK speed after executing MUSIC; BK color will have a different scale in the image without executing MUSIC after this SP.
457
458
4. Replacement and Adjustment
SP2-101-001 (Registration Correction: Color Main Dot: Bk)
Adjusts main scan registration for BK.
Value increase: image shifts to the right facing the paper.
Value decrease: image shifts to the left facing the paper.
CMY colors are adjusted to the BK color position if MUSIC is done after this SP.
SP2-111-004 (Forced Line Position Adj. Mode d)
Executes the fine line position adjustment and rough line position adjustment.
SP2-194-007 (MUSIC Execution Result Execution Result)
Displays the result of MUSIC adjustment.
0: Success, 1: Failure
SP2-194-010 to 013 (MUSIC Execution Result: Error Result C, M, Y, K)
Displays the result code of MUSIC adjustment for each color.
Detection Result
0
1
2
3
4
5
Meaning
MUSIC not executed
Correction Succeeded: Sampling is conducted correctly and the correction is completed
Sampling Failed (When the MUSIC pattern failed to be detected)
Detection Patterns Lacking (When the number of lines detected is smaller than the fixed number)
The sampled data is beyond the correction range.
(Calculated correction value is just out of range)
The sampled data is beyond the correction range.
RTB 24
Agitate the developer by shaking the unit
• When installing a complete brand-new PCDU, it is not necessary to set SP3-701: New
Development Unit detection
1.
Open the front cover [A].
PCDU
2.
Image Transfer front cover [A]
459
460
4. Replacement and Adjustment
3.
PCDU cover.
[A]
[B]
Y
M
x 1
x 1
[C] C x 1
[D] K x 1
4.
Release the lock of the image transfer contact lever [A].
PCDU
5.
PCDU.
[A]
[B]
[C]
[D]
Y
M
C
K
x 1, x 1,
x 1, x 1,
x 1, x 1,
x 1, x 1,
x 1
x 1
x 1
x 1
• When attaching the PCDU, clamp the harness so that the bind [A] comes above the clamp.
1.
Turn ON the main power.
2.
Do the "Automatic Color Calibration (ACC)" for the copier mode & printer mode as follows:
1. "User Tools" icon > "Machine Features" > "Maintenance" > "Auto Color Calibration" > "Start"
461
462
4. Replacement and Adjustment
2. Print the ACC test pattern.
3. Put the printout on the exposure glass.
4. Put 10 sheets of white paper on the test chart. This ensures the precise ACC adjustment.
5. Close the SPDF/ARDF or the platen cover.
6. Press "Start Scanning" on the LCD. Then, the machine starts the ACC.
3.
Exit the User Tools mode.
• In the PCU for MP C2504/C2004 and the PCU for MP C6004/C5504/C4504/C3504/
C3004, the charging method is different. Variations in the charge voltage must be corrected when a PCU is replaced.
• Because of this, before replacing a PCU, do the procedure shown below. The main points are as follows.
• Input the charge voltage correction value for the new PCU.
• The machine will optimize SP settings related to imaging using process control, after you input the charge voltage correction value and replace the PCU.
1.
Set SP3-701: New PCU detection to “1” before replacing the PCU.
SPs for manual new unit
Item SP
Black: SP3-701-002
Cyan: SP3-701-025
PCU
Magenta: SP3-701-048
Yellow: SP3-701- 071
0: new unit detection flag OFF, 1: new unit detection flag ON
2.
Check the charge voltage correction value printed on the label attached to the new PCU.
This value is adjusted for each PCU.
• When installing a complete brand-new PCDU, it is not necessary to input the correction value.
PCDU
C
D
A
B
Bar code
PCU Lot No.
Correction value
Last three digits of SP number
E SP No.
3.
Input the value (located at [C] on the decal as shown above) into SP2-005 as shown below.
SPs for charge voltage correction before replacing PCU
SP No. (SP name)
K
C
M
SP2-005-235 (Correction Coefficient c1: K)
SP2-005-236 (Correction Coefficient c1: C)
SP2-005-237 (Correction Coefficient c1: M)
Y SP2-005-238 (Correction Coefficient c1: Y)
4.
Check SP2-005 to make sure that you have input the correct values. Check that they are the same as the values on the labels in step 2.
5.
Turn the power OFF.
6.
Replace the PCU.
7.
Turn the power ON. (Process control is done automatically.)
• If you replace the PCU without inputting the correction value, do the following procedure:
• Case 1: When you set SP3-701 to “1”
1. Input the PCU correction value.
2. Execute process control manually with SP3-011-001 in order to adjust the machine settings with the PCU correction value.
463
464
4. Replacement and Adjustment
• Case 2: When you did not set SP3-701 to “1”
1. Set SP3-701 to “1”.
2. Input the PCU correction value.
3. Turn the power OFF. Note that process control will start automatically.
RTB 24
Agitate the developer by shaking the unit
1.
Set SP3-701: New unit detection to “1” before replacing the development unit.
SPs for manual new unit
Item SP
Black: SP3-701-003
Cyan: SP3-701-026
Development unit
Magenta: SP3-701-049
Yellow: SP3-701- 072
0: new unit detection flag OFF, 1: new unit detection flag ON
2.
Switch the power OFF. Then replace the development unit and switch the power ON.
• Replacing the development unit resets not only the development unit counter, but also the PCU counter. However, if you change the SP setting (SP3-701) before you replace the development unit, the PM counter of the development unit is reset, but the PM counter of the PCU is not reset.
• Therefore, before you replace the development unit, the manual new unit setting SP3-701 must be done. Doing these in the wrong order will reset the counter of the PCU also.
1.
2.
Release the connecting part (front) [A] ( x 2) and harness [B].
PCDU
3.
Cover [A] ( x 1).
• Be careful not to break the plate (shown by the red arrow).
• Handle with care to prevent deformation of the plate. Deformation can cause unstable images due to contact failure. Be sure to attach this cover to the PCDU and install the PCDU in the mainframe.
465
4. Replacement and Adjustment
4.
Connecting part (rear) [A] ( x 3).
5.
Separate PCU [A] and development unit [B].
466
• When holding the development unit, be sure to obey the following three DO NOTs:
PCDU
• DO NOT touch the development roller housing [A]. Doing so will deform the development roller housing, which causes the development roller to be scratched.
• DO NOT touch the doctor blade [B]. The doctor blade is an extremely sharp-edged blade, made with a high precision to work properly. So touching the blade causes physical injury as well as deformation of the blade assembly which causes a malfunction of the development unit.
• DO NOT touch the development roller. Doing so develops a fingerprint on the paper.
• Hold the development unit as shown below:
• When separating the PCU and development unit, the drum may come off and this could cause a toner spillage. Hold the PCU [A] with the drum side up as shown below to prevent toner spillage.
467
4. Replacement and Adjustment
Pay close attention not to spill any toner on the charge roller when assembling.
• Remove the heat seal [A] after replacing the PCDU.
• Remove the cap [B] pasted on the toner port when replacing the PCDU.
468
Before installing, rotate the drum in the blue arrow direction, to ensure that toner lines do not occur.
PCDU
1.
Turn ON the main power.
2.
Do the "Automatic Color Calibration (ACC)" for the copier mode & printer mode as follows:
1. "User Tools" icon > "Machine Features" > "Maintenance" > "Auto Color Calibration" > "Start"
2. Print the ACC test pattern.
3. Put the printout on the exposure glass.
4. Put 10 sheets of white paper on the test chart. This ensures the precise ACC adjustment.
5. Close the SPDF/ARDF or the platen cover.
6. Press "Start Scanning" on the LCD. Then, the machine starts the ACC.
3.
Exit the User Tools mode.
1.
Toner supply cooling fan unit ( page 630 )
2.
Controller box (
)
469
470
4. Replacement and Adjustment
3.
Duct [A]
4.
Connector [A]
5.
Image Transfer Belt Unit ( page 474 )
6.
PCDU (K) (
)
7.
Imaging temperature sensor harness guide [A] and Imaging temperature sensor [B] (
×2).
PCDU
471
472
4. Replacement and Adjustment
When the bottle is replaced after the machine detects that the waste toner bottle is full and stops, the counter for the Waste Toner Bottle is reset automatically.
When the bottle is replaced before the machine stops due to a full bottle, it is necessary to reset the PM counter manually (set SP3-701-142 to “1” before replacing the bottle, then switch the power off).
SP3-701 (Manual New Unit Set)
This SP is the new unit detection flag.
0: new unit detection flag OFF, 1: new unit detection flag ON
Item SP
Waste toner bottle SP3-701-142
1.
Open the waste toner cover [A].
2.
Pull out the waste toner bottle [A].
3.
Replace the waste toner bottle.
Waste Toner
473
4. Replacement and Adjustment
• Note that if the two levers [A] [B] are not pointing up, the image transfer belt unit cannot be inserted.
474
• Before you remove or attach the image transfer belt unit, open the right door and the paper transfer unit.
• Do not touch the rollers but hold the upper/lower resin parts [A] when you lift the Image Transfer
Unit. Touching the rollers may cause poor image quality.
Image Transfer Unit
• Precautions when attaching the image transfer belt unit:
• Slowly push the unit until it is inserted all the way, and then give a final strong push one more time. Then lock the ITB lock lever and ITB contact lever.
If the ITB contact lever is locked with the image transfer belt unit not fully inserted into the machine, the paper transfer roller is not set in the correct position when the paper transfer roller unit is closed. This causes shadows on the image or paper jam, and the paper transfer roller unit may not open.
Before replacing the Image Transfer Belt unit, set SP3-701-093 to "1" and switch the power OFF.
Then replace the Image Transfer Belt unit and switch the power ON.
SP3-701 (Manual New Unit Set)
This SP is the new unit detection flag.
0: new unit detection flag OFF, 1: new unit detection flag ON
Item
Image Transfer Belt Unit SP3-701-093
SP
1.
Open the front cover.
475
476
4. Replacement and Adjustment
2.
Image transfer front cover [A]
3.
Release the lock [A] and open the right door [B].
4.
Pull the handle [A] and open the paper transfer unit [B].
Image Transfer Unit
5.
Release the ITB lock lever [A] and ITB contact lever [B].
6.
Pull out the image transfer belt unit fully [A].
477
4. Replacement and Adjustment
7.
Lift the handle [B] to release the lock, and remove the image transfer belt unit.
Locking mechanism by handle
478
• Before removing the image transfer cleaning unit [A], turn the assembly upside down (as shown on the right), so that the image transfer cleaning unit [A] is underneath the image transfer belt unit [B].
This prevents scattering of toner.
Image Transfer Unit
• When replacing the Image Transfer Cleaning Unit, do not touch the cleaning blade edge.
Before replacing the Image Transfer Belt Cleaning, set SP3-701-102 to "1" and switch the power OFF.
Then replace the Image Transfer Belt Cleaning and switch the power ON.
SP3-701 (Manual New Unit Set)
This SP is the new unit detection flag.
0: new unit detection flag OFF, 1: new unit detection flag ON
479
480
4. Replacement and Adjustment
Item
Image Transfer Cleaning Unit
1.
Image transfer belt unit ( page 474 )
2.
Image transfer lock unit [A]
SP3-701-102
SP
3.
Remove the screws above the image transfer cleaning unit [A].
Image Transfer Unit
4.
Turn the whole image transfer belt unit over, and remove the screws below the image transfer cleaning unit.
5.
While releasing the hook, lift the image transfer belt unit gently, and remove the image transfer cleaning unit.
481
482
4. Replacement and Adjustment
6.
Put toner on the image transfer belt.
[A]: 20mm or more
[B]: About 5mm
• It is not necessary to specify the color of the toner, though yellow toner is used in the above example.
7.
Attach the image transfer cleaning unit.
8.
Rotate the image transfer belt about 10mm [A] in the reverse direction, then turn it forward one complete turn [B].
Image Transfer Unit
• Do not touch the rollers but hold the upper/lower resin part [A] when you lift the Image Transfer
Unit. Touching the rollers may cause poor image quality.
1.
Image transfer belt unit ( page 474 )
2.
Bracket [A]
483
484
4. Replacement and Adjustment
3.
Brackets [A] [B]
4.
Image transfer cleaning unit (
)
5.
Remove the tension fixing frames [A] and [B] (front side: black, rear side: gray).
6.
Position the image transfer unit with the front side underneath.
7.
Rotate the gear [A] to change to the OPEN position.
The part in the red circle opens.
Image Transfer Unit
8.
Release the tension, and remove the belt.
485
486
4. Replacement and Adjustment
• When attaching the belt, make sure that there is no foreign material on it.
• Make sure to attach the belt with the edge with markings (2 white dots) at the unit’s rear.
• Be careful not to bend or scratch the belt.
1.
Place the image transfer unit upright with its front face down, and then attach the belt from the top.
Make sure to have the belt’s edge with markings (2 white dots) positioned at the top (unit’s rear).
2.
Holding the resin parts on the top and bottom, place the unit on its side.
3.
Adjust the belt position according to the following two points:
• The belt must be attached between the flanges [A] at both ends of the tension roller.
• The belt’s edge must be between the two lines [B] on the frame.
4.
Apply tension back to normal.
5.
Rotate the gear [A] to change to the CLOSED position.
The part in the red circle closes.
Image Transfer Unit
487
4. Replacement and Adjustment
6.
Attach the tension fixing frames [A] and [B] (front side: black, rear side: gray).
7.
Put toner on the image transfer belt.
488
[A]: 20mm or more
[B]: About 5mm
• It is not necessary to specify the color of the toner, though yellow toner is used in the example above.
8.
Attach the image transfer cleaning unit. (Refer to page 478 )
Image Transfer Unit
9.
Rotate the image transfer belt about 10mm [A] in the reverse direction, then turn it forward one complete turn [B].
10.
Attach the brackets [A] [B]
489
4. Replacement and Adjustment
11.
Attach the bracket [A]
12.
Attach the image transfer lock unit [A].
490
13.
Install the image transfer unit on the machine.
After replacing the image transfer belt, to prevent twisting of the belt, pass the belt round once in the direction of the arrow.
1.
Open the right door.
2.
Pull the handle [A] and open the paper transfer unit [B].
Image Transfer Unit
491
4. Replacement and Adjustment
3.
Paper transfer roller [A]
When reinstalling the paper transfer roller, do not install the wrong type of roller.
492
[A]: Standard roller
[B]: Imageable Area Extension Unit Type M19
When attaching the paper transfer roller, make sure that the roller is set in the correct position while referring to the three points described below.
• If the paper transfer roller is set incorrectly, the following problems may occur.
• Damage to the image transfer belt
• Roller detachment when opening and closing the paper transfer roller unit to remove a paper jam
• The paper transfer roller unit does not open
1. Check that the claw [A] on the roller holder is under the guide plate [B].
Image Transfer Unit
2. Check that the pin [A] on either end of the paper transfer roller is inserted correctly.
493
4. Replacement and Adjustment
494
3. Check that the spring [A] at either end of the paper transfer roller unit is in the correct position at each end.
Image Transfer Unit
Before replacing the Image Paper Transfer Roller Unit, set SP3-701-109 to "1" and switch the power
OFF. Then replace the Image Paper Transfer Roller Unit and switch the power ON.
SP3-701 (Manual New Unit Set)
This SP is the new unit detection flag.
0: new unit detection flag OFF, 1: new unit detection flag ON
Item
Paper Transfer Roller Unit SP3-701-109
SP
1.
Open the right door.
495
496
4. Replacement and Adjustment
2.
Remove the right clip ring and connector on the rear side.
3.
Pull the handle [A] and open the paper transfer unit [B].
Image Transfer Unit
4.
Remove the left clip ring at the front side, and remove the paper transfer roller unit [A].
• Note that the sizes of the clip ring differ on the left and right.
• When attaching a paper transfer roller unit, first attach the bushings [A] to the paper transfer roller unit.
497
4. Replacement and Adjustment
1.
Open the right door.
2.
Fusing entrance sensor unit [A]
3.
Fusing entrance sensor [A]
498
Each sensor assembly has a list of characteristic values attached to it. Before you replace the TM/ID sensor, you must do the following procedure, or process control/MUSIC will not be done correctly after power is switched on (it will use the values for the old sensor).
Image Transfer Unit
• The characteristic values attached to the service part must be entered before replacement. It is recommended that in case Process control/MUSIC after replacement is not completed successfully, take a note of values of SP3-333, SP3-334 and SP3-335.
1.
Note the characteristic values that are listed on the bar code label.
• TM/ID Sensor (front): F, TM/ID Sensor (center): C, TM/ID Sensor (rear): R, be careful.
2.
Turn on the main power switch, and then go into the SP mode.
3.
Input the characteristic values.
Input data for TM/ID Sensor: F into SP3-333. Input data for TM/ID sensor: C into SP3-334. Input data for TM/ID sensor: R into SP3-335.
SP No.
Classification 1
3-333-001 ID.Sens TestVal:F
3-333-002 ID.Sens TestVal:F
3-333-003 ID.Sens TestVal:F
3-333-004 ID.Sens TestVal:F
3-333-005 ID.Sens TestVal:F
3-333-006 ID.Sens TestVal:F
3-334-001 ID.Sens TestVal:C
3-334-002 ID.Sens TestVal:C
3-334-003 ID.Sens TestVal:C
3-334-004 ID.Sens TestVal:C
3-334-005 ID.Sens TestVal:C
Classification 2
K2: Check
Diffuse Corr
Vct_reg Check:Slope
Vct_reg Check:Xint
Vct_dif Check:Slope
Vct_dif Check:Xint
K2: Check
Diffuse Corr
Vct_reg Check:Slope
Vct_reg Check:Xint
Vct_dif Check:Slope
Value
TM/ID sensor: F, value of [1]
TM/ID sensor: F, value of [2]
TM/ID sensor: F, value of [3]
TM/ID sensor: F, value of [4]
TM/ID sensor: F, value of [5]
TM/ID sensor: F, value of [6]
TM/ID sensor: C, value of [1]
TM/ID sensor: C, value of [2]
TM/ID sensor: C, value of [3]
TM/ID sensor: C, value of [4]
TM/ID sensor: C, value of [5]
499
500
4. Replacement and Adjustment
SP No.
Classification 1
3-334-006 ID.Sens TestVal:C
3-335-001 ID.Sens TestVal:R
3-335-002 ID.Sens TestVal:R
3-335-003 ID.Sens TestVal:R
3-335-004 ID.Sens TestVal:R
3-335-005 ID.Sens TestVal:R
3-335-006 ID.Sens TestVal:R
Classification 2
Vct_dif Check:Xint
K2: Check
Diffuse Corr
Vct_reg Check:Slope
Vct_reg Check:Xint
Vct_dif Check:Slope
Vct_dif Check:Xint
Value
TM/ID sensor: C, value of [6]
TM/ID sensor: R, value of [1]
TM/ID sensor: R, value of [2]
TM/ID sensor: R, value of [3]
TM/ID sensor: R, value of [4]
TM/ID sensor: R, value of [5]
TM/ID sensor: R, value of [6]
1.
Image transfer belt unit ( page 474 )
2.
Paper transfer roller unit ( page 495 )
3.
Fusing unit (
)
4.
TM/ID sensor unit [A]
• When installing the TM/ID sensor unit.
• 1. Attach the screw of the front side [B]
• 2. Attach the screw of the back side [C]
• When installed in reverse order, an SC may occur because the sensor position has shifted.
5.
Disconnect the connectors.
Image Transfer Unit
501
4. Replacement and Adjustment
6.
TM/ID sensor [A]
502
1.
Turn on the main power switch, and then go into the SP mode.
2.
Run SP3-011-004 (Manual Procon: Exe Full MUSIC).
• If the SP3-011-004 can't finish successfully, make sure you are entering the correct value into the SP.
Related SPs
• SP3-011-004 (Manual ProCon :Exe: Full MUSIC)
Executes Process Control and full MUSIC.
• SP3-012-001 to 010 (ProCon OK?: Front)
Displays the past 10 Process Control result codes detected by the front TM/ID sensor. The code is 2 digits per color from the left, in the order of YMCK.
• SP3-012-011 to 020 (ProCon OK?: Center)
Displays the past 10 Process Control result codes detected by the center TM/ID sensor. The code is 2 digits per color from the left, in the order of YMCK.
• SP3-012-021 to 030 (ProCon OK?: Rear)
Displays the past 10 Process Control result codes detected by the rear TM/ID sensor. The code is 2 digits per color from left, in the order of YMCK.
ProCon results code
Category
00 and larger
Code Result name
00 Not executed
Description
Factory default setting (SP default)
Image Transfer Unit
Category
10 and larger
Result (Normal)
Code
11
Result name
Succeeded
40 and larger
ID Sensor
41 ID sensor output error (Max)
42 ID sensor output error (Min)
43 ID Sensor error (Max)
45 and larger
ID Pattern detection
44 ID Sensor error (Min)
45 ID Pattern extract error
50 Vmin_Bk/K2 error (Max)
51 Vmin_Bk/K2 error (Min)
52 K5 error (Max)
53 K5 error (Min)
54
K5 calculated approximate point error
55
56
Development gamma error
(Max)
Development gamma error
(Min)
57
58
Start developing voltage: Vk error(Max)
Start developing voltage: Vk error(Min)
59 Not enough valid data
-
Description
Vt > Max
Vt < Min
Development gamma is in target, but
Vt value is less than upper limit.
Development gamma is in target, but
Vt value is less than lower limit.
Cannot detect ID Pattern
K:Vmin_Bk / CMY:K2 > Max
K:Vmin_Bk / CMY:K2 < Min
K5 > Max
K5 < Min
K5 calculated approximate point <
Min
Development gamma > Max
Development gamma < Min
Start developing voltage: Vk > Max
Start developing voltage: Vk < Min
Adhesion amount data for development gamma calculation point is under 2.
503
504
4. Replacement and Adjustment
Category
90 and larger
Result(End)
Code Result name
90 Potential not adjusted
99 Stopped
• Execution result example (In order of YMCK from left)
• Factory default (SP default): [00,00,00,00]
• Starting adjust: [99,99,99,99]
• Fail Vsg adjust(Y): [21,99,99,99]
• Error of Development gamma Max(C): [99,99,55,99]
• Succeeded: [11,11,11,11]
1.
Remove the 1st and 2nd paper tray.
2.
Main power switch cover [A]
Description
Potential control method is set as
[0:FIX].
Stopped by door open, power off, error. (Set when execute.)
Image Transfer Unit
3.
Insert a screwdriver through the hole in the frame, and detach the temperature and humidity sensor together with its bracket [A].
4.
Temperature and humidity sensor [A]
1.
Image transfer belt unit ( page 474 )
2.
505
4. Replacement and Adjustment
3.
ITB contact and release sensor bracket [A]
4.
ITB contact and release sensor [A]
506
1.
Open the front cover.
2.
Image transfer front cover [A]
3.
Release the ITB lock lever [A].
Image Transfer Unit
507
508
4. Replacement and Adjustment
4.
Image transfer lock unit [A]
• When installing the image transfer lock unit, release the ITB lock lever and follow the procedures below, taking care to avoid deformation of the pin inside the unit (circled in red below).
If the pin is deformed, the shutter on the waste toner recovery path may not open and waste toner may clog the cleaning unit.
Image Transfer Unit
1.
Before installing, check that the lever on the image transfer lock unit is in the unlocked position.
Unlocked position:
2.
Install the image transfer lock unit [A] so that the gear [B] on the image transfer unit side fits into the space in the image transfer lock unit circled in blue below.
509
510
4. Replacement and Adjustment
3.
Return the ITB lock lever [A] to the locked position.
Drive Unit
No.
Description
1 Paper feed motor
2 Transport motor
3 Registration motor
4 Paper exit/ Pressure release motor
5 Fusing motor
No.
Description
6 Paper transfer contact and release motor
7 PCU motor: CMY
8 Development motor: CMY
9 Development solenoid
10 PCU motor: Black/ ITB drive motor
511
4. Replacement and Adjustment
1.
Power supply box (
)
2.
Paper Feed Motor [A]
1.
Power supply box (
)
2.
Transport motor [A]
512
1.
Controller box (
)
2.
Paper transfer contact and release motor unit [A]
Drive Unit
1.
Controller box (
)
2.
Power supply box (
)
3.
4.
Bracket [A]
5.
Toner supply cooling fan unit ( page 630 )
513
4. Replacement and Adjustment
6.
Duct [A]
7.
Imaging drive unit [A]
514
1.
Controller box (
)
2.
PCU Motor: CMY [A]
1.
Controller box (
)
2.
Power supply box (
)
3.
4.
Bracket [A]
Drive Unit
515
516
4. Replacement and Adjustment
5.
Development Motor: CMY [A]
1.
Controller box (
)
2.
Power supply box (
)
3.
4.
Bracket [A]
5.
Development solenoid cover [A]
6.
Development solenoid [A]
1.
Controller box (
)
2.
Power supply box (
)
3.
Drive Unit
517
4. Replacement and Adjustment
4.
Bracket [A]
5.
PCU motor: Black / ITB drive motor [A]
518
1.
Controller box (
)
2.
Power supply box (
)
3.
4.
Bracket [A]
5.
Registration motor [A]
1.
Controller box (
)
Drive Unit
519
4. Replacement and Adjustment
2.
Fusing motor [A]
1.
Fusing exhaust fan unit (
)
2.
Paper exit / Pressure release motor [A]
520
1.
Paper exit unit (
)
2.
Fusing exhaust fan unit (
)
3.
Duplex entrance motor unit [A]
4.
Duplex entrance motor [A]
1.
Controller box (
)
2.
Toner supply cooling fan unit ( page 630 )
Drive Unit
521
4. Replacement and Adjustment
3.
Duct [A]
4.
Toner supply motor
522
[A]
[B]
[C]
[D]
M
Y
K
C
×2, ×1
×2, ×1
×2, ×1
×2, ×1
• When removing the sub hopper, be careful not to tilt it to avoid spilling the toner inside the hopper.
• When replacing the sub hopper because of clogged toner, replace the toner duct[A], too.
Drive Unit
1.
Pull out the image transfer belt unit about 5cm.
2.
Controller box (
)
3.
Toner supply cooling fan unit ( page 630 )
523
524
4. Replacement and Adjustment
4.
Duct [A]
5.
Toner supply motor unit (K) [A]
6.
Sub hopper (K) [A]
1.
Pull out the image transfer belt unit about 5cm.
2.
Controller box (
)
3.
Toner supply cooling fan unit ( page 630 )
4.
Duct [A]
5.
Harness guide [A]
Drive Unit
525
4. Replacement and Adjustment
6.
Toner supply motor unit (C) [A]
7.
Sub hopper (C) [A]
526
1.
Controller box (
)
2.
Harness guide [A]
3.
Toner supply motor unit (M) [A]
Drive Unit
527
528
4. Replacement and Adjustment
4.
Sub hopper (M) [A]
1.
Controller box (
)
2.
Harness guide [A]
3.
Toner supply motor unit (Y) [A]
4.
Sub hopper (Y) [A]
1.
Sub Hopper (
)
Drive Unit
529
4. Replacement and Adjustment
2.
Toner end sensor [A]
530
• The toner end sensors are the same for each color.
1.
Toner supply motor/K (
)
2.
Toner bottle drive motor/K [A]
1.
Toner supply motor/C ( page 521 )
2.
Toner bottle drive motor/C [A]
1.
Toner supply motor/M ( page 521 )
Drive Unit
531
4. Replacement and Adjustment
2.
Toner bottle drive motor/M [A]
1.
Toner supply motor/Y ( page 521 )
2.
Toner bottle drive motor/Y [A]
532
1.
Toner bottle drive motor/K ( page 530 )
2.
Toner bottle drive motor/C (
)
3.
ID chip contact board (K) [A]
1.
Toner bottle drive motor/C (
)
2.
Toner bottle drive motor/M (
)
3.
ID chip contact board (C) [A]
1.
Toner bottle drive motor/M (
)
2.
Toner bottle drive motor/Y ( page 532 )
Drive Unit
533
534
4. Replacement and Adjustment
3.
ID chip contact board (M) [A]
1.
Toner bottle drive motor/Y ( page 532 )
2.
ID chip contact board (Y) [A]
Drive Unit
1.
Image transfer belt unit ( page 474 )
2.
3.
Toner bottle drive motor ( page 530 )
4.
Sub hopper (
)
5.
ID chip contact board ( page 532 )
6.
Put a piece of disposable paper [A] on the inside of the machine to avoid damage due to toner spillage.
7.
Put a piece of disposable paper [A] under the transport coil to avoid damage due to toner spillage.
535
536
4. Replacement and Adjustment
8.
Remove all the harnesses connecting to the transport coil unit ( ×8).
9.
Remove the screws fixing the transport coil units [A] ( ×5, each color).
10.
Release the claws for the transport coil units [A] (claw ×1, each color).
11.
Remove the screws securing the bracket [A] ( ×2).
Drive Unit
12.
Put a piece of disposable paper on the floor because toner can spill when you put the transport coil unit down.
13.
Pull out the whole transport coil unit [A] together with the bracket [B].
• Be sure to put a piece of disposable paper on the floor because toner can spill when you put the transport coil unit down.
537
4. Replacement and Adjustment
14.
Transport coil unit for (Y) [A] (tab×1).
538
1.
See steps 1 to 13 in the transport coil replacement procedure for “Y”. (
)
2.
Transport coil unit for (M) [A] (tab×1).
1.
See steps 1 to 13 in the transport coil replacement procedure for “Y”. (
)
2.
Transport coil unit for (C) [A] (tab×1).
Drive Unit
1.
See steps 1 to 13 in the transport coil replacement procedure for “Y”. (
)
539
540
4. Replacement and Adjustment
2.
Transport coil unit for (K) [A] (tab×1).
Fusing Unit
• Because there is a danger of burns on contact with hot parts of the fusing unit, start work when the temperature drops to a low enough temperature.
• To clear SC544-02 or SC554-02, replacing the fusing unit or installing a fuse (provided in the
fusing sleeve belt unit) in the fusing unit must be required. Refer to page 973 "When SC544-02,
SC554-02 (Non-contact Thermistor High Temperature Detection) Is Displayed".
• Fusing unit has a new unit detection mechanism, so it is not necessary to set SPs (New Unit
Detection).
• When the fusing unit is used past its target yield (400k), the fusing unit may break, causing a service call. Therefore, the machine displays a warning on the operation panel at 415k pages and stops at 430k pages.
1.
Open the right door.
2.
Pull the handle [A] and open the paper transfer unit [B].
541
4. Replacement and Adjustment
3.
Fusing unit [A]
• To attach the fusing unit, fasten the screws in the order [B] (rear), [C] (front).
1.
Fusing unit (
)
2.
Fusing entrance guide plate [A].
542
• The screws [B] are threaded screws. When you assemble the unit, take care not to use the wrong screws.
Fusing Unit
• Fasten the screw in the marked screw hole [C].
Carefully remove adhering toner as shown in the diagram below with a dry cloth. Then, wipe with a cloth moistened with alcohol.
1.
Fusing unit (
)
2.
Fusing upper cover (
)
3.
Fusing exit guide plate [A]
Remove the clip ring, and then slide this part to the right to remove it.
543
4. Replacement and Adjustment
1.
Open the fusing exit guide plate [A].
2.
Wipe clean with a dry cloth. Then wipe clean with a cloth dampened with alcohol.
544
1.
Fusing unit (
)
2.
Fusing upper cover [A]
1.
Fusing unit (
)
2.
Remove 4 screws on the front and rear sides.
Fusing Unit
545
4. Replacement and Adjustment
3.
Lift the fusing unit to remove the fusing lower cover [A].
546
• The fusing sleeve belt unit is designed with a highly soft material. Do not touch the sleeve belt unit with your hands to prevent dents during replacement. If you have touched it and a dent has been made, the dent will gradually become larger during operation and it can cause a fusing malfunction or sleeve belt breakage.
• To cancel SC544-02/SC554-02, it is necessary to replace the fusing unit or install an intact new
unit detection fuse. Refer to page 973 "When SC544-02, SC554-02 (Non-contact Thermistor
High Temperature Detection) Is Displayed".
• If you are replacing the fusing sleeve belt unit for PM or any reason other than canceling
SC544-02/SC554-02, you can discard the fuse that is packed with the new fusing sleeve belt unit.
Fusing Unit
Before replacing the fusing sleeve belt unit, set SP3-701-116 to "1" and switch the power OFF. Then replace the fusing sleeve belt unit and switch the power ON.
SP3-701 (Manual New Unit Set)
This SP is the new unit detection flag.
0: new unit detection flag OFF, 1: new unit detection flag ON
Fusing sleeve belt unit
Item
SP3-701-116
SP
1.
Fusing upper cover (
)
2.
Fusing lower cover (
)
3.
Left frame [A]
4.
Exit guide plate (left) unit [A]
547
548
4. Replacement and Adjustment
5.
Fusing exit driven roller [A]
6.
Side plate [A]
Fusing Unit
7.
Two screws.
8.
Release the boss caps on both sides, and then detach the fusing sleeve belt unit [A].
549
4. Replacement and Adjustment
9.
Remove the spring, and then remove the separation plate [A] and supports [B].
550
Before replacing the Pressure Roller, set SP3-701-118 to "1" and switch the power OFF. Then replace the pressure roller and switch the power ON.
SP3-701 (Manual New Unit Set)
This SP is the new unit detection flag.
0: new unit detection flag OFF, 1: new unit detection flag ON
Item SP
Pressure Roller SP3-701-118
• Do not remove or adjust the pressure adjusting screws [A] when replacing the pressure roller.
• The fusing unit is adjusted in the factory to match the hardness of the pressure roller, so that the nip width will be correct.
• Do not move the pressure roller to another fusing unit.
1.
Fusing sleeve belt unit (
)
2.
Pressure roller [A]
Fusing Unit
551
4. Replacement and Adjustment
3.
Apply the grease (FLUOTRIBO MG GREASE) to the rear shaft of the pressure roller at
5-7mm from the cut edge.
4.
Apply the grease (FLUOTRIBO MG GREASE) to the front shaft of the pressure roller at
5-7mm from the C-ring notch.
552
1.
Fusing upper cover (
)
2.
Fusing lower cover (
)
3.
Left frame [A]
4.
Fusing sleeve thermostat unit [A]
1.
Fusing upper cover (
)
2.
Fusing lower cover (
)
3.
Left frame [A]
Fusing Unit
553
4. Replacement and Adjustment
4.
Non-contact thermistor unit [A]
1.
Fusing entrance guide plate ( page 542 )
2.
Fusing upper cover (
)
3.
Fusing lower cover (
)
4.
Pressure roller thermistor [A].
554
1.
Fusing unit (
)
2.
Thermopile unit [A]
1.
Fusing unit (
)
2.
Pressure roller HP sensor unit [A]
Fusing Unit
555
556
4. Replacement and Adjustment
3.
Pressure roller HP sensor [A]
1.
Paper exit unit (
)
2.
Fusing exit drive solenoid [A].
1.
Fusing unit (
)
2.
Inner cover [A]
3.
Paper exit unit [A]
1.
Paper exit unit (
)
Paper Exit
557
558
4. Replacement and Adjustment
2.
Paper exit solenoid [A]
1.
Paper exit unit (
)
2.
Feeler [A]
3.
Harness [A]
4.
Paper exit sensor unit [A]
5.
Paper exit sensor [A]
Paper Exit
559
560
4. Replacement and Adjustment
1.
Paper exit unit (
)
2.
Reverse sensor unit [A]
When attaching the reverse sensor, if you screw too tightly in the direction of the blue arrow, it may cause the gap between the guide plates [A] to be too narrow, resulting in paper jams. Make sure that there is a gap [A] of 3mm or more after you fasten the screw.
3.
Reverse sensor [A]
1.
Paper exit unit (
)
2.
Gear [A] (Tab x1)
Paper Exit
561
4. Replacement and Adjustment
3.
Reverse motor unit [A]
4.
Reverse motor [A]
562
1.
Paper exit unit (
)
2.
Fusing exit sensor unit [A]
3.
Fusing exit sensor [A]
Paper Exit
563
4. Replacement and Adjustment
• The 1st paper feed unit can be removed without removing the duplex unit (just open the right door), and you can remove the paper feed unit after pulling out the paper tray.
• The 1st paper feed unit and 2nd paper feed unit are not interchangeable.
1.
Open the right door.
2.
Arms [A] [B]
564
3.
Open the right door wide.
4.
Pull out the 1st paper tray [A].
5.
Press the left tab to release the lock, and remove the paper feed guide plate [A].
Paper Feed
6.
1st paper feed unit [A]
565
566
4. Replacement and Adjustment
1.
2.
Pull out the 2nd paper tray [A].
3.
Transport guide [A]
4.
Harness guide [A] (Hook x 1)
5.
Press the left tab to release the lock, and remove the paper feed guide plate [A].
6.
2nd paper feed unit [A]
Paper Feed
567
4. Replacement and Adjustment
1.
Open the right door.
2.
Arms [A] [B]
3.
Open the right door wide.
4.
Paper dust collection unit [A]
568
1.
2.
Retainer [A]
3.
Pick-up Roller [A]
Paper Feed
569
570
4. Replacement and Adjustment
4.
Paper Feed Roller [A]
5.
Separation Roller [A]
6.
Torque Limiter [A]
1.
HVP-CB with bracket ( page 622 )
2.
1st Tray Lift Motor [A]
Paper Feed
571
572
4. Replacement and Adjustment
3.
2nd Tray Lift Motor [A]
1.
2.
Transport sensor unit [A]
3.
Transport sensor [A]
1.
2.
Upper limit sensor [A]
1.
Paper Feed
573
4. Replacement and Adjustment
2.
While pressing the tab enclosed by the blue circle, remove the paper end sensor [A]
(Harness×1).
574
1.
Open the right door.
2.
Paper transfer roller unit ( page 495 )
3.
Inner bracket [A]
4.
Remove two screws, then release the tab by inserting a flathead driver behind the registration sensor [A].
Paper Feed
575
576
4. Replacement and Adjustment
1.
Open the right door.
2.
Arm [A][B]
3.
Open the right door wide.
4.
Paper transport guide [A]
Bypass Tray Unit
5.
Harness
577
4. Replacement and Adjustment
6.
Release the tab and loosen the harness bracket [A].
7.
Bypass tray [A]
578
• When attaching the bypass tray, pass the harness through the indicated position as shown.
1.
Open the bypass tray [A].
Bypass Tray Unit
579
580
4. Replacement and Adjustment
2.
Bypass paper end sensor cover [A]
3.
Bypass paper end sensor unit [A]
4.
Bypass paper end sensor [A]
1.
Open the bypass tray.
2.
Bypass pick-up roller [A]
1.
Bypass paper end sensor unit ( page 579 )
2.
Bypass paper feed roller [A]
Bypass Tray Unit
1.
Open the right door.
581
582
4. Replacement and Adjustment
2.
Arm [A][B]
3.
Open the right door wide.
4.
Paper transport guide [A]
5.
Bypass separation roller [A]
6.
Torque limiter [A]
1.
Bypass Tray Unit
583
4. Replacement and Adjustment
2.
Six screws on the bypass tray [A] ( ×6).
584
3.
Release the hooks around the bypass tray [A].
• There is a hook in the tray cover. Be careful not to damage it during removal or installation.
4.
Release the links.
Bypass Tray Unit
585
4. Replacement and Adjustment
5.
Bypass tray upper cover [A] (pin x 1, x1)
6.
Bypass width sensor [A] ( ×1, hook x2)
586
• When installing, the holes must align as shown below.
1.
2.
Six screws on the bypass tray [A] ( ×6).
Bypass Tray Unit
587
588
4. Replacement and Adjustment
3.
Release the hooks around the bypass tray [A].
• There is a hook in the tray cover. Be careful not to damage it during removal or installation.
4.
Release the links.
5.
Bypass tray upper cover [A] (pin x 1, x1)
Bypass Tray Unit
589
590
4. Replacement and Adjustment
6.
Bypass length sensor [A] ( ×1, hooks)
1.
Unlock the lever [A], and then open the right door [B].
Duplex Unit
2.
Arms [A] [B]
3.
591
4. Replacement and Adjustment
4.
Main power switch cover (
)
5.
Duplex unit [A]
592
1.
2.
Harness guide [A]
Duplex Unit
3.
Duplex/Bypass motor unit [A]
4.
Duplex/Bypass Motor [A]
1.
Remove two tabs, and remove the transport guide [A].
• Make sure to release the tab on the right [C] first.
• When you reattach this part, make sure to attach it from the tab on the left [B] first.
593
594
4. Replacement and Adjustment
2.
Duplex entrance unit [A]
3.
Duplex entrance sensor unit [A]
1.
2.
Harness guide [A]
Duplex Unit
595
596
4. Replacement and Adjustment
3.
Duplex exit sensor unit [A]
4.
Duplex exit sensor [A]
Electrical Components
• Before doing any work, touch a metal object to discharge static electricity from the body. There is a possibility that the electrical components may malfunction due to static electricity.
• When disconnecting the FFC, release the lock.
• [A]: Disconnect the scanner FFC for the IPU while pressing the lock release button.
• [B]: Disconnect the other FFC while pressing the lock release levers on its sides.
597
598
4. Replacement and Adjustment
[A]
[B]
[C]
[D]
[E]
IPU
BCU
Controller Box Cooling Fan
Controller Board
HDD
[A]
[B]
HVP_TTS
Imaging IOB
Electrical Components
[A]
[B]
[C]
PSU (AC controller board)
PSU (DC Power)
PSU Cooling Fan
[A]
[B]
HVP_CB
Paper Transport IOB
599
600
4. Replacement and Adjustment
1.
2.
Controller box cover [A].
Red circles: Remove / Blue circles: Loosen
• The FFC connector has a lock mechanism. Do not use force to pull it out.
1.
Controller box cover (
)
2.
IPU [A]
Disconnect the upper FFC (scanner) while pressing the lock release button.
Disconnect the lower FFC while pressing the lock release levers on its sides.
Electrical Components
• The FFC connector has a lock mechanism. Do not use force to pull it out.
1.
Controller box cover (
)
2.
BCU [A]
Disconnect the FFCs while pressing the lock release levers on its sides. Disconnecting the FFC without releasing the lock may cause the FFC or connector to be damaged, resulting in an SC670 error.
601
4. Replacement and Adjustment
Remove the NVRAM (EEPROM) [A] from the old BCU. Then install it on the new BCU after you replace the BCU.
602
Replace the NVRAM (page 602) if the NVRAM on the old BCU is defective.
• Make sure you print out the SMC reports ("SP Mode Data" and "Logging Data") before you replace the NVRAM (EEPROM).
• Keep NVRAMs (EEPROM) away from any objects that can cause static electricity. Static electricity can damage NVRAM data.
• Make sure the serial number is input in the machine for the NVRAM data with SP5-811-004, if not,
SC995-001 occurs
1.
Make sure that you have the SMC report (factory settings). This report comes with the machine.
2.
Output the SMC data ("ALL") using SP5-990-001/SP5-992-001.
Make sure to shut down and reboot the machine once before printing/exporting the SMC.
Otherwise, the latest settings may not be collected when the SMC is printed/exported.
3.
Turn OFF the main power switch.
4.
Insert a blank SD card in the SD slot #2, and then turn ON the main power switch.
5.
Use SP5-824-001 to upload the NVRAM data from the BCU.
6.
Turn off the main power switch and unplug the power cord.
7.
Replace the NVRAM on the BCU with a new one.
Electrical Components
8.
Plug in, and then turn on the main power switch.
• When the power is turned ON, SC195-00 appears, but continue with the following steps.
9.
Select the destination setting. (SP5-131-001) (JPN: 0, NA: 1, EU/AA/TWN/CHN: 2)
10.
Set the following SP, Machine Serial Set (SP5-811-001), Area Selection (SP5-807-001), and CPM Set (SP5-882-001).
• For information on how to configure this SP, contact the supervisor in your branch office.
11.
Turn off the machine, and then turn it back on.
12.
Use SP5-801-002 "Memory Clear Engine".
• After changing the EEPROM, Some SPs do not have appropriate initial values. Because of this, steps 10 to 12 are done.
13.
Turn off the machine, and then turn it back on.
14.
From the SD card where you saved the NV-RAM data in step 5, download the NV-RAM data (SP5-825-001).
15.
Turn off the machine, and then remove the SD card from slot #2.
16.
Turn on the main power switch.
17.
Check the factory setting sheet and the SMC data printout from step 2, and set the user tool and SP settings so they are the same as before.
18.
Do ACC (Copier function and Printer function).
SP descriptions
• SP5-811-004 (MachineSerial Set)
Displays/Enters serial number of BCU EEPROM.
• SP5-131-001 (Paper Size Type Selection)
Sets the region setting for paper size/type.
(0: Japan, 1: NA, 2: EU/AA/TWN/CHN)
• SP5-811-001 (MachineSerial)
Displays machine serial number.
• SP5-807-001 (Area Selection)
Sets the machine destination.
(1: Japan, 2: NA, 3: EU, 4: Taiwan, 5: Asia, 6: China, 7: Korea)
• SP5-801-002 (Memory Clear: Engine)
Clears non-volatile memory of engine.
603
604
4. Replacement and Adjustment
• SP5-824-001 (NV-RAM Data Upload)
Uploads the NVRAM data to an SD card.
• SP5-825-001 (NV-RAM Data Download)
Downloads data from an SD card to the NVRAM in the machine.
• Keep NVRAMs away from any objects that can cause static electricity. Static electricity can damage NVRAM data.
1.
Controller cover (
)
2.
Controller box cover (
)
3.
Controller bracket [A]
Electrical Components
4.
Controller Board [A]
5.
DIMM [A]
6.
Remove the two used NVRAMs from the old controller board and install them on the new controller board.
• Make sure that the FRAM1 and FRAM2 are placed at the right position and orientation when attaching to the new board.
• Incorrect installation of the NVRAM will damage both the controller board and NVRAM.
605
4. Replacement and Adjustment
606
[A]
Position Label on the board
Left FRAM1
Label on the NVRAM
2M-1
[B] Right FRAM2 2M-2
• When replacing the controller board, first, check which SDK applications have been installed. After replacing the controller board, re-install the SDK applications by following the installation instructions for each application.
• After reinstalling the SDK applications, print the SMC (SP-5-990-024/025 (SMC: SDK/
Application Info)). Then open the front upper cover. Store the SMC sheet and the SD card(s) that was used to install the SDK application(s).
• Referring to the following procedure, be sure that there are no mistakes in the mounting position and orientation of the NVRAMs.
Incorrect installation of the NVRAM will damage both the controller board and NVRAM.
• SC195 (Machine serial number error) will be displayed if you forget to attach the NVRAM.
• Passwords for the Supervisor and Administrator 1 will be discarded later in this procedure.
• Installing a new NVRAM initializes SPs and issues an SC. Reset the SC with the procedure below.
Mounting position and orientation of the NVRAMs
Electrical Components
[A]
[B]
Position Label on the board
Left
Right
FRAM1
FRAM2
Label on the NVRAM
2M-1
2M-2
1.
Make sure that you have the SMC report (factory settings). This report comes with the machine.
2.
Output all the SMC data using SP5-990-001 (SP Print Mode: All (Data List)), or download the SMC data to an SD card using SP5-992-001 (SP Text mode: ALL (Data List))
Make sure to shut down and reboot the machine once before printing/exporting the SMC.
Otherwise, the latest settings may not be collected when the SMC is printed/exported.
3.
Turn the main power switch OFF.
4.
Insert an SD card into Slot 2 and turn the main power switch ON.
5.
Upload the NV-RAM data on the controller board to the SD card using SP5-824-001 (NV-
RAM Data Upload).
607
608
4. Replacement and Adjustment
6.
Make sure that the customer has backed up their Address Book data. If they have not, save the Address Book data to an SD card using SP5-846-051 (Backup All Addr Book).
• The address data stored in the machine will be discarded later during this procedure. So be sure to obtain a backup of the customer’s address book data.
• Note that the counters for the user will be reset when doing the backup/restore of the address book data.
• If they have a backup of the address book data, use their own backup data for restoring. This is because there is a risk that the data cannot be backed up properly depending on the NV-
RAM condition.
7.
Do the following steps if the machine has the fax unit. If not, skip this step:
1. Print the Box List with the User Tools/Counter.
• [User Tools/Counter] - [Facsimile Features] - [General Settings] - [Box Setting: Print List]
2. Print the Special Sender List by pressing these buttons in the following order.
• [User Tools/Counter] - [Facsimile Features] - [Reception Settings] - [Program Special
Sender: Print List]
3. Write down the following fax settings.
• [Receiver] in [User Tools/Counter] - [Facsimile Features] - [Reception Settings] -
[Reception File Settings] - [Forwarding].
• [Notify Destination] in [User Tools/Counter] - [Facsimile Features] - [Reception Settings] -
[Reception File Settings] - [Store].
• [Specify User] in [User Tools/Counter] - [Facsimile Features] - [Reception Settings] -
[Stored Reception File User Setting].
• [Notify Destination] in [User Tools/Counter] - [Facsimile Features] - [Reception Settings] -
[Folder Transfer Result Report].
• Specified folder in [User Tools/Counter] - [Facsimile Features] - [Send Settings] -
[Backup File TX Setting].
• [Receiver] in [User Tools/Counter] - [Facsimile Features] - [Reception Settings] -
[Reception File Settings] - [Output Mode Switch Timer].
• [Store: Notify Destination] in [User Tools/Counter] - [Facsimile Features] - [Reception
Settings] - [Output Mode Switch Timer].
• All the destination information shown on the display.
• In the fax settings, address book data is stored with entry IDs, which the system internally assigns to each data. The entry IDs may be changed due to re-assigning in backup/ restore operations.
Electrical Components
4. Make sure that there is no transmission standby file. If any standby file exists, ask the customer to delete it or complete the transmission.
8.
Turn the power OFF and unplug the power supply cord.
9.
Push the power switch ON again to discharge the residual charge.
10.
Replace the NV-RAM with a brand-new one.
11.
Turn the power ON with the SD card to which the NV-RAM data has been uploaded in
Slot 2.
• SC673 appears at start-up, but this is normal behavior. This is because the controller and the smart operation panel cannot communicate with each other due to changing the SP settings for the operation panel.
12.
Change the SP settings for the operation panel.
If you switch the screen to enter the SP mode, SC995-02 is displayed. However, continue the following steps.
• SP5-748-101: (OpePanel Setting: Op Type Action Setting): Change bit 0 from 0 to 1.
• SP5-748-201: (OpePanel Setting: Cheetah Panel Connect Setting): Change the value from 0 to 1.
13.
Change the Flair API SP values.
• SP5-752-001 (Copy FlairAPIFunction Setting): Change bit 0 from 0 to 1.
• SP1-041-001 (Scan:FlairAPI Setting): Change bit 0 from 0 to 1.
• SP3-301-001 (FAX:FlairAPI Setting) Change bit 0 from 0 to 1.
14.
Cycle the power OFF/ON.
• The model information is written on the NVRAM (Novita), so SC995-02 does not occur.
• Program/Change Administrator will be displayed in Japanese, but this is normal.
15.
Enter the SP mode and specify the following settings manually.
• a. SP5-985-001 (Device Setting: On Board NIC) Change the value from 0 to 1.
• b. SP5-985-002 (Device Setting: On Board USB) Change the value from 0 to 1.
16.
Turn OFF the main power, and then turn ON the main power with the SD card to which the NV-RAM data has been uploaded in Slot 2.
17.
Download the NV-RAM data stored in the SD card to the brand-new NV-RAM using
SP5-825-001 (NV-RAM Data Download).
• The download will take a couple of minutes.
18.
Turn the power OFF and remove the SD card from slot 2.
609
610
4. Replacement and Adjustment
19.
Turn the power ON.
The screen "Program/Change Administrator" will be displayed in the language that is the same language as the time when the data was uploaded to the SD card in step 5.
20.
Execute SP5-755-002 (Hide Administrator Password Change Scrn).
After you execute this SP and exit SP mode, the Home screen is displayed and user functions can be used.
21.
Check that the fax and scanner icons are displayed, and then change the following SP settings.
a. SP5-193-001 (External Controller Info. Settings) Change the value from 0 to 1.
b. SP5-895-001 (Application invalidation: Printer) Change the value from 0 to 1.
c. SP5-895-002 (Application invalidation: Scanner) Change the value from 0 to 1.
22.
If the security functions (e.g. Stored file encryption/ Auto Erase Memory Setting) were applied, set the functions again.
23.
Ask the customer to restore their address book. Or restore the address book data using
SP5-846-052 (UCS Setting: Restore All Addr Book), and ask the customer to ensure the address book data has been restored properly.
• If you obtained the backup of the customer’s address book data in step 3, delete the backup immediately after the NV-RAM replacement to avoid accidentally taking out the customer’s data.
24.
Output all the SMC data with SP5-990-001 and make sure all the SP/UP settings except for counter information are properly restored, by checking the SMC data obtained in step
2.
• The counters will be reset.
25.
When equipped with fax, make sure that the list printed in steps 7-1 to 7-2 are the same as the sender information that you wrote down in step 7-3.
If the setting is different from the original setting after the replacement of the NVRAM, then set it again to the original setting.
26.
Execute the process control (SP3-011-001).
27.
Execute the ACC (Copy).
28.
Execute the ACC (Printer).
29.
Cycle the power OFF/ON.
• If you cannot execute SP5-824-001 or SP5-825-001 for some reason, try all the following things.
Electrical Components
- Check the changed SP value on the SMC which was output in step 2 and set it manually.
Especially, ensure that the values of the following SPs are same as the setting before the replacement.
- a. SP5-045-001 (Accounting counter: Counter Method)
- b. SP5-302-002 (Set Time: Time Difference)
• Because the PM counters have been reset during NV-RAM replacement, it is necessary to replace all the PM parts for proper PM management.
• If a message tells you need a SD card to restore displays after the NV-RAM replacement, create a
"SD card for restoration" and restore with the SD card.
SP descriptions
• 5-846-051 (UCS Setting: Backup All Addr Book)
Uploads all directory information to the SD card.
• SP5-748-101 (OpePanel Setting: Op Type Action Setting)
Sets the operation panel type.
0: Normal operation panel
1: Smart operation panel
• SP5-748-201 (OpePanel Setting: Cheetah Panel Connect Setting)
0: OFF
1: ON
• SP5-752-001 (Copy: FlairAPIFunction Setting)
Sets Copy FlairAPI Function enable / disable.
• SP1-041-001 (Scan: FlairAPI Setting)
Sets Scanner FlairAPI Function enable / disable.
• SP3-301-001 (FAX: FlairAPI Setting)
Sets Fax FlairAPI Function enable / disable.
Bit Switches for FlairAPI Settings
Bit Item 0 1 Description
Initial value
0
Flair API
Server Boot
Disabled Enabled
Specifies whether to start the HTTP server for Flair API.
"0" disables all the Flair API functions
(Remote UI).
0
611
4. Replacement and Adjustment
612
Bit Item 0 1 Description
Initial value
1
2
Access
Permission
Select IPv6/
IPv4
Enabled
IPv6
Disabled
IPv4
Setting this value to “0” permits only internal access in the machine (MFP browser).
Setting this value to “1” permits to access from external devices such as
PC, Remote UI, IT-BOX.
Setting this value to “0” permits only accessing with IPv6.
Setting this value to “1” permits accessing with IPv4 or IPv6.
Sets whether to use the Remote UI.
0
0
3
4
5
Remote UI
Reserved
Reserved
-
-
Not use
-
-
Use
N/A
N/A
0
N/A
N/A
6
7
Reserved
Reserved
-
-
-
-
N/A
N/A
N/A
N/A
• SP5-985-001/002 (Device Setting: On Board NIC/On Board USB)
The NIC and USB support features are built into the GW controller. Use this SP to enable and disable these features. In order to use the NIC and USB functions built into the controller board, these SP codes must be set to "1".
• SP5-824-001 (NV-RAM Data Upload)
Uploads the NVRAM data to an SD card.
• SP5-825-001 (NV-RAM Data Download)
Downloads data from an SD card to the NVRAM in the machine.
• SP5-755-002 (Hide Administrator Password Change Scrn)
Hides the input screen of the administrator password temporarily.
• SP5-193-001 (External Controller Info. Settings)
Sets the model of the external controller connected to the main unit.
0: External Controller is not installed
1: EFI
2: Ratio
3: Egret
Electrical Components
4: GJ
5: Creo
6: QX-100
7: Kurofune
8 to 10: Reserved
• SP5-846-052 (UCS Setting: Restore All Addr Book)
Downloads all directory information from the SD card.
• SP3-011-001 (Manual ProCon :Exe: Normal ProCon)
Executes Process control.
• SP5-045-001 (Accounting counter: Counter Method)
Sets the counter methods as follows; Developments, Prints or Coverage.
• SP5-302-002 (Set Time: Time Difference)
Adjusts the RTC (real time clock) time setting for the local time zone.
Examples: For Japan (+9 GMT), enter 540 (9 hours x 60 min.)
Japan: +540 (Tokyo)
NA: -300 (New York)
EU: + 60 (Paris)
CHN: +480 (Beijing)
TWN: +480 (Taipei)
AA: +480 (Hong Kong)
KO: +540 (Korea)
• Before replacing the HDD, copy the address book data to an SD card with SP5846-051 if possible.
• If the customer is using the Data Overwrite Security, the Data Encryption feature or OCR Scanned
PDF, these applications must be installed again.
1.
Controller box cover (
)
613
4. Replacement and Adjustment
2.
HDD [A]
614
1.
Run SP5-832-001, to initialize the hard disk.
Even if you use an HDD that is already formatted, it is recommended that you re-initialize.
2.
Run SP5-853-001, to install the fixed stamps.
3.
Run SP5-846-052, to copy the address book from the SD card to the HDD.
4.
Turn off the machine, and then turn it back on.
SP descriptions
• SP5-832-001 (HDD Formatting: HDD Formatting (ALL))
Initializes the hard disk.
• SP5-853-001 (Stamp Date Download)
Downloads the fixed stamp data from the machine ROM onto the hard disk. Then these stamps can be used by the User Tools menu. If this is not done, the user will not have access to the fixed stamps
("Confidential", "Secret", etc.).
You must always execute this SP after replacing the HDD or after formatting the HDD.
• SP5-846-052 (UCS Setting: Restore All Addr Book)
Downloads all directory information from the SD card.
1.
Controller cover (
)
2.
Controller box cover (
)
3.
Bracket [A]
4.
Controller box [A]
Electrical Components
1.
Controller cover (
)
2.
Controller box cover (
)
615
4. Replacement and Adjustment
3.
Disconnect the FFC [A] between IPU-Scanner Unit while pressing the lock release button.
4.
Open the controller box [A].
616
5.
Imaging IOB [A]
Disconnect the FFC while pressing the lock release levers on its sides. Disconnecting the FFC without releasing the lock may cause the FFC or connector to be damaged, resulting in an SC670 error.
Electrical Components
1.
Controller cover (
)
2.
Controller box cover( page 600 )
3.
Disconnect the FFC [A] between IPU-Scanner Unit while pressing the lock release button.
617
4. Replacement and Adjustment
4.
Open the controller box [A].
5.
HVP_TTS [A]
618
• Turn off the main power switch and unplug the power cord before replacing the PSU.
• Do not touch the areas outlined in red in the following diagrams when replacing the PSU. Residual charge on the board may cause electric shock.
Electrical Components
1.
Rear lower cover (
)
2.
PSU (AC Controller Board) [A]
• Turn OFF the main power switch and unplug the power cord before replacing the PSU.
619
4. Replacement and Adjustment
• Do not touch the areas outlined in red in the following diagrams when replacing the PSU. Residual charge on the board may cause electric shock.
100V 200V
1.
Rear lower cover (
)
2.
PSU (DC Power) [A]
620
1.
Rear lower cover (
)
2.
Power supply box [A] ( x6, Among them, tapping screw x1)
Electrical Components
• You can hang the power box [A] on the machine by using 3 tabs.
1.
Power supply box (
)
621
4. Replacement and Adjustment
2.
Paper transport IOB [A]
1.
Power supply box (
)
2.
HVP_CB [A]
622
1.
Power supply box (
)
2.
Release the 5 clamps.
3.
Remove the HVP-CB with bracket [A] (Tab x2)
Electrical Components
623
624
4. Replacement and Adjustment
1.
Front upper cover (
)
2.
Proximity sensor (Human detection sensor) board [A].
Fans/Filters
Before replacing the Dust filter, set SP3-701-132 to "1" and switch the power OFF. Then replace the
Dust filter and switch the power ON.
1.
Pull out the ozone filter and dust filter box [A].
2.
Ozone filter [A], Dust filter [B]
625
626
4. Replacement and Adjustment
• When attaching the ozone filter and dust filter unit to the machine, attach it by pressing the area below its center [A]. Attaching it by pressing the area above the center may cause incomplete attachment.
1.
Deodorization filter box [A]
2.
Deodorization filter [A]
1.
Inner lower cover (
)
2.
Development intake fan unit [A]
Fans/Filters
627
4. Replacement and Adjustment
3.
Development intake fan [A]
1.
Power supply box (
)
2.
Ozone exhaust fan [A]
628
1.
Front upper cover (
)
2.
Paper exit cooling fan [A]
1.
2.
3.
Fusing exhaust fan unit [A]
Fans/Filters
629
630
4. Replacement and Adjustment
4.
Fusing exhaust fan [A]
1.
2.
3.
Toner supply cooling fan unit [A]
4.
Toner supply cooling fan [A]
1.
Rear lower cover (
)
2.
PSU cooling fan unit [A]
3.
PSU cooling fan [A]
Fans/Filters
631
632
4. Replacement and Adjustment
1.
Controller box cover (
)
2.
Controller box cooling fan [A]
Image Adjustment
For the best image quality, this is done during installation, and should be done periodically by the customer. It is accessed with the user tools as follows.
User Tools -> Machine Features -> Maintenance -> Auto Color Calibration
• When you set the adjustment sheet on the exposure glass, put about 10 pieces of white paper on the adjustment sheet in order for the original to contact the exposure glass sufficiently. Instruct the customer to periodically execute the ACC.
Description
[A] Output adjustment sheets. You must execute both for copy and printer functions.
[B] Roll back to the previous value.
[C] Displays the last date/time ACC was executed.
About the printer ACC
It is difficult to keep constant printing density due to the environment of the machine, individual differences between devices, and the passage of time. The printer ACC reads the current printing density using the scanner, and then compares the result with the time when it was in a normal state, and makes the printing density close to the normal state.
633
4. Replacement and Adjustment
Issues possibly solved by the printer ACC
• When the printed image looks strongly red, blue, or yellow because the density of the cyan, magenta, and yellow are not balanced.
• When the printed image looks too dark or light.
634
Issues cannot be solved by the printer ACC
The tone differences from other types of machine or machines of other manufactures cannot be solved by the printer ACC. The tone differences from the machines of other manufactures occur due to the differences in color reproduction caused by the difference in the engine and color profile specifications so it may not be solved even after performing the printer ACC.
Refer to page 648 "Adjustment by Changing the Machine’s Profile Setting" for the color tone
differences from the other types of the machine.
Check the printing registration/side-to-side adjustment and the blank margin adjustment before you do the following scanner adjustments.
• Use a C4 test chart to do the following adjustments.
Image Adjustment
A: Sub-scan magnification
1. Put the test chart on the exposure glass. Then make a copy from one of the feed stations.
2. Check the magnification ratio. Adjust with SP4-008 if necessary.
Standard: ±1.0%.
A: Leading Edge Registration
1. Put the test chart on the exposure glass. Then make a copy from one of the feed stations.
2. Check the leading edge and side-to-side registration. Adjust the following SP modes if necessary.
Standard: 0 ± 2mm for the leading edge registration, 0 ± 2.5mm for the side-to-side registration.
635
4. Replacement and Adjustment
What It Does
Leading edge registration (Home Position Adj Value)
Side-to-Side Registration (Main Scan Reg)
SP code
SP4-803-001
SP4-011-001
636
A: Leading edge registration
Use A3/DLT paper to make a temporary test chart as shown above.
1. Put the temporary test chart on the ARDF. Then make a copy from one of the feed stations.
2. Check the registration. Check the leading edge and side-to-side registration. Adjust the following
SP modes if necessary.
Standard: 4.2 ± 2 mm for the leading edge registration, 2 ± 1 mm for the side-to-side registration.
Use the following SP modes to adjust if necessary.
SP Code
SP6-006-001
SP6-006-003
SP6-006-005
SP6-006-006
SP6-006-007
What It Does
Side-to-Side Regist: Front
Leading Edge Registration
Buckle: Duplex Front
Buckle: Duplex Rear
Rear Edge Erase (Trailing Edge)
Adjustment Range
± 3.0 mm
± 5.0 mm
± 3.0 mm
± 2.5 mm
± 10.0 mm
Image Adjustment
1. Put the temporary test chart on the ARDF. Then make a copy from one of the feed stations.
2. Check the magnification ratio. Adjust with SP6-017-001 if necessary.
• Standard: ±5.0%
• Reduction mode: ±1.0%
• Enlargement mode: ±1.0%
A = C = 5.2 mm (0.2"), B = 2.0 mm
Make sure that the registration is adjusted within the adjustment standard range as shown below.
Adjusts the leading edge registration for each paper type and process line speed.
Adjusts the side-to-side registration for each paper feed station. Use SP mode (SP1-002) to adjust the side-to-side registration for the optional paper feed unit, LCT, and duplex unit.
637
638
4. Replacement and Adjustment
• Leading edge (sub-scan direction): 5.2 ± 2 mm
• Side to side (main-scan direction): 2 ± 1 mm
The registration in both main- and sub-scan directions can change within the following tolerance.
• Sub-scan direction: 0 ± 9 mm
• Main-scan direction: 0 ± 4 mm
1. Enter SP2-109-003.
2. Print out the test pattern (14: Trimmed area) with SP2-109-003.
• Registration can change slightly as shown on the previous page. Print some pages of the "14:
Trimmed area" for step 3 and 4. Then average the leading edge and side-to-side registration values, and adjust each SP mode.
3. Do the leading edge registration adjustment.
1) Check the leading edge registration and adjust it with SP1-001.
2) Select the adjustment conditions (paper type and process line speed).
3) Input the value. Then press the key.
4) Generate a trim pattern to check the leading edge adjustment.
4. Do the side-to-side registration adjustment.
1) Check the side-to-side registration and adjust it with SP1-002.
2) Select the adjustment conditions (paper feed station).
3) Input the value. Then press the key.
4) Generate a trim pattern to check the leading edge adjustment.
• Adjust the erase margin C and D only if the registration (main scan and sub scan) cannot be adjusted within the standard values. Do the registration adjustment after adjusting the erase margin
C and D, and then adjust the erase margin A and B.
Image Adjustment
1. Enter SP2-109-003.
2. Print out the test pattern (14: Trimmed area) with SP2-109-003.
3. Check the erase margin A and B. Adjust them with SP2-103-001 to -015 if necessary.
• Leading edge: 0.0 to 9.0 mm (default: 4.2 mm)
• Side-to-side: 0.0 to 9.0 mm (default: 2.0 mm)
• Trailing edge: 0.0 to 9.0 mm (default: 4.2 mm)
If a customer wishes to have the tone of the printed image corrected, you can adjust it as follows.
For details about the adjustment procedures, see the corresponding sections.
Adjustment Method
Adjustment by Changing the Printer
Adjustment by Changing the Machine’s
Outline
Perform this to adjust the tone for each print job. This can be adjusted by the user.
Perform this to make the tone similar to that of another model. Doing this changes the tone of all images printed by the machine’s printer function.
639
4. Replacement and Adjustment
Adjustment Method
Adjustment by Printer Gamma
Outline
Basically, we recommend the default setting. Doing this changes the tone of all images printed by the machine’s printer function.
Using the printer driver, you can change the color balance for each print job as follows.
1.
Open the printer driver’s "Color Balance Details" window. ( page 640 )
2.
Adjust the tone (color gamut). (
)
PCL6 driver / PS driver
1. Click [Detailed Setting] tab -> [Print Quality].
2. Click [Details...] in "Color Balance".
640
3. "Color Balance Details" window appears. (page 643)
PCL6 Universal driver / PS Universal driver
1. Click [Detailed Setting] tab -> [Print Quality:Advanced].
2. Click [Details...] in "Color Balance".
Image Adjustment
3. "Color Balance Details" window appears. (page 643)
Mac PS driver
1. On the print dialog box, open the context menu (right click menu), then select [Color Balance
Details].
641
642
4. Replacement and Adjustment
2. "Color Balance Details" window appears. (page 643)
PCL driver
Image Adjustment
PS driver
643
4. Replacement and Adjustment
Mac PS driver
Brightness
• Decreasing the brightness makes the printed image darker and increasing it makes the printed image fainter.
• Decrease the value to make the printed image darker and increase it to make the printed image fainter.
• If you increase the value too much, overexposure of bright areas may occur.
• If you decrease the value too much, underexposure of dark areas may occur
• Can be specified using the PCL/PS drivers.
644
Contrast
• Increasing the contrast makes bright areas brighter and dark areas darker.
• Decreasing the contrast makes bright areas darker and dark areas brighter.
Image Adjustment
• Increase the value to make the printed image clearer and decrease it to prevent overexposure of bright areas and underexposure of dark areas.
• If you increase the value too much, overexposure of bright areas and underexposure of dark areas may occur.
• If you decrease the value too much, the printed image may become unclear.
• Can be specified using the PCL/PS drivers.
Saturation
• Increasing the saturation makes the printed image more vivid.
• Decreasing the saturation makes the printed image closer to the neutral color (gray).
• If you increase the value too much, it may lower the gradation, resulting in a difficulty to distinguish colors.
• The printer’s color gamut is limited, so even if you increase the value, it may not make any difference.
• Can be specified using the PCL driver only.
RGB Adjustment (Adjust Each Color)
When using the PCL driver, adjust the tone (color gamut) by this method.
• Increasing "Red" makes "M" and "Y" more vivid and "C" less so.
• Decreasing "Red" makes "M" and "Y" less vivid and "C" more so.
• Increasing "Green" makes "C" and "Y" more vivid and "M" less so.
• Decreasing "Green" makes "C" and "Y" less vivid and "M" more so.
• Increasing "Blue" makes "C" and "M" more vivid and "Y" less so.
• Decreasing "Blue" makes "C" and "M" less vivid and "Y" more so.
645
4. Replacement and Adjustment
CMYK Adjustment (Adjust Each Color)
When using the PS driver, adjust the tone (color gamut) by this method.
646
The following shows adjustment examples. Be sure to check the printed image when changing values.
If the printed image is dark:
Increase the brightness by 20.
If the printed image is faint:
Decrease the brightness by 20.
If the printed image is too bluish:
Increase "Red" or "Magenta" by 20.
If the printed image is too reddish:
Increase "Blue" or "Cyan" by 20.
Image Adjustment
647
4. Replacement and Adjustment
If the printed image is unclear:
Increase the contrast by 15.
648
You can change the printer’s profile setting by specifying a bit switch in SP mode.
• By changing the profile setting, you can change the tone of all images printed by the machine’s printer function.
• By changing the profile setting, you can make the tone (image gamut) of the printed image similar to that of another model. However, due to factors such as the image gamut difference between different models, individual differences, and ageing of components, you may not achieve exactly the same tone.
1.
Enter the printer SP mode.
Image Adjustment
2.
Change the values of bit switches with the following SP numbers.
RTB 28
This table was modified
Desired tone (color gamut)
2009 Spring model or those before it
SP to change
2009 Autumn to 2011 Spring model
2011 Autumn model or later
Fuji Xerox product
SP1-001-002
SP1-001-001
Value to select
00000001
[01H]
00010000
[10H]
00000000
[00H]
10000000
[80H]
3.
Turn the machine’s power off and then back on.
The specified setting is applied.
Model with the desired tone
2009 Spring model or earlier
2009 Autumn to 2011
Spring model
2011 Autumn model or later
Fuji Xerox product
Image (Photo)
Color A
Color B
Color B
Color D
Graphic (Chart)
Color A
Color B
Color C
Color D
Text
Color A
Color B
Color C
Color D
Color A
Standard profile for MP C2030/C2050/C2030/C2530/C2800/C3300/C4000/C5000 and their preceding models
Color B
Standard profile for MP C2051/C2551/C3001/C3501/C4501/C5501.
Compared to Color A, following changes have been applied:
• Yellow tint of the skin color is reduced.
649
650
4. Replacement and Adjustment
• Redness is enhanced to prevent it from appearing like vermilion.
• Green and blue-green appear darker.
• Uses the pure cyan toner on graphics to prevent muddiness.
• Pink in the printed image appears darker.
Color C
Standard profile for MP C3002/C3502/C4502/C5502 up to the present model.
Compared to Color B, the difference between colors have become more recognizable. On the other hand, the printed image has become slightly less vivid.
If you receive a comment that the printed image is less vivid compared to that of a Color Bstandard model, we recommend changing the setting to Color B.
Color D
Profile with a tone similar to that of the prints by the FX products.
• Bluish colors appear slightly purplish. (Image of the sky appears with a slight tint of red.)
• Pink in the printed image appears with a tint of magenta.
• We recommend that you keep the printer gamma correction values at the default values.
• The values adjusted/saved in the printer SP mode are applied after the machine’s power is turned off and then back on.
• After adjusting/saving the values in the printer SP mode, make sure not to perform the printer’s
Auto Color Calibration (ACC). Doing so will reset the values.
• To change multiple resolutions, perform this procedure for each resolution.
1.
Select the mode you want to change in the printer SP1102-001: Resolution Setting.
1102 [Resolution Setting]
Selects the printing mode (resolution) for the printer gamma adjustment.
Image Adjustment
001 Resolution Setting CTL [0 to 9 / 0 / 1/step]
0: 1200x1200 Photo (2bit/4col)
1: 1200x1200 Photo (1bit/4col)
2: 600x600 Photo (4bit/4col)
3: 600x600 Photo (2bit/4col)
4: 600x600 Photo (1bit/4col)
5: 1200x1200 Text (2bit/4col)
6: 1200x1200 Text (1bit/4col)
7: 600x600 Text (4bit/4col)
8: 600x600 Text (2bit/4col)
9: 600x600 Text (1bit/4col)
2.
Change the gamma correction value for each color in the printer SP1104: Gamma
Adjustment.
• When adjusting the value, be sure to follow the sequence: I (IDmax) M (Middle) S
(Shadow) H (Highlight).
• To lower the print density, reduce and save the H/M/S/I value for each color.
• To heighten the print density, increase and save the H/M/S/I value for each color.
1104 [Gamma Adjustment]
Adjusts the printer gamma for the mode selected in the "Mode Selection" menu.
651
652
4. Replacement and Adjustment
001 Black: Highlight
002 Black: Shadow
003 Black: Middle
004 Black: IDmax
021 Cyan: Highlight
022 Cyan: Shadow
023 Cyan: Middle
024 Cyan: IDmax
041 Magenta: Highlight
042 Magenta: Shadow
043 Magenta: Middle
044 Magenta: IDmax
061 Yellow: Highlight
062 Yellow: Shadow
063 Yellow: Middle
064 Yellow: IDmax
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL [0 to 30 / 00 / 1/step ]
CTL
CTL
Image Adjustment
Gamma Correction Sheet
Range where each value affects
3.
Execute the SP1105-001: Save Tone Control Value.
• If you exit the SP mode without saving the values, any changes made in the printer SP1104:
Gamma Adjustment will be lost.
• You can check the color balance before and after the gamma adjustment in the printer
SP1103-001: Test Page - Color Gray Scale.
653
654
4. Replacement and Adjustment
4.
Turn the machine’s power off and then back on.
The changed gamma correction setting is applied.
5.
Check the output image and repeat steps 1 - 4 until the desired image is obtained.
Adjust color registration with the following procedure when color registration errors occurred.
Prepare some A3 sheets.
1.
Execute SP2-111-004 (Forced line Position Adj.: Mode d)
2.
Make sure that execution completed successfully with using SP2-194-007 (MUSIC).
If the value of SP2-194-007 is "0", it indicates that the result of SP2-111-004 was successful.
If the value of SP2-194-007 is "1", it indicates that the result of SP2-111-004 was a failure, which you need to fix the color registration errors (See "Ways to fix color registration errors"
3.
Execute SP2-109-003 (Test Pattern: Pattern Selection)
4.
With a loupe, check the details of the color registration errors on the printed test pattern.
• Specification: Main/Sub is smaller than 180.0um
• No color registration errors: Adjustment completed.
• Color registration errors occurred: Adjust the color registration errors (See "Ways to fix color
registration errors" (page 654)
In the following diagrams, solid lines represent "K" and dotted lines indicate any of "C", "M" or "Y".
1. Pattern 1
This is a case in which there is a shift in the sub-scan direction at the leading edge of the paper. The following diagram shows "C", "M" or "Y" lines closer to the leading edge than "K" lines.
Image Adjustment
2. Pattern 2
This is a case in which there is a shift in the sub-scan direction at the trailing edge of the paper. The following diagram shows "C", "M" or "Y" lines farther away from the leading edge than "K" lines.
3. Pattern 3
This is a case in which a color registration error is found in the main-scan direction and size of the error is the same at the left, center and right.
4. Pattern 4
This is a case in which a color registration error is found in the main-scan direction and the size of the error is different at the left, center and right. For "M", the largest error will be at the right,
655
4. Replacement and Adjustment followed by the center and then the left. For "C" or "Y", the order will be reversed. This is because the writing direction of the laser beam for "K" and "M" is different from "C" and "Y".
Case "M"
Case "C" or "Y"
656
5. Pattern 5
This is a case in which a color registration error is found in the sub-scan direction, but it is not the same as the Pattern 1 or 2. The error appears and disappears at intervals down the page.
Ways to fix color registration errors
SP2-111-004 (Forced Line Position Adj. : Mode D) Execution
Result: Failed Case: SP2-194-007: 1 (Failed)
Image Adjustment
SP2-194-010, 011,
012 shows "2" or "3"
Failed to read the pattern of Line position
Adj.
Causes
Solution
Pattern
Result of Check
Causes
Solution
Pattern
Result of Check
Blank image, abnormal image, low image density
1. Image processing failure
2. Pattern density low
3. BCU(IPU) failure
1.Replace PCU, image transfer belt, power pack
2. Execute process control, supply toner
3. Replace BCU(IPU)
-
Normal (but color registration errors occur)
-
1. ID sensor shutter failure
2. ID sensor failure
3. BCU(IPU) failure
1. Replace ID sensor shutter
2. Replace ID sensor
3. Replace BCU(IPU)
657
658
4. Replacement and Adjustment
Result of Check
Causes
Solution
Pattern
Any of SP2-194-010 or
011 or 012 shows "5"
Result of Check
Causes
Solution
Pattern
Image density low
-
Pattern density low
Execute the process control
Supply toner
Leading edge registration for "M", "C", and/or "Y" shifts over ±1.4 mm from that of "K".
1. Normal
2. Laser unit failure
3. BCU(IPU) failure
1. Execute SP2-111-003 (Forced Line Position Adj.:
Mode c)
2. Replace laser unit
3. Replace BCU(IPU)
3
Image Adjustment
Out of line position correction range
Result of Check
Causes
Solution
Pattern
Result of Check
Causes
Solution
Pattern
Leading edge registration of "M", "C", and/or "Y" shifts over ±1.4 mm from that of "K".
1. Normal
2. Image transfer belt failure
3. Drive section failure
4. BCU(IPU)failure
1. Execute SP2-111-003 (Forced Line Position Adj.:
Mode c)
2. Replace image transfer belt
3. Replace PCU/ PCU motor
4. Replace BCU(IPU)
1, 2
The main scan magnification is OK, but the color registration in the center of the image shifts over
0.66 mm.
-
1.ID Sensor(Center) failure
2. Significant movement of image transfer belt
(Center)
3.BCU(IPU) failure
1. Replace ID Sensor
2. Replace image transfer belt
3. Replace BCU(IPU)
659
660
4. Replacement and Adjustment
Out of line position correction range
Result of Check
Causes
Solution
Pattern
Result of Check
Causes
Solution
Skew of "M", "C", and/or "Y" shifts over ±0.75mm
against that of "K"
1. PCU installation failure
2. Laser Unit failure
3. BCU(IPU) failure
-
1. Reset/Replace PCU
2. Replace laser unit
3. Replace BCU(IPU)
Other
1. The upper skew correction value is abnormal
2. BCU(IPU) failure
-
1. Reset skew correction value (*1)
2. Replace BCU(IPU)
Pattern
*1 Method for resetting the skew correction value.
1. Turn the power OFF.
2. Remove the left cover (page 408)
3. Remove the harness of the laser optics positioning motor attached to the laser unit (15-pin).
Image Adjustment
4. Turn the power ON, and then execute the following SPs to set the skew correction mechanism to the origin.
SP2-220-001 (Skew Origin Set M: Skew Motor)
SP2-220-002 (Skew Origin Set C: Skew Motor)
SP2-220-003 (Skew Origin Set Y: Skew Motor)
5. Turn the power OFF.
6. Connect the harness of the laser optics positioning motor to the laser unit.
7. Turn the power ON
SP2-111-001 (Forced Line Position Adj.: Mode A) execution (or Color Registration via the
Maintenance menu in User Tools)
Result: OK Case: SP2-194-007: 0 (Success)
Result of Check
No color registration errors
Causes
Solution
Pattern -
Side-to-side registration for K shifted
Abnormal SP value of main scan color registration
(K)
Adjust SP2-101-001
Image density low
Color registration errors found
Result of Check
Causes
Solution
Pattern
Pattern density low
Execute process control, Supply toner
Result of Check
-
The main scan magnification of "M", "C" and/or
"Y" is not correct.
Color registration errors found
Causes
Solution
Pattern
1. Laser unit failure
2. ID sensor failure
3. BCU(IPU) failure
4. Normal
1. Replace laser unit
2. Replace ID sensor
3. Replace BCU(IPU)
4
661
662
4. Replacement and Adjustment
Color registration errors found
Color registration errors found
Result of Check
Causes
Solution
Pattern
Result of Check
Causes
Solution
Pattern
Although main scan magnification is OK, the color registration in the center of the image is shifted
1. Significant movement of image transfer belt
(Center)
2. ID sensor (Center) failure
3. BCU(IPU) failure
1. Replace image transfer belt
2. Replace ID sensor
3. Replace BCU(IPU)
-
The side-to-side registration of "M", "C", and/or "Y" is not correct.
1.ID sensor(Center) failure
2. Significant movement of Image transfer belt
(Center)
3.BCU(IPU) failure
1. Replace laser unit
2. Replace ID sensor
3. Replace BCU(IPU)
3
Image Adjustment
Color registration errors found
Color registration errors found
Color registration errors found
Result of Check
Causes
Solution
Pattern
Result of Check
Causes
Solution
Pattern
Result of Check
Causes
Solution
Pattern
The leading edge registration of "M", "C" and/or
"Y" is not correct.
1. Image transfer belt failure
2. Drive section failure
3. ID sensor failure
4. BCU(IPU) failure
5. Normal
1. Replace Image transfer belt
2. Replace PCU, drum motor
3. Replace ID sensor
4. Replace BCU(IPU)
1, 2
The skew of "M", "C" and/or "Y" is not correct.
1. PCU installation failure
2. Laser unit failure
3. IOB failure
1. Reset/Replace PCU
2. Replace laser unit
3. Replace IOB
-
Shifted Drum phase.
1. PCU installation failure
2. Drive section failure
3. Phase adjustment failure
1. Reset/Replace PCU
2. Check/Replace drive section
3. Execute SP1-902-001
5
663
664
4. Replacement and Adjustment
• Make sure that the data-in LED ( ) is not on before you go into the SP mode. This LED indicates that some data is coming to the machine. When the LED is on, wait for the copier to process the data.
• The Service Program Mode is for use by service representatives only. If this mode is used by anyone other than service representatives for any reason, data might be deleted or settings might be changed. In such case, product quality cannot be guaranteed any more.
If there are no Classic Application (copy/printer/scanner/fax) icons on the HOME screen, follow the procedure below to display the number keyboard.
1.
Press and hold the button [A] located at the left side of the operation panel and "Check
Status [B]" at the same time, until the number keyboard is displayed.
665
666
5. System Maintenance
2.
Enter the key code for SP mode.
For details of the key code to enter the SP mode, ask your supervisor.
Press "Exit" on the LCD twice to return to the copy window.
• System SP: SP modes related to the engine functions
• Printer SP: SP modes related to the controller functions
• Scanner SP: SP modes related to the scanner functions
• Fax SP: SP modes related to the fax functions
Select one of the Service Program modes (System, Printer, Scanner, or Fax) from the touch panel as shown in the diagram below after you access the SP mode. This section explains the functions of the
System/Printer/Scanner SP modes. Refer to the Fax service manual for the Fax SP modes.
Service Program Mode
Here is a short summary of the touch-panel buttons.
1 Opens all SP groups and sublevels.
2 Closes all open groups and sublevels and restores the initial SP mode display.
667
668
5. System Maintenance
3 Opens the copy window (copy mode) so you can make test copies. Press SP Mode
(highlighted) in the copy window to return to the SP mode screen,
4 Enter the SP code directly with the number keys if you know the SP number. Then press [#].
The required SP Mode number will be highlighted when pressing [#]. If not, just press the required SP Mode number.)
5 Press two times to leave the SP mode and return to the copy window to resume normal operation.
6 Press any Class 1 number to open a list of Class 2 SP modes.
7 Press to scroll the show to the previous or next group.
8 Press to scroll to the previous or next display in segments the size of the screen display (page).
9 Press to scroll the show the previous or next line (line by line).
10 Press to move the highlight on the left to the previous or next selection in the list.
1. In the SP mode, select the test print. Then press "Copy Window".
2. Use the copy window (copier mode), to select the appropriate settings (paper size, etc.) for the test print.
3. Press [Start] key to start the test print.
4. Press SP Mode (highlighted) to return to the SP mode screen and repeat from step 1.
Program numbers have two or three levels.
1. Refer to the Service Tables to find the SP that you want to adjust before you begin.
2. Press the Group number on the left side SP Mode window that contains the SP that you want to adjust.
3. Use the scrolling buttons in the center of the SP mode window to show the SP number that you want to open. Then press that number to expand the list.
4. Use the center touch-panel buttons to scroll to the number and title of the item that you want to set and press it. The small entry box on the right activates and shows the below default or the current settings.
Service Program Mode
• Refer to the Service Tables for the range of allowed settings.
5. Do this procedure to enter a setting:
• Press to toggle between plus and minus and use the keypad to enter the appropriate number. The number you enter writes over the previous setting.
• Press [#] to enter the setting. (The value is not registered if you enter a number that is out of range.)
• Press "Yes" when you are prompted to complete the selection.
6. If you need to perform a test print, press Copy Window to open the copy window and select the settings for the test print. Press [Start] key and then press SP Mode (highlighted) in the copy window to return to the SP mode display.
7. Press Exit two times to return to the copy window when you are finished.
At locations where the machine contains sensitive data, the customer engineer cannot operate the machine until the Administrator turns the service mode lock off. This function makes sure that work on the machine is always done with the permission of the Administrator.
1. If you cannot go into the SP mode, ask the Administrator to log in with the User Tool and then set
"Service Mode Lock" to OFF after he or she logs in:
User Tools > Machine Features > System Settings > Administrator Tools > Service Mode Lock > OFF
• This unlocks the machine and lets you get access to all the SP codes.
• The CE can service the machine and turn OFF then ON the machine power. It is not necessary to ask the Administrator to log in again each time the main power is turned ON.
2. Go into the SP mode and set SP5-169 to "1" if you must use the printer bit switches.
669
670
5. System Maintenance
3. After machine servicing is completed:
• Change SP5-169 from "1" to "0".
• Turn OFF then ON the machine power. Tell the administrator that you have completed servicing the machine.
• The Administrator will then set the "Service Mode Lock" to ON.
The maximum number of characters which can show on the control panel screen is limited to 30 characters. For this reason, some of the SP modes shown on the screen need to be abbreviated. The following are abbreviations used for the SP modes for which the full description is over 20 characters.
Item
Paper Weight
Paper Type
Paper Feed Station
Print Mode
Description
Thin paper: 52-59 g/m
2
, 14-15lb. Bond
Plain Paper1: 60-74 g/m
2
, 16-20lb. Bond
Plain Paper2: 75-81 g/m
2
, 20lb. Bond
Middle Thick: 82-105 g/m
2
, 20-28lb. Bond
Thick Paper1: 106-169 g/m
2
, 28lb. Bond-90lb. Index
Thick Paper2: 170-220 g/m
2
, 65-80lb. Cover
Thick Paper3: 221-256 g/m
2
, 80lb. Cover-140lb. Index
Thick Paper4: 257-300 g/m
2
, 140lb. Index-110lb. Cover
N: Normal paper
MTH: Middle thick paper
TH: Thick paper
P: Paper tray
B: Bypass tray
S: Simplex
D: Duplex
The settings of each SP mode are explained in the right-hand column of the SP table in the following way.
[Adjustable range / Default setting / Step] Alphanumeric
Service Program Mode
• If "Alphanumeric" is written to the right of the bracket as shown above, the setting of the SP mode shows on the screen using alphanumeric characters instead of only numbers. However, the settings in the bracket in the SP mode table are explained by using only the numbers.
The following symbols are used in the SP mode tables.
Notation What it means
ENG Engine SP
CTL
FA
DFU
Controller SP
Factory setting: Data may be adjusted from the default setting at the factory. Refer to the factory setting sheets enclosed. You can find it in the front cover.
Design/Factory Use only: Do not touch these SP modes in the field.
*
SSP
An asterisk (*) to the left side of ENG/CTL column means that this mode is stored in the NVRAM. If you do a RAM clear, this SP mode will be reset to the default value.
"ENG" and "CTL" show which NVRAM contains the data.
• *ENG: NVRAM on the BCU board
• *CTL: NVRAM on the controller board
This denotes a "Special Service Program" mode setting.
671
672
5. System Maintenance
See "Appendices" for the following information:
• Engine SP Tables - SP1000
• Engine SP Tables - SP2000
• Engine SP Tables - SP3000
• Engine SP Tables - SP4000
• Engine SP Tables - SP5000
• Engine SP Tables - SP6000
• Engine SP Tables - SP7000
• Input Check
• Output Check
• Controller SP Tables - SP5000
• Controller SP Tables - SP7000
• Controller SP Tables - SP8000
• Printer Service Menu
• Scanner Service Menu
Firmware Update (SD Card)
In order to update the firmware of this machine, it is necessary to download the latest version of firmware on an SD card.
Insert the SD card into SD card slot 2 beside the rear left of the controller box.
Types of firmware update files, supported update methods:
SFU SD Card RFU ARFU
Individual firmware
Package firmware
N/A
Available
Available
Available
Available
Available
N/A
Available
Firmware type
System/Copy
Engine
Operation Panel
ADF
Finisher1
Bank
FCU
Network Support
Bank2
BIOS
HDD format option
RPCS
PS
Firmware location
Controller Board
BCU
Smart Operation Panel
ADF
Finisher
Bank
FCU
Smart Operation Panel – CPU board
Bank
BCU
Controller Board
Controller Board
Controller Board
673
674
5. System Maintenance
Firmware type
PCL
PCLXL
MSIS
RPDL
R98
R16
RPGL
R55
RTIFF
PictBridge
PJL
MediaPrint: JPEG
MeidaPrint: TIFF
XPS
FONT
FONT1
FONT2
Copy apl
NetworkDocBox
Fax apl
Printer apl
Scanner apl
Remote Fax apl
MIB
Firmware location
Controller Board
Controller Board
Controller Board
Controller Board
Controller Board
Controller Board
Controller Board
Controller Board
Controller Board
Controller Board
Controller Board
Controller Board
Controller Board
Controller Board
Controller Board
Controller Board
Controller Board
Controller Board
Smart Operation Panel – CPU board
Smart Operation Panel – CPU board
Smart Operation Panel – CPU board
Smart Operation Panel – CPU board
Smart Operation Panel – CPU board
Smart Operation Panel – CPU board
Smart Operation Panel – CPU board
Firmware Update (SD Card)
Firmware type
Websupport
WebUapl
CSPF
Firmware location
Smart Operation Panel – CPU board
Smart Operation Panel – CPU board
Smart Operation Panel – CPU board
What is Included in the Firmware Package
Modules included in the firmware package are indicated by ticks ( ).
Firmware not included in the package require updating by SD cards, etc.
Firmware Included
aics animation
-
-
-
Application Site
BluetoothService
CheetahSystem
CSPF
Data Erase Onb
EcoInfoWidget
-
-
Engine
External Auth
Fax
FaxInfoWidget
GWFCU3.8-9(WW)
• An SD card is a precision device, so when you handle an SD card, respect the following.
• When the power is switched ON, do not insert or remove a card.
675
676
5. System Maintenance
• During installation, do not switch the power OFF.
• Since the card is manufactured to high precision, do not store it in a hot or humid location, or in direct sunlight.
• Do not bend the card, scratch it, or give it a strong shock.
• Before downloading firmware to an SD card, check whether write-protection of the SD card is canceled. If write-protection is enabled, an error code (error code 44, etc.) will be displayed during download, and the download will fail.
• Before updating firmware, remove the network cable from this machine.
• If SC818 is generated during software update, switch the power OFF -> ON, and complete the update which was interrupted.
• During software update, disconnect network cables and interface cables, remove wireless boards, etc., (so that they are not accessed during the update).
• If the SD card is blank, copy the entire "romdata" folder onto the SD card.
• If the card already contains the "romdata" folder, copy the "D244" folder onto the card.
• If the card already contains folders up to "D244", copy the necessary firmware files (e.g.
D244xxxx.fwu) into this folder.
• Do not put multiple machine firmware programs on the same SD card. Copy the only model firmware you want.
1.
First download the new firmware to the SD card.
2.
Turn OFF the main power.
3.
Remove the SD card slot cover [A].
4.
Insert the SD card into SD card slot 1 [A: Lower Slot].
Firmware Update (SD Card)
• Check whether the card is properly in the SD card slot. When a SD card is inserted, a click is heard, and it is locked.
• To remove the card, release by pressing once.
5.
Turn ON the main power.
6.
Wait until the update screen starts (about 45 seconds).
When it appears, "Please Wait" is displayed.
7.
Check whether a program installation screen is displayed. (English display) When the SD card contains two or more software modules, they are displayed as follows.
<<When two or more software names are displayed>>
1. Press the module selection button or [1] - [5] on the 10-key pad.
2. Choose the appropriate module. (If already selected, cancel the selection)
Operation of keys or buttons
Keys or buttons to press
[Exit] or 10-key pad [0]
[Start] Key
[Clear/Stop] key
Returns to normal screen.
Select all modules.
Cancel all selections.
Contents
677
5. System Maintenance
Display contents
On the above screen, two programs, i.e., engine firmware and printer application are displayed.
(The screen may change depending on the firmware or application).
The display contents are as follows:
Display
ROM:
NEW:
Contents
Display installed module number / version information.
Display module number / version information in the card.
The upper row corresponds to the module name, the lower row corresponds to the version number.
8.
Select the module with the module selection button or 10 key pad operation. The selected module is highlighted, and [Verify] and [Update] are displayed.
• Depending on the combination of modules to update, it may not be possible to select all of them simultaneously.
678
<<Key or button operations>>
Keys or buttons to press Contents
[Update] or [#] key
[Verify] button or [./*] key
Update the ROM of the selected module.
Perform verification of the selected module.
9.
Press the [Update] or [#] key, and perform software update.
Firmware Update (SD Card)
10.
During firmware update, a "firmware update/ verification progress screen" is displayed.
When firmware update is complete, a "firmware update end screen" is displayed.
• In the middle row, the name of the module currently being updated is displayed. (in this case, the printer module is being updated)
• In the lower row, a progress bar is displayed in ten steps. (The more *, the more the progress.)
<<Firmware update end screen>>
• This screen is displayed when all selected firmware modules are to be updated. "Printer" in the second row shows that the module updated last is the printer. (When more than one were updated simultaneously, only the module that was updated last is displayed.)
• When Verify has completed normally, the Update done display of the above screen is "Verify done." If "Verify Error" is displayed, reinstall the software of the application displayed in the lower row.
11.
After turning the main power OFF, remove the SD card.
12.
Turn the main power ON again, and check whether the machine is operating normally.
13.
Return the SD card slot cover to the original position.
• When the power supply is switched OFF during firmware update, update is interrupted, and the power is switched ON again, normal operation cannot be guaranteed.
• To guarantee operation, an update error continues to be displayed until update is successful.
• In this case, insert the SD card again, switch the power ON, and continue download of firmware from the SD card automatically.
679
5. System Maintenance
• The PS3 firmware program is included in the preinstalled PDF firmware. In the default state, although the PS3 firmware program is hidden in the disabled state, the function is enabled by installing the PS3 card. (The program installed in the PS3 card is a dongle (key) for enabling the
PS3 function).
• Due to the above specification, the self-diagnosis result report shows the ROM module number / software version of the PDF firmware at the PS location.
680
EXX shows an error code.
For error codes, refer to the following table:
Error Code List
Code
20
Contents
Physical address mapping cannot be performed.
21
22
Insufficient memory for the download
Decompression of compressed data failed.
Solutions
• Switch the main power supply off and on to try again.
• Re-insert the SD card to reboot it.
• Replace the controller board if the above solutions do not solve the problem.
• Switch the main power supply off and on to try again.
• Replace the controller board if the updating cannot be done by switching the power off and on.
• Switch the main power supply off and on to try again.
• Replace the SD card used for the update.
• Replace the controller board if the above solutions do not solve the problem.
Firmware Update (SD Card)
Code
24
32
33
34
35 interruption.
Contents
SD card access error
The SD card used after download suspension is incorrect.
SD cards are different between the one which was inserted before power interruption and the one which was inserted after power
Card version error.
The wrong card version is downloaded.
Destination error.
A card for the wrong destination is inserted.
Model error.
A card for the wrong model is inserted.
Solutions
• Re-insert the SD card.
• Switch the main power supply off and on to try again.
• Replace the SD card used for the update.
• Replace the controller board if the above solutions do not solve the problem.
• Insert the SD card containing the same program as when the firmware update was suspended, and then switch the main power supply off and on to try again.
• There is a possibility that the SD card is damaged if the update cannot be done after the correct SD card has been inserted. In this case, try again with a different SD card.
• Replace the controller board if the above solutions do not solve the problem.
Replace all relevant boards if the update is done for the BCU and FCU.
Replace the operation panel unit if the update is done for the operation panel.
• Install the correct ROM update data for each version in the SD card.
• Install the correct ROM update data for each destination (JPN/ EXP/ OEM) in the
SD card.
• Install the correct ROM update data for each model in the SD card.
681
682
5. System Maintenance
Code
36
38
40
41
42
43
Contents
Module error.
The program to be downloaded does not exist on the main unit.
The download destination specified by the card does not match up to the destination for the main unit’s program.
The version of the downloaded program has not been authorized for the update.
Engine download fails.
Solutions
• Install the program to be updated in advance.
• There is a possibility that the SD card containing the program to be updated has not been mounted. Check to confirm that the
SD card has been correctly mounted.
• The SD card is incorrect if the program to be updated has been correctly installed. In this case, insert the correct SC card.
• Make sure that the program to be overwritten is the specified version.
Fax download fails.
Control panel / language download fails.
Printing download fails.
• Switch the main power supply off and on to try again.
• If the download fails again, replace the controller board and the BCU.
• Switch the main power supply off and on to try again.
• If the download fails again, replace the controller board and the FCU board.
• Switch the main power supply off and on to try again.
• If the download fails again, replace the controller board and the operation panel unit.
• Switch the main power supply off and on to try again.
• The SD card is damaged if the update fails again. Replace the SD card.
Firmware Update (SD Card)
58
59
60
Code
44
49
50
57
61
62
63
Contents
The data to be overwritten cannot be accessed when controllerrelated programs are downloaded.
Firmware updates are currently prohibited.
The results of the electronic authorization check have rejected the update data.
@Remote is not connected at the date/time reserved for receiving the package firmware update from the network.
Update cannot be done due to a reception route problem.
HDD is not mounted.
HDD could not be used during the package firmware update.
Solutions
• Switch the main power supply off and on to try again.
• Install the correct ROM update data in the
SD card.
• Replace the controller board if the data to be overwritten is contained on the controller board.
• The setting of Update Firmware in the
Administrator Tools has been set to [Prohibit] by an administrator. Amend the setting to
[Do not Prohibit] and try again.
• Install the correct ROM update data in the
SD card.
• Check the @Remote connection.
• Check the @Remote connection.
• Check the HDD connection.
• Try again.
• Replace the HDD if the download fails again.
• Prepare the correct package files.
The module ID for the package firmware update is incorrect.
The configuration of the package firmware update files is incorrect.
Reception fails due to the power off at the reserved date/time of the remote firmware update from the network.
• Prepare the correct package files.
• Update is to be done automatically when the next reception time has elapsed.
683
684
5. System Maintenance
Code
64
65
66
67
68
69
70
71
72
Contents
Reception fails due to the power off at the reserved date/time of the package firmware update from the network.
Reception fails due to the status error of the machine at the reserved date/time of the remote firmware update from the network.
Reception failed due to the status error of the machine at the reserved date/time of the package firmware update from the network.
Acquisition of the latest version information from the Gateway fails at the reserved date/time of the remote firmware update from the network.
Acquisition of the latest version information from the Gateway fails.
Download fails at the reserved date/time of the remote firmware update from the network.
Package firmware download from the network fails.
Network communication error occurs at the reserved date/time of the package firmware update from the network.
The setting of @Remote is invalid at the reserved date/time of the package firmware update from the network.
Solutions
• Reset the reservation date/time for the remote update.
• Update is to be done automatically when the next reception time has elapsed.
• Reset the reservation date/time for the remote update.
• Check that the network is connected correctly.
• Check that the network is connected correctly.
• Check that the network is connected correctly.
• Check that the network is connected correctly.
• Check that the network is connected correctly.
• Set the setting of @Remote Service in the
Administrator Tools to [Do not Prohibit].
Firmware Update (SD Card)
• The PDF firmware installed as standard contains the program required to print PS3 data by default.
However, this PS3 program is normally disabled.
• The PS3 firmware is a dongle (key) which enables PS3 data printing functions. When the PS3 firmware is installed, the PS3 program in the PDF firmware is enabled. Due to this specification, the self-diagnosis result report shows the ROM part number/software version of the PDF firmware contained in the PS3 program.
685
5. System Maintenance
In this machine, software can be updated by remote control using @Remote.
686
Types of firmware update files, supported update methods:
SFU SD
Individual firmware
Package firmware
N/A
Available
Available
Available
RFU is performable for a device which meets the following conditions.
1. The customer consents to the use of RFU.
2. The device is connected to a network via TCP/IP for @Remote.
RFU
Available
Available
ARFU
N/A
Available
Firmware Update (Smart Firmware Update)
• A HDD unit must be installed on the machine to enable the SFU or the package firmware update via SD card.
Each firmware module (such as System/Copy, Engine, etc.) used to be updated individually. However, an all-inclusive firmware package (package_ALL) is now available.
There are two ways to update using the firmware package.
• Package firmware update via a network: SFU (Smart Firmware Update)
• Package firmware update with an SD card
Package firmware update via a network: SFU (Smart Firmware Update)
• There are two methods for SFU.
• Immediate Update: To update the firmware when visiting
• Update at the next visit: To set the date and time for downloading. The firmware will be automatically downloaded beforehand and updated at the following visit.
• "Update at the next visit" is recommended since firmware download may take some minutes due to the network condition.
• SFU requires the connection to @Remote via a device which has the embedded @Remote communicating function. When a machine is connected to @Remote via an intermediate device (RC Gate), the SFU function is disabled.
Package firmware update via an SD card
Package firmware update can also be performed using the conventional SD card method by writing the package firmware directly to the SD card.
687
688
5. System Maintenance
Types of firmware update files, supported update methods:
SFU SD Card
Individual firmware
Package firmware
N/A
Available
Available
Available
RFU
Available
Available
ARFU
N/A
Available
Enter the [Firmware Update] menu in the SP mode and update the package firmware.
• The [Firmware Update] button will appear even when a machine is connected to @Remote with a device which does not have an embedded @Remote communicating function.
• If an error code is displayed, refer to page 680 "Error Screens During Updating".
1.
Enter the SP mode.
2.
Press [Firmware Update].
3.
Press [Update].
4.
Press [Execute Update].
5.
Press [YES].
6.
The following will be displayed.
Firmware Update (Smart Firmware Update)
• If the error code E66, which indicates that the download of the firmware has failed, is displayed, go back to step 1.
689
690
5. System Maintenance
• Update will be started automatically after the download is finished.
• When the machine is in the update mode, the automatic update is suspended if a print job is started. After the print job is finished, press [YES] on the display shown below to restart updating.
7.
[Update done] is displayed.
• The machine will automatically reboot itself.
Firmware Update (Smart Firmware Update)
• The figures at the lower right of the display indicate "Number of updated items/ All items to be updated".
It is possible to set the machine to download the package firmware which is necessary for SFU in advance, and then perform the actual installation at the next service visit. This saves waiting time for the firmware to download at the service visit.
Enter the [Firmware Update] menu in the SP mode and update the package firmware.
• The [Firmware Update] button will appear even when a machine is connected to @Remote with a device which does not have an embedded @Remote communicating function. If an error code is
displayed, refer to page 680 "Error Screens During Updating".
1.
Enter the SP mode.
2.
Press [Firmware Update].
691
692
5. System Maintenance
3.
Press [Reserve].
4.
Press [Reservation setting].
5.
Enter the dates and times of the next visit and the start of receiving data.
• "Next time to visit this customer": The package firmware will be automatically downloaded by this time/date.
• "When to receive? (1-7)": The download of the package firmware will begin this number of days before the next visit.
Firmware Update (Smart Firmware Update)
Successful Download
In the two diagrams below, the firmware is set to be downloaded by the day before the next scheduled visit. In the first diagram, the download is successful on the first try. In the second diagram, the download fails three times and is successful on the fourth try.
• If the firmware download fails or cannot be completed due to the network settings/condition, no power to the machine, or other reason, the machine will continue retrying every six hours until the scheduled deadline (up to a maximum of four tries). For example, if the download is set for the day before the next visit, the machine will attempt the download at 24 hours before the visit, and then continue trying every six hours (max. four tries total).
• The retry is only performed in cases when the firmware download has failed.
• If the machine is in Energy Saver mode when the download is scheduled to begin, the download will be performed in the background and the machine/panel will stay in Energy Saver mode.
• The download will continue uninterrupted even if the customer initiates a print job, copy job, fax receiving or other operation while the download is in progress.
• The download will be terminated if the customer turns the power off while the download is in progress.
• If the download cannot be completed successfully by the time of the next scheduled visit, the machine will stop trying to download the firmware.
1.
Enter the SP mode.
693
5. System Maintenance
2.
Press [Firmware Update].
3.
Press [Reserve].
4.
Press [Reserve and received package information].
694
5.
Check the information displayed.
When the package firmware was downloaded successfully, the details of the download result are displayed as the following picture shows.
Firmware Update (Smart Firmware Update)
• This information will only be displayed if the reserved firmware has already been downloaded. If not, all the data items are indicated with "-".
1.
Enter the SP mode.
2.
Press [Firmware Update].
695
696
5. System Maintenance
3.
Press [Update].
4.
Press [Execute Update].
5.
Check the version of the received package firmware, and then press [YES].
• Update is started.
Firmware Update (Smart Firmware Update)
• If the version of the reserved package in the HDD is older than the latest version, the messages shown in the following picture are displayed.
• If you wish to download the latest version, press [Execute] beside the message "Download and update the latest package." Then update of the package firmware will be started.
• If you wish to update using the firmware in the HDD (old version), press [Execute] beside the message "Update to the received package."
6.
[Update done] is displayed.
• The machine will automatically reboot itself.
697
5. System Maintenance
698
• The figures at the lower right of the display indicate "Number of updated items/ All items to be updated".
Update with an SD card, which is the conventional method, is available if you write the package firmware to the SD card.
• If an error code is displayed, refer to page 680 "Error Screens During Updating".
1.
Create a new folder in the SD card, and then name it "package".
2.
Copy the package firmware (xxxxxxxx.pkg) to this folder.
Firmware Update (Smart Firmware Update)
• If you copy the package firmware into the conventional "romdata" folder, the update will not work.
• Only one version of the package firmware should be copied into the folder. If you copy multiple versions of package firmware to the SD card, the machine will select only one version of the firmware randomly.
3.
Turn the power OFF.
4.
Insert the SD card which contains the package into SD card slot 2 (for service).
5.
Turn the power ON and press [Update].
• When the SD card contains both a firmware package and one or more modules, the following display may show up. Select [Package] and press [OK] to move to step 5 above.
699
5. System Maintenance
6.
Update is started automatically after the package firmware download to the HDD has been completed.
7.
When update is completed, "Update done" is displayed.
700
• The figures at the lower right of the display indicate "Number of updated items/ All items to be updated".
8.
Turn the main power switch OFF, and then pull out the SD card from SD card slot 2.
9.
Turn the power ON.
Firmware Update (Auto Remote Firmware Update)
• Auto remote firmware update (ARFU) requires connection to the Internet. Be sure to get permission from the customer before setting.
By Auto Remote Firmware Update (ARFU), the firmware is updated by checking the global server every
76 hours and downloading the latest package if it is newer than the one installed on the machine.
Function Overview
Types of firmware update files, supported update methods:
SFU SD Card
Individual firmware
Package firmware
N/A
Available
Available
Available
RFU
Available
Available
ARFU
N/A
Available
What is Included in the Firmware Package
Modules included in the firmware package are indicated by ticks ( ) in the firmware download web site.
Firmware not included in the package require updating by SD cards, etc.
Firmware Included
aics animation
Application Site
701
702
5. System Maintenance
Included
-
-
-
-
-
BluetoothService
CheetahSystem
CSPF
Data Erase Onb
EcoInfoWidget
Engine
External Auth
Fax
FaxInfoWidget
GWFCU3.8-9(WW)
Firmware
Firmware Update (Auto Remote Firmware Update)
The machine checks the server for the latest package version.
If the version of the package on the global server is later than that of the package installed on the machine, or if the machine has not downloaded the firmware package, the machine downloads the latest package in the background even when the customer is using the machine.
If download fails, the machine will retry downloading 76 hours later.
The downloaded package can also be used with SFU (Smart Firmware Update). A package downloaded with SFU (Smart Firmware Update) can be used with ARFU (Auto Remote Firmware
Update) and vice versa.
When replacing the hard disk, the firmware package data becomes lost from the hard disk. Even if the latest firmware is on the new hard disk, be sure to receive the latest package data.
When the machine connects to the server where the package files are stored, the DNS settings and the name solution by DNS are needed. The machine will still try to download the package even if the name cannot be resolved, but will fail as the name is not resolved.
The time and date to send the next inquiry to the global server can be checked with SP5-886-116 (Farm
Update Setting: Auto Update Next Date).
The auto remote firmware update is executed every 76 hours.
Update judgement is done when the latest update package is successfully downloaded, or the package has already been downloaded.
If the judgement timing is in the range of the update prohibited time or day set with SP or WIM, the machine will retry the update after 76 hours.
703
5. System Maintenance
If the machine is in use when the judgement process runs, the process is retried. Retry is done up to three times every hour (can be changed with SP) and if the machine is in use for all three retries, the machine will retry the update after 76 hours
704
Situations judged as machine in use
No.
Situations judged as machine in use
1 When the control panel is used within 30 seconds
2 During firmware update
3 While firmware update is disabled
4 While printing (copy, printer, fax, re-printing via network)
Firmware Update (Auto Remote Firmware Update)
No.
Situations judged as machine in use
5 While scanning (copy, scanner, fax)
6 Retrieving image data via network
7 While initial setting (User Tools settings) or SP is being set
8 While fax is transferring data
9 During on hook / on handset
10 During the PC-FAX process (from PC to machine data transfer to the end of the job)
11 While shifting to/from the energy server mode
12
When not being able to run firmware update due to the modules that are running e.g.) Waiting for DCS transfer (refer to appendix), accessing devices such as HDD/SD card, etc.
13 While displaying a preview
14 While the document server function is in use
15 Connecting to TWAIN
16 During the interrupt copy process
17 While displaying the printer menu
18
While updating the display for the document server function via WIM or for stored fax documents
19 While writing log information
20 While accessing the address book
21 During SC
When the machine has decided to run the auto firmware update, the following message is displayed.
705
5. System Maintenance
706
The popup will have "Cancel" and "OK" buttons and the update process will start either when the "OK" button is selected or 30 seconds has passed.
When the "Cancel" button is selected, the machine will run the "Retry update" process.
When the device update and three retries in recovery mode both fail, it is determined as a device defect and will display an SC for the defective device. If such an SC appears, replace the indicated board. In the case of SC845, the SC cannot be reported to the call center.
Device and corresponding SC number.
Device name
Engine board
SC number
SC845-01
Controller board
Operation panel (normal panel)
Operation panel (smart panel)
FCU
SC845-02
SC845-03
SC845-04
SC845-05
Canceling the update
It is possible to cancel the Auto Remote Firmware Update (ARFU) or update in recovery mode from the operation panel.
Firmware Update (Auto Remote Firmware Update)
But this is not possible while updating the operation panel itself. On the other hand, the update for the operation panel will run at the final stage of the update. Thus canceling the update at that stage has no real effect.
When the update is cancelled, the machine will reboot when updates for all modules of one of the following devices is done.
1. Engine Board
2. FCU
3. Controller Board
4. Operation Panel
For example, when the update process is cancelled while updating the first module of the operation panel, the machine will reboot when all modules in the operation panel have been updated.
The firmware contents included in the package can be referred to in the release note in SERES release of the package.
The next update will run 76 hours after the cancellation. The old (cancelled) package will be discarded if the package downloaded 76 hours later is the latest.
707
708
5. System Maintenance
1.
Enter the SP mode.
2.
Press [Firmware update].
3.
Press [Update].
4.
Press [Update Package Information].
5.
If the firmware package is the same as the one on the global server, the update was completed successfully. Otherwise, check the result using the logging date.
In SP7-520-041 to -045 (Update Log: Auto:Version), you can check the versions of the packages updated by ARFU. (-041 displays the latest result. It is also printed on the SMC sheet.)
1.
Enter the SP mode.
2.
Press [System/Copy].
3.
Check the results for ARFU by SP7-520-051 to 060 (Update Log: Auto:Result)
"-051" is the latest update result. For details about the number of each result log, see next section
“Related SP.”
SP Number
SP5-886-111
SP5-886-112
SP5-886-113
SP5-886-114
Selection
Def.
0: OFF
1: ON
0: OFF
1: ON
0 to 23
9
0 to 23
17
Overview
Sets auto update ON/OFF by ARFU.
Will not run the update when update prohibited time setting is ON and the current time is in the range of the time set.
• Start time < End time: Prohibited time is from the start time to the end time on the same day.
• Start time > End time: Prohibited time is from the start time to the end time on the next day.
• Start time == End time: Prohibited time setting is disabled.
(Update will not be prohibited.)
Firmware Update (Auto Remote Firmware Update)
SP Number
SP5-886-115
Selection
Def.
0: OFF
1: ON
Overview
Even when the update function is disabled, downloading the package is allowed.
The downloaded package can be used with SFU.
SP5-886-116 Display only Displays when the latest package check will run.
SP5-886-117
1 to 24
1
Set time for the next version check after retry.
SP5-886-120
SP7-520-011 to 015
SP7-520-021 to 025
0x00 Update will not run if the corresponding bit for each day below is set to 1.
• prohibited:bit7
• Monday: bit 6
• Tuesday: bit 5
• Wednesday: bit 4
• Thursday: bit 3
• Friday: bit 2
• Saturday: bit 1
• Sunday: bit 0
This setting is not affected by the prohibited time setting.
e.g.) Prohibited on Mon., Fri., Sat., and Sun. : 0x47 (01000111)
Display only History of date and time when update has started.
The five most recent are recorded, the lowest number being most recent.
If the last update failed, this is not recorded.
Display only History of date and time when update has finished.
The five most recent are recorded, the lowest number being most recent.
The record is created when the update has successfully finished.
When the update is cancelled, no record is created.
709
710
5. System Maintenance
SP Number
SP7-520-031 to 035
SP7-520-041 to 045
SP7-520-051 to 060
Selection
Def.
Overview
Display only History of the package number (including suffix) for which update has completed.
The five most recent are recorded, the lowest number being most recent.
The record is created when the update has successfully finished.
When the update is cancelled, no record is created.
Display only History of the package version for which update has completed.
The five most recent are recorded, the lowest number being most recent.
The record is created when the update has successfully finished.
When the update is cancelled, no record is created.
Display only History of the result of the download and the update.
Refer below for the numbers set.
Numbers set for the result history for SP7-520-051 to 060
No.
1
Result
Downloading with SFU
Description
Cannot download or update as the machine is now downloading the package for SFU.
2
3
HDD uninstalled
Updating with SFU
Cannot download or update as the machine has no
HDD.
Cannot download or update as the machine is being updated with SFU.
4
5
6
HDD error
Version information obtain error
Update download error
Cannot download or update as the HDD cannot be used.
Cannot download or update as the version information cannot be obtained.
Cannot download or update as the update download failed.
In non @Remote method, this shows that the download failed because there was no proxy set.
Firmware Update (Auto Remote Firmware Update)
No.
7
8
9
Result
Name resolution error
Auto update setting disabled
Update prohibited time
10
Update postponed due to machine in use
11 Update cancelled by user
12 Offline failed
13 Update successful
14 Update failed
Description
Cannot download or update as the name cannot be resolved upon downloading the update.
The package has been downloaded but will not run the update as SP5-886-111 (auto update setting) is disabled and SP5-886-115 (auto download setting for
SFU) is enabled.
Cannot start to update as the auto update prohibited time setting (SP5-886-112) is enabled and the time update initiated was in the range of prohibited time
(SP5-886-113 to 114).
Or the day which update was initiated was a day for which update was prohibited (SP5-886-120).
Cannot start update due to the following conditions when update was initiated.
• The machine is in use by a user (the panel was used within 30 seconds)
• Machine offline for other reasons
• Operation prohibited
• Displaying SP/UP menu
• Firmware update is running with another method
• Configuration change prohibited
• Verifying the operation panel (smart panel)
Update was cancelled because a user selected
"Cancel" in the popup shown before starting the update.
Cannot start to update as the machine is offline for other reasons.
Update was started and successfully completed.
Update was started but failed.
711
712
5. System Maintenance
No.
Result
15 Update deemed completed
Description
Update was cancelled after the process was initiated because a user selected “Cancel”. There is no need to resume the update due to one of the following reasons:
• A newer update has been released and received.
• When retrying ARFU, the update has already been completed by another method.
Update was cancelled after the process initiated because a user selected "Cancel" during the update.
16
17
Update cancelled by user after update initiated
Version information obtain error
(communication error occurred for hostname)
Cannot download or update as the name cannot be resolved when obtaining version information.
18
19
20
21
Version information obtain error
(proxy verification failure)
Version information obtain error
(other than proxy verification failure when proxy is set)
Update download error (proxy verification failure)
Update download error (other than proxy verification failure when proxy is set)
22 Update by retry successful
Cannot download or update as the proxy verification failed with proxy settings when obtaining version information.
Cannot download or update as an error other than proxy verification with proxy settings occurred when obtaining version information.
Cannot download or update as the proxy verification failed with proxy settings when downloading the package.
Cannot download or update as an error other than proxy verification with proxy settings occurred when downloading the package.
After power failure, unsuccessful update, or rebooting, update by retry is executed successfully.
However, this does not apply to the case where the update was cancelled after the process was initiated because a user selected “Cancel”.
In this case, the update is “successful” if the retry is not executed between the start and completion of the next update (76 hours after the cancellation).
Updating JavaVM
1.
Download the update modules from Firmware Download Center. As one of the model modules, "Java VM v11 UpdateTool" is available for download. (The version differs depending on the model.)
2.
Unzip the downloaded file. Copy the whole "sdk" folder to the root of the SD card directly below.
• When unzipping the downloaded file, two subfolders ("update" and "sdk") exist in the "sdk" folder.
Rather than just copying the subfolder "sdk", copy the whole folder "sdk".
• SD card can be inserted with the machine power off.
• During the updating process, do not turn off the power.
• If you turn off the power during the updating, the machine performance is not guaranteed. (There is a possibility that an SC and boot failure occurs.)
• If you accidentally turn off the power during the updating, retry the updating procedure from the beginning. (If the update fails again, you will need to replace the controller board.)
1.
If the boot priority application is set to the ESA application, switch to the copy application.
([System Settings]-[General Features]-[Function Priority])
2.
Take a note of the current Heap size. ([Extended Feature Settings] – [Administrator Tools]
– [Heap/Stack Size Settings])
The Heap size setting is changed to the initial setting when updating.
3.
Turn OFF the main power.
4.
Insert the SD card for update into the service slot.
5.
Turn ON the main power.
6.
After booting Java VM, update of the application is started. "Updating SDK/J" appears in the banner message of the touch panel display. (Estimated time: about 2 minutes)
713
714
5. System Maintenance
7.
After completing the update and starting the Java VM, "Update SDK / J done SUCCESS" appear in the banner message of the touch panel display. After turning off the power, remove the SD card from the slot.
When you fail to update, "Update SDK/J done FAIL" is displayed. You can confirm the cause of the error message below.
8.
Turn ON the main power.
9.
Reconfigure the Heap size. ([Extended Feature Settings]-[Administrator Tools]-[Heap/
Stack Size Settings]).
See the manual for the ESA application to know what value to set for the heap size.
10.
Return to the previous setting for the boot priority application.
Update results are output as a text file on the SD card called "sdkjversionup.log" in the "\sdk \update" folder.
Result File contents
Success
Failure script file = /mnt/sd0/sdk/update/bootscript
2012/08/22 17:57:47 start
2012/08/22 17:59:47 end SUCCESS script file = /mnt/sd0/sdk/update/bootscript
2012/08/22 17:57:47 start
XXXX Error
2012/08/22 17:57:57 end FAIL
Description of the output
Boot script path
Boot scripts processing start time
End time boot script processing, the results
Boot script path
Boot scripts processing start time
Error message (Possibly multiple)
End time boot script processing, the results
Error Message
PIECEMARK
Error,machine=XXXXX pasePut() - error : The file of the copy origin is not found
Put Error!
Cause
Applied the wrong updating tool
(Using the updating tool of a different model)
Inadequacy with the SD card for updating
(Files are missing in the updating tool)
Remedy
Use the correct updating tool for this model.
Re-create the SD card for updating.
Updating JavaVM
Error Message paseCopy() - error : The file of the copy origin is not found.
Copy Error!
[file name: XX] error,No space left on device pasePut() - error : The destination directory cannot be made.
pasePut() - error : fileCopy Error.
Put Error!
[file name: XX] error,No space left on device paseCopy() - error : The destination directory cannot be made.
paseCopy() - error : fileCopy
Error.
Copy Error!
Put Error! *1
Copy Error! *1
Delete Error!
[XXXXX] is an unsupported command.
Version Error
Cause
Inadequacy SD card for updating
(Files in the updating tool are missing)
Writing destination is full. (The
NAND flash memory on the controller board is full.)
Writing destination is full. (The
NAND flash memory on the controller board is full.)
Error, not normally expected to occur
Remedy
Inadequacy SD card for updating
(Files in the updating tool are missing)
Uninstall the unnecessary SDK applications.
If you can not uninstall it, implement escalation, stating the "model name, application configuration, SMC sheet
(SP5-990-006/024/025), and error file."
Uninstall the unnecessary SDK applications.
If you can not uninstall it, implement escalation stating the "model name, application configuration, SMC sheet
(SP5-990-006/024/025), and error file."
If you cannot uninstall it, implement escalation stating the "model name, application configuration, SMC sheet
(SP5-990-006/024/025), and error file."
*1
Without the foregoing error message, only "Put Error /
Copy Error" will be displayed
715
5. System Maintenance
Do the following procedure to upload SP code settings from NVRAM to an SD card.
• This data should always be uploaded to an SD card before the NVRAM is replaced.
• Make sure that the write protection of an SD card is unlocked.
1.
Do SP5-990-001 (SP Print Mode: All(Data List)) before you switch the machine off. You will need a record of the NVRAM settings if the upload fails.
Make sure to shut down and reboot the machine once before printing the SMC. Otherwise, the latest settings may not be collected when the SMC is printed.
2.
Turn OFF the main power.
3.
Remove the SD card slot cover [A].
4.
Insert the SD card in Service Slot [A: Lower Slot].
716
5.
Turn ON the main power.
6.
Execute SP5-824-001 (NVRAM Data Upload) and then press the "Execute" key.
NVRAM Data Upload/Download
7.
The following files are coped to an NVRAM folder on the SD card when the upload procedure is finished. The file is saved to the path and the following filename:
NVRAM\<serial number>.NV
Here is an example with Serial Number "K5000017114":
NVRAM\K5000017114.NV
8.
In order to prevent an error during the download, be sure to mark the SD card that holds the uploaded data with the number of the machine from which the data was uploaded.
• You can upload NVRAM data from more than one machine to the same SD card.
Do the following procedure to download SP data from an SD card to the NVRAM in the machine.
• The NVRAM data download may fail if the SD card with the NVRAM data is damaged, or if the connection between the controller and BCU is defective.
• Do the download procedure again if the download fails.
• Do the following procedure if the second attempt fails:
• Enter the NVRAM data manually using the SMC print you created before uploading the NVRAM data.
1.
Turn OFF the main power.
2.
Remove the SD slot cover.
3.
Insert the SD card with the NVRAM data into SD Card Slot 2 (lower).
4.
Switch ON the main power.
5.
Do SP5-825-001 (NVRAM Data Download) and press the "Execute" key.
• The serial number of the file on the SD card must match the serial number of the machine for the NVRAM data to download successfully. The download fails if the serial numbers do not match.
This procedure does not download the following data to the NVRAM:
• Total Count
• C/O, P/O Count
717
718
5. System Maintenance
The following information is possible to be uploaded and downloaded.
• Registration No.
• User Code
• Protection Code
• Fax Destination
• Fax Option
• Group Name
• Key Display
Information
• Select Title
• Folder
• Local Authentication
• Folder Authentication
• Account ACL
• New Document Initial ACL
• LDAP Authentication
1.
Prepare a formatted SD card.
2.
Make sure that the write-protection on the SD card is off.
3.
Turn OFF the main power.
4.
Remove the SD card slot cover [A].
5.
Insert the SD card in Service Slot [A: Lower Slot].
Address Book Upload/Download
6.
Enter the SP mode.
7.
Do SP5-846-051 (Backup All Addr Book).
8.
Exit the SP mode, and then turn OFF the main power switch.
9.
Remove the SD card form the SD card slot 2 (lower).
10.
Install the SD slot cover.
• If the capacity of SD card is not enough to store the local user information, an error message is displayed.
• Carefully handle the SD card, which contains user information. Do not take it back to your location.
1.
Turn OFF the main power.
2.
Remove the SD slot cover at the left rear side of the machine.
3.
Install the SD card, which has already been uploaded, into the SD card slot 2 (lower).
4.
Turn ON the main power.
5.
Enter the SP mode.
6.
Do SP5-846-052 (Restore All Addr Book).
7.
Exit the SP mode, and then turn OFF the main power switch.
8.
Remove the SD card form the SD card slot 2 (lower).
9.
Install the SD slot cover.
• The counter in the user code information is initialized after uploading.
• The information of an administrator and supervisor cannot be downloaded nor uploaded.
• If there is no data of address book information in the SD card, an error message is displayed.
719
720
5. System Maintenance
With this feature, you can save device logs that are stored in the machine (HDD or operation panel) or an SD card. It allows the Customer Engineer to save and retrieve error information for analysis.
The Capturing Log feature saves device logs for the following four.
• Controller device log including operation log
• Engine device log
• FCU device log
• Operation panel log
• In older models, a technician enabled the logging tool after a problem occurred. After that, when the problem had been reproduced, the technician was able to retrieve the device log.
• However, this new feature saves the device logs at the time that problems occur. Then you can copy the logs to an SD card.
• You can retrieve the device logs using a SD card without a network.
• Analysis of the device log is effective for problems caused by the software. Analysis of the device log is not valid for the selection of defective parts or problems caused by hardware.
• Make sure to shut down and reboot the machine once before retrieving the Debug Logs.
Otherwise, the latest settings may not be collected when the debug logs are retrieved.
Types of device logs that can be saved
Type Storage Timing Destination (maximum storage capacity)
Controller device log including operation log
Engine device log
• Saved at all times HDD (4 GB) or SD card connected to the service slot.
When the data gets over 4.0 GB, the older data is deleted.
HDD or SD card connected to the service slot (Up to 300 times)
• When an engine SC occurs
• When paper feeding/output stop because of a jam
• When the machine doors are opened during normal operation
Capturing the Device Logs
Type Storage Timing
FCU device log • When a specified amount of
FCU device log is stored in the
FCU. If fax application is unavailable (e.g. not installed), the machine does not transfer the log.
Operation panel log • When an error related to the operation panel occurs.
Destination (maximum storage capacity)
HDD or SD card connected to the service slot
Memory in the operation panel.
• Device logs are not saved in the following conditions:
• While erasing all memory
• While data encryption equipment is installed
• While changing the firmware configuration
• Forced power OFF (accidentally disconnecting the outlet)
• Engine device log while the machine is shutting down
• When the power supply to the HDD is off because of energy saving (engine OFF mode/STR mode)
• When one of the following SCs occurs: SC672, SC816, SC819, SC878, SC899, SC859,
SC860, SC861, SC863, or SC864
• The following logs are not saved:
• Logs related to the energy saver mode (Engine-off, suspend-mode, or other cases)
Network communication log
Logs related to NRS
IP-FAX log
Access log for unauthorized users (guests)
• HTTP session timeout log
• Auto log-out log
• IC card related log
• Authorization for Fax
• The default save destination is the HDD. Except when it cannot be saved to the HDD for some reason, there is no need to change from the HDD to an SD card.
721
722
5. System Maintenance
• If you want to change the save destination to an SD card, do the following.
1. Set SP5-858-002 (Collect Machine Info: Save To) to ”1 (SD)”
2. Execute SP5-858-003 (Collect Machine Info: Make Log Trace Dir) to make a folder for the log in the SD card.
3. Turn the power switch OFF and ON.
• It is recommended to use the SD card (8 GB) provided as a service part. The part number of the SD card that is registered as a service part is "B6455040".
The following operation logs related to security are not saved.
• User ID
• Password
• IP address
• Telephone number
• Encryption key
• Transition to SP mode
• Retrieve device logs to identify the date of occurrence of the problems and to find details of the problems
• e.g.: At around 8:00 am on March 10, an engine stall occurred. The operation panel does not respond. Turn the main power supply off / on.
• Analysis of the device log is effective for problems caused by the software. Analysis of the device log is not valid for the selection of defective parts or problems caused by hardware.
1.
Insert the SD card into the slot on the side of the operation panel or the service slot.
• It is recommended to use the SD card (2 GBs* or 8 GBs**) provided as a service part. This is because the log data can be acquired much faster than when using commercially available
SD cards.
• Format the SD card by using SD Formatter from Panasonic before copying the logs: https:// www.sdcard.org/downloads/formatter_3/ (free software)
Capturing the Device Logs
• Insert the SD card into the machine's service slot instead of the SD slot on the side of the operation panel.
* The part number of the SD card with 2 GBs that is registered as a service part is "B6455030".
** The part number of the SD card with 8 GBs that is registered as a service part is "B6455040".
2.
Turn ON the main power.
3.
Enter SP mode.
4.
Specify the date that the problem occurred in SP5-858-101 (Start Date) by setting it to the year-month-day calendar format.
• For example, if a problem occurred on February 1, 2015, the date should be set to
"20150201", as shown above.
• Be sure to confirm the date when the problem occurred before obtaining the logs.
5.
Specify the number of days to collect the logs in SP5-858-102 (Days of Tracing).
• "2" is set by default, which is the minimum needed for investigating the problem.
• A value of "1" to "180" can be set.
6.
Execute SP5-858-111 (Acquire All Info & Logs) to copy all of the log types to an SD card.
It is possible to obtain the logs separately by the following SPs.
SP
SP5-858-111
SP5-858-121
SP5-858-122
SP5-858-123
SP5-858-124
SP5-858-131
SP5-858-141
SP5-858-142
SP5-858-143
SP5-858-144
SP5-858-145
Collectable Information and/or Logs
All of the information and logs that are collected by executing the SPs from
SP5-858-121 to SP5-858-145, and SMC.
Configuration page
Font page
Print settings list
Print Error log
Fax information (whether the fax destinations are included or not depends on the setting of SP5-858-103.)
Controller log, engine log, operation panel log, FCU, and SMC.
Controller log
Engine log
Operation panel log
FCU log
723
724
5. System Maintenance
SP Collectable Information and/or Logs
SP5-992-001 SMC
7.
After executing the SP for copying the information and/or logs, a confirmation screen will appear. To proceed with obtaining the information and/or logs, tap "Execute"
• The approximate time it takes to transfer the debug log is as follows. Transfer time may be affected by the type or format of the SD card.
Controller device log (GW device log): 2 - 20 minutes
Engine device log: 2 minutes
Operation panel device log: 2 - 20 minutes
If the estimated time is not calculated due to an error, an error code will be displayed.
Error Code
-1
-2
Description
Other.
No SD card is inserted in the service slot or in the SD slot on the side of the operation panel. In this case, insert an SD card into either of the SD slots.
Error Code
-3
Capturing the Device Logs
Description
The SD card is locked. In this case, unlock the SD card, as shown below.
[A]: Unlocked, [B]: Locked
8.
Wait for the information and/or logs to be copied to the SD card.
9.
After a message stating that the process has completed appears on the operation panel, confirm that the LED light next to the SD card slot is not flashing and then remove the SD card.
10.
Make sure that the SD card access LED is off, then remove the SD card.
• The process of obtaining logs fails in the following cases:
- When the size of the logs to obtain exceeds the amount of space available on the SD card.
- When the SD card is removed while the logs are being copied to it.
- When the SD card is not formatted.
• If ‘failed’ appears on the touch panel display, turn the power off, and then recover from step
1 again.
The device logs can be retrieved via the Web Image Monitor.
725
726
5. System Maintenance
1.
Access the following URL and logon as an administrator: http://[IP address or host name]/web/entry/df/websys/direct/getSysInfo.cgi
2.
Specify the date that the problem occurred and the number of days to download the logs.
If the fax destinations need to be included in the fax information, set "On" as "Obtain Fax
Destination(s) Information". Then click "Download".
• "3" is set by default for "Number of days, including date fault occurred, to obtain". However
"2", which is the minimum needed for investigating the problems, is recommended for reducing the downloading time.
• "Obtain Fax Destination(s) Information" is set to "Off" by default.
Capturing the Device Logs
3.
The confirmation screen will appear and the information and/or logs will start downloading. To proceed to download the information and/or logs, wait for the openor-save dialog to appear.
• To cancel downloading, click "Cancel".
• To reconfigure some settings, click "Download again".
• Operation panel when downloading the logs:
4.
After a while, the open-or-save dialog will appear. Specify where to download and save the file.
• The debug logs are saved with the following file names. These names are the same as the files downloaded with SD card.
727
728
5. System Maintenance
The device logs are saved with the following file names.
Controller log (mmesg)
/LogTrace/[the model number]/watching/[yyyymmdd_hhmmss]_[a unique value].gz
Engine device log
Operation panel log
/LogTrace/[Machine Serial]/engine/[yyyymmdd_hhmmss].gz
/LogTrace/[the model number]/opepanel/
[yyyymmdd_hhmmss].tar.gz
SMC
Configuration page
/LogTrace/[the model number]/smc/[the model number]_[5992XXX]_[yyyymmdd]_[hhmmss].csv
/LogTrace/[the model number]/gps/ConfigrationPage/
ConfigrationPage_ [yyyymmdd_hhmmss].csv
Font page
Print settings list
Error log
Fax information
FCU debug log
• /LogTrace/[the model number]/gps/FontPage/
FontPage_PCL_[the page number]_[yyyymmdd_hhmmss].jpg
• /LogTrace/[the model number]/gps/FontPage/
FontPage_PDF_[the page number]_[yyyymmdd_hhmmss].jpg
• /LogTrace/[the model number]/gps/FontPage/
FontPage_PS_[the page number]_[yyyymmdd_hhmmss].jpg
• /LogTrace/[the model number]/gps/PrintSettingList/
PrintSettingList_RPGL_[yyyymmdd_hhmmss].txt
• /LogTrace/[the model number]/gps/PrintSettingList/
PrintSettingList_RTIFF_[yyyymmdd_hhmmss].csv
/LogTrace/[the model number]/gps/ErrorLog/
[yyyymmdd_hhmmss].csv
/LogTrace/[the model number]/faxreport/[yyyymmdd_hhmmss].csv
/LogTrace/[Machine Serial]/fculog/[yyyymmdd_hhmmss].gz
SMC List Card Save Function
The SMC List Card Save (SP Text Mode) function is used to save the SMC list as CSV files to the SD-card inserted into the operation panel SD-card slot.
• Make sure to shut down and reboot the machine once before exporting the SMC sheet data.
Otherwise, the latest settings may not be collected when the SMC is exported.
1.
Turn OFF the main power.
2.
Insert the SD card into the operation panel SD-card slot, and then turn OFF the main power.
3.
Enter SP mode.
4.
Select "System SP".
5.
Select SP5-992-001 (SP Text Mode).
6.
Select a detail SP number shown below to save data on the SD card.
SP5-992-xxx (SP Text Mode)
729
730
5. System Maintenance
Detail No.
SMC Categories to Save
001 All (Data List)
002 SP (Mode Data List)
003 User Program
004 Logging Data
005 Diagnostic Report
006 Non-Default
007 NIB Summary
008 Capture Log
021 Copier User Program
022 Scanner SP
023 Scanner User Program
024 SDK/J Summary
025 SDK/J Application Info
026 Printer SP
027 Smart Operation Panel SP
028 Smart Operation Panel UP
7.
Press [EXECUTE].
8.
Press [EXECUTE] again to start. Press [CANCEL] to cancel the saving.
SMC List Card Save Function
9.
"It is executing it" is shown on the screen while executing.
10.
Wait for 2 to 3 minutes until "Completed" is shown.
• The SMC list saving may take from 2 to 3 minutes to complete.
• Press [CANCEL] to abort executing.
11.
Press [Exit] to exit from SP mode.
The SMC list data saved on the SD-card will be named automatically. The file naming rules are as follows.
Example:
731
5. System Maintenance
732
A:
Machine serial number (fixed for each machine)
B:
SP number saved in this file.
First four digits (5992) in this part are fixed. The other one or two digits are the detail SP number(s). In this case, it is one digit. Therefore, this file is of SP5-992-001 (All data list). See the upper SP table for the correspondence between SP detail numbers and the contents.
C:
File creation date
Year/Month/Day ("Zero" will be omitted if each is one digit.)
D:
File creation time
Hour/Minute/Second ("Zero" will be omitted if each is one digit.)
E:
File Extension CSV (Comma Separated Value)
This part is fixed.
• A folder named by the machine serial number will be created on the SD card when this function is executed.
• This function can save the SMC list data only to an SD card inserted into the operation panel SD card slot.
SMC List Card Save error message:
• Failed:
FACTOR: Read-only file system, No space left on device.
If an error occurs, pressing "Exit" will cause the device to discard the job and return to the ready state.
UP/SP Data Import/Export
• Copier / Document Server Features
• Printer Features
• Scanner Features
• Facsimile Features
• Browser Features
• Extended Feature Settings
• Program (Document Server)
• Program (Copier)
• Program (Scanner)
• Web Image Monitor Setting
• Web Service Settings
• System Settings
• Some System Settings *1 *2
*1 The setting for the date, settings that require the device certificate, and settings that need to be adjusted for each machine (for example, image adjustment settings) cannot be imported or exported.
*2 Settings only for executing functions and settings only for viewing cannot be imported or exported.
• Extended Feature Settings
• Address book
• Programs (fax function)
• Programs (printer function)
• User stamp in Copier / Document Server Features
• Settings that can be specified via telnet
• @Remote-related data
733
734
5. System Maintenance
• Counters
• EFI printer unit settings
• Settings that can only be specified via Web Image Monitor or Web Service (for example, Bonjour,
SSDP setting)
This can be exported / imported by an administrator with all privileges.
When exporting SP device information from the control panel, the data is saved on an SD card.
1.
Insert an SD card into the media slot on the side of the control panel.
2.
Log in from the control panel as an administrator with all privileges.
3.
Press [User Tools] icon > [Machine Features] > [System Settings].
4.
Press [Administrator Tools].
5.
Press [Device Setting Information: Export (Memry Strge Devc)].
UP/SP Data Import/Export
6.
Set the export conditions.
• Specify whether to [Include] or [Exclude] the "Device Unique Information". "Device Unique
Information" includes the IP address, host name, fax number, etc.
• Specify an encryption key.
7.
Press [Run Export].
8.
Press [OK].
9.
Press [Exit].
10.
Log out.
• If data export fails, the details of the error can be viewed in the log.
• When device Information is periodically imported, it is necessary to create the device setting information file with special software and store it on the web server.
This can be exported / imported by an administrator with all privileges.
Import device information saved on an SD card.
1.
Insert an SD card into the media slot on the side of the control panel.
2.
Log in from the control panel as an administrator with all privileges.
3.
Press [User Tools] icon > [Machine Features] > [System Settings].
4.
Press [Administrator Tools].
5.
Press [Device Setting Information: Import (Memry Strge Devc)].
735
5. System Maintenance
6.
Configure the import conditions.
736
• Press [Select] of the "Device Setting Info. File" to select the file(s) to import.
• When inserting a file into a home screen, press [Select] for the Image for Home screen and select the file. You cannot use this setting when using the Smart Operation Panel.
• Specify whether to [Include] or [Exclude] the "Device Unique Information". "Device Unique
Information" includes the IP address, host name, fax number, etc.
• Enter the encryption key that was specified when the file was exported.
7.
Press [Run Import].
8.
Press [OK].
9.
Press [Exit].
The machine restarts.
• If data export fails, the details of the error can be viewed in the log.
• System SP
• Printer SP
• Fax SP
• Scanner SP
UP/SP Data Import/Export
When exporting SP device information from the control panel, the data is saved on an SD card.
1.
Insert an SD card into the media slot on the side of the control panel.
2.
Enter SP mode.
3.
Press SP5-749-001 (Import/Export: Export)
4.
Select "Target" SP settings (System/Printer/Fax/Scanner/Smart Operation Panel) to be exported.
5.
Select "Option" settings (Unique/Secret).
Item
Unique
Specification
Unique information of the machine is included in the exported file if you select "Unique" setting.
Note
Unique information that can be updated
#1. Items that are to be used to identify the machine.
Example: Network Information/ Host name / Information related to fax number /Mail address assigned to the machine
#2. Items for specifying the options equipped on the machine.
Example: Lot number for developer
Unique information that cannot be updated
#1. Items that may cause a problem if imported
Example: Serial number / Information related to @Remote
#2. Items for managing the history of the machine
Example: Time and date / Counter information /
Installation date
#3. Setting values for the Engine
737
738
5. System Maintenance
Item
Secret
Specification
Secret information is exported if you select "Secret" setting.
Note
Secret information
#1. Data that cannot be exported without being encrypted.
(Exported data is encrypted.)
Example: Password / Encryption key / PIN code
#2. Confidential information for the customer
Example: User name / User ID / Department code / Mail address / Phone number
#3. Personal information
Example: Document name / Image data
#4. Sensitive information for the customer
Example: MAC address / Network parameters
* The IP address is exported when both 'Unique' and 'Secret' are selected.
6.
Select "Crpt config" setting (Encryption).
Encryption Select whether to encrypt or not when exporting.
If you push the
"Encryption" key, you can export secret information.
If the encryption function is used, setting of an encryption key is required by direct input.
• Type the arbitrary password using the soft keyboard
• Can enter up to 32 characters
7.
Press [Execute].
8.
Press [OK].
• If data export fails, the details of the error can be viewed in the log.
Import device information saved on an SD card.
1.
Insert an SD card into the media slot on the side of the control panel.
2.
Enter SP mode.
3.
Press SP5-749-101(Import/Export: Import)
4.
Select a unique setting.
5.
Press [Encryption Key], if the encryption key was created when the file was exported.
UP/SP Data Import/Export
6.
Select an encryption setting.
Unique
Encryption
7.
Press [Execute].
8.
Press [OK].
If you want to apply the unique information to the target machine, select the "Unique" key.
If an encrypted file is selected as the import file, this setting is required.
Refer to the above information.
• If data export fails, the details of the error can be viewed in the log.
The access log file is created when export/import is executed. The file is stored in the same location as the exported device setting information file.
If an error occurs, check the log's result code in the access log file first. Values other than 0 indicate that an error occurred.
The result code will appear in the circled area illustrated below.
- Example of a log file
If you cannot solve the problem or do not know how to solve it after checking the code, note down the error log entry, then contact your supervisor.
739
740
5. System Maintenance
Result Code
2 (INVALID REQUEST)
4 (INVALID OUTPUT
DIR)
7( MODULE ERROR)
8 (DISK FULL)
9 (DEVICE ERROR)
10 (LOG ERROR)
Cause
A file import was attempted between different models or machines with different device configurations.
Failed to write the device information to the destination device.
Solutions
Import files exported from the same model with the same device configurations.
Check whether the destination device is operating normally.
An unexpected error occurred during import or export.
Switch the power off and then back on, and then try the operation again. If the error persists, contact your supervisor.
The available storage space on the external medium is insufficient.
Execute the operation again after making sure there is enough storage space.
Failed to write or read the log file.
Check whether the path to the folder for storing the file or the folder in which the file is stored is missing.
The hard disk is faulty.
Contact your supervisor.
UP/SP Data Import/Export
Result Code
20 (PART FAILED)
21 (INVALID FILE)
22 (INVALID KEY)
Failed to import some settings.
Cause
Failed to import the file because it is in the wrong format in the external medium.
The encryption key is not valid.
Solutions
The reason for the failure is logged in
"NgCode". Check the code.
Reason for the Error (Ng-Name)
2. INVALID VALUE
The specified value exceeds the allowable range.
3. PERMISSION ERROR
The permission to edit the setting is missing.
4. NOT EXIST
The setting does not exist in the system.
5. INTERLOCK ERROR
The setting cannot be changed because of the system status or interlocking with other specified settings.
6. OTHER ERROR
The setting cannot be changed for some other reason.
Check whether the file format is correct.
The import file should be a CSV file.
Use the correct encryption key.
• When exporting device information from the control panel, the data can be saved only on an SD card.
• The file format for exports is CSV.
741
742
5. System Maintenance
• The Card Save function is used to save print jobs received by the printer on an SD card with no print output. Card Save mode is toggled using printer Bit Switch #1 bit number 4. Card Save will remain enabled until the SD card becomes full, or until all file names have been used.
• Captures are stored on the SD card in the folder /prt/cardsave. File names are assigned sequentially from PRT00000.prn to PRT99999.prn. An additional file PRT.CTL will be created. This file contains a list of all files created on the card by the card save function.
• Previously stored files on the SD card can be overwritten or left intact. Card Save SD has "Add" and "New" menu items.
• Card Save (Add): Appends files to the SD Card. Does not overwrite existing files. If the card becomes full or if all file names are used, an error will be displayed on the operation panel.
Subsequent jobs will not be stored.
• Card Save (New): Overwrites files in the card's /prt/cardsave directory.
Limitation:
• Card Save cannot be used with PJL Status Readback commands. PJL Status Readbacks will not work. In addition they will cause the Card Save to fail.
1.
Turn OFF the main power.
2.
Insert the SD card into slot 2 (lower), then turn ON the main power.
3.
Enter SP mode.
4.
Select the "Printer SP".
Card Save Function
5.
Select SP-1001 "Bit Switch".
6.
Select "Bit Switch 1 Settings" and use the numeric keypad to turn bit 4 ON and then press the "#" to register the change. The result should look like: 00010000. By doing this, Card
Save option will appear in the "List/Test Print" menu.
7.
Press "Exit" to exit SP Mode.
8.
Press the "User Tools" icon > "Machine Features".
9.
Select "Printer Features".
743
5. System Maintenance
10.
Card Save (Add) and Card Save (New) should be displayed on the screen. Select Card
Save (Add) or Card Save (New).
744
11.
Press "OK" and then return to Home screen.
12.
Press the "Printer (Classic)" icon.
13.
"Hex Dump Mode" is be displayed in the top left of the display panel.
Card Save Function
14.
Send a job to the printer. The Communicating light should start blinking.
15.
As soon as the printer receives the data, it will be stored on the SD card automatically with no print output.
Nothing is displayed on the screen, indicating that a Card Save operation was successful.
16.
Press "Reset" to exit Card Save mode.
17.
Change the Bit Switch Settings back to the default 00000000, then press the "#" in the numeric keypad to register the changes.
18.
Remove the SD card after the main power switch is turned OFF.
Card Save error messages:
• Init error: A card save process (e.g. card detection, change to kernel mode) failed to initialize.
745
746
5. System Maintenance
• Card not found: Card cannot be detected in the slot.
• No memory: Insufficient working memory to process the job.
• Write error: Failed to write to the card.
• Other error: An unknown error occurred.
If an error occurs, pressing "OK" will cause the device to discard the job and return to the ready state.
When an ordinary SC (pattern D) is generated, automatically reboot is performed. Automatic reboot or reboot by user operation can be set by SP5-875-001 (SC automatic reboot setting out) (default value:
0 "Automatic reboot").
When a type D occurs, automatic reboot is done or the machine display asks the customer if it can reboot. However, when the SC occurs twice in a short time, the machine sends a report to the @Remote server without rebooting. This is because just rebooting may not be a good solution if an SC occurs twice.
When an automatic reboot is performed, a confirmation screen is displayed after reboot. The confirmation screen can be cancelled by pressing the [OK] key (display is not cancelled only when the main power switch is switched OFF to ON).
Screen display during reboot
• Status display on the current screen
• Post-processing ...... Post-processing during printing, etc.
• Automatic reboot .... After operation end
Post-processing
Until automatic reboot
• Reset key (Reboot key)
Key to perform reboot
# Cancel key is not displayed.
• Turn on spanner LED (same as when an SC is generated).
Operation during SC reboot
• Timing of SC reboot
When @Remote is enabled, and when a NRS alarm*1 is not generated, the corresponding
SC is the object of an automatic reboot.
*1 NRS alarm: Issued when an ordinary SC (type D) is generated twice while the total counter counts
10 times.
747
748
6. Troubleshooting
• Time to automatic reboot
Reboot is performed 30 seconds after an engine reboot is possible, after the end of postprocessing during printing, etc.
At that time, a reboot is performed even if the MFP is operating. The engine does not start process control when a reboot is possible.
• Automatic reboot
See the flowchart below.
Self-Diagnostic Mode
749
750
6. Troubleshooting
• For the SC list of automatic reboot, refer to page 757 "List of Automatic Reboot Target SC".
Controller self-diagnosis includes 3 types, i.e., "ordinary self-diagnosis", "detailed self-diagnosis", and
"SC detection". "Ordinary self-diagnosis" is diagnosis performed for every power ON, and "detailed self-diagnosis" is diagnosis treated as part of the service tools. "SC detection" detects mechanical faults when power is switched on or when the machine is operating.
Detailed self-diagnosis – Method
1. After attaching the option "IEEE 1284 board" to the controller board, connect the provided conversion connector.
2. Set a loop back connector in the reference Centronics I/F.
3. Press the main power supply switch while simultaneously pressing the "#" and "./* key. The display changes to the following screen, and self-diagnosis starts.
4. After the end of detailed self-diagnosis, a "Self-diagnosis results report" is automatically printed.
• If a Centronics loopback connector is not fitted, a Centronics diagnosis error (SC 835) is generated.
Self-Diagnostic Mode
751
752
6. Troubleshooting
Self-Diagnostic Mode
753
6. Troubleshooting
754
When an error occurs to the HDD, the HDD abnormality message appears on the operation panel and the screen for formatting is displayed. Also when replacing the HDD, a message "Hard Disk is replaced." appears on the operation panel and the screen for formatting is displayed.
Refer to the table shown below for the conditions of the message display.
Even when replacing the controller board, a banner "Hard Disk is replaced." appears. It is because the machine recognizes HDD has been replaced when the controller board that does not hold the HDD identification information is attached.
Message list
Message
Display
Type
Normal/
Abnormal
Error Condition/ Major Cause/ Solution
SC870 banner abnormal
The HDD cannot be accessed at poweron.
NVRAM defective
Turn the main power off/on to initialize the machine.
*When replacing the NVRAM, if possible, back up the address book before replacing the NVRAM and restore it after replacing the NVRAM.
Self-Diagnostic Mode
Hard Disk.
Message
Hard Disk will be formatted due to problem with Hard Disk.
Problem with the Encryption Key for Hard Disk. Format Hard
Disk.
Hard Disk is replaced. Format
Hard Disk is replaced.
Formatting Hard Disk... Please wait, also make sure the main power switch is not turned off.
Hard Disk is formatted. Turn main power switch off then on.
Display
Type pop-up formatting button pop-up formatting button pop-up formatting button banner pop-up pop-up
Normal/
Abnormal
Error Condition/ Major Cause/ Solution abnormal abnormal normal abnormal abnormal abnormal
Management file on the HDD can not be read. Or the file system can not be mounted.
HDD defective
Replace the HDD.
The encryption key for the HDD is abnormal.
HDD defective
Replace the HDD.
A new HDD is attached.
A new HDD attached
Push the formatting button.
The HDD is replaced (Data can be read).
• Controller board replaced
• After starting the machine without an HDD, a new HDD is attached to the machine and then restart the machine.
Turn the main power off/on.
Pushing the formatting button.
-
Formatting the HDD
Formatting the HDD is finished.
Formatting the HDD
Turn the main power off/on.
755
756
6. Troubleshooting
The ‘SC Table’ section shows the SC codes for controller errors and other errors. The latter are put into four types. The type is determined by their reset procedures. The table shows the classification of the SC codes.
Type
A
B
C
D
Display
Turn the operation switch off and on.
How to reset
The SC is immediately displayed on the operation panel when SC occurs.
The error involves the fusing unit. The machine operation is disabled. The user cannot reset the error.
• When canceling a fusing unit SC, (SC544-00/
SC554-00/ SC564-00/ SC574-00), perform part replacement in accordance with the above procedure.
Reset the SC (set SP5-810-1) and then cycle the main power off and on.
When a function is selected, the SC is displayed on the operation panel.
The machine cannot be used (down-time mitigation).
No display on the operation panel.
The machine operates as usual.
The SC is displayed on the operation panel.
The machine cannot be used (machine-error SC).
Only the SC history is updated.
Turn the main n power switch off and on.
• When an ordinary SC (type D) is generated, an automatic reboot is performed. When an event is reported by the customer support system, even in the event of an ordinary SC, reboot is not performed. During automatic reboot, a confirmation screen is displayed after the reboot.
• When automatic reboot occurs twice continuously, an SC is displayed without rebooting, and logging count is performed. Also, when an SMC print is output, an * mark is added alongside the
SC number for clarity.
• Automatic reboot can be enabled or disabled with SP5-875-001 (SC automatic reboot setting)
(default value: ON).
Service Call Conditions
SP descriptions
• SP5-875-001 (SC automatic reboot: Reboot Setting)
Enables or disables the automatic reboot function when an SC error occurs.
0: The machine reboots automatically when the machine issues an SC error and logs the SC error code. If the same SC occurs again, the machine does not reboot.
1: The machine does not reboot when an SC error occurs.
The reboot is not executed for the pattern A or C.
When an SC is generated, the "total count value when the SC is generated" and the "SC code" are logged. However, if the total count value during the SC is the same as last time, logging is not performed.
Logged data can be checked by outputting an administrative report (SMC print). The SC history is logged up to the last 10 entries, and if there are more than 10 entries, data are progressively deleted starting from the oldest.
Automatic reboot target SC is as follows. For details of Automatic reboot, refer to page 747 "SC
SC code
101-01
101-02
102-00
120-00
121-00
141-00
142-00
144-00
Name
Lamp Error (Scanning)
Lamp Error (LED illumination adjustment)
LED Illumination Adjustment Error
Scanner Home Position Error 1
Scanner Home Position Error 2
Black level detection error
White level detection error
SBU Communication Error
757
758
6. Troubleshooting
203-00
204-00
220-01
220-04
230-01
230-02
230-03
230-04
SC code
151-00
152-00
154-00
161-02
161-20
202-00
231-01
231-02
231-03
231-04
240-01
240-02
240-03
240-04
272-01
272-02
272-03
Name
Black Level Error: Side 2
White Level Error: Side 2
Scanner Communication Error: Side 2
IPU error (Lsync Error: Side 2)
IPU error (DRAM initialization failure)
Polygon Motor: ON Timeout Error
Polygon Motor: OFF Timeout Error
Polygon Motor: XSCRDY Signal Error
Leading Edge: LD1 synchronization detection error: Bk
Leading Edge: LD1 synchronization detection error: Ye
FGATE ON error: Bk
FGATE ON error: Cy
FGATE ON error: Ma
FGATE ON error: Ye
FGATE OFF error: Bk
FGATE OFF error: Cy
FGATE OFF error: Ma
FGATE OFF error: Ye
LD error: Bk
LD error: Cy
LD error: Ma
LD error: Ye
LD driver communication error: Bk
LD driver communication error: Cy
LD driver communication error: Ma
324-05
360-01
360-02
360-03
360-04
396-05
441-00
442-00
SC code
272-04
272-10
312-01
312-02
312-03
312-04
452-00
491-00
531-01
531-03
533-03
533-04
534-01
534-02
534-03
535-00
540-00
Name
LD driver communication error: Ye
LD driver communication error: Other
Charge Roller HVP_CB Output Error (K)
Charge Roller HVP_CB Output Error (C)
Charge Roller HVP_CB Output Error (M)
Charge Roller HVP_CB Output Error (Y)
Development motor: CMY: Lock
TD sensor adjustment error (K)
TD sensor adjustment error (C)
TD sensor adjustment error (M)
TD sensor adjustment error (Y)
Drum motor (CMY) Lock
Drum transfer motor: Lock
ITB Lift Error
Paper transfer contact motor error
High voltage power source: charge/development: output error
Development Intake Fan/Right Lock
Drive Cooling Fan Lock
PSU Cooling Fan Lock
Controller Box Cooling Fan Lock
Main Exhaust Fan Lock
Toner Supply Cooling Fan Lock
Ozone Exhaust Fan Lock
Paper Exit Cooling Fan Lock
Fusing Motor: Lock
Service Call Conditions
759
760
6. Troubleshooting
552-05
552-06
561-05
562-05
569-00
571-05
572-05
581-05
SC code
542-05
542-06
545-05
547-01
547-02
547-03
582-05
620-01
620-02
620-03
621-00
622-01
622-11
663-01
663-02
663-03
663-11
Name
Thermopile (Center) does not reload (Low Power)
Thermopile (Center) does not reload (Low Power)
Fusing Central Lamp Continuously Heat (Low Power)
Zero cross error (relay-contact soldering)
Zero cross error (relay contact error)
Zero cross error (low-frequency error)
Thermopile (Center) Does Not Reload (Low Power)
Thermopile (Center) Does Not Reload (Low Power)
Pressure Roller Thermistor (Center) Disconnection (Low Power)
Pressure Roller Thermistor (Center) Does Not Reload (Low Power)
Paper Exit/ Pressure Release Motor Error Detection
Pressure Roller Thermistor (Edge) Disconnection
Pressure Roller Thermistor (Edge) Does Not Reload ( Low Power)
Pressure Roller Thermistor (Full-Bleed Edge) Disconnection (Low Power)
Pressure Roller Thermistor (Full-Bleed Edge) Does Not Reload (Low Power)
ADF Communication error 1
ADF Communication error 2
ADF Communication error 3
Finisher communication error
Paper bank 1 communication error for Paper Feed Unit PB3150 (D694)
Paper bank 1 communication error for Paper Feed Unit PB3220/PB3210 (D787)
Reset Detection: Imaging IOB: Software hangup occurs
Reset Detection: Imaging IOB: Power ON reset occurs
Reset Detection: Imaging IOB: Software reset occurs
Reset Detection: Paper Transport IOB: Software hangup occurs
Service Call Conditions
669-04
669-05
669-06
669-07
669-08
669-09
669-10
669-11
SC code
663-12
663-13
664-01
669-01
669-02
669-03
669-12
669-13
669-14
669-15
669-16
669-17
669-18
669-19
669-20
669-21
669-22
Name
Reset Detection: Paper Transport IOB: Power ON reset occurs
Reset Detection: Paper Transport IOB: Software reset occurs
VODKA1 (Paper Transport Vodka) access permission error to VODKA SRAM
EEPROM OPEN: ID error
EEPROM OPEN: Channel error
EEPROM OPEN: Device error
EEPROM OPEN: Communication abort error
EEPROM OPEN: Communication timeout error
EEPROM OPEN: Operation stopped error
EEPROM OPEN: Buffer full
EEPROM OPEN: No error code
EEPROM CLOSE: ID error
EEPROM CLOSE: No error code
EEPROM Data write: ID error
EEPROM Data write: Channel error
EEPROM Data write: Device error
EEPROM Data write: Communication abort error
EEPROM Data write: Communication timeout error
EEPROM Data write: Operation stopped error
EEPROM Data write: Buffer full
EEPROM Data write: No error code
EEPROM Data read: ID error
EEPROM Data read: Channel error
EEPROM Data read: Device error
EEPROM Data read: Communication abort error
761
762
6. Troubleshooting
681-01
681-02
681-03
681-04
681-06
681-07
681-08
681-09
SC code
669-23
669-24
669-25
669-26
669-36
669-37
681-11
681-12
681-13
681-14
681-16
681-17
681-18
681-19
681-21
681-22
681-23
Name
EEPROM Data read: Communication timeout error
EEPROM Data read: Operation stopped error
EEPROM Data read: Buffer full
EEPROM Data read: No error code
Verification error
Error Detection
Toner bottle: IDChip Communication error: Invalid device ID :K
Toner bottle: IDChip Communication error: Invalid device ID :M
Toner bottle: IDChip Communication error: Invalid device ID :C
Toner bottle: IDChip Communication error: Invalid device ID :Y
Toner bottle: IDChip Communication error: Channel error :K
Toner bottle: IDChip Communication error: Channel error :M
Toner bottle: IDChip Communication error: Channel error :C
Toner bottle: IDChip Communication error: Channel error :Y
Toner bottle: IDChip Communication error: Device Error :K
Toner bottle: IDChip Communication error: Device Error :M
Toner bottle: IDChip Communication error: Device Error :C
Toner bottle: IDChip Communication error: Device Error :Y
Toner bottle: IDChip Communication error: Communication error (interrupted) :K
Toner bottle: IDChip Communication error: Communication error (interrupted) :M
Toner bottle: IDChip Communication error: Communication error (interrupted) :C
Toner bottle: IDChip Communication error: Communication error (interrupted) :Y
Toner bottle: IDChip Communication error: Communication timeout :K
Toner bottle: IDChip Communication error: Communication timeout :M
Toner bottle: IDChip Communication error: Communication timeout :C
Service Call Conditions
681-32
681-33
681-34
681-36
681-37
681-38
681-39
682-01
SC code
681-24
681-26
681-27
681-28
681-29
681-31
682-02
682-03
682-04
682-06
682-07
682-08
682-09
682-11
682-12
682-13
682-14
Name
Toner bottle: IDChip Communication error: Communication timeout :Y
Toner bottle: IDChip Communication error: Device stops (logically) :K
Toner bottle: IDChip Communication error: Device stops (logically) :M
Toner bottle: IDChip Communication error: Device stops (logically) :C
Toner bottle: IDChip Communication error: Device stops (logically) :Y
Toner bottle: IDChip Communication error: Full of buffer (request) :K
Toner bottle: IDChip Communication error: Full of buffer (request) :M
Toner bottle: IDChip Communication error: Full of buffer (request) :C
Toner bottle: IDChip Communication error: Full of buffer (request) :Y
Toner bottle: IDChip Communication error: Verification error:K
Toner bottle: IDChip Communication error: Verification error:M
Toner bottle: IDChip Communication error: Verification error:C
Toner bottle: IDChip Communication error: Verification error:Y
TD sensor communication error: Invalid device ID :K
TD sensor communication error: Invalid device ID :M
TD sensor communication error: Invalid device ID :C
TD sensor communication error: Invalid device ID :Y
TD sensor communication error: Channel error :K
TD sensor communication error: Channel error :M
TD sensor communication error: Channel error :C
TD sensor communication error: Channel error :Y
TD sensor communication error: Device Error :K
TD sensor communication error: Device Error :M
TD sensor communication error: Device Error :C
TD sensor communication error: Device Error :Y
763
764
6. Troubleshooting
682-23
682-24
682-26
682-27
682-28
682-29
682-31
682-32
SC code
682-16
682-17
682-18
682-19
682-21
682-22
682-33
682-34
682-36
682-37
682-38
682-39
687-00
700-01
700-02
700-04
700-05
Name
TD sensor communication error: Communication error (interrupted) :K
TD sensor communication error: Communication error (interrupted) :M
TD sensor communication error: Communication error (interrupted) :C
TD sensor communication error: Communication error (interrupted) :Y
TD sensor communication error: Communication timeout :K
TD sensor communication error: Communication timeout :M
TD sensor communication error: Communication timeout :C
TD sensor communication error: Communication timeout :Y
TD sensor communication error: Device stops (logically) :K
TD sensor communication error: Device stops (logically) :M
TD sensor communication error: Device stops (logically) :C
TD sensor communication error: Device stops (logically) :Y
TD sensor communication error: Full of buffer (request) :K
TD sensor communication error: Full of buffer (request) :M
TD sensor communication error: Full of buffer (request) :C
TD sensor communication error: Full of buffer (request) :Y
TD sensor communication error: Verification error:K
TD sensor communication error: Verification error:M
TD sensor communication error: Verification error:C
TD sensor communication error: Verification error:Y
PER Not Received Error
SPDF: Base Plate Lift Motor Error
SPDF: Original Pick-up Error
SPDF: Paper Feed Motor Error
SPDF: Pullout Motor Error
Service Call Conditions
702-02
702-03
702-04
702-05
780-01
781-01
791-00
995-01
SC code
700-06
700-07
700-09
701-03
701-08
702-01
995-02
995-03
995-04
Name
SPDF: Intermediate Motor Error
SPDF: Scanning Motor Error
SPDF: Paper Exit Motor Error
SPDF: Paper Feed Motor Driver Error
SPDF: Paper Exit Motor Driver Error
ARDF: Protection Device Intercept Error 1
ARDF: Protection Device Intercept Error 2
ARDF: Protection Device Intercept Error 3
SPDF: Protection Device Intercept Error 4
SPDF: Protection Device Intercept Error 5
Bank 1 (Upper optional paper tray) Protection Device Intercept Error
Bank 2 (Lower optional paper tray) Protection Device Intercept Error
No bridge unit when finisher is present
CPM setting error 1
CPM setting error 2
CPM setting error 3
CPM setting error 4
Automatic reboot target SC is as follows. For details of Automatic reboot, refer to page 747 "SC
Name SC code
632-00
633-00
634-00
Counter device error 1
Counter device error 2
Counter device error 3
765
766
6. Troubleshooting
641-01
641-02
641-03
641-04
670-01
670-02
670-03
670-04
SC code
635-00
636-01
636-02
637-01
637-02
641-00
816-00
816-01
816-02
816-03
816-04
Counter device error 4
IC Card Error (Expanded authentication module error)
IC Card Error (Version error)
Tracking Information Notification Error (Tracking application error)
Tracking Information Notification Error (Management server error)
Communication error between BCU and Controller board
Communication error between BCU and Controller board: Timout
Communication error between BCU and Controller board: retry over
Communication error between BCU and Controller board: download error
Communication error between BCU and Controller board: UART error
Engine does not start up during the staring up
Engine does not start up after the staring up
IPU power does not start up
Communication is not linked up
Energy save I/O subsystem error
Subsystem error
Sysarch (LPUX_GET_PORT_INFO) error
Transition to STR was denied.
Interrupt in kernel communication driver
Name
816-05
816-07
816-08
816-09
Preparation for transition to STR failed.
Sysarch (LPUX_GET_PORT_INFO) error
Sysarch (LPUX_ENGINE_TIMERCTRL) error
Sysarch (LPUX_RETURN_FACTOR_STR) error
816-10 to 12 Sysarch (LPUX_GET_PORT_INFO) error
816-13 open() error
816-24
816-25
816-26
816-27
816-28
816-29
816-30
816-35
SC code
816-14 Memory address error
816-15 to 18 open() error
816-19
816-20
816-22
816-23
Double open() error open() error
Parameter error read() error read() error write () error write() communication retry error write() communication retry error write() communication retry error read() communication retry error read() communication retry error read() error
816-36 to 94 Subsystem error
818-00 Watchdog timer error
821-00
823-00
827-00
Self-diagnostics error: ASIC
Self-diagnostics error: NIC
Self-diagnostics error: RAM
828-00
829-00
833-00
839-00
840-00
841-00
Self-diagnostics error: ROM
Self-diagnostics error: Optional Serial
Self-diagnostic error: Engine I/F ASIC
Self-diagnostic Error: Serial Flash
EEPROM access error
EEPROM read data error
Name
Service Call Conditions
767
768
6. Troubleshooting
SC code
850-00
862-00
Name
Network I/F Error
Number of the defective sector reaches the maximum count
863-00 to 23 HDD data read failure
864-00 to 23 HD data CRC error
865-00 to 23 HDD access error
865-50 to 73 HDD time-out error
868-00 to 02 SD card authentication error
871-01 FCU error
875-01
875-02
Delete all error (HDD erasure) (hddchack –i error)
Delete all error (HDD erasure) (Data deletion failure)
875-03
880-00
899-00
919-00
Delete all error (HDD erasure)
MLB error
Software performance error (signal reception end)
External controller down
990-00
992-00
997-00
998-00
Software operation error
Undefined SC issued.
Application function selection error
Application start error
The table shows the classification of the SC codes:
Class
SC1xx
SC2xx
Scanning
Exposure
Section
Class
SC3xx
SC4xx
SC5xx
SC6xx
SC7xx
SC8xx
SC9xx
Section
Image Processing 1
Image Processing 2
Paper feed and Fusing
Communication
Peripherals
Overall System
Others
Service Call Conditions
769
770
6. Troubleshooting
SC No.
SC101-01
Type
D
Error Name/Error Condition/Major Cause/Solution
LED Error (Scanning)
The white level peak did not reach the prescribed threshold when the white guide plate was scanned.
• Scanner Carriage defective
• BCU defective
• Connector defective (disconnected, loose)
• Harness defective
• IPU defective
• Condensation in scanner unit
• White Reference Seal dirty or installed incorrectly (sheet-through exposure glass)
• White Guide Plate, or White Roller dirty or installed incorrectly
(SPDF/ARDF)
Service Call 101-195
SC No.
SC101-02
Type
D
Error Name/Error Condition/Major Cause/Solution
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Clean the white guide plate, or white roller (SPDF/ARDF).
2. Reconnect the following connectors;
• Scanner Carriage - IPU harness (FFC)
• SBU - LEDB harness (FFC)
• IPU- BCU harness
3. Check the white reference seal that attached back of sheet-through exposure glass. Replace the sheet-through exposure glass, if dirty or damaged.
4. Replace the white guide plate, or white roller (SPDF/ARDF).
5. Replace the Scanner Carriage.
6. Replace the IPU.
7. Replace the following harnesses;
• Scanner Carriage - IPU harness (FFC)
• IPU - BCU harness
8. Replace the BCU.
LED Error (LED illumination adjustment)
LED error was detected.
• Connector defective (disconnected, loose)
• Scanner Carriage defective
• IPU defective
• Harness defective
• BCU defective
771
772
6. Troubleshooting
SC No.
Type Error Name/Error Condition/Major Cause/Solution
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Reconnect the following connectors;
• Scanner Carriage - IPU harness (FFC)
• SBU - LEDB harness (FFC)
• IPU- BCU harness
2. Check the white reference seal that attached back of sheet-through exposure glass. Replace the sheet-through exposure glass, if dirty or damaged.
3. Replace the Scanner Carriage.
4. Replace the IPU.
5. Replace the following harnesses;
• Scanner Carriage - IPU harness (FFC)
• IPU - BCU harness
6. Replace the BCU.
Service Call 101-195
SC No.
SC102-00
Type
D
Error Name/Error Condition/Major Cause/Solution
LED Illumination Adjustment Error
The white level peak reached the prescribed threshold when the white plate was scanned after a specified number of adjustments.
• LED defective
• IDB (LED driver) defective
• SBU defective
• IPU defective
• Power/signal harness defective
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Reconnect the power/signal harness.
2. Replace the following parts:
• Replace the Scanner Carriage.
• Replace the IPU board.
• Replace the power/signal harness.
773
774
6. Troubleshooting
SC No.
SC120-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Scanner Home Position Error 1
The scanner home position sensor does not go OFF.
Details:
Error detection timing
• During homing (when the machine is turned ON or when it returns from energy save mode)
• During an automatic adjustment (when the machine is turned ON or when it returns from energy save mode)
• During a scan from the ADF/ARDF or exposure glass.
• Scanner motor driver defective
• Scanner motor defective
• Scanner HP sensor defective
• Harness defective
• Timing belt, pulley, wire, or carriage not installed correctly
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps.
1. Replace the following parts:
• Replace the HP sensor
• Replace the scanner motor
• Replace the harness.
Service Call 101-195
SC121
RTB 23
SC No.
SC121-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Scanner Home Position Error 2
The scanner home position sensor does not go ON.
Details:
Error detection timing
• During homing
• During an automatic adjustment
• During a scan from the ADF/ARDF or exposure glass.
• Scanner motor driver defective
• Scanner motor defective
• Scanner HP sensor defective
• Harness defective
• Timing belt, pulley, wire, or carriage not installed correctly
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps.
1. Replace the following parts:
• Replace the home position sensor
• Replace the scanner motor
• Replace the harness.
775
776
6. Troubleshooting
SC No.
SC141-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Black level detection error
The black level cannot be adjusted within the target during auto gain control.
• Scanner Carriage defective
• IPU defective
• Harness defective
• BCU defective
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Reconnect the following connectors;
• Scanner Carriage - IPU harness (FFC)
• IPU- BCU harness
2. Replace the Scanner Carriage.
3. Replace the IPU.
4. Replace the following harnesses;
• Scanner Carriage - IPU harness (FFC)
• IPU - BCU harness
5. Replace the BCU.
Service Call 101-195
SC No.
SC142-00
Type
D
Error Name/Error Condition/Major Cause/Solution
White level detection error
The white level cannot be adjusted to the second target level within the target during auto gain control.
• Scanner Carriage defective
• IPU defective
• Harness defective
• Connector defective (disconnected, loose)
• Condensation in scanner unit
• White plate dirty or installed incorrectly
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Reconnect the following connectors;
• Scanner Carriage - IPU harness (FFC)
• SBU - LEDB harness (FFC)
• IPU- BCU harness
2. Check the white reference seal that attached back of sheet-through exposure glass. Replace the sheet-through exposure glass, if dirty or damaged.
3. Replace the scanner carriage.
4. Replace the IPU.
5. Replace the following harnesses;
• Scanner Carriage - IPU harness (FFC)
• IPU - BCU harness
6. Replace the BCU.
777
778
6. Troubleshooting
SC No.
SC144-00
Type
D
Error Name/Error Condition/Major Cause/Solution
SBU Communication Error
• The machine cannot detect that the Scanner Carriage is connected.
• The machine cannot communicate with the Scanner Carriage.
• The communication data is incorrect.
• Scanner Carriage defective
• IPU defective
• BCU defective
• Harness defective
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Reconnect the following connectors;
• Scanner Carriage - IPU harness (FFC)
• IPU- BCU harness
2. Replace the Scanner Carriage.
3. Replace the IPU.
4. Replace the BCU.
5. Replace the following harnesses;
• Scanner Carriage - IPU harness (FFC)
• IPU - BCU harness
Service Call 101-195
SC No.
SC151-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Black Level Error: Side 2
The black level scanned is not specified range.
• CIS for SPDF defective
• SPDF main board defective
• Harness defective
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Reconnect the SPDF main board - CIS connectors if they are disconnected, or loose.
2. Replace the CIS for SPDF
3. Replace the following harnesses;
• SPDF main board - CIS
• IPU -SPDF main board
4. Replace the SPDF main board.
779
780
6. Troubleshooting
SC No.
SC152-00
Type
D
Error Name/Error Condition/Major Cause/Solution
White Level Error: Side 2
• The shading data peak value read out from the CIS is not specified range from the target value.
• CIS defective
• White roller defective
• SPDF main board defective
• Harness defective
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Reconnect the SPDF main board - CIS connectors if they are disconnected, or loose.
2. Replace the CIS for SPDF
3. Replace the following harnesses;
• SPDF main board - CIS
• IPU -SPDF main board
4. Replace the SPDF main board.
Service Call 101-195
SC No.
SC154-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Scanner Communication Error: Side 2
The value read out from the ASIC and FROM area inside the CIS is different from the expected value.
• CIS defective
• "FROM" area error
• SPDF main board defective
• Connector defective (loose, broken)
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Reconnect the SPDF main board - CIS connectors if they are disconnected, or loose.
2. Replace the CIS for SPDF
3. Replace the following harnesses;
• SPDF main board - CIS
• IPU -SPDF main board
4. Replace the SPDF main board.
781
782
6. Troubleshooting
SC No.
SC161-02
SC No.
SC161-20
Type
D
Error Name/Error Condition/Major Cause/Solution
IPU error (Lsync Error: Side 2)
The machine detects the error from the results of self-diagnostic test before scanning the side 2.
• harness defective between CIS and IPU (disconnected, loose)
• CIS defective
• IPU defective (ASIC: Macaron error)
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Reconnect the IPU - CIS connectors if they are disconnected, or loose.
2. Replace the CIS for SPDF.
3. Replace the IPU - CIS harness.
4. Replace the IPU.
Type
D
Error Name/Error Condition/Major Cause/Solution
IPU error (DRAM initialization failure)
An error occurred during performed every time the machine is turned on, or returns to full operation from energy save mode.
• IPU defective (Macaron/ DRAM device connection error)
• DRAM device defective
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Reconnect the all connectors on IPU board if they are disconnected, or loose.
2. Replace the IPU, and BCU.
Service Call 101-195
SC No.
SC195-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Machine serial number error
Comparison of the product identification code in the machine serial number (11 digits).
The product identification code in the machine serial number (11 digits) does not match.
Re-enter the machine serial number.
783
784
6. Troubleshooting
SC No.
SC202-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Polygon Motor: ON Timeout Error
After the polygon motor turned on, or within the specified time (sec.) after the rpm’s changed, the motor did not enter READY status.
• The interface harness to the polygon motor driver damaged or not connected correctly.
• Polygon motor or polygon motor driver defective
• Polygon motor drive pulse cannot be output correctly. (Polygon controller)
• XSCRDY signal observation failing (Polygon controller)
1. Turn the main power OFF/ON.
2. Reconnect the connectors between LD unit and IPU.
3. Check CN586 (a connector with 1 pin) for the polygon mirror motor from the PSU.
4. Replace the LD unit (Polygon mirror motor).
5. Replace the harness between the LD unit and IPU.
6. Replace the IPU.
7. Replace the PSU (or fuses on PSU).
Service Call 202-285
SC No.
SC203-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Polygon Motor: OFF Timeout Error
The XSCRDY signal (polygon ready) never becomes inactive (H) within 3 sec. after the polygon motor went OFF.
• The interface harness to the polygon motor driver damaged or not connected correctly.
• Polygon motor or polygon motor driver defective
• Polygon motor drive pulse cannot be output correctly. (Polygon controller)
• XSCRDY signal observation failing (Polygon controller)
1. Turn the main power OFF/ON.
2. Reconnect the harness between LD unit and IPU.
3. Check CN586 (a connector with 1 pin) for the polygon mirror motor from the PSU.
4. Replace the LD unit (Polygon mirror motor).
5. Replace the harness between the LD unit and IPU.
6. Replace the IPU.
7. Replace the PSU (or fuses on PSU).
785
786
6. Troubleshooting
SC No.
SC204-00
SC No.
SC220-01
SC220-04
Type
D
Error Name/Error Condition/Major Cause/Solution
Polygon Motor: XSCRDY Signal Error
During polygon motor rotation, the XSCRDY signal was inactive (H) for longer than one rotation of the polygon.
• The interface harness to the polygon motor driver damaged or not connected correctly.
• Polygon motor or polygon motor driver defective
1. Turn the main power OFF/ON.
2. Reconnect the connectors between LD unit and IPU.
3. Check CN586 (a connector with 1 pin) for the polygon mirror motor from the PSU.
4. Replace the LD unit (Polygon mirror motor).
5. Replace the harness between the LD unit and IPU.
6. Replace the IPU.
7. Replace the PSU (or fuses on PSU).
Type
D
D
Error Name/Error Condition/Major Cause/Solution
Leading Edge: LD1 synchronization detection error: Bk
Leading Edge: LD1 synchronization detection error: Ye
Service Call 202-285
SC No.
SC No.
SC230-01
SC230-02
SC230-03
SC230-04
Type Error Name/Error Condition/Major Cause/Solution
The leading edge LD0 synchronization detection signal of the corresponding color was not output within the specified time (sec.) while the polygon mirror motor was operating at normal speed.
• The interface harness to the synchronization detection unit damaged or not connected correctly.
• Synchronization detection board defective
• Beam does not enter photo detector.
• Abnormality around GAVD
• LDB defective
1. Turn the main power OFF/ON.
2. Check for condensation on the LDB.
3. Reconnect the connectors between LDB (Synchronizing detector board) and IPU.
4. Replace the LD unit.
5. Replace the IPU
6. Replace the harness between LDB (Synchronizing detector board) and IPU.
Type
D
D
D
D
Error Name/Error Condition/Major Cause/Solution
FGATE ON error: Bk
FGATE ON error: Cy
FGATE ON error: Ma
FGATE ON error: Ye
The FGATE signal did not turn ON within the specified time (sec.) after the writing process of the corresponding color started.
• Image processing ASIC defective on IPU
• Harness between IPU and LDB defective
1. Turn the main power OFF/ON.
2. Reconnect the connectors between IPU and controller board.
3. Replace the IPU.
787
788
6. Troubleshooting
SC No.
SC231-01
SC231-02
SC231-03
SC231-04
SC No.
SC240-01
SC240-02
SC240-03
SC240-04
Type
D
D
D
D
Error Name/Error Condition/Major Cause/Solution
FGATE OFF error: Bk
FGATE OFF error: Cy
FGATE OFF error: Ma
FGATE OFF error: Ye
• The FGATE signal did not turn OFF within the specified time (sec.) after the writing process of the corresponding color ended.
• The FGATE signal did not turn OFF when the next job of the corresponding color started.
• Image processing ASIC defective on IPU
• Harness between IPU and LDB defective
1. Turn the main power OFF/ON.
2. Reconnect the connectors between IPU and controller board.
3. Replace the IPU.
Type
D
D
D
D
Error Name/Error Condition/Major Cause/Solution
LD error: Bk
LD error: Cy
LD error: Ma
LD error: Ye
Service Call 202-285
SC No.
SC No.
SC272-01
SC272-02
SC272-03
SC272-04
Type Error Name/Error Condition/Major Cause/Solution
• If LD error terminal of LD driver of corresponding color is asserted after LD initialization.
• If an error is detected during initialization of LD driver which detects
Ith/Ieta of LD of corresponding color.
• LD degradation (LD broken, shift of output characteristics etc.)
• The interface harness damaged or not connected correctly.
• LD driver defective
1. Turn the main power OFF/ON.
2. Check the value in SP2-110-001 to 004 (LD Driver), the default is
"0h".
• If current value is "0", perform step 4.
• If current value is "1", perform steps 3 and 5.
3. Reconnect the connectors between LDB and IPU.
4. Replace the LD unit
5. Replace the harness between LDB to IPU.
Type
D
D
D
D
Error Name/Error Condition/Major Cause/Solution
LD driver communication error: Bk
LD driver communication error: Cy
LD driver communication error: Ma
LD driver communication error: Ye
789
790
6. Troubleshooting
SC No.
SC No.
SC272-10
Type Error Name/Error Condition/Major Cause/Solution
In view of parity, 3 retries were performed
• BCU defective
• Harness defective
• LDB defective
1. Turn the main power OFF/ON.
2. Reconnect the following connectors;
• LDB-IPU harness
• IPU-BCU harness
3. Replace the LD unit.
4. Replace the BCU.
5. Replace the following harnesses;
• LDB-IPU harness
• IPU-BCU harness
Type
D
Error Name/Error Condition/Major Cause/Solution
LD driver communication error: Other
LD voltage does not satisfy the specified voltage (5 V).
• BCU defective (LD5V Power error)
• LDB defective (LD drive error)
• LDB connector defective (loose, broken)
• Interlock switch defective
1. Turn the main power OFF/ON.
2. Reconnect the connectors between LDB and IPU.
3. Replace the IPU.
4. Replace the LD unit.
5. Replace the harness between LDB and IPU.
6. Replace the interlock switch.
Service Call 202-285
SC No.
SC285-01
SC No.
SC285-02
Type
C
Error Name/Error Condition/Major Cause/Solution
Laser optics positioning motor (in LD unit) :Power control error
The power supply from PSU is not supplied to the laser optics positioning motors.
• Software error
• Imaging IOB defective
• BCU defective
1. Turn the main power OFF/ON.
2. Update the firmware.
3. Replace the imaging IOB.
4. Replace the BCU.
Type
C
Error Name/Error Condition/Major Cause/Solution
MUSIC error
The results of MUSIC pattern reading failed 4 times.
(even if mode e (real time MUSIC) fails, the error count is not incremented (+1))
For details about cause and solution, refer to page 966 "When
SC285-02 (MUSIC Error) Is Displayed".
791
792
6. Troubleshooting
SC No.
Type Error Name/Error Condition/Major Cause/Solution
SC312-01 D Charge Roller HVP_CB Output Error (K)
SC312-02 D Charge Roller HVP_CB Output Error (C)
SC312-03 D Charge Roller HVP_CB Output Error (M)
SC312-04 D Charge Roller HVP_CB Output Error (Y)
Charging AC is set to ON at the standard speed, and the FB voltage of the charging AC of each color is monitored for 200 ms at 20ms intervals (10 times) after 80ms of charge AC_ON, and below 0.3V is detected continuously for
200ms (10 times), the SC of the corresponding color lights up, and machine operation is suspended.
• High voltage harness defective or shorted.
• PCU setting fault or damage
• HVP_CB fault
• Connector disconnected
• Harness broken
Service Call 312-396
SC No.
Type Error Name/Error Condition/Major Cause/Solution
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Check the PCU for the following points and recover or replace the PCU if there are any defects.
• Checking contaminants on the Charge Roller terminal [A]
• Checking damage or deformation of the Charge Roller terminal [A]
• Checking continuity to the Charge Roller terminal core bar [B]
2. Check if all connectors related to PCDU are connected securely. Replace the connectors if they are disconnected, or loose.
3. Recover or replace the parts of the main machine if there are any defects after checking the following points.
• Checking contaminants on the charged power supplying plate [C]
• Checking damage or deformation of the charged power supplying plate [C]
• Checking continuity between the Charge Roller terminal core bar and the HVP (CB)
4. Replace the HVP (CB).
5. If SC occurs again, replace the BCU.
793
6. Troubleshooting
SC324-01
RTB 24
SC No.
SC324-01
SC324-05
RTB 24
SC No.
SC324-05
Type
D
Error Name/Error Condition/Major Cause/Solution
Development motor: Bk: Lock
Motor status is observed at 100ms intervals during motor ON, and the unlock status is detected at least 20 times
• Motor defective
• Connector disconnected
• Harness broken
• IOB defective
• Development unit torque increased
• Replace the motor
• Reconnect the connector
• Replace the harness
• Replace the Imaging IOB.
• Replace the development unit
Type
D
Error Name/Error Condition/Major Cause/Solution
Development motor: CMY: Lock
Motor status is observed at 100ms intervals during motor ON, and the unlock status is detected at least 20 times.
• Motor defective
• Connector disconnected
• Harness broken
• IOB defective
• Development unit torque increased
• Replace the motor
• Reconnect the connector
• Replace the harness
• Replace the Imaging IOB.
• Replace the development unit
794
Service Call 312-396
SC No.
SC360-01
SC360-02
SC360-03
SC360-04
SC No.
SC361-01
SC361-02
Type
D
D
D
D
Error Name/Error Condition/Major Cause/Solution
TD sensor adjustment error (K)
TD sensor adjustment error (C)
TD sensor adjustment error (M)
TD sensor adjustment error (Y)
1. Mu count is higher than the threshold which detects no developer.
2. Mu count is lower than the upper/lower target thresholds three consecutive times.
• TD sensor defective
• Loose connection
• Harness broken
• Developer toner density differs from initial developer
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Check if all connectors related to TD sensor are connected securely.
Replace the connectors if they are disconnected, or loose.
2. Check the Development Unit for the following points and recover or replace it if there are any defects.
• Gear came off
• PCDU seal was not removed
• Not initial developer
3. Check the TD sensor and recover or replace it if there are any defects.
4. Check the harness for TD sensor. Replace the harness if it is disconnected, or damaged.
5. Replace the BCU if the SC cannot be recovered even after executing steps 1 to 4.
Type
D
D
Error Name/Error Condition/Major Cause/Solution
TD sensor output error: Upper Limit (K)
TD sensor output error: Upper Limit (C)
795
796
6. Troubleshooting
SC No.
SC361-03
SC361-04
Type
D
D
Error Name/Error Condition/Major Cause/Solution
TD sensor output error: Upper Limit (M)
TD sensor output error: Upper Limit (Y)
TD sensor output: Vt (SP3-210-001 to 004) > output upper limit error threshold (SP3-211-002) continuously exceeded the upper limit occurrence threshold value (SP3-211-003).
TD sensor connector dropout (connection fault)
Service Call 312-396
SC No.
Type Error Name/Error Condition/Major Cause/Solution
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Check if all connectors related to TD sensor are connected securely.
Replace the connectors if they are disconnected, or loose.
2. Check the Development Unit for the following points and recover or replace it if there are any defects.
• Gear comes off
• Development unit is not installed correctly
3. Check the TD sensor and recover or replace it if there are any defects.
4. Check the values of SP3-030-061 to 064 (Init TD Sensor :Exe Initial mu count). If they are initial, perform the TD sensor adjustment
(SP3-030-001 to 006).
5. Check the Toner Supply Unit and recover or replace it if there are any defects. (When the image density is excessively low, the supply unit may have a possibility of abnormality)
• Toner bottle is empty
• Toner bottle drive error
• Clogging in the supplying path
6. Check the harness for TD sensor. Replace the harness if it is disconnected, or damaged.
7. Replace the BCU if the SC cannot be recovered even after executing steps 1 to 6.
Recovery Confirmation Procedure
1. Turn ON the main power, and then print a sheet.
2. Execute SP3-320-***(TD.Sens:Vt :Disp: Current: CMYK) to check the output value of the TD sensor.
3. Execute SP3-211-004 (Vt Limits Err :Disp Lower Threshold) to check the lower limit value.
• Abnormal if the TD sensor output value is lower than the lower limit value
• Normal if the TD sensor output value is equal to or larger than the lower limit value
797
798
6. Troubleshooting
SC No.
SC362-01
SC362-02
SC362-03
SC362-04
Type
D
D
D
D
Error Name/Error Condition/Major Cause/Solution
TD sensor output error: Lower limit (K)
TD sensor output error: Lower limit (C)
TD sensor output error: Lower limit (M)
TD sensor output error: Lower limit (Y)
TD sensor output: Vt (SP3-210-001 to 004) < output lower limit error threshold (SP3-211-004) is continuously below the lower limit occurrence threshold value (SP3-211-005)
TD sensor connector missing/dropout
Service Call 312-396
SC No.
SC No.
SC370-01
Type Error Name/Error Condition/Major Cause/Solution
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Check if all connectors related to TD sensor are connected securely.
Replace the connectors if they are disconnected, or loose.
2. Check the Development Unit for the following points and recover or replace it if there are any defects.
• Gear comes off
• Development unit is not installed correctly
3. Check the TD sensor and recover or replace it if there are any defects.
4. Check the values of SP3-030-061 to 064 (Init TD Sensor :Exe Initial mu count). If they are initial, perform the TD sensor adjustment
(SP3-030-001 to 006).
5. Check the Toner Supply Unit and recover or replace it if there are any defects.
• Toner bottle driving error (left rotating)
6. Check the harness for TD sensor. Replace the harness if it is disconnected, or damaged.
7. Replace the BCU if the SC cannot be recovered even after executing steps 1 to 6.
Recovery Confirmation Procedure
1. Turn ON the main power, and then print a sheet.
2. Execute SP3-320-***(TD.Sens:Vt :Disp: Current: CMYK) to check the output value of the TD sensor.
3. Execute SP3-211-004 (Vt Limits Err :Disp Lower Threshold) to check the lower limit value.
• Abnormal if the TD sensor output value is lower than the lower limit value
• Normal if the TD sensor output value is equal to or larger than the lower limit value
Type
D
Error Name/Error Condition/Major Cause/Solution
TM (ID) sensor calibration error (F)
799
800
6. Troubleshooting
SC No.
SC370-02
SC370-03
SC No.
SC396-05
Type
D
D
Error Name/Error Condition/Major Cause/Solution
TM (ID) sensor calibration error (C)
TM (ID) sensor calibration error (R)
Regular reflection optical output voltage of the Front or Center or Rear
TM (ID) sensor: Vsg_reg cannot be adjusted to within target range.
Upper limit (SP3-320-013: initial value 4.5V)
Lower limit (SP3-320-014: initial value 3.5V)
For details about cause and solution, refer to page 970 "When SC370
(TM (ID) Sensor Calibration Error) Is Displayed".
Type
D
Error Name/Error Condition/Major Cause/Solution
Drum motor (CMY) Lock
Motor status is observed at 100ms intervals during motor ON, and the unlock status is detected at least 20 times
• Motor defective
• Connector disconnected
• Harness broken
• IOB defective
• Unit torque increased.
• Replace the motor
• Reconnect the connector
• Replace the harness
• Replace the Imaging IOB.
• Replace the PCDU
Service Call 441-498
SC No.
SC441-00
Level
D
Error Name/Error Condition/Major Cause/Solution
Drum transfer motor: Lock
Motor status is observed at 100ms intervals during motor ON, and the unlock status is detected at least 20 times.
• Motor defective
• Connector disconnected
• Harness broken
• IOB defective
• Unit torque increased.
• Replace the motor
• Reconnect the connector
• Replace the harness
• Replace the Imaging IOB.
• Check the load on the motor (PCDU, Image transfer unit, Paper transfer unit, Waste toner bottle).
• Replace the PCDU, Image transfer unit, Paper transfer unit or Waste toner bottle.
801
802
6. Troubleshooting
SC No.
SC442-00
Level
D
Error Name/Error Condition/Major Cause/Solution
ITB Lift Error
Even though the ITB contact and release motor (also Toner supply motor
(M)) rotates, the ITB contact and release sensor failed to detect the specified sensor feeler status within specified time.
• Contact/separation operation: If not detected in 2000msec
• Home position operation: If not detected in 5000msec
• Signal detection sampling period: 10msec
• Image transfer unit not set/faulty setting
• Sensor dirt
• Sensor defective
• Motor defective
• Unit load large
1. Reset the Image transfer unit properly.
2. Clean the ITB contact and release sensor
3. Check the harness (disconnected, loose connectors)
4. Replace the ITB contact and release sensor
5. Replace the image transfer unit
6. Replace the contact and release drive unit
Service Call 441-498
SC No.
SC452-00
Level
D
Error Name/Error Condition/Major Cause/Solution
Paper transfer contact motor error
Paper transfer contact motor: position sensor cannot detect the sensor filler state within the predetermined time (see below) even if the paper transfer contact and release motor is rotated.
• Contact operation: If not detected in 2000msec
• Home position operation: If not detected in 5000msec
• Signal detection sampling period: 10msec
• Sensor dirt
• Sensor defection
• Motor defection
• Unit load large
• Replace the contact drive unit
• Replace the image transfer unit
• Check the harness
803
804
6. Troubleshooting
SC No.
SC491-00
Level
D
Error Name/Error Condition/Major Cause/Solution
High voltage power source: charge/development: output error
SC detection signal (charge/development) is L (abnormal) for 200 ms consecutively during high voltage (charge/development) output.
H/W error
• Output contact setting fault
• Controller connector set fault
• Ground fault of output high voltage path
• Surface/air clearance insufficient (arc discharge)
• Controller harness disconnection, short-circuit
• PCU setting fault
• Control board _IOB error (related signal error)
• HVP_CB error
Load error
• Grounding fault of charging output, short-circuit with other outputs
• Surface/air clearance insufficient in charging output path (including distance from other outputs)
• Abnormal deterioration of drum, and over current due to pinholes
• Drum vs charge roller gap error (PCU error).
• Over current due to drum surface condensation
• Grounding fault of developing output, short-circuit with other outputs
• Surface/air clearance insufficient in developing output path
(including distance from other outputs)
• Other
• Turn the main power OFF/ON.
• Reset or replace the harness of high voltage power supply feed path
• Reset or replace the harness between IOB-HVP_CB
• Reset or replace the PCU
• Check the operation of the contact mechanism
• Replace the HVP_CB
• Replace the Imaging IOB.
Service Call 441-498
SC No.
SC492-00
Level
C
Error Name/Error Condition/Major Cause/Solution
High voltage power source: image transfer/paper transfer: output error
SC detection signal (transfer) is L (abnormal) for 200 ms consecutively during high voltage (transfer) output.
H/W error
• Output power connector setting fault
• Controller connector setting fault
• Output high voltage Harness disconnection
• Controller harness disconnection, short-circuit
• Transfer unit setting fault
• Control board_ IOB error (related signal error)
• HVP_TTS error
Load error
• Increase in paper transfer roller impedance (low temperature environment/impedance rise/impedance rise due to dirt)
• Operation fault of paper transfer contact mechanism
• Increase in image transfer belt impedance
• Opening in load power supply path
• Reset or replacement the harness of high voltage power supply feed path
• Reset or replace the harness between IOB-HVP_TTS
• Reset or replace the transfer unit
• Check operation of the contact mechanism
• Replace the HVP_TTS
• Replace the Imaging IOB.
805
806
6. Troubleshooting
SC No.
SC497-00
SC No.
SC498-00
Level
C
Error Name/Error Condition/Major Cause/Solution
Machine temperature detection thermistor error
Temperature sensor output error: Below 0.56V, or above 3.0V
• Connector disconnection or broken
• Sensor (Thermistor) defective
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Check if all connectors related to the Imaging Temperature Sensor
(Thermistor) are connected securely. Reconnect the connectors if they are disconnected, or loose.
2. Replace the Imaging Temperature Sensor (Thermistor).
Level
C
Error Name/Error Condition/Major Cause/Solution
Temperature and humidity sensor error
Temperature sensor output error: Below 0.76V, or above 2.90V, or
Moisture sensor output error: more than 2.4V
• Sensor not setting (disconnection or broken)
• Sensor defective
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Check if all connectors related to the Temperature and Humidity
Sensor are connected securely. Reconnect the connectors if they are disconnected, or loose.
2. Replace the Temperature and Humidity Sensor.
Service Call 501-584
SC No.
SC501-01
Type
B
Error Name/Error Condition/Major Cause/Solution
1st Tray Lift Error (Main Machine)
The 1st tray lift motor error detection count reaches 3 times.
(Up to 2 times, reset instruction is displayed)
• 1st tray upper limit sensor connector missing, malfunction, dirt
• 1st tray lift motor connector missing, disconnection, malfunction.
• Foreign object, such as paper scrap, is caught between the paper feed tray and the tray lift motor.
• Paper set incorrectly
• Reload the paper.
• Remove the foreign object.
1st tray upper limit sensor, 1st tray lift motor
• Check the harness.
• Reset the connector.
• Replace
1st paper feed unit, 1st tray
• Replace
Paper transport IOB
• Replace
807
808
6. Troubleshooting
SC No.
SC501-02
Type
B
Error Name/Error Condition/Major Cause/Solution
1st Tray Descent Error (Main Frame)
The 1st tray descent motor error detection count reaches 5.
(Up to 4, reset instruction is displayed.)
• 1st tray upper limit sensor connector missing, malfunction, dirt
• 1st tray lift motor connector missing, disconnection, malfunction
• Foreign object, such as paper scrap, is caught between the paper feed tray and the tray lift motor.
• Paper set incorrectly
• Paper overload
• Reset the paper.
• Remove the foreign object.
1st tray upper limit sensor, 1st tray lift motor
• Check the harness.
• Reset the connector.
• Replace
1st paper feed unit, 1st tray
• Replace
Paper transport IOB
• Replace
Service Call 501-584
SC No.
SC502-01
Type
B
Error Name/Error Condition/Major Cause/Solution
2nd Tray Lift Error (Main Frame)
The 2nd tray lift motor error detection count reaches 3.
(Up to 2, reset is displayed.)
• 2nd tray upper limit sensor connector missing, malfunction, dirt
• 2nd tray lift motor connector missing, disconnection, malfunction
• Foreign object, such as paper scrap, is caught between the paper feed tray and the tray lift motor
• Paper set incorrectly
• Reset the paper.
• Remove the foreign object.
2nd tray upper limit sensor, 2nd tray lift motor
• Check the harness.
• Reset the connector.
• Replace
2nd paper feed unit, 2nd tray
• Replace
Paper transport IOB
• Replace
809
810
6. Troubleshooting
SC No.
SC502-02
Type
B
Error Name/Error Condition/Major Cause/Solution
2nd Tray Descent Error (Main Frame)
The detection count of 2nd tray descent motor descent errors reaches a total of 5.
(Up to 4, reset is displayed.)
• 2nd tray upper limit sensor connector missing, malfunction, and dirt
• 2nd tray lift motor connector missing, disconnection, malfunction
• Foreign object, such as paper scrap, is caught between the paper feed tray and the tray lift motor
• Paper set incorrectly
• Paper overload
• Reset the paper.
• Remove the foreign object.
2nd tray upper limit sensor, 2nd tray lift motor
• Check the harness.
• Reset the connector.
• Replace
2nd paper feed unit, 2nd tray
• Replace
Paper transport IOB
• Replace
Service Call 501-584
SC No.
SC503-01
Type
B
Error Name/Error Condition/Major Cause/Solution
3rd Tray Lift Error (Paper Feed Unit PB3150 (D694))
• Lift motor ascent error detection
During tray initialization (upper limit not detected/lower limit detection), the tray base plate is raised to check the tray base plate position, and the upper limit sensor is not detected although a predetermined time elapsed, for 3 times consecutively.
(Up to 2 times consecutively, the bank transmits a "tray set incorrectly" to the main machine.)
• Lift motor error/connector missing
• Upper limit sensor error/connector missing
• Harness broken
• Bank control board defective
• Foreign object, such as paper scrap, is caught between the paper feed tray and the tray lift motor
• Paper set incorrectly
Remove the jammed paper or slip of paper from the tray, and check if the
SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Check if all connectors in Tray 3 are connected securely. Reconnect the connectors if they are disconnected, or loose.
2. Check the harness in Tray 3. Replace the harnesses if it is disconnected, or damaged.
3. Check if the motor runs, sensors turn OFF/ON, has no overloads, and is properly driven. Replace the parts if there are any defects.
4. Check if there are any signs of a short circuit. Replace the parts if there are any defects.
811
812
6. Troubleshooting
SC No.
SC503-02
Type
B
Error Name/Error Condition/Major Cause/Solution
3rd Tray Descent Error (Paper Feed Unit PB3150 (D694))
• Lift motor descent error detection
During tray initialization, the tray base plate is lowered to check the tray base plate position, and the upper limit sensor is detected although a predetermined time elapsed, for 3 times consecutively.
(Up to 2 times consecutively, the bank transmits a "tray set incorrectly" to the main machine.)
• Lift motor error/connector missing
• Upper limit sensor error/connector missing
• Harness broken
• Bank control board defective
• Paper overload
• Foreign object, such as paper scrap, is caught between the paper feed tray and the tray lift motor
• Paper set incorrectly
Remove the jammed paper or slip of paper from the tray, and check if the
SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Check if all connectors in Tray 3 are connected securely. Reconnect the connectors if they are disconnected, or loose.
2. Check the harness in Tray 3. Replace the harnesses if it is disconnected, or damaged.
3. Check if the motor runs, sensors turn OFF/ON, has no overloads, and is properly driven. Replace the parts if there are any defects.
4. Check if there are any signs of a short circuit. Replace the parts if there are any defects.
Service Call 501-584
SC No.
SC503-11
Type
B
Error Name/Error Condition/Major Cause/Solution
3rd Tray Lift Error (Upper Tray: Paper Feed Unit PB3220/PB3210
(D787))
• Lift motor ascent error detection
During tray initialization (upper limit not detected/lower limit detection), the tray base plate is raised to check the tray base plate position, and the upper limit sensor is not detected although a predetermined time elapsed, for 3 times consecutively.
(Up to 2 times consecutively, the bank transmits a "tray set incorrectly" to the main machine.)
• Lift motor error/connector missing
• Upper limit sensor error/connector missing
• Harness broken
• Bank control board defective
• Foreign object, such as paper scrap, is caught between the paper feed tray and the tray lift motor
• Paper set incorrectly
Remove the jammed paper or slip of paper from the tray, and check if the
SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Check if all connectors in Tray 3 are connected securely. Reconnect the connectors if they are disconnected, or loose.
2. Check the harness in Tray 3. Replace the harnesses if it is disconnected, or damaged.
3. Check if the motor runs, sensors turn OFF/ON, has no overloads, and is properly driven. Replace the parts if there are any defects.
4. Check if there are any signs of a short circuit. Replace the parts if there are any defects.
813
814
6. Troubleshooting
SC No.
SC503-12
Type
B
Error Name/Error Condition/Major Cause/Solution
3rd Tray Descent Error(Upper Tray: Paper Feed Unit PB3220/PB3210
(D787))
• Lift motor descent error detection
During tray initialization, the tray base plate is lowered to check the tray base plate position; the upper limit sensor is detected although a predetermined time elapsed, for 3 times consecutively.
(Up to 2 times consecutively, the bank transmits a "tray set incorrectly" to the main machine.)
• Lift motor error/connector missing
• Upper limit sensor error/connector missing
• Harness broken
• Bank control board defective
• Paper overload
• Foreign object, such as paper scrap, is caught between the paper feed tray and the tray lift motor
• Paper set incorrectly
Remove the jammed paper or slip of paper from the tray, and check if the
SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Check if all connectors in Tray 3 are connected securely. Reconnect the connectors if they are disconnected, or loose.
2. Check the harness in Tray 3. Replace the harnesses if it is disconnected, or damaged.
3. Check if the motor runs, sensors turn OFF/ON, has no overloads, and is properly driven. Replace the parts if there are any defects.
4. Check if there are any signs of a short circuit. Replace the parts if there are any defects.
Service Call 501-584
SC No.
SC504-21
Type
B
Error Name/Error Condition/Major Cause/Solution
4th Tray Lift Error (Lower Tray: Paper Feed Unit PB3220/PB3210
(D787))
• Lift motor ascent error detection
During tray initialization (upper limit not detected/lower limit detection), the tray base plate is raised to check the tray base plate position, but the upper limit sensor is not detected although a predetermined time elapsed, for 3 times consecutively.
(Up to 2 times consecutively, the bank transmits a "tray set incorrectly" to the main machine.)
• Lift motor error/connector missing
• Upper limit sensor error/connector missing
• Harness broken
• Bank control board defective
• Foreign object, such as paper scrap, is caught between the paper feed tray and the tray lift motor
• Paper set incorrectly
Remove the jammed paper or slip of paper from the tray, and check if the
SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Check if all connectors in Tray 4 are connected securely. Reconnect the connectors if they are disconnected, or loose.
2. Check the harness in Tray 4. Replace the harnesses if it is disconnected, or damaged.
3. Check if the motor runs, sensors turn OFF/ON, has no overloads, and is properly driven. Replace the parts if there are any defects.
4. Check if there are any signs of a short circuit. Replace the parts if there are any defects.
815
816
6. Troubleshooting
SC No.
SC504-22
Type
B
Error Name/Error Condition/Major Cause/Solution
4th Tray Descent Error (Lower Tray: Paper Feed Unit PB3220/PB3210
(D787))
• Lift motor descent error detection
During tray initialization, the tray base plate is lowered to check the tray base plate position, but the upper limit sensor is detected although a predetermined time elapsed, for 3 times consecutively.
(Up to 2 times consecutively, the bank transmits a "tray set incorrectly" to the main machine.)
• Lift motor error/connector missing
• Upper limit sensor error/connector missing
• Harness broken
• Bank control board defective
• Paper overload
• Foreign object, such as paper scrap, is caught between the paper feed tray and the tray lift motor
• Paper set incorrectly
Remove the jammed paper or slip of paper from the tray, and check if the
SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Check if all connectors in Tray 4 are connected securely. Reconnect the connectors if they are disconnected, or loose.
2. Check the harness in Tray 4. Replace the harnesses if it is disconnected, or damaged.
3. Check if the motor runs, sensors turn OFF/ON, has no overloads, and is properly driven. Replace the parts if there are any defects.
4. Check if there are any signs of a short circuit. Replace the parts if there are any defects.
Service Call 501-584
SC No.
SC508-00
SC No.
SC520-01
SC520-02
SC520-03
SC No.
SC521-01
SC521-02
Type
B
Error Name/Error Condition/Major Cause/Solution
Bypass Tray Size Detection Error
The paper size detected on the bypass tray is different from any of the pattern of automatic size detection.
• Bypass length sensor or bypass width sensor malfunction
• Bypass length sensor or bypass width sensor harness disconnected
1. Replace the Bypass Length Sensor, or Bypass Width Sensor.
2. Replace the harness for bypass length sensor, or bypass width sensor.
Type
C
C
C
Error Name/Error Condition/Major Cause/Solution
Registration Motor: Lock
Paper feed Motor: Lock
Transport Motor: Lock
During motor ON, after checking the motor error notification registers
(err_velo and err_posi) for 0.5 sec, the error state of either register was detected at least 5 times.
• Motor defective
• Connector disconnected
• Harness broken
• IOB defective
• Encoder defective
• Replace the motor.
• Reset the connector.
• Replace the harness.
• Replace the paper transport IOB.
Type
C
C
Error Name/Error Condition/Major Cause/Solution
Duplex Entrance Motor: Lock
Duplex Bypass Motor: Lock
817
818
6. Troubleshooting
SC No.
SC No.
SC522-00
Type Error Name/Error Condition/Major Cause/Solution
During motor ON, after checking the motor error notification registers
(err_velo and err_posi) for 0.5 sec, the error state of either register was detected at least 5 times.
• Motor defective
• Connector disconnected
• Harness broken
• IOB defective
• Encoder defective
• Replace the motor.
• Reset the connector.
• Replace the harness.
• Replace the paper transport IOB.
Type
C
Error Name/Error Condition/Major Cause/Solution
Paper Exit Motor: Lock
During motor ON, after checking the motor error notification registers
(err_velo and err_posi) for 0.5 sec, the error state of either register was detected at least 5 times.
• Motor defective
• Connector disconnected
• Harness broken
• IOB defective
• Encoder defective
• Replace the motor.
• Reset the connector.
• Replace the harness.
• Replace the paper transport IOB.
Service Call 501-584
SC No.
SC530-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Fusing Exhaust Fan Lock
In the motor ON state, the value of the lock sensor is checked every 0.1
sec.
If a lock signal is not obtained for 50 times consecutively.
• Motor defective
• Connector disconnected
• Harness broken
• IOB defective
• Replace the fusing exhaust fan.
• Reconnect the connector.
• Replace the harness.
• Replace the paper transport IOB.
SC No.
SC531-01
SC531-03
Type
D
D
Error Name/Error Condition/Major Cause/Solution
Development Intake Fan/Right Lock
Drive Cooling Fan Lock
In the motor ON state, the value of the lock sensor is checked every 0.1
sec.
If a lock signal is not obtained for 50 times consecutively.
• Motor defective
• Connector disconnected
• Harness broken
• IOB defective
• Replace the development intake fan/right for SC531-01, or drive cooling fan for SC531-03.
• Reconnect the connector.
• Replace the harness.
• Replace the imaging IOB.
819
820
6. Troubleshooting
SC No.
SC533-03
SC533-04
SC No.
SC534-01
SC534-02
SC534-03
Type
D
D
Error Name/Error Condition/Major Cause/Solution
PSU Cooling Fan Lock
Controller Box Cooling Fan Lock
In the motor ON state, the value of the lock sensor is checked every 0.1
sec.
If a lock signal is not obtained for 50 times consecutively.
• Motor defective
• Connector disconnected
• Harness broken
• IOB defective
• Replace the PSU exhaust fan for SC533-01, PSU cooling fan for
SC533-04 or controller box cooling fan for SC533-04.
• Reconnect the connector.
• Replace the harness.
• Replace the paper transport IOB (for SC533-01, -03).
• Replace the imaging IOB (for SC533-04).
Type
D
D
D
Error Name/Error Condition/Major Cause/Solution
Main Exhaust Fan Lock
Toner Supply Cooling Fan Lock
Ozone Exhaust Fan Lock
Service Call 501-584
SC No.
SC No.
SC535-00
Type Error Name/Error Condition/Major Cause/Solution
In the motor ON state, the value of the lock sensor is checked every 0.1
sec.
If a lock signal is not obtained for 50 times consecutively.
• Motor defective
• Connector disconnected
• Harness broken
• IOB defective
• Replace the development intake fan/right for SC534-01, or drive cooling fan for SC534-03.
• Reconnect the connector.
• Replace the harness.
• Replace the imaging IOB (SC534-01, -02).
• Replace the paper transport IOB (for SC534-03).
Type
D
Error Name/Error Condition/Major Cause/Solution
Paper Exit Cooling Fan Lock
In the motor ON state, the value of the lock sensor is checked every 0.1
sec.
If a lock signal is not obtained for 50 times consecutively.
• Motor defective
• Connector disconnected
• Harness broken
• IOB defective
• Replace the paper exit cooling fan.
• Reconnect the connector.
• Replace the harness.
• Replace the imaging IOB.
821
822
6. Troubleshooting
SC No.
SC540-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Fusing Motor: Lock
Motor status is observed at 0.1 sec intervals during motor ON, and the unlock status is detected at least 20 times.
• Motor defective
• Connector disconnected
• Harness broken
• IOB defective
• Unit torque increased
• Replace the fusing motor.
• Reconnect the connector.
• Replace the harness.
• Replace the paper transport IOB.
SC No.
SC541-01
Type
A
Error Name/Error Condition/Major Cause/Solution
Thermopile (Center) Disconnection
Below -50 degrees C (or below CB) is detected for 0.1 sec continuously.
• Thermopile disconnection
• Connector disconnected
• Harness disconnection between the fusing unit and the BCU
• BCU defective
1. Reconnect the connectors (main machine side, BCU side).
2. Replace the thermopile (center).
3. Replace the harness between the fusing unit and the BCU.
4. Replace the BCU.
Service Call 501-584
SC No.
SC541-02
SC541-03
Type
A
A
Error Name/Error Condition/Major Cause/Solution
Non-contact Thermistor (Center) Disconnection
Above 3F6 is detected for 1 sec. continuously (NC sensor center: detection & compensation NC sensor edge: detection & compensation).
Detection period: 0.1 sec, detection frequency: 10 times or more.
• Non-contact thermistor disconnection
• Connector disconnected
• Harness disconnection in the fusing unit
• Harness disconnection between the fusing unit and the BCU
• BCU defective
1. Reconnect the connectors (between the fusing unit and the BCU).
2. Replace the non-contact thermistor with the harness.
3. Replace the fusing unit.
4. Replace the harness between the fusing unit and the BCU.
5. Replace the BCU.
Non-contact Thermistor (Center) short-circuit
Below AD value: 8 is detected for 1 sec. continuously.
Detection period: 0.1 sec, detection frequency: 10 times or more.
• Non-contact thermistor short-circuit
• Connector disconnected
• Harness disconnection in the fusing unit
• Harness disconnection between the fusing unit and the BCU
• BCU defective
1. Reconnect the connectors (between the fusing unit and the BCU).
2. Replace the non-contact thermistor with the harness.
3. Replace the fusing unit.
4. Replace the harness between the fusing unit and the BCU.
5. Replace the BCU.
823
824
6. Troubleshooting
SC No.
SC542-02
SC542-03
SC542-05
SC542-06
Type
A
A
D
D
Error Name/Error Condition/Major Cause/Solution
Thermopile (Center) does not reload
65 degrees C not reached after fusing lamp 1 ON for 10 sec continuously.
Thermopile (Center) does not reload
Heating central reload permission temperature not reached after fusing lamp 1 ON for 35 sec continuously.
Thermopile (Center) does not reload (Low Power)
65 degrees C not reached after fusing lamp 1 ON for 10 sec continuously.
Thermopile (Center) does not reload (Low Power)
Heating central reload permission temperature not reached after fusing lamp 1 ON for 35 sec continuously.
Service Call 501-584
SC No.
Type Error Name/Error Condition/Major Cause/Solution
• Outside input voltage guarantee
• Jammed paper between the thermopile and fusing unit
• Thermopile lens dirt
• Thermopile modification/float
• After excessive temperature rise prevention unit operation
• Fusing lamp disconnection
• Harness disconnection between the fusing unit and the BCU or the
PSU (AC controller board)
• BCU defective
• AC controller board defective
1. Check the power supply voltage and reconnect the cable to the outlet.
2. Remove the jammed paper between the thermopile and fusing unit.
3. Clean or replace the thermopile (center).
4. Replace the fusing sleeve thermostat
5. Replace the fusing sleeve belt unit.
6. Reconnect or replace the harness between the fusing unit and the
BCU or the PSU (AC controller board).
7. Replace the BCU.
8. Replace the PSU (AC controller board).
825
826
6. Troubleshooting
SC No.
SC543-00
Type
A
Error Name/Error Condition/Major Cause/Solution
Thermopile (Center) high temperature detection (software)
Above 240 degrees C detected for 1 sec continuously.
Detection period: 0.1 sec, detection count: 10 times or more.
• Fusing sleeve belt defective
• Paper setting misdetection
• Incorrect paper position in the paper feed tray
• Gear abrasion
• Thermopile failure
• Harness disconnection between the fusing unit and the BCU or the
PSU (AC controller board)
• Triac defective (short-circuit)
• BCU failure
• AC controller board failure
1. Inspect the fusing sleeve belt unit, and replace if damaged.
2. Check the paper settings.
3. Check the paper position in the paper feed tray.
4. Reconnect the connectors (main machine side, BCU side).
5. Inspect or replace the gears in the fusing unit or main machine.
6. Replace the thermopile (center).
7. Replace the harness between the fusing unit and the BCU or the PSU
(AC controller board).
8. Replace the BCU.
9. Replace the PSU (AC controller board).
If the problem cannot be solved after performing the above steps, replace the fusing unit.
Service Call 501-584
SC No.
SC544-01
Type
A
Error Name/Error Condition/Major Cause/Solution
Thermopile (Center) high temperature detection (hardware)
In the event of an error
• Fusing sleeve belt defective
• Paper setting misdetection
• Incorrect paper position in the paper feed tray
• Gear abrasion
• Pressure roller HP sensor disconnected
• Thermopile failure
• Harness disconnection between the fusing unit and the BCU or the
PSU (AC controller board)
• Triac defective (short-circuit)
• BCU failure
• AC controller board failure
1. Inspect the fusing sleeve belt unit, and replace if damaged.
2. Check the paper settings.
3. Check the paper position in the paper feed tray.
4. Reconnect the connectors (main machine side, BCU side).
5. Inspect or replace the gears in the fusing unit or main machine.
6. Inspect the pressure roller HP sensor with SP5-803-047.
7. Replace the thermopile (center).
8. Replace the harness between the fusing unit and the BCU or the PSU
(AC controller board).
9. Replace the BCU.
10. Replace the PSU (AC controller board).
If the problem cannot be solved after performing the above steps, replace the fusing unit.
827
828
6. Troubleshooting
SC No.
SC544-02
SC No.
SC545-01
Type
A
Error Name/Error Condition/Major Cause/Solution
Non-contact Thermistor (Center) high temperature detection (hardware)
In the event of an error
• Fusing sleeve belt defective
• Paper setting misdetection
• Incorrect paper position in the paper feed tray
• Jammed paper between the thermopile and fusing unit
• Thermopile lens dirt
• Thermopile modification/float
• Pressure roller HP sensor disconnected
• Harness disconnection between the fusing unit and the BCU or the
PSU (AC controller board)
• Triac defective (short-circuit)
• BCU failure
• AC controller board failure
1. Inspect the fusing sleeve belt unit, and replace if damaged.
2. Check the paper settings.
3. Check the paper position in the paper feed tray.
4. Reconnect the connectors (main machine side, BCU side).
5. Remove the jammed paper between the thermopile and fusing unit.
6. Clean or replace the thermopile (center).
7. Replace the fusing unit.
8. Inspect the pressure roller HP sensor with SP5-803-047.
9. Replace the harness between the fusing unit and the BCU or the PSU
(AC controller board).
10. Replace the BCU.
11. Replace the PSU (AC controller board).
Type
A
Error Name/Error Condition/Major Cause/Solution
Fusing Central Lamp Continuously Heat
Service Call 501-584
SC No.
SC545-05
Type
D
Error Name/Error Condition/Major Cause/Solution
Fusing Central Lamp Continuously Heat (Low Power)
After waiting for full power for more than 5 sec continuously.
• Definition of fusing lamp full power
Continuously heating rate set point (maximum heating rate)
• Measurement start point
After reload (after fusing lamp extinguished, after rotation complete) below the standby temperature (target temperature), measurement starts after a fusing lamp heat-up request is issued.
• Measurement stop condition
Rotation started due to a print signal during measurement or other.
• Maximum heat-up duty (SP interlinked value) 0% is excluded.
• Outside input voltage guarantee
• Jammed paper between the thermopile and fusing unit
• Thermopile lens dirt
• Thermopile modification/float
• After excessive temperature rise prevention unit operation
• Fusing lamp disconnection
• Harness disconnection between the fusing unit and the BCU or the
PSU (AC controller board)
• BCU defective
• AC controller board defective
1. Check the power supply voltage and reconnect the cable to the outlet.
2. Remove the jammed paper between the thermopile and fusing unit.
3. Clean or replace the thermopile (center).
4. Replace the fusing sleeve thermostat.
5. Replace the fusing sleeve belt unit.
6. Reconnect or replace the harness between the fusing unit and the
BCU or the PSU (AC controller board).
7. Replace the BCU.
8. Replace the PSU (AC controller board).
829
830
6. Troubleshooting
SC No.
SC547-01
SC547-02
SC547-03
Type
D
D
D
Error Name/Error Condition/Major Cause/Solution
Zero cross error (relay-contact soldering)
Zero-cross signal is detected while the fusing relay is OFF.
• Fusing relay defective (contact soldering)
• Fusing relay drive circuit error
1. Reconnect the connectors between PSU (AC controller board) and paper transport IOB.
2. Replace the PSU (AC controller board).
3. Replace the paper transport IOB.
Zero cross error (relay contact error)
Zero-cross signal is not detected while the fusing relay is ON.
• Fusing relay damage (contact open)
• Fusing relay drive circuit error
• PSU fuse (24 VS) blowout
1. Reconnect the connectors between PSU (AC controller board) and
Paper transport IOB.
2. Replace the PSU (AC controller board).
3. Replace the paper transport IOB.
4. Replace the harness between PSU (AC controller board) and paper transport IOB.
Zero cross error (low-frequency error)
Mains power supply frequency is determined to be 44 Hz or lower.
Frequency instability of mains power supply
1. Check that the mains power supply frequency is higher than 44 Hz.
If it is equal to or lower than 44 Hz, infrastructure may have defects to be dealt with.
2. Replace the PSU (AC controller board).
Service Call 501-584
SC No.
SC551-01
SC551-02
Type
A
A
Error Name/Error Condition/Major Cause/Solution
Thermopile (Edge) Disconnection
Below -50 degrees C (or below CB) is detected for 0.1 sec continuously.
• Thermopile disconnection
• Connector disconnected
• Harness disconnection between the fusing unit and the BCU
• BCU defective
1. Reconnect the connectors (main machine side, BCU side).
2. Replace the thermopile (edge).
3. Replace the harness between the fusing unit and the BCU.
4. Replace the BCU.
Non-contact Thermistor (Edge) Disconnection
Above 3F6 is detected for 1 sec continuously (NC sensor center: detection & compensation NC sensor edge: detection & compensation).
Detection period: 0.1 sec, detection frequency: 10 times or more.
• Non-contact thermistor disconnection
• Connector disconnected
• Harness disconnection in the fusing unit
• Harness disconnection between the fusing unit and the BCU
• BCU defective
1. Reconnect the connectors (between the fusing unit and the BCU).
2. Replace the non-contact thermistor with the harness.
3. Replace the fusing unit.
4. Replace the harness between the fusing unit and the BCU.
5. Replace the BCU.
831
832
6. Troubleshooting
SC No.
SC551-03
SC No.
SC552-02
SC552-03
SC552-05
SC552-06
Type
A
Error Name/Error Condition/Major Cause/Solution
Non-contact Thermistor (Edge) Short-circuit
Below AD value: 8 is detected for 1 sec. continuously.
Detection period: 0.1 sec, detection frequency: 10 times or more.
• Non-contact thermistor short-circuit
• Connector disconnected
• Harness disconnection in the fusing unit
• Harness disconnection between the fusing unit and the BCU
• BCU defective
1. Reconnect the connectors (between the fusing unit and the BCU).
2. Replace the non-contact thermistor with the harness.
3. Replace the fusing unit.
4. Replace the harness between the fusing unit and the BCU.
5. Replace the BCU.
Type
A
A
D
D
Error Name/Error Condition/Major Cause/Solution
Thermopile (Edge) Does Not Reload
65 degrees C not reached after fusing lamp 1 ON for 14 sec continuously.
Thermopile (Edge) Does Not Reload
Heating edge reload permission temperature not reached after fusing lamp 1 ON for 28 sec continuously.
Thermopile (Edge) Does Not Reload (Low Power)
65 degrees C not reached after fusing lamp 1 ON for 14 sec continuously.
Thermopile (Edge) Does Not Reload (Low Power)
Heating edge reload permission temperature not reached after fusing lamp 1 ON for 28 sec continuously.
Service Call 501-584
SC No.
Type Error Name/Error Condition/Major Cause/Solution
• Outside input voltage guarantee
• Jammed paper between the thermopile and fusing unit
• Thermopile lens dirt
• Thermopile modification/float
• After excessive temperature rise prevention unit operation
• Fusing lamp disconnection
• Harness disconnection between the fusing unit and BCU or the PSU
(AC controller board)
• BCU defective
• AC controller board defective
1. Check the power supply voltage and reconnect the cable to the outlet.
2. Remove the jammed paper between the thermopile and fusing unit.
3. Clean or replace the thermopile (edge).
4. Replace the fusing sleeve thermostat.
5. Reconnect the fusing sleeve belt unit.
6. Reconnect or replace the harness between the fusing unit and the
BCU or the PSU (AC controller board).
7. Replace the BCU.
8. Replace the PSU (AC controller board).
833
834
6. Troubleshooting
SC No.
SC553-00
Type
A
Error Name/Error Condition/Major Cause/Solution
Thermopile (Edge) High Temperature Detection (software)
Above 240 degrees C detected for 1 sec continuously.
Detection period: 0.1 sec, detection count: 10 times or more.
• Fusing sleeve belt defective
• Paper setting misdetection
• Incorrect paper position in the paper feed tray
• Gear abrasion
• Thermopile failure
• Harness disconnection between the fusing unit and the BCU or the
PSU (AC controller board)
• Triac defective (short-circuit)
• BCU failure
• AC controller board failure
1. Inspect the fusing sleeve belt unit, and replace if damaged.
2. Check the paper settings.
3. Check the paper position in the paper feed tray.
4. Reconnect the connectors (main machine side, BCU side).
5. Inspect or replace the gears in the fusing unit or main machine.
6. Replace the thermopile (edge).
7. Replace the harness between the fusing unit and the BCU or the PSU
(AC controller board).
8. Replace the BCU.
9. Replace the PSU (AC controller board).
If the problem cannot be solved after performing the above steps, replace the fusing unit.
Service Call 501-584
SC No.
SC554-01
Type
A
Error Name/Error Condition/Major Cause/Solution
Thermopile (Edge) high temperature detection (hardware)
In the event of an error
• Fusing sleeve belt defective
• Paper setting misdetection
• Incorrect paper position in the paper feed tray
• Gear abrasion
• Pressure roller HP sensor disconnected
• Thermopile failure
• Harness disconnection between the fusing unit and the BCU
• Triac defective (short-circuit)
• BCU failure
• AC controller board failure
1. Inspect the fusing sleeve belt unit, and replace if damaged.
2. Check the paper settings.
3. Check the paper position in the paper feed tray.
4. Reconnect the connectors (main machine side, BCU side).
5. Inspect or replace the gears in the fusing unit or main machine.
6. Inspect the pressure roller HP sensor with SP5-803-047.
7. Replace the thermopile (edge).
8. Replace the harness between the fusing unit and the BCU or the PSU
(AC controller board).
9. Replace the BCU.
10. Replace the PSU (AC controller board).
If the problem cannot be solved after performing the above steps, replace the fusing unit.
835
836
6. Troubleshooting
SC No.
SC554-02
SC No.
SC555-01
SC555-05
Type
A
Error Name/Error Condition/Major Cause/Solution
Non-contact Thermistor (Edge) high temperature detection (hardware)
In the event of an error
• Fusing sleeve belt defective
• Paper setting misdetection
• Incorrect paper position in the paper feed tray
• Jammed paper between the thermopile and fusing unit
• Thermopile lens dirt
• Thermopile modification/float
• Pressure roller HP sensor disconnected
• Harness disconnection between the fusing unit and the BCU or the
PSU (AC controller board)
• Triac defective (short-circuit)
• BCU failure
• AC controller board failure
1. Inspect the fusing sleeve belt unit, and replace if damaged.
2. Check the paper settings.
3. Check the paper position in the paper feed tray.
4. Reconnect the connectors (main machine side, BCU side).
5. Remove the jammed paper between the thermopile and fusing unit.
6. Clean or replace the thermopile (edge).
7. Replace the fusing unit.
8. Inspect the pressure roller HP sensor with SP5-803-047.
9. Replace the harness between the fusing unit and the BCU or the PSU
(AC controller board).
10. Replace the BCU.
11. Replace the PSU (AC controller board).
Type
A
D
Error Name/Error Condition/Major Cause/Solution
Fusing Edge Lamp Continuously Heat
Fusing Edge Lamp Continuously Heat (Low Power)
Service Call 501-584
SC No.
Type Error Name/Error Condition/Major Cause/Solution
After waiting for full power for more than 5 sec continuously.
• Definition of fusing lamp full power
Continuously heating rate set point (maximum heating rate)
• Measurement start point
After reload (after fusing lamp extinguished, after rotation complete) below the standby temperature (target temperature), measurement starts after a fusing lamp heat-up request is issued.
• Measurement stop condition
Rotation started due to a print signal during measurement or other
• Maximum heat-up Duty (SP interlinked value) 0% is excluded
• Outside input voltage guarantee
• Jammed paper between the thermopile and fusing unit
• Thermopile lens dirt
• Thermopile modification/float
• After excessive temperature rise prevention unit operation
• Fusing lamp disconnection
• Harness disconnection between the fusing unit and the BCU
• BCU defective
• AC controller board defective
1. Check the power supply voltage and reconnect the cable to the outlet.
2. Remove the jammed paper between the thermopile and fusing unit.
3. Clean or replace the thermopile (edge).
4. Replace the fusing sleeve thermostat.
5. Replace the fusing sleeve belt unit.
6. Reconnect or replace the harness between the fusing unit and the
BCU or the PSU (AC controller board).
7. Replace the BCU.
8. Replace the PSU (AC controller board).
837
838
6. Troubleshooting
SC No.
SC557-00
SC No.
SC558-01
Type
C
Error Name/Error Condition/Major Cause/Solution
Zero Cross Frequency Exceeded
In the event of an error
-
Frequency instability of mains power supply /Noise
Type
C
Error Name/Error Condition/Major Cause/Solution
Low Input Voltage
Input voltage below the specification is detected on the mains power supply
-
Low input of mains power supply
Service Call 501-584
SC No.
SC559-00
Type
A
Error Name/Error Condition/Major Cause/Solution
Fusing Jam Detected for 3 Times Consecutively
Fusing jam (does not reach fusing exit sensor) is detected for 3 times consecutively.
• Detection conditions
Displays the SC559-00 at the time of integrating the counter each time fusing jam occurs, became fusing jam counter value = 3.
The counter value is retained without fusing jam also reset by
OFF/ON the power supply.
• Control ON/OFF
And enables ON / OFF is this SC, the default is set to OFF, then
ON at the time of customer requirements.
SP1-142-001 0: OFF (default), 1: ON (Set at the time of customer requirements)
• Counter reset condition occurs fusing jam
1. Normal paper exit has been done during this continuous fusing jam, fusing jam counter is reset.
2. When "1" is changed to "0" SP1-142-001, to reset the
(SP9-912-001) fusing jam counter.
3. When after displaying SC559, SC release is made, reset the
(SP9912-001) fusing jam counter.
• Stripper plate float/ mounting failure
• Gear abrasion
• Fusing motor failure
1. Inspect or replace the stripper plate.
2. Replace the gears in the fusing unit or main machine.
3. Replace the fusing motor.
4. Replace the fusing unit.
SC No.
SC561-01
Type
A
Error Name/Error Condition/Major Cause/Solution
Pressure Roller Thermistor (Center) Disconnection
839
840
6. Troubleshooting
SC No.
SC561-05
SC No.
SC562-02
SC562-05
Type
D
Error Name/Error Condition/Major Cause/Solution
Pressure Roller Thermistor (Center) Disconnection (Low Power)
Below 0 degree C detected for 20 sec continuously.
Detection period 0.1 sec, detection count: 10 times or more.
• Non-contact thermistor disconnection
• Connector disconnected
• Harness disconnection in the fusing unit
• Harness disconnection between the fusing unit and the BCU or the
PSU (AC controller board)
• BCU defective
• Fusing lamp defective
• AC controller board defective
1. Check the power supply voltage and reconnect the cable to the outlet. (-05 only)
2. Reconnect the connectors (between the fusing unit and the BCU).
3. Replace the thermistor.
4. Replace the fusing unit.
5. Replace the harness between the fusing unit and the BCU or the PSU
(AC controller board).
6. Replace the BCU.
7. Replace the fusing sleeve belt unit.
8. Replace the PSU (AC controller board).
Type
A
D
Error Name/Error Condition/Major Cause/Solution
Pressure Roller Thermistor (Center) Does Not Reload
Pressure Roller Thermistor (Center) Does Not Reload (Low Power)
Service Call 501-584
SC No.
Type Error Name/Error Condition/Major Cause/Solution
Does not reach 40 degree C after fusing lamp 1ON for 12 sec.
• Outside input voltage guarantee
• Thermistor dirt
• Thermistor modification/float
• After excessive temperature rise prevention unit operation
• Fusing lamp disconnection
• Harness disconnection between the fusing unit and the BCU or the
PSU (AC controller board)
• Thermopile defective
• BCU defective
• AC controller board defective
1. Check the power supply voltage and reconnect the cable to the outlet.
2. Clean or replace the thermistor.
3. Replace the fusing sleeve thermostat.
4. Replace the fusing sleeve belt unit.
5. Replace the harness between the fusing unit and the BCU or the PSU
(AC controller board).
6. Replace the thermopile (center).
7. Replace the BCU.
8. Replace the PSU (AC controller board).
841
842
6. Troubleshooting
SC No.
SC563-00
Type
A
Error Name/Error Condition/Major Cause/Solution
Pressure Roller Thermistor (Center) High Temperature Detection
(software)
Above 230 degrees C detected for 1 sec continuously.
Detection period: 0.1 sec, detection count: 10 times or more.
• Paper setting misdetection
• Incorrect paper position in the paper feed tray
• Jammed paper between the center thermopile and fusing unit
• Thermopile lens dirt
• Thermopile modification/float
• Harness disconnection between the fusing unit and the BCU or the
PSU (AC controller board)
• Triac defective (short-circuit)
• BCU failure
• AC controller board failure
1. Check the paper settings.
2. Check the paper position in the paper feed tray.
3. Reconnect the connectors (main machine side, BCU side).
4. Remove the jammed paper between the center thermopile and fusing unit.
5. Clean or replace the thermopile (center).
6. Replace the harness between the fusing unit and the BCU or the PSU
(AC controller board).
7. Replace the BCU.
8. Replace the PSU (AC controller board).
If the problem cannot be solved after performing the above steps, replace the fusing unit.
Service Call 501-584
SC No.
SC564-00
Type
A
Error Name/Error Condition/Major Cause/Solution
Pressure Roller Thermistor (Center) High Temperature Detection
(Hardware)
Above 240 degrees C detected.
• Paper setting misdetection
• Incorrect paper position in the paper feed tray
• Jammed paper between the center thermopile and fusing unit
• Thermopile lens dirt
• Thermopile modification/float
• Pressure roller HP sensor disconnected
• Harness disconnection between the fusing unit and the BCU or the
PSU (AC controller board)
• Triac defective (short-circuit)
• BCU failure
• AC controller board failure
1. Check the paper settings.
2. Check the paper position in the paper feed tray.
3. Reconnect the connectors (main machine side, BCU side).
4. Remove the jammed paper between the center thermopile and fusing unit.
5. Clean or replace the thermopile (center).
6. Inspect the pressure roller HP sensor with SP5-803-047.
7. Replace the harness between the fusing unit and the BCU or the PSU
(AC controller board).
8. Replace the BCU.
9. Replace the PSU (AC controller board).
If the problem cannot be solved after performing the above steps, replace the fusing unit.
843
844
6. Troubleshooting
SC No.
SC569-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Paper Exit/ Pressure Release Motor Error Detection
Retry operation fails 3 times consecutively.
• Pressure roller HP sensor disconnected
• Pressure release encoder modification
• Fusing unit defective
• Paper exit/ pressure release motor disconnected
Inspect the pressure roller HP sensor with SP5-803-047.
If no response from the sensor, perform steps 1 and 2.
1. Check the connection of the pressure roller HP sensor.
2. Inspect the pressure roller HP sensor.
3. Inspect the pressure release encoder.
4. Replace the fusing unit.
5. Check the connectors of the paper exit/ pressure release motor.
SC No.
SC571-01
SC571-05
Type
A
D
Error Name/Error Condition/Major Cause/Solution
Pressure Roller Thermistor (Edge) Disconnection
Pressure Roller Thermistor (Edge) Disconnection (Low Power)
Service Call 501-584
SC No.
SC No.
SC572-04
SC572-05
Type Error Name/Error Condition/Major Cause/Solution
Below 0 degree C detected for 40 sec. continuously.
Detection period: 0.1 sec, detection counts: 10 times or more.
• Thermistor disconnection
• Connector disconnected
• Harness disconnection in the fusing unit
• Harness disconnection between the fusing unit and the BCU or the
PSU (AC controller board)
• BCU defective
• Fusing lamp defective
• AC controller board defective
1. Check the power supply voltage and reconnect the cable to the outlet. (-05 only)
2. Reconnect the connectors (between the fusing unit and the BCU or the PSU (AC controller board).
3. Replace the thermistor.
4. Replace the fusing unit.
5. Replace the harness between the fusing unit and the BCU or the PSU
(AC controller board).
6. Replace the BCU.
7. Replace the fusing sleeve belt unit.
8. Replace the PSU (AC controller board).
Type
A
D
Error Name/Error Condition/Major Cause/Solution
Pressure Roller Thermistor (Edge) Does Not Reload
Pressure Roller Thermistor (Edge) Does Not Reload ( Low Power)
845
846
6. Troubleshooting
SC No.
Type Error Name/Error Condition/Major Cause/Solution
After starting continuous job with paper width of 257mm or more, does not reach 0 degrees C after 100 sec.
• Outside input voltage guarantee
• Thermistor dirt
• Thermistor modification/float
• After excessive temperature rise prevention unit operation
• Fusing lamp disconnection
• Harness disconnection between the fusing unit and the BCU or the
PSU (AC controller board)
• Thermopile defective
• BCU defective
• AC controller board defective
1. Check the power supply voltage and reconnect the cable to the outlet.
2. Clean or replace the thermistor.
3. Replace the fusing sleeve thermostat.
4. Replace the fusing sleeve belt unit.
5. Reconnect or replace the harness between the fusing unit and the
BCU or the PSU (AC controller board).
6. Replace the thermopile (edge).
7. Replace the BCU.
8. Replace the PSU (AC controller board).
Service Call 501-584
SC No.
SC573-00
Type
A
Error Name/Error Condition/Major Cause/Solution
Pressure Roller Thermistor (Edge) High Temperature Detection (software)
Above 230 degrees C detected for 1 sec continuously.
Detection period: 0.1 sec, detection count: 10 times or more.
• Paper setting misdetection
• Incorrect paper position in the paper feed tray
• Jammed paper between the thermopile and fusing unit
• Thermopile lens dirt
• Thermopile modification/float
• Harness disconnection between the fusing unit and the BCU or the
PSU (AC controller board)
• Triac defective (short-circuit)
• BCU failure
• AC controller board failure
1. Check the paper settings.
2. Check the paper position in the paper feed tray.
3. Reconnect the connectors (main machine side, BCU side).
4. Remove the jammed paper between the thermopile and fusing unit.
5. Clean or replace the thermopile (edge).
6. Replace the harness between the fusing unit and the BCU or the PSU
(AC controller board).
7. Replace the BCU.
8. Replace the PSU (AC controller board).
If the problem cannot be solved after performing the above steps, replace the fusing unit.
847
6. Troubleshooting
848
SC No.
SC574-00
Type
A
Error Name/Error Condition/Major Cause/Solution
Pressure Roller Thermistor (edge) High Temperature Detection (hardware)
Above 240 degrees C detected
• Paper setting misdetection
• Incorrect paper position in the paper feed tray
• Jammed paper between the thermopile and fusing unit
• Thermopile lens dirt
• Thermopile modification/float
• Pressure roller HP sensor disconnected
• Harness disconnection between the fusing unit and the BCU or the
PSU (AC controller board)
• Triac defective (short-circuit)
• BCU failure
• AC controller board failure
1. Check the paper settings.
2. Check the paper position in the paper feed tray.
3. Reconnect the connector.
4. Remove the jammed paper between the thermopile and fusing unit.
5. Clean or replace the thermopile (edge).
6. Inspect the pressure roller HP sensor with SP5-803-047.
7. Replace the harness between the fusing unit and the BCU or the PSU
(AC controller board).
8. Replace the BCU.
9. Replace the PSU (AC controller board).
If the problem cannot be solved after performing the above steps, replace the fusing unit.
SC No.
SC581-01
SC581-05
Type
A
D
Error Name/Error Condition/Major Cause/Solution
Pressure Roller Thermistor (Full-bleed edge) Thermistor Disconnection
Pressure Roller Thermistor (Full-bleed edge) Disconnection (Low Power)
Service Call 501-584
SC No.
SC No.
SC582-04
SC582-05
Type Error Name/Error Condition/Major Cause/Solution
Below 0 degree C detected for 40 sec. continuously.
Detection period: 0.1 sec, detection count: 10 times or more.
• Thermistor disconnection
• Connector disconnected
• Harness disconnection in the fusing unit
• Harness disconnection between the fusing unit and the BCU or the
PSU (AC controller board)
• BCU defective
• Fusing lamp defective
• AC controller board defective
1. Check the power supply voltage and reconnect the cable to the outlet. (-05 only)
2. Reconnect the connectors (between the fusing unit and the BCU or the PSU (AC controller board).
3. Replace the thermistor.
4. Replace the fusing unit.
5. Replace the harness between the fusing unit and the BCU or the PSU
(AC controller board).
6. Replace the BCU.
7. Replace the fusing sleeve belt unit.
8. Replace the PSU (AC controller board).
Type
A
D
Error Name/Error Condition/Major Cause/Solution
Pressure Roller Thermistor (Full-bleed edge) Does Not Reload
Pressure Roller Thermistor (Full-bleed edge) Does Not Reload (Low
Power)
849
850
6. Troubleshooting
SC No.
Type Error Name/Error Condition/Major Cause/Solution
After starting continuous job with paper width of 257 mm or more, does not reach 0 degrees C after 100 sec.
• Outside input voltage guarantee
• Thermistor dirt
• Thermistor modification/float
• After excessive temperature rise prevention unit operation
• Fusing lamp disconnection
• Harness disconnection between the fusing unit and the BCU or the
PSU (AC controller board)
• Thermopile defective
• BCU defective
• AC controller board defective
1. Check the power supply voltage and reconnect the cable to the outlet.
2. Clean or replace the thermistor.
3. Replace the fusing sleeve thermostat.
4. Replace the fusing sleeve belt unit.
5. Replace the harness between the fusing unit and the BCU or the PSU
(AC controller board).
6. Replace the thermopile (edge).
7. Replace the BCU.
8. Replace the PSU (AC controller board).
Service Call 501-584
SC No.
SC583-00
Type
A
Error Name/Error Condition/Major Cause/Solution
Pressure Roller Thermistor (Full-bleed edge) High Temperature Detection
(software)
Above 230 degrees C detected for 1 sec continuously.
Detection period: 0.1 sec, detection count: 10 times or more.
• Paper setting misdetection
• Incorrect paper position in the paper feed tray
• Jammed paper between the thermopile and fusing unit
• Thermopile lens dirt.
• Thermopile modification/float
• Harness disconnection between the fusing unit and the BCU or the
PSU (AC controller board)
• Triac defective (short-circuit)
• BCU failure
• AC controller board failure
1. Check the paper settings.
2. Check the paper position in the paper feed tray.
3. Reconnect the connectors (main machine side, BCU side).
4. Remove the jammed paper between the thermopile and fusing unit.
5. Clean or replace the thermopile (edge).
6. Replace the harness between the fusing unit and the BCU or the PSU
(AC controller board).
7. Replace the BCU.
8. Replace the PSU (AC controller board).
If the problem cannot be solved after performing the above steps, replace the fusing unit.
851
852
6. Troubleshooting
SC No.
SC584-00
Type
A
Error Name/Error Condition/Major Cause/Solution
Pressure Roller Thermistor (Full-bleed edge) High Temperature Detection
(hardware)
Above 240 degrees C detected
• Paper setting misdetection
• Incorrect paper position in the paper feed tray
• Jammed paper between the thermopile and fusing unit
• Thermopile lens dirt
• Thermopile modification/float
• Pressure roller HP sensor disconnected
• Harness disconnection between the fusing unit and the BCU or the
PSU (AC controller board)
• Triac defective (short-circuit)
• BCU failure
• AC controller board failure
1. Check the paper settings.
2. Check the paper position in the paper feed tray.
3. Reconnect the connectors (main machine side, BCU side).
4. Remove the jammed paper between the thermopile and fusing unit.
5. Clean or replace the thermopile (edge).
6. Inspect the pressure roller HP sensor with SP5-803-047.
7. Replace the harness between the fusing unit and the BCU or the PSU
(AC controller board).
8. Replace the BCU.
9. Replace the PSU (AC controller board).
If the problem cannot be solved after performing the above steps, replace the fusing unit.
Service Call 620-687
SC No.
SC620-01
Type
D
Error Name/Error Condition/Major Cause/Solution
ADF Communication error 1 (DF3090 (D779)/ DF3100 (D3B0))
After ADF connection was recognized on startup, an error is detected.
(disconnection detection)
• ADF connection error
• ADF defection
• IPU board defection
• Noise contamination
Check if the SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Check if all connectors related to SPDF/ARDF are connected securely. Reconnect the connectors if they are disconnected, or loose.
2. Check the machine and ADF firmware version.
• Proceed to Step 3 if there is no new firmware released.
• Run the firmware update when there is a new firmware released.
3. Check the harness. Replace the harness if it is disconnected, or damaged.
4. Replace the IPU.
5. Check if there are any signs of a short circuit on the SPDF/ARDF
Main Board. If there are any defects, replace the board.
853
854
6. Troubleshooting
SC No.
SC620-02
SC No.
SC620-03
Type
D
Error Name/Error Condition/Major Cause/Solution
ADF Communication error 2 (DF3090 (D779)/ DF3100 (D3B0))
After ADF connection was recognized on startup, an error is detected.
(Retry out due to communication error)
• ADF connection error
• ADF defection
• IPU board defection
• Noise contamination
Follow the solution for SC620-01.
Type
D
Error Name/Error Condition/Major Cause/Solution
ADF Communication error 3 (DF3100 (D3B0))
SC is displayed when CIS initialization complete command is not received for certain time.
• ADF connection error
• ADF defection
• IPU board defection
• Noise contamination
• Unsupported ADF is connected
Check if the SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Check if all connectors related to SPDF/ARDF are connected securely. Reconnect the connectors if they are disconnected, or loose.
2. Check the harness. Replace the harness if it is disconnected, or damaged.
3. Check if there are any signs of a short circuit on the SPDF Main
Board. If there are any defects, replace the board.
Service Call 620-687
SC No.
SC621-00
SC No.
SC622-01
SC622-11
Type
D
Error Name/Error Condition/Major Cause/Solution
Finisher communication error
• Detected an error when connecting the communication line.
• Received a communication error notification from the URAT.
• Finisher control board defective.
• BCU defective
• IOB defective
• Connection error between finisher and main machine.
• Reconnect the Finisher interface cable.
• Replace the BCU.
• Replace the Imaging IOB.
• Replace the finisher.
• Turn the power off/on.
Type
D
D
Error Name/Error Condition/Major Cause/Solution
Paper bank 1 communication error for Paper Feed Unit PB3150 (D694)
Paper bank 1 communication error for Paper Feed Unit PB3220/
PB3210 (D787)
855
856
6. Troubleshooting
SC No.
SC No.
SC663-01
SC663-02
SC663-03
SC663-11
SC663-12
SC663-13
Type Error Name/Error Condition/Major Cause/Solution
• Detected an error when connecting the communication line.
• Received a communication error notification from the URAT.
• Paper bank control board defective
• BCU defective
• IOB defective
• Paper bank-main machine connection error
Check if the SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Check if all connectors in tray 1, 2, and optional paper tray are connected securely. Reconnect the connectors if they are disconnected, or loose.
2. Check the harness in tray 1, 2, and optional paper tray. Replace the harness if it is disconnected, or damaged.
3. Check if there are any signs of a short circuit on the Bank Main
Board. If there are any defects, replace the board.
D
D
D
Type
D
D
D
Error Name/Error Condition/Major Cause/Solution
Reset Detection: Imaging IOB: Software hang-up occurs
Reset Detection: Imaging IOB: Power ON reset occurs
Reset Detection: Imaging IOB: Software reset occurs
Reset Detection: Paper Transport IOB: Software hang-up occurs
Reset Detection: Paper Transport IOB: Power ON reset occurs
Reset Detection: Paper Transport IOB: Software reset occurs
Service Call 620-687
SC No.
SC No.
SC664-01
SC664-02
SC664-03
SC664-11
SC664-12
SC664-13
Type Error Name/Error Condition/Major Cause/Solution
SC is displayed when unexpected reset from Imaging IOB/Paper
Transport IOB is detected while standby/operation.
• Unexpected noise from inside the machine gets into Paper Transport
IOB.
• Parts defect and implementation defect of Imaging IOB/ Paper
Transport IOB.
• Software ran reset to ASIC when there was a bug in the software or unexpected signal was input (-03/-13 only).
1. Turn the main power OFF/ON.
2. Replace the Paper Transport IOB (-01 to -03)
3. Replace the Imaging IOB (-11 to -13)
D
D
D
D
D
Type
D
Error Name/Error Condition/Major Cause/Solution
VODKA1 (Paper Transport Vodka) access permission error to VODKA
SRAM
VODKA1 (Paper Transport Vodka) write error to VODKA SRAM
VODKA1 (Paper Transport Vodka) VODKA program launch error
VODKA2 (Imaging Vodka) access permission error to VODKA SRAM
VODKA2 (Imaging Vodka) write error to VODKA SRAM
VODKA2 (Imaging Vodka) VODKA program launch error
857
858
6. Troubleshooting
SC No.
SC No.
SC665-01
Type Error Name/Error Condition/Major Cause/Solution
The machine detects the communication error between VODKA and
SRAM when starting up, or recovery from energy saver mode.
The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• BCU
• Imaging IOB
• Paper Transport IOB
-01 to 03
1. Turn the main power OFF/ON.
2. Replace the Paper Transport IOB.
3. Replace the BCU.
4. Replace the Imaging IOB.
-11 to 13
1. Turn the main power OFF/ON.
2. Replace the Imaging IOB.
3. Replace the BCU.
Type
D
Error Name/Error Condition/Major Cause/Solution
Connection Error (BCU - IPU)
The machine detects the communication error between BCU and IPU (No
FFC connection) when starting up, or recovery from energy saver mode.
• FFC connection error
• FFC defective (disconnected, foreign object, etc.)
• The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• BCU
• IPU
1. Reconnect the FFC between BCU and IPU.
2. Replace the FFC between BCU and IPU.
3. Replace the BCU.
4. Replace the IPU.
Service Call 620-687
SC No.
SC665-02
SC No.
SC665-03
Type
D
Error Name/Error Condition/Major Cause/Solution
Connection Error (BCU – Imaging IOB)
The machine detects the communication error between BCU and Imaging
IOB (No connection) when starting up, or recovery from energy saver mode.
• FFC connection error
• FFC defective (disconnected, foreign object, etc.)
• The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• BCU
• Imaging IOB
1. Reconnect the FFC between BCU and Imaging IOB.
2. Replace the FFC between BCU and Imaging IOB.
3. Replace the BCU.
4. Replace the Imaging IOB.
Type
D
Error Name/Error Condition/Major Cause/Solution
Connection Error (Paper Transport IOB – Imaging IOB)
The machine detects the communication error between Imaging IOB and
Paper Transport IOB (No connection) when starting up, or recovery from energy saver mode.
• FFC connection error
• FFC defective (disconnected, foreign object, etc.)
• The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• Paper Transport IOB.
• Imaging IOB.
1. Reconnect the FFC between Paper Transport IOB and Imaging IOB.
2. Replace the FFC between Paper Transport IOB and Imaging IOB.
3. Replace the Imaging IOB.
4. Replace the Paper Transport IOB.
859
860
6. Troubleshooting
SC No.
SC665-04
Type
D
Error Name/Error Condition/Major Cause/Solution
IOB does not start up
The IOB does not start up when starting up, or recovery from energy saver mode.
• Connector disconnected
• Harness disconnected
• The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.)
• BCU
• Imaging IOB
• Paper Transport IOB
1. Turn the main power OFF/ON.
2. Reconnect the following FFC;
• BCU - Imagine IOB
• Imaging IOB - Paper Transport IOB
3. Replace the following FFC;
• BCU - Imagine IOB
• Imaging IOB - Paper Transport IOB
4. Replace the BCU.
5. Replace the Imaging IOB.
6. Replace the Paper Transport IOB.
Service Call 620-687
SC No.
SC665-05
Type
D
Error Name/Error Condition/Major Cause/Solution
Master Device Communication Error
The machine detects the communication error between CPU and Slave1 when starting up, or recovery from energy saver mode.
• FFC connection error
• FFC defective (disconnected, foreign object, etc.)
• The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• BCU
• IPU
• Imaging IOB
• Paper Transport IOB.
1. Turn the main power OFF/ON.
2. Reconnect the following FFC;
• BCU - Imagine IOB
• Imaging IOB - Paper Transport IOB
3. Replace the following FFC;
• BCU - Imagine IOB
• Imaging IOB - Paper Transport IOB
4. Replace the BCU.
5. Replace the Imaging IOB.
6. Replace the Paper Transport IOB.
861
862
6. Troubleshooting
SC No.
SC665-06
Type
D
Error Name/Error Condition/Major Cause/Solution
IPU and IOB signal Communication Error
The machine detects the communication error between CPU and Slave1 when starting up, or recovery from energy saver mode.
• FFC connection error
• FFC defective (disconnected, foreign object, etc.)
• The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• BCU
• IPU
• Imaging IOB
• Paper Transport IOB.
1. Turn the main power OFF/ON.
2. Reconnect the following FFC;
• BCU - Imagine IOB
• Imaging IOB - Paper Transport IOB
3. Replace the following FFC;
• BCU - Imagine IOB
• Imaging IOB - Paper Transport IOB
4. Replace the BCU.
5. Replace the IPU.
6. Replace the Imaging IOB.
7. Replace the Paper Transport IOB.
Service Call 620-687
SC No.
SC665-07
Type
D
Error Name/Error Condition/Major Cause/Solution
IPU signal Communication Error
The machine detects the communication error between CPU and Slave device when starting up, or recovery from energy saver mode.
• FFC connection error
• FFC defective (disconnected, foreign object, etc.)
• The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• BCU
• IPU
1. Turn the main power OFF/ON.
2. Reconnect the following FFC;
• BCU - Imagine IOB
• Imaging IOB - Paper Transport IOB
3. Replace the following FFC;
• BCU - Imagine IOB
• Imaging IOB - Paper Transport IOB
4. Replace the BCU.
5. Replace the IPU.
863
864
6. Troubleshooting
SC No.
SC665-08
Type
D
Error Name/Error Condition/Major Cause/Solution
IOB signal Communication Error
The machine detects the communication error between CPU and Slave1 when starting up, or recovery from energy saver mode.
• FFC connection error
• FFC defective (disconnected, foreign object, etc.)
• The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• BCU
• Imaging IOB
• Paper Transport IOB.
1. Turn the main power OFF/ON.
2. Reconnect the following FFC;
• BCU - Imagine IOB
• Imaging IOB - Paper Transport IOB
3. Replace the following FFC;
• BCU - Imagine IOB
• Imaging IOB - Paper Transport IOB
4. Replace the BCU.
5. Replace the Imaging IOB.
6. Replace the Paper Transport IOB.
Service Call 620-687
SC No.
SC665-11
Type
D
Error Name/Error Condition/Major Cause/Solution
Vodka1 Communication Error
The machine detects the communication error between CPU and Vodka1 when starting up, or recovery from energy saver mode.
• FFC connection error
• FFC defective (disconnected, foreign object, etc.)
• The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• BCU
• Paper Transport IOB.
1. Turn the main power OFF/ON.
2. Reconnect the FFC between Imaging IOB and Paper Transport IOB.
3. Replace the harness between Imaging IOB and Paper Transport
IOB.
4. Replace the Imaging IOB.
5. Replace the Paper Transport IOB.
6. Reconnect the FFC between BCU and Imaging IOB.
7. Replace the FFC between BCU and Imaging IOB
8. Replace the BCU.
865
866
6. Troubleshooting
SC No.
SC665-12
Type
D
Error Name/Error Condition/Major Cause/Solution
Vodka2 Communication Error
The machine detects the communication error between CPU and Vodka2 when starting up, or recovery from energy saver mode.
• FFC connection error
• FFC defective (disconnected, foreign object, etc.)
• The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• BCU
• Imaging IOB.
1. Turn the main power OFF/ON.
2. Reconnect the FFC between BCU and Imaging IOB.
3. Replace the FFC between BCU and Imaging IOB
4. Replace the BCU.
5. Replace the Imaging IOB.
6. Pull out all the PCUs and check if the SC reoccurs or not. If SC message disappears, replace the PCU.
7. Pull out all the toner bottles and check if the SC reoccurs or not. If SC message disappears, replace the toner bottle.
Service Call 620-687
SC No.
SC665-41
SC No.
SC665-42
Type
D
Error Name/Error Condition/Major Cause/Solution
Macaron1 Communication Error
The machine detects the communication error between CPU and
Macaron1 when starting up, or recovery from energy saver mode.
• FFC connection error
• FFC defective (disconnected, foreign object, etc.)
• The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• BCU
• IPU
1. Turn the main power OFF/ON.
2. Replace the IPU.
3. Reconnect the FFC between BCU and IPU.
4. Replace the FFC between BCU and IPU.
5. Replace the BCU.
Type
D
Error Name/Error Condition/Major Cause/Solution
Macaron2 Communication Error
The machine detects the communication error between CPU and
Macaron2 when starting up, or recovery from energy saver mode.
• FFC connection error
• FFC defective (disconnected, foreign object, etc.)
• The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• BCU
• IPU
1. Turn the main power OFF/ON.
2. Replace the IPU.
3. Reconnect the FFC between BCU and IPU.
4. Replace the FFC between BCU and IPU.
5. Replace the BCU.
867
868
6. Troubleshooting
SC No.
SC667-01
SC No.
SC667-10
Type
D
Error Name/Error Condition/Major Cause/Solution
Master Device Mode Setting Error
The machine detects the CPU mode error when starting up, or recovery from energy saver mode.
The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• BCU
1. Turn the main power OFF/ON.
2. Replace the BCU.
Type
D
Error Name/Error Condition/Major Cause/Solution
Slave1 Device Mode Setting Error
The machine detects the Slave1 mode error when starting up, or recovery from energy saver mode.
The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• BCU
• Paper Transport IOB
1. Turn the main power OFF/ON.
2. Replace the Paper Transport IOB.
3. Reconnect the FFC between Imaging IOB and Paper Transport IOB.
4. Replace the harness between Imaging IOB and Paper Transport
IOB.
5. Replace the Imaging IOB.
6. Reconnect the harness between BCU and Imaging IOB.
7. Replace the harness between BCU and Imaging IOB.
8. Replace the BCU.
Service Call 620-687
SC No.
SC667-11
SC No.
SC667-40
Type
D
Error Name/Error Condition/Major Cause/Solution
Slave2 Device Mode Setting Error
The machine detects the Slave2 mode error when starting up, or recovery from energy saver mode.
The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• BCU
• Paper Transport IOB
1. Turn the main power OFF/ON.
2. Replace the Imaging IOB.
3. Reconnect the harness between BCU and Imaging IOB.
4. Replace the harness between BCU and Imaging IOB.
5. Replace the BCU.
Type
D
Error Name/Error Condition/Major Cause/Solution
Macaron1 Mode Setting Error
The machine detects the Macaron1 mode error when starting up, or recovery from energy saver mode.
The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• BCU
• IPU
1. Turn the main power OFF/ON.
2. Replace the IPU.
3. Reconnect the harness between BCU and IPU.
4. Replace the harness between BCU and IPU.
5. Replace the BCU.
869
870
6. Troubleshooting
SC No.
SC667-41
SC No.
SC668-01
Type
D
Error Name/Error Condition/Major Cause/Solution
Macaron2 Mode Setting Error
The machine detects the Macaron2 mode error when starting up, or recovery from energy saver mode.
The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• BCU
• IPU
1. Turn the main power OFF/ON.
2. Replace the IPU.
3. Reconnect the harness between BCU and IPU.
4. Replace the harness between BCU and IPU.
5. Replace the BCU.
Type
D
Error Name/Error Condition/Major Cause/Solution
Vodka1 Version Setting Error
The machine detects the version settings error in Vodka1 when starting up, or recovery from energy saver mode.
The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• BCU
• Paper Transport IOB
1. Turn the main power OFF/ON.
2. Replace the Paper Transport IOB.
3. Replace the BCU.
Service Call 620-687
SC No.
SC668-02
SC No.
SC668-03
SC No.
SC669-**
SC669-01
SC669-02
Type
D
Error Name/Error Condition/Major Cause/Solution
Vodka2 Version Setting Error
The machine detects the version settings error in Vodka2 when starting up, or recovery from energy saver mode.
The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• BCU
• Imaging IOB
1. Turn the main power OFF/ON.
2. Replace the Imaging IOB.
3. Replace the BCU.
Type
D
Error Name/Error Condition/Major Cause/Solution
Vodka1,2 Version Setting Error
The machine detects the version settings error in both Vodka 1 and
Vodka2 when starting up, or recovery from energy saver mode.
The following board defects (Parts implementation defect, solder scrap, implemented parts defect, etc.);
• BCU
• Imaging IOB
• Paper Transport IOB
1. Turn the main power OFF/ON.
2. Replace the BCU.
3. Replace the Imaging IOB.
4. Replace the Paper Transport IOB.
Type
D
D
Error Name/Error Condition/Major Cause/Solution
EEPROM Communication Error
EEPROM OPEN: ID error
EEPROM OPEN: Channel error
871
872
6. Troubleshooting
SC669-09
SC669-10
SC669-11
SC669-12
SC669-13
SC669-14
SC669-15
SC669-16
SC No.
SC669-03
SC669-04
SC669-05
SC669-06
SC669-07
SC669-08
SC669-17
SC669-18
SC669-19
SC669-20
SC669-21
SC669-22
SC669-23
SC669-24
SC669-25
SC669-26
SC669-36
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
Type
D
D
D
D
D
D
D
D
Error Name/Error Condition/Major Cause/Solution
EEPROM OPEN: Device error
EEPROM OPEN: Communication abort error
EEPROM OPEN: Communication timeout error
EEPROM OPEN: Operation stopped error
EEPROM OPEN: Buffer full
EEPROM OPEN: No error code
EEPROM CLOSE: ID error
EEPROM CLOSE: No error code
EEPROM Data write: ID error
EEPROM Data write: Channel error
EEPROM Data write: Device error
EEPROM Data write: Communication abort error
EEPROM Data write: Communication timeout error
EEPROM Data write: Operation stopped error
EEPROM Data write: Buffer full
EEPROM Data write: No error code
EEPROM Data read: ID error
EEPROM Data read: Channel error
EEPROM Data read: Device error
EEPROM Data read: Communication abort error
EEPROM Data read: Communication timeout error
EEPROM Data read: Operation stopped error
EEPROM Data read: Buffer full
EEPROM Data read: No error code
Verification error
Service Call 620-687
SC No.
SC669-37
Type
D
Error Name/Error Condition/Major Cause/Solution
Error Detection
The TD sensor cannot be recovered after retrying N*1 times for EEPROM communication error.
(*1 SC669-01 to 26: 3, SC669-36: 2, SC669-37: 1)
• Electrical noise
• EEPROM not connected fully
• EEPROM not installed
• EEPROM damaged
• BCU damaged
1. Turn the main power OFF/ON.
2. Reconnect the EEPROM.
3. Replace the EEPROM.
4. Replace the BCU.
873
6. Troubleshooting
874
SC No.
681-**
Type
D
Error Name/Error Condition/Major Cause/Solution
Toner bottle: ID Chip Communication error
When error notification was received during communication with the tag and operation is not resumed after N*1 retries.
*1 See the detailed table below.
• Corrupted ID data
• Disconnected ID chip
• No ID chip
• Noise
Turn the main power off, and then do the following.
1. Clean ID chip connections inside the toner bottle, and check if any of the ID Chip Contact Board connector pins have snapped. If there are any snapped pin, follow step 5.
2. Reconnect the connectors between Imaging IOB and ID Chip
Contact Board.
3. Reconnect the FFC between Imaging IOB and BCU.
4. Replace the ID Chip Contact Board.
5. Reconnect the harness between Imaging IOB and ID Chip Contact
Board.
6. Replace the FFC between Imaging IOB and BCU.
7. Replace the Imaging IOB.
8. Replace the BCU.
SC681 Details
No.
Detail
01 - 04 Invalid device ID
06 - 09 Channel error
11 - 14 Device Error
16 - 19 Communication error (interrupted)
21 - 24 Communication timeout
Causes
Noise, Incorrect connection, Malfunction
Noise, Incorrect connection, Malfunction
Noise, Incorrect connection
Noise, Incorrect connection
Noise, Incorrect connection, Malfunction
3
3
3
3
3
Retry
No.
Detail
26 - 29 Device stops
(logically)
31 - 34 Full of buffer
(request)
36 - 39 Verification error
Causes
Noise, Incorrect connection, Malfunction
Noise, Incorrect connection, Malfunction
Noise, Incorrect connection
• If the last digit of the SC’s branch number (-**) is:
1 or 6, then do the above steps for K
2 or 7, then do the above steps for M
3 or 8, then do the above steps for C
4 or 9, then do the above steps for Y
Service Call 620-687
3
2
3
Retry
875
876
6. Troubleshooting
No.
SC682-**
Type
D
Error Name/Error Condition/Major Cause/Solution
TD sensor communication error
TD sensor cannot be recovered after retrying N*1 times for an ID chip communication error.
*1 See the detailed table below.
• Corrupted ID data
• Disconnected ID chip
• No ID chip
• Noise
Turn the main power off, and then do the following.
1. Reinstall the PCU.
2. Reconnect the connectors between Imaging IOB and TD sensor.
3. Reconnect the FFC between Imaging IOB and BCU.
4. Replace the PCU.
5. Reconnect the harness between Imaging IOB and TD sensor.
6. Replace the FFC between Imaging IOB and BCU.
7. Replace the Imaging IOB.
8. Replace the BCU.
SC682 Details
No.
Description
01 - 04 Invalid device ID
06 - 09 Channel error
11 - 14 Device Error
• If the last digit of the SC’s branch number (-**) is:
1 or 6, then do the above steps for K
2 or 7, then do the above steps for M
3 or 8, then do the above steps for C
4 or 9, then do the above steps for Y
Cause
Noise, Incorrect connection, Malfunction
Noise, Incorrect connection, Malfunction
Noise, Incorrect connection
Retry
3
3
3
Service Call 620-687
No.
Description
16 - 19 Communication error
(interrupted)
21 - 24 Communication timeout
26 - 29 Device stops (logically)
31 - 34 Full of buffer (request)
36 - 39 Verification error
Cause
Noise, Incorrect connection
Noise, Incorrect connection, Malfunction
Noise, Incorrect connection, Malfunction
Noise, Incorrect connection, Malfunction
Noise, Incorrect connection
SC No.
SC687-00
Type
D
Error Name/Error Condition/Major Cause/Solution
PER Not Received Error
Unable to receive the PER command from the controller.
Communication error
Replace the BCU.
Retry
3
3
2
3
3
SC No.
SC632-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Counter device error 1
After 3 attempts to send a data frame to the optional counter device via the serial communication line, no ACK signal was received within 100 ms.
Serial line between the optional counter device, the relay board and copier control board is disconnected or damaged.
• Turn the main power off/on.
• Check the serial communication line.
877
878
6. Troubleshooting
SC No.
SC633-00
SC No.
SC634-00
SC No.
SC635-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Counter device error 2
After communication was established, the controller received the brake signal from the accounting device.
Serial line between the optional counter device, the relay board and copier control board is disconnected or damaged.
• Turn the main power off/on.
• Check the serial communication line.
Type
D
Error Name/Error Condition/Major Cause/Solution
Counter device error 3
A backup RAM error was returned by the counter device.
Counter device control board or the backup battery of counter device defective
• Replace the counter device control board.
• Replace the backup battery.
Type
D
Error Name/Error Condition/Major Cause/Solution
Counter device error 4
A backup battery error was returned by the counter device.
Counter device control board or the backup battery of counter device defective
• Replace the counter device control board.
• Replace the backup battery.
Service Call 620-687
SC No.
SC636-01
SC No.
SC636-02
Type
D
Error Name/Error Condition/Major Cause/Solution
IC Card Error (Expanded authentication module error)
Issued when expanded authentication management is set to "ON" but either of the following occur.
• There is no expanded authentication module in the machine.
• The SD card or the file of the expanded authentication module is broken.
• There is no DESS module in the machine.
• There is no DESS module in the machine (models on which the function is optional).
• There is no expanded authentication module in the machine.
• The SD card or the file of the expanded authentication module is broken.
• Set a working SD card/expanded authentication module file.
• Install the DESS module.
• In the SSP mode set SP5-401-160 to "0".
• In the SSP mode, set SP5-401-161 to "0".
• Replace the NVRAM.
Type
D
Error Name/Error Condition/Major Cause/Solution
IC Card Error (Version error)
The version of the expanded authentication module is not correct.
Incorrect module version
Install the correct file of the expanded authentication module.
879
880
6. Troubleshooting
SC No.
SC637-01
SC No.
SC637-02
SC No.
SC641-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Tracking Information Notification Error (Tracking application error)
Tracking information was lost.
• Tracking SDK application error
• Internal notification error
Turn the main power off/on.
Type
D
Error Name/Error Condition/Major Cause/Solution
Tracking Information Notification Error (Management server error)
Tracking information was lost.
Communication with tracking management server failed.
• Network error
• tracking management server error
• Tracking SDK application error
Turn the main power off/on.
Type
D
Details (Symptom, Possible Cause, Troubleshooting Procedures)
Communication error between BCU and Controller board.
Controller board does not respond after BCU tries to communicate three times.
• Controller board software error
• Connect error between BCU and Controller board
• Engine board software error
• Check connections between Controller board and BCU.
• Turn the main switch off and on.
Service Call 620-687
SC No.
SC650-01
SC No.
SC650-04
Type
C
Error Name/Error Condition/Major Cause/Solution
Remote Service Modem Communication Error (Dialup authentication failure)
• An error related to communication (dialup connection, modem board etc.) using the RC Gate Type M was detected or an error that prevents RC Gate operation was detected at power on.
• Displayed only when an error is detected while RC Gate is operating.
• SC is not issued if an error occurs during RC Gate installation
(because it can be referenced using SP).
Dialup authentication failure
Check the following SPs.
• SP5-816-156
• SP5-816-157
Type
C
Error Name/Error Condition/Major Cause/Solution
Remote Service Modem Communication Error (dialup failing because of incorrect modem configuration)
• An error related to communication (dialup connection, modem board etc.) using the RC Gate Type M was detected or an error that prevents RC Gate operation was detected at power on.
• Displayed only when an error is detected while RC Gate is operating.
• SC is not issued if an error occurs during RC Gate installation
(because it can be referenced using SP).
Dialup failing because of incorrect modem configuration
Check if the setting of SP5-816-160 is correct.
If it is correct, then there is a software bug.
881
882
6. Troubleshooting
SC No.
SC650-05
SC No.
SC650-13
Type
C
Error Name/Error Condition/Major Cause/Solution
Remote Service Modem Communication Error (insufficient current or connection error)
• An error related to communication (dialup connection, modem board etc.) using the RC Gate Type M was detected or an error that prevents RC Gate operation was detected at power on.
• Displayed only when an error is detected while RC Gate is operating.
• SC is not issued if an error occurs during RC Gate installation
(because it can be referenced using SP).
Insufficient current or connection error
The line is not supported and nothing can be done.
Type
C
Error Name/Error Condition/Major Cause/Solution
Remote Service Modem Communication Error (RC Gate Type M was installed but modem is not present (detected during operation))
• An error related to communication (dialup connection, modem board etc.) using the RC Gate Type M was detected or an error that prevents RC Gate operation was detected at power on.
• Displayed only when an error is detected while RC Gate is operating.
• SC is not issued if an error occurs during RC Gate installation
(because it can be referenced using SP).
RC Gate Type M was installed but modem is not present (detected during operation)
• If a modem board is not installed, install it.
• Check again if the modem driver configurations (SP5-816-160,
SP5-816-165 to 171) are correct.
• If the problem is not solved, replace the modem.
Service Call 620-687
SC No.
SC650-14
SC No.
SC651-01
SC No.
SC651-02
Type
C
Error Name/Error Condition/Major Cause/Solution
Remote Service Modem Communication Error (RC Gate Type N was installed but modem is present or wired/wireless LAN is not working correctly)
• An error related to communication (dialup connection, modem board etc.) using the RC Gate was detected or an error that prevents RC Gate operation was detected at power on.
• Displayed only when an error is detected while RC Gate is operating.
• SC is not issued if an error occurs during RC Gate installation
(because it can be referenced using SP).
RC Gate Type N was installed but modem is present or wired/wireless
LAN is not working correctly
• If a modem board is attached, remove it.
• Check if wired/wireless LAN works.
Type
C
Error Name/Error Condition/Major Cause/Solution
Illegal Remote Service Dial-up (Chat program parameter error)
An unexpected error occurred when RC Gate Type M dialed up the NRS
Center.
Software bug
Logging only.
Type
C
Error Name/Error Condition/Major Cause/Solution
Illegal Remote Service Dial-up (Chat program execution error)
An unexpected error occurred when RC Gate dialed up the NRS Center.
Software bug
Logging only.
883
884
6. Troubleshooting
SC No.
SC652-00
SC No.
SC653-00
Type
A
Error Name/Error Condition/Major Cause/Solution
Remote service ID2 mismatching
There was an authentication mismatch between ID2 for @Remote, the controller board, and NVRAM.
• Used controller board installed
• Used NVRAM installed (such action is not allowed.)
• If this occurs during RC Gate installation:
Check the validity of the certificate and the NVRAM, check the machine serial number, write the common certificate, and then begin installation again.
• If this occurs after RC Gate installation:
Clear the RC Gate install status, check the validity of the certificate and the NVRAM, check the machine serial number, write the common certificate, and then begin installation again.
Type
A
Error Name/Error Condition/Major Cause/Solution
Incorrect remote service ID2
ID2 stored in the NVRAM has either of the following problems.
• Number of characters is not 17.
• Includes a character that cannot be printed.
• All spaces
• NULL
Replace the NVRAM.
Clear the RC Gate install status, write the common certificate, and then begin installation again.
Service Call 620-687
SC No.
SC670-01
SC No.
SC670-02
Type
D
Error Name/Error Condition/Major Cause/Solution
Engine start up error when the machine boots up
• /ENGRDY signal was not asserted when the machine was turned on.
• PCI I/F is not linked up when the machine returns from energy saver mode.
• /IPURDY signal was not asserted when the machine was turned on or returned from energy saver mode.
• EC/PC/SC response was not received within specified time from power on.
• Writing to Rapi driver failed (the other party not found through PCI).
• Connection defect between controller board and IPU.
• IPU is down / unstable
• BCU is down / unstable
Engine board does not start up.
Refer to page 977 "When SC670 (Engine start up error) is displayed".
Type
D
Error Name/Error Condition/Major Cause/Solution
Engine start up error when the machine is in operation
• CPU reset by software
• CPU reset by anomaly CPU
• CPU reset by hardware defect / noise
• Hardware defect
Engine board reset unexpectedly.
Refer to page 977 "When SC670 (Engine start up error) is displayed".
885
6. Troubleshooting
SC672
RTB 34
SC No.
SC670-03
SC No.
SC670-04
SC No.
SC672-10
Type
D
Error Name/Error Condition/Major Cause/Solution
IPU start up error when the machine boots up
VDET_EPCI signal was not asserted when the machine was turned on.
• IPU, PSU, and/or CTL defective
• Incorrect connection between CTL and IPU.
• Harness of IPU disconnected
Refer to page 977 "When SC670 (Engine start up error) is displayed".
Type
D
Error Name/Error Condition/Major Cause/Solution
Communication error between the engine and controller
Communication could not linked up.
• IPU and/or CTL defective
• Incorrect connection between CTL and IPU.
Refer to page 977 "When SC670 (Engine start up error) is displayed".
Type
D
Error Name/Error Condition/Major Cause/Solution
Controller start up error
After the machine was powered on, communication between the controller and the operation panel was not established.
• Controller stalled
• Board installed incorrectly
• Controller board defective
• Operation panel connector loose, broken, or defective
• Controller late
Refer to page 978 "When SC672 (Controller start up error) Is
886
Service Call 620-687
SC No.
SC672-11
SC No.
SC672-12
Type
D
Error Name/Error Condition/Major Cause/Solution
Controller start up error
After the machine was powered on, communication between the controller and the operation panel was not established, or communication with controller was interrupted after a normal startup.
• Controller stalled
• Board installed incorrectly
• Controller board defective
• Operation panel connector loose, broken, or defective
• Controller late
Refer to page 978 "When SC672 (Controller start up error) Is
Type
D
Error Name/Error Condition/Major Cause/Solution
Controller start up error
Communication with controller was interrupted after a normal startup.
• Controller stalled
• Board installed incorrectly
• Controller board defective
• Operation panel connector loose, broken, or defective
• Controller late
Refer to page 978 "When SC672 (Controller start up error) Is
887
888
6. Troubleshooting
SC No.
SC672-13
SC No.
SC672-99
Type
D
Error Name/Error Condition/Major Cause/Solution
Controller start up error
The operation panel detects that the controller is down due to other reason shown in SC672-10, SC672-11, and SC672-12.
• Controller stalled
• Board installed incorrectly
• Controller board defective
• Operation panel connector loose, broken, or defective
• Controller late
Refer to page 978 "When SC672 (Controller start up error) Is
Type
D
Error Name/Error Condition/Major Cause/Solution
Controller start up error
The operation panel software ended abnormally.
• Controller stalled
• Board installed incorrectly
• Controller board defective
• Operation panel connector loose, broken, or defective
• Controller late
Refer to page 978 "When SC672 (Controller start up error) Is
Service Call 620-687
SC No.
SC673-10
Type
D
Error Name/Error Condition/Major Cause/Solution
Operation panel Flair communication error (Smart Operation Panel)
This SC is issued only for the machine that has the Smart Operation Panel installed.
• Communication between Smart Operation Panel and main machine
(this is called "Flair communication") is not sent to Smart Operation
Panel.
• SP setting (SP5-748-201) for Smart Operation Panel is not activated.
The CATS module (controller) did not see the response to notification of monitoring service module (operation panel).
• Turn the main power OFF/ON.
• Set SP5-748-201 (OpePanel Setting: Cheetah Panel Connect
Setting) to "1: Connect" if the value is "0: Not connect".
889
890
6. Troubleshooting
Type SC No.
SC700
SC700-01
SC700-02
SC700-04
SC700-05
SC700-06
SC700-07
SC700-09
D
D
D
D
D
D
D
Error Name/Error Condition/Major Cause/Solution
SPDF DF3100 (D3B0) Error
ADF bottom plate lift motor error
ADF pick-up roller lift motor
ADF feed motor error
ADF entrance motor error
ADF transport motor error
ADF scanning motor error
ADF exit motor error
-01
Even if the base plate motor is rotated in the base plate ascent direction, the base plate paper feed correct position sensor does not detect.
Even if the base plate motor is rotated in the base plate descent direction, the base plate home position sensor does not detect.
-02
Even if the pickup arm motor is rotated, the pickup arm home position sensor does not detect.
-04, 05, 06, 07, 09
When an error notification signal is detected during the motor drive period.
Service Call 700-792
SC No.
SC No.
SC701
Type Error Name/Error Condition/Major Cause/Solution
-01
• Base plate paper feed correct position sensor error (output error)
• Base plate home position sensor error (output error)
• Base plate motor error (does not rotate)
• Controller error
-02
• Pick-up home position sensor error (output error)
• Pick-up motor error (does not rotate)
• Controller error
-04, 05, 06, 07, 09
• Motor defective
• Connector disconnected
• Harness broken
• Overload
Check if the SC occurs by turning the main power OFF then ON, opening/closing covers, and input/output check. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
The target parts that need to be checked are as follows;
• -01: all motors, and Pick-up Roller HP Sensor
• -02: all motors, and Bottom Plate Lift Sensor, Bottom Plate HP Sensor
• -03, 04, 05, 06, 07, 09: all parts in ADF.
1. Check if the connector of the target part is connected securely.
Reconnect the connector if it is disconnected, or loose.
2. Check the harness for the target part. Replace the harness if it is disconnected, or damaged.
3. Check if the motor runs, sensors turn OFF/ON, has no overloads, and is properly driven. Replace the parts if there are any defects.
4. Check if there are any signs of a short circuit. Replace the parts if there are any defects.
Type Error Name/Error Condition/Major Cause/Solution
ARDF DF3090 (D779) Error
891
892
6. Troubleshooting
SC No.
SC701-03
SC701-08
SC No.
SC702
Type
D
D
Error Name/Error Condition/Major Cause/Solution
Paper Feed Motor Driver Error
Detection of error signal from motor driver
Paper Exit Motor Driver Error
Detection of error signal from motor driver.
• Encoder disconnection
• Encoder connector dropout
• Encoder defective
• Overload
• Motor deterioration
Check if the SC occurs by turning the main power OFF then ON, opening/closing covers, and input/output check. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
• The target parts that need to be checked are all motors, all solenoids, all clutches, and all sensors.
1. Check if the connector of the target part is connected securely.
Reconnect the connector if it is disconnected, or loose.
2. Check the harness for the target part. Replace the harness if it is disconnected, or damaged.
3. Check if the motor runs, sensors turn OFF/ON, has no overloads, and is properly driven. Replace the parts if there are any defects.
4. Check if there are any signs of a short circuit. Replace the parts if there are any defects.
Type Error Name/Error Condition/Major Cause/Solution
ARDF DF3090 (D779) Error
Service Call 700-792
SC No.
SC702-01
Type
D
Error Name/Error Condition/Major Cause/Solution
Protection Device Intercept Error
When original source 5V power supply is ON, protection device intercept of 24V power supply system is detected.
Any of feed motor, transport motor, reverse solenoid, paper feed solenoid, paper feed clutch and FAN motor defective, a harness shortcircuit occurs, and the protection device of the 24V power supply system intercepts.
Check if the SC occurs by turning the main power OFF then ON, opening/closing covers, and input/output check. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
• The target parts that need to be checked are all motors, all solenoids, and all clutches.
1. Check if the connector of the target part is connected securely.
Reconnect the connector if it is disconnected, or loose.
2. Check the harness for the target part. Replace the harness if it is disconnected, or damaged.
3. Check if the specific part runs (OUTPUT Check), has no overloads, and is properly driven. Replace the part if there are any defects.
4. Check if there are any signs of a short circuit. Replace the parts if there are any defects.
893
894
6. Troubleshooting
SC No.
SC702-02
Type
D
Error Name/Error Condition/Major Cause/Solution
Protection Device Intercept Error 2
When original source 5V power supply is ON, protection device intercept of 24V OUT power supply system is detected.
Solenoid defective or harness short-circuit occurs in 24VOUT power supply system.
Check if the SC occurs by turning the main power OFF then ON, opening/closing covers, and input/output check. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
• The target parts that need to be checked are all motors, all solenoids, and all clutches.
1. Check if the connector of the target part is connected securely.
Reconnect the connector if it is disconnected, or loose.
2. Check the harness for the target part. Replace the harness if it is disconnected, or damaged.
3. Check if the specific part runs (OUTPUT Check), has no overloads, and is properly driven. Replace the part if there are any defects.
4. Check if there are any signs of a short circuit. Replace the parts if there are any defects.
Service Call 700-792
SC No.
SC702-03
SC No.
SC702
Type
D
Error Name/Error Condition/Major Cause/Solution
Protection Device Intercept Error 3
When original source 5V power supply is ON, protection device intercept of 5VE power supply system is detected.
Sensor defective or a harness short-circuit occur in 5VE power supply system.
Check if the SC occurs by turning the main power OFF then ON, opening/closing covers, and input/output check. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Check if the connector for Original Set Sensor is connected securely. Reconnect the connector if it is disconnected, or loose.
2. Check the harness for Original Set Sensor. Replace the harness if it is disconnected, or damaged.
3. Check if the Original Set Sensor turns OFF/ON (INPUT Check).
Replace the part if there are any defects.
4. Check if there are any signs of a short circuit. Replace the parts if there are any defects.
Type Error Name/Error Condition/Major Cause/Solution
ARDF/SPDF Error
895
896
6. Troubleshooting
SC No.
SC702-04
SC702-05
Type
D
D
Error Name/Error Condition/Major Cause/Solution
Protection Device Intercept Error 4
Motor defective in any of the pickup motor, completion stamp, base plate motor or FAN motor, or a harness short-circuit occurs, and the protection device of the non-interlocking power supply system intercepts.
Motor defective or a harness short-circuit occurs in the non-interlocking power supply system.
Check if the SC occurs by turning the main power OFF then ON, opening/closing covers, and input/output check. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
• The target parts that need to be checked are the Pick-up Roller Lift
Motor, Stamp Solenoid, Feed Motor, and Cooling Fan Motor.
1. Check if the connector of the target part is connected securely.
Reconnect the connector if it is disconnected, or loose.
2. Check the harness for the target part. Replace the harness if it is disconnected, or damaged.
3. Check if the motor runs, has no overloads, and is properly driven.
Replace the parts if there are any defects.
4. Check if there are any signs of a short circuit. Replace the parts if there are any defects.
Protection Device Intercept Error 5
Service Call 700-792
SC No.
SC No.
SC721
SC721-03
SC721-06
SC721-10
SC721-11
Type Error Name/Error Condition/Major Cause/Solution
Motor defective in the paper feed motor, pullout motor, intermediate motor, scanner motor or paper exit motor, or a harness short-circuit occurs, and the protection device of the interlocking power supply system intercepts.
Motor defective or a harness short-circuit occurs in the interlocking power supply system.
Check if the SC occurs by turning the main power OFF then ON, opening/closing covers, and input/output check. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
• The target parts that need to be checked are the Feed Motor, Pickup Roller Lift Motor, Relay Motor, Transport Motor, and Exit Motor.
1. Check if the connector of the target part is connected securely.
Reconnect the connector if it is disconnected, or loose.
2. Check the harness for the target part. Replace the harness if it is disconnected, or damaged.
3. Check if the motor runs, has no overloads, and is properly driven.
Replace the parts if there are any defects.
4. Check if there are any signs of a short circuit. Replace the parts if there are any defects.
Type
B
C
B
B
Error Name/Error Condition/Major Cause/Solution
Booklet Finisher SR3220 (D3B9) Error
Protection Device Intercept Error 1
Fuse blowout is detected
See the descriptions next table below.
Transport Motor 1 Error
Motor driver detects an error state (DC motor control error) (1st time is jam notification, 2nd time is SC notification).
Transport Motor 2 Error
Motor driver detects an error state (DC motor control error) (1st time is jam notification, 2nd time is SC notification).
897
898
6. Troubleshooting
SC No.
SC721-17
SC721-24
SC721-25
SC721-27
SC721-28
SC721-30
SC721-33
SC721-41
B
B
B
B
B
Type
B
B
B
Error Name/Error Condition/Major Cause/Solution
Paper Eject Motor 2 Error
Motor driver detects an error state (DC motor control error) (1st time is jam notification, 2nd time is SC notification).
Paper Exit Guide Plate Open/Close motor Error
• During movement to home, the home position could not be detected within a predetermined pulse (1st time is jam notification, 2nd time is
SC notification).
• During movement from home, the home position was detected for longer than a predetermined pulse (1st time is jam notification, 2nd time is SC notification).
Punch Drive Motor Error
• During movement to home, the home position could not be detected within a predetermined time (1st time is jam notification, 2nd time is
SC notification).
• During movement from home, the home position was detected even after a predetermined time elapsed (1st time is jam notification, 2nd time is SC notification).
• Output from the encoder could not be counted for a predetermined number of times within a predetermined time (1st time is jam notification, 2nd time is SC notification).
Punch Movement Motor Error
Punch Horizontal Registration Detection Error
Jogger Motor 1 Error
Positioning Roller Motor Error
Release Motor Error
• During movement to home, the home position could not be detected within a predetermined pulse (1st time is jam notification, 2nd time is
SC notification).
• During movement from home, the home position was detected even after a predetermined pulse elapsed (1st time is jam notification,
2nd time is SC notification).
Service Call 700-792
SC No.
SC721-42
SC721-44
SC721-52
Type
B
B
B
Error Name/Error Condition/Major Cause/Solution
Stapler Retreat Motor Error
• During movement to home, the home position could not be detected within a predetermined pulse (1st time is jam notification, 2nd time is
SC notification).
• During movement from home, the home position was detected even after a predetermined pulse elapsed (1st time is jam notification,
2nd time is SC notification).
• During movement from home, retreat sensor ON could not be detected even after a predetermined pulse elapsed (1st time is jam notification, 2nd time is SC notification).
• During initialization, retreat sensor ON was detected simultaneously when the home position is detected (1st time is jam notification, 2nd time is SC notification).
Stapler Motor Error
• During movement to home, the home position could not be detected even after a predetermined time elapsed (1st time is jam notification,
2nd time is SC notification).
• During movement from home, the home position was detected even after a predetermined time elapsed (1st time is jam notification, 2nd time is SC notification).
• During motor drive, the output from the encoder could not be counted for a predetermined number of times within a predetermined time (1st time is jam notification, 2nd time is SC notification).
Folding Plate Drive Motor Error
• Motor driver detects an error (short-circuit and overheating) (1st time is SC).
• During movement to home, the home position could not be detected within a predetermined pulse (1st time is jam notification, 2nd time is
SC notification).
• During movement from home, the home position was detected for longer than a predetermined pulse (1st time is jam notification, 2nd time is SC notification).
899
900
6. Troubleshooting
SC No.
SC721-53
SC721-58
SC721-59
SC721-80
SC721-70
Type
B
B
B
B
B
Error Name/Error Condition/Major Cause/Solution
Rear End Fence Displacement Motor Error
• During movement to home, the home position could not be detected within a predetermined pulse (1st time is jam notification, 2nd time is
SC notification).
• During movement from home, the home position was detected for longer than a predetermined pulse (1st time is jam notification, 2nd time is SC notification).
Bundle Transport 1 Release Motor Error
Bundle Transport 2 Release Motor Error
• During movement to home, the home position could not be detected within a predetermined pulse (1st time is jam notification, 2nd time is
SC notification).
• During movement from home, the home position was detected for longer than a predetermined pulse (1st time is jam notification, 2nd time is SC notification).
Folding Transport Motor Error
• Motor driver detects an error (short-circuit or overheating) (1st time is SC)
Tray 1 Lift Motor Error
• Motor driver detects an error (short-circuit or overheating) (1st time is SC).
• During descent, the paper surface sensor still detects paper even after a predetermined time elapses (1st time is jam notification, 2nd time is SC notification).
• During ascent, the paper surface sensor could not detect the paper surface even after a predetermined time elapses (1st time is jam notification, 2nd time is SC notification).
Service Call 700-792
SC No.
SC721-71
SC721-81
Type
B
B
Error Name/Error Condition/Major Cause/Solution
Shift Motor 1 Error
• During movement to home, the home position could not be detected within a predetermined pulse (1st time is jam notification, 2nd time is
SC notification).
• During movement from home, the home position was detected for longer than a predetermined pulse (1st time is jam notification, 2nd time is SC notification).
Paper Guide Drive Motor Error
• During movement to home, the home position could not be detected within a predetermined pulse (1st time is jam notification, 2nd time is
SC notification).
• During movement from home, the home position was detected for longer than a predetermined pulse (1st time is jam notification, 2nd time is SC notification).
901
902
6. Troubleshooting
SC No.
SC No.
SC721
SC721-06
Type Error Name/Error Condition/Major Cause/Solution
• Overcurrent (-03 only)
• Staple jam (-44 only)
• Encoder error (-11, -11, -25, -44)
• Motor defective
• Connecter disconnected, or loose
• Motor overload
• HP sensor defective
• Paper surface sensor defective (-70 only)
Check if the SC occurs by opening/closing covers, and input/output check. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
• The target parts are the motor and related HP sensor that SC occurred.
1. Check if the connector of the target part is connected securely.
Reconnect the connector if it is disconnected, or loose.
2. Check the harness for the target part. Replace the harness if it is disconnected, or damaged.
3. Check if the motor runs, sensors turn OFF/ON, has no overloads, and is properly driven. Replace the parts if there are any defects.
4. Check if there are any signs of a short circuit. Replace the parts if there are any defects.
Type
C
Error Name/Error Condition/Major Cause/Solution
Booklet Finisher SR3220 (D3B9) Error
Access error to NVRAM
Error occurs when accessing NV memory.
Connection failure or malfunction of NV memory
Check if the SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps.
1. Pull out and reinsert the NV memory to check if the NV memory is correctly inserted into the IC socket. If the SC cannot be recovered, replace the main board.
Service Call 700-792
SC No.
SC723
SC723-03
SC723-10
Type
B
B
Error Name/Error Condition/Major Cause/Solution
Internal Finisher SR3180 (D766) Error
Power Supply Error
When original source 24V power supply is ON, protection device intercept of non-interlock power supply system is detected.
A motor failure or harness short-circuit occur in the non-interlock power supply system.
• Replace the short-circuited harnesses
• Replace the protection devices
Transport Motor Error
The DCM driver error detection is started after reset, and the error signal is detected for 0.2 sec.
This SC will be issued when the above phenomenon repeated 2 times.
• Transport Motor failure
• Harness short-circuit
• Circuit board failure
• Over current
• Abnormal temperature
• Replace the motor
• Replace the harness
• Replace the circuit board.
903
904
6. Troubleshooting
SC No.
SC723-20
SC723-24
Type
B
B
Error Name/Error Condition/Major Cause/Solution
Junction Gate Motor Error
When the junction gate HP sensor was not turned off for 0.1 sec. applied to the junction gate motor with the HP sensor turned on.
When the junction gate HP sensor was not turned on for 0.6 sec. applied to the junction gate motor with the HP sensor turned off.
This SC will be issued when the above phenomenon repeated 2 times.
• Junction Gate Motor failure
• Connector disconnected
• Over load
• Junction gate HP sensor error
• Check the connection
• Replace the motor/sensor
• Replace the harness
Exit Paper Pressure Motor Error
When the exit paper pressure HP sensor was not turned off for 0.15 sec.
applied to the exit pressure release motor with the HP sensor turned on.
When paper output pressure HP sensor was not turned on for 0.7 sec.
applied to the exit pressure release motor with the HP sensor turned off.
This SC will be issued when the above phenomenon repeated 2 times.
• Exit Pressure Release Motor failure
• Connector disconnected
• Over load
• Exit pressure release HP sensor error
• Check the connection
• Replace the motor/sensor
• Replace the harness
Service Call 700-792
SC No.
SC723-44
Type
B
Error Name/Error Condition/Major Cause/Solution
Stapler Motor Error
When the stapler drive HP sensor was not turned off for 0.6 sec. applied to the stapler motor with the HP sensor turned on.
When stapler drive HP sensor was not turned on for 9 sec. applied to the stapler motor with the HP sensor turned off.
The STM driver error detection is started after reset, and the signal is detected for 0.2 sec.
This SC will be issued when the above phenomenon repeated 2 times.
• Stapler Motor failure
• Connector disconnected
• Stapler Motor overload
• Stapler HP sensor error
• Harness short-circuit
• Circuit board failure
• Excess current
• Abnormal temperature
• Check the connection
• Replace the motor/sensor
• Replace the harness
• Replace the circuit board
905
906
6. Troubleshooting
SC No.
SC723-71
SC No.
SC724
Type
B
Error Name/Error Condition/Major Cause/Solution
Shift Motor Error
When the shift HP sensor was not turned off for 0.15 sec. applied to the shift motor with the HP sensor turned on.
When shift HP sensor was not turned on for 1.1 sec. applied to the shift motor with the HP sensor turned off.
The STM driver error detection is started after reset, and the error signal is detected for 0.2 sec.
This SC will be issued when the above phenomenon repeated 2 times.
• Shift Motor failure
• Connector disconnected
• Shift Motor overload
• Shift HP sensor error
• Harness short-circuit
• Circuit board failure
• Excess current
• Abnormal temperature
Check if the SC occurs by opening/closing covers, and input/output check. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
• The target parts are the motor and related HP sensor that SC occurred.
1. Check if the connector of the target part is connected securely.
Reconnect the connector if it is disconnected, or loose.
2. Check the harness for the target part. Replace the harness if it is disconnected, or damaged.
3. Check if the motor runs, sensors turn OFF/ON, has no overloads, and is properly driven. Replace the parts if there are any defects.
4. Check if there are any signs of a short circuit. Replace the parts if there are any defects.
Type Error Name/Error Condition/Major Cause/Solution
Internal Finisher SR3130 (D690) Error
Service Call 700-792
SC No.
SC724-24
SC724-25
SC724-27
SC724-28
Type
B
B
B
B
Error Name/Error Condition/Major Cause/Solution
Paper Exit Guide Plate Open/Close Motor Error
• When paper exit guide plate open/close motor is driven for 0.15
sec. after paper exit guide plate HP sensor ON, the HP sensor does not switch OFF (1st time is jam notification, 2nd time is SC notification).
• When paper exit guide plate open/close motor is driven for 0.15
sec. after paper exit guide plate HP sensor OFF, the HP sensor does not switch ON (1st time is jam notification, 2nd time is SC notification).
Punch Motor Error
• When punch motor is driven for 0.05 sec. after punch HP sensor
ON, the HP sensor does not switch OFF (1st time is jam notification,
2nd time is SC notification).
• When punch motor is driven for 0.15 sec after punch HP sensor
OFF, the HP sensor does not switch ON (1st time is jam notification,
2nd time is SC notification).
Punch Displacement Motor Error
• When punch displacement motor is driven for 0.166 sec. when punch displacement HP sensor is ON, the HP sensor does not switch
OFF (1st time is jam notification, 2nd time is SC notification).
• When punch displacement motor is driven for 0.832 sec. when punch displacement HP sensor is OFF, the HP sensor does not switch
ON (1st time is jam notification, 2nd time is SC notification).
Punch Horizontal Registration Detection Motor Error
• When horizontal registration displacement motor is driven for 0.428
sec. when horizontal registration displacement HP sensor is ON, the
HP sensor does not switch OFF (1st time is jam notification, 2nd time is SC notification).
• When horizontal registration displacement motor is driven for 1.81
sec. when horizontal registration displacement HP sensor is OFF, the
HP sensor does not switch ON (1st time is jam notification, 2nd time is SC notification).
907
908
6. Troubleshooting
SC No.
SC724-31
SC724-32
SC724-33
SC724-38
Type
B
B
B
B
Error Name/Error Condition/Major Cause/Solution
Jogger Front Motor Error
• When front jogger motor is driven for 0.114 sec. when front jogger
HP sensor is ON, the HP sensor does not switch OFF (1st time is jam notification, 2nd time is SC notification).
• When front jogger motor is driven for 0.6 sec. when front jogger HP sensor is OFF, the HP sensor does not switch ON (1st time is jam notification, 2nd time is SC notification).
Jogger Rear Motor Error
• When rear jogger motor is driven for 0.114 sec. when rear jogger
HP sensor is ON, the HP sensor does not switch OFF (1st time is jam notification, 2nd time is SC notification).
• When rear jogger motor is driven for 0.6 sec. when rear jogger HP sensor is OFF, the HP sensor does not switch ON (1st time is jam notification, 2nd time is SC notification).
Positioning Roller Motor Error
• During initialization/positioning roller descent, even when the positioning roller motor is driven for 0.357 sec. when the positioning roller HP sensor is ON, the HP sensor does not switch OFF (1st time is jam notification, 2nd time is SC notification).
• During initialization, even when the positioning roller motor is driven for 0.714 sec. when the positioning roller HP sensor is OFF, the HP sensor does not switch ON (1st time is jam notification, 2nd time is
SC notification).
• When the positioning roller is lifted from the press position, even when driven for 0.714 sec., the HP sensor does not switch ON (1st time is jam notification, 2nd time is SC notification).
Paper Press Motor Error
• When the paper press HP sensor is ON and the paper press motor is driven for 0.1 sec., the HP sensor does not switch OFF (1st time is jam notification, 2nd time is SC notification).
• When the paper press HP sensor is OFF and the paper press motor is driven for 0.1 sec., the HP sensor does not switch ON (1st time is jam notification, 2nd time is SC notification).
Service Call 700-792
SC No.
SC724-42
SC724-70
SC724-71
Type
B
B
B
Error Name/Error Condition/Major Cause/Solution
Stapler Displacement Movable Motor Error
• Sifter stapler displacement HP sensor ON, even when the stapler retreat motor is driven for 0.25 sec., the HP sensor does not switch
OFF (1st time is jam notification, 2nd time is SC notification).
• After stapler displacement HP sensor OFF, even when the stapler retreat motor is driven for 4.5 sec. the HP sensor does not switch
ON (1st time is jam notification, 2nd time is SC notification).
Shift Tray Ascent/Descent Motor Error
• During ascent from paper surface sensor ON, even after 2 sec.
elapses, the paper surface sensor does not switch OFF (1st time is jam notification, 2nd time is SC notification).
• During descent from paper surface sensor OFF, the paper surface sensor does not switch ON even after 2 sec. elapses (1st time is jam notification, 2nd time is SC notification).
• During descent to the packing position, the full sensor does not switch ON even if 2 sec. elapses.
Shift Motor Error
The level of shift sensor output does not change when the shift motor is driven for 1.86 sec. after the motor in turned ON.
909
910
6. Troubleshooting
SC No.
SC No.
SC724
SC724-80
Type Error Name/Error Condition/Major Cause/Solution
• Motor defective
• Connector disconnected
• Motor overload
• Home position sensor error
• Paper surface sensor error (*SC724-38, 70 only)
Check if the SC occurs by opening/closing covers, and input/output check. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
• The target parts are the motor and related HP sensor that SC occurred.
1. Check if the connector of the target part is connected securely.
Reconnect the connector if it is disconnected, or loose.
2. Check the harness for the target part. Replace the harness if it is disconnected, or damaged.
3. Check if the motor runs, sensors turn OFF/ON, has no overloads, and is properly driven. Replace the parts if there are any defects.
4. Check if there are any signs of a short circuit. Replace the parts if there are any defects.
Type
B
Error Name/Error Condition/Major Cause/Solution
Internal Finisher SR3130 (D690) Error
Shift Motor Error
• When the shift roller HP sensor is ON, the HP sensor does not switch
OFF even when the shift roller motor is driven for 0.567 sec.
1st time is jam notification, 2nd time is SC notification.
• When the shift roller HP sensor is OFF, the HP sensor does not switch
ON even when the shift roller motor is driven for 1.417 sec.
1st time is jam notification, 2nd time is SC notification.
Service Call 700-792
SC No.
SC724-86
SC No.
SC761
SC761-03
SC761-04
Type
B
Error Name/Error Condition/Major Cause/Solution
Stapler Motor Error
• HP sensor does not switch OFF even when the stapler motor is driven for 0.6 sec. after the stapler HP sensor switches ON (1st time is jam notification, 2nd time is SC notification).
• HP sensor does not switch ON even when the stapler motor is driven for 0.6 sec. after the stapler HP sensor switches OFF (1st time is jam notification, 2nd time is SC notification).
• Motor defective
• Connector disconnected
• Motor overload
• Home position sensor error
• Staple jam (*SC724-86 only)
Check if the SC occurs by opening/closing covers, and input/output check. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
• The target parts are the motor and related HP sensor that SC occurred.
1. Check if the connector of the target part is connected securely.
Reconnect the connector if it is disconnected, or loose.
2. Check the harness for the target part. Replace the harness if it is disconnected, or damaged.
3. Check if the motor runs, sensors turn OFF/ON, has no overloads, and is properly driven. Replace the parts if there are any defects.
4. Check if there are any signs of a short circuit. Replace the parts if there are any defects.
Type
B
B
Error Name/Error Condition/Major Cause/Solution
Bridge Unit BU3070 (D685) or Side Tray Type M3 (D725) Error
Protection Device Intercept Error 5V
Protection Device Intercept Error 24V
911
912
6. Troubleshooting
SC No.
SC No.
SC780-01
Type Error Name/Error Condition/Major Cause/Solution
Fuse blowout occurs due to over current during power injection (output detected for longer than 2 seconds).
• Over current of bridge unit motor
• Over current due to short-circuit in PCB
• Replace the bridge unit or side tray
• Replace the PCB of bridge unit or side tray
Type
D
Error Name/Error Condition/Major Cause/Solution
Bank 1 (Upper optional paper tray) Protection Device Intercept Error
When original source of 5V power supply is ON, protection device intercept of 24V power system is detected.
In 24V power supply system:
• Motor defective
• Solenoid defective
• Harness short- circuit
Remove the jammed paper or slip of paper from the tray, and check if the
SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Check if all connectors in tray 1, 2, and optional upper tray are connected securely. Reconnect the connectors if they are disconnected, or loose.
2. Check the harness in tray 1, 2, and optional upper tray. Replace the harness if it is disconnected, or damaged.
3. Check if the motor runs, has no overloads, and is properly driven.
Replace the parts if there are any defects.
4. Check if there are any signs of a short circuit. Replace the parts if there are any defects.
Service Call 700-792
SC No.
SC781-01
SC No.
SC791-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Bank 2 (Lower optional paper tray) Protection Device Intercept Error
When original source of 5V power supply is ON, protection device intercept of 24V power system is detected.
In 24V power supply system:
• Motor defective
• Solenoid defective
• Harness short- circuit
Remove the jammed paper or slip of paper from the tray, and check if the
SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Check if all connectors in tray 1, 2, and optional upper/lower trays are connected securely. Reconnect the connectors if they are disconnected, or loose.
2. Check the harness in tray 1, 2, and optional upper/lower trays.
Replace the harness if it is disconnected, or damaged.
3. Check if the motor runs, has no overloads, and is properly driven.
Replace the parts if there are any defects.
4. Check if there are any signs of a short circuit. Replace the parts if there are any defects.
Type
D
Error Name/Error Condition/Major Cause/Solution
No bridge unit when finisher is present
When power supply is switched on or paper is fed, finisher set is detected but bridge unit set is not detected.
(during internal finisher connection, not detected)
• Bridge unit not attached
• Bridge unit defective
• Reset the bridge unit
• Turn the main power OFF/ON.
913
914
6. Troubleshooting
SC No.
SC792-00
Type
B
Error Name/Error Condition/Major Cause/Solution
No finisher, bridge unit provided
When power supply is switched on, it is recognized there is no finisher, and a bridge unit is fitted.
• Finisher connector set incorrectly
• In a machine which has a bridge unit connected, a finisher is not fitted
• Finisher defective
Connect finisher or disconnect bridge unit, and turn the main power
OFF/ON.
Service Call 816-899
SC816-13
SC816-14
SC816-15 to 18
SC816-19
SC816-20
SC816-22
SC816-23
, 24
SC816-25
No.
Type Error Name/Error Condition/Major Cause/Solution
SC816-** [0x0000] Energy save I/O subsystem error
SC816-01
SC816-02
SC816-03
SC816-04
SC816-05
, 06
SC816-07
D
D
D
D
D
Subsystem error
Sysarch (LPUX_GET_PORT_INFO) error
Transition to STR was denied.
Interrupt in kernel communication driver
Preparation for transition to STR failed.
SC816-08
SC816-09
SC816-10 to 12
D
D
D
D
Sysarch (LPUX_GET_PORT_INFO) error
Sysarch (LPUX_ENGINE_TIMERCTRL) error
Sysarch (LPUX_RETURN_FACTOR_STR) error
Sysarch (LPUX_GET_PORT_INFO) error
D
D
D open() error
Memory address error open() error
D
D
D
D
D
Double open() error open() error
Parameter error read() error write () error
915
916
6. Troubleshooting
No.
SC816-26 to 28
SC816-29
, 30
SC816-35
SC816-36 to 96, 99
D
D
D
Type
D
Error Name/Error Condition/Major Cause/Solution write() communication retry error read() communication retry error read() error
Subsystem error
Energy save I/O subsystem detected some abnormality.
• Energy save I/O subsystem defective
• Energy save I/O subsystem detected a controller board error (nonresponse).
• Error was detected during preparation for transition to STR.
• SC816-99 occurs as a subsystem error except any error from -06 to
96.
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
1. Update the "System/Copy" firmware and the other system firmware modules to the latest version.
2. Disable the STR shift function by SP5-191-001 (Power Str Set).
3. Replace the controller board.
Service Call 816-899
No.
SC817-00
No.
SC818-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Monitor error: File detection / Digital signature error
• Bootloader cannot read any of diagnostic module, kernel, or root filesystem.
• In a bootloader SD card, the digital signature checking for any of diagnostic module, kernel, or root filesystem is failed.
• Any of the following items does not exist or is broken OS Flash ROM,
Diagnostic module in SD card, Kernel, Root filesystem
• Any of the following items is revised fraudulently: Diagnostic module in SD card, Kernel, Root filesystem
• ROM update for controller system
• Use another booting SD card having a valid digital signature
Type
D
Error Name/Error Condition/Major Cause/Solution
Watchdog timer error
The system program fell into a bus-hold state or an endless loop of the program interruption occurred, causing other process to stop.
• System program defective
• Controller board defective
• Optional board defective
• Turn the main power OFF/ON.
• Replace the controller board.
No.
SC819-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Kernel halt error
[xxxx]: Detailed error code
Due to a control error, a RAM overflow occurred during system processing. One of the following messages was displayed on the operation panel.
917
918
6. Troubleshooting
No.
Type Error Name/Error Condition/Major Cause/Solution
[0x5032] HAIC-P2 error
HAIC-P2 decompression error (An error occurred in the ASIC compression/decompression module.)
• The code data saved in the HDD was broken for an unexpected reason. (HDD device defective)
• The code data saved to memory was broken for an unexpected reason. (Memory device defective)
• ASIC defective
• Data other than code data was unzipped due to a software malfunction.
• Turn the main power OFF/ON.
• Replace the HDD.
• Replace the memory
• Replace the controller board.
• Fix the software
[0x5245] Link up error
Link up transaction between Engine ASIC and Veena was not completed within 100 ms.
Either one of following message appears on console if Link up error occurs.
RESUME:PCI-Express bus ROOT_DL status error
RESUME:PCI-Express bus DETUP status error
"0x53554D45" -> Link up error
Also, error code "0x5245" and detail code ""0x53554D45" -> Link up error" appears on operation panel.
• Turn the main power OFF/ON.
• Replace the controller board or the engine board (IPU, BCU)
Service Call 816-899
No.
Type Error Name/Error Condition/Major Cause/Solution
[0x5355] L2 status time out
L2 status register between Engine ASIC and Veena was not reached the target value within 1 sec.
Engine ASIC during operation was rebooted or shifted to energy saving mode.
Machine reboots when SC23x, SC30x occurs.
If Engine ASIC is working when rebooting (or shifting to the energy saving mode), L2 status value is not on target.
The following message appears on console.
SUSPEND:PCI-Express L2 Status Check Error
SUSPEND:PCI-Express L2 Status Check Error
Also, error code "0x5355" and detail code ""0x5350454E44" -> L2 status time out" appears on operation panel.
• Turn the main power OFF/ON.
• Replace the controller board or the engine board (IPU, BCU)
[0x6261] HDD defective
Received file system data was broken even if the initialization succeeds and there was no error reply from the HDD.
Power supply disconnection during data writing to the HDD.
Replace the HDD.
This SC may occur when turning on the machine for the first time with a new HDD. In this case, turn the main power off/on.
[0x696e] gwinit processing end
If the SCS process is ended for some reason
If an unexpected error occurs at SCS processing end, gwint processing also halts (this result is judged a kernel stop error, by gwinit specification)
"0x69742064" -> "init died"
Turn the main power OFF/ON.
919
920
6. Troubleshooting
No.
Type Error Name/Error Condition/Major Cause/Solution
[0x766d] VM full error
Occurs when too much RAM is used during system processing
"vm_pageout: VM is full"
Turn the main power OFF/ON.
Console string
Other error (characters on operation panel)
System detected internal mismatch error
• Software defective
• Insufficient memory
• Hardware driver defective (RAM, flash memory)
• Replace with a larger capacity RAM, or flash memory.
• Replace the controller board.
• Replace the connected controller option with a new one.
No.
SC820-00
Type
C
Error Name/Error Condition/Major Cause/Solution
Self-diagnostics error: CPU
[XXXX]: Detailed error code
[0612] ASIC interrupt error
Interrupt occurs in an ASIC.
• ASIC device error
• Peripherals device error
• Replace the controller board
• Replace the connected controller option with a new one.
Service Call 816-899
No.
SC821-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Self-diagnostics error: ASIC
[xxxx]: Detailed error code
[0B00] ASIC register check error
The write-&-verify check has occurred in the ASIC.
Defective ASIC device
Replace the controller board.
[0B06] ASIC detection error
Error in the I/O ASIC for system control detection
• Defective ASIC
• Defective North Bridge and PCII/F
Replace the controller board.
921
922
6. Troubleshooting
No.
Type Error Name/Error Condition/Major Cause/Solution
[0D05] Comparison error of CPU and ASIC timer
The CPU checks if the ASIC timer works correctly compared with the CPU timer. If the ASIC timer does not function in the specified range, this SC code is displayed.
• Defective ASIC timer device
• Defective CPU device
Replace the controller board.
[50A1] Video bridge device detection error
Video bridge device is not detected.
• Video bridge device ASIC (HARP or KLAVIER) defective.
• Connection error between PCI I / F of the controller ASIC and video bridge device ASIC.
Replace the controller board
[50A2] Video bridge device (ASIC) register error
The CPU detects the video bridge device, but detects error data from the video bridge device.
Defective I/F between the video bridge device and the controller
Replace the controller board.
Service Call 816-899
No.
SC822-00
Type
D
Details (Symptom, Possible Cause, Troubleshooting Procedures)
Self-diagnostic error: HDD
[xxxx]: Detailed error code
[3003] HDD timeout
Check performed only when HDD is installed:
• HDD device busy for over 31sec.
• After a diagnostic command is set for the HDD, but the device remains busy for over 6sec.
• HDD defective
• HDD harness disconnected, defective
• Controller board defective
• Replace the HDD.
• Replace the HDD connector.
• Replace the controller board.
[3004] Diagnostic command error
No response to the self-diagnostic command from the ASIC to the HDD.
HDD defective
Replace the HDD.
923
924
6. Troubleshooting
No.
Type Details (Symptom, Possible Cause, Troubleshooting Procedures)
[3013] HDD timeout (first machine)
HDD device busy for over 31 seconds.
A diagnostic command is set for the HDD, but the device remains busy for over 6 seconds.
• Defective HDD device
• Defective HDD connector
• Defective ASIC device
• Replace or remove the HDD device.
• Replace the HDD connector
• Replace the controller board
[3014] Diagnostics command error (First machine)
Result of the issuance of diagnostic command is error.
Defective HDD device
Replace the HDD device.
Service Call 816-899
No.
SC823-00
Type
B
Error Name/Error Condition/Major Cause/Solution
Self-diagnostics error: NIC
[XXXX]: Detailed error code
[6101] MAC address check sum error
The result of the MAC address check sum does not match the check sum stored in ROM.
• Defective SEEP ROM
• Defective I2C bus (connection)
Replace the controller board.
[6104] PHY IC error
The PHY IC on the controller cannot be correctly recognized.
• Defective PHY chip
• Defective ASIC MII I/F
Replace the controller board.
[6105] PHY IC loop-back error
An error occurred during the loop-back test for the PHY IC on the controller.
• PHY chip
• Defective MAC of ASIC (SIMAC/COMIC/CELLO)
• Defective I/F with the PHY board
• Defective solder on the PHY board
Replace the controller board.
925
926
6. Troubleshooting
No.
SC824-00
Type
C
Error Name/Error Condition/Major Cause/Solution
Self-diagnostics error: NVRAM (resident)
[XXXX]: Detailed error code
[1401] NVRAM verify error
NVRAM device is missing or NVRAM device is damaged.
• The NVRAM device is missing.
• The NVRAM device is damaged.
• NVRAM backup battery exhausted
• NVRAM socket damaged
Replace the NVRAM device.
No.
SC833-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Self-diagnostic error: Engine I/F ASIC
[XXXX]: Detailed error code
[0F30] Engine I/F ASIC detection error
ASIC (Mandolin) for engine control could not be detected.
ASIC (Mandolin) error
Replace the Engine I/F board (mother board).
[50B1] Video device: clock generator detection error
Could not initialize or read the bus connection.
• Defective connection bus
• Defective SSCG
Replace the Engine I/F board (mother board).
[50B2] Video device: clock generator verify error
Value of the SSCG register is incorrect.
• Defective connection bus
• Defective SSCG
Replace the Engine I/F board (mother board).
Service Call 816-899
No.
SC834-00
Type Error Name/Error Condition/Major Cause/Solution
D Self-diagnostic error: Optional memory
[5101] Engine I/F optional memory verify error
An error occurs after write/verify check for optional RAM on the engine
I/F board (mother board).
Defective memory device
Replace the Engine I/F board (mother board).
927
928
6. Troubleshooting
No.
SC835-00
Type
B
Error Name/Error Condition/Major Cause/Solution
Self-diagnostic error: Centronic device
[xxxx]: Detailed error code
[1102] Verify error
The loopback connector is connected but check results is an error.
• IEEE1284 connector error
• Centronic loopback connector defective
Replace the controller board.
[110C] DMA verify error
The loopback connector is connected but check results is an error.
• ASIC device error
• IEEE1284 connector error
• Centronic loopback connector is defective
Replace the controller board.
[1120] Loopback connector not detected
Centronic loopback connector is not connected for detailed selfdiagnostic test.
• Centronic loopback connector not connected correctly
• Centronic loopback connector is defective
• ASIC device is defective
• Connect the centronic loopback connector
• Replace the centronic loopback connector
• Replace the controller board.
Service Call 816-899
No.
SC838-00
Type
C
Error Name/Error Condition/Major Cause/Solution
Self-diagnostic Error: Clock Generator
[xxxx]: Detailed error code
[2701] Verify error
A verify error occurred when setting data was read from the clock generator via the I2C bus.
• Defective clock generator
• Defective I2C bus
• Defective I2C port on the CPU
Replace the controller board.
No.
SC839-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Self-diagnostic Error: Serial Flash
[xxxx]: Detailed error code
[9001] Serial Flash access error
USB NAND Flash ROM cannot be read.
Defective controller board
Replace the controller board.
No.
SC840-00
Type
D
-
Error Name/Error Condition/Major Cause/Solution
EEPROM access error
• During the I/O processing, a reading error occurred. The 3rd reading failure causes this SC code.
• During the I/O processing, a writing error occurred.
• Defective EEPROM
929
930
6. Troubleshooting
No.
SC841-00
Type
D
-
Error Name/Error Condition/Major Cause/Solution
EEPROM read data error
Mirrored data of the EEPROM is different from the original data in
EEPROM.
Data in the EEPROM is overwritten for some reason.
No.
SC842-00
Type
C
Error Name/Error Condition/Major Cause/Solution
Nand-Flash updating verification error
SCS write error (verify error) occurred at the Nand-Flash module when remote ROM or main ROM was updated.
Nand-Flash defective
Turn the main power OFF/ON.
No.
SC842-01
Type
C
Error Name/Error Condition/Major Cause/Solution
Insufficient Nand-Flash blocks (threshold exceeded)
At startup, or when machine returned from low power mode, the Nand-
Flash status was read and judged that the number of unusable blocks had exceeded threshold, and then SCS generated the SC code.
Number of unusable blocks exceeded threshold for Nand-Flash
Replace the controller board.
No.
SC842-02
Type
C
Error Name/Error Condition/Major Cause/Solution
Number of Nand-Flash block deletions exceeded
At startup, or when the machined returned from low power mode, the
Nand-Flash was read and judged that the number of deleted blocks had exceeded threshold, and then SCS generated this SC code.
Number of blocks deleted exceeded threshold for Nand-Flash
Replace the controller board.
Service Call 816-899
No.
SC845
SC845-01
SC845-02
SC845-03
SC845-04
SC845-05
D
D
D
D
D
Type Error Name/Error Condition/Major Cause/Solution
Hardware Error Detected when the automatic firmware update
Engine Board
Controller Board
Operation Panel (Normal)
Operation Panel (Smart Panel)
FCU
When updating the firmware automatically (ARFU), the firmware cannot be read or written normally, and the firmware update cannot be completed even by 3 retries.
Hardware abnormality of the target board
Replacing the target board
For SC845-02, HDD and memory may cause the problem. Replace the
HDD or memory if the SC cannot be recovered by replacing the controller board.
No.
SC853-00
Type
B
Error Name/Error Condition/Major Cause/Solution
Bluetooth device connection error
The Bluetooth hardware (USB type) was connected after the machine was turned on.
The Bluetooth hardware (USB type) was connected after the machine was turned on.
Always connect the Bluetooth device (USB type) before the machine is turned on.
931
932
6. Troubleshooting
No.
SC854-00
Type
B
Error Name/Error Condition/Major Cause/Solution
Bluetooth device disconnected
The Bluetooth hardware (USB type) was disconnected after the machine was turned on.
The Bluetooth hardware (USB type) was disconnected after the machine was turned on.
Never remove Bluetooth (USB type) after machine starts
No.
SC855-01
No.
SC855-02
Type
B
Error Name/Error Condition/Major Cause/Solution
Wireless LAN board error (driver attachment failure)
Wireless LAN board error (wireless LAN card: 802.11 is covered)
• Defective wireless LAN board
• Loose connection
• Turn the main power OFF/ON.
• Replace wireless LAN board
Type
B
Error Name/Error Condition/Major Cause/Solution
Wireless LAN board error (driver initialization failure)
Wireless LAN board error (wireless LAN card: 802.11 is covered)
• Defective wireless LAN board
• Loose connection
• Turn the main power OFF/ON.
• Replace wireless LAN board
Service Call 816-899
No.
SC857-00
Type
B
Error Name/Error Condition/Major Cause/Solution
USB I/F Error
The USB interface is unusable because of a driver error.
USB driver error (There are three causes of USB error: RX error/CRC error/STALL. SC is issued only in the case of STALL.)
• Check USB connection.
• Replace the controller board.
No.
SC858-00
No.
SC858-01
Type
A
Type
A
Error Name/Error Condition/Major Cause/Solution
Data encryption conversion error (Key Setting Error)
A serious error occurred during an attempt to update the encryption key.
• USB Flash, other data, corrupted
• Communication error caused by electrostatic noise
• Controller board defective
Replace the controller board.
Error Name/Error Condition/Major Cause/Solution
Data encryption conversion error (HDD Key Setting Error)
A serious error occurred during an attempt to update the encryption key.
• USB Flash, other data, corrupted
• Communication error caused by electrostatic noise
• Controller board defective
• Turn the main power OFF/ON.
• If the error persists, replace the controller board.
933
934
6. Troubleshooting
No.
SC858-02
Type
A
Error Name/Error Condition/Major Cause/Solution
Data encryption conversion error (NVRAM Read/Write Error)
A serious error occurred after data conversion during an attempt to update the encryption key.
NVRAM defective
• Replace the NVRAM.
• Replace the controller board.
No.
SC858-30
No.
SC858-31
Type
A
Error Name/Error Condition/Major Cause/Solution
Data encryption conversion error (NVRAM Before Replace Error)
A serious error occurred after data conversion during an attempt to update the encryption key.
Software error such as conversion parameters being invalid.
• Turn the main power OFF/ON.
• If the error persists, replace the controller board.
Type
A
Error Name/Error Condition/Major Cause/Solution
Data encryption conversion error (Other Error)
A serious error occurred after data conversion during an attempt to update the encryption key.
Controller board defective
Replace the controller board.
Service Call 816-899
No.
SC859-00
Type
B
Error Name/Error Condition/Major Cause/Solution
Data encryption conversion HDD conversion error
When the data encryption key was updated, HDD data was converted, but not correctly. Image displayed at conversion only (this SC is not displayed), but SC is displayed after machine is cycled off/on.
• HDD conversion was set with the data encryption key update function, but the HDD was removed.
• Machine lost power during data encryption key update
• Electrostatic noise, or an HDD error occurred, during data encryption key update, and data was not encrypted.
• Check HDD connection.
• Format the HDD (SP5-832: HDD formatting).
• If there is a problem with the HDD, it has to be replaced.
No.
SC859-01
Type
B
Error Name/Error Condition/Major Cause/Solution
Data encryption conversion HDD conversion error (HDD check error)
When the data encryption key was updated, HDD data was converted, but not correctly. Image displayed at conversion only (this SC is not displayed), but SC is displayed after machine is cycled off/on.
• HDD conversion was set with the data encryption key update function, but the HDD was removed.
• Machine lost power during data encryption key update
• Electrostatic noise, or an HDD error occurred, during data encryption key update, and data was not encrypted.
• Check HDD connection.
• Format the HDD (SP5-832: HDD formatting).
• If there is a problem with the HDD, it has to be replaced.
935
936
6. Troubleshooting
No.
SC859-02
Type
B
Error Name/Error Condition/Major Cause/Solution
Data encryption conversion HDD conversion error (Power failure during conversion)
When the data encryption key was updated, HDD data was converted, but not correctly. Image displayed at conversion only (this SC is not displayed), but SC is displayed after machine is cycled off/on.
Details:
NVRAM/HDD conversion is incomplete.
Power failure occurred during encryption key update.
None
The display after restart instructs the user to format the HDD.
No.
SC859-10
Type
B
Error Name/Error Condition/Major Cause/Solution
Data encryption conversion HDD conversion error (Data read/write command error)
When the data encryption key was updated, HDD data was converted, but not correctly. Image displayed at conversion only (this SC is not displayed), but SC is displayed after machine is cycled off/on.
Details:
Abnormal DMAC return value has been received two or more times
(DMAC timeout, serial communication error etc.)
HDD was not successfully converted during encryption key update due to
HDD errors or cable noises.
• Check HDD connection.
• Format the HDD (SP5-832: HDD formatting).
• If there is a problem with the HDD, it has to be replaced.
Service Call 816-899
SC860
RTB 26
No.
SC860-00
Type
B
Error Name/Error Condition/Major Cause/Solution
HDD startup error at main power on (HDD error)
• The HDD is connected but the driver detected the following errors.
• SS_NO.T_READY:/* (-2)HDD does not become READY*/
• SS_BAD_LABEL:/* (-4)Wrong partition type*/
• SS_READ_ERROR:/* (-5)Error occurred while reading or checking the label*/
• SS_WRITE_ERROR:/* (-6)Error occurred while writing or checking the label*/
• SS_FS_ERROR:/* (-7)Failed to repair the filesystem*/
• SS_MOUNT_ERROR:/* (-8)Failed to mount the filesystem*/
• SS_COMMAND_ERROR:/* (-9)Drive not responding to command*/
• SS_KERNEL_ERROR:/* (-10)Internal kernel error*/
• SS_SIZE_ERROR:/* (-11)Drive size too small*/
• SS_NO._PARTITION:/* (-12)The specified partition does not exist*/
• SS_NO._FILE:/* (-13)Device file does not exist*/
• Attempted to acquire HDD status through the driver but there has been no response for 30 seconds or more.
• Unformatted HDD
• Label data corrupted
• HDD defective
Format the HDD (SP5-832: HDD formatting) through SP mode.
937
938
6. Troubleshooting
No.
SC862-00
No.
SC863-01
Type
D
Error Name/Error Condition/Major Cause/Solution
Number of the defective sector reaches the maximum count
101 defective sectors are generated at the image storage area in the
HDD.
SC863 occurs during the HDD reading and defective sectors are registered up to 101.
• Format the HDD with SPSP5-832.
• Replace the HDD.
Type
D
Error Name/Error Condition/Major Cause/Solution
HDD data read failure
The data written to the HDD cannot be read normally.
Bad sectors were generated during operation.
(An error occurred in an area that does not belong to a partition, such as the disk label area.)
Guide for when to replace the HDD
1. When SC863 has occurred ten times or more
• The interval is short.
• Repeatedly occurs in the same situation (At power-on, etc.).
• Startup takes a long time when the main power is turned on.
2. It takes a long time after main power on for the operation panel to become ready.
HDD access may be consuming time. Normal HDD access time after main power on is about 5 seconds. If the machine is not waiting for the engine to be ready and it still takes 20 to 30 seconds or more, the HDD may be the cause. If there is a problem with the HDD, HDDrelated SCs such as SC860 and SC863 will occur frequently. Print the SC log data and check them.
Service Call 816-899
No.
SC863-02 to 23
Type
D
Error Name/Error Condition/Major Cause/Solution
HDD data read failure
The data written to the HDD cannot be read normally.
Bad sectors were generated during operation.
(An error occurred in partition "a" (SC863-02) to partition "v"
(SC863-23)).
Guide for when to replace the HDD
1. When SC863 has occurred ten times or more
• The interval is short.
• Repeatedly occurs in the same situation (At power-on, etc.).
• Startup takes a long time when the main power is turned on.
2. It takes a long time after main power on for the operation panel to become ready.
HDD access may be consuming time. Normal HDD access time after main power on is about 5 seconds. If the machine is not waiting for the engine to be ready and it still takes 20 to 30 seconds or more, the HDD may be the cause. If there is a problem with the HDD, HDDrelated SCs such as SC860 and SC863 will occur frequently. Print the SC log data and check them.
No.
SC864-00
Type
D
Error Name/Error Condition/Major Cause/Solution
HD data CRC error
During HD operation, the HD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HD.
-
HD defective
939
940
6. Troubleshooting
No.
SC864-01
Type
D
Error Name/Error Condition/Major Cause/Solution
HDD data CRC error
During HDD operation, the HDD cannot respond to a CRC error query.
Data transfer did not execute normally while data was being written to the
HDD.
Bad sectors were generated during operation.
(An error occurred in an area that does not belong to a partition, such as the disk label area.)
• Format the HDD.
• Replace the HDD.
No.
SC864-02 to 23
Type
D
Error Name/Error Condition/Major Cause/Solution
HDD data CRC error
During HDD operation, the HDD cannot respond to a CRC error query.
Data transfer did not execute normally while data was being written to the
HDD.
Bad sectors were generated during operation.
(An error occurred in partition "a" (SC864-02) to partition "v"
(SC864-23)).
• Format the HDD.
• Replace the HDD.
No.
SC865-00
Type
D
Error Name/Error Condition/Major Cause/Solution
HD access error
During HDD operation, the HDD returned an error.
The HDD returned an error that does not constitute SC863 (bad sector) or
SC864 (CRC error).
Replace the HDD.
Service Call 816-899
No.
SC865-01
No.
SC865-02 to 23
Type
D
Type
D
Error Name/Error Condition/Major Cause/Solution
HDD access error
During HDD operation, the HDD returned an error.
The HDD returned an error that does not constitute SC863 (bad sector) or
SC864 (CRC error).
(An error occurred in an area that does not belong to a partition, such as the disk label area.)
Replace the HDD.
Error Name/Error Condition/Major Cause/Solution
HDD access error
During HDD operation, the HDD returned an error.
The HDD returned an error that does not constitute SC863 (bad sector) or
SC864 (CRC error).
(An error occurred in partition "a" (SC865-02) to partition "v"
(SC865-23)).
Replace the HDD.
No.
SC865-50 to 73
Type
D
Error Name/Error Condition/Major Cause/Solution
HDD time-out error
The machine does not detect a reply from the HDD during the HDD operation.
The HDD does not respond to the read/ write command from the machine.
• Check the harness connections between the controller board and
HDD.
• Replace the HDD.
941
942
6. Troubleshooting
No.
SC866-00
Type
B
Error Name/Error Condition/Major Cause/Solution
SD card authentication error
A license error of an application that is started from the SD card was detected.
Invalid program data is stored on the SD card.
Store a valid program data on the SD card.
No.
SC867-00
Type
C
Error Name/Error Condition/Major Cause/Solution
SD card removed
The SD card was removed while the machine is on.
An application SD card has been removed from the slot (mount point of /mnt/sd0).
Turn the main power OFF/ON.
No.
SC867-01
Type
C
Error Name/Error Condition/Major Cause/Solution
SD card removed
The SD card was removed while the machine is on.
An application SD card has been removed from the slot (mount point of /mnt/sd1).
Turn the main power OFF/ON.
No.
SC867-02
Type
C
Error Name/Error Condition/Major Cause/Solution
SD card removed
The SD card was removed while the machine is on.
An application SD card has been removed from the slot (mount point of /mnt/sd2).
Turn the main power OFF/ON.
Service Call 816-899
No.
SC868-**
SC868-00
SC868-01
SC868-02
Type
D
D
D
Error Name/Error Condition/Major Cause/Solution
SD card access error
The SD controller returned an error during operation.
(An error occurred at the mount point of /mnt/sd0)
The SD controller returned an error during operation.
(An error occurred at the mount point of /mnt/sd1)
The SD controller returned an error during operation.
(An error occurred at the mount point of /mnt/sd2)
943
944
6. Troubleshooting
No.
Type Error Name/Error Condition/Major Cause/Solution
• SD card defective
• SD controller defective
Slot number is displayed on the sub code.
Detail code is described in SMC print can confirm the details of the error.
• -13 to -3: File system check error
• Otherwise (no code, -2) : Device access error
SD card that starts an application
1.
Turn the main power off and check the SD card insertion status.
2.
If no problem is found, insert the SD card and turn the main power on.
3.
If an error occurs, replace the SD card.
4.
If the error persists even after replacing the SD card, replace the controller board.
SD card for users
1.
In case of a file system error, reformat the SD card (using the "SD Formatter" made by Panasonic).*
In case of a device access error
1.
Turn the main power off and check the SD card insertion status.
2.
If no problem is found, insert the SD card and turn the main power on.
3.
If an error occurs, use another SD card.
4.
If the error persists even after replacing the SD card, replace the controller board.
* Do not format an SD card supplied with the main machine or sold as an option. You may only format SD cards used for firmware update by a customer engineer.
No.
SC869-**
Type Error Name/Error Condition/Major Cause/Solution
Malfunction of the proximity sensor (human detection sensor) is detected
Service Call 816-899
No.
SC869-01
SC869-02
Type
C
C
Error Name/Error Condition/Major Cause/Solution
Continuously detecting malfunction
The proximity sensor (human detection sensor) keeps in a detection state and accumulated time exceeds 24 hours.
The proximity sensor (human detection sensor) is disabled and is in the detection state at all times.
Continuously non-detecting malfunction
In the non-detection state, the following operations are detected 20 times continuously.
• Pressing "energy saver" key or touching the operation panel
• Opening/closing the plate cover or ADF
• Setting the original
• Opening the front cover
• Opening the paper feed tray
The proximity sensor (human detection sensor) is disabled and is in the non-detection state at all times.
945
946
6. Troubleshooting
No.
No.
SC870-00
SC870-01
SC870-02
SC870-03
SC870-04
SC870-05
Type
Type
B
B
B
B
B
B
Error Name/Error Condition/Major Cause/Solution
1. Go to the SP5-102-203 (AutoDetect: HumanDetectSetting).
2. Cover the sensor with 10 sheets of plain paper, and then execute the
SP. Make sure that it becomes "0". (Do not place your hand near the sensor, even over the paper, when covering the sensor)
3. Remove the paper from the sensor and make sure that it becomes
"1".
4. If the sensor reacts normally in step 2 and 3, check if there are any other possible factors around the machine that may cause the temperature change such as a heater or a fan. (Deal with the issue as necessary)
5. Replace the proximity sensors (human detection sensors) and proximity sensor (human detection sensor) board if an abnormal value is detected during steps 2 and 3.
6. Turn on the main power on and perform steps 1, 2, and 3 again.
7. If the SC is not solved, turn the main power off and replace the harness which connects the proximity sensors (human detection sensors) and the proximity sensor (human detection sensor) board.
8. If the SC is still not solved, there is a possibility that other parts of the machine such as the connector at the controller side or the harness between proximity sensor (human detection sensor) board and IPU are broken.
Error Name/Error Condition/Major Cause/Solution
Address Book data error (Anytime: Address Book Error.)
Address Book data error (On startup: Media required for storing the
Address Book is missing.)
Address Book data error (On startup: encryption is configured but the module required for encryption (DESS) is missing.)
Address Book data error (Initialization: Failed to generate a file to store internal Address Book.)
Address Book data error (Initialization: Failed to generate a file to store delivery sender.)
Address Book data error (Initialization: Failed to generate a file to store delivery destination.)
Service Call 816-899
No.
SC870-06
SC870-07
SC870-08
SC870-09
SC870-10
SC870-11
SC870-20
SC870-21
SC870-22
SC870-23
SC870-24
SC870-25
SC870-26
SC870-27
SC870-30
SC870-31
SC870-32
SC870-41
B
B
B
B
B
B
B
B
B
Type
B
B
B
B
B
B
B
B
B
Error Name/Error Condition/Major Cause/Solution
Address Book data error (Initialization: Failed to generate a file to store information required for LDAP search.)
Address Book data error (Initialization: Failed to initialize entries required for machine operation.)
Address Book data error (Machine configuration: HDD is present but the space for storing the Address Book is unusable.)
Address Book data error (Machine configuration: Inconsistency in the
NVRAM area used for storing settings required for Address Book configuration.)
Address Book data error (Machine configuration: Cannot make a directory for storing the Address Book in the SD/USB FlashROM.)
Address Book data error (On startup: Inconsistency in Address Book entry number.)
Address Book data error (File I/O: Failed to initialize file.)
Address Book data error (File I/O: Failed to generate file.)
Address Book data error (File I/O: Failed to open file.)
Address Book data error (File I/O: Failed to write to file.)
Address Book data error (File I/O: Failed to read file.)
Address Book data error (File I/O: Failed to check file size.)
Address Book data error (File I/O: Failed to delete data.)
Address Book data error (File I/O: Failed to add data.)
Address Book data error (Search: Failed to obtain data from cache when searching in the machine Address Book. delivery destination/sender.)
Address Book data error (Search: Failed to obtain data from cache during
LDAP search.)
Address Book data error (Search: Failed to obtain data from cache while searching the WS-Scanner Address Book.)
Address Book data error (Cache: failed to obtain data from cache.)
947
948
6. Troubleshooting
No.
SC870-50
SC870-51
SC870-52
SC870-53
SC870-54
SC870-55
SC870-56
SC870-57
SC870-58
SC870-59
SC870-60
Type
B
B
B
B
B
B
B
B
B
B
B
Error Name/Error Condition/Major Cause/Solution
Address Book data error (On startup: Detected abnormality of the Address
Book encryption status.)
Address Book data error (Encryption settings: Failed to create directory required for conversion between plaintext and encrypted text.)
Address Book data error (Encryption settings: Failed to convert from plaintext to encrypted text.)
Address Book data error (Encryption settings: Failed to convert from encrypted text to plaintext.)
Address Book data error (Encryption settings: Detected data inconsistency when reading the encrypted Address Book.)
Address Book data error (Encryption settings: Failed to delete file when changing encryption setting.)
Address Book data error (Encryption settings: Failed to erase the file that records the encryption key during an attempt to change the encryption setting.)
Address Book data error (Encryption settings: Failed to move a file during an attempt to change the encryption setting.)
Address Book data error (Encryption settings: Failed to delete a directory during an attempt to change the encryption setting.)
Address Book data error (Encryption settings: Detected a resource shortage during an attempt to change the encryption setting.)
Address Book data error (Unable to obtain the on/off setting for administrator authentication (06A and later).)
Service Call 816-899
No.
Type Error Name/Error Condition/Major Cause/Solution
When an error related to the Address Book is detected during startup or operation.
• Software bug
• Inconsistency of Address Book source location (machine/delivery server/LDAP server)
• Inconsistency of Address Book encryption setting or encryption key
(NVRAM or HDD was replaced individually without formatting the
Address Book)
• Address Book storage device (SD/HDD) was temporarily removed or hardware configuration does not match the application configuration.
• Address Book data corruption was detected.
Install the device that contains address book information properly, and turn the main power off/on. If SC occurs again, do the following steps.
1. After installing the HDD, or SD/USB ROM, execute SP5-846-046
(UCS Setting).
2. Wait more than 3 seconds, then execute SP5-832 (HDD Formatting).
3. Turn the main power OFF/ON.
Procedure after SC870 is cleared
1. If there is backup data in SD card or Web Image Monitor, restore the address book data. (To restore from SD card, enter the encryption password which is the same as when you enter to backup.)
No.
SC871-00
Type
D
Error Name/Error Condition/Major Cause/Solution
FCU error
An error occurred when FCS detects FCU defective.
• Time-out error
• Abnormal Parameter
• Turn the main power OFF/ON.
• Update the firmware if more recent firmware was released.
949
950
6. Troubleshooting
No.
SC872-00
No.
SC873-00
Type
B
Error Name/Error Condition/Major Cause/Solution
HDD mail reception error
An error was detected on the HDD immediately after the machine was turned on.
• HDD defective
• Power was turned off while the machine used the HDD.
• Format the HDD (SP5-832-007: HDD Formatting: Mail RX Data).).
• Replace the HDD.
When you do the above, the following information will be initialized.
• Partly received partial mail messages.
• Already-read statuses of POP3-received messages (All messages on the mail server are handled as new messages).
Type
B
Error Name/Error Condition/Major Cause/Solution
HDD mail reception error
An error was detected on the HDD immediately after the machine was turned on.
• HDD defective
• Power was turned off while the machine used the HDD.
• Format the HDD (SP5-832-007 : HDD Formatting: Mail RX Data).
• Replace the HDD.
When you do the above, the following information will be initialized.
• Sender’s mail text
• Default sender name/password (SMB/FTP/NCP)
• Administrator mail address
• Scanner delivery history
No.
SC874-05
SC874-06
Type
D
D
Error Name/Error Condition/Major Cause/Solution
Delete all error (Delete data area) : Read error
Delete all error (Delete data area) : Write error
Service Call 816-899
SC874-16
SC874-41
SC874-42
SC874-61 to -65
SC874-66
SC874-67
SC874-68
SC874-69
SC874-70
SC874-99
No.
SC874-09
SC874-10
SC874-12
SC874-13
SC874-14
SC874-15
D
D
D
D
Type
D
D
D
D
D
D
D
D
D
D
D
D
Error Name/Error Condition/Major Cause/Solution
Delete all error (Delete data area) : No response from HDD
Delete all error (Delete data area) : Error in Kernel
Delete all error (Delete data area) : No designated partition
Delete all error (Delete data area) : No device file
Delete all error (Delete data area) : Start option error
Delete all error (Delete data area) : No designated sector number
Delete all error (Delete data area) : failure in performing hdderase
Delete all error (Delete data area) : Other fatal errors
Delete all error (Delete data area) : End by cancellation
Delete all error (Delete data area) : library error
Delete all error (Delete data area) : Unavailable
Delete all error (Delete data area) : Erasing not finished
Delete all error (Delete data area) : HDD format failure (Normal)
Delete all error (Delete data area) : HDD format failure (Abnormal)
Delete all error (Delete data area) : Unauthorized library
Delete all error (Delete data area) : other errors
An error occurred while data was being erased on HDD or NVRAM.
• Error detected in HDD data delete program
• Error detected in NVRAM data delete program
• The "Delete All" option was not set
• Turn the main power switch off and back on, and then execute "Erase
All Memory" under UP mode again. (However, if there is a defective sector or other problem with the hard disk, the error will persist even after trying the above.)
• If the "Delete All" option is not installed when this error occurs, install the option.
951
952
6. Troubleshooting
No.
SC875-01
SC875-02
Type
D
D
Error Name/Error Condition/Major Cause/Solution
Delete all error (HDD erasure) (hddchack –i error)
Delete all error (HDD erasure) (Data deletion failure)
An error was detected before HDD/data erasure starts. (Failed to erase data/failed to logically format HDD)
• HDD logical formatting failed.
• The modules failed to erase data.
Turn the main power OFF/ON.
No.
SC876-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Log Data Error
An error was detected in the handling of the log data at power on or during machine operation.
• Damaged log data file.
• Log encryption is enabled but encryption module is not installed.
• Inconsistency of encryption key between NV-RAM and HDD.
• Software bug.
Try the SC876-01 to -99 solutions listed below. If it is not solved, do the following steps (for when only an HDD is replaced):
1. Disconnect the HDD and turn ON the main power.
2. Execute SP5-801-019 (Memory Clear: LCS Memory Clr) to Initialize the LCS settings.
3. Turn OFF the main power.
4. Connect the HDD and turn ON the main power.
5. Execute SP5-832-004 (HDD Formatting (Job Log)).
6. Turn OFF the main power.
* The following step is to configure the logging/encryption setting again.
7. Turn ON the main power.
Service Call 816-899
No.
SC876-01
Type
D
Error Name/Error Condition/Major Cause/Solution
Log Data Error 1
An error was detected in the handling of the log data at power on or during machine operation.
Damaged log data file
Initialize the HDD (SP5-832-004).
No.
SC876-02
Type
D
Error Name/Error Condition/Major Cause/Solution
Log Data Error 2
An error was detected in the handling of the log data at power on or during machine operation.
Log encryption is enabled but encryption module is not installed.
• Replace or set again the encryption module.
• Disable the log encryption setting.
No.
SC876-03
Type
D
Error Name/Error Condition/Major Cause/Solution
Log Data Error 3
An error was detected in the handling of the log data at power on or during machine operation.
Inconsistency of encryption key between NV-RAM and HDD.
• Disable the log encryption setting.
• Initialize LCS memory (SP5801-019).
• Initialize the HDD (SP5-832-004).
953
954
6. Troubleshooting
No.
SC876-04
Type
D
Error Name/Error Condition/Major Cause/Solution
Log Data Error 4
An error was detected in the handling of the log data at power on or during machine operation.
• Log encryption key is disabled but the log data file is encrypted.
(NVRAM data corruption)
• Log encryption key is enabled but the log data file is not encrypted.
(NVRAM data corruption)
Initialize the HDD (SP5-832-004).
No.
SC876-05
Type
D
Error Name/Error Condition/Major Cause/Solution
Log Data Error 5
An error was detected in the handling of the log data at power on or during machine operation.
• Only the NV-RAM has been replaced with one previously used in another machine.
• Only the HDD has been replaced with one previously used in another machine.
• Attach the original NV-RAM.
• Attach the original HDD.
• With the configuration that caused the SC, initialize the HDD
(SP5-832-004).
No.
SC876-99
Type
D
Error Name/Error Condition/Major Cause/Solution
Log Data Error 99
An error was detected in the handling of the log data at power on or during machine operation.
-
Other causes
Service Call 816-899
No.
SC877-00
Type
B
Error Name/Error Condition/Major Cause/Solution
Data Overwrite Security card error
The "Auto Erase Memory" function of the Data Overwrite Security is set to on but it cannot be done.
• Data Overwrite Security option SD card is broken.
• Data Overwrite Security option SD card has been removed.
• If the SD card is broken, prepare a new Data Overwrite Security option SD card and replace the NVRAM.
• If the SD card has been removed, turn the main power off and reinstall a working Data Overwrite Security option SD card.
No.
SC878-00
Type
D
Error Name/Error Condition/Major Cause/Solution
TPM authentication error
TPM electronic recognition failure
• Update of system module attempted without correct update path
• USB flash memory not operating correctly
Replace the controller board.
Trusted Platform Module
• In computing, Trusted Platform Module (TPM) is both the name of a published specification detailing a secure crypto processor that can store cryptographic keys that protect information, as well as the general name of implementations of that specification often called the "TPM chip" or
"TPM Security Device" (as designated in certain Dell BIOS settings).
No.
SC878-01
Type
D
Error Name/Error Condition/Major Cause/Solution
USB flash error
There is a problem in the file system of the USB flash memory.
USB Flash system files corrupted
Replace the controller board.
955
956
6. Troubleshooting
No.
SC878-02
Type
D
Error Name/Error Condition/Major Cause/Solution
TPM error
An error occurred in either TPM or the TPM driver
TPM not operating correctly
Replace the controller board.
No.
SC878-03
Type
D TCSD error
Error Name/Error Condition/Major Cause/Solution
An error occurred in the TPM software stack.
• TPM, TPM software cannot start
• A file required by TPM is missing
Replace the controller board.
No.
SC878-20
Type
D
Error Name/Error Condition/Major Cause/Solution
Random number test error
An error was detected when a random number table was generated during a self-test. The random number table is generated by TPM (Trusted
Platform Module). The table generated by TPM failed the test.
• TPM (Trusted Platform Module) is a computer chip that can securely store information used to authenticate the platform. This information can include passwords, certificates, and encryption keys.
TPM is defective
• Turn the main power OFF/ON.
• Replace the controller board.
Service Call 816-899
No.
SC880-00
Type
D
Error Name/Error Condition/Major Cause/Solution
MLB error
Reply to MLB access was not returned within a specified time.
MLB defective
• Replace the MLB.
• Remove the MLB.
No.
SC881-01
Type
D
Error Name/Error Condition/Major Cause/Solution
Management area error
• A problem was detected in the software
• This error may even occur is an IC card option is not installed.
• This is caused by accumulation of abnormal authentication information in the software. (User operation will not directly cause it.)
• At login
Example: When a job is sent to the printer/when logged on from the operation panel/when logged on from a Web browser
Turn the main power OFF/ON.
No.
SC899-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Software performance error (signal reception end)
Unknown software error occurred.
Occurs when an internal program behaves abnormally.
In the case of a hardware defect
• Replace the hardware.
In the case of a software error
• Turn the main power OFF/ON.
• Try updating the firmware.
957
958
6. Troubleshooting
SC No.
SC995-01
Type
D
Error Name/Error Condition/Major Cause/Solution
CPM setting error 1
Comparison of machine serial number (11 digits) and machine identification code.
Details:
• Machine serial number cannot be identified because of BICU replacement or malfunctioning.
• Machine serial number cannot be identified because of NV-RAM replacement
Machine serial number (11 digits) or machine identification code does not match.
• Enter the machine serial number using SP5-811(MachineSerial), and then turn the power on/off.
• Attach the NV-RAM that was installed previously.
SC No.
SC995-02
Type
D
Error Name/Error Condition/Major Cause/Solution
CPM setting error 2
Comparison of machine serial number (11 digits) and machine identification code.
Details:
Machine serial number cannot be identified because of NV-RAM replacement or malfunctioning.
Machine serial number (11 digits) or machine identification code does not match.
• Attach the NV-RAM that was installed previously.
• Download data on the NV-RAM using SP5-825 (NV-RAM Data
Download).
Service Call 900-998
SC No.
SC995-03
SC No.
SC995-04
Type
D
Error Name/Error Condition/Major Cause/Solution
CPM setting error 3
Comparison of machine serial number (11 digits) and machine identification code.
Details:
Unable to recognize machine identification code because the controller was replaced incorrectly or is malfunctioning.
Machine serial number (11 digits) or machine identification code does not match.
Replace it with a specified controller.
Type
D
Error Name/Error Condition/Major Cause/Solution
CPM setting error 4
Comparison of machine serial number (11 digits) and machine identification code.
Machine serial number (11 digits) or machine identification code does not match.
Return the parts to the original configuration, and then replace them according to the manual.
959
960
6. Troubleshooting
SC No.
SC900-00
Type
A
Error Name/Error Condition/Major Cause/Solution
Electric counter error
The electric total counter value is out of specification.
Error is detected when increasing the total counter.
• Unexpected NV-RAM is attached.
• NV-RAM defective
• NV-RAM data corrupted.
• Data written to unexpected area because of external factor etc.
• The count requested by the SRM on receiving PRT is not completed.
Replace the NV-RAM.
SC No.
SC910-01
SC910-02
SC910-03
Type
C
C
C
Error Name/Error Condition/Major Cause/Solution
External controller error 1
External controller error 2
External controller error 3
-01
The external controller receives the unexpected command from the engine side.
-02
The external controller wrongly receives the command from the engine side.
-03
The external controller receives the engine status out of specification.
Refer to the instructions for the external controller
Turn the main power OFF/ON.
Service Call 900-998
SC No.
SC910-10
SC No.
SC919-00
SC No.
SC920-02
SC920-04
Type
C
Error Name/Error Condition/Major Cause/Solution
External controller error 1
The external controller error is detected due to other reason shown in
SC910-01 to -03.
Refer to the instructions for the external controller
Turn the main power OFF/ON.
Type
D
Error Name/Error Condition/Major Cause/Solution
External controller down
While EAC (External Application Converter), the conversion module, was operating normally, the receipt of a power line interrupt signal from the FLUTE serial driver was detected, of
BREAK signal from the other station was detected.
External controller and the machine had been operating correctly (*) but the external controller was turned off or rebooted, or the video bus was disconnected.
* Printing or scanning using the external controller.
Turn the main power OFF/ON.
Type
B
B
Error Name/Error Condition/Major Cause/Solution
Printer application error (WORK memory cannot be acquired)
Printer application error (Filter process ended abnormally)
An error was detected in the application, and no further operation is possible.
• There is a bug in the software.
• The hardware configuration is not as planned (for example, insufficient memory).
• Turn the main power OFF/ON.
• Increase the memory storage capacity.
961
962
6. Troubleshooting
SC No.
SC921-00
SC No.
SC925-00
SC925-01
Type
B
Error Name/Error Condition/Major Cause/Solution
Printer application error (Resident font not found)
The resident fonts cannot be found at printer startup.
The resident font file is missing.
Turn the main power off/on.
Type
B
B
Error Name/Error Condition/Major Cause/Solution
NetFile function error
NetFile function error
The NetFile file management on the HDD cannot be used, or a NetFile management file is corrupted and operation cannot continue.
• HDD defective
• HDD inconsistency caused by power failure during HDD access, etc.
• Software bug
Service Call 900-998
SC No.
SC No.
SC990-00
Type Error Name/Error Condition/Major Cause/Solution
If another SC related to HDD errors (SC860 to SC865) is issued at the same time, the HDD is the cause. Solve the other SC.
• If SC860 to SC865 is not issued
• Turn the main power off/on.
• If this does not work, initialize the HDD NetFile partition
(SP5-832-011: HDD Formatting (Ridoc I/F)). Approval by the customer is required because received fax message waiting to be delivered and documents waiting to be captured will be lost.
Procedure:
1. Go into the User Tools mode and do "Delivery Settings" to print all received fax documents that are scheduled for delivery.
Then erase them.
2. In the User Tools mode, do Document Management> Batch
Delete Transfer Documents.
3. Do SP5-832-011, then turn the machine power off and on.
• If this does not solve the problem, initialize all partitions of the
HDD (SP5-832-001: HDD Formatting (ALL)), then turn the machine power off and on.
Approval by the customer is required because documents and
Address Book information in the HDD will be lost. Received fax messages stored are protected but the order may be changed.
• If this does not solve the problem, replace the HDD.
Type
D
Error Name/Error Condition/Major Cause/Solution
Software operation error
Software attempted an unexpected operation.
• Parameter error
• Internal parameter error
• Insufficient work memory
• Operation error caused by abnormalities that are normally undetectable.
• Turn the main power off/on.
• Reinstall the software of the controller and BCU board.
963
964
6. Troubleshooting
SC No.
SC991-00
SC No.
SC992-00
SC No.
SC994-00
Type
C
Error Name/Error Condition/Major Cause/Solution
Recoverable software operation error
Software attempted an unexpected operation.
SC991 covers recoverable errors as opposed toCS990.
• Parameter error
• Internal parameter error
• Insufficient work memory
• Operation error caused by abnormalities that are normally undetectable.
Logging only
Type
D
Error Name/Error Condition/Major Cause/Solution
Undefined SC issued.
An SC, that is not controlled by the system, occurred.
• An SC for the previous model was used mistakenly, etc.
• Basically a software bug.
Turn the main power OFF/ON.
Type
C
Error Name/Error Condition/Major Cause/Solution
Operation error caused by abnormalities that are normally undetectable.
An error occurred because the number of records exceeded the limit for images managed in the service layer of the firmware.
This can occur if there are too many application screens open on the operation panel.
Logging only.
Service Call 900-998
SC No.
SC997-00
SC No.
SC998-00
Type
D
Error Name/Error Condition/Major Cause/Solution
Application function selection error
The application selected by the operation panel key operated abnormally (No response, abnormal ending).
Software bug (mainly the application)
• Check the optional RAM, DIMM, boards required by the application program.
• Check if the combination of downloaded programs are correct.
Type
D
Error Name/Error Condition/Major Cause/Solution
Application start error
• No application was registered to system within a specified time after the main power was turned on.
(No application starts/All applications have been terminated abnormally)
• Application started but cannot be drawn now for some reason.
• Software bug (mainly the application)
• The optional RAM, DIMM, boards required by the application program. Are not installed correctly.
• Turn the main power OFF/ON.
• Check the optional RAM, DIMM, boards
• Check the combination of programs
• Replace the controller board.
965
966
6. Troubleshooting
• The ID sensor cannot detect the MUSIC pattern
• Color registration error is larger than the specified value
[Assumed Cause]
1. Large drifting
"Large drifting" is the state where the color registration error is larger than the specified value.
In the "Large drifting" state, the MUSIC pattern is shifted a long distance in the main scan direction
(side to side), and is moved to the position where the MUSIC Sensor (TM/ID sensor) cannot be detected, or each pattern cannot be detected due to the pattern overlapping.
2. MUSIC pattern density error
Pattern with the lower density
3. Defective Image transfer belt/Image transfer unit
• Belt scratched
• Belt corrugation, belt skew
• Cleaning failure
• Background stains
• Filming
"Filming" is a phenomenon where surface properties change over time.
Glossiness is one of the surface properties. In the "Filming" state, the whole or part (belt shaped) of the Image Transfer Belt surface becomes foggy. "Filming" changes reflected light, and the MUSIC Sensor (TM/ID sensor) may detect the input wrongly, which causes an error.
4. MUSIC sensor (TM/ID sensor) defective
• Connector/ harness disconnected
• Sensor surface dirty
• Sensor malfunction
• BCU malfunction
5. Paper transfer contact/release mechanism defective
• Connector/ harness disconnected
• Motor/ sensor malfunction
Troubleshooting for SC Errors
• Imaging IOB malfunction
6. Laser optics positioning motor in laser unit defective
• Connector/ harness disconnected
• Motor malfunction
• Imaging IOB malfunction
As SC285-02 is a logging SC (SC Type C), it is not displayed at once when an error occurs. Though the equipment can be operated, check the SC history and perform a recovery operation if the SC has occurred.
967
6. Troubleshooting
968
Countermeasure (1): Large drifting
An abnormal value may be contained in the SP where the MUSIC corrected result is saved.
1. Execute SP2-180-001 (Line Pos. Adj.: Clear Color Regist.).
2. Execute SP2-111-004 (Forced Line Position: Adj. Mode d).
3. Execute SP2-194-007 (MUSIC Execution Result: Execution Result).
Countermeasure (2): MUSIC pattern density Error
Execute MUSIC and check the result.
Troubleshooting for SC Errors
1. Execute SP3-011-001 (Manual ProCon :Exe : Normal ProCon).
2. Execute SP2-111-004 (Forced Line Position: Adj. Mode d).
3. Execute SP2-194-007 (MUSIC Execution Result: Execution Result).
Countermeasure (3): Image transfer belt/ Image transfer unit defective
1. Execute SP2-112-001 (TM/ID Sensor Check Execute).
2. Check SP2-112-010 (TM/ID Sensor Test General:FCR).
• Normal If the result is "111"
-->Execute other countermeasures.
• Vsg adjustment is failed if the result is "2xx", "x2x", or "xx2"
-->Execute recovery operation for SC370
• There is a high probability that contaminants, scars, or irregularities may exist on the belt if the result is "3xx", "x3x", or "xx3"
-->Execute the following procedure;
1. Remove the image transfer unit, and check for abnormalities such as contaminants or scars, and set it after cleaning.
2. Execute SP2-111-004 (Forced Line Position: Adj. Mode d).
3. Execute SP2-194-007 (MUSIC Execution Result: Execution Result).
4. If it fails, replace the image transfer belt/ Image transfer unit.
• There is a high probability that contaminants or curls may exist on the belt if the result is
"5xx", "6xx", "7xx", "8xx", "x5x", "x6x", "x7x", "x8x", "xx5", "xx6", "xx7", or "xx8".
--> Execute the following procedure
1. Remove the Image Transfer Unit, and check for abnormalities such as contaminants or scars, and set it after cleaning.
2. Execute SP2-111-004 (Forced Line Position: Adj. Mode d).
3. Execute SP2-194-007 (MUSIC Execution Result: Execution Result).
4. If it fails, replace the image transfer belt/ Image transfer unit.
Countermeasure (4): TM/ID sensor defective
Follow the next step if executing SP2-111-004 (Forced Line Position: Adj. Mode d) and
SP2-194-007 (MUSIC Execution Result: Execution Result) fails.
1. Clean the TM/ID Sensor.
2. Check the harness and connector for TM/ID sensor.
3. Replace the TM/ID sensor.
4. Replace the BCU.
969
6. Troubleshooting
970
Countermeasure (5): Paper transfer contact/release mechanism defective
Check if the MUSIC/ProCon Pattern is attached on the Paper Transfer Roller. If it is attached, separating may be defective.
1. Execute SP5-804-255 (OUTPUT Check: Paper Transfer Contact Operation) to operate the paper transfer contact and release motor to check the separating operation of the paper transfer roller.
2. Check for a broken harness or connector disconnection.
3. If the problem cannot be solved, replace the Imaging IOB.
Countermeasure (6): Laser optics positioning motor in laser unit error
1. Check the operation of the laser optics positioning motor and check for a broken harness or connector disconnection. If an abnormality is detected, replace the Laser Unit.
2. If the problem cannot be solved, replace the Imaging IOB.
• TM (ID) sensor connector missing/connection error
• TM (ID) sensor detection window dirt
• TM (ID) sensor malfunction
• Undulation in the ITB, or belt slippage
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps.
1. Check if all connectors related to TM/ID sensor are connected securely. Reconnect the connectors if they are disconnected, or loose.
2. If TM/ID sensor is contaminated, clean it with dump cloth (never use a dry cloth or alcohol).
3. Check if there is an abnormality on the image transfer belt surface.
4. If any abnormalities are found on the image transfer belt surface, replace the image transfer belt.
• Belt scratched
• Belt corrugation, belt skew
• Cleaning failure
• Background stains
• Filming
Troubleshooting for SC Errors
5. Check the TM/ID sensor for malfunctions, and recover or replace it if there are any defects.
6. Check the harness. Replace the harness if it is disconnected, or damaged.
7. If the SC is not cleared even after performing steps 1 to 6, replace the BCU
1. Execute Vsg adjustment with SP3-320-001(Vsg Adj: Execute :P Sensor).
2. Check the result with SP3-323-001(Vsg Adj OK?: Latest).
• If code is "1": Recovered
• If code is not "1": Not recovered
After performing recovery on SC370, execute the following adjustment procedures.
1. Execute SP2-111-004 (Forced Line Position: Adj. Mode d).
2. Execute the following SPs and check the results:
• SP2-194-007 (Execution Result)
• SP2-194-010 (Error Result: C)
• SP2-194-011 (Error Result: M)
• SP2-194-012 (Error Result: Y)
Execute result sample
Factory default: 0
Success: 1
3. Execute SP3-011-001 (Manual ProCon :Exe).
4. Execute the following SPs and check the results.
• SP3-012-001 to 010 (Front)
• SP3-012-011 to 020 (Center)
• SP3-012-021 to 030 (Rear)
Execute result sample (In order of YMCK from left)
• Factory default:[00,00,00,00]
• Starting adjust:[99,99,99,99]
• Fail Vsg adjust(Y):[21,99,99,99]
• Error of Development gamma Max(C):[99,99,55,99]
• Succeed:[11,11,11,11]
971
972
6. Troubleshooting
SC501, SC502, SC503, or SC504 occurs.
1.
Pull out the paper feed tray [A] on which the SC has occurred, and then, lifting the front part of the tray, pull it out all the way through (The photograph shows Tray 1.)
2.
Check if there is any paper jammed in the machine, and remove it if there is.
3.
If the sheets exceed the stackable limit, reduce the number of sheets.
Troubleshooting for SC Errors
4.
Reattach the tray. Lift the tray slightly when you attach it.
When SC544-02 or SC554-02 is displayed, the unit is probably damaged. Therefore replace a fusing unit or fusing sleeve belt unit in accordance with the following procedure.
973
6. Troubleshooting
974
To clear SC544-02 or SC554-02, replacing the fusing unit or installing an intact new unit detection fuse in the fusing unit must be required. The intact new unit detection fuse is provided in the fusing sleeve belt unit.
When replacing the fusing sleeve belt unit, follow the procedure below.
SP descriptions
• SP5-810-002 [SC Reset: Hard High Temp. Detection]
Clears the fusing hardware SC.
• SP3-701-115 [Manual New Unit Set: #Fusing Unit]
Troubleshooting for SC Errors
Sets the new unit detection flag ON/OFF.
• SP3-701-116 [Manual New Unit Set: Fusing Belt]
Sets the new unit detection flag ON/OFF.
1.
Install a new fusing sleeve belt unit. (
)
2.
There is a new unit detection fuse packed with the new fusing sleeve belt unit.
3.
Connect the new unit detection fuse to the connector [A], and place the fuse in the empty space [B].
4.
Reattach the fusing unit.
5.
Switch the power ON.
6.
Execute SP5-810-002 [SC Reset: Hard High Temp. Detection].
7.
Set SP3-701-116 [Manual New Unit Set: Fusing Belt] to “1”.
975
976
6. Troubleshooting
8.
Switch the power OFF and ON.
The modules considered to be the cause of SC663, 664, 665, 667, 668 and 670-01 are as follows.
Troubleshooting for SC Errors
The engine board resets at an unexpected time, and does not start up again.
Note: CTL = Controller
SC670-01
Engine start up error when the machine boots up
If the symptom occurs, use the following chart to decide the best course of action.
SC670-02
Engine start up error when the machine is in operation.
Replace the part in order of precedence stated below (since there is a high possibility that those parts are broken and causing the error).
1. Replace BCU
977
978
6. Troubleshooting
2. Replace IPU
3. Replace CTL
4. Replace PSU
SC670-03
IPU start up error when the machine boots up.
Replace the part in order of precedence stated below (since there is a high possibility that those parts are broken and causing the error).
1. Replace IPU
2. Replace CTL
3. Replace PSU
4. Replace BCU.
SC670-04
Communication error between the engine and controller.
Replace the part in order of precedence stated below (since there is a high possibility that those parts are broken and causing the error).
1. Replace IPU
2. Replace BCU
3. Replace CTL
4. Replace PSU
Note: CTL = Controller
The following occur:
SC672-00
SC672-10
SC672-11
SC672-12
Communication error between operation panel and CTL after machine is powered on.
Communication error (receive) between operation panel and CTL after machine is powered on.
Communication error (send) between operation panel and CTL after machine is powered on.
Communication error between operation panel and CTL after normal start-up.
Troubleshooting for SC Errors
SC672-13
Communication error between operation panel and CTL after normal start-up;
Operation panel not detected.
• SC672 does not appear on the SMC report, as it is not logged.
• The Smart Operation Panel communicates with the controller via a USB cable and IPU. SC672 is triggered when the panel cannot communicate with the controller.
Possible causes of SC672 include:
• USB communication path failure (USB cable, IPU)
• CTL boot up error and/or operation panel boot up error due to abnormal break in operations of
CTL.
Possible causes of operation panel cannot light include:
• USB communication path failure (USB cable, IPU)
• Operation panel cannot communicate with CTL due to CTL boot-up error
[A]: Operation Panel
[B]: IPU
[C]: FCU
[D]: Controller
[E]: USB cable
Do the following.
979
6. Troubleshooting
1.
Turn the machine power OFF/ON.
2.
Do the action in the flowchart below to determine the cause and best course of action when SC672 occurs.
• If the SC recurs after you do the action in this flowchart, do the following.
- If SC819 (cache error) appears in the SC history, replace the controller board.
- If SC991 (SCS: scs time count level c’) appears in the SC history, replace the controller board and USB cable.
Flowchart to determine parts to replace when SC672 occurs
980
Parts
USB cable
Operation panel
CTL
Memory
How to determine the cause
LED on CTL blinks for 1 second
LED on CTL blinks for 1 second
LEDs on CTL blink constantly
LEDs on CTL blink constantly
Troubleshooting for SC Errors
Flowchart to determine parts to replace when no display on operation panel
Parts
USB cable
Operation panel
IPU
CTL
Memory
Check the condition (lit, off, blinking) of the LED on the CTL.
LED /POSTCODE AREA on the CTL
How to determine the cause
LED on CTL blinks for 1 second
LED on CTL blinks for 1 second
Fuse 3 on the IPU
LED on CTL does not blink
LED on CTL does not blink
981
6. Troubleshooting
Normal situation: POSTCODE LED 8 and BIOS LED blinking for 1 second
982
LED
No.
Note
For CPU
- POSTCODE 8 and LED16 blink when the CPU is operating normally.
- POSTCODE 8 and LED16 is lit or off when there is a problem with the CPU.
LEDs 1 to 8 blink constantly
Troubleshooting for SC Errors
No.
POSTCOD
E 1-8
LED 16
Note
1. For self-diagnosis code (BIOS).
2. After the BIOS starts up, LEDs 4,5,7 turn off and LEDs 1,2,3 ,6 turn on and LED 8 blinks. LED 8 is lit or off when there is a problem with the CPU.
- LED is lit when the BIOS is running.
- LED blinks when the OS is running.
1. Re-connect the USB cable between IPU board and operation panel.
When connecting the cable, hold the molded part of the cable as shown below so as not to apply excessive force on the connector part. Applying excessive force toward the upper direction on the connector may cause connection failure.
983
6. Troubleshooting
Applied to machines built in October 2016 and later:
A bracket [A] which covers the upper part of the cable will be added.
984
PCB for the operation panel
USB connector [B] (IPU)
1.
Turn the machine power OFF.
2.
Attach the memory on the CTL as shown (in a vertical orientation).
Troubleshooting for SC Errors
985
6. Troubleshooting
3.
Lock the hook.
1.
Turn the machine power OFF.
2.
Turn Dip switch 1-3 ON for 10 seconds
3.
Turn Dip switch 1-3 OFF
4.
Turn the machine power ON.
986
Fuse on the IPU
Troubleshooting for SC Errors
1.
Remove the Platen Cover, or ARDF/SPDF. ( page 429 )
2.
Remove a screw at the scanner right cover.
3.
Remove the scanner right cover [A]
Remove the hook at the upper part, and then slide the cover in the rear direction.
987
988
6. Troubleshooting
4.
Remove the scanner front cover [A]
5.
Remove the scanner left cover [A]
Troubleshooting for SC Errors
6.
Holding down both the sides of the operation panel upper cover [A], unhook the tabs
(indicated by blue circles) and remove the cover.
7.
Remove the USB cable connector [A] ( x1, x2).
8.
Remove the two screws ( x2).
989
6. Troubleshooting
9.
Remove the two connectors ( x2).
10.
Remove the scanner unit [A] ( x11).
990
• Never loosen or remove the following screw when you remove or re-attach the unit. This screw fixes the scanner cam in place. If the position of the scanner cam changes, the scanner will be misaligned. This will result in image skew and other image alignment issues.
11.
Remove the USB cable ( x5)
Applied to machines built in May 2016 and later:
A clamp on the IPU [A] will be added.
Troubleshooting for SC Errors
• Make sure that there is no space between the machine frame and the following three areas of the scanner unit when you re-attach the scanner unit.
991
6. Troubleshooting
992
If the symptom is not resolved, escalate the issue using the normal process, together with the following information for further investigation.
• SC sub code (SC672-10 or 99)
• Date/time of problem occurrence
• Factor(s) that trigger the problem (ex. SC672-11 occurred 3 minutes after tuning ON the main power switch.)
• Occurrence frequency (ex. One out of ten times when turning ON the main power switch)
• Parts replaced
• Date/time when parts were replaced
When Abnormal Noise Occurs
When abnormal noise occurs during machine operating, identify the occurrence location, by using various OUTPUT Check. However, about the following two modules, follow the checking procedure flow.
• Check the abnormal noise of the drive unit (peripheral fusing)
• Check the abnormal noise when the toner is supplied or the bottle motor is driving
• Because the damage or contamination of parts can lead to secondary failure, always follow the procedure.
• Take particular care not to be caught in the rotating parts of the motors and/or gears.
When the abnormal noise of drive unit (peripheral fusing) has occurred, follow the following flow, and check whether the fusing unit is the cause, by using SP1-153 (Abnormal Noise Confirmation).
If the fusing unit is the cause, replace the fusing unit. If the drive module is the cause, in addition perform the operation check of various motors by using OUTPUT Check, to identify which motor is the cause.
993
6. Troubleshooting
994
About the setting value of the operation line speed in SP1-153-003
During warming-up or operating on the operation panel, the motors rotate at low line speeds. At the time, if noise occurs, start checking from [2: Low Speed]. Middle speed is for only thick paper 1 printing, so use middle speed if abnormal noise occurs when thick paper 1 is supplied.
Related SP
SP No.
SP Name Function Description
The fusing motor rotates with the heating control.
SP1-153-001 Abnormal Noise
Confirmation: Unit:
Execute
SP1-153-002 Abnormal Noise
Confirmation: No Unit:
Execute
The fusing motor rotates without the fusing unit.
Fails if the fusing unit is not installed or the cover is open
Fails if the fusing unit is installed or the cover is open
When Abnormal Noise Occurs
SP No.
SP Name
SP1-153-003 Abnormal Noise
Confirmation: Operation
Line Speed
SP1-153-004 Abnormal Noise
Confirmation: Operation
Time
Function
Line speed at the time of rotation
0: Standard speed
1: Middle speed
2: Low speed
Rotates during this time. Initial value: 60 sec.
Temperature setting for
SP1-153-001 (Unit: Execute)
SP1-153-005 Abnormal Noise
Confirmation: Heat
Center Target Temp
SP1-153-006 Abnormal Noise
Confirmation: Heat End
Target Temp
SP1-153-007 Abnormal Noise
Confirmation: Press
Target Temp
Temperature setting for
SP1-153-001 (Unit: Execute)
Temperature setting for
SP1-153-001 (Unit: Execute)
Description
Do not change
The operation check of the toner supply motor and/or toner bottle drive motor, is performed by a forced toner supply, not OUTPUT Check.
• Operation other than the following procedures may occur the abnormal density, toner scattering, scumming, and cleaning failure at the image transfer unit.
1.
Do [Force Tnr Supply :Exe (SP3-050-003 to 006)] for the applicable color twice. If there is enough toner in the toner supply unit, the toner bottle drive motor will not work.
SP No.
SP3-050-003
SP3-050-004
SP3-050-005
SP Name
Force Tnr Supply :Exe Execute: K
Force Tnr Supply :Exe Execute: C
Force Tnr Supply :Exe Execute: M
995
996
6. Troubleshooting
SP No.
SP Name
SP3-050-006 Force Tnr Supply :Exe Execute: Y
2.
Do [Manual ProCon :Exe Density Adjustment (SP3-011-002)] once.
• If the operation of the toner bottle drive motor could not be checked, do step1 again after the manual execution of density adjustment.
When a jam occurs, the cause position will blink.
Jam Detection
• Do not touch any components except the specified parts for removing jammed paper. Some parts can burn you because they become hot during operation.
• Do not turn the power off during removal of jammed paper. If you turned the power off, functions or values that were previously set will be deleted.
• Be sure not to tear paper up, and that you remove all pieces. Remaining scraps of paper in the machine could cause another paper jam or machine failure.
• If there are multiple jam locations, check all the locations that are displayed at the same time.
See the decals on the machine for how to remove jammed paper.
997
6. Troubleshooting
Plotter (print engine) jam history can be displayed using SP7-507.
• SP7-507-001 "Plotter Jam: History Latest"
• SP7-507-002 "Plotter Jam: History Latest1"
• SP7-507-003 "Plotter Jam: History Latest2"
• SP7-507-004 "Plotter Jam: History Latest3"
• SP7-507-005 "Plotter Jam: History Latest4"
• SP7-507-006 "Plotter Jam: History Latest5"
• SP7-507-007 "Plotter Jam: History Latest6"
• SP7-507-008 "Plotter Jam: History Latest7"
• SP7-507-009 "Plotter Jam: History Latest8"
• SP7-507-010 "Plotter Jam: History Latest9"
998
• CODE: Indicates the jam code.
• SIZE: Indicates the paper size code.
• TOTAL: Indicates the total counter (SP7-502-001).
• DATE: Indicates the date when the jam occurred.
• The jam history of the 10 latest jams is displayed.
• The first jam is not included in the history record.
• Cause code: Jam cause code displayed by log data
Jam Detection
• Display code: Jam position displayed on control panel
Late jam
The paper has failed to arrive within the prescribed time due to a jam that has occurred upstream of the referenced sensor.
Lag jam
The paper has failed to leave the location of the referenced sensor within the prescribed time due to a jam downstream of the referenced sensor.
Stay jam
The paper is within the location of the referenced sensor.
ARDF DF3090
Cause code Cause of jam
Late
Jam
Lag
Jam
Stay
Jam
Display code
014 Skew Correction Sensor P
064
016
066
017
Skew Correction Sensor
Registration Sensor
Registration Sensor
Exit Sensor
P
P
P
P
067
239
Exit Sensor
Misfeed: Original Removed
P
P
SPDF DF3100
Cause code Cause of jam
Late
Jam
Lag
Jam
Stay
Jam
013
063
014
064
015
065
Separation Sensor
Separation Sensor
Skew Correction Sensor
Skew Correction Sensor
Pre-Scanning Entrance Sensor
Pre-Scanning Entrance Sensor
Display code
P
P
P
P
P
P
999
1000
6. Troubleshooting
Cause code Cause of jam
001
001
003
004
008
009
001
001
001
001
001
001
001
016
066
017
067
239
001
001
Main Machine
Cause code
Registration Sensor
Registration Sensor
Exit Sensor
Exit Sensor
Misfeed: Original Removed
Initial jam
Overload jam
Cause of jam
Transport Sensor 1
Transport Sensor 2
Registration Sensor
Fusing Entrance Sensor
Fusing Exit Sensor
Paper Exit Sensor
Reverse Sensor
Duplex Exit Sensor
Duplex Entrance Sensor
Paper not fed from tray 1
Paper not fed from tray 2
Paper not fed from bypass tray
Paper not transported to duplex unit
Late
Jam
Lag
Jam
Stay
Jam
Display code
P
P
P
P
P
P
P
Late
Jam
Lag
Jam
Stay
Jam
Z
Z
A1
C
C
Display code
A
A
B
C
C
A2
A
Z
Jam Detection
011
012
017
018
019
020
Cause code
096
051
052
048
057
060
024
064
025
025
065
027
027
067
Cause of jam
Disappearance of the detection Timing
Only remaining paper position information displayed
Transport Sensor 1
Late
Jam
Transport Sensor 2
Registration Sensor
Fusing Entrance Sensor
Fusing Exit Sensor
Paper Exit Sensor
Transport Sensor 1 (when paper not fed from Tray 1)
Transport Sensor 2
Transport Sensor 1 (when paper not fed from Bypass Tray)
Registration Sensor
Paper Exit Sensor
Reverse Sensor
Reverse Sensor
Duplex Exit Sensor
Duplex Exit Sensor & No Paper at Duplex
Entrance Sensor
Duplex Exit Sensor
Duplex Entrance Sensor
Duplex Entrance Sensor & No Paper at
Reverse Sensor
Duplex Entrance Sensor
Lag
Jam
Stay
Jam
Display code
A
A
Z
C
Z
A
B
C
C
A
A
A
A
B
C
C
C
Z
Z
1001
1002
6. Troubleshooting
Paper Feed Unit PB3150
Cause code Cause of jam
005
013
053
001
Paper not fed from tray 3
Vertical Transport Sensor (Tray 3)
Vertical Transport Sensor (Tray 3)
Vertical Transport Sensor (Tray 3)
Paper Feed Unit PB3220/PB3210
Cause code Cause of jam
005
013
053
001
006
014
054
001
Paper not fed from tray 3
Vertical Transport Sensor (Tray 3)
Vertical Transport Sensor (Tray 3)
Vertical Transport Sensor (Tray 3)
Paper not fed from tray 4
Vertical Transport Sensor (Tray 4)
Vertical Transport Sensor (Tray 4)
Vertical Transport Sensor (Tray 4)
Bridge Unit BU3070
Cause code Cause of jam
021
022
061
062
Paper Exit Sensor (Bridge Unit)
Relay Transport Sensor (Bridge Unit)
Paper Exit Sensor (Bridge Unit)
Relay Transport Sensor (Bridge Unit)
Late
Jam
Lag
Jam
Stay
Jam
Display code
Y1
Y
Y
Y
Late
Jam
Lag
Jam
Stay
Jam
Y
Y
Y
Display code
Y1
Y
Y
Y
Y2
Late
Jam
Lag
Jam
Stay
Jam
Display code
D
D
D
D
Jam Detection
Internal Finisher SR3130
Cause code Cause of jam
Lag
Jam
112
113
114
115
116
108
109
110
111
104
105
106
107
100
101
102
103
148
149
Inlet Sensor
Inlet Sensor
Transport sensor
Transport sensor
Paper Exit Unit
Jogger fence motor (front)
Jogger fence motor (rear)
Shift Roller Motor
Positioning Roller Motor
Paper Exit Guide Plate Open/Close Motor
Stapler Retreat Motor
Shift Tray Ascent/Descent Motor
Stapler Motor
Paper Press Motor
Punch Motor
Punch Displacement Motor
Horizontal Registration Displacement
Motor
Paper exit end not responding
Main instruction data defect
Booklet Finisher SR3220
Cause code Cause of jam
Late
Jam
Lag
Jam
200 Paper Entrance
Late
Jam
Stay
Jam
Stay
Jam
R1-R2
R1-R2
Display code
R1-R4
R1-R2
R1-R2
R1-R2
R1-R2
R1-R2
R1-R2
R1-R2
R1-R2
R1-R2
Display code
R1-R2
R1-R2
R1-R2
R1-R2
R1-R2
R1-R2
R1-R2
R1-R2
1003
1004
6. Troubleshooting
223
224
225
226
227
228
229
Cause code
212
213
220
221
222
208
209
210
211
201
202
203
204
205
206
207
Cause of jam
Paper Entrance
Proof Exit
Proof Exit
Intermediate transport (right)
Intermediate transport (left)
Intermediate transport (left)
Shift Exit
Shift Exit
Stack Transport
Rear Edge Stopper Transport
Rear Edge Stopper Transport
Paper did not reach middle folding exit
Middle Folding exit
Jam in inlet transport motor
Jam in proof transport motor
Jam in exit transport/positioning/approach roller motor
Jam in shift motor
Jam in jogger motor
Jam in exit guide plate open/close motor
Jam release motor
Jam in tray ascent/descent motor
Jam in positioning roller motor
Jam in stapler retreat motor
Late
Jam
Lag
Jam
Stay
Jam
Display code
R1-R4
R5-R10
R5-R10
R5-R10
R5-R10
R5-R10
R1-R4
R1-R4
R1-R4
R1-R4
R1-R4
R1-R4
R1-R4
R1-R4
R1-R4
R1-R4
R1-R4
R1-R4
R1-R4
R1-R4
R1-R4
R1-R4
R1-R4
Jam Detection
Cause code Cause of jam
306
307
348
300
301
302
303
304
305
230
231
232
233
234
235
236
237
238
248
249
Jam in stapler motor
Jam in punch system motor
Jam in stack transport motor
Jam in rear edge stopper motor
Jam in folding brade motor
Jam in paper exit guide drive motor
Jam in stapleless stapler transfer motor
Jam in staple motor (stapleless)
Jam in paper guide motor
Paper exit end is not responding
Main instruction data defect
Internal Finisher SR3180
Cause code Cause of jam
Entrance sensor
Entrance sensor
Paper exit sensor
Paper exit sensor
Shift motor
Junction gate motor
Paper exit pressure release motor
Stapler motor
Paper exit end not responding
Late
Jam
Lag
Jam
Stay
Jam
Display code
R1-R4
R1-R4
R5-R10
R5-R10
R5-R10
R1-R4
R1-R4
R1-R4
R1-R4
R1-R4
R1-R4
Late
Jam
Lag
Jam
Stay
Jam
Display code
R
R
R
R
R
R
R
R
R
1005
1006
6. Troubleshooting
Size Code
005
006
014
038
044
132
133
134
A4 LEF
A5 LEF
B5 LEF
LT LEF
HLT LEF
A3 SEF
A4 SEF
A5 SEF
Paper Size Size Code
141
142
160
164
166
172
255
B4 SEF
B5 SEF
DLT SEF
LG SEF
LT SEF
HLT SEF
Others
Paper Size
Jam Detection
1007
1008
6. Troubleshooting
Make sure that the following SPs are set to their default values, and keep them at these values at all time.
• SP1-113-001 (Curl Correction): Keep at default value of 0 (OFF)
This is because printing productivity drops to about 65 to 80% when this SP is ON. It is not effective in reducing curl on these models.
• SP1-115-xxx (Print Target Temp): Keep at default value.
This is because fusing offset may occur when the fusing temperature is reduced. This SP is not effective for improving image quality on these models.
Solution:
Installing the tray heaters for the mainframe paper bank and optional paper banks. (page 119 "Anti-
Condensation Heater for Paper Feed Trays")
If the error occurs periodically, do the following steps. If the result is as shown in the "Problem
Judgement" column, follow the solutions.
Target Part/SP No.: Transport Sensor (1st Feed Tray) / SP5-803-003 (Transport Sensor 1)
Cause verification Problem Judgement
0: Paper detected Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
Troubleshooting for Transport/Paper Feeding of the Machine
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.: Transport Sensor (2nd Feed Tray) / SP5-803-005 (Transport Sensor 2)
Cause verification Problem Judgement
0: Paper detected Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.: Registration Sensor / SP5-803-001
Cause verification
Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
Problem Judgement
0: Paper detected
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
1009
1010
6. Troubleshooting
Target Part/SP No.: Fusing Entrance Sensor / SP5-803-006
Cause verification
Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
Problem Judgement
0: Paper detected
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.: Fusing Exit Sensor / SP5-803-007
Cause verification
Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
Problem Judgement
0: Paper detected
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.: Paper Exit Sensor / SP5-803-008
Cause verification
Execute an INPUT check when there is no paper at the position of the referenced sensor.
Problem Judgement
0: Paper detected
Troubleshooting for Transport/Paper Feeding of the Machine
Execute an INPUT check when there is paper at the position of the referenced sensor.
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.: Reverse Sensor / SP5-803-009 (Inverter Sensor)
Cause verification Problem Judgement
0: Paper detected Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.: Duplex Entrance Sensor / SP5-803-011
Cause verification
Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
Solution:
• Clean the sensor.
Problem Judgement
0: Paper detected
1: Paper not detected
1011
6. Troubleshooting
1012
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.: Duplex Exit Sensor / SP5-803-010
Cause verification
Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Problem Judgement
0: Paper detected
1: Paper not detected
If the error occurs periodically, do the following steps. If the result is as shown in the "Problem
Judgement" column, follow the solutions.
Target Part/SP No.:Bypass/Duplex motor / SP5-804-071 (Duplex Bypass Motor: CW:
Standard Speed)
Cause verification Problem Judgement
Turn the referenced motor OFF with OUTPUT
Turn the referenced motor ON with OUTPUT
Drive sound heard
Drive sound not heard
Solution:
• Reconnect the connector.
• Replace the motor.
Troubleshooting for Transport/Paper Feeding of the Machine
• Replace the Paper Transport IOB.
• Replace the harness.
• Replace the harness.
Checking paper status, pick-up roller, feed roller, and friction roller for bypass tray
Check the paper position (Check whether or not the leading edge of the paper, side paper guide, and end paper guide are positioned according to the manual.)
• Check the paper orientation.
• Turn the paper in the feed tray upside down.
Check if the paper has reached the maximum stackable limit of the side paper guide.
Check if the sheets are stuck to each other due to edge roughness, coating, stain, or temperature.
Reduce the paper to below the stackable limit.
Fan the paper
Check if extra thin paper or thick paper exceeding the supported paper thickness is being used.
Check if the paper thickness and size are detected correctly.
Use a supported paper type.
Check if the paper being used produces a lot of paper dust.
Check if the paper roller is stained with paper dust.
Set the paper thickness and size to the correct value.
Change the paper type (if possible).
Clean the pick-up roller, feed roller, and friction roller for bypass tray.
Target Part/SP No.:Transport Sensor (1st Feed Tray) / SP5-803-003 (Transport Sensor 1)
Cause verification Problem Judgement
Execute an INPUT check when there is no paper at the position of the referenced sensor.
0: Paper detected
Execute an INPUT check when there is paper at the position of the referenced sensor.
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
1013
1014
6. Troubleshooting
• Replace the harness.
Target Part/SP No.:Bypass pick-up Solenoid / SP5-803-016 (Bypass Pickup Solenoid)
Cause verification Problem Judgement
Turn the referenced solenoid OFF with OUTPUT check
Turn the referenced solenoid ON with OUTPUT check
Drive sound heard
Drive sound not heard
Solution:
• Reconnect the connector.
• Replace the solenoid.
• Replace the Paper Transport IOB.
• Replace the harness.
Checking paper status, pick-up roller, feed roller, and friction roller for 1st feed tray
Check the paper position (Check whether or not the leading edge of the paper, side paper guide, and end paper guide are positioned according to the manual.)
• Check the paper orientation.
• Turn the paper in the feed tray upside down.
Check if the paper has reached the maximum stackable limit of the side paper guide.
Check if the sheets are stuck to each other due to edge roughness, coating, stain, or temperature.
Reduce the paper to below the stackable limit.
Fan the paper
Check if extra thin paper or thick paper exceeding the supported paper thickness is being used.
Check if the paper thickness and size are detected correctly.
Use a supported paper type.
Check if the paper being used produces a lot of paper dust.
Set the paper thickness and size to the correct value.
Change the paper type (if possible).
Check if the paper roller is not stained with paper dust.
Clean the pick-up roller, feed roller, and friction roller for 1st feed tray.
Troubleshooting for Transport/Paper Feeding of the Machine
Target Part/SP No.:Transport Sensor (2nd Feed Tray) / SP5-803-005 (Transport Sensor 2)
Cause verification Problem Judgement
Execute an INPUT check when there is no paper at the position of the referenced sensor.
0 :Paper detected
Execute an INPUT check when there is paper at the position of the referenced sensor.
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Checking paper status, pick-up roller, feed roller, and friction roller for 2nd feed tray
Check the paper position (Check whether or not the leading edge of the paper, side paper guide, and end paper guide are positioned according to the manual.)
• Check the paper orientation.
• Turn the paper in the feed tray upside down.
Check if the paper has reached the maximum stackable limit of the side paper guide.
Check if the sheets are stuck to each other due to edge roughness, coating, stain, or temperature.
Reduce the paper to below the stackable limit.
Fan the paper.
Check if extra thin paper or thick paper exceeding the supported paper thickness is being used.
Check if the paper thickness and size are detected correctly.
Use a supported paper type.
Check if the paper being used produces a lot of paper dust.
Set the paper thickness and size to the correct value.
Change the paper type (if possible).
Check if the paper roller is not stained with paper dust.
Clean the pick-up roller, feed roller, and friction roller for 2nd feed tray.
1015
1016
6. Troubleshooting
Target Part/SP No.:Registration Sensor / SP5-803-001
Cause verification
Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
Problem Judgement
0 :Paper detected
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Checking paper status, or 1st paper transport roller.
Check if extra thin paper or thick paper exceeding the supported paper thickness is being used.
Check if the paper thickness and size are detected correctly.
Check if the paper feed tray is not stained with a lot of paper dust.
Use a supported paper type.
Set the paper thickness and size to the correct value.
Clean the 1st transport roller.
Target Part/SP No.:Fusing Entrance Sensor / SP5-803-011
Cause verification
Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
Problem Judgement
0 :Paper detected
1: Paper not detected
Solution:
• Clean the sensor.
Troubleshooting for Transport/Paper Feeding of the Machine
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.: PCU Motor: Black / ITB Drive Motor / SP5-804-136 (Transfer Drum Motor
K: Standard Speed)
Cause verification Problem Judgement
Turn the referenced motor OFF with OUTPUT check
Turn the referenced motor ON with OUTPUT check
Drive sound heard
Drive sound not heard
Solution:
• Reconnect the connector.
• Replace the motor.
• Replace the Imaging IOB.
• Replace the harness.
Checking paper jam, or paper transfer unit
Check if there is no double feeding.
Check the edges of the discharge plate to see if it is deformed or broken.
Fan the paper.
Reattach or replace the discharge plate.
Target Part/SP No.:Fusing Exit Sensor / SP5-803-011 (Duplex Entrance Sensor)
Cause verification Problem Judgement
0 :Paper detected Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
1017
6. Troubleshooting
1018
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.: Fusing Motor / SP5-804-092 (Fusing Motor: CW: Standard Speed)
Cause verification Problem Judgement
Turn the referenced motor OFF with OUTPUT check Drive sound heard
Turn the referenced motor ON with OUTPUT check Drive sound not heard
Solution:
• Reconnect the connector.
• Replace the motor.
• Replace the Imaging IOB.
• Replace the harness.
Checking paper jam, or paper transfer unit
Check if there is double feeding.
Check if the margin of the leading edge of paper is too narrow.
Fan the paper.
Adjust the margin at the leading edge of paper with SPs.
Check if the paper is a non-recommended type, e.g., inkjet paper. Replace the paper.
Check if the gap between the fusing stripper plate and fusing belt is too wide, caused by deformation of the plate.
Replace the fusing stripper plate.
Clean the fusing belt.
Check if there is toner and/or paper dust on the surfaces of the fusing belt and pressure roller.
Check if the setting values, e.g. fusing temperature, are higher than the initial values.
Reset the SP values to the initial values.
Target Part/SP No.: Paper Exit Sensor / SP5-803-008
Cause verification
Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
Problem Judgement
0 :Paper detected
1: Paper not detected
Troubleshooting for Transport/Paper Feeding of the Machine
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.:Paper Exit Solenoid / SP5-804-004 (Exit Junction Solenoid)
Cause verification Problem Judgement
Turn the referenced solenoid OFF with OUTPUT check Drive sound heard
Turn the referenced solenoid ON with OUTPUT check Drive sound not heard
Solution:
• Reconnect the connector.
• Replace the solenoid.
• Replace the Paper Transport IOB.
• Replace the harness.
Checking paper jam, or paper status
Check if the leading edge of the paper and the paper feed guide are wet.
Check if the paper is curled too much.
If condensation has occurred inside the machine, leave the machine idle for a few minutes to remove condensation.
If the paper is curled too much, switch on the anti-condensation heater for paper tray.
Use a supported paper type.
Check if extra thin paper or thick paper exceeding the supported paper thickness is being used.
Check if the paper thickness and size are detected correctly.
Set the paper thickness and size to the correct value.
1019
6. Troubleshooting
1020
Target Part/SP No.:Transport Sensor (1st Feed Tray) / SP5-803-003 (Transport Sensor 1)
Cause verification Problem Judgement
0 :Paper detected Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.:Paper Feed Motor / SP5-804-016 (Feed Motor:CW:Standard Speed)
Cause verification Problem Judgement
Turn the referenced motor OFF with OUTPUT check
Turn the referenced motor ON with OUTPUT check
Drive sound heard
Drive sound not heard
Solution:
• Reconnect the connector.
• Replace the motor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.: Transport Motor / SP5-804-028
Cause verification
Turn the referenced motor OFF with OUTPUT check
Turn the referenced motor ON with OUTPUT check
Solution:
• Reconnect the connector.
• Replace the motor.
Problem Judgement
Drive sound heard
Drive sound not heard
Troubleshooting for Transport/Paper Feeding of the Machine
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.:Reverse Motor / SP5-804-047 (Inverter Motor:CW:Standard Speed)
Cause verification Problem Judgement
Turn the referenced motor OFF with OUTPUT check Drive sound heard
Turn the referenced motor ON with OUTPUT check Drive sound not heard
Solution:
• Reconnect the connector.
• Replace the motor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.:Bypass Length Sensor / SP5-803-024 (By-pass: Sub Scan Length Sensor)
Cause verification Problem Judgement
1: Paper detected Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
0: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Checking paper jam, or paper status
Check the paper position (Check whether or not the leading edge of the paper, side paper guide, and end paper guide are positioned according to the manual.)
Check if the paper has reached the maximum stackable limit of the side paper guide.
• Check the paper orientation.
• Turn the paper in the feed tray upside down.
Reduce the paper to below the stackable limit.
1021
6. Troubleshooting
1022
Check if extra thin paper or thick paper exceeding the supported paper thickness is being used.
Use a supported paper type.
Check if the paper thickness and size are detected correctly. Set the paper thickness and size to the correct value.
Check if the paper being used produces a lot of paper dust.
Change the paper type (if possible).
Check if there is no double feeding.
Check if the paper feed tray is not stained with a lot of paper dust.
Fan the paper.
Clean the paper feed tray.
Check if the paper roller is not stained with paper dust.
Clean the pick-up roller, feed roller, and friction roller for 1st feed tray.
Target Part/SP No.:Transport Sensor (2nd Feed Tray) / SP5-803-005 (Transport Sensor 2)
Cause verification Problem Judgement
0 :Paper detected Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.: Paper Feed Motor / SP5-804-016 (Feed Motor:CW:Standard Speed)
Cause Verification Problem Judgement
Turn the referenced motor OFF with OUTPUT check Drive sound heard
Turn the referenced motor ON with OUTPUT check Drive sound not heard
Solution:
Troubleshooting for Transport/Paper Feeding of the Machine
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.: Transport Motor / SP5-804-028
Cause verification
Turn the referenced motor OFF with OUTPUT check
Turn the referenced motor ON with OUTPUT check
Problem Judgement
Drive sound heard
Drive sound not heard
Solution:
• Reconnect the connector.
• Replace the motor.
• Replace the Paper Transport IOB.
• Replace the harness.
Checking paper jam, or paper status
Check the paper position (Check whether or not the leading edge of the paper, side paper guide, and end paper guide are positioned according to the manual.)
Check if the paper has reached the maximum stackable limit of the side paper guide.
Check if extra thin paper or thick paper exceeding the supported paper thickness is being used.
• Check the paper orientation.
• Turn the paper in the feed tray upside down.
Reduce the paper to below the stackable limit.
Use a supported paper type.
Check if the paper thickness and size are detected correctly. Set the paper thickness and size to the correct value.
Check if the paper being used produces a lot of paper dust.
Change the paper type (if possible).
Check if there is no double feeding.
Check if the paper feed tray is not stained with a lot of paper dust.
Fan the paper.
Clean the paper feed tray.
Check if the paper roller is not stained with paper dust.
Clean the pick-up roller, feed roller, and friction roller for 2nd feed tray.
1023
6. Troubleshooting
1024
Target Part/SP No.:Registration Sensor / SP5-803-001
Cause verification
Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
Problem Judgement
0 :Paper detected
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.: Bypass/Duplex Motor / SP5-804-071 (Duplex Bypass
Motor:CW:Standard Speed)
Cause verification Problem Judgement
Turn the referenced motor OFF with OUTPUT check
Turn the referenced motor ON with OUTPUT check
Drive sound heard
Drive sound not heard
Solution:
• Reconnect the connector.
• Replace the motor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.:Reverse Motor / SP5-804-047 (Inverter Motor:CW:Standard Speed)
Cause verification Problem Judgement
Turn the referenced motor OFF with OUTPUT check
Turn the referenced motor ON with OUTPUT check
Drive sound heard
Drive sound not heard
Solution:
• Reconnect the connector.
Troubleshooting for Transport/Paper Feeding of the Machine
• Replace the motor.
• Replace the Paper Transport IOB.
• Replace the harness.
Checking paper jam, or paper status
Check if there is no double feeding.
Fan the paper.
Target Part/SP No.: Paper Exit Sensor / SP5-803-008
Cause verification
Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
Problem Judgement
0 :Paper detected
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Checking paper jam, or paper status
Check if the leading edge of the paper and the paper feed guide are wet.
Check if there is no double feeding.
Check if the paper is curled too much.
Check if extra thin paper or thick paper exceeding the supported paper thickness is being used.
If condensation has occurred inside the machine, leave the machine idle for a few minutes to remove condensation.
Fan the paper.
If the paper is curled too much, switch on the anti-condensation heater for paper tray.
Use a supported paper type.
1025
6. Troubleshooting
1026
Check if the paper thickness and size are detected correctly.
Set the paper thickness and size to the correct value.
Target Part/SP No.:Reverse Sensor / SP5-803-009 (Inverter Sensor)
Cause verification Problem Judgement
Execute an INPUT check when there is no paper at the position of the referenced sensor.
0 :Paper detected
Execute an INPUT check when there is paper at the position of the referenced sensor.
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.: Reverse Motor / SP5-804-047 (Inverter Motor:CW:Standard Speed)
Cause verification Problem Judgement
Turn the referenced motor OFF with OUTPUT check
Turn the referenced motor ON with OUTPUT check
Drive sound heard
Drive sound not heard
Solution:
• Reconnect the connector.
• Replace the motor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.:Paper Exit Solenoid / SP5-804-004 (Exit Junction Solenoid)
Cause verification Problem Judgement
Turn the referenced solenoid OFF with OUTPUT check
Turn the referenced solenoid ON with OUTPUT check
Drive sound heard
Drive sound not heard
Troubleshooting for Transport/Paper Feeding of the Machine
Solution:
• Reconnect the connector.
• Replace the solenoid.
• Replace the Paper Transport IOB.
• Replace the harness.
Checking paper jam, or paper status
Check if the leading edge of the paper and the paper feed guide are wet.
Check if there is no double feeding.
Check if the paper is curled too much.
Check if extra thin paper or thick paper exceeding the supported paper thickness is being used.
Check if the paper thickness and size are detected correctly.
If condensation has occurred inside the machine, leave the machine idle for a few minutes to remove condensation.
Fan the paper.
If the paper is curled too much, switch on the anti-condensation heater for paper tray.
Use a supported paper type.
Set the paper thickness and size to the correct value.
Target Part/SP No.:Reverse Sensor / SP5-803-009 (Inverter Sensor)
Cause verification Problem Judgement
0 :Paper detected Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
1027
1028
6. Troubleshooting
Target Part/SP No.:Duplex Entrance Motor / SP5-804-065 (Duplex Entrance
Motor:CW:Standard Speed)
Cause verification Problem Judgement
Turn the referenced motor OFF with OUTPUT check
Turn the referenced motor ON with OUTPUT check
Drive sound heard
Drive sound not heard
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Checking paper jam, or paper status
Check if the leading edge of the paper and the paper feed guide are wet.
Check if there is no double feeding.
Check if the paper is curled too much.
If condensation has occurred inside the machine, leave the machine idle for a few minutes to remove condensation.
Fan the paper.
If the paper is curled too much, switch on the anti-condensation heater for paper tray.
Use a supported paper type.
Check if extra thin paper or thick paper exceeding the supported paper thickness is being used.
Check if the paper thickness and size are detected correctly.
Set the paper thickness and size to the correct value.
Target Part/SP No.:Duplex Exit Sensor / SP5-803-010
Cause verification
Execute an INPUT check when there is no paper at the position of the referenced sensor.
Problem Judgement
0 :Paper detected
Troubleshooting for Transport/Paper Feeding of the Machine
Cause verification
Execute an INPUT check when there is paper at the position of the referenced sensor.
Problem Judgement
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.: Bypass/Duplex Motor / SP5-804-071 (Duplex Bypass
Motor:CW:Standard Speed)
Cause verification Problem Judgement
Turn the referenced motor OFF with OUTPUT check Drive sound heard
Turn the referenced motor ON with OUTPUT check Drive sound not heard
Solution:
• Reconnect the connector.
• Replace the motor.
• Replace the Paper Transport IOB.
• Replace the harness.
Checking paper jam, or paper status
Check if there is no double feeding.
Check if the paper is curled too much.
Fan the paper.
If the paper is curled too much, switch on the anti-condensation heater for paper tray.
Use a supported paper type.
Check if extra thin paper or thick paper exceeding the supported paper thickness is being used.
Check if the paper thickness and size are detected correctly.
Set the paper thickness and size to the correct value.
1029
1030
6. Troubleshooting
Target Part/SP No.:Duplex Exit Sensor / SP5-803-010
Cause verification
Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
Problem Judgement
0 :Paper detected
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Checking paper jam, or paper status
Check if there is no double feeding.
Check if the paper is curled too much.
Fan the paper.
If the paper is curled too much, switch on the anti-condensation heater for paper tray.
Use a supported paper type.
Check if extra thin paper or thick paper exceeding the supported paper thickness is being used.
Check if the paper thickness and size are detected correctly.
Set the paper thickness and size to the correct value.
Target Part/SP No.:Duplex Entrance Sensor / SP5-803-011
Cause verification
Execute an INPUT check when there is no paper at the position of the referenced sensor.
Problem Judgement
0 :Paper detected
Execute an INPUT check when there is paper at the position of the referenced sensor.
1: Paper not detected
Troubleshooting for Transport/Paper Feeding of the Machine
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.:Duplex Entrance Motor / SP5-804-065 (Duplex Entrance
Motor:CW:Standard Speed)
Cause verification Problem Judgement
Turn the referenced motor OFF with OUTPUT check
Turn the referenced motor ON with OUTPUT check
Drive sound heard
Drive sound not heard
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.:Paper Exit Solenoid / SP5-804-004 (Exit Junction Solenoid)
Cause verification Problem Judgement
Turn the referenced solenoid OFF with OUTPUT check
Turn the referenced solenoid ON with OUTPUT check
Drive sound heard
Drive sound not heard
Solution:
• Reconnect the connector.
• Replace the solenoid.
• Replace the Paper Transport IOB.
• Replace the harness.
Checking paper jam, or paper status
Check if there is no double feeding.
Fan the paper.
1031
1032
6. Troubleshooting
Check if the paper is curled too much.
If the paper is curled too much, switch on the anti-condensation heater for paper tray.
Use a supported paper type.
Check if extra thin paper or thick paper exceeding the supported paper thickness is being used.
Check if the paper thickness and size are detected correctly.
Set the paper thickness and size to the correct value.
Target Part/SP No.:Duplex Entrance Sensor / SP5-803-011
Cause verification
Execute an INPUT check when there is no paper at the position of the referenced sensor.
Problem Judgement
0 :Paper detected
Execute an INPUT check when there is paper at the position of the referenced sensor.
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.:Duplex Entrance Motor/ SP5-804-065 (Duplex Entrance
Motor:CW:Standard Speed)
Cause verification Problem Judgement
Turn the referenced motor OFF with OUTPUT check Drive sound heard
Turn the referenced motor ON with OUTPUT check Drive sound not heard
Solution:
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
Troubleshooting for Transport/Paper Feeding of the Machine
• Replace the harness.
Target Part/SP No.:Duplex/ Bypass Motor / SP5-804-071 (Duplex Bypass
Motor:CW:Standard Speed)
Cause verification Problem Judgement
Turn the referenced motor OFF with OUTPUT check Drive sound heard
Turn the referenced motor ON with OUTPUT check Drive sound not heard
Solution:
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Checking paper jam, or paper status
Check if there is no double feeding.
Check if the paper is curled too much.
Fan the paper.
If the paper is curled too much, switch on the anti-condensation heater for paper tray.
Use a supported paper type.
Check if extra thin paper or thick paper exceeding the supported paper thickness is being used.
Check if the paper thickness and size are detected correctly.
Set the paper thickness and size to the correct value.
Target Part/SP No.:Registration Sensor / SP5-803-001 (Registration Sensor)
Cause verification Problem Judgement
Execute an INPUT check when there is no paper at the position of the referenced sensor.
0 :Paper detected
Execute an INPUT check when there is paper at the position of the referenced sensor.
1: Paper not detected
Solution:
• Clean the sensor.
1033
1034
6. Troubleshooting
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Checking paper jam, or paper status
Check if there is no double feeding.
Check if the paper is curled too much.
Fan the paper.
If the paper is curled too much, switch on the anti-condensation heater for the paper tray.
Use a supported paper type.
Check if extra thin paper or thick paper exceeding the supported paper thickness is being used.
Check if the paper thickness and size are detected correctly.
Set the paper thickness and size to the correct value.
Target Part/SP No.:Transport Sensor (1st Feed Tray) / SP5-803-003 (Transport Sensor 1)
Cause verification Problem Judgement
0 :Paper detected Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
1: Paper not detected
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.: Transport Motor / SP5-804-028 (Bypass V-Transport Motor: CW: Std
Speed)
Cause verification Problem Judgement
Turn the referenced motor OFF with OUTPUT check Drive sound heard
Troubleshooting for Transport/Paper Feeding of the Machine
Cause verification
Turn the referenced motor ON with OUTPUT check
Solution:
• Reconnect the connector.
• Replace the motor.
• Replace the Paper Transport IOB.
• Replace the harness.
Problem Judgement
Drive sound not heard
Target Part/SP No.:Paper End Sensor (1st Feed Tray) / SP5-803-015 (Tray 1: Paper End
Detection)
Cause verification Problem Judgement
1: Paper detected Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
0: Paper not detected
Solution:
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Feeler for 1st paper end sensor
Cause verification
Check if the feeler for 1st paper end sensor is unfastened.
Solution:
• Reinstall the feeler.
• Check if there are any defects in the 1st paper feed unit.
Problem Judgement
Feeler is unfastened.
1035
1036
6. Troubleshooting
Target Part/SP No.:Paper End Sensor (2nd Feed Tray) / SP5-803-019 (Tray 2: Paper End
Detection)
Cause verification Problem Judgement
1: Paper detected Execute an INPUT check when there is no paper at the position of the referenced sensor.
Execute an INPUT check when there is paper at the position of the referenced sensor.
0: Paper not detected
Solution:
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Feeler for 2nd paper end sensor
Cause verification
Check if the feeler for 2nd paper end sensor is unfastened.
Solution:
• Reinstall the feeler.
• Check if there are any defects in the 2nd paper feed unit.
Problem Judgement
Feeler is unfastened.
Target Part/SP No.:Tray Set Switch (1st Feed Tray) / SP5-803-016 (Tray 1: Set Sensor)
Cause verification Problem Judgement
1: Not set Manually press the referenced switch (Done after detaching paper feeding tray 1 from the machine.)
Pull out paper feed tray 1 from the machine.
0: Set
Solution:
• Reconnect the connector.
• Replace the sensor.
Troubleshooting for Transport/Paper Feeding of the Machine
• Replace the Paper Transport IOB.
• Replace the harness.
1st Paper Feed Tray
Replace the 1st paper feed tray.
Replace the 1st paper feed tray.
Target Part/SP No.:Tray Set Switch (2nd Feed Tray) / SP5-803-020 (Tray 2: Set Sensor)
Cause verification Problem Judgement
1: Not set Manually press the referenced switch (Done after detaching paper feeding tray 2 from the machine.)
Pull out paper feed tray 2 from the machine.
0: Set
Solution:
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
2nd Paper Feed Tray
Check the 2nd tray set sensor to see if there are any defects.
Replace the 2nd paper feed tray.
Target Part/SP No.:Size Switch (2nd Feed Tray) / SP5-803-021 (Tray 2: Size Sensor)
Cause verification Problem Judgement
Parameter other than 00000111 Press the 1st switch from the right on the size switch of paper feed tray 2 when seen from the front of the machine (Done after detaching paper feed tray 2)
Press the 2nd switch from the right on the size switch of paper feed tray 2 when seen from the front of the machine (Done after detaching paper feed tray 2)
Parameter other than 00001011
1037
1038
6. Troubleshooting
Cause verification
Press the 3rd switch from the right on the size switch of paper feed tray 2 when seen from the front of the machine (Done after detaching paper feed tray 2)
Press the 4th switch from the right on the size switch of paper feed tray 2 when seen from the front of the machine (Done after detaching paper feed tray 2)
Pull out paper feed tray 2 from the machine.
Solution:
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
2nd Paper Feed Tray
Check the 2nd tray set sensor to see if there are any defects.
Problem Judgement
Parameter other than 00001101
Parameter other than 00001110
Parameter other than 00001111
Replace the switch for the pick-up arm.
Target Part/SP No.:Right Door Open/Close Switch / SP5-803-026 (Right Door Open/Close
Sensor)
Cause verification Problem Judgement
1: Open Manually press the referenced switch (Done after opening the right door)
Open the right door 0: Close
Solution:
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Troubleshooting for Transport/Paper Feeding of the Machine
Target Part/SP No.:Duplex Unit Open/Close Sensor / SP5-803-027 (Tray Full Exit Sensor)
Cause verification Problem Judgement
1: Open Manually press the referenced switch (Done after opening the duplex guide plate)
Open the duplex guide plate.
0: Close
Solution:
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Pick-up Arm
Check the switch for the pick-up arm to see if there are any defects.
Replace the 2nd paper feed tray.
If the error occurs periodically, do the following steps. If the result is as shown in the "Problem
Judgement" column, follow the solutions.
Target Part/SP No.: Waste Toner Bottle Full Sensor / SP5-803-032 (Toner Collection Full
Sensor)
Cause verification Problem Judgement
Execute an INPUT check with no feeler in the sensor detection range
(Done after detaching the waste toner bottle)
1: Full
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Imaging IOB.
• Replace the harness.
1039
1040
6. Troubleshooting
Target Part/SP No.: Waste Toner Bottle Full Sensor / SP5-803-032 (Toner Collection Full
Sensor)
Cause verification Problem Judgement
Execute an INPUT check with feeler within the sensor detection range (Done after removing the waste toner bottle)
0: Not full
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Imaging IOB.
• Replace the harness.
Target Part/SP No.:Waste Toner Bottle Set Sensor / SP5-803-033 (Toner Collection Bottle Set
Sensor)
Cause verification Problem Judgement
Execute an INPUT check with the feeler within the sensor detection range
(Done after removing the waste toner bottle)
1: Not set
Solution:
• Reconnect the connector.
• Replace the sensor.
• Replace the Imaging IOB.
• Replace the harness.
Troubleshooting for Transport/Paper Feeding of the Machine
Target Part/SP No.:Waste Toner Bottle Set Sensor / SP5-803-033 (Toner Collection Bottle Set
Sensor)
Cause verification Problem Judgement
Detach the waste toner bottle from the machine.
0: Set
Solution:
• Reconnect the connector.
• Replace the sensor.
• Replace the Imaging IOB.
• Replace the harness.
Target Part/SP No.:PTR Open/Close Sensor / SP5-803-028 (PTR Open/Close Sensor)
Cause verification Problem Judgement
1: Close Execute an INPUT check with an object (e.g. paper) placed within the sensor detection range.
Execute an INPUT check without an object (e.g. paper) placed within the sensor detection range.
0: Open
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.:Paper Transfer Unit Open/Close LED / SP5-804-206 (PTR Open/Close
LED)
Cause verification Problem Judgement
Turn ON the paper transfer unit open/close LED with OUTPUT check 1: Close
1041
6. Troubleshooting
1042
Cause verification
Execute an OUTPUT check without an object (e.g. paper) placed within the sensor detection range.
Problem Judgement
0: Open
Solution:
• Clean the LED.
• Reconnect the connector.
• Replace the LED.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.:PTR Open/Close Sensor / SP5-803-028 (PTR Open/Close Sensor)
Cause verification Problem Judgement
1: Close Execute an INPUT check with an object (e.g. paper) placed within the sensor detection range
Execute an INPUT check without an object (e.g. paper) placed within the sensor detection range
0: Open
Solution:
• Clean the sensor.
• Reconnect the connector.
• Replace the sensor.
• Replace the Paper Transport IOB.
• Replace the harness.
Target Part/SP No.:Paper Transfer Unit Open/Close LED / SP5-804-206 (PTR Open/Close
LED)
Cause verification Problem Judgement
Turn OFF the paper transfer unit open/close LED with OUTPUT check LED lit
Solution:
• Clean the LED.
• Reconnect the connector.
• Replace the LED.
• Replace the Paper Transport IOB.
• Replace the harness.
Troubleshooting for Transport/Paper Feeding of the Machine
1043
1044
6. Troubleshooting
Side-to-side registration can be adjusted by the docking bracket for SR3220 [A] (and the docking bracket screw [B]).
Troubleshooting for Finishing Options
1.
Eject a sheet of A4(LEF) or A3 paper to the proof tray and check for how many divisions of the scale the edge of the paper has shifted from the center.
[A]: Scale marks for DLT
[B]: Scale marks for A3
[C]: 7 scale marks in 2mm intervals
[D]: Center mark
2.
Change the position of the standard bracket by rotating it 180 degrees as shown below.
This makes the docking bracket easier to slide horizontally. Then reattach the docking bracket to the mainframe.
[A]: Reverse
If the paper shifts towards the front
Slide the docking bracket towards the front side by the amount of shift, to move the finisher in the same direction.
e.g.: When the paper has shifted by 2 mm towards the front from the center mark (2 mm/division of the scale), move the docking bracket towards the front by 2 mm (2 divisions). The divisions move towards the rear.
1045
6. Troubleshooting
[A]: Proof Tray
[B]: Docking Bracket Screw
If the paper shifts towards the rear
Slide the docking bracket towards the rear by the amount of shift, to move the finisher in the same direction.
e.g.: When the paper has shifted by 2 mm towards the rear from the center mark (2 mm/division of the scale), move the docking bracket towards the rear by 2 mm (2 divisions). The divisions move towards the front.
1046
[A]: Proof Tray
[B]: Docking Bracket Screw
• After the adjustment, check the side-to-side registration by feeding paper out to the proof tray. If the shift has not been solved, adjust the docking bracket (screw for the docking bracket) slightly again.
Troubleshooting for Finishing Options
If a paper alignment problem occurs as shown below, do the following procedure to adjust the jogger width.
Cause
Depending on the type of paper or the manufacturer, the paper may not be the correct size. In this case, the paper may not align properly even when the jogger is used.
Solution
Adjust the jogger width with SP6-143 (adjustable threshold: -1.5 to +1.5 mm for each paper size).
• SP6-143 (Jogger Pos Adj:1K FIN)
• Adjust the jogger width to be slightly narrower (approximately -0.5 mm) than the paper width.
Paper curl may occur when output gets to near full. Paste the Mylar to the full detection feeler to detect tray full early before paper curl occurs.
1047
1048
6. Troubleshooting
1.
Pull the finisher [A]
2.
Remove the finisher front cover [A] ( x2)
3.
Remove the left lower cover [A] ( x2)
Troubleshooting for Finishing Options
4.
Rotate the gear [A] to lift down the movable tray [B].
1049
6. Troubleshooting
5.
Remove the paper exit tray [A] ( x2)
6.
Paste the Mylar [A] on the full detection feeler [B].
1050
7.
Re-attach the paper exit tray ( x2)
Troubleshooting for Finishing Options
8.
Move the movable tray [A] up and down to check that the Mylar does go through the sensor properly.
9.
Re-attach the left lower cover ( x2)
10.
Re-attach the finisher front cover ( x2)
When using the mixed mode, duplex (curls towards the lower side) over the simplex (curl towards the upper side) and paper curl occurs, attach the auxiliary tray (D7667010), disable the paper exit full sensor, and paste the Mylar.
1051
1052
6. Troubleshooting
1.
Remove the paper exit cover [A] ( ×2)
2.
Release the clamp and disconnect the harness of the paper exit full sensor 1 [A].
3.
Loop and clamp the harness [A] as shown.
Troubleshooting for Finishing Options
4.
Release the clamp and disconnect the harness of the paper exit full sensor 2 (Staple) [A].
5.
Loop and clamp the harness [A] as shown.
• If the harness cable [A] is short to loop, clamp the harness without looping.
6.
Re-attach the paper exit cover ( ×2)
1053
6. Troubleshooting
7.
Attach the auxiliary tray (D7667010) [B] to the paper exit tray [A]
8.
Paste the Mylars [A] on the frame of the finisher.
1054
Model
Booklet Finisher SR3220
Internal Finisher SR3130
50 sheets
Corner Staple
50 sheets -
15 sheets
Booklet Staple
Troubleshooting for Finishing Options
When corner stapling
Sheets are fed out without being stapled. First, the maximum number of sheets (50) is stacked in the staple tray and fed out. Following this, any remaining sheets that exceed this maximum are also stacked and fed out without being stapled, in the same way.
Example:
If 60 sheets are set to be stapled, the first 50 are stacked in the staple tray and then fed out without being stapled. The remaining 10 are then stacked in the tray and fed out without being stapled.
When the maximum number of originals for a stapled set has been scanned, "Stapling capacity exceeded" is displayed on the LCD.
There is no message displayed prompting the user to cancel or continue with the 51st original.
When booklet stapling
The following dialog is displayed when the maximum number of sheets in a stapled set is reached during the scanning of the originals. The user is prompted before printing begins.
1055
6. Troubleshooting
1056
[Stop] The job is canceled (no further scanning, no printing)
[Continue] Sets are stapled at maximum capacity in batch and fed out.
Example:
The machine stops scanning after 20 out of 30 originals are scanned.
The message shown above is displayed.
If [Continue] is selected, printing starts and sheets are stapled in batches of 20 sheets and 10 sheets.
SP5-199 sets whether to staple sheets stacked in the staple tray or finisher before feeding out.
0 (default): Behavior depends on the finisher attached.
1: Sheets are fed out without being stapled.
2: Sheets are stapled and fed out.
Electrical Component Defects
Name
FU105 None
FU1
Output connector
FU101
CN985 (Fusing center lamp)
CN986 (Fusing edge lamp)
FU102 CN988 (DC power supply)
FU110
CN921(Heater for Tray1, 2, and optional trays)
CN922 (Heater for Scanner and PCU)
CN911(IOB)
Capacity Part number
Voltage
15A (NA)
8A
AC
15A(NA)
8A
AC
2A
Part name
11071241(NA)
11071366
TLC-15A-N4
(NA)
FIH 250V
8A(EM)8A
11071241(NA)
11071366
TLC-15A-N4
(NA)
FIH 250V
8A(EM)8A
11071225
AC
2A
AC
5A
5V
SLT 250V 2A
11071362
SCT2A
11071229
SLT 250V 5A
Market exchange possible
Remarks
Yes
Installed on AC control board
Yes
Installed on AC control board
NO
Installed on Heater
Board (Service Part)
NO
Installed on AC control board
NO
Installed on DC power supply
1057
1058
6. Troubleshooting
Name
FU2
FU3
Output connector
CN911(IPU)
CN912(IOB)
FU4
CN917 (Interlock switch
[IOB])
FU5
CN917 (Interlock switch
[IOB])
FU7
CN913(FIN)
CN914(BANK)
Fuse position
Capacity
Voltage
5A
5V
8A
24V
8A
24V
8A
24V
8A
24V
Part number
Part name
11071229
SLT 250V 5A
51MS(P)080L
51MS(P)080L
51MS(P)080L
51MS(P)080L
Market exchange possible
Remarks
NO
Installed on DC power supply
NO
Installed on DC power supply
NO
Installed on DC power supply
NO
Installed on DC power supply
NO
Installed on DC power supply
Electrical Component Defects
1059
1060
6. Troubleshooting
Marks on prints and copies are mostly due to dirt on the DF exposure glass [A], generally caused by adhesive contaminants (such as ball point pen ink and correction fluid).
Compared to non-adhesive contaminants (such as paper fragments and eraser dust), adhesive contaminants are more likely to lead to complaints from customers because of the following:
• Vertical streaks caused by adhesive contaminants are more visible in terms of image quality.
• Unless removed by cleaning, adhesive contaminants continue to produce vertical streaks, while non-adhesive contaminants stop producing streaks after they are dislodged.
• Many adhesive contaminants are difficult to remove by cleaning.
The ARDF DF3090 / SPDF DF3100 features a system (non-contact scanning) to reduce vertical streaks caused by adhesive contaminants.
Vertical Streaks on Copies due to Scanning Problems
Contact scanning:
Other ADFs/ARDFs
In contact scanning, the whole of the original comes into contact with the DF exposure glass
[A] so that non-adhesive contaminants can be removed.
Non-contact scanning:
DF3090 / DF3100
By means of the Mylar sheet [B], originals are kept slightly above the DF exposure glass [A], preventing adhesive contaminants from adhering to the glass.
The ARDF DF3090 / SPDF DF3100 can be converted from non-contact scanning to contact scanning for users who wish to reduce vertical streaks caused by non-adhesive contaminants.
SP No.
SP4-688-001 (for ARDF3090)
SP4-688-002 (for SPDF3100)
SP4-871-003 (both ARDF and SPDF)
Contact scanning
103%
96%
0.00%
Non-contact scanning
106%
101%
0.11%
1.
Unplug the machine power cord before starting the following procedure.
2.
Remove the ARDF front cover [A] ( x1).
1061
1062
6. Troubleshooting
3.
Remove the Scanning guide plate [B] ( [A]x1).
4.
Remove the plastic guides [A] on the sides of the scanning guide plate( x1).
5.
Attach the guides for contact scanning. Each guide has a hole [B].
Vertical Streaks on Copies due to Scanning Problems
6.
Mount the scanning guide plate, taking care not to damage the sheet [A].
7.
Peel off the gap sheet [A] from the DF exposure glass with your hands.
8.
Clean the DF exposure glass [A] with alcohol.
To avoid paper jams, make sure adhesive is completely removed.
1063
1064
6. Troubleshooting
9.
Turn the main switch on.
10.
Start the SP mode.
11.
Select SP4-688-001 (DF Density Adjustment ARDF) and change the setting from "106" to
"103" for the contact scanning.
12.
Change the DF magnification (SP4-871-003) from [0.11%] to [0.00%].
• When returning the setting back to non-contact scanning, return the SP values also.
1.
Open the SPDF and exchange the entrance lower guide unit [A] to a non-contact type part.
• Entrance lower guide unit for non-contact transport: The following areas are black [A].
• Entrance lower guide unit for contact transport: The following areas are clear and colorless
[B].
Vertical Streaks on Copies due to Scanning Problems
2.
Exchange the scanning guide plate [A] to a non-contact type part (hook x 1).
• [A] : The color of the marker of the non-contact type scanning guide plate for this machine is gray.
• [B]: The color of the marker of the contact type scanning guide plate for this machine is white.
• [C]: The color of the marker of the non-contact type scanning guide plate for previous machine is black.
3.
Attach the scanning guide plate for contact transport [A] (hook x 1).
1065
6. Troubleshooting
4.
Attach the entrance lower guide unit for contact transport [B] ( x 2).
1066
5.
Peel off the gap sheet [A] from the DF exposure glass with your hands.
6.
Clean the DF exposure glass [A] with alcohol.
To avoid paper jams, make sure adhesive is completely removed.
Vertical Streaks on Copies due to Scanning Problems
7.
Enter the SP mode.
8.
Change SP4-688-002 (Scan Image Density Adjustment 1-pass) from "101" to "96".
9.
Change the DF magnification (SP4-871-003) from [0.11%] to [0.00%].
• When returning the setting back to non-contact scanning, return the SP values also.
1067
6. Troubleshooting
In the Auto Color Selection (hereafter called ACS) mode, if copying or scanning an original on which color is printed only on the edge, the original will be misjudged as monochrome. If so, color is not printed on the output.
Copy Application
The misjudgment occurs when copying an original which has color at the edge, and that color is printed on the output 10 mm from the edge in the ACS mode.
When using the copy application, if the original is judged as monochrome, color on the document may not be printed on the output. When printing the standard 10 colors used in Microsoft Office
Word 2013 (an example is shown below), the following colors with the "x" mark will disappear if the document is judged as monochrome in the ACS mode.
• Colors with the "x" mark will not be printed if the document is judged as monochrome. The result may differ depending on the equipment status or environment.
1068
Scanner Application
The misjudgment occurs when scanning an original which has color only 15 mm from the edge
(using the original as a standard) in the ACS mode.
In the ACS mode, the edge of the original is excluded from the judgment. Only the center part of the original document is the target area to judge color or monochrome (in order to prevent misjudgment due to noise).
When copying in the ACS mode, ACS judgment and the image processing equivalent to full color is performed simultaneously. If judged as monochrome in the ACS judgment, color without a K component will not be printed.
Image Quality Problems
Change the ACS area excluded from judgment with the following SP settings.
The smaller the value, the smaller the ACS area excluded from judgment becomes, which enables the document to be judged as color.
SP No.
4-938-001
4-938-002
4-938-003
4-938-004
4-938-005
4-938-006
4-938-007
4-938-008
SP Name
ACS:Edge Mask Copy:Sub LEdge
ACS:Edge Mask Copy:Sub TEdge
ACS:Edge Mask Copy:Main LEdge
ACS:Edge Mask Copy:Main TEdge
ACS:Edge Mask Scan:Sub LEdge
ACS:Edge Mask Scan:Sub TEdge
ACS:Edge Mask Scan:Main LEdge
ACS:Edge Mask Scan:Main TEdge
10
15
15
15
15
Def.
10
10
10
0
0
0
0
0
Max.
0
0
0
31
31
31
31
31
Min.
31
31
31
1069
1070
6. Troubleshooting
[A]: Sub scan direction: leading edge (left)
[B]: Main scan direction (front)
[C]: Sub scan direction: leading edge (right)
[D]: Main scan direction (rear)
[E]: Paper
[F]: ACS area excluded from judgment
• Because the edge of the original is subject to noise, color misjudgment may occur after setting these
SPs smaller than the defaults. In this case, in order to avoid complaints concerning extra cost, be sure to ask the customer for permission before changing these SP settings.
Causes
The strong blue component of the paper causes the difference in RGB values to be relatively large.
As a result, ACS mistakenly judges that the paper is blue.
• ACS makes this judgment based on the RGB thresholds set in SP mode.
Solutions
Change the setting of SP4-939-001 (ACS:Color Range) until ACS works correctly.
• Change the value of the SP to “-1” or “-2” when a black and white document is misjudged as a color document.
Image Quality Problems
1071
1072
6. Troubleshooting
Interval
31.4mm
34.6mm
37.7mm
48.7mm
54.8mm
94.2mm
94.2mm
100.5mm
963.8mm
Target part
Charge roller cleaner
Development roller
Charge roller
Paper transfer roller
Image transfer drive roller
Drum
Fusing sleeve belt
Pressure roller
Image transfer belt
Replacement part
PCU
Development unit
PCU
Paper transfer roller unit
Image transfer unit
PCU
Fusing sleeve belt unit/ Fusing unit
Pressure roller/ Fusing unit
Image transfer belt/ Image transfer unit
Other Troubleshooting
Problem
Under the usage environment of this machine, at the placement location, fluorescent and/or LED lamps flicker.
Causes
As a result of the voltage drop occurs, when the fusing lamp is applied an electrical current. It depends on the electrical power environment, at the customer's placement location.
Solutions
The procedure varies by the flicker occurrence timing. So check the occurrence timing, and do the procedure that matches the timing.
Occurrence Timing
Timing
Recovery from energy saving
Solutions
Set SP1-135-001 (Inrush
Control) to "1 (ON)".
Side effect
Recovery time from energy saving becomes slower approx. 0.4 sec..
1073
1074
6. Troubleshooting
Timing
After the recovery from energy saving
Printing
Solutions
Set SP1-135-001 (Inrush
Control) to "1 (ON)".
Set SP1-135-002 (Flicker
Control) to "1 (ON)".
• The fusing temperature drops during the operation. After copying starts, the fusing temperature is raised up to a printable temperature. Because of that, copying completion time becomes slower (approx. 1-2 sec.).
Side effect
• Recovery time from energy saving becomes slower approx. 0.4 sec..
• In the case of the adhesion amount of an image is large, an offset may occur.
• In the case of a fusing offset occurs, in the related SP to fusing offsets, setting values must be changed.
If it has not been improved in the above, do the following procedures in addition;
• Stop the lighting of the fusing lamp after the warmup. Set SP1-121-001
(Switch:Rotation Start/
Stop:Time:After Reload) to
"0 sec".
Set SP1-135-002 (Flicker
Control) to "1 (ON)".
• In the case of the adhesion amount of an image is large, an offset may occur.
• In the case of a fusing offset occurs, in the related SP to fusing offsets, setting values must be changed.
Other Troubleshooting
Related SP to Fusing Offsets
SP Name
Print Target Temp.:Plain1:FC:Center
Print Target Temp.:Plain1:BW:Center
Print Target Temp.:Plain2:FC:Center
Print Target Temp.:Plain2:BW:Center
Print Target Temp.: Thin:FC:Center
Print Target Temp.: Thin:BW:Center
Print Target Temp.: M-thick:FC:Center
Print Target Temp.: M-thick:BW:Center
SP No.
SP1-105-001
SP1-105-003
SP1-105-005
SP1-105-007
SP1-105-009
SP1-105-011
SP1-105-013
SP1-105-015
Value
As initial values + 10 °C are the upper limits, change values to improve offsets.
1075
1076
6. Troubleshooting
Items
Scanner type
Scanner carriage storage upon shipping
Main scanning magnification adjustment
-
MP C2003/C2503
/C2011
None
MP C6004/C5504/C4504
/C3504/C3004
MP C2004/C2504
Short focus scanner
For distortion correction: After replacing the scanner carriage, the correction value specified on the supplied sheet in the SP code must be entered. For
details, see page 436 "Scanner Carriage".
The scanner carriage must be moved to the lock position to lock the carriage to the scanner frame before shipping.
Not available
Magnification adjustment is available for the main scanning direction with SP4-871-003, -004.
SIO
Items
MP C2003/C2503
/C2011
Available
MP C6004/C5504/C4504
/C3504/C3004
MP C2004/C2504
Not available
The functions of this old board are built into the IPU.
Copy data security function
Available by option Available by default on the IPU
1077
1078
7. Detailed Descriptions
Items
MUSIC
MP C2003/C2503
/C2011
Executing rough adjustment -> fine adjustment only
MP C6004/C5504/C4504
/C3504/C3004
MP C2004/C2504
Process upon execution of SP2-111-004 (Forced Line
Position Adj.: mode d) and [Color Registration] in the
User Tools have been changed.
• Normal Operation: rough adjustment -> fine adjustment -> contact MUSIC (new process)
• With Imageable Area Extension Unit: rough adjustment -> fine adjustment
Items
Laser unit
MP C2003/C2503
/C2011
LD 1 beam
MP C6004/C5504/C4504
/C3504/C3004
MPC4504/C5504/C6004:
LD 4 beams
MP C3004/C3504:
LD 1 beam
MP C2004/C2504
LD 1 beam
Items
Removal of PCDU seal
MP C2003/C2503
/C2011
MP C6004/C5504/C4504
/C3504/C3004
MP C2004/C2504
The seals must be pulled out for all colors.
MPC4504/C5504/C6004:
The seals for all colors must be wound up.
MP C3004/C3504:
The seal for K must be wound up with a special tool, and the seals for CMY must be pulled out
The seals must be pulled out for all colors.
Guidance for Those Who are Familiar with Predecessor Products
PCU
Items
Development unit
MP C2003/C2503
/C2011
DC charge roller
(Contact type)
Correction SP value must be input when
PCU is replaced
No lubricant bar
Discharge lamp is in the main frame
Two mixing coils, twoway circulation
MP C6004/C5504/C4504
/C3504/C3004
MP C2004/C2504
AC charge roller (No contact type)
Lubricant bar
No discharge lamp
DC charge roller
(Contact type)
Correction SP value must be input when
PCU is replaced
No lubricant bar
Discharge lamp is in the main frame
MPC4504/C5504/C6004:
OD (One-way circulation of developer) system
MP C3004/C3504:
K: OD (One-way circulation of developer) system
CMY: Two mixing coils, one way circulation
Two mixing coils, two-way circulation
Items
MP C2003/C2503
/C2011
Waste toner cover With latch
MP C6004/C5504/C4504
/C3504/C3004
Without latch
MP C2004/C2504
Items
TM/ID sensor shutter
MP C2003/C2503
/C2011
MP C6004/C5504/C4504
/C3504/C3004
MP C2004/C2504
Available Not Available
1079
1080
7. Detailed Descriptions
exit
Items
Bypass tray / Main machine jam code
Main tray paper
-
-
MP C2003/C2503
/C2011
MP C6004/C5504/C4504
/C3504/C3004
MP C2004/C2504
The following codes are used to isolate the cause:
• JAM048: Transport Sensor Lag Jam from Bypass
Tray
• JAM051: Transport Sensor Lag Jam from 1st
Feed Tray
• Improved stacking performance after feedout by adding resilience to the paper with the paper exit driven roller (drum shape).
• To prevent paper jam when the paper is delivered from the machine’s paper exit to the internal exit peripherals, attach the paper support guide (supplied with the peripherals).
• Replaced the paper exit driven roller to a flat type roller to prevent jamming when paper is fed to the internal exit peripherals.
Tray draw-in mechanism
Paper feed sensor/
Paper exit full sensor
Paper thickness
(Duplex)
Not Available
Not Available
52 - 169 g/m
2
Removing wrinkle in tray
Available
Available
52 - 256 g/m
2
Not Available
Not Available
52 - 169 g/m
Screwed with L-shaped sheet metal
Support component and decal are provided
User installable
2
RTB 28
New information
Guidance for Those Who are Familiar with Predecessor Products
Items
Curl correction
Fusing shield plate
Fusing shield plate position sensor
2
MP C2003/C2503
/C2011
Not Available
Available
MP C6004/C5504/C4504
/C3504/C3004
MP C2004/C2504
Equipped with a curl correction mechanism at the fusing exit.
MP C6004/C5504/
C4504:
Available
MP C3004/C3504:
Not Available
Not Available
MP C6004/C5504/
C4504:
-
1
MP C3004/C3504:
-
Heat conduction plate
Others -
Not Available Available
Changed the drawer connector location
• Changed the drawer connector location:
[A]: MP C6004/C5504/C4504/C3504/C2504/C2004
[B]: MP C2003/C2503/C2011
1081
7. Detailed Descriptions
1082
SIO
OPU
Items
Human detection
(Proximity sensor)
MP C2003/C2503
/C2011
Available
Not Available
MP C6004/C5504/C4504
/C3504/C3004
MP C2004/C2504
Not available
The functions for this old board are included on the
IPU
Available
Equipped with the proximity sensor (human detection sensor).
1st generation Smart
Operation Panel
2nd generation Smart Operation Panel
Guidance for Those Who are Familiar with Predecessor Products
Air flow
Duct
Items
Noise control
-
-
MP C2003/C2503
/C2011
8 fans
MP C6004/C5504/C4504
/C3504/C3004
MP C6004/C5504/
C4504:
10 fans
MP C3004/C3504:
7 fans
MP C2004/C2504
7 fans
Increased the rigidity of the duct
Changed the duct shape
• Equipped with a Helmholtz silencer
• Labyrinth structure of the exterior
• Labyrinth structure of the exterior:
• Exterior parts engage with each other to reduce the leaking of the driving noise.
1083
1084
7. Detailed Descriptions
Items
MP C2003/C2503
/C2011
MP C6004/C5504/C4504
/C3504/C3004
MP C2004/C2504
From the usual non-helical gears [A], we increased the use of helical gears [B] to increase the efficiency of engagement. This has also reduced the rattling noise due to the increased gear engagement.
Noise control -
Silencing grease for the drive parts
-
Grease is applied to over 100 parts, including gears, shafts, and bearings, to reduce the driving noise.
Changing the Default Value for the Binding Margin
Until the last model, the default value for the binding margin was “5 mm on the right (on the back of the sheet)” when copying on both sides, in order to align the prints on both sides when punching. This has occasionally caused the paper edges to appear on the printed copies.
Thus, in this series, the default value for the binding margin is changed to “0 mm on the right (on the back of the sheet)” and the default value to mask the paper edge (SP mode) is also changed to reduce the chance of the black streak appearing.
Binding Margin Setting
Guidance for Those Who are Familiar with Predecessor Products
Changed Default Values in the SP mode
SP4-012-001 (Set Scale Mask Book:Sub Ledge) 0 -> 1mm
SP4-012-003 (Set Scale Mask Book:Main:Ledge) 0 -> 1mm
SP6-006-007 (ADF Adjustment Rear Edge Erase Front) 0 -> -2.3mm
SP6-006-014 (ADF Adjustment T-Edge Erase (1-Pass): Front) -1.5 -> -3.0mm
SP6-006-015 (ADF Adjustment T-Edge Erase (1-Pass): Front) -1.5 -> -2.5mm
1085
7. Detailed Descriptions
1086
No.
1 Operation panel
Description
2
Anti-condensation heater (Scanner heater)
*1
3 Scanner HP sensor
4 ARDF/Platen cover sensor
5 Auto paper size (APS) sensor
No.
Description
6 Auto paper size (APS) sensor
7
8
9
Scanner lamp unit (LED)
Scanner motor
Sensor board unit (SBU)
* Service part
Component Layout
No.
Description
1 Laser optics positioning motor (Y)
2 Synchronizing detector board: M/Y-S
3 Laser optics positioning motor (M)
4 Laser optics positioning motor (C)
No.
Description
5 Polygon mirror motor
6 LD drive board (M/Y)
7 LD drive board (Bk/C)
8 Synchronizing detector board: Bk/C-S
1087
7. Detailed Descriptions
1088
No.
1 Temperature and humidity sensor
2 Interlock switch: right door
Description
3 ITB contact and release sensor
4 Paper transfer contact and release motor
5 TM/ID sensor (rear)
6 TM/ID sensor (center)
7 TM/ID sensor (front)
Component Layout
No.
1 PCDU (Y)
2 PCDU (M)
Description No.
3 PCDU (C)
4 PCDU (Bk)
Description
1089
7. Detailed Descriptions
1090
No.
Description
1 ID chip contact board (Y)
2 Toner bottle drive motor (Y)
3 ID chip contact board (M)
4 Toner bottle drive motor (M)
5 ID chip contact board (C)
6 Toner bottle drive motor (C)
7 ID chip contact board (Bk)
8 Toner bottle drive motor (Bk)
No.
Description
10 Toner end sensor (Y)
11 Toner supply motor (M)
12 Toner end sensor (M)
13 Toner supply motor (C)
14 Toner end sensor (C)
15 Toner end sensor (Bk)
16 Toner supply motor (Bk)
17 Waste toner bottle full sensor
No.
Description
9 Toner supply motor (Y)
No.
Description
18 Waste toner bottle set sensor
Component Layout
No.
Description
1 Tray set switch (1st feed tray)
2 Lift motor (1st feed tray)
3 Tray set switch (2nd feed tray)
4 Lift motor (2nd feed tray)
5 Registration sensor
6 Paper size switch (2nd Feed Tray)
7 Anti-condensation heater
No.
Description
8 Transport sensor (2nd Feed Tray)
9 Paper end sensor (2nd feed tray)
10 Upper limit sensor (2nd feed tray)
11 Transport sensor (1st feed tray)
12 Paper end sensor (1st feed tray)
13 Upper limit sensor (1st feed tray)
1091
7. Detailed Descriptions
1092
No.
Description
1 Duplex entrance motor
2 Right door open/close sensor
3 Duplex entrance sensor
4 Duplex guide plate open/close sensor
No.
Description
5 Bypass pick-up solenoid
6 Bypass / Duplex motor
7 Duplex exit sensor
8 Bypass paper end sensor
No.
Description
1 Bypass width sensor
2 Bypass length sensor
Component Layout
1093
7. Detailed Descriptions
1094
No.
Description
1 Pressure roller HP sensor
2 Thermopile (edge)
3 Thermopile (center)
4 Fusing exit sensor
5 Fusing lamp
6 Fusing sleeve thermostat (edge)
No.
Description
7 Fusing sleeve thermostat (center)
8 Non-contact thermistor (center)
9 Pressure roller thermistor (center)
10 Non-contact thermistor (edge)
11
Pressure roller thermistors (edge, full-bleed edge)
Component Layout
No.
1 Reverse motor
2 Reverse sensor
Description
3 Paper exit sensor
4 PTR open/close sensor
No.
Description
5 Fusing entrance sensor
6 Fusing exit sensor
7
Fusing exit drive solenoid
(installed on the main machine)
8 Paper exit solenoid
1095
7. Detailed Descriptions
1096
No.
Description
1 Paper exit cooling fan
2 Development intake fan
3 PSU cooling fan
4 Ozone exhaust fan
No.
Description
5 Imaging temperature sensor (Thermistor)
6 Toner supply cooling fan
7 Fusing exhaust fan
Component Layout
No.
1 Imaging IOB
Description
2 Development motor: CMY
3 PCU motor: CMY
4 Development Solenoid
5 Paper feed motor
No.
6 Transport motor
Description
7 PCU motor: Black / ITB drive motor
8 Registration motor
9 Fusing motor
10 Paper exit / Pressure release motor
1097
7. Detailed Descriptions
1098
No.
Description No.
1 Proximity sensor (Human detection sensor) 8 PSU (DC power)
Description
2 Interlock switch: front cover
3 HVP_TTS
4 Main power switch
5 Control board
6 HDD
9 PSU (AC controller board)
10 BCU
11 Controller box cooling fan
12 IPU
13
Proximity sensor (Human detection sensor) board
7 Paper transport IOB
Scanning
The short focus scanner is realized by implementing a lens block (SBU, CCD, and Lens) on the carriage.
After the scanner lamp unit emits the light to the document, the light goes through route shown below and reaches the CCD.
Scanner lamp unit (LED) -> Original -> 1st mirror (13) -> 2nd mirror (3) -> 3rd mirror (6) -> 2nd mirror
(3) -> 4th mirror (5) -> 5th mirror (14) -> lens -> pre-sensor lens -> CCD
No.
Description
1 Sheet-through exposure glass
2 Exposure glass
3 2nd mirror
4 Scanner lamp unit (LED)
5 4th mirror
6 3rd mirror
7 Scanner motor
8 APS sensors
*Service part
No.
Description
9 Sensor board unit (SBU)
10 CCD
11 Pre-sensor lens
12 Lens
13 1st mirror
14 5th mirror
15
Anti-condensation heater* (Scanner heater)
1099
1100
7. Detailed Descriptions
Two scan modes are available: book mode (platen mode) and ADF mode (sheet-through method).
In book mode (platen mode), the scanner scans the document from left to right.
When the ADF is used (ADF mode), the scanner is fixed in the home position on the left side, and the document is transported and read (sheet-through method).
Scanner lamp
The light source is an LED. The LED emits little heat (low power consumption), and has excellent light output rise characteristics.
CCD
The 3 line color CCD converts shade in the document to 3 color (B, G, and R) electrical signals.
The use of a 4.7 µm image CCD achieves low-cost and compactness.
Reflection plate (reflector)
The reflection plate reflects light from the scanner lamp, and collects light for the document read unit. The light which illuminates the document is adjusted to be the same on the left and right so as not to cast any shadow on the document.
White reference seal
A white reference seal for shading correction is affixed to the underside of the scale on the left of the MFP. This is read by the scanner and CCD when the power is ON. The data read are temporarily stored in a RAM, and used for correction of document image data.
The scanner is driven by the scanner motor [D] via the timing belt [C]. For each mode, reading is completed in one pass.
Position control of the scanner carriage [B] is based on the scanner HP sensor [A].
Scanning
1101
1102
7. Detailed Descriptions
Overall Flowchart
Scanning
To protect the scanner carriage, the carriage must be locked to the scanner frame before shipping. The scanner can be moved to the shipping lock position with SP4-806-001 (Scanner carriage storage operation).
If pre-shipping check is required, make sure to move the scanner carriage to the right position with
SP4-806-001 and mount the locking parts.
SC121-00 will occur when the power is turned on or scanning takes place while the carriage is locked.
In this MFP, for document size detection, two reflecting sensors are used for the sub scanning direction, and a CCD is used for the main scanning direction.
Sub scanning direction
The document size is detected by ON/OFF of the sensor. The pressure plate open/close sensor is used for document size detection timing. When the pressure plate open/close sensor has changed from "no cover" to "cover," the size is detected.
Main scanning direction
RGB color densities at 3 locations (S1, S2, S3) are detected by a CCD, and when any of the RGB densities is 12 digits or more, it is determined that a document is present.
The pressure plate open/close sensor is used for document size detection timing. When the pressure plate open/close sensor detects "no cover," the scanner lamp is moved to the right; when it detects "cover," the scanner lamp is moved to home position while lit, and during this time, the size is read.
1103
1104
7. Detailed Descriptions
Size
A5
A5
B6
B6
A3
B4
A4
A4
B5
B5
DLT SEF
10×15 SEF
USB4
LG
SEF
SEF
SEF
LEF
SEF
LEF
Document size
Direction
Dimensions
(main × sub)
SEF
SEF
SEF
LEF
SEF
LEF
297x420
257x364
210x297
297x210
182x257
257x182
148x210
210x148
128×182
182×128
11"×17"
10"×15"
10"×14"
8 1/2"×14"
Oficio SEF
Foolscap SEF
Folio
F
LT
SEF
SEF
SEF
LT
8×10
10×8
LEF
SEF
LEF
8 1/2"×13.4"
8 1/2"×13"
8 1/4"×13"
8"×13"
8 1/2"×11"
11"×8 1/2"
8"×10"
10"×8"
S1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
S2
Sensor response
S3 L1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
L2
-
-
-
-
-
-
-
-
-
-
-
-
Scanning
Executive
HLT
HLT
8kai
16kai
16kai
Document size
SEF
SEF
LEF
SEF
SEF
LEF
7 1/4"×10
1/2"
5 1/2"×8
1/2"
8 1/2"×5
1/2"
267×388
194×267
267×194
-
-
-
-
-
-
-
-
-
Sensor response
-
-
-
-
-
-
-
-
-
• The document width (main scanning direction) is detected by the sensor indicated with ‘ ’.
How to check the sensor state
• SP4-301 (Operation Check APS Sensor)
How to read the screen
(7)00000000(0)
0: no document
1: document present
When the sensor responds, bit 0 is displayed as "1."
• SP4-310 (Scan Size Detect Value)
Viewed from the control panel, labeling positions from rear to front S1-S3 in that order, the
RGB density at each position is displayed in digit units (the value just before scan is displayed).
Other
• SP4-303 (Min Size for APS)
Sets the display when non-standard (small size) size original is detected.
0: Display message "Original size unknown".
1: Operate assuming the original size is A5 LEF (HLT LEF for inches).
• SP4-305-001(8K/16K Detection)
By changing this SP, you can change between A4 size/letter size or Chinese paper size
(8×16).
0: Normal setting. (Default)
-
-
-
-
-
1105
1106
7. Detailed Descriptions
1: When detecting A4/LT size -> Assume that it is A4 when SEF, LT when LEF.
2: When detecting A4/LT size -> Assume that it is LT when SEF, A4 when LEF.
3: Change to 8K/16K settings.
A3, B4 -> 8K LEF
A4 LEF, B4 LEF, A5 LEF -> 16K LEF
A4 SEF, B4 SEF, A5 SEF -> 16K SEF
• SP5-126 (Set F-size Document)
Selects the paper size for the F-size original.
0: When detecting Foolscap -> Assume that the size is 8 1/2"x13". (Default)
1: When detecting Folio -> Assume that the size is 8 1/4"x13".
2: When detecting F -> Assume that the size is 8"/13".
• SP4-308 (Scan Size Detection)
Sets CCD original size detection and APS original size detection.
0: Disable: Not detect original size
1: Enable: Detect original size by the CCD unit
2: APS: APS sensor is used for detecting original size.
• SP4-309-004 (Scan Size Detect:Setting LED PWM Duty)
If the user specifies that the pre-scan lamp is too bright, the brightness pre-scan can be reduced by decreasing the value of SP4-309-004 (Scan Size Detect:Setting LED PWM Duty).
However, if the lamp brightness is reduced, size detection for a document with a large number of solid images will be less accurate.
• SP5-135 (LG_Oficio Change)
1: When detecting LG size -> Assume that the size is 8 1/2"x14".
2: When detecting Oficio size -> Assume that the size is 8 1/2"x13.4". (Default)
The original document does not come in contact with the sheet-through exposure glass, which prevents adhesive dirt (ball pen ink) on the document from adhering to the sheet-through exposure glass.
ADF cross-section diagram, non-contact scanning
Scanning
[A]: Sheet
[B]: Sheet-through exposure glass
[C]: Read position
[D]: Document
• Contact scanning
As the document comes in contact with the sheet-through exposure glass this is useful for dealing with adhesion of free dirt particles (paper scraps, etc.). (Self-cleaning mechanism using paper)
On the other hand, sticky dirt adhering to the document sticks to the sheet-through exposure glass, and may give rise to the appearance of black lines.
ADF cross-section diagram, contact scanning
[A]: Sheet-through exposure glass
[B]: Read position
[C]: Document
1107
7. Detailed Descriptions
If black lines due to free dirt particles appear within a short time, such as when users have documents with large amounts of paper scraps, you can change from the non-contact scanning system to the contact scanning system with the procedure in Troubleshooting - Vertical Streaks on
Copies due to Scanning Problems.
• Reference (reading position correction)
By changing SP4-020-001 (Dust Check Dust Detect:On/Off), when dirt is detected at the reading position, the reading position may be changed to avoid the dirt.
(If it cannot be avoided, an alert is displayed on the control panel advising the user to perform target glass cleaning).
Image diagram
1108
[A]: Read position
[B]: Sheet-through exposure glass
[C]: Dirt
• Dirt is detected when a document passes through, so the alert will not disappear until reading of the next document begins, even after the sheet-through exposure glass cleaning is performed.
• If dirt is detected not on the sheet-through exposure glass but on the background guide plate, the alert will not disappear even if the glass is wiped.
• The time required for the first copy is slightly (almost imperceptibly) longer.
• The detection threshold value can be changed using SP4-020-002 (Dust Check Dust
Detect:Lvl). (The larger the value is, the smaller the dirt particles that can be detected become.)
• It is prohibited to change the setting of SP4-020-003 (Dust Check Lvl Dust Reject:Lvl).
Scanning
Transport
Method
Non-contact Transport Contact Transport
Descriptions
Merit
Demerit
Aim
Note
Because of the film attached to the glass, the original doesn’t contact the glass.
It almost never causes stripes on the image that arise from foreign substances transferring from the original to the glass.
Compared with the contact method, stripes on the image caused by dust occur more often.
To improve prevention of stripes in the image caused by sticky foreign substances.
1. Be sure to replace the sheetthrough glass with the film attached on the glass.
2. When you attach the film on the glass, you need to keep the left scale attached on the glass in order to fix the location of the film.*1
3. You can change the method
(contact method to non-contact, or vice versa) by replacing some parts.*1
-
While passing, the original contacts the glass.
It almost never causes stripes on the image that arise from dust on the glass, because the glass is cleaned by contact with the transported original.
Compared with the non-contact method, stripes on the image caused by foreign substances transferred from the surface of an original to the glass occur more often.
Considering the target users of this machine, it’s important to improve prevention of stripes caused by dust in the path
*1: For details, page 1060 "Vertical Streaks on Copies due to Scanning Problems".
1109
1110
7. Detailed Descriptions
Under low temperature conditions, condensation may appear on optical parts (such as mirrors). This will cause image deletion, blacked out images, and gray images. As a countermeasure, there is an anticondensation heater [A] that is an optional service part. This heater turns on automatically when the power source turns off.
A Anti-condensation heater
Image Processing
Functions
Performs Black level correction and White level correction, Creating the SBU test pattern, and A/D conversion.
This machine is equipped with a short focus scanner and the SBU is located on the scanner carriage.
Operation overview
Samples 2 analog signals (ODD, EVEN) from RGB output from the 3-line CCD, and converts them to digital signals by an A/D converter. The digital signals are output to the IPU.
SP correction value storage
The SBU correction value is stored in an EEPROM on the BCU.
Execute the following SP settings when the scanner carriage is replaced. (Lens block is located on the scanner carriage.)
• SP4-871-002 (Distortion Correction Distortion Initialization)
• SP4-880-001 (Dot shift amount between R Line and G Line).
• SP4-880-002 (Dot shift amount between G Line and B Line).
SBU Test Mode
There is an SP code to create a test pattern which can be used as a diagnostic tool to troubleshoot problems in the SBU:
• SP4-699-001 (SBU Test Pattern Change)
Pattern 1: fixed value
Pattern 2: main scanning gradation pattern
Pattern 3: width scanning gradation pattern
Pattern 4: main scanning/width scanning lattice pattern
SBU has a function to generate four test patterns.
1111
1112
7. Detailed Descriptions
Image processing function overview
The image signals from the SBU are subjected to various image processing, and output to the controller (memory). The image signals from the controller (memory) are received, and output to the LDB (the LDB is provided in the write unit).
Image processing overview (copy application)
Digital signal data output from the SBU is subjected to shading correction and line interval correction, as well as image processing, which are performed by the IPU. Finally, the data is sent to the machine as digital signals-4 bit/pixels.
Image processing items
Shading correction
Details
Corrects for uneven scanner lamp lighting, and scatter in CCD light receiving sensitivity.
Line interval correction
Dot correction
Line shift during subscanning magnification/reduction by scanner.
Corrects integer part.
Line shift during subscanning magnification/reduction by scanner.
Corrects below decimal point.
Vertical line correction Corrects a vertical striped image during sheet-through ADF.
Image area separation Determines text parts and photo parts of image.
Scanner gamma correction
Filter
ADS
Color compensation preprocessing
Color compensation
Corrects scatter of image data relative to exposure amount.
From reflectivity linear to density linear.
Performs image sharpness adjustment and removes moire.
Performs natural complexion removal in full color mode.
Determines hue in masking mode, and improves chromaticity.
Image magnification change
Image shift function
Image binarization function
Converts RGB data to density value CMYK data of color materials.
Arbitrarily changes main scanning magnification, subscanning fixed image reduction and magnification of scanner image.
Shifts image data in the main scanning or subscanning directions.
In scanner mode, outputs a binary signal.
Image Processing
Image processing items
Image mask
Details
Masks an area outside a frame of an arbitrary region in scanner or printer data.
Image compression/ expansion
Printer gamma correction
Compresses or expands an image.
Adjusts exposure amount of photosensitive body relative to image density.
Gradation processing Applies 600dpi, 4bit 16 value gradation processing.
1113
7. Detailed Descriptions
Four stations (one for each color).
1114
No.
1 2nd mirror
Description
2 Laser optics positioning motor (C)
3 Laser optics positioning motor (M)
4 2nd mirror
5 Laser optics positioning motor (Y)
6 Cylinder lens
7 1st mirror
The write unit comprises a housing and the following main parts:
No.
Description
8 F-theta lens-M/Y
9 LD drive board
10 Polygon mirror motor
11 LD drive board
12 Cylinder lens
13 F-theta lens-Bk/C
14 2nd mirror
No.
1 1st mirror
Description
2 Dust shield glass
3 PCU (Y,M, C, K)
4 2nd mirror
No.
5 F-theta lens
Description
6 Soundproof glass
7 Polygon mirror motor
Laser Exposure
1115
7. Detailed Descriptions
No.
Description
1 LD drive board (M/Y)
2 LD drive board (Bk/C)
3 Cylinder lens (Bk/C)
No.
Description
4 Synchronizing detector board: Bk/C-S
5 Synchronizing detector board: M/Y-S
6 Cylinder lens (M/Y)
1116
The LD Unit is provided with two LD drive board. The beam system is a 1 beam type.
The LD drive board comprises an LD (laser diode), PD (photodiode) and LD control unit.
• The LD outputs the laser light to the PCU.
• The PD continuously detects laser light from LD, and outputs it to the LD control unit.
Laser Exposure
• The LD control unit adjusts the light amount of the LD based on the output signal of the PD.
LD control board adjustment is not required in the field.
To prevent the laser beam from turning on when the front cover or right door is open, the 5V supply to the LD drive board is interrupted when the interlock switch is open.
1117
7. Detailed Descriptions
1118
[A]: Dust shield glass
[B]: 1st mirror
[C]: F-theta lens
[D]: Polygon mirror motor
1. Mirror, lens
Laser diodes of each color emit light to match the paper transport timing. After passing through the cylinder lens (laser beam width correction), polygon mirror motor (main scanning line scan), Ftheta lens (dot position correction and optical face tangle error correction), it reaches the drums of each color.
The F-theta lens has a two-stage integrated construction, and 2 color beam correction is performed with one lens.
2. Polygon mirror motor
The polygon mirror motor comprises two (upper and lower) 6-faced mirrors formed in an integral construction (these are combined in one unit).
In this MFP, 4 color simultaneous write is performed by the LD irradiating a polygon mirror.
* The rotation speed of the polygon mirror motor is controlled by LD/ Polygon mirror motor.
3. Synchronization sensor
There are two synchronization sensors, i.e., one on the K-C side, and one on the M-Y side. Each sensor detects light from one color, and synchronization for two colors is calculated from this.
There is only one sensor for each color. The sensor at the leading edge of the main scan line has been removed.
4. Scan line inclination and automatic adjustment mechanism
The laser optics positioning motor installed on the 2nd mirror adjusts the scan line inclination.
This is done during automatic image position correction.
Process Control
The ID Sensors (also called the TM/ID sensors) are used to measure the amount of toner on the transfer belt and to correct any errors in color registration.
The TD sensor (also called the sensor) is used to measure the toner density in the developer.
The ID sensors are fixed onto the main frame, against the surface of the transfer belt. Color registration is checked by all three sensors; the front [A], center [B], and rear [C].
The center sensor [B] acts as an ID sensor and a MUSIC sensor.
In this model, a non-contact toner density (TD) sensor, which we also call a mu ( ) sensor, is used for toner density control.
The TD sensor is attached on the lower side of the development unit. Unlike a HST sensor, the board of the TD sensor is exposed. So there is a cover around the sensor to protect it and to maintain a good contact between the sensor and development unit.
The TD sensor measures the permeability of the developer without contacting it, from the outside of the case, and converts the measured value to the toner density.
1119
1120
7. Detailed Descriptions
According to the toner density measured by this sensor, the proper amount of toner is supplied to the developer.
A counter corresponding to the frequency is used as the unit of TD sensor output. Thus, unlike a HST sensor which directly detects Vt, the TD sensor output is converted into Vt for toner supply control.
In the TD sensor, there is an ID chip storing the machine identification information, the running distance information of development unit and PCU, and other information used by image density control.
Process control adjusts the condition of the imaging hardware to maintain a constant image density.
Process control is executed at the following times.
1
Process Control
PowerON
ProCon :Set
When a certain time has passed after the previous job end
(Except when recovering from an SC or jam)
Operative Condition Related SPs
SP3-530-001
SP3-530-002
SP3-530-003
SP3-530-004
SP3-530-005
SP3-530-006
SP3-530-007
SP3-530-008
2
3
JobEnd ProCon :Set
Interrupt ProCon :Set
When the value of the job end counter becomes more than the threshold
(At job end)
When the value of the job interrupt counter becomes more than the threshold
4
Non-useTime
Procon :Set
When the value of the non-use time counter becomes more than the threshold
5 Manual ProCon :Exe When SP 3-011 is used
6 Toner End Recovery
After the Toner End Status is cleared
(Recovery is NOT done in the near end status)
-
SP3-534-001 to 004
SP3-534-011 to 014
SP3-533-001 to 004
SP3-533-011 to 014
SP3-531-001 to 004
SP3-011-001 to 005
Process Control
7
Process Control
Initial Developer
Setting Process
Control
Operative Condition
When the machine detects a new PCU or development unit
-
Related SPs
Check the following SPs.
• SP3-012-001 to 010 (Front)
• SP3-012-011 to 020 (Center)
• SP3-012-021 to 030 (Rear)
Category
00 and larger
10 and larger
Result (Normal)
Code Result name
00 Not executed
11 Succeeded
41 ID sensor output error (Max)
42 ID sensor output error (Min)
40 and larger
ID Sensor
43 ID Sensor error (Max)
44 ID Sensor error (Min)
-
Description
Factory default setting (SP default)
Vt > Max
Vt < Min
Development gamma is in target, but
Vt value is less than upper limit.
Development gamma is in target, but
Vt value is less than lower limit.
1121
1122
7. Detailed Descriptions
Category
45 and larger
ID Pattern detection
Code Result name
45 ID Pattern extract error
50 Vmin_Bk/K2 error (Max)
51 Vmin_Bk/K2 error (Min)
52 K5 error (Max)
53 K5 error (Min)
54
K5 calculated approximate point error
55
56
Development gamma error
(Max)
Development gamma error
(Min)
57
58
Start developing voltage: Vk error(Max)
Start developing voltage: Vk error(Min)
90 and larger
Result(End)
59
90
99
Not enough valid data
Potential not adjusted
Stopped
Description
Cannot detect ID Pattern
K:Vmin_Bk / CMY:K2 > Max
K:Vmin_Bk / CMY:K2 < Min
K5 > Max
K5 < Min
K5 calculated approximate point <
Min
Development gamma > Max
Development gamma < Min
Start developing voltage: Vk > Max
Start developing voltage: Vk < Min
Adhesion amount data for development gamma calculation point is under 2.
Potential control method is set as
[0:FIX].
Stopped by door open, power off, error. (Set when execute.)
• Execution result example (In order of YMCK from left)
• Factory default (SP default): [00,00,00,00]
• Starting adjust: [99,99,99,99]
• Fail Vsg adjust(Y): [21,99,99,99]
• Error of Development gamma Max(C): [99,99,55,99]
• Succeeded: [11,11,11,11]
Process Control
The potential of the unexposed drum is called the electrified potential (Vd), whereas the potential when toner starts to adhere to the drum is called the development bias (Vb).
Toner starts to adhere to the drum in proportion to the potential when the value of potential becomes more than Vb. The value (coefficient) which shows the relation between the potential and the amount of adhesion is called development gamma.
In addition to the development gamma and the potential, the toner density in the developer needs to be controlled. This is done to maintain the proper toner density (the amount of toner adhesion).
The target figure for the toner density in the developer is called Vref.
Process control is done as shown in the following chart, which includes development gamma determination, Vref correction, and LD power control.
1123
7. Detailed Descriptions
1124
Electrified Potential/ Development Bias and Vref Correction are done with the following method.
The operation time differs depending on the line speed.
1. Adjusting the ID sensor Vsg
The machine adjusts the LED strength of the ID sensor so that the value of Vsg (the charge which is detected from the background on the Transfer Belt) will be in the range of 4.0V ±0.5V. When Vsg is detected as not within the target range three times, SC370 (ID sensor error) will be detected.
Process Control
• SP3-320-031/032/033 (Vsg Error Counter)
• SP3-320-013 (Vsg Upper Threshold)
• SP3-320-014 (Vsg Lower Threshold)
2. Agitating the Developer (5 seconds)
The machine agitates the developer and reads the TD sensor output.
• SP3-539-001 (Dev Agitating Time :Set)
3. Creating patterns, detecting the density
5 patterns are created on the transfer belt and detected by each ID sensor, with the Charge/
Development Bias adjusted for each pattern.
The ID sensor contains an LED [B] and two types of photo detector. The sensor detects the reflection from the LED with the positive photo detector (REG) [A] and the diffusion photo detector (DIF) [C].
4. Determining Vtref from the Development Gamma
This decides the charge voltage and development bias
LD Control is set with SP3-600-002(Process Control/ Select ProCon: LD Control).
• To use a fixed LD Power
1125
1126
7. Detailed Descriptions
Change the SP setting to [Fixed]. LD strength is fixed with SP2-221-001 to 004.
• To control LD Power by Process Control (Default)
• The LD power is determined by process control.
• The LD strength is adjusted based on a table which is determined by the Development Bias
Control and Vref Correction.
The Toner Supply Type can be selected with SP3-400-001 to 004 (Toner Supply Type).
• 0: Fixed (Fixed supply method)
The toner supply time is calculated based on the supply rate of SP3-440-001 to 004 (Fixed
Supply Mode: Fixed Rate).
• 2: PID (Proportion Integral Differential)
The amount of toner supply is calculated based on the pixel information and TD sensor information.
• 4: DANC (Divided Active Noise Control) (Default)
Conventional PID method + active noise control. It controls the timing to supply the developer to minimize uneven developer density in the development unit.
When a new PCDU is set in the machine, the machine automatically detects it and enters the developer initial setting mode. The machine then detects the count which is an output from the TD sensor. The developer initial setting is done as follows.
1.
Starting the developer initial setting mode
The new unit detection mechanism triggers the developer initial setting mode.
2.
Agitating the developer
The machine rotates the development roller and transport coil to agitate the developer for 30 seconds.
3.
Detecting the count (Initial value)
While agitating the developer, the machine detects the output from the TD sensor, and stores this output as the initial count.
4.
Calculating Vt
The machine calculates Vt using the difference of the current count while referring to the initial
count through SP.
Process Control
5.
Forced toner supply (only when newly installing the machine)
This step is required only when the machine is newly installed because there is no toner in the toner transport route.
When the developer initial setting is successfully completed, the machine stores the calculated Vt as
Vtref. The Vtref is used as a reference the next time the machine performs an initial developer setting.
SC360-01 through -04 appears if the results of step 3 are as follows:
• The count is equal or exceeds the threshold (6480 [counts]).
• The count does not match the target threshold (5800 – 6380 [counts]) three times consecutively.
Process Control and MUSIC are forcibly done after developer initial setting when a PCDU is replaced.
The machine creates correction patterns, measures the image position by reading the correction patterns, and corrects the writing position.
1
2
3
4
Power switch just turned on, or recovering from the energy save mode
Operative Condition Notes
Mode b or Mode a is done
See notes *1 and *2 below.
When printing (when the temperature has changed by a certain amount since the previous job ended, or when the number of pages printed becomes more than a set number)
End of printing (when the temperature has changed by a certain amount since the previous job ended, or when the number of pages printed becomes more than a set number)
Mode b is done
Mode b is done
Front cover opening/ closing (when the temperature has changed by a certain amount since the previous job ended)
Mode b is done
1127
1128
7. Detailed Descriptions
5
6
Operative Condition
Waiting (when the temperature has changed by a certain amount since the previous job ended, and when the number of pages printed becomes more than a set number)
When the machine detects a new PCDU, and/or image transfer belt
Notes
Mode b is done
Mode a is done
*1 Mode a: adjusted two times
*2 Mode b: adjusted once
To operate modes a, b, and c manually, use the following SPs.
• SP2-111-001 (Mode a)
• SP2-111-002 (Mode b)
• SP2-111-003 (Mode c)
Do this SP after the laser unit is changed.
• SP2-111-004 (Mode d)
Mode d is the same as doing mode c then mode a.
Normally in the field, we should only use mode d.
• Color registration errors can be corrected only by the mode d when the error is large.
Correction with higher accuracy can be performed by contacting the image transfer roller and executing
MUSIC in a condition that is almost the same as during actual printing. This process is called ‘contact
MUSIC’.
Contact MUSIC can be done manually by executing HOME screen -> User Tools icon -> Machine
Features -> Maintenance -> Color Registration (SP2-111-004).
When the Imageable Area Extension Unit is installed, the MUSIC sensor is in the printing area.
Therefore, the image transfer roller cannot be contacted and execution of MUSIC becomes the same as the previous machine.
Process Control
Items
Normal Operation
MP C2003/C2503/C2011 rough adjustment -> fine adjustment only
With Imageable
Area Extension Unit rough adjustment -> fine adjustment only
Execution time varies from model to model.
Items
Execution time
MP C2003/C2503/C2011
About 22 sec.
MP C2004/C2504 rough adjustment -> fine adjustment -> contact MUSIC rough adjustment -> fine
* Same as the previous machine
MP C2004/C2504
About 29 sec.
When MUSIC is done, the results must be checked for each color. SP2-194-007 shows whether
MUSIC was OK or NG, and SP2-194-010 to 012 show the details of the result.
• SP2-194-007 (Execution Result)
Detection Result
0 Success
1 Failure
• SP2-194-010 (Error Result: C)
• SP2-194-011 (Error Result: M)
• SP2-194-012 (Error Result: Y)
Meaning
Detection Result
0
1
2
Meaning
MUSIC not executed
Correction Succeeded: Sampling is conducted correctly and the correction is completed
Sampling Failed (When the MUSIC pattern failed to be detected)
3
4
Detection Patterns Lack (When the number of lines detected is smaller than the fixed number)
The sampled data is beyond the correction range.
(Calculated correction value is just out of rage)
1129
7. Detailed Descriptions
Detection Result Meaning
5 The sampled data is beyond the correction range.
Correction Operation Outline
1. The machine corrects the ID sensor output by Vsg adjustment
2. The machine creates the MUSIC pattern on the transfer belt with toner of each color.
3. The machine reads the MUSIC pattern on the transfer belt and detects the positions of the line patterns.
4. The machine calculates the amount of color registration or skew from the detected positions.
5. The machine determines the correction for the color registration, by calculating the required main scan magnification shift, main scan magnification deviation, main scan registration shift, skew correction value, and sub scan registration shift from the detected positions.
During printing, 5 mm patterns are created outside the normal imaging area on the transfer belt, and the image density is corrected in the real time, to improve printing of solid areas. However, note that if the optional Imageable Area Extension Unit is installed, this process is disabled.
1130
Normally, the real time control is done once every 10 sheets, but it could be done once every 5 sheets depending on the density detection level.
The frequency depends on the following SPs.
• SP3-301-001: RTP Pattern:Set:Create Intrvl:BW
• SP3-301-002: RTP Pattern:Set:Create Intrvl:FC
To see the latest result, check the following SPs. If there is an error, the result will not be updated.
• SP3-300-001 to 004 RTP Pattern:Disp:M/A(Latest):Each Color
Process Control
• SP3-300-001 to 004 RTP Pattern:Disp:M/A(Target):Each Color
IBACC (Image transfer belt type of inner ACC) maintains the quality of gradation in the images. To do this, the machine makes a gradation pattern on the transfer belt, and measures variations in density between the middle to the highlight tone, which solid printing control cannot correct perfectly. The machine feeds back variations in the density to the image-processing parameters (the digital gamma correction table).
IBACC must be done in the shortest time possible, in cooperation with process control. This is because the process requires time to adjust. If the ON/OFF setting of IBACC operation (SP3-600-030) is ON,
IBACC is done at the time of normal process control. If the setting is OFF, the IBACC is not done.
Before the IBACC procedure, the machine determines whether IBACC can be done, based on the engine condition. If there is an error in the latest process control, the following IBACC is considered to be unnecessary.
16x16 patterns are created. The order of the tones depends on the image processing layout. There are patterns for 600 dpi and 1200 dpi.
1131
7. Detailed Descriptions
1132
• SP2-111-001 (Forced Line Position Adj.: Mode a)
Executes MUSIC mode a ( fine-tune x 2)
• SP2-111-002 (Forced Line Position Adj.: Mode b)
Executes MUSIC mode b ( fine-tune x 1)
• SP2-111-003 (Forced Line Position Adj.: Mode c)
Executes MUSIC mode c (rough-tune x 1)
• SP2-111-004 (Forced Line Position Adj.: Mode d)
Executes MUSIC mode d (rough-tune then fine-tune)
• SP2-194-007 (MUSIC Execution Result: Execution Result)
Displays the execution results of MUSIC.
0: Completed successfully, 1: Failed
• SP2-194-010,-011, and -012 (MUSIC Execution Result:Error Result: C, M, Y)
Displays the details of MUSIC results for each color.
• SP3-011-001 (Manual ProCon :Exe: Normal ProCon)
Executes Pro-Con.
• SP3-011-002 (Manual ProCon :Exe: Density Adjustment)
Executes toner density adjusting Pro-Con.
• SP3-011-003 (Manual ProCon :Exe: ACC RunTime ProCon)
Process Control
Executes pre-ACC Pro-Con.
• SP3-011-004 (Manual ProCon :Exe: Full MUSIC)
Executes Pro-Con / full MUSIC.
• SP3-011-005 (Manual ProCon :Exe: Normal MUSIC)
Executes Pro-Con / normal MUSIC.
• SP3-012-001 to 010 (ProCon OK?: Front)
Displays the history for past 10 times of ProCon results code detected by the front TM/ID sensor.
The code is 2 digits per color from left, in the order of YMCK.
• SP3-012-011 to 020 (ProCon OK?: Center)
Displays the history for past 10 times of ProCon results code detected by the center TM/ID sensor.
The code is 2 digits per color from left, in the order of YMCK.
• SP3-012-021 to 030 (ProCon OK?: Rear)
Displays the history for past 10 times of ProCon results code detected by the rear TM/ID sensor.
The code is 2 digits per color from left, in the order of YMCK.
• SP3-400-001 to 004 (Toner Supply Type: Select; Bk, C, M, Y)
Selects the toner supply mode.
0: FIXED, 2: PID, 4: DANK
• SP3-530-001 to 008 (PowerON ProCon :Set)
Specifies the non-use time setting, temperature, relative humidity, absolute humidity or page interval as the threshold of process control execution determination at power on.
• SP3-531-001 to 004 (Non-useTime Procon :Set)
Specifies the non-use time setting, temperature, relative humidity, absolute humidity or page interval as the threshold of process control execution determination for during the stanby-mode.
• SP3-533-001 (Interrupt ProCon :Set: Interval:Set:BW)
Specifies the number of sheets interval for Interrupt Pro-Con (BW).
• SP3-533-002 (Interrupt ProCon :Set: Interval:Disp:BW)
Displays the number of sheets interval for Interrupt Pro-Con (BW).
• SP3-533-003 (Interrupt ProCon :Set: Corr(Short):BW)
Specifies the correcting coefficient (Short) of number of sheets interval for Interrupt Pro-Con (BW).
• SP3-533-004 (Interrupt ProCon :Set: Corr(Mid):BW)
Specifies the correcting coefficient (Mid) of number of sheets interval for Interrupt Pro-Con (BW).
• SP3-533-011 (Interrupt ProCon :Set: Interval:Set:FC)
Specifies the number of sheets interval for Interrupt Pro-Con (FC).
• SP3-533-012 (Interrupt ProCon :Set: nterval:Disp:FC)
1133
1134
7. Detailed Descriptions
Displays the number of sheets interval for Interrupt Pro-Con (FC).
• SP3-533-013 (Interrupt ProCon :Set: Corr(Short):FC)
Specifies the correcting coefficient (Short) of number of sheets interval for Interrupt Pro-Con (FC).
• SP3-533-014 (Interrupt ProCon :Set: Corr(Mid):FC)
Specifies the correcting coefficient (Mid) of number of sheets interval for Interrupt Pro-Con (FC).
• SP3-534-001 (JobEnd ProCon :Set: Interval:Set:BW)
Specifies the number of sheets interval for Job end Pro-Con (BW).
• SP3-534-002 (JobEnd ProCon :Set: Interval:Disp:BW)
Displays the number of sheets interval for Job end Pro-Con (BW).
• SP3-534-003 (JobEnd ProCon :Set: Corr(Short):BW)
Specifies the correcting coefficient (Short) of number of sheets interval for Job end Pro-Con (BW).
• SP3-534-004 (JobEnd ProCon :Set: Corr(Mid):BW)
Specifies the correcting coefficient (Mid) of number of sheets interval for Job end Pro-Con (BW).
• SP3-534-011 (JobEnd ProCon :Set: Interval:Set:FC)
Specifies the number of sheets interval for Job end Pro-Con (FC).
• SP3-534-012 (JobEnd ProCon :Set: Interval:Disp:FC)
Displays the number of sheets interval for Job end Pro-Con (FC).
• SP3-534-013 (JobEnd ProCon :Set: Corr(Short):FC)
Specifies the correcting coefficient (Short) of number of sheets interval for Job end Pro-Con (FC).
• SP3-534-014 (JobEnd ProCon :Set: Corr(Mid):FC)
Specifies the correcting coefficient (Mid) of number of sheets interval for Job end Pro-Con (BW).
• SP3-539-001 (Dev Agitating Time :Set: Time)
Specifies the developer agitating time.
• SP3-600-002 (Select ProCon: LD Control)
Specifies the LD control mode.
0:OFF, 1:ON
• SP3-600-030 (Select ProCon: IBACC:ON/OFF)
Specifies ON/OFF of IBACC.
0: OFF, 1: ON
PCDU (Photo Conductor and Development Unit)
No.
Description
1 Inner pressure adjustment filter
2 Development roller
3 OPC drum
4 Cleaning blade
5 Toner collection coil
6
Discharge lamp (installed on the main machine)
No.
7 Charge roller
Description
8 Cleaning roller (charge roller)
9 Doctor blade
10 Developer supply coil
11 TD sensor
12 Developer collection coil
Bk and CMY are both driven by motor.
1135
7. Detailed Descriptions
PCU
Bk
CMY
PCU motor: Black / ITB drive motor*
PCU motor: CMY
Drive source
* The PCU motor: Black / ITB drive motor is used to drive both the image transfer unit and the waste toner bottle.
This device uses a charge roller [B] for all four colors to reduce generation of ozone.
The charge roller, which is a rubber-covered roller that has a metal shaft, rotates in the forward direction contacting the drum [A], and applies a charge to the drum surface uniformly.
When the charge roller is dirty, an uneven charge is generated, so a cleaning roller [C] always contacts the charge roller.
1136
Residual toner on the drums after image transfer is recovered by a cleaning blade [A]. The cleaning blade is installed counter to the drum rotation in contact with the drum, and scrapes toner off.
PCDU (Photo Conductor and Development Unit)
A dry two-component magnetic brush development system is used.
The dry two-component magnetic brush development system gives a suitable electrostatic charge to the toner using magnetic particles called carriers which form a magnetic brush due to their magnetism, and cause toner to adhere electrostatically to the drum surface.
This device uses a double-coil agitation system (twin-shaft environment development system).
Toner transported from the toner cartridge to the development unit will be agitated with the developer by two toner transport coils [A] and will be delivered to the development roller.
The amount of developer adhering to the development roller is controlled by a doctor blade [B], and supplies toner to the surface of the photoconductor unit.
1137
1138
7. Detailed Descriptions
In the TD sensor (also called the sensor), there is an ID chip storing the machine identification information, the running distance information of Development unit and PCU, and other information used by image density control.
ID chip
PCDU replacement information and toner density information are stored.
In the ID chip, the following data is stored.
• Model series ID
• New PCDU information
• Color information
• Developer replacement information
• PCU replacement information
• TD sensor serial no., date of manufacture
• Date of unit installation
• Unit total counter at installation (no. of sheets, travel distance)
• Date of unit operation
• Unit total counter during operation (no. of sheets, travel distance)
• Unit parts information
• Total counter
• Total color counter
To prevent scattering of toner, the air pressure in the development unit is released via a filter.
A gear for developer coil rotation is provided on the front side of the unit (downstream side).
Drive source for Bk
PCU motor: Black / ITB drive motor
Drive source for C, M, Y
Development motor: CMY
The PCU motor: Black / ITB drive motor is also used for the image transfer unit and waste toner bottle.
Drive is switched by the development solenoid.
PCDU (Photo Conductor and Development Unit)
Applied from the development power pack via a plate spring on the front cover of the PCDU.
1139
7. Detailed Descriptions
1140
No.
Description
1 Toner bottle drive motor
2 Agitator
3 Sub-hopper
No.
4
5
Description
Toner end sensor
Toner supply motor
Toner is supplied by a Hi-Act (High Accuracy and Clean Toner) cartridge + sub-hopper.
When the toner cartridge is set, the transport nozzle on the side of the unit is inserted into the bottle (Hi-
Act system).
When the toner supply motor drives and the piezoelectric sensor in the sub-hopper detects there is no toner, the bottle drive motor rotates. The rotation of the bottle drive motor is transmitted to a transport coil via a drive gear, and toner in the bottle is transported horizontally. Due to the coil transport, stable toner supply/enhanced supply precision/reduction of residual toner are achieved.
Toner Supply
[A]: Before setting
[B]: After setting
[C]: Toner path
No.
1 Toner bottle
2 Coil spring
3 Shutter holder
Description
4 Seal
5 Shutter
No.
Description
7 Transport nozzle
8 Coil spring
9 Toner transport coil
10 Drive gear
11 Rocking spring
1141
7. Detailed Descriptions
No.
6 Shutter
Description No.
12 sub-hopper
Description
Toner transported by the coil falls directly into the sub-hopper via the transport pipe.
To prevent toner from remaining, the rocking spring in the transport pipe moves up and down together with the coil.
1142
[A]: Rocking spring
A contact type ID chip is provided in each toner bottle which stores residual toner and various toner counters, toner end history, and model serial number.
Data read and write to the ID chip contact board is performed by contact with the ID chip contact board installed in the machine.
The sub-hopper can hold Bk: 24.7 cc (equivalent to 230 sheets of 5% chart), or Color: 19.3 cc
(equivalent to 150 sheets of 5% chart) of toner.
Toner which has fallen into the sub-hopper is homogenized by an agitator (Mylar sheet: 2 for BK, 1 for each color).
After being horizontally transported by the coil, toner in the sub-hopper falls directly into the development unit.
Toner Supply
[A]: Sub-hopper: CMY
[B]: Sub-hopper: Bk
1. Transport by the Mylar sheet
2. Transport horizontally by the coil
3. Vertical drop to the development unit
4. Transport by the Mylar sheet
5. Transport horizontally by the coil
6. Vertical drop to the development unit
To shorten the recovery time after bottle replacement, the toner cartridge and sub-hopper are driven separately.
The sub-hopper is driven by a stepping motor to reduce supply variations.
In this device, there are two types of toner near end status.
The detection conditions and detection operation for each status are shown in the following table.
Control overview
1143
7. Detailed Descriptions
1144
Estimated toner end
SP3-101-001 to
004="2"
Toner end
Status
Definite toner near end
SP3-101-001 to
004="1"
Control panel message
Control panel banner display:
<Toner Cartridge is almost empty. Prepare toner cartridge replacement(s).>
Control panel banner display:
<Toner Cartridge is empty.
Printing will be suspended soon.
Replace the cartridge.>
Control panel pop-up display
(alert screen):
<Toner has been depleted.
Replace Toner Cartridge.>
Detection conditions
If the residual amount in the toner cartridge falls below SP3-110-001 to
004 (Near End Thresh) (Default: K
65g, CMY 45g)
The lesser of the "toner residual amount computed from the toner supply motor drive time" and the
"toner residual amount computed from the pixel count" is taken as the toner residual amount.
If "the toner cartridge residual amount falls below specification" and "the toner end sensor in the sub-hopper has detected toner end"
Remarks:
When toner end is detected, to use up all the toner in the cartridge, the toner cartridge is rotated for 5 seconds (full use control).
After no toner is detected again, the status becomes definite toner near end.
Toner end is defined by the following conditions (1) or (2):
(1) Determination by number of sheets and pixel count
(After definite toner near end, count is begun).
(2) Determination by Vt output
(not related to definite toner near end)
Control details
Estimated toner near end
• The toner residual amount Z (SP3-102-021 to 024) is taken as the lesser of the toner residual amount Z1 computed from the toner supply motor drive time (SP3-102-001 to 004) and the toner residual amount Z2 computed from the pixel count (SP3-102-011 to 014).
Toner Supply
• If the condition, toner residual amount Z (SP3-102-021 to 024) < near end residual amount threshold value (SP3-110-001 to 004) is satisfied, this is taken as the estimated toner near end.
Definite toner near end
Preconditions
• The toner residual amount Z (SP3-102-021 to 024) is taken as the lesser of the toner residual amount Z1 computed from the toner supply motor drive time (SP3-102-001 to 004) and the toner residual amount Z2 computed from the pixel count (SP3-102-011 to 014).
• If the condition, toner residual amount Z (SP3-102-021 to 024) < sensor near end residual amount threshold value (SP3-120-001 to 004) is satisfied, toner end sensor detection is begun to determine the definite end. (When the toner residual amount is more than the threshold value, determination by the toner end sensor is not performed).
Sensor detection
• The toner end sensor detects the sensor output every 200 ms while the polygon motor is ON, and determines whether toner is present or not from the latest 10 counts.
• The determination result is stored in the "no toner counter (SP3-121-001 to 004)".
To prevent clearing due to erroneous detection, the counter is reset if the toner end sensor detects "toner remaining" 4 times in a row.
• If the condition "no toner counter (SP3-121-001 to 004) > sensor near end determination threshold value (SP3-122-001 to 004) is satisfied, full use control which rotates the toner bottle for a certain time (SP3-163-001) is performed, and toner presence/absence determination by the toner end sensor is performed again.
• If no toner is detected after full use control determination, it is taken as definite toner near end.
Operation after changing the status to definite toner near end
• After changing the status to definite toner near end, sheet counter and pixel counter increment is begun to detect toner end.
SP3-133-011 to 014 (TE Detect :Set Page Cnt:K, C, M, Y)
SP3-133-031 to 034 (TE Detect :Set Pxl Cnt:K, C, M, Y)
Operation during definite toner near end
• When the toner supply motor drives and the toner end sensor detects no toner, the toner bottle motor drives for 2 seconds.
• If "toner remaining" is detected 4 times in a row, according to the ID chip data on the toner bottle SP3-101-001 to 004 (Toner Status :Disp) display "10" or "2" (estimated toner end).
• When it comes under the condition of Toner end pattern (1) and (2) (mentioned below), the status becomes toner end.
• After the toner bottle is replaced during definite toner near end, the machine does not execute the toner end judgement until the toner bottle motor drives for 40 or more seconds totally.
1145
1146
7. Detailed Descriptions
Toner end
Pattern (1): Determination by paper sheet counter/pixel counter
The total sheet counter and pixel counter values after definite toner near end are compared with the threshold values.
If the following "(evaluation method A=TRUE) and (evaluation method B=TRUE) or (evaluation method C=TRUE)" is satisfied, it is determined as toner end.
• Determination method A: Sheet counter (SP3-133-011 to 014) > Sheet counter threshold value (min)
• Determination method B: Sheet counter (SP3-133-011 to 014) > Sheet counter threshold value (max)
• Determination method C: Pixel counter (SP3-133-031 to 034) > Pixel counter threshold value
Pattern (2): Determination by Vt output
When the deviation between the TD sensor output value and TD sensor target value has become large, it is taken as toner end.
• After definite toner end has been determined
The difference between the output of the TD sensor (Vt: SP3-210-001 to 004) and the target value of the TD sensor (Vtref: SP3-230-001 to 004) is computed as the delta Vt, and values of the delta Vt larger than the threshold value (SP3-131-001) are integrated as "sigma delta
Vt" (SP3-132-001 to 004).
If the integration value of "sigma delta Vt" is larger than the threshold value (SP3-132-002), it is determined to be toner end.
• Before definite toner near end is determined (bottle full or estimated toner near end)
The computation is done in the same way as for definite toner near end, but separate values for the delta Vt threshold value and "sigma delta Vt" threshold value are used.
• Delta Vt threshold value before toner near end: SP3-131-011
• Sigma delta Vt threshold value before toner near end: SP3-131-012
• SP3-101-001 to 004 (Toner Status :Disp)
Displays the amount of toner remaining for each color. Uses a descending 10-step scale: 10: Full,
2: Estimated toner near end, 1: Definite toner end, 0: Toner end
• SP3-110-001 to 004 (Near End Thresh)
Sets the threshold amount of judging near-toner end.
• SP3-102-001 to 004 (Toner Remain:Disp: Bottle Motor Bk, C, M, Y)
Displays the remaining toner calculated from the motor running time.
• SP3-102-011 to 014 (Toner Remain:Disp: Pixel Bk, C, M, Y)
Displays the remaining toner calculated from imaging size.
• SP3-102-021 to 024 (Toner Remaining: Display: Fill Amount Bk, C, M, Y)
Display the filler content of new bottle.
• SP3-120-001 to 004 (TE Sn Detect Thresh: Bk, C, M, Y)
Sets the starting threshold of the near-toner end detection by the toner end sensor.
• SP3-121-001 to 004 (TE Counter: Disp: Bk, C, M, Y)
Displays the number of times the toner end sensor detected toner end.
• SP3-122-001 to 004 (TE Sn NE Thresh: Bk, C, M, Y)
Sets the number of toner end detection to start near-toner end detection.
• SP3-163-001 (Bottle Drive: Set Rotation Time at Toner End)
Sets the empty turn time[ms] at almost toner-end.
• SP3-133-011 to 014 (TE Detect :Set Page Cnt:K, C, M, Y)
Displays the amount of sheets printed after toner near end is fixed.
• SP3-133-031 to 034 (TE Detect :Set Pxl Cnt:K, C, M, Y)
Displays the amount of toner used in cm2 after toner near-end is fixed.
• SP3-210-001 to 004 (TD.Sens:Vt :Disp: Current: K, C, M, Y)
Displays the latest TD sensor output.
• SP3-131-001 (Vt TE Thresh: Delta Vt Thresh)
Specifies the threshold to start adding the delta Vt after toner Near End.
• SP3-132-001 to 004 (Delta Vt Sum: Bk, C, M, Y)
Displays the integrated value of delta Vt.
• SP3-131-011 (Delta Vt Thresh BF NE)
Specifies the threshold to start integrating delta Vt before toner Near End.
• SP3-131-012 (Delta Vt Sum Thresh BF NE)
Specifies the threshold of delta Vt to check Toner End before toner Near End.
Toner Supply
1147
7. Detailed Descriptions
No.
Description
1 Waste toner bottle full sensor
No.
Description
2 Waste toner bottle set sensor
1148
The waste toner bottle set sensor is at the rear of the waste toner bottle.
If the waste toner bottle is not set, this switch is OFF, so imaging is prohibited, and "Waste toner bottle is not set. Please contact service department." is displayed on the control panel.
Driven by the "PCU motor: Black / ITB drive motor".
Waste toner from the PCU and Image transfer unit is collected in the transport path at the front of the machine, and arrives at the entrance to the waste toner tank.
Waste Toner
PCU waste toner transport path
Waste toner recovered by the cleaning blade is transported from the rear of the PCU to the transport path at the front of the machine by the waste toner transport coil.
Image transfer unit waste toner transport path
Waste toner recovered by the Image transfer cleaning unit is transported from the rear of the Image transfer cleaning unit to the transport path at the front of the machine by the waste toner transport coil.
[A]: Image transfer unit waste toner transport path
[B]: PCDU
[C]: PCU waste toner transport path
[D]: Waste toner bottle
The waste toner bottle full sensor is at the top of the waste toner bottle. When the waste toner in the bottle has reached approximately 90%, the sensor lifts up a feeler, and an actuator blocks the waste toner bottle full sensor. After sensor detection, the remaining number of days of use is decremented from
18 by the pixel counter.
Full detection flow
1. When waste toner reaches approximately 90% of the bottle capacity, the full sensor switches
ON.
2. When the waste capacity sensor switches ON, the days remaining counter is decremented from 18.
3. Days remaining counter: At 15 days to go, a @Remote warning is given (only in models with
@Remote connection).
1149
1150
7. Detailed Descriptions
4. Days remaining counter: At 5 days to go, a control panel message (Waste toner bottle is nearly full. Please contact service department.) is displayed. (Nearly full)
5. Days remaining counter: At 0 days to go, a control panel warning is displayed, and the machine stops.
• After the full sensor switches ON, before nearly full, if the waste toner bottle full sensor has been switched OFF, it is determined that the waste toner bottle has not been replaced, and countdown of the days remaining counter continues.
• The days remaining counter starts computing when a new bottle is detected, and displays the days remaining, whose upper limit is 255 and lower limit is 18, until the waste toner bottle full sensor is first switched ON.
• After the full sensor was first switched ON, the days remaining which is computed from when the sensor switched ON is displayed (upper limit is 18)
• When the bottle is replaced before the machine detects a full waste toner bottle and stops printing, it is necessary to reset PM counters manually (SP3-701-142).
• When the bottle is replaced after the machine stopped due to detecting a full waste toner bottle, it is not necessary to reset PM counters. If the counters are reset, the replace counter will count up twice.
SP descriptions
• SP3-701-142 (Manual New Unit Set: Waste Toner Bottle)
Enables/disables the new unit detection function. When this function is ON, the machine automatically resets the PM counter when a new unit is detected.
The latch which existed with the previous machine has been removed for this machine.
The waste toner cover is opened by pulling the 1 st
paper tray, and inserting a finger into the gap (red circle) shown below.
Waste Toner
The waste toner cover of the previous machine (MP C2003/C2503/C2011) is opened by pressing it with your fingers.
1151
1152
7. Detailed Descriptions
No.
Description
1 Image transfer unit
2 Image transfer belt cleaning unit
3 PCDU
No.
Description
4 Paper transfer roller
5 Laser exposure unit
Image Transfer and Paper Transfer
No.
1 ITB drive roller
Description
2 Discharge plate
No.
Description
3 Paper transfer roller
The image transfer belt is driven by the "PCU motor: Black/ ITB drive motor" via the gear and the ITB drive roller.
1153
7. Detailed Descriptions
[A]: Image transfer belt
[B]: ITB drive roller
[C]: PCU motor: Black/ ITB drive motor
The bias to the Image transfer belt is applied to the image transfer roller of each color from the transfer power pack.
1154
[A]: Image transfer belt
[B]: Image transfer roller
The 5 springs, in order from the right (double-side unit), consist of "C (cyan), secondary transfer, BK
(black), Y (yellow) and M (magenta)" transfer bias terminals.
To prevent early deterioration of the color photosensitive drum, the Image transfer belt unit is provided with a contact/separation mechanism and, during monochrome printing, separation of the image
Image Transfer and Paper Transfer transfer belt from the color photosensitive drum is controlled. Contact/separation of the image transfer belt unit is performed via a gear from an ITB contact and release motor (also used as a magenta toner supply motor). Separation or contact is detected by the ITB contact and release sensor.
[A]: Slider
[B]: Drum
[C]: Contact and release cam
[D]: ITB contact and release motor (also used as a magenta toner supply motor)
[E]: ITB contact and release sensor
[F]: Guide
[G]: Image transfer roller
FG Control is performed (Frequency Generator control: ensures precision of motor operation)
By arranging the imaging sequence in the order Y > M > C > Bk, cyan is laid on top of magenta, which increases tolerance to image blurring and image reddening when dark blue is output, and improves image quality.
Image transfer cleaning is performed by a cleaning blade (counter method).
Due to downsizing of machine width, the cleaning unit is installed on top of the image transfer unit.
Therefore, to replace the cleaning unit, replacement must be performed after taking out the Image transfer unit and inverting it.
1155
7. Detailed Descriptions
1156
[A]: Toner collection coil
[B]: Image transfer belt
[C]: Image transfer cleaning blade
[D]: Toner collection coil
A bias is applied to the ITB drive roller to transfer the image on the image transfer belt to the paper
(repulsion transfer). As there is no paper between the image transfer roller and toner image, this method is not easily affected by paper conditioning.
Also, toner adsorption on the paper is facilitated by the static charge eliminator of the paper transfer unit
(no charge is applied).
The rotation of the paper transfer roller follows that of the ITB drive roller.
If the paper transfer roller is permanently in contact with the image transfer belt, toner on the Image transfer belt moves to the roller and soils the underside of the paper surface, therefore the Paper transfer roller is separated during process control or MUSIC control (it is not separated during real-time process control).
Separation of the paper transfer roller is achieved by transmitting the drive of the paper transfer contact motor via the ITB unit joint.
Image Transfer and Paper Transfer
[A]: TM/ID sensor (center)
[B]: Paper transfer roller HP sensor
[C]: Paper transfer contact and release motor
[D]: Cam
[E]: Paper transfer roller
[F]: ITB drive roller
To achieve paper separation, a curvature separation method which separates the paper transfer roller and Image transfer belt is employed.
1157
7. Detailed Descriptions
[A]: TM/ID sensor (front)
[B]: TM/ID sensor (center)
[C]: TM/ID sensor (rear)
1158
[A]: Paper transfer roller (standard roller)
[B]: Paper transfer roller (Imageable Area Extension Unit Type M19)
When Imageable Area Extension Unit (316mm) is equipped, 316mm width printing is done instead of
Real Time Process Control at margin.
Paper Feed/ Transport Section
No.
Description
1 Pick-up roller (1st paper tray)
2 Paper feed roller (1st paper tray)
3 Friction roller (1st paper tray)
No.
Description
4 Paper feed roller (2nd paper tray)
5 Friction roller (2nd paper tray)
6 Pick-up roller (2nd paper tray)
In this machine, an RF paper feed system is employed, and the paper feed roller, friction roller and pickup roller are high durability rollers.
The paper feed tray consists of 2 units, i.e., a main double tray and a bypass feed tray. By using the 1st tray as a fixed tray, and the 2nd tray as a universal tray, a space-saving two-step feed is enabled.
1159
1160
7. Detailed Descriptions
Tray
1st paper tray
2nd paper tray
Bypass feed tray
Duplex unit
Paper size
A4 landscape - A5 landscape
SRA3 - postcard
SRA3 - postcard
SRA3 - A6 portrait
Loading number of sheets
550 sheets
550 sheets
100 sheets
Interleave
Corresponding paper thickness
60 to 300 g/m
2
60 to 300 g/m
2
60 to 300 g/m
2
60 to 169 g/m
2
When the paper feed tray is set in the machine, the set switch at the rear of the tray switches ON, and it is detected that the tray is set.
The coupling between the shaft at the rear of the tray and the lift motor then engages, the motor rotates, and the tray base plate is lifted. The tray base plate lifts until the paper surface pushes the pick-up roller up, the upper limit sensor switches OFF (interrupt), and the machine enters paper feed standby mode.
When the tray is removed, the coupling is released, and the base plate moves down. The lift motor then rotates until the coupling returns to the home position.
Paper Feed/ Transport Section
No.
1 Lift motor
2 Coupling
Description No.
3 Tray rear shaft
Description
4 Tray bottom plate
1161
7. Detailed Descriptions
No.
Description
1 Upper limit sensor
No.
2 Pick-up roller
Description
1162
No.
Description
1 Pick-up arm
2 Upper limit sensor
3 Pick-up roller
No.
4 Paper feed roller
5 Feed guide
6 Friction roller
Description
Paper Feed/ Transport Section
The paper feed unit employs an RF system.
In a conventional FRR system, transport of 2 sheets at a time is prevented by reverse rotation of the separating roller, but in the RF system, paper separation is assisted by the resistance of a separating roller with a torque limiter (reverse drive is not performed).
When the paper feed tray is set in the machine, the pressure release lever is pressed, the Friction roller comes in contact with the paper feed roller, and the pick-up roller contacts the top of the paper (to prevent paper remaining, when the paper feed tray is withdrawn, the arm returns and contact with the rollers is released).
The machine enters paper supply standby mode when the tray bottom plate moves up. When the paper feed motor is switched ON, the rollers rotate and paper is supplied.
The roller holder functions as a paper guide and roller clip ring. The roller holder prevents the paper from winding up.
1163
1164
7. Detailed Descriptions
No.
Description
1 Pressure release lever
2 Friction roller
No.
3 Pick-up roller
Description
In this machine, to maintain the paper gap constant, switching the paper feed roller ON/OFF adjusts the paper feed timing.
1.
The paper feed motor is switched ON, and the first sheet is supplied.
2.
Just before the rear edge of the first sheet leaves the paper feed roller, the paper feed motor switches OFF.
3.
When the first sheet is fed a predetermined distance by the downstream transport roller, the paper feed motor switches ON to supply the second sheet of paper.
Size cannot be detected only with set detection.
• 1st tray settings:
A4 LEF, LT LEF, B5 LEF, and A5 LEF (select with UP mode, default is A4 LEF)
The end fence interlocking rotation detection plate is an automatic detection system which recognizes patterns by a 4-position push switch.
Size is detected by the detection patterns of knobs 1, 2, 3, and 4. Tray set is detected by another switch.
If there has been a change in the pattern, "MFP tray automatic size detection" control is performed continuously.
If the paper size is selected manually by user setting, the automatic size detection is overridden.
Paper Feed/ Transport Section
No.
Description
1 End fence
2 Paper size switch
No.
Description
3 Size detection actuator
4 Tray set switch
2nd tray detection sizes:
SRA3, A3, B4, A4 SEF, LT SEF, B5 SEF, A4 LEF, B5 LEF, and A5 LEF
2nd tray size detection patterns:
SRA3(12"×18")
A3(DLT)
B4(LG)
A4 portrait
LT portrait
B5 portrait
A4 landscape(LT landscape)
Size
4
1
0
0
0
1
1
1
0
1
0
0
1
0
1
1
3
0
Knob
2
1
0
1
1
1
0
0
0
0
0
1
0
1
1
0
1
0
1165
1166
7. Detailed Descriptions
B5 landscape(Exe landscape)
A5 landscape
Size
4
0
0
3
0
1
Knob
2
1
0
* "0" is switch ON (PUSH), "1" is switch OFF.
* The figures in parentheses are automatic paper size switch can be switched over in SP mode (for SP settings, see "SP mode (paper supply transport)": SP5-181-002 to 006).
* SRA3=320×450mm(12.6"×17.7")
* Exe LEF=10.5"×7.25"
* If a pattern other than the above is detected, a blank is displayed on the control panel.
1
0
1
When the lift motor rotates, the remaining paper sensors 1, 2 [A] built into the motor switch ON
(unblocked) or OFF (blocked). Paper remaining in the paper feed tray is detected by the combination of
ON/OFF for the two sensors.
Paper Feed/ Transport Section
There are the following 4 remaining paper detection levels:
Remaining paper status
Remaining paper status sensor 1
Remaining paper status sensor 2
Control panel remaining paper display
100%
ON
ON
Bar 4
70%
OFF
ON
Bar 3
30%
OFF
OFF
Bar 2
10%
ON
OFF
Bar 1
When there is no more paper in the paper feed tray, the leading edge of the paper end feeler falls into a notch in the base plate, and the paper end sensor at the rear edge of the end filler switches ON
(pass).
1167
7. Detailed Descriptions
1168
No.
Description
1 Paper end sensor
2 End feeler
No.
3 Notch
Description
The 1st/2nd pick-up rollers and 1st/2nd paper feed rollers are driven by the paper feed motor. The
1st/2nd separation rollers are driven by the transport motor.
The bypass transport roller is driven by the bypass/duplex motor, and the registration roller is driven by the registration motor.
Paper Feed/ Transport Section
No.
Description
1 Paper feed motor
2 Transport motor
3 Pick-up roller (1st tray)
4 Paper feed roller (1st tray)
5 Transport roller (1st tray)
No.
Description
6 Bypass transport roller
7 Transport roller (2nd tray)
8 Paper feed roller (2nd tray)
9 Pick-up roller (2nd tray)
1169
7. Detailed Descriptions
1170
No.
Description
1 Registration roller (Driven)
2 Registration roller (Drive)
No.
Description
3 Registration motor
The registration mechanism removes paper scraps using the paper removal Mylar in contact with the driven roller (resin). Paper scraps removed by the paper removal Mylar are collected in the paper dust container.
Paper Feed/ Transport Section
No.
Description
1 Paper dust container
2 Paper dust removal Mylar
No.
Description
3 Registration roller (Driven)
4 Registration roller (Drive)
1171
7. Detailed Descriptions
1172
No.
Description
1 Manual feed lever end sensor
2 Bypass paper feed roller
3 Bypass pick-up roller
No.
Description
4 Bypass/Duplex motor
5 Bypass/Reverse roller
6 Paper detection filler
The bypass paper feed mechanism employs an FRR system. The bypass paper feed unit comprises a paper feed roller, reverse roller and pick-up roller.
When the paper feed tray is selected and the machine is started, the bypass pick-up solenoid is switched
OFF, and paper is supplied by the bypass/duplex motor (CCW).
In standby mode, the bypass pick-up roller is not in contact with the paper surface. This is opposite to the paper feed tray.
Paper Feed/ Transport Section
Paper size width detection is performed by the bypass width sensor (rotary switch).
The bypass feed size switch has a rotation plate which rotates together with the side fence of the bypass feed table, and detects the paper size.
Paper portrait/landscape is determined by the length sensor.
Two feelers [A] for the bypass length sensor [B] are added to the rear of the tray to prevent false detection of paper length caused by floating at the rear of paper when long paper is set without pulling out the bypass tray extension.
To detect bypass feed paper end, a paper detection feeler and bypass feed paper end sensor are provided.
When the paper is set, the bypass feed paper end sensor switches ON (interrupt), and paper set is detected.
When there is no more paper, the detection feeler falls into a hole in the bypass feed table, the bypass feed paper end sensor switches OFF (pass), and paper end is detected.
The paper feed roller, Reverse roller and pick-up roller are driven by the bypass/duplex motor.
1173
7. Detailed Descriptions
1174
No.
1 Reverse sensor
Description
2 Duplex entrance roller 1
3 Duplex entrance sensor
4 Duplex entrance roller 2
5 Duplex transport roller
No.
Description
6 Duplex exit roller
7 Duplex exit sensor
8 Registration roller
9 Paper exit junction gate
10 Reverse roller
The paper passes through the junction gate, and is fed to the duplex unit past reverse rotation sensor and reverse rotation roller.
Paper Feed/ Transport Section
No.
Description
1 Fusing exit sensor
2 Reverse sensor
3 Reverse roller
No.
Description
4 Paper exit junction gate
5 Duplex entrance roller 1
The rollers are driven by the following motors:
Rollers
Reverse roller
Duplex entrance roller 1
Duplex entrance roller 2
Duplex transport roller
Duplex exit roller
Drive sources
Reverse motor
Duplex entrance motor
Duplex entrance motor
Bypass/ Duplex motor
Bypass/ Duplex motor
The duplex unit, in order to reduce the overall duplex copying time, performs interleaving.
Paper exit from main machine
1175
1176
7. Detailed Descriptions
Length
Less than 216 mm
216-432 mm
432-457.2 mm
1-bin tray exit from main machine
Length
Less than 216 mm
216-432 mm
2
1
3
2
1
No. of interleaves
No. of interleaves
• 3 sheet interleave
1 sheet undersurface -> 2 sheet undersurface -> 3 sheet undersurface -> 1 sheet top surface -> 4 sheet undersurface -> 2 sheet top surface
• 2 sheet interleave
1 sheet undersurface -> 2 sheet undersurface -> 1 sheet top surface -> 3 sheet undersurface -> 2 sheet top surface -> 4 sheet undersurface
3-sheet interleaving
Paper Feed/ Transport Section
No.
1 Reverse sensor
Description
2 Reverse roller
3 Paper exit junction gate
4 Duplex entrance roller 1
No.
Description
5 Duplex entrance sensor
6 Paper exit sensor
7 Paper exit roller
The paper fed from the fusing unit is changed over by the junction gate in the "Paper exit/bridge unit" direction or the "duplex unit/1-bin tray" direction.
Machine paper exit/bridge unit direction
1. The registration sensor switches ON.
2. The paper exit/pressure release motor switches ON (CCW).
1177
7. Detailed Descriptions
3. When the rear edge of the paper leaves the paper exit roller, the paper exit/pressure release motor switches OFF.
1178
No.
1 Paper exit roller
Description
2 Paper exit sensor
3 Paper exit junction gate
Duplex unit/1-bin tray direction
1. Registration sensor switches ON.
2. The reverse motor switches ON (CCW).
3. Before the leading edge of the paper reaches the paper exit junction gate, the junction gate moves to the duplex unit/1-bin tray direction.
* If the gate is in the duplex unit/1-bin tray direction, the gate is not changed over.
4. Before reversing the paper, the paper exit solenoid switches OFF.
5. When the rear edge of the paper leaves the reverse roller, the reverse motor switches OFF.
Paper Feed/ Transport Section
No.
1 Reverse sensor
2 Reverse roller
Description
3 Paper exit junction gate
Paper exit full detection
This machine has no paper exit full sensor.
Paper exit jam detection
Paper exit jam is detected by the paper exit sensor.
1179
1180
7. Detailed Descriptions
Paper Feed/ Transport Section
Output
Pick-up roller 1
Paper feed roller 1
Pick-up roller 2
Paper feed roller 2
Transport roller 1
Transport roller 2
Registration roller
Paper exit roller
Reverse roller
Duplex entrance roller 1
Duplex entrance roller 2
Duplex transport roller
Duplex exit roller
Bypass feed transport roller
Bypass pick-up roller
Bypass paper feed roller
Bypass reverse roller
ITB drive roller (belt)
Paper transfer roller
Fusing drive roller
Paper feed motor
Transport motor
Registration motor
Paper exit/ Pressure release motor
Reverse motor
Duplex entrance motor
Bypass/Duplex motor
Drive source
ITB drive motor
ITB drive roller (Follows rotation of image transfer belt)
Fusing motor
1181
1182
7. Detailed Descriptions
2nd tray pick-up roller
Output
1st tray pick-up roller Paper feed motor
Paper exit junction gate
Drive source
Paper feed motor
Paper exit solenoid
Bypass pick-up roller Bypass pick-up solenoid
Default position
Pressure contact when
OFF
Pressure contact when
OFF
Paper exit path open when OFF
Clearance when OFF
Application
Loaded paper contact and release changeover
Loaded paper contact and release changeover
Paper exit/ bridge unit or 1-bin/duplex path change-over
Loaded paper contact and release changeover
Distance units: mm
Md.
1st tray paper feed
2nd tray paper feed
From
Pick-up roller 1
Paper feed roller 1
Pick-up roller 2
Paper feed roller 2
Transport roller 2
Transport roller 1
Registration
Registration roller
Fusing
Paper exit
Paper transfer roller (nip)
Fusing roller (nip)
Fusing roller (nip)
To
Paper feed roller 1
Transport roller 1
Paper feed roller 2
Transport roller 2
Transport roller 1
Registration roller
Paper transfer roller (image transfer position)
Fusing roller (nip)
Fusing exit roller
Paper exit roller
95.5
85.0
55.7
143.6
Distance
30.0
43.0
30.0
43.0
96.9
86.8
Md.
Two-way distribution
Duplex re-supply
Bypass feed
From
Fusing roller (nip)
Reverse roller
Duplex entrance roller 1
Duplex entrance roller 2
Duplex transport roller
Duplex exit roller
Bypass pick-up roller
Bypass paper feed roller
Bypass transport roller
Distance units: mm
Md.
1st tray paper feed
From
Transport roller 1
2nd tray paper feed
Registration
Paper exit
Two-way distribution
Transport roller 2
Transport sensor 2
Registration sensor
Paper exit sensor
Reverse roller
Duplex
1-bin
Duplex entrance roller
Duplex exit roller
Reverse sensor
Paper Feed/ Transport Section
To
Reverse roller
Duplex entrance roller 1
Duplex entrance roller 2
Duplex transport roller
Duplex exit roller
Registration roller
Bypass paper feed roller
Bypass transport roller
First transport roller
Distance
143.6
131.3
120.4
90.9
110.2
94.7
30.0
24.5
56.0
To
Transport sensor 1
Transport sensor 2
Transport sensor 1
Registration roller
Paper exit roller
Reverse sensor
Duplex entrance sensor
Duplex exit sensor
1-bin paper exit roller
Distance
16.8
24.3
88.7
17.2
17.0
14.0
25.0
-
15.0
1183
7. Detailed Descriptions
Paper Exit Driven Roller
The standard paper exit driven roller [B] is drum-shaped and improves the stacking performance of the main machine exit tray by adding stiffness to the paper. However, if the paper has too much stiffness, it may jam as it enters the optional paper path when the internal peripheral is connected.
Therefore, a flat type driven roller [A] is used to reduce the stiffness when transporting the paper.
The following options use the flat type driven roller:
• Internal Finisher SR3130
• Bridge Unit BU3070
• Internal Finisher SR3180
• Side Tray Type M3
Paper Support Guide
To prevent paper jam when the paper is delivered from the machine’s paper exit to the internal exit peripherals, attach the paper support guide [C] (supplied with the peripherals).
1184
When paper larger than A3 is set, wrinkles may appear at the end of the paper. As a countermeasure, the previous machine used an L-shaped sheet metal [B].
Paper Feed/ Transport Section
In this machine, the support components [A] and a decal are attached, which are also available to the end-user.
For small size paper, the side fences [B] are sufficient because the paper is light, but paper larger than A3 must be set at the position indicated by the decal.
1185
1186
7. Detailed Descriptions
Tray 2, Paper Feed Unit PB3220/PB3210 (D787), and Paper Feed Unit PB3150 (D694) are also changed from L-shaped sheet metal to support component.
Factory Default:
• Tray 2: A3 (11 inches for NA only)
• Optional Paper Tray: A3 for all regions
This machine employs a QSU fusing system wherein a lamp emits light to heat a sleeve belt.
Fusing
No.
Description
1 Fusing sleeve thermostats
2 Non-contact thermistor
3 Thermopile
4 Fusing sleeve belt
5 Stripper Plate
No.
Description
8 Fusing junction gate
9 Fusing exit roller (drive)
10 Pressure roller drive cam
11 Pressure roller
12
Pressure roller thermistors: Center, Edge, and Full-bleed edge
1187
7. Detailed Descriptions
No.
Description
6 Fusing exit guide plate
7 Fusing exit roller (driven)
No.
Description
13 Fusing entrance guide plate
1188
No.
Description
1 Thermopile (edge)
2 Thermopile (center)
3 Fusing lamp
4 Fusing sleeve thermostat (edge)
5 Fusing sleeve thermostat (center)
No.
Description
6 Non-contact thermistor (center)
7 Pressure roller thermistor (center)
8 Non-contact thermistor (edge)
9 Pressure roller thermistor (edge)
10 Pressure roller thermistor (Full-bleed edge)
Fusing
No.
Description
1 Fusing lamp (center)
2 Fusing lamp (edge)
3 Fusing sleeve belt
No.
4 Reflector
Description
5 Heat conduction plate
6 Nip pad
E-QSU (Enhanced-Quick Start Up) fusing
This fusing unit has the heat conduction plate added to the pressure pad on the fusing nip and removed the shield plate control.
The model of 35 cpm or below require little amount of heat, so it controls the temperature by the heat conduction plate and lamp control at the edges and center.
The heat conduction plate on the nip (on the surface of the pressure pad) disperses the temperature deviation between the front and rear parts of the fusing sleeve belt, so as to even out the temperature.
A fusing sleeve belt is driven by drag rotation following a pressure roller, and presses a nip pad against the pressure roller to fix toner on the paper.
The fusing lamp heats the fusing sleeve belt, and the area of the belt which is heated moves in an anticlockwise direction so that heat is transmitted up to the contact point with the pressure roller.
Lamps
There are two lamps.
1189
1190
7. Detailed Descriptions
Lamp power:
Center
Edge
NA/TWN
647 W
344 W
EU/AA/CHN
700 W
527 W
Nip pad
Presses against the pressure roller to form a fusing nip. The top surface is covered with a slippery sheet.
Reflector
Transmits heat efficiently to the fusing sleeve belt.
Flanges
Situated on both ends of the fusing sleeve belt. They maintain the shape of the belt.
Heat conduction plate
Disperses the temperature deviation between the front and rear edges of the fusing sleeve belt to make the temperature uniform.
The pressure roller [B] is driven by the fusing motor [A].
The fusing sleeve belt [C] is driven by the pressure roller (drag rotation).
Fusing
The pressure release mechanism helps the user to remove paper jams from the fusing unit more easily. A pressure lever [C] is released by the drive of the paper exit/pressure release motor [A], and the pressure roller [D] separates from the fusing sleeve belt.
The pressure roller HP sensor [E] detects the encoder [B], and determines the position of the pressure roller.
After replacing the pressure roller, if the sensor does not detect the encoder for 3 times continuously after a job is completed, SC569-00 (Paper Exit/ Pressure Release Motor Error Detection) is generated.
1191
7. Detailed Descriptions
1192
Warm-up mode
After power ON, fusing warm-up begins. The fusing motor is switched ON, the halogen lamp is energized, and the fusing temperature is increased to the "reload target temperature."
When fusing warm-up is completed, the fusing motor stays ON for a certain time, and the fusing temperature is maintained at the "reload target temperature."
Standby mode
After fusing reload, when a certain time has elapsed, power supply to the halogen lamp is switched OFF, and the fusing motor is switched OFF. At the same time, the temperature is maintained at the "standby target temperature (SP1-107-001)" by the halogen lamp.
In standby mode, the Fusing motor rotates once every 60 minutes.
The operation interval of the Fusing motor can be changed by SP1-122-001 (Standby Rotation
Setting Rotation Interval) but the change may cause the uneven glossiness on the image.
Fusing
Printing ready mode
After returning to standby mode, the halogen lamp is re-energized, and the fusing temperature is raised to the "printing ready target temperature." If printing is not required, the machine again enters the standby mode after a certain time has elapsed.
If printing is required in standby mode during return, the halogen lamp is energized, the fusing temperature is increased to "target temperature after reload/after paper feed," and the print job starts.
To maintain image quality and machine quality, this machine has a low-temperature CPM mode and high-temperature CPM mode, and implements 3 levels of CPM down according to the usage situation and machine state.
Low-temperature CPM mode
In a low-temperature environment, the fusing lamp cannot keep up, and it may be difficult to maintain the fusing target temperature. To handle this, the detection temperature of the fusing center thermopile is checked every few seconds, and if the detection temperature during the check is below a threshold value, the CPM is decreased by 1 level.
This low temperature CPM reduction is performed in the following 3 levels:
CPM down level
Mode Level
Normal CPM 100%
CPM down 1
CPM down 2
CPM down 3
80%
65%
50%
Hot CPM mode
To shorten warm-up time and reduce the TEC value, this machine employs a fusing unit with a low heat capacity.
For this reason, the temperature of those parts of the fusing sleeve belt where paper does not pass easily increases, and the outside of the paper width may get extremely hot. In order to prevent the belt breakage due to this excessive temperature rise, CPM down is implemented depending on the usage conditions. CPM down can be implemented in the following 3 levels depending on the detection temperature of the temperature sensor, or the paper passage time.
1193
1194
7. Detailed Descriptions
• The down level % is a value for the case where a typical paper (Normal paper: A4 or smaller paper sizes) passes through the SEF at normal speed. There may be some differences depending on paper size/paper thickness.
CPM down level
Mode Level
Normal CPM 100%
CPM down 1
CPM down 2
CPM down 3
80%
50%
30%
CPM down determination using a temperature sensor
The temperature sensor is checked at given intervals, and if the detection temperature is above a threshold value, the CPM is decreased by 1 level.
Since the points at which temperature tends to increase depend on the paper size, the sensor used is changed depending on the paper size.
Paper width (length)
A3/DLT/B4
LT/A4
B5/A5/B6/A6
Check sensor
Pressure roller thermistor (edge)
Thermopile (edge)
Pressure roller thermistor (center)
CPM down determination using paper passage time
Depending on the paper size, it may not be possible to determine the points on the fusing sleeve belt which tend to rise in temperature by a sensor.
Therefore, time conditions are also used to determine CPM down, and if continuous paper passage time is above a threshold value, CPM is decreased by 1 level.
(When CPM down is performed by time conditions, CPM does not increase thereafter.)
This machine provides a curl reduction mechanism on the fusing exit.
Fusing
Curling is reduced by bending in the reverse direction of the curl created at the fuser nip and forcibly adding resilience using the fusing exit roller [B], fuser exit driven roller [C], and fusing junction gate [A], located at the fuser nip exit.
The fusing junction gate is retracted for duplex printing/thick paper to prevent image smearing.
Drive
The fusing junction gate [C] is rotated via the arm [B] by turning ON the fusing exit drive solenoid
[A] located on the main machine side.
When the solenoid is ON, the fusing junction gate is at no curl correction position.
1195
7. Detailed Descriptions
When the solenoid is OFF, it is put in the continuous curl correction position by spring [A].
1196
Availability of curl correction by print mode
For duplex printing, or using thick paper, the fusing junction gate is retracted to prevent image smearing.
: Curl corrected (one-side printing only)
-: Curl not corrected
Normal Paper
Recycled Paper
Color Paper
Special Paper 1
Thin
Paper
Plain
Paper
1
Plain
Paper
2
Middle
Thick
-
-
-
-
Thick
Paper
1
-
-
-
-
Thick
Paper
2
-
-
-
-
Thick
Paper
3
-
-
-
-
Thick
Paper
4
-
-
-
-
Fusing
Special Paper 2
Special Paper 3
Letterhead
Preprinted Paper
Bond Paper
Cardstock
OHP
(Transparency)
Label Paper
Coated: Matte
Envelope
Coated: Glossy
Thin
Paper
-
-
-
-
Plain
Paper
1
-
-
-
-
Plain
Paper
2
Middle
Thick
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Thick
Paper
1
-
-
-
-
-
-
-
-
Thick
Paper
2
-
-
-
-
-
-
-
-
-
-
-
Thick
Paper
3
-
-
-
-
-
-
-
-
-
-
-
SP1-907-096 (Operation Setting: Fusing Exit SOL Setting)
By changing SP1-907-096, the curl correction mechanism can be enabled regardless of the paper setting.
If the fusing exit drive solenoid is ON, the curl correction function is OFF.
If the fusing exit drive solenoid is OFF, the curl correction function is ON.
SP value
0
1
2
3
4
Curl Correction
Tray Bypass
Normal Operation
Normal Operation Always OFF
Always OFF
Always OFF
Normal Operation
Normal Operation
Always OFF
Always ON
-
-
-
Thick
Paper
4
-
-
-
-
-
-
-
-
1197
1198
7. Detailed Descriptions
SP value
5
6
Tray
Always ON
Always ON
Curl Correction
Bypass
Normal Operation
Always ON
For duplex printing, or printing to 1-bin tray, always no curl correction regardless of the SP setting, because the fusing junction gate would interfere with the transfer path.
Electrical Parts
Controls the MFP system overall. Comprises an x86CPU, controller ASIC, IO control ASIC, and RAM.
Scanning control circuit which performs analog signal processing and AD image conversion of the CCD scanned image.
It also has an IPU I/F, and controls scanner input output signals according to CPU commands.
1199
7. Detailed Descriptions
1200
LD control circuit which drives the laser diode with a universal driver.
Controls the engine.
Processes digital signals.
The SIO functions are included in the IPU for this machine. Thus the SIO board is removed.
SIO Function
Circuit which controls generation of SBU power, scanner internal sensor I/F, carriage drive stepping motor and LED drive.
Proximity sensors (human detection sensors) and proximity sensor (human detection sensor) board are equipped.
People are detected by IR sensors which sense the temperature difference between the human body and the temperature of the machine location.
Controls the MFP engine sensor, motor and solenoid.
Controls the fax program.
Controls the control panel.
Generates the high-voltage power required for process control. Divided into two units, i.e., transfer (TTS) and electrostatic/developing (CB).
Electrical Parts
Generates DC power from a commercial AC power supply, and supplies it to each control circuit.
Comprises an A/C drive circuit for controlling the fixing heater.
The power circuit of the anti-condensation heaters for scanner and PCDU is linked to the switch of the paper feed tray heater. Therefore, when the paper feed tray heater power is turned OFF, all heaters are de-energized. In addition, the operation during printing is controlled so as not to exceed the maximum power.
The behavior of the heaters when the machine is in standby mode is controlled by SP5-805-001 (Anti-
Condensation Heater OFF/ON).
Heater
SP5-805
-001
OFF(0)
Plug-in
Energy saving
Standby
OFF
Printing
- Scanner heater
- PCDU heater
- Main machine tray heater
- Optional paper feed tray heater
ON(1)
ON ON
ON
OFF
1201
1202
7. Detailed Descriptions
Imaging system (front)
Imaging system (rear)
Exterior Cover/ Air Flows (Fan Control)
1203
7. Detailed Descriptions
Electric system
1204
4
5
6
7
No.
1
3
8
9
Development intake fan
Paper exit cooling fan
Fusing exhaust fan
Deodorization filter
Ozone exhaust fan
Toner supply cooling fan
Ozone filter/Dust filter
Controller box cooling fan
Part name
Exterior Cover/ Air Flows (Fan Control)
No.
10 PSU cooling fan
Part name
By installing the duct corresponding to each fan, the air flow is efficiently controlled to a cooling target.
Moreover, improvement in quietness and energy-saving efficiency is achieved by performing stepwise operation of the fan according to the imaging temperature.
Air taken in by the PSU cooling fan is guided near the cooling target by the duct, and is efficiently cooled.
Air taken in with the toner supply cooling fan is guided to circulate around the toner bottle, and is discharged from the side of the delivery tray to outside the machine. It is aimed to achieve heat insulation from the stack of paper to the toner bottle by reducing the melting point of the toner.
By discharging air taken in from the development intake fan at the front, from the ozone exhaust fan at the rear, a uniform air flow is attained and efficient cooling is realized. Discharge of ozone and scattering of toner are prevented by installing an ozone filter and a dust filter in front of the ozone exhaust fan.
Air taken in from the paper discharge cooling fan at the front is discharged from the fusing heat discharge fan at the rear to outside the machine. By cooling the paper immediately after fusing, not only cooling of the fusing exit sensor but also reduction of stored heat of the stacked paper and reduction of curl are realized. This also serves to prevent condensation on the paper discharge guide sheet. As a measure against odor, a deodorization filter is installed downstream from the fusing exhaust fan.
Air is circulated by the controller box cooling fan installed in the controller box, preventing temperature rise in the controller box.
1205
7. Detailed Descriptions
In order to suppress excessive temperature rise in the machine and maintain equipment quality, a temperature sensor (imaging temperature sensor (thermistor)) [A] is installed in the machine. The imaging temperature sensor (thermistor) detects the temperature environment in the machine, and controls cooling operation.
1206
Overview of cooling operation in the machine
The temperature in the machine is detected during output and after output, and the interior of the machine is cooled by fan operation (stepwise operation of fan, prolonged fan rotation after paper has passed through) according to the temperature inside the machine.
However, if the temperature inside the machine rises significantly due to passing a large volume of paper, in addition to fan operation, the CPM is specified to control the temperature in the machine.
Cooling operation during output
Perform cooling operation under the following conditions.
Imaging temperature
Fusing exhaust fan
Ozone exhaust fan
Toner supply cooling fan
Development intake fan
*3
PSU cooling fan
*2
Less than
34
ON
20%
-
-
ON
34
ON
20%
-
-
35
ON
30%
-
-
36
ON
30%
ON
ON
37
ON
40%
ON
ON
38
ON
40%
ON
ON
40
*1
ON
40%
ON
ON
ON ON ON ON ON ON
The operation start temperature can be modified by SP.
Exterior Cover/ Air Flows (Fan Control)
• *1 If the imaging temperature reaches 41°C each fan will continue operating until it falls by
2°C.
• *2 Operating condition:
When the time interval from the previous job is less than 10 minutes. Or, when the time interval from the previous job is more than 10 minutes, and 5 minutes have elapsed from start of machine.
• *3 Operating condition:
For 36°C or above, full speed rotation at 24V
For less than 36°C, rotated at low speed with voltage reduced to 13V (rotating speed approximately 50%)
Changes from low speed rotation to full speed rotation when printing continues for more than
5 minutes while the temperature inside the machine is 36°C or lower
Cooling operation after output
Usually, after output, fan operation is suspended.
If the temperature in the machine after output is high, fan rotation is continued after output to cool the interior of the machine.
The Helmholtz silencer applies the resonance phenomenon called the "Helmholtz resonance" to emit a sound having reverse phase of the motor frequency by resonance and cancel the motor noise.
On this machine, it is located on the controller box side to reduce the noise. The BCU [B] is mounted on the mold [A] of the Helmholtz silencer.
1207
1208
7. Detailed Descriptions
Energy Save
Customers should use energy saver modes properly, to save energy and protect the environment.
The area shaded grey in this diagram represents the amount of energy that is saved when the timers are at the default settings. If the timers are changed, then the energy saved will be different. For example, if the timers are all set to 60 min., the grey area will disappear, and no energy is saved before 60 min.
expires.
The user can set these timers with User Tools (Machine Features > System Settings > Timer Settings)
Sleep Mode Timer
User Tools (Machine Features > System Settings > Timer Settings)
After a specified period has passed, or [Energy Saver] is pressed, the machine enters Sleep mode in order to conserve energy. Specify the time to elapse before Sleep mode.
Default: [1 minute(s)]
Sleep mode timer may not work when error messages appear.
1209
1210
7. Detailed Descriptions
Depending on which embedded software architecture application is installed on it, the machine might take longer than indicated to enter Sleep mode.
Fusing Unit Off Mode (Energy Saving) On/Off
User Tools (Machine Features > System Settings > Timer Settings)
Specifies whether Fusing Unit Off mode is enabled or not.
When Fusing Unit Off mode is enabled, the display is on but the fusing unit is off to save energy.
The machine requires roughly the same time as warm-up time to recover from Fusing Unit Off mode.
Default: [Off]
If [Fusing Unit Off Mode (Energy Saving) On/Off] is set to [On], you can specify when to exit
Fusing Unit Off mode and the time to elapse before entering Fusing Unit Off mode.
If [Exit Fusing Unit Off Mode] is set to [On Printing], the machine exits Fusing Unit Off mode when printing is performed.
If [Exit Fusing Unit Off Mode] is set to [On Operating Control Panel], the machine exits Fusing Unit
Off mode when a key other than the copy function key is pressed on the control panel of the machine.
If printing is performed with the copy function or a key in the copy function is pressed on the control panel of the machine, the machine exits Fusing Unit Off mode regardless of this setting. If the timer is set to [On], you can set the time from 10 seconds to 240 minutes, using the number keys.
Energy Saving Recvry. for Business Application.
User Tools (Machine Features > System settings > General Settings)
Specify whether or not to enable low-energy recovery from Sleep mode to use applications independent of the machine, such as Address Book Management or Browser.
Default: [Off]
If [On (Energy Saving)] is selected, it takes longer than usual to be ready to use the machine.
Reduced electrical consumption in Sleep mode:
MP C2004
NA: 0.85 W
EU: 1.00 W
MP C2504
NA: 0.85 W
EU: 1.00 W
Recovery time from Sleep mode
MP C2004
6.0 sec.
MP C2504
6.0 sec.
Energy Save
1211
1212
7. Detailed Descriptions
Energy Save
State
1
Standby/Printing
2 Printing state/
Panel OFF
3 Fusing OFF
Description
• State where normal operation is possible after warm-up
• State during printing
State when printing with the backlight of the operation panel turned off
4 Quiet state
5 Engine OFF
(Sleep mode)
6 STR state
(Sleep mode)
7 Pre-recovery
State where the Standby Fusing OFF state is entered when the time set with the "Fusing Unit Off Mode (Energy Saving) On/Off" setting of the User
Tools has elapsed.
• State where the operation panel is flashing and the fusing lamp is OFF.
• The bottom plate of the paper feed tray is raised.
Quiet state is entered when the Energy Saving key is pressed or the time set with the "Sleep Mode Timer" of the User Tools has elapsed. This is a temporary energy saving state before entering sleep mode.
• Basically, no homing (initialization) of peripheral devices is performed.
• The bottom plate of the paper feed tray is raised.
• The fusing lamp is turned OFF.
Entered from Quiet state with internal timer.
• The relevant power systems (24V, 12V, 5V) are turned OFF at the same time as the fusing lamp.
• When receiving a fax or printing is performed in engine OFF state, warm-up is started and printing is performed while the backlight of the operation panel is turned OFF.
Supplying of power and clock to the CPU and peripheral chips on the controller board is stopped.
The Pre-recovery state is entered from STR state when the proximity sensor
(human detection sensor) detects presence of a person.
This is the Energy Saving state where the power of the operation panel and
HDD is ON and the power of the engine is OFF, but the backlight of the operation panel LCD is off.
Device state for each Energy Saving state
1213
1214
7. Detailed Descriptions
Standby/Printing
Printing state/Panel
OFF fusing OFF
Quiet state
Engine OFF
STR state
State
Pre-recovery
Energy Saving
LED
ON
ON
Operation panel
LCD
ON
OFF
ON
ON
ON
OFF
ON*1
Sleep
OFF or ON*1
Engine
(Printer/Scanner)
ON
ON
(Only scanner is in
Quiet state)
ON
(Both printer/ scanner are in
Quiet state)
ON
(Both printer/ scanner are in
Quiet state)
OFF Blinking gradually
ON*1
Blinking gradually
ON
Sleep
OFF
ON*1
OFF
OFF
HDD CTL
ON ON
ON ON
ON ON
ON ON
OFF
ON*
1
ON
OFF STR
ON ON
*1 When [Energy Saving Recvry. for Business Applicatn.] is [On (Energy Saving)], ON/OFF is determined by the internal timer of the Smart Operation Panel.
Transition of operation panel to Energy Saving when [Energy Saving Recvry. for Business
Applicatn.] is [On (Energy Saving)]
Normally, the Energy Saving state of the operation panel LCD changes in step with the energy saving state of the MFP/LP main unit, but to support the scenario where an application that does not use the engine (printer/scanner) is executed from the operation panel, the Energy Saving state of the operation panel is transitioned through the three states ON, OFF, and Sleep with its internal timer when [Energy Saving Recvry. for Business Applicatn.] is [On (Energy Saving)].
Energy Save
The up time for each power state of the machine can be checked with SP8-961 (Electricity Status). It is also output on the SMC sheet.
SP
SP8-961-001
Name
Ctrl Standby Time
SP8-961-002
SP8-961-003
STR Time
Main Power Off Time
Cumulative time of STR mode
Cumulative time of state in which the power plug is connected to the outlet but the main power is off
SP8-961-004 Reading and Printing Time Cumulative time of state in which both the plotter engine and scanner engine are running or warming up
SP8-961-005 Printing Time
SP8-961-006 Reading Time
Cumulative time of the state in which the plotter engine is running
Cumulative time of the state in which the scanner engine is running
SP8-961-007 Eng Waiting Time
Description
Cumulative time of Engine OFF mode, Quiet mode, and Standby mode
SP8-961-008
SP8-961-009
SP8-961-010
SP8-961-011
Low Power State Time
Quiet State Time
Heater Off State Time
LCD on Time
Cumulative time of state in which the power state of the engine is Standby state
Not used for this machine
Cumulative time of the state in which the power state of the engine is Quiet state
Cumulative time of the state in which the power state of the engine is fusing OFF state
Cumulative time of the state in which the backlight of the LCD is on.
SP8-941 (Machine Status) keeps a record of the amount of time that the machine spends in each mode.
1215
1216
7. Detailed Descriptions
SP
SP8-941-001
SP8-941-002
SP8-941-003
SP8-941-004
SP8-941-005
SP8-941-006 to 009
Name
Operation Time
Standby Time
Low Power Time
Sleep mode time
Off Mode Time
Down time
Description
Cumulative time of the state in which the engine state notification is enabled.
The state in which the engine is not running (such as when storing to HD only with the controller) is excluded from the running state.
Cumulative time of the state in which the engine state is not running.
Not used for this machine
Cumulative time in Sleep Mode state.
Cumulative time in which the Energy Saving state of the device is engine OFF state.
Cumulative time in which the device is disabled because itself or its component is in the following state.
• SP8-941-006: SC (excluding mode SC)
• SP8-941-007: Jam (plotter)
• SP8-941-008: Jam (scanner)
• SP8-941-009: Supply/PM unit end
With this data, and the power consumption values from the specifications, we can estimate the amount of energy that is used by the machine.
This should only be used as a reference value, because the power consumption specifications are measured in a controlled environment with a constant power supply.
To get an exact measurement at the customer’s site, a watt meter must be used to measure the actual energy consumed.
To use SP8-941 to calculate the energy consumed:
• At the start of the measurement period, read the values of SP8-941-001 to 005.
• At the end of the measurement period, read the values of SP8-941-001 to 005 again.
• Find the amount of time spent in each mode (subtract the earlier measurement from the later measurement).
• Multiply this by the power consumption spec for each mode.
• Convert the result to kWh (kilowatt hours)
Energy Save
We recommend that the default settings related to energy saving should be kept.
• If the customer requests that these settings should be changed, please explain that their energy costs could increase, and that they should consider the effects on the environment of extra energy use.
1217
1218
7. Detailed Descriptions
The proximity sensor (human detection sensor) is located on the right upper corner of the main machine.
When the machine has been idle for a long period and the proximity sensor (human detection sensor) detects the presence of anyone in front of the machine, it signals the machine to prepare itself for quick recovery to operation status by shortening the time required for the machine to recover full operation
(pre-recovery mode) before the operator even touches the machine or operation panel. The proximity sensor (human detection sensor) employs infrared and can detect the presence of the operator within an arc of 150° out to 1.8 m (6 ft.) away from the front of the machine.
Proximity Sensor (Human Detection Sensor)
There are three phases in the operation of the proximity sensor (human detection sensor):
• First, the sensor detects the presence of the operator within the arc in front of the machine, and then signals the machine to leave the STR mode (or Engine OFF mode) and enter the Pre-recovery mode.
• Second, as soon as the machine enters the Pre-recovery mode it resets the Engine Off mode timer for 5 min. If the operator does not touch the machine for 5 minutes, the machine slips back into the
Engine Off mode. If the operator touches the LCD, or opens and closes the ADF or front cover, etc., the machine shifts to Standby mode.
• Third, once the machine enters Standby mode, if the operator does nothing to start operation, the machine will gradually step down from Standby mode to Lower Energy mode, Quiet mode, Engine
Off mode, and then finally to STR mode.
Here are more details about these operation mode levels.
• STR mode. Suspend-to-RAM mode. The power supply to the CPU, adjacent chips, and the clock on the controller board is shut down.
• Engine Off mode. The fusing lamps and other engine components remain off. The operation panel backlight is off, but there is power supplied to the operation panel and the controller boards.
• Pre-recovery mode. The operation panel and HDD are on but the engine components remain off
(Energy Save mode). However, the operation backlight still remains off, so there is no change on
1219
1220
7. Detailed Descriptions the operation panel to indicate that the machine has shifted from STR mode, through Engine Off mode, and into Pre-recovery mode.
• Quiet mode. Fusing lamps still remain off, but the HDD and SD cards are accessible so the machine can receive jobs (Data In) and incoming faxes.
• Lower Power mode. Finally, power is restored to the fusing lamps but maintained at low temperature.
• Standby mode. The machine is ready to operate.
The operation of the proximity sensor (human detection sensor) can be switched off and on with a User
Tool setting.
1. Press "User Tools" on the operation panel.
2. Select Machine features > System Settings > General Settings > Human Detection Sensor
3. You can switch the sensor off/on by selected Disabled/Enabled. The default setting is "Enabled".
One of two SC codes is issued if the proximity sensor (human detection sensor) fails.
SC869-01 Proximity sensor (human detection sensor) failure: Error 1
The sensor remained on for over 24 hours.
• Cycling the machine off/on does not cancel this error.
• When this error occurs the machine enters sensor failure mode and ignores subsequent input from the proximity sensor (human detection sensor).
• Even though the sensor is on, the machine does not enter Pre-recovery mode, and the Engine Off timer setting is not affected and continues to operate normally.
• To cancel the error, switch off the proximity sensor (human detection sensor) with the User Tool setting described above.
• The sensor and its components require replacement.
SC869-02 Proximity sensor (human detection sensor) failure: Error 2
The sensor remained off, even after the operator performed 20 actions with the machine operation panel, opening and closing the front cover, ADF, etc. The machine will issue this error code after every
20 events in operation of the machine.
• Cycling the machine off/on does not cancel this error.
• To cancel the error, switch off the proximity sensor (human detection sensor) with the User Tool setting described above.
Proximity Sensor (Human Detection Sensor)
• The sensor and its components require replacement.
There is one proximity sensor (human detection sensor) related SP code: SP5102-203 Auto Detect: human detection check. This is an on/off check.
• Enter "0" to switch the sensor off.
• Enter "1" to switch the sensor on.
This SP is used to check the operation of the sensor. It confirms that the sensor can be switched off and on normally. (Default: On). This check can be used regardless of the User Tool setting. Even if the sensor is switched off with the User Tool setting, a check can be done with this SP code.
1221
1222
MEMO
MEMO
1223
MEMO
1224
EN
MP C2004 / C2504
Machine Code:
D243 / D244
July, 2016
This manual uses several symbols and abbreviations. The meaning of those symbols and abbreviations are as follows:
Abbreviations
SEF
LEF
K
C
M
Y
B/W, BW
FC
Short Edge Feed [A]
Long Edge Feed [B]
Black
Cyan
Magenta
Yellow
Black and White
Full color
What it means
Adobe, Acrobat, PageMaker, PostScript, and PostScript 3 are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Ricoh Company, Ltd. is under license.
Firefox and Thunderbird are registered trademarks of the Mozilla Foundation.
Google, Android, and Chrome are trademarks of Google Inc.
1
iOS® is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the United
States and certain other countries.
Java is a registered trademark of Oracle and/or its affiliates.
JAWS® is a registered trademark of Freedom Scientific, Inc., St. Petersburg, Florida and/or other countries.
Kerberos is a trademark of the Massachusetts Institute of Technology (MIT).
Linux is a registered trademark of Linus Torvalds.
Macintosh, OS X, Bonjour, Safari, and TrueType are trademarks of Apple Inc., registered in the U.S.
and other countries.
Microsoft, Windows, Windows Server, Windows Vista, Internet Explorer, and Outlook are either registered trademarks or trademarks of Microsoft Corp. in the United States and/or other countries.
PictBridge is a trademark.
QR Code is a registered trademark of DENSO WAVE INCORPORATED in Japan and in other countries.
"Red Hat" is a registered trademark of Red Hat, Inc.
The SD and SD logo are trademarks of SD-3C, LLC.
UNIX is a registered trademark of The Open Group.
UPnP is a trademark of UPnP Implementers Corporation.
2
This product includes RSA BSAFE® Cryptographic software of EMC Corporation. RSA and BSAFE are registered trademarks or trademarks of EMC Corporation in the United States and other countries.
The proper names of Internet Explorer 6, 7, and 8 are as follows:
• Microsoft® Internet Explorer® 6
• Windows® Internet Explorer® 7
• Windows® Internet Explorer® 8
The proper names of the Windows operating systems are as follows:
• The product names of Windows Vista are as follows:
Microsoft® Windows Vista® Ultimate
Microsoft® Windows Vista® Business
Microsoft® Windows Vista® Home Premium
Microsoft® Windows Vista® Home Basic
Microsoft® Windows Vista® Enterprise
• The product names of Windows 7 are as follows:
Microsoft® Windows® 7 Home Premium
Microsoft® Windows® 7 Professional
Microsoft® Windows® 7 Ultimate
Microsoft® Windows® 7 Enterprise
• The product names of Windows 8 are as follows:
Microsoft® Windows® 8
Microsoft® Windows® 8 Pro
Microsoft® Windows® 8 Enterprise
• The product names of Windows 8.1 are as follows:
Microsoft® Windows® 8.1
Microsoft® Windows® 8.1 Pro
Microsoft® Windows® 8.1 Enterprise
• The product names of Windows 10 are as follows:
Microsoft® Windows® 10 Home Premium
Microsoft® Windows® 10 Pro
Microsoft® Windows® 10 Enterprise
Microsoft® Windows® 10 Education
• The product names of Windows Server 2003 are as follows:
Microsoft® Windows Server® 2003 Standard Edition
Microsoft® Windows Server® 2003 Enterprise Edition
• The product names of Windows Server 2003 R2 are as follows:
Microsoft® Windows Server® 2003 R2 Standard Edition
Microsoft® Windows Server® 2003 R2 Enterprise Edition
• The product names of Windows Server 2008 are as follows:
Microsoft® Windows Server® 2008 Standard
Microsoft® Windows Server® 2008 Enterprise
• The product names of Windows Server 2008 R2 are as follows:
Microsoft® Windows Server® 2008 R2 Standard
Microsoft® Windows Server® 2008 R2 Enterprise
3
4
• The product names of Windows Server 2012 are as follows:
Microsoft® Windows Server® 2012 Foundation
Microsoft® Windows Server® 2012 Essentials
Microsoft® Windows Server® 2012 Standard
• The product names of Windows Server 2012 R2 are as follows:
Microsoft® Windows Server® 2012 R2 Foundation
Microsoft® Windows Server® 2012 R2 Essentials
Microsoft® Windows Server® 2012 R2 Standard
Other product names used herein are for identification purposes only and might be trademarks of their respective companies. We disclaim any and all rights to those marks.
Microsoft product screen shots reprinted with permission from Microsoft Corporation.
5
6
7
8
Item
Configuration:
CPU:
RAM:
Color Support:
Photoconductor Type:
Copy System:
Develop System:
Fusing System:
Desk top
Specification
Intel Atom Processor Bay Trail 1.33GHz
2GB
Full color
OPC drum
Laser beam scanning and electro-photographic printing
First copy time*1:
Copy Speed (A4/LT: LEF):
Dry two-component magnetic brush development system
Direct heating (DH) fusing
Black & White: 5.5 sec.
Color: 7.7 sec.
MP C2004:
Color 20 sheets/min., Black & White 20 sheets/min.
MP C2504:
Color 25 sheets/min., Black & White 25 sheets/min.
Warm-Up-Time:
(Normal Temperature 20C/68F,
NRP)
Originals:
26 sec.
Sheet/Book
Maximum original size:
A3 SEF (297 x 420mm), 11 x 17 SEF (279 x 432mm): A3/DLT full size
9
1. Specifications
RTB 28
Modified
RTB 33
New item
Paper Size:
Item
Paper Thickness:
Mask image area:
Copy Scale (Zoom):
Resolution (Scanning):
Resolution(Writing):
Gradation:
Feeding System / Paper
Capacity:
Continuous Copy:
Power Source:
Power consumption:
Dimensions (W x D x H):
Specification
Main unit upper tray (1 st
tray): A4 LEF/LT LEF
Main unit lower tray (2 nd
tray): 12.6"x17.7"/12"x18" to A6 SEF
Bypass tray: 12.6"x17.7"/12"x18"/320x457mm to A6 SEF
Custom size Width: 90 to 320 mm
(Bypass) Length: 148 to 600 mm
• Tray 1: 60 to 300 g/m
2
• Tray 2: 60 to 300 g/m
2
• Bypass tray: 52 to 300 g/m
2
• Duplex: 52 to 169 g/m
2
• Leading edge: 4.2 ± 1.5 mm (0.17 ± 0.06”)
• Left/Right: 0.5 to 4.0 mm (0.02 to 0.16”)
• Trailing edge: 0.5 to 6.0 mm (0.02 to 0.24”)
25 to 400% (1% steps)
600 dpi x 600 dpi
600 dpi x 600 dpi
256
• 550 x 2 + 550 x 2 + 100 sheets (4 drawers paper feed model)
1 to 999 Sheets
NA: 120-127V, 60Hz
EU, AA, CHN, KOR: 220-240V, 50/60Hz
TWN: 110V, 60Hz
1.85 kW or less
• 587 x 685 x 788 mm (23.1 x 27.0 x 31.0 inches)
(Main Unit)
• 587 x 685 x 913 mm (23.1 x 27.0 x 35.9 inches)
(Equipped with the ARDF)
• 587 x 685 x 968 mm (23.1 x 27.0 x 38.1 inches)
(Equipped with the SPDF)
10
Machine Specifications
RTB 28
Modified
Weight:
Item
Unit Occupation Dimensions (W x D):
Specification
Main Unit: 1,149 x 1,236 mm (45.2 x 48.7 inches)
(With the bypass table opened, the bypass extension tray opened, the right door opened, and the paper tray pulled)
Approx. 83.3 kg (183.6 lb.)
*1 A4 LEF, 1 st
paper feed tray, with book scanner.
Item
Print Size:
Print Speed (A4/LT: LEF):
Resolution:
PDL:
Specification
Fixed size:
Max. A3 SEF (297 x 420 mm), 12 x 18 SEF (304.8 x 457.2 mm)
Custom:
Max. 320 x 600 mm (bypass tray)
• MP C2004:
Color 20 sheets/min., Black & White 20 sheets/min.
• MP C2504:
Color 25 sheets/min., Black & White 25 sheets/min.
1200 x 1200 dpi, 600 x 600 dpi, 400 x 400 dpi, 300 x 300 dpi, 200 x 200 dpi
• Standard:
PDF Direct, MediaPrint: JPEG, MediaPrint: TIFF
• Optional:
PS3, IPDS, PictBridge
11
12
1. Specifications
Interface:
Protocol:
Built-in Fonts:
Scale:
Item
USB Interface (Standard):
Specification
• Standard:
USB2.0 Type A
SD Slot
Ethernet (1000BASE-T/100BASE-TX/10BASE-T)
• Optional:
Wireless LAN (IEEE802.11a/b/g/n)
IEEE1284
Gigabit Ethernet (Optional for EFI)
Bluetooth Ver2.0+EDR
• Standard:
TCP/IP (IPv4/IPv6), SMB, IPP, FTP, bonjour, RSH, LPD,
DIPRINT, NetBIOS, WSD (Device/Printer/Scanner), UDP,
ICMP, SSL, TSL, IPsec, HTTP, SMTP, POP3, IMAP4, SNMP v1/v2/v3, DNS, Dynamic DNS, LDAP, DHCP, RCP, SNTP,
IEEE802.1X, HTTPS, RHPP, NTLM, Kerberos, LLTD, TELNET,
WINS, sftp, ssh, SSDP (UpnP)
• Available Operating Systems:
Windows 2000/XP/Vista/7/8/8.1/10, Windows Server
2003/2003 R2/2008/2008 R2/2012/2012 R2, Mac
OS 10.7 or later.
• Communication mode:
Corresponding to USB2.0 Standard
• Connecting mode:
Devices corresponding to USB2.0 Standard
• PCL 5c/6: 45 fonts + International fonts 13 fonts
• PDF: 136 fonts
• PS 3: 136 fonts
• IPDS: 108 fonts (Option)
25% to 400%
Machine Specifications
Item
Originals:
Available Original Size for
Scanning:
Auto Detectable Size for
Originals Set to Book scanner:
Auto Detectable Size for
Originals Set to ADF:
Original Scanning Speed
(A4/LT: LEF):
Gradation:
Basic Scanning Resolution:
Specification
Sheet, Book, Object
Minimum length: 10 mm, Maximum length: 432 mm
Minimum width: 10 mm, Maximum width: 297 mm
A3 SEF, B4 JIS SEF, A4 SEF/LEF, B5 JIS SEF/LEF, A5 SEF/LEF,
11 x 17SEF, 8
1
/
2
” x 14”SEF, 8 1/2 x 13 2/5 SEF, 8
11” SEF/LEF, 5 1/2 x 8 1/2 SEF/LEF
1
/
2
” x
A3 SEF, B4 JIS SEF, A4 SEF/LEF, B5 JIS SEF/LEF, A5 SEF/LEF,
B6 JIS SEF/LEF, 11 x 17SEF, 8
SEF, 8
1
1
/
2
” x 14”SEF, 8 1/2 x 13 2/5
/
2
” x 11” SEF/LEF, 7 1/4 x 10 1/2 SEF/LEF, 5 1/2 x 8
1/2 SEF/LEF, 10 x 14 SEF
When using E-mail, Scan to Folder, WSD (Push Type), or Scan to
Removable device (Original size: A4 LEF, Resolution: 200 dpi/300 dpi), Original scanning speed will be as following:
Black & White:
• ARDF DF3090: 80 sheets/min (Simplex)
• SPDF DF3100: 110 sheets/min (Simplex), 180 sheets/min
(Duplex)
(Original Type: B & W: Text/ Line Art, Compression (Black &
White): MMR, ITU-T No1 Chart)
Color:
• ARDF DF3090: 80 sheets/min (Simplex)
• SPDF DF3100: 110 sheets/min (Simplex), 180 sheets/min
(Duplex)
(Original type: Full Color: Text/ Photo, Compression (Gray
Scale/ Full Color): Default, Original chart)
Depending on: machine operating conditions, PC use environment, scanning conditions, original content, the scan speed might change.
Black & White: 2
Color/Gray scale: 256
200 dpi
13
14
1. Specifications
Item
Compress Format for Binary
B&W Image:
Compress Format for Gray
Scale / Full Color:
MH/MR/MMR/JBIG2
JPEG
Specification
Interface:
• Ethernet (1000BASE-T/100BASE-TX/10BASE-T)
• Wireless LAN (IEEE802.11a/b/g/n)
• USB2.0 Type A
• SD Card Slot
Protocol for Network
Connection:
Scanning Resolution for Sending email:
Available Protocol for Sending email:
Output Format for Sending email*1:
Scanning Resolution for Scan to
Folder:
Available Protocol for Send to
Folder:
Output Format for Send to
Folder*1:
Available Protocol for WSD
Scanner Sending:
Scan Resolution for Network
TWAIN Scanner:
Available Protocol for Network
TWAIN Scanner:
TCP/IP
100dpi, 200dpi, 300dpi, 400dpi, 600 dpi
POP, SMTP, IMAP4
TIFF, JPEG, PDF, High Compression PDF, Searchable PDF, PDF/A
100 dpi, 200 dpi, 300 dpi, 400 dpi, 600 dpi
SMB, FTP
TIFF, JPEG, PDF, High Compression PDF, Searchable PDF, PDF/A
Web Services on Devices for Scanning
100 to 1200 dpi
TCP/IP
Machine Specifications
Item
Available Operating Systems for
Network TWAIN Scanner:
Specification
Windows Vista/7/8/8.1/10, Windows Server
2003/2008/2008 R2/2012/2012 R2
(TWAIN scanner runs in 32-bit compatible mode on a 64-bit operating system, so TWAIN scanner is not compatible with 64bit applications. Use it with 32-bit applications.)
Scanning Resolution for Scan to
Network (Main Scan x Sub
Scan):
Scan Resolution for when Using
WIA Scanner (main Scan x Sub
Scan):
Available Protocol for when
Using WIA Scanner:
100 dpi, 200 dpi, 300 dpi, 400 dpi, 600 dpi
100 to 1200dpi
TCP/IP
Available Operating Systems for
WIA Scanner:
Windows Vista (SP1 or later) /7/8/8.1/10, Windows Server
2008 /2008 R2
(WIA scanner can function under both 32- and 64-bit operating systems.)
Item
Capacity for Document Server:
Document Server Manageable
File numbers:
Spec.
Approx. 73 GB
Max. Pages per file: 2,000 pages
Max.: 9,000 Pages (Storable pages of all storage)
Stored File retention period: 1 to 180 days, or unlimited
Max. Folders: 200
Max. 3,000 files
15
16
1. Specifications
Item
Memory Sortable Pages:
Spec.
Max. 2,000 pages
Copy/ B&W/ A4 original: Appox. 2,000 pages
Printer/ B&W/ A4/ When 600 dpi 2bit: Approx. 2,000 pages
(With printer sort, depends on printing image)
Copy Speed: Simplex (Standard Mode, A4 / LT LEF)
MP C2004 MP C2504
BW: 20 cpm
FC: 20 cpm
BW: 25 cpm
FC: 25 cpm
ARDF 1 to 1 Speed: Single Sided Original (Standard Mode, A4 / LT LEF)
MP C2004 MP C2504
BW: 20 cpm
FC: 20 cpm
BW: 25 cpm
FC: 25 cpm
Copy Speed: Duplex (Standard Mode, A4 / LT LEF)
MP C2004 MP C2504
BW: 20 cpm
FC: 20 cpm
BW: 25 cpm
FC: 25 cpm
ARDF 1 to 1 Speed: Double Sided Original (Standard Mode, A4 / LT LEF)
MP C2004 MP C2504
BW: 20 cpm
FC: 20 cpm
BW: 25 cpm
FC: 25 cpm
Electric Sort Copy Speed: Duplex Single sided to Double Sided (A4 / LT
LEF)
MP C2004 MP C2504
BW: 20 cpm
FC: 20 cpm
BW: 25 cpm
FC: 25 cpm
Machine Specifications
Item
Off/ Sleep mode shift time:
System all reset time:
Spec.
Standard: 1 min., With initial setting 1 to 60 min. (1 min. per step)
Standard: 60 sec., 10 to 999 Sec. (1 sec. per step), or “Do not clear” can be selected.
Item
Off / Sleep mode:
Watts
NA: 0.85 W or less
EU: 1.00 W or less
6.0 sec.
Recovering time
• Depending on operating environment and usage status, power consumption in OFF/Sleep mode might change.
(Such cases as power change for fusing unit temperature control when in a low temperature environment, or network environment obstructs switching to STR mode.)
Running:
Models
Mainframe only:
Full system:
Standby:
Models
Mainframe / Full system
MP C2004
58.4 dB
67.5 dB
MP C2004
35.0 dB
MP C2504
58.7 dB
67.5 dB
MP C2504
35.0 dB
17
18
1. Specifications
The printer drivers and utility software are provided on one CD-ROM. An auto-run installer allows you to select which components to install.
Operating System
*1
Windows Vista
*2
Windows 7
*3
Windows 8
*4
Windows 8.1
*5
Windows 10
*6
Windows Server 2003
*7
Windows Server 2008
*8
Windows Server 2012
*9
OS X
*10
PCL 5c
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Not available
Printer Language
PCL 6
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Not available
*1 Windows operating system supports both versions (32/64 bit).
*2 Microsoft Windows Vista Ultimate/Microsoft Windows Vista Enterprise/Microsoft Windows Vista Business/
Microsoft Windows Vista Home Premium/Microsoft Windows Vista Home Basic
*3 Microsoft Windows 7 Home Premium/Microsoft Windows 7 Professional/Microsoft Windows 7 Ultimate/
Microsoft Windows 7 Enterprise
*4 Microsoft Windows 8/Microsoft Windows 8 Pro/Microsoft Windows 8 Enterprise
*5 Microsoft Windows 8.1/Microsoft Windows 8.1 Pro/Microsoft Windows 8.1 Enterprise
*6 Microsoft Windows 10 Home/Microsoft Windows 10 Pro/Microsoft Windows 10 Enterprise/Microsoft
Windows 10 Education
*7 Microsoft Windows Server 2003 Standard Edition/Microsoft Windows Server 2003 Enterprise Edition/
Microsoft Windows Server 2003 R2 Standard Edition/Microsoft Windows Server 2003 R2 Enterprise
Edition
*8 Microsoft Windows Server 2008 Standard/Microsoft Windows Server 2008 Enterprise/Microsoft
Windows Server 2008 R2 Standard/Microsoft Windows Server 2008 R2 Enterprise
PostScript 3
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Software Accessories
*9 Microsoft Windows Server 2012 Foundation/Microsoft Windows Server 2012 Essentials/Microsoft
Windows Server 2012 Standard/Microsoft Windows Server 2012 R2 Foundation/Microsoft Windows
Server 2012 R2 Essentials/Microsoft Windows Server 2012 R2 Standard
*10 OS X 10.7 or later
• Some applications may require installation of the PCL 5c printer driver. In this case, you can install
PCL 5c without having to install PCL 6.
• Adobe PostScript printer driver allows the computer to communicate with the printer using a printer language. PPD files allow the printer driver to enable specific printer functions.
Operating System
Windows Vista
Windows 7
Windows 8
Windows 8.1
Windows 10
Windows Server 2003/2003 R2
Windows Server 2008/2008 R2
Windows Server 2012/2012 R2
OS X
TWAIN
*1
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Not available
PC-FAX
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Not available
*1 TWAIN scanner runs on a 64-bit operating system, but is not compatible with 64-bit applications. Use it with
32-bit applications.
19
20
1. Specifications
NA
Size (W x L) [mm]
A3 SEF (297 x 420)
B4 SEF (257 x 364)
A4 SEF (210 x 297)
A4 LEF (297 x 210)
B5 SEF (182 x 257)
B5 LEF (257 x 182)
A5 SEF (148 x 210)
A5 LEF (210 x 148)
B6 SEF (128 x 182)
B6 LEF (182 x 128)
DLT SEF (11" x 17")
LG SEF (8
1
/
2
" x 14")
LT SEF (8
1
/
2
" x 11")
LT LEF (11" x 8
1
/
2
")
HLT SEF (5
1
/
2
" x 8
1
/
2
")
HLT LEF (8
1
/
2
" x 5
1
/
2
")
F SEF (8" x 13")
Foolscap SEF (8
13")
1
/
2
" x
Folio SEF (8
1
/
4
" x 13")
Folio SEF (11" x 15") -
-
-
Book
-
-
Y
*5
Y
*5
-
-
-
-
-
-
Y
Y
Y
*5
Y
*5
Y
*2
Y
-
-
-
-
Y
*Db
Y
*Dc
Y
*Dd
Y
*De
Y
Y
-
Y
-
-
-
ADF
Y
-
Y
Y
*Sc
-
Y
*Sb
-
Y
*5
Y
*5
-
-
-
-
Y
*S3
Y
*4
Y
*4
Y
*2, 4
Y
*4
Book
Y
*4
Y
*4
Y
*4, 5
Y
*4, 5
-
Y
*D3
Y
*S3
-
EU/AP
Y
*D3
Y
*S3
-
Y
Y
Y
Y
ADF
Y
Y
Y
Y
Y
Y
Y
*Df
-
Y
*Di
Y
*Dg
-
-
Y
*S3
Supported Paper Sizes
Size (W x L) [mm]
Folio SEF (10" x 14")
Folio SEF (8" x 10")
US EXE SEF (7
10
1
/
2
")
1
/
4
" x
US EXE LEF (10
1
/
2
x
7
1
/
4
")
8K SEF (267 x 390)
16K SEF (195 x 267)
16K LEF (267 x 195)
Book
-
-
-
-
-
-
-
NA
ADF
Y
*Sd
Y
Y
Y
*Se
-
-
-
Book
-
-
-
-
Y
*4
Y
*4
Y
*4v
EU/AP
ADF
-
-
-
-
Y
*Sf
Y
*Si
Y
*Sg
Sizes with letters (a, b, c) means only either size with the corresponding letter can be selected for size detection. “D” is for default set sizes, and when setting “S” sizes for size detection from SP mode, “D” sizes can no longer be detected.
(*2)For detected originals smaller then A5 size, with SP mode either “detect as A5” or “Detect as
Unknown” can be selected. (Default is “Detect as unknown”)
(*3)F Sizes (8.5” x 13” SEF, 8.25” x 13” SEF, 8” x 13” SEF) will be available by SP mode settings.
(*4)Switch Book scanner original detection between “K” series and ”A/B” series from SP mode.
(Can not set both to detect, but 8K/16K detect can de set from SO mode)
8K SEF -> Switch between A3, B4 SEF
16K SEF -> Switch between A4, A5, B5 SEF
16K LEF -> Switch between A4, A5, B5 LEF *Can not switch only either size.
(*5)Can be selected with switching A4/LT from SP mode:
• Standard detect (default)
• When placing A4/LT size LEF, detect as A4 LEF. When placing SEF, detect as LT SEF.
• When placing A4/LT size LEF, detect as LT LEF. When placing SEF, detect as A4 SEF.
Remarks:
Y
-
Yes; available
Not available
21
22
1. Specifications
Size (W x L) [mm]
Region (EU/AA)
A3 SEF (297 x 420)
A4 SEF (210 x 297)
A4 LEF (297 x 210)
A5 SEF (148 x 210)
A5 LEF (210 x 148 )
A6 SEF (105 x 148)
B4 SEF (257 x 364)
B5 SEF (182 x 257)
B5 LEF (257 x 182 )
B6 SEF (128 x 182 )
DLT SEF (11" x 17")
Legal SEF (8
1
/
2
" x 14")
Foolscap SEF (8
1
/
2
" x 13")
LT SEF (8
1
/
2
" x 11")
LT LEF (11" x 8
1
/
2
")
Gov. LG SEF (8
1
/
4
" x 14")
Folio SEF (8
1
/
4
" x 13")
F/GL SEF (8" x 13")
GLT SEF (8" x 10
1
/
2
")
Tray 1
-
-
-
K
-
K
-
-
-
-
-
H
-
K
-
-
-
-
-
-
-
K
-
-
-
K
NA EU/AA NA
G2
-
H
A
G1
K
-
-
B
A
B
G3
-
-
-
-
B
B
B
-
A3
B
A
A1
A
G4
B
A2
Tray 2
G3
B
A
G1
A
A4
B
G2
B
B
B
-
B
A
B
A3
EU/AA
A2
A
A1
Tray 3/4
1 drawer
/2 drawers bank
NA
G2
A
G1
EU/AA
A2
A
A1
A
G3
A
G4
A2
A3
B
A
A1
B
B
B
A
A3
A
A4
G2
G3
B
A
G1
B
B
B
Supported Paper Sizes
Size (W x L) [mm]
Region (EU/AA)
GLT LEF (10
1
/
2
" x 8")
Eng Quatro SEF (8" x 10")
Eng Quatro LEF (10" x 8")
Executive SEF (7
1
/
4
" x 10
1
/
2
")
Executive LEF (10
1
/
2
" x 7
1
/
4
")
HLT SEF (5
1
/
2
" x 8
1
/
2
")
HLT LEF (8
1
/
2
" x 5
1
/
2
")
SRA3 SEF (420 x 320)
SRA4 SEF
SRA4 LEF
Line slider 1 SEF
Line slider 1 LEF
Line slider 2 SEF
Line slider 2 LEF
Com10 SEF (104.8 x 241.3)
Com10 LEF (241.3 x 104.8)
Monarch SEF (98.4 x 190.5)
Monarch LEF (190.5 x 98.4)
C5 SEF (162 x 229)
C5 LEF (229 x 162)
C6 SEF (114 x 162)
C6LEF (162 x 114)
Tray 1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
NA EU/AA NA
-
-
B
-
-
-
-
-
B
A4
B
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
B
-
B
B
B
B
-
B
B
-
-
G5
-
-
-
Tray 2
-
B
B
-
-
A5
-
-
-
B
G4
B
-
EU/AA
-
B
-
B
-
B
B
B
B
Tray 3/4
1 drawer
/2 drawers bank
NA EU/AA
B
G5
-
-
-
B
A4
-
-
-
-
B
-
-
-
-
B
B
B
B
A5
-
-
-
B
G4
B
-
-
-
-
-
B
-
-
-
-
B
B
B
B
23
24
1. Specifications
Size (W x L) [mm] Tray 1 Tray 2
Region (EU/AA)
DL Env SEF (110 x 220)
DL Env LEF (220 x 110)
8K SEF (267 x 390)
16K SEF (195 x 267 )
16K LEF (267 x 195 )
13” x 19.2” SEF
13” x 19” SEF
13” x 18” SEF
12.6” x 19.2 SEF
12.6” x 18.5” SEF
12" x 18" SEF
12" x 18" LEF
11" x 15" SEF
11” x 14” SEF
10" x 15" SEF
10" x 14" SEF
8.5” x 13.4” SEF
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
NA EU/AA NA
B
-
B
B
-
-
-
-
B
B
-
-
-
-
-
-
-
-
-
-
-
-
-
-
B
A3
-
B
-
-
-
A5
-
-
B
B
-
B
-
-
-
G5
B
B
-
-
EU/AA
B
B
B
Remarks:
A Auto detectable. Also can be selected with size button of initial setting.
B Can be selected with size button from initial setting.
C Select this size by setting the dial.
D Set dial to “*”, then select with size button from initial setting.
-
-
B
A3
-
B
-
-
-
A5
B
B
-
-
Tray 3/4
1 drawer
/2 drawers bank
NA
B
B
B
EU/AA
B
B
B
B
B
-
-
-
-
B
B
-
B
-
-
-
G5
Supported Paper Sizes
E
F
<Bypass setting>
Copy window/Bypass/Standard size/Size select or select with the print bypass paper size/size button from initial setting.
Select with SP from preset paper sizes.
Cannot be selected from printer driver.
G
Switches which size to set as auto detect with SP.
*Example: The combination of A1-G1.
G (When not auto detectable) will be as same as B.
Combinations are only made from same region same tray.
*Example: The combination of G1 and J1.
G (When not auto detectable) will be as same as E.
Combinations are only made from same region same tray.
H Size fixed when shipping.
-
J
I
K
<Bypass setting>
With bypass tray, after 1 st
sheet trailing edge goes through, auto detects size, then fixed to size detected from the 2 nd
sheet.
<Bypass setting>
Auto detect of Copy window/Bypass/Standard size/Select with size button.
Select with SP from preset paper sizes.
Can be selected from printer driver.
Not available
Size (W x L) [mm]
Region (EU/AA)
A3 SEF (297 x 420)
A4 SEF (210 x 297)
A4 LEF (297 x 210)
A5 SEF (148 x 210)
E
E
E
NA
E
Bypass
EU/AA
J
J
J
J
25
26
1. Specifications
Size (W x L) [mm]
Region (EU/AA)
A5 LEF (210 x 148 )
A6 SEF (105 x 148)
B4 SEF (257 x 364)
B5 SEF (182 x 257)
B5 LEF (257 x 182 )
B6 SEF (128 x 182 )
DLT SEF (11" x 17")
Legal SEF (8
1
/
2
" x 14")
Foolscap SEF (8
1
/
2
" x 13")
LT SEF (8
1
/
2
" x 11")
LT LEF (11" x 8
1
/
2
")
Gov. LG SEF (8
1
/
4
" x 14")
Folio SEF (8
1
/
4
" x 13")
F/GL SEF (8" x 13")
GLT SEF (8" x 10
1
/
2
")
GLT LEF (10
1
/
2
" x 8")
Eng Quatro SEF (8" x 10")
Eng Quatro LEF (10" x 8")
Executive SEF (7
1
/
4
" x 10
1
/
2
")
Executive LEF (10
1
/
2
" x 7
1
/
4
")
HLT SEF (5
1
/
2
" x 8
1
/
2
")
HLT LEF (8
1
/
2
" x 5
1
/
2
")
SRA3 SEF (420 x 320)
SRA4 SEF
Bypass
-
E
-
E
-
E
E
E
E
J
E
E
E
EU/AA
J
J
J
J
J
E
E
E
-
J
E
E
-
-
E
-
J1
J
E
E
E
J
G1
E
E
E
NA
J
E
J
E
E
-
J
E
J
SRA4 LEF
Line slider 1 SEF
Size (W x L) [mm]
Region (EU/AA)
Line slider 1 LEF
Line slider 2 SEF
Line slider 2 LEF
Com10 SEF (104.8 x 241.3)
Com10 LEF (241.3 x 104.8)
Monarch SEF (98.4 x 190.5)
Monarch LEF (190.5 x 98.4)
C5 SEF (162 x 229)
C5 LEF (229 x 162)
C6 SEF (114 x 162)
C6LEF (162 x 114)
DL Env SEF (110 x 220)
DL Env LEF (220 x 110)
8K SEF (267 x 390)
16K SEF (195 x 267 )
16K LEF (267 x 195 )
13” x 19.2” SEF
13” x 19” SEF
13” x 18” SEF
12.6” x 19.2 SEF
12.6” x 18.5” SEF
12" x 18" SEF
Supported Paper Sizes
Bypass
-
-
-
-
-
E
EU/AA
E
-
-
-
E
*1
E
*1
E
*1
E
*1
E
*1
E
*1
-
E
*1
E
*1
E
*1
E
*1
E
E
E
-
-
-
-
J
-
-
-
NA
E
-
E
*1
E
*1
E
*1
E
*1
E
*1
E
*1
-
E
*1
E
*1
E
*1
E
*1
E
E
E
27
28
1. Specifications
12" x 18" LEF
Size (W x L) [mm]
Region (EU/AA)
11" x 15" SEF
11” x 14” SEF
10" x 15" SEF
10" x 14" SEF
8.5” x 13.4” SEF
E
-
NA
-
E
-
E
Bypass
Remarks:
A Auto detectable. Also can be selected with size button of initial setting.
B Can be selected with size button from initial setting.
C Select this size by setting the dial.
D Set dial to “*”, then select with size button from initial setting.
E
F
G
<Bypass setting>
Copy window/Bypass/Standard size/Size select or select with the print bypass paper size/size button from initial setting.
Select with SP from preset paper sizes.
Cannot be selected from printer driver.
Switches which size to set as auto detect with SP.
*Example: The combination of A1-G1.
G (When not auto detectable) will be as same as B.
Combinations are only made from same region same tray.
*Example: The combination of G1 and J1.
G (When not auto detectable) will be as same as E.
Combinations are only made from same region same tray.
H Size fixed when shipping.
EU/AA
-
E
-
-
E
E
Supported Paper Sizes
J
I
K
-
<Bypass setting>
With bypass tray, after 1 st
sheet trailing edge goes through, auto detects size, then fixed to size detected from the 2 nd
sheet.
<Bypass setting>
Auto detect of Copy window/Bypass/Standard size/Select with size button.
Select with SP from preset paper sizes.
Can be selected from printer driver.
Not available
*1
Even the paper size is in the range or available sizes for duplex, envelopes can not be done so.
Size (W x L) [mm]
A3 SEF (297 x 420)
A4 SEF (210 x 297)
A4 LEF (297 x 210)
A5 SEF (148 x 210)
A5 LEF (210 x 148 )
A6 SEF (105 x 148)
B4 SEF (257 x 364)
B5 SEF (182 x 257)
B5 LEF (257 x 182 )
Main unit tray
A
A
A
A
A
A
A
A
A
Main unit tray
1 bin tray
Upper tray
A
A
A
A
A
A
*1
A
A
A
Inner shit tray shift
A
A
A
A
A
A
A
A
A shifting
A
A
A
A
B
A
A
A
A
Side Tray
A
A
A
A
A
Bridge upper exit
A
A
A
A
Side tray
A
A
A
A
A
A
A
A
A
29
30
1. Specifications
Size (W x L) [mm]
B6 SEF (128 x 182 )
DLT SEF (11" x 17")
Legal SEF (8
1
/
2
" x 14")
Foolscap SEF (8
1
/
2
" x 13")
LT SEF (8
1
/
2
" x 11")
LT LEF (11" x 8
1
/
2
")
Gov. LG SEF (8
1
/
4
" x 14")
Folio SEF (8
1
/
4
" x 13")
F/GL SEF (8" x 13")
GLT SEF (8" x 10
1
/
2
")
GLT LEF (10
1
/
2
" x 8")
Eng Quatro SEF (8" x 10")
Eng Quatro LEF (10" x 8")
Executive SEF (7
1
/
4
" x
10
1
/
2
")
Executive LEF (10
7
1
/
4
")
1
/
2
" x
HLT SEF (5
1
/
2
" x 8
1
/
2
")
HLT LEF (8
1
/
2
" x 5
1
/
2
")
SRA3 SEF (420 x 320)
SRA4 SEF
SRA4 LEF
Line slider 1 SEF
Main unit tray
1 bin tray
Upper tray
A
A
A
A
A
A
A
*1
A
-
A
-
A
-
A
Main unit tray
A
A
A
A
A
A
A
A
-
A
-
A
-
A
A
A
A
A
A
-
A
A
A
-
A
A
A
*1
A
A
-
A
A
A
A
A
A
A
A
A
A
-
A
-
A
-
A
A
A
A
A
B
A
A
A
-
A
-
A
-
A
Inner shit tray shift shifting
Side Tray
A
A
A
A
Bridge upper exit
A
A
A
A
-
A
-
A
-
A
Side tray
A
A
A
A
A
A
A
A
A
-
A
-
A
-
A
A
B
A
B
-
A
A
A
A
A
-
A
-
A
A
A
A
Supported Paper Sizes
Main unit tray
1 bin tray
Size (W x L) [mm]
Line slider 1 LEF
Line slider 2 SEF
Line slider 2 LEF
Com10 SEF (104.8 x 241.3)
Com10 LEF (241.3 x 104.8)
Monarch SEF (98.4 x 190.5)
Monarch LEF (190.5 x 98.4)
C5 SEF (162 x 229)
C5 LEF (229 x 162)
C6 SEF (114 x 162)
C6LEF (162 x 114)
DL Env SEF (110 x 220)
DL Env LEF (220 x 110)
8K SEF (267 x 390)
16K SEF (195 x 267 )
16K LEF (267 x 195 )
13” x 19.2” SEF
13” x 19” SEF
13” x 18” SEF
12.6” x 19.2 SEF
12.6” x 18.5” SEF
12" x 18" SEF
Main unit tray
A
A
-
A
A
-
-
-
-
-
A
A
A
A
A
A
A
A
-
-
-
A
Upper tray
A
A
-
B
A
-
-
-
-
-
B
B
B
B
B
B
B
B
-
-
-
B
A
A
A
-
-
-
A
*1
A
*1
A
*1
A
*1
A
*1
-
A
*1
A
*1
A
*1
A
*1
A
*1
-
-
-
-
-
Inner shit tray shift shifting
Side Tray
A
A
A
-
Bridge upper exit
-
-
A
*1
A
*1
A
*1
A
*1
A
*1
-
A
*1
A
*1
A
*1
A
*1
A
*1
-
-
-
-
-
Side tray
A
A
-
-
A
-
-
-
-
-
B
B
-
B
-
B
-
B
-
-
-
B
A
A
-
B
A
-
-
-
-
-
B
B
B
B
B
B
B
B
-
-
-
B
31
32
1. Specifications
Size (W x L) [mm]
12" x 18" LEF
11" x 15" SEF
11” x 14” SEF
10" x 15" SEF
10" x 14" SEF
8.5” x 13.4” SEF
Main unit tray
1 bin tray
Main unit tray
A
A
-
-
A
A
Upper tray
A
A
-
-
A
A
A
A
-
-
A
*1
A
Inner shit tray shift shifting
B
A
-
-
A
A
Side Tray
Bridge upper exit
A
A
-
-
A
A
Side tray
A
A
-
-
A
A
Size (W x L) [mm]
A3 SEF (297 x 420)
A4 SEF (210 x 297)
A4 LEF (297 x 210)
A5 SEF (148 x 210)
A5 LEF (210 x 148 )
A6 SEF (105 x 148)
B4 SEF (257 x 364)
B5 SEF (182 x 257)
B5 LEF (257 x 182 )
B6 SEF (128 x 182 )
Paper exit
A
A
A
A
*1
A
*1
-
A
-
A
A
Staple
Shift Shifting
Single/
Double size
Staplin g amount
A
A
A
A
A
A
*1
A
*1
A
*1
A
A
*1
-
-
A
A
A
-
A
A
A
-
-
-
30
50
30
50
50
-
50
-
-
-
A
A
EU 2
SC 4
Holes
A
A
A
-
A
-
-
-
-
-
-
-
A
-
A
-
Punch
NA 3
EU 4
Holes
NA 2
Holes
-
-
-
-
-
-
A
B
A
-
Supported Paper Sizes
Size (W x L) [mm]
DLT SEF (11" x 17")
Legal SEF (8
1
/
2
" x 14")
Foolscap SEF (8
1
/
2
" x 13")
LT SEF (8
1
/
2
" x 11")
LT LEF (11" x 8
1
/
2
")
Gov. LG SEF (8
1
/
4
" x 14")
Folio SEF (8
1
/
4
" x 13")
F/GL SEF (8" x 13")
GLT SEF (8" x 10
1
/
2
")
GLT LEF (10
1
/
2
" x 8")
Eng Quatro SEF (8" x 10")
Eng Quatro LEF (10" x 8")
Executive SEF (7
1
/
4
" x
10
1
/
2
")
Executive LEF (10
7
1
/
4
")
1
/
2
" x
HLT SEF (5
1
/
2
" x 8
1
/
2
")
HLT LEF (8
1
/
2
" x 5
1
/
2
")
SRA3 SEF (420 x 320)
SRA4 SEF
SRA4 LEF
Line slider 1 SEF
Line slider 1 LEF
A
A
*1
-
A
*1
A
*1
A
*1
-
-
A
-
-
-
-
-
-
A
Paper exit Staple
Shift Shifting
Single/
Double size
Staplin g amount
A
A
A
A
A
*1
-
-
A
*1
-
A
A
A
A
A
A
A
A
A
A
-
A
-
A
-
A
A
A
A
A
A
A
-
-
-
-
-
50
50
30
30
30
30
30
-
-
-
-
-
A
A
A
A
-
-
EU 2
SC 4
Holes
A
-
-
-
-
-
A A A 50 A
-
A
-
-
-
-
Punch
NA 3
EU 4
Holes
A
-
-
-
-
-
NA 2
Holes
A
A
-
-
A
A
A
-
-
-
-
-
A
A
-
-
-
-
-
-
-
50
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
33
34
1. Specifications
Size (W x L) [mm]
Paper exit Staple
Shift Shifting
Single/
Double size
Staplin g amount
Line slider 2 SEF -
Line slider 2 LEF
Com10 SEF (104.8 x 241.3) A
-
*1
Com10 LEF (241.3 x 104.8) A
*1,3,4
Monarch SEF (98.4 x 190.5) A
*1
Monarch LEF (190.5 x 98.4) A
*1,3,4
C5 SEF (162 x 229) A
*1
C5 LEF (229 x 162)
C6 SEF (114 x 162)
A
*1
A
*1
C6LEF (162 x 114)
DL Env SEF (110 x 220)
DL Env LEF (220 x 110)
A
*1,3,4
A
*1
A
*1,3,4
8K SEF (267 x 390)
16K SEF (195 x 267 )
16K LEF (267 x 195 )
13” x 19.2” SEF
A
A
A
-
13” x 19” SEF
13” x 18” SEF
12.6” x 19.2 SEF
12.6” x 18.5” SEF
12" x 18" SEF
12" x 18" LEF
-
-
-
A
*1
-
-
A
A
-
-
A
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
30
50
50
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
A
A
-
-
A
-
-
-
-
-
-
-
-
-
-
EU 2
SC 4
Holes
-
-
-
-
-
-
-
-
-
-
-
-
-
-
A
-
-
A
A
-
-
A
*1
A
*1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Punch
NA 3
EU 4
Holes
-
-
-
-
-
-
-
NA 2
Holes
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Supported Paper Sizes
Size (W x L) [mm]
11" x 15" SEF
11” x 14” SEF
10" x 15" SEF
10" x 14" SEF
8.5” x 13.4” SEF
Paper exit Staple
Shift Shifting
Single/
Double size
Staplin g amount
A
*1
-
-
A
*1
-
A
-
-
A
-
-
-
-
-
A
-
-
-
-
30
-
A
-
-
EU 2
SC 4
Holes
-
-
-
-
-
Punch
NA 3
EU 4
Holes
-
NA 2
Holes
-
-
-
-
A
Size (W x L) [mm]
A3 SEF (297 x 420)
A4 SEF (210 x 297)
A4 LEF (297 x 210)
A5 SEF (148 x 210)
A5 LEF (210 x 148 )
A6 SEF (105 x 148)
B4 SEF (257 x 364)
Paper exit
Hal f fold
Staple Punch
Pro of
Shi ft
Shi ftin g
Sa ddl e stitc h
Mi ddl e fold
Single/
Do ubl e stit ch
Sta ple am oun t
Sa ddl e stit ch
Sa ddl e stitc h am oun t
EU
2
SC
4
Ho les
N
A
2
H ol es
A A A A A
*5
A A A A A
*5
A A A -
A 30 A 15 A A A
A 50 A 15 A B -
A 50 A A A
NA
3
EU
4
Hol es
A B B -
A A A -
-
-
-
-
-
-
A
A
A
B
-
-
A B -
A A A A A
*5
A 30
-
A
-
15
-
A
-
A
-
A
35
36
1. Specifications
Size (W x L) [mm]
B5 SEF (182 x 257)
B5 LEF (257 x 182 )
B6 SEF (128 x 182 )
DLT SEF (11" x 17")
Legal SEF (8
1
/
2
" x 14")
Foolscap SEF (8
1
/
2
" x 13")
LT SEF (8
1
/
2
" x 11")
LT LEF (11" x 8
1
/
2
")
Gov. LG SEF (8
1
/
4
" x 14")
Folio SEF (8
1
/
4
" x 13")
F/GL SEF (8" x 13")
GLT SEF (8" x 10
1
/
2
")
GLT LEF (10
1
/
2
" x 8")
Eng Quatro SEF (8" x 10")
Eng Quatro LEF (10" x 8")
Executive SEF (7
1
/
4
" x
10
1
/
2
")
Executive LEF (10
7
1
/
4
")
1
/
2
" x
Paper exit
Hal f fold
Staple Punch
Pro of
Shi ft
Shi ftin g
Sa ddl e stitc h
Mi ddl e fold
Single/
Sta
Do ubl e stit ch ple am oun t
Sa ddl e stit ch
Sa ddl e stitc h am oun t
EU
2
SC
4
Ho les
N
A
2
H ol es
A B B A A
A A A -
*5
A 50 A 15 A A -
A 50 A A A
NA
3
EU
4
Hol es
A B A -
A A A A A
*5
A 30
-
A
-
15
-
A
-
A
-
A
A A A A A
*5
A 30 A 15 A A -
A A A A 30 -
A A A A A
*5
A 50 A
-
15
A
A
A
A
-
-
A A A -
A A A -
A A A -
A A A -
-
-
A A A -
-
-
-
-
-
-
A
A 30 -
A 30 -
A 30 -
-
-
A
-
50
-
50
-
-
-
-
-
-
-
-
-
-
-
-
A
-
-
A
-
A
-
-
A
-
A
A A -
A A -
A A -
-
-
-
-
A A A A 50 A A -
A A A A 50 A A A
Supported Paper Sizes
Paper exit
Hal f fold
Staple Punch
Size (W x L) [mm]
HLT SEF (5
1
/
2
" x 8
1
/
2
")
HLT LEF (8
1
/
2
" x 5
1
/
2
")
SRA3 SEF (420 x 320)
SRA4 SEF
SRA4 LEF
Line slider 1 SEF
Line slider 1 LEF
Line slider 2 SEF -
-
Line slider 2 LEF -
Com10 SEF (104.8 x 241.3) -
-
-
A B B -
-
A A -
A A A -
-
A A -
-
-
-
-
-
-
-
-
-
-
Com10 LEF (241.3 x 104.8) -
Monarch SEF (98.4 x 190.5) -
Monarch LEF (190.5 x 98.4) -
C5 SEF (162 x 229) -
-
-
-
-
-
-
-
C5 LEF (229 x 162)
C6 SEF (114 x 162)
C6LEF (162 x 114)
DL Env SEF (110 x 220)
Pro of
-
-
-
-
Shi ft
-
-
-
-
Shi ftin g
Sa ddl e stitc h
Mi ddl e fold
Single/
Sta
Do ubl ple am e stit ch oun t
Sa ddl e stit ch
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
A
-
-
-
-
-
30
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Sa ddl e stitc h am oun t
EU
2
SC
4
Ho les
N
A
2
H ol es
A A -
-
-
-
-
-
NA
3
EU
4
Hol es
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
37
38
1. Specifications
DL Env LEF (220 x 110)
8K SEF (267 x 390)
16K SEF (195 x 267 )
16K LEF (267 x 195 )
13” x 19.2” SEF
13” x 19” SEF
13” x 18” SEF
12.6” x 19.2 SEF
12.6” x 18.5” SEF
12" x 18" SEF
12" x 18" LEF
11" x 15" SEF
11” x 14” SEF
10" x 15" SEF
10" x 14" SEF
8.5” x 13.4” SEF
Size (W x L) [mm]
Paper exit
Hal f fold
Staple
Pro of
Shi ft
Shi ftin g
Sa ddl e stitc h
Mi ddl e fold
Single/
Sta
Do ubl ple am e stit ch oun t
Sa ddl e stit ch
Sa ddl e stitc h am oun t
EU
2
SC
4
Ho les
N
A
2
H ol es
-
A A A -
-
A A A -
A A A -
-
-
-
-
-
-
A 30 -
-
A 50 -
A 50 -
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
A A A A A
*5
A 50
-
A
-
15
-
-
-
-
-
-
-
-
NA
3
EU
4
Hol es
-
A A A
A A -
A A A
-
-
-
A A A -
-
A 50 -
-
-
-
-
-
-
-
-
-
-
-
A A A A 50 -
A A A A A
*5
A 30 -
-
-
-
-
-
-
-
-
-
A
-
-
A
A
Punch
-
A
-
-
A
A
A
-
-
A
-
-
Size (W x L) [mm]
A3 SEF (297 x 420)
A4 SEF (210 x 297)
A4 LEF (297 x 210)
A5 SEF (148 x 210)
A5 LEF (210 x 148 )
A6 SEF (105 x 148)
B4 SEF (257 x 364)
B5 SEF (182 x 257)
B5 LEF (257 x 182 )
B6 SEF (128 x 182 )
DLT SEF (11" x 17")
Legal SEF (8
1
/
2
" x 14")
Foolscap SEF (8
1
/
2
" x 13")
LT SEF (8
1
/
2
" x 11")
LT LEF (11" x 8
1
/
2
")
Gov. LG SEF (8
1
/
4
" x 14")
Folio SEF (8
1
/
4
" x 13")
F/GL SEF (8" x 13")
GLT SEF (8" x 10
1
/
2
")
GLT LEF (10
1
/
2
" x 8")
Eng Quatro SEF (8" x 10")
Eng Quatro LEF (10" x 8")
A
A
A
-
A
A
A
A
-
A
-
Paper exit
Bridge upper paper exit
A
A
A
A
A
A
A
A
A
A
A
Supported Paper Sizes
A
A
A
-
A
A
A
A
-
A
-
Bridge
Finisher Bridge
A
A
A
A
A
A
A
A
A
A
A
39
40
1. Specifications
Size (W x L) [mm]
Executive SEF (7
1
/
4
" x
10
1
/
2
")
Executive LEF (10
7
1
/
4
")
1
/
2
" x
HLT SEF (5
1
/
2
" x 8
1
/
2
")
HLT LEF (8
1
/
2
" x 5
1
/
2
")
SRA3 SEF (420 x 320)
SRA4 SEF
SRA4 LEF
Line slider 1 SEF
Line slider 1 LEF
Line slider 2 SEF
Line slider 2 LEF
Com10 SEF (104.8 x 241.3)
Com10 LEF (241.3 x 104.8)
Monarch SEF (98.4 x 190.5)
Monarch LEF (190.5 x 98.4)
C5 SEF (162 x 229)
C5 LEF (229 x 162)
C6 SEF (114 x 162)
C6LEF (162 x 114)
DL Env SEF (110 x 220)
DL Env LEF (220 x 110)
8K SEF (267 x 390)
Paper exit
Bridge upper paper exit
A
A
A
A
A
A
-
-
-
-
-
A
*1
A
*1
A
*1
A
*1
A
*1
A
*1
A
*1
A
*1
A
*1
A
*1
A
Bridge
Finisher Bridge
A
A
-
-
-
-
-
A
-
-
-
-
-
A
A
A
A
-
-
-
-
-
Size (W x L) [mm]
16K SEF (195 x 267 )
16K LEF (267 x 195 )
13” x 19.2” SEF
13” x 19” SEF
13” x 18” SEF
12.6” x 19.2 SEF
12.6” x 18.5” SEF
12" x 18" SEF
12" x 18" LEF
11" x 15" SEF
11” x 14” SEF
10" x 15" SEF
10" x 14" SEF
8.5” x 13.4” SEF
Paper exit
Bridge upper paper exit
A
A
-
-
-
-
A
A
A
-
-
-
-
A
Remarks:
A Paper through, paper exit available.
B Will not guarantee, but paper can go through or exit.
Not available.
*1 Out of the true up precision guarantee.
*2 Multi folding can be done up to 5 sheets.
*3 Envelopes can only go through each at a time.
*4 Except envelopes with triangle flap.
Supported Paper Sizes
-
A
A
A
-
-
-
-
A
Bridge
Finisher Bridge
A
A
-
-
-
41
42
1. Specifications
*5
Only one sheet can be half folded with saddle stitch mode.
Therefore, multi sheets/sets must be paginated and exit one at a time.
Option Specifications
Paper size:
Item
Paper weight:
Paper capacity (80 g/m
2
, 20 lb.
Bond):
Power consumption:
Dimensions (W × D × H):
Weight:
Specification
A3 SEF, A4 SEF/LEF, A5 SEF, B4 JIS SEF, B5 JIS SEF/LEF, A6
LEF, 11 × 17 SEF, 8 1/2 × 14 SEF, 8 1/2 × 13 LEF, 8 1/2 ×
11 SEF/LEF, 8 1/4 × 14 SEF, 8 1/4 × 13 SEF, 8 × 13 SEF, 8 ×
10 SEF, 7 1/4 × 10 1/2 SEF/LEF, 8K SEF, 16K SEF/LEF, 12 ×
18 SEF, 11 × 15 SEF, 10 × 14 SEF, 4 1/8 × 9 1/2 SEF, C5
Env SEF, SRA3 SEF, custom size
52–300 g/m
2
(14 lb. Bond–110 lb. Cover)
550 sheets × 1 tray
19 W or less (Power is supplied from the main unit.)
587 × 685 × 120 mm (23.2 × 27.0 × 4.8 inches)
Approx. 11 kg (24.3 lb.)
Paper size:
Item
Paper weight:
Paper capacity (80 g/m
2
, 20 lb.
Bond):
Power consumption:
Dimensions (W × D × H):
Specification
A3 SEF, A4 SEF/LEF, A5 LEF, B4 JIS SEF, B5 JIS SEF/LEF, 11 ×
17 SEF, 8 1/2 × 14 SEF, 8 1/2 × 13 LEF, 8 1/2 × 11 SEF/
LEF, 8 1/4 × 14 SEF, 8 1/4 × 13 SEF, 8 × 13 SEF, 8 × 10 SEF,
7 1/4 × 10 1/2 SEF/LEF, 8K SEF, 16K SEF/LEF, 12 × 18 SEF,
11 × 15 SEF, 10 × 14 SEF, 4 1/8 × 9 1/2 SEF, C5 Env SEF,
SRA3 SEF, custom size
60–300 g/m
2
(16 lb. Bond–110 lb. Cover)
550 sheets × 2 trays
21 W or less (Power is supplied from the main unit.)
587 × 685 × 247 mm (23.2 × 27.0 × 9.8 inches)
43
44
1. Specifications
Weight:
Item Specification
Approx. 22.0 kg (48.5 lb.)
Mode:
Original Size:
Original weight:
Item Specification
Batch mode, SADF mode, Mixed Sizes mode, Original
Orientation mode, and Custom Size originals mode
EU/AA
• One-sided originals: A3 SEF-B6 JIS SEF/LEF, 11 × 17
SEF-8 1/2 × 11 SEF/LEF
• Two-sided originals: A3 SEF-A5 SEF/LEF, 11 × 17 SEF-8
1/2 × 11 SEF/LEF
NA
• One-sided originals: 11 × 17 SEF-5 1/2 × 8 1/2 SEF/
LEF, A3 SEF-A4 SEF/LEF
• Two-sided originals: 11 × 17 SEF-5 1/2 × 8 1/2 SEF/
LEF, A3 SEF-A4 SEF/LEF
• One-sided originals: 40-128 g/m2 (11-34 lb. Bond)
• Two-sided originals: 52-128 g/m2 (14-34 lb. Bond)
100 sheets Number of originals to be set (81 g/m2, 20 lb. Bond):
Power consumption:
Dimensions (W × D × H):
Weight:
42 W or less (Power is supplied from the main unit.)
565 × 500 × 125 mm (22.3 × 19.7 × 5.0 inches)
Approx. 9 kg (19.9 lb.)
Configuration:
Item Specification
Automatic document feed duple× scanner (one pass two-side scanning)
Mode:
Original size
Item
Scanning origin point:
Original setting:
Original feed:
Original separation:
Original scanning method:
Original tray capacity:
Power consumption:
Dimensions (W × D × H):
Weight:
Option Specifications
Specification
Batch mode, SADF mode, Mixed Sizes mode, Original
Orientation mode, and Custom Size originals mode
EU/AA
• One-sided originals: A3 SEF-B6 JIS SEF/LEF, 11 × 17
SEF-8 1/2 × 11 SEF/LEF
• Two-sided originals: A3 SEF-A5 SEF/LEF, 11 × 17 SEF-8
1/2 × 11 SEF/LEF
NA
• One-sided originals: 11 × 17 SEF-5 1/2 × 8 1/2 SEF/
LEF, A3 SEF-A4 SEF/LEF
• Two-sided originals: 11 × 17 SEF-5 1/2 × 8 1/2 SEF/
LEF, A3 SEF-A4 SEF/LEF
Origin at rear upper left corner
Face-up on original tray
Feeds from top of stack on original tray
Feed belt and reverse roller separation by friction
Through-sheet method (Front: White platen plate, Back: Color
CIS and white roller)
220 sheets (80 g/m
2
, 20 lb. Bond)
55 W or less (Power is supplied from the main unit.)
587 × 520 × 175 mm (23.2 × 20.5 × 6.9 in.)
Approx. 14 kg (30.9 lb.)
45
46
1. Specifications
Paper size:
Power consumption:
Dimensions (W × D × H):
Weight:
Item
Paper weight:
Paper capacity (80 g/m
2
, 20 lb.
Bond):
Specification
A3 SEF, A4 SEF/LEF, A5 SEF/LEF, A6 SEF, B4 JIS SEF, B5 JIS
SEF/LEF, B6 JIS SEF, 11 × 17 SEF, 8 1/2 × 14 SEF, 8 1/2 ×
13 LEF, 8 1/2 × 11 SEF/LEF, 8 1/4 × 14 SEF, 8 1/4 × 13
SEF, 8 × 13 SEF, 8 × 10 SEF, 7 1/4 × 10 1/2 SEF/LEF, 5 1/2
× 8 1/2 SEF, 4 1/8 × 9 1/2 SEF/LEF, 3 7/8 × 7 1/2 SEF/
LEF, C5 Env SEF/LEF, C6 Env SEF/LEF, DL Env SEF/LEF, 8K
SEF, 16K SEF/LEF, 12 × 18 SEF, 11 × 15 SEF, 10 × 14 SEF,
SRA3 SEF, SRA4 SEF/LEF, custom size
52–300 g/m
2
(14 lb. Bond–110 lb. Cover)
• Internal tray 1:
250 sheets: A4, 81/2 × 11 or smaller
125 sheets: B4 JIS, 81/2 × 14 or larger
• External tray:
125 sheets
12 W (Power is supplied from the main unit.)
800 × 549 × 156 mm (31.5 × 21.7 × 6.2 inches)
Approx. 4 kg (8.9 lb.)
Item
Paper size:
Paper weight:
Specification
A3 SEF, A4 SEF/LEF, A5 SEF/LEF, A6 SEF, B4 JIS SEF, B5 JIS
SEF/LEF, B6 JIS SEF, 11 × 17 SEF, 8 1/2 × 14 SEF, 8 1/2 ×
13 LEF, 8 1/2 × 11 SEF/LEF, 8 1/4 × 14 SEF, 8 1/4 × 13
SEF, 8 × 13 SEF, 8 × 10 SEF, 7 1/4 × 10 1/2 SEF/LEF, 5 1/2
× 8 1/2 SEF, 4 1/8 × 9 1/2 SEF/LEF, 3 7/8 × 7 1/2 SEF/
LEF, C5 Env SEF/LEF, C6 Env SEF/LEF, DL Env SEF/LEF, 8K
SEF, 16K SEF/LEF, 12 × 18 SEF, 11 × 15 SEF, 10 × 14 SEF,
SRA3 SEF, SRA4 SEF/LEF, custom size
60–300 g/m
2
(16 lb. Bond–110 lb. Cover)
Option Specifications
Item Specification
Paper sizes that can be shifted: A3 SEF, A4 SEF/LEF, A5 SEF/LEF, A6 SEF, B4 JIS SEF, B5 JIS
SEF/LEF, B6 JIS SEF, 11 × 17 SEF, 8 1/2 × 14 SEF, 8 1/2 ×
13 LEF, 8 1/2 × 11 SEF/LEF, 8 1/4 × 14 SEF, 8 1/4 × 13
SEF, 8 × 13 SEF, 8 × 10 SEF, 7 1/4 × 10 1/2 SEF/LEF, 5 1/2
× 8 1/2 SEF, 4 1/8 × 9 1/2 SEF/LEF, 3 7/8 × 7 1/2 SEF/
LEF, C5 Env SEF/LEF, C6 Env SEF/LEF, DL Env SEF/LEF, 8K
SEF, 16K SEF/LEF, 12 × 18 SEF, 11 × 15 SEF, 10 × 14 SEF,
SRA3 SEF, SRA4 SEF/LEF, custom size
Paper weight that can be shifted: 60–300 g/m
2
(16 lb. Bond–110 lb. Cover)
Stack capacity (80 g/m
2
, 20 lb.
Bond):
• 250 sheets: A4, 81/2 × 11 or smaller
• 125 sheets: B4 JIS, 81/2 × 14 or larger
Power consumption: 4.3 W (Power is supplied from the main unit.)
Dimensions (W × D × H):
Weight:
420 × 489 × 107 mm (16.6 × 19.3 × 4.3 inches)
Approx. 2 kg (4.5 lb.)
Number of bins:
Paper size:
Item
Paper weight:
Paper capacity (80 g/m
2
, 20 lb.
Bond):
Power consumption:
Dimensions (W × D × H):
Weight:
Specification
1
A3 SEF A4 SEF/LEF, A5 SEF/LEF, B4 JIS SEF B5 JIS SEF/LEF,
11 × 17 SEF, 8 1/2 × 14 SEF, 8 1/2 × 13 LEF, 8 1/2 × 11
SEF/LEF, 8 1/4 × 14 SEF, 8 1/4 × 13 SEF, 8 × 13 SEF, 8 × 10
SEF, 7 1/4 × 10 1/2 SEF/LEF, 51/2 × 8 1/2 SEF, 8K SEF,
16K SEF/LEF, 11 × 15 SEF, 10 × 14 SEF, SRA3 SEF, SRA4
SEF/LEF, custom size
52–300 g/m
2
(14 lb. Bond–110 lb. Cover)
125 sheets
1 W or less (Power is supplied from the main unit.)
444 × 450 × 150 mm (17.5 × 17.8 × 6.0 inches)
Approx. 2 kg (4.5 lb.)
47
48
1. Specifications
Item
Stack capacity (80 g/m
2
, 20 lb.
Bond):
Power consumption:
Dimensions (W × D × H):
Weight:
Specification
• 250 sheets: A4, 81/2 × 11 or smaller
• 125 sheets: B4 JIS, 81/2 × 14 or larger
15 W (Power is supplied from the main unit.)
412 × 466 × 143 mm (16.3 × 18.4 × 5.7 inches)
Approx. 4 kg (8.9 lb.)
Paper size:
Item Specification
A3 SEF, A4 SEF/LEF, A5 SEF/LEF, A6 SEF, B4 JIS SEF, B5 JIS
SEF/LEF, B6 JIS SEF, 11 × 17 SEF, 8 1/2 × 14 SEF, 8 1/2 ×
13 LEF, 8 1/2 × 11 SEF/LEF, 8 1/4 × 14 SEF, 8 1/4 × 13
SEF, 8 × 13 SEF, 8 × 10 SEF, 7 1/4 × 10 1/2 SEF/LEF, 5 1/2
× 8 1/2 SEF, 4 1/8 × 9 1/2 SEF/LEF, 3 7/8 × 7 1/2 SEF/
LEF, C5 Env SEF/LEF, C6 Env SEF/LEF, DL Env SEF/LEF, 8K
SEF, 16K SEF/LEF, 12 × 18 SEF, 11 × 15 SEF, 10 × 14 SEF,
SRA3 SEF, SRA4 SEF/LEF, custom size
60–300 g/m
2
(16 lb. Bond–110 lb. Cover) Paper weight:
Paper sizes that can be shifted: A3 SEF, A4 SEF/LEF, A5 SEF/LEF, B4 JIS SEF, B5 JIS SEF/LEF,
11 × 17 SEF, 8 1/2 × 14 SEF, 8 1/2 × 13 LEF, 8 1/2 × 11
SEF/LEF, 8 1/4 × 14 SEF, 8 1/4 × 13 SEF, 8 × 13 SEF, 8 × 10
SEF, 7 1/4 × 10 1/2 SEF/LEF, C5 Env SEF/LEF, 8K SEF, 16K
SEF/LEF, 11 × 15 SEF, 10 × 14 SEF, SRA4 LEF, custom size
Paper weight that can be shifted: 64–105 g/m
2
(17–28 lb. Bond)
Stack capacity (80 g/m
2
, 20 lb.
Bond):
• 500 sheets: A4, 81/2 × 11 or smaller
• 250 sheets: B4 JIS, 81/2 × 14 or larger
Staple paper size: A3 SEF, A4 SEF/LEF, B4 JIS SEF, B5 JIS SEF/LEF, 11 × 17 SEF,
8 1/2 × 14 SEF, 8 1/2 × 13 LEF, 8 1/2 × 11 SEF/LEF, 8 1/4
× 14 SEF, 8 1/4 × 13 SEF, 7 1/4 × 10 1/2 SEF/LEF, 8K SEF,
16K SEF/LEF
Option Specifications
Item
Staple paper weight:
Staple capacity (80 g/m
2
, 20 lb.
Bond):
Stack capacity after stapling (80 g/m
2
, 20 lb. Bond):
Staple position:
Power consumption:
Dimensions (W × D × H):
Weight:
Specification
64–105 g/m
2
(17–28 lb. Bond)
• Without Mixed Size:
30 sheets:
A3 SEF, B4 JIS SEF, 11 × 17 SEF, 8 1/2 × 14 SEF, 8 1/2
× 13 LEF, 8 1/4 × 14 SEF, 8 1/4 × 13 SEF, 8K SEF
50 sheets:
A4 SEF/LEF, B5 JIS SEF/LEF, 8 1/2 × 11 SEF/LEF, 7 1/4
× 10 1/2 SEF/LEF, 16K SEF/LEF
• With Mixed Size:
30 sheets:
A3 SEF/ A4 LEF, B4 JIS SEF/ B5 JIS SEF, 11 × 17 SEF/8
1/2 × 11 SEF
• 2–9 sheets: 55–46 sets (A4 LEF, B5 JIS LEF, 8 1/2 × 11
LEF)
• 10–50 sheets: 45–10 sets (A4 LEF, B5 JIS LEF, 8 1/2 ×
11LEF)
• 2–9 sheets: 55–27 sets (A4 SEF, B5 JIS SEF, 8 1/2 × 11
SEF)
• 10– 50 sheets: 25–8 sets (A4 SEF, B5 JIS SEF, 8 1/2 ×
11 SEF)
• 2–9 sheets: 55–27 sets (A3 SEF, B4 JIS SEF, 11 × 17 SEF,
8 1/2 × 14 SEF)
• 10–30 sheets: 25–8 sets (A3 SEF, B4 JIS SEF, 11 × 17
SEF, 8 1/2 × 14 SEF)
Top 1, Bottom 1, Left 2, Top 2
• 50 W or less (without punch unit) (Power is supplied from the main unit.)
• 60 W or less (with punch unit) (Power is supplied from the main unit.)
546 × 523 × 170 mm (21.5 × 20.6 × 6.7 inches)
Approx. 13 kg (28.7 lb.) (without punch unit)
Approx. 17 kg (37.5 lb.) (with punch unit)
49
50
1. Specifications
Item
Type
Shift tray
No. of sheets which can be accommodated
Paper thicknesses which can be handled
Up/down shift function
Left/right shift function
Stapling function
Punching function
Remainder detection
Full-load detection
Paper detection
Power consumption
Power source
Case system
Yes
A4, 8
1
/
2
×11 or smaller: 500 / height: lower than 57mm
B4, 8
1
/
2
×14 or larger: 250 / height: lower than 28.5mm
52g/m
2
-300g/m
2
Specification
No
Yes
Yes
Option
No
Yes
No
Less than 47W (24V DC /2A)
24V DC (supplied from main printer), 5V SC (generated by FIN board), SELV (super-low voltage secondary power supply)
Item
No. of sheets which can be stitched
Specification
A3 SEF, B4 SEF, 11"×17" SEF, 8
1
8
1
/
4
”×14” SEF, 8
1
/
4
/
2
”×13” SEF: 30
”×14” SEF, 8
1
/
2
”×13” SEF,
A4 LEF / SEF, B5 LEF / SEF, 8
1
/
2
"×11" LEF / SEF,
7
1
/
4
"×10
1
/
2
" LEF / SEF: 50
When loading mixed widths: 30
Option Specifications
Item
Sizes which can be stitched
Thicknesses which can be stitched
Stitching position
Staple supply
Stitching capacity
Specification
A3 SEF, B4 SEF, 11"×17" SEF, 8
1
/
2
”×14” SEF, 8
8
1
/
4
”×14” SEF, 8
1
/
4
”×13” SEF
1
/
2
”×13” SEF,
A4 LEF / SEF, B5 LEF / SEF, 8
1
/
2
"×11" LEF / SEF,
7
1
/
4
"×10
1
/
2
" LEF / SEF
52g/m
2
-105g/m
2
The quality for sheets of paper which are thinner than 64g/m
2 is not guaranteed.
No. of sheets to be stitched decreases when sheets of paper are thicker than 64g/m
2
, depending on the weight.
Top, bottom, 2 positions on the left, 2 positions on the top
Refill charge to dedicated staple cartridge
5000 / cartridge
Paper size:
Punch unit type
2 & 4 holes type: 2 holes
2 & 4 holes type: 2 holes
2 & 4 holes type: 4 holes
2 & 4 holes type: 4 holes
4 holes type: 4 holes
4 holes type: 4 holes
2 & 3 holes type: 2 holes
2 & 3 holes type: 2 holes
2 & 3 holes type: 3 holes
Paper size
SEF: A3, A4, B4 JIS, B5 JIS, 11 × 17, 8 1/2 × 14, 8 1/2 ×
13, 8 1/2 × 11, 7 1/4 × 10 1/2, 8K, 16K
LEF: A4, B5 JIS, 8 1/2 × 11, 16K
SEF: A3, 11 × 17
LEF: A4, 8 1/2 × 11
SEF: A3, A4, B4 JIS, B5 JIS, 11 × 17, 8 1/2 × 14, 8 1/2 ×
13, 8 1/2 × 11, 7 1/4 × 10 1/2
LEF: A4, B5 JIS, 8 1/2 × 11
SEF: A3, 11 × 17, 8 1/2 × 14, 8 1/2 × 13, 8 1/2 × 11, 7
1/4 × 10 1/2
LEF: A4, 8 1/2 × 11
SEF: A3, 11 × 17
51
52
1. Specifications
Punch unit type
2 & 3 holes type: 3 holes LEF: A4, 8 1/2 × 11
Paper weight:
60–169 g/m
2
(16 lb. Bond –90 lb. Index)
Paper size
Item Specification
Paper size:
Paper weight:
Paper sizes that can be shifted: A3 SEF, A4 LEF/SEF, B4 JIS SEF, B5 JIS LEF/SEF, 11 × 17 SEF,
8 1/2 × 14 SEF, 8 1/2 × 13 SEF, 8 1/2 × 11 LEF/SEF, 8 1/4
× 14 SEF, 8 1/4 × 13 SEF, 7 1/4 × 10 1/2 LEF/SEF, 8K SEF,
16K LEF/SEF, custom size
Paper weight that can be shifted: 64–80 g/m
2
(17–20 lb. Bond)
Stack capacity (80 g/m
2
, 20 lb.
Bond):
• 250 sheets or more:
A4 LEF, B5 JIS LEF/SEF, 81/2 × 11 LEF/SEF
• 125 sheets:
A3 SEF to A4 SEF, B4 JIS SEF, 81/2 × 14 SEF, 11 × 17
SEF
Stapling paper size:
A3 SEF, A4 LEF/SEF, B4 JIS SEF, B5 JIS LEF/SEF, 11 × 17 SEF,
8 1/2 × 14 SEF, 8 1/2 × 13 SEF, 8 1/2 × 11 LEF/SEF, 8 1/4
× 14 SEF, 8 1/4 × 13 SEF, 7 1/4 × 10 1/2 LEF/SEF, 8K SEF,
16K LEF/SEF, custom size
50–300 g/m
2
(14 lb. Bond–110 lb. Cover)
A3 SEF, A4 LEF/SEF, B4 JIS SEF, B5 JIS LEF/SEF, 11 × 17 SEF,
8 1/2 × 14 SEF, 8 1/2 × 13 SEF, 8 1/2 × 11 LEF/SEF, 8 1/4
× 14 SEF, 8 1/4 × 13 SEF, 7 1/4 × 10 1/2 LEF/SEF, 8K SEF,
16K LEF/SEF
64–80 g/m
2
(17–20 lb. Bond) Stapling paper weight:
Stapling capacity (80 g/m
2
, 20 lb. Bond):
5 sheets:
A3 SEF, A4 LEF/SEF, B4 JIS LEF/SEF, B5JIS LEF/SEF, 11×17
SEF, 8 1/2×14 SEF, 8 1/2×13 SEF 81/2×11 LEF/SEF, 8
4/1×14SEF, 8 1/4×13 SEF, 7 1/4×10 1/2 LEF/ SEF, 8K
SEF, 16K LEF SEF
Option Specifications
Item
Stack capacity after stapling (80 g/m
2
, 20 lb. Bond):
Staple position:
Power consumption:
Dimensions (W × D × H):
Weight:
Specification
• 30 sets or more (A4 LEF, 81/2 × 11 LEF)
• 20 sets or more (B5 JIS LEF/SEF)
• 15 sets or more (A3 SEF- A4 SEF, B4 JIS SEF, 11 × 17
SEF, 8 1/2 × 11 SEF)
Bottom Slant
30 W or less
435 × 515 × 150 mm (17.2 × 20.3 × 6.0 inches)
Approx. 10 kg (22.1 lb.)
Item
Type
Shift tray
No. of sheets which can be accommodated
Paper thicknesses which can be handled
Up/down shift function
Left/right shift function
Stapling function
Punching function
Remainder detection
Full-load detection
Paper detection
Power consumption
No
Yes
Yes
No
No
Yes
No
Less than 30W
Specification
Case system
Yes
A4, 8
1
/
2
×11 or smaller: 250
B4, 8
1
/
2
×14 or larger: 125
52g/m
2
-300g/m
2
53
54
1. Specifications
Power source
Item Specification
24V DC (supplied from main frame), 5V SC (generated by FIN board), SELV (super-low voltage secondary power supply)
Item
No. of sheets which can be stitched
Sizes which can be stitched
Thicknesses which can be stitched
Stitching position
Staple supply
Stitching capacity
Weight
2 to 5 sheets
A3 SEF - B5 SEF / DLT SEF - LT SEF
54g/m
2
-80g/m
2
Specification
1 position (Top Slant)
No
No
Less than 1.4 kg
(not including packaging materials and other items in package)
1200k sheets or 5 years Service life
*1 80g/m
2
or less (paper exceeding 80g/m
2
is calculated by weight)
*2 Up to 1280 mm in SP mode.
Item
Paper size for the finisher upper tray
Specification
A3 SEF, B4 JIS SEF, A4 SEF/LEF B5 JIS SEF/LEF, A5 SEF/LEF,
B6 JIS SEF, A6 SEF, 12 × 18 SEF, 11 × 17 SEF, 11 × 15 SEF,
10 × 14 SEF, 8 1/2 × 14 SEF, 8 1/2 × 13 LEF, 8 1/2 × 11
SEF/LEF, 8 1/4 × 14 SEF, 8 1/4 × 13 SEF, 8 × 13 SEF, 8 × 10
SEF, 5 1/2 × 8 1/2 SEF, 7 1/4 × 10 1/2 SEF/LEF, 8K SEF,
16K SEF/LEF, SRA3 SEF, SRA4 SEF/LEF, 8 1/2 × 13 2/5 LEF, custom size
Option Specifications
Item
Paper weight for the finisher upper tray:
52–169 g/m
2
Specification
(14 lb. Bond–90 lb. Index)
Stack capacity for the finisher upper tray (80 g/m
2
, 20 lb.
Bond):
Paper sizes that can be shifted when delivered to the finisher shift tray:
250 sheets: A4, 81/2 × 11 or smaller
50 sheets: B4 JIS, 81/2 × 14 or larger
Paper size for the finisher shift tray: A3 SEF, B4 JIS SEF, A4 SEF/LEF, B5 JIS/LEF, A5 SEF/LEF, B6
JIS SEF, A6 SEF, 12 × 18 SEF, 11 × 17 SEF, 11 × 15 SEF, 10 ×
14 SEF, 8 1/2 × 14 SEF, 8 1/2 × 13 LEF, 8 1/2 × 11 SEF/
LEF, 8 1/4 × 14 SEF, 8 1/4 × 13 SEF, 8 × 13 SEF, 8 × 10 SEF,
7 1/4 × 10 1/2 SEF/LEF, 5 1/2 × 8 1/2 SEF, 8K SEF, 16K
SEF/LEF, SRA3 SEF, SRA4 SEF/LEF, 8 1/2 × 13 2/5 LEF, custom size
Paper weight for the finisher shift tray:
52–300 g/m
2
(14 lb. Bond–110 lb. Cover)
A3 SEF, A4 SEF/LEF, A5 SEF, B4 JIS SEF, B5 JIS SEF, B6 JIS
SEF, 12 × 18 SEF, 11 × 17 SEF, 11 × 15 SEF, 10 × 14 SEF, 8
1/2 × 14 SEF, 8 1/2 × 13 LEF, 8 1/2 × 11 SEF/LEF, 8 1/4 ×
14 SEF, 8 1/4 × 13 SEF, 8 × 13 SEF, 8 × 10 SEF, 7 1/4 × 10
1/2 SEF/LEF, 5 1/2 × 8 1/2 SEF, 8K SEF, 16K SEF/LEF SRA4
LEF, 8 1/2 × 13 2/5 LEF
52–300 g/m
2
(14 lb. Bond–110 lb. Cover) Paper weight that can be shifted when delivered to the finisher shift tray:
Stack capacity for the finisher shift tray (80 g/m
2
, 20 lb. Bond):
Staple paper size:
Staple paper weight:
1,000 sheets: A4, 81/2 × 14 or smaller
500 sheets: B4 JIS, 81/2 × 14 or larger
A3 SEF, B4 JIS SEF, A4 SEF/LEF, B5 JIS SEF/LEF, 11 × 17 SEF,
11 × 15 SEF, 10 × 14 SEF, 8 1/2 × 14 SEF, 8 1/2 × 11 SEF/
LEF, 7 1/4 × 10 1/2 SEF/LEF, 8 × 13 SEF, 8B 1/2 × 13 LEF, 8
1/4 × 14 SEF, 8 1/4 × 13 SEF, 8 × 10 SEF, 12 × 18 SEF, 8K
SEF, 16K SEF/LEF, 8 1/2 × 13 2/5 LEF, custom size
52–105 g/m
2
(14-28 lb. Bond)
You can use two sheets of paper weighing up to 216 g/m
2
(80 lb. Cover) per set as cover sheets.
55
56
1. Specifications
Item
Staple capacity (80 g/m
2
, 20 lb.
Bond):
Stack capacity after stapling (80 g/m
2
, 20 lb. Bond):
Staple position:
Saddle stitch paper size:
Saddle stitch paper weight:
Saddle stitch capacity (80 g/m
2
,
20 lb. Bond):
Specification
• Without Mixed Size:
30 sheets:
A3 SEF, B4 JIS SEF, 11 × 17 SEF, 8 1/2 × 14 SEF, 8 × 13
SEF, 8 1/2 × 13 LEF, 8 1/4 × 14 SEF, 8 1/4 × 13 SEF,
11 × 15 SEF, 10 × 14 SEF, 8K SEF, 12 × 18 SEF, 8 1/2 ×
13 2/5 LEF
50 sheets:
A4 SEF/LEF, B5 JIS SEF/LEF, 8 1/2 × 11 SEF/LEF, 8 × 10
SEF, 7 1/4 × 10 1/2 SEF/LEF, 16K SEF/LEF
• With Mixed Size:
22 sheets:
A3 SEF/A4 LEF, B4 JIS SEF/B5 JIS SEF, 11 × 17 SEF/8
1/2 × 11 SEF
• Without Mixed Size:
• 2–9 sheets: 100 sets (A4 LEF, B5 JIS LEF, 8 1/2 × 11
LEF)
• 10–50 sheets: 100–20 sets (A4 LEF, B5 JIS LEF, 8
1/2 × 11 LEF)
• 10–50 sheets: 50–10 sets (A4 SEF, B5 JIS SEF, 8
1/2 × 11 SEF)
• 2–9 sheets: 50 sets (A3 SEF, A4 SEF, B4 JIS SEF, B5
JIS SEF, 11 × 17 SEF, 8 1/2 × 14 SEF, 8 1/2 × 11
SEF)
• 10–30 sheets: 50–10 sets (A3 SEF, B4 JIS SEF, 11 ×
17 SEF, 8 1/2 × 14 SEF)
• With Mixed Size:
• 2–22 sheets: 22 sets (A3 SEF/ A4 LEF, B4 JIS
SEF/B5 JIS SEF, 11 × 17 SEF/8 1/2 × 11 SEF)
3 positions (Top, Bottom, 2 Staples)
A3 SEF, A4 LEF, B4 JIS SEF, B5 JIS LEF, 11 × 17 SEF, 8 1/2 ×
14 SEF, 8 1/2 × 11 LEF, 12 × 18 SEF
52–105 g/m
2
(14–28 lb. Bond)
1 set (15 sheets)
Option Specifications
Item
Stack capacity after saddle stitching (80 g/m
2
, 20 lb. Bond):
Saddle stitch position:
Types of folds:
Half fold paper size:
Half fold paper weight:
Power consumption:
Dimensions (W × D × H):
Weight:
Specification
2–5 sheets: Approx. 20 sets
6–10 sheets: Approx. 10 sets
11–15 sheets: Approx. 7 sets
Center 2 positions
Half Fold
A3 SEF, A4 LEF, B4 JIS SEF, B5 JIS LEF, 11 × 17 SEF, 8 1/2 ×
14 SEF, 8 1/2 × 11 LEF, 12 × 18 SEF, 8 1/2 × 13 2/5 LEF
52–105 g/m
2
(14–28 lb.Bond)
35.4 W (Power is supplied from the main unit.)
• Tray is folded:
575 × 620 × 960 mm (22.6 × 24.5 × 37.8 inches)
• Tray is extended:
658 × 620 × 960 mm (25.9 × 24.5 × 37.8 inches)
Approx. 42 kg (92.6 lb.)
Paper size:
Punch unit type
2 & 4 holes type: 2 holes
2 & 4 holes type: 2 holes
2 & 4 holes type: 4 holes
2 & 4 holes type: 4 holes
4 holes type: 4 holes
Paper size
SEF: A3, B4 JIS, A4, B5 JIS, A5, 11 × 17, 8 1/2 × 14, 8 1/2
× 11, 5 1/2 × 8 1/2, 7 1/4 × 10 1/2, 8 × 13, 8 1/2 × 13,
8 1/4 × 13, 8K, 16K, 8 1/4 × 14, 8 × 10, 11 × 15, 10 × 14
LEF: A4, B5 JIS, A5, 8 1/2 × 11, 7 1/4 × 10 1/2, 16K
SEF: A3, B4 JIS, 11 × 17, 11 × 15, 8K
LEF: A4, B5 JIS, 8 1/2 × 11, 7 1/4 × 10 1/2, 16K
SEF: A3, B4 JIS, A4, B5 JIS, A5, 11 × 17, 8 1/2 × 14, 8 1/2
× 11, 5 1/2 × 8 1/2, 7 1/4 × 10 1/2, 8 × 13, 8 1/2 × 13,
8 1/4 × 13, 8K, 16K, 8 1/4 × 14, 8 × 10, 11 × 15, 10 × 14
57
58
1. Specifications
Punch unit type
4 holes type: 4 holes
2 & 3 holes type: 2 holes
2 & 3 holes type: 2 holes
2 & 3 holes type: 3 holes
2 & 3 holes type: 3 holes
Paper weight:
52–256 g/m
2
(14 lb. Bond–140 lb. Index)
Paper size
LEF: A4, B5 JIS, A5, 8 1/2 × 11, 7 1/4 × 10 1/2, 16K
SEF: A3, B4 JIS, B5 JIS, A5, 11 × 17, 8 1/2 × 14, 8 1/2 ×
11, 5 1/2 × 8 1/2, 7 1/4 × 10 1/2, 8 × 13, 8 1/2 × 13, 8
1/4 × 13, 8K, 16K, 8 1/4 × 14, 8 × 10, 11 × 15, 10 × 14
LEF: A4, B5 JIS, 8 1/2 × 11, 7 1/4 × 10 1/2, 16K
SEF: A3, B4 JIS, 11 × 17, 11 × 15, 10 × 14, 8K
LEF: A4, B5 JIS, 8 1/2 × 11, 7 1/4 × 10 1/2, 16K
Item
Dimensions (W × D × H):
Specification
Main Tray
Tray is folded:
370 × 250 × 70 mm (14.6 × 9.8 × 2.8 inches)
Tray is expanded:
370 × 250 × 250 mm (14.6 × 9.8 × 9.8 inches)
Sub Tray
Tray is folded:
150 × 110 × 15 mm (5.9 × 4.3 × 0.6 inches)
Tray is expanded:
150 × 110 × 100 mm (5.9 × 4.3 × 3.9 inches)
Lock Plate
Locked:
135 × 150 × 25 mm (5.3 × 5.9 × 1.0 inches)
Unlocked:
135 × 220 × 25 mm (5.3 × 8.7 × 1.0 inches)
Weight:
Item
Main Tray: 942 g (2.0 lb.)
Sub Tray: 245 g (0.5 lb.)
Lock Plate: 280 g (0.6 lb.)
Specification
Option Specifications
59
60
1. Specifications
• Yield Parts:
Some of the parts mentioned in these tables have a target yield. However, the total copy/print volume made by the machine will not reach the target yield within the machine's targeted lifetime if the machine is used under the target usage conditions (ACV, color ratio, P/J, and C/O). So, these parts are categorized not as PM parts but as yield parts (EM parts).
Chart: A4 (LT)/5% image coverage ratio
Mode: 2 copies/original (prints/job)
Color ratio: 20%
Environment: Normal temperature and humidity
Yield may change depending on circumstances and print conditions.
Symbol keys: C: Clean, R: Replace, L: Lubricant, I: Inspect
The PM count for the following items is based on sheets of copy paper:
Item
PM
Parts
Cycle EM
Scanner
Exposure glass
Sheet-through exposure glass
-
-
C
300K
C
300K
C
C
Remarks
Clean with a cleaning cloth.
Do not clean with alcohol. Doing so may leave a whitish trace that affects image scanning.
Clean with a cleaning cloth.
Do not clean with alcohol. Doing so may leave a whitish trace that affects image scanning.
PCDU
61
62
2. Preventive Maintenance
PCU(K)
PCU(C,M,Y)
Item
Development unit (K)
Development unit (C,M,Y)
PM
Parts
-
-
Cycle
R
180K
R
120K
R
60K
R
48K
Waste toner bottle
R
100K
EM
-
-
Remarks
PM parts: only for MP C2504
-
-
Target yield (number of sheets) is only a guide and it is possible to collect up to 1,200,000 mg of waste toner. Full detection is a mechanical detection by a feeler. Replace when waste toner bottle full is detected.
Transfer
Image transfer cleaning unit -
Image transfer belt unit
Paper transfer roller unit
Fusing
Fusing sleeve belt unit
Fusing entrance guide plate
Fusing exit guide plate
Stripper plate
-
-
-
-
-
-
R
240K
R
240K
R
240K
R
240K
-
-
-
-
-
-
-
C
C
C
Remove toner deposits
Remove toner deposits
Remove toner deposits
Preventive Maintenance
Item
Pressure roller
Bearing: Pressure roller
Thermopile
Pressure roller gears
Idler gear
Fusing exit roller
Miscellaneous
Ozone filter/Dust filter
Dust shield glass
TM/ID sensor
Paper feed
Registration roller
Registration sensor
Paper dust collection unit
Transport roller
Transport sensor
Feed roller
-
-
-
-
PM
Parts
-
-
Cycle
R
240K
R/L
240K
C
400K
-
-
-
-
-
-
-
-
-
-
-
-
R
300K
-
-
-
-
-
-
-
-
EM Remarks
-
-
C
R
R
C
Lubricate with FLUTORIBO MG
GREASE: 100G
Dry cloth
Replace if worn out
Replace if worn out
Damp cloth
-
C
C
C
C
C
C
C
C
Damp cloth
Damp cloth
Do not use a dry cloth that can cause static electricity.
Damp cloth
Remove toner and paper dust, Dry cloth
Remove toner and paper dust
Damp cloth
Remove toner and paper dust, Dry cloth
Remove toner and paper dust, Dry cloth
63
64
2. Preventive Maintenance
Item
Separation roller
Pick-up roller
Duplex/Bypass/Exit
Duplex entrance sensor
Duplex exit sensor
Duplex transport roller
Duplex exit roller
Duplex entrance roller1, 2
Bypass paper feed roller
Bypass separation roller
Bypass pick-up roller
Bypass transport roller
Reverse roller
Reverse sensor
Paper exit roller
Paper exit sensor
PM
Parts
-
Cycle
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
EM
C
C
Remarks
Remove toner and paper dust, Dry cloth
Remove toner and paper dust, Dry cloth
C
C
C
C
C
C
C
C
C
C
C
C
C
Remove toner and paper dust, Dry cloth
Remove toner and paper dust, Dry cloth
Damp cloth
Damp cloth
Damp cloth
Damp cloth
Damp cloth
Damp cloth
Damp cloth
Damp cloth
Remove toner and paper dust, Dry cloth
Damp cloth
Remove toner and paper dust, Dry cloth
Preventive Maintenance
Item
Pick-up roller
Feed belt
Separation roller
Sensors
Platen sheet
Other rollers
Scanner guide plate
Item
Pick-up roller
Feed belt
Separation roller
CIS (Glass area)
Sensors
Gears
Cycle
R
120K
R
120K
R
120K
-
-
-
-
C
C
C
C
C
EM
C
C
Remarks
Wipe with a cloth dampened with ethyl alcohol.
Wipe with a cloth dampened with ethyl alcohol or water.
Wipe with a cloth dampened with ethyl alcohol.
Clean with a blower brush.
Wipe with a cloth dampened with ethyl alcohol.
Cycle
R
120K
R
120K
R
120K
-
-
C
L
EM
C
C
C
C
Remarks
Wipe with a cloth dampened with ethyl alcohol.
Wipe with a cloth dampened with ethyl alcohol or water.
Wipe with a cloth dampened with ethyl alcohol.
Clean with a cleaning cloth.
Do not clean with alcohol. Doing so may leave a whitish trace that affects image scanning.
Clean with a blower brush.
Lubricate with Silicone Grease G-501 when noise occurred.
65
66
2. Preventive Maintenance
Platen sheet
Other rollers
Item
Scanner guide plate
Cycle
-
-
-
EM
C
C
C
Remarks
Wipe with a cloth dampened with ethyl alcohol.
Item
Paper feed roller
Pick-up roller
Separation roller
Relay rollers
Bottom plate pad
Sensors
EM
C
C
C
C
C
C
Remarks
Wipe with a cloth dampened with ethyl alcohol.
Wipe with a cloth dampened with ethyl alcohol.
Wipe with a cloth dampened with ethyl alcohol.
Wipe with a cloth dampened with ethyl alcohol.
Remove dust with a dry cloth.
Remove dust with a dry cloth.
Rollers
Copy tray
Sensors
Item
Item
Rollers
EM
C
C
C
Remarks
Wipe with a cloth dampened with ethyl alcohol.
Clean with a damp cloth, and then wipe with a dry cloth.
Clean with a blower brush.
EM
C
Remarks
Wipe with a cloth dampened with ethyl alcohol.
Preventive Maintenance
Item
Exit Tray
EM
C
Remarks
Clean with a damp cloth, and then wipe with a dry cloth.
Item
Rollers
Sensors
EM
C
C
Remarks
Wipe with a cloth dampened with ethyl alcohol.
Remove dust with a dry cloth.
Item
Rollers
Quenching brush
Sensors
Cycle
-
-
-
EM
C
C
C
Stapler (Corner)
Booklet Stapler
R
4000K
C
C
Remarks
Wipe with a cloth dampened with ethyl alcohol.
Clean with a dry cloth if dirt adheres to it.
Clean with a blower brush.
Replace when the staple counter in the logging data reaches 500k.
Staple a few times for a test after replacement.
Replace when the staple counter in the logging data reaches 200k.
Punch
Punch waste
R
4000K
R
3000K
C
300K
C
C
Remove paper dust in the transport unit.
Discard punch waste when hopper full is detected.
67
68
2. Preventive Maintenance
Item
Rollers
Sensors
Stapler
EM
C
C
R
Remarks
Wipe with a cloth dampened with ethyl alcohol.
Clean with a blower brush.
Replace when the staple counter in the logging data reaches 200k.
Item
Rollers
Sensors
Stapler
EM
C
C
R
Remarks
Wipe with a cloth dampened with ethyl alcohol.
Clean with a blower brush.
Replace when the staple counter in the logging data reaches 200k.
1001 [Leading Edge Registration]
1-001-001 Tray1: Thin
1-001-002 Tray1: Plain
1-001-003 Tray1: Mid-thick
1-001-004 Tray1: Thick 1
1-001-005 Tray1: Thick 2
1-001-006 Tray1: Thick 3
1-001-007 Tray1: Thick 4
1-001-008 Tray2/3/4/5/LCT: Thin
1-001-009 Tray2/3/4/5/LCT: Plain
1-001-010 Tray2/3/4/5/LCT: Mid-thick
1-001-011 Tray2/3/4/5/LCT: Thick 1
1-001-012 Tray2/3/4/5/LCT: Thick 2
1-001-013 Tray2/3/4/5/LCT: Thick 3
1-001-014 Tray2/3/4/5/LCT: Thick 4
1-001-015 By-pass: Thin
1-001-016 By-pass: Plain
1-001-017 By-pass: Mid-thick
1-001-018 By-pass: Thick 1
1-001-019 By-pass: Thick 2
1-001-020 By-pass: Thick 3
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
69
70
3. Engine SP Mode Tables
1-001-021 By-pass: Thick 4
1-001-022 Duplex: Thin
1-001-023 Duplex: Plain
1-001-024 Duplex: Mid-thick
1-001-025 Duplex: Thick 1
1-001-026 Duplex: Thick 2
1-001-027 Duplex: Thick 3
1-001-028 Tray1: Thin:1200
1-001-029 Tray1: Plain:1200
1-001-030 Tray1: Mid-thick:1200
1-001-031 Tray1: Thick 1:1200
1-001-032 Tray1: Thick 2:1200
1-001-033 Tray1: Thick 3:1200
1-001-034 Tray1: Thick 4:1200
1-001-035 Tray2/3/4/5/LCT: Thin:1200
1-001-036 Tray2/3/4/5/LCT: Plain:1200
1-001-037 Tray2/3/4/5/LCT: Mid-thick:
1200
1-001-038 Tray2/3/4/5/LCT: Thick 1:1200
1-001-039 Tray2/3/4/5/LCT: Thick 2:1200
1-001-040 Tray2/3/4/5/LCT: Thick 3:1200
1-001-041 Tray2/3/4/5/LCT: Thick 4:1200
1-001-042 By-pass: Thin:1200
1-001-043 By-pass: Plain:1200
1-001-044 By-pass: Mid-thick:1200
1-001-045 By-pass: Thick 1:1200
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
Engine SP Tables - SP1000-1
1-001-046 By-pass: Thick 2:1200
1-001-047 By-pass: Thick 3:1200
1-001-048 By-pass: Thick 4:1200
1-001-049 Duplex: Thin:1200
1-001-050 Duplex: Plain:1200
1-001-051 Duplex: Mid-thick:1200
1-001-052 Duplex: Thick 1:1200
1-001-053 Duplex: Thick 2:1200
1-001-054 Duplex: Thick 3:1200
1002 [Side-to-Side Registration]
1-002-001 By-pass Tray
1-002-002 Paper Tray 1
1-002-003 Paper Tray 2
1-002-004 Paper Tray 3
1-002-005 Paper Tray 4
1-002-006 Duplex
1-002-007 Large Capacity Tray
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
*ENG [-9 to 9 / 0 / 0.1mm/step]
ENG [-4 to 4 / 0 / 0.1mm/step]
ENG [-4 to 4 / 0 / 0.1mm/step]
ENG [-4 to 4 / 0 / 0.1mm/step]
ENG [-4 to 4 / 0 / 0.1mm/step]
ENG [-4 to 4 / 0 / 0.1mm/step]
*ENG [-4 to 4 / 0 / 0.1mm/step]
*ENG [-4 to 4 / 0 / 0.1mm/step]
1003 [Paper Buckle]
1-003-001 Paper Tray1: Thin
1-003-002 Paper Tray1: Plain
1-003-003 Paper Tray 1: Mid-thick
1-003-004 Paper Tray1: Thick1
*ENG [-4 to 5 / 0 / 0.1mm/step]
*ENG [-4 to 5 / 0 / 0.1mm/step]
*ENG [-4 to 5 / 0 / 0.1mm/step]
*ENG [-4 to 5 / -3.5 / 0.1mm/step]
1-003-005 Tray2/3/4/5/LCT: Thin
1-003-006 Tray2/3/4/5/LCT: Plain
*ENG [-4 to 5 / 0 / 0.1mm/step]
*ENG [-4 to 5 / 0 / 0.1mm/step]
1-003-007 Tray 2/3/4/5/LCT: Mid-thick *ENG [-4 to 5 / 0 / 0.1mm/step]
71
72
3. Engine SP Mode Tables
1-003-008 Tray2/3/4/5/LCT: Thick 1
1-003-009 By-pass: Thin
1-003-010 By-pass: Plain
1-003-011 By-pass: Mid-thick
1-003-012 By-pass:Thick1
1-003-013 Duplex:Thin
1-003-014 Duplex:Plain
*ENG [-4 to 5 / -3.5 / 0.1mm/step]
*ENG [-4 to 5 / 0 / 0.1mm/step]
*ENG [-4 to 5 / 0 / 0.1mm/step]
*ENG [-4 to 5 / 0 / 0.1mm/step]
*ENG [-4 to 5 / -3 / 0.1mm/step]
*ENG [-4 to 5 / -1.5 / 0.1mm/step]
*ENG [-4 to 5 / -1.5 / 0.1mm/step]
1-003-015 Duplex: Mid-thick
1-003-016 Duplex:Thick1
1-003-017 Paper Tray1: Thin:1200
1-003-018 Paper Tray1: Plain:1200
*ENG [-4 to 5 / -1.5 / 0.1mm/step]
*ENG [-4 to 5 / -3.5 / 0.1mm/step]
*ENG [-4 to 5 / 0 / 0.1mm/step]
*ENG [-4 to 5 / 0 / 0.1mm/step]
1-003-019 Paper Tray 1: Mid-thick:1200 *ENG [-4 to 5 / 0 / 0.1mm/step]
1-003-020 Paper Tray1: Thick1:1200 *ENG [-4 to 5 / -3.5 / 0.1mm/step]
1-003-021 Tray2/3/4/5/LCT: Thin:1200 *ENG [-4 to 5 / 0 / 0.1mm/step]
1-003-022 Tray2/3/4/5/LCT: Plain:
1200
*ENG [-4 to 5 / 0 / 0.1mm/step]
1-003-023 Tray2/3/4/5/LCT: Mid:1200 *ENG [-4 to 5 / 0 / 0.1mm/step]
1-003-024
Tray2/3/4/5/LCT: Thick
1:1200
1-003-025 By-pass: Thin:1200
1-003-026 By-pass: Plain:1200
1-003-027 By-pass: Mid-thick:1200
*ENG
[-4 to 5 / -3.5 / 0.1mm/step]
*ENG [-4 to 5 / 0 / 0.1mm/step]
*ENG [-4 to 5 / 0 / 0.1mm/step]
1-003-028 By-pass:Thick1:1200
1-003-029 Duplex:Thin:1200
*ENG [-4 to 5 / 0 / 0.1mm/step]
*ENG [-4 to 5 / -3 / 0.1mm/step]
*ENG [-4 to 5 / -1.5 / 0.1mm/step]
1-003-030 Duplex:Plain:1200
1-003-031 Duplex: Mid-thick:1200
*ENG [-4 to 5 / -1.5 / 0.1mm/step]
*ENG [-4 to 5 / -1.5 / 0.1mm/step]
Engine SP Tables - SP1000-1
1-003-032 Duplex:Thick1:1200
1007 [By-Pass Size Detection]
1-007-001 Switch LT SEF/LG SEF
*ENG [-4 to 5 / -3.5 / 0.1mm/step]
1-007-002 By-Pass Jam Detection Set
*ENG [0 or 1 / 0 / 1/step]
0:OFF
1:ON
*ENG [0 or 1 / 0 / 1/step]
0: Normal Detection
1: Simple Detection
1009 [Initial Operation Setting]
1-009-001 Registration Gear Backlash Cut *ENG [0 to 1 / 0 / 1/step]
1009 [Operation Setting]
1-009-002 Paper Exit Speed
1009 [Pickup SOL Separate Setting]
*ENG [0 to 1 / 1 / 1/step]
1-009-003 Paper Tray1: Thin
1-009-004 Paper Tray1: Plain
1-009-005 Paper Tray1: Thick
1-009-006 Paper Tray2: Thin
1-009-007 Paper Tray2: Plain
1-009-008 Paper Tray2: Thick
*ENG [0 to 1 / 1 / 1/step]
*ENG [0 to 1 / 1 / 1/step]
*ENG [0 to 1 / 1 / 1/step]
*ENG [0 to 1 / 1 / 1/step]
*ENG [0 to 1 / 1 / 1/step]
*ENG [0 to 1 / 1 / 1/step]
1-009-009 Paper Tray3: Thin
1-009-010 Paper Tray3: Plain
1-009-011 Paper Tray3: Thick
1-009-012 Paper Tray4: Thin
1-009-013 Paper Tray4: Plain
1-009-014 Paper Tray4: Thick
*ENG [0 to 1 / 1 / 1/step]
*ENG [0 to 1 / 1 / 1/step]
*ENG [0 to 1 / 1 / 1/step]
*ENG [0 to 1 / 1 / 1/step]
*ENG [0 to 1 / 1 / 1/step]
*ENG [0 to 1 / 1 / 1/step]
73
74
3. Engine SP Mode Tables
1-009-015 Paper LCT: Thin
1-009-016 Paper LCT: Plain
1-009-017 Paper LCT: Thick
1101 [Operation Setting]
1-009-018 Pre-rotation Start Temp.
*ENG [0 to 1 / 1 / 1/step]
*ENG [0 to 1 / 1 / 1/step]
*ENG [0 to 1 / 1 / 1/step]
*ENG [0 to 3 / 1 / 1/step]
1101 [Reload Permit Setting]
1-101-001 Pre-rotation Start Temp.
1-101-002 Reload Target Temp.:Center
1-101-003 Reload Target Temp.:Press
1-101-004 Temp.:Delta:Cold:Center
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 190 / 114 / 1deg/step]
*ENG [0 to 200 / 120 / 1deg/step]
1-101-005 Temp.:Delta:Cold:End
*ENG [4 to 200 / * / 1deg/step]
*NA: 27, EU: 31, Asia: 31, CHN: 31,
TWN: 27, KOR: 31
*ENG [4 to 200 / * / 1deg/step]
*NA: 27, EU: 31, Asia: 31, CHN: 31,
TWN 27, KOR: 31
*ENG [4 to 200 / 110 / 1deg/step]
*ENG [0 to 100 / 15 / 0.1sec/step]
1-101-006 Temp.:Delta:Cold:Press
1-101-007 Forced Reload Time:Cold
1-101-008 Temp.:Delta:Low Power:Center *ENG [4 to 200 / 6 / 1deg/step]
1-101-009 Temp.:Delta:Low Power:End *ENG [4 to 200 / 6 / 1deg/step]
1-101-010 Temp.:Delta:Low Power:Press *ENG [4 to 200 / 110 / 1deg/step]
1-101-011 Forced Reload Time:Low Power *ENG [0 to 100 / 15 / 0.1sec/step]
1-101-012 Temp.:Delta:Hot:Center
1-101-013 Temp.:Delta:Hot:End
1-101-014 Temp.:Delta:Hot:Press
*ENG [4 to 200 / 6 / 1deg/step]
*ENG [4 to 200 / 6 / 1deg/step]
*ENG [4 to 200 / 110 / 1deg/step]
Engine SP Tables - SP1000-1
1-101-015 Forced Reload Time:Hot
1-101-016 Temp.:Delta:Cold:BW1/2:Cent er
1-101-102 Reload Target
Temp.:Press:Energy Saving
1-101-103 Temp.:Delta:Cold:Energy
Saving:Center
*ENG [0 to 100 / 15 / 0.1sec/step]
*ENG [4 to 200 / * / 1deg/step]
*NA: 42, EU: 46, Asia: 46, CHN: 46,
TWN: 42, KOR: 46
1-101-017 Temp.:Delta:Cold:BW1/2:End *ENG [4 to 200 / * / 1deg/step]
*NA: 42, EU: 46, Asia: 46, CHN: 46,
TWN: 42, KOR: 46
*ENG [4 to 200 / 110 / 1deg/step] 1-101-018 Temp.:Delta:Cold:BW1/2:Pres s
1-101-019 Forced Reload
Time:Cold:BW1/2
*ENG [0 to 100 / 15 / 0.1sec/step]
1-101-101 Reload Target
Temp.:Center:Energy Saving
*ENG [0 to 200 / * / 1deg/step]
*NA: 116, EU: 114, Asia: 114, CHN:
114, TWN: 116, KOR: 114
*ENG [0 to 200 / 120 / 1deg/step]
1-101-104 Temp.:Delta:Cold:Energy
Saving:End
*ENG [0 to 200 / * / 1deg/step]
*NA: 34, EU: 42, Asia: 42, CHN: 42,
TWN: 34, KOR: 42
*ENG [0 to 200 / * / 1deg/step]
*NA: 34, EU: 42, Asia: 42, CHN: 42,
TWN: 34, KOR: 42
1-101-105 Temp.:Delta:Cold:Energy
Saving:Press
1-101-106 Forced Reload
Time:Cold:Energy Saving
*ENG [4 to 200 / 100 / 1deg/step]
*ENG [0 to 100 / 30 / 0.1sec/step]
1-101-151 Temp.:Delta:Low Temp.:Center *ENG [4 to 200 / 6 / 1deg/step]
1-101-152 Temp.:Delta:Low Temp.:End
1-101-153 Temp.:Delta:Low Temp.:Press
*ENG [4 to 200 / 6 / 1deg/step]
*ENG [4 to 200 / 70 / 1deg/step]
1-101-154 Forced Reload Time:Low Temp. *ENG [0 to 100 / 35 / 0.1sec/step]
75
76
3. Engine SP Mode Tables
1-101-201 Temp.:Delta:Cold:Center:FINless/ADF-less
1-101-202 Temp.:Delta:Cold:End:FINless/ADF-less
1-101-212 Temp.:Delta:Cold:End:FINless/ADF-attached
*ENG [4 to 200 / * / 1deg/step]
*NA: 30, EU: 34, Asia: 34, CHN: 34,
TWN: 30, KOR: 34
*ENG [4 to 200 / * / 1deg/step]
*NA: 30, EU: 34, Asia: 34, CHN: 34,
TWN: 30, KOR: 34
*ENG [4 to 200 / 110 / 1deg/step] 1-101-203 Temp.:Delta:Cold:Press:FINless/ADF-less
1-101-204 Forced Reload Time:Cold:FINless/ADF-less
1-101-211 Temp:Delta:Cold:Center:FINless/ADF-attached
*ENG [0 to 100 / 15 / 0.1sec/step]
*ENG [4 to 200 / * / 1deg/step]
*NA: 30, EU: 34, Asia: 34, CHN: 34,
TWN: 30, KOR: 34
*ENG [4 to 200 / * / 1deg/step]
*NA: 30, EU: 34, Asia: 34, CHN: 34,
TWN: 30, KOR: 34
*ENG [4 to 200 / 110 / 1deg/step] 1-101-213 Temp.:Delta:Cold:Press:FINless/ADF-attached
1-101-214 ForcedReloadTime:Cold:FINless/ADF-attached
*ENG [0 to 100 / 15 / 0.1sec/step]
1102 [Feed Permit Setting]
1-102-001 Temp.:Lower Delta:Center
1-102-002 Temp.:Lower Delta:End
1-102-003 Temp.:Upper Delta:Center
1-102-004 Temp.:Upper Delta:End
1-102-005 Temp.:Lower Delta:Press
*ENG [0 to 200 / * / 1deg/step]
*NA: 33, EU: 38, Asia: 38, CHN: 38,
TWN: 33, KOR: 38
*ENG [0 to 200 / * / 1deg/step]
*NA: 33, EU: 38, Asia: 38, CHN: 38,
TWN: 33, KOR: 38
*ENG [0 to 200 / 40 / 1deg/step]
*ENG [0 to 200 / 40 / 1deg/step]
*ENG [0 to 200 / 90 / 1deg/step]
Engine SP Tables - SP1000-1
1-102-006 Rotation Time *ENG [0 to 100 / 0.65 / 0.01sec/step]
1-102-007 Temp.:Lower Delta:Center:Sp.1 *ENG [0 to 200 / 5 / 1deg/step]
1-102-008 Temp.:Lower Delta:End:Sp.1
*ENG [0 to 200 / 5 / 1deg/step]
1-102-009 Temp.:Upper Delta:Center:Sp.1 *ENG [0 to 200 / 30 / 1deg/step]
1-102-010 Temp.:Upper Delta:End:Sp.1
*ENG [0 to 200 / 30 / 1deg/step]
1-102-011 Temp.:Lower Delta:Press:Sp.1
*ENG [0 to 200 / 45 / 1deg/step]
1-102-012 Rotation Time:Sp.1
*ENG [0 to 200 / 0.65 / 0.01sec/step]
1-102-013 Temp.:Lower Delta:Center:Sp.2 *ENG [0 to 100 / 0 / 0.01sec/step]
1-102-014 Temp.:Lower Delta:End:Sp.2
*ENG [0 to 200 / 5 / 1deg/step]
1-102-015 Temp.:Upper Delta:Center:Sp.2 *ENG [0 to 200 / 15 / 1deg/step]
1-102-016 Temp.:Upper Delta:End:Sp.2
*ENG [0 to 200 / 15 / 1deg/step]
1-102-017 Temp.:Lower Delta:Press:Sp.2
*ENG [0 to 200 / 100 / 1deg/step]
1-102-018 Rotation Time:Sp2 *ENG [0 to 100 / 0.65 / 0.01sec/step]
1-102-019 Feed Permit Time
1-102-020 Temp.:Lower Delta:Center
*ENG [0 to 200 / 60 / 1sec/step]
*ENG [0 to 200 / 40 / 1deg/step]
1-102-021 Temp.:Lower Delta:End
1-102-022 Temp.:Upper Delta:Center
1-102-023 Temp.:Upper Delta:End
1-102-024 Temp.:Lower Delta:Press
1-102-025 Temp.:Lower Delta:Press
*ENG [0 to 200 / 40 / 1deg/step]
*ENG [0 to 200 / 30 / 1deg/step]
*ENG [0 to 200 / 30 / 1deg/step]
*ENG [0 to 200 / 38 / 1deg/step]
*ENG [0 to 200 / 53 / 1deg/step]
1-102-026 Rotation Time
1-102-027 Temp.:Lower Delta:Center
1-102-028 Temp.:Lower Delta:End
1-102-029 Temp.:Upper Delta:Center
1-102-030 Temp.:Upper Delta:End
1-102-031 Temp.:Lower Delta:Press
*ENG [0 to 100 / 0.65 / 0.01sec/step]
*ENG [0 to 200 / 5 / 1deg/step]
*ENG [0 to 200 / 5 / 1deg/step]
*ENG [0 to 200 / 30 / 1deg/step]
*ENG [0 to 200 / 30 / 1deg/step]
*ENG [0 to 200 / 34 / 1deg/step]
77
78
3. Engine SP Mode Tables
1-102-032 Temp.:Lower Delta:Press
1-102-033 Rotation Time
1-102-034 Temp.:Lower Delta:Center
1-102-035 Temp.:Lower Delta:End
1-102-036 Temp.:Upper Delta:Center
1-102-037 Temp.:Upper Delta:End
1-102-038 Temp.:Lower Delta:Press
1-102-039 Temp.:Lower Delta:Press
1-102-040 Rotation Time
1-102-041 Judgment Power A
*ENG [0 to 200 / 49 / 1deg/step]
*ENG [0 to 100 / 0.65 / 0.01sec/step]
*ENG [0 to 200 / 5 / 1deg/step]
*ENG [0 to 200 / 5 / 1deg/step]
*ENG [0 to 200 / 15 / 1deg/step]
*ENG [0 to 200 / 15 / 1deg/step]
*ENG [0 to 200 / 100 / 1deg/step]
*ENG [0 to 200 / 100 / 1deg/step]
*ENG [0 to 100 / 0.65 / 0.01sec/step]
*ENG [0 to 2000 / * / 1W/step]
*NA: 1304, EU: 1429, Asia: 1429,
CHN: 1429, TWN: 1304, KOR: 1429
*ENG [0 to 200 / 49 / 1deg/step] 1-102-042 Temp.:Lower
Delta:Center:Power A
1-102-043 Temp.:Lower Delta::Power A
1-102-044 Temp.:Upper
Delta:Center:Power A
1-102-045 Temp.:Upper Delta:End:Power
A
1-102-046 Temp.:Lower Delta:Press:Power
A
1-102-047 Rotation Time:Power A
1-102-051 Judgment Power B
*ENG [0 to 200 / 49 / 1deg/step]
*ENG [0 to 200 / 40 / 1deg/step]
*ENG [0 to 200 / 40 / 1deg/step]
*ENG [0 to 200 / 90 / 1deg/step]
*ENG [0 to 100 / 0.65 / 0.01sec/step]
*ENG [0 to 2000 / * / 1W/step]
*NA: 1284, EU: 1409, Asia: 1409,
CHN: 1409, TWN: 1284, KOR: 1409
*ENG [0 to 200 / 49 / 1deg/step] 1-102-052 Temp.:Lower
Delta:Center:Power B
1-102-053 Temp.:Lower Delta:End:Power
B
*ENG [0 to 200 / 49 / 1deg/step]
Engine SP Tables - SP1000-1
1-102-054 Temp.:Upper
Delta:Center:Power B
1-102-055 Temp.:Upper Delta:End:Power
B
*ENG [0 to 200 / 40 / 1deg/step]
*ENG [0 to 200 / 40 / 1deg/step]
1-102-056 Temp.:Lower Delta:Press:Power
B
1-102-057 Rotation Time:Power B
*ENG [0 to 200 / 90 / 1deg/step]
*ENG [0 to 100 / 0.65 / 0.01sec/step]
1-102-060 Waiting Time: Stabilize Temp.
*ENG [0 to 10000 / 0 / 1msec/step]
1-102-070 Timeout: Cold: Normal *ENG [0 to 20000 / 4000 / 1msec/step]
1-102-071 Timeout: Hot: Normal
1-102-072 Timeout: Cold: Power 1
1-102-073 Timeout: Hot: Power 1
1-102-074 Timeout: Cold: Power 2
1-102-075 Timeout: Hot: Power 2
1-102-076 Timeout: 10sec: 11
1-102-077 Timeout: 10sec: 15
1-102-078 Timeout: 10sec: 16
*ENG [0 to 20000 / 4000 / 1msec/step]
*ENG [0 to 20000 / 4000 / 1msec/step]
*ENG [0 to 20000 / 4000 / 1msec/step]
*ENG [0 to 20000 / 4000 / 1msec/step]
*ENG [0 to 20000 / 4000 / 1msec/step]
*ENG [0 to 20000 / 4000 / 1msec/step]
*ENG [0 to 20000 / 4000 / 1msec/step]
*ENG [0 to 20000 / 4000 / 1msec/step]
1-102-101 Temp.:Lower Delta:Press0
1-102-102 Temp.:Lower Delta:Press10
1-102-103 Temp.:Lower Delta:Press1
1-102-104 Temp.:Lower Delta:Press2
1-102-105 Temp.:Lower Delta:Press3
1-102-106 Temp.:Lower Delta:Press13
1-102-107 Temp.:Lower Delta:Press4
1-102-108 Temp.:Lower Delta:Press14
1-102-109 Temp.:Lower Delta:Press5
1-102-110 Temp.:Lower Delta:Press6
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 17 / 1deg/step]
*ENG [0 to 200 / 17 / 1deg/step]
79
80
3. Engine SP Mode Tables
1-102-111 Temp.:Lower Delta:Press7
1-102-112 Temp.:Lower Delta:Press11
1-102-113 Temp.:Lower Delta:Press15
1-102-114 Temp.:Lower Delta:Press16
1-102-121 Timeout:Press0
1-102-122 Timeout:Press10
1-102-123 Timeout:Press1
1-102-124 Timeout:Press2
1-102-125 Timeout:Press3
1-102-126 Timeout:Press13
1-102-127 Timeout:Press4
1-102-128 Timeout:Press14
1-102-129 Timeout:Press5
1-102-130 Timeout:Press6
1-102-131 Timeout:Press7
1-102-132 Timeout: Press: 11
1-102-133 Timeout: Press: 15
1-102-134 Timeout: Press: 16
1105 [Print Target Temp.]
1-105-001 Plain1:FC:Center
1-105-002 Plain1:FC:Press
1-105-003 Plain1:BW:Center
*ENG [0 to 200 / 13 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 60000 / 5000 / 1msec/step]
*ENG [0 to 60000 / 5000 / 1msec/step]
*ENG [0 to 60000 / 3000 / 1msec/step]
*ENG [0 to 60000 / 0 / 1msec/step]
*ENG [0 to 60000 / 0 / 1msec/step]
*ENG [0 to 60000 / 0 / 1msec/step]
*ENG [100 to 180 / * / 1deg/step]
*MP C2004: 126
*MP C2504: 123
*ENG [0 to 200 / 122 / 1deg/step]
*ENG [100 to 180 / * / 1deg/step]
*MP C2004: 123
*MP C2504: 120
1-105-004 Plain1:BW:Press
1-105-005 Plain2:FC:Center
1-105-006 Plain2:FC:Press
1-105-007 Plain2:BW:Center
1-105-008 Plain2:BW:Press
1-105-009 Thin:FC:Center
1-105-010 Thin:FC:Press
1-105-011 Thin:BW:Center
1-105-012 Thin:BW:Press
1-105-013 M-thick:FC:Center
1-105-014 M-thick:FC:Press
1-105-015 M-thick:BW:Center
1-105-016 M-thick:BW:Press
1-105-017 Thick1:FC:Center
1-105-018 Thick1:FC:Press
1-105-019 Thick1:BW:Center
1-105-020 Thick1:BW:Press
1-105-021 Thick2:FC:Center
1-105-022 Thick2:FC:Press
Engine SP Tables - SP1000-1
*ENG [0 to 200 / 122 / 1deg/step]
*ENG [100 to 180 / * / 1deg/step]
*MP C2004: 128
*MP C2504: 122
*ENG [0 to 200 / 122 / 1deg/step]
*ENG [100 to 180 / * / 1deg/step]
*MP C2004: 128
*MP C2504: 122
*ENG [0 to 200 / 122 / 1deg/step]
*ENG [100 to 180 / * / 1deg/step]
*MP C2004: 121
*MP C2504: 118
*ENG [0 to 200 / 121 / 1deg/step]
*ENG [100 to 180 / * / 1deg/step]
*MP C2004: 121
*MP C2504: 118
*ENG [0 to 200 / 121 / 1deg/step]
*ENG [100 to 180 / 136 / 1deg/step]
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 136 / 1deg/step]
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 127 / 1deg/step]
*ENG [0 to 200 / 120 / 1deg/step]
*ENG [100 to 180 / 127 / 1deg/step]
*ENG [0 to 200 / 120 / 1deg/step]
*ENG [100 to 180 / 132 / 1deg/step]
*ENG [0 to 200 / 120 / 1deg/step]
81
82
3. Engine SP Mode Tables
1-105-023 Thick2:BW:Center
1-105-024 Thick2:BW:Press
1-105-025 Thick3:FC:Center
1-105-026 Thick3:FC:Press
1-105-027 Thick3:BW:Center
1-105-028 Thick3:BW:Press
1-105-029 Special1:FC:Center
1-105-030 Special1:FC:Press
1-105-031 Special1:BW:Center
1-105-032 Special1:BW:Press
1-105-033 Special2:FC:Center
1-105-034 Special2:FC:Press
1-105-035 Special2:BW:Center
1-105-036 Special2:BW:Press
1-105-037 Special3:FC:Center
1-105-038 Special3:FC:Press
1-105-039 Special3:BW:Center
1-105-040 Special3:BW:Press
1-105-041 Envelop:Center
*ENG [100 to 180 / 132 / 1deg/step]
*ENG [0 to 200 / 120 / 1deg/step]
*ENG [100 to 180 / 137 / 1deg/step]
*ENG [0 to 200 / 120 / 1deg/step]
*ENG [100 to 180 / 137 / 1deg/step]
*ENG [0 to 200 / 120 / 1deg/step]
*ENG [100 to 180 / * / 1deg/step]
*MP C2004: 126
*MP C2504: 123
*ENG [0 to 200 / 117 / 1deg/step]
*ENG [100 to 180 / * / 1deg/step]
*MP C2004: 123
*MP C2504: 120
*ENG [0 to 200 / 117 / 1deg/step]
*ENG [100 to 180 / * / 1deg/step]
*MP C2004: 131
*MP C2504: 128
*ENG [0 to 200 / 122 / 1deg/step]
*ENG [100 to 180 / * / 1deg/step]
*MP C2004: 128
*MP C2504: 125
*ENG [0 to 200 / 122 / 1deg/step]
*ENG [100 to 180 / 136 / 1deg/step]
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 136 / 1deg/step]
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 142 / 1deg/step]
Engine SP Tables - SP1000-1
1-105-042 Envelop:Press
1-105-051 Special1:FC:Center:Middle
Speed
1-105-052 Special1:FC:Press:Middle
Speed
1-105-053 Special1:BW:Center:Middle
Speed
1-105-054 Special1:BW:Press:Middle
Speed
1-105-055 Special2:FC:Center:Middle
Speed
1-105-056 Special2:FC:Press:Middle
Speed
1-105-057 Special2:BW:Center:Middle
Speed
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 122 / 1deg/step]
*ENG [0 to 200 / 120 / 1deg/step]
*ENG [100 to 180 / 122 / 1deg/step]
*ENG [0 to 200 / 120 / 1deg/step]
*ENG [100 to 180 / 127 / 1deg/step]
*ENG [0 to 200 / 120 / 1deg/step]
*ENG [100 to 180 / 127 / 1deg/step]
1-105-058 Special2:BW:Press:Middle
Speed
1-105-059 Special3:FC:Center:Middle
Speed
1-105-060 Special3:FC:Press:Middle
Speed
1-105-061 Special3:BW:Center:Middle
Speed
*ENG [0 to 200 / 120 / 1deg/step]
*ENG [100 to 180 / 132 / 1deg/step]
*ENG [0 to 200 / 120 / 1deg/step]
*ENG [100 to 180 / 132 / 1deg/step]
1-105-062 Special3:BW:Press:Middle
Speed
1-105-101 Plain1:FC:Center:Low Speed
1-105-102 Plain1:FC:Press:Low Speed
*ENG [0 to 200 / 120 / 1deg/step]
*ENG [100 to 180 / 115 / 1deg/step]
*ENG [0 to 200 / 118 / 1deg/step]
1-105-103 Plain1:BW:Center:Low Speed *ENG [100 to 180 / 115 / 1deg/step]
1-105-104 Plain1:BW:Press:Low Speed *ENG [0 to 200 / 118 / 1deg/step]
1-105-105 Plain2:FC:Center:Low Speed *ENG [100 to 180 / 120 / 1deg/step]
83
84
3. Engine SP Mode Tables
1-105-106 Plain2:FC:Press:Low Speed *ENG [0 to 200 / 118 / 1deg/step]
1-105-107 Plain2:BW:Center:Low Speed *ENG [100 to 180 / 120 / 1deg/step]
1-105-108 Plain2:BW:Press:Low Speed *ENG [0 to 200 / 118 / 1deg/step]
1-105-109 M-thick:FC:Center:Low Speed *ENG [100 to 180 / 122 / 1deg/step]
1-105-110 M-thick:FC:Press:Low Speed *ENG [0 to 200 / 118 / 1deg/step]
1-105-111 M-thick:BW:Center:Low Speed *ENG [100 to 180 / 122 / 1deg/step]
1-105-112 M-thick:BW:Press:Low Speed *ENG [0 to 200 / 118 / 1deg/step]
1-105-113 Thick1:FC:Center:Low Speed
1-105-114 Thick1:FC:Press:Low Speed
*ENG [100 to 180 / 127 / 1deg/step]
*ENG [0 to 200 / 118 / 1deg/step]
1-105-115 Thick1:BW:Center:Low Speed *ENG [100 to 180 / 127 / 1deg/step]
1-105-116 Thick1:BW:Press:Low Speed *ENG [0 to 200 / 118 / 1deg/step]
1-105-117 Special1:FC:Center:Low Speed *ENG [100 to 180 / 122 / 1deg/step]
1-105-118 Special1:FC:Press:Low Speed *ENG [0 to 200 / 118 / 1deg/step]
1-105-119 Special1:BW:Center:Low
Speed
*ENG [100 to 180 / 122 / 1deg/step]
1-105-120 Special1:BW:Press:Low Speed *ENG [0 to 200 / 118 / 1deg/step]
1-105-121 Special2:FC:Center:Low Speed *ENG [100 to 180 / 132 / 1deg/step]
1-105-122 Special2:FC:Press:Low Speed *ENG [0 to 200 / 120 / 1deg/step]
1-105-123 Special2:BW:Center:Low
Speed
*ENG [100 to 180 / 132 / 1deg/step]
1-105-124 Special2:BW:Press:Low Speed *ENG [0 to 200 / 120 / 1deg/step]
1-105-125 Plain1:Glossy:Center *ENG [100 to 180 / 132 / 1deg/step]
1-105-126 Plain1:Glossy:Press
1-105-127 Plain2:Glossy:Center
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 137 / 1deg/step]
1-105-128 Plain2:Glossy:Press
1-105-129 M-thick:Glossy:Center
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 142 / 1deg/step]
Engine SP Tables - SP1000-1
1-105-130 M-thick:Glossy:Press
1-105-131 OHP:Center
1-105-132 OHP:Press
1-105-133 Envelop:Center:Low Speed
1-105-134 Envelop:Press:Low Speed
1-105-135 Thin:FC:Center:Low Speed
1-105-136 Thin:FC:Press:Low Speed
1-105-137 Thin:BW:Center:Low Speed
1-105-138 Thin:BW:Press:Low Speed
1-105-139 Thick4:FC:Center
1-105-140 Thick4:FC:Press
1-105-141 Thick4:BW:Center
1-105-142 Thick4:BW:Press
1-105-143 Postcard:Center
1-105-144 Postcard:Press
1-105-145 Special3:FC:Center:Middle
Speed
1-105-146 Special3:FC:Press:Middle
Speed
1-105-147 Special3:BW:Center:Middle
Speed
1-105-148 Special3:BW:Press:Middle
Speed
1-105-149 Mid Thick:Matte:Center
1-105-150 Mid Thick:Matte:Press
1-105-151 Thick1:Matte:Center
1-105-152 Thick1:Matte:Press
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 160 / 1deg/step]
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 135 / 1deg/step]
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 110 / 1deg/step]
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 110 / 1deg/step]
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 142 / 1deg/step]
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 142 / 1deg/step]
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 124 / 1deg/step]
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 142 / 1deg/step]
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 142 / 1deg/step]
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 136 / 1deg/step]
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 127 / 1deg/step]
*ENG [0 to 200 / 120 / 1deg/step]
85
86
3. Engine SP Mode Tables
1-105-153 Thick2:Matte:Center
1-105-154 Thick2:Matte:Press
1-105-155 Thick3:Matte:Center
*ENG [100 to 180 / 132 / 1deg/step]
*ENG [0 to 200 / 120 / 1deg/step]
*ENG [100 to 180 / 137 / 1deg/step]
1-105-156 Thick3:Matte:Press
1-105-157 Thick4:Matte:Center
*ENG [0 to 200 / 120 / 1deg/step]
*ENG [100 to 180 / 142 / 1deg/step]
1-105-158 Thick4:Matte:Press
1-105-159 Mid Thick:Matte:Center:Low
Speed
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 122 / 1deg/step]
1-105-160 Mid Thick:Matte:Press:Low
Speed
1-105-161 Thick1:Matte:Center:Low
Speed
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 127 / 1deg/step]
1-105-162 Thick1:Matte:Press:Low Speed *ENG [0 to 200 / 118 / 1deg/step]
1-105-163 Mid Thick:Glossy:Center
1-105-164 Mid Thick:Glossy:Press
1-105-165 Thick1:Glossy:Center
1-105-166 Thick1:Glossy:Press
1-105-167 Thick2:Glossy:Center
1-105-168 Thick2:Glossy:Press
1-105-169 Thick3:Glossy:Center
1-105-170 Thick3:Glossy:Press
1-105-171 Thick4:Glossy:Center
1-105-172 Thick4:Glossy:Press
1-105-173 Mid Thick:Glossy:Center:Low
Speed
1-105-174 Mid Thick:Glossy:Press:Low
Speed
*ENG [100 to 180 / 136 / 1deg/step]
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 127 / 1deg/step]
*ENG [0 to 200 / 120 / 1deg/step]
*ENG [100 to 180 / 132 / 1deg/step]
*ENG [0 to 200 / 120 / 1deg/step]
*ENG [100 to 180 / 137 / 1deg/step]
*ENG [0 to 200 / 120 / 1deg/step]
*ENG [100 to 180 / 142 / 1deg/step]
*ENG [0 to 200 / 118 / 1deg/step]
*ENG [100 to 180 / 122 / 1deg/step]
*ENG [0 to 200 / 118 / 1deg/step]
Engine SP Tables - SP1000-1
1-105-175 Thick1:Glossy:Center:Low
Speed
*ENG [100 to 180 / 127 / 1deg/step]
1-105-176 Thick1:Glossy:Press:Low Speed *ENG [0 to 200 / 118 / 1deg/step]
1106 [Fusing Temp. Display]
1-106-001 Heat Center
1-106-002 Heat End
1-106-003 Press Center
1-106-004 Press End
1-106-005 Press End
ENG
ENG
ENG
[-10 to 250 / 0 / 1deg/step]
[-10 to 250 / 0 / 1deg/step]
[-10 to 250 / 0 / 1deg/step]
ENG [-10 to 250 / 0 / 1deg/step]
ENG [-10 to 250 / 0 / 1deg/step]
1107 [Standby Target Temp. Setting]
1-107-001 Stanby/Preheat1:Center
1-107-003 Preheat2:Center
1-107-005 Low Power:Center
1-107-007 Print Ready:Center
1-107-008 Print Ready:Press
1-107-011 Standby Heater Off Time
*ENG [0 to 125 / 90 / 1deg/step]
*ENG [0 to 200 / 90 / 1deg/step]
*ENG [0 to 125 / 60 / 1deg/step]
*ENG [85 to 180 / * / 1deg/step]
*MP C2004: 121
*MP C2504: 118
*ENG [0 to 200 / 120 / 1deg/step]
*ENG [0 to 100 / 0 / 1sec/step]
1108 [After Reload/Job Target Temp.]
1-108-001 Center *ENG [85 to 200 / * / 1deg/step]
*MP C2004: 121
*MP C2504: 118
1-108-002 Press
1-108-011 Center:Energy Saving
*ENG [0 to 200 / 120 / 1deg/step]
*ENG [85 to 200 / * / 1deg/step]
*NA: 116, EU: 114, Asia: 114, CHN:
114, TWN: 116, KOR: 114
87
88
3. Engine SP Mode Tables
1-108-012 Press:Energy Saving *ENG [0 to 200 / 120 / 1deg/step]
1111 [Environment Correction:Fusing]
1-111-001 Temp.: Threshold: Low
1-111-002 Temp.: Threshold: High
1-111-003 Low Temp. Correction
*ENG [0 to 100 / 15 / 1deg/step]
*ENG [0 to 100 / 30 / 1deg/step]
1-111-004 High Temp. Correction
1-111-005 Job Low Temp. Correction
*ENG [0 to 15 / 3 / 1deg/step]
*ENG [0 to 15 / 0 / 1deg/step]
*ENG [0 to 10 / 0.6 / 0.1deg/step]
1-111-006 Job High Temp. Correction *ENG [0 to 100 / 0 / 0.1deg/step]
1-111-007 Job Low Temp. Correction:Sp.
*ENG [0 to 10 / 0.7 / 0.1deg/step]
1-111-008 Job High Temp. Correction:Sp.
*ENG [0 to 100 / 0 / 0.1deg/step]
1-111-011 Standard Environment Temp.
*ENG [10 to 30 / 23 / 1deg/step]
1112 [Image Processing Temp. Correct]
1-112-001 Temp.:Plain:Center:Level1/2 *ENG [-20 to 20 / 0 / 1deg/step]
1-112-002 Temp.:Plain:Center:Energy
Saving
*ENG [-30 to 20 / * / 1deg/step]
*MP C2004:
*NA: -12, EU: -14, Asia: -14, CHN:
-14, TWN: -12, KOR: -14
*MP C2504:
*NA: -9, EU: -11, Asia: -11, CHN: -11,
TWN: -9 , KOR: -11
1113 [Curl Correction]
1-113-001 Execute Pattern
1-113-002 Humidity:Threshold:M-humid
*ENG [0 to 2 / 0 / 1/step]
0: OFF
1: ON(No Decurl)
2: ON
*ENG [0 to 100 / 1 / 1%/step]
Engine SP Tables - SP1000-1
1-113-003 Humidity:Threshold:H-humid
1-113-004 Permit Temp.:Delta:Press:Mhumid
1-113-005 Permit Temp.:Delta:Press:Hhumid
1-113-006 Permit Temp.:Delta:Press:Mhumid:No Decurl
1-113-007 Permit Temp.:Delta:Press:Hhumid:No Decurl
1-113-008 CPM:M-humid
1-113-009 CPM:H-humid
1-113-010 CPM:M-humid:No Decurl
1-113-011 CPM:H-humid:No Decurl
1114 [Heat Storage Status]
1-114-001 Temp.:Threshold:Press
1-114-002 Temp.Threshold:Atmosphere
1-114-003 Temp.:Threshold:CPM Down
1-114-004 Temp.:Threshold:Voltage
Detection
1115 [Target Temp. Correction]
1-115-001 Temp.:Delta:End
1116 [Heat Storage FB Control]
1-116-001 Execution mode
1-116-002 Correction Formula Judge
Temp
1-116-003 Heat Gap Correction Temp
*ENG [0 to 100 / 65 / 1%/step]
*ENG [0 to 200 / 60 / 1deg/step]
*ENG [0 to 200 / 50 / 1deg/step]
*ENG [0 to 200 / 50 / 1deg/step]
*ENG [0 to 200 / 40 / 1deg/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 65 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 65 / 1%/step]
*ENG [0 to 200 / 80 / 1deg/step]
*ENG [0 to 200 / 40 / 1deg/step]
*ENG [0 to 200 / 60 / 1deg/step]
*ENG [0 to 200 / 40 / 1deg/step]
*ENG [-100 to 100 / 0 / 1deg/step]
*ENG [0 to 2 / 2 / 1/step]
*ENG [0 to 200 / 97 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
89
90
3. Engine SP Mode Tables
1-116-011 Time Out
1-116-012 Time Out:Energy Saving
1-116-021 Delay:Standard Speed:FC:1
*ENG [0 to 500 / 10 / 1sec/step]
*ENG [0 to 500 / 10 / 1sec/step]
*ENG [0 to 20000 / 3590 / 1msec/step]
1-116-022 Delay:Standard Speed:BW:1 *ENG [0 to 20000 / 1320 / 1msec/step]
1-116-023 Delay:Mid. Speed:FC:1 *ENG [0 to 20000 / 3590 / 1msec/step]
1-116-024 Delay:Mid. Speed:BW:1
1-116-025 Delay:Low Speed:FC:1
*ENG [0 to 20000 / 1320 / 1msec/step]
*ENG [0 to 20000 / 7180 / 1msec/step]
1-116-026 Delay:Low Speed:BW:1
1-116-031 Delay:Standard Speed:FC:2
*ENG [0 to 20000 / 2640 / 1msec/step]
*ENG [0 to 20000 / 3590 / 1msec/step]
1-116-032 Delay:Standard Speed:BW:2 *ENG [0 to 20000 / 1320 / 1msec/step]
1-116-033 Delay:Mid. Speed:FC:2 *ENG [0 to 20000 / 3590 / 1msec/step]
1-116-034 Delay:Mid. Speed:BW:2
1-116-035 Delay:Low Speed:FC:2
1-116-036 Delay:Low Speed:BW:2
1-116-041 Press Reference Temp.
*ENG [0 to 20000 / 1320 / 1msec/step]
*ENG [0 to 20000 / 7180 / 1msec/step]
*ENG [0 to 20000 / 2640 / 1msec/step]
*ENG [0 to 200 / 86 / 1deg/step]
1-116-042 Temp. Correction Lower Limit
1-116-043 Temp. Correction Upper Limit
1-116-044 Press Reference Temp.:Energy
Saving
1-116-045 Temp. Corr. Lower Limit:Energy
Saving
1-116-046 Temp. Corr. Upper Limit:Energy
Saving
1-116-051 Paper Thickness
Coefficient:Plain1
1-116-052 Paper Thickness
Coefficient:Plain2
*ENG [-30 to 0 / 0 / 1deg/step]
*ENG [0 to 30 / 4 / 1deg/step]
*ENG [0 to 200 / 75 / 1deg/step]
*ENG [-30 to 0 / -1 / 1deg/step]
*ENG [0 to 30 / 0 / 1deg/step]
*ENG [-100 to 100 / * / 1/step]
*MP C2004: -20
*MP C2504: -30
*ENG [-100 to 100 / -40 / 1/step]
Engine SP Tables - SP1000-1
1-116-053 Paper Thickness Coeff.:Thin *ENG [-100 to 100 / * / 1/step]
*MP C2004: -20
*MP C2504: -40
1-116-054 Paper Thickness Coeff.:M-thick *ENG [-100 to 100 / * / 1/step]
*MP C2004: -60
*MP C2504: -50
*ENG [-100 to 100 / 0 / 1/step] 1-116-073 Paper Thickness Coeff.:Low
Speed
1-116-074 Paper Thickness
Coeff.:Plain1/2:Energy Save
*ENG [-100 to 100 / 30 / 1/step]
1117 [Repeat Temp. Correction] DFU
1-117-001 Control Time 1:A3
1-117-002 Control Time 2:A3
1-117-003 Temp.:Center:1:A3
1-117-004 Temp.:End:1:A3
1-117-005 Temp.:Center:2:A3
1-117-006 Temp.:End:2:A3
1-117-011 Control Time 1:DLT
1-117-012 Control Time 2:DLT
1-117-013 Temp.:Center:1:DLT
1-117-014 Temp.:End:1:DLT
1-117-015 Temp.:Center:2:DLT
1-117-016 Temp.:End:2:DLT
1-117-021 Control Time 1:B4
1-117-022 Control Time 2:B4
1-117-023 Temp.:Center:1:B4
1-117-024 Temp.:End:1:B4
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [0 to 300 / 4 / 1sec/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 5 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [0 to 300 / 10 / 1sec/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 25 / 1deg/step]
91
92
3. Engine SP Mode Tables
1-117-025 Temp.:Center:2:B4
1-117-026 Temp.:End:2:B4
1-117-031 Control Time 1:LT
1-117-032 Control Time 2:LT
1-117-033 Temp.:Center:1:LT
1-117-034 Temp.:End:1:LT
1-117-035 Temp.:Center:2:LT
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 25 / 1deg/step]
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [-30 to 30 / 6 / 1deg/step]
*ENG [-30 to 30 / 21 / 1deg/step]
*ENG [-30 to 30 / 6 / 1deg/step]
1-117-036 Temp.:End:2:LT *ENG [-30 to 30 / 21 / 1deg/step]
1-117-041 Control Time 1:Energy Saving *ENG [0 to 300 / 0 / 1sec/step]
1-117-042 Control Time 2:Energy Saving *ENG [0 to 300 / 40 / 1sec/step]
1-117-043 Temp.:Center:1:Energy Saving *ENG [-30 to 30 / 0 / 1deg/step]
1-117-044 Temp.:End:1:Energy Saving *ENG [-30 to 30 / * / 1deg/step]
*NA: 1, EU: 3, Asia: 1, CHN: 1, TWN:
3, KOR: 1
1-117-045 Temp.:Center:2:Energy Saving *ENG [-30 to 30 / 9 / 1deg/step]
1-117-046 Temp.:End:2:Energy Saving
1-117-051 Control Time 1:A4
1-117-052 Control Time 2:A4
1-117-053 Temp.:Center:1:A4
1-117-054 Temp.:End:1:A4
1-117-055 Temp.:Center:2:A4
1-117-056 Temp.:End:2:A4
1-117-061 Control Time 1:A3:M-thick
1-117-062 Control Time 2:A3:M-thick
1-117-063 Temp.:Center:1:A3:M-thick
*ENG [-30 to 30 / 11 / 1deg/step]
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [0 to 300 / 120 / 1sec/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 21 / 1deg/step]
*ENG [-30 to 30 / * / 1deg/step]
*NA: 6, EU: 0, Asia: 0, CHN: 0, TWN:
6, KOR: 0
*ENG [-30 to 30 / -30 / 1deg/step]
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [-30 to 30 / 0 / 1deg/step]
Engine SP Tables - SP1000-1
1-117-064 Temp.:End:1:A3:M-thick
1-117-065 Temp.:Center:2:A3:M-thick
1-117-066 Temp.:End:2:A3:M-thick
1-117-071 Control Time 1:DLT:M-thick
1-117-072 Control Time 2:DLT:M-thick
1-117-073 Temp.:Center:1:DLT:M-thick
1-117-074 Temp.:End:1:DLT:M-thick
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
1-117-075 Temp.:Center:2:DLT:M-thick
1-117-076 Temp.:End:2:DLT:M-thick
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
1-117-081 Control Time 1:Envelope:Long *ENG [0 to 300 / 0 / 1sec/step]
1-117-082 Control Time 2:Envelope:Long *ENG [0 to 300 / 0 / 1sec/step]
1-117-083 Temp.:Center:1:Envelope:Long *ENG [-30 to 30 / 0 / 1deg/step]
1-117-084 Temp.:End:1:Envelope:Long *ENG [-30 to 30 / 10 / 1deg/step]
1-117-085 Temp.:Center:2:Envelope:Long *ENG [-30 to 30 / 0 / 1deg/step]
1-117-086 Temp.:End:2:Envelope:Long *ENG [-30 to 30 / 10 / 1deg/step]
1-117-091 Control Time 1:Envelope:Short *ENG [0 to 300 / 0 / 1sec/step]
1-117-092 Control Time 2:Envelope:Short *ENG [0 to 300 / 0 / 1sec/step]
1-117-093 Temp.:Center:1:Envelope:Short *ENG [-30 to 30 / 0 / 1deg/step]
1-117-094 Temp.:End:1:Envelope:Short *ENG [-30 to 30 / 0 / 1deg/step]
1-117-095 Temp.:Center:2:Envelope:Short *ENG [-30 to 30 / 0 / 1deg/step]
1-117-096 Temp.:End:2:Envelope:Short
1-117-101 Control Time 1:B5
1-117-102 Control Time 2:B5
1-117-103 Temp.:Center:1:B5
1-117-104 Temp.:End:1:B5
1-117-105 Temp.:Center:2:B5
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-125 to 30 / -125 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
93
94
3. Engine SP Mode Tables
1-117-106 Temp.:End:2:B5
1-117-111 Control Time 1:12inch
1-117-112 Control Time 2:12inch
1-117-113 Temp.:Center:1:12inch
1-117-114 Temp.:End:1:12inch
1-117-115 Temp.:Center:2:12inch
1-117-116 Temp.:End:2:12inch
*ENG [-125 to 30 / -125 / 1deg/step]
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [-30 to 30 / -2 / 1deg/step]
*ENG [-30 to 30 / -1 / 1deg/step]
*ENG [-30 to 30 / -2 / 1deg/step]
*ENG [-30 to 30 / -1 / 1deg/step]
1-117-121 Control Time 1:12inch:M-thick *ENG [0 to 300 / 0 / 1sec/step]
1-117-122 Control Time 2:12inch:M-thick *ENG [0 to 300 / 0 / 1sec/step]
1-117-123 Temp.:Center:1:12inch:M-thick *ENG [-30 to 30 / 0 / 1deg/step]
1-117-124 Temp.:End:1:12inch:M-thick *ENG [-30 to 30 / 4 / 1deg/step]
1-117-125 Temp.:Center:2:12inch:M-thick *ENG [-30 to 30 / 0 / 1deg/step]
1-117-126 Temp.:End:2:12inch:M-thick *ENG [-30 to 30 / 4 / 1deg/step]
1-117-131 Control Time 1:SRA3
1-117-132 Control Time 2:SRA3
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [0 to 300 / 11 / 1sec/step]
1-117-133 Temp.:Center:1:SRA3
1-117-134 Temp.:End:1:SRA3
1-117-135 Temp.:Center:2:SRA3
1-117-136 Temp.:End:2:SRA3
1-117-141 Control Time 1:SRA3:M-thick
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 30 / 1 / deg
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 17 / 1deg/step]
*ENG [0 to 300 / 0 / 1sec/step]
1-117-142 Control Time 2:SRA3:M-thick *ENG [0 to 300 / 11 / 1sec/step]
1-117-143 Temp.:Center:1:SRA3:M-thick *ENG [-30 to 30 / 0 / 1deg/step]
1-117-144 Temp.:End:1:SRA3:M-thick *ENG [-30 to 30 / 6 / 1deg/step]
1-117-145 Temp.:Center:2:SRA3:M-thick *ENG [-30 to 30 / 5 / 1deg/step]
1-117-146 Temp.:End:2:SRA3:M-thick
1-117-151 Control Time 1:A3:Low
*ENG [-30 to 30 / 8 / 1deg/step]
*ENG [0 to 300 / 0 / 1sec/step]
Engine SP Tables - SP1000-1
1-117-152 Control Time 2:A3:Low
1-117-153 Temp.:Center:1:A3:Low
1-117-154 Temp.:End:1:A3:Low
1-117-155 Temp.:Center:2:A3:Low
1-117-156 Temp.:End:2:A3:Low
1-117-161 Control Time 1:DLT:Low
1-117-162 Control Time 2:DLT:Low
1-117-163 Temp.:Center:1:DLT:Low
1-117-164 Temp.:End:1:DLT:Low
1-117-165 Temp.:Center:2:DLT:Low
1-117-166 Temp.:End:2:DLT:Low
1-117-171 Control Time 1:A4LEF
1-117-172 Control Time 2:A4LEF
1-117-173 Temp.:Center:1:A4LEF
1-117-174 Temp.:End:1:A4LEF
1-117-175 Temp.:Center:2:A4LEF
1-117-176 Temp.:End:2:A4LEF
1118 [Before Job Temp. Correct]
1-118-001 Temp.:Center:12inch
1-118-002 Temp.:End:12inch
1-118-003 Temp.:Center:A3
1-118-004 Temp.:End:A3
1-118-005 Temp.:Center:DLT
1-118-006 Temp.:End:DLT
1-118-007 Temp.:Center:SRA3
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
95
96
3. Engine SP Mode Tables
1-118-008 Temp.:End:SRA3
1-118-011 Temp.:Center:12inch:M-thick
1-118-012 Temp.:End:12inch:M-thick
1-118-013 Temp.:Center:A3:M-thick
1-118-014 Temp.:End:A3:M-thick
1-118-015 Temp.:Center:DLT:M-thick
1-118-016 Temp.:End:DLT:M-thick
1-118-017 Temp.:Center:SRA3:M-thick
1-118-018 Temp.:End:SRA3:M-thick
1-118-021 Temp.:Center:12inch:Thick
1-118-022 Temp.:End:12inch:Thick
1-118-023 Temp.:Center:A3:Thick
1-118-024 Temp.:End:A3:Thick
1-118-025 Temp.:Center:DLT:Thick
1-118-026 Temp.:End:DLT:Thick
1-118-027 Temp.:Center:SRA3:Thick
1-118-028 Temp.:End:SRA3:Thick
*ENG [-30 to 30 / 17 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 3 / 1deg/step]
*ENG [-30 to 30 / 6 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 0 / 1deg/step]
*ENG [-30 to 30 / 20 / 1deg/step]
1120 [Reserve SP]
1-120-001 Recovery mode SW:Low Temp *ENG [0 to 1 / 0 / 1deg/step]
1-120-002 Recovery mode
SW:Voltage:Low
*ENG [0 to 1 / 0 / 1 deg/step]
1-120-003 UC3 *ENG [0 to 255 / 0 / 1deg/step]
1-120-004 UC4
1-120-005 Ini. CPM Down Time:High
Power
*ENG [0 to 255 / 0 / 1deg/step]
*ENG [0 to 255 / 2 / 1sec/step]
Engine SP Tables - SP1000-1
1-120-006 Ini. CPM Down
Time:Mid.Power
1-120-007 Ini. CPM Down
Time:Voltage:Low
*ENG [0 to 255 / 2 / 1sec/step]
*ENG [0 to 255 / 2 / 1sec/step]
1-120-008 Ini. CPM Down Time:Low Temp *ENG [0 to 255 / 2 / 1sec/step]
1-120-009 Temp.:Center:
3:DLT:Voltage:Low
*ENG [0 to 30 / 0 / 1deg/step]
1-120-010 Temp.:End:3:DLT:Voltage:Low *ENG [0 to 30 / 0 / 1deg/step]
1-120-011 Control Time
1:DLT:Voltage:Low
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [0 to 300 / 0 / 1sec/step] 1-120-012 Control Time
2:DLT:Voltage:Low
1-120-013 Control Time
3:DLT:Voltage:Low
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [0 to 300 / 0 / 1sec/step] 1-120-014 Control Time
1:DLT:Voltage:Low
1-120-015 Control Time
2:DLT:Voltage:Low
1-120-016 Control Time
3:DLT:Voltage:Low
1-120-017 UW7
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [0 to 300 / 0 / 1sec/step]
*ENG [0 to 60000 / 0 / 1msec/step]
1-120-018 UW8 *ENG [0 to 60000 / 0 / 1msec/step]
1-120-019 Temp.:End:2:DLT:Voltage:Low *ENG [0 to 100.00 / 0 / 0.01sec/step]
*ENG [0 to 100.00 / 0 / 0.01sec/step] 1-120-020 Temp.:Center:
3:DLT:Voltage:Low
1-120-021 Temp.:Center:
1:DLT:Voltage:Low
*ENG [-30 to 30 / 0 / 1deg/step]
1-120-022 Temp.:End:1:DLT:Voltage:Low *ENG [-30 to 30 / 0 / 1deg/step]
1-120-023 Temp.:Center:
2:DLT:Voltage:Low
*ENG [-30 to 30 / 0 / 1deg/step]
97
98
3. Engine SP Mode Tables
1-120-024 Temp.:End:2:DLT:Voltage:Low *ENG [-30 to 30 / 0 / 1deg/step]
1-120-025 Temp.:Center:
3:DLT:Voltage:Low
*ENG [-30 to 30 / 0 / 1deg/step]
1-120-026 Temp.:End:3:DLT:Voltage:Low *ENG [-30 to 30 / 0 / 1deg/step]
1-120-027 Temp.:Center:
1:DLT:Voltage:Low
*ENG [-30 to 30 / 0 / 1deg/step]
1-120-028 Temp.:End:1:DLT:Voltage:Low *ENG [-30 to 30 / 0 / 1deg/step]
1-120-029 Temp.:Center:
2:DLT:Voltage:Low
*ENG [-30 to 30 / 0 / 1deg/step]
1-120-030 Temp.:End:2:DLT:Voltage:Low *ENG [-30 to 30 / 0 / 1deg/step]
1121 [Switch:Rotation Start/Stop]
1-121-001 Time:After Reload
1-121-002 Time:After Recovery
1-121-004 Press Temp.:After Reload
1-121-005 End Temp.:After Job:SRA3
1-121-006 ShiftTemp:After
Job:PressEdge:A3
1-121-007 ShiftTemp:After
Job:PressEdge:DLT
1-121-008 Overshoot Prevent Temp.
1-121-009 Overshoot Prevent Time
1-121-010 End Temp.:After Job:B4
1-121-011 End Temp.:After Job:LT
1-121-012 End Temp.:After Job:B5
1-121-013 End Temp.:After Job:A5
1-121-014 End Temp.:After Job:B6
*ENG [0 to 100 / 30 / 1sec/step]
*ENG [0 to 100 / 15 / 1sec/step]
*ENG [0 to 160 / 160 / 1deg/step]
*ENG [100 to 250 / 200 / 1deg/step]
*ENG [100 to 250 / 200 / 1deg/step]
*ENG [100 to 250 / 200 / 1deg/step]
*ENG [0 to 250 / 185 / 1deg/step]
*ENG [0 to 100 / 10 / 1sec/step]
*ENG [100 to 250 / 143 / 1deg/step]
*ENG [100 to 250 / * / 1deg/step]
*NA: 210, EU: 153, Asia: 153, CHN:
153, TWN: 210, KOR: 153
*ENG [100 to 250 / 155 / 1deg/step]
*ENG [100 to 250 / 155 / 1deg/step]
*ENG [100 to 250 / 145 / 1deg/step]
Engine SP Tables - SP1000-1
1-121-015 ShiftTemp:FC:After
Job:PressCenter:A6
1-121-016 ShiftTemp:Bk:After Job:PressFl-
B_Edge:SRA3
1-121-017 ShiftTemp:Bk:After
Job:PressEdge:A3
1-121-018 ShiftTemp:Bk:After
Job:PressEdge:DLT
1-121-019 ShiftTemp:Bk:After
Job:PressEdge:B4
1-121-020 ShiftTemp:Bk:After
Job:FusingEdge:LT
*ENG [100 to 250 / 160 / 1deg/step]
*ENG [100 to 250 / 200 / 1deg/step]
*ENG [100 to 250 / 200 / 1deg/step]
*ENG [100 to 250 / 200 / 1deg/step]
*ENG [100 to 250 / 148 / 1deg/step]
1-121-021 Time:After Main Switch On
1-121-022 ShiftTemp:Bk:After
Job:PressCenter:B5
1-121-023 ShiftTemp:Bk:After
Job:PressCenter:A5
1-121-024 ShiftTemp:Bk:After
Job:PressCenter:B6
*ENG [100 to 250 / * / 1deg/step]
*NA: 215, EU: 153, Asia: 153, CHN:
153, TWN: 215, KOR: 153
*ENG [0 to 100 / 30 / 1sec/step]
*ENG [100 to 250 / 160 / 1deg/step]
*ENG [100 to 250 / 160 / 1deg/step]
*ENG [100 to 250 / 150 / 1deg/step]
1-121-025 ShiftTemp:Bk:After
Job:PressCenter:A6
*ENG [100 to 250 / 150 / 1deg/step]
1-121-031 Pre Job Paper Feed Time:FC:A3 *ENG [0 to 10000 / 10000 / 1sec/step]
1-121-032 Soaking Rotary Time:FC:A3
1-121-033 Pre Job Paper Feed
Time:FC:DLT
1-121-034 Soaking Rotary Time:FC:DLT
*ENG [0 to 100 / 0 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 100 / 0 / 1sec/step]
1-121-035 Pre Job Paper Feed Time:FC:B4 *ENG [0 to 10000 / 235 / 1sec/step]
1-121-036 Soaking Rotary Time:FC:B4 *ENG [0 to 100 / 15 / 1sec/step]
1-121-037 Pre Job Paper Feed Time:FC:LT *ENG [0 to 10000 / 250 / 1sec/step]
99
100
3. Engine SP Mode Tables
1-121-038 Soaking Rotary Time:FC:LT *ENG [0 to 100 / 10 / 1sec/step]
1-121-039 Pre Job Paper Feed Time:FC:B5 *ENG [0 to 10000 / 180 / 1sec/step]
1-121-040 Soaking Rotary Time:FC:B5 *ENG [0 to 100 / 15 / 1sec/step]
1-121-041 Pre Job Paper Feed Time:FC:A5 *ENG [0 to 10000 / 31 / 1sec/step]
1-121-042 Soaking Rotary Time:FC:A5 *ENG [0 to 100 / 20 / 1sec/step]
1-121-043 Pre Job Paper Feed Time:FC:B6 *ENG [0 to 10000 / 27 / 1sec/step]
1-121-044 Soaking Rotary Time:FC:B6 *ENG [0 to 100 / 25 / 1sec/step]
1-121-045 Pre Job Paper Feed Time:FC:A6 *ENG [0 to 10000 / * / 1sec/step]
*NA: 70, EU: 40, Asia: 40, CHN: 40,
TWN: 70 , KOR: 40
1-121-046 Soaking Rotary Time:FC:A6 *ENG [0 to 100 / 60 / 1sec/step]
1-121-051 Pre Job Paper Feed Time:Bk:A3 *ENG [0 to 10000 / 10000 / 1sec/step]
1-121-052 Soaking Rotary Time:Bk:A3 *ENG [0 to 100 / 0 / 1sec/step]
1-121-053 Pre Job Paper Feed
Time:Bk:DLT
*ENG [0 to 10000 / 10000 / 1sec/step]
1-121-054 Soaking Rotary Time:Bk:DLT *ENG [0 to 100 / 0 / 1sec/step]
1-121-055 Pre Job Paper Feed Time:Bk:B4 *ENG [0 to 10000 / 235 / 1sec/step]
1-121-056 Soaking Rotary Time:Bk:B4 *ENG [0 to 100 / 10 / 1sec/step]
1-121-057 Pre Job Paper Feed Time:Bk:LT *ENG [0 to 10000 / 250 / 1sec/step]
1-121-058 Soaking Rotary Time:Bk:LT *ENG [0 to 100 / 5 / 1sec/step]
1-121-059 Pre Job Paper Feed Time:Bk:B5 *ENG [0 to 10000 / 180 / 1sec/step]
1-121-060 Soaking Rotary Time:Bk:B5 *ENG [0 to 100 / 10 / 1sec/step]
1-121-061 Pre Job Paper Feed Time:Bk:A5 *ENG [0 to 10000 / 31 / 1sec/step]
1-121-062 Soaking Rotary Time:Bk:A5 *ENG [0 to 100 / 20 / 1sec/step]
1-121-063 Pre Job Paper Feed Time:Bk:B6 *ENG [0 to 10000 / 27 / 1sec/step]
1-121-064 Soaking Rotary Time:Bk:B6 *ENG [0 to 100 / 20 / 1sec/step]
1-121-065 Pre Job Paper Feed Time:Bk:A6 *ENG [0 to 10000 / 80 / 1sec/step]
Engine SP Tables - SP1000-1
1-121-066 Soaking Rotary Time:Bk:A6
1-121-080 Shift Time: AfterReload:
LineSpd Dwn
*ENG [0 to 100 / 5 / 1sec/step]
*ENG [0 to 60 / 10 / 0.1sec/step]
1-121-101 Heat Off Time:Start:Warm Up *ENG [0 to 60000 / 0 / 1msec/step]
1-121-102 Heat Off Time:Start:End of A
Control
*ENG [0 to 600000 / 100000 / 1msec/ step]
1-121-103 Time After Feeler Edge Detect *ENG [0 to 200 / 0 / 1sec/step]
1-121-114 Relay ON Temp.:Warm Up
1-121-120 ShiftTemp:Press_Full-Bd
Edge:SRA3
1-121-121 ShiftTemp:PressEdge:A3
*ENG [0 to 250 / 200 / 1deg/step]
*ENG [100 to 250 / 220 / 1deg/step]
1-121-122 ShiftTemp:PressEdge:DLT
1-121-123 ShiftTemp:PressEdge:B4
*ENG [100 to 250 / 215 / 1deg/step]
*ENG [100 to 250 / 205 / 1deg/step]
*ENG [100 to 250 / 215 / 1deg/step]
1-121-124 ShiftTemp:FusingEdge:LT
1-121-125 ShiftTemp:PressCenter:B5
1-121-126 ShiftTemp:PressCenter:A5
1-121-127 ShiftTemp:PressCenter:B6
1-121-128 ShiftTemp:PressCenter:A6
1-121-141 Pre Job Paper Feed Time:A3
1-121-142 Soaking Rotary Time:A3
1-121-143 Pre Job Paper Feed Time:DLT
1-121-144 Soaking Rotary Time:DLT
1-121-145 Pre Job Paper Feed Time:B4
1-121-146 Soaking Rotary Time:B4
1-121-147 Pre Job Paper Feed Time:LT
1-121-148 Soaking Rotary Time:LT
1-121-149 Pre Job Paper Feed Time:B5
*ENG [100 to 250 / 225 / 1deg/step]
*ENG [100 to 250 / 220 / 1deg/step]
*ENG [100 to 250 / 210 / 1deg/step]
*ENG [100 to 250 / 210 / 1deg/step]
*ENG [100 to 250 / 210 / 1deg/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 100 / 10 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 100 / 10 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 100 / 10 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 100 / 10 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
101
102
3. Engine SP Mode Tables
1-121-150 Soaking Rotary Time:B5
1-121-151 Pre Job Paper Feed Time:A5
1-121-152 Soaking Rotary Time:A5
1-121-153 Pre Job Paper Feed Time:B6
1-121-154 Soaking Rotary Time:B6
1-121-155 Pre Job Paper Feed Time:A6
1-121-156 Soaking Rotary Time:A6
1122 [Standby Rotation Setting]
1-122-001 Rotation Interval
1-122-002 Rotation Time
1123 [Paper Jam Rotation Setting]
1-123-001 Normal Rotation Distance
1-123-002 Reverse Rotation Distance
1124 [CPM Down Setting] DFU
1-124-001 High:Down Temp.
1-124-002 High:Up Temp.
1-124-003 Low :1st CPM
1-124-004 Low :2nd CPM
1-124-005 Low :3rd CPM
1-124-007 High:2nd CPM
1-124-008 High:3rd CPM
1-124-009 High:1st CPM Down
Temp.:A3:Press End
1-124-010 High:2nd CPM Down
Temp.:A3:Press End
*ENG [0 to 100 / 10 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 100 / 10 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 100 / 10 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 100 / 10 / 1sec/step]
*ENG [0 to 240 / 60 / 1min/step]
*ENG [0.0 to 60.0 / 8.0 / 0.1sec/step]
*ENG [0 to 10000 / 75 / 1mm/step]
*ENG [0 to 10000 / 25 / 1mm/step]
*ENG [-50 to 0 / -30 / 1deg/step]
*ENG [-50 to 0 / -15 / 1deg/step]
*ENG [10 to 100 / 80 / 1%/step]
*ENG [10 to 100 / 65 / 1%/step]
*ENG [10 to 100 / 50 / 1%/step]
*ENG [10 to 100 / 50 / 1%/step]
*ENG [10 to 100 / 30 / 1%/step]
*ENG [100 to 250 / 205 / 1deg/step]
*ENG [100 to 250 / 210 / 1deg/step]
1-124-011 High:3rd CPM Down
Temp.:A3:Press End
1-124-012 High:1st CPM Down
Temp.:DLT:Press End
1-124-013 High:2nd CPM Down
Temp.:DLT:Press End
1-124-014 High:3rd CPM Down
Temp.:DLT:Press End
1-124-015 High:1st CPM Down
Temp.:B4:Press End
1-124-016 High:2nd CPM Down
Temp.:B4:Press End
1-124-017 High:3rd CPM Down
Temp.:B4:Press End
1-124-018 High:1st CPM Down
Temp.:LT:Fuser End
1-124-019 High:2nd CPM Down
Temp.:LT:Fuser End
1-124-020 High:3rd CPM Down
Temp.:LT:Fuser End
1-124-021 High:1st CPM Down
Temp.:A4:Fuser End
1-124-022 High:2nd CPM Down
Temp.:A4:Fuser End
1-124-023 High:3rd CPM Down
Temp.:A4:Fuser End
1-124-024 High:1st CPM Down
Temp.:B5:Press Center
1-124-025 High:2nd CPM Down
Temp.:B5:Press Center
1-124-026 High:3rd CPM Down
Temp.:B5:Press Center
Engine SP Tables - SP1000-1
*ENG [100 to 250 / 215 / 1deg/step]
*ENG [100 to 250 / 205 / 1deg/step]
*ENG [100 to 250 / 210 / 1deg/step]
*ENG [100 to 250 / 215 / 1deg/step]
*ENG [100 to 250 / 200 / 1deg/step]
*ENG [100 to 250 / 210 / 1deg/step]
*ENG [100 to 250 / 215 / 1deg/step]
*ENG [100 to 250 / 215 / 1deg/step]
*ENG [100 to 250 / 220 / 1deg/step]
*ENG [100 to 250 / 225 / 1deg/step]
*ENG [100 to 250 / 215 / 1deg/step]
*ENG [100 to 250 / 220 / 1deg/step]
*ENG [100 to 250 / 225 / 1deg/step]
*ENG [100 to 250 / 205 / 1deg/step]
*ENG [100 to 250 / 210 / 1deg/step]
*ENG [100 to 250 / 215 / 1deg/step]
103
104
3. Engine SP Mode Tables
1-124-027 High:1st CPM Down
Temp.:A5:Press Center
1-124-028 High:2nd CPM Down
Temp.:A5:Press Center
1-124-029 High:3rd CPM Down
Temp.:A5:Press Center
1-124-030 High:1st CPM Down
Temp.:B6:Press Center
1-124-031 High:2nd CPM Down
Temp.:B6:Press Center
1-124-032 High:3rd CPM Down
Temp.:B6:Press Center
1-124-033 High:1st CPM Down
Temp.:A6:Press Center
1-124-034 High:2nd CPM Down
Temp.:A6:Press Center
1-124-035 High:3rd CPM Down
Temp.:A6:Press Center
1-124-036 High:1st CPM Down
Temp.:SRA3:Press End
1-124-037 High:2nd CPM Down
Temp.:SRA3:Press End
1-124-038 High:3rd CPM Down
Temp.:SRA3:Press End
1-124-040 Low Temp.:1st CPM_2
*ENG [100 to 250 / * / 1deg/step]
*NA: 170, EU: 204, Asia: 204, CHN:
204, TWN: 170, KOR: 204
*ENG [100 to 250 / 209 / 1deg/step]
*ENG [100 to 250 / 217 / 1deg/step]
*ENG [100 to 250 / * / 1deg/step]
*NA: 180, EU: 209, Asia: 209, CHN:
209, TWN: 180, KOR: 209
*ENG [100 to 250 / * / 1deg/step]
*NA: 185, EU: 214, Asia: 214, CHN:
214, TWN: 185, KOR: 214
*ENG [100 to 250 / * / 1deg/step]
*NA: 192, EU: 219, Asia: 219, CHN:
29, TWN: 192, KOR: 219
*ENG [100 to 250 / * / 1deg/step]
*NA: 180, EU: 209, Asia: 209, CHN:
209, TWN: 180, KOR: 209
*ENG [100 to 250 / * / 1deg/step]
*NA: 185, EU: 214, Asia: 214, CHN:
214, TWN: 185, KOR: 214
*ENG [100 to 250 / * / 1deg/step]
*NA: 192, EU: 219, Asia: 219, CHN:
29, TWN: 192, KOR: 219
*ENG [100 to 250 / 210 / 1deg/step]
*ENG [100 to 250 / 215 / 1deg/step]
*ENG [100 to 250 / 220 / 1deg/step]
*ENG [10 to 100 / 80 / 1%/step]
Engine SP Tables - SP1000-1
1-124-041 Low Temp.:2nd CPM_2
1-124-042 Low Temp.:1st CPM_3
1-124-043 Low Temp.:2nd CPM_3
1-124-051 Judging Interval
1-124-060 Ini. CPM Down Time
*ENG [10 to 100 / 65 / 1%/step]
*ENG [10 to 100 / 80 / 1%/step]
*ENG [10 to 100 / 65 / 1%/step]
*ENG [1 to 250 / 4 / 1sec/step]
*ENG [0 to 255 / 2 / 1sec/step]
1-124-061 Ini. CPM Down Time 10sec recovery
*ENG [0 to 255 / 2 / 1sec/step]
1-124-071 L:High:1st Temp.:DLT:Press End *ENG [100 to 250 / 205 / 1deg/step]
1-124-072 L:High:2nd Temp.:DLT:Press
End
*ENG [100 to 250 / 210 / 1deg/step]
1-124-073 L:High:3rd Temp.:DLT:Press End *ENG [100 to 250 / 215 / 1deg/step]
1-124-074 L:High:4th Temp.:DLT:Press End *ENG [100 to 250 / 215 / 1deg/step]
1-124-075 L:High:1st Temp.:B4:Press End *ENG [100 to 250 / 180 / 1deg/step]
1-124-076 L:High:2nd Temp.:B4:Press End *ENG [100 to 250 / 180 / 1deg/step]
1-124-077 L:High:3rd Temp.:B4:Press End *ENG [100 to 250 / 215 / 1deg/step]
1-124-078 L:High:4th Temp.:B4:Press End *ENG [100 to 250 / 215 / 1deg/step]
1-124-079 L:High:1st Temp.:B5:Press
Center
*ENG [100 to 250 / * / 1deg/step]
*NA: 155, EU: 193, Asia: 193, CHN:
193, TWN: 205, KOR: 193
1-124-080 L:High:2nd Temp.:B5:Press
Center
*ENG [100 to 250 / * / 1deg/step]
*NA: 160, EU: 199, Asia: 199, CHN:
199, TWN: 210, KOR: 199
1-124-081 L:High:3rd Temp.:B5:Press
Center
1-124-082 L:High:4th Temp.:B5:Press
Center
*ENG [100 to 250 / * / 1deg/step]
*NA: 165, EU: 205, Asia: 205, CHN:
205, TWN: 165, KOR: 205
*ENG [100 to 250 / * / 1deg/step]
*NA: 200, EU: 205, Asia: 205, CHN:
205, TWN: 200, KOR: 205
105
106
3. Engine SP Mode Tables
1-124-083 L:High:1st Temp.:A5:Press
Center
1-124-084 L:High:2nd Temp.:A5:Press
Center
1-124-085 L:High:3rd Temp.:A5:Press
Center
1-124-086 L:High:4th Temp.:A5:Press
Center
1-124-087 L:High:1st Temp.:B6:Press
Center
1-124-088 L:High:2nd Temp.:B6:Press
Center
1-124-089 L:High:3rd Temp.:B6:Press
Center
1-124-090 L:High:4th Temp.:B6:Press
Center
1-124-091 L:High:1st Temp.:A6:Press
Center
1-124-092 L:High:2nd Temp.:A6:Press
Center
*ENG [100 to 250 / * / 1deg/step]
*NA: 160, EU: 193, Asia: 193, CHN:
193, TWN: 160, KOR: 193
*ENG [100 to 250 / * / 1deg/step]
*NA: 170, EU: 199, Asia: 199, CHN:
199, TWN: 170, KOR: 199
*ENG [100 to 250 / * / 1deg/step]
*NA: 190, EU: 205, Asia: 205, CHN:
205, TWN: 190, KOR: 205
*ENG [100 to 250 / * / 1deg/step]
*NA: 200, EU: 205, Asia: 205, CHN:
205, TWN: 200, KOR: 205
*ENG [100 to 250 / * / 1deg/step]
*NA: 155, EU: 191, Asia: 191, CHN:
191, TWN: 155, KOR: 191
*ENG [100 to 250 / * / 1deg/step]
*NA: 178, EU: 196, Asia: 196, CHN:
196, TWN: 178, KOR: 196
*ENG [100 to 250 / * / 1deg/step]
*NA: 192, EU: 201, Asia: 201, CHN:
201, TWN: 192, KOR: 201
*ENG [100 to 250 / * / 1deg/step]
*NA: 192, EU: 201, Asia: 201, CHN:
201, TWN: 192, KOR: 201
*ENG [100 to 250 / * / 1deg/step]
*NA: 155, EU: 191, Asia: 191, CHN:
191, TWN: 155, KOR: 191
*ENG [100 to 250 / * / 1deg/step]
*NA: 178, EU: 196, Asia: 196, CHN:
196, TWN: 178, KOR: 196
Engine SP Tables - SP1000-1
1-124-093 L:High:3rd Temp.:A6:Press
Center
*ENG [100 to 250 / * / 1deg/step]
*NA: 192, EU: 201, Asia: 201, CHN:
201, TWN: 192, KOR: 201
1-124-094 L:High:4th Temp.:A6:Press
Center
*ENG [100 to 250 / * / 1deg/step]
*NA: 192, EU: 201, Asia: 201, CHN:
201, TWN: 192, KOR: 201
1-124-101 High:1st CPM Down Time:A3 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-102 High:2nd CPM Down Time:A3 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-103 High:3rd CPM Down Time:A3 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-104 High:1st CPM Down Time:DLT *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-105 High:2nd CPM Down Time:DLT *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-106 High:3rd CPM Down Time:DLT *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-107 High:1st CPM Down Time:B4 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-108 High:2nd CPM Down Time:B4 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-109 High:3rd CPM Down Time:B4 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-110 High:1st CPM Down Time:LT *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-111 High:2nd CPM Down Time:LT *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-112 High:3rd CPM Down Time:LT *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-113 High:1st CPM Down Time:A4 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-114 High:2nd CPM Down Time:A4 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-115 High:3rd CPM Down Time:A4 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-116 High:1st CPM Down Time:B5 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-117 High:2nd CPM Down Time:B5 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-118 High:3rd CPM Down Time:B5 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-119 High:1st CPM Down Time:A5 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-120 High:2nd CPM Down Time:A5 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-121 High:3rd CPM Down Time:A5 *ENG [0 to 10000 / 10000 / 1sec/step]
107
108
3. Engine SP Mode Tables
1-124-122 High:1st CPM Down Time:B6 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-123 High:2nd CPM Down Time:B6 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-124 High:3rd CPM Down Time:B6 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-125 High:1st CPM Down Time:A6 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-126 High:2nd CPM Down Time:A6 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-127 High:3rd CPM Down Time:A6 *ENG [0 to 10000 / 10000 / 1sec/step]
1-124-128 High:1st CPM Down
Time:SRA3
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step] 1-124-129 High:2nd CPM Down
Time:SRA3
1-124-130 High:3rd CPM Down
Time:SRA3
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step] 1-124-151 High:1st CPM Down
Time:A3:Low Speed
1-124-152 High:2nd CPM Down
Time:A3:Low Speed
1-124-153 High:3rd CPM Down
Time:A3:Low Speed
1-124-154 High:1st CPM Down
Time:DLT:Low Speed
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
1-124-155 High:2nd CPM Down
Time:DLT:Low Speed
1-124-156 High:3rd CPM Down
Time:DLT:Low Speed
1-124-157 High:1st CPM Down
Time:B4:Low Speed
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step] 1-124-158 High:2nd CPM Down
Time:B4:Low Speed
1-124-159 High:3rd CPM Down
Time:B4:Low Speed
*ENG [0 to 10000 / 10000 / 1sec/step]
1-124-160 High:1st CPM Down
Time:LT:Low Speed
1-124-161 High:2nd CPM Down
Time:LT:Low Speed
1-124-162 High:3rd CPM Down
Time:LT:Low Speed
1-124-163 High:1st CPM Down
Time:A4:Low Speed
1-124-164 High:2nd CPM Down
Time:A4:Low Speed
1-124-165 High:3rd CPM Down
Time:A4:Low Speed
1-124-166 High:1st CPM Down
Time:B5:Low Speed
1-124-167 High:2nd CPM Down
Time:B5:Low Speed
1-124-168 High:3rd CPM Down
Time:B5:Low Speed
1-124-169 High:1st CPM Down
Time:A5:Low Speed
1-124-170 High:2nd CPM Down
Time:A5:Low Speed
1-124-171 High:3rd CPM Down
Time:A5:Low Speed
1-124-172 High:1st CPM Down
Time:B6:Low Speed
1-124-173 High:2nd CPM Down
Time:B6:Low Speed
1-124-174 High:3rd CPM Down
Time:B6:Low Speed
1-124-175 High:1st CPM Down
Time:A6:Low Speed
Engine SP Tables - SP1000-1
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 60 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 60 / 1sec/step]
109
110
3. Engine SP Mode Tables
1-124-176 High:2nd CPM Down
Time:A6:Low Speed
1-124-177 High:3rd CPM Down
Time:A6:Low Speed
1-124-178 High:1st CPM Down
Time:SRA3:Low Speed
1-124-179 High:2nd CPM Down
Time:SRA3:Low Speed
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
*ENG [0 to 10000 / 10000 / 1sec/step]
1-124-180 High:3rd CPM Down
Time:SRA3:Low Speed
*ENG [0 to 10000 / 10000 / 1sec/step]
1-124-190 NC:1st CPM:Decreased Temp.
*ENG [80 to 250 / 123 / 1deg/step]
1-124-191 NC:2nd CPM:Decreased
Temp.
*ENG [80 to 250 / 124 / 1deg/step]
1-124-192 NC:3rd CPM:Decreased Temp. *ENG [80 to 250 / 125 / 1deg/step]
1-124-193 NC:1st CPM:Decreased Ratio *ENG [10 to 100 / 50 / 1%/step]
1-124-194 NC:2nd CPM:Decreased Ratio *ENG [10 to 100 / 30 / 1%/step]
1-124-195 NC:3rd CPM:Decreased Ratio *ENG [10 to 100 / 10 / 1%/step]
1-124-201 Low:Down Temp.
1-124-202 Low:Up Temp.
*ENG [-50 to 0 / -30 / 1deg/step]
*ENG [-50 to 0 / -15 / 1deg/step]
*ENG [-50 to 0 / -20 / 1deg/step] 1-124-203 High Temp: Decreased Temp:
Mid-Low Spd
1-124-204 High Temp: Increased Temp:
Mid-Low Spd
*ENG [-50 to 0 / -15 / 1deg/step]
1-124-205 Low Temp: Decreased Temp:
Mid-Low Spd
*ENG [-50 to 0 / -20 / 1deg/step]
1-124-206 Low Temp: Increased Temp:
Mid-Low Spd
1-124-210 Temp.:Threshold::Low Power
*ENG [-50 to 0 / -15 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
1-124-211 CPM Level 2: Judge:Low Power *ENG [0 to 200 / 110 / 1deg/step]
Engine SP Tables - SP1000-1
1-124-212 Temp.:Threshold:Judge:Mid.
Power
1-124-213 CPM Level 2: Judge:Mid.
Power
1-124-214 Temp.:Threshold:Judge:High
Power
1-124-215 CPM Level 2: Judge:High
Power
1-124-220 Ini.: HighTemp: DownTemp
1-124-221 Ini.: HighTemp: UpTemp
1-124-222 Ini.: LowTemp: DownTemp
1-124-223 Ini.: LowTemp: UpTemp
1-124-224 Ini.: HighTemp: DownTemp:
Mid-Low Spd
1-124-225 Ini.: HighTemp: UpTemp: Mid-
Low Spd
1-124-226 Ini.: LowTemp: DownTemp:
Mid-Low Spd
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 110 / 1deg/step]
*ENG [0 to 200 / 0 / 1deg/step]
*ENG [0 to 200 / 110 / 1deg/step]
*ENG [-50 to 0 / -30 / 1deg/step]
*ENG [-50 to 50 / -15 / 1deg/step]
*ENG [-50 to 0 / -30 / 1deg/step]
*ENG [-50 to 50 / -15 / 1deg/step]
*ENG [-50 to 0 / -20 / 1deg/step]
*ENG [-50 to 50 / -15 / 1deg/step]
*ENG [-50 to 0 / -20 / 1deg/step]
1-124-227 Ini.: LowTemp: UpTemp: Mid-
Low Spd
1-124-241 L:High:3rd Temp.:SRA3:Press
End
*ENG [-50 to 50 / -15 / 1deg/step]
*ENG [100 to 250 / 220 / 1deg/step]
1-124-242 L:High:3rd Temp.:A3:Press End *ENG [100 to 250 / 215 / 1deg/step]
1-124-243 L:High:3rd Temp.:DLT:Press End *ENG [100 to 250 / 215 / 1deg/step]
1-124-244 L:High:3rd Temp.:B4:Press End *ENG [100 to 250 / 215 / 1deg/step]
1-124-245 L:High:3rd Temp.:LT:Fuser End *ENG [100 to 250 / 225 / 1deg/step]
1-124-246 L:High:3rd Temp.:A4:Fuser End *ENG [100 to 250 / 225 / 1deg/step]
1-124-247 L:High:3rd Temp.:B5:Press
Center
*ENG [100 to 250 / 215 / 1deg/step]
111
112
3. Engine SP Mode Tables
1-124-248 L:High:3rd Temp.:A5:Press
Center
1-124-249 L:High:3rd Temp.:B6:Press
Center
1-124-250 L:High:3rd Temp.:A6:Press
Center
*ENG [100 to 250 / 217 / 1deg/step]
*ENG [100 to 250 / * / 1deg/step]
*NA: 192, EU: 219, Asia: 219, CHN:
219, TWN: 192, KOR: 219
*ENG [100 to 250 / * / 1deg/step]
*NA: 192, EU: 219, Asia: 219, CHN:
219, TWN: 192, KOR: 219
1125 [CPM Down Setting]
1-125-001 High:1st CPM:A3:Large
Size:Normal Speed
1-125-002 High:2nd CPM:A3:Large
Size:Normal Speed
1-125-003 High:3rd CPM:A3:Large
Size:Normal Speed
1-125-004 High:1st CPM:A3:Small
Size:Normal Speed
1-125-005 High:2nd CPM:A3:Small
Size:Normal Speed
1-125-006 High:3rd CPM:A3:Small
Size:Normal Speed
1-125-007 High:1st CPM:DLT:Large
Size:Normal Speed
1-125-008 High:2nd CPM:DLT:Large
Size:Normal Speed
1-125-009 High:3rd CPM:DLT:Large
Size:Normal Speed
1-125-010 High:1st CPM:DLT:Small
Size:Normal Speed
1-125-011 High:2nd CPM:DLT:Small
Size:Normal Speed
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 30 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 30 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 30 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
Engine SP Tables - SP1000-1
1-125-012 High:3rd CPM:DLT:Small
Size:Normal Speed
1-125-013 High:1st CPM:B4:Large
Size:Normal Speed
1-125-014 High:2nd CPM:B4:Large
Size:Normal Speed
1-125-015 High:3rd CPM:B4:Large
Size:Normal Speed
1-125-016 High:1st CPM:B4:Small
Size:Normal Speed
1-125-017 High:2nd CPM:B4:Small
Size:Normal Speed
1-125-018 High:3rd CPM:B4:Small
Size:Normal Speed
1-125-019 High:1st CPM:LT:Large
Size:Normal Speed
1-125-020 High:2nd CPM:LT:Large
Size:Normal Speed
1-125-021 High:3rd CPM:LT:Large
Size:Normal Speed
1-125-022 High:1st CPM:LT:Small
Size:Normal Speed
1-125-023 High:2nd CPM:LT:Small
Size:Normal Speed
1-125-024 High:3rd CPM:LT:Small
Size:Normal Speed
1-125-025 High:1st CPM:A4:Large
Size:Normal Speed
1-125-026 High:2nd CPM:A4:Large
Size:Normal Speed
1-125-027 High:3rd CPM:A4:Large
Size:Normal Speed
*ENG [0 to 100 / 30 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 30 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 30 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 30 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 30 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 30 / 1%/step]
113
114
3. Engine SP Mode Tables
1-125-028 High:1st CPM:A4:Small
Size:Normal Speed
1-125-029 High:2nd CPM:A4:Small
Size:Normal Speed
1-125-030 High:3rd CPM:A4:Small
Size:Normal Speed
1-125-031 High:1st CPM:B5:Large
Size:Normal Speed
1-125-032 High:2nd CPM:B5:Large
Size:Normal Speed
1-125-033 High:3rd CPM:B5:Large
Size:Normal Speed
1-125-034 High:1st CPM:B5:Small
Size:Normal Speed
1-125-035 High:2nd CPM:B5:Small
Size:Normal Speed
1-125-036 High:3rd CPM:B5:Small
Size:Normal Speed
1-125-037 High:1st CPM:A5:Normal
Speed
1-125-038 High:2nd CPM:A5:Normal
Speed
1-125-039 High:3rd CPM:A5:Normal
Speed
1-125-040 High:1st CPM:B6:Normal
Speed
1-125-041 High:2nd CPM:B6:Normal
Speed
1-125-042 High:3rd CPM:B6:Normal
Speed
1-125-043 High:1st CPM:A6:Normal
Speed
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 30 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 30 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 30 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 30 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 30 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
Engine SP Tables - SP1000-1
1-125-044 High:2nd CPM:A6:Normal
Speed
1-125-045 High:3rd CPM:A6:Normal
Speed
1-125-046 High:1st CPM:SRA3:Large
Size:Normal Speed
1-125-047 High:2nd CPM:SRA3:Large
Size:Normal Speed
1-125-048 High:3rd CPM:SRA3:Large
Size:Normal Speed
1-125-049 High:1st CPM:SRA3:Small
Size:Normal Speed
1-125-050 High:2nd CPM:SRA3:Small
Size:Normal Speed
1-125-051 High:3rd CPM:SRA3:Small
Size:Normal Speed
1-125-101 High:1st CPM:A3:Large
Size:Middle Speed
1-125-102 High:2nd CPM:A3:Large
Size:Middle Speed
1-125-104 High:1st CPM:A3:Small
Size:Middle Speed
1-125-105 High:2nd CPM:A3:Small
Size:Middle Speed
1-125-107 High:1st CPM:DLT:Large
Size:Middle Speed
1-125-108 High:2nd CPM:DLT:Large
Size:Middle Speed
1-125-110 High:1st CPM:DLT:Small
Size:Middle Speed
1-125-111 High:2nd CPM:DLT:Small
Size:Middle Speed
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 30 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 30 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 30 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
115
116
3. Engine SP Mode Tables
1-125-113 High:1st CPM:B4:Large
Size:Middle Speed
1-125-114 High:2nd CPM:B4:Large
Size:Middle Speed
1-125-116 High:1st CPM:B4:Small
Size:Middle Speed
1-125-117 High:2nd CPM:B4:Small
Size:Middle Speed
1-125-119 High:1st CPM:LT:Large
Size:Middle Speed
1-125-120 High:2nd CPM:LT:Large
Size:Middle Speed
1-125-122 High:1st CPM:LT:Small
Size:Middle Speed
1-125-123 High:2nd CPM:LT:Small
Size:Middle Speed
1-125-125 High:1st CPM:A4:Large
Size:Middle Speed
1-125-126 High:2nd CPM:A4:Large
Size:Middle Speed
1-125-128 High:1st CPM:A4:Small
Size:Middle Speed
1-125-129 High:2nd CPM:A4:Small
Size:Middle Speed
1-125-131 High:1st CPM:B5:Large
Size:Middle Speed
1-125-132 High:2nd CPM:B5:Large
Size:Middle Speed
1-125-134 High:1st CPM:B5:Small
Size:Middle Speed
1-125-135 High:2nd CPM:B5:Small
Size:Middle Speed
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
Engine SP Tables - SP1000-1
1-125-137 High:1st CPM:A5:Middle
Speed
1-125-138 High:2nd CPM:A5:Middle
Speed
1-125-140 High:1st CPM:B6:Middle
Speed
1-125-141 High:2nd CPM:B6:Middle
Speed
1-125-143 High:1st CPM:A6:Middle
Speed
1-125-144 High:2nd CPM:A6:Middle
Speed
1-125-145 High:1st CPM:SRA3:Large
Size:Middle Speed
1-125-146 High:2nd CPM:SRA3:Large
Size:Middle Speed
1-125-147 High:1st CPM:SRA3:Small
Size:Middle Speed
1-125-148 High:2nd CPM:SRA3:Small
Size:Middle Speed
1-125-201 High:1st CPM:A3:Large
Size:Low Speed
1-125-204 High:1st CPM:A3:Small
Size:Low Speed
1-125-207 High:1st CPM:DLT:Large
Size:Low Speed
1-125-210 High:1st CPM:DLT:Small
Size:Low Speed
1-125-213 High:1st CPM:B4:Large
Size:Low Speed
1-125-216 High:1st CPM:B4:Small
Size:Low Speed
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 60 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 50 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
117
118
3. Engine SP Mode Tables
1-125-219 High:1st CPM:LT:Large
Size:Low Speed
1-125-222 High:1st CPM:LT:Small
Size:Low Speed
1-125-225 High:1st CPM:A4:Large
Size:Low Speed
1-125-228 High:1st CPM:A4:Small
Size:Low Speed
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
1-125-231 High:1st CPM:B5:Large
Size:Low Speed
1-125-234 High:1st CPM:B5:Small
Size:Low Speed
*ENG [0 to 100 / 80 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step]
1-125-237 High:1st CPM:A5:Low Speed *ENG [0 to 100 / 80 / 1%/step]
1-125-240 High:1st CPM:B6:Low Speed *ENG [0 to 100 / 83 / 1%/step]
1-125-243 High:1st CPM:A6:Low Speed *ENG [0 to 100 / 93 / 1%/step]
*ENG [0 to 100 / 80 / 1%/step] 1-125-244 High:1st CPM:SRA3:Large
Size:Low Speed
1-125-245 High:1st CPM:SRA3:Small
Size:Low Speed
*ENG [0 to 100 / 80 / 1%/step]
1126 [Heating Start Delay]
1-126-001 Judgement Temp 1
1-126-002 Judgement Temp 2
1-126-003 Judgement Temp 3
1-126-011 Set TimeA: Div 1
1-126-012 Set TimeA: Div 2
*ENG [0 to 180 / 30 / 1deg/step]
*ENG [0 to 180 / 32 / 1deg/step]
*ENG [0 to 180 / 45 / 1deg/step]
*ENG [0 to 10000 / * / 1msec/step]
*NA: 1100, EU: 1500, Asia: 1500,
CHN: 1500, TWN: 1100, KOR: 1500
*ENG [0 to 10000 / * / 1msec/step]
*NA: 1600, EU: 2200, Asia: 2200,
CHN: 2200, TWN: 1600, KOR: 2200
Engine SP Tables - SP1000-1
1-126-013 Set TimeA: Div 3
1-126-014 Set TimeA: Div 4
1-126-021 Delay Time: Div 1
1-126-022 Delay Time: Div 2
1-126-023 Delay Time: Div 3
1-126-024 Delay Time: Div 4
*ENG [0 to 10000 / * / 1msec/step]
*NA: 1900, EU: 2500, Asia: 2500,
CHN: 2500, TWN: 1900, KOR: 2500
*ENG [0 to 10000 / * / 1msec/step]
*NA: 1100, EU: 1500, Asia: 1500,
CHN: 1500, TWN: 1100, KOR: 1500
*ENG [0 to 10000 / * / 1msec/step]
*NA: 1100, EU: 1500, Asia: 1500,
CHN: 1500, TWN: 1100, KOR: 1500
*ENG [0 to 10000 / * / 1msec/step]
*NA: 1600, EU: 2200, Asia: 2200,
CHN: 2200, TWN: 1600, KOR: 2200
*ENG [0 to 10000 / * / 1msec/step]
*NA: 1900, EU: 2500, Asia: 2500,
CHN: 2500, TWN: 1900, KOR: 2500
*ENG [0 to 10000 / * / 1msec/step]
*NA: 1100, EU: 1500, Asia: 1500,
CHN: 1500, TWN: 1100, KOR: 1500
1127 [Energy Saving PprFeed Judgment]
1-127-001 Judging Method Change ENG [0 to 2 / 1 / 1/step]
1-127-002 Temp.: Threshold: Press ENG [0 to 200 / 50 / 1deg/step]
1-127-003 Temp.: Threshold: Atmosphere ENG [0 to 200 / 60 / 1deg/step]
1-127-004 Power Supply Voltage: Lower ENG [0 to 300 / * / 1V/step]
*NA: 108, EU: 206, Asia: 206, CHN:
206, TWN: 102 , KOR: 206
1-127-005 Power Supply Voltage: Upper
1-127-006 Judgment Time-Out
ENG [0 to 300 / * / 1V/step]
*NA: 134, EU: 252, Asia: 252, CHN:
252, TWN: 121 , KOR: 252
ENG [0 to 10.0 / 10.0 / 0.1sec/step]
119
120
3. Engine SP Mode Tables
1131 [Continuous Print Mode Switch]
1-131-001 Feed Permit Condition *ENG [0 to 2 / 1 / 1/step]
0: Productivity Mode
1: Fusing Quality Mode
2: Fusing Quality Mode 2
1132 [Maximum Duty Switch]
1-132-001 Control Method Switch *ENG [0 or 1 / 1 / 1/step]
0: Fixed Duty
1: AutoOffstCtl
1133 [Voltage Detection]
1-133-001 Heater ON
1-133-002 Max
1-133-003 Min
1-133-004 Last
1-133-005 SC
1-133-006 Threshold Voltage
*ENG [0 to 350.0 / * / 0.1V/step]
*NA: 116.0, EU: 223.0, Asia: 223.0,
CHN: 223.0, TWN: 107.0 , KOR:
223.0
*ENG [0 to 350.0 / 0 / 0.1V/step]
*ENG [0 to 350.0 / 350.0 / 0.1V/step]
*ENG [0 to 350.0 / 0 / 0.1V/step]
*ENG [0 to 350.0 / 0 / 0.1V/step]
*ENG [0 to 255 / * / 1V/step]
*NA: 96, EU: 178, Asia: 178, CHN:
178, TWN: 88 , KOR: 178
1134 [Effective Duty Adjustment]
1-134-001 Control Method Switch *ENG [0 or 1 / 1 / 1/step]
0: OFF
1: ON
1135 [Inrush Control]
Engine SP Tables - SP1000-1
1-135-001 Inrush Control *ENG [0 or 1 / 0 / 1/step]
0: Normal (Do not)
1: Inrush current suppress (Do)
1135 [Inrush Control]
1-135-002 Flicker Control *ENG [0 or 1 / 0 / 1/step]
1141 [Fusing SC Error Time Info]
1-141-001 SC Number
1-141-101 Htg Roller:Ctr Det1
1-141-102 Htg Roller:End Det1
1-141-103 Press Roller:Ctr Det1
1-141-104 Press Roller:End Det1
1-141-105 NC Sensor: Center Atmosphere
Temp 1
1-141-106 NC Sensor: End Atmosphere
Temp 1
1-141-151 Htg Roller:Ctr Det2
1-141-152 Htg Roller:End Det2
1-141-153 Press Roller:Ctr Det2
1-141-154 Press Roller:End Det2
1-141-155 NC Sensor: Center Atmosphere
Temp 2
1-141-156 NC Sensor: End Atmosphere
Temp 2
1-141-201 Htg Roller:Ctr Det3
1-141-202 Htg Roller:End Det3
1-141-203 Press Roller:Ctr Det3
1-141-204 Press Roller:End Det3
*ENG [0 to 99999 / 0 / 1/step]
*ENG [-100 to 300 / 0 / 1deg/step]
*ENG [-100 to 300 / 0 / 1deg/step]
*ENG [-100 to 300 / 0 / 1deg/step]
*ENG [-100 to 300 / 0 / 1deg/step]
*ENG [-100 to 300 / 0 / 1deg/step]
*ENG [-100 to 300 / 0 / 1deg/step]
*ENG [-100 to 300 / 0 / 1deg/step]
*ENG [-100 to 300 / 0 / 1deg/step]
*ENG [-100 to 300 / 0 / 1deg/step]
*ENG [-100 to 300 / 0 / 1deg/step]
*ENG [-100 to 300 / 0 / 1deg/step]
*ENG [-100 to 300 / 0 / 1deg/step]
*ENG [-100 to 300 / 0 / 1deg/step]
*ENG [-100 to 300 / 0 / 1deg/step]
*ENG [-100 to 300 / 0 / 1deg/step]
*ENG [-100 to 300 / 0 / 1deg/step]
121
122
3. Engine SP Mode Tables
1-141-205 NC Sensor: Center Atmosphere
Temp 3
1-141-206 NC Sensor: End Atmosphere
Temp 3
*ENG [-100 to 300 / 0 / 1deg/step]
*ENG
[-100 to 300 / 0 / 1deg/step]
1142 [Fusing Jam Detection]
1-142-001 SC Display *ENG [0 or 1 / 0 / 1/step]
0: OFF
1: ON
1151 [Pressure Setting]
1-151-001 Pressure Change ON/OFF
1-151-002 Pressure Time1
1-151-003 Pressure Time2
1-151-005 Depressure Time
1-151-010 Shift Time:Energy Saving
1-151-011 Shift Time
1-151-051 Rotary speed
1-151-101 Pressure:Plain1/2
1-151-102 Pressure:Thin
1-151-103 Pressure:M-thick
1-151-104 Pressure:Thick1
1-151-105 Pressure:Thick2
1-151-106 Pressure:Thick3
1-151-107 Pressure:Special1
1-151-108 Pressure:Special2
*ENG [0 or 1 / 1 / 1/step]
0: OFF
1: ON
*ENG [0 to 10000 / 70 / 10msec/step]
*ENG [0 to 10000 / 70 / 10msec/step]
*ENG [0 to 10000 / 0 / 10msec/step]
*ENG [0 to 3600 / 0 / 1sec/step]
*ENG [0 to 3600 / 60 / 1sec/step]
*ENG [-12.8 to 12.7 / 0 / 0.1%/step]
*ENG [0 to 3 / 2 / 1/step]
*ENG [0 to 3 / 2 / 1/step]
*ENG [0 to 3 / 2 / 1/step]
*ENG [0 to 3 / 2 / 1/step]
*ENG [0 to 3 / 2 / 1/step]
*ENG [0 to 3 / 2 / 1/step]
*ENG [0 to 3 / 2 / 1/step]
*ENG [0 to 3 / 2 / 1/step]
Engine SP Tables - SP1000-1
1-151-109 Pressure:Special3 *ENG [0 to 3 / 2 / 1/step]
1-151-110 Pressure:Envelope *ENG [0 to 3 / 2 / 1/step]
1-151-151 Pressure:Plain1/2:Low Speed *ENG [0 to 3 / 2 / 1/step]
1-151-152 Pressure:M-thick:Low Speed
1-151-153 Pressure:Thick1:Low Speed
*ENG [0 to 3 / 2 / 1/step]
*ENG [0 to 3 / 2 / 1/step]
1-151-154 Pressure:Special1:Low Speed *ENG [0 to 3 / 2 / 1/step]
1-151-157 Pressure:M-thick:Glossy *ENG [0 to 3 / 2 / 1/step]
1-151-158 Pressure:OHP *ENG [0 to 3 / 2 / 1/step]
1-151-159 Pressure:Envelope:Low Speed *ENG [0 to 3 / 2 / 1/step]
1-151-160 Pressure:Thin:Low Speed
1-151-161 Pressure:Thick4
1-151-162 Pressure:Postcard
*ENG [0 to 3 / 2 / 1/step]
*ENG [0 to 3 / 2 / 1/step]
*ENG [0 to 3 / 2 / 1/step]
1152 [Fusing Nip Band Check]
1-152-001 Execute
1-152-002 Pre-idling Time
1-152-003 Stop Time
1-152-004 Pressure Position
ENG [0 or 1 / 0 / 1/step]
*ENG [0 to 999 / 300 / 1sec/step]
*ENG [0 to 100 / 20 / 1sec/step]
*ENG [1 to 2 / 2 / 1/step]
1153 [Abnormal Noise Confirmation]
1-153-001 Unit: Execute
1-153-002 No Unit: Execute
1-153-003 Operation Line Speed
1-153-004 Operation Time
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 to 2 / 0 / 1/step]
0: Std Speed
1: Mid Speed
2: Low Speed
ENG [0 to 240 / 60 / 1sec/step]
123
124
3. Engine SP Mode Tables
1-153-005 Heat Center Target Temp
1-153-006 Heat End Target Temp
1-153-007 Press Target Temp
1154 [Switch:Rotation Start/Stop]
1-154-001 Judging Method Change
ENG [100 to 180 / 130 / 1deg/step]
ENG [100 to 180 / 130 / 1deg/step]
ENG [0 to 200 / 0 / 1deg/step]
1-154-005 Heater ON Timing
1-154-006 Overshoot Prevent Temp.:SC
1155 [Small Size Paper Control]
1-155-001 Print Width
*ENG [0 or 1 / 0 / 1/step]
0: On
1: Off
*ENG [0 to 250 / 50 / 1 / 10msec/step]
*ENG [0 to 250 / 180 / 1deg/step]
*ENG [0 to 300 / 0 / 1mm/step]
1157 [Overshoot Prevent Control]
1-157-001 Decision Time
1-157-002 Decision Temp.
1-157-003 -
1-157-004 Timeout
1161 [Shading Plate Control]
1-161-001 Judgment Temp A
1-161-002 Judgment Temp B
1-161-003 Position Transition Time
1-161-004 After Transition Time Out
1-161-005 Shading Plate Retry Volume
1162 [Shading Plate Control]
*ENG [0 to 100 / 5 / 1sec/step]
*ENG [0 to 250 / 185 / 1deg/step]
*ENG [0 to 300 / 15 / 1sec/step]
*ENG [0 to 300 / 300 / 1sec/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 10000 / 1000 / 1msec/step]
ENG [0 to 20000 / 0 / 1msec/step]
*ENG [0 to 100 / 60 / 1pulse/step]
Engine SP Tables - SP1000-1
1-162-001 Shading Position Temp: 12inch:
1
1-162-002 Shading Position Temp: 12inch:
2
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
1-162-003 Shading Position Temp: 12inch:
3
1-162-004 Shading Position Temp: A3: 1
ENG [0 to 250 / 250 / 1deg/step]
1-162-005 Shading Position Temp: A3: 2
1-162-006 Shading Position Temp: A3: 3
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
1-162-007 Shading Position Temp: DLT: 1 ENG [0 to 250 / 250 / 1deg/step]
1-162-008 Shading Position Temp: DLT: 2 ENG [0 to 250 / 250 / 1deg/step]
1-162-009 Shading Position Temp: DLT: 3 ENG [0 to 250 / 250 / 1deg/step]
1-162-010 Shading Position Temp: B4: 1 ENG [0 to 250 / 250 / 1deg/step]
1-162-011 Shading Position Temp: B4: 2
1-162-012 Shading Position Temp: B4: 3
1-162-013 Shading Position Temp: LT: 1
1-162-014 Shading Position Temp: LT: 2
1-162-015 Shading Position Temp: LT: 3
1-162-016 Shading Position Temp: A4: 1
1-162-017 Shading Position Temp: A4: 2
1-162-018 Shading Position Temp: A4: 3
1-162-019 Shading Position Temp: B5: 1
1-162-020 Shading Position Temp: B5: 2
1-162-021 Shading Position Temp: B5: 3
1-162-022 Shading Position Temp: A5: 1
1-162-023 Shading Position Temp: A5: 2
1-162-024 Shading Position Temp: A5: 3
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
125
126
3. Engine SP Mode Tables
1-162-025 Shading Position Temp: B6: 1
1-162-026 Shading Position Temp: B6: 2
1-162-027 Shading Position Temp: B6: 3
1-162-028 Shading Position Temp: DLEnv:
1
1-162-029 Shading Position Temp: DLEnv:
2
1-162-030 Shading Position Temp: DLEnv:
3
1-162-031 Shading Position Temp:
COM10: 1
1-162-032 Shading Position Temp:
COM10: 2
1-162-033 Shading Position Temp:
COM10: 3
1-162-034 Shading Position Temp:
Postcard: 1
1-162-035 Shading Position Temp:
Postcard: 2
1-162-036 Shading Position Temp:
Postcard: 3
1-162-037 Shading Position Temp: 12inch:
4
1-162-038 Shading Position Temp: 12inch:
5
1-162-039 Shading Position Temp: 12inch:
6
1-162-040 Shading Position Temp: 12inch:
7
1-162-041 Shading Position Temp: 12inch:
8
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
Engine SP Tables - SP1000-1
1-162-042 Shading Position Temp: A3: 4
1-162-043 Shading Position Temp: A3: 5
1-162-044 Shading Position Temp: A3: 6
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
1-162-045 Shading Position Temp: A3: 7
1-162-046 Shading Position Temp: A3: 8
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
1-162-047 Shading Position Temp: DLT: 4 ENG [0 to 250 / 250 / 1deg/step]
1-162-048 Shading Position Temp: DLT: 5 ENG [0 to 250 / 250 / 1deg/step]
1-162-049 Shading Position Temp: DLT: 6 ENG [0 to 250 / 250 / 1deg/step]
1-162-050 Shading Position Temp: DLT: 7 ENG [0 to 250 / 250 / 1deg/step]
1-162-051 Shading Position Temp: DLT: 8 ENG [0 to 250 / 250 / 1deg/step]
1-162-052 Shading Position Temp: B4: 4 ENG [0 to 250 / 250 / 1deg/step]
1-162-053 Shading Position Temp: B4: 5
1-162-054 Shading Position Temp: B4: 6
1-162-055 Shading Position Temp: B4: 7
1-162-056 Shading Position Temp: B4: 8
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
1-162-057 Shading Position Temp: LT: 4
1-162-058 Shading Position Temp: LT: 5
1-162-059 Shading Position Temp: LT: 6
1-162-060 Shading Position Temp: LT: 7
1-162-061 Shading Position Temp: LT: 8
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
1-162-062 Shading Position Temp: A4: 4
1-162-063 Shading Position Temp: A4: 5
1-162-064 Shading Position Temp: A4: 6
1-162-065 Shading Position Temp: A4: 7
1-162-066 Shading Position Temp: A4: 8
1-162-067 Shading Position Temp: B5: 4
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
127
128
3. Engine SP Mode Tables
1-162-068 Shading Position Temp: B5: 5
1-162-069 Shading Position Temp: B5: 6
1-162-070 Shading Position Temp: B5: 7
1-162-071 Shading Position Temp: B5: 8
1-162-072 Shading Position Temp: A5: 4
1-162-073 Shading Position Temp: A5: 5
1-162-074 Shading Position Temp: A5: 6
1-162-075 Shading Position Temp: A5: 7
1-162-076 Shading Position Temp: A5: 8
1-162-077 Shading Position Temp: B6: 4
1-162-078 Shading Position Temp: B6: 5
1-162-079 Shading Position Temp: B6: 6
1-162-080 Shading Position Temp: B6: 7
1-162-081 Shading Position Temp: B6: 8
1-162-082 Shading Position Temp: DLEnv:
4
1-162-083 Shading Position Temp: DLEnv:
5
1-162-084 Shading Position Temp: DLEnv:
6
1-162-085 Shading Position Temp: DLEnv:
7
1-162-086 Shading Position Temp: DLEnv:
8
1-162-087 Shading Position Temp:
COM10: 4
1-162-088 Shading Position Temp:
COM10: 5
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
Engine SP Tables - SP1000-1
1-162-089 Shading Position Temp:
COM10: 6
1-162-090 Shading Position Temp:
COM10: 7
1-162-091 Shading Position Temp:
COM10: 8
1-162-092 Shading Position Temp:
Postcard: 4
1-162-093 Shading Position Temp:
Postcard: 5
1-162-094 Shading Position Temp:
Postcard: 6
1-162-095 Shading Position Temp:
Postcard: 7
1-162-096 Shading Position Temp:
Postcard: 8
1-162-121 Shading Position Temp: SRA3:
1
1-162-122 Shading Position Temp: SRA3:
2
1-162-123 Shading Position Temp: SRA3:
3
1-162-124 Shading Position Temp: SRA3:
4
1-162-125 Shading Position Temp: SRA3:
5
1-162-126 Shading Position Temp: SRA3:
6
1-162-127 Shading Position Temp: SRA3:
7
1-162-128 Shading Position Temp: SRA3:
8
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
ENG [0 to 250 / 250 / 1deg/step]
129
130
3. Engine SP Mode Tables
1-162-201 Shading Position Temp: 12inch:
Clear
1-162-202 Shading Position Temp: A3:
Clear
1-162-203 Shading Position Temp: DLT:
Clear
1-162-204 Shading Position Temp: B4:
Clear
1-162-205 Shading Position Temp: LT:
Clear
1-162-206 Shading Position Temp: A4:
Clear
1-162-207 Shading Position Temp: B5:
Clear
1-162-208 Shading Position Temp: A5:
Clear
1-162-209 Shading Position Temp: B6:
Clear
1-162-210 Shading Position Temp: DLEnv:
Clear
1-162-211 Shading Position Temp:
COM10: Clear
1-162-212 Shading Position Temp:
Postcard: Clear
1-162-213 Shading Position Temp: SRA3:
Clear
ENG [0 to 250 / 0 / 1deg/step]
ENG [0 to 250 / 0 / 1deg/step]
ENG [0 to 250 / 0 / 1deg/step]
ENG [0 to 250 / 0 / 1deg/step]
ENG [0 to 250 / 0 / 1deg/step]
ENG [0 to 250 / 0 / 1deg/step]
ENG [0 to 250 / 0 / 1deg/step]
ENG [0 to 250 / 0 / 1deg/step]
ENG [0 to 250 / 0 / 1deg/step]
ENG [0 to 250 / 0 / 1deg/step]
ENG [0 to 250 / 0 / 1deg/step]
ENG [0 to 250 / 0 / 1deg/step]
ENG
[0 to 250 / 0 / 1deg/step]
1163 [Shading Plate Control]
1-163-001 Shading Position Time: 12inch:
1
1-163-002 Shading Position Time: 12inch:
2
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
Engine SP Tables - SP1000-1
1-163-003 Shading Position Time: 12inch:
3
1-163-004 Shading Position Time: A3: 1
1-163-005 Shading Position Time: A3: 2
1-163-006 Shading Position Time: A3: 3
1-163-007 Shading Position Time: DLT: 1
1-163-008 Shading Position Time: DLT: 2
1-163-009 Shading Position Time: DLT: 3
1-163-010 Shading Position Time: B4: 1
1-163-011 Shading Position Time: B4: 2
1-163-012 Shading Position Time: B4: 3
1-163-013 Shading Position Time: LT: 1
1-163-014 Shading Position Time: LT: 2
1-163-015 Shading Position Time: LT: 3
1-163-016 Shading Position Time: A4: 1
1-163-017 Shading Position Time: A4: 2
1-163-018 Shading Position Time: A4: 3
1-163-019 Shading Position Time: B5: 1
1-163-020 Shading Position Time: B5: 2
1-163-021 Shading Position Time: B5: 3
1-163-022 Shading Position Time: A5: 1
1-163-023 Shading Position Time: A5: 2
1-163-024 Shading Position Time: A5: 3
1-163-025 Shading Position Time: B6: 1
1-163-026 Shading Position Time: B6: 2
1-163-027 Shading Position Time: B6: 3
ENG [0 to 10000 / 10000 / 1sec/step]
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
[0 to 10000 / 10000 / 1sec/step]
[0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
[0 to 10000 / 10000 / 1sec/step]
[0 to 10000 / 10000 / 1sec/step]
[0 to 10000 / 10000 / 1sec/step]
131
132
3. Engine SP Mode Tables
1-163-028 Shading Position Time: DLEnv:
1
1-163-029 Shading Position Time: DLEnv:
2
1-163-030 Shading Position Time: DLEnv:
3
1-163-031 Shading Position Time:
COM10: 1
1-163-032 Shading Position Time:
COM10: 2
1-163-033 Shading Position Time:
COM10: 3
1-163-034 Shading Position Time:
Postcard: 1
1-163-035 Shading Position Time:
Postcard: 2
1-163-036 Shading Position Time:
Postcard: 3
1-163-037 Shading Position Time: 12inch:
4
1-163-038 Shading Position Time: 12inch:
5
1-163-039 Shading Position Time: 12inch:
6
1-163-040 Shading Position Time: 12inch:
7
1-163-041 Shading Position Time: 12inch:
8
1-163-042 Shading Position Time: A3: 4
1-163-043 Shading Position Time: A3: 5
1-163-044 Shading Position Time: A3: 6
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
Engine SP Tables - SP1000-1
1-163-045 Shading Position Time: A3: 7
1-163-046 Shading Position Time: A3: 8
1-163-047 Shading Position Time: DLT: 4
1-163-048 Shading Position Time: DLT: 5
1-163-049 Shading Position Time: DLT: 6
1-163-050 Shading Position Time: DLT: 7
1-163-051 Shading Position Time: DLT: 8
1-163-052 Shading Position Time: B4: 4
1-163-053 Shading Position Time: B4: 5
1-163-054 Shading Position Time: B4: 6
1-163-055 Shading Position Time: B4: 7
1-163-056 Shading Position Time: B4: 8
1-163-057 Shading Position Time: LT: 4
1-163-058 Shading Position Time: LT: 5
1-163-059 Shading Position Time: LT: 6
1-163-060 Shading Position Time: LT: 7
1-163-061 Shading Position Time: LT: 8
1-163-062 Shading Position Time: A4: 4
1-163-063 Shading Position Time: A4: 5
1-163-064 Shading Position Time: A4: 6
1-163-065 Shading Position Time: A4: 7
1-163-066 Shading Position Time: A4: 8
1-163-067 Shading Position Time: B5: 4
1-163-068 Shading Position Time: B5: 5
1-163-069 Shading Position Time: B5: 6
1-163-070 Shading Position Time: B5: 7
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
133
134
3. Engine SP Mode Tables
1-163-071 Shading Position Time: B5: 8
1-163-072 Shading Position Time: A5: 4
1-163-073 Shading Position Time: A5: 5
1-163-074 Shading Position Time: A5: 6
1-163-075 Shading Position Time: A5: 7
1-163-076 Shading Position Time: A5: 8
1-163-077 Shading Position Time: B6: 4
1-163-078 Shading Position Time: B6: 5
1-163-079 Shading Position Time: B6: 6
1-163-080 Shading Position Time: B6: 7
1-163-081 Shading Position Time: B6: 8
1-163-082 Shading Position Time: DLEnv:
4
1-163-083 Shading Position Time: DLEnv:
5
1-163-084 Shading Position Time: DLEnv:
6
1-163-085 Shading Position Time: DLEnv:
7
1-163-086 Shading Position Time: DLEnv:
8
1-163-087 Shading Position Time:
COM10: 4
1-163-088 Shading Position Time:
COM10: 5
1-163-089 Shading Position Time:
COM10: 6
1-163-090 Shading Position Time:
COM10: 7
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
ENG [0 to 10000 / 10000 / 1sec/step]
Engine SP Tables - SP1000-1
1-163-091 Shading Position Time:
COM10: 8
1-163-092 Shading Position Time:
Postcard: 4
1-163-093 Shading Position Time:
Postcard: 5
1-163-094 Shading Position Time:
Postcard: 6
ENG
ENG
ENG
ENG
[0 to 10000 / 10000 / 1sec/step]
[0 to 10000 / 10000 / 1sec/step]
[0 to 10000 / 10000 / 1sec/step]
[0 to 10000 / 10000 / 1sec/step]
1-163-095 Shading Position Time:
Postcard: 7
1-163-096 Shading Position Time:
Postcard: 8
ENG
ENG
[0 to 10000 / 10000 / 1sec/step]
[0 to 10000 / 10000 / 1sec/step]
1-163-121 Shading Position Time: SRA3: 1 ENG [0 to 10000 / 10000 / 1sec/step]
1-163-122 Shading Position Time: SRA3: 2 ENG [0 to 10000 / 10000 / 1sec/step]
1-163-123 Shading Position Time: SRA3: 3 ENG [0 to 10000 / 10000 / 1sec/step]
1-163-124 Shading Position Time: SRA3: 4 ENG [0 to 10000 / 10000 / 1sec/step]
1-163-125 Shading Position Time: SRA3: 5 ENG [0 to 10000 / 10000 / 1sec/step]
1-163-126 Shading Position Time: SRA3: 6 ENG [0 to 10000 / 10000 / 1sec/step]
1-163-127 Shading Position Time: SRA3: 7 ENG [0 to 10000 / 10000 / 1sec/step]
1-163-128 Shading Position Time: SRA3: 8 ENG [0 to 10000 / 10000 / 1sec/step]
1-163-131 Shading Position Time: ECO: 1 ENG [0 to 10000 / 10000 / 1sec/step]
1-163-132 Shading Position Time: ECO: 2 ENG [0 to 10000 / 10000 / 1sec/step]
1-163-133 Shading Position Time: ECO: 3 ENG [0 to 10000 / 10000 / 1sec/step]
1-163-134 Shading Position Time: ECO: 4 ENG [0 to 10000 / 10000 / 1sec/step]
1-163-135 Shading Position Time: ECO: 5 ENG [0 to 10000 / 10000 / 1sec/step]
1-163-136 Shading Position Time: ECO: 6 ENG [0 to 10000 / 10000 / 1sec/step]
1-163-137 Shading Position Time: ECO: 7 ENG [0 to 10000 / 10000 / 1sec/step]
1-163-138 Shading Position Time: ECO: 8 ENG [0 to 10000 / 10000 / 1sec/step]
135
136
3. Engine SP Mode Tables
1164 [Shading Plate Control]
1-164-001 Shading Position: 12inch: 1
1-164-002 Shading Position: 12inch: 2
1-164-003 Shading Position: 12inch: 3
1-164-004 Shading Position: A3: 1
1-164-005 Shading Position: A3: 2
1-164-006 Shading Position: A3: 3
1-164-007 Shading Position: DLT: 1
1-164-008 Shading Position: DLT: 2
1-164-009 Shading Position: DLT: 3
1-164-010 Shading Position: B4: 1
1-164-011 Shading Position: B4: 2
1-164-012 Shading Position: B4: 3
1-164-013 Shading Position: LT: 1
1-164-014 Shading Position: LT: 2
1-164-015 Shading Position: LT: 3
1-164-016 Shading Position: A4: 1
1-164-017 Shading Position: A4: 2
1-164-018 Shading Position: A4: 3
1-164-019 Shading Position: B5: 1
1-164-020 Shading Position: B5: 2
1-164-021 Shading Position: B5: 3
1-164-022 Shading Position: A5: 1
1-164-023 Shading Position: A5: 2
1-164-024 Shading Position: A5: 3
1-164-025 Shading Position: B6: 1
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
Engine SP Tables - SP1000-1
1-164-026 Shading Position: B6: 2
1-164-027 Shading Position: B6: 3
1-164-028 Shading Position: DLEnv: 1
1-164-029 Shading Position: DLEnv: 2
1-164-030 Shading Position: DLEnv: 3
1-164-031 Shading Position: COM10: 1
1-164-032 Shading Position: COM10: 2
1-164-033 Shading Position: COM10: 3
1-164-034 Shading Position: Postcard: 1
1-164-035 Shading Position: Postcard: 2
1-164-036 Shading Position: Postcard: 3
1-164-037 Shading Position: 12inch: 4
1-164-038 Shading Position: 12inch: 5
1-164-039 Shading Position: 12inch: 6
1-164-040 Shading Position: 12inch: 7
1-164-041 Shading Position: 12inch: 8
1-164-042 Shading Position: A3: 4
1-164-043 Shading Position: A3: 5
1-164-044 Shading Position: A3: 6
1-164-045 Shading Position: A3: 7
1-164-046 Shading Position: A3: 8
1-164-047 Shading Position: DLT: 4
1-164-048 Shading Position: DLT: 5
1-164-049 Shading Position: DLT: 6
1-164-050 Shading Position: DLT: 7
1-164-051 Shading Position: DLT: 8
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
137
138
3. Engine SP Mode Tables
1-164-052 Shading Position: B4: 4
1-164-053 Shading Position: B4: 5
1-164-054 Shading Position: B4: 6
1-164-055 Shading Position: B4: 7
1-164-056 Shading Position: B4: 8
1-164-057 Shading Position: LT: 4
1-164-058 Shading Position: LT: 5
1-164-059 Shading Position: LT: 6
1-164-060 Shading Position: LT: 7
1-164-061 Shading Position: LT: 8
1-164-062 Shading Position: A4: 4
1-164-063 Shading Position: A4: 5
1-164-064 Shading Position: A4: 6
1-164-065 Shading Position: A4: 7
1-164-066 Shading Position: A4: 8
1-164-067 Shading Position: B5: 4
1-164-068 Shading Position: B5: 5
1-164-069 Shading Position: B5: 6
1-164-070 Shading Position: B5: 7
1-164-071 Shading Position: B5: 8
1-164-072 Shading Position: A5: 4
1-164-073 Shading Position: A5: 5
1-164-074 Shading Position: A5: 6
1-164-075 Shading Position: A5: 7
1-164-076 Shading Position: A5: 8
1-164-077 Shading Position: B6: 4
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
Engine SP Tables - SP1000-1
1-164-078 Shading Position: B6: 5
1-164-079 Shading Position: B6: 6
1-164-080 Shading Position: B6: 7
1-164-081 Shading Position: B6: 8
1-164-082 Shading Position: DLEnv: 4
1-164-083 Shading Position: DLEnv: 5
1-164-084 Shading Position: DLEnv: 6
1-164-085 Shading Position: DLEnv: 7
1-164-086 Shading Position: DLEnv: 8
1-164-087 Shading Position: COM10: 4
1-164-088 Shading Position: COM10: 5
1-164-089 Shading Position: COM10: 6
1-164-090 Shading Position: COM10: 7
1-164-091 Shading Position: COM10: 8
1-164-092 Shading Position: Postcard: 4
1-164-093 Shading Position: Postcard: 5
1-164-094 Shading Position: Postcard: 6
1-164-095 Shading Position: Postcard: 7
1-164-096 Shading Position: Postcard: 8
1-164-121 Shading Position: SRA3: 1
1-164-122 Shading Position: SRA3: 2
1-164-123 Shading Position: SRA3: 3
1-164-124 Shading Position: SRA3: 4
1-164-125 Shading Position: SRA3: 5
1-164-126 Shading Position: SRA3: 6
1-164-127 Shading Position: SRA3: 7
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
ENG [0 to 1000 / 0 / 1pluse/step]
139
140
3. Engine SP Mode Tables
1-164-128 Shading Position: SRA3: 8
1165 [Shading Plate Control]
1-165-001 Execution Judgement
1-165-101 Continuous Error Times
ENG [0 to 1000 / 0 / 1pluse/step]
*ENG [0 or 1 / 0 / 1/step]
0: ON
1: OFF
*ENG [0 to 10 / 0 / 1/step]
Engine SP Tables - SP1000-2
1801 [Relay Motor Speed Adjust]
1-801-001 Feed CCW:Plain:Low
1-801-002 Feed CCW:Plain:Std
1-801-003 Feed CCW:Mid-thick:Low
1-801-004 Feed CCW:Mid-thick:Std
1-801-005 Feed CCW:Thick 1:Low
1-801-006 Feed CCW:Thick 1:Mid
1-801-007 Feed CCW:Thick 2:Low
1-801-008 Feed CCW:Thick 3:Low
1-801-009 Feed CCW:Thick 4:Low
1-801-010 Feed CW:Plain:Low
1-801-011 Feed CW:Plain:Std
1-801-012 Feed CW:Mid-thick:Low
1-801-013 Feed CW:Mid-thick:Std
1-801-014 Feed CW:Thick 1:Low
1-801-015 Feed CW:Thick 1:Mid
1-801-016 Feed CW:Thick 2:Low
1-801-017 Feed CW:Thick 3:Low
1-801-018 Feed CW:Thick 4:Low
1-801-019 Vertical Feed:Plain:Low
1-801-020 Vertical Feed:Plain:Std
1-801-021 Vertical Feed:Mid-thick:Low
*ENG [-2 to 2 / 0.9 / 0.1%/step]
*ENG [-2 to 2 / 0.9 / 0.1%/step]
*ENG [-2 to 2 / 1.1 / 0.1%/step]
*ENG [-2 to 2 / 1.1 / 0.1%/step]
*ENG [-2 to 2 / 1.2 / 0.1%/step]
*ENG [-2 to 2 / 1.2 / 0.1%/step]
*ENG [-2 to 2 / 1.2 / 0.1%/step]
*ENG [-2 to 2 / 0.9 / 0.1%/step]
*ENG [-2 to 2 / 0.9 / 0.1%/step]
*ENG [-2 to 2 / 0.9 / 0.1%/step]
*ENG [-2 to 2 / 0.9 / 0.1%/step]
*ENG [-2 to 2 / 1.1 / 0.1%/step]
*ENG [-2 to 2 / 1.1 / 0.1%/step]
*ENG [-2 to 2 / 1.2 / 0.1%/step]
*ENG [-2 to 2 / 1.2 / 0.1%/step]
*ENG [-2 to 2 / 1.2 / 0.1%/step]
*ENG [-2 to 2 / 0.9 / 0.1%/step]
*ENG [-2 to 2 / 0.9 / 0.1%/step]
*ENG [-2 to 2 / 0.9 / 0.1%/step]
*ENG [-2 to 2 / 0.9 / 0.1%/step]
*ENG [-2 to 2 / 1.1 / 0.1%/step]
141
142
3. Engine SP Mode Tables
1-801-022 Vertical Feed:Mid-thick:Std
1-801-023 Vertical Feed:Thick 1:Low
1-801-024 Vertical Feed:Thick 1:Mid
1-801-025 Vertical Feed:Thick 2:Low
1-801-026 Vertical Feed:Thick 3:Low
1-801-027 Vertical Feed:Thick 4:Low
1-801-028 Registration:Plain:Low
1-801-029 Registration:Plain:Std
1-801-030 Registration:Mid-thick:Low
1-801-031 Registration:Mid-thick:Std
1-801-032 Registration:Thick 1:Low
1-801-033 Registration:Thick1:Mid
1-801-034 Registration:Thick 2:Low
1-801-035 Registration:Thick 3:Low
1-801-036 Registration:Thick 4:Low
1-801-037 Exit CCW:Plain:Low
1-801-038 Exit CCW:Plain:Std
1-801-039 Exit CCW:Mid-thick:Low
1-801-040 Exit CCW:Mid-thick:Std
1-801-041 Exit CCW:Thick1:Low
1-801-042 Exit CCW:Thick1:Mid
1-801-043 Exit CCW:Thick2:Low
1-801-044 Exit CCW:Thick3:Low
1-801-045 Exit CCW:Thick4:Low
1-801-046 Reverse CW:Plain:Low
1-801-047 Reverse CW:Plain:Std
*ENG [-2 to 2 / 1.1 / 0.1%/step]
*ENG [-2 to 2 / 1.2 / 0.1%/step]
*ENG [-2 to 2 / 1.2 / 0.1%/step]
*ENG [-2 to 2 / 1.2 / 0.1%/step]
*ENG [-2 to 2 / 0.9 / 0.1%/step]
*ENG [-2 to 2 / 0.9 / 0.1%/step]
*ENG [-2 to 2 / 0.3 / 0.1%/step]
*ENG [-2 to 2 / 0.3 / 0.1%/step]
*ENG [-2 to 2 / 0.3 / 0.1%/step]
*ENG [-2 to 2 / 0.3 / 0.1%/step]
*ENG [-2 to 2 / 0.4 / 0.1%/step]
*ENG [-2 to 2 / 0.4 / 0.1%/step]
*ENG [-2 to 2 / 0.4 / 0.1%/step]
*ENG [-2 to 2 / 0.3 / 0.1%/step]
*ENG [-2 to 2 / 0.3 / 0.1%/step]
*ENG [-4 to 4 / -0.8 / 0.1%/step]
*ENG [-4 to 4 / -0.8 / 0.1%/step]
*ENG [-4 to 4 / -0.8 / 0.1%/step]
*ENG [-4 to 4 / -0.8 / 0.1%/step]
*ENG [-4 to 4 / -0.8 / 0.1%/step]
*ENG [-4 to 4 / -0.6 / 0.1%/step]
*ENG [-4 to 4 / -0.9 / 0.1%/step]
*ENG [-4 to 4 / -0.9 / 0.1%/step]
*ENG [-4 to 4 / -0.4 / 0.1%/step]
*ENG [-4 to 4 / 0.7 / 0.1%/step]
*ENG [-4 to 4 / 0.7 / 0.1%/step]
Engine SP Tables - SP1000-2
1-801-048 Reverse CW:Mid-thick:Low
1-801-049 Reverse CW:Mid-thick:Std
1-801-050 Reverse CW:Thick1:Low
1-801-051 Reverse CW:Thick1:Mid
1-801-052 Reverse CW:Thick2:Low
1-801-053 Reverse CW:Thick3:Low
1-801-054 Reverse CW:Thick4:Low
1-801-055 Reverse CCW:Plain:Low
1-801-056 Reverse CCW:Plain:Std
1-801-057 Reverse CCW:Mid-thick:Low
1-801-058 Reverse CCW:Mid-thick:Std
1-801-059 Reverse CCW:Thick1:Low
1-801-060 Reverse CCW:Thick1:Mid
1-801-061 Reverse CCW:Thick2:Low
1-801-062 Reverse CCW:Thick3:Low
*ENG [-4 to 4 / 0.5 / 0.1%/step]
*ENG [-4 to 4 / 0.5 / 0.1%/step]
*ENG [-4 to 4 / 0.7 / 0.1%/step]
*ENG [-4 to 4 / 0.7 / 0.1%/step]
*ENG [-4 to 4 / 0.8 / 0.1%/step]
*ENG [-4 to 4 / 0.7 / 0.1%/step]
*ENG [-4 to 4 / 0.7 / 0.1%/step]
*ENG [-4 to 4 / -0.8 / 0.1%/step]
*ENG [-4 to 4 / -0.8 / 0.1%/step]
*ENG [-4 to 4 / -0.8 / 0.1%/step]
*ENG [-4 to 4 / -0.8 / 0.1%/step]
*ENG [-4 to 4 / -0.8 / 0.1%/step]
*ENG [-4 to 4 / -0.6 / 0.1%/step]
*ENG [-4 to 4 / -0.9 / 0.1%/step]
*ENG [-4 to 4 / -0.9 / 0.1%/step]
1-801-063 Reverse CCW:Thick4:Low
1-801-064 Duplex Enter CW:Plain:Low
1-801-065 Duplex Enter CW:Plain:Std
1-801-066 Duplex Enter CW:Midthick:Low
*ENG [-4 to 4 / -0.4 / 0.1%/step]
*ENG [-4 to 4 / 1.4 / 0.1%/step]
*ENG [-4 to 4 / 1.4 / 0.1%/step]
*ENG [-4 to 4 / 1.2 / 0.1%/step]
1-801-067 Duplex Enter CW:Mid-thick:Std *ENG [-4 to 4 / 1.2 / 0.1%/step]
1-801-068 Duplex Enter CW:Thick1:Low *ENG [-4 to 4 / 1.5 / 0.1%/step]
1-801-069 Duplex Enter CW:Thick1:Mid *ENG [-4 to 4 / 1.5 / 0.1%/step]
1-801-070 Duplex Enter CW:Thick2:Low *ENG [-4 to 4 / 1.5 / 0.1%/step]
1-801-071 Duplex Enter CW:Thick3:Low
1-801-072 Duplex CW:Plain:Low
*ENG [-4 to 4 / 1.4 / 0.1%/step]
*ENG [-4 to 4 / 0.7 / 0.1%/step]
143
144
3. Engine SP Mode Tables
1-801-073 Duplex CW:Plain:Std
1-801-074 Duplex CW:Mid-thick:Low
1-801-075 Duplex CW:Mid-thick:Std
1-801-076 Duplex CW:Thick1:Low
1-801-077 Duplex CW:Thick1:Mid
1-801-078 Duplex CW:Thick2:Low
1-801-079 Duplex CW:Thick3:Low
1-801-080 Duplex CCW:Plain:Low
1-801-081 Duplex CCW:Plain:Std
1-801-082 Duplex CCW:Mid-thick:Low
1-801-083 Duplex CCW:Mid-thick:Std
1-801-084 Duplex CCW:Thick1:Low
1-801-085 Duplex CCW:Thick1:Mid
1-801-086 Duplex CCW:Thick2:Low
1-801-087 Duplex CCW:Thick3:Low
*ENG [-4 to 4 / 0.7 / 0.1%/step]
*ENG [-4 to 4 / 0.5 / 0.1%/step]
*ENG [-4 to 4 / 0.5 / 0.1%/step]
*ENG [-4 to 4 / 0.8 / 0.1%/step]
*ENG [-4 to 4 / 0.8 / 0.1%/step]
*ENG [-4 to 4 / 0.8 / 0.1%/step]
*ENG [-4 to 4 / 0.7 / 0.1%/step]
*ENG [-4 to 4 / 0.9 / 0.1%/step]
*ENG [-4 to 4 / 0.9 / 0.1%/step]
*ENG [-4 to 4 / 1.1 / 0.1%/step]
*ENG [-4 to 4 / 1.1 / 0.1%/step]
*ENG [-4 to 4 / 1.2 / 0.1%/step]
*ENG [-4 to 4 / 1.2 / 0.1%/step]
*ENG [-4 to 4 / 1.2 / 0.1%/step]
*ENG [-4 to 4 / 0.9 / 0.1%/step]
1-801-088 Duplex CCW:Thick4:Low *ENG [-4 to 4 / 0.9 / 0.1%/step]
1-801-089 Relay Motor Speed Adjust:Low *ENG [-4 to 4 / 0 / 0.1%/step]
1-801-090 Relay Motor Speed Adjust:Mid *ENG [-4 to 4 / 0 / 0.1%/step]
1-801-091 Relay Motor Speed
Adjust:Standard
*ENG [-4 to 4 / 0 / 0.1%/step]
1-801-100 Drum Adjust *ENG [0 or 1 / 1 / 1/step]
1-801-101 Offset:ColorOpcMot:Standard *ENG [-10 to 10 / 0 / 0.01Hz/step]
1-801-102 Offset:ColorOpcMot:Mid
1-801-103 Offset:ColorOpcMot:Low
1-801-106 ColorOpcMot:Standard
1-801-107 ColorOpcMot:Mid
*ENG [-10 to 10 / 0 / 0.01Hz/step]
*ENG [-10 to 10 / 0 / 0.01Hz/step]
*ENG [-10 to 10 / 0 / 0.01Hz/step]
*ENG [-10 to 10 / 0 / 0.01Hz/step]
Engine SP Tables - SP1000-2
1-801-108 ColorOpcMot:Low
1-801-109 BkDevMot:Standard
1-801-110 BkDevMot:Mid
1-801-111 BkDevMot:Low
1-801-115 ColorDevMot:Standard
1-801-116 ColorDevMot:Mid
1-801-117 ColorDevMot:Low
*ENG [-10 to 10 / 0 / 0.01Hz/step]
*ENG [-20 to 20 / 0 / 0.1%/step]
*ENG [-20 to 20 / 0 / 0.1%/step]
*ENG [-20 to 20 / 0 / 0.1%/step]
*ENG [-20 to 20 / 0 / 0.1%/step]
*ENG [-20 to 20 / 0 / 0.1%/step]
*ENG [-20 to 20 / 0 / 0.1%/step]
1-801-118 Fusing:Standard
1-801-119 Fusing:Mid
1-801-120 Fusing:Low
1-801-121 Fusing:Low:1200:Plain
*ENG [-10 to 10 / -1.4 / 0.1%/step]
*ENG [-10 to 10 / -1.0 / 0.1%/step]
*ENG [-10 to 10 / -1.0 / 0.1%/step]
*ENG [-10 to 10 / -1.4 / 0.1%/step]
1-801-122 OPCTransferMot:Standard
1-801-123 OPCTransferMot:Mid
*ENG [-10 to 10 / 0.2 / 0.1%/step]
*ENG [-10 to 10 / 0.2 / 0.1%/step]
1-801-124 OPCTransferMot:Low
1-801-125 Fusing:Low:Thick 4
*ENG [-10 to 10 / 0.2 / 0.1%/step]
*ENG [-10 to 10 / -0.5 / 0.1%/step]
1-801-133 ColorOpcMot:Standard:indepe ndence
*ENG [-10 to 10 / -0.2 / 0.1%/step]
*ENG [-10 to 10 / -0.2 / 0.1%/step] 1-801-134 ColorOpcMot:Mid:independen ce
1-801-135 ColorOpcMot:Low:independen ce
1-801-140 Long:Registration:Plain:Low
*ENG [-10 to 10 / -0.2 / 0.1%/step]
*ENG [-2 to 2 / 0.3 / 0.1%/step]
*ENG [-2 to 2 / 0.3 / 0.1%/step] 1-801-141 Long:Registration:Plain:High
1-801-142 Long:Registration:Middle
Thick:Low
*ENG [-2 to 2 / 0.3 / 0.1%/step]
1-801-143 Long:Registration:Middle
Thick:High
*ENG [-2 to 2 / 0.3 / 0.1%/step]
1-801-144 Long:Registration:Thick 1:Low *ENG [-2 to 2 / 0.4 / 0.1%/step]
145
146
3. Engine SP Mode Tables
1-801-145 Long:Registration:Thick
1:Middle
*ENG [-2 to 2 / 0.4 / 0.1%/step]
1-801-146 Long:Registration:Thick 2:Low *ENG [-2 to 2 / 0.4 / 0.1%/step]
1-801-147 Long:Registration:Thick 3:Low *ENG [-2 to 2 / 0.3 / 0.1%/step]
1-801-148 Long:Registration:Thick 4:Low *ENG [-2 to 2 / 0.3 / 0.1%/step]
1-801-160 Long:Fusing:Plain:Low
1-801-161 Long:Fusing:Plain:High
*ENG [-10 to 10 / -1.2 / 0.01%/step]
*ENG [-10 to 10 / -1.4 / 0.01%/step]
1-801-162 Long:Fusing:Middle Thick:Low *ENG [-10 to 10 / -0.8 / 0.01%/step]
1-801-163 Long:Fusing:Middle Thick:High *ENG [-10 to 10 / -1.4 / 0.01%/step]
1-801-164 Long:Fusing:Thick 1:Low
1-801-165 Long:Fusing:Thick 1:Middle
1-801-166 Long:Fusing:Thick 2:Low
1-801-167 Long:Fusing:Thick 3:Low
1-801-168 Long:Fusing:Thick 4:Low
1-801-180 Long:Exit CCW:Plain:Low
1-801-181 Long:Exit CCW:Plain:High
1-801-182 Long:Exit CCW:Middle
Thick:Low
*ENG [-10 to 10 / -0.8 / 0.01%/step]
*ENG [-10 to 10 / -0.8 / 0.01%/step]
*ENG [-10 to 10 / -0.8 / 0.01%/step]
*ENG [-10 to 10 / -0.8 / 0.01%/step]
*ENG [-10 to 10 / -0.8 / 0.01%/step]
*ENG [-4 to 4 / -0.8 / 0.1%/step]
*ENG [-4 to 4 / -0.8 / 0.1%/step]
*ENG [-4 to 4 / -0.8 / 0.1%/step]
1-801-183 Long:Exit CCW:Middle
Thick:High
*ENG [-4 to 4 / -0.8 / 0.1%/step]
1-801-184 Long:Exit CCW:Thick 1:Low *ENG [-4 to 4 / -0.8 / 0.1%/step]
1-801-185 Long:Exit CCW:Thick 1:Middle *ENG [-4 to 4 / -0.6 / 0.1%/step]
1-801-186 Long:Exit CCW:Thick 2:Low
1-801-187 Long:Exit CCW:Thick 3:Low
1-801-188 Long:Exit CCW:Thick 4:Low
*ENG [-4 to 4 / -0.9 / 0.1%/step]
*ENG [-4 to 4 / -0.9 / 0.1%/step]
*ENG [-4 to 4 / -0.9 / 0.1%/step]
1805 [Motor Gain Adj.]
Engine SP Tables - SP1000-2
1-805-050 DuplexInM:Speed Detective
Gain
*ENG [0 to 200 / 100 / 0.01%/step]
1-805-051 DuplexInM:Position Loop Gain *ENG [0 to 200 / 50 / 0.01%/step]
1-805-052 DuplexInM:Proportio*NAl
Gain:PID
*ENG [0 to 200 / 50 / 0.01%/step]
1-805-053 DuplexInM:Integral Gain:PID *ENG [0 to 200 / 50 / 0.01%/step]
1-805-054 DuplexInM:Derivative Gain:PID *ENG [0 to 200 / 50 / 0.01%/step]
1-805-055 DuplexInM:Derivative Gain:FF *ENG [0 to 200 / 100 / 0.01%/step]
1-805-056 DuplexInM:Proportio*NAl
Gain:FF
*ENG [0 to 200 / 100 / 0.01%/step]
1-805-057 DuplexInM:Offset:FF
1-805-058 DuplexInM:Numerator
Coefficient:LPF:B0
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
1-805-059 DuplexInM:Denomi*NAtor
Coefficient:LPF:A1
1-805-060 DuplexInM:Denomi*NAtor
Coefficient:LPF:A2
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
1-805-061 DuplexM:Speed Detective
Gain
*ENG [0 to 200 / 100 / 0.01%/step]
1-805-062 DuplexM:Position Loop Gain
1-805-063 DuplexM:Proportio*NAl
Gain:PID
1-805-064 DuplexM:Integral Gain:PID
*ENG [0 to 200 / 50 / 0.01%/step]
*ENG [0 to 200 / 50 / 0.01%/step]
*ENG [0 to 200 / 50 / 0.01%/step]
1-805-065 DuplexM:Derivative Gain:PID *ENG [0 to 200 / 50 / 0.01%/step]
1-805-066 DuplexM:Derivative Gain:FF
1-805-067 DuplexM:Proportio*NAl
Gain:FF
1-805-068 DuplexM:Offset:FF
1-805-069 DuplexM:Numerator
Coefficient:LPF:B0
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
147
148
3. Engine SP Mode Tables
1-805-070 DuplexM:Denomi*NAtor
Coefficient:LPF:A1
1-805-071 DuplexM:Denomi*NAtor
Coefficient:LPF:A2
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
1-805-072 DuplexM:Speed Detective
Gain
1-805-073 DuplexM:Position Loop Gain
*ENG [0 to 200 / 100 / 0.01%/step]
1-805-074 DuplexM:Proportio*NAl
Gain:PID
*ENG [0 to 200 / 50 / 0.01%/step]
*ENG [0 to 200 / 50 / 0.01%/step]
1-805-075 DuplexM:Integral Gain:PID *ENG [0 to 200 / 50 / 0.01%/step]
1-805-076 DuplexM:Derivative Gain:PID *ENG [0 to 200 / 50 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
1-805-077 DuplexM:Derivative Gain:FF
1-805-078 DuplexM:Proportio*NAl
Gain:FF
1-805-079 DuplexM:Offset:FF
1-805-080 DuplexM:Numerator
Coefficient:LPF:B0
1-805-081 DuplexM:Denomi*NAtor
Coefficient:LPF:A1
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
1-805-082 DuplexM:Denomi*NAtor
Coefficient:LPF:A2
1-805-115 DuplexInM:Proportio*NAl
Gain:PID
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
1-805-116 DuplexInM:Integral Gain:PID *ENG [0 to 200 / 100 / 0.01%/step]
1-805-117 DuplexInM:Derivative Gain:PID *ENG [0 to 200 / 100 / 0.01%/step]
1-805-118 DuplexM:Proportio*NAl
Gain:PID
1-805-119 DuplexM:Integral Gain:PID
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
1-805-120 DuplexM:Derivative Gain:PID *ENG [0 to 200 / 100 / 0.01%/step]
Engine SP Tables - SP1000-2
1-805-121 DuplexM:Proportio*NAl
Gain:PID
*ENG [0 to 200 / 100 / 0.01%/step]
1-805-122 DuplexM:Integral Gain:PID *ENG [0 to 200 / 100 / 0.01%/step]
1-805-123 DuplexM:Derivative Gain:PID *ENG [0 to 200 / 100 / 0.01%/step]
1806 [Motor Speed Profile]
1-806-020 DuplexInM:Acceleration1
1-806-021 DuplexInM:Deceleration1
1-806-022 DuplexInM:Acceleration2
1-806-023 DuplexInM:Deceleration2
1-806-024 DuplexM:Acceleration1
1-806-025 DuplexM:Deceleration1
1-806-026 DuplexM:Acceleration2
1-806-027 DuplexM:Deceleration2
1-806-028 DuplexM:Acceleration1
1-806-029 DuplexM:Deceleration1
1-806-030 DuplexM:Acceleration2
1-806-031 DuplexM:Deceleration2
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
*ENG [0 to 200 / 100 / 0.01%/step]
1902 [Drum Phase Adj.]
1-902-001 Execute ENG [0 or 1 / 0 / 1/step]
1907 [Paper Feed Timing Adj.]
1-907-001 Feed Solenoid ON:Tray1:Plain *ENG [-20 to 20 / 0 / 1mm/step]
1-907-002 Feed Solenoid ON:Tray1:Thick *ENG [-20 to 20 / 0 / 1mm/step]
1-907-003 Feed Solenoid ON:Tray2:Plain *ENG [-20 to 20 / 0 / 1mm/step]
1-907-004 Feed Solenoid ON:Tray2:Thick *ENG [-20 to 20 / 0 / 1mm/step]
149
150
3. Engine SP Mode Tables
1-907-005 Feed DCM OFF:Tray1:Plain
1-907-006 Feed DCM OFF:Tray1:Thick
1-907-007 Feed DCM OFF:Tray2:Plain
*ENG [-20 to 20 / 0 / 1mm/step]
*ENG [-20 to 20 / 0 / 1mm/step]
*ENG [-20 to 20 / 0 / 1mm/step]
1-907-008 Feed DCM OFF:Tray2:Thick *ENG [-20 to 20 / 0 / 1mm/step]
1-907-009 Feed Solenoid OFF:Tray1:Plain *ENG [-20 to 20 / 0 / 1mm/step]
1-907-010 Feed Solenoid OFF:Tray1:Thick *ENG [-20 to 20 / 0 / 1mm/step]
1-907-011 Feed Solenoid OFF:Tray2:Plain *ENG [-20 to 20 / 0 / 1mm/step]
1-907-012 Feed Solenoid OFF:Tray2:Thick *ENG [-20 to 20 / 0 / 1mm/step]
1-907-013 Feed Start:Tray1:Plain *ENG [-20 to 20 / 0 / 1mm/step]
1-907-014 Feed Start:Tray1:Thick
1-907-015 Feed Start:Tray2:Plain
*ENG [-20 to 20 / 0 / 1mm/step]
*ENG [-20 to 20 / 0 / 1mm/step]
1-907-016 Feed Start:Tray2:Thick
1-907-017 Feed Re-Start:Tray1:Plain
1-907-018 Feed Re-Start:Tray1:Thick
1-907-019 Feed Re-Start:Tray2:Plain
*ENG [-20 to 20 / 0 / 1mm/step]
*ENG [-20 to 20 / 0 / 1mm/step]
*ENG [-20 to 20 / 0 / 1mm/step]
*ENG [-20 to 20 / 0 / 1mm/step]
1-907-020 Feed Re-Start:Tray2:Thick
1-907-021 Feed Re2-Start:Tray2:Plain
1-907-022 Feed Re2-Start:Tray2:Thick
1-907-023 Registration DCM OFF:Plain
1-907-024 Registration DCM OFF:Thick
*ENG [-20 to 20 / 0 / 1mm/step]
*ENG [-20 to 20 / 0 / 1mm/step]
*ENG [-20 to 20 / 0 / 1mm/step]
*ENG [-5 to 5 / 0 / 0.1mm/step]
*ENG [-5 to 5 / 0 / 0.1mm/step]
1-907-025 By-pass Solenoid ON:Low
1-907-026 By-pass Solenoid ON:Mid
1-907-027 By-pass Solenoid ON:Std
1-907-028 By-pass Solenoid OFF
1-907-029 By-pass Size Decision Timing
1-907-030 Duplex DCM OFF:Low
*ENG [0 to 40 / 0 / 1mm/step]
*ENG [0 to 40 / 0 / 1mm/step]
ENG [0 to 40 / 0 / 1mm/step]
*ENG [0 to 40 / 0 / 1mm/step]
*ENG [1 to 3 / 3 / 1/step]
*ENG [-10 to 10 / 0 / 1mm/step]
Engine SP Tables - SP1000-2
1-907-031 Duplex DCM OFF:Mid *ENG [-10 to 10 / 0 / 1mm/step]
1-907-032 Duplex DCM OFF:Std ENG [-10 to 10 / 0 / 1mm/step]
1-907-033 ExitPaperJunction SOL ON:Low *ENG [-10 to 10 / 0 / 1mm/step]
1-907-034 ExitPaperJunction SOL ON:Mid *ENG [-10 to 10 / 0 / 1mm/step]
1-907-035 ExitPaperJunction SOL ON:Std ENG [-10 to 10 / 0 / 1mm/step]
*ENG [-10 to 10 / 0 / 1mm/step] 1-907-036 ExitPaperJunction SOL
OFF:Low
1-907-037 ExitPaperJunction SOL
OFF:Mid
*ENG [-10 to 10 / 0 / 1mm/step]
1-907-038 ExitPaperJunction SOL OFF:Std ENG [-10 to 10 / 0 / 1mm/step]
1-907-039 Reverse Position:Plain *ENG [-10 to 10 / 0 / 1mm/step]
1-907-040 Reverse Position:Thick
1-907-041 Duplex Enter Position:Plain
*ENG [-10 to 10 / 0 / 1mm/step]
ENG [-10 to 10 / 0 / 1mm/step]
1-907-042 Duplex Enter Position:Thick ENG [-10 to 10 / 0 / 1mm/step]
1-907-043 Duplex Re-Feed Position:Plain *ENG [-10 to 10 / 0 / 1mm/step]
1-907-044 Duplex Re-Feed Position:Thick *ENG [-10 to 10 / 0 / 1mm/step]
1-907-045 ExitM:Accelerate
Position:Normal Speed
ENG [-5 to 15 / 0 / 1mm/step]
ENG [-5 to 15 / 0 / 1mm/step] 1-907-046 ExitM:Accelerate
Position:Middle Speed
1-907-047 ExitM:Accelerate Position:Low
Speed
ENG [-5 to 15 / 0 / 1mm/step]
1-907-048 ExitM:Accelerate Position:Low:
1200:Plain
ENG [-5 to 15 / 0 / 1mm/step]
1-907-061 Feed Solenoid ON:Tray3:Plain ENG [-20 to 20 / 0 / 1mm/step]
1-907-062 Feed Solenoid ON:Tray3:Thick ENG [-20 to 20 / 0 / 1mm/step]
1-907-063 Feed Solenoid ON:Tray4:Plain ENG [-20 to 20 / 0 / 1mm/step]
1-907-064 Feed Solenoid ON:Tray4:Thick ENG [-20 to 20 / 0 / 1mm/step]
151
152
3. Engine SP Mode Tables
1-907-065 Feed Solenoid
ON:Tray5(LCT):Plain
1-907-066 Feed Solenoid
ON:Tray5(LCT):Thick
1-907-067 Feed DCM OFF:Tray3:Plain
1-907-068 Feed DCM OFF:Tray3:Thick
1-907-069 Feed DCM OFF:Tray4:Plain
ENG
ENG
[-20 to 20 / 0 / 1mm/step]
[-20 to 20 / 0 / 1mm/step]
ENG [-20 to 20 / 0 / 1mm/step]
ENG [-20 to 20 / 0 / 1mm/step]
ENG [-20 to 20 / 0 / 1mm/step]
1-907-070 Feed DCM OFF:Tray4:Thick
1-907-071 Feed DCM
OFF:Tray5(LCT):Plain
ENG
ENG
[-20 to 20 / 0 / 1mm/step]
[-20 to 20 / 0 / 1mm/step]
1-907-072 Feed DCM
OFF:Tray5(LCT):Thick
ENG [-20 to 20 / 0 / 1mm/step]
1-907-073 Feed Solenoid OFF:Tray3:Plain ENG [-20 to 20 / 0 / 1mm/step]
1-907-074 Feed Solenoid OFF:Tray3:Thick ENG [-20 to 20 / 0 / 1mm/step]
1-907-075 Feed Solenoid OFF:Tray4:Plain ENG [-20 to 20 / 0 / 1mm/step]
1-907-076 Feed Solenoid OFF:Tray4:Thick ENG [-20 to 20 / 0 / 1mm/step]
1-907-077 Feed Solenoid
OFF:Tray5(LCT):Plain
ENG [-20 to 20 / 0 / 1mm/step]
1-907-078 Feed Solenoid
OFF:Tray5(LCT):Thick
ENG [-20 to 20 / 0 / 1mm/step]
1-907-079 Feed Start:Tray3:Plain
1-907-080 Feed Start:Tray3:Thick
1-907-081 Feed Start:Tray4:Plain
1-907-082 Feed Start:Tray4:Thick
ENG
ENG
ENG
ENG
[-20 to 20 / 0 / 1mm/step]
[-20 to 20 / 0 / 1mm/step]
[-20 to 20 / 0 / 1mm/step]
[-20 to 20 / 0 / 1mm/step]
1-907-083 Feed Start:Tray5(LCT):Plain
1-907-084 Feed Start:Tray5(LCT):Thick
ENG
ENG
[-20 to 20 / 0 / 1mm/step]
[-20 to 20 / 0 / 1mm/step]
1-907-085 ExitLineSpdUp EndPos:StdSpd *ENG [-30 to 15 / 0 / 1mm/step]
1-907-086 ExitLineSpdUp EndPos:MidSpd *ENG [-30 to 15 / 0 / 1mm/step]
Engine SP Tables - SP1000-2
1-907-087 ExitLineSpdUp EndPos:LowSpd *ENG [-30 to 15 / 0 / 1mm/step]
1-907-088 ExitLineSpdUp EndPos:LowSpd:
1200:Plain
*ENG [-30 to 15 / 0 / 1mm/step]
1-907-090 Fusing Exit SOL ON: LowSpd *ENG [-15 to 15 / 0 / 1mm/step]
1-907-091 Fusing Exit SOL ON: MidSpd *ENG [-15 to 15 / 0 / 1mm/step]
1-907-092 Fusing Exit SOL ON: StdSpd *ENG [-15 to 15 / 0 / 1mm/step]
1-907-093 Fusing Exit SOL OFF: LowSpd *ENG [-15 to 15 / 0 / 1mm/step]
1-907-094 Fusing Exit SOL OFF: MidSpd *ENG [-15 to 15 / 0 / 1mm/step]
1-907-095 Fusing Exit SOL OFF: StdSpd *ENG [-15 to 15 / 0 / 1mm/step]
1907 [Operating Setting]
1-907-096 Fusing Exit SOL Setting *ENG [0 to 6 / 0 / 1/step]
1907 [Paper Feed Timing Adj.]
1-907-097 Feed Re-Start:Tray3:Plain
1-907-098 Feed Re-Start:Tray3:Thick
1-907-099 Feed Re-Start:Tray4:Plain
*ENG [-20 to 20 / 0 / 1mm/step]
*ENG [-20 to 20 / 0 / 1mm/step]
*ENG [-20 to 20 / 0 / 1mm/step]
1-907-100 Feed Re-Start:Tray4:Thick *ENG [-20 to 20 / 0 / 1mm/step]
1-907-101 Feed Re-Start:Tray5(LCT):Plain *ENG [-20 to 20 / 0 / 1mm/step]
1-907-102 Feed Re-Start:Tray5(LCT):Thick *ENG [-20 to 20 / 0 / 1mm/step]
1-907-103 Feed Re2-Start:Tray3:Plain *ENG [-20 to 20 / 0 / 1mm/step]
1-907-104 Feed Re2-Start:Tray3:Thick
1-907-105 Feed Re2-Start:Tray4:Plain
1-907-106 Feed Re2-Start:Tray4:Thick
1-907-107 Feed Re2-
Start:Tray5(LCT):Plain
1-907-108 Feed Re2-
Start:Tray5(LCT):Thick
*ENG [-20 to 20 / 0 / 1mm/step]
*ENG [-20 to 20 / 0 / 1mm/step]
*ENG [-20 to 20 / 0 / 1mm/step]
*ENG [-20 to 20 / 0 / 1mm/step]
*ENG [-20 to 20 / 0 / 1mm/step]
153
154
3. Engine SP Mode Tables
1-907-109 Manual Feed Regist. Stop
Timing: Env
ENG [0 to 40 / 0 / 1mm/step]
1908 [Paper Feed Length]
1-908-001 Feed Solenoid ON:Tray1:Plain ENG [-99 to 99 / 0 / 1mm/step]
1-908-002 Feed Solenoid ON:Tray1:Thick ENG [-99 to 99 / 0 / 1mm/step]
1-908-003 Feed Solenoid ON:Tray2:Plain ENG [-99 to 99 / 0 / 1mm/step]
1-908-004 Feed Solenoid ON:Tray2:Thick ENG [-99 to 99 / 0 / 1mm/step]
1-908-005 Feed DCM OFF:Tray1:Plain
1-908-006 Feed DCM OFF:Tray1:Thick
ENG [-99 to 99 / 0 / 1mm/step]
ENG [-99 to 99 / 0 / 1mm/step]
1-908-007 Feed DCM OFF:Tray2:Plain
1-908-008 Feed DCM OFF:Tray2:Thick
ENG
ENG
[-99 to 99 / 0 / 1mm/step]
[-99 to 99 / 0 / 1mm/step]
1-908-009 Feed Solenoid OFF:Tray1:Plain ENG [-99 to 99 / 0 / 1mm/step]
1-908-010 Feed Solenoid OFF:Tray1:Thick ENG [-99 to 99 / 0 / 1mm/step]
1950 [Fan Cooling Time Set]
1-950-003 Dev Cooling Fan
1-950-005 Ozone Fan
1-950-006 Fusing Fan
1-950-007 Paper Exit Cooling Fan
1-950-011 PSU Cooling Fan
1-950-051 Dev Suction Fan: Right
1951 [Fan Start Time Set]
1-951-003 Dev Cooling Fan
1-951-005 Ozone Fan
1-951-006 Fusing Fan
*ENG [0 to 120 / 0 / 1min/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG [0 to 900 / 120 / 1sec/step]
*ENG [0 to 900 / 0 / 1sec/step]
*ENG [0 to 900 / 120 / 1sec/step]
Engine SP Tables - SP1000-2
1-951-007 Paper Exit Cooling Fan
1-951-011 PSU Cooling Fan
1-951-051 Dev Suction Fan: Right
*ENG [0 to 900 / 120 / 1sec/step]
*ENG [0 to 900 / 120 / 1sec/step]
*ENG [0 to 900 / 0 / 1sec/step]
1952
1-952-001 -
[Fan Control Off Mode Time Set]
*ENG [0 to 60 / 10 / 1min/step]
1953 [Extra Fan Control]
1-953-001 Extra Fan Cooling State
1-953-002 Execution Temp. Threshold
1-953-003 Cancellation Temp. Threshold
1-953-004 Extra Fan Operation ON/OFF
Setting
*ENG [0 or 1 / 0 / 1/step]
0: Disable
1: enable
*ENG [0 to 100 / 38.5 / 0.1deg/step]
*ENG [0 to 100 / 2 / 0.1deg/step]
*ENG [0 or 1 / 1 / 1/step]
0: disable
1: enable
1955 [Fan Control]
1-955-004 Dev Cooling Fan Op Sw Temp *ENG [0 to 100 / 36 / 0.1deg/step]
*ENG [0 to 100 / 12 / 0.1deg/step] 1-955-006 Paper Exit Cooling Fan Op Sw
Temp
1-955-007 Fusing Fan Op Sw Temp *ENG [0 to 100 / 0 / 0.1deg/step]
*ENG [0 to 100 / 35 / 0.1deg/step] 1-955-009 Ozone Fan Low Speed Op Sw
Temp
1-955-010 Ozone Fan Middle Speed Op
Sw Temp
*ENG [0 to 100 / 37 / 0.1deg/step]
1-955-011 Ozone Fan High Speed Op Sw
Temp
1-955-012 Ozone Fan Low Noise Op
DUTY
*ENG [0 to 100 / 40 / 0.1deg/step]
*ENG [0 to 100 / 20 / 1%/step]
155
156
3. Engine SP Mode Tables
1-955-013 Ozone Fan Low Speed Op
DUTY
1-955-014 Ozone Fan Middle Speed Op
DUTY
1-955-015 Ozone Fan High Speed Op
DUTY
1-955-016 Paper Exit Cooling Fan Op
Start Time A
1-955-017 PSU Cooling Fan Op Start Time
A
1-955-018 Fan Op Sw Temp Thers
1-955-019 Paper Exit Cooling Fan Control
Off Mode Time
1-955-020 PSU Cooling Fan Control Off
Mode Time
1-955-051 Dev Suction Fan: Right Op Sw
Temp
1-955-062 Dev Suction Fan: Right Op Start
Time
1-955-063 Paper Exit Cooling Fan Op
Start Time B
1-955-064 PSU Cooling Fan Op Start Time
B
1-955-065 PSU Cooling Fan Op Start Time
C
*ENG [0 to 100 / 30 / 1%/step]
*ENG [0 to 100 / 40 / 1%/step]
*ENG [0 to 100 / 40 / 1%/step]
*ENG [0 to 900 / 300 / 1sec/step]
*ENG [0 to 900 / 300 / 1sec/step]
*ENG [0 to 100 / 2 / 0.1deg/step]
*ENG [0 to 3600 / 600 / 1sec/step]
*ENG [0 to 3600 / 600 / 1sec/step]
*ENG [0 to 100 / 36 / 0.1deg/step]
*ENG [0 to 900 / 300 / 1sec/step]
*ENG [0 to 900 / 300 / 1sec/step]
*ENG [0 to 900 / 300 / 1sec/step]
1-955-066 PSU Cooling Fan Op Start Time
D
1-955-071 Ozone Fan Extra Op DUTY
*ENG [0 to 900 / * / 1sec/step]
*NA: 300, EU: 120, Asia: 120, CHN:
120, TWN: 300, KOR: 120
*ENG [0 to 900 / * / 1sec/step]
*NA: 300, EU: 120, Asia: 120, CHN:
120, TWN: 300, KOR: 120
*ENG [0 to 100 / 20 / 1%/step]
Engine SP Tables - SP2000-1
2005 [Charge DC Voltage: Fixed]
2-005-001 Standard Speed: K
2-005-002 Standard Speed: C
2-005-003 Standard Speed: M
2-005-004 Standard Speed: Y
2-005-005 Middle Speed: K
2-005-006 Middle Speed: C
2-005-007 Middle Speed: M
2-005-008 Middle Speed: Y
2-005-009 Low Speed: K
2-005-010 Low Speed: C
2-005-011 Low Speed: M
2-005-012 Low Speed: Y
2005 [Charge DC Voltage: Correction]
2-005-013 PCU: Standard Speed
2-005-014 PCU: Middle Speed
2-005-015 PCU: Low Speed
2-005-018 Correction Coefficient a: K
2-005-019 Correction Coefficient a: C
2-005-020 Correction Coefficient a: M
2-005-021 Correction Coefficient a: Y
2-005-022 Correction Coefficient b: K
*ENG [0 to 2000 / 1350 / 10-V/step]
*ENG [0 to 2000 / 1350 / 10-V/step]
*ENG [0 to 2000 / 1350 / 10-V/step]
*ENG [0 to 2000 / 1350 / 10-V/step]
*ENG [0 to 2000 / 1350 / 10-V/step]
*ENG [0 to 2000 / 1350 / 10-V/step]
*ENG [0 to 2000 / 1350 / 10-V/step]
*ENG [0 to 2000 / 1350 / 10-V/step]
*ENG [0 to 2000 / 1350 / 10-V/step]
*ENG [0 to 2000 / 1350 / 10-V/step]
*ENG [0 to 2000 / 1350 / 10-V/step]
*ENG [0 to 2000 / 1350 / 10-V/step]
*ENG [-100 to 100 / 0 / 1-V/step]
*ENG [-100 to 100 / 0 / 1-V/step]
*ENG [-100 to 100 / 0 / 1-V/step]
*ENG [0 to 2 / 1 / 0.001/step]
*ENG [0 to 2 / 1 / 0.001/step]
*ENG [0 to 2 / 1 / 0.001/step]
*ENG [0 to 2 / 1 / 0.001/step]
*ENG [0 to 2000 / 700 / 1-V/step]
157
158
3. Engine SP Mode Tables
2-005-023 Correction Coefficient b: C
2-005-024 Correction Coefficient b: M
2-005-025 Correction Coefficient b: Y
2-005-026 Correction Coefficient c: K
2-005-027 Correction Coefficient c: C
2-005-028 Correction Coefficient c: M
2-005-029 Correction Coefficient c: Y
2-005-030 Temperature Threshold L: K
2-005-031 Temperature Threshold L: C
2-005-032 Temperature Threshold L: M
2-005-033 Temperature Threshold L: Y
2-005-034 Temperature Threshold M: K
2-005-035 Temperature Threshold M: C
2-005-036 Temperature Threshold M: M
2-005-037 Temperature Threshold M: Y
2-005-038 Temperature Threshold H: K
2-005-039 Temperature Threshold H: C
2-005-040 Temperature Threshold H: M
2-005-041 Temperature Threshold H: Y
2-005-043 DC Bias Fixed Value Set
*ENG [0 to 2000 / 700 / 1-V/step]
*ENG [0 to 2000 / 700 / 1-V/step]
*ENG [0 to 2000 / 700 / 1-V/step]
*ENG [0 to 100 / 0 / 1-V/step]
*ENG [0 to 100 / 0 / 1-V/step]
*ENG [0 to 100 / 0 / 1-V/step]
*ENG [0 to 100 / 0 / 1-V/step]
*ENG [0 to 99 / 15 / 1deg/step]
*ENG [0 to 99 / 15 / 1deg/step]
*ENG [0 to 99 / 16 / 1deg/step]
*ENG [0 to 99 / 16 / 1deg/step]
*ENG [0 to 99 / 22 / 1deg/step]
*ENG [0 to 99 / 22 / 1deg/step]
*ENG [0 to 99 / 23 / 1deg/step]
*ENG [0 to 99 / 23 / 1deg/step]
*ENG [0 to 99 / 28 / 1deg/step]
*ENG [0 to 99 / 28 / 1deg/step]
*ENG [0 to 99 / 29 / 1deg/step]
*ENG [0 to 99 / 29 / 1deg/step]
*ENG [0 or 1 / 0 / 1/step]
2-005-044 Correction Coefficient a: Fixed K
2-005-045 Correction Coefficient a: Fixed C
*ENG [0 to 2 / 1 / 0.001/step]
*ENG [0 to 2 / 1 / 0.001/step]
2-005-046 Correction Coefficient a: Fixed M *ENG [0 to 2 / 1 / 0.001/step]
2-005-047 Correction Coefficient a: Fixed Y *ENG [0 to 2 / 1 / 0.001/step]
2-005-048 Correction Coefficient b: Fixed K
2-005-049 Correction Coefficient b: Fixed C
*ENG [0 to 2000 / 700 / 1-V/step]
*ENG [0 to 2000 / 700 / 1-V/step]
Engine SP Tables - SP2000-1
2-005-050 Correction Coefficient b: Fixed M *ENG [0 to 2000 / 700 / 1-V/step]
2-005-051 Correction Coefficient b: Fixed Y
2-005-052 Correction Coefficient c: Fixed K
*ENG [0 to 2000 / 700 / 1-V/step]
*ENG [0 to 100 / 0 / 1-V/step]
2-005-053 Correction Coefficient c: Fixed C
2-005-054 Correction Coefficient c: Fixed M
*ENG [0 to 100 / 0 / 1-V/step]
*ENG [0 to 100 / 0 / 1-V/step]
2-005-055 Correction Coefficient c: Fixed Y *ENG [0 to 100 / 0 / 1-V/step]
2-005-056 Correction Rotation : Charge R: K *ENG [0 to 999999999/ 0 / 1mm/step]
2-005-057 Correction Rotation : Charge R: C *ENG [0 to 999999999/ 0 / 1mm/step]
2-005-058 Correction Rotation : Charge R: M *ENG [0 to 999999999/ 0 / 1mm/step]
2-005-059 Correction Rotation : Charge R: Y *ENG [0 to 999999999/ 0 / 1mm/step]
2-005-060 Correction Rotation : OPC R: K *ENG [0 to 999999999/ 0 / 1mm/step]
2-005-061 Correction Rotation : OPC R: C
2-005-062 Correction Rotation : OPC R: M
2-005-063 Correction Rotation : OPC R: Y
2-005-064 Correction Coefficient Cd
*ENG
*ENG
*ENG
*ENG
[0 to 999999999/ 0 / 1mm/step]
[0 to 999999999/ 0 / 1mm/step]
[0 to 999999999/ 0 / 1mm/step]
[-125 to 125 / 10 / 1-V/step]
2-005-065 Correction Coefficient Ce
2-005-066 Correction Coefficient Cf
2-005-067 Correction Coefficient Cg
2-005-068 Correction Coefficient Ch
2-005-069 Correction Coefficient Ci
*ENG [-125 to 125 / 13 / 1-V/step]
*ENG [-125 to 125 / 16 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 10 / 1-V/step]
2-005-070 Correction Coefficient Cj
2-005-071 Correction Coefficient Ck
2-005-072 Correction Coefficient Cl
2-005-073 Correction Coefficient Cm
2-005-074 Correction Coefficient Cn
2-005-075 Correction Coefficient Co
*ENG [-125 to 125 / 13 / 1-V/step]
*ENG [-125 to 125 / 16 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 10 / 1-V/step]
*ENG [-125 to 125 / 13 / 1-V/step]
159
160
3. Engine SP Mode Tables
2-005-076 Correction Coefficient Cp
2-005-077 Correction Coefficient Cq
2-005-078 Correction Coefficient Cr
2-005-079 Correction Coefficient Cs
2-005-080 Correction Coefficient Ct
2-005-081 Correction Coefficient Cu
2-005-082 Correction Coefficient Cv
2-005-083 Correction Coefficient Cw
2-005-084 Correction Coefficient Cx
2-005-085 Correction Coefficient Cy
2-005-086 Correction Coefficient Cz
2-005-087 Correction Coefficient CAA
2-005-088 Correction Coefficient CAB
2-005-089 Correction Coefficient Cd
2-005-090 Correction Coefficient Ce
2-005-091 Correction Coefficient Cf
2-005-092 Correction Coefficient Cg
2-005-093 Correction Coefficient Ch
2-005-094 Correction Coefficient Ci
2-005-095 Correction Coefficient Cj
2-005-096 Correction Coefficient Ck
2-005-097 Correction Coefficient Cl
2-005-098 Correction Coefficient Cm
2-005-099 Correction Coefficient Cn
2-005-100 Correction Coefficient Co
2-005-101 Correction Coefficient Cp
*ENG [-125 to 125 / 16 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 10 / 1-V/step]
*ENG [-125 to 125 / 13 / 1-V/step]
*ENG [-125 to 125 / 16 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 10 / 1-V/step]
*ENG [-125 to 125 / 13 / 1-V/step]
*ENG [-125 to 125 / 16 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
2-005-102 Correction Coefficient Cq
2-005-103 Correction Coefficient Cr
2-005-104 Correction Coefficient Cs
2-005-105 Correction Coefficient Ct
2-005-106 Correction Coefficient Cu
2-005-107 Correction Coefficient Cv
2-005-108 Correction Coefficient Cw
2-005-109 Correction Coefficient Cx
2-005-110 Correction Coefficient Cy
2-005-111 Correction Coefficient Cz
2-005-112 Correction Coefficient CAA
2-005-113 Correction Coefficient CAB
2-005-114 Correction Coefficient Md
2-005-115 Correction Coefficient Me
2-005-116 Correction Coefficient Mf
2-005-117 Correction Coefficient Mg
2-005-118 Correction Coefficient Mh
2-005-119 Correction Coefficient Mi
2-005-120 Correction Coefficient Mj
2-005-121 Correction Coefficient Mk
2-005-122 Correction Coefficient Ml
2-005-123 Correction Coefficient Mm
2-005-124 Correction Coefficient Mn
2-005-125 Correction Coefficient Mo
2-005-126 Correction Coefficient Mp
2-005-127 Correction Coefficient Mq
Engine SP Tables - SP2000-1
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
161
162
3. Engine SP Mode Tables
2-005-128 Correction Coefficient Mr
2-005-129 Correction Coefficient Ms
2-005-130 Correction Coefficient Mt
2-005-131 Correction Coefficient Mu
2-005-132 Correction Coefficient Mv
2-005-133 Correction Coefficient Mw
2-005-134 Correction Coefficient Mx
2-005-135 Correction Coefficient My
2-005-136 Correction Coefficient Mz
2-005-137 Correction Coefficient MAA
2-005-138 Correction Coefficient MAB
2-005-139 Correction Coefficient Yd
2-005-140 Correction Coefficient Ye
2-005-141 Correction Coefficient Yf
2-005-142 Correction Coefficient Yg
2-005-143 Correction Coefficient Yh
2-005-144 Correction Coefficient Yi
2-005-145 Correction Coefficient Yj
2-005-146 Correction Coefficient Yk
2-005-147 Correction Coefficient Yl
2-005-148 Correction Coefficient Ym
2-005-149 Correction Coefficient Yn
2-005-150 Correction Coefficient Yo
2-005-151 Correction Coefficient Yp
2-005-152 Correction Coefficient Yq
2-005-153 Correction Coefficient Yr
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
Engine SP Tables - SP2000-1
2-005-154 Correction Coefficient Ys
2-005-155 Correction Coefficient Yt
2-005-156 Correction Coefficient Yu
2-005-157 Correction Coefficient Yv
2-005-158 Correction Coefficient Yw
2-005-159 Correction Coefficient Yx
2-005-160 Correction Coefficient Yy
2-005-161 Correction Coefficient Yz
2-005-162 Correction Coefficient YAA
2-005-163 Correction Coefficient YAB
2-005-164 Correction Coefficient b1: K
2-005-165 Correction Coefficient b1: C
2-005-166 Correction Coefficient b1: M
2-005-167 Correction Coefficient b1: Y
2-005-168 Temperature Threshold
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-125 to 125 / 0 / 1-V/step]
*ENG [-300 to 300 / 0 / 1/step]
*ENG [-300 to 300 / 0 / 1/step]
*ENG [-300 to 300 / 0 / 1/step]
*ENG [-300 to 300 / 0 / 1/step]
*ENG [1 to 99 / 20 / 1/step]
2-005-169 Environmental Target Temperature *ENG [-100 to 700 / 200 / 0.1/step]
2-005-170 Temp PCU: K *ENG [-100 to 700 / 200 / 0.1/step]
2-005-171 Temp PCU: C
2-005-172 Temp PCU: M
2-005-173 Temp PCU: Y
*ENG [-100 to 700 / 200 / 0.1/step]
*ENG [-100 to 700 / 200 / 0.1/step]
*ENG [-100 to 700 / 200 / 0.1/step]
2-005-174 Temp Charge R: K
2-005-175 Temp Charge R: C
2-005-176 Temp Charge R: M
2-005-177 Temp Charge R: Y
2-005-178 Correction Temp Charge R: K
2-005-179 Correction Temp Charge R: C
*ENG [0 to 9999 / 0 / 1/step]
*ENG [0 to 9999 / 0 / 1/step]
*ENG [0 to 9999 / 0 / 1/step]
*ENG [0 to 9999 / 0 / 1/step]
*ENG [-99 to 99 / 0 / 1-V/step]
*ENG [-99 to 99 / 0 / 1-V/step]
163
164
3. Engine SP Mode Tables
2-005-180 Correction Temp Charge R: M
2-005-181 Correction Temp Charge R: Y
2-005-182 Correction Coefficient bb: K
2-005-183 Correction Coefficient bb: C
2-005-184 Correction Coefficient bb: M
2-005-185 Correction Coefficient bb: Y
2-005-186 Correction Coefficient dd1
2-005-187 Correction Coefficient dd1
2-005-188 Correction Coefficient dd3
2-005-189 Correction Coefficient dd4
2-005-190 JOB DotCoverage:K
2-005-191 JOB DotCoverage:C
2-005-192 JOB DotCoverage:M
2-005-193 JOB DotCoverage:Y
2-005-194 Correction Coefficient cc: K
2-005-195 Correction Coefficient cc: C
2-005-196 Correction Coefficient cc: M
2-005-197 Correction Coefficient cc: Y
2-005-198 Temp Difference
2-005-199 Correction Coefficient b2: K
2-005-200 Correction Coefficient b2: C
2-005-201 Correction Coefficient b2: M
2-005-202 Correction Coefficient b2: Y
2-005-203 Correction Coefficient ee: K
2-005-204 Correction Coefficient ee: C
2-005-205 Correction Coefficient ee: M
*ENG [-99 to 99 / 0 / 1-V/step]
*ENG [-99 to 99 / 0 / 1-V/step]
*ENG [0 to 1000 / 100 / 0.001/step]
*ENG [0 to 1000 / 100 / 0.001/step]
*ENG [0 to 1000 / 100 / 0.001/step]
*ENG [0 to 1000 / 100 / 0.001/step]
*ENG [0 to 200 / 100 / 0.01/step]
*ENG [0 to 200 / 100 / 0.01/step]
*ENG [0 to 200 / 100 / 0.01/step]
*ENG [0 to 200 / 100 / 0.01/step]
*ENG [0 to 10000 / 0 / 0.01%/step]
*ENG [0 to 10000 / 0 / 0.01%/step]
*ENG [0 to 10000 / 0 / 0.01%/step]
*ENG [0 to 10000 / 0 / 0.01%/step]
*ENG [0 to 900 / 80 / 0.01/step]
*ENG [0 to 900 / 80 / 0.01/step]
*ENG [0 to 900 / 80 / 0.01/step]
*ENG [0 to 900 / 80 / 0.01/step]
*ENG [-800 to 800 / 0 / 0.1/step]
*ENG [-99 to 99 / 0 / 1-V/step]
*ENG [-99 to 99 / 0 / 1-V/step]
*ENG [-99 to 99 / 0 / 1-V/step]
*ENG [-99 to 99 / 0 / 1-V/step]
*ENG [0 to 100 / 38 / 0.1/step]
*ENG [0 to 100 / 38 / 0.1/step]
*ENG [0 to 100 / 38 / 0.1/step]
Engine SP Tables - SP2000-1
2-005-206 Correction Coefficient ee: Y
2-005-207 Correction Coefficient b3: K
2-005-208 Correction Coefficient b3: C
2-005-209 Correction Coefficient b3: M
2-005-210 Correction Coefficient b3: Y
2-005-211 Correction Coefficient gg: K
2-005-212 Correction Coefficient gg: C
2-005-213 Correction Coefficient gg: M
2-005-214 Correction Coefficient gg: Y
2-005-215 Correction Coefficient hh1: K
2-005-216 Correction Coefficient hh1: C
2-005-217 Correction Coefficient hh1: M
2-005-218 Correction Coefficient hh1: Y
2-005-219 Correction Coefficient hh2: K
2-005-220 Correction Coefficient hh2: C
2-005-221 Correction Coefficient hh2: M
2-005-222 Correction Coefficient hh2: Y
2-005-223 Correction Coefficient hh3: K
2-005-224 Correction Coefficient hh3: C
2-005-225 Correction Coefficient hh3: M
2-005-226 Correction Coefficient hh3: Y
2-005-227 Correction Coefficient hh4: K
2-005-228 Correction Coefficient hh4: C
2-005-229 Correction Coefficient hh4: M
2-005-230 Correction Coefficient hh4: Y
2-005-231 Correction Coefficient b0: K
*ENG [0 to 100 / 38 / 0.1/step]
*ENG [-99 to 99 / 0 / 1-V/step]
*ENG [-99 to 99 / 0 / 1-V/step]
*ENG [-99 to 99 / 0 / 1-V/step]
*ENG [-99 to 99 / 0 / 1-V/step]
*ENG [0 to 900 / 130 / 0.01/step]
*ENG [0 to 900 / 130 / 0.01/step]
*ENG [0 to 900 / 130 / 0.01/step]
*ENG [0 to 900 / 130 / 0.01/step]
*ENG [0 to 900 / 100 / 0.01/step]
*ENG [0 to 900 / 100 / 0.01/step]
*ENG [0 to 900 / 100 / 0.01/step]
*ENG [0 to 900 / 100 / 0.01/step]
*ENG [0 to 900 / 100 / 0.01/step]
*ENG [0 to 900 / 100 / 0.01/step]
*ENG [0 to 900 / 100 / 0.01/step]
*ENG [0 to 900 / 100 / 0.01/step]
*ENG [0 to 900 / 100 / 0.01/step]
*ENG [0 to 900 / 100 / 0.01/step]
*ENG [0 to 900 / 100 / 0.01/step]
*ENG [0 to 900 / 100 / 0.01/step]
*ENG [0 to 900 / 100 / 0.01/step]
*ENG [0 to 900 / 100 / 0.01/step]
*ENG [0 to 900 / 100 / 0.01/step]
*ENG [0 to 900 / 100 / 0.01/step]
*ENG [0 to 2000 / 714 / 1/step]
165
166
3. Engine SP Mode Tables
2-005-232 Correction Coefficient b0: C
2-005-233 Correction Coefficient b0: M
2-005-234 Correction Coefficient b0: Y
2-005-235 Correction Coefficient c1: K
2-005-236 Correction Coefficient c1: C
2-005-237 Correction Coefficient c1: M
2-005-238 Correction Coefficient c1: Y
*ENG [0 to 2000 / 714 / 1/step]
*ENG [0 to 2000 / 714 / 1/step]
*ENG [0 to 2000 / 714 / 1/step]
*ENG [-80 to 80 / 0 / 1/step]
*ENG [-80 to 80 / 0 / 1/step]
*ENG [-80 to 80 / 0 / 1/step]
*ENG [-80 to 80 / 0 / 1/step]
2-005-239 Correction Coefficient c2: K
2-005-240 Correction Coefficient c2: C
2-005-241 Correction Coefficient c2: M
2-005-242 Correction Coefficient c2: Y
2-005-243 Rotation At Prev Correction: VdVc:
Bk
2-005-244 Rotation At Prev Correction: VdVc:
C
2-005-245 Rotation At Prev Correction: VdVc:
M
2-005-246 Rotation At Prev Correction: VdVc:
Y
*ENG [-20 to 20 / 0 / 1/step]
*ENG [-20 to 20 / 0 / 1/step]
*ENG [-20 to 20 / 0 / 1/step]
*ENG [-20 to 20 / 0 / 1/step]
*ENG [0 to 999999999 / 0 / 1mm/step]
*ENG [0 to 999999999 / 0 / 1mm/step]
*ENG [0 to 999999999 / 0 / 1mm/step]
*ENG [0 to 999999999 / 0 / 1mm/step]
2-005-247 Correction Coefficient b2: Fixed K *ENG [-99 to 99 / 37 / 1-V/step]
2-005-248 Correction Coefficient b2: Fixed C *ENG [-99 to 99 / 37 / 1-V/step]
2-005-249 Correction Coefficient b2: Fixed M *ENG [-99 to 99 / 37 / 1-V/step]
2-005-250 Correction Coefficient b2: Fixed Y *ENG [-99 to 99 / 37 / 1-V/step]
2006 [Charge AC Voltage: Fixed]
2-006-001 Standard Speed: K
2-006-002 Standard Speed: C
2-006-003 Standard Speed: M
2-006-004 Standard Speed: Y
2-006-005 Middle Speed: K
2-006-006 Middle Speed: C
2-006-007 Middle Speed: M
2-006-008 Middle Speed: Y
2-006-009 Low Speed: K
2-006-010 Low Speed: C
2-006-011 Low Speed: M
2-006-012 Low Speed: Y
2007 [Charge AC Current: LL]
2-007-001 Environmental Target: Bk
2-007-002 Environmental Target: C
2-007-003 Environmental Target: M
2-007-004 Environmental Target: Y
2008 [Charge AC Current: ML]
2-008-001 Environmental Target: Bk
2-008-002 Environmental Target: C
2-008-003 Environmental Target: M
2-008-004 Environmental Target: Y
2009 [Charge AC Current: MM]
Engine SP Tables - SP2000-1
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG [0 to 3 / 2.2 / 0.01kV/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG [0 to 3 / 0.81 / 0.01mA/step]
*ENG
*ENG
*ENG
*ENG [0 to 3 / 0.81 / 0.01mA/step]
*ENG
*ENG
*ENG
167
168
3. Engine SP Mode Tables
2-009-001 Environmental Target: Bk
2-009-002 Environmental Target: C
2-009-003 Environmental Target: M
2-009-004 Environmental Target: Y
2010 [Charge AC Current: MH]
2-010-001 Environmental Target: Bk
2-010-002 Environmental Target: C
2-010-003 Environmental Target: M
2-010-004 Environmental Target: Y
*ENG [0 to 3 / 0.81 / 0.01mA/step]
*ENG
*ENG
*ENG
*ENG [0 to 3 / 0.83 / 0.01mA/step]
*ENG
*ENG
*ENG
2011 [Charge AC Current: HH]
2-011-001 Environmental Target: Bk
2-011-002 Environmental Target: C
2-011-003 Environmental Target: M
2-011-004 Environmental Target: Y
2012 [Charge Output Control]
2-012-001 AC Voltage
*ENG [0 to 3 / 0.86 / 0.01mA/step]
*ENG
*ENG
*ENG
*ENG [0 or 1 / 0 / 1/step]
0: Set to environment correction value used when FB .
1: Electrify AC voltage of SP: Set to fixed setting value.
2013 [Environmental Correction: PCU]
2-013-001 Current Environmental FC : Display *ENG [0 to 0 / 0 / 1/step]
2-013-002 Forced Setting
2-013-003 Absolute Humidity: Threshold 1
2-013-004 Absolute Humidity: Threshold 2
*ENG [0 to 5 / 0 / 1/step]
*ENG [0 to 100 / 3 / 0.01g/m
3
/step]
*ENG [0 to 100 / 8 / 0.01g/m
3
/step]
Engine SP Tables - SP2000-1
2-013-005 Absolute Humidity: Threshold 3
2-013-006 Absolute Humidity: Threshold 4
2-013-007 Temp FC: Display
2-013-008 Relative Humidity FC : Display
2-013-009 Absolute Humidity FC : Display
2-013-010 Environmental Bk: Display
2-013-011 Temp Bk.: Display
2-013-012 Relative Humidity Bk : Display
2-013-013 Absolute Humidity Bk : Display
2014 [Charge AC Control: Setting]
2-014-001 Exec Interval: Power ON
2-014-002 Exec Interval: Print
2-014-003 Page Interval
2-014-004 Temperature
2-014-005 Relative Humidity
2-014-006 Absolute Humidity
2-014-007 Temp Threshold M
2-014-008 RH Threshold M
2-014-009 AH Threshold M
2-014-010 Temp Threshold S
2-014-011 RH Threshold S
2-014-012 AH Threshold S
2-014-013 Non-use Time
2-014-014 AC Current Error Detection
2015 [Charge AC Adj: Result]
*ENG [0 to 100 / 15 / 0.01g/m
3
/step]
*ENG [0 to 100 / 22 / 0.01g/m
3
/step]
*ENG [0 to 100 / 0 / 1deg/step]
*ENG [0 to 100 / 0 / 1%RH/step]
*ENG [0 to 100 / 0 / 0.01g/m
3
/step]
*ENG [0 to 0 / 0 / 1/step]
*ENG [0 to 100 / 0 / 1deg/step]
*ENG [0 to 100 / 0 / 1%RH/step]
*ENG [0 to 100 / 0 / 0.01g/m
3
/step]
*ENG [0 to 2000 / 500 / 1page/step]
*ENG [0 to 2000 / 0 / 1page/step]
*ENG [0 to 500 / 10 / 1page/step]
*ENG [0 to 99 / 35 / 1deg/step]
*ENG [0 to 99 / 50 / 1%RH/step]
*ENG [0 to 99 / 12 / 1g/m3/step]
*ENG [0 to 99 / 10 / 1deg/step]
*ENG [0 to 99 / 50 / 1%RH/step]
*ENG [0 to 99 / 6 / 1g/m
3
/step]
*ENG [0 to 20 / 1 / 0.1deg/step]
*ENG [0 to 50 / 5 / 1%RH/step]
*ENG [0 to 20 / 1 / 0.1g/m
3
/step]
*ENG [0 to 1440 / 360 / 10min/step]
*ENG [0 or 1 / 0 / 1/step]
169
3. Engine SP Mode Tables
170
2-015-001 Bk
2-015-002 C
2-015-003 M
2-015-004 Y
2020 [Background Pot Corr. Set]
2-020-001 Temp. Condition
2-020-002 Absolute Humidity
2-020-003 Print Page Counter After Corr.
2-020-004 Print Pages Threshold After Corr.
2-020-005 Temp. Thresh
2-020-011 Coeff. a: K
2-020-012 Coeff. a: C
2-020-013 Coeff. a: M
2-020-014 Coeff. a: Y
2-020-015 Coeff. b: K
2-020-016 Coeff. b: C
2-020-017 Coeff. b: M
2-020-018 Coeff. b: Y
2021 [Background Pot Corr.]
2-021-002 Display: C
2-021-003 Display: M
2-021-004 Display: Y
2-021-005 Setting 1: K
2-021-006 Setting 1: C
2-021-007 Setting 1: M
*ENG [0 to 9 / 0 / 1/step]
*ENG [0 to 9 / 0 / 1/step]
*ENG [0 to 9 / 0 / 1/step]
*ENG [0 to 9 / 0 / 1/step]
*ENG [0 to 19 / 15 / 1deg/step]
*ENG [0 to 99 / 6 / 1g/m
3
/step]
*ENG [0 to 999 / 0 / 1page/step]
*ENG [0 to 999 / 10 / 1page/step]
*ENG [20 to 99 / 20 / 1deg/step]
*ENG [0 to 1 / 0.06 / 0.01/step]
*ENG [0 to 1 / 0.06 / 0.01/step]
*ENG [0 to 1 / 0.06 / 0.01/step]
*ENG [0 to 1 / 0.06 / 0.01/step]
*ENG [0 to 9 / 0.5 / 0.01/step]
*ENG [0 to 9 / 0.5 / 0.01/step]
*ENG [0 to 9 / 0.5 / 0.01/step]
*ENG [0 to 9 / 0.5 / 0.01/step]
*ENG [0 to 90 / 0 / 1-V/step]
*ENG [0 to 90 / 0 / 1-V/step]
*ENG [0 to 90 / 0 / 1-V/step]
*ENG [0 to 90 / 0 / 10-V/step]
*ENG [0 to 90 / 0 / 10-V/step]
*ENG [0 to 90 / 0 / 10-V/step]
2-021-008 Setting 1: Y
2-021-009 Setting 2: K
2-021-010 Setting 2: C
2-021-011 Setting 2: M
2-021-012 Setting 2: Y
2-021-013 Setting 3: K
2-021-014 Setting 3: C
2-021-015 Setting 3: M
2-021-016 Setting 3: Y
2-021-017 Setting 4: K
2-021-018 Setting 4: C
2-021-019 Setting 4: M
2-021-020 Setting 4: Y
2-021-021 Setting 5: K
2-021-022 Setting 5: C
2-021-023 Setting 5: M
2-021-024 Setting 5: Y
2-021-025 Setting 6: K
2-021-026 Setting 6: C
2-021-027 Setting 6: M
2-021-028 Setting 6: Y
2-021-029 Display: Energized: K
2-021-030 Display: Energized: C
2-021-031 Display: Energized: M
2-021-032 Display: Energized: Y
2-021-033 Display: Total Rotation: K
Engine SP Tables - SP2000-1
*ENG [0 to 90 / 0 / 10-V/step]
*ENG [0 to 90 / 0 / 10-V/step]
*ENG [0 to 90 / 0 / 10-V/step]
*ENG [0 to 90 / 0 / 10-V/step]
*ENG [0 to 90 / 0 / 10-V/step]
*ENG [0 to 90 / 0 / 5-V/step]
*ENG [0 to 90 / 0 / 5-V/step]
*ENG [0 to 90 / 0 / 5-V/step]
*ENG [0 to 90 / 0 / 5-V/step]
*ENG [0 to 90 / 0 / 5-V/step]
*ENG [0 to 90 / 0 / 5-V/step]
*ENG [0 to 90 / 0 / 5-V/step]
*ENG [0 to 90 / 0 / 5-V/step]
*ENG [0 to 90 / 0 / 1-V/step]
*ENG [0 to 90 / 0 / 1-V/step]
*ENG [0 to 90 / 0 / 1-V/step]
*ENG [0 to 90 / 0 / 1-V/step]
*ENG [-90 to 90 / 2 / 1-V/step]
*ENG [-90 to 90 / 2 / 1-V/step]
*ENG [-90 to 90 / 2 / 1-V/step]
*ENG [-90 to 90 / 2 / 1-V/step]
*ENG [0 to 90 / 0 / 1-V/step]
*ENG [0 to 90 / 0 / 1-V/step]
*ENG [0 to 90 / 0 / 1-V/step]
*ENG [0 to 90 / 0 / 1-V/step]
*ENG [0 to 90 / 0 / 1-V/step]
171
172
3. Engine SP Mode Tables
2-021-034 Display: Total Rotation: C
2-021-035 Display: Total Rotation: M
2-021-036 Display: Total Rotation: Y
2-021-037 Split Number n: K
2-021-038 Split Number n: C
2-021-039 Split Number n: M
2-021-040 Split Number n: Y
2-021-041 Display:Energized for Target
Value:K
2-021-042 Display:Energized for Target
Value:C
2-021-043 Display:Energized for Target
Value:M
2-021-044 Display:Energized for Target
Value:Y
2-021-045 Setting 7: K
2-021-046 Setting 7: C
2-021-047 Setting 7: M
2-021-048 Setting 7: Y
2022 [Charge R Running Par]
2-022-001 Display:K
2-022-002 Display:C
2-022-003 Display:M
2-022-004 Display:Y
2-022-005 PCU Rotation Time After
Correction: K
*ENG [0 to 90 / 0 / 1-V/step]
*ENG [0 to 90 / 0 / 1-V/step]
*ENG [0 to 90 / 0 / 1-V/step]
*ENG [1 to 99 / 12 / 1/step]
*ENG [1 to 99 / 12 / 1/step]
*ENG [1 to 99 / 12 / 1/step]
*ENG [1 to 99 / 12 / 1/step]
*ENG [0 to 90 / 0 / 1-V/step]
*ENG [0 to 90 / 0 / 1-V/step]
*ENG [0 to 90 / 0 / 1-V/step]
*ENG [0 to 90 / 0 / 1-V/step]
*ENG [0 to 50 / 24 / 1-V/step]
*ENG [0 to 50 / 24 / 1-V/step]
*ENG [0 to 50 / 24 / 1-V/step]
*ENG [0 to 50 / 24 / 1-V/step]
*ENG [0 to 999999 / 0 / 1/step]
*ENG [0 to 999999 / 0 / 1/step]
*ENG [0 to 999999 / 0 / 1/step]
*ENG [0 to 999999 / 0 / 1/step]
*ENG [0 to 9999999 / 0 / 1/step]
2-022-006 PCU Rotation Time After
Correction: C
2-022-007 PCU Rotation Time After
Correction: M
2-022-008 PCU Rotation Time After
Correction: Y
2-022-009 Threshold1:K
2-022-010 Threshold1:C
2-022-011 Threshold1:M
2-022-012 Threshold1:Y
2-022-013 Threshold2:K
2-022-014 Threshold2:C
2-022-015 Threshold2:M
2-022-016 Threshold2:Y
2-022-017 Threshold3:K
2-022-018 Threshold3:C
2-022-019 Threshold3:M
2-022-020 Threshold3:Y
2-022-021 Threshold4:K
2-022-022 Threshold4:C
2-022-023 Threshold4:M
2-022-024 Threshold4:Y
2-022-025 Prev Correction Calculation
Bk:Year
2-022-026 Prev Correction Calculation
Bk:Month
2-022-027 Prev Correction Calculation
Bk:Day
Engine SP Tables - SP2000-1
*ENG [0 to 9999999 / 0 / 1/step]
*ENG [0 to 9999999 / 0 / 1/step]
*ENG [0 to 9999999 / 0 / 1/step]
*ENG [0 to 4000 / 30 / 1/step]
*ENG [0 to 4000 / 30 / 1/step]
*ENG [0 to 4000 / 30 / 1/step]
*ENG [0 to 4000 / 30 / 1/step]
*ENG [0 to 4000 / 70 / 1/step]
*ENG [0 to 4000 / 70 / 1/step]
*ENG [0 to 4000 / 70 / 1/step]
*ENG [0 to 4000 / 70 / 1/step]
*ENG [0 to 4000 / 150 / 1/step]
*ENG [0 to 4000 / 150 / 1/step]
*ENG [0 to 4000 / 150 / 1/step]
*ENG [0 to 4000 / 150 / 1/step]
*ENG [0 to 4000 / 250 / 1/step]
*ENG [0 to 4000 / 250 / 1/step]
*ENG [0 to 4000 / 250 / 1/step]
*ENG [0 to 4000 / 250 / 1/step]
*ENG [0 to 99 / 0 / 1year/step]
*ENG [1 to 12 / 1 / 1month] /step]
*ENG [1 to 31 / 1 / 1day/step]
173
174
3. Engine SP Mode Tables
2-022-028 Prev Correction Calculation
Bk:Hour
2-022-029 Prev Correction Calculation
Bk:Minute
2-022-030 Rotation At Prev Correction: PCU:
Bk
2-022-031 Rotation At Prev Correction: PCU:
C
2-022-032 Rotation At Prev Correction: PCU:
M
2-022-033
Rotation At Prev Correction: PCU:
Y
*ENG [0 to 23 / 0 / 1hour/step]
*ENG [0 to 59 / 0 / 1minute/step]
*ENG [0 to 999999999 / 0 / 1mm/step]
*ENG [0 to 999999999 / 0 / 1mm/step]
*ENG [0 to 999999999 / 0 / 1mm/step]
*ENG
[0 to 999999999 / 0 / 1mm/step]
2101 [Registration Correction]
2-101-001 Color Main Dot: Bk
2-101-002 Color Main Dot: Ma
2-101-003 Color Main Dot: Cy
2-101-004 Color Main Dot: Ye
2-101-005 Color Sub Line: Bk
2-101-006 Color Sub Line: Ma
2-101-007 Color Sub Line: Cy
2-101-008 Color Sub Line: Ye
*ENG [-512 to 511 / 0 / 1dot/step]
*ENG [-512 to 511 / 0 / 1dot/step]
*ENG [-512 to 511 / 0 / 1dot/step]
*ENG [-512 to 511 / 0 / 1dot/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
2102 [Magnification Adjustment]
2-102-001 Main Mag.: Standard Speed: Bk
2-102-002 Main Mag.: Middle Speed: Bk
*ENG [-2 to 2 / 0 / 0.001%/step]
*ENG [-2 to 2 / 0 / 0.001%/step]
2-102-003 Main Mag.: Low Speed: Bk *ENG [-2 to 2 / 0 / 0.001%/step]
2-102-004 Main Mag.: Standard Speed: Ma *ENG [-2 to 2 / 0 / 0.001%/step]
2-102-005 Main Mag.: Middle Speed: Ma *ENG [-2 to 2 / 0 / 0.001%/step]
Engine SP Tables - SP2000-1
2-102-006 Main Mag.: Low Speed: Ma *ENG [-2 to 2 / 0 / 0.001%/step]
2-102-007 Main Mag.: Standard Speed: Cy *ENG [-2 to 2 / 0 / 0.001%/step]
2-102-008 Main Mag.: Middle Speed: Cy *ENG [-2 to 2 / 0 / 0.001%/step]
2-102-009 Main Mag.: Low Speed: Cy
2-102-010 Main Mag.: Standard Speed: Ye
*ENG [-2 to 2 / 0 / 0.001%/step]
*ENG [-2 to 2 / 0 / 0.001%/step]
2-102-011 Main Mag.: Middle Speed: Ye
2-102-012 Main Mag.: Low Speed: Ye
2-102-028 Color Main Mag.: High Speed:
Ma
*ENG [-2 to 2 / 0 / 0.001%/step]
*ENG [-2 to 2 / 0 / 0.001%/step]
*ENG [-2 to 2 / 0 / 0.001%/step]
2-102-031 Color Main Mag.: High Speed: Cy *ENG [-2 to 2 / 0 / 0.001%/step]
2-102-034 Color Main Mag.: High Speed: Ye *ENG [-2 to 2 / 0 / 0.001%/step]
2102 [Main Scan Beam Pitch Adj.]
2-102-037 Bk: 1st-2nd
2-102-038 Bk: 1st-3rd
2-102-039 Bk: 1st-4th
*ENG [0 to 100 / 9.61 / 0.01dot/step]
*ENG [0 to 100 / 19.22 / 0.01dot/step]
2-102-040 Ma: 1st-2nd
2-102-041 Ma: 1st-3rd
*ENG [0 to 100 / 28.83 / 0.01dot/step]
*ENG [0 to 100 / 9.61 / 0.01dot/step]
*ENG [0 to 100 / 19.22 / 0.01dot/step]
2-102-042 Ma: 1st-4th
2-102-043 Cy: 1st-2nd
2-102-044 Cy: 1st-3rd
2-102-045 Cy: 1st-4th
2-102-046 Ye: 1st-2nd
2-102-047 Ye: 1st-3rd
2-102-048 Ye: 1st-4th
*ENG [0 to 100 / 28.83 / 0.01dot/step]
*ENG [0 to 100 / 9.61 / 0.01dot/step]
*ENG [0 to 100 / 19.22 / 0.01dot/step]
*ENG [0 to 100 / 28.83 / 0.01dot/step]
*ENG [0 to 100 / 9.61 / 0.01dot/step]
*ENG [0 to 100 / 19.22 / 0.01dot/step]
*ENG [0 to 100 / 28.83 / 0.01dot/step]
2103 [Erase Margin Adjustment]
175
3. Engine SP Mode Tables
176
2-103-001 Lead Edge Width
2-103-002 Trail. Edge Width
2-103-003 Left
2-103-004 Right
2-103-006 Duplex Trail. L Size
2-103-007 Duplex Trail. M Size
2-103-008 Duplex Trail. S Size
2-103-009 Duplex Left Edge
2-103-010 Duplex Right Edge
2-103-011 Duplex Trail. L Size:Thick
2-103-012 Duplex Trail. M Size:Thick
2-103-013 Duplex Trail. S Size:Thick
2-103-014 Duplex Left Edge:Thick
2-103-015 Duplex Right Edge:Thick
2-103-016 Duplex Trail. L Size:Thin
2-103-017 Duplex Trail. M Size:Thin
2-103-018 Duplex Trail. S Size:Thin
2-103-019 Lead Edge Width:Thin
2-103-020 Trail. Edge Width:Thin
2106 [Polygon Rotation Time]
2-106-001 Warming-Up
2-106-002 Job End
2107 [Image Parameter]
2-107-001 Image Gamma Flag
2-107-002 Shading Correction Flag
ENG [0 to 9.9 / 4.2 / 0.1mm/step]
ENG [0 to 9.9 / 4.2 / 0.1mm/step]
ENG [0 to 9.9 / 2 / 0.1mm/step]
ENG [0 to 9.9 / 2 / 0.1mm/step]
ENG [-4 to 4 / 0.8 / 0.1mm/step]
ENG [-4 to 4 / 0.8 / 0.1mm/step]
ENG [-4 to 4 / 0.6 / 0.1mm/step]
ENG [0 to 1.5 / 0.3 / 0.1mm/step]
ENG [0 to 1.5 / 0.3 / 0.1mm/step]
ENG [-4 to 4 / 0.8 / 0.1mm/step]
ENG [-4 to 4 / 0.8 / 0.1mm/step]
ENG [-4 to 4 / 0.6 / 0.1mm/step]
ENG [0 to 1.5 / 0.3 / 0.1mm/step]
ENG [0 to 1.5 / 0.3 / 0.1mm/step]
ENG [-4 to 4 / 0.8 / 0.1mm/step]
ENG [-4 to 4 / 0.8 / 0.1mm/step]
ENG [-4 to 4 / 0.6 / 0.1mm/step]
ENG [0 to 9.9 / 4.2 / 0.1mm/step]
ENG [0 to 9.9 / 4.2 / 0.1mm/step]
*ENG [0 to 60 / 10 / 1sec/step]
*ENG [0 to 60 / 0.1 / 0.1sec/step]
ENG [0 or 1 / 1 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
Engine SP Tables - SP2000-1
2109 [Test Pattern]
2-109-003 Pattern Selection
0 None
1 Vertical Line (1dot)
2 Vertical Line (2dot)
3 Horizontal Line (1dot)
4 Horizontal Line (2dot)
5 Grid Vertical Line
6 Grid Horizontal Line
7 Grid Pattern Small
8 Grid Pattern Large
9 Argyle Pattern Small
10 Argyle Pattern Large
11 Independent Pattern (1dot)
2-109-005 Color Selection
2-109-006 Density: Bk
2-109-007 Density: Ma
2-109-008 Density: Cy
2-109-009 Density: Ye
ENG [0 to 23 / 0 / 1/step]
12 Independent Pattern (2dot)
13 Independent Pattern (4dot)
14 Trimming Area
15 Hound's Tooth Check (Vertical)
16 Hound's Tooth Check (Horizontal)
17 Band (Horizontal)
18 Band (Vertical)
19 Checker Flag Pattern
20 Grayscale (Vertical Margin)
21 Grayscale (Horizontal Margin)
22 Wormy Pattarn
23 Full Dot Pattern
ENG [1 to 4 / 1 / 1/step]
1: All Color
2: Ma
3: Ye
4: Cy
ENG [0 to 15 / 15 / 1/step]
ENG [0 to 15 / 15 / 1/step]
ENG [0 to 15 / 15 / 1/step]
ENG [0 to 15 / 15 / 1/step]
2110 [LD Driver]
2-110-001 Error Bk ENG [0x0000 to 0xFFFF / 0x0000 / 1/ step]
177
178
3. Engine SP Mode Tables
2-110-002 Error Ma
2-110-003 Error Cy
2-110-004 Error Ye
2-110-005 Writing Unit Adj. Transfer
2111 [Forced Line Position Adj.]
2-111-001 Mode a
2-111-002 Mode b
2-111-003 Mode c
2-111-004 Mode d
2112 [TM/ID Sensor Check]
2-112-001 Execute
2112 [TM/ID Sensor Test]
2-112-010 General:FCR
2-112-020 Threshold Setting
2117 [Skew Adjustment]
2-117-001 Pulse: M
2-117-002 Pulse: C
2-117-003 Pulse: Y
2118 [Skew Adjustment]
2-118-001 Execute: M
2-118-002 Execute: C
2-118-003 Execute: Y
ENG [0x0000 to 0xFFFF / 0x0000 / 1/ step]
ENG [0x0000 to 0xFFFF / 0x0000 / 1/ step]
ENG [0x0000 to 0xFFFF / 0x0000 / 1/ step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
*ENG [0 to 999 / 0 / 1/step]
*ENG [0 to 3.5 / 1.9 / 0.01-V/step]
*ENG [-75 to 75 / 0 / 1pulse/step]
*ENG [-75 to 75 / 0 / 1pulse/step]
*ENG [-99 to 99 / 0 / 1pulse/step]
ENG [0 or 1 / - / 1/step]
ENG [0 or 1 / - / 1/step]
ENG [0 or 1 / - / 1/step]
Engine SP Tables - SP2000-1
2119 [Skew Adjustment Display]
2-119-001 M
2-119-002 C
2-119-003 Y
*ENG [-75 to 75 / 0 / 1pulse/step]
*ENG [-75 to 75 / 0 / 1pulse/step]
*ENG [-99 to 99 / 0 / 1pulse/step]
2120 [Skew Adj Changing Line Speed]
2-120-001 On/Off *ENG [0 or 1 / 0 / 1/step]
2121 [Skew Adjust Coefficient]
2-121-001 Coefficient *ENG [0 to 2 / 0 / 1/step]
2140 [TM/ID Sensor Check Result]
2-140-005 PWM: Front
2-140-006 PWM: Center
2-140-007 PWM: Rear
2141 [TM/ID Sensor Check Result]
2-141-005 Average: Front
2-141-006 Average: Center
2-141-007 Average: Rear
2142 [TM/ID Sensor Check Result]
2-142-005 Maximum: Front
2-142-006 Maximum: Center
2-142-007 Maximum: Rear
2143 [TM/ID Sensor Check Result]
2-143-005 Minimum: Front
ENG [0 to 1023 / 0 / 1/step]
*ENG [0 to 1023 / 0 / 1/step]
*ENG [0 to 1023 / 0 / 1/step]
*ENG [0 to 5.5 / 0 / 0.01-V/step]
*ENG [0 to 5.5 / 0 / 0.01-V/step]
*ENG [0 to 5.5 / 0 / 0.01-V/step]
*ENG [0 to 5.5 / 0 / 0.01-V/step]
*ENG [0 to 5.5 / 0 / 0.01-V/step]
*ENG [0 to 5.5 / 0 / 0.01-V/step]
*ENG [0 to 5.5 / 0 / 0.01-V/step]
179
180
3. Engine SP Mode Tables
2-143-006 Minimum: Center
2-143-007 Minimum: Rear
2144 [TM/ID Sensor Check Result]
2-144-005 Maximum 2: Front
2-144-006 Maximum 2: Center
2-144-007 Maximum 2: Rear
2150 [Area Mag. Correction]
2-150-027 Area 0: Bk
2-150-028 Area 1: Bk
2-150-029 Area 2: Bk
2-150-030 Area 3: Bk
2-150-031 Area 4: Bk
2-150-032 Area 5: Bk
2-150-033 Area 6: Bk
2-150-034 Area 7: Bk
*ENG [0 to 5.5 / 0 / 0.01-V/step]
*ENG [0 to 5.5 / 0 / 0.01-V/step]
*ENG [0 to 5.5 / 0 / 0.01-V/step]
*ENG [0 to 5.5 / 0 / 0.01-V/step]
*ENG [0 to 5.5 / 0 / 0.01-V/step]
2145 [TM/ID Sensor Check Result]
2-145-005 Minimum 2: Front
2-145-006 Minimum 2: Center
2-145-007 Minimum 2: Rear
*ENG [0 to 5.5 / 0 / 0.01-V/step]
*ENG [0 to 5.5 / 0 / 0.01-V/step]
*ENG [0 to 5.5 / 0 / 0.01-V/step]
2146 [TM-Sensor Test]
2-146-005 Number of Edge Detection:Front *ENG [0 to 16 / 0 / 1/step]
2-146-006 Number of Edge Detection:Center *ENG [0 to 16 / 0 / 1/step]
2-146-007 Number of Edge Detection:Rear *ENG [0 to 16 / 0 / 1/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
2-150-035 Area 8: Bk
2-150-036 Area 9: Bk
2-150-037 Area 10: Bk
2-150-038 Area 11: Bk
2-150-039 Area 12: Bk
2-150-079 Area 0: Ma
2-150-080 Area 1: Ma
2-150-081 Area 2: Ma
2-150-082 Area 3: Ma
2-150-083 Area 4: Ma
2-150-084 Area 5: Ma
2-150-085 Area 6: Ma
2-150-086 Area 7: Ma
2-150-087 Area 8: Ma
2-150-088 Area 9: Ma
2-150-089 Area 10: Ma
2-150-090 Area 11: Ma
2-150-091 Area 12: Ma
2-150-131 Area 0: Cy
2-150-132 Area 1: Cy
2-150-133 Area 2: Cy
2-150-134 Area 3: Cy
2-150-135 Area 4: Cy
2-150-136 Area 5: Cy
2-150-137 Area 6: Cy
2-150-138 Area 7: Cy
Engine SP Tables - SP2000-1
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
181
182
3. Engine SP Mode Tables
2-150-139 Area 8: Cy
2-150-140 Area 9: Cy
2-150-141 Area 10: Cy
2-150-142 Area 11: Cy
2-150-143 Area 12: Cy
2-150-183 Area 0: Ye
2-150-184 Area 1: Ye
2-150-185 Area 2: Ye
2-150-186 Area 3: Ye
2-150-187 Area 4: Ye
2-150-188 Area 5: Ye
2-150-189 Area 6: Ye
2-150-190 Area 7: Ye
2-150-191 Area 8: Ye
2-150-192 Area 9: Ye
2-150-193 Area 10: Ye
2-150-194 Area 11: Ye
2-150-195 Area 12: Ye
2152 [Shad. Correct Setting]
2-152-001 Standard Speed: Bk
2-152-002 Standard Speed: Ma
2-152-003 Standard Speed: Cy
2-152-004 Standard Speed: Ye
2-152-005 Middle Speed: Bk
2-152-006 Middle Speed: Ma
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [-16 to 16 / 0 / 0.01dot/step]
*ENG [50 to 120 / 100 / 0.1%/step]
*ENG [50 to 120 / 100 / 0.1%/step]
*ENG [50 to 120 / 100 / 0.1%/step]
*ENG [50 to 120 / 100 / 0.1%/step]
*ENG [50 to 120 / 100 / 0.1%/step]
*ENG [50 to 120 / 100 / 0.1%/step]
2-152-007 Middle Speed: Cy
2-152-008 Middle Speed: Ye
2-152-009 Low Speed: Bk
2-152-010 Low Speed: Ma
2-152-011 Low Speed: Cy
2-152-012 Low Speed: Ye
2154 [Shad. Correct Setting]
2-154-002 Front End Area: Bk: LD1
2-154-003 Front End Area: Bk: LD2
2-154-004 Front End Area: Bk: LD3
2-154-005 Front End Area: Bk: LD4
2-154-007 Front End Area: Ma: LD1
2-154-008 Front End Area: Ma: LD2
2-154-009 Front End Area: Ma: LD3
2-154-010 Front End Area: Ma: LD4
2-154-012 Front End Area: Cy: LD1
2-154-013 Front End Area: Cy: LD2
2-154-014 Front End Area: Cy: LD3
2-154-015 Front End Area: Cy: LD4
2-154-017 Front End Area: Ye: LD1
2-154-018 Front End Area: Ye: LD2
2-154-019 Front End Area: Ye: LD3
2-154-020 Front End Area: Ye: LD4
2160 [Vertical Line Width]
2-160-001 600dpi:Bk
Engine SP Tables - SP2000-1
*ENG [50 to 120 / 100 / 0.1%/step]
*ENG [50 to 120 / 100 / 0.1%/step]
*ENG [50 to 120 / 100 / 0.1%/step]
*ENG [50 to 120 / 100 / 0.1%/step]
*ENG [50 to 120 / 100 / 0.1%/step]
*ENG [50 to 120 / 100 / 0.1%/step]
*ENG [50 to 150 / 100 / 0.1%/step]
*ENG [50 to 150 / 100 / 0.1%/step]
*ENG [50 to 150 / 100 / 0.1%/step]
*ENG [50 to 150 / 100 / 0.1%/step]
*ENG [50 to 150 / 100 / 0.1%/step]
*ENG [50 to 150 / 100 / 0.1%/step]
*ENG [50 to 150 / 100 / 0.1%/step]
*ENG [50 to 150 / 100 / 0.1%/step]
*ENG [50 to 150 / 100 / 0.1%/step]
*ENG [50 to 150 / 100 / 0.1%/step]
*ENG [50 to 150 / 100 / 0.1%/step]
*ENG [50 to 150 / 100 / 0.1%/step]
*ENG [50 to 150 / 100 / 0.1%/step]
*ENG [50 to 150 / 100 / 0.1%/step]
*ENG [50 to 150 / 100 / 0.1%/step]
*ENG [50 to 150 / 100 / 0.1%/step]
*ENG [10 to 15 / 15 / 1/step]
183
184
3. Engine SP Mode Tables
2-160-002 600dpi:Ma
2-160-003 600dpi:Cy
2-160-004 600dpi:Ye
2-160-005 1200dpi:Bk
2-160-006 1200dpi:Ma
2-160-007 1200dpi:Cy
2-160-008 1200dpi:Ye
2-160-009 600dpi:Indet.:Bk
2-160-010 1200dpi:Indet.:Bk
2180 [Line Pos. Adj. Clear]
2-180-001 Color Regist.
2-180-002 Main Scan Length Detection
2-180-003 MUSIC Result
2-180-004 Area Magnification Correction
2181 [Line Position Adj. Result]
2-181-003 Skew: M
*ENG [10 to 15 / 15 / 1/step]
*ENG [10 to 15 / 15 / 1/step]
*ENG [10 to 15 / 15 / 1/step]
*ENG [10 to 15 / 15 / 1/step]
*ENG [10 to 15 / 15 / 1/step]
*ENG [10 to 15 / 15 / 1/step]
*ENG [10 to 15 / 15 / 1/step]
*ENG [10 to 15 / 14 / 1/step]
*ENG [10 to 15 / 15 / 1/step]
ENG
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
2-181-011 M. Cor.: Dot: M
2-181-012 M. Cor.: Subdot: M
2-181-013 S. Cor.: 1200 Line: Middle: M
2-181-014 S. Cor.: 1200 Sub: Middle: M
2-181-015 M. Left Mag.: Subdot: M
2-181-016 M. Right Mag.: Subdot: M
2-181-017 S. Cor.: 1200 Line: Standard: M
2-181-018 S. Cor.: 1200 Sub: Standard: M
*ENG [-5000 to 5000 / 0 / 0.001um/ step]
*ENG [-512 to 511 / 0 / 1dot/step]
*ENG [-1 to 1 / 0 / 0.01dot/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-2 to 2 / 0 / 0.001line/step]
*ENG [-32 to 32 / 0 / 0.01dot/step]
*ENG [-32 to 32 / 0 / 0.01dot/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-2 to 2 / 0 / 0.001line/step]
Engine SP Tables - SP2000-1
2-181-019 S. Cor.: 1200 Line: Low: M
2-181-020 S. Cor.: 1200 Sub: Low: M
2-181-021 Skew: C
2-181-029 M. Cor.: Dot: C
2-181-030 M. Cor.: Subdot: C
2-181-031 S. Cor.: 1200 Line: Middle: C
2-181-032 S. Cor.: 1200 Sub: Middle: C
2-181-033 C. Left Mag.: Subdot: M
2-181-034 C. Right Mag.: Subdot: M
2-181-035 S. Cor.: 1200 Line: Standard: C
2-181-036 S. Cor.: 1200 Sub: Standard: C
2-181-037 S. Cor.: 1200 Line: Low: C
2-181-038 S. Cor.: 1200 Sub: Low: C
2-181-039 Skew: Y
2-181-047 M. Cor.: Dot: Y
2-181-048 M. Cor.: Subdot: Y
2-181-049 S. Cor.: 1200 Line: Middle: Y
2-181-050 S. Cor.: 1200 Sub: Middle: Y
2-181-051 Y. Left Mag.: Subdot: M
2-181-052 Y. Right Mag.: Subdot: M
2-181-053 S. Cor.: 1200 Line: Standard: Y
2-181-054 S. Cor.: 1200 Sub: Standard: Y
2-181-055 S. Cor.: 1200 Line: Low: Y
2-181-056 S. Cor.: 1200 Sub: Low: Y
2-181-057 S. Cor.: 600 Sub
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-2 to 2 / 0 / 0.001line/step]
*ENG [-5000 to 5000 / 0 / 0.001 / um]
*ENG [-512 to 511 / 0 / 1dot/step]
*ENG [-1 to 1 / 0 / 0.01dot/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-2 to 2 / 0 / 0.001line/step]
*ENG [-32 to 32 / 0 / 0.01dot/step]
*ENG [-32 to 32 / 0 / 0.01dot/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-2 to 2 / 0 / 0.001line/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-2 to 2 / 0 / 0.001line/step]
*ENG [-5000 to 5000 / 0 / 0.001um/ step]
*ENG [-512 to 511 / 0 / 1dot/step]
*ENG [-1 to 1 / 0 / 0.01dot/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-2 to 2 / 0 / 0.001line/step]
*ENG [-32 to 32 / 0 / 0.01dot/step]
*ENG [-32 to 32 / 0 / 0.01dot/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-2 to 2 / 0 / 0.001line/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-2 to 2 / 0 / 0.001line/step]
*ENG [-1 to 1 / 0 / 0.001line/step]
185
186
3. Engine SP Mode Tables
2-181-059 S. Cor.: 1200 Sub :High
2-181-060 S. Cor.: 1200 Sub :Low
2-181-061 S. Cor.: 1200 Sub :Middle
2-181-064 M. Cor.: Dot: K
2-181-072 LineSift: StandardSpeed: M
2-181-073 LineSift: MidSpeed: M
2-181-074 LineSift: StandardSpeed: C
2-181-075 LineSift: MidSpeed: C
2-181-076 LineSift: StandardSpeed: Y
2-181-077 LineSift: MidSpeed: Y
2-181-080 Detect Diff.: M
2-181-081 Detect Diff.: C
2-181-082 Detect Diff.: Y
2182 [Line Position Adj. Offset]
2-182-004 M. Scan: Standard: Dot: M
2-182-005 M. Scan: Standard: Subdot: M
2-182-006 M. Scan: Middle: Dot: M
2-182-007 M. Scan: Middle: Subdot: M
2-182-008 M. Scan: Low: Dot: M
2-182-009 M. Scan: Low: Subdot: M
2-182-010 M. Scan: Standard: Dot: C
2-182-011 M. Scan: Standard: Subdot: C
2-182-012 M. Scan: Middle: Dot: C
2-182-013 M. Scan: Middle: Subdot: C
2-182-014 M. Scan: Low: Dot: C
*ENG [-2 to 2 / 0 / 0.001line/step]
*ENG [-2 to 2 / 0 / 0.001line/step]
*ENG [-2 to 2 / 0 / 0.001line/step]
*ENG [-512 to 511 / 0 / 1dot/step]
*ENG [0 to 3 / 0 / 1line/step]
*ENG [0 to 1 / 0 / 1line/step]
*ENG [0 to 3 / 0 / 1line/step]
*ENG [0 to 1 / 0 / 1line/step]
*ENG [0 to 3 / 0 / 1line/step]
*ENG [0 to 1 / 0 / 1line/step]
*ENG [-1000 to 1000 / 0 / 0.1/step]
*ENG [-1000 to 1000 / 0 / 0.1/step]
*ENG [-1000 to 1000 / 0 / 0.1/step]
*ENG [-512 to 511 / 0 / 1dot/step]
*ENG [-1 to 1 / 0 / 0.01dot/step]
*ENG [-512 to 511 / 0 / 1dot/step]
*ENG [-1 to 1 / 0 / 0.01dot/step]
*ENG [-512 to 511 / 0 / 1dot/step]
*ENG [-1 to 1 / 0 / 0.01dot/step]
*ENG [-512 to 511 / 0 / 1dot/step]
*ENG [-1 to 1 / 0 / 0.01dot/step]
*ENG [-512 to 511 / 0 / 1dot/step]
*ENG [-1 to 1 / 0 / 0.01dot/step]
*ENG [-512 to 511 / 0 / 1dot/step]
Engine SP Tables - SP2000-1
2-182-015 M. Scan: Low: Subdot: C
2-182-016 M. Scan: Standard: Dot: Y
2-182-017 M. Scan: Standard: Subdot: Y
2-182-018 M. Scan: Middle: Dot: Y
2-182-019 M. Scan: Middle: Subdot: Y
2-182-020 M. Scan: Low: Dot: Y
2-182-021 M. Scan: Low: Subdot: Y
2-182-022 S. Scan: Standard: Line: M
2-182-023 S. Scan: Standard: Subline: M
2-182-024 S. Scan: Middle: Line: M
2-182-025 S. Scan: Middle: Subline: M
2-182-026 S. Scan: Low: Line: M
2-182-027 S. Scan: Low: Subline: M
2-182-028 S. Scan: Standard: Line: C
2-182-029 S. Scan: Standard: Subline: C
2-182-030 S. Scan: Middle: Line: C
2-182-031 S. Scan: Middle: Subline: C
2-182-032 S. Scan: Low: Line: C
2-182-033 S. Scan: Low: Subline: C
2-182-034 S. Scan: Standard: Line: Y
2-182-035 S. Scan: Standard: Subline: Y
2-182-036 S. Scan: Middle: Line: Y
2-182-037 S. Scan: Middle: Subline: Y
2-182-038 S. Scan: Low: Line: Y
2-182-039 S. Scan: Low: Subline: Y
2-182-040 M. Scan: Dot: K
*ENG [-1 to 1 / 0 / 0.01dot/step]
*ENG [-512 to 511 / 0 / 1dot/step]
*ENG [-1 to 1 / 0 / 0.01dot/step]
*ENG [-512 to 511 / 0 / 1dot/step]
*ENG [-1 to 1 / 0 / 0.01dot/step]
*ENG [-512 to 511 / 0 / 1dot/step]
*ENG [-1 to 1 / 0 / 0.01dot/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-1 to 1 / 0 / 0.01line/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-1 to 1 / 0 / 0.01line/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-1 to 1 / 0 / 0.01line/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-1 to 1 / 0 / 0.01line/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-1 to 1 / 0 / 0.01line/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-1 to 1 / 0 / 0.01line/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-1 to 1 / 0 / 0.01line/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-1 to 1 / 0 / 0.01line/step]
*ENG [-16384 to 16383 / 0 / 1line/step]
*ENG [-1 to 1 / 0 / 0.01line/step]
*ENG [-512 to 511 / 0 / 1dot/step]
187
188
3. Engine SP Mode Tables
2187 [Method Select]
2-187-002 MUSIC Pattern Length Adj.
2-187-003 Pattern Width Adj.
2-187-004 Pattern Interval Adj.
2190 [Line Position Adj.]
2-190-012 SnSErr Range
2193 [MUSIC Condition Set]
2-193-002 Page: Job End: BW+FC
2-193-003 Page: Job End: FC
2-193-004 Page: Interrupt: BW+FC
2-193-005 Page: Interrupt: FC
2-193-006 Page: Stand-By: BW
2-193-007 Page: Stand-By: FC
2-193-008 Temp.
2-193-011 Temp. 2
2-193-013 Temp. 3
2-193-016 Page: Power ON:BW+FC
2-193-017 Skew
2-193-018 Page: Low Speed: BW+FC
2-193-019 Page: Low Speed: FC
2194 [MUSIC Execution Result]
2-194-001 Year
2-194-002 Month
2-194-003 Day
*ENG [-300 to 300 / 0 / 1dot/step]
*ENG [-512 to 511 / 0 / 1dot/step]
*ENG [-512 to 511 / 0 / 1dot/step]
*ENG [0 to 3500 / 200 / 1um/step]
*ENG [0 to 999 / 500 / 1page/step]
*ENG [0 to 999 / 200 / 1page/step]
*ENG [0 to 999 / 200 / 1page/step]
*ENG [0 to 999 / 200 / 1page/step]
*ENG [0 to 999 / 100 / 1page/step]
*ENG [0 to 999 / 100 / 1page/step]
*ENG [0 to 100 / 5 / 1deg/step]
*ENG [0 to 100 / 5 / 1deg/step]
*ENG [0 to 100 / 10 / 1deg/step]
*ENG [0 to 999 / 200 / 1page/step]
*ENG [0 to 999 / 50 / 1um/step]
*ENG [0 to 999 / 50 / 1page/step]
*ENG [0 to 999 / 50 / 1page/step]
*ENG [0 to 99 / 0 / 1year/step]
*ENG [1 to 12 / 1 / 1month/step]
*ENG [1 to 31 / 1 / 1day/step]
Engine SP Tables - SP2000-1
2-194-004 Hour
2-194-005 Minute
2-194-006 Temperature
2-194-007 Execution Result
2-194-008 Number of Execution
2-194-009 Number of Failure
2-194-010 Error Result: C
2-194-011 Error Result: M
2-194-012 Error Result: Y
2-194-013 Error Result: K
2-194-014 Temperature 2
2195 [Realtime MUSIC Condition Set]
2-195-001 ON/OFF
2-195-002 Page: Interrupt: BW+FC
2-195-003 Page: Interrupt: FC
2-195-004 Temperature 4
2-195-005 Temperature 5
2220 [Skew Origin Set]
2-220-001 M: Skew Motor
2-220-002 C: Skew Motor
2-220-003 Y: Skew Motor
2221 [LD Power: Fixed]
*ENG [0 to 23 / 0 / 1hour/step]
*ENG [0 to 59 / 0 / 1minute/step]
*ENG [0 to 100 / 0 / 1deg/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 to 999999 / 0 / 1time/step]
*ENG [0 to 999999 / 0 / 1time/step]
*ENG [0 to 9 / 0 / 1/step]
*ENG [0 to 9 / 0 / 1/step]
*ENG [0 to 9 / 0 / 1/step]
*ENG [0 to 9 / 0 / 1/step]
*ENG [-10 to 100 / 0 / 1deg/step]
*ENG [0 or 1 / 1 / 1/step]
0: OFF
1: ON
*ENG [0 to 999 / 50 / 1page/step]
*ENG [0 to 999 / 50 / 1page/step]
*ENG [0 to 100 / 1 / 1deg/step]
*ENG [0 to 100 / 1 / 1deg/step]
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
189
190
3. Engine SP Mode Tables
2-221-001 K
2-221-002 C
2-221-003 M
2-221-004 Y
2229 [Develop DC Bias]
2-229-001 Standard Speed: Bk
2-229-002 Standard Speed: C
2-229-003 Standard Speed: M
2-229-004 Standard Speed: Y
2-229-005 Middle Speed Bk
2-229-006 Middle Speed C
2-229-007 Middle Speed M
2-229-008 Middle Speed Y
2-229-009 Low Speed: Bk
2-229-010 Low Speed: C
2-229-011 Low Speed: M
2-229-012 Low Speed: Y
2230 [QL Power Setting]
2-230-001 Standard Speed
2-230-002 Middle Speed
2-230-003 Low Speed
*ENG [0 to 217 / 100 / 1%/step]
*ENG
*ENG
*ENG
*ENG [0 to 800 / 550 / 1-V/step]
*ENG [0 to 800 / 550 / 1-V/step]
*ENG [0 to 800 / 550 / 1-V/step]
*ENG [0 to 800 / 550 / 1-V/step]
*ENG [0 to 800 / 550 / 1-V/step]
*ENG [0 to 800 / 550 / 1-V/step]
*ENG [0 to 800 / 550 / 1-V/step]
*ENG [0 to 800 / 550 / 1-V/step]
*ENG [0 to 800 / 550 / 1-V/step]
*ENG [0 to 800 / 550 / 1-V/step]
*ENG [0 to 800 / 550 / 1-V/step]
*ENG [0 to 800 / 550 / 1-V/step]
*ENG [0 to 100 / 26 / 1%/step]
*ENG [0 to 100 / 13 / 1%/step]
*ENG [0 to 100 / 13 / 1%/step]
2241 [Temperature/Humidity: Display]
2-241-003 Exec Interval: Extra Fan Control
2241 [AIT Temperature]
*ENG [1 to 3600 / 10 / 1sec/step]
Engine SP Tables - SP2000-1
2-241-004 AIT Temperature
2242 [TS Operation Env. Log]
2-242-001 TS<=A-3
2-242-002 A-3<TS<=A
2-242-003 A<TS<=A+3
2-242-004 A+3<TS
2-242-100 Log Clear
2250 [Interval Downmode]
2-250-001 ON/OFF Setting
ENG
ENG
ENG
ENG
[0 to 70 / 0 / 0.1deg/step]
[0 to 99999999 / 0 / 1mm/step]
[0 to 99999999 / 0 / 1mm/step]
[0 to 99999999 / 0 / 1mm/step]
ENG [0 to 99999999 / 0 / 1mm/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 1 / 1/step]
2302 [Environmental Correction:Trans]
2-302-001 Current Environmental Display
2-302-002 Forced Setting
2-302-003 Absolute Humidity:Threshold 1
2-302-004 Absolute Humidity:Threshold 2
2-302-005 Absolute Humidity:Threshold 3
2-302-006 Absolute Humidity:Threshold 4
2-302-007 Temperature:Threshold
ENG [0 to 0 / 0 / 0/step]
*ENG [0 to 6 / 0 / 1/step]
0: Sensor detect
1: LL
2: ML
3: MM
4: HM
5: HH
6: SLL
*ENG [0 to 100 / 4 / 0.01g/m
3
/step]
*ENG [0 to 100 / 8 / 0.01g/m
3
/step]
*ENG [0 to 100 / 16 / 0.01g/m
3
/step]
*ENG [0 to 100 / 24 / 0.01g/m
3
/step]
*ENG [-5 to 30 / 5 / 1deg/step]
2303 [Time-Lapse Correction]
191
192
3. Engine SP Mode Tables
2-303-001 Current Div K
2-303-002 Current Div C
2-303-003 Current Div M
2-303-004 Current Div Y
2-303-005 Correction Threshold 1_Bk
2-303-006 Correction Threshold 1_Color
2-303-007 Correction Threshold 2_Bk
2-303-008 Correction Threshold 2_Color
2-303-009 Correction Threshold 3_Bk
2-303-010
Correction Threshold 3_Color
2308 [Paper Size Correction]
2-308-001 Threshold 1
2-308-002 Threshold 2
2-308-003 Threshold 3
2-308-004 Threshold 4
2-308-005 Threshold 1
2-308-006 Threshold 2
2-308-007 Threshold 3
2-308-008 Threshold 4
2311 [Non Image Area:Bias]
2-311-001 Image Transfer
*ENG [0 to 3 / 0 / 1/step]
*ENG [0 to 3 / 0 / 1/step]
*ENG [0 to 3 / 0 / 1/step]
*ENG [0 to 3 / 0 / 1/step]
*ENG [0 to 600000 / 5000 / 10page/ step]
*ENG [0 to 600000 / 5000 / 10page/ step]
*ENG [0 to 600000 / 20000 / 10page/ step]
*ENG [0 to 600000 / 20000 / 10page/ step]
*ENG [0 to 600000 / 50000 / 10page/ step]
*ENG [0 to 600000 / 50000 / 10page/ step]
*ENG [0 to 350 / 297 / 1mm/step]
*ENG [0 to 350 / 257 / 1mm/step]
*ENG [0 to 350 / 210 / 1mm/step]
*ENG [0 to 350 / 148 / 1mm/step]
*ENG [0 to 350 / 297 / 1mm/step]
*ENG [0 to 350 / 257 / 1mm/step]
*ENG [0 to 350 / 210 / 1mm/step]
*ENG [0 to 350 / 148 / 1mm/step]
*ENG [10 to 250 / 100 / 5%/step]
Engine SP Tables - SP2000-1
2-311-002 Paper Transfer
2-311-003 Paper Transfer
2316 [Power ON:Bias]
2-316-001 Image Transfer
2326 [Transfer Roller CL:Bias]
2-326-001 Positive:befor and after JOB
2-326-002 Negative:befor and after JOB
2-326-003 Positive:befor and afterProcon
2-326-004 Negative:befor and afterProcon
2-326-005 Positive:prevention
2326 [Transfer Roller CL:Env]
2-326-011 Positive:befor and after JOB
2-326-013 Positive:befor and afterProcon
2-326-015 Positive:prevention
2351 [Common:BW:Bias]
2-351-001 Image Transfer:standard
2-351-002 Image Transfer:Middle
2-351-003 Image Transfer:low
2357 [Common:FC:Bias]
2-357-001 ImageTransfer:standard:Bk
2-357-002 ImageTransfer:standard:C
2-357-003 ImageTransfer:standard:M
2-357-004 ImageTransfer:standard:Y
*ENG [0 to 230 / 0 / 1-uA/step]
*ENG [0 to 2100 / 500 / 10V/step]
*ENG [0 to 80 / 5 / 1uA/step]
*ENG [0 to 2100 / 250 / 10V/step]
*ENG [10 to 995 / 100 / 10%/step]
*ENG [0 to 2100 / 2000 / 10V/step]
*ENG [10 to 995 / 100 / 10%/step]
*ENG [0 to 2100 / 500 / 10-V/step]
*ENG [1 to 110 / 100 / 1/step]
*ENG [1 to 110 / 100 / 1/step]
*ENG [1 to 110 / 100 / 1/step]
*ENG [0 to 60 / 28 / 1uA/step]
ENG [0 to 60 / 24 / 1uA/step]
ENG [0 to 60 / 13 / 1uA/step]
*ENG [0 to 60 / 28 / 1uA/step]
*ENG [0 to 60 / 27 / 1uA/step]
*ENG [0 to 60 / 27 / 1uA/step]
*ENG [0 to 60 / 28 / 1uA/step]
193
3. Engine SP Mode Tables
194
2-357-005 ImageTransfer:Middle:Bk
2-357-006 ImageTransfer:Middle:C
2-357-007 ImageTransfer:Middle:M
2-357-008 ImageTransfer:Middle:Y
2-357-009 Image Transfer:low:Bk
2-357-010 Image Transfer:low:C
2-357-011 Image Transfer:low:M
2-357-012 Image Transfer:low:Y
ENG [0 to 60 / 24 / 1uA/step]
ENG [0 to 60 / 24 / 1uA/step]
ENG [0 to 60 / 26 / 1uA/step]
ENG [0 to 60 / 28 / 1uA/step]
ENG [0 to 60 / 12 / 1uA/step]
ENG [0 to 60 / 11 / 1uA/step]
ENG [0 to 60 / 11 / 1uA/step]
ENG [0 to 60 / 12 / 1uA/step]
2358 [TC adjust Process Control:Bias]
2-358-001 ImageTransfer:standard:FC:Bk
2-358-002 ImageTransfer:standard:FC:C
2-358-003 ImageTransfer:standard:FC:M
2-358-004 ImageTransfer:standard:FC:Y
2-358-005 ImageTransfer:standard:Bk:Bk
*ENG [0 to 60 / 28 / 1uA/step]
*ENG [0 to 60 / 27 / 1uA/step]
*ENG [0 to 60 / 27 / 1uA/step]
*ENG [0 to 60 / 28 / 1uA/step]
*ENG [0 to 60 / 28 / 1uA/step]
2360 [Common:BW:Env.CorrectionTable]
2-360-001 Image Transfer:standard *ENG [1 to 110 / 13 / 1/step]
2-360-002 Image Transfer:Middle
2-360-003 Image Transfer:low
2-360-004 ImageTransfer:standard:Bk
2-360-005 ImageTransfer:standard:C
ENG
ENG
[1 to 110 / 2 / 1/step]
[1 to 110 / 54 / 1/step]
*ENG [1 to 110 / 13 / 1/step]
*ENG [1 to 110 / 54 / 1/step]
2-360-006 ImageTransfer:standard:M
2-360-007 ImageTransfer:standard:Y
2-360-008 ImageTransfer:Middle:Bk
2-360-009 ImageTransfer:Middle:C
2-360-010 ImageTransfer:Middle:M
*ENG [1 to 110 / 54 / 1/step]
*ENG [1 to 110 / 55 / 1/step]
ENG [1 to 110 / 1 / 1/step]
ENG [1 to 110 / 2 / 1/step]
ENG [1 to 110 / 3 / 1/step]
Engine SP Tables - SP2000-1
2-360-011 ImageTransfer:Middle:Y
2-360-012 Image Transfer:low:Bk
2-360-013 Image Transfer:low:C
2-360-014 Image Transfer:low:M
2-360-015 Image Transfer:low:Y
2361 [Time-Lapse Correction: Div 1]
2-361-001 Standard Speed: Bk
2-361-002 Mid Speed: Bk
2-361-003 Low Speed: Bk
2-361-004 Standard Speed: FC: K
2-361-005 Standard Speed: FC: C
2-361-006 Standard Speed: FC: M
2-361-007 Standard Speed: FC: Y
2-361-008 Mid Speed: FC: K
2-361-009 Mid Speed: FC: C
2-361-010 Mid Speed: FC: M
2-361-011 Mid Speed: FC: Y
2-361-012 Low Speed: FC: K
2-361-013 Low Speed: FC: C
2-361-014 Low Speed: FC: M
2-361-015 Low Speed: FC: Y
2362 [Time-Lapse Correction: Div 2]
2-362-001 Standard Speed: Bk
2-362-002 Mid Speed: Bk
2-362-003 Low Speed: Bk
ENG
ENG
[1 to 110 / 4 / 1/step]
ENG [1 to 110 / 15 / 1/step]
ENG [1 to 110 / 55 / 1/step]
ENG [1 to 110 / 56 / 1/step]
[1 to 110 / 56 / 1/step]
ENG
ENG
ENG
ENG
ENG
ENG
*ENG [1 to 60 / 2 / 1/step]
ENG
ENG
*ENG [1 to 60 / 1 / 1/step]
*ENG
*ENG
*ENG
ENG
ENG
*ENG [1 to 60 / 3 / 1/step]
ENG
ENG
195
196
3. Engine SP Mode Tables
2-362-004 Standard Speed: FC: K
2-362-005 Standard Speed: FC: C
2-362-006 Standard Speed: FC: M
2-362-007 Standard Speed: FC: Y
2-362-008 Mid Speed: FC: K
2-362-009 Mid Speed: FC: C
2-362-010 Mid Speed: FC: M
2-362-011 Mid Speed: FC: Y
2-362-012 Low Speed: FC: K
2-362-013 Low Speed: FC: C
2-362-014 Low Speed: FC: M
2-362-015 Low Speed: FC: Y
2363 [Time-Lapse Correction: Div 3]
2-363-001 Standard Speed: Bk
2-363-002 Mid Speed: Bk
2-363-003 Low Speed: Bk
ENG
ENG
ENG
ENG
ENG
*ENG [1 to 60 / 1 / 1/step]
*ENG
*ENG
*ENG
ENG
ENG
ENG
*ENG [1 to 60 / 4 / 1/step]
ENG
ENG
Engine SP Tables - SP2000-1
2-363-004 Standard Speed: FC: K
2-363-005 Standard Speed: FC: C
2-363-006 Standard Speed: FC: M
2-363-007 Standard Speed: FC: Y
2-363-008 Mid Speed: FC: K
2-363-009 Mid Speed: FC: C
2-363-010 Mid Speed: FC: M
2-363-011 Mid Speed: FC: Y
2-363-012 Low Speed: FC: K
2-363-013 Low Speed: FC: C
2-363-014 Low Speed: FC: M
2-363-015 Low Speed: FC: Y
2400 [Paper Transfer Roller Settings]
2-400-001 Width of Paper Transfer Roller
ENG
ENG
ENG
ENG
ENG
*ENG [1 to 60 / 1 / 1/step]
*ENG
*ENG
*ENG
ENG
ENG
ENG
*ENG [0 or 1 / 0 / 1/step]
0: Default roller
1: Wide roller
ENG [0 to 600 / 240 / 1min/step] 2-400-002 Detatch timing in waiting
2403 [Plain1:Bias:BW]
2-403-001 PaperTransfer:standard:1side
2-403-002 PaperTransfer:standard:2side
2-403-003 PaperTransfer:low:1side
2-403-004 PaperTransfer:low:2side
2407 [Plain1:Bias:FC]
2-407-001 PaperTransfer:standard:1side
ENG
ENG
ENG
ENG
[0 to 200 / 22 / 1-uA/step]
[0 to 200 / 22 / 1-uA/step]
[0 to 200 / 11 / 1-uA/step]
[0 to 200 / 11 / 1-uA/step]
*ENG [0 to 200 / 29 / 1-uA/step]
197
198
3. Engine SP Mode Tables
2-407-002 PaperTransfer:standard:2side
2-407-003 PaperTransfer:low:1side
2-407-004 PaperTransfer:low:2side
2411 [Plain1:SizeCorrection:BW]
2-411-001 PaperTransfer:Standard:1Sid:S1
2-411-002 PaperTransfer:Standard:2Sid:S1
2-411-003 PaperTransfer:Low:1Side:S1
2-411-004 PaperTransfer:Low:2Side:S1
2-411-005 PaperTransfer:Standard:1Sid:S2
2-411-006 PaperTransfer:Standard:2Sid:S2
2-411-007 PaperTransfer:Low:1Side:S2
2-411-008 PaperTransfer:Low:2Side:S2
2-411-009 PaperTransfer:Standard:1Sid:S3
2-411-010 PaperTransfer:Standard:2Sid:S3
2-411-011 PaperTransfer:Low:1Side:S3
2-411-012 PaperTransfer:Low:2Side:S3
2-411-013 PaperTransfer:Standard:1Sid:S4
ENG [0 to 200 / 29 / 1-uA/step]
ENG [0 to 200 / 14 / 1-uA/step]
ENG [0 to 200 / 14 / 1-uA/step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
Engine SP Tables - SP2000-1
2-411-014 PaperTransfer:Standard:2Sid:S4
2-411-015 PaperTransfer:Low:1Side:S4
2-411-016 PaperTransfer:Low:2Side:S4
2-411-017 PaperTransfer:Standard:1Sid:S5
ENG [100 to 995 / 131 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 131 / 1%/ step]
ENG [100 to 995 / 132 / 1%/ step]
2-411-018 PaperTransfer:Standard:2Sid:S5
2-411-019 PaperTransfer:Low:1Side:S5
ENG [100 to 995 / 184 / 1%/ step]
ENG [100 to 995 / 132 / 1%/ step]
2-411-020 PaperTransfer:Low:2Side:S5
2-411-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
2-411-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [100 to 995 / 184 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
2-411-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-411-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-411-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
ENG [100 to 995 / 100 / 1%/ step]
2-411-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [100 to 995 / 105 / 1%/ step]
2-411-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [100 to 995 / 100 / 1%/ step]
2-411-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [100 to 995 / 105 / 1%/ step]
2-411-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
ENG [100 to 995 / 105 / 1%/ step]
199
200
3. Engine SP Mode Tables
2-411-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [100 to 995 / 118 / 1%/ step]
2-411-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [100 to 995 / 105 / 1%/ step]
2-411-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [100 to 995 / 118 / 1%/ step]
2-411-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
ENG [100 to 995 / 118 / 1%/ step]
2-411-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG [100 to 995 / 131 / 1%/ step]
2-411-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [100 to 995 / 118 / 1%/ step]
2-411-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [100 to 995 / 131 / 1%/ step]
2-411-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
ENG [100 to 995 / 132 / 1%/ step]
2-411-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [100 to 995 / 184 / 1%/ step]
2-411-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [100 to 995 / 132 / 1%/ step]
2-411-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG
[100 to 995 / 184 / 1%/ step]
2412 [Plain1:SizeCorrection:FC]
2-412-001 PaperTransfer:Standard:1Sid:S1
2-412-002 PaperTransfer:Standard:2Sid:S1
2-412-003 PaperTransfer:Low:1Side:S1
2-412-004 PaperTransfer:Low:2Side:S1
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
2-412-005 PaperTransfer:Standard:1Sid:S2
2-412-006 PaperTransfer:Standard:2Sid:S2
2-412-007 PaperTransfer:Low:1Side:S2
2-412-008 PaperTransfer:Low:2Side:S2
2-412-009 PaperTransfer:Standard:1Sid:S3
2-412-010 PaperTransfer:Standard:2Sid:S3
2-412-011 PaperTransfer:Low:1Side:S3
2-412-012 PaperTransfer:Low:2Side:S3
2-412-013 PaperTransfer:Standard:1Sid:S4
2-412-014 PaperTransfer:Standard:2Sid:S4
2-412-015 PaperTransfer:Low:1Side:S4
2-412-016 PaperTransfer:Low:2Side:S4
2-412-017 PaperTransfer:Standard:1Sid:S5
2-412-018 PaperTransfer:Standard:2Sid:S5
2-412-019 PaperTransfer:Low:1Side:S5
2-412-020 PaperTransfer:Low:2Side:S5
Engine SP Tables - SP2000-1
ENG [100 to 995 / 120 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 120 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 180 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 180 / 1%/ step]
ENG [100 to 995 / 130 / 1%/ step]
ENG [100 to 995 / 200 / 1%/ step]
ENG [100 to 995 / 130 / 1%/ step]
ENG [100 to 995 / 200 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 240 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 240 / 1%/ step]
201
202
3. Engine SP Mode Tables
2-412-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
2-412-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
2-412-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-412-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-412-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
2-412-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [100 to 995 / 120 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
2-412-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [100 to 995 / 120 / 1%/ step]
2-412-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [100 to 995 / 140 / 1%/ step]
2-412-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
2-412-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 180 / 1%/ step]
2-412-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [100 to 995 / 118 / 1%/ step]
2-412-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [100 to 995 / 180 / 1%/ step]
2-412-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
2-412-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG [100 to 995 / 130 / 1%/ step]
ENG [100 to 995 / 200 / 1%/ step]
2-412-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [100 to 995 / 130 / 1%/ step]
2-412-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [100 to 995 / 200 / 1%/ step]
Engine SP Tables - SP2000-1
2-412-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
2-412-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 240 / 1%/ step]
2-412-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [100 to 995 / 140 / 1%/ step]
2-412-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [100 to 995 / 240 / 1%/ step]
2413 [Plain1:Size-Env.Correct:BW]
2-413-001 PaperTransfer:Standard:1Sid:S1
2-413-002 PaperTransfer:Standard:2Sid:S1
2-413-003 PaperTransfer:Low:1Side:S1
2-413-004 PaperTransfer:Low:2Side:S1
2-413-005 PaperTransfer:Standard:1Sid:S2
2-413-006 PaperTransfer:Standard:2Sid:S2
2-413-007 PaperTransfer:Low:1Side:S2
2-413-008 PaperTransfer:Low:2Side:S2
2-413-009 PaperTransfer:Standard:1Sid:S3
2-413-010 PaperTransfer:Standard:2Sid:S3
2-413-011 PaperTransfer:Low:1Side:S3
2-413-012 PaperTransfer:Low:2Side:S3
2-413-013 PaperTransfer:Standard:1Sid:S4
2-413-014 PaperTransfer:Standard:2Sid:S4
2-413-015 PaperTransfer:Low:1Side:S4
2-413-016 PaperTransfer:Low:2Side:S4
2-413-017 PaperTransfer:Standard:1Sid:S5
2-413-018 PaperTransfer:Standard:2Sid:S5
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[1 to 110 / 10 / 1/step]
[1 to 110 / 15 / 1/step]
[1 to 110 / 10 / 1/step]
[1 to 110 / 15 / 1/step]
[1 to 110 / 11 / 1/step]
[1 to 110 / 16 / 1/step]
[1 to 110 / 11 / 1/step]
[1 to 110 / 16 / 1/step]
[1 to 110 / 12 / 1/step]
[1 to 110 / 17 / 1/step]
[1 to 110 / 12 / 1/step]
[1 to 110 / 17 / 1/step]
[1 to 110 / 13 / 1/step]
ENG [1 to 110 / 18 / 1/step]
ENG [1 to 110 / 13 / 1/step]
[1 to 110 / 18 / 1/step]
[1 to 110 / 14 / 1/step]
[1 to 110 / 19 / 1/step]
203
204
3. Engine SP Mode Tables
2-413-019 PaperTransfer:Low:1Side:S5 ENG [1 to 110 / 14 / 1/step]
2-413-020 PaperTransfer:Low:2Side:S5
2-413-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
ENG
ENG
[1 to 110 / 19 / 1/step]
[1 to 110 / 10 / 1/step]
2-413-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [1 to 110 / 15 / 1/step]
2-413-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [1 to 110 / 10 / 1/step]
2-413-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [1 to 110 / 15 / 1/step]
2-413-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
ENG [1 to 110 / 11 / 1/step]
2-413-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [1 to 110 / 16 / 1/step]
2-413-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [1 to 110 / 11 / 1/step]
2-413-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [1 to 110 / 16 / 1/step]
2-413-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
ENG [1 to 110 / 12 / 1/step]
2-413-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [1 to 110 / 17 / 1/step]
2-413-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [1 to 110 / 12 / 1/step]
2-413-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [1 to 110 / 17 / 1/step]
2-413-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
ENG [1 to 110 / 13 / 1/step]
2-413-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG [1 to 110 / 18 / 1/step]
2-413-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [1 to 110 / 13 / 1/step]
2-413-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [1 to 110 / 18 / 1/step]
ENG [1 to 110 / 14 / 1/step] 2-413-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
2-413-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [1 to 110 / 19 / 1/step]
Engine SP Tables - SP2000-1
2-413-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [1 to 110 / 14 / 1/step]
2-413-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [1 to 110 / 19 / 1/step]
2414 [Plain1:Size-Env.Correct:FC]
2-414-001 PaperTransfer:Standard:1Sid:S1
2-414-002 PaperTransfer:Standard:2Sid:S1
2-414-003 PaperTransfer:Low:1Side:S1
2-414-004 PaperTransfer:Low:2Side:S1
2-414-005 PaperTransfer:Standard:1Sid:S2
2-414-006 PaperTransfer:Standard:2Sid:S2
2-414-007 PaperTransfer:Low:1Side:S2
2-414-008 PaperTransfer:Low:2Side:S2
2-414-009 PaperTransfer:Standard:1Sid:S3
2-414-010 PaperTransfer:Standard:2Sid:S3
2-414-011 PaperTransfer:Low:1Side:S3
2-414-012 PaperTransfer:Low:2Side:S3
2-414-013 PaperTransfer:Standard:1Sid:S4
2-414-014 PaperTransfer:Standard:2Sid:S4
2-414-015 PaperTransfer:Low:1Side:S4
2-414-016 PaperTransfer:Low:2Side:S4
2-414-017 PaperTransfer:Standard:1Sid:S5
2-414-018 PaperTransfer:Standard:2Sid:S5
2-414-019 PaperTransfer:Low:1Side:S5
2-414-020 PaperTransfer:Low:2Side:S5
2-414-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
*ENG [1 to 110 / 20 / 1/step]
ENG [1 to 110 / 25 / 1/step]
ENG [1 to 110 / 20 / 1/step]
ENG [1 to 110 / 25 / 1/step]
ENG [1 to 110 / 21 / 1/step]
ENG [1 to 110 / 26 / 1/step]
ENG [1 to 110 / 21 / 1/step]
ENG [1 to 110 / 26 / 1/step]
ENG [1 to 110 / 22 / 1/step]
ENG [1 to 110 / 27 / 1/step]
ENG [1 to 110 / 22 / 1/step]
ENG [1 to 110 / 27 / 1/step]
ENG [1 to 110 / 23 / 1/step]
ENG [1 to 110 / 28 / 1/step]
ENG [1 to 110 / 23 / 1/step]
ENG [1 to 110 / 28 / 1/step]
ENG [1 to 110 / 24 / 1/step]
ENG [1 to 110 / 29 / 1/step]
ENG [1 to 110 / 24 / 1/step]
ENG [1 to 110 / 29 / 1/step]
*ENG [1 to 110 / 20 / 1/step]
205
206
3. Engine SP Mode Tables
2-414-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [1 to 110 / 25 / 1/step]
2-414-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [1 to 110 / 20 / 1/step]
2-414-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [1 to 110 / 25 / 1/step]
2-414-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
ENG [1 to 110 / 21 / 1/step]
2-414-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [1 to 110 / 26 / 1/step]
2-414-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [1 to 110 / 21 / 1/step]
2-414-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [1 to 110 / 26 / 1/step]
2-414-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
ENG [1 to 110 / 22 / 1/step]
2-414-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [1 to 110 / 27 / 1/step]
2-414-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [1 to 110 / 22 / 1/step]
2-414-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [1 to 110 / 27 / 1/step]
2-414-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
ENG [1 to 110 / 23 / 1/step]
2-414-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG [1 to 110 / 28 / 1/step]
2-414-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [1 to 110 / 23 / 1/step]
2-414-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [1 to 110 / 28 / 1/step]
2-414-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
ENG [1 to 110 / 24 / 1/step]
2-414-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [1 to 110 / 29 / 1/step]
2-414-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [1 to 110 / 24 / 1/step]
2-414-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [1 to 110 / 29 / 1/step]
2415 [Plain1:LeadingEdgeCorrection]
2-415-001 PaperTransfer:Standard:1Side
2-415-002 PaperTransfer:Standard:2Side
2-415-003 Paper Transfer:Low:1side
2-415-004 Paper Transfer:Low:2side
2416 [Plain1:SwitchTimingLeadEdge]
2-416-001 PaperTransfer:Standard:1side
2-416-002 PaperTransfer:Standard:2side
2-416-003 Paper Transfer:Low:1side
2-416-004 Paper Transfer:Low:2side
2417 [Plain1:TrailEdgeCorrection]
2-417-001 PaperTransfer:Standard:1Side
2-417-002 PaperTransfer:Standard:2Side
2-417-003 Paper Transfer:Low:1side
2-417-004 Paper Transfer:Low:2side
2418 [Plain1:SwitchTimingTrailEdge]
2-418-001 PaperTransfer:Standard:1side
2-418-002 PaperTransfer:Standard:2side
2-418-003 Paper Transfer:Low:1side
2-418-004 Paper Transfer:Low:2side
2423 [Plain2:Bias:BW]
2-423-001 PaperTransfer:standard:1side
2-423-002 PaperTransfer:standard:2side
2-423-003 PaperTransfer:low:1side
Engine SP Tables - SP2000-1
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 200 / 22 / 1-uA/step]
ENG [0 to 200 / 22 / 1-uA/step]
ENG [0 to 200 / 11 / 1-uA/step]
207
208
3. Engine SP Mode Tables
2-423-004 PaperTransfer:low:2side
2425 [Hhsmall:LeadEdgeCorrection]
2-425-001 PaperTransfer:1side
2-425-002 PaperTransfer:2stSide
2427 [Plain2:Bias:FC]
2-427-001 PaperTransfer:standard:1side
2-427-002 PaperTransfer:standard:2side
2-427-003 PaperTransfer:low:1side
2-427-004 PaperTransfer:low:2side
2431 [Plain2:SizeCorrection:BW]
2-431-001 PaperTransfer:Standard:1Sid:S1
2-431-002 PaperTransfer:Standard:2Sid:S1
2-431-003 PaperTransfer:Low:1Side:S1
2-431-004 PaperTransfer:Low:2Side:S1
2-431-005 PaperTransfer:Standard:1Sid:S2
2-431-006 PaperTransfer:Standard:2Sid:S2
2-431-007 PaperTransfer:Low:1Side:S2
2-431-008 PaperTransfer:Low:2Side:S2
2-431-009 PaperTransfer:Standard:1Sid:S3
ENG [0 to 200 / 11 / 1-uA/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 200 / 29 / 1-uA/step]
ENG [0 to 200 / 29 / 1-uA/step]
ENG [0 to 200 / 14 / 1-uA/step]
ENG [0 to 200 / 14 / 1-uA/step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
Engine SP Tables - SP2000-1
2-431-010 PaperTransfer:Standard:2Sid:S3
2-431-011 PaperTransfer:Low:1Side:S3
2-431-012 PaperTransfer:Low:2Side:S3
2-431-013 PaperTransfer:Standard:1Sid:S4
2-431-014 PaperTransfer:Standard:2Sid:S4
2-431-015 PaperTransfer:Low:1Side:S4
2-431-016 PaperTransfer:Low:2Side:S4
2-431-017 PaperTransfer:Standard:1Sid:S5
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 131 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 131 / 1%/ step]
ENG [100 to 995 / 132 / 1%/ step]
2-431-018 PaperTransfer:Standard:2Sid:S5
2-431-019 PaperTransfer:Low:1Side:S5
ENG [100 to 995 / 184 / 1%/ step]
ENG [100 to 995 / 132 / 1%/ step]
2-431-020 PaperTransfer:Low:2Side:S5
2-431-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
2-431-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [100 to 995 / 184 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
2-431-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-431-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-431-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
ENG [100 to 995 / 100 / 1%/ step]
209
210
3. Engine SP Mode Tables
2-431-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [100 to 995 / 105 / 1%/ step]
2-431-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [100 to 995 / 100 / 1%/ step]
2-431-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [100 to 995 / 105 / 1%/ step]
2-431-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
ENG [100 to 995 / 105 / 1%/ step]
2-431-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [100 to 995 / 118 / 1%/ step]
2-431-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [100 to 995 / 105 / 1%/ step]
2-431-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [100 to 995 / 118 / 1%/ step]
2-431-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
ENG [100 to 995 / 118 / 1%/ step]
2-431-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG [100 to 995 / 131 / 1%/ step]
2-431-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [100 to 995 / 118 / 1%/ step]
2-431-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [100 to 995 / 131 / 1%/ step]
2-431-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
ENG [100 to 995 / 132 / 1%/ step]
2-431-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [100 to 995 / 184 / 1%/ step]
2-431-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [100 to 995 / 132 / 1%/ step]
2-431-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [100 to 995 / 184 / 1%/ step]
2432 [Plain2:SizeCorrection:FC]
2-432-001 PaperTransfer:Standard:1Sid:S1
2-432-002 PaperTransfer:Standard:2Sid:S1
2-432-003 PaperTransfer:Low:1Side:S1
2-432-004 PaperTransfer:Low:2Side:S1
2-432-005 PaperTransfer:Standard:1Sid:S2
2-432-006 PaperTransfer:Standard:2Sid:S2
2-432-007 PaperTransfer:Low:1Side:S2
2-432-008 PaperTransfer:Low:2Side:S2
2-432-009 PaperTransfer:Standard:1Sid:S3
2-432-010 PaperTransfer:Standard:2Sid:S3
2-432-011 PaperTransfer:Low:1Side:S3
2-432-012 PaperTransfer:Low:2Side:S3
2-432-013 PaperTransfer:Standard:1Sid:S4
2-432-014 PaperTransfer:Standard:2Sid:S4
2-432-015 PaperTransfer:Low:1Side:S4
2-432-016 PaperTransfer:Low:2Side:S4
Engine SP Tables - SP2000-1
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 120 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 120 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 180 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 180 / 1%/ step]
ENG [100 to 995 / 130 / 1%/ step]
ENG [100 to 995 / 200 / 1%/ step]
ENG [100 to 995 / 130 / 1%/ step]
ENG [100 to 995 / 200 / 1%/ step]
211
212
3. Engine SP Mode Tables
2-432-017 PaperTransfer:Standard:1Sid:S5
2-432-018 PaperTransfer:Standard:2Sid:S5
2-432-019 PaperTransfer:Low:1Side:S5
2-432-020 PaperTransfer:Low:2Side:S5
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 240 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 240 / 1%/ step]
2-432-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
2-432-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
2-432-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-432-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-432-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
2-432-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [100 to 995 / 120 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
2-432-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [100 to 995 / 120 / 1%/ step]
2-432-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [100 to 995 / 140 / 1%/ step]
2-432-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
2-432-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 180 / 1%/ step]
2-432-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [100 to 995 / 118 / 1%/ step]
2-432-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [100 to 995 / 180 / 1%/ step]
Engine SP Tables - SP2000-1
2-432-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
2-432-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG [100 to 995 / 130 / 1%/ step]
ENG [100 to 995 / 200 / 1%/ step]
2-432-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [100 to 995 / 130 / 1%/ step]
2-432-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [100 to 995 / 200 / 1%/ step]
2-432-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
2-432-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 240 / 1%/ step]
2-432-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [100 to 995 / 140 / 1%/ step]
2-432-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [100 to 995 / 240 / 1%/ step]
2433 [Plain2:Size-Env.Correct:BW]
2-433-001 PaperTransfer:Standard:1Sid:S1
2-433-002 PaperTransfer:Standard:2Sid:S1
2-433-003 PaperTransfer:Low:1Side:S1
2-433-004 PaperTransfer:Low:2Side:S1
2-433-005 PaperTransfer:Standard:1Sid:S2
2-433-006 PaperTransfer:Standard:2Sid:S2
2-433-007 PaperTransfer:Low:1Side:S2
2-433-008 PaperTransfer:Low:2Side:S2
2-433-009 PaperTransfer:Standard:1Sid:S3
2-433-010 PaperTransfer:Standard:2Sid:S3
2-433-011 PaperTransfer:Low:1Side:S3
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[1 to 110 / 10 / 1/step]
[1 to 110 / 15 / 1/step]
[1 to 110 / 10 / 1/step]
[1 to 110 / 15 / 1/step]
[1 to 110 / 11 / 1/step]
[1 to 110 / 16 / 1/step]
[1 to 110 / 11 / 1/step]
[1 to 110 / 16 / 1/step]
[1 to 110 / 12 / 1/step]
ENG [1 to 110 / 17 / 1/step]
ENG [1 to 110 / 12 / 1/step]
213
214
3. Engine SP Mode Tables
2-433-012 PaperTransfer:Low:2Side:S3
2-433-013 PaperTransfer:Standard:1Sid:S4
2-433-014 PaperTransfer:Standard:2Sid:S4
2-433-015 PaperTransfer:Low:1Side:S4
2-433-016 PaperTransfer:Low:2Side:S4
2-433-017 PaperTransfer:Standard:1Sid:S5
2-433-018 PaperTransfer:Standard:2Sid:S5
2-433-019 PaperTransfer:Low:1Side:S5
2-433-020 PaperTransfer:Low:2Side:S5
2-433-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
2-433-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG
ENG
ENG
ENG
ENG
[1 to 110 / 17 / 1/step]
ENG [1 to 110 / 13 / 1/step]
ENG [1 to 110 / 18 / 1/step]
ENG [1 to 110 / 13 / 1/step]
ENG [1 to 110 / 18 / 1/step]
ENG [1 to 110 / 14 / 1/step]
ENG [1 to 110 / 19 / 1/step]
[1 to 110 / 14 / 1/step]
[1 to 110 / 19 / 1/step]
[1 to 110 / 10 / 1/step]
[1 to 110 / 15 / 1/step]
2-433-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [1 to 110 / 10 / 1/step]
2-433-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [1 to 110 / 15 / 1/step]
ENG [1 to 110 / 11 / 1/step] 2-433-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
2-433-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [1 to 110 / 16 / 1/step]
2-433-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [1 to 110 / 11 / 1/step]
2-433-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [1 to 110 / 16 / 1/step]
ENG [1 to 110 / 12 / 1/step] 2-433-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
2-433-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [1 to 110 / 17 / 1/step]
2-433-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [1 to 110 / 12 / 1/step]
2-433-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [1 to 110 / 17 / 1/step]
Engine SP Tables - SP2000-1
2-433-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
2-433-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG
ENG
[1 to 110 / 13 / 1/step]
[1 to 110 / 18 / 1/step]
2-433-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [1 to 110 / 13 / 1/step]
2-433-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [1 to 110 / 18 / 1/step]
2-433-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
ENG [1 to 110 / 14 / 1/step]
2-433-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [1 to 110 / 19 / 1/step]
2-433-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [1 to 110 / 14 / 1/step]
2-433-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [1 to 110 / 19 / 1/step]
2434 [Plain2:Size-Env.Correct:FC]
2-434-001 PaperTransfer:Standard:1Sid:S1
2-434-002 PaperTransfer:Standard:2Sid:S1
2-434-003 PaperTransfer:Low:1Side:S1
2-434-004 PaperTransfer:Low:2Side:S1
2-434-005 PaperTransfer:Standard:1Sid:S2
2-434-006 PaperTransfer:Standard:2Sid:S2
2-434-007 PaperTransfer:Low:1Side:S2
2-434-008 PaperTransfer:Low:2Side:S2
2-434-009 PaperTransfer:Standard:1Sid:S3
2-434-010 PaperTransfer:Standard:2Sid:S3
2-434-011 PaperTransfer:Low:1Side:S3
2-434-012 PaperTransfer:Low:2Side:S3
2-434-013 PaperTransfer:Standard:1Sid:S4
2-434-014 PaperTransfer:Standard:2Sid:S4
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[1 to 110 / 20 / 1/step]
[1 to 110 / 25 / 1/step]
[1 to 110 / 20 / 1/step]
[1 to 110 / 25 / 1/step]
[1 to 110 / 21 / 1/step]
[1 to 110 / 26 / 1/step]
[1 to 110 / 21 / 1/step]
[1 to 110 / 26 / 1/step]
[1 to 110 / 22 / 1/step]
ENG [1 to 110 / 27 / 1/step]
ENG [1 to 110 / 22 / 1/step]
[1 to 110 / 27 / 1/step]
[1 to 110 / 23 / 1/step]
[1 to 110 / 28 / 1/step]
215
216
3. Engine SP Mode Tables
2-434-015 PaperTransfer:Low:1Side:S4
2-434-016 PaperTransfer:Low:2Side:S4
2-434-017 PaperTransfer:Standard:1Sid:S5
ENG [1 to 110 / 23 / 1/step]
ENG [1 to 110 / 28 / 1/step]
ENG [1 to 110 / 24 / 1/step]
2-434-018 PaperTransfer:Standard:2Sid:S5
2-434-019 PaperTransfer:Low:1Side:S5
ENG
ENG
[1 to 110 / 29 / 1/step]
[1 to 110 / 24 / 1/step]
2-434-020 PaperTransfer:Low:2Side:S5
2-434-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
ENG
ENG
[1 to 110 / 29 / 1/step]
[1 to 110 / 20 / 1/step]
2-434-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [1 to 110 / 25 / 1/step]
2-434-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [1 to 110 / 20 / 1/step]
2-434-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [1 to 110 / 25 / 1/step]
2-434-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
ENG [1 to 110 / 21 / 1/step]
2-434-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [1 to 110 / 26 / 1/step]
2-434-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [1 to 110 / 21 / 1/step]
2-434-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [1 to 110 / 26 / 1/step]
2-434-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
ENG [1 to 110 / 22 / 1/step]
2-434-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [1 to 110 / 27 / 1/step]
2-434-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [1 to 110 / 22 / 1/step]
2-434-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [1 to 110 / 27 / 1/step]
2-434-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
2-434-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG
ENG
[1 to 110 / 23 / 1/step]
[1 to 110 / 28 / 1/step]
2-434-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [1 to 110 / 23 / 1/step]
Engine SP Tables - SP2000-1
2-434-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [1 to 110 / 28 / 1/step]
2-434-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
ENG [1 to 110 / 24 / 1/step]
2-434-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [1 to 110 / 29 / 1/step]
2-434-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [1 to 110 / 24 / 1/step]
2-434-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [1 to 110 / 29 / 1/step]
2435 [Plain2:LeadingEdgeCorrection]
2-435-001 PaperTransfer:Standard:1Side
2-435-002 PaperTransfer:Standard:2Side
2-435-003 Paper Transfer:Low:1side
2-435-004 Paper Transfer:Low:2side
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
2436 [Plain2:SwitchTimingLeadEdge]
2-436-001 PaperTransfer:Standard:1side
2-436-002 PaperTransfer:Standard:2side
2-436-003 Paper Transfer:Low:1side
2-436-004 Paper Transfer:Low:2side
2437 [Plain2:TrailEdgeCorrection]
2-437-001 PaperTransfer:Standard:1Side
2-437-002 PaperTransfer:Standard:2Side
2-437-003 Paper Transfer:Low:1side
2-437-004 Paper Transfer:Low:2side
2438 [Plain2:SwitchTimingTrailEdge]
2-438-001 PaperTransfer:Standard:1side
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 50 / 0 / 2mm/step]
217
218
3. Engine SP Mode Tables
2-438-002 PaperTransfer:Standard:2side
2-438-003 Paper Transfer:Low:1side
2-438-004 Paper Transfer:Low:2side
2443 [Middle:Bias:BW]
2-443-001 PaperTransfer:standard:1side
2-443-002 PaperTransfer:standard:2side
2-443-003 PaperTransfer:low:1side
2-443-004 PaperTransfer:low:2side
2447 [Middle:Bias:FC]
2-447-001 PaperTransfer:standard:1side
2-447-002 PaperTransfer:standard:2side
2-447-003 PaperTransfer:low:1side
2-447-004 PaperTransfer:low:2side
2451 [Middle:SizeCorrection:BW]
2-451-001 PaperTransfer:Standard:1Sid:S1
2-451-002 PaperTransfer:Standard:2Sid:S1
2-451-003 PaperTransfer:Low:1Side:S1
2-451-004 PaperTransfer:Low:2Side:S1
2-451-005 PaperTransfer:Standard:1Sid:S2
2-451-006 PaperTransfer:Standard:2Sid:S2
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 200 / 22 / 1-uA/step]
ENG [0 to 200 / 22 / 1-uA/step]
ENG [0 to 200 / 11 / 1-uA/step]
ENG [0 to 200 / 11 / 1-uA/step]
ENG [0 to 200 / 29 / 1-uA/step]
ENG [0 to 200 / 29 / 1-uA/step]
ENG [0 to 200 / 14 / 1-uA/step]
ENG [0 to 200 / 14 / 1-uA/step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 106 / 1%/ step]
Engine SP Tables - SP2000-1
2-451-007 PaperTransfer:Low:1Side:S2
2-451-008 PaperTransfer:Low:2Side:S2
2-451-009 PaperTransfer:Standard:1Sid:S3
2-451-010 PaperTransfer:Standard:2Sid:S3
2-451-011 PaperTransfer:Low:1Side:S3
2-451-012 PaperTransfer:Low:2Side:S3
2-451-013 PaperTransfer:Standard:1Sid:S4
2-451-014 PaperTransfer:Standard:2Sid:S4
2-451-015 PaperTransfer:Low:1Side:S4
2-451-016 PaperTransfer:Low:2Side:S4
2-451-017 PaperTransfer:Standard:1Sid:S5
2-451-018 PaperTransfer:Standard:2Sid:S5
2-451-019 PaperTransfer:Low:1Side:S5
2-451-020 PaperTransfer:Low:2Side:S5
2-451-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
2-451-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 106 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 110 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 110 / 1%/ step]
ENG [100 to 995 / 113 / 1%/ step]
ENG [100 to 995 / 120 / 1%/ step]
ENG [100 to 995 / 113 / 1%/ step]
ENG [100 to 995 / 120 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
219
220
3. Engine SP Mode Tables
2-451-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-451-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-451-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
2-451-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG
ENG
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 106 / 1%/ step]
2-451-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [100 to 995 / 100 / 1%/ step]
2-451-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [100 to 995 / 106 / 1%/ step]
2-451-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
2-451-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG
ENG
[100 to 995 / 105 / 1%/ step]
[100 to 995 / 110 / 1%/ step]
2-451-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [100 to 995 / 105 / 1%/ step]
2-451-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [100 to 995 / 110 / 1%/ step]
2-451-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
2-451-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG
ENG
[100 to 995 / 113 / 1%/ step]
[100 to 995 / 120 / 1%/ step]
2-451-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [100 to 995 / 113 / 1%/ step]
2-451-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [100 to 995 / 120 / 1%/ step]
2-451-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
2-451-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG
ENG
[100 to 995 / 118 / 1%/ step]
[100 to 995 / 140 / 1%/ step]
Engine SP Tables - SP2000-1
2-451-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [100 to 995 / 118 / 1%/ step]
2-451-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [100 to 995 / 140 / 1%/ step]
2452 [Middle:SizeCorrection:FC]
2-452-001 PaperTransfer:Standard:1Sid:S1
2-452-002 PaperTransfer:Standard:2Sid:S1
2-452-003 PaperTransfer:Low:1Side:S1
2-452-004 PaperTransfer:Low:2Side:S1
2-452-005 PaperTransfer:Standard:1Sid:S2
2-452-006 PaperTransfer:Standard:2Sid:S2
2-452-007 PaperTransfer:Low:1Side:S2
2-452-008 PaperTransfer:Low:2Side:S2
2-452-009 PaperTransfer:Standard:1Sid:S3
2-452-010 PaperTransfer:Standard:2Sid:S3
2-452-011 PaperTransfer:Low:1Side:S3
2-452-012 PaperTransfer:Low:2Side:S3
2-452-013 PaperTransfer:Standard:1Sid:S4
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 106 / 1%/ step]
ENG [100 to 995 / 132 / 1%/ step]
ENG [100 to 995 / 106 / 1%/ step]
ENG [100 to 995 / 132 / 1%/ step]
ENG [100 to 995 / 110 / 1%/ step]
ENG [100 to 995 / 170 / 1%/ step]
ENG [100 to 995 / 110 / 1%/ step]
ENG [100 to 995 / 170 / 1%/ step]
ENG [100 to 995 / 120 / 1%/ step]
221
222
3. Engine SP Mode Tables
2-452-014 PaperTransfer:Standard:2Sid:S4
2-452-015 PaperTransfer:Low:1Side:S4
2-452-016 PaperTransfer:Low:2Side:S4
2-452-017 PaperTransfer:Standard:1Sid:S5
2-452-018 PaperTransfer:Standard:2Sid:S5
2-452-019 PaperTransfer:Low:1Side:S5
2-452-020 PaperTransfer:Low:2Side:S5
2-452-001 PaperTransfer:Standard:1Sid:S1
ENG [100 to 995 / 189 / 1%/ step]
ENG [100 to 995 / 120 / 1%/ step]
ENG [100 to 995 / 189 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 245 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 245 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
2-452-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [100 to 995 / 100 / 1%/ step]
2-452-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-452-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-452-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
ENG [100 to 995 / 106 / 1%/ step]
2-452-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [100 to 995 / 132 / 1%/ step]
2-452-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [100 to 995 / 106 / 1%/ step]
2-452-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [100 to 995 / 132 / 1%/ step]
2-452-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
ENG [100 to 995 / 110 / 1%/ step]
Engine SP Tables - SP2000-1
2-452-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [100 to 995 / 170 / 1%/ step]
2-452-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [100 to 995 / 110 / 1%/ step]
2-452-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [100 to 995 / 170 / 1%/ step]
2-452-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
ENG [100 to 995 / 120 / 1%/ step]
2-452-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG [100 to 995 / 189 / 1%/ step]
2-452-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [100 to 995 / 120 / 1%/ step]
2-452-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [100 to 995 / 189 / 1%/ step]
2-452-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
ENG [100 to 995 / 140 / 1%/ step]
2-452-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [100 to 995 / 245 / 1%/ step]
2-452-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [100 to 995 / 140 / 1%/ step]
2-452-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [100 to 995 / 245 / 1%/ step]
2453 [Middle:Size-Env.Correct:BW]
2-453-001 PaperTransfer:Standard:1Sid:S1
2-453-002 PaperTransfer:Standard:2Sid:S1
2-453-003 PaperTransfer:Low:1Side:S1
2-453-004 PaperTransfer:Low:2Side:S1
2-453-005 PaperTransfer:Standard:1Sid:S2
2-453-006 PaperTransfer:Standard:2Sid:S2
ENG
ENG
ENG
ENG
ENG
ENG
[1 to 110 / 10 / 1/step]
[1 to 110 / 41 / 1/step]
[1 to 110 / 10 / 1/step]
[1 to 110 / 41 / 1/step]
[1 to 110 / 39 / 1/step]
[1 to 110 / 42 / 1/step]
223
224
3. Engine SP Mode Tables
2-453-007 PaperTransfer:Low:1Side:S2
2-453-008 PaperTransfer:Low:2Side:S2
2-453-009 PaperTransfer:Standard:1Sid:S3
2-453-010 PaperTransfer:Standard:2Sid:S3
2-453-011 PaperTransfer:Low:1Side:S3
2-453-012 PaperTransfer:Low:2Side:S3
2-453-013 PaperTransfer:Standard:1Sid:S4
ENG [1 to 110 / 39 / 1/step]
ENG [1 to 110 / 42 / 1/step]
ENG [1 to 110 / 40 / 1/step]
ENG [1 to 110 / 43 / 1/step]
ENG [1 to 110 / 40 / 1/step]
ENG [1 to 110 / 43 / 1/step]
ENG [1 to 110 / 40 / 1/step]
2-453-014 PaperTransfer:Standard:2Sid:S4
2-453-015 PaperTransfer:Low:1Side:S4
2-453-016 PaperTransfer:Low:2Side:S4
2-453-017 PaperTransfer:Standard:1Sid:S5
2-453-018 PaperTransfer:Standard:2Sid:S5
2-453-019 PaperTransfer:Low:1Side:S5
2-453-020 PaperTransfer:Low:2Side:S5
2-453-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
2-453-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[1 to 110 / 44 / 1/step]
[1 to 110 / 40 / 1/step]
[1 to 110 / 44 / 1/step]
[1 to 110 / 40 / 1/step]
[1 to 110 / 45 / 1/step]
[1 to 110 / 40 / 1/step]
[1 to 110 / 45 / 1/step]
[1 to 110 / 10 / 1/step]
[1 to 110 / 41 / 1/step]
2-453-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [1 to 110 / 10 / 1/step]
2-453-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [1 to 110 / 41 / 1/step]
ENG [1 to 110 / 39 / 1/step] 2-453-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
2-453-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [1 to 110 / 42 / 1/step]
2-453-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [1 to 110 / 39 / 1/step]
2-453-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [1 to 110 / 42 / 1/step]
2-453-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
ENG [1 to 110 / 40 / 1/step]
Engine SP Tables - SP2000-1
2-453-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [1 to 110 / 43 / 1/step]
2-453-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [1 to 110 / 40 / 1/step]
2-453-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [1 to 110 / 43 / 1/step]
2-453-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
ENG [1 to 110 / 40 / 1/step]
2-453-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG [1 to 110 / 44 / 1/step]
2-453-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [1 to 110 / 40 / 1/step]
2-453-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [1 to 110 / 44 / 1/step]
2-453-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
ENG [1 to 110 / 40 / 1/step]
2-453-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [1 to 110 / 45 / 1/step]
2-453-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [1 to 110 / 40 / 1/step]
2-453-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [1 to 110 / 45 / 1/step]
2454 [Middle:Size-Env.Correct:FC]
2-454-001 PaperTransfer:Standard:1Sid:S1
2-454-002 PaperTransfer:Standard:2Sid:S1
2-454-003 PaperTransfer:Low:1Side:S1
2-454-004 PaperTransfer:Low:2Side:S1
2-454-005 PaperTransfer:Standard:1Sid:S2
2-454-006 PaperTransfer:Standard:2Sid:S2
2-454-007 PaperTransfer:Low:1Side:S2
2-454-008 PaperTransfer:Low:2Side:S2
2-454-009 PaperTransfer:Standard:1Sid:S3
2-454-010 PaperTransfer:Standard:2Sid:S3
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[1 to 110 / 20 / 1/step]
[1 to 110 / 49 / 1/step]
[1 to 110 / 20 / 1/step]
[1 to 110 / 49 / 1/step]
[1 to 110 / 46 / 1/step]
[1 to 110 / 50 / 1/step]
[1 to 110 / 46 / 1/step]
ENG [1 to 110 / 50 / 1/step]
ENG [1 to 110 / 47 / 1/step]
ENG [1 to 110 / 51 / 1/step]
225
226
3. Engine SP Mode Tables
2-454-011 PaperTransfer:Low:1Side:S3
2-454-012 PaperTransfer:Low:2Side:S3
2-454-013 PaperTransfer:Standard:1Sid:S4
2-454-014 PaperTransfer:Standard:2Sid:S4
2-454-015 PaperTransfer:Low:1Side:S4
2-454-016 PaperTransfer:Low:2Side:S4
2-454-017 PaperTransfer:Standard:1Sid:S5
ENG [1 to 110 / 47 / 1/step]
ENG [1 to 110 / 51 / 1/step]
ENG [1 to 110 / 48 / 1/step]
ENG [1 to 110 / 52 / 1/step]
ENG [1 to 110 / 48 / 1/step]
ENG [1 to 110 / 52 / 1/step]
ENG [1 to 110 / 48 / 1/step]
2-454-018 PaperTransfer:Standard:2Sid:S5
2-454-019 PaperTransfer:Low:1Side:S5
ENG
ENG
[1 to 110 / 53 / 1/step]
[1 to 110 / 48 / 1/step]
2-454-020 PaperTransfer:Low:2Side:S5
2-454-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
ENG
ENG
[1 to 110 / 53 / 1/step]
[1 to 110 / 20 / 1/step]
2-454-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [1 to 110 / 49 / 1/step]
2-454-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [1 to 110 / 20 / 1/step]
2-454-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [1 to 110 / 49 / 1/step]
2-454-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
ENG [1 to 110 / 46 / 1/step]
2-454-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [1 to 110 / 50 / 1/step]
2-454-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [1 to 110 / 46 / 1/step]
2-454-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [1 to 110 / 50 / 1/step]
ENG [1 to 110 / 47 / 1/step] 2-454-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
2-454-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [1 to 110 / 51 / 1/step]
2-454-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [1 to 110 / 47 / 1/step]
2-454-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [1 to 110 / 51 / 1/step]
Engine SP Tables - SP2000-1
2-454-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
2-454-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG
ENG
[1 to 110 / 48 / 1/step]
[1 to 110 / 52 / 1/step]
2-454-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [1 to 110 / 48 / 1/step]
2-454-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [1 to 110 / 52 / 1/step]
2-454-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
ENG [1 to 110 / 48 / 1/step]
2-454-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [1 to 110 / 53 / 1/step]
2-454-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [1 to 110 / 48 / 1/step]
2-454-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [1 to 110 / 53 / 1/step]
2455 [Middle:LeadingEdgeCorrection]
2-455-001 PaperTransfer:Standard:1Side
2-455-002 PaperTransfer:Standard:2Side
2-455-003 Paper Transfer:Low:1side
2-455-004 Paper Transfer:Low:2side
ENG
ENG
ENG
ENG
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
2456 [Middle:SwitchTimingLeadEdge]
2-456-001 PaperTransfer:Standard:1side
2-456-002 PaperTransfer:Standard:2side
2-456-003 Paper Transfer:Low:1side
2-456-004 Paper Transfer:Low:2side
2457 [Middle:TrailEdgeCorrection]
2-457-001 PaperTransfer:Standard:1Side
2-457-002 PaperTransfer:Standard:2Side
2-457-003 Paper Transfer:Low:1side
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
227
228
3. Engine SP Mode Tables
2-457-004 Paper Transfer:Low:2side
2458 [Middle:SwitchTimingTrailEdge]
2-458-001 PaperTransfer:Standard:1side
2-458-002 PaperTransfer:Standard:2side
2-458-003 Paper Transfer:Low:1side
2-458-004 Paper Transfer:Low:2side
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
Engine SP Tables - SP2000-2
2463 [Thin:Bias:BW]
2-463-001 PaperTransfer:Standard:1Sid
2-463-002 PaperTransfer:Standard:2Sid
2-463-003 Paper Transfer:Low:1side
2-463-004 Paper Transfer:Low:2side
2467 [Thin:Bias:FC]
2-467-001 PaperTransfer:Standard:1Sid
2-467-002 PaperTransfer:Standard:2Sid
2-467-003 Paper Transfer:Low:1side
2-467-004 Paper Transfer:Low:2side
2471 [Thin:SizeCorrection:BW]
2-471-001 PaperTransfer:Standard:1Sid:S1
2-471-002 PaperTransfer:Standard:2Sid:S1
2-471-003 PaperTransfer:Low:1Side:S1
2-471-004 PaperTransfer:Low:2Side:S1
2-471-005 PaperTransfer:Standard:1Sid:S2
2-471-006 PaperTransfer:Standard:2Sid:S2
ENG [0 to 200 / 22 / 1-uA/step]
ENG [0 to 200 / 22 / 1-uA/step]
ENG [0 to 200 / 11 / 1-uA/step]
ENG [0 to 200 / 11 / 1-uA/step]
ENG [0 to 200 / 29 / 1-uA/step]
ENG [0 to 200 / 29 / 1-uA/step]
ENG [0 to 200 / 14 / 1-uA/step]
ENG [0 to 200 / 14 / 1-uA/step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
229
230
3. Engine SP Mode Tables
2-471-007 PaperTransfer:Low:1Side:S2
2-471-008 PaperTransfer:Low:2Side:S2
2-471-009 PaperTransfer:Standard:1Sid:S3
2-471-010 PaperTransfer:Standard:2Sid:S3
2-471-011 PaperTransfer:Low:1Side:S3
2-471-012 PaperTransfer:Low:2Side:S3
2-471-013 PaperTransfer:Standard:1Sid:S4
2-471-014 PaperTransfer:Standard:2Sid:S4
2-471-015 PaperTransfer:Low:1Side:S4
2-471-016 PaperTransfer:Low:2Side:S4
2-471-017 PaperTransfer:Standard:1Sid:S5
2-471-018 PaperTransfer:Standard:2Sid:S5
2-471-019 PaperTransfer:Low:1Side:S5
2-471-020 PaperTransfer:Low:2Side:S5
2-471-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
2-471-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 111 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 111 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 121 / 1%/ step]
ENG [100 to 995 / 175 / 1%/ step]
ENG [100 to 995 / 121 / 1%/ step]
ENG [100 to 995 / 175 / 1%/ step]
ENG [100 to 995 / 132 / 1%/ step]
ENG [100 to 995 / 211 / 1%/ step]
ENG [100 to 995 / 132 / 1%/ step]
ENG [100 to 995 / 211 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
Engine SP Tables - SP2000-2
2-471-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-471-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-471-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
2-471-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG
ENG
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 105 / 1%/ step]
2-471-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [100 to 995 / 100 / 1%/ step]
2-471-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [100 to 995 / 105 / 1%/ step]
2-471-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
2-471-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG
ENG
[100 to 995 / 111 / 1%/ step]
[100 to 995 / 140 / 1%/ step]
2-471-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [100 to 995 / 111 / 1%/ step]
2-471-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [100 to 995 / 140 / 1%/ step]
2-471-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
2-471-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG
ENG
[100 to 995 / 121 / 1%/ step]
[100 to 995 / 175 / 1%/ step]
2-471-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [100 to 995 / 121 / 1%/ step]
2-471-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [100 to 995 / 175 / 1%/ step]
2-471-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
2-471-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG
ENG
[100 to 995 / 132 / 1%/ step]
[100 to 995 / 211 / 1%/ step]
231
232
3. Engine SP Mode Tables
2-471-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [100 to 995 / 132 / 1%/ step]
2-471-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [100 to 995 / 211 / 1%/ step]
2472 [Thin:SizeCorrection:FC]
2-472-001 PaperTransfer:Standard:1Sid:S1
2-472-002 PaperTransfer:Standard:1Sid:S1
2-472-003 PaperTransfer:Low:1Side:S1
2-472-004 PaperTransfer:Low:1Side:S1
2-472-005 PaperTransfer:Standard:1Sid:S2
2-472-006 PaperTransfer:Standard:1Sid:S2
2-472-007 PaperTransfer:Low:1Side:S2
2-472-008 PaperTransfer:Low:1Side:S2
2-472-009 PaperTransfer:Standard:1Sid:S3
2-472-010 PaperTransfer:Standard:1Sid:S3
2-472-011 PaperTransfer:Low:1Side:S3
2-472-012 PaperTransfer:Low:1Side:S3
2-472-013 PaperTransfer:Standard:1Sid:S4
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 106 / 1%/ step]
ENG [100 to 995 / 130 / 1%/ step]
ENG [100 to 995 / 106 / 1%/ step]
ENG [100 to 995 / 130 / 1%/ step]
ENG [100 to 995 / 117 / 1%/ step]
ENG [100 to 995 / 153 / 1%/ step]
ENG [100 to 995 / 117 / 1%/ step]
ENG [100 to 995 / 153 / 1%/ step]
ENG [100 to 995 / 128 / 1%/ step]
Engine SP Tables - SP2000-2
2-472-014 PaperTransfer:Standard:1Sid:S4
2-472-015 PaperTransfer:Low:1Side:S4
2-472-016 PaperTransfer:Low:1Side:S4
2-472-017 PaperTransfer:Standard:1Sid:S5
ENG [100 to 995 / 177 / 1%/ step]
ENG [100 to 995 / 128 / 1%/ step]
ENG [100 to 995 / 177 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
2-472-018 PaperTransfer:Standard:2Sid:S5
2-472-019 PaperTransfer:Low:1Side:S5
ENG [100 to 995 / 200 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
2-472-020 PaperTransfer:Low:2Side:S5
2-472-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
2-472-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [100 to 995 / 200 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
2-472-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-472-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-472-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
ENG [100 to 995 / 106 / 1%/ step]
2-472-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [100 to 995 / 130 / 1%/ step]
2-472-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [100 to 995 / 106 / 1%/ step]
2-472-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [100 to 995 / 130 / 1%/ step]
2-472-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
ENG [100 to 995 / 117 / 1%/ step]
233
234
3. Engine SP Mode Tables
2-472-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [100 to 995 / 153 / 1%/ step]
2-472-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [100 to 995 / 117 / 1%/ step]
2-472-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [100 to 995 / 153 / 1%/ step]
2-472-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
ENG [100 to 995 / 128 / 1%/ step]
2-472-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG [100 to 995 / 177 / 1%/ step]
2-472-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [100 to 995 / 128 / 1%/ step]
2-472-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [100 to 995 / 177 / 1%/ step]
2-472-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
ENG [100 to 995 / 140 / 1%/ step]
2-472-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [100 to 995 / 200 / 1%/ step]
2-472-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [100 to 995 / 140 / 1%/ step]
2-472-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [100 to 995 / 200 / 1%/ step]
2473 [Thin:Size-Env.Correct:BW]
2-473-001 PaperTransfer:Standard:1Sid:S1
2-473-002 PaperTransfer:Standard:1Sid:S1
2-473-003 PaperTransfer:Low:1Side:S1
2-473-004 PaperTransfer:Low:1Side:S1
2-473-005 PaperTransfer:Standard:1Sid:S2
2-473-006 PaperTransfer:Standard:1Sid:S2
ENG
ENG
ENG
ENG
ENG
ENG
[1 to 110 / 10 / 1/step]
[1 to 110 / 15 / 1/step]
[1 to 110 / 10 / 1/step]
[1 to 110 / 15 / 1/step]
[1 to 110 / 11 / 1/step]
[1 to 110 / 16 / 1/step]
Engine SP Tables - SP2000-2
2-473-007 PaperTransfer:Low:1Side:S2
2-473-008 PaperTransfer:Low:1Side:S2
2-473-009 PaperTransfer:Standard:1Sid:S3
2-473-010 PaperTransfer:Standard:1Sid:S3
2-473-011 PaperTransfer:Low:1Side:S3
2-473-012 PaperTransfer:Low:1Side:S3
2-473-013 PaperTransfer:Standard:1Sid:S4
ENG [1 to 110 / 11 / 1/step]
ENG [1 to 110 / 16 / 1/step]
ENG [1 to 110 / 12 / 1/step]
ENG [1 to 110 / 30 / 1/step]
ENG [1 to 110 / 12 / 1/step]
ENG [1 to 110 / 30 / 1/step]
ENG [1 to 110 / 13 / 1/step]
2-473-014 PaperTransfer:Standard:1Sid:S4
2-473-015 PaperTransfer:Low:1Side:S4
2-473-016 PaperTransfer:Low:1Side:S4
2-473-017 PaperTransfer:Standard:1Sid:S5
2-473-018 PaperTransfer:Standard:2Sid:S5
2-473-019 PaperTransfer:Low:1Side:S5
2-473-020 PaperTransfer:Low:2Side:S5
2-473-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
2-473-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[1 to 110 / 31 / 1/step]
[1 to 110 / 13 / 1/step]
[1 to 110 / 31 / 1/step]
[1 to 110 / 14 / 1/step]
[1 to 110 / 32 / 1/step]
[1 to 110 / 14 / 1/step]
[1 to 110 / 32 / 1/step]
[1 to 110 / 10 / 1/step]
[1 to 110 / 15 / 1/step]
2-473-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [1 to 110 / 10 / 1/step]
2-473-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [1 to 110 / 15 / 1/step]
ENG [1 to 110 / 11 / 1/step] 2-473-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
2-473-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [1 to 110 / 16 / 1/step]
2-473-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [1 to 110 / 11 / 1/step]
2-473-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [1 to 110 / 16 / 1/step]
2-473-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
ENG [1 to 110 / 12 / 1/step]
235
236
3. Engine SP Mode Tables
2-473-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [1 to 110 / 30 / 1/step]
2-473-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [1 to 110 / 12 / 1/step]
2-473-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [1 to 110 / 30 / 1/step]
2-473-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
ENG [1 to 110 / 13 / 1/step]
2-473-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG [1 to 110 / 31 / 1/step]
2-473-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [1 to 110 / 13 / 1/step]
2-473-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [1 to 110 / 31 / 1/step]
2-473-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
ENG [1 to 110 / 14 / 1/step]
2-473-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [1 to 110 / 32 / 1/step]
2-473-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [1 to 110 / 14 / 1/step]
2-473-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [1 to 110 / 32 / 1/step]
2474 [Thin:Size-Env.Correct:FC]
2-474-001 PaperTransfer:Standard:1Sid:S1
2-474-002 PaperTransfer:Standard:1Sid:S1
2-474-003 PaperTransfer:Low:1Side:S1
2-474-004 PaperTransfer:Low:1Side:S1
2-474-005 PaperTransfer:Standard:1Sid:S2
2-474-006 PaperTransfer:Standard:1Sid:S2
2-474-007 PaperTransfer:Low:1Side:S2
2-474-008 PaperTransfer:Low:1Side:S2
2-474-009 PaperTransfer:Standard:1Sid:S3
2-474-010 PaperTransfer:Standard:1Sid:S3
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[1 to 110 / 20 / 1/step]
[1 to 110 / 25 / 1/step]
[1 to 110 / 20 / 1/step]
[1 to 110 / 25 / 1/step]
[1 to 110 / 21 / 1/step]
[1 to 110 / 35 / 1/step]
[1 to 110 / 21 / 1/step]
ENG [1 to 110 / 35 / 1/step]
ENG [1 to 110 / 33 / 1/step]
ENG [1 to 110 / 36 / 1/step]
Engine SP Tables - SP2000-2
2-474-011 PaperTransfer:Low:1Side:S3
2-474-012 PaperTransfer:Low:1Side:S3
2-474-013 PaperTransfer:Standard:1Sid:S4
2-474-014 PaperTransfer:Standard:1Sid:S4
2-474-015 PaperTransfer:Low:1Side:S4
2-474-016 PaperTransfer:Low:1Side:S4
2-474-017 PaperTransfer:Standard:1Sid:S5
ENG [1 to 110 / 33 / 1/step]
ENG [1 to 110 / 36 / 1/step]
ENG [1 to 110 / 34 / 1/step]
ENG [1 to 110 / 37 / 1/step]
ENG [1 to 110 / 34 / 1/step]
ENG [1 to 110 / 37 / 1/step]
ENG [1 to 110 / 24 / 1/step]
2-474-018 PaperTransfer:Standard:2Sid:S5
2-474-019 PaperTransfer:Low:1Side:S5
ENG
ENG
[1 to 110 / 38 / 1/step]
[1 to 110 / 24 / 1/step]
2-474-020 PaperTransfer:Low:2Side:S5
2-474-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
ENG
ENG
[1 to 110 / 38 / 1/step]
[1 to 110 / 20 / 1/step]
2-474-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [1 to 110 / 25 / 1/step]
2-474-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [1 to 110 / 20 / 1/step]
2-474-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [1 to 110 / 25 / 1/step]
2-474-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
ENG [1 to 110 / 21 / 1/step]
2-474-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [1 to 110 / 35 / 1/step]
2-474-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [1 to 110 / 21 / 1/step]
2-474-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [1 to 110 / 35 / 1/step]
ENG [1 to 110 / 33 / 1/step] 2-474-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
2-474-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [1 to 110 / 36 / 1/step]
2-474-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [1 to 110 / 33 / 1/step]
2-474-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [1 to 110 / 36 / 1/step]
237
238
3. Engine SP Mode Tables
2-474-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
2-474-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG
ENG
[1 to 110 / 34 / 1/step]
[1 to 110 / 37 / 1/step]
2-474-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [1 to 110 / 34 / 1/step]
2-474-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [1 to 110 / 37 / 1/step]
2-474-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
ENG [1 to 110 / 24 / 1/step]
2-474-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [1 to 110 / 38 / 1/step]
2-474-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [1 to 110 / 24 / 1/step]
2-474-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [1 to 110 / 38 / 1/step]
2475 [Thin:LeadingEdgeCorrection]
2-475-001 PaperTransfer:Standard:1Side
2-475-002 PaperTransfer:Standard:2Side
2-475-003 Paper Transfer:Low:1side
2-475-004 Paper Transfer:Low:2side
ENG
ENG
ENG
ENG
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
2476 [Thin:SwitchTimingLeadEdge]
2-476-001 PaperTransfer:Standard:1side
2-476-002 PaperTransfer:Standard:2side
2-476-003 Paper Transfer:Low:1side
2-476-004 Paper Transfer:Low:2side
2477 [Thin:TrailEdgeCorrection]
2-477-001 PaperTransfer:Standard:1Side
2-477-002 PaperTransfer:Standard:2Side
2-477-003 Paper Transfer:Low:1side
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
2-477-004 Paper Transfer:Low:2side
2478 [Thin:SwitchTimingTrailEdge]
2-478-001 PaperTransfer:Standard:1side
2-478-002 PaperTransfer:Standard:2side
2-478-003 Paper Transfer:Low:1side
2-478-004 Paper Transfer:Low:2side
2483 [Thick1:Bias:BW]
2-483-001 PaperTransfer:middle:1side
2-483-002 PaperTransfer:middle:2side
2-483-003 PaperTransfer:low:1side
2-483-004 PaperTransfer:low:2side
2487 [Thick1:Bias:FC]
2-487-001 PaperTransfer:middle:1side
2-487-002 PaperTransfer:middle:2side
2-487-003 PaperTransfer:low:1side
2-487-004 PaperTransfer:low:2side
2491 [Thick1:SizeCorrection:BW]
2-491-001 PaperTransfer:middle:1Sid:S1
2-491-002 PaperTransfer:middle:1Sid:S1
2-491-003 PaperTransfer:Low:1Side:S1
2-491-004 PaperTransfer:Low:1Side:S1
Engine SP Tables - SP2000-2
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 200 / 16 / 1-uA/step]
ENG [0 to 200 / 13 / 1-uA/step]
ENG [0 to 200 / 11 / 1-uA/step]
ENG [0 to 200 / 9 / 1-uA/step]
ENG [0 to 200 / 23 / 1-uA/step]
ENG [0 to 200 / 26 / 1-uA/step]
ENG [0 to 200 / 16 / 1-uA/step]
ENG [0 to 200 / 18 / 1-uA/step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
239
240
3. Engine SP Mode Tables
2-491-005 PaperTransfer:middle:1Sid:S2
2-491-006 PaperTransfer:middle:1Sid:S2
2-491-007 PaperTransfer:Low:1Side:S2
2-491-008 PaperTransfer:Low:1Side:S2
2-491-009 PaperTransfer:middle:1Sid:S3
2-491-010 PaperTransfer:middle:1Sid:S3
2-491-011 PaperTransfer:Low:1Side:S3
2-491-012 PaperTransfer:Low:1Side:S3
2-491-013 PaperTransfer:middle:1Sid:S4
2-491-014 PaperTransfer:middle:1Sid:S4
2-491-015 PaperTransfer:Low:1Side:S4
2-491-016 PaperTransfer:Low:1Side:S4
2-491-017 PaperTransfer:middle:1Sid:S5
2-491-018 PaperTransfer:middle:2Sid:S5
2-491-019 PaperTransfer:Low:1Side:S5
2-491-020 PaperTransfer:Low:2Side:S5
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 177 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 177 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 231 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 231 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 270 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 270 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 308 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 308 / 1%/ step]
Engine SP Tables - SP2000-2
2-491-021 Wide Roller:PaperTransfer:middle:
1Sid:S1
2-491-022 Wide Roller:PaperTransfer:middle:
2Sid:S1
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
2-491-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-491-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-491-025 Wide Roller:PaperTransfer:middle:
1Sid:S2
2-491-026 Wide Roller:PaperTransfer:middle:
2Sid:S2
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 177 / 1%/ step]
2-491-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [100 to 995 / 100 / 1%/ step]
2-491-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [100 to 995 / 177 / 1%/ step]
2-491-029 Wide Roller:PaperTransfer:middle:
1Sid:S3
2-491-030 Wide Roller:PaperTransfer:middle:
2Sid:S3
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 231 / 1%/ step]
2-491-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [100 to 995 / 100 / 1%/ step]
2-491-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [100 to 995 / 231 / 1%/ step]
2-491-033 Wide Roller:PaperTransfer:middle:
1Sid:S4
2-491-034 Wide Roller:PaperTransfer:middle:
2Sid:S4
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 270 / 1%/ step]
2-491-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [100 to 995 / 100 / 1%/ step]
2-491-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [100 to 995 / 270 / 1%/ step]
241
242
3. Engine SP Mode Tables
2-491-037 Wide Roller:PaperTransfer:middle:
1Sid:S5
2-491-038 Wide Roller:PaperTransfer:middle:
2Sid:S5
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 308 / 1%/ step]
2-491-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [100 to 995 / 100 / 1%/ step]
2-491-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [100 to 995 / 308 / 1%/ step]
2492 [Thick1:SizeCorrection:FC]
2-492-001 PaperTransfer:middle:1Sid:S1
2-492-002 PaperTransfer:middle:1Sid:S1
2-492-003 PaperTransfer:Low:1Side:S1
2-492-004 PaperTransfer:Low:1Side:S1
2-492-005 PaperTransfer:middle:1Sid:S2
2-492-006 PaperTransfer:middle:1Sid:S2
2-492-007 PaperTransfer:Low:1Side:S2
2-492-008 PaperTransfer:Low:1Side:S2
2-492-009 PaperTransfer:middle:1Sid:S3
2-492-010 PaperTransfer:middle:1Sid:S3
2-492-011 PaperTransfer:Low:1Side:S3
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 173 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 173 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 250 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
Engine SP Tables - SP2000-2
2-492-012 PaperTransfer:Low:1Side:S3
2-492-013 PaperTransfer:middle:1Sid:S4
2-492-014 PaperTransfer:middle:1Sid:S4
2-492-015 PaperTransfer:Low:1Side:S4
2-492-016 PaperTransfer:Low:1Side:S4
2-492-017 PaperTransfer:middle:1Sid:S5
2-492-018 PaperTransfer:middle:2Sid:S5
2-492-019 PaperTransfer:Low:1Side:S5
ENG [100 to 995 / 250 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 308 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 308 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 385 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
2-492-020 PaperTransfer:Low:2Side:S5
2-492-021 Wide Roller:PaperTransfer:middle:
1Sid:S1
2-492-022 Wide Roller:PaperTransfer:middle:
2Sid:S1
ENG [100 to 995 / 385 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
2-492-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-492-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-492-025 Wide Roller:PaperTransfer:middle:
1Sid:S2
ENG [100 to 995 / 100 / 1%/ step]
2-492-026 Wide Roller:PaperTransfer:middle:
2Sid:S2
ENG [100 to 995 / 173 / 1%/ step]
2-492-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [100 to 995 / 100 / 1%/ step]
243
244
3. Engine SP Mode Tables
2-492-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [100 to 995 / 173 / 1%/ step]
2-492-029 Wide Roller:PaperTransfer:middle:
1Sid:S3
ENG [100 to 995 / 100 / 1%/ step]
2-492-030 Wide Roller:PaperTransfer:middle:
2Sid:S3
ENG [100 to 995 / 250 / 1%/ step]
2-492-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [100 to 995 / 100 / 1%/ step]
2-492-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [100 to 995 / 250 / 1%/ step]
2-492-033 Wide Roller:PaperTransfer:middle:
1Sid:S4
ENG [100 to 995 / 100 / 1%/ step]
2-492-034 Wide Roller:PaperTransfer:middle:
2Sid:S4
ENG [100 to 995 / 308 / 1%/ step]
2-492-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [100 to 995 / 100 / 1%/ step]
2-492-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [100 to 995 / 308 / 1%/ step]
2-492-037 Wide Roller:PaperTransfer:middle:
1Sid:S5
ENG [100 to 995 / 100 / 1%/ step]
2-492-038 Wide Roller:PaperTransfer:middle:
2Sid:S5
ENG [100 to 995 / 385 / 1%/ step]
2-492-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [100 to 995 / 100 / 1%/ step]
2-492-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG
[100 to 995 / 385 / 1%/ step]
2493 [Thick1:Size-Env.Correct:BW]
2-493-001 PaperTransfer:middle:1Sid:S1
2-493-002 PaperTransfer:middle:1Sid:S1
2-493-003 PaperTransfer:Low:1Side:S1
ENG
ENG
ENG
[1 to 110 / 54 / 1/step]
[1 to 110 / 57 / 1/step]
[1 to 110 / 54 / 1/step]
Engine SP Tables - SP2000-2
2-493-004 PaperTransfer:Low:1Side:S1
2-493-005 PaperTransfer:middle:1Sid:S2
2-493-006 PaperTransfer:middle:1Sid:S2
2-493-007 PaperTransfer:Low:1Side:S2
2-493-008 PaperTransfer:Low:1Side:S2
2-493-009 PaperTransfer:middle:1Sid:S3
2-493-010 PaperTransfer:middle:1Sid:S3
2-493-011 PaperTransfer:Low:1Side:S3
2-493-012 PaperTransfer:Low:1Side:S3
2-493-013 PaperTransfer:middle:1Sid:S4
2-493-014 PaperTransfer:middle:1Sid:S4
2-493-015 PaperTransfer:Low:1Side:S4
2-493-016 PaperTransfer:Low:1Side:S4
2-493-017 PaperTransfer:middle:1Sid:S5
2-493-018 PaperTransfer:middle:2Sid:S5
ENG
ENG [1 to 110 / 55 / 1/step]
ENG [1 to 110 / 58 / 1/step]
ENG [1 to 110 / 55 / 1/step]
ENG [1 to 110 / 58 / 1/step]
ENG [1 to 110 / 56 / 1/step]
ENG [1 to 110 / 59 / 1/step]
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[1 to 110 / 57 / 1/step]
[1 to 110 / 56 / 1/step]
[1 to 110 / 59 / 1/step]
[1 to 110 / 56 / 1/step]
[1 to 110 / 60 / 1/step]
[1 to 110 / 56 / 1/step]
[1 to 110 / 60 / 1/step]
[1 to 110 / 56 / 1/step]
[1 to 110 / 61 / 1/step]
2-493-019 PaperTransfer:Low:1Side:S5
2-493-020 PaperTransfer:Low:2Side:S5
ENG [1 to 110 / 56 / 1/step]
ENG [1 to 110 / 61 / 1/step]
2-493-021 Wide Roller:PaperTransfer:middle:
1Sid:S1
2-493-022 Wide Roller:PaperTransfer:middle:
2Sid:S1
ENG
ENG
[1 to 110 / 54 / 1/step]
[1 to 110 / 57 / 1/step]
2-493-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [1 to 110 / 54 / 1/step]
2-493-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [1 to 110 / 57 / 1/step]
2-493-025 Wide Roller:PaperTransfer:middle:
1Sid:S2
ENG [1 to 110 / 55 / 1/step]
2-493-026 Wide Roller:PaperTransfer:middle:
2Sid:S2
ENG [1 to 110 / 58 / 1/step]
245
246
3. Engine SP Mode Tables
2-493-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [1 to 110 / 55 / 1/step]
2-493-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [1 to 110 / 58 / 1/step]
2-493-029 Wide Roller:PaperTransfer:middle:
1Sid:S3
ENG [1 to 110 / 56 / 1/step]
2-493-030 Wide Roller:PaperTransfer:middle:
2Sid:S3
ENG [1 to 110 / 59 / 1/step]
2-493-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [1 to 110 / 56 / 1/step]
2-493-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [1 to 110 / 59 / 1/step]
2-493-033 Wide Roller:PaperTransfer:middle:
1Sid:S4
ENG [1 to 110 / 56 / 1/step]
2-493-034 Wide Roller:PaperTransfer:middle:
2Sid:S4
ENG [1 to 110 / 60 / 1/step]
2-493-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [1 to 110 / 56 / 1/step]
2-493-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [1 to 110 / 60 / 1/step]
2-493-037 Wide Roller:PaperTransfer:middle:
1Sid:S5
ENG [1 to 110 / 56 / 1/step]
2-493-038 Wide Roller:PaperTransfer:middle:
2Sid:S5
ENG [1 to 110 / 61 / 1/step]
2-493-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [1 to 110 / 56 / 1/step]
2-493-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [1 to 110 / 61 / 1/step]
2494 [Thick1:Size-Env.Correct:FC]
2-494-001 PaperTransfer:middle:1Sid:S1
2-494-002 PaperTransfer:middle:1Sid:S1
2-494-003 PaperTransfer:Low:1Side:S1
2-494-004 PaperTransfer:Low:1Side:S1
2-494-005 PaperTransfer:middle:1Sid:S2
2-494-006 PaperTransfer:middle:1Sid:S2
ENG [1 to 110 / 13 / 1/step]
ENG [1 to 110 / 65 / 1/step]
ENG [1 to 110 / 13 / 1/step]
ENG [1 to 110 / 65 / 1/step]
ENG [1 to 110 / 63 / 1/step]
ENG [1 to 110 / 66 / 1/step]
Engine SP Tables - SP2000-2
2-494-007 PaperTransfer:Low:1Side:S2
2-494-008 PaperTransfer:Low:1Side:S2
2-494-009 PaperTransfer:middle:1Sid:S3
2-494-010 PaperTransfer:middle:1Sid:S3
2-494-011 PaperTransfer:Low:1Side:S3
2-494-012 PaperTransfer:Low:1Side:S3
2-494-013 PaperTransfer:middle:1Sid:S4
ENG [1 to 110 / 63 / 1/step]
ENG [1 to 110 / 66 / 1/step]
ENG [1 to 110 / 63 / 1/step]
ENG [1 to 110 / 67 / 1/step]
ENG [1 to 110 / 63 / 1/step]
ENG [1 to 110 / 67 / 1/step]
ENG [1 to 110 / 64 / 1/step]
2-494-014 PaperTransfer:middle:1Sid:S4
2-494-015 PaperTransfer:Low:1Side:S4
2-494-016 PaperTransfer:Low:1Side:S4
2-494-017 PaperTransfer:middle:1Sid:S5
2-494-018 PaperTransfer:middle:2Sid:S5
2-494-019 PaperTransfer:Low:1Side:S5
2-494-020 PaperTransfer:Low:2Side:S5
2-494-021 Wide Roller:PaperTransfer:middle:
1Sid:S1
2-494-022 Wide Roller:PaperTransfer:middle:
2Sid:S1
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[1 to 110 / 68 / 1/step]
[1 to 110 / 64 / 1/step]
[1 to 110 / 68 / 1/step]
[1 to 110 / 64 / 1/step]
[1 to 110 / 69 / 1/step]
[1 to 110 / 64 / 1/step]
[1 to 110 / 69 / 1/step]
[1 to 110 / 13 / 1/step]
[1 to 110 / 65 / 1/step]
2-494-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [1 to 110 / 13 / 1/step]
2-494-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [1 to 110 / 65 / 1/step]
ENG [1 to 110 / 63 / 1/step] 2-494-025 Wide Roller:PaperTransfer:middle:
1Sid:S2
2-494-026 Wide Roller:PaperTransfer:middle:
2Sid:S2
ENG [1 to 110 / 66 / 1/step]
2-494-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [1 to 110 / 63 / 1/step]
2-494-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [1 to 110 / 66 / 1/step]
2-494-029 Wide Roller:PaperTransfer:middle:
1Sid:S3
ENG [1 to 110 / 63 / 1/step]
247
248
3. Engine SP Mode Tables
2-494-030 Wide Roller:PaperTransfer:middle:
2Sid:S3
ENG [1 to 110 / 67 / 1/step]
2-494-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [1 to 110 / 63 / 1/step]
2-494-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [1 to 110 / 67 / 1/step]
2-494-033 Wide Roller:PaperTransfer:middle:
1Sid:S4
ENG [1 to 110 / 64 / 1/step]
2-494-034 Wide Roller:PaperTransfer:middle:
2Sid:S4
ENG [1 to 110 / 68 / 1/step]
2-494-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [1 to 110 / 64 / 1/step]
2-494-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [1 to 110 / 68 / 1/step]
2-494-037 Wide Roller:PaperTransfer:middle:
1Sid:S5
ENG [1 to 110 / 64 / 1/step]
2-494-038 Wide Roller:PaperTransfer:middle:
2Sid:S5
ENG [1 to 110 / 69 / 1/step]
2-494-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [1 to 110 / 64 / 1/step]
2-494-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [1 to 110 / 69 / 1/step]
2495 [Thick1:LeadingEdgeCorrection]
2-495-001 PaperTransfer:middle:1Side
2-495-002 PaperTransfer:middle:2Side
2-495-003 Paper Transfer:Low:1side
2-495-004 Paper Transfer:Low:2side
ENG
ENG
ENG
ENG
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
2496 [Thick1:SwitchTimingLeadEdge]
2-496-001 PaperTransfer:middle:1side
2-496-002 PaperTransfer:middle:2side
2-496-003 Paper Transfer:Low:1side
2-496-004 Paper Transfer:Low:2side
ENG
ENG
ENG
ENG
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
Engine SP Tables - SP2000-2
2497 [Thick1:TrailEdgeCorrection]
2-497-001 PaperTransfer:middle:1Side
2-497-002 PaperTransfer:middle:2Side
2-497-003 Paper Transfer:Low:1side
2-497-004 Paper Transfer:Low:2side
2498 [Thick1:SwitchTimingTrailEdge]
2-498-001 PaperTransfer:middle:1Side
2-498-002 PaperTransfer:middle:2Side
2-498-003 Paper Transfer:Low:1side
2-498-004 Paper Transfer:Low:2side
2503 [Thick2:Bias:BW]
2-503-003 PaperTransfer:1side
2-503-004 PaperTransfer:2side
2507 [Thick2:Bias:FC]
2-507-003 PaperTransfer:1side
2-507-004 PaperTransfer:2side
2511 [Thick2:SizeCorrection:BW]
2-511-003 PaperTransfer:1Side:S1
2-511-004 PaperTransfer:2Side:S1
2-511-007 PaperTransfer:1Side:S2
2-511-008 PaperTransfer:2Side:S2
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 200 / 11 / 1-uA/step]
ENG [0 to 200 / 15 / 1-uA/step]
ENG [0 to 200 / 19 / 1-uA/step]
ENG [0 to 200 / 21 / 1-uA/step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 133 / 1%/ step]
249
250
3. Engine SP Mode Tables
2-511-011 PaperTransfer:1Side:S3
2-511-012 PaperTransfer:2Side:S3
2-511-015 PaperTransfer:1Side:S4
2-511-016 PaperTransfer:2Side:S4
2-511-019 PaperTransfer:1Side:S5
2-511-020 PaperTransfer:2Side:S5
2-511-023 Wide Roller:PaperTransfer:1Side:S1
2-511-024 Wide Roller:PaperTransfer:2Side:S1
2-511-027 Wide Roller:PaperTransfer:1Side:S2
2-511-028 Wide Roller:PaperTransfer:2Side:S2
2-511-031 Wide Roller:PaperTransfer:1Side:S3
2-511-032 Wide Roller:PaperTransfer:2Side:S3
2-511-035 Wide Roller:PaperTransfer:1Side:S4
2-511-036 Wide Roller:PaperTransfer:2Side:S4
2-511-039 Wide Roller:PaperTransfer:1Side:S5
2-511-040
Wide Roller:PaperTransfer:2Side:S5
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 167 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 233 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 267 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 133 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 167 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 233 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG
[100 to 995 / 267 / 1%/ step]
Engine SP Tables - SP2000-2
2512 [Thick2:SizeCorrection:FC]
2-512-003 PaperTransfer:1Side:S1
2-512-004 PaperTransfer:2Side:S1
2-512-007 PaperTransfer:1Side:S2
2-512-008 PaperTransfer:2Side:S2
2-512-011 PaperTransfer:1Side:S3
2-512-012 PaperTransfer:2Side:S3
2-512-015 PaperTransfer:1Side:S4
2-512-016 PaperTransfer:2Side:S4
2-512-019 PaperTransfer:1Side:S5
2-512-020 PaperTransfer:2Side:S5
2-512-023 Wide Roller:PaperTransfer:1Side:S1
2-512-024 Wide Roller:PaperTransfer:2Side:S1
2-512-027 Wide Roller:PaperTransfer:1Side:S2
2-512-028 Wide Roller:PaperTransfer:2Side:S2
2-512-031 Wide Roller:PaperTransfer:1Side:S3
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 181 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 229 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 286 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 381 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 181 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
251
252
3. Engine SP Mode Tables
2-512-032 Wide Roller:PaperTransfer:2Side:S3
2-512-035 Wide Roller:PaperTransfer:1Side:S4
2-512-036 Wide Roller:PaperTransfer:2Side:S4
2-512-039 Wide Roller:PaperTransfer:1Side:S5
2-512-040
Wide Roller:PaperTransfer:2Side:S5
2513 [Thick2:Size-Env.Correct:BW]
2-513-003 PaperTransfer:1Side:S1
2-513-004 PaperTransfer:2Side:S1
2-513-007 PaperTransfer:1Side:S2
2-513-008 PaperTransfer:2Side:S2
2-513-011 PaperTransfer:1Side:S3
2-513-012 PaperTransfer:2Side:S3
2-513-015 PaperTransfer:1Side:S4
2-513-016 PaperTransfer:2Side:S4
2-513-019 PaperTransfer:1Side:S5
2-513-020 PaperTransfer:2Side:S5
2-513-023 Wide Roller:PaperTransfer:1Side:S1
2-513-024 Wide Roller:PaperTransfer:2Side:S1
2-513-027 Wide Roller:PaperTransfer:1Side:S2
2-513-028 Wide Roller:PaperTransfer:2Side:S2
2-513-031 Wide Roller:PaperTransfer:1Side:S3
2-513-032 Wide Roller:PaperTransfer:2Side:S3
ENG [100 to 995 / 229 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 286 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG
[100 to 995 / 381 / 1%/ step]
ENG [1 to 110 / 70 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 71 / 1/step]
ENG [1 to 110 / 73 / 1/step]
ENG [1 to 110 / 71 / 1/step]
ENG [1 to 110 / 74 / 1/step]
ENG [1 to 110 / 71 / 1/step]
ENG [1 to 110 / 75 / 1/step]
ENG [1 to 110 / 71 / 1/step]
ENG [1 to 110 / 76 / 1/step]
ENG [1 to 110 / 70 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 71 / 1/step]
ENG [1 to 110 / 73 / 1/step]
ENG [1 to 110 / 71 / 1/step]
ENG [1 to 110 / 74 / 1/step]
Engine SP Tables - SP2000-2
2-513-035 Wide Roller:PaperTransfer:1Side:S4
2-513-036 Wide Roller:PaperTransfer:2Side:S4
2-513-039 Wide Roller:PaperTransfer:1Side:S5
2-513-040 Wide Roller:PaperTransfer:2Side:S5
2514 [Thick2:Size-Env.Correct:FC]
2-514-003 PaperTransfer:1Side:S1
2-514-004 PaperTransfer:2Side:S1
2-514-007 PaperTransfer:1Side:S2
2-514-008 PaperTransfer:2Side:S2
2-514-011 PaperTransfer:1Side:S3
2-514-012 PaperTransfer:2Side:S3
2-514-015 PaperTransfer:1Side:S4
2-514-016 PaperTransfer:2Side:S4
2-514-019 PaperTransfer:1Side:S5
2-514-020 PaperTransfer:2Side:S5
2-514-023 Wide Roller:PaperTransfer:1Side:S1
2-514-024 Wide Roller:PaperTransfer:2Side:S1
2-514-027 Wide Roller:PaperTransfer:1Side:S2
2-514-028 Wide Roller:PaperTransfer:2Side:S2
2-514-031 Wide Roller:PaperTransfer:1Side:S3
2-514-032 Wide Roller:PaperTransfer:2Side:S3
2-514-035 Wide Roller:PaperTransfer:1Side:S4
2-514-036 Wide Roller:PaperTransfer:2Side:S4
2-514-039 Wide Roller:PaperTransfer:1Side:S5
2-514-040 Wide Roller:PaperTransfer:2Side:S5
ENG [1 to 110 / 71 / 1/step]
ENG [1 to 110 / 75 / 1/step]
ENG [1 to 110 / 71 / 1/step]
ENG [1 to 110 / 76 / 1/step]
ENG [1 to 110 / 77 / 1/step]
ENG [1 to 110 / 80 / 1/step]
ENG [1 to 110 / 78 / 1/step]
ENG [1 to 110 / 81 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 82 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 83 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 84 / 1/step]
ENG [1 to 110 / 77 / 1/step]
ENG [1 to 110 / 80 / 1/step]
ENG [1 to 110 / 78 / 1/step]
ENG [1 to 110 / 81 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 82 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 83 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 84 / 1/step]
253
254
3. Engine SP Mode Tables
2515 [Thick2:LeadingEdgeCorrection]
2-515-003 Paper Transfer:1side
2-515-004 Paper Transfer:2side
2516 [Thick2:SwitchTimingLeadEdge]
2-516-003 Paper Transfer:1side
2-516-004 Paper Transfer:2side
2517 [Thick2:TrailEdgeCorrection]
2-517-003 Paper Transfer:1side
2-517-004 Paper Transfer:2side
2518 [Thick2:SwitchTimingTrailEdge]
2-518-003 Paper Transfer:1side
2-518-004 Paper Transfer:2side
2523 [Thick3:Bias:BW]
2-523-003 PaperTransfer:1side
2-523-004 PaperTransfer:2side
2527 [Thick3:Bias:FC]
2-527-003 PaperTransfer:1side
2-527-004 PaperTransfer:2side
2531 [Thick3:SizeCorrection:BW]
2-531-003 PaperTransfer:1Side:S1
2-531-004 PaperTransfer:2Side:S1
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 200 / 11 / 1-uA/step]
ENG [0 to 200 / 15 / 1-uA/step]
ENG [0 to 200 / 19 / 1-uA/step]
ENG [0 to 200 / 21 / 1-uA/step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
Engine SP Tables - SP2000-2
2-531-007 PaperTransfer:1Side:S2
2-531-008 PaperTransfer:2Side:S2
2-531-011 PaperTransfer:1Side:S3
2-531-012 PaperTransfer:2Side:S3
2-531-015 PaperTransfer:1Side:S4
2-531-016 PaperTransfer:2Side:S4
2-531-019 PaperTransfer:1Side:S5
2-531-020 PaperTransfer:2Side:S5
2-531-023 Wide Roller:PaperTransfer:1Side:S1
2-531-024 Wide Roller:PaperTransfer:2Side:S1
2-531-027 Wide Roller:PaperTransfer:1Side:S2
2-531-028 Wide Roller:PaperTransfer:2Side:S2
2-531-031 Wide Roller:PaperTransfer:1Side:S3
2-531-032 Wide Roller:PaperTransfer:2Side:S3
2-531-035 Wide Roller:PaperTransfer:1Side:S4
2-531-036 Wide Roller:PaperTransfer:2Side:S4
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 133 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 167 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 233 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 267 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 133 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 167 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 233 / 1%/ step]
255
256
3. Engine SP Mode Tables
2-531-039 Wide Roller:PaperTransfer:1Side:S5
2-531-040 Wide Roller:PaperTransfer:2Side:S5
2532 [Thick3:SizeCorrection:FC]
2-532-003 PaperTransfer:1Side:S1
2-532-004 PaperTransfer:2Side:S1
2-532-007 PaperTransfer:1Side:S2
2-532-008 PaperTransfer:2Side:S2
2-532-011 PaperTransfer:1Side:S3
2-532-012 PaperTransfer:2Side:S3
2-532-015 PaperTransfer:1Side:S4
2-532-016 PaperTransfer:2Side:S4
2-532-019 PaperTransfer:1Side:S5
2-532-020 PaperTransfer:2Side:S5
2-532-023 Wide Roller:PaperTransfer:1Side:S1
2-532-024 Wide Roller:PaperTransfer:2Side:S1
2-532-027 Wide Roller:PaperTransfer:1Side:S2
ENG [100 to 995 / 100 / 1%/ step]
ENG
[100 to 995 / 267 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 181 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 229 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 286 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 381 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
Engine SP Tables - SP2000-2
2-532-028 Wide Roller:PaperTransfer:2Side:S2
2-532-031 Wide Roller:PaperTransfer:1Side:S3
2-532-032 Wide Roller:PaperTransfer:2Side:S3
2-532-035 Wide Roller:PaperTransfer:1Side:S4
2-532-036 Wide Roller:PaperTransfer:2Side:S4
2-532-039 Wide Roller:PaperTransfer:1Side:S5
2-532-040 Wide Roller:PaperTransfer:2Side:S5
2533 [Thick3:Size-Env.Correct:BW]
2-533-003 PaperTransfer:1Side:S1
2-533-004 PaperTransfer:2Side:S1
2-533-007 PaperTransfer:1Side:S2
2-533-008 PaperTransfer:2Side:S2
2-533-011 PaperTransfer:1Side:S3
2-533-012 PaperTransfer:2Side:S3
2-533-015 PaperTransfer:1Side:S4
2-533-016 PaperTransfer:2Side:S4
2-533-019 PaperTransfer:1Side:S5
2-533-020 PaperTransfer:2Side:S5
2-533-023 Wide Roller:PaperTransfer:1Side:S1
2-533-024 Wide Roller:PaperTransfer:2Side:S1
2-533-027 Wide Roller:PaperTransfer:1Side:S2
ENG [100 to 995 / 181 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 229 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 286 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG
[100 to 995 / 381 / 1%/ step]
ENG [1 to 110 / 85 / 1/step]
ENG [1 to 110 / 87 / 1/step]
ENG [1 to 110 / 86 / 1/step]
ENG [1 to 110 / 88 / 1/step]
ENG [1 to 110 / 86 / 1/step]
ENG [1 to 110 / 89 / 1/step]
ENG [1 to 110 / 86 / 1/step]
ENG [1 to 110 / 90 / 1/step]
ENG [1 to 110 / 86 / 1/step]
ENG [1 to 110 / 91 / 1/step]
ENG [1 to 110 / 85 / 1/step]
ENG [1 to 110 / 87 / 1/step]
ENG [1 to 110 / 86 / 1/step]
257
258
3. Engine SP Mode Tables
2-533-028 Wide Roller:PaperTransfer:2Side:S2
2-533-031 Wide Roller:PaperTransfer:1Side:S3
2-533-032 Wide Roller:PaperTransfer:2Side:S3
2-533-035 Wide Roller:PaperTransfer:1Side:S4
2-533-036 Wide Roller:PaperTransfer:2Side:S4
2-533-039 Wide Roller:PaperTransfer:1Side:S5
2-533-040 Wide Roller:PaperTransfer:2Side:S5
2534 [Thick3:Size-Env.Correct:FC]
2-534-003 PaperTransfer:1Side:S1
2-534-004 PaperTransfer:2Side:S1
2-534-007 PaperTransfer:1Side:S2
2-534-008 PaperTransfer:2Side:S2
2-534-011 PaperTransfer:1Side:S3
2-534-012 PaperTransfer:2Side:S3
2-534-015 PaperTransfer:1Side:S4
2-534-016 PaperTransfer:2Side:S4
2-534-019 PaperTransfer:1Side:S5
2-534-020 PaperTransfer:2Side:S5
2-534-023 Wide Roller:PaperTransfer:1Side:S1
2-534-024 Wide Roller:PaperTransfer:2Side:S1
2-534-027 Wide Roller:PaperTransfer:1Side:S2
2-534-028 Wide Roller:PaperTransfer:2Side:S2
2-534-031 Wide Roller:PaperTransfer:1Side:S3
2-534-032 Wide Roller:PaperTransfer:2Side:S3
2-534-035 Wide Roller:PaperTransfer:1Side:S4
ENG [1 to 110 / 88 / 1/step]
ENG [1 to 110 / 86 / 1/step]
ENG [1 to 110 / 89 / 1/step]
ENG [1 to 110 / 86 / 1/step]
ENG [1 to 110 / 90 / 1/step]
ENG [1 to 110 / 86 / 1/step]
ENG [1 to 110 / 91 / 1/step]
ENG [1 to 110 / 77 / 1/step]
ENG [1 to 110 / 92 / 1/step]
ENG [1 to 110 / 78 / 1/step]
ENG [1 to 110 / 93 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 94 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 95 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 96 / 1/step]
ENG [1 to 110 / 77 / 1/step]
ENG [1 to 110 / 92 / 1/step]
ENG [1 to 110 / 78 / 1/step]
ENG [1 to 110 / 93 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 94 / 1/step]
ENG [1 to 110 / 79 / 1/step]
Engine SP Tables - SP2000-2
2-534-036 Wide Roller:PaperTransfer:2Side:S4
2-534-039 Wide Roller:PaperTransfer:1Side:S5
2-534-040 Wide Roller:PaperTransfer:2Side:S5
2535 [Thick3:LeadingEdgeCorrection]
2-535-003 Paper Transfer:1side
2-535-004 Paper Transfer:2side
2536 [Thick3:SwitchTimingLeadEdge]
2-536-003 Paper Transfer:1side
2-536-004 Paper Transfer:2side
2537 [Thick3:TrailEdgeCorrection]
2-537-003 Paper Transfer:1side
2-537-004 Paper Transfer:2side
2538 [Thick3:SwitchTimingTrailEdge]
2-538-003 Paper Transfer:1side
2-538-004 Paper Transfer:2side
2543 [OHP:Bias:BW]
2-543-003 PaperTransfer
2547 [OHP:Bias:FC]
2-547-003 PaperTransfer
2551 [OHP:SizeCorrection:BW]
2-551-003 PaperTransfer:S1
ENG [1 to 110 / 95 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 96 / 1/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 200 / 11 / 1-uA/step]
ENG [0 to 200 / 19 / 1-uA/step]
ENG
[100 to 995 / 100 / 1%/ step]
259
260
3. Engine SP Mode Tables
2-551-007 PaperTransfer:S2
2-551-011 PaperTransfer:S3
2-551-015 PaperTransfer:S4
2-551-019 PaperTransfer:S5
2-551-023 Wide Roller:PaperTransfer:S1
2-551-027 Wide Roller:PaperTransfer:S2
2-551-031 Wide Roller:PaperTransfer:S3
2-551-035 Wide Roller:PaperTransfer:S4
2-551-039 Wide Roller:PaperTransfer:S5
2552 [OHP:SizeCorrection:FC]
2-552-003 PaperTransfer:S1
2-552-007 PaperTransfer:S2
2-552-011 PaperTransfer:S3
2-552-015 PaperTransfer:S4
2-552-019 PaperTransfer:S5
2-552-023 Wide Roller:PaperTransfer:S1
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
ENG
ENG
ENG
ENG
ENG
ENG
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 181 / 1%/ step]
[100 to 995 / 229 / 1%/ step]
[100 to 995 / 286 / 1%/ step]
[100 to 995 / 381 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
2-552-027 Wide Roller:PaperTransfer:S2
2-552-031 Wide Roller:PaperTransfer:S3
2-552-035 Wide Roller:PaperTransfer:S4
2-552-039 Wide Roller:PaperTransfer:S5
2553 [OHP:Size-Env.Correct:BW]
2-553-003 PaperTransfer:S1
2-553-007 PaperTransfer:S2
2-553-011 PaperTransfer:S3
2-553-015 PaperTransfer:S4
2-553-019 PaperTransfer:S5
2-553-023 Wide Roller:PaperTransfer:S1
2-553-027 Wide Roller:PaperTransfer:S2
2-553-031 Wide Roller:PaperTransfer:S3
2-553-035 Wide Roller:PaperTransfer:S4
2-553-039 Wide Roller:PaperTransfer:S5
2554 [OHP:Size-Env.Correct:FC]
2-554-003 PaperTransfer:S1
2-554-007 PaperTransfer:S2
2-554-011 PaperTransfer:S3
2-554-015 PaperTransfer:S4
2-554-019 PaperTransfer:S5
2-554-023 Wide Roller:PaperTransfer:S1
Engine SP Tables - SP2000-2
ENG
ENG
ENG
ENG
[100 to 995 / 181 / 1%/ step]
[100 to 995 / 229 / 1%/ step]
[100 to 995 / 286 / 1%/ step]
[100 to 995 / 381 / 1%/ step]
ENG [1 to 110 / 70 / 1/step]
ENG [1 to 110 / 71 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 70 / 1/step]
ENG [1 to 110 / 71 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 77 / 1/step]
ENG [1 to 110 / 78 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 77 / 1/step]
261
262
3. Engine SP Mode Tables
2-554-027 Wide Roller:PaperTransfer:S2
2-554-031 Wide Roller:PaperTransfer:S3
2-554-035 Wide Roller:PaperTransfer:S4
2-554-039 Wide Roller:PaperTransfer:S5
2555 [OHP:LeadingEdgeCorrection]
2-555-003 Paper Transfer
2556 [OHP:SwitchTimingLeadEdge]
2-556-003 Paper Transfer
2557 [OHP:TrailEdgeCorrection]
2-557-003 Paper Transfer
2558 [OHP:SwitchTimingTrailEdge]
2-558-003 Paper Transfer
2563 [Special1:Bias:BW]
2-563-001 PaperTransfer:standard:1side
2-563-002 PaperTransfer:standard:2side
2-563-003 PaperTransfer:low:1side
2-563-004 PaperTransfer:low:2side
2567 [Special1:Bias:FC]
2-567-001 PaperTransfer:standard:1side
2-567-002 PaperTransfer:standard:2side
2-567-003 PaperTransfer:low:1side
2-567-004 PaperTransfer:low:2side
ENG [1 to 110 / 78 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 200 / 22 / 1-uA/step]
ENG [0 to 200 / 22 / 1-uA/step]
ENG [0 to 200 / 11 / 1-uA/step]
ENG [0 to 200 / 11 / 1-uA/step]
ENG [0 to 200 / 29 / 1-uA/step]
ENG [0 to 200 / 29 / 1-uA/step]
ENG [0 to 200 / 14 / 1-uA/step]
ENG [0 to 200 / 14 / 1-uA/step]
Engine SP Tables - SP2000-2
2571 [Special1:SizeCorrection:BW]
2-571-001 PaperTransfer:Standard:1Sid:S1
2-571-002 PaperTransfer:Standard:2Sid:S1
2-571-003 PaperTransfer:Low:1Side:S1
2-571-004 PaperTransfer:Low:2Side:S1
2-571-005 PaperTransfer:Standard:1Sid:S2
2-571-006 PaperTransfer:Standard:2Sid:S2
2-571-007 PaperTransfer:Low:1Side:S2
2-571-008 PaperTransfer:Low:2Side:S2
2-571-009 PaperTransfer:Standard:1Sid:S3
2-571-010 PaperTransfer:Standard:2Sid:S3
2-571-011 PaperTransfer:Low:1Side:S3
2-571-012 PaperTransfer:Low:2Side:S3
2-571-013 PaperTransfer:Standard:1Sid:S4
2-571-014 PaperTransfer:Standard:2Sid:S4
2-571-015 PaperTransfer:Low:1Side:S4
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 131 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
263
264
3. Engine SP Mode Tables
2-571-016 PaperTransfer:Low:2Side:S4
2-571-017 PaperTransfer:Standard:1Sid:S5
2-571-018 PaperTransfer:Standard:2Sid:S5
2-571-019 PaperTransfer:Low:1Side:S5
ENG [100 to 995 / 131 / 1%/ step]
ENG [100 to 995 / 132 / 1%/ step]
ENG [100 to 995 / 184 / 1%/ step]
ENG [100 to 995 / 132 / 1%/ step]
2-571-020 PaperTransfer:Low:2Side:S5
2-571-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
2-571-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [100 to 995 / 184 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
2-571-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-571-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-571-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
ENG [100 to 995 / 100 / 1%/ step]
2-571-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [100 to 995 / 105 / 1%/ step]
2-571-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [100 to 995 / 100 / 1%/ step]
2-571-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [100 to 995 / 105 / 1%/ step]
2-571-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
ENG [100 to 995 / 105 / 1%/ step]
2-571-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [100 to 995 / 118 / 1%/ step]
2-571-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [100 to 995 / 105 / 1%/ step]
Engine SP Tables - SP2000-2
2-571-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [100 to 995 / 118 / 1%/ step]
2-571-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
ENG [100 to 995 / 118 / 1%/ step]
2-571-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG [100 to 995 / 131 / 1%/ step]
2-571-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [100 to 995 / 118 / 1%/ step]
2-571-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [100 to 995 / 131 / 1%/ step]
2-571-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
ENG [100 to 995 / 132 / 1%/ step]
2-571-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [100 to 995 / 184 / 1%/ step]
2-571-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [100 to 995 / 132 / 1%/ step]
2-571-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [100 to 995 / 184 / 1%/ step]
2572 [Special1:SizeCorrection:FC]
2-572-001 PaperTransfer:Standard:1Sid:S1
2-572-002 PaperTransfer:Standard:2Sid:S1
2-572-003 PaperTransfer:Low:1Side:S1
2-572-004 PaperTransfer:Low:2Side:S1
2-572-005 PaperTransfer:Standard:1Sid:S2
2-572-006 PaperTransfer:Standard:2Sid:S2
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 120 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
265
266
3. Engine SP Mode Tables
2-572-007 PaperTransfer:Low:1Side:S2
2-572-008 PaperTransfer:Low:2Side:S2
2-572-009 PaperTransfer:Standard:1Sid:S3
2-572-010 PaperTransfer:Standard:2Sid:S3
2-572-011 PaperTransfer:Low:1Side:S3
2-572-012 PaperTransfer:Low:2Side:S3
2-572-013 PaperTransfer:Standard:1Sid:S4
2-572-014 PaperTransfer:Standard:2Sid:S4
2-572-015 PaperTransfer:Low:1Side:S4
2-572-016 PaperTransfer:Low:2Side:S4
2-572-017 PaperTransfer:Standard:1Sid:S5
2-572-018 PaperTransfer:Standard:2Sid:S5
2-572-019 PaperTransfer:Low:1Side:S5
2-572-020 PaperTransfer:Low:2Side:S5
2-572-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
2-572-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [100 to 995 / 120 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 180 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 180 / 1%/ step]
ENG [100 to 995 / 130 / 1%/ step]
ENG [100 to 995 / 200 / 1%/ step]
ENG [100 to 995 / 130 / 1%/ step]
ENG [100 to 995 / 200 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 240 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 240 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
Engine SP Tables - SP2000-2
2-572-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-572-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-572-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
2-572-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG
ENG
[100 to 995 / 120 / 1%/ step]
[100 to 995 / 140 / 1%/ step]
2-572-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [100 to 995 / 120 / 1%/ step]
2-572-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [100 to 995 / 140 / 1%/ step]
2-572-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
2-572-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG
ENG
[100 to 995 / 118 / 1%/ step]
[100 to 995 / 180 / 1%/ step]
2-572-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [100 to 995 / 118 / 1%/ step]
2-572-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [100 to 995 / 180 / 1%/ step]
2-572-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
2-572-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG
ENG
[100 to 995 / 130 / 1%/ step]
[100 to 995 / 200 / 1%/ step]
2-572-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [100 to 995 / 130 / 1%/ step]
2-572-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [100 to 995 / 200 / 1%/ step]
2-572-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
2-572-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG
ENG
[100 to 995 / 140 / 1%/ step]
[100 to 995 / 240 / 1%/ step]
267
268
3. Engine SP Mode Tables
2-572-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [100 to 995 / 140 / 1%/ step]
2-572-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [100 to 995 / 240 / 1%/ step]
2573 [Special1:Size-Env.Correct:BW]
2-573-001 PaperTransfer:Standard:1Sid:S1
2-573-002 PaperTransfer:Standard:2Sid:S1
2-573-003 PaperTransfer:Low:1Side:S1
2-573-004 PaperTransfer:Low:2Side:S1
2-573-005 PaperTransfer:Standard:1Sid:S2
2-573-006 PaperTransfer:Standard:2Sid:S2
2-573-007 PaperTransfer:Low:1Side:S2
2-573-008 PaperTransfer:Low:2Side:S2
2-573-009 PaperTransfer:Standard:1Sid:S3
2-573-010 PaperTransfer:Standard:2Sid:S3
2-573-011 PaperTransfer:Low:1Side:S3
2-573-012 PaperTransfer:Low:2Side:S3
2-573-013 PaperTransfer:Standard:1Sid:S4
2-573-014 PaperTransfer:Standard:2Sid:S4
2-573-015 PaperTransfer:Low:1Side:S4
2-573-016 PaperTransfer:Low:2Side:S4
2-573-017 PaperTransfer:Standard:1Sid:S5
2-573-018 PaperTransfer:Standard:2Sid:S5
2-573-019 PaperTransfer:Low:1Side:S5
2-573-020 PaperTransfer:Low:2Side:S5
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[1 to 110 / 10 / 1/step]
[1 to 110 / 15 / 1/step]
[1 to 110 / 10 / 1/step]
[1 to 110 / 15 / 1/step]
[1 to 110 / 11 / 1/step]
[1 to 110 / 16 / 1/step]
[1 to 110 / 11 / 1/step]
[1 to 110 / 16 / 1/step]
[1 to 110 / 12 / 1/step]
[1 to 110 / 17 / 1/step]
[1 to 110 / 12 / 1/step]
[1 to 110 / 17 / 1/step]
[1 to 110 / 13 / 1/step]
ENG [1 to 110 / 18 / 1/step]
ENG [1 to 110 / 13 / 1/step]
[1 to 110 / 18 / 1/step]
[1 to 110 / 14 / 1/step]
[1 to 110 / 19 / 1/step]
[1 to 110 / 14 / 1/step]
[1 to 110 / 19 / 1/step]
Engine SP Tables - SP2000-2
2-573-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
2-573-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG
ENG
[1 to 110 / 10 / 1/step]
[1 to 110 / 15 / 1/step]
2-573-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [1 to 110 / 10 / 1/step]
2-573-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [1 to 110 / 15 / 1/step]
2-573-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
ENG [1 to 110 / 11 / 1/step]
2-573-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [1 to 110 / 16 / 1/step]
2-573-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [1 to 110 / 11 / 1/step]
2-573-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [1 to 110 / 16 / 1/step]
2-573-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
ENG [1 to 110 / 12 / 1/step]
2-573-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [1 to 110 / 17 / 1/step]
2-573-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [1 to 110 / 12 / 1/step]
2-573-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [1 to 110 / 17 / 1/step]
2-573-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
ENG [1 to 110 / 13 / 1/step]
2-573-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG [1 to 110 / 18 / 1/step]
2-573-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [1 to 110 / 13 / 1/step]
2-573-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [1 to 110 / 18 / 1/step]
2-573-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
ENG [1 to 110 / 14 / 1/step]
2-573-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [1 to 110 / 19 / 1/step]
2-573-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [1 to 110 / 14 / 1/step]
2-573-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [1 to 110 / 19 / 1/step]
269
270
3. Engine SP Mode Tables
2574 [Special1:Size-Env.Correct:FC]
2-574-001 PaperTransfer:Standard:1Sid:S1
2-574-002 PaperTransfer:Standard:2Sid:S1
2-574-003 PaperTransfer:Low:1Side:S1
2-574-004 PaperTransfer:Low:2Side:S1
2-574-005 PaperTransfer:Standard:1Sid:S2
2-574-006 PaperTransfer:Standard:2Sid:S2
2-574-007 PaperTransfer:Low:1Side:S2
2-574-008 PaperTransfer:Low:2Side:S2
2-574-009 PaperTransfer:Standard:1Sid:S3
2-574-010 PaperTransfer:Standard:2Sid:S3
2-574-011 PaperTransfer:Low:1Side:S3
2-574-012 PaperTransfer:Low:2Side:S3
2-574-013 PaperTransfer:Standard:1Sid:S4
2-574-014 PaperTransfer:Standard:2Sid:S4
ENG [1 to 110 / 20 / 1/step]
ENG [1 to 110 / 25 / 1/step]
ENG [1 to 110 / 20 / 1/step]
ENG [1 to 110 / 25 / 1/step]
ENG [1 to 110 / 21 / 1/step]
ENG [1 to 110 / 26 / 1/step]
ENG [1 to 110 / 21 / 1/step]
ENG [1 to 110 / 26 / 1/step]
ENG [1 to 110 / 22 / 1/step]
ENG [1 to 110 / 27 / 1/step]
ENG [1 to 110 / 22 / 1/step]
ENG [1 to 110 / 27 / 1/step]
ENG [1 to 110 / 23 / 1/step]
ENG [1 to 110 / 28 / 1/step]
2-574-015 PaperTransfer:Low:1Side:S4
2-574-016 PaperTransfer:Low:2Side:S4
2-574-017 PaperTransfer:Standard:1Sid:S5
2-574-018 PaperTransfer:Standard:2Sid:S5
2-574-019 PaperTransfer:Low:1Side:S5
ENG
ENG
ENG
[1 to 110 / 23 / 1/step]
[1 to 110 / 28 / 1/step]
[1 to 110 / 24 / 1/step]
ENG [1 to 110 / 29 / 1/step]
ENG [1 to 110 / 24 / 1/step]
2-574-020 PaperTransfer:Low:2Side:S5
2-574-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
ENG
ENG
[1 to 110 / 29 / 1/step]
[1 to 110 / 20 / 1/step]
2-574-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [1 to 110 / 25 / 1/step]
2-574-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [1 to 110 / 20 / 1/step]
Engine SP Tables - SP2000-2
2-574-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [1 to 110 / 25 / 1/step]
2-574-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
ENG [1 to 110 / 21 / 1/step]
2-574-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [1 to 110 / 26 / 1/step]
2-574-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [1 to 110 / 21 / 1/step]
2-574-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [1 to 110 / 26 / 1/step]
ENG [1 to 110 / 22 / 1/step] 2-574-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
2-574-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [1 to 110 / 27 / 1/step]
2-574-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [1 to 110 / 22 / 1/step]
2-574-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [1 to 110 / 27 / 1/step]
ENG [1 to 110 / 23 / 1/step] 2-574-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
2-574-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG [1 to 110 / 28 / 1/step]
2-574-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [1 to 110 / 23 / 1/step]
2-574-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [1 to 110 / 28 / 1/step]
ENG [1 to 110 / 24 / 1/step] 2-574-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
2-574-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [1 to 110 / 29 / 1/step]
2-574-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [1 to 110 / 24 / 1/step]
2-574-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [1 to 110 / 29 / 1/step]
2575 [Special1:LeadingEdgeCorrection]
2-575-001 PaperTransfer:Standard:1Side
2-575-002 PaperTransfer:Standard:2Side
ENG
ENG
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
271
272
3. Engine SP Mode Tables
2-575-003 Paper Transfer:Low:1side
2-575-004 Paper Transfer:Low:2side
2576 [Special1:SwitchTimingLeadEdge]
2-576-001 PaperTransfer:Standard:1side
2-576-002 PaperTransfer:Standard:2side
2-576-003 Paper Transfer:Low:1side
2-576-004 Paper Transfer:Low:2side
2577 [Special1:TrailEdgeCorrection]
2-577-001 PaperTransfer:Standard:1Side
2-577-002 PaperTransfer:Standard:2Side
2-577-003 Paper Transfer:Low:1side
2-577-004 Paper Transfer:Low:2side
2578 [Special1:SwitchTimingTrailEdge]
2-578-001 PaperTransfer:Standard:1side
2-578-002 PaperTransfer:Standard:2side
2-578-003 Paper Transfer:Low:1side
2-578-004 Paper Transfer:Low:2side
2583 [Special2:Bias:BW]
2-583-001 PaperTransfer:standard:1side
2-583-002 PaperTransfer:standard:2side
2-583-003 PaperTransfer:low:1side
2-583-004 PaperTransfer:low:2side
2587 [Special2:Bias:FC]
ENG
ENG
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 200 / 22 / 1-uA/step]
ENG [0 to 200 / 22 / 1-uA/step]
ENG [0 to 200 / 11 / 1-uA/step]
ENG [0 to 200 / 11 / 1-uA/step]
2-587-001 PaperTransfer:standard:1side
2-587-002 PaperTransfer:standard:2side
2-587-003 PaperTransfer:low:1side
2-587-004 PaperTransfer:low:2side
2591 [Special2:SizeCorrection:BW]
2-591-001 PaperTransfer:standard:1Sid:S1
2-591-002 PaperTransfer:standard:2Sid:S1
2-591-003 PaperTransfer:Low:1Side:S1
2-591-004 PaperTransfer:Low:2Side:S1
2-591-005 PaperTransfer:standard:1Sid:S2
2-591-006 PaperTransfer:standard:2Sid:S2
2-591-007 PaperTransfer:Low:1Side:S2
2-591-008 PaperTransfer:Low:2Side:S2
2-591-009 PaperTransfer:standard:1Sid:S3
2-591-010 PaperTransfer:standard:2Sid:S3
2-591-011 PaperTransfer:Low:1Side:S3
2-591-012 PaperTransfer:Low:2Side:S3
Engine SP Tables - SP2000-2
ENG [0 to 200 / 29 / 1-uA/step]
ENG [0 to 200 / 29 / 1-uA/step]
ENG [0 to 200 / 14 / 1-uA/step]
ENG [0 to 200 / 14 / 1-uA/step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
273
274
3. Engine SP Mode Tables
2-591-013 PaperTransfer:standard:1Sid:S4
2-591-014 PaperTransfer:standard:2Sid:S4
2-591-015 PaperTransfer:Low:1Side:S4
2-591-016 PaperTransfer:Low:2Side:S4
2-591-017 PaperTransfer:Standard:1Sid:S5
2-591-018 PaperTransfer:Standard:2Sid:S5
2-591-019 PaperTransfer:Low:1Side:S5
2-591-020 PaperTransfer:Low:2Side:S5
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 131 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 131 / 1%/ step]
ENG [100 to 995 / 132 / 1%/ step]
ENG [100 to 995 / 184 / 1%/ step]
ENG [100 to 995 / 132 / 1%/ step]
ENG [100 to 995 / 184 / 1%/ step]
2-591-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
2-591-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
2-591-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-591-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-591-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
2-591-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
2-591-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [100 to 995 / 100 / 1%/ step]
2-591-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [100 to 995 / 105 / 1%/ step]
Engine SP Tables - SP2000-2
2-591-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
2-591-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
2-591-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [100 to 995 / 105 / 1%/ step]
2-591-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [100 to 995 / 118 / 1%/ step]
2-591-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
2-591-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 131 / 1%/ step]
2-591-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [100 to 995 / 118 / 1%/ step]
2-591-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [100 to 995 / 131 / 1%/ step]
2-591-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
2-591-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [100 to 995 / 132 / 1%/ step]
ENG [100 to 995 / 184 / 1%/ step]
2-591-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [100 to 995 / 132 / 1%/ step]
2-591-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [100 to 995 / 184 / 1%/ step]
2592 [Special2:SizeCorrection:FC]
2-592-001 PaperTransfer:standard:1Sid:S1
2-592-002 PaperTransfer:standard:2Sid:S1
2-592-003 PaperTransfer:Low:1Side:S1
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
275
276
3. Engine SP Mode Tables
2-592-004 PaperTransfer:Low:2Side:S1
2-592-005 PaperTransfer:standard:1Sid:S2
2-592-006 PaperTransfer:standard:2Sid:S2
2-592-007 PaperTransfer:Low:1Side:S2
2-592-008 PaperTransfer:Low:2Side:S2
2-592-009 PaperTransfer:standard:1Sid:S3
2-592-010 PaperTransfer:standard:2Sid:S3
2-592-011 PaperTransfer:Low:1Side:S3
2-592-012 PaperTransfer:Low:2Side:S3
2-592-013 PaperTransfer:standard:1Sid:S4
2-592-014 PaperTransfer:standard:2Sid:S4
2-592-015 PaperTransfer:Low:1Side:S4
2-592-016 PaperTransfer:Low:2Side:S4
2-592-017 PaperTransfer:Standard:1Sid:S5
2-592-018 PaperTransfer:Standard:2Sid:S5
2-592-019 PaperTransfer:Low:1Side:S5
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 120 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 120 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 180 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 180 / 1%/ step]
ENG [100 to 995 / 130 / 1%/ step]
ENG [100 to 995 / 200 / 1%/ step]
ENG [100 to 995 / 130 / 1%/ step]
ENG [100 to 995 / 200 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 240 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
Engine SP Tables - SP2000-2
2-592-020 PaperTransfer:Low:2Side:S5
2-592-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
2-592-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [100 to 995 / 240 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
2-592-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-592-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-592-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
ENG [100 to 995 / 120 / 1%/ step]
2-592-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [100 to 995 / 140 / 1%/ step]
2-592-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [100 to 995 / 120 / 1%/ step]
2-592-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [100 to 995 / 140 / 1%/ step]
2-592-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
ENG [100 to 995 / 118 / 1%/ step]
2-592-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [100 to 995 / 180 / 1%/ step]
2-592-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [100 to 995 / 118 / 1%/ step]
2-592-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [100 to 995 / 180 / 1%/ step]
2-592-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
ENG [100 to 995 / 130 / 1%/ step]
2-592-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG [100 to 995 / 200 / 1%/ step]
2-592-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [100 to 995 / 130 / 1%/ step]
277
278
3. Engine SP Mode Tables
2-592-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [100 to 995 / 200 / 1%/ step]
2-592-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
ENG [100 to 995 / 140 / 1%/ step]
2-592-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [100 to 995 / 240 / 1%/ step]
2-592-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [100 to 995 / 140 / 1%/ step]
2-592-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [100 to 995 / 240 / 1%/ step]
2593 [Special2:Size-Env.Correct:BW]
2-593-001 PaperTransfer:standard:1Sid:S1
2-593-002 PaperTransfer:standard:2Sid:S1
2-593-003 PaperTransfer:Low:1Side:S1
2-593-004 PaperTransfer:Low:2Side:S1
2-593-005 PaperTransfer:standard:1Sid:S2
2-593-006 PaperTransfer:standard:2Sid:S2
2-593-007 PaperTransfer:Low:1Side:S2
2-593-008 PaperTransfer:Low:2Side:S2
2-593-009 PaperTransfer:standard:1Sid:S3
2-593-010 PaperTransfer:standard:2Sid:S3
2-593-011 PaperTransfer:Low:1Side:S3
2-593-012 PaperTransfer:Low:2Side:S3
2-593-013 PaperTransfer:standard:1Sid:S4
2-593-014 PaperTransfer:standard:2Sid:S4
2-593-015 PaperTransfer:Low:1Side:S4
2-593-016 PaperTransfer:Low:2Side:S4
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[1 to 110 / 10 / 1/step]
[1 to 110 / 15 / 1/step]
[1 to 110 / 10 / 1/step]
[1 to 110 / 15 / 1/step]
[1 to 110 / 11 / 1/step]
[1 to 110 / 16 / 1/step]
[1 to 110 / 11 / 1/step]
[1 to 110 / 16 / 1/step]
[1 to 110 / 12 / 1/step]
[1 to 110 / 17 / 1/step]
[1 to 110 / 12 / 1/step]
[1 to 110 / 17 / 1/step]
[1 to 110 / 13 / 1/step]
ENG [1 to 110 / 18 / 1/step]
ENG [1 to 110 / 13 / 1/step]
ENG [1 to 110 / 18 / 1/step]
Engine SP Tables - SP2000-2
2-593-017 PaperTransfer:Standard:1Sid:S5
2-593-018 PaperTransfer:Standard:2Sid:S5
2-593-019 PaperTransfer:Low:1Side:S5
ENG [1 to 110 / 14 / 1/step]
ENG [1 to 110 / 19 / 1/step]
ENG [1 to 110 / 14 / 1/step]
2-593-020 PaperTransfer:Low:2Side:S5
2-593-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
ENG
ENG
[1 to 110 / 19 / 1/step]
[1 to 110 / 10 / 1/step]
2-593-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [1 to 110 / 15 / 1/step]
2-593-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [1 to 110 / 10 / 1/step]
2-593-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [1 to 110 / 15 / 1/step]
2-593-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
ENG [1 to 110 / 11 / 1/step]
2-593-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [1 to 110 / 16 / 1/step]
2-593-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [1 to 110 / 11 / 1/step]
2-593-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [1 to 110 / 16 / 1/step]
2-593-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
ENG [1 to 110 / 12 / 1/step]
2-593-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [1 to 110 / 17 / 1/step]
2-593-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [1 to 110 / 12 / 1/step]
2-593-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [1 to 110 / 17 / 1/step]
ENG [1 to 110 / 13 / 1/step] 2-593-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
2-593-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG [1 to 110 / 18 / 1/step]
2-593-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [1 to 110 / 13 / 1/step]
2-593-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [1 to 110 / 18 / 1/step]
279
280
3. Engine SP Mode Tables
2-593-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
2-593-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG
ENG
[1 to 110 / 14 / 1/step]
[1 to 110 / 19 / 1/step]
2-593-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [1 to 110 / 14 / 1/step]
2-593-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [1 to 110 / 19 / 1/step]
2594 [Special2:Size-Env.Correct:FC]
2-594-001 PaperTransfer:standard:1Sid:S1
2-594-002 PaperTransfer:standard:2Sid:S1
2-594-003 PaperTransfer:Low:1Side:S1
2-594-004 PaperTransfer:Low:2Side:S1
2-594-005 PaperTransfer:standard:1Sid:S2
2-594-006 PaperTransfer:standard:2Sid:S2
2-594-007 PaperTransfer:Low:1Side:S2
2-594-008 PaperTransfer:Low:2Side:S2
2-594-009 PaperTransfer:standard:1Sid:S3
2-594-010 PaperTransfer:standard:2Sid:S3
2-594-011 PaperTransfer:Low:1Side:S3
2-594-012 PaperTransfer:Low:2Side:S3
2-594-013 PaperTransfer:standard:1Sid:S4
2-594-014 PaperTransfer:standard:2Sid:S4
2-594-015 PaperTransfer:Low:1Side:S4
2-594-016 PaperTransfer:Low:2Side:S4
2-594-017 PaperTransfer:Standard:1Sid:S5
2-594-018 PaperTransfer:Standard:2Sid:S5
2-594-019 PaperTransfer:Low:1Side:S5
ENG [1 to 110 / 20 / 1/step]
ENG [1 to 110 / 25 / 1/step]
ENG [1 to 110 / 20 / 1/step]
ENG [1 to 110 / 25 / 1/step]
ENG [1 to 110 / 21 / 1/step]
ENG [1 to 110 / 26 / 1/step]
ENG [1 to 110 / 21 / 1/step]
ENG [1 to 110 / 26 / 1/step]
ENG
ENG
ENG
ENG [1 to 110 / 27 / 1/step]
ENG [1 to 110 / 23 / 1/step]
ENG
ENG
ENG
ENG
ENG
ENG
[1 to 110 / 22 / 1/step]
[1 to 110 / 27 / 1/step]
[1 to 110 / 22 / 1/step]
[1 to 110 / 28 / 1/step]
[1 to 110 / 23 / 1/step]
[1 to 110 / 28 / 1/step]
[1 to 110 / 24 / 1/step]
[1 to 110 / 29 / 1/step]
[1 to 110 / 24 / 1/step]
Engine SP Tables - SP2000-2
2-594-020 PaperTransfer:Low:2Side:S5
2-594-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
ENG
ENG
[1 to 110 / 29 / 1/step]
[1 to 110 / 20 / 1/step]
2-594-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [1 to 110 / 25 / 1/step]
2-594-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [1 to 110 / 20 / 1/step]
2-594-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [1 to 110 / 25 / 1/step]
ENG [1 to 110 / 21 / 1/step] 2-594-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
2-594-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [1 to 110 / 26 / 1/step]
2-594-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [1 to 110 / 21 / 1/step]
2-594-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [1 to 110 / 26 / 1/step]
ENG [1 to 110 / 22 / 1/step] 2-594-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
2-594-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [1 to 110 / 27 / 1/step]
2-594-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [1 to 110 / 22 / 1/step]
2-594-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [1 to 110 / 27 / 1/step]
ENG [1 to 110 / 23 / 1/step] 2-594-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
2-594-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG [1 to 110 / 28 / 1/step]
2-594-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [1 to 110 / 23 / 1/step]
2-594-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [1 to 110 / 28 / 1/step]
2-594-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
2-594-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG
ENG
[1 to 110 / 24 / 1/step]
[1 to 110 / 29 / 1/step]
2-594-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [1 to 110 / 24 / 1/step]
281
282
3. Engine SP Mode Tables
2-594-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [1 to 110 / 29 / 1/step]
2595 [Special2:LeadingEdgeCorrection]
2-595-001 PaperTransfer:standard:1Side
2-595-002 PaperTransfer:standard:2Side
2-595-003 Paper Transfer:Low:1side
2-595-004 Paper Transfer:Low:2side
2596 [Special2:SwitchTimingLeadEdge]
2-596-001 PaperTransfer:standard:1side
2-596-002 PaperTransfer:standard:2side
2-596-003 Paper Transfer:Low:1side
2-596-004 Paper Transfer:Low:2side
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
2597 [Special2:TrailEdgeCorrection]
2-597-001 PaperTransfer:standard:1Side
2-597-002 PaperTransfer:standard:2Side
2-597-003 Paper Transfer:Low:1side
2-597-004 Paper Transfer:Low:2side
2598 [Special2:SwitchTimingTrailEdge]
2-598-001 PaperTransfer:standard:1side
2-598-002 PaperTransfer:standard:2side
2-598-003 Paper Transfer:Low:1side
2-598-004 Paper Transfer:Low:2side
2603 [Special3:Bias:BW]
2-603-001 PaperTransfer:standard:1side
ENG
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG
ENG
ENG
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
[0 to 200 / 22 / 1-uA/step]
2-603-002 PaperTransfer:standard:2side
2-603-003 PaperTransfer:low:1side
2-603-004 PaperTransfer:low:2side
2607 [Special3:Bias:FC]
2-607-001 PaperTransfer:standard:1side
2-607-002 PaperTransfer:standard:2side
2-607-003 PaperTransfer:low:1side
2-607-004 PaperTransfer:low:2side
2611 [Special3:SizeCorrection:BW]
2-611-001 PaperTransfer:standard:1Sid:S1
2-611-002 PaperTransfer:standard:2Sid:S1
2-611-003 PaperTransfer:Low:1Side:S1
2-611-004 PaperTransfer:Low:2Side:S1
2-611-005 PaperTransfer:standard:1Sid:S2
2-611-006 PaperTransfer:standard:2Sid:S2
2-611-007 PaperTransfer:Low:1Side:S2
2-611-008 PaperTransfer:Low:2Side:S2
2-611-009 PaperTransfer:standard:1Sid:S3
2-611-010 PaperTransfer:standard:2Sid:S3
Engine SP Tables - SP2000-2
ENG [0 to 200 / 22 / 1-uA/step]
ENG [0 to 200 / 11 / 1-uA/step]
ENG [0 to 200 / 11 / 1-uA/step]
ENG [0 to 200 / 29 / 1-uA/step]
ENG [0 to 200 / 29 / 1-uA/step]
ENG [0 to 200 / 14 / 1-uA/step]
ENG [0 to 200 / 14 / 1-uA/step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
283
284
3. Engine SP Mode Tables
2-611-011 PaperTransfer:Low:1Side:S3
2-611-012 PaperTransfer:Low:2Side:S3
2-611-013 PaperTransfer:standard:1Sid:S4
2-611-014 PaperTransfer:standard:2Sid:S4
2-611-015 PaperTransfer:Low:1Side:S4
2-611-016 PaperTransfer:Low:2Side:S4
2-611-017 PaperTransfer:Standard:1Sid:S5
2-611-018 PaperTransfer:Standard:2Sid:S5
ENG [100 to 995 / 105 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 131 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 131 / 1%/ step]
ENG [100 to 995 / 132 / 1%/ step]
ENG [100 to 995 / 184 / 1%/ step]
2-611-019 PaperTransfer:Low:1Side:S5
2-611-020 PaperTransfer:Low:2Side:S5
2-611-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
2-611-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [100 to 995 / 132 / 1%/ step]
ENG [100 to 995 / 184 / 1%/ step]
ENG
ENG
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
2-611-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-611-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-611-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
2-611-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 105 / 1%/ step]
Engine SP Tables - SP2000-2
2-611-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [100 to 995 / 100 / 1%/ step]
2-611-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [100 to 995 / 105 / 1%/ step]
2-611-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
2-611-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG
ENG
[100 to 995 / 105 / 1%/ step]
[100 to 995 / 118 / 1%/ step]
2-611-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [100 to 995 / 105 / 1%/ step]
2-611-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [100 to 995 / 118 / 1%/ step]
2-611-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
2-611-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG
ENG
[100 to 995 / 118 / 1%/ step]
[100 to 995 / 131 / 1%/ step]
2-611-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [100 to 995 / 118 / 1%/ step]
2-611-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [100 to 995 / 131 / 1%/ step]
2-611-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
2-611-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG
ENG
[100 to 995 / 132 / 1%/ step]
[100 to 995 / 184 / 1%/ step]
2-611-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [100 to 995 / 132 / 1%/ step]
2-611-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [100 to 995 / 184 / 1%/ step]
2612 [Special3:SizeCorrection:FC]
2-612-002 PaperTransfer:standard:2Sid:S1 ENG [100 to 995 / 100 / 1%/ step]
285
286
3. Engine SP Mode Tables
2-612-003 PaperTransfer:Low:1Side:S1
2-612-004 PaperTransfer:Low:2Side:S1
2-612-005 PaperTransfer:standard:1Sid:S2
2-612-006 PaperTransfer:standard:2Sid:S2
2-612-007 PaperTransfer:Low:1Side:S2
2-612-008 PaperTransfer:Low:2Side:S2
2-612-009 PaperTransfer:standard:1Sid:S3
2-612-010 PaperTransfer:standard:2Sid:S3
2-612-011 PaperTransfer:Low:1Side:S3
2-612-012 PaperTransfer:Low:2Side:S3
2-612-013 PaperTransfer:standard:1Sid:S4
2-612-014 PaperTransfer:standard:2Sid:S4
2-612-015 PaperTransfer:Low:1Side:S4
2-612-016 PaperTransfer:Low:2Side:S4
2-612-017 PaperTransfer:Standard:1Sid:S5
2-612-018 PaperTransfer:Standard:2Sid:S5
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 100 / 1%/ step]
ENG [100 to 995 / 120 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 120 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 180 / 1%/ step]
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 180 / 1%/ step]
ENG [100 to 995 / 130 / 1%/ step]
ENG [100 to 995 / 200 / 1%/ step]
ENG [100 to 995 / 130 / 1%/ step]
ENG [100 to 995 / 200 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 240 / 1%/ step]
Engine SP Tables - SP2000-2
2-612-019 PaperTransfer:Low:1Side:S5
2-612-020 PaperTransfer:Low:2Side:S5
2-612-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
2-612-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [100 to 995 / 140 / 1%/ step]
ENG [100 to 995 / 240 / 1%/ step]
ENG
ENG
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
2-612-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-612-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [100 to 995 / 100 / 1%/ step]
2-612-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
2-612-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [100 to 995 / 120 / 1%/ step]
ENG [100 to 995 / 140 / 1%/ step]
2-612-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [100 to 995 / 120 / 1%/ step]
2-612-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [100 to 995 / 140 / 1%/ step]
2-612-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
2-612-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [100 to 995 / 118 / 1%/ step]
ENG [100 to 995 / 180 / 1%/ step]
2-612-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [100 to 995 / 118 / 1%/ step]
2-612-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [100 to 995 / 180 / 1%/ step]
2-612-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
2-612-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG [100 to 995 / 130 / 1%/ step]
ENG [100 to 995 / 200 / 1%/ step]
287
288
3. Engine SP Mode Tables
2-612-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [100 to 995 / 130 / 1%/ step]
2-612-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [100 to 995 / 200 / 1%/ step]
2-612-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
2-612-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG
ENG
[100 to 995 / 140 / 1%/ step]
[100 to 995 / 240 / 1%/ step]
2-612-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [100 to 995 / 140 / 1%/ step]
2-612-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [100 to 995 / 240 / 1%/ step]
2613 [Special3:Size-Env.Correct:BW]
2-613-001 PaperTransfer:standard:1Sid:S1
2-613-002 PaperTransfer:standard:2Sid:S1
2-613-003 PaperTransfer:Low:1Side:S1
2-613-004 PaperTransfer:Low:2Side:S1
2-613-005 PaperTransfer:standard:1Sid:S2
2-613-006 PaperTransfer:standard:2Sid:S2
2-613-007 PaperTransfer:Low:1Side:S2
2-613-008 PaperTransfer:Low:2Side:S2
2-613-009 PaperTransfer:standard:1Sid:S3
2-613-010 PaperTransfer:standard:2Sid:S3
2-613-011 PaperTransfer:Low:1Side:S3
2-613-012 PaperTransfer:Low:2Side:S3
2-613-013 PaperTransfer:standard:1Sid:S4
2-613-014 PaperTransfer:standard:2Sid:S4
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[1 to 110 / 10 / 1/step]
[1 to 110 / 15 / 1/step]
[1 to 110 / 10 / 1/step]
[1 to 110 / 15 / 1/step]
[1 to 110 / 11 / 1/step]
[1 to 110 / 16 / 1/step]
[1 to 110 / 11 / 1/step]
[1 to 110 / 16 / 1/step]
[1 to 110 / 12 / 1/step]
ENG [1 to 110 / 17 / 1/step]
ENG [1 to 110 / 12 / 1/step]
[1 to 110 / 17 / 1/step]
[1 to 110 / 13 / 1/step]
[1 to 110 / 18 / 1/step]
Engine SP Tables - SP2000-2
2-613-015 PaperTransfer:Low:1Side:S4
2-613-016 PaperTransfer:Low:2Side:S4
2-613-017 PaperTransfer:Standard:1Sid:S5
ENG [1 to 110 / 13 / 1/step]
ENG [1 to 110 / 18 / 1/step]
ENG [1 to 110 / 14 / 1/step]
2-613-018 PaperTransfer:Standard:2Sid:S5
2-613-019 PaperTransfer:Low:1Side:S5
ENG
ENG
[1 to 110 / 19 / 1/step]
[1 to 110 / 14 / 1/step]
2-613-020 PaperTransfer:Low:2Side:S5
2-613-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
ENG
ENG
[1 to 110 / 19 / 1/step]
[1 to 110 / 10 / 1/step]
2-613-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [1 to 110 / 15 / 1/step]
2-613-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [1 to 110 / 10 / 1/step]
2-613-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [1 to 110 / 15 / 1/step]
2-613-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
ENG [1 to 110 / 11 / 1/step]
2-613-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [1 to 110 / 16 / 1/step]
2-613-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [1 to 110 / 11 / 1/step]
2-613-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [1 to 110 / 16 / 1/step]
2-613-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
ENG [1 to 110 / 12 / 1/step]
2-613-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [1 to 110 / 17 / 1/step]
2-613-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [1 to 110 / 12 / 1/step]
2-613-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [1 to 110 / 17 / 1/step]
2-613-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
2-613-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG
ENG
[1 to 110 / 13 / 1/step]
[1 to 110 / 18 / 1/step]
2-613-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [1 to 110 / 13 / 1/step]
289
290
3. Engine SP Mode Tables
2-613-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [1 to 110 / 18 / 1/step]
2-613-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
ENG [1 to 110 / 14 / 1/step]
2-613-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [1 to 110 / 19 / 1/step]
2-613-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [1 to 110 / 14 / 1/step]
2-613-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [1 to 110 / 19 / 1/step]
2614 [Special3:Size-Env.Correct:FC]
2-614-001 PaperTransfer:standard:1Sid:S1
2-614-002 PaperTransfer:standard:2Sid:S1
2-614-003 PaperTransfer:Low:1Side:S1
2-614-004 PaperTransfer:Low:2Side:S1
2-614-005 PaperTransfer:standard:1Sid:S2
2-614-006 PaperTransfer:standard:2Sid:S2
2-614-007 PaperTransfer:Low:1Side:S2
2-614-008 PaperTransfer:Low:2Side:S2
2-614-009 PaperTransfer:standard:1Sid:S3
2-614-010 PaperTransfer:standard:2Sid:S3
2-614-011 PaperTransfer:Low:1Side:S3
2-614-012 PaperTransfer:Low:2Side:S3
2-614-013 PaperTransfer:standard:1Sid:S4
2-614-014 PaperTransfer:standard:2Sid:S4
2-614-015 PaperTransfer:Low:1Side:S4
2-614-016 PaperTransfer:Low:2Side:S4
2-614-017 PaperTransfer:Standard:1Sid:S5
2-614-018 PaperTransfer:Standard:2Sid:S5
ENG
ENG [1 to 110 / 25 / 1/step]
ENG [1 to 110 / 20 / 1/step]
ENG [1 to 110 / 25 / 1/step]
ENG [1 to 110 / 21 / 1/step]
ENG [1 to 110 / 26 / 1/step]
ENG [1 to 110 / 21 / 1/step]
ENG
ENG
ENG
ENG [1 to 110 / 22 / 1/step]
ENG [1 to 110 / 27 / 1/step]
ENG
ENG
ENG
ENG
ENG
ENG
[1 to 110 / 20 / 1/step]
[1 to 110 / 26 / 1/step]
[1 to 110 / 22 / 1/step]
[1 to 110 / 27 / 1/step]
[1 to 110 / 23 / 1/step]
[1 to 110 / 28 / 1/step]
[1 to 110 / 23 / 1/step]
[1 to 110 / 28 / 1/step]
[1 to 110 / 24 / 1/step]
[1 to 110 / 29 / 1/step]
Engine SP Tables - SP2000-2
2-614-019 PaperTransfer:Low:1Side:S5 ENG [1 to 110 / 24 / 1/step]
2-614-020 PaperTransfer:Low:2Side:S5
2-614-021 Wide Roller:PaperTransfer:Standard:
1Sid:S1
ENG
ENG
[1 to 110 / 29 / 1/step]
[1 to 110 / 20 / 1/step]
2-614-022 Wide Roller:PaperTransfer:Standard:
2Sid:S1
ENG [1 to 110 / 25 / 1/step]
2-614-023 Wide Roller:PaperTransfer:Low:1Side:S1 ENG [1 to 110 / 20 / 1/step]
2-614-024 Wide Roller:PaperTransfer:Low:2Side:S1 ENG [1 to 110 / 25 / 1/step]
2-614-025 Wide Roller:PaperTransfer:Standard:
1Sid:S2
ENG [1 to 110 / 21 / 1/step]
2-614-026 Wide Roller:PaperTransfer:Standard:
2Sid:S2
ENG [1 to 110 / 26 / 1/step]
2-614-027 Wide Roller:PaperTransfer:Low:1Side:S2 ENG [1 to 110 / 21 / 1/step]
2-614-028 Wide Roller:PaperTransfer:Low:2Side:S2 ENG [1 to 110 / 26 / 1/step]
2-614-029 Wide Roller:PaperTransfer:Standard:
1Sid:S3
ENG [1 to 110 / 22 / 1/step]
2-614-030 Wide Roller:PaperTransfer:Standard:
2Sid:S3
ENG [1 to 110 / 27 / 1/step]
2-614-031 Wide Roller:PaperTransfer:Low:1Side:S3 ENG [1 to 110 / 22 / 1/step]
2-614-032 Wide Roller:PaperTransfer:Low:2Side:S3 ENG [1 to 110 / 27 / 1/step]
2-614-033 Wide Roller:PaperTransfer:Standard:
1Sid:S4
ENG [1 to 110 / 23 / 1/step]
2-614-034 Wide Roller:PaperTransfer:Standard:
2Sid:S4
ENG [1 to 110 / 28 / 1/step]
2-614-035 Wide Roller:PaperTransfer:Low:1Side:S4 ENG [1 to 110 / 23 / 1/step]
2-614-036 Wide Roller:PaperTransfer:Low:2Side:S4 ENG [1 to 110 / 28 / 1/step]
ENG [1 to 110 / 24 / 1/step] 2-614-037 Wide Roller:PaperTransfer:Standard:
1Sid:S5
2-614-038 Wide Roller:PaperTransfer:Standard:
2Sid:S5
ENG [1 to 110 / 29 / 1/step]
291
292
3. Engine SP Mode Tables
2-614-039 Wide Roller:PaperTransfer:Low:1Side:S5 ENG [1 to 110 / 24 / 1/step]
2-614-040 Wide Roller:PaperTransfer:Low:2Side:S5 ENG [1 to 110 / 29 / 1/step]
2615 [Special3:LeadingEdgeCorrection]
2-615-001 Paper Transfer:standard:1side
2-615-002 Paper Transfer:standard:2side
2-615-003 Paper Transfer:Low:1side
2-615-004 Paper Transfer:Low:2side
ENG
ENG
ENG
ENG
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
2616 [Special3:SwitchTimingLeadEdge]
2-616-001 Paper Transfer:standard:1side
2-616-002 Paper Transfer:standard:2side
2-616-003 Paper Transfer:Low:1side
2-616-004 Paper Transfer:Low:2side
2617 [Special3:TrailEdgeCorrection]
2-617-001 Paper Transfer:standard:1side
2-617-002 Paper Transfer:standard:2side
2-617-003 Paper Transfer:Low:1side
2-617-004 Paper Transfer:Low:2side
ENG
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG
ENG
ENG
ENG
ENG
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
2618 [Special3:SwitchTimingTrailEdge]
2-618-001 Paper Transfer:standard:1side
2-618-002 Paper Transfer:standard:2side
2-618-003 Paper Transfer:Low:1side
2-618-004 Paper Transfer:Low:2side
2623 [Special1 Thick:Bias:BW]
ENG
ENG
ENG
ENG
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
Engine SP Tables - SP2000-2
2-623-003 PaperTransfer:1side
2-623-004 PaperTransfer:2side
2627 [Special1 Thick:Bias:FC]
2-627-003 PaperTransfer:1side
2-627-004 PaperTransfer:2side
2631 [Special1Thick:PaperSizeCorr:BW]
2-631-003 PaperTransfer:1Side:S1
2-631-004 PaperTransfer:2Side:S1
2-631-007 PaperTransfer:1Side:S2
2-631-008 PaperTransfer:2Side:S2
2-631-011 PaperTransfer:1Side:S3
2-631-012 PaperTransfer:2Side:S3
2-631-015 PaperTransfer:1Side:S4
2-631-016 PaperTransfer:2Side:S4
2-631-019 PaperTransfer:1Side:S5
2-631-020 PaperTransfer:2Side:S5
2-631-023 Wide Roller:PaperTransfer:1Side:S1
ENG [0 to 200 / 11 / 1-uA/step]
ENG [0 to 200 / 15 / 1-uA/step]
ENG [0 to 200 / 19 / 1-uA/step]
ENG [0 to 200 / 21 / 1-uA/step]
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 133 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 167 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 233 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 267 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
293
294
3. Engine SP Mode Tables
2-631-024 Wide Roller:PaperTransfer:2Side:S1
2-631-027 Wide Roller:PaperTransfer:1Side:S2
2-631-028 Wide Roller:PaperTransfer:2Side:S2
2-631-031 Wide Roller:PaperTransfer:1Side:S3
2-631-032 Wide Roller:PaperTransfer:2Side:S3
2-631-035 Wide Roller:PaperTransfer:1Side:S4
2-631-036 Wide Roller:PaperTransfer:2Side:S4
2-631-039 Wide Roller:PaperTransfer:1Side:S5
2-631-040 Wide Roller:PaperTransfer:2Side:S5
2632 [Special1Thick:PaperSizeCorr:FC]
2-632-003 PaperTransfer:1Side:S1
2-632-004 PaperTransfer:2Side:S1
2-632-007 PaperTransfer:1Side:S2
2-632-008 PaperTransfer:2Side:S2
2-632-011 PaperTransfer:1Side:S3
2-632-012 PaperTransfer:2Side:S3
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 133 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 167 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 233 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 267 / 1%/ step]
ENG
ENG
ENG
ENG
ENG
ENG
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 181 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 229 / 1%/ step]
Engine SP Tables - SP2000-2
2-632-015 PaperTransfer:1Side:S4
2-632-016 PaperTransfer:2Side:S4
2-632-019 PaperTransfer:1Side:S5
2-632-020 PaperTransfer:2Side:S5
2-632-023 Wide Roller:PaperTransfer:1Side:S1
2-632-024 Wide Roller:PaperTransfer:2Side:S1
2-632-027 Wide Roller:PaperTransfer:1Side:S2
2-632-028 Wide Roller:PaperTransfer:2Side:S2
2-632-031 Wide Roller:PaperTransfer:1Side:S3
2-632-032 Wide Roller:PaperTransfer:2Side:S3
2-632-035 Wide Roller:PaperTransfer:1Side:S4
2-632-036 Wide Roller:PaperTransfer:2Side:S4
2-632-039 Wide Roller:PaperTransfer:1Side:S5
2-632-040 Wide Roller:PaperTransfer:2Side:S5
2633 [Sp1Thick:PaperSizeEnvCorr:BW]
2-633-003 PaperTransfer:1Side:S1
2-633-004 PaperTransfer:2Side:S1
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 286 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 381 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 181 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 229 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 286 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 381 / 1%/ step]
ENG [1 to 110 / 85 / 1/step]
ENG [1 to 110 / 87 / 1/step]
295
296
3. Engine SP Mode Tables
2-633-007 PaperTransfer:1Side:S2
2-633-008 PaperTransfer:2Side:S2
2-633-011 PaperTransfer:1Side:S3
2-633-012 PaperTransfer:2Side:S3
2-633-015 PaperTransfer:1Side:S4
2-633-016 PaperTransfer:2Side:S4
2-633-019 PaperTransfer:1Side:S5
2-633-020 PaperTransfer:2Side:S5
2-633-023 Wide Roller:PaperTransfer:1Side:S1
2-633-024 Wide Roller:PaperTransfer:2Side:S1
2-633-027 Wide Roller:PaperTransfer:1Side:S2
2-633-028 Wide Roller:PaperTransfer:2Side:S2
2-633-031 Wide Roller:PaperTransfer:1Side:S3
2-633-032 Wide Roller:PaperTransfer:2Side:S3
2-633-035 Wide Roller:PaperTransfer:1Side:S4
2-633-036 Wide Roller:PaperTransfer:2Side:S4
2-633-039 Wide Roller:PaperTransfer:1Side:S5
2-633-040 Wide Roller:PaperTransfer:2Side:S5
2634 [Sp1Thick:PaperSizeEnvCorr:FC]
2-634-003 PaperTransfer:1Side:S1
2-634-004 PaperTransfer:2Side:S1
2-634-007 PaperTransfer:1Side:S2
2-634-008 PaperTransfer:2Side:S2
2-634-011 PaperTransfer:1Side:S3
2-634-012 PaperTransfer:2Side:S3
ENG [1 to 110 / 86 / 1/step]
ENG [1 to 110 / 88 / 1/step]
ENG [1 to 110 / 86 / 1/step]
ENG [1 to 110 / 89 / 1/step]
ENG [1 to 110 / 86 / 1/step]
ENG [1 to 110 / 90 / 1/step]
ENG [1 to 110 / 86 / 1/step]
ENG [1 to 110 / 91 / 1/step]
ENG [1 to 110 / 85 / 1/step]
ENG [1 to 110 / 87 / 1/step]
ENG [1 to 110 / 86 / 1/step]
ENG [1 to 110 / 88 / 1/step]
ENG [1 to 110 / 86 / 1/step]
ENG [1 to 110 / 89 / 1/step]
ENG [1 to 110 / 86 / 1/step]
ENG [1 to 110 / 90 / 1/step]
ENG [1 to 110 / 86 / 1/step]
ENG [1 to 110 / 91 / 1/step]
ENG [1 to 110 / 77 / 1/step]
ENG [1 to 110 / 92 / 1/step]
ENG [1 to 110 / 78 / 1/step]
ENG [1 to 110 / 93 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 94 / 1/step]
Engine SP Tables - SP2000-2
2-634-015 PaperTransfer:1Side:S4
2-634-016 PaperTransfer:2Side:S4
2-634-019 PaperTransfer:1Side:S5
2-634-020 PaperTransfer:2Side:S5
2-634-023 Wide Roller:PaperTransfer:1Side:S1
2-634-024 Wide Roller:PaperTransfer:2Side:S1
2-634-027 Wide Roller:PaperTransfer:1Side:S2
2-634-028 Wide Roller:PaperTransfer:2Side:S2
2-634-031 Wide Roller:PaperTransfer:1Side:S3
2-634-032 Wide Roller:PaperTransfer:2Side:S3
2-634-035 Wide Roller:PaperTransfer:1Side:S4
2-634-036 Wide Roller:PaperTransfer:2Side:S4
2-634-039 Wide Roller:PaperTransfer:1Side:S5
2-634-040 Wide Roller:PaperTransfer:2Side:S5
2635 [Sp1Thick:LeadingEdgeCorrection]
2-635-003 Paper Transfer:1side
2-635-004 Paper Transfer:2side
2636 [Sp1Thick:SwitchTimingLeadEdge]
2-636-003 Paper Transfer:1side
2-636-004 Paper Transfer:2side
2637 [Sp1Thick:TrailEdgeCorrection]
2-637-003 Paper Transfer:1side
2-637-004 Paper Transfer:2side
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 95 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 96 / 1/step]
ENG [1 to 110 / 77 / 1/step]
ENG [1 to 110 / 92 / 1/step]
ENG [1 to 110 / 78 / 1/step]
ENG [1 to 110 / 93 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 94 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 95 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 96 / 1/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
297
298
3. Engine SP Mode Tables
2638 [Sp1Thick:SwitchTimingTrailEdge]
2-638-003 Paper Transfer:1side
2-638-004 Paper Transfer:2side
2643 [Special2 Thick:Bias:BW]
2-643-003 PaperTransfer:1side
2-643-004 PaperTransfer:2side
2647 [Special2 Thick:Bias:FC]
2-647-003 PaperTransfer:1side
2-647-004 PaperTransfer:2side
2651 [Special2Thick:PaperSizeCorr:BW]
2-651-003 PaperTransfer:1Side:S1
2-651-004 PaperTransfer:2Side:S1
2-651-007 PaperTransfer:1Side:S2
2-651-008 PaperTransfer:2Side:S2
2-651-011 PaperTransfer:1Side:S3
2-651-012 PaperTransfer:2Side:S3
2-651-015 PaperTransfer:1Side:S4
2-651-016 PaperTransfer:2Side:S4
2-651-019 PaperTransfer:1Side:S5
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 200 / 11 / 1-uA/step]
ENG [0 to 200 / 15 / 1-uA/step]
ENG [0 to 200 / 19 / 1-uA/step]
ENG [0 to 200 / 21 / 1-uA/step]
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 133 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 167 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 233 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
Engine SP Tables - SP2000-2
2-651-020 PaperTransfer:2Side:S5
2-651-023 Wide Roller:PaperTransfer:1Side:S1
2-651-024 Wide Roller:PaperTransfer:2Side:S1
2-651-027 Wide Roller:PaperTransfer:1Side:S2
2-651-028 Wide Roller:PaperTransfer:2Side:S2
2-651-031 Wide Roller:PaperTransfer:1Side:S3
2-651-032 Wide Roller:PaperTransfer:2Side:S3
2-651-035 Wide Roller:PaperTransfer:1Side:S4
2-651-036 Wide Roller:PaperTransfer:2Side:S4
2-651-039 Wide Roller:PaperTransfer:1Side:S5
2-651-040 Wide Roller:PaperTransfer:2Side:S5
2652 [Special2Thick:PaperSizeCorr:FC]
2-652-003 PaperTransfer:1Side:S1
2-652-004 PaperTransfer:2Side:S1
2-652-007 PaperTransfer:1Side:S2
2-652-008 PaperTransfer:2Side:S2
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[100 to 995 / 267 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 133 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 167 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 233 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 267 / 1%/ step]
ENG
ENG
ENG
ENG
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 181 / 1%/ step]
299
300
3. Engine SP Mode Tables
2-652-011 PaperTransfer:1Side:S3
2-652-012 PaperTransfer:2Side:S3
2-652-015 PaperTransfer:1Side:S4
2-652-016 PaperTransfer:2Side:S4
2-652-019 PaperTransfer:1Side:S5
2-652-020 PaperTransfer:2Side:S5
2-652-023 Wide Roller:PaperTransfer:1Side:S1
2-652-024 Wide Roller:PaperTransfer:2Side:S1
2-652-027 Wide Roller:PaperTransfer:1Side:S2
2-652-028 Wide Roller:PaperTransfer:2Side:S2
2-652-031 Wide Roller:PaperTransfer:1Side:S3
2-652-032 Wide Roller:PaperTransfer:2Side:S3
2-652-035 Wide Roller:PaperTransfer:1Side:S4
2-652-036 Wide Roller:PaperTransfer:2Side:S4
2-652-039 Wide Roller:PaperTransfer:1Side:S5
2-652-040 Wide Roller:PaperTransfer:2Side:S5
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 229 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 286 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 381 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 181 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 229 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 286 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 381 / 1%/ step]
Engine SP Tables - SP2000-2
2653 [Sp2Thick:PaperSizeEnvCorr:BW]
2-653-003 PaperTransfer:1Side:S1
2-653-004 PaperTransfer:2Side:S1
2-653-007 PaperTransfer:1Side:S2
2-653-008 PaperTransfer:2Side:S2
2-653-011 PaperTransfer:1Side:S3
2-653-012 PaperTransfer:2Side:S3
2-653-015 PaperTransfer:1Side:S4
2-653-016 PaperTransfer:2Side:S4
2-653-019 PaperTransfer:1Side:S5
2-653-020 PaperTransfer:2Side:S5
2-653-023 Wide Roller:PaperTransfer:1Side:S1
2-653-024 Wide Roller:PaperTransfer:2Side:S1
2-653-027 Wide Roller:PaperTransfer:1Side:S2
2-653-028 Wide Roller:PaperTransfer:2Side:S2
2-653-031 Wide Roller:PaperTransfer:1Side:S3
2-653-032 Wide Roller:PaperTransfer:2Side:S3
2-653-035 Wide Roller:PaperTransfer:1Side:S4
2-653-036 Wide Roller:PaperTransfer:2Side:S4
2-653-039 Wide Roller:PaperTransfer:1Side:S5
2-653-040 Wide Roller:PaperTransfer:2Side:S5
2654 [Sp2Thick:PaperSizeEnvCorr:FC]
2-654-003 PaperTransfer:1Side:S1
2-654-004 PaperTransfer:2Side:S1
2-654-007 PaperTransfer:1Side:S2
ENG [1 to 110 / 70 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 71 / 1/step]
ENG [1 to 110 / 73 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 74 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 75 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 76 / 1/step]
ENG [1 to 110 / 70 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 71 / 1/step]
ENG [1 to 110 / 73 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 74 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 75 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 76 / 1/step]
ENG [1 to 110 / 77 / 1/step]
ENG [1 to 110 / 80 / 1/step]
ENG [1 to 110 / 78 / 1/step]
301
302
3. Engine SP Mode Tables
2-654-008 PaperTransfer:2Side:S2
2-654-011 PaperTransfer:1Side:S3
2-654-012 PaperTransfer:2Side:S3
2-654-015 PaperTransfer:1Side:S4
2-654-016 PaperTransfer:2Side:S4
2-654-019 PaperTransfer:1Side:S5
2-654-020 PaperTransfer:2Side:S5
2-654-023 Wide Roller:PaperTransfer:1Side:S1
2-654-024 Wide Roller:PaperTransfer:2Side:S1
2-654-027 Wide Roller:PaperTransfer:1Side:S2
2-654-028 Wide Roller:PaperTransfer:2Side:S2
2-654-031 Wide Roller:PaperTransfer:1Side:S3
2-654-032 Wide Roller:PaperTransfer:2Side:S3
2-654-035 Wide Roller:PaperTransfer:1Side:S4
2-654-036 Wide Roller:PaperTransfer:2Side:S4
2-654-039 Wide Roller:PaperTransfer:1Side:S5
2-654-040 Wide Roller:PaperTransfer:2Side:S5
2655 [Sp2Thick:LeadingEdgeCorrection]
2-655-003 Paper Transfer:1side
2-655-004 Paper Transfer:2side
2656 [Sp2Thick:SwitchTimingLeadEdge]
2-656-003 Paper Transfer:1side
2-656-004 Paper Transfer:2side
2657 [Sp2Thick:TrailEdgeCorrection]
ENG [1 to 110 / 81 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 82 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 83 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 84 / 1/step]
ENG [1 to 110 / 77 / 1/step]
ENG [1 to 110 / 80 / 1/step]
ENG [1 to 110 / 78 / 1/step]
ENG [1 to 110 / 81 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 82 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 83 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 84 / 1/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
2-657-003 Paper Transfer:1side
2-657-004 Paper Transfer:2side
2658 [Sp2Thick:SwitchTimingTrailEdge]
2-658-003 Paper Transfer:1side
2-658-004 Paper Transfer:2side
2663 [Special3 Thick:Bias:BW]
2-663-003 PaperTransfer:1side
2-663-004 PaperTransfer:2side
2667 [Special3 Thick:Bias:FC]
2-667-003 PaperTransfer:1side
2-667-004 PaperTransfer:2side
2671 [Special3Thick:PaperSizeCorr:BW]
2-671-003 PaperTransfer:1Side:S1
2-671-004 PaperTransfer:2Side:S1
2-671-007 PaperTransfer:1Side:S2
2-671-008 PaperTransfer:2Side:S2
2-671-011 PaperTransfer:1Side:S3
2-671-012 PaperTransfer:2Side:S3
2-671-015 PaperTransfer:1Side:S4
ENG
ENG
Engine SP Tables - SP2000-2
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 200 / 11 / 1-uA/step]
ENG [0 to 200 / 15 / 1-uA/step]
ENG [0 to 200 / 19 / 1-uA/step]
ENG [0 to 200 / 21 / 1-uA/step]
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 133 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 167 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
303
304
3. Engine SP Mode Tables
2-671-016 PaperTransfer:2Side:S4
2-671-019 PaperTransfer:1Side:S5
2-671-020 PaperTransfer:2Side:S5
2-671-023 Wide Roller:PaperTransfer:1Side:S1
2-671-024 Wide Roller:PaperTransfer:2Side:S1
2-671-027 Wide Roller:PaperTransfer:1Side:S2
2-671-028 Wide Roller:PaperTransfer:2Side:S2
2-671-031 Wide Roller:PaperTransfer:1Side:S3
2-671-032 Wide Roller:PaperTransfer:2Side:S3
2-671-035 Wide Roller:PaperTransfer:1Side:S4
2-671-036 Wide Roller:PaperTransfer:2Side:S4
2-671-039 Wide Roller:PaperTransfer:1Side:S5
2-671-040 Wide Roller:PaperTransfer:2Side:S5
2672 [Special3Thick:PaperSizeCorr:FC]
2-672-003 PaperTransfer:1Side:S1
2-672-004 PaperTransfer:2Side:S1
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[100 to 995 / 233 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 267 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 133 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 167 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 233 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 267 / 5%/ step]
ENG
ENG
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
Engine SP Tables - SP2000-2
2-672-007 PaperTransfer:1Side:S2
2-672-008 PaperTransfer:2Side:S2
2-672-011 PaperTransfer:1Side:S3
2-672-012 PaperTransfer:2Side:S3
2-672-015 PaperTransfer:1Side:S4
2-672-016 PaperTransfer:2Side:S4
2-672-019 PaperTransfer:1Side:S5
2-672-020 PaperTransfer:2Side:S5
2-672-023 Wide Roller:PaperTransfer:1Side:S1
2-672-024 Wide Roller:PaperTransfer:2Side:S1
2-672-027 Wide Roller:PaperTransfer:1Side:S2
2-672-028 Wide Roller:PaperTransfer:2Side:S2
2-672-031 Wide Roller:PaperTransfer:1Side:S3
2-672-032 Wide Roller:PaperTransfer:2Side:S3
2-672-035 Wide Roller:PaperTransfer:1Side:S4
2-672-036 Wide Roller:PaperTransfer:2Side:S4
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 181 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 229 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 286 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 381 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 181 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 229 / 5%/ step]
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 286 / 5%/ step]
305
306
3. Engine SP Mode Tables
2-672-039 Wide Roller:PaperTransfer:1Side:S5
2-672-040 Wide Roller:PaperTransfer:2Side:S5
2673 [Sp3Thick:PaperSizeEnvCorr:BW]
2-673-003 PaperTransfer:1Side:S1
2-673-004 PaperTransfer:2Side:S1
2-673-007 PaperTransfer:1Side:S2
2-673-008 PaperTransfer:2Side:S2
2-673-011 PaperTransfer:1Side:S3
2-673-012 PaperTransfer:2Side:S3
2-673-015 PaperTransfer:1Side:S4
2-673-016 PaperTransfer:2Side:S4
2-673-019 PaperTransfer:1Side:S5
2-673-020 PaperTransfer:2Side:S5
2-673-023 Wide Roller:PaperTransfer:1Side:S1
2-673-024 Wide Roller:PaperTransfer:2Side:S1
2-673-027 Wide Roller:PaperTransfer:1Side:S2
2-673-028 Wide Roller:PaperTransfer:2Side:S2
2-673-031 Wide Roller:PaperTransfer:1Side:S3
2-673-032 Wide Roller:PaperTransfer:2Side:S3
2-673-035 Wide Roller:PaperTransfer:1Side:S4
2-673-036 Wide Roller:PaperTransfer:2Side:S4
2-673-039 Wide Roller:PaperTransfer:1Side:S5
2-673-040 Wide Roller:PaperTransfer:2Side:S5
ENG
ENG
[100 to 995 / 100 / 5%/ step]
[100 to 995 / 381 / 5%/ step]
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[1 to 110 / 70 / 1/step]
[1 to 110 / 72 / 1/step]
[1 to 110 / 71 / 1/step]
[1 to 110 / 73 / 1/step]
[1 to 110 / 72 / 1/step]
[1 to 110 / 74 / 1/step]
[1 to 110 / 72 / 1/step]
[1 to 110 / 75 / 1/step]
[1 to 110 / 72 / 1/step]
[1 to 110 / 76 / 1/step]
[1 to 110 / 70 / 1/step]
[1 to 110 / 72 / 1/step]
[1 to 110 / 71 / 1/step]
ENG [1 to 110 / 73 / 1/step]
ENG [1 to 110 / 72 / 1/step]
[1 to 110 / 74 / 1/step]
[1 to 110 / 72 / 1/step]
[1 to 110 / 75 / 1/step]
[1 to 110 / 72 / 1/step]
[1 to 110 / 76 / 1/step]
Engine SP Tables - SP2000-2
2674 [Sp3Thick:PaperSizeEnvCorr:FC]
2-674-003 PaperTransfer:1Side:S1
2-674-004 PaperTransfer:2Side:S1
2-674-007 PaperTransfer:1Side:S2
2-674-008 PaperTransfer:2Side:S2
2-674-011 PaperTransfer:1Side:S3
2-674-012 PaperTransfer:2Side:S3
2-674-015 PaperTransfer:1Side:S4
2-674-016 PaperTransfer:2Side:S4
2-674-019 PaperTransfer:1Side:S5
2-674-020 PaperTransfer:2Side:S5
2-674-023 Wide Roller:PaperTransfer:1Side:S1
2-674-024 Wide Roller:PaperTransfer:2Side:S1
2-674-027 Wide Roller:PaperTransfer:1Side:S2
2-674-028 Wide Roller:PaperTransfer:2Side:S2
2-674-031 Wide Roller:PaperTransfer:1Side:S3
2-674-032 Wide Roller:PaperTransfer:2Side:S3
2-674-035 Wide Roller:PaperTransfer:1Side:S4
2-674-036 Wide Roller:PaperTransfer:2Side:S4
2-674-039 Wide Roller:PaperTransfer:1Side:S5
2-674-040 Wide Roller:PaperTransfer:2Side:S5
2675 [Sp3Thick:LeadingEdgeCorrection]
2-675-003 Paper Transfer:1side
2-675-004 Paper Transfer:2side
2676 [Sp3Thick:SwitchTimingLeadEdge]
ENG [1 to 110 / 77 / 1/step]
ENG [1 to 110 / 80 / 1/step]
ENG [1 to 110 / 78 / 1/step]
ENG [1 to 110 / 81 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 82 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 83 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 84 / 1/step]
ENG [1 to 110 / 77 / 1/step]
ENG [1 to 110 / 80 / 1/step]
ENG [1 to 110 / 78 / 1/step]
ENG [1 to 110 / 81 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 82 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 83 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 84 / 1/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
307
308
3. Engine SP Mode Tables
2-675-003 Paper Transfer:1side
2-675-004 Paper Transfer:2side
2677 [Sp3Thick:TrailEdgeCorrection]
2-675-003 Paper Transfer:1side
2-675-004 Paper Transfer:2side
2678 [Sp3Thick:SwitchTimingTrailEdge]
2-678-003 Paper Transfer:1side
2-678-004 Paper Transfer:2side
2690 [ITB Contact Setting]
2-690-001 Thick1
2-690-002 Thick2
2-690-003 Thick3
2-690-004 Thick4
2-690-014 Special1Thick1234
2-690-015 Special2Thick1234
2-690-016 Special3Thick1234
2703 [Thick4:Bias:BW]
2-703-003 PaperTransfer:1side
2-703-004 PaperTransfer:2side
2707 [Thick4:Bias:FC]
2-707-003 PaperTransfer:1side
2-707-004 PaperTransfer:2side
2711 [Thick4:SizeCorrection:BW]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 to 50 / 0 / 2mm/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 to 200 / 11 / 1-uA/step]
ENG [0 to 200 / 15 / 1-uA/step]
ENG [0 to 200 / 19 / 1-uA/step]
ENG [0 to 200 / 21 / 1-uA/step]
Engine SP Tables - SP2000-2
2-711-003 PaperTransfer:1Side:S1
2-711-004 PaperTransfer:2Side:S1
2-711-007 PaperTransfer:1Side:S2
2-711-008 PaperTransfer:2Side:S2
2-711-011 PaperTransfer:1Side:S3
2-711-012 PaperTransfer:2Side:S3
2-711-015 PaperTransfer:1Side:S4
2-711-016 PaperTransfer:2Side:S4
2-711-019 PaperTransfer:1Side:S5
2-711-020 PaperTransfer:2Side:S5
2-711-023 Wide Roller:PaperTransfer:1Side:S1
2-711-024 Wide Roller:PaperTransfer:2Side:S1
2-711-027 Wide Roller:PaperTransfer:1Side:S2
2-711-028 Wide Roller:PaperTransfer:2Side:S2
2-711-031 Wide Roller:PaperTransfer:1Side:S3
2-711-032 Wide Roller:PaperTransfer:2Side:S3
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 133 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 167 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 233 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 267 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 133 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 167 / 1%/ step]
309
310
3. Engine SP Mode Tables
2-711-035 Wide Roller:PaperTransfer:1Side:S4
2-711-036 Wide Roller:PaperTransfer:2Side:S4
2-711-039 Wide Roller:PaperTransfer:1Side:S5
2-711-040 Wide Roller:PaperTransfer:2Side:S5
2712 [Thick4:SizeCorrection:FC]
2-712-003 PaperTransfer:1Side:S1
2-712-004 PaperTransfer:2Side:S1
2-712-007 PaperTransfer:1Side:S2
2-712-008 PaperTransfer:2Side:S2
2-712-011 PaperTransfer:1Side:S3
2-712-012 PaperTransfer:2Side:S3
2-712-015 PaperTransfer:1Side:S4
2-712-016 PaperTransfer:2Side:S4
2-712-019 PaperTransfer:1Side:S5
2-712-020 PaperTransfer:2Side:S5
2-712-023 Wide Roller:PaperTransfer:1Side:S1
ENG
ENG
ENG
ENG
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 233 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 267 / 1%/ step]
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 181 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 229 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 286 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 381 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
Engine SP Tables - SP2000-2
2-712-024 Wide Roller:PaperTransfer:2Side:S1
2-712-027 Wide Roller:PaperTransfer:1Side:S2
2-712-028 Wide Roller:PaperTransfer:2Side:S2
2-712-031 Wide Roller:PaperTransfer:1Side:S3
2-712-032 Wide Roller:PaperTransfer:2Side:S3
2-712-035 Wide Roller:PaperTransfer:1Side:S4
2-712-036 Wide Roller:PaperTransfer:2Side:S4
2-712-039 Wide Roller:PaperTransfer:1Side:S5
2-712-040 Wide Roller:PaperTransfer:2Side:S5
2713 [Thick4:Size-Env.Correct:BW]
2-713-003 PaperTransfer:1Side:S1
2-713-004 PaperTransfer:2Side:S1
2-713-007 PaperTransfer:1Side:S2
2-713-008 PaperTransfer:2Side:S2
2-713-011 PaperTransfer:1Side:S3
2-713-012 PaperTransfer:2Side:S3
2-713-015 PaperTransfer:1Side:S4
2-713-016 PaperTransfer:2Side:S4
2-713-019 PaperTransfer:1Side:S5
2-713-020 PaperTransfer:2Side:S5
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 181 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 229 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 286 / 1%/ step]
[100 to 995 / 100 / 1%/ step]
[100 to 995 / 381 / 1%/ step]
ENG [1 to 110 / 70 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 71 / 1/step]
ENG [1 to 110 / 73 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 74 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 75 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 76 / 1/step]
311
312
3. Engine SP Mode Tables
2-713-023 Wide Roller:PaperTransfer:1Side:S1
2-713-024 Wide Roller:PaperTransfer:2Side:S1
2-713-027 Wide Roller:PaperTransfer:1Side:S2
2-713-028 Wide Roller:PaperTransfer:2Side:S2
2-713-031 Wide Roller:PaperTransfer:1Side:S3
2-713-032 Wide Roller:PaperTransfer:2Side:S3
2-713-035 Wide Roller:PaperTransfer:1Side:S4
2-713-036 Wide Roller:PaperTransfer:2Side:S4
2-713-039 Wide Roller:PaperTransfer:1Side:S5
2-713-040 Wide Roller:PaperTransfer:2Side:S5
2714 [Thick4:Size-Env.Correct:FC]
2-714-003 PaperTransfer:1Side:S1
2-714-004 PaperTransfer:2Side:S1
2-714-007 PaperTransfer:1Side:S2
2-714-008 PaperTransfer:2Side:S2
2-714-011 PaperTransfer:1Side:S3
2-714-012 PaperTransfer:2Side:S3
2-714-015 PaperTransfer:1Side:S4
2-714-016 PaperTransfer:2Side:S4
2-714-019 PaperTransfer:1Side:S5
2-714-020 PaperTransfer:2Side:S5
2-714-023 Wide Roller:PaperTransfer:1Side:S1
2-714-024 Wide Roller:PaperTransfer:2Side:S1
2-714-027 Wide Roller:PaperTransfer:1Side:S2
2-714-028 Wide Roller:PaperTransfer:2Side:S2
ENG [1 to 110 / 70 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 71 / 1/step]
ENG [1 to 110 / 73 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 74 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 75 / 1/step]
ENG [1 to 110 / 72 / 1/step]
ENG [1 to 110 / 76 / 1/step]
ENG [1 to 110 / 77 / 1/step]
ENG [1 to 110 / 80 / 1/step]
ENG [1 to 110 / 78 / 1/step]
ENG [1 to 110 / 81 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 82 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 83 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 84 / 1/step]
ENG [1 to 110 / 77 / 1/step]
ENG [1 to 110 / 80 / 1/step]
ENG [1 to 110 / 78 / 1/step]
ENG [1 to 110 / 81 / 1/step]
Engine SP Tables - SP2000-2
2-714-031 Wide Roller:PaperTransfer:1Side:S3
2-714-032 Wide Roller:PaperTransfer:2Side:S3
2-714-035 Wide Roller:PaperTransfer:1Side:S4
2-714-036 Wide Roller:PaperTransfer:2Side:S4
2-714-039 Wide Roller:PaperTransfer:1Side:S5
2-714-040 Wide Roller:PaperTransfer:2Side:S5
2715 [Thick4:LeadingEdgeCorrection]
2-715-003 Paper Transfer:1side
2-715-004 Paper Transfer:2side
2716 [Thick4:SwitchTimingLeadEdge]
2-716-003 Paper Transfer:1side
2-716-004 Paper Transfer:2side
2717 [Thick4:TrailEdgeCorrection]
2-717-003 Paper Transfer:1side
2-717-004 Paper Transfer:2side
ENG
ENG
ENG
ENG
ENG
[1 to 110 / 79 / 1/step]
ENG [1 to 110 / 82 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 83 / 1/step]
ENG [1 to 110 / 79 / 1/step]
ENG [1 to 110 / 84 / 1/step]
[0 to 995 / 100 / 5%/step]
[0 to 995 / 100 / 5%/step]
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
ENG [0 to 995 / 100 / 5%/step]
ENG [0 to 995 / 100 / 5%/step]
2718 [Thick4:SwitchTimingTrailEdge]
2-718-003 Paper Transfer:1side
2-718-004 Paper Transfer:2side
2901 [OPC Drum Brake Time]
2-901-001 All
2902 [OPC Drum Reverse Time]
2-902-001 All: BW
ENG
ENG
[0 to 50 / 0 / 2mm/step]
[0 to 50 / 0 / 2mm/step]
*ENG [50 to 240000 / 50 / 10msec/step]
*ENG [0 to 200 / 40 / 10msec/step]
313
314
3. Engine SP Mode Tables
2-902-002 All: FC
2903 [Image Transfer Brake Time]
2-903-003 All
2905 [Dev Rvs Time]
2-905-003 K
2-905-004 Cl
2905 [Dev Rvs Threshold Counter]
2-905-005 ALL
2905 [Dev Rvs Counter]
2-905-006 K
2-905-007 Cl
*ENG
*ENG
*ENG
*ENG
*ENG
[0 to 200 / 40 / 10msec/step]
[50 to 240000 / 50 / 10msec/step]
[0 to 200 / 70 / 10msec/step]
[0 to 200 / 90 / 10msec/step]
[0 to 400000 / 4000 / 10mm/step]
*ENG [0 to 4294967295 / 0 / 1mm/step]
*ENG [0 to 4294967295 / 0 / 1mm/step]
2907 [ACS Setting (FC to Bk)]
2-907-001 Continuous Bk Pages
2930 [Transfer:Bias Limiter]
2-930-001 Bias
*ENG [0 to 10 / 0 / 1sheet/step]
*ENG [0 to 7000 / 6000 / 10-V/step]
2960 [Process Interval]
2-960-001 Additional Time
2972 [B/W Image Request Timing]
2-972-001 T14:standard speed
2-972-003 T14:low speed
2974 [Trans. Contact Fgate Timing: Y]
*ENG [0 to 10 / 0 / 1sec/step]
*ENG [0 to 4000 / 0 / 10msec/step]
*ENG
Engine SP Tables - SP2000-2
2-974-001 Fwait:Y std
2-974-002 Fwait:Y mid
2-974-003 Fwait:Y low
*ENG [0 to 3000 / 0 / 10msec/step]
*ENG
*ENG
2980 [LubricantApplication Operation]
2-980-001 Lubricant Application Setting *ENG [0 to 300 / 0 / 10pages/step]
2-980-002 Idle Time: BK
2-980-003 Idle Time: FC
*ENG [0 to 600 / 1 / 1sec/step]
*ENG [0 to 600 / 1 / 1sec/step]
2990 [Print Duty Control]
2-990-001 Duty Control State
2-990-002 Exec Interval: Duty Control
2-990-004 Forced CPM Down Thresh: No
Duty Control
2-990-005 Down-time_BW: No Duty
Control
2-990-006 Down-time_FC: No Duty
Control
*ENG [0 or 1 / 0 / 1/step]
0: Non restricted
1: Restricted
*ENG
*ENG
*ENG
*ENG
[60 to 3600 / 60 / 10sec/step]
[0 to 5000 / 0 / 1page/step]
[0 to 20000 / 0 / 10msec/step]
[0 to 20000 / 0 / 10msec/step]
2-990-007 Forced CPM Down Thresh:
Duty Control
2-990-008 Down-time_BW: Duty Control
*ENG [0 to 5000 / 20 / 1page/step]
2-990-009 Down-time_FC: Duty Control
*ENG [0 to 240000 / 60000 / 10msec/ step]
*ENG [0 to 240000 / 60000 / 10msec/ step]
2-990-010 Ambient Temp Correction Coeff *ENG [-1 to 1 / 0 / 0.1/step]
2-990-011 Execution Temp. Threshold *ENG [20 to 70 / 38.5 / 0.1deg/step]
2-990-012 Cancellation Temp. Threshold *ENG [0.1 to 20 / 0.1 / 0.1deg/step]
315
316
3. Engine SP Mode Tables
2-990-013 ON/OFF Setting
2-990-014 Duty Control_Down-time_BW
2-990-015 Duty Control_Down-time_FC
*ENG [0 or 1 / 1 / 1/step]
*ENG [0 to 240000 / 0 / 10msec/step]
*ENG [0 to 240000 / 0 / 10msec/step]
Engine SP Tables - SP3000
3011 [Manual ProCon :Exe]
3-011-001 Normal ProCon
3-011-002 Density Adjustment
3-011-003 ACC RunTime ProCon
3-011-004 Full MUSIC
3-011-005 Normal MUSIC
ENG [0 or 1 / 0 / 1/step]
[Execute]
ENG [0 or 1 / 0 / 1/step]
[Execute]
ENG [0 or 1 / 0 / 1/step]
[Execute]
ENG [0 or 1 / 0 / 1/step]
[Execute]
ENG [0 or 1 / 0 / 1/step]
[Execute]
3012 [ProCon OK?]
3-012-001 History:Last(Front)
3-012-002 History:Last 2(Front)
3-012-003 History:Last 3(Front)
3-012-004 History:Last 4(Front)
3-012-005 History:Last 5(Front)
3-012-006 History:Last 6(Front)
3-012-007 History:Last 7(Front)
3-012-008 History:Last 8(Front)
3-012-009 History:Last 9(Front)
3-012-010 History:Last 10(Front)
3-012-011 History:Last(Center)
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
317
318
3. Engine SP Mode Tables
3-012-012 History:Last 2(Center)
3-012-013 History:Last 3(Center)
3-012-014 History:Last 4(Center)
3-012-015 History:Last 5(Center)
3-012-016 History:Last 6(Center)
3-012-017 History:Last 7(Center)
3-012-018 History:Last 8(Center)
3-012-019 History:Last 9(Center)
3-012-020 History:Last 10(Center)
3-012-021 History:Last(Rear)
3-012-022 History:Last 2(Rear)
3-012-023 History:Last 3(Rear)
3-012-024 History:Last 4(Rear)
3-012-025 History:Last 5(Rear)
3-012-026 History:Last 6(Rear)
3-012-027 History:Last 7(Rear)
3-012-028 History:Last 8(Rear)
3-012-029 History:Last 9(Rear)
3-012-030 History:Last 10(Rear)
*SP3-012 Display result detail
Category
00 and larger
Code Result name
00 Not executed
10 and larger
Result (Normal)
11 Succeeded
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
-
Description
Factory default setting (SP default)
Engine SP Tables - SP3000
Category
40 and larger
ID Sensor
45 and larger
ID Pattern detection
90 and larger
Result(End)
Code Result name
41 ID sensor output error (Max)
42 ID sensor output error (Min)
43
44
ID Sensor error (Max)
ID Sensor error (Min)
Cannot detect ID Pattern
K:Vmin_Bk / CMY:K2 > Max
K:Vmin_Bk / CMY:K2 < Min
K5 > Max
Description
Vt > Max
Vt < Min
Development gamma is in target, but Vt value is less than upper limit.
Development gamma is in target, but Vt value is less than lower limit.
45 ID Pattern extract error
50 Vmin_Bk/K2 error (Max)
51 Vmin_Bk/K2 error (Min)
52 K5 error (Max)
53 K5 error (Min)
54
K5 calculated approximate point error
55
Development gamma error
(Max)
Development gamma > Max
56 Development gamma error (Min) Development gamma < Min
57
58
Start developing voltage: Vk error(Max)
Start developing voltage: Vk error(Min)
K5 < Min
K5 calculated approximate point <
Min
Start developing voltage: Vk >
Max
Start developing voltage: Vk < Min
59
90
99
Not enough valid data
Potential not adjusted
Stopped
Adhesion amount data for development gamma calculation point is under 2
Potential control method is set as
[0:FIX]
Stopped by door open, power off, error.
(Set when execute.)
319
320
3. Engine SP Mode Tables
• Execute result sample (In order of YMCK from left)
• Factory default(SP default):[00,00,00,00]
• Starting adjust:[99,99,99,99]
• Fail Vsg adjust(Y):[21,99,99,99]
• Error of Develop gamma Max(C):[99,99,55,99]
• Succeed:[11,11,11,11]
3014 [IBACC OK?]
3-014-001 History:Last
3-014-002 History:Last 2
3-014-003 History:Last 3
3-014-004 History:Last 4
3-014-005 History:Last 5
3-014-006 History:Last 6
3-014-007 History:Last 7
3-014-008 History:Last 8
3-014-009 History:Last 9
3-014-010 History:Last 10
*ENG [0 to 9999 / 0 / 1/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
3015 [Background Pot ProCon OK?]
3-015-001 History:Front:Latest
3-015-002 History:Front:Last 2
3-015-003 History:Front:Last 3
3-015-004 History:Front:Last 4
3-015-005 History:Front:Last 5
3-015-006 history:Center:Latest
3-015-007 History:Center:Last 2
*ENG [0 to 9999 / 0 / 1/step]
*ENG [0 to 9999 / 0 / 1/step]
*ENG [0 to 9999 / 0 / 1/step]
*ENG [0 to 9999 / 0 / 1/step]
*ENG [0 to 9999 / 0 / 1/step]
*ENG [0 to 9999 / 0 / 1/step]
*ENG [0 to 9999 / 0 / 1/step]
3-015-008 History:Center:Last 3
3-015-009 History:Center:Last 4
3-015-010 History:Center:Last 5
3-015-011 history:Rear:Latest
3-015-012 History:Rear:Last 2
3-015-013 History:Rear:Last 3
3-015-014 History:Rear:Last 4
3-015-015 History:Rear:Last 5
3030 [Init TD Sensor :Exe]
3-030-001 Execute: ALL
3-030-002 Execute: Col
3-030-003 Execute: K
3-030-004 Execute: C
3-030-005 Execute: M
3-030-006 Execute: Y
3-030-071 Init Temp: K
3-030-072 Init Temp: C
3-030-073 Init Temp: M
3-030-074 Init Temp: Y
3-030-081 Init Rel Hum: K
Engine SP Tables - SP3000
*ENG [0 to 9999 / 0 / 1/step]
*ENG [0 to 9999 / 0 / 1/step]
*ENG [0 to 9999 / 0 / 1/step]
*ENG [0 to 9999 / 0 / 1/step]
*ENG [0 to 9999 / 0 / 1/step]
*ENG [0 to 9999 / 0 / 1/step]
*ENG [0 to 9999 / 0 / 1/step]
*ENG [0 to 9999 / 0 / 1/step]
ENG
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[Execute]
[0 or 1 / 0 / 1/step]
[Execute]
[0 or 1 / 0 / 1/step]
[Execute]
[0 or 1 / 0 / 1/step]
[Execute]
ENG
ENG
[0 or 1 / 0 / 1/step]
[Execute]
[0 or 1 / 0 / 1/step]
[Execute]
*ENG [-100 to 100 / 23 / 0.1deg/step]
*ENG [-100 to 100 / 23 / 0.1deg/step]
*ENG [-100 to 100 / 23 / 0.1deg/step]
*ENG [-100 to 100 / 23 / 0.1deg/step]
*ENG [0 to 100 / 50 / 0.1%RH/step]
321
322
3. Engine SP Mode Tables
3-030-082 Init Rel Hum: C
3-030-083 Init Rel Hum: M
3-030-084 Init Rel Hum: Y
3-030-091 Init Abs Hum: K
3-030-092 Init Abs Hum: C
3-030-093 Init Abs Hum: M
3-030-094 Init Abs Hum: Y
3031 [TD Sens Init OK?]
3-031-001 From Left:YMCK
3050 [Force Tnr Supply :Exe]
3-050-001 Execute: ALL
3-050-002 Execute: Col
3-050-003 Execute: K
3-050-004 Execute: C
3-050-005 Execute: M
3-050-006 Execute: Y
3-050-021 Supply Quantity:K
3-050-022 Supply Quantity:C
3-050-023 Supply Quantity:M
3-050-024 Supply Quantity:Y
*ENG [0 to 100 / 50 / 0.1%RH/step]
*ENG [0 to 100 / 50 / 0.1%RH/step]
*ENG [0 to 100 / 50 / 0.1%RH/step]
*ENG [0 to 100 / 10.3 / 0.01g/m
3
/step]
*ENG [0 to 100 / 10.3 / 0.01g/m
3
/step]
*ENG [0 to 100 / 10.3 / 0.01g/m
3
/step]
*ENG [0 to 100 / 10.3 / 0.01g/m
3
/step]
ENG [0 to 9999 / 0 / 1/step]
ENG
ENG
ENG
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[Execute]
[0 or 1 / 0 / 1/step]
[Execute]
[0 or 1 / 0 / 1/step]
[Execute]
[0 or 1 / 0 / 1/step]
[Execute]
[0 or 1 / 0 / 1/step]
[Execute]
[0 or 1 / 0 / 1/step]
[Execute]
*ENG [0 to 5 / 0.5 / 0.1wt%/step]
*ENG [0 to 5 / 0.5 / 0.1wt%/step]
*ENG [0 to 5 / 0.5 / 0.1wt%/step]
*ENG [0 to 5 / 0.5 / 0.1wt%/step]
Engine SP Tables - SP3000
3-050-033 RepeatCount *ENG [0 to 255 / 8 / 1count/step]
3072 [T Sensor: Check]
3-072-001 Execute Check ENG [0 or 1 / 0 / 1/step]
[Execute]
3073 [T Sensor Measurement Value:]
3-073-001 mu count:K
3-073-002 mu count:C
3-073-003 mu count:M
3-073-004 mu count:Y
*ENG [0 to 65535 / 0 / 1/step]
*ENG
*ENG
*ENG
3100 [Tonner End Detection: Set]
3-100-001 ON/OFF
3-100-002 NE Detection
*ENG [0 or 1 / 0 / 1/step]
Whether to decide NE/TE.
0: Enable
1: Disable
*ENG [0 or 1 / 0 / 1/step]
NE decision method.
0: Counter & Toner End Sensor
1: Toner End Sensor Only
3101 [Toner Status :Disp]
3-101-001 K
3-101-002 C
3-101-003 M
3-101-004 Y
3102 [Toner Remain:Disp]
ENG
ENG
ENG
ENG
[0 to 10 / 10 / 1/step]
10: Full
1: Near end
0: Toner end
323
324
3. Engine SP Mode Tables
3-102-001 Bottle Motor: Bk
3-102-002 Bottle Motor: C
3-102-003 Bottle Motor: M
3-102-004 Bottle Motor: Y
3-102-011 Pixel: Bk
3-102-012 Pixel: C
3-102-013 Pixel: M
3-102-014 Pixel: Y
3102 [Toner Remaining: Display]
3-102-021 Fill Amount: Bk
3-102-022 Fill Amount: C
3-102-023 Fill Amount: M
3-102-024 Fill Amount: Y
3102 [Toner Remain:Disp]
*ENG [0.000 to 700.000 / 560.000 /
0.001g/step]
*ENG [0.000 to 700.000 / 440.000 /
0.001g/step]
*ENG
*ENG
*ENG [0.000 to 700.000 / 560.000 /
0.001g/step]
*ENG [0.000 to 700.000 / 440.000 /
0.001g/step]
*ENG
*ENG
*ENG [0 to 600 / 560 / 1g/step]
*ENG [0 to 600 / 440 / 1g/step]
*ENG
*ENG
Engine SP Tables - SP3000
3-102-031 Pixel: Toner Consumption x 2:
Bk
3-102-032 Pixel: Toner Consumption x 2:
C
3-102-033 Pixel: Toner Consumption x 2:
M
3-102-034 Pixel: Toner Consumption x 2:
Y
3-102-041 Drive Motor: Toner
Consumption x 1: Bk
3-102-042 Drive Motor: Toner
Consumption x 1: C
3-102-043 Drive Motor: Toner
Consumption x 1: M
3-102-044 Drive Motor: Toner
Consumption x 1: Y
3104 [Flag: Display]
3-104-001 NE Toner: Bk
3-104-002 NE Toner: C
3-104-003 NE Toner: M
3-104-004 NE Toner: Y
3-104-011 Vt end:Bk
3-104-012 Vt end:C
3-104-013 Vt end:M
3-104-014 Vt end:Y
3110 [Near End Thresh]
3-110-001 Bk
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[0.000 to 1000.000 / 0.000 /
0.001g/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
*ENG [0 to 500 / 65 / 1g/step]
325
326
3. Engine SP Mode Tables
3-110-002 C
3-110-003 M
3-110-004 Y
3121 [TE Counter: Disp]
3-121-001 Bk
3-121-002 C
3-121-003 M
3-121-004 Y
3121 [TE Counter: Clearcount]
3-121-011 Bk
3-121-012 C
3-121-013 M
3-121-014 Y
3131 [Vt TE Thresh]
3-131-001 Delta Vt Thresh
3-131-002 Delta Vt Sum Thresh
3-131-011 Delta Vt Thresh BF NE
3-131-012 Delta Vt Sum Thresh BF NE
3132 [Delta Vt Sum]
3-132-001 Bk
3-132-002 C
3-132-003 M
3-132-004 Y
*ENG
*ENG
*ENG
[0 to 500 / 45 / 1g/step]
*ENG [0 to 99 / 0 / 1count/step]
*ENG
*ENG
*ENG
*ENG [0 to 99 / 0 / 1count/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[0 to 5 / 0.5 / 0.01V/step]
[0 to 99 / 10 / 1V/step]
[0 to 5 / 0.5 / 0.01V/step]
[0 to 99 / 10 / 1V/step]
[0 to 99 / 0 / 0.01V/step]
Engine SP Tables - SP3000
3133 [TE Detect :Set]
3-133-001 Set Sheets(Min)
3-133-002 Set Sheets(Max)
3-133-011 Page Cnt:K
3-133-012 Page Cnt:C
3-133-013 Page Cnt:M
3-133-014 Page Cnt:Y
3-133-021 Set Pxl Cnt
3-133-031 Pxl Cnt:K
3-133-032 Pxl Cnt:C
3-133-033 Pxl Cnt:M
3-133-034 Pxl Cnt:Y
3150 [TE Sensor :Set]
3-150-001 SamplingCount
3-150-002 Judge:p
3-150-003 result:K
3-150-004 result:C
3-150-005 result:M
3-150-006 result:Y
3160 [Bottle Drive :Set]
3-160-001 Bottle Drive System
3200 [TnrDensity]
*ENG [0 to 50 / 10 / 1sheet/step]
*ENG [0 to 5000 / 1000 / 1sheet/step]
*ENG [0 to 5000 / 0 / 1sheet/step]
*ENG [0 to 5000 / 0 / 1sheet/step]
*ENG [0 to 5000 / 0 / 1sheet/step]
*ENG [0 to 5000 / 0 / 1sheet/step]
*ENG [0 to 1000000 / 7000 / 1cm
2
/step]
*ENG [0 to 1000000 / 0 / 1cm
2
/step]
*ENG [0 to 1000000 / 0 / 1cm
2
/step]
*ENG [0 to 1000000 / 0 / 1cm
2
/step]
*ENG [0 to 1000000 / 0 / 1cm
2
/step]
*ENG [4 to 20 / 10 / 1count/step
*ENG [0.2 to 1 / 0.8 / 0.1/step]
*ENG [0.0 to 1 / 0.5 / 0.1/step]
*ENG
*ENG
*ENG
*ENG [0 or 1 / 0 / 1/step]
0: TE Sensor Control
1: TonerSupplyMotor Track Control
327
328
3. Engine SP Mode Tables
3-200-001 K
3-200-002 C
3-200-003 M
3-200-004 Y
3201 [TnrDensity]
3-201-001 Upper TC
3-201-002 Lower TC
3205 [TD.Sens Sensitivity]
3-205-051 Mu Cnv Coef:K
3-205-052 Mu Cnv Coef:C
3-205-053 Mu Cnv Coef:M
3-205-054 Mu Cnv Coef:Y
3-205-101 Bulk Density: K
3-205-102 Bulk Density: C
3-205-103 Bulk Density: M
3-205-104 Bulk Density: Y
3210 [TD.Sens:Vt :Disp]
3-210-001 Current: K
3-210-002 Current: C
3-210-003 Current: M
3-210-004 Current: Y
3212 [Vt Shift :Set]
3-212-101 TC Cor.(ON/OFF)
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG [0.001 to 0.1 / 0.014 / 0.001V/count/step]
*ENG [0.001 to 0.1 / 0.016 / 0.001V/count/step]
*ENG [0.001 to 0.1 / 0.016 / 0.001V/count/step]
*ENG [0.001 to 0.1 / 0.016 / 0.001V/count/step]
*ENG [-5 to 5 / 0.00 / 0.01V/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[0 to 25.5 / 0.0 / 0.1wt%/step
[1.0 to 15.0 / 9.0 / 0.1wt%/step]
[-1.0 to 15.0 / 2.0 / 0.1wt%/step]
[0.00 to 5.50 / 0.00 / 0.01V/step]
[-0.5 to 0.5 / 0 / 0.01V/step]
3-212-111 TC Mid Spd:K
3-212-112 TC Mid Spd:C
3-212-113 TC Mid Spd:M
3-212-114 TC Mid Spd:Y
3-212-121 TC Low Spd:K
3-212-122 TC Low Spd:C
3-212-123 TC Low Spd:M
3-212-124 TC Low Spd:Y
3214 [Vt Save :Set]
3-214-001 Coverage Thresh
3230 [Vtref :Disp/Set]
3-230-001 Current: K
3-230-002 Current: C
3-230-003 Current: M
3-230-004 Current: Y
3232 [Vtref Correct:Pixel]
3-232-001 ON/OFF
3-232-011 Low Coverage Coef:K
3-232-012 Low Coverage Coef:C
3-232-013 Low Coverage Coef:M
3-232-014 Low Coverage Coef:Y
3-232-021 High Coverage Coeff:K
3-232-022 High Coverage Coeff:C
3-232-023 High Coverage Coeff:M
*ENG
*ENG
*ENG
*ENG
*ENG
Engine SP Tables - SP3000
[-0.5 to 0.5 / 0 / 0.01V/step]
*ENG [-0.5 to 0.5 / 0 / 0.01V/step]
*ENG [-0.5 to 0.5 / 0 / 0.01V/step]
*ENG [-0.5 to 0.5 / 0 / 0.01V/step]
[-0.5 to 0.5 / 0 / 0.01V/step]
[-0.5 to 0.5 / 0 / 0.01V/step]
[-0.5 to 0.5 / 0 / 0.01V/step]
[-0.5 to 0.5 / 0 / 0.01V/step]
*ENG [0 to 100 / 20 / 1 %/step
*ENG [0 to 5 / 1.8 / 0.01V/step]
*ENG [0 to 5 / 1.8 / 0.01V/step]
*ENG [0 to 5 / 1.8 / 0.01V/step]
*ENG [0 to 5 / 1.8 / 0.01V/step]
*ENG [0 or 1 / 1 / 1/step]
*ENG [0 to 5 / 1 / 0.1/step]
*ENG [0 to 5 / 1 / 0.1/step]
*ENG [0 to 5 / 1 / 0.1/step]
*ENG [0 to 5 / 1 / 0.1/step]
*ENG [0 to 5 / 0.5 / 0.1/step]
*ENG [0 to 5 / 1.0 / 0.1/step]
*ENG [0 to 5 / 1.0 / 0.1/step]
329
330
3. Engine SP Mode Tables
3-232-024 High Coverage Coeff:Y
3-232-040 Initial ProCon Thresh
3-232-041 High Coverage Thresh:H
3-232-050 ProCon Thresh
3-232-060 Low Coverage Thresh
3-232-070 TC Upper Limit Correction
3-232-071 TC Upper Limit:Display:Bk
3-232-072 TC Upper Limit:Display:C
3-232-073 TC Upper Limit:Display:M
3-232-074 TC Upper Limit:Display:Y
3233 [RTP Vtref Corr :Disp/Set]
3-233-001 ON/OFF
3-233-011 Corr Amt(+):K
3-233-012 Corr Amt(+):C
3-233-013 Corr Amt(+):M
3-233-014 Corr Amt(+):Y
3-233-021 Corr Amt(-):K
3-233-022 Corr Amt(-):C
3-233-023 Corr Amt(-):M
3-233-024 Corr Amt(-):Y
3-233-031 Corr Thresh:K
3-233-032 Corr Thresh:C
3-233-033 Corr Thresh:M
3-233-034 Corr Thresh:Y
*ENG [0 to 5 / 1.0 / 0.1/step]
*ENG [0 to 255 / 100 / 1count/step]
*ENG [0 to 100 / 100 / 1%/step]
*ENG [0 to 255 / 100 / 1count/step]
*ENG [0 to 20 / 3 / 0.1%/step]
*ENG [0 to 5 / 0.5 / 0.1wt%/step]
*ENG [1 to 15 / 9 / 0.1wt%/step]
*ENG [1 to 15 / 9 / 0.1wt%/step]
*ENG [1 to 15 / 9 / 0.1wt%/step]
*ENG [1 to 15 / 9 / 0.1wt%/step]
*ENG [0 to 1 / 1 / 1/step]
*ENG [0 to 1 / 0.03 / 0.01V/step]
*ENG [0 to 1 / 0.03 / 0.01V/step]
*ENG [0 to 1 / 0.03 / 0.01V/step]
*ENG [0 to 1 / 0.03 / 0.01V/step]
*ENG [0 to 1 / 0.03 / 0.01V/step]
*ENG [0 to 1 / 0.03 / 0.01V/step]
*ENG [0 to 1 / 0.03 / 0.01V/step]
*ENG [0 to 1 / 0.03 / 0.01V/step]
*ENG [0 to 0.1 / 0.005 / 0.001mg/cm step]
2
/
*ENG [0 to 0.1 / 0.01 / 0.001mg/cm
2
/step]
*ENG [0 to 0.1 / 0.01/ 0.001mg/cm
2
/step]
*ENG [0 to 0.1 / 0.01 / 0.001mg/cm
2
/step]
3-233-041 Vtavg Weight Coeff (H)
3-233-051 Vtavg Weight Coeff (M)
3-233-061 Vtavg Weight Coeff (L)
3234 [Vtref Corr :Disp/Set]
3-234-001 ON/OFF
3-234-011 Corr Amt(+):K
3-234-012 Corr Amt(+):C
3-234-013 Corr Amt(+):M
3-234-014 Corr Amt(+):Y
3-234-021 Corr Amt(-):K
3-234-022 Corr Amt(-):C
3-234-023 Corr Amt(-):M
3-234-024 Corr Amt(-):Y
3-234-031 P Rank 1 Threshold
3-234-032 P Rank 2 Threshold
3-234-033 P Rank 3 Threshold
3-234-034 P Rank 4 Threshold
3-234-041 T Rank 1 Threshold
3-234-042 T Rank 2 Threshold
3-234-050 Correction Coefficient
3250 [ImgArea :Disp]
3-250-001 ImgArea:K
3-250-002 ImgArea:C
3-250-003 ImgArea:M
3-250-004 ImgArea:Y
*ENG
Engine SP Tables - SP3000
[0 to 100 / 30 / 1%/step]
*ENG [0 to 100 / 0 / 1%/step]
*ENG [0 to 100 / 5 / 1%/step]
*ENG [0 to 1 / 1 / 1/step]
*ENG [0 to 1 / 0.01 / 0.01V/step]
*ENG [0 to 1 / 0.01 / 0.01V/step]
*ENG [0 to 1 / 0.01 / 0.01V/step]
*ENG [0 to 1 / 0.01 / 0.01V/step]
*ENG [0 to 1 / 0.01 / 0.01V/step]
*ENG [0 to 1 / 0.01 / 0.01V/step]
*ENG [0 to 1 / 0.01 / 0.01V/step]
*ENG [0 to 1 / 0.01 / 0.01V/step]
*ENG [0 to 2 / 0.15 / 0.01/step]
*ENG [0 to 2 / 0.05 /0.01/step]
*ENG [-2 to 0 / -0.05 / 0.01/step]
*ENG [-2 to 0 / -0.15 / 0.01/step]
*ENG [-1 to 0 / -0.2 / 0.01V/step]
*ENG [0 to 1 / 0.2 / 0.01V/step]
*ENG [1 to 10 / 10 / 0.1/step]
*ENG [0 to 9999 / 0 / 1cm
*ENG
*ENG
*ENG
2
/step]
331
332
3. Engine SP Mode Tables
3251 [DotCoverage :Disp]
3-251-001 DotCoverage:K
3-251-002 DotCoverage:C
3-251-003 DotCoverage:M
3-251-004 DotCoverage:Y
3-251-011 DC Avg.:S:K
3-251-012 DC Avg.:S:C
3-251-013 DC Avg.:S:M
3-251-014 DC Avg.:S:Y
3-251-021 DC Avg.:M:K
3-251-022 DC Avg.:M:C
3-251-023 DC Avg.:M:M
3-251-024 DC Avg.:M:Y
3-251-031 DC Avg.:L:K
3-251-032 DC Avg.:L:C
3-251-033 DC Avg.:L:M
3-251-034 DC Avg.:L:Y
3-251-041 TotalPage:S:Set
3-251-042 TotalPage:S:Set
3-251-043 TotalPage:S:Set
3-251-051 TotalPage:S:Set
3-251-052 TotalPage:S:Set
3-251-053 TotalPage:S:Set
3-251-151 Total DC: Dev: K
3-251-152 Total DC: Dev: C
3-251-153 Total DC: Dev: M
*ENG [0 to 100 / 0 / 0.01%/step]
*ENG [0 to 100 / 0 / 0.01%/step]
*ENG [0 to 100 / 0 / 0.01%/step]
*ENG [0 to 100 / 0 / 0.01%/step]
*ENG [0 to 100 / 5 / 0.01%/step]
*ENG [0 to 100 / 5 / 0.01%/step]
*ENG [0 to 100 / 5 / 0.01%/step]
*ENG [0 to 100 / 5 / 0.01%/step]
*ENG [0 to 100 / 5 / 0.01%/step]
*ENG [0 to 100 / 5 / 0.01%/step]
*ENG [0 to 100 / 5 / 0.01%/step]
*ENG [0 to 100 / 5 / 0.01%/step]
*ENG [0 to 100 / 5 / 0.01%/step]
*ENG [0 to 100 / 5 / 0.01%/step]
*ENG [0 to 100 / 5 / 0.01%/step]
*ENG [0 to 100 / 5 / 0.01%/step]
*ENG [1 to 255 / 50 / 1count/step]
*ENG [1 to 500 / 50 / 1count/step]
*ENG [1 to 999 / 250 / 1count/step]
*ENG [1 to 255 / 100 / 1count/step]
*ENG [1 to 500 / 50 / 1count/step]
*ENG [1 to 999 / 250 / 1count/step]
*ENG [0 to 100 / 0 / 0.01%/step]
*ENG [0 to 100 / 0 / 0.01%/step]
*ENG [0 to 100 / 0 / 0.01%/step]
Engine SP Tables - SP3000
3-251-154 Total DC: Dev: Y *ENG [0 to 100 / 0 / 0.01%/step]
3252 [AccumImgArea :Disp]
3-252-001 DotCoverage:K
3-252-002 DotCoverage:C
3-252-003 DotCoverage:M
3-252-004 DotCoverage:Y
3-252-011 DC Avg.:S:K
3-252-012 DC Avg.:S:C
3-252-013 DC Avg.:S:M
3-252-014 DC Avg.:S:Y
3300 [RTP Pattern :Disp]
3-300-001 M/A(Latest):K
3-300-002 M/A(Latest):C
3-300-003 M/A(Latest):M
3-300-004 M/A(Latest):Y
3-300-011 M/A(Target):K
3-300-012 M/A(Target):C
3-300-013 M/A(Target):M
3-300-014 M/A(Target):Y
*ENG [0 to 65535 / 0 / 1cm
2
/step]
*ENG [0 to 65535 / 0 / 1cm
2
/step]
*ENG [0 to 65535 / 0 / 1cm
2
/step]
*ENG [0 to 65535 / 0 / 1cm
2
/step]
*ENG [0 to 4294967295 / 0 / 1cm
2
/step]
*ENG [0 to 4294967295 / 0 / 1cm
2
/step]
*ENG [0 to 4294967295 / 0 / 1cm
2
/step]
*ENG [0 to 4294967295 / 0 / 1cm
2
/step]
3260 [Temperature/Humidity: Display]
3-260-001 Temperature ENG
3-260-002 Relative Humidity
3-260-003 Absolute Humidity
ENG
ENG
[-5 to 45 / 0 / 0.1deg/step]
[0 to 100 / 0 / 0.1%RH/step]
[0 to 100 / 0 / 0.01g/m
3
/step]
*ENG [0 to 1 / 0 / 0.001mg/cm
*ENG [0 to 2 / 0 / 0.001mg/cm
*ENG
2
2
*ENG [0 to 2 / 0 / 0.001mg/cm
2
*ENG [0 to 2 / 0 / 0.001mg/cm
2
/step]
/step]
/step]
/step]
*ENG [0 to 1 / 0.225 / 0.001mg/cm
[0 to 1 / 0.4 / 0.001mg/cm
2
*ENG [0 to 1 / 0.4 / 0.001mg/cm
2
2
/step]
/step]
*ENG [0 to 1 / 0.45 / 0.001mg/cm
2
/step]
/step]
333
334
3. Engine SP Mode Tables
3301 [RTP Pattern :Set]
3-301-001 Create Intrvl:BW
3-301-002 Create Intrvl:FC
3-301-011 Page Cnt:BW
3-301-012 Page Cnt:FC
3-301-021 M/A UppErr:K
3-301-022 M/A UppErr:Col
3-301-023 M/A LowErr:K
3-301-024 M/A LowErr:Col
3-301-031 Feed Cnt :Set
3-301-041 Feed Cnt :K
3-301-042 Feed Cnt :C
3-301-043 Feed Cnt :M
3-301-044 Feed Cnt :Y
3-301-081 M/A(RTP)_Std
3-301-091 M/A Thresh_Upp:K
3-301-092 M/A Thresh_Upp:C
3-301-093 M/A Thresh_Upp:M
3-301-094 M/A Thresh_Upp:Y
3-301-101 M/A Thresh_Low:K
3-301-102 M/A Thresh_Low:C
3-301-103 M/A Thresh_Low:M
3-301-104 M/A Thresh_Low:Y
3-301-111 Weight Coeff:K
3-301-112 Weight Coeff:Col
*ENG [0 to 200 / 10 / 1page/step]
*ENG [0 to 200 / 10 / 1page/step]
*ENG [0 to 200 / 0 / 1page/step]
*ENG [0 to 200 / 0 / 1page/step]
*ENG [0 to 1 / 0.6 / 0.001mg/cm
2
/step]
*ENG [0 to 2 / 1.2 / 0.001mg/cm
2
/step]
*ENG [0 to 1 / 0.1 / 0.001mg/cm
2
/step]
*ENG [0 to 1 / 0.2 / 0.001mg/cm
2
/step]
*ENG [0 to 99999999 / 50000 / 1msec/ step]
*ENG [0 to 99999999 / 0 / 1msec/step]
*ENG [0 to 99999999 / 0 / 1msec/step]
*ENG [0 to 99999999 / 0 / 1msec/step]
*ENG [0 to 99999999 / 0 / 1msec/step]
*ENG [0 to 1 / 0.196 / 0.001 mg/cm
2
/step]
*ENG [0 to 1 / 0.086 / 0.001mg/cm
2
/step]
*ENG [0 to 1 / 0.05 / 0.001mg/cm
2
/step]
*ENG [0 to 1 / 0.05 / 0.001mg/cm
2
/step]
*ENG [0 to 1 / 0.05 / 0.001mg/cm
2
/step]
*ENG [0 to 1 / 0.086 / 0.001mg/cm
2
/step]
*ENG [0 to 1 / 0.1 / 0.001mg/cm
2
/step]
*ENG [0 to 1 / 0.1 / 0.001mg/cm
2
/step]
*ENG [0 to 1 / 0.1 / 0.001mg/cm
2
/step]
*ENG [1 to 10 / 1 / 1/step]
*ENG [1 to 10 / 1 / 1/step]
Engine SP Tables - SP3000
3310 [ID.Sens :Voffset]
3-310-001 Voffset reg (Front)
3-310-002 Voffset reg (Center)
3-310-003 Voffset reg (Rear)
3-310-011 Voffset dif (Front)
3-310-012 Voffset dif (Center)
3-310-013 Voffset dif (Rear)
3-310-021 Voffset TM(Front)
3-310-022 Voffset TM(Center)
3-310-023 Voffset TM(Rear)
3311 [ID.Sens :Vmin]
3-311-001 Vmin_K(Front)
3-311-002 Vmin_K(Center)
3-311-003 Vmin_K(Rear)
3312 [ID.Sens :Vct]
3-312-001 Vct_reg(Front)
3-312-002 Vct_reg(Center)
3-312-003 Vct_reg(Rear)
3-312-011 Vct_dif(Front)
3-312-012 Vct_dif(Center)
3-312-013 Vct_dif(Rear)
3320 [Vsg Adj: Execute]
3-320-001 P Sensor
3-320-031 Vsg Error Counter (Front)
*ENG [0 to 5.5 / 0 / 0.01V/step]
*ENG [0 to 5.5 / 0 / 0.01V/step]
*ENG [0 to 5.5 / 0 / 0.01V/step]
*ENG [0 to 5.5 / 0 / 0.01V/step]
*ENG [0 to 5.5 / 0 / 0.01V/step]
*ENG [0 to 5.5 / 0 / 0.01V/step]
*ENG [0 to 5.5 / 0 / 0.01V/step]
*ENG [0 to 5.5 / 0 / 0.01V/step]
*ENG [0 to 5.5 / 0 / 0.01V/step]
*ENG [0 to 5 / 0 / 0.001V/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
ENG
*ENG
[0 to 5 / 0 / 0.001V/step]
[0 or 1 / 0 / 1/step]
[0 to 99 / 0 / 1count/step]
335
336
3. Engine SP Mode Tables
3-320-032 Vsg Error Counter (Center)
3-320-033 Vsg Error Counter (Rear)
3321 [Adjusted Vsg]
3-321-001 Vsg reg (Front)
3-321-002 Vsg reg (Center)
3-321-003 Vsg reg (Rear)
3-321-011 Vsg dif (Front)
3-321-012 Vsg dif (Center)
3-321-013 Vsg dif (Rear)
3-321-041 Vsg TM(Front)
3-321-042 Vsg TM(Center)
3-321-043 Vsg TM(Rear)
3322 [Adjusted Ifsg]
3-322-001 Ifsg RTP (Front)
3-322-002 Ifsg RTP (Center)
3-322-003 Ifsg RTP (Rear)
3-322-011 Ifsg Min (Front)
3-322-012 Ifsg Min (Center)
3-322-013 Ifsg Min (Rear)
3-322-021 Ifsg: TM(Front)
3-322-022 Ifsg: TM(Center)
3-322-023 Ifsg: TM(Rear)
3323 [Vsg Adj OK?]
*ENG
*ENG
[0 to 99 / 0 / 1count/step]
[0 to 99 / 0 / 1count/step]
*ENG [0 to 5.5 / 4 / 0.01V/step]
*ENG [0 to 5.5 / 4 / 0.01V/step]
*ENG [0 to 5.5 / 4 / 0.01V/step]
*ENG [0 to 5.5 / 0 / 0.01V/step]
*ENG [0 to 5.5 / 0 / 0.01V/step]
*ENG [0 to 5.5 / 0 / 0.01V/step]
*ENG [0 to 5.5 / 4 / 0.01V/step]
*ENG [0 to 5.5 / 4 / 0.01V/step]
*ENG [0 to 5.5 / 4 / 0.01V/step]
*ENG [0 to 50 / 10 / 0.001mA/step]
*ENG [0 to 50 / 10 / 0.001mA/step]
*ENG [0 to 50 / 10 / 0.001mA/step]
*ENG [0 to 50 / 27 / 0.001mA/step]
*ENG [0 to 50 / 27 / 0.001mA/step]
*ENG [0 to 50 / 27 / 0.001mA/step]
*ENG [0 to 50 / 10 / 0.001mA/step]
*ENG [0 to 50 / 10 / 0.001mA/step]
*ENG [0 to 50 / 10 / 0.001mA/step]
Engine SP Tables - SP3000
Code
0
1
2
Did not EXEC.
Succeed
Result
ID sensor proofread error detail
-
(SP default)
Out of range from Vsg= Vsg_reg(target value)±x.x[V/step]
9
3-323-001 Latest
4
5
3-323-002 Latest 2
3-323-003 Latest 3
3-323-004 Latest 4
3-323-005 Latest 5
3-323-006 Latest 6
3-323-007 Latest 7
3-323-008 Latest 8
3-323-009 Latest 9
3-323-010 Latest 10
LED Ampere Max. error.
ID sensor output error.
Kill
Ifsg>Max.
Vsg< Vsg_reg(error)
Kill by error of door open, power off.
*ENG [0 to 999 / 0 / 1/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
3330 [ID.Sens Coef :Disp]
3-330-001 K2(Latest) (Front)
3-330-002 K2(Latest) (Center)
3-330-003 K2(Latest) (Rear)
3-330-011 K5(Latest) (Front)
3-330-012 K5(Latest) (Center)
3-330-013 K5(Latest) (Rear)
*ENG [0 to 5 / 0 / 0.0001/step]
*ENG [0 to 5 / 0 / 0.0001/step]
*ENG [0 to 5 / 0 / 0.0001 /step]
*ENG [0 to 10 / 5 / 0.0001/step]
*ENG [0 to 10 / 5 / 0.0001/step]
*ENG [0 to 10 / 5 / 0.0001/step]
337
338
3. Engine SP Mode Tables
3331 [ID.Sens TestVal:F]
3-333-001 K2: Check
3-333-002 Diffuse Corr
3-333-003 Vct_reg Check:Slope
3-333-004 Vct_reg Check:Xint
3-333-005 Vct_dif Check:Slope
3-333-006 Vct_dif Check:Xint
3334 [ID.Sens TestVal:C]
3-334-001 K2: Check
3-334-002 Diffuse Corr
3-334-003 Vct_reg Check:Slope
3-334-004 Vct_reg Check:Xint
3-334-005 Vct_dif Check:Slope
3-334-006 Vct_dif Check:Xint
3335 [ID.Sens TestVal:R]
3-335-001 K2: Check
3-335-002 Diffuse Corr
3-335-003 Vct_reg Check:Slope
3-335-004 Vct_reg Check:Xint
3-335-005 Vct_dif Check:Slope
3-335-006 Vct_dif Check:Xint
3400 [Toner Supply Type]
*ENG [0 to 1 / 0.516 / 0.001/step]
*ENG [0.75 to 1.35 / 1.00 / 0.01/step]
*ENG [0 to 200 / 0.0 / 0.1mV/mA/step]
*ENG [0 to 25.5 / 0.0 / 0.1mA/step]
*ENG [0 to 200 / 0.0 / 0.1mV/mA/step]
*ENG [0 to 25.5 / 0.0 / 0.1mA/step]
*ENG [0 to 1 / 0.516 / 0.001/step]
*ENG [0.75 to 1.35 / 1.00 / 0.01/step]
*ENG [0 to 200 / 0.0 / 0.1mV/mA/step]
*ENG [0 to 25.5 / 0.0 / 0.1mA/step]
*ENG [0 to 200 / 0.0 / 0.1mV/mA/step]
*ENG [0 to 25.5 / 0.0 / 0.1mA/step]
*ENG [0 to 1 / 0.516 / 0.001/step]
*ENG [0.75 to 1.35 / 1.00 / 0.01/step]
*ENG [0 to 200 / 0.0 / 0.1mV/mA/step]
*ENG [0 to 25.5 / 0.0 / 0.1mA/step]
*ENG [0 to 200 / 0.0 / 0.1mV/mA/step]
*ENG [0 to 25.5 / 0.0 / 0.1mA/step]
3-400-001 K
3-400-002 C
3-400-003 M
3-400-004 Y
3411 [Toner Supply Qty]
3-411-001 K
3-411-002 C
3-411-003 M
3-411-004 Y
3420 [DeveloperWeight]
3-420-001 Total_Weight:K
3-420-002 Total_Weight:CMY
3421 [TnrSplyAbility]
3-421-001 K
3-421-002 C
3-421-003 M
3-421-004 Y
3-421-011 TnrSplyAbilityCoef1
3-421-012 TnrSplyAbilityCoef2
3-421-013 TnrSplyAbilityCoef3
3-421-014 TnrSplyAbilityCoef4
3-421-015 TnrSplyAbilityCoef5
Engine SP Tables - SP3000
*ENG [0 to 4 / 4 / 1/step]
*ENG
0: Fixed
2: PID
*ENG
4: DANC
*ENG
ENG [0 to 40000 / 0 / 0.1mg/step]
ENG
ENG
ENG
*ENG [50 to 2000 / 240 / 1g/step]
*ENG
*ENG [0.001 to 2 / 0.71 / 0.001mg/msec/ step]
*ENG [0.001 to 2 / 0.71 / 0.001mg/msec/ step]
*ENG [0.001 to 2 / 0.71 / 0.001mg/msec/ step]
*ENG [0.001 to 2 / 0.71 / 0.001mg/msec/ step]
*ENG [0.5 to 2 / 1.12 / 0.01/step]
*ENG [0.5 to 2 / 1.12 / 0.01/step]
*ENG [0.5 to 2 / 1.10 / 0.01/step]
*ENG [0.5 to 2 / 1.06 / 0.01/step]
*ENG [0.5 to 2 / 1.00 / 0.01/step]
339
340
3. Engine SP Mode Tables
3-421-016 TnrSplyAbilityCoef6
3-421-017 TnrSplyAbilityCoef7
3-421-018 TnrSplyAbilityCoef8
3-421-019 TnrSplyAbilityCoef9
3-421-020 TnrSplyAbilityCoef10
3-421-031 AbsHum Threshold:1
3-421-032 AbsHum Threshold:2
3-421-033 AbsHum Threshold:3
3-421-041 Environ Coef1
3-421-042 Environ Coef2
3-421-043 Environ Coef3
3-421-044 Environ Coef4
3422 [Tnr Supply Limits :Set]
3-422-001 Max Supply Rate:K
3-422-002 Max Supply Rate:C
3-422-003 Max Supply Rate:M
3-422-004 Max Supply Rate:Y
3-422-011 Min Supply Time: K
3-422-012 Min Supply Time: C
3-422-013 Min Supply Time: M
3-422-014 Min Supply Time: Y
3428 [TnrSplyDelay : Setting]
3-428-001 Delay
3440 [Fixed Supply Mode]
*ENG [0.5 to 2 / 0.99 / 0.01/step]
*ENG [0.5 to 2 / 0.98 / 0.01/step]
*ENG [0.5 to 2 / 0.95 / 0.01/step]
*ENG [0.5 to 2 / 0.95 / 0.01/step]
*ENG [0.5 to 2 / 0.95 / 0.01/step]
*ENG [0 to 65 / 6.0 / 0.1g/m
3
/step]
*ENG [0 to 65 / 12.0 / 0.1g/m
3
/step]
*ENG [0 to 65 / 24.0 / 0.1g/m
3
/step]
*ENG [0.5 to 2 / 1.00 / 0.01/step]
*ENG [0.5 to 2 / 1.00 / 0.01/step]
*ENG [0.5 to 2 / 1.00 / 0.01/step]
*ENG [0.5 to 2 / 1.00 / 0.01/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[0 to 255 / 87 / 1%/step]
[0 to 255 / 87 / 1%/step]
[0 to 255 / 87 / 1%/step]
[0 to 255 / 87 / 1%/step]
[0 to 255 / 100 / 1msec/step]
*ENG [0 to 255 / 100 / 1msec/step]
*ENG [0 to 255 / 100 / 1msec/step]
*ENG [0 to 255 / 100 / 1msec/step]
[0 to 255 / 0 / 1msec/step]
3-440-001 Fixed Rate: K
3-440-002 Fixed Rate: C
3-440-003 Fixed Rate: M
3-440-004 Fixed Rate: Y
3460 [TonerSupply :DANC]
3-460-011 Time_Min
3-460-012 Time_Max
3-460-022 SMITH_Weight:K
3-460-023 SMITH_Weight:CMY
3-460-111 Rev_Fix:K
3-460-112 Rev_Fix:C
3-460-113 Rev_Fix:M
3-460-114 Rev_Fix:Y
3461 [TonerSupply :DANC]
3-461-001 PI:Power
3-461-011 PI:P Gain:K
3-461-012 PI:P Limits:Up:K
3-461-013 PI:P Limits:Low:K
3-461-021 PI:I Gain:K
3-461-022 PI:I Limits:Up:K
3-461-023 PI:I Limits:Low:K
3-461-031 PI:P Gain:CMY
3-461-032 PI:P Limits:Up:CMY
3-461-033 PI:P Limits:Low:CMY
3-461-041 PI:I Gain:CMY
Engine SP Tables - SP3000
*ENG [0 to 100 / 10 / 1%/step]
*ENG
*ENG
*ENG
*ENG [0 to 250 / 0 / 1msec/step]
*ENG [0 to 1000 / 200 / 1msec/step]
*ENG [1 to 500 / 71 / 1mg/step]
*ENG [1 to 500 / 140 / 1mg/step]
*ENG [1 to 1.5 / 1 / 0.01/step]
*ENG [1 to 1.5 / 1 / 0.01/step]
*ENG [1 to 1.5 / 1 / 0.01/step]
*ENG [1 to 1.5 / 1 / 0.01/step]
*ENG [5 to 200 / 100 / 1%/step]
*ENG [0 to 1 / 0.001 / 0.0001/step]
*ENG [0 to 1 / 0.1 / 0.01/step]
*ENG [0 to 1 / 0.1 / 0.01/step]
*ENG [0 to 0.1 / 0.005 / 0.0001/step]
*ENG [0 to 1 / 0.2 / 0.01/step]
*ENG [0 to 1 / 0.2 / 0.01/step]
*ENG [0 to 1 / 0.01 / 0.0001/step]
*ENG [0 to 1 / 0.1 / 0.01/step]
*ENG [0 to 1 / 0.1 / 0.01/step]
*ENG [0 to 0.1 / 0.001 / 0.0001/step]
341
342
3. Engine SP Mode Tables
3-461-042 PI:I Limits:Up:CMY
3-461-043 PI:I Limits:Low:CMY
3-461-052 AW:AWIpni:K
3-461-062 AW:AWIpni:CMY
3-461-102 PI:LineSpdCoef:MidSpd:K
3-461-103 PI:LineSpdCoef:LowSpd:K
3-461-112 PI:LineSpdCoef:StdSpd:CMY
3-461-113 PI:LineSpdCoef:LowSpd:CMY
3-461-121 SMITH:Gain:K
3-461-122 SMITH:MidSpd:K
3-461-123 SMITH:LowSpd:K
3-461-131 SMITH:Gain:CMY
3-461-132 SMITH:MidSpd:CMY
3-461-133 SMITH:LowSpd:CMY
3462 [TonerSupply :DANC]
3-462-001 ANC:Power
3-462-101 ANC:Gain:K
3-462-102 ANC:MidSpd:K
3-462-103 ANC:LowSpd:K
3-462-111 ANC:Gain:CMY
3-462-112 ANC:MidSpd:CMY
3-462-113 ANC:LowSpd:CMY
3463 [TonerSupply :DANC]
*ENG [0 to 1 / 0.1 / 0.01/step]
*ENG [0 to 1 / 0.1 / 0.01/step]
*ENG [0 to 2000 / 100 / 1/step]
*ENG [0 to 2000 / 1000 / 1/step]
*ENG [0.05 to 1 / 0.5 / 0.01/step]
*ENG [0.05 to 1 / 0.5 / 0.01/step]
*ENG [0.05 to 1 / 0.5 / 0.01/step]
*ENG [0.05 to 1 / 0.5 / 0.01/step]
*ENG [0 to 2 / 1 / 0.01/step]
*ENG [0 to 1 / 1 / 0.01/step]
*ENG [0 to 1 / 1 / 0.01/step]
*ENG [0 to 2 / 1 / 0.01/step]
*ENG [0 to 1 / 1 / 0.01/step]
*ENG [0 to 1 / 1 / 0.01/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 2 / 1 / 0.01/step]
*ENG [0.05 to 1 / 1 / 0.01/step]
*ENG [0.05 to 1 / 1 / 0.01/step]
*ENG [0 to 2 / 1 / 0.01/step]
*ENG [0.05 to 1 / 1 / 0.01/step]
*ENG [0.05 to 1 / 1 / 0.01/step]
Engine SP Tables - SP3000
3-463-101 Int:I:K
3-463-102 Int:I:C
3-463-103 Int:I:M
3-463-104 Int:I:Y
3-463-111 ANC:ref Sum:K
3-463-112 ANC:ref Sum:C
3-463-113 ANC:ref Sum:M
3-463-114 ANC:ref Sum:Y
3-463-201 ImgArea:K
3-463-202 ImgArea:C
3-463-203 ImgArea:M
3-463-204 ImgArea:Y
3500 [ImgQltyAdj :ON/OFF]
3-500-001 ALL
3-500-002 ProCon
3-500-003 MUSIC Condition:Auto Exe
3-500-004 Init TD Sensor
3-500-006 PresetSealWindup Exe
3509 [ImgQltyAdj :ModeSelect]
3-509-011 ImgQltyAdj Mode Setting
3510 [ImgQltyAdj :ExeFlag]
*ENG [-1000.0000 to 1000.0000 /
0.0000 / 0.0001/step]
*ENG
*ENG
*ENG
*ENG [-1000.0000 to 1000.0000 /
0.0000 / 0.0001/step]
*ENG
*ENG
*ENG
*ENG [0 to 9999 / 0 / 1cm
2
/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[0 or 1 / 1 / 1/step]
[0 or 1 / 1 / 1/step]
[0 or 1 / 1 / 1/step]
[0 or 1 / 1 / 1/step]
[0 or 1 / 0 / 1/step]
[0 to 2 / 0 / 1/step]
343
3. Engine SP Mode Tables
3-510-024 MUSIC
344
3520 [ImgQltyAdj :Interval]
3-520-001 During Job
3-520-002 During Stand-by
3521 [Drum Stop Time :Disp]
3-521-001 Year
3-521-002 Month
3-521-003 Day
3-521-004 Hour
3-521-005 Minute
3-521-011 Year:Col
3-521-012 Month:Col
3-521-013 Day:Col
3-521-014 Hour:Col
3-521-015 Minute:Col
3522 [Drum Stop Environ :Disp]
3-522-001 Temperature
3-522-002 Rel Humidity
3-522-003 Abs Humidity
3-522-011 Temperature:Col
3-522-012 Rel Humidity:Col
*ENG [0 to 3 / 0 / 1/step]
0: OFF
1: Mode:b
2: Mode:a
3: Mode:e
*ENG [0 to 100 / 30 / 1page/step]
*ENG [0 to 100 / 5 / 1minute/step]
*ENG [0 to 99 / 0 / 1year/step]
*ENG [1 to 12 / 1 / 1month/step]
*ENG [1 to 31 / 1 / 1day/step]
*ENG [0 to 23 / 0 / 1hour/step]
*ENG [0 to 59 / 0 / 1minute/step]
*ENG [0 to 99 / 0 / 1year/step]
*ENG [1 to 12 / 1 / 1month/step]
*ENG [1 to 31 / 1 / 1day/step]
*ENG [0 to 23 / 0 / 1hour/step]
*ENG [0 to 59 / 0 / 1minute/step]
*ENG [-1280 to 1270 / 0 / 0.1deg/step]
*ENG [0 to 1000 / 0 / 0.1%RH/step]
*ENG [0 to 1000 / 0 / 0.1g/m
3
/step]
*ENG [-1280 to 1270 / 0 / 0.1deg/step]
*ENG [0 to 1000 / 0 / 0.1%RH/step]
Engine SP Tables - SP3000
3-522-013 Abs Humidity:Col
3529 [ProCon Interval Control :Set]
3-529-001 Gamma Corr
3-529-002 Environ Corr
3-529-003 AbsHum Threshhold
3-529-004 Max Cnt Threshhold
3-529-005 Exe Cnt
3-529-006 Page Cnt:BW
3-529-007 Page Cnt:FC
3530 [PowerON ProCon :Set]
3-530-001 Non-use Time Setting
3-530-002 Temperature Range
3-530-003 Relative Humidity Range
3-530-004 Absolute Humidity Range
3-530-005 Interval:BW
3-530-006 Interval:FC
3-530-007 Page Cnt:BW
3-530-008 Page Cnt:FC
3531 [Non-useTime Procon :Set]
3-531-001 Non-use Time Setting
3-531-002 Temperature Range
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[0 to 1000 / 0 / 0.1g/m
3
[0 to 1440 / 360 / 1minute/step]
[0 to 99 / 10 / 1deg/step]
*ENG [0 to 99 / 50 / 1%RH/step]
*ENG [0 to 99 / 6 / 1g/m
3
/step]
[0 to 5000 / 250 / 1sheet/step]
[0 to 5000 / 100 / 1sheet/step]
[0 to 5000 / 0 / 1sheet/step]
[0 to 5000 / 0 / 1sheet/step]
[0 to 1440 / 360 / 1minute/step]
[0 to 99 / 10 / 1deg/step]
/step]
*ENG [0 or 1 / 1 / 1/step]
0: OFF
1: ON
*ENG [0 or 1 / 1 / 1/step]
0: OFF
1: ON
*ENG [0 to 99 / 4.3 / 0.1g/m
3
/step]
*ENG [0 to 99 / 2 / 1count/step]
ENG [0 to 255 / 0 / 1count/step]
*ENG [0 to 5000 / 0 / 1sheet/step]
*ENG [0 to 5000 / 0 / 1sheet/step]
345
346
3. Engine SP Mode Tables
3-531-003 Relative Humidity Range
3-531-004 Absolute Humidity Range
3-531-005 Maximum Execution Number
3532 [Prediction Control :Set]
3-532-001 Prediction ControlON/OFF
3533 [Interrupt ProCon :Set]
3-533-001 Interval:Set:BW
3-533-002 Interval:Disp:BW
3-533-003 Corr(Short):BW
3-533-004 Corr(Mid):BW
3-533-011 Interval:Set:FC
3-533-012 Interval:Disp:FC
3-533-013 Corr(Short):FC
3-533-014 Corr(Mid):FC
3534 [JobEnd ProCon :Set]
3-534-001 Interval:Set:BW
3-534-002 Interval:Disp:BW
3-534-003 Corr(Short):BW
3-534-004 Corr(Mid):BW
3-534-011 Interval:Set:FC
3-534-012 Interval:Disp:FC
3-534-013 Corr(Short):FC
3-534-014 Corr(Mid):FC
*ENG [0 to 99 / 50 / 1%RH/step]
*ENG [0 to 99 / 6 / 1g/m
3
/step]
*ENG [0 to 99 / 10 / 1count/step]
*ENG
*ENG
*ENG
*ENG
*ENG [0 to 1 / 1 / 0.01/step]
*ENG [0 to 5000 / 200 / 1sheet/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[0 to 1 / 0 / 1/step]
[0 to 5000 / 500 / 1sheet/step]
[0 to 5000 / 500 / 1sheet/step]
[0 to 1 / 1 / 0.01/step]
[0 to 5000 / 200 / 1sheet/step]
[0 to 1 / 1 / 0.01/step]
[0 to 1 / 1 / 0.01/step]
[0 to 5000 / 500 / 1sheet/step]
[0 to 5000 / 500 / 1sheet/step]
[0 to 1 / 1 / 0.01/step]
*ENG [0 to 1 / 1 / 0.01/step]
*ENG [0 to 1000 / 200 / 1sheet/step]
[0 to 5000 / 200 / 1sheet/step]
[0 to 1 / 1 / 0.01/step]
[0 to 1 / 1 / 0.01/step]
Engine SP Tables - SP3000
3539 [Dev Agitating Time :Set]
3-539-001 Time
3-539-010 ON/OFF(by AbsHum)
3-539-011 by AbsHum:1
3-539-012 by AbsHum:2
3-539-013 by AbsHum:3
3-539-014 by AbsHum:4
3-539-015 by AbsHum:5
3-539-016 by AbsHum:6
3-539-021 AbsHum Threshold:1
3-539-022 AbsHum Threshold:2
3-539-023 AbsHum Threshold:3
3-539-024 AbsHum Threshold:4
3-539-025 AbsHum Threshold:5
3-539-030 ON/OFF(by Non-use Time)
3-539-050 ON/OFF(by Non-use Time)
3-539-051 by DotCoverage :1
3-539-052 by DotCoverage :2
3-539-053 by DotCoverage :3
3-539-054 by DotCoverage :4
3-539-055 by DotCoverage :5
3-539-056 by DotCoverage :6
3-539-061 DotCoverage Threshhold:1
3-539-062 DotCoverage Threshhold:2
3-539-063 DotCoverage Threshhold:3
3-539-064 DotCoverage Threshhold:4
*ENG [0 to 3000 / 10 / 1sec/step]
*ENG [0 or 1 / 1 / 1/step]
*ENG [0 to 3000 / 0 / 1sec/step]
*ENG [0 to 3000 / 5 / 1sec/step]
*ENG [0 to 3000 / 5 / 1sec/step]
*ENG [0 to 3000 / 5 / 1sec/step]
*ENG [0 to 3000 / 5 / 1sec/step]
*ENG [0 to 3000 / 5 / 1sec/step]
*ENG [0 to 100 / 4 / 1g/cm
3
/step]
*ENG [0 to 100 / 8 / 1g/cm
3
/step]
*ENG [0 to 100 / 12 / 1g/cm
3
/step]
*ENG [0 to 100 / 16 / 1g/cm
3
/step]
*ENG [0 to 100 / 24 / 1g/cm
3
/step]
*ENG [0 or 1 / 1 / 1/step]
*ENG [0 or 1 / 1 / 1/step]
*ENG [0 to 3000 / 0 / 1sec/step]
*ENG [0 to 3000 / 0 / 1sec/step]
*ENG [0 to 3000 / 5 / 1sec/step]
*ENG [0 to 3000 / 5 / 1sec/step]
*ENG [0 to 3000 / 5 / 1sec/step]
*ENG [0 to 3000 / 5 / 1sec/step]
*ENG [0 to 5000 / 10 / 1%/step]
*ENG [0 to 5000 / 20 / 1%/step]
*ENG [0 to 5000 / 30 / 1%/step]
*ENG [0 to 5000 / 40 / 1%/step]
347
348
3. Engine SP Mode Tables
3-539-065 DotCoverage Threshhold:5
3-539-099 UpperLimit
3541 [Music Interval :Set]
3-541-001 Page Cnt:BW
3-541-002 Page Cnt:FC
3550 [Refresh Mode]
3-550-001 Required Area: K
3-550-002 Required Area: C
3-550-003 Required Area: M
3-550-004 Required Area: Y
3-550-011 Dev. Unit Rotation: Display: Bk
3-550-012 Dev. Unit Rotation: Display: C
3-550-013 Dev. Unit Rotation: Display: M
3-550-014 Dev. Unit Rotation: Display: Y
3-550-031 Reflesh Threshold: Bk
3-550-032 Reflesh Threshold: C
3-550-033 Reflesh Threshold: M
3-550-034 Reflesh Threshold: Y
*ENG [0 to 5000 / 50 / 1%/step]
*ENG [0 to 3600 / 30 / 1sec/step]
*ENG
*ENG
[0 to 5000 / 0 / 1sheet/step]
*ENG [0 to 65535 / 0 / 1cm
2
/step]
*ENG [0 to 65535 / 0 / 1cm
2
/step]
*ENG [0 to 65535 / 0 / 1cm
2
/step]
*ENG [0 to 65535 / 0 / 1cm
2
/step]
*ENG [0 to 1000 / 0 / 0.1m/step]
*ENG [0 to 1000 / 0 / 0.1m/step]
*ENG [0 to 1000 / 0 / 0.1m/step]
*ENG [0 to 1000 / 0 / 0.1m/step]
*ENG [0 to 255 / * / 1cm
2
/step]
*MP C2004: 75
*MP C2504: 84
*ENG [0 to 255 / * / 1cm
2
/step]
*MP C2004: 52
*MP C2504: 56
*ENG [0 to 255 / * / 1cm
2
/step]
*MP C2004: 52
*MP C2504: 56
*ENG [0 to 255 / * / 1cm
2
/step]
*MP C2004: 52
*MP C2504: 56
Engine SP Tables - SP3000
3-550-041 Job End Area Coefficient:K
3-550-042 Job End Vb Coefficient:K
3-550-043 Job End Length:K
3-550-044 Job End Supply
3-550-045 Job End Area Coefficient:YMC
3-550-046 Job End Vb Coefficient:YMC
3-550-047 Job End Length:YMC
3-550-050 Threshold
3-550-081 TC Adj. Consume(Upp Limit)
*ENG [0.1 to 25.5 / * / 0.1/step]
*MP C2004: 44
*MP C2504: 49
*ENG [0 to 100 / 40 / 1%/step]
*ENG [0 to 255 / 10 / 1mm/step]
*ENG [0 to 1 / 0 / 0.001mg/cm
2
/step]
*ENG [0.1 to 25.5 / * / 0.1/step]
*MP C2004: 31
*MP C2504: 33
*ENG [0 to 100 / 40 / 1%/step]
*ENG [0 to 255 / 10 / 1mm/step]
*ENG [0 to 65535 / * / 1cm
2
/step]
*MP C2004: 56
*MP C2504: 62
*ENG [0 to 255 / 0 / 1count/step]
3553 [Transfer belt cleaning]
3-553-001 TransferIdleTime Temperature:H
3-553-004 TransferIdleTime
Temperature:L:ON
*ENG [0 to 3 / 0 / 0.1revolution/step]
3-553-002 TransferIdleTime Temperature:M *ENG [0 to 3 / 0 / 0.1revolution/step]
3-553-003 TransferIdleTime Temperature:L *ENG [0 to 3 / 0 / 0.1revolution/step]
*ENG [0 to 3 / 0 / 0.1revolution/step]
3-553-005 Temperature Threshold:T2
3-553-006 Temperature Threshold:T1
*ENG [20 to 30 / 25 / 1deg/step]
*ENG [0 to 15 / 15 / 1deg/step]
3-553-007 Temperature Threshold:T3
3-553-008 TransferIdleTime Rotation :Initial
3-553-009 TransferIdleTime
Rotation :Middle
*ENG [0 to 30 / 5 / 1deg/step]
*ENG [0 to 3 / 0 / 0.1revolution/step]
*ENG [0 to 3 / 0 / 0.1revolution/step]
349
350
3. Engine SP Mode Tables
3-553-010 TransferIdleTime Rotation :End
3-553-011 Transfer Rotation Threshold:L1
3-553-012
Transfer Rotation Threshold:L2
*ENG [0 to 3 / 0 / 0.1revolution/step]
*ENG [0 to 999999999 / 24000000 /
1mm/step]
*ENG [0 to 999999999 / 96000000 /
1mm/step]
3555 [ImageQuality Adj. Counter:Disp]
3-555-001 Charge AC Control *ENG [0 to 2000 / 0 / 1page/step]
3600 [Select ProCon]
3-600-001 Potential Control
3-600-002 LD Control
3-600-003 TC Adj. Mode
3-600-004 ACC Before ProCon
3-600-010 ActivePotentialControl
3-600-030 IBACC:ON/OFF
3-600-060 Vsg ITB Internal Circumference
Correction
3-600-080 Background Pot
ProCon:ON/OFF setting
3610 [Chrg AC Control]
3-610-001 Std Speed: K
3-610-002 Std Speed: C
3-610-003 Std Speed: M
3-610-004 Std Speed: Y
3611 [Chrg DC Control]
3-611-001 Std Speed: K
*ENG [0 or 1 / 1 / 1/step]
*ENG [0 to 3 / 1 / 1/step]
*ENG [0 to 4 / 4 / 1/step]
*ENG [0 to 3 / 2 / 1/step]
*ENG [0 or 1 / 1 / 1/step]
*ENG [0 or 1 / 1 / 1/step]
*ENG [0 or 1 / 1 / 1/step]
*ENG
*ENG
*ENG
*ENG
*ENG
[0 or 1 / 1 / 1/step]
[0 to 3 / 2.2 / 0.01kV/step]
*ENG [300 to 1000 / 690 / 1-V/step]
3-611-002 Std Speed: C
3-611-003 Std Speed: M
3-611-004 Std Speed: Y
3-611-011 Mid Speed: K
3-611-012 Mid Speed: C
3-611-013 Mid Speed: M
3-611-014 Mid Speed: Y
3-611-021 Low Speed: K
3-611-022 Low Speed: C
3-611-023 Low Speed: M
3-611-024 Low Speed: Y
3-611-201 Now:Std Speed: K
3-611-202 Now:Std Speed: C
3-611-203 Now:Std Speed: M
3-611-204 Now:Std Speed: Y
3-611-211 Now:Mid Speed: K
3-611-212 Now:Mid Speed: C
3-611-213 Now:Mid Speed: M
3-611-214 Now:Mid Speed: Y
3-611-221 Now:Low Speed: K
3-611-222 Now:Low Speed: C
3-611-223 Now:Low Speed: M
3-611-224 Now:Low Speed: Y
3612 [Dev DC Control]
3-612-001 Std Speed: K
Engine SP Tables - SP3000
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [300 to 1000 / 690 / 1-V/step]
*ENG [200 to 800 / 550 / 1-V/step]
351
352
3. Engine SP Mode Tables
3-612-002 Std Speed: C
3-612-003 Std Speed: M
3-612-004 Std Speed: Y
3-612-011 Mid Speed: K
3-612-012 Mid Speed: C
3-612-013 Mid Speed: M
3-612-014 Mid Speed: Y
3-612-021 Low Speed: K
3-612-022 Low Speed: C
3-612-023 Low Speed: M
3-612-024 Low Speed: Y
3-612-120 Set:Vb Limit
3-612-121 Set:Limit TC1
3-612-122 Set:Limit TC2
3-612-123 Set:Page Thresh
3-612-131 Set:Upper Vb Current:K
3-612-132 Set:Upper Vb Current:C
3-612-133 Set:Upper Vb Current:M
3-612-134 Set:Upper Vb Current:Y
3-612-201 Now:Std Speed: K
3-612-202 Now:Std Speed: C
3-612-203 Now:Std Speed: M
3-612-204 Now:Std Speed: Y
3-612-211 Now:Mid Speed: K
3-612-212 Now:Mid Speed: C
3-612-213 Now:Mid Speed: M
*ENG [200 to 800 / 550 / 1-V/step]
*ENG [200 to 800 / 550 / 1-V/step]
*ENG [200 to 800 / 550 / 1-V/step]
*ENG [200 to 800 / 550 / 1-V/step]
*ENG [200 to 800 / 550 / 1-V/step]
*ENG [200 to 800 / 550 / 1-V/step]
*ENG [200 to 800 / 550 / 1-V/step]
*ENG [200 to 800 / 550 / 1-V/step]
*ENG [200 to 800 / 550 / 1-V/step]
*ENG [200 to 800 / 550 / 1-V/step]
*ENG [200 to 800 / 550 / 1-V/step]
*ENG [0 to 500 / 50 / 1V/step]
*ENG [1 to 15 / 6.5 / 0.1wt%/step]
*ENG [1 to 15 / 7 / 0.1wt%/step]
*ENG [0 to 999999 / 35000 / 1page/step]
*ENG [0 to 800 / 600 / 1V/step]
*ENG [0 to 800 / 600 / 1V/step]
*ENG [0 to 800 / 600 / 1V/step]
*ENG [0 to 800 / 600 / 1V/step]
*ENG [200 to 800 / 690 / 1-V/step]
*ENG [200 to 800 / 690 / 1-V/step]
*ENG [200 to 800 / 690 / 1-V/step]
*ENG [200 to 800 / 690 / 1-V/step]
*ENG [200 to 800 / 690 / 1-V/step]
*ENG [200 to 800 / 690 / 1-V/step]
*ENG [200 to 800 / 690 / 1-V/step]
3-612-214 Now:Mid Speed: Y
3-612-221 Now:Low Speed: K
3-612-222 Now:Low Speed: C
3-612-223 Now:Low Speed: M
3-612-224 Now:Low Speed: Y
3613 [LD Power Control]
3-613-001 Std Speed: K
3-613-002 Std Speed: C
3-613-003 Std Speed: M
3-613-004 Std Speed: Y
3-613-011 Mid Speed: K
3-613-012 Mid Speed: C
3-613-013 Mid Speed: M
3-613-014 Mid Speed: Y
3-613-021 Low Speed: K
3-613-022 Low Speed: C
3-613-023 Low Speed: M
3-613-024 Low Speed: Y
3-613-101 PrcsCntrlCorrect:K
3-613-102 PrcsCntrlCorrect:C
3-613-103 PrcsCntrlCorrect:M
3-613-104 PrcsCntrlCorrect:Y
3-613-201 Now:Std Speed: K
3-613-202 Now:Std Speed: C
3-613-203 Now:Std Speed: M
Engine SP Tables - SP3000
*ENG [200 to 800 / 690 / 1-V/step]
*ENG [200 to 800 / 690 / 1-V/step]
*ENG [200 to 800 / 690 / 1-V/step]
*ENG [200 to 800 / 690 / 1-V/step]
*ENG [200 to 800 / 690 / 1-V/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
353
354
3. Engine SP Mode Tables
3-613-204 Now:Std Speed: Y
3-613-211 Now:Mid Speed: K
3-613-212 Now:Mid Speed: C
3-613-213 Now:Mid Speed: M
3-613-214 Now:Mid Speed: Y
3-613-221 Now:Low Speed: K
3-613-222 Now:Low Speed: C
3-613-223 Now:Low Speed: M
3-613-224 Now:Low Speed: Y
3619 [Bias:Spd Corr]
3-619-011 VbCoef:Mid Spd: K
3-619-012 VbCoef:Mid Spd: C
3-619-013 VbCoef:Mid Spd: M
3-619-014 VbCoef:Mid Spd: Y
3-619-021 VbCoef:Low Spd: K
3-619-022 VbCoef:Low Spd: C
3-619-023 VbCoef:Low Spd: M
3-619-024 VbCoef:Low Spd: Y
3-619-051 Offset: Std Spd: K
3-619-052 Offset: Std Spd: C
3-619-053 Offset: Std Spd: M
3-619-054 Offset: Std Spd: Y
3-619-061 Offset: Mid Spd: K
3-619-062 Offset: Mid Spd: C
3-619-063 Offset: Mid Spd: M
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0 to 200 / 100 / 1%/step]
*ENG [0.5 to 1.5 / 1 / 0.01/step]
*ENG [0.5 to 1.5 / 1 / 0.01/step]
*ENG [0.5 to 1.5 / 1 / 0.01/step]
*ENG [0.5 to 1.5 / 1 / 0.01/step]
*ENG [0.5 to 1.5 / 1 / 0.01/step]
*ENG [0.5 to 1.5 / 1 / 0.01/step]
*ENG [0.5 to 1.5 / 1 / 0.01/step]
*ENG [0.5 to 1.5 / 1 / 0.01/step]
*ENG [-128 to 127 / 39 / 1V/step]
*ENG [-128 to 127 / 2 / 1V/step]
*ENG [-128 to 127 / 2 / 1V/step]
*ENG [-128 to 127 / 2 / 1V/step]
*ENG [-128 to 127 / 2 / 1V/step]
*ENG [-128 to 127 / 2 / 1V/step]
*ENG [-128 to 127 / 2 / 1V/step]
3-619-064 Offset: Mid Spd: Y
3-619-071 Offset: Low Spd: K
3-619-072 Offset: Low Spd: C
3-619-073 Offset: Low Spd: M
3-619-074 Offset: Low Spd: Y
3620 [ProCon Target M/A]
3-620-001 Maximum M/A:K
3-620-002 Maximum M/A:C
3-620-003 Maximum M/A:M
3-620-004 Maximum M/A:Y
3622 [Dev Pot :Set]
3-622-001 Current:K
3-622-002 Current:C
3-622-003 Current:M
3-622-004 Current:Y
3-622-011 Current:F_K
3-622-012 Current:F_C
3-622-013 Current:F_M
3-622-014 Current:F_Y
3-622-021 Current:C_K
3-622-022 Current:C_C
3-622-023 Current:C_M
Engine SP Tables - SP3000
*ENG [-128 to 127 / 2 / 1V/step]
*ENG [-128 to 127 / 2 / 1V/step]
*ENG [-128 to 127 / 2 / 1V/step]
*ENG [-128 to 127 / 2 / 1V/step]
*ENG [-128 to 127 / 2 / 1V/step]
*ENG [0.25 to 0.75 / 0.37 /
0.001mg/cm
2
/step]
*ENG [0.25 to 0.75 / 0.4 / 0.001mg/cm
2
/ step]
*ENG [0.25 to 0.75 / 0.45 /
0.001mg/cm
2
/step]
*ENG [0.25 to 0.75 / 0.4 / 0.001mg/cm
2
/ step]
*ENG [0 to 800 / 0 / 1V/step]
*ENG [0 to 800 / 0 / 1V/step]
*ENG [0 to 800 / 0 / 1V/step]
*ENG [0 to 800 / 0 / 1V/step]
*ENG [0 to 800 / 0 / 1V/step]
*ENG [0 to 800 / 0 / 1V/step]
*ENG [0 to 800 / 0 / 1V/step]
*ENG [0 to 800 / 0 / 1V/step]
ENG [0 to 800 / 0 / 1V/step]
ENG [0 to 800 / 0 / 1V/step]
ENG [0 to 800 / 0 / 1V/step]
355
356
3. Engine SP Mode Tables
3-622-024 Current:C_Y
3-622-031 Current:R_K
3-622-032 Current:R_C
3-622-033 Current:R_M
3-622-034 Current:R_Y
3-622-051 UpperLimit
3-622-052 UpperLimit
3-622-053 UpperLimit
3-622-054 UpperLimit
3-622-061 LowerLimit
3-622-062 LowerLimit
3-622-063 LowerLimit
3-622-064 LowerLimit
3-622-101 Target:K
3-622-102 Target:C
3-622-103 Target:M
3-622-104 Target:Y
3-622-111 Target Corr:K
3-622-112 Target Corr:C
3-622-113 Target Corr:M
3-622-114 Target Corr:Y
3-622-121 Vk:Upper_K
3-622-122 Vk:Upper_Col
3-622-123 Vk:Lower_K
3-622-124 Vk:Lower_Col
ENG [0 to 800 / 0 / 1V/step]
ENG [0 to 800 / 0 / 1V/step]
ENG [0 to 800 / 0 / 1V/step]
ENG [0 to 800 / 0 / 1V/step]
ENG [0 to 800 / 0 / 1V/step]
*ENG [400 to 800 / 700 / 1V/step]
*ENG [400 to 800 / 700 / 1V/step]
*ENG [400 to 800 / 700 / 1V/step]
*ENG [400 to 800 / 700 / 1V/step]
*ENG [0 to 400 / 200 / 1V/step]
*ENG [0 to 400 / 200 / 1V/step]
*ENG [0 to 400 / 200 / 1V/step]
*ENG [0 to 400 / 200 / 1V/step]
*ENG [0 to 800 / 0 / 1V/step]
*ENG [0 to 800 / 0 / 1V/step]
*ENG [0 to 800 / 0 / 1V/step]
*ENG [0 to 800 / 0 / 1V/step]
*ENG [-128 to 127 / 0 / 1/step]
*ENG [-128 to 127 / 0 / 1/step]
*ENG [-128 to 127 / 0 / 1/step]
*ENG [-128 to 127 / 0 / 1/step]
*ENG [0 to 255 / 30 / 1-V/step]
*ENG [0 to 255 / 30 / 1-V/step]
*ENG [-128 to 0 / -90 / 1-V/step]
*ENG [-128 to 0 / -60 / 1-V/step]
Engine SP Tables - SP3000
3623 [LD Power :Set]
3-623-001 Std Speed Slope:K
3-623-002 Std Speed Slope:C
3-623-003 Std Speed Slope:M
3-623-004 Std Speed Slope:Y
3-623-011 Std Speed intercept:K
3-623-012 Std Speed intercept:C
3-623-013 Std Speed intercept:M
3-623-014 Std Speed intercept:Y
3-623-021 Mid Speed Slope:K
3-623-022 Mid Speed Slope:C
3-623-023 Mid Speed Slope:M
3-623-024 Mid Speed Slope:Y
3-623-031 Mid Speed intercept:K
3-623-032 Mid Speed intercept:C
3-623-033 Mid Speed intercept:M
3-623-034 Mid Speed intercept:Y
3-623-041 Low Speed Slope:K
3-623-042 Low Speed Slope:C
3-623-043 Low Speed Slope:M
3-623-044 Low Speed Slope:Y
3-623-051 Low Speed intercept:K
3-623-052 Low Speed intercept:C
3-623-053 Low Speed intercept:M
3-623-054 Low Speed intercept:Y
*ENG [-1000 to 1000 / 133 / 1/step]
*ENG [-1000 to 1000 / 133 / 1/step]
*ENG [-1000 to 1000 / 133 / 1/step]
*ENG [-1000 to 1000 / 133 / 1/step]
*ENG [-1000 to 1000 / 31 / 1/step]
*ENG [-1000 to 1000 / 31 / 1/step]
*ENG [-1000 to 1000 / 31 / 1/step]
*ENG [-1000 to 1000 / 31 / 1/step]
ENG [-1000 to 1000 / 133 / 1/step]
ENG [-1000 to 1000 / 133 / 1/step]
ENG [-1000 to 1000 / 133 / 1/step]
ENG [-1000 to 1000 / 133 / 1/step]
ENG [-1000 to 1000 / 31 / 1/step]
ENG [-1000 to 1000 / 31 / 1/step]
ENG [-1000 to 1000 / 31 / 1/step]
ENG [-1000 to 1000 / 31 / 1/step]
*ENG [-1000 to 1000 / 133 / 1/step]
*ENG [-1000 to 1000 / 133 / 1/step]
*ENG [-1000 to 1000 / 133 / 1/step]
*ENG [-1000 to 1000 / 133 / 1/step]
*ENG [-1000 to 1000 / 18 / 1/step]
*ENG [-1000 to 1000 / 18 / 1/step]
*ENG [-1000 to 1000 / 18 / 1/step]
*ENG [-1000 to 1000 / 18 / 1/step]
357
358
3. Engine SP Mode Tables
3624 [TC Adj. Mode]
3-624-001 Target(Upp Limit)
3-624-002 Target(Lwr Limit)
3-624-021 Consumption Pat: DUTY: K
3-624-022 Consumption Pat: DUTY: C
3-624-023 Consumption Pat: DUTY: M
3-624-024 Consumption Pat: DUTY: Y
3-624-031 Max Counts:PowerON
3-624-032 Max Counts:Job In
3-624-033 Max Counts:Printing
3-624-034 Max Counts:Job End
3-624-035 Max Counts:ACC
3-624-036 Max Counts:Initial Setting
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[0 to 1 / 0.10 / 0.01mg/cm
2
/-kV/ step]
[-1 to 0 / -0.12 / 0.01mg/cm
2
/-kV/ step]
[0 to 15 / 15 / 1/step]
[0 to 15 / 15 / 1/step]
[0 to 15 / 15 / 1/step]
[0 to 15 / 15 / 1/step]
[0 to 10 / 1 / 1/step]
[0 to 10 / 0 / 1/step]
*ENG [0 to 10 / 0 / 1/step]
*ENG [0 to 10 / 1 / 1/step]
*ENG [0 to 10 / 2 / 1/step]
*ENG [0 to 10 / 3 / 1/step]
3-624-037 Max Counts:Replenishment
3-624-038 Max Counts:Recovery
3-624-071 AbsHumThresh(Upp)
3-624-072 AbsHumThresh(Low)
3-624-073 AbsHumThresh(Range)
3-624-101 AbsHum: Threshold 2
3-624-102 Delta AbsHum: Threshold 2
*ENG [0 to 10 / 3 / 1/step]
*ENG [0 to 10 / 3 / 1/step]
*ENG [0 to 100 / 18 / 0.01g/m
3
/step]
*ENG [0 to 100 / 4 / 0.01g/m
3
/step]
*ENG [0 to 100 / 12 / 0.01g/m
3
/step]
*ENG [0 to 10000 / 1500 / 0.01g/m
3
/ step]
*ENG [0 to 10000 / 550 / 0.01g/m
3-624-111 Development DC Division Table *ENG [0 to 99 / 11 / 1/step]
3
/step]
3-624-112 Consumption Coefficient
3-624-113 Consumption: Threshold 1
3-624-114 Consumption: Threshold 2
*ENG
*ENG
*ENG
[0 to 10 / 0 / 0.1/step]
[0 to 10000 / 150 / 1mg/step]
[0 to 10000 / 300 / 1 mg/step]
Engine SP Tables - SP3000
3-624-115 Consumption: Threshold 3
3-624-116 Consumption: Threshold 4
3-624-117 Consumption: Threshold 5
3-624-118 Consumption: Threshold 6
3-624-121 Consumption: Threshold (Upp)
*ENG [0 to 10000 / 450 / 1 mg/step]
*ENG [0 to 10000 / 600 / 1 mg/step]
*ENG [0 to 10000 / 750 / 1 mg/step]
*ENG [0 to 10000 / 900 / 1 mg/step]
*ENG [0 to 10000 / 150 / 1 mg/step]
3627 [P Pattern Extraction :Set]
3-627-001 Edge Detection Threshold :K
3-627-002 Edge Detection Threshold :C
3-627-003 Edge Detection Threshold :M
3-627-004 Edge Detection Threshold :Y
3-627-011 Edge Upper Limit:Potential
Control
3-627-012 Edge Upper Limit:IBACC
3-627-013 Edge Upper Limit:RTP
3-627-021 Edge Lower Limit:Potential
Control
3-627-022 Edge Lower Limit:IBACC
3-627-023 Edge Lower Limit:RTP
*ENG
*ENG
*ENG
[0 to 5 / 2 / 0.1V/step]
[0 to 5 / 2.5 / 0.1V/step]
[0 to 5 / 2.5 / 0.1V/step]
*ENG [0 to 5 / 2.5 / 0.1V/step]
*ENG [7 to 10 / 9 / 0.1mm/step]
*ENG
*ENG
*ENG
*ENG
*ENG
[10 to 13 / 12 / 0.1mm/step]
[5 to 8 / 7 / 0.1mm/step]
[4 to 7 / 5 / 0.1mm/step]
[7 to 10 / 8 / 0.1mm/step]
[2 to 5 / 3 / 0.1mm/step]
3628 [ID Pattern Timing :Set]
3-628-001 Scan: YCMK
3-628-002 Detection Delay Time
3-628-003 Delay Time
3-628-004 MUSIC Delay Time
*ENG [-500 to 500 / 0 / 0.1mm/step]
*ENG [0 to 2500 / 0 / 1msec/step]
*ENG [0 to 2500 / 778 / 1msec/step]
*ENG [0 to 2500 / 150 / 1msec/step]
3630 [Dev gamma :Disp/Set]
3-630-001 Current:K *ENG [0.1 to 6 / 0.84 / 0.01mg/cm
2
/-kV/step]
359
360
3. Engine SP Mode Tables
3-630-002 Current:C
3-630-003 Current:M
3-630-004 Current:Y
3-630-011 Target:K
3-630-012 Target:C
3-630-013 Target:M
3-630-014 Target:Y
*ENG [0.1 to 6 / 0.88 / 0.01mg/cm
2
/-kV/step]
*ENG [0.1 to 6 / 0.79 / 0.01mg/cm
2
/-kV/step]
*ENG [0.1 to 6 / 0.92 / 0.01mg/cm
2
/-kV/step]
*ENG [0.5 to 2.55 / 0.84 / 0.01mg/cm
2
/-kV/step]
*ENG [0.5 to 2.55 / 0.88 / 0.01mg/cm
2
/-kV/step]
*ENG [0.5 to 2.55 / 0.79 / 0.01mg/cm
2
/-kV/step]
*ENG [0.5 to 2.55 / 0.92 / 0.01mg/cm
2
/-kV/step]
3-630-061 TnrDensity:K
3-630-062 TnrDensity:C
*ENG [0 to 25.5 / 0 / 0.1wt%/step]
*ENG [0 to 25.5 / 0 / 0.1wt%/step]
3-630-063 TnrDensity:M *ENG [0 to 25.5 / 0 / 0.1wt%/step]
3-630-064 TnrDensity:Y
3-630-111 Current:F_K
3-630-112 Current:F_C
3-630-113 Current:F_M
3-630-114 Current:F_Y
3-630-121 Current:C_K
3-630-122 Current:C_C
*ENG [0 to 25.5 / 0 / 0.1wt%/step]
*ENG [0.1 to 6 / 0.9 / 0.01mg/cm
2
/-kV/step]
*ENG [0.1 to 6 / 0.8 / 0.01mg/cm
2
/-kV/step]
*ENG [0.1 to 6 / 0.8 / 0.01mg/cm
2
/-kV/step]
*ENG [0.1 to 6 / 0.8 / 0.01mg/cm
2
/-kV/step]
*ENG [0.1 to 6 / 0.9 / 0.01mg/cm
2
/-kV/step]
*ENG [0.1 to 6 / 0.8 / 0.01mg/cm
2
/-kV/step]
3-630-123 Current:C_M
3-630-124 Current:C_Y
3-630-131 Current:R_K
3-630-132 Current:R_C
*ENG [0.1 to 6 / 0.8 / 0.01mg/cm
2
/-kV/step]
*ENG [0.1 to 6 / 0.8 / 0.01mg/cm
2
/-kV/step]
*ENG [0.1 to 6 / 0.9 / 0.01mg/cm
2
/-kV/step]
*ENG [0.1 to 6 / 0.8 / 0.01mg/cm
2
/-kV/step]
3-630-133 Current:R_M
3-630-134 Current:R_Y
3-630-141 Range M/A Upp:K
*ENG [0.1 to 6 / 0.8 / 0.01mg/cm
2
/-kV/step]
*ENG [0.1 to 6 / 0.8 / 0.01mg/cm
2
/-kV/step]
*ENG [0.2 to 1 / 0.4 / 0.01mg/cm
2
/step]
3-630-142 Range M/A Low:K *ENG [0 to 0.2 / 0.05 / 0.01mg/cm
2
/step]
3-630-143 Range M/A Upp:Col *ENG [0.2 to 1 / 0.5 / 0.01mg/cm
2
/step]
Engine SP Tables - SP3000
3-630-144 Range M/A Low:Col *ENG [0 to 0.2 / 0.05 / 0.01mg/cm
2
/step]
3631 [Vk :Disp]
3-631-001 Current:K
3-631-002 Current:C
3-631-003 Current:M
3-631-004 Current:Y
3-631-111 Current:F_K
3-631-112 Current:F_C
3-631-113 Current:F_M
3-631-114 Current:F_Y
3-631-121 Current:C_K
3-631-122 Current:C_C
3-631-123 Current:C_M
3-631-124 Current:C_Y
3-631-131 Current:R_K
3-631-132 Current:R_C
3-631-133 Current:R_M
3-631-134 Current:R_Y
3680 [Shading Compensation]
3-680-001 Plus Image Quantity: K
3-680-002 Plus Image Quantity: C
3-680-003 Plus Image Quantity: M
3-680-004 Plus Image Quantity: Y
3-680-011 Minus Image Quantity: K
3-680-012 Minus Image Quantity: C
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[-300 to 300 / 0 / 1-V/step]
[-300 to 300 / 0 / 1-V/step]
[-300 to 300 / 0 / 1-V/step]
*ENG [-300 to 300 / 0 / 1-V/step]
*ENG [-300 to 300 / 0 / 1-V/step]
*ENG [-300 to 300 / 0 / 1-V/step]
*ENG [-300 to 300 / 0 / 1-V/step]
*ENG [-300 to 300 / 0 / 1-V/step]
*ENG [-300 to 300 / 0 / 1-V/step]
*ENG [-300 to 300 / 0 / 1-V/step]
*ENG [-300 to 300 / 0 / 1-V/step]
*ENG [-300 to 300 / 0 / 1-V/step]
*ENG [-300 to 300 / 0 / 1-V/step]
[-300 to 300 / 0 / 1-V/step]
[-300 to 300 / 0 / 1-V/step]
[-300 to 300 / 0 / 1-V/step]
[-20 to 16 / 0 / 1/step]
[-20 to 16 / 0 / 1/step]
[-20 to 16 / 0 / 1/step]
*ENG [-20 to 16 / 0 / 1/step]
*ENG [-20 to 16 / 0 / 1/step]
*ENG [-20 to 16 / 0 / 1/step]
361
362
3. Engine SP Mode Tables
3-680-013 Minus Image Quantity: M
3-680-014 Minus Image Quantity: Y
*ENG [-20 to 16 / 0 / 1/step]
*ENG [-20 to 16 / 0 / 1/step]
3690 [Background Pot ProCon]
3-690-001 Correction Coefficient h:Disp: K
3-690-002 Correction Coefficient h:Disp: C
3-690-003 Correction Coefficient h:Disp: M
3-690-004 Correction Coefficient h:Disp: Y
3-690-011 Correction Coefficient h_1: K
3-690-012 Correction Coefficient h_1: C
3-690-013 Correction Coefficient h_1: M
3-690-014 Correction Coefficient h_1: Y
*ENG [-100 to 100 / 0 / 1-V/step]
*ENG [-100 to 100 / 0 / 1-V/step]
*ENG [-100 to 100 / 0 / 1-V/step]
*ENG [-100 to 100 / 0 / 1-V/step]
*ENG
*ENG
*ENG
*ENG
[-100 to 100 / 0 / 1-V/step]
[-100 to 100 / 0 / 1-V/step]
[-100 to 100 / 0 / 1-V/step]
[-100 to 100 / 0 / 1-V/step]
3-690-021 Correction Coefficient h_1:Upper
3-690-022 Correction Coefficient h_1:Lower
3-690-025 h_1 Coefficient
3-690-031 Dev gamma h_1 :Disp:K
3-690-032 Dev gamma h_1 :Disp:C
3-690-033 Dev gamma h_1 :Disp:M
3-690-034 Dev gamma h_1 :Disp:Y
3-690-051 Vkh_1 :Disp:K
3-690-052 Vkh_1 :Disp:C
3-690-053 Vkh_1 :Disp:M
3-690-054 Vkh_1 :Disp:Y
*ENG
*ENG
[-100 to 100 / 50 / 1-V/step]
[-100 to 100 / 0 / 1-V/step]
*ENG [0 to 255 / 50 / 0.01 / -]
*ENG [0 to 600 / 0 / 0.01mg/cm
2
/-kV/ step]
*ENG [0 to 600 / 0 / 0.01mg/cm
2
/-kV/ step]
*ENG [0 to 600 / 0 / 0.01mg/cm
2
/-kV/ step]
*ENG [0 to 600 / 0 / 0.01mg/cm
2
/-kV/ step]
*ENG
*ENG
*ENG
*ENG
[-300 to 300 / 0 / 1-V/step]
[-300 to 300 / 0 / 1-V/step]
[-300 to 300 / 0 / 1-V/step]
[-300 to 300 / 0 / 1-V/step]
3-690-101 Threshold:Correction Coefficient h *ENG [0 to 255 / 10 / 1-V/step]
Engine SP Tables - SP3000
3-690-102 Threshold:Temperature
3-690-103 Threshold:AbsoluteHumidity:Low
3-690-104 Threshold:AbsoluteHumidity:Hi
3-690-105 Temperature At Prev Correction
3-690-106 Threshold: Temperature change
*ENG [0 to 990 / 100 / 0.1deg/step]
*ENG [0 to 100 / 50 / 0.1g/m
3
/step]
*ENG [100 to 990 / 160 / 0.1g/m
3
/ step]
*ENG [-990 to 990 / 0 / 0.1deg/step]
*ENG [0 to 990 / 100 / 0.1deg/step]
*ENG [0 to 990 / 0 / 0.1g/m3/step] 3-690-107 AbsoluteHumidity At Prev
Correction
3-690-108 Threshold:Humidity change
3-690-109 Count:Disp:Pages
3-690-110 Threshold:Interval
3-690-111 Max: Correction Coefficient change *ENG [0 to 255 / 0 / 1-V/step]
3-690-112 Threshold: Correction Coefficient change
*ENG [0 to 255 / 0 / 1-V/step]
*ENG [0 to 255 / 0 / 1-V/step] 3-690-113 Threshold:Correction Coefficient h:JobEnd
3-690-141 Vk Offset:Low Humidity:K
*ENG [0 to 990 / 50 / 0.1g/m3/step]
*ENG [0 to 999 / 0 / 1 / page]
*ENG [0 to 999 / 0 / 1 / page]
3-690-142 Vk Offset:Low Humidity:CMY
3-690-143 Vk Offset:Std Humidity:K
*ENG [0 to 255 / 100 / 1-V/step]
*ENG [0 to 255 / 100 / 1-V/step]
*ENG [0 to 255 / 100 / 1-V/step]
3-690-144 Vk Offset:Std Humidity:CMY
3-690-145 Vk Offset:Hi Humidity:K
3-690-146 Vk Offset:Hi Humidity:CMY
*ENG
*ENG
*ENG
[0 to 255 / 100 / 1-V/step]
[0 to 255 / 100 / 1-V/step]
[0 to 255 / 100 / 1-V/step]
3700 [New Unit Detection]
3-700-001 ON/OFF Setting
3701 [Manual New Unit Set]
3-701-002 # PCU:K
*ENG [0 or 1 / 1 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
363
3. Engine SP Mode Tables
364
3-701-003 # Dev Unit:K
3-701-025 # PCU:C
3-701-026 # Dev Unit:C
3-701-048 # PCU:M
3-701-049 # Dev Unit:M
3-701-071 # PCU:Y
3-701-072 # Dev Unit:Y
3-701-093 # ITB Unit
3-701-102 # ITB Cleaning Unit
3-701-109 # PTR Unit
3-701-115 # Fusing Unit
3-701-116 Fusing Belt
3-701-118 Pressure Roller
3-701-131 Dust Filter
3-701-142 Waste Toner Bottle
3-701-206 ADF Pick-up Roller
3-701-207 ADF Supply Belt
3-701-208 ADF Reverse Roller
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
3704 [PCU Voltage Correction]
3-704-001 ON/OFF Setting *ENG [0 or 1 / 1 / 1/step]
3800 [Waste Toner Full Detection]
3-800-001 Condition *ENG [0 to 4 / 0 / 1/step]
3-800-002 Page Count 1 After Near Full
3-800-003 Volume Count 1 After Near Full
*ENG [0 to 1000000 / 0 / 1sheet/step]
*ENG [0 to 10000000 / 0 / 0.1mg/step]
3-800-004 Volume Count 1 After Replacement *ENG [0 to 10000000 / 0 / 0.1mg/step]
Engine SP Tables - SP3000
3-800-005 Volume Count 2 After Replacement *ENG [0 to 10000000 / 0 / 0.1mg/step]
3-800-006 Page Count 2 After Near Full
3-800-007 Volume Count 2 After Near Full
*ENG [0 to 1000000 / 0 / 1sheet/step]
*ENG [0 to 10000000 / 0 / 0.1mg/step]
3-800-014 Threshold : Remainder days
3-800-024 Date of detection for near full
*ENG [1 to 255 / 15 / 1day/step]
*ENG [0 or 1 / 0 / 1/step]
3905 [Recycled Parts: New/Old Flag]
3-905-001 OPC:K
3-905-002 OPC:C
3-905-003 OPC:M
3-905-004 OPC:Y
*ENG [0 or 1 / 0 / 1/step]
*ENG
*ENG
*ENG
3990 [Abs Temp.:Get Charge Load]
3-990-001 Temperature: Display
3990 [Abs Humidity:Get Charge Load]
3-990-002 Abs Humidity: Display
*ENG [0 to 70 / 0 / 0.1deg/step]
*ENG [0 to 100 / 0 / 0.01g/m
3
/step]
365
366
3. Engine SP Mode Tables
4008
4-008-001 -
[Sub Scan Magnification Adj]
4010
4-010-001 -
[Sub Scan Registration Adj]
4011
4-011-001 -
[Main Scan Reg]
4012 [Set Scale Mask]
4-012-001 Book:Sub LEdge
4-012-002 Book:Sub TEdge
4-012-003 Book:Main:LEdge
4-012-004 Book:Main:TEdge
4-012-005 ADF: Leading Edge
4-012-007 ADF: Right
4-012-008 ADF: left
4013 [Scanner Free Run]
4-013-001 Book mode :Lamp Off
4-013-002 Book mode :Lamp On
*ENG [-1.0 to 1.0 / 0 / 0.1%/step]
*ENG [-2.0 to 2.0 / 0 / 0.1mm/step]
*ENG [-2.5 to 2.5 / 0 / 0.1mm/step]
ENG [0.0 to 3.0 / 1 / 0.1mm/step]
ENG [0.0 to 3.0 / 0 / 0.1mm/step]
ENG [0.0 to 3.0 / 1 / 0.1mm/step]
ENG [0.0 to 3.0 / 0 / 0.1mm/step]
*ENG [0.0 to 3.0 / 0 / 0.1mm/step]
*ENG [0.0 to 3.0 / 0 / 0.1mm/step]
*ENG [0.0 to 3.0 / 0 / 0.1mm/step]
ENG [0 or 1 / 0 / 1/step]
0: OFF
1: ON
ENG [0 or 1 / 0 / 1/step]
0: OFF
1: ON
Engine SP Tables - SP4000
4020 [Dust Check]
4-020-001 Dust Detect:On/Off
4-020-002 Dust Detect:Lvl
4020 [Dust Check Lvl]
4-020-003 Dust Reject:Lvl
4020 [DF Dust Check]
4-020-011 Dust Detect Level:Rear
4-020-012 Correction Level:Rear
4201 [LoCPP edge level:K]
4-201-001 600dpi 2bit edge1
4-201-002 600dpi 2bit edge2
4-201-003 600dpi 4bit edge1
4-201-004 600dpi 4bit edge2
4-201-005 600dpi 1bit edge1
4-201-006 600dpi 1bit edge2
4-201-011 1200dpi1bit edge12
4-201-012 1200dpi1bit edge34
4-201-013 1200dpi2bit edge12
4-201-014 1200dpi2bit edge34
4202 [LoCPP edge level:C]
ENG [0 or 1 / 0 / 1/step]
0: OFF, 1: ON
ENG [0 to 8 / 4 / 1/step]
0: lowest detection level
8: highest detection level
ENG [0 to 4 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
0: OFF, 1: ON
ENG [0 to 8 / 4 / 1/step]
0:Lowest level
8:Highest level
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
367
3. Engine SP Mode Tables
368
4-202-001 600dpi 2bit edge1
4-202-002 600dpi 2bit edge2
4-202-003 600dpi 4bit edge1
4-202-004 600dpi 4bit edge2
4-202-005 600dpi 1bit edge1
4-202-006 600dpi 1bit edge2
4-202-011 1200dpi 1bit edge12
4-202-012 1200dpi 1bit edge34
4-202-013 1200dpi 2bit edge12
4-202-014 1200dpi 2bit edge34
4203 [LoCPP edge level:M]
4-203-001 600dpi 2bit edge1
4-203-002 600dpi 2bit edge2
4-203-003 600dpi 4bit edge1
4-203-004 600dpi 4bit edge2
4-203-005 600dpi 1bit edge1
4-203-006 600dpi 1bit edge2
4-203-011 1200dpi 1bit edge12
4-203-012 1200dpi 1bit edge34
4-203-013 1200dpi 2bit edge12
4-203-014 1200dpi 2bit edge34
4204 [LoCPP edge level:Y]
4-204-001 600dpi 2bit edge1
4-204-002 600dpi 2bit edge2
4-204-003 600dpi 4bit edge1
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
Engine SP Tables - SP4000
4-204-004 600dpi 4bit edge2
4-204-005 600dpi 1bit edge1
4-204-006 600dpi 1bit edge2
4-204-011 1200dpi 1bit edge12
4-204-012 1200dpi 1bit edge34
4-204-013 1200dpi 2bit edge12
4-204-014 1200dpi 2bit edge34
4301
4-301-001 -
[Operation Check APS Sensor]
*ENG [0 to 255 / 0 / 1/step]
0: Not detected
1: Detected
4303
4-303-001 -
[Min Size for APS]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 to 15 / 15 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
0 : No Original
1: A5-Lengthwise
4305
4-305-001 -
[8K/16K Detection]
*ENG [0 to 3 / 0 / 1/step]
0: Normal Detection
1: A4-Sideways LT-Lengthwise
2: LT-Sideways A4-Lengthwise
3: 8K 16K
4308 [Scan Size Detection]
4-308-001 Detection ON/OFF *ENG [0 to 2 / 1 / 1/step]
0: OFF
1: ON
2: APS
369
370
3. Engine SP Mode Tables
4309 [Scan Size Detect:Setting]
4-309-001 Original Density Thresh
4-309-002 Detection Time
4-309-003 Lamp ON:Delay Time
4-309-004 LED PWM Duty
4310 [Scan Size Detect Value]
4-310-001 S1:R
4-310-002 S1:G
4-310-003 S1:B
4-310-004 S2:R
4-310-005 S2:G
4-310-006 S2:B
4-310-007 S3:R
4-310-008 S3:G
4-310-009 S3:B
4400 [Org Edge Mask]
4-400-001 Book:Sub:LEdge(Left)
4-400-002 Book:Sub:TEdge(Right)
4-400-003 Book:Main:LEdge(Rear)
4-400-004 Book:Main:Tedge(Front)
4-400-005 ADF: Leading Edge
4-400-007 ADF: Right
4-400-008 ADF: left
4417 [IPU Test Pattern]
*ENG [0 to 2 / 1 / 1/step]
*ENG [0 to 255 / 26 / 1digit/step]
*ENG [20 to 100 / 60 / 20msec/step]
*ENG [40 to 200 / 40 / 10msec/step]
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[0 to 255 / 0 / 1digit/step]
[0.0 to 3.0 / 0 / 0.1mm/step]
[0.0 to 3.0 / 0 / 0.1mm/step]
[0.0 to 3.0 / 0 / 0.1mm/step]
[0.0 to 3.0 / 0 / 0.1mm/step]
[0.0 to 3.0 / 0 / 0.1mm/step]
[0.0 to 3.0 / 0 / 0.1mm/step]
[0.0 to 3.0 / 0 / 0.1mm/step]
Engine SP Tables - SP4000
4-417-001 Test Pattern ENG [0 to 8 / 0 / 1/step]
0: Scanned image
1: Gradation main scan A
2: Patch 16C
3: Grid pattern A
4: Slant grid pattern B
5: Slant grid pattern C
6: Slant grid pattern D
7: Scanned+Slant Grid C
8: Scanned+Slant Grid D
4429 [Select Copy Data Security]
4-429-001 Copying
4-429-002 Scanning
4-429-003 Fax Operation
4460 [Digital AE]
4-460-001 Low Limit Value
4-460-002 Background level
4501 [ACC Target Den]
4-501-001 Copy:K:Text
4-501-002 Copy:C:Text
4-501-003 Copy:M:Text
4-501-004 Copy:Y:Text
4-501-005 Copy:K:Photo
4-501-006 Copy:C:Photo
4-501-007 Copy:M:Photo
4-501-008 Copy:Y:Photo
*ENG [0 to 3 / 3 / 1/step]
*ENG [0 to 3 / 3 / 1/step]
*ENG [0 to 3 / 3 / 1/step]
*ENG [0 to 1023 / 364 / 1/step]
*ENG [512 to 1535 / 932 / 1/step]
*ENG [0 to 10 / 5 / 1/step]
*ENG [0 to 10 / 5 / 1/step]
*ENG [0 to 10 / 5 / 1/step]
*ENG [0 to 10 / 5 / 1/step]
*ENG [0 to 10 / 5 / 1/step]
*ENG [0 to 10 / 5 / 1/step]
*ENG [0 to 10 / 5 / 1/step]
*ENG [0 to 10 / 5 / 1/step]
371
372
3. Engine SP Mode Tables
4505 [ACC Cor:Bright]
4-505-001 Master:K
4-505-002 Master:C
4-505-003 Master:M
4-505-004 Master:Y
4-505-005 Slave:K
4-505-006 Slave:C
4-505-007 Slave:M
4-505-008 Slave:Y
4506 [ACC Cor:Dark]
4-506-001 Master:K
4-506-002 Master:C
4-506-003 Master:M
4-506-004 Master:Y
4-506-005 Slave:K
4-506-006 Slave:C
4-506-007 Slave:M
4-506-008 Slave:Y
4520 [IBACC:DetectedValue]
*ENG [-128 to 127 / 0 / 1/step]
*ENG [-128 to 127 / 0 / 1/step]
*ENG [-128 to 127 / 0 / 1/step]
*ENG [-128 to 127 / 0 / 1/step]
*ENG [-128 to 127 / 0 / 1/step]
*ENG [-128 to 127 / 0 / 1/step]
*ENG [-128 to 127 / 0 / 1/step]
*ENG [-128 to 127 / 0 / 1/step]
*ENG [-128 to 127 / 0 / 1/step]
*ENG [-128 to 127 / 0 / 1/step]
*ENG [-128 to 127 / 0 / 1/step]
*ENG [-128 to 127 / 0 / 1/step]
*ENG [-128 to 127 / 0 / 1/step]
*ENG [-128 to 127 / 0 / 1/step]
*ENG [-128 to 127 / 0 / 1/step]
*ENG [-128 to 127 / 0 / 1/step]
4-520-001 Latest:K_P1
4-520-002 Latest:K_P2
4-520-003 Latest:K_P3
4-520-004 Latest:K_P4
4-520-005 Latest:K_P5
4-520-006 Latest:K_P6
4-520-007 Latest:K_P6
4-520-008 Latest:K_P6
4-520-021 Latest:C_P1
4-520-022 Latest:C_P2
4-520-023 Latest:C_P3
4-520-024 Latest:C_P4
4-520-025 Latest:C_P5
4-520-026 Latest:C_P6
4-520-027 Latest:C_P6
4-520-028 Latest:C_P6
Engine SP Tables - SP4000
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG [0 to 1023 / 0 / 1/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
373
374
3. Engine SP Mode Tables
4-520-041 Latest:M_P1
4-520-042 Latest:M_P2
4-520-043 Latest:M_P3
4-520-044 Latest:M_P4
4-520-045 Latest:M_P5
4-520-046 Latest:M_P6
4-520-047 Latest:M_P6
4-520-048 Latest:M_P6
4-520-061 Latest:Y_P1
4-520-062 Latest:Y_P2
4-520-063 Latest:Y_P3
4-520-064 Latest:Y_P4
4-520-065 Latest:Y_P5
4-520-066 Latest:Y_P6
4-520-067 Latest:Y_P6
4-520-068 Latest:Y_P6
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG [0 to 1023 / 0 / 1/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
4-520-102 Previous:K_P2
4-520-103 Previous:K_P3
4-520-104 Previous:K_P4
4-520-105 Previous:K_P5
4-520-106 Previous:K_P6
4-520-107 Previous:K_P6
4-520-108 Previous:K_P6
4-520-121 Previous:C_P1
4-520-122 Previous:C_P2
4-520-123 Previous:C_P3
4-520-124 Previous:C_P4
4-520-125 Previous:C_P5
4-520-126 Previous:C_P6
4-520-127 Previous:C_P6
4-520-128 Previous:C_P6
Engine SP Tables - SP4000
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG [0 to 1023 / 0 / 1/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
375
376
3. Engine SP Mode Tables
4-520-141 Previous:M_P1
4-520-142 Previous:M_P2
4-520-143 Previous:M_P3
4-520-144 Previous:M_P4
4-520-145 Previous:M_P5
4-520-146 Previous:M_P6
4-520-147 Previous:M_P6
4-520-148 Previous:M_P6
4-520-161 Previous:Y_P1
4-520-162 Previous:Y_P2
4-520-163 Previous:Y_P3
4-520-164 Previous:Y_P4
4-520-165 Previous:Y_P5
4-520-166 Previous:Y_P6
4-520-167 Previous:Y_P6
4-520-168 Previous:Y_P6
4540 [Print Coverage]
4-540-001 RY Phase: Option
4-540-002 RY Phase: R
4-540-003 RY Phase: G
4-540-004 RY Phase: B
4-540-005 YR Phase: Option
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG [0 to 1023 / 0 / 1/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
ENG [0 to 255 / 0 / 1/step]
0:OFF
1:ON
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
0:OFF
1:ON
4-540-006 YR Phase: R
4-540-007 YR Phase: G
4-540-008 YR Phase: B
4-540-009 YG Phase: Option
4-540-010 YG Phase: R
4-540-011 YG Phase: G
4-540-012 YG Phase: B
4-540-013 GY Phase: Option
4-540-014 GY Phase: R
4-540-015 GY Phase: G
4-540-016 GY Phase: B
4-540-017 GC Phase: Option
4-540-018 GC Phase: R
4-540-019 GC Phase: G
4-540-020 GC Phase: B
4-540-021 CG Phase: Option
4-540-022 CG Phase: R
4-540-023 CG Phase: G
4-540-024 CG Phase: B
Engine SP Tables - SP4000
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
0:OFF
1:ON
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
0:OFF
1:ON
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
0:OFF
1:ON
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
0:OFF
1:ON
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
377
378
3. Engine SP Mode Tables
4-540-025 CB Phase: Option
4-540-026 CB Phase: R
4-540-027 CB Phase: G
4-540-028 CB Phase: B
4-540-029 BC Phase: Option
4-540-030 BC Phase: R
4-540-031 BC Phase: G
4-540-032 BC Phase: B
4-540-033 BM Phase: Option
4-540-034 BM Phase: R
4-540-035 BM Phase: G
4-540-036 BM Phase: B
4-540-037 MB Phase: Option
4-540-038 MB Phase: R
4-540-039 MB Phase: G
4-540-040 MB Phase: B
4-540-041 MR Phase: Option
4-540-042 MR Phase: R
ENG [0 to 255 / 0 / 1/step]
0:OFF
1:ON
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
0:OFF
1:ON
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
0:OFF
1:ON
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
0:OFF
1:ON
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
0:OFF
1:ON
ENG [-256 to 255 / 0 / 1/step]
Engine SP Tables - SP4000
4-540-043 MR Phase: G
4-540-044 MR Phase: B
4-540-045 RM Phase: Option
4-540-046 RM Phase: R
4-540-047 RM Phase: G
4-540-048 RM Phase: B
4-540-049 WHITE: Option
4-540-050 WHITE:R
4-540-051 WHITE:G
4-540-052 WHITE:B
4-540-053 BLACK: Option
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
0:OFF
1:ON
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
0:OFF
1:ON
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
0:OFF
1:ON
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
ENG [-256 to 255 / 0 / 1/step]
4-540-054 BLACK:R
4-540-055 BLACK:G
4-540-056 BLACK:B
4541 [Photo Correction]
4-541-001 Copied Photo
4550 [Scan Apli:Txt/Print]
4-550-005 MTF: 0(Off) 1-15 (Weak-
Strong)
4-550-006 Smoothing: 0(x1) 1-7 (Weak-
Strong)
ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 15 / 8 / 1/step]
*ENG [0 to 7 / 4 / 1/step]
379
380
3. Engine SP Mode Tables
4-550-007 Brightness: 1-255
4-550-008 Contrast: 1-255
4-550-009 Ind Dot Erase: 0(Off) 1-7
(Weak-Strong)
4551 [Scan Apli:Txt]
4-551-005 MTF: 0(Off) 1-15 (Weak-
Strong)
4-551-006 Smoothing: 0(x1) 1-7 (Weak-
Strong)
4-551-007 Brightness: 1-255
4-551-008 Contrast: 1-255
4-551-009 Ind Dot Erase: 0(Off) 1-7
(Weak-Strong)
4552 [Scan Apli:Txt Dropout]
4-552-005 MTF: 0(Off) 1-15 (Weak-
Strong)
4-552-006 Smoothing: 0(x1) 1-7 (Weak-
Strong)
4-552-007 Brightness: 1-255
4-552-008 Contrast: 1-255
4-552-009 Ind Dot Erase: 0(Off) 1-7
(Weak-Strong)
4553 [Scan Apli:Txt/Photo]
4-553-005 MTF: 0(Off) 1-15 (Weak-
Strong)
4-553-006 Smoothing: 0(x1) 1-7 (Weak-
Strong)
4-553-007 Brightness: 1-255
*ENG [1 to 255 / 128 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [0 to 7 / 0 / 1/step]
*ENG [0 to 15 / 8 / 1/step]
*ENG [0 to 7 / 4 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [0 to 7 / 0 / 1/step]
*ENG [0 to 15 / 8 / 1/step]
*ENG [0 to 7 / 4 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [0 to 7 / 0 / 1/step]
*ENG [0 to 15 / 8 / 1/step]
*ENG [0 to 7 / 4 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
Engine SP Tables - SP4000
4-553-008 Contrast: 1-255
4-553-009 Ind Dot Erase: 0(Off) 1-7
(Weak-Strong)
4554 [Scan Apli:Photo]
4-554-005 MTF: 0(Off) 1-15 (Weak-
Strong)
4-554-006 Smoothing: 0(x1) 1-7 (Weak-
Strong)
4-554-007 Brightness: 1-255
4-554-008 Contrast: 1-255
4-554-009 Ind Dot Erase: 0(Off) 1-7
(Weak-Strong)
4565 [Scan Apli:GrayScale]
4-565-005 MTF: 0(Off) 1-15 (Weak-
Strong)
4-565-006 Smoothing: 0(x1) 1-7 (Weak-
Strong)
4-565-007 Brightness: 1-255
4-565-008 Contrast: 1-255
4-565-009 Ind Dot Erase: 0(Off) 1-7
(Weak-Strong)
4570 [Scan Apli:Col Txt/Photo]
4-570-005 MTF: 0(Off) 1-15 (Weak-
Strong)
4-570-006 Smoothing: 0(x1) 1-7 (Weak-
Strong)
4-570-007 Brightness: 1-255
4-570-008 Contrast: 1-255
*ENG [1 to 255 / 128 / 1/step]
*ENG [0 to 7 / 0 / 1/step]
*ENG [0 to 15 / 8 / 1/step]
*ENG [0 to 7 / 4 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [0 to 7 / 0 / 1/step]
*ENG [0 to 15 / 8 / 1/step]
*ENG [0 to 7 / 4 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [0 to 7 / 0 / 1/step]
*ENG [0 to 15 / 8 / 1/step]
*ENG [0 to 7 / 4 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
381
382
3. Engine SP Mode Tables
4-570-009 Ind Dot Erase: 0(Off) 1-7
(Weak-Strong)
4571 [Scan Apli:Col Gloss Photo]
4-571-005 MTF: 0(Off) 1-15 (Weak-
Strong)
4-571-006 Smoothing: 0(x1) 1-7 (Weak-
Strong)
4-571-007 Brightness: 1-255
4-571-008 Contrast: 1-255
4-571-009 Ind Dot Erase: 0(Off) 1-7
(Weak-Strong)
4572 [Scan Apli:AutoCol]
4-572-005 MTF: 0(Off) 1-15 (Weak-
Strong)
4-572-006 Smoothing: 0(x1) 1-7 (Weak-
Strong)
4-572-007 Brightness: 1-255
4-572-008 Contrast: 1-255
4-572-009 Ind Dot Erase: 0(Off) 1-7
(Weak-Strong)
4580 [Fax Apli:Txt/Chart]
4-580-005 MTF: 0(Off) 1-15 (Weak-
Strong)
4-580-006 Smoothing: 0(x1) 1-7 (Weak-
Strong)
4-580-007 Brightness: 1-255
4-580-008 Contrast: 1-255
*ENG [0 to 7 / 0 / 1/step]
*ENG [0 to 15 / 8 / 1/step]
*ENG [0 to 7 / 4 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [0 to 7 / 0 / 1/step]
*ENG [0 to 15 / 8 / 1/step]
*ENG [0 to 7 / 4 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [0 to 7 / 0 / 1/step]
*ENG [0 to 15 / 8 / 1/step]
*ENG [0 to 7 / 4 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
Engine SP Tables - SP4000
4-580-009 Ind Dot Erase: 0(Off) 1-7
(Weak-Strong)
4-580-010 Texture Erase: 0
4581 [Fax Apli:Txt]
4-581-005 MTF: 0(Off) 1-15 (Weak-
Strong)
4-581-006 Smoothing: 0(x1) 1-7 (Weak-
Strong)
4-581-007 Brightness: 1-255
4-581-008 Contrast: 1-255
4-581-009 Ind Dot Erase: 0(Off) 1-7
(Weak-Strong)
*ENG
*ENG
[0 to 7 / 0 / 1/step]
[0 to 2 / 0 / 1/step]
*ENG [0 to 15 / 8 / 1/step]
*ENG [0 to 7 / 4 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [0 to 7 / 0 / 1/step]
4582 [Fax Apli:Txt/Photo]
4-582-005 MTF: 0(Off) 1-15 (Weak-
Strong)
4-582-006 Smoothing: 0(x1) 1-7 (Weak-
Strong)
4-582-007 Brightness: 1-255
4-582-008 Contrast: 1-255
4-582-009 Ind Dot Erase: 0(Off) 1-7
(Weak-Strong)
4-582-010 Texture Erase: 0
4583 [Fax Apli:Photo]
4-583-005 MTF: 0(Off) 1-15 (Weak-
Strong)
4-583-006 Smoothing: 0(x1) 1-7 (Weak-
Strong)
4-583-007 Brightness: 1-255
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[0 to 15 / 8 / 1/step]
[0 to 7 / 4 / 1/step]
[1 to 255 / 128 / 1/step]
[1 to 255 / 128 / 1/step]
[0 to 7 / 0 / 1/step]
[0 to 2 / 0 / 1/step]
[0 to 15 / 8 / 1/step]
[0 to 7 / 4 / 1/step]
[1 to 255 / 128 / 1/step]
383
384
3. Engine SP Mode Tables
4-583-008 Contrast: 1-255
4-583-009 Ind Dot Erase: 0(Off) 1-7
(Weak-Strong)
4-583-010 Texture Erase: 0
4584 [Fax Apli:Original 1]
4-584-005 MTF: 0(Off) 1-15 (Weak-
Strong)
4-584-006 Smoothing: 0(x1) 1-7 (Weak-
Strong)
4-584-007 Brightness: 1-255
4-584-008 Contrast: 1-255
4-584-009 Ind Dot Erase: 0(Off) 1-7
(Weak-Strong)
4585 [Fax Apli:Original 2]
4-585-005 MTF: 0(Off) 1-15 (Weak-
Strong)
4-585-006 Smoothing: 0(x1) 1-7 (Weak-
Strong)
4-585-007 Brightness: 1-255
4-585-008 Contrast: 1-255
4-585-009 Independent Dot Erase (0)/
1-7 (Strong)
4600 [SBU Version Display]
4-600-001 SBU ID
4609 [Gray Balance Set: R]
4-609-001 Book Scan
*ENG [1 to 255 / 128 / 1/step]
*ENG [0 to 7 / 0 / 1/step]
*ENG [0 to 2 / 0 / 1/step]
*ENG [0 to 15 / 8 / 1/step]
*ENG [0 to 7 / 4 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [0 to 7 / 0 / 1/step]
*ENG [0 to 15 / 8 / 1/step]
*ENG [0 to 7 / 4 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [1 to 255 / 128 / 1/step]
*ENG [0 to 7 / 0 / 1/step]
ENG [0x00 to 0xFF / 0 / 1/step]
*ENG [-384 to 255 / -100 / 1digit/step]
4-609-002 DF Scan
4610 [Gray Balance Set: G]
4-610-001 Book Scan
4-610-002 DF Scan
4611 [Gray Balance Set: B]
4-611-001 Book Scan
4-611-002 DF Scan
4635 [SSCG Correction Set]
4-635-001 Mode Selection
Engine SP Tables - SP4000
*ENG [-384 to 255 / -100 / 1digit/step]
*ENG [-384 to 255 / -100 / 1digit/step]
*ENG [-384 to 255 / -100 / 1digit/step]
*ENG [-384 to 255 / -100 / 1digit/step]
*ENG [-384 to 255 / -100 / 1digit/step]
*ENG [0 to 3 / 1 / 1/step]
0: Do not noise correct SSCG.
1: Only adjust analog (initial value)
2: Only adjust digital
3: Adjust both analog/digital
4646 [Scan Adjust Error]
385
386
3. Engine SP Mode Tables
4-646-001 White level
4-646-002 Black level
ENG [0 to 65535 / 0 / 1/step]
Bit15:Unused
Bit14: Unused
Bit13:White level abnormal (F side/RED/EVEN pixel)
Bit12: White level abnormal (F side /RED/ODD pixel)
Bit11: White level abnormal (F side /GREEN/EVEN pixel)
Bit10: White level abnormal (F side /GREEN/ODD pixel)
Bit9: White level abnormal (F side /BLUE/EVEN pixel)
Bit8:White level abnormal (F side /BLUE/ODD pixel)
Bit7: Unused
Bit6: Unused
Bit5:gain abnormal (F side /RED/EVEN pixel)
Bit4: gain abnormal (F side /RED/ODD pixel)
Bit3: gain abnormal (F side /GREEN/EVEN pixel)
Bit2: gain abnormal (F side /GREEN/ODD pixel)
Bit1: gain abnormal (F side /BLUE/EVEN pixel)
Bit0: gain abnormal (F side /BLUE/ODD pixel)
ENG [0 to 65535 / 0 / 1/step]
Bit7: Unused
Bit6: Unused
Bit5: Black level abnormal (F side/RED/EVEN Pixel)
Bit4: Black level abnormal (F side /RED/ODD Pixel)
Bit3: Black level abnormal (F side /GREEN/EVEN Pixel)
Bit2: Black level abnormal (F side /GREEN/ODD Pixel)
Bit1: Black level abnormal (F side /BLUE/EVEN Pixel)
Bit0: Black level abnormal (F side /BLUE/ODD Pixel)
Engine SP Tables - SP4000
4-646-003 SSCG Correction ENG [0 to 65535 / 0 / 1/step]
Bit7: Unused
Bit6: Unused
Bit5: SSCG correction error (Fside/RED/EVEN Pixel)
Bit4: SSCG correction error (Fside/RED/ODD Pixel)
Bit3: SSCG correction error (Fside/GREEN/EVEN Pixel)
Bit2: SSCG correction error (Fside/GREEN/ODD Pixel)
Bit1: SSCG correction error (Fside/BLUE/EVEN Pixel)
Bit0: SSCG correction error (Fside/BLUE/ODD Pixel)
4647 [Scanner Hard Error]
4-647-001 Power-ON ENG [0 to 65535 / 0 / 1/step]
Bit15: Unused
Bit14:SBU hardware error (Power ON/un-reset error)
Bit13:SBU hardware error (Serial communication error: F side)
Bit12:SBU hardware error (Reset error: F side)
Bit11: Unused
Bit10: Unused
Bit9:SBU hardware error (Version error)
Bit8: Unused
Bit7: Unused
Bit6: Unused
Bit5:SBU hardware error (Serial communication error: L side)
Bit4:SBU hardware error (Reset error:Lside)
Bit3: Unused
Bit2: Unused
Bit1: Unused
4688 [DF Density Adjustment]
4-688-001 ARDF *ENG [80 to 120 / 106 / 1%/step]
387
388
3. Engine SP Mode Tables
4688 [Scan Image Density Adjustment]
4-688-002 1-pass DF *ENG [[80 to 120 / 101 / 1%/step]
4699
4-699-001 -
[SBU Test Pattern Change]
ENG [0 to 255 / 0 / 1/step]
4700
4-700-001 -
[CIS ID Display]
4712
4-712-001 -
[CIS GB Adj. Value: R]
4713
4-713-001 -
[CIS GB Adj. Value: G]
4714
4-714-001 -
[CIS GB Adj. Value: B]
4730 [FROM ADF Factory Setting]
4-730-001 CIS Parameter
4730 [FROM Main Factory Setting]
4-730-002 Execution ON/OFF
4-730-003 Execution Flag
4730
4-730-004 -
[FROM Data Update]
4745
4-745-001 -
[CIS Image Level Error Flag]
ENG
*ENG
*ENG
*ENG
ENG
ENG
*ENG
ENG
ENG
[0x00 to 0xFF / 0 / 1/step]
[0 to 2048 / 1023 / 1digit/step]
[0 to 2048 / 1023 / 1digit/step]
[0 to 2048 / 1023 / 1digit/step]
[0 or 1 / 0 / 0/step]
[0 or 1 / 0 / 0/step]
[0 or 1 / 0 / 1/step]
[0 to 1 / 0 / 0/step]
[0 to 65535 / 0 / 1/step]
Engine SP Tables - SP4000
4746
4-746-001 -
[CIS GB Adj Error Flag]
4747
4-747-001 -
[CIS Hard Error Flag]
ENG [0 to 7 / 0 / 1/step]
ENG [0 to 15 / 0 / 1/step]
4796 [Low Density Color Correction]
4-796-001 Front Side
4-796-002 Rear Side
*ENG [0 to 3 / 0 / 1/step]
0: OFF
1: WEAK
2: MEDIUM
3: STRONG
*ENG [0 to 3 / 0 / 1/step]
0: OFF
1: WEAK
2: MEDIUM
3: STRONG
4797 [Rear Side: Digital AE]
4-797-001 Low Limit Setting
4-797-002 Background Erase Level
4799 [CIS TEST Pattern]
4-799-001 select
*ENG
*ENG
[0 to 1023 / 364 / 1/step]
[512 to 1535 / 932 / 1/step]
ENG [0 to 5 / 0 / 1/step]
Sets CIS test pattern output.
0: Scanned Image
1: Fixed Value Pattern
2: EO Fixed Value Pattern
3: Main Scan Gradation
4: Sub Scan Gradation
5: Grid Pattern
389
390
3. Engine SP Mode Tables
4-799-002 Even Output Level Setting
4-799-003 Odd Output Level Setting
4803
4-803-001 -
[Home Position Adj Value]
4853 [Partial LED ON]
4-853-001 ON/OFF(Scan)
4-853-002 ON/OFF(Size Detection)
4871 [Distortion Corr.]
4-871-001 Distortion Corr. ON/OFF
4-871-002 Distortion Initialization
4-871-003 Magnification Adjust(DF)
4-871-004 Magnification Adjust(FB)
4902 [Disp ACC Data]
4-902-001 R_DATA1
4-902-002 G_DATA1
4-902-003 B_DATA1
4-902-004 R_DATA2
4-902-005 G_DATA2
4-902-006 B_DATA2
4903 [Filter Setting]
4-903-001 Ind Dot Erase: Text
4-903-002 Ind Dot Erase: Generation
Copy
ENG
ENG
ENG
[0 to 1023 / 0 / 1digit/step]
[0 to 1023 / 0 / 1digit/step]
[-2.0 to 2.0 / 0 / 0.1mm/step]
*ENG [0 or 1 / 1 / 1/step]
*ENG [0 or 1 / 1 / 1/step]
*ENG [0 or 1 / 1 / 1/step]
*ENG [0 to 3 / 0 / 1/step]
*ENG [-0.35 to 0.35 / 0.11 / 0.01%/step]
*ENG [-0.35 to 0.35 / 0 / 0.01%/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 7 / 0 / 1/step]
*ENG
[0 to 7 / 0 / 1/step]
Engine SP Tables - SP4000
4905
4-905-001 -
[Select Gradation Level]
4918
4-918-009 -
[Man Gamma Adj]
4930 [Coverage Ctrl: Text]
4-930-001 Copy: Full Color 1
4-930-002 Copy: Full Color 2
4-930-003 Copy: Single Color
4-930-004 Copy: Color Conversion
4-930-005 Coverage Ctrl OFF
4931 [Coverage Ctrl: Photo]
4-931-001 Copy: Full Color 1
4-931-002 Copy: Full Color 2
4-931-003 Copy: Single Color
4-931-004 Copy: Color Conversion
4-931-005 Coverage Ctrl OFF
4938 [ACS:Edge Mask]
4-938-001 Copy:Sub LEdge
4-938-002 Copy:Sub TEdge
4-938-003 Copy:Main LEdge
4-938-004 Copy:Main TEdge
4-938-005 Scan:Sub LEdge
4-938-006 Scan:Sub TEdge
*ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 255 / 0 / 1/step]
[- / - / -]
[0 to 400 / 200 / 1/step]
[0 to 400 / 200 / 1/step]
[0 to 400 / 100 / 1/step]
[0 to 400 / 180 / 1/step]
[0 to 400 / 400 / 1/step]
ENG [0 to 400 / 240 / 1/step]
ENG [0 to 400 / 260 / 1/step]
ENG [0 to 400 / 100 / 1/step]
ENG [0 to 400 / 200 / 1/step]
ENG [0 to 400 / 400 / 1/step]
*ENG [0 to 31 / 10 / 1mm/step]
*ENG [0 to 31 / 10 / 1mm/step]
*ENG [0 to 31 / 10 / 1mm/step]
*ENG [0 to 31 / 10 / 1mm/step]
*ENG [0 to 31 / 15 / 1mm/step]
*ENG [0 to 31 / 15 / 1mm/step]
391
3. Engine SP Mode Tables
4-938-007 Scan:Main LEdge
4-938-008 Scan:Main TEdge
4939
4-939-001 -
[ACS:Color Range]
*ENG
*ENG
[0 to 31 / 15 / 1mm/step]
[0 to 31 / 15 / 1mm/step]
*ENG [-2 to 2 / 0 / 1/step]
Change the value of this SP to negative
(“-1” or “-2”) when a black and white document is misjudged as a color document.
4954 [Restore Test Chart]
4-954-005 Chromaticity Rank
4958 [Restore Test Chart: Rear]
4-958-005 Chromaticity Rank
4984 [IBACC Target Den]
4-984-001 IBACC notch K
4-984-002 IBACC notch C
4-984-003 IBACC notch M
4-984-004 IBACC notch Y
4993 [High Light Correction]
4-993-001 Sensitivity Selection
ENG
ENG
[0 to 255 / 0 / 1/step]
[0 to 255 / 0 / 1/step]
*ENG [0 to 10 / 5 / 1/step]
*ENG
*ENG
*ENG
4-993-002 Range Selection
ENG [0 to 9 / 4 / 1/step]
0: Weak
9: Strong
ENG [0 to 9 / 4 / 1/step]
0: Weak
9: Strong
392
4994 [Adj Txt/Photo Recog Level]
Engine SP Tables - SP4000
4-994-001 High Compression PDF
4996
4-996-001 -
[White Paper Detection Level]
ENG [0 to 2 / 1 / 1/step]
ENG [0 to 6 / 3 / 1/step]
393
394
3. Engine SP Mode Tables
5126
5-126-001 -
[Set F-size Document]
5131
5-131-001 -
[Paper Size Type Selection]
*ENG [0 to 2 / * / 1/step]
*NA: 1, EU: 2, Asia: 2, CHN: 2, TWN: 2 ,
KOR: 2
---
0: JP (Japan)
1: NA
2: EU
5135
5-135-001 -
[LG_Oficio Change]
*ENG [0 or 1 / 0 / 1/step]
5181 [Size Adjust]
5-181-001 TRAY 1
ENG [0 to 2 / 0 / 1/step]
0: 8 1/2 x13
1: 8 1/4 x13
2: 8 x13
*ENG [0 to 3 / * / 1/step]
*NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
KOR: 0
0: A4 LEF
1: LT LEF
2: B5 LEF
3: A5 LEF
5-181-002 TRAY 2: 1
5-181-003 TRAY 2: 2
5-181-004 TRAY 2: 3
5-181-005 TRAY 2: 4
5-181-006 TRAY 2: 5
5-181-007 TRAY 3/T-LCT: 1
Engine SP Tables - SP5000
*ENG [0 or 1 / * / 1/step]
*NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
KOR: 0
0: A4 LEF
1: LT LEF
*ENG [0 or 1 / * / 1/step]
*NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
KOR: 0
0: A3
1: DLT
*ENG [0 or 1 / * / 1/step]
*NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
KOR: 0
0: B4
1: LG
*ENG [0 or 1 / * / 1/step]
*NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
KOR: 0
0: B5LEF
1: ExeLEF
*ENG [0 or 1 / * / 1/step]
*NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
KOR: 0
0: SRA3
1: 12X18
*ENG [0 or 1 / * / 1/step]
*NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
KOR: 0
0: A4LEF
1: LTLEF
395
396
3. Engine SP Mode Tables
5-181-008 TRAY 3: 2
5-181-009 TRAY 3: 3
5-181-010 TRAY 3: 4
5-181-011 TRAY 3: 5
5-181-012 TRAY 4: 1
5-181-013 TRAY 4: 2
*ENG [0 or 1 / * / 1/step]
*NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
KOR: 0
0: A3
1: DLT
*ENG [0 or 1 / * / 1/step]
*NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
KOR: 0
0: B4
1: LG
*ENG [0 or 1 / * / 1/step]
*NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
KOR: 0
0: B5LEF
1: ExeLEF
*ENG [0 or 1 / * / 1/step]
*NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
KOR: 0
0: 12.6X17.7
1: 12X18
*ENG [0 or 1 / * / 1/step]
*NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
KOR: 0
0: A4LEF
1: LTLEF
*ENG [0 or 1 / * / 1/step]
*NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
KOR: 0
0: A3
1: DLT
Engine SP Tables - SP5000
5-181-014 TRAY 4: 3
5-181-015 TRAY 4: 4
5-181-016 TRAY 4: 5
5-181-017 LCT
*ENG [0 or 1 / * / 1/step]
NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 , KOR:
0
0: B4
1: LG
*ENG [0 or 1 / * / 1/step]
*NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
KOR: 0
0: B5LEF
1: ExeLEF
*ENG [0 or 1 / * / 1/step]
*NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
KOR: 0
0: 12.6X17.7
1: 12X18
*ENG [0 to 2 / * / 1/step]
*NA: 1, EU: 0, Asia: 0, CHN: 0, TWN: 0 ,
KOR: 0
0: A4LEF
1: LTLEF
2: B5LEF
5186
5-186-001 -
[RK4]
*ENG [0 or 1 / 0 / 1/step]
5610 [Base Gamma Ctrl Pt:Execute]
5-610-004 Get Factory Default
5-610-005 Set Factory Default
5-610-006 Restore Orginal Value
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
5611 [Toner Color in 2C]
397
398
3. Engine SP Mode Tables
5-611-001 B-C
5-611-002 B-M
5-611-003 G-C
5-611-004 G-Y
5-611-005 R-M
5-611-006 R-Y
5801 [Memory Clear]
5-801-002 Engine
5803
5804
*ENG [0 to 128 / 100 / 1/step]
*ENG [0 to 128 / 100 / 1/step]
*ENG [0 to 128 / 100 / 1/step]
*ENG [0 to 128 / 100 / 1/step]
*ENG [0 to 128 / 100 / 1/step]
*ENG [0 to 128 / 100 / 1/step]
[INPUT Check]
See page 448 "Input Check Table"
ENG [- / - / -]
[Execute]
[OUTPUT Check]
See page 475 "Output Check Table"
5805 [Anti-Condensation Heater]
5-805-001 0:OFF / 1:ON *ENG [0 or 1 / 0 / 1/step]
0: OFF... Switches OFF when standby
(default setting)
1: ON... Switches ON when standby
5810 [SC Reset]
5-810-001 Fusing SC Reset
5-810-002 Hard High Temp. Detection
5811 [MachineSerial]
5-811-002 Display
ENG
ENG
*ENG
Clears the fusing SC.
Clears the fusing hardware SC.
[0 to 255 / 0 / 1/step]
Engine SP Tables - SP5000
5811 [MachineSerial Set]
5-811-004 BCU
5811 [Machine Serial: Update Date]
5-811-021 Latest
5-811-022 Previous
5811 [MachineSerial]
5-811-023 Previous
5811 [Machine Serial: Update Date]
5-811-024 Latest (BCU)
5-811-025 Previous (BCU)
5811 [MachineSerial]
5-811-026 Previous (BCU)
*ENG [0 to 255 / 0 / 1/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 to 255 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 to 255 / 0 / 1/step]
5894 [External Mech Count Setting]
5-894-001 Mech Counter Switch Setting
5900 [Engine Log Upload]
5-900-001 Pattern
5-900-002 Trigger
*ENG [0 to 2 / 0 / 1/step]
*ENG [0 to 4 / 0 / 1/step]
*ENG [0 to 3 / 0 / 1/step]
5998 [Fusing Warm UP]
5-998-001 Warm Up In Advance ON/OFF *ENG [0 or 1 / 0 / 1/step]
399
400
3. Engine SP Mode Tables
6006 [ADF Adjustment]
6-006-001 Side-to-Side Regist: Front
6-006-002 Side-to-Side Regist: Rear
6-006-003 Leading Edge Registration:
Front
6-006-004 Leading Edge Registration:
Rear
6-006-005 Buckle: Duplex Front
6-006-006 Buckle: Duplex Rear
6-006-007 Rear Edge Erase Front
6-006-008 Rear Edge Erase Rear
6-006-010 L-Edge Regist (1-Pass): Front
6-006-011 L-Edge Regist (1-Pass): Rear
6-006-012 1st Buckle (1-Pass)
6-006-013 2nd Buckle (1-Pass)
6-006-014 T-Edge Erase (1-Pass): Front
6-006-015 T-Edge Erase (1-Pass): Rear
6007
6008
*ENG [-3.0 to 3.0 / 0 / 0.1mm/step]
*ENG [-3.0 to 3.0 / 0 / 0.1mm/step]
*ENG [-5.0 to 5.0 / 0 / 0.1mm/step]
*ENG [-5.0 to 5.0 / 0 / 0.1mm/step]
[ADF INPUT Check]
See page 448 "Input Check Table"
[ADF OUTPUT Check]
See page 475 "Output Check Table"
*ENG [-5.0 to 5.0 / 0 / 0.1mm/step]
*ENG [-5.0 to 5.0 / 0 / 0.1mm/step]
*ENG [-10.0 to 10.0 / -2.3 / 0.1mm/step]
*ENG [-10.0 to 10.0 / -2.3 / 0.1mm/step]
*ENG [-5.0 to 5.0 / 0 / 0.1mm/step]
*ENG [-5.0 to 5.0 / 0 / 0.1mm/step]
*ENG [-3.0 to 3.0 / 0 / 0.1mm/step]
*ENG [-2.0 to 3.0 / 0 / 0.1mm/step]
*ENG [-5.0 to 5.0 / -3.0 / 0.1mm/step]
*ENG [-5.0 to 5.0 / -2.5 / 0.1mm/step]
Engine SP Tables - SP6000
6009 [ADF FreeRun]
6-009-001 Free Run Simplex Motion
6-009-002 Free Run Duplex Motion
6-009-003 Free Run Stamp Motion
6-009-004 Free Run Simplex Motion(low speed)
6-009-005 Free Run Simplex Motion(high speed)
6-009-006 Free Run Duplex Motion(low speed)
6-009-007 Free Run Duplex Motion(high speed)
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
6010
6-010-001 -
[Stamp Position Adj.]
6011 [1-Pass ADF INPUT Check]
See page 448 "Input Check Table"
*ENG [-5.0 to 5.0 / 0 / 0.1mm/step]
6012 [1-Pass ADF OUTPUT Check]
See page 475 "Output Check Table"
6016
6-016-001 -
[Original Size Detect Setting]
*ENG [0 to 255 / 0 / 1/step]
6017
6-017-001 -
[DF Magnification Adj.]
*ENG [-5 to 5 / 0 / 0.1%/step]
6020
6-020-001 -
[Skew Correction Moving Setting]
*ENG [0 or 1 / 0 / 1/step]
401
402
3. Engine SP Mode Tables
6121 [NV Adj. Data Mod.]
6-121-001 Jogger Pos. Factory Adj.
6-121-002 Folding Pos. Factory Adj.
6125 [Use Paper Guide(Big Size)]
6-125-001 All Size
ENG
ENG
[-3 to 3 / 0 / 0.5mm/step]
[-1.4 to 1.4 / 0 / 0.2mm/step]
ENG [0 or 1 / 0 / 1/step]
6126 [Use Paper Guide(Small Size)]
6-126-001 All Size ENG [0 or 1 / 0 / 1/step]
6130 [Sub-scan PunchPosAdj:FrontFIN]
6-130-001 Domestic 2Hole(Europe 2Hole) ENG [-7.5 to 7.5 / 0 / 0.5mm/step]
6-130-002 North America 3Hole
6-130-003 Europe 4Hole
ENG
ENG
6-130-004 North Europe 4Hole
6-130-005 North America 2Hole
ENG
ENG
6131 [Main-scan PunchPosAdj:FrontFIN]
6-131-001 Domestic 2Hole(Europe 2Hole) ENG [-2 to 2 / 0 / 0.4mm/step]
6-131-002 North America 3Hole
6-131-003 Europe 4Hole
ENG
ENG
6-131-004 North Europe 4Hole
6-131-005 North America 2Hole
ENG
ENG
6132 [Jogger Fence Fine Adj:FrontFIN]
6-132-001 A3T
6-132-002 B4T
6-132-003 A4T
ENG [-1.5 to 1.5 / 0 / 0.5mm/step]
ENG [-3 to 3 / 0 / 0.5mm/step]
ENG [-3 to 3 / 0 / 0.5mm/step]
Engine SP Tables - SP6000
6-132-004 A4Y
6-132-005 B5T
6-132-006 B5Y
6-132-007 DLT-T
6-132-008 LG-T
6-132-009 Oficio-T
6-132-010 LT-T
6-132-011 LT-Y
6-132-012 8K-T
6-132-013 16K-T
6-132-014 16K-Y
6-132-015 Other
6133 [Staple Position Adj: FrontFIN]
6-133-001 Finisher1 ENG [-2 to 2 / 0 / 0.5mm/step]
6134 [Finisher Free Run: FrontFIN]
6-134-001 Free Run1
6-134-002 Free Run2
6-134-003 Free Run3
6-134-004 Free Run4
6135 [INPUT Check: FrontFIN]
See page 448 "Input Check Table"
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
6136 [OUTPUT Check: FrontFIN]
See page 475 "Output Check Table"
ENG [-1.5 to 1.5 / 0 / 0.5mm/step]
ENG [-3 to 3 / 0 / 0.5mm/step]
ENG [-3 to 3 / 0 / 0.5mm/step]
ENG [-3 to 3 / 0 / 0.5mm/step]
ENG [-3 to 3 / 0 / 0.5mm/step]
ENG [-3 to 3 / 0 / 0.5mm/step]
ENG [-3 to 3 / 0 / 0.5mm/step]
ENG [-3 to 3 / 0 / 0.5mm/step]
ENG [-3 to 3 / 0 / 0.5mm/step]
ENG [-3 to 3 / 0 / 0.5mm/step]
ENG [-3 to 3 / 0 / 0.5mm/step]
ENG [-3 to 3 / 0 / 0.5mm/step]
403
404
3. Engine SP Mode Tables
6140
6-140-001 -
6-140-002 -
[Staple Position Adj: 1K FIN]
ENG [-3.5 to 3.5 / 0 / 0.5mm/step]
ENG [-3 to 3 / 0 / 0.3mm/step]
6141 [Booklet Stapler Pos Adj:1K FIN]
6-141-001 A3 SEF
6-141-002 B4 SEF
6-141-003 A4 SEF
6-141-004 B5 SEF
6-141-005 DLT SEF
6-141-006 LG SEF
6-141-007 Oficio SEF
6-141-008 LT SEF
6-141-009 12"x18"
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
6142 [Sub-scan Punch Pos Adj:1K FIN]
6-142-001 JPN/EU: 2-Hole
6-142-002 NA: 3-Hole
6-142-003 Europe: 4-Hole
6-142-004 NEU: 4-Hole
6-142-005 NA: 2-Hole
ENG [-7.5 to 7.5 / 0 / 0.5mm/step]
ENG
ENG
ENG
ENG
6143 [Jogger Pos Adj:1K FIN]
Engine SP Tables - SP6000
6-143-001 A3 SEF
6-143-002 B4 SEF
6-143-003 A4 SEF
6-143-004 A4 LEF
6-143-005 B5 SEF
6-143-006 B5 LEF
6-143-007 DLT SEF
6-143-008 LG SEF
6-143-009 Oficio SEF
6-143-010 LT SEF
6-143-011 LT LEF
6-143-012 12"x18"
6-143-013 8K SEF
6-143-014 16K SEF
6-143-015 16K LEF
6-143-016 Other
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[-1.5 to 1.5 / 0 / 0.5mm/step]
[-1.5 to 1.5 / 0 / 0.5mm/step]
[-1.5 to 1.5 / 0 / 0.5mm/step]
6144 [Main-scan Punch Pos Adj:1K FIN]
6-144-001 JPN/EU: 2-Hole ENG [-2 to 2 / 0 / 0.4mm/step]
6-144-002 NA: 3-Hole
6-144-003 Europe: 4-Hole
ENG
ENG
6-144-004 NEU: 4-Hole
6-144-005 NA: 2-Hole
ENG
ENG
6145 [Skew Correct Buckle Adj:1K FIN]
405
406
3. Engine SP Mode Tables
6-145-001 A3 SEF
6-145-002 B4 SEF
6-145-003 A4 SEF
6-145-004 A4 LEF
6-145-005 B5 SEF
6-145-006 B5 LEF
6-145-007 A5 LEF
6-145-008 DLT SEF
6-145-009 LG SEF
6-145-010 Oficio SEF
6-145-011 LT SEF
6-145-012 LT LEF
6-145-013 HLT LEF
6-145-014 12"x18"
6-145-015 8K SEF
6-145-016 16K SEF
6-145-017 16K LEF
6-145-018 Other
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[-5 to 5 / 0 / 0.2mm/step]
[-5 to 5 / 0 / 0.2mm/step]
[-5 to 5 / 0 / 0.2mm/step]
ENG
ENG
ENG [-5 to 5 / 0 / 0.2mm/step]
6146 [Skew Correct Ctrl SW:1K FIN]
6-146-001 A3 SEF
6-146-002 B4 SEF
ENG [0 or 1 / 0 / 1/step]
0: enable
1: disable
ENG [0 or 1 / 0 / 1/step]
0: enable
1: disable
6-146-003 A4 SEF
6-146-004 A4 LEF
6-146-005 B5 SEF
6-146-006 B5 LEF
6-146-007 A5 LEF
6-146-008 DLT SEF
6-146-009 LG SEF
6-146-010 Oficio SEF
6-146-011 LT SEF
6-146-012 LT LEF
Engine SP Tables - SP6000
ENG [0 or 1 / 0 / 1/step]
0: enable
1: disable
ENG [0 or 1 / 0 / 1/step]
0: enable
1: disable
ENG [0 or 1 / 0 / 1/step]
0: enable
1: disable
ENG [0 or 1 / 0 / 1/step]
0: enable
1: disable
ENG [0 or 1 / 0 / 1/step]
0: enable
1: disable
ENG [0 or 1 / 0 / 1/step]
0: enable
1: disable
ENG [0 or 1 / 0 / 1/step]
0: enable
1: disable
ENG [0 or 1 / 0 / 1/step]
0: enable
1: disable
ENG [0 or 1 / 0 / 1/step]
0: enable
1: disable
ENG [0 or 1 / 0 / 1/step]
0: enable
1: disable
407
408
3. Engine SP Mode Tables
6-146-013 HLT LEF
6-146-014 12"x18"
6-146-015 8K SEF
6-146-016 16K SEF
6-146-017 16K LEF
6-146-018 Other
ENG [0 or 1 / 0 / 1/step]
0: enable
1: disable
ENG [0 or 1 / 0 / 1/step]
0: enable
1: disable
ENG [0 or 1 / 0 / 1/step]
0: enable
1: disable
ENG [0 or 1 / 0 / 1/step]
0: enable
1: disable
ENG [0 or 1 / 0 / 1/step]
0: enable
1: disable
ENG [0 or 1 / 0 / 1/step]
0: enable
1: disable
6147 [Booklet Folder Pos Adj:1K FIN]
6-147-001 A3 SEF
6-147-002 B4 SEF
6-147-003 A4 SEF
6-147-004 B5 SEF
6-147-005 DLT SEF
6-147-006 LG SEF
6-147-007 Oficio SEF
6-147-008 LT SEF
6-147-009 12"x18"
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
6-147-010 A3 SEF(1-5)
6-147-011 A3 SEF(6-10)
6-147-012 A3 SEF(11-over)
6-147-013 B4 SEF(1-5)
6-147-014 B4 SEF(6-10)
6-147-015 B4 SEF(11-over)
6-147-016 A4 SEF(1-5)
6-147-017 A4 SEF(6-10)
6-147-018 A4 SEF(11-over)
6-147-019 B5 SEF(1-5)
6-147-020 B5 SEF(6-10)
6-147-021 B5 SEF(11-over)
6-147-022 DLT SEF(1-5)
6-147-023 DLT SEF(6-10)
6-147-024 DLT SEF(11-over)
6-147-025 LG SEF(1-5)
6-147-026 LG SEF(6-10)
6-147-027 LG SEF(11-over)
6-147-028 Oficio SEF(1-5)
6-147-029 Oficio SEF(6-10)
6-147-030 Oficio SEF(11-over)
6-147-031 LT SEF(1-5)
6-147-032 LT SEF(6-10)
6-147-033 LT SEF(11-over)
6-147-034 12"x18"(1-5)
6-147-035 12"x18"(6-10)
Engine SP Tables - SP6000
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [-3 to 3 / 0 / 0.2mm/step]
409
410
3. Engine SP Mode Tables
6-147-036 12"x18"(11-over)
6148
6-148-001 -
[Fold Times Adj: 1K FIN]
ENG [-3 to 3 / 0 / 0.2mm/step]
ENG [0 to 29 / 0 / 1sec/step]
6149
6-149-001 -
[Last Paper Pos Time Adj:1K FIN]
*ENG [0 to 1 / 0 / 1time/step]
6150 [PositioningStrtTimingAdj:1KFIN]
6-150-001 A3 SEF
6-150-002 B4 SEF
6-150-003 A4 SEF
6-150-004 A4 LEF
6-150-005 B5 SEF
6-150-006 B5 LEF
6-150-007 DLT SEF
6-150-008 LG SEF
6-150-009 Oficio SEF
6-150-010 LT SEF
6-150-011 LT LEF
6-150-012 12"x18"
6-150-013 8K SEF
6-150-014 16K SEF
6-150-015 16K LEF
6-150-016 Other
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG [-100 to 100 / 0 / 10msec/step]
ENG
ENG
ENG
ENG
6151 [PosTimeAdj(LstPr2ndTime):1KFIN]
Engine SP Tables - SP6000
6-151-001 ENG [-100 to 100 / 0 / 10msec/step]
6152 [PosTiAdj(ExcLstPr3rdTi):1KFIN]
6-152-001 A3 SEF
6-152-002 B4 SEF
6-152-003 A4 SEF
6-152-004 A4 LEF
6-152-005 B5 SEF
6-152-006 B5 LEF
6-152-007 DLT SEF
6-152-008 LG SEF
6-152-009 Oficio SEF
6-152-010 LT SEF
6-152-011 LT LEF
6-152-012 12"x18"
6-152-013 8K SEF
6-152-014 16K SEF
6-152-015 16K LEF
6-152-016 Other
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG [-100 to 100 / 0 / 10msec/step]
ENG
ENG
ENG
ENG
ENG
ENG
ENG
6154 [Pos Time Adj By Sheet: 1K FIN]
6-154-001 1 - 10 Sheets
6-154-002 11 - 20 Sheets
6-154-003 21 - 30 Sheets
6-154-004 31 - 40 Sheets
6-154-005 41 - 50 Sheets
ENG [-100 to 100 / 0 / 10msec/step]
ENG
ENG
ENG
ENG
411
412
3. Engine SP Mode Tables
6155
6-155-001 -
[Paper Guide Poss Adj: 1K FIN]
ENG [-10 to 10 / 0 / 1mm/step]
6156
6-156-001 -
[Paper Guide Retra Adj: 1K FIN]
ENG [-50 to 50 / 0 / 5mm/step]
6157
6-157-001 -
[Paper Guide Acept Adj: 1K FIN]
ENG [-50 to 50 / 0 / 5msec/step]
6160 [Finisher Free Run: 1K FIN]
6-160-001 Free Run 1
6-160-002 Free Run 2
6-160-003 Free Run 3
6-160-004 Free Run 4
ENG
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
6161
6162
[FIN (1K FIN) INPUT Check]
See page 448 "Input Check Table"
[FIN (1K FIN) OUTPUT Check]
See page 475 "Output Check Table"
6163 [Use Paper Guide]
6-163-001 Big Size
6-163-002 Small Size
ENG [0 or 1 / 1 / 1/step]
ENG [0 or 1 / 0 / 1/step]
6164 [NV Adj. Data Mod. 1KShtFIN]
6-164-001 Jogger Pos. Factory Adj.
6-164-002 Stapling Pos. Factory Adj.
6164 [NV Adj. Data Mod. 1KShtFIN HY]
ENG [-1.5 to 1.5 / 0 / 0.5mm/step]
ENG [-2 to 2 / 0 / 0.5mm/step]
Engine SP Tables - SP6000
6-164-003 Stapling Pos. Factory Adj. (HY)
6-164-004 Stapleless Stapling Pos. Factory
Adj.
6164 [NV Adj. Data Mod. 1KShtFIN]
6-164-005 Folding Pos. Factory Adj.
ENG
ENG
[-2.1 to 2.1 / 0 / 0.3mm/step]
[-2.1 to 2.1 / 0 / 0.3mm/step]
ENG [-2 to 2 / 0 / 0.1mm/step]
6180
6-180-001 -
[M-ScanBindPosAdj:NoStplBindFIN]
ENG [-1 to 1 / 0 / 0.5mm/step]
6181
6-181-001 -
[BindSpeedSetting:NoStplBindFIN]
ENG [1 to 3 / 3 / 2/step]
6182 [ExitSpeedSwitch:NoStplBindFIN]
6-182-001 PaperLength:
297.0-457.2mm,Thick(106-300g/m
2
)
6-182-002 PaperLength:
297.0-457.2mm,Plain(60-105g/m
2
)
6-182-003 PaperLength:297.0-457.2mm,Thin(52-59g/m
2
)
6-182-004 PaperLength:
210.0-296.9mm,Thick(106-300g/m
2
)
6-182-005 PaperLength:
210.0-296.9mm,Plain(60-105g/m
2
)
6-182-006 PaperLength:210.0-296.9mm,Thin(52-59g/m
2
)
6-182-007 PaperLength:
148.0-209.9mm,Thick(106-300g/m
2
)
6-182-008 PaperLength:
148.0-209.9mm,Plain(60-105g/m
2
)
6-182-009 PaperLength:148.0-209.9mm,Thin(52-59g/m
2
)
6183 [FinisherFreeRun:NoStplBindFIN]
ENG [1 to 5 / 2 / 1/step]
ENG [1 to 5 / 2 / 1/step]
ENG [1 to 5 / 4 / 1/step]
ENG [1 to 5 / 2 / 1/step]
ENG [1 to 5 / 2 / 1/step]
ENG [1 to 5 / 4 / 1/step]
ENG [1 to 5 / 2 / 1/step]
ENG [1 to 5 / 2 / 1/step]
ENG [1 to 5 / 4 / 1/step]
413
414
3. Engine SP Mode Tables
6-183-001 Free Run 1
6-183-002 Free Run 2
6-183-003 Free Run 3
6184
6185
[Input Check:NoStplBindFIN]
See page 448 "Input Check Table"
[Output Check:NoStplBindFIN]
See page 475 "Output Check Table"
ENG [0 or 1 / 0 / 0/step]
ENG [0 or 1 / 0 / 0/step]
ENG [0 or 1 / 0 / 0/step]
6186
6-186-001 -
[BindTimes NoStplBindFIN]
6801
6-801-001 -
[1-pass Stamp Unit]
*ENG [1 to 2 / 2 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
0: NO
1: YES
6900
6-900-001 -
[ADF Bottom Plate Setting]
*ENG [0 or 1 / 0 / 1/step]
6901
6-901-001 -
[ADF Operation Setting]
Setting to give priority to stackability.
ENG
6-901-002 ENG
[0 or 1 / 0 / 1/step]
0: Higher quietness
1: Higher throughput
[0 or 1 / 0 / 1/step]
0: Normal
1: Higher stackability
Engine SP Tables - SP7000
7621 [PM Counter Display: Pages]
7-621-002 # PCU:K
7-621-003 # Dev Unit:K
7-621-004 Developer:K
7-621-025 # PCU:C
7-621-026 # Dev Unit:C
7-621-027 Developer:C
7-621-048 # PCU:M
7-621-049 # Dev Unit:M
7-621-050 Developer:M
7-621-071 # PCU:Y
7-621-072 # Dev Unit:Y
7-621-073 Developer:Y
7-621-093 # ITB Unit
7-621-102 # ITB Cleaning Unit
7-621-109 # PTR Unit
7-621-115 # Fusing Unit
7-621-116 Fusing Belt
7-621-118 Pressure Roller
7-621-131 Dust Filter
7-621-142 Waste Toner Bottle
7-621-206 ADF Pick-up Roller
ENG [0 to 99999999 / 0 / 1page/step]
*ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
*ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
*ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
*ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 999999999 / 0 / 1mg/step]
ENG [0 to 99999999 / 0 / 1page/step]
415
416
3. Engine SP Mode Tables
7-621-207 ADF Supply Belt
7-621-208 ADF Reverse Roller
7622 [PM Counter Reset]
7-622-002 # PCU:K
7-622-003 # Dev Unit:K
7-622-004 Developer:K
7-622-025 # PCU:C
7-622-026 # Dev Unit:C
7-622-027 Developer:C
7-622-048 # PCU:M
7-622-049 # Dev Unit:M
7-622-050 Developer:M
7-622-071 # PCU:Y
7-622-072 # Dev Unit:Y
7-622-073 Developer:Y
7-622-093 # ITB Unit
7-622-102 # ITB Cleaning Unit
7-622-109 # PTR Unit
7-622-115 # Fusing Unit
7-622-116 Fusing Belt
7-622-118 Pressure Roller
7-622-131 Dust Filter
7-622-206 ADF Pick-up Roller
7-622-207 ADF Supply Belt
7-622-208 ADF Reverse Roller
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
Engine SP Tables - SP7000
7-622-245 PCU:All Colors
7-622-246 Development Unit:All Colors
7-622-247 Developer:All Colors
7-622-250 SCS
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
7623 [PM Value Setting: Life Pages]
7-623-002 # PCU:K
7-623-003 # Dev Unit:K
7-623-004 Developer:K
7-623-025 # PCU:C
7-623-026 # Dev Unit:C
7-623-027 Developer:C
7-623-048 # PCU:M
7-623-049 # Dev Unit:M
7-623-050 Developer:M
7-623-071 # PCU:Y
7-623-072 # Dev Unit:Y
7-623-073 Developer:Y
7-623-093 # ITB Unit
7-623-102 # ITB Cleaning Unit
7-623-109 # PTR Unit
7-623-115 # Fusing Unit
7-623-116 Fusing Belt
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 240000 / 1page/ step]
ENG [0 to 99999999 / 240000 / 1page/ step]
ENG [0 to 99999999 / 240000 / 1page/ step]
ENG [0 to 99999999 / 240000 / 1page/ step]
ENG [0 to 99999999 / 240000 / 1page/ step]
417
418
3. Engine SP Mode Tables
7-623-118 Pressure Roller
7-623-131 Dust Filter
7-623-142 Waste Toner Bottle
7-623-206 ADF Pick-up Roller
7-623-207 ADF Supply Belt
7-623-208
ADF Reverse Roller
ENG [0 to 99999999 / 240000 / 1page/ step]
ENG [0 to 99999999 / 300000 / 1page/ step]
ENG [0 to 999999999 / 1200000 / 1mg/ step]
ENG [0 to 99999999 / 120000 / 1page/ step]
ENG [0 to 99999999 / 120000 / 1page/ step]
ENG
[0 to 99999999 / 120000 / 1page/ step]
7625 [Previous Unit Counter: Pages]
7-625-002 # PCU:K
7-625-003 # Dev Unit:K
7-625-004 Developer:K
7-625-025 # PCU:C
7-625-026 # Dev Unit:C
7-625-027 Developer:C
7-625-048 # PCU:M
7-625-049 # Dev Unit:M
7-625-050 Developer:M
7-625-071 # PCU:Y
7-625-072 # Dev Unit:Y
7-625-073 Developer:Y
7-625-093 # ITB Unit
7-625-102 # ITB Cleaning Unit
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
Engine SP Tables - SP7000
7-625-109 # PTR Unit
7-625-115 # Fusing Unit
7-625-116 Fusing Belt
7-625-118 Pressure Roller
7-625-131 Dust Filter
7-625-142 Waste Toner Bottle
7-625-206 ADF Pick-up Roller
7-625-207 ADF Supply Belt
7-625-208 ADF Reverse Roller
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
7626 [Previous Unit Counter2: Pages]
7-626-002 # PCU:K ENG [0 to 99999999 / 0 / 1page/step]
7-626-003 # Dev Unit:K
7-626-004 Developer:K
7-626-025 # PCU:C
7-626-026 # Dev Unit:C
ENG
ENG
ENG
ENG
[0 to 99999999 / 0 / 1page/step]
[0 to 99999999 / 0 / 1page/step]
[0 to 99999999 / 0 / 1page/step]
[0 to 99999999 / 0 / 1page/step]
7-626-027 Developer:C
7-626-048 # PCU:M
7-626-049 # Dev Unit:M
7-626-050 Developer:M
7-626-071 # PCU:Y
7-626-072 # Dev Unit:Y
7-626-073 Developer:Y
7-626-093 # ITB Unit
7-626-102 # ITB Cleaning Unit
7-626-109 # PTR Unit
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 99999999 / 0 / 1page/step]
[0 to 99999999 / 0 / 1page/step]
[0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
[0 to 99999999 / 0 / 1page/step]
[0 to 99999999 / 0 / 1page/step]
[0 to 99999999 / 0 / 1page/step]
[0 to 99999999 / 0 / 1page/step]
419
420
3. Engine SP Mode Tables
7-626-115 # Fusing Unit
7-626-116 Fusing Belt
7-626-118 Pressure Roller
7-626-131 Dust Filter
7-626-142 Waste Toner Bottle
7-626-206 ADF Pick-up Roller
7-626-207 ADF Supply Belt
7-626-208 ADF Reverse Roller
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 999999999 / 0 / 1mg/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
ENG [0 to 99999999 / 0 / 1page/step]
7628 [PM Counter Reset]
7-628-002 SCS
7720 [Ave. Cvrg for Eng.]
7-720-001 K
7-720-002 C
7-720-003 M
7-720-004 Y
ENG [0 or 1 / 0 / 1/step]
*ENG [0 to 100 / 0 / 0.01%/step]
*ENG [0 to 100 / 0 / 0.01%/step]
*ENG [0 to 100 / 0 / 0.01%/step]
*ENG [0 to 100 / 0 / 0.01%/step]
7801 [ROM No.]
7-801-002 Engine
7-801-005 ADF
7-801-007 Finisher
7-801-009 PTU
7-801-010 LCT
7-801-019 PTU2
7801 [ROM No./ Firmware Version]
7-801-102 Engine
ENG [- / - / -]
ENG [- / - / -]
ENG [- / - / -]
ENG [- / - / -]
ENG [- / - / -]
ENG [- / - / -]
ENG [- / - / -]
Engine SP Tables - SP7000
7-801-105 ADF
7-801-107 Finisher
7-801-109 PTU
7-801-110 LCT
ENG [- / - / -]
ENG [- / - / -]
ENG [- / - / -]
ENG [- / - / -]
7852 [DF Glass Dust Check]
7-852-001 Dust Detection Counter
7-852-002 Dust Counter Clear Counter
*ENG
*ENG
[0 to 65535 / 0 / 1/step]
[0 to 65535 / 0 / 1/step]
7-852-003 Dust Detection Counter: Back *ENG [0 to 65535 / 0 / 1/step]
7853 [Replace Counter]
7-853-002 # PCU:K
7-853-003 # Dev Unit:K
7-853-004 Developer:K
7-853-025 # PCU:C
7-853-026 # Dev Unit:C
7-853-027 Developer:C
7-853-048 # PCU:M
7-853-049 # Dev Unit:M
7-853-050 Developer:M
7-853-071 # PCU:Y
7-853-072 # Dev Unit:Y
7-853-073 Developer:Y
7-853-093 # ITB Unit
7-853-102 # ITB Cleaning Unit
7-853-109 # PTR Unit
7-853-115 # Fusing Unit
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 255 / 0 / 1/step]
[0 to 255 / 0 / 1/step]
[0 to 255 / 0 / 1/step]
[0 to 255 / 0 / 1/step]
[0 to 255 / 0 / 1/step]
[0 to 255 / 0 / 1/step]
[0 to 255 / 0 / 1/step]
[0 to 255 / 0 / 1/step]
[0 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
[0 to 255 / 0 / 1/step]
[0 to 255 / 0 / 1/step]
[0 to 255 / 0 / 1/step]
[0 to 255 / 0 / 1/step]
[0 to 255 / 0 / 1/step]
421
422
3. Engine SP Mode Tables
7-853-116 Fusing Belt
7-853-118 Pressure Roller
7-853-131 Dust Filter
7-853-142 Waste Toner Bottle
7-853-206 ADF Pick-up Roller
7-853-207 ADF Supply Belt
7-853-208 ADF Reverse Roller
ENG [0 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
ENG [0 to 255 / 0 / 1/step]
7906 [Previous Unit Counter:Distance]
7-906-002 # PCU:K
7-906-003 # Dev Unit:K
7-906-004 Developer:K
ENG [0 to 4294967295 / 0 / 1mm/step]
ENG [0 to 4294967295 / 0 / 1mm/step]
ENG [0 to 4294967295 / 0 / 1mm/step]
7-906-025 # PCU:C
7-906-026 # Dev Unit:C
7-906-027 Developer: C
7-906-048 # PCU:M
7-906-049 # Dev Unit:M
7-906-050 Developer: M
7-906-071 # PCU:Y
7-906-072 # Dev Unit:Y
7-906-073 Developer: Y
7-906-093 # ITB Unit
7-906-102 # ITB Cleaning Unit
7-906-109 # PTR Unit
7-906-115 # Fusing Unit
7-906-116 Fusing Belt
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
ENG [0 to 4294967295 / 0 / 1mm/step]
ENG [0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
Engine SP Tables - SP7000
7-906-118 Pressure Roller
7-906-230 Low Speed: # PCU:K
7-906-231 Low Speed: # PCU:C
7-906-232 Low Speed: # PCU:M
7-906-233 Low Speed: # PCU:Y
7-906-234 Middle Speed: # PCU:K
7-906-235 Middle Speed: # PCU:C
7-906-236 Middle Speed: # PCU:M
7-906-237 Middle Speed: # PCU:Y
ENG [0 to 4294967295 / 0 / 1mm/step]
ENG [0 to 4294967295 / 0 / 1mm/step]
ENG [0 to 4294967295 / 0 / 1mm/step]
ENG [0 to 4294967295 / 0 / 1mm/step]
ENG [0 to 4294967295 / 0 / 1mm/step]
ENG [0 to 4294967295 / 0 / 1mm/step]
ENG [0 to 4294967295 / 0 / 1mm/step]
ENG [0 to 4294967295 / 0 / 1mm/step]
ENG [0 to 4294967295 / 0 / 1mm/step]
7907 [Previous Unit Cntr:Distance(%)]
7-907-002 # PCU:K
7-907-003 # Dev Unit:K
7-907-004 Developer:K
7-907-025 # PCU:C
7-907-026 # Dev Unit:C
7-907-027 Developer:C
7-907-048 # PCU:M
7-907-049 # Dev Unit:M
7-907-050 Developer:M
7-907-071 # PCU:Y
7-907-072 # Dev Unit:Y
7-907-073 Developer:Y
7-907-093 # ITB Unit
7-907-102 # ITB Cleaning Unit
7-907-109 # PTR Unit
ENG [0 to 255 / 0 / 1%/step]
ENG [0 to 255 / 0 / 1%/step]
ENG [0 to 255 / 0 / 1%/step]
ENG [0 to 255 / 0 / 1%/step]
ENG [0 to 255 / 0 / 1%/step]
ENG [0 to 255 / 0 / 1%/step]
ENG [0 to 255 / 0 / 1%/step]
ENG [0 to 255 / 0 / 1%/step]
ENG [0 to 255 / 0 / 1%/step]
ENG [0 to 255 / 0 / 1%/step]
ENG [0 to 255 / 0 / 1%/step]
ENG [0 to 255 / 0 / 1%/step]
ENG [0 to 255 / 0 / 1%/step]
ENG [0 to 255 / 0 / 1%/step]
ENG [0 to 255 / 0 / 1%/step]
423
424
3. Engine SP Mode Tables
7-907-115 # Fusing Unit
7-907-116 Fusing Belt
7-907-118 Pressure Roller
ENG [0 to 255 / 0 / 1%/step]
ENG [0 to 255 / 0 / 1%/step]
ENG [0 to 255 / 0 / 1%/step]
7908 [Previous Unit Counter:Pages(%)]
7-908-002 # PCU:K ENG [0 to 255 / 0 / 1%/step]
7-908-003 # Dev Unit:K
7-908-004 Developer:K
ENG [0 to 255 / 0 / 1%/step]
ENG [0 to 255 / 0 / 1%/step]
7-908-025 # PCU:C
7-908-026 # Dev Unit:C
7-908-027 Developer:C
7-908-048 # PCU:M
ENG
ENG
ENG
ENG
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
7-908-049 # Dev Unit:M
7-908-050 Developer:M
7-908-071 # PCU:Y
7-908-072 # Dev Unit:Y
7-908-073 Developer:Y
7-908-093 # ITB Unit
7-908-102 # ITB Cleaning Unit
7-908-109 # PTR Unit
7-908-115 # Fusing Unit
7-908-116 Fusing Belt
7-908-118 Pressure Roller
7-908-131 Dust Filter
7-908-142 Waste Toner Bottle
7-908-206 ADF Pick-up Roller
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
ENG [0 to 255 / 0 / 1%/step]
ENG [0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
Engine SP Tables - SP7000
7-908-207 ADF Supply Belt
7-908-208 ADF Reverse Roller
7931 [Toner Bottle Bk]
7-931-001 Machine Serial ID
7-931-002 Cartridge Ver
7-931-003 Brand ID
7-931-004 Area ID
7-931-005 Product ID
7-931-006 Color ID
7-931-007 Maintenance ID
7-931-008 New Product Information
7-931-009 Recycle Counter
7-931-010 Date
7-931-011 SerialNo.
7-931-012 Toner Remaining
7-931-013 EDP Code
7-931-014 End History
7-931-015 Refill Information
7-931-016 Attachment: Total Counter
7-931-017 Attachment: Color Counter
7-931-018 End: Total Counter
7-931-019 End: Color Counter
7-931-020 Attachment Date
7-931-021 End Date
7932 [Toner Bottle M]
ENG
ENG
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 100 / 100 / 1%/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
425
426
3. Engine SP Mode Tables
7-932-001 Machine Serial ID
7-932-002 Cartridge Ver
7-932-003 Brand ID
7-932-004 Area ID
7-932-005 Product ID
7-932-006 Color ID
7-932-007 Maintenance ID
7-932-008 New Product Information
7-932-009 Recycle Counter
7-932-010 Date
7-932-011 SerialNo.
7-932-012 Toner Remaining
7-932-013 EDP Code
7-932-014 End History
7-932-015 Refill Information
7-932-016 Attachment: Total Counter
7-932-017 Attachment: Color Counter
7-932-018 End: Total Counter
7-932-019 End: Color Counter
7-932-020 Attachment Date
7-932-021 End Date
7933 [Toner Bottle C]
7-933-001 MachineSerialID
7-933-002 Cartridge Ver
7-933-003 Brand ID
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 100 / 100 / 1%/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
Engine SP Tables - SP7000
7-933-004 Area ID
7-933-005 Product ID
7-933-006 Color ID
7-933-007 Maintenance ID
7-933-008 New Product Information
7-933-009 Recycle Counter
7-933-010 Date
7-933-011 SerialNo.
7-933-012 Toner Remaining
7-933-013 EDP Code
7-933-014 End History
7-933-015 Refill Information
7-933-016 Attachment: Total Counter
7-933-017 Attachment: Color Counter
7-933-018 End: Total Counter
7-933-019 End: Color Counter
7-933-020 Attachment Date
7-933-021 End Date
7934 [Toner Bottle Y]
7-934-001 MachineSerialID
7-934-002 Cartridge Ver
7-934-003 Brand ID
7-934-004 Area ID
7-934-005 Product ID
7-934-006 Color ID
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 100 / 100 / 1%/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
427
428
3. Engine SP Mode Tables
7-934-007 Maintenance ID
7-934-008 New Product Information
7-934-009 Recycle Counter
7-934-010 Date
7-934-011 SerialNo.
7-934-012 Toner Remaining
7-934-013 EDP Code
7-934-014 End History
7-934-015 Refill Information
7-934-016 Attachment: Total Counter
7-934-017 Attachment: Color Counter
7-934-018 End: Total Counter
7-934-019 End: Color Counter
7-934-020 Attachment Date
7-934-021 End Date
7935 [Toner Bottle Log 1: Bk]
7-935-001 SerialNo.
7-935-002 Attachment Date
7-935-003 Attachment: Total Counter
7-935-004 Refill Information
7935 [Toner Bottle Log 2: Bk]
7-935-011 SerialNo.
7-935-012 Attachment Date
7-935-013 Attachment: Total Counter
7-935-014 Refill Information
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 255 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 100 / 100 / 1%/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
*ENG [0 to 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
Engine SP Tables - SP7000
7935 [Toner Bottle Log 3: Bk]
7-935-021 SerialNo.
7-935-022 Attachment Date
7-935-023 Attachment: Total Counter
7-935-024 Refill Information
7935 [Toner Bottle Log 4: Bk]
7-935-031 SerialNo.
7-935-032 Attachment Date
7-935-033 Attachment: Total Counter
7-935-034 Refill Information
7935 [Toner Bottle Log 5: Bk]
7-935-041 SerialNo.
7-935-042 Attachment Date
7-935-043 Attachment: Total Counter
7-935-044 Refill Information
7936 [Toner Bottle Log 1: M]
7-936-001 SerialNo.
7-936-002 Attachment Date
7-936-003 Attachment: Total Counter
7-936-004 Refill Information
7936 [Toner Bottle Log 2: M]
7-936-011 SerialNo.
7-936-012 Attachment Date
7-936-013 Attachment: Total Counter
7-936-014 Refill Information
ENG
ENG
ENG
*ENG
ENG
ENG
ENG
*ENG
ENG
ENG
ENG
*ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
429
430
3. Engine SP Mode Tables
7936 [Toner Bottle Log 3: M]
7-936-021 SerialNo.
7-936-022 Attachment Date
7-936-023 Attachment: Total Counter
7-936-024 Refill Information
7936 [Toner Bottle Log 4: M]
7-936-031 SerialNo.
7-936-032 Attachment Date
7-936-033 Attachment: Total Counter
7-936-034 Refill Information
7936 [Toner Bottle Log 5: M]
7-936-041 SerialNo.
7-936-042 Attachment Date
7-936-043 Attachment: Total Counter
7-936-044 Refill Information
7937 [Toner Bottle Log 1: C]
7-937-001 SerialNo.
7-937-002 Attachment Date
7-937-003 Attachment: Total Counter
7-937-004 Refill Information
7937 [Toner Bottle Log 2: C]
7-937-011 SerialNo.
7-937-012 Attachment Date
7-937-013 Attachment: Total Counter
7-937-014 Refill Information
ENG
ENG
ENG
*ENG
ENG
ENG
ENG
*ENG
ENG
ENG
ENG
*ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
Engine SP Tables - SP7000
7937 [Toner Bottle Log 3: C]
7-937-021 SerialNo.
7-937-022 Attachment Date
7-937-023 Attachment: Total Counter
7-937-024 Refill Information
7937 [Toner Bottle Log 4: C]
7-937-031 SerialNo.
7-937-032 Attachment Date
7-937-033 Attachment: Total Counter
7-937-034 Refill Information
7937 [Toner Bottle Log 5: C]
7-937-041 SerialNo.
7-937-042 Attachment Date
7-937-043 Attachment: Total Counter
7-937-044 Refill Information
7938 [Toner Bottle Log 1: Y]
7-938-001 SerialNo.
7-938-002 Attachment Date
7-938-003 Attachment: Total Counter
7-938-004 Refill Information
7938 [Toner Bottle Log 2: Y]
7-938-011 SerialNo.
7-938-012 Attachment Date
7-938-013 Attachment: Total Counter
7-938-014 Refill Information
7938 [Toner Bottle Log 3: Y]
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
431
432
3. Engine SP Mode Tables
7-938-021 SerialNo.
7-938-022 Attachment Date
7-938-023 Attachment: Total Counter
7-938-024 Refill Information
7938 [Toner Bottle Log 4: Y]
7-938-031 SerialNo.
7-938-032 Attachment Date
7-938-033 Attachment: Total Counter
7-938-034 Refill Information
7938 [Toner Bottle Log 5: Y]
7-938-041 SerialNo.
7-938-042 Attachment Date
7-938-043 Attachment: Total Counter
7-938-044 Refill Information
ENG
ENG
ENG
*ENG [0 or 1 / 0 / 1/step]
ENG
ENG
ENG
*ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
ENG [0 to 99999999 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
7940 [PM Value Setting:Life Distance]
7-940-002 # PCU:K ENG
7-940-003 # Dev Unit:K
7-940-004 Developer:K
7-940-025 # PCU:C
7-940-026 # Dev Unit:C
ENG
ENG
ENG
ENG
7-940-027 Developer:C
7-940-048 # PCU:M
7-940-049 # Dev Unit:M
7-940-050 Developer:M
7-940-071 # PCU:Y
ENG
ENG
ENG
ENG
ENG
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
Engine SP Tables - SP7000
7-940-072 # Dev Unit:Y
7-940-073 Developer:Y
7-940-093 # ITB Unit
7-940-102 # ITB Cleaning Unit
7-940-109 # PTR Unit
7-940-115 # Fusing Unit
7-940-116 Fusing Belt
7-940-118 Pressure Roller
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 128410397 /
1mm/step]
[0 to 999999999 / 128410397 /
1mm/step]
[0 to 999999999 / 128410397 /
1mm/step]
[0 to 999999999 / 291305000 /
1mm/step]
[0 to 999999999 / 291305000 /
1mm/step]
[0 to 999999999 / 291305000 /
1mm/step]
7942 [PM Counter Display:Distance(%)]
7-942-002 # PCU:K ENG
7-942-003 # Dev Unit:K
7-942-004 Developer:K
7-942-025 # PCU:C
7-942-026 # Dev Unit:C
7-942-027 Developer:C
ENG
ENG
ENG
ENG
ENG
7-942-048 # PCU:M
7-942-049 # Dev Unit:M
7-942-050 Developer:M
7-942-071 # PCU:Y
7-942-072 # Dev Unit:Y
7-942-073 Developer:Y
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
433
434
3. Engine SP Mode Tables
7-942-093 # ITB Unit
7-942-102 # ITB Cleaning Unit
7-942-109 # PTR Unit
7-942-115 # Fusing Unit
7-942-116 Fusing Belt
7-942-118 Pressure Roller
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
7944 [PM Counter Display: Distance]
7-944-002 # PCU:K *ENG [0 to 4294967295 / 0 / 1mm/step]
7-944-003 # Dev Unit:K
7-944-004 Developer:K
7-944-025 # PCU:C
*ENG [0 to 4294967295 / 0 / 1mm/step]
*ENG [0 to 4294967295 / 0 / 1mm/step]
*ENG [0 to 4294967295 / 0 / 1mm/step]
7-944-026 # Dev Unit:C
7-944-027 Developer:C
7-944-048 # PCU:M
7-944-049 # Dev Unit:M
*ENG [0 to 4294967295 / 0 / 1mm/step]
*ENG [0 to 4294967295 / 0 / 1mm/step]
*ENG [0 to 4294967295 / 0 / 1mm/step]
*ENG [0 to 4294967295 / 0 / 1mm/step]
7-944-050 Developer:M
7-944-071 # PCU:Y
7-944-072 # Dev Unit:Y
7-944-073 Developer:Y
7-944-093 # ITB Unit
7-944-102 # ITB Cleaning Unit
7-944-109 # PTR Unit
7-944-115 # Fusing Unit
7-944-116 Fusing Belt
7-944-118 Pressure Roller
*ENG
*ENG
*ENG
ENG
ENG
ENG
ENG
ENG
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
*ENG [0 to 4294967295 / 0 / 1mm/step]
*ENG [0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
Engine SP Tables - SP7000
7-944-230 Low Speed: # PCU:K
7-944-231 Low Speed: # PCU:C
7-944-232 Low Speed: # PCU:M
7-944-233 Low Speed: # PCU:Y
7-944-234 Middle Speed: # PCU:K
7-944-235 Middle Speed: # PCU:C
7-944-236 Middle Speed: # PCU:M
7-944-237 Middle Speed: # PCU:Y
7950 [Unit Replacement Date]
7-950-002 # PCU:K
7-950-003 # Dev Unit:K
7-950-004 Developer:K
7-950-025 # PCU:C
7-950-026 # Dev Unit:C
7-950-027 Developer:C
7-950-048 # PCU:M
7-950-049 # Dev Unit:M
7-950-050 Developer:M
7-950-071 # PCU:Y
7-950-072 # Dev Unit:Y
7-950-073 Developer:Y
7-950-093 # ITB Unit
7-950-102 # ITB Cleaning Unit
7-950-109 # PTR Unit
7-950-115 # Fusing Unit
7-950-116 Fusing Belt
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
*ENG [- / 0 / -]
*ENG [- / 0 / -]
*ENG [- / 0 / -]
*ENG [- / 0 / -]
*ENG [- / 0 / -]
*ENG [- / 0 / -]
*ENG [- / 0 / -]
*ENG [- / 0 / -]
*ENG [- / 0 / -]
*ENG [- / 0 / -]
*ENG [- / 0 / -]
*ENG [- / 0 / -]
*ENG [- / 0 / -]
*ENG [- / 0 / -]
*ENG [- / 0 / -]
*ENG [- / 0 / -]
*ENG [- / 0 / -]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
[0 to 4294967295 / 0 / 1mm/step]
435
436
3. Engine SP Mode Tables
7-950-118 Pressure Roller
7-950-131 Dust Filter
7-950-142 Waste Toner Bottle
7-950-206 ADF Pick-up Roller
7-950-207 ADF Supply Belt
7-950-208 ADF Reverse Roller
*ENG [- / 0 / -]
*ENG [- / 0 / -]
*ENG [- / 0 / -]
*ENG [- / 0 / -]
*ENG [- / 0 / -]
*ENG [- / 0 / -]
7951 [Remain Day Counter: Pages]
7-951-002 # PCU:K
7-951-003 # Dev Unit:K
7-951-004 Developer:K
7-951-025 # PCU:C
7-951-026 # Dev Unit:C
7-951-027 Developer:C
7-951-048 # PCU:M
7-951-049 # Dev Unit:M
7-951-050 Developer:M
7-951-071 # PCU:Y
7-951-072 # Dev Unit:Y
7-951-073 Developer:Y
7-951-093 # ITB Unit
7-951-102 # ITB Cleaning Unit
7-951-109 # PTR Unit
7-951-115 # Fusing Unit
7-951-116 Fusing Belt
7-951-118 Pressure Roller
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
Engine SP Tables - SP7000
7-951-131 Dust Filter
7-951-142 Waste Toner Bottle
7-951-206 ADF Pick-up Roller
7-951-207 ADF Supply Belt
7-951-208 ADF Reverse Roller
7952 [Remain Day Counter: Distance]
7-952-002 # PCU:K ENG
7-952-003 # Dev Unit:K
7-952-004 Developer:K
7-952-025 # PCU:C
7-952-026 # Dev Unit:C
ENG
ENG
ENG
ENG
7-952-027 Developer:C
7-952-048 # PCU:M
7-952-049 # Dev Unit:M
7-952-050 Developer:M
ENG
ENG
ENG
ENG
7-952-071 # PCU:Y
7-952-072 # Dev Unit:Y
7-952-073 Developer:Y
7-952-093 # ITB Unit
7-952-102 # ITB Cleaning Unit
7-952-109 # PTR Unit
7-952-115 # Fusing Unit
7-952-116 Fusing Belt
7-952-118 Pressure Roller
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
7953 [Operation Env. Log: PCU: K]
ENG
ENG
ENG
ENG
ENG
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
437
438
3. Engine SP Mode Tables
7-953-001 T<=0
7-953-002 0<T<=5:0<=H<30
7-953-003 0<T<=5:30<=H<70
7-953-004 0<T<=5:70<=H<=100
7-953-005 5<T<15:0<=H<30
7-953-006 5<T<15:30<=H<55
7-953-007 5<T<15:55<=H<80
7-953-008 5<T<15:80<=H<=100
7-953-009 15<=T<25:0<=H<30
7-953-010 15<=T<25:30<=H<55
7-953-011 15<=T<25:55<=H<80
7-953-012 15<=T<25:80<=H<=100
7-953-013 25<=T<30:0<=H<30
7-953-014 25<=T<30:30<=H<55
7-953-015 25<=T<30:55<=H<80
7-953-016 25<=T<30:80<=H<=100
7-953-017 30<=T:0<=H<30
7-953-018 30<=T:30<=H<55
7-953-019 30<=T:55<=H<80
7-953-020 30<=T:80<=H<=100
7-953-021 35<=T:0<=H<=100
7953 [Operation Env. Log Clear]
7-953-100
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
[0 to 999999999 / 0 / 1mm/step]
ENG [0 to 1 / 0 / 1/step]
7954 [PM Counter Display: Pages (%)]
7-954-002 # PCU:K ENG [0 to 255 / 0 / 1%/step]
Engine SP Tables - SP7000
7-954-003 # Dev Unit:K
7-954-004 Developer:K
7-954-025 # PCU:C
7-954-026 # Dev Unit:C
7-954-027 Developer:C
7-954-048 # PCU:M
7-954-049 # Dev Unit:M
7-954-050 Developer:M
7-954-071 # PCU:Y
7-954-072 # Dev Unit:Y
7-954-073 Developer:Y
7-954-093 # ITB Unit
7-954-102 # ITB Cleaning Unit
7-954-109 # PTR Unit
7-954-115 # Fusing Unit
7-954-116 Fusing Belt
7-954-118 Pressure Roller
7-954-131 Dust Filter
7-954-142 Waste Toner Bottle
7-954-206 ADF Pick-up Roller
7-954-207 ADF Supply Belt
7-954-208 ADF Reverse Roller
7955 [Estimated Remain Pages]
7-955-002 # PCU:K
7-955-003 # Dev Unit:K
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
439
440
3. Engine SP Mode Tables
7-955-004 Developer:K
7-955-025 # PCU:C
7-955-026 # Dev Unit:C
7-955-027 Developer:C
7-955-048 # PCU:M
7-955-049 # Dev Unit:M
7-955-050 Developer:M
7-955-071 # PCU:Y
7-955-072 # Dev Unit:Y
7-955-073 Developer:Y
7-955-093 # ITB Unit
7-955-102 # ITB Cleaning Unit
7-955-109 # PTR Unit
7-955-115 # Fusing Unit
7-955-116 Fusing Belt
7-955-118 Pressure Roller
7956 [Estimated Remain Days]
7-956-002 # PCU:K
7-956-003 # Dev Unit:K
7-956-004 Developer:K
7-956-025 # PCU:C
7-956-026 # Dev Unit:C
7-956-027 Developer:C
7-956-048 # PCU:M
7-956-049 # Dev Unit:M
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
Engine SP Tables - SP7000
7-956-050 Developer:M
7-956-071 # PCU:Y
7-956-072 # Dev Unit:Y
7-956-073 Developer:Y
7-956-093 # ITB Unit
7-956-102 # ITB Cleaning Unit
7-956-109 # PTR Unit
7-956-115 # Fusing Unit
7-956-116 Fusing Belt
7-956-118 Pressure Roller
7-956-131 Dust Filter
7-956-142 Waste Toner Bottle
7-956-206 ADF Pick-up Roller
7-956-207 ADF Supply Belt
7-956-208 ADF Reverse Roller
7957 [Monthly Average Pages]
7-957-002 # PCU:K
7-957-003 # Dev Unit:K
7-957-004 Developer:K
7-957-025 # PCU:C
7-957-026 # Dev Unit:C
7-957-027 Developer:C
7-957-048 # PCU:M
7-957-049 # Dev Unit:M
7-957-050 Developer:M
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
[0 to 255 / 255 / 1day/step]
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
441
442
3. Engine SP Mode Tables
7-957-071 # PCU:Y
7-957-072 # Dev Unit:Y
7-957-073 Developer:Y
7-957-093 # ITB Unit
7-957-102 # ITB Cleaning Unit
7-957-109 # PTR Unit
7-957-115 # Fusing Unit
7-957-116 Fusing Belt
7-957-118 Pressure Roller
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
[0 to 9999999 / 0 / 1page/step]
7958 [PM Value Setting:DaysThreshold]
7-958-002 # PCU:K ENG
7-958-003 # Dev Unit:K
7-958-004 Developer:K
7-958-025 # PCU:C
7-958-026 # Dev Unit:C
ENG
ENG
ENG
ENG
7-958-027 Developer:C
7-958-048 # PCU:M
7-958-049 # Dev Unit:M
7-958-050 Developer:M
7-958-071 # PCU:Y
7-958-072 # Dev Unit:Y
7-958-073 Developer:Y
7-958-093 # ITB Unit
7-958-102 # ITB Cleaning Unit
7-958-109 # PTR Unit
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
7-958-115 # Fusing Unit
7-958-116 Fusing Belt
7-958-118 Pressure Roller
7-958-131 Dust Filter
7-958-142 Waste Toner Bottle
7-958-206 ADF Pick-up Roller
7-958-207 ADF Supply Belt
7-958-208 ADF Reverse Roller
7959 [Fusing: Stop]
7-959-001 Near End: Page
7-959-002 End: Page
7-959-003 Near End: Rotation
7-959-004 End: Rotation
7960 [Estimated Usage Rate]
7-960-002 # PCU:K
7-960-003 # Dev Unit:K
7-960-004 Developer:K
7-960-025 # PCU:C
7-960-026 # Dev Unit:C
7-960-027 Developer:C
7-960-048 # PCU:M
7-960-049 # Dev Unit:M
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
Engine SP Tables - SP7000
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
[1 to 30 / 15 / 1day/step]
ENG
ENG
ENG
ENG
[0 to 99999999 / 244000 / 1page/ step]
[0 to 99999999 / 248000 / 1page/ step]
[0 to 999999999 / 302229000 /
1mm/step]
[0 to 999999999 / 313153000 /
1mm/step]
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
443
444
3. Engine SP Mode Tables
7-960-050 Developer:M
7-960-071 # PCU:Y
7-960-072 # Dev Unit:Y
7-960-073 Developer:Y
7-960-093 # ITB Unit
7-960-102 # ITB Cleaning Unit
7-960-109 # PTR Unit
7-960-115 # Fusing Unit
7-960-116 Fusing Belt
7-960-118 Pressure Roller
7-960-131 Dust Filter
7-960-142 Waste Toner Bottle
7-960-206 ADF Pick-up Roller
7-960-207 ADF Supply Belt
7-960-208 ADF Reverse Roller
7979 [ENG Reset Log]
7-979-001 Data1
7-979-002 Data2
7-979-003 Data3
7-979-004 Data4
7-979-005 Data5
7-979-006 Data6
7-979-007 Data7
7-979-008 Data8
7-979-009 Data9
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
[0 to 255 / 0 / 1%/step]
*ENG [0x00 to 0xFF / 0x00 / 1/step]
*ENG [0x0000 to 0xFFFF / 0x0000 / 1/step]
*ENG [0x0000 to 0xFFFF / 0x0000 / 1/step]
*ENG [0x0000 to 0xFFFF / 0x0000 / 1/step]
*ENG [0x0000 to 0xFFFF / 0x0000 / 1/step]
*ENG [0x0000 to 0xFFFF / 0x0000 / 1/step]
*ENG [0x0000 to 0xFFFF / 0x0000 / 1/step]
*ENG [0x0000 to 0xFFFF / 0x0000 / 1/step]
*ENG [0x0000 to 0xFFFF / 0x0000 / 1/step]
Engine SP Tables - SP7000
7-979-010 Data10
7-979-011 Data11
7-979-012 Data12
7-979-013 Data13
7-979-014 Data14
7-979-015 Data15
7-979-016 Data16
7-979-017 Data17
7-979-018 Data18
7-979-019 Data19
7-979-020 Data20
7-979-021 Data21
*ENG
*ENG
[0x0000 to 0xFFFF / 0x0000 / 1/step]
*ENG [0x0000 to 0xFFFF / 0x0000 / 1/step]
*ENG [0x0000 to 0xFFFF / 0x0000 / 1/step]
*ENG [0x0000 to 0xFFFF / 0x0000 / 1/step]
*ENG [0x0000 to 0xFFFF / 0x0000 / 1/step]
*ENG [0x0000 to 0xFFFF / 0x0000 / 1/step]
*ENG [0x0000 to 0xFFFF / 0x0000 / 1/step]
*ENG [0x0000 to 0xFFFF / 0x0000 / 1/step]
[0x0000 to 0xFFFF / 0x0000 / 1/step]
*ENG [0x0000 to 0xFFFF / 0x0000 / 1/step]
*ENG [0x0000 to 0xFFFF / 0x0000 / 1/step]
*ENG [0x0000 to 0xFFFF / 0x0000 / 1/step]
7980 [Current for Torque Calculation]
7-980-001 OPCTransferMotor
7-980-002 BkDevMotor
*ENG [0 to 9.999 / 0 / 0.001A/step]
*ENG [0 to 9.999 / 0 / 0.001A/step]
7-980-003 ColorOpcMotor
7-980-004 ColorDevMotor
7-980-005 FusingMotor
*ENG
*ENG
*ENG
[0 to 9.999 / 0 / 0.001A/step]
[0 to 9.999 / 0 / 0.001A/step]
[0 to 9.999 / 0 / 0.001A/step]
7981 [Edict:OffsetValueForTorqCalcu]
7-981-001 ManualExe ENG [0 or 1 / 0 / 1/step]
7982 [OffsetValueForTorqCalculation]
7-982-001 OPCTransferMotor *ENG [0 to 655.35 / 0 / 0.01/step]
7-982-002 BkDevMotor
7-982-003 ColorOpcMotor
*ENG [0 to 655.35 / 0 / 0.01/step]
*ENG [0 to 655.35 / 0 / 0.01/step]
445
446
3. Engine SP Mode Tables
7-982-004 ColorDevMotor
7-982-005 FusingMotor
7983 [OutputLevel1CountNo.]
7-983-001 OPCTransferMotor
7-983-002 BkDevMotor
7-983-003 ColorOpcMotor
7-983-004 ColorDevMotor
7-983-005 FusingMotor
7984 [OutputLevel2CountNo.]
7-984-001 OPCTransferMotor
7-984-002 BkDevMotor
7-984-003 ColorOpcMotor
7-984-004 ColorDevMotor
7-984-005 FusingMotor
7985 [OutputLevel3CountNo.]
7-985-001 OPCTransferMotor
7-985-002 BkDevMotor
7-985-003 ColorOpcMotor
7-985-004 ColorDevMotor
7-985-005 FusingMotor
7986 [VelocityErr.CountNo.]
7-986-001 OPCTransferMotor
7-986-002 BkDevMotor
*ENG [0 to 655.35 / 0 / 0.01/step]
*ENG [0 to 655.35 / 0 / 0.01/step]
*ENG [0 to 65535 / 0 / 1count/step]
*ENG [0 to 65535 / 0 / 1count/step]
*ENG [0 to 65535 / 0 / 1count/step]
*ENG [0 to 65535 / 0 / 1count/step]
*ENG [0 to 65535 / 0 / 1count/step]
*ENG [0 to 65535 / 0 / 1count/step]
*ENG [0 to 65535 / 0 / 1count/step]
*ENG [0 to 65535 / 0 / 1count/step]
*ENG [0 to 65535 / 0 / 1count/step]
*ENG [0 to 65535 / 0 / 1count/step]
*ENG [0 to 65535 / 0 / 1count/step]
*ENG [0 to 65535 / 0 / 1count/step]
*ENG [0 to 65535 / 0 / 1count/step]
*ENG [0 to 65535 / 0 / 1count/step]
*ENG [0 to 65535 / 0 / 1count/step]
*ENG [0 to 65535 / 0 / 1count/step]
*ENG [0 to 65535 / 0 / 1count/step]
7-986-003 ColorOpcMotor
7-986-004 ColorDevMotor
7-986-005 FusingMotor
Engine SP Tables - SP7000
*ENG [0 to 65535 / 0 / 1count/step]
*ENG [0 to 65535 / 0 / 1count/step]
*ENG [0 to 65535 / 0 / 1count/step]
447
448
3. Engine SP Mode Tables
5803 [INPUT Check]
5-803-001 Registration Sensor ENG [0 or 1 / 0 / 1/step]
0: paper exist
1: paper non exist
Responds to paper existence on register sensor position.
(0: paper exist, 1: paper non exist)
ENG 5-803-002 Paper Feed Sensor 1
This setting is not available for
MP C2004/MP C2504.
[0 or 1 / 0 / 1/step]
0: paper exist
1: paper non exist
Responds to paper existence on 1st paper feed sensor position.
(0: paper exist, 1: paper non exist)
5-803-003 Transport Sensor 1 ENG [0 or 1 / 0 / 1/step]
0: paper exist
1: paper non exist
Responds to paper existence on 1st carry sensor position.
(0: paper exist, 1: paper non exist)
ENG 5-803-004 Paper Feed Sensor 2
This setting is not available for
MP C2004/MP C2504.
[0 or 1 / 0 / 1/step]
0: paper exist
1: paper non exist
Responds to paper existence on 2nd paper feed sensor position.
(0: paper exist, 1: paper non exist)
Input and Output Check
5-803-005 Transport Sensor 2 ENG [0 or 1 / 0 / 1/step]
0: paper exist
1: paper non exist
Responds to paper existence on 2nd carry sensor position.
(0: paper exist, 1: paper non exist)
5-803-006 Fusing Entrance Sensor ENG [0 or 1 / 0 / 1/step]
0: paper exist
1: paper non exist
Responds to paper existence on fusing entrance sensor position.
(0: paper exist, 1: paper non exist)
5-803-007 Fusing Exit Sensor ENG [0 or 1 / 0 / 1/step]
0: paper exist
1: paper non exist
Responds to paper existence on fusing exit sensor position.
(0: paper exist, 1: paper non exist)
5-803-008 Paper Exit Sensor ENG [0 or 1 / 0 / 1/step]
0: paper exist
1: paper non exist
Responds to paper existence on paper exit sensor position.
(0: paper exist, 1: paper non exist)
5-803-009 Inverter Sensor ENG [0 or 1 / 0 / 1/step]
0: paper exist
1: paper non exist
Responds to paper existence on reverse sensor position.
(0: paper exist, 1: paper non exist)
5-803-010 Duplex Exit Sensor ENG [0 or 1 / 0 / 1/step]
0: paper exist
1: paper non exist
Responds to paper existence on duplex exit sensor position.
(0: paper exist, 1: paper non exist)
449
450
3. Engine SP Mode Tables
5-803-011 Duplex Entrance Sensor ENG [0 or 1 / 0 / 1/step]
0: paper exist
1: paper non exist
Responds to paper existence on duplex entrance sensor position.
(0: paper exist, 1: paper non exist)
5-803-012 Tray Full Exit Sensor
This setting is not available for
MP C2004/MP C2504.
ENG [0 or 1 / 0 / 1/step]
0: Not full
1: full
Detects paper full of main unit paper exit tray.
(0: Not full, 1: full)
5-803-013 Tray 1: Paper Height Sensor ENG [0 to 3 / 0 / 1/step]
When full is 100%,
11: 71 to 100%
01: 31 to 70%
00: 11 to 30%
10: 1 to 10%
Detects remaining paper amount of 1st paper feed tray.
(When full is 100%,
11: 71 to 100%, 01: 31 to 70%, 00: 11 to 30%, 10: 1 to 10%)
*Check SP5-803-015 for paper end.
5-803-014 Tray 1: Upper Limit Sensor ENG [0 or 1 / 0 / 1/step]
0: less then limit
1: high then limit
Detects the height of paper loaded in 1st paper feed tray.
(0: less then limit, 1: high then limit)
* As long as you do not press the white bar of the machine side in the tray back, not output.
Input and Output Check
5-803-015 Tray 1: Paper End Detection ENG
Detects paper is running out on 1st paper feed tray.
(0: No paper, 1: paper remaining)
[0 or 1 / 0 / 1/step]
0: No paper
1: paper remaining
5-803-016 Tray 1: Set Sensor ENG [0 or 1 / 0 / 1/step]
0: set
1:not set
Detects that 1st paper feed tray is set to main unit.
(0: set, 1:not set)
5-803-017 Tray 2: Paper Height Sensor ENG [0 to 3 / 0 / 1/step]
When full is 100%,
11: 71 to 100%
01: 31 to 70%
00: 11 to 30%
10: 1 to 10%
Detects remaining paper amount of 2nd paper feed tray.
(When full is 100%,
11: 71 to 100%, 01: 31 to 70%, 00: 11 to 30%, 10: 1 to 10%)
*Check SP5-803-019 for paper end.
5-803-018 Tray 2: Paper End Sensor ENG [0 or 1 / 0 / 1/step]
0: less then limit
1: high then limit
Detects the height of paper loaded in 2nd paper feed tray.
(0: less then limit, 1: high then limit)
* As long as you do not press the white bar of the machine side in the tray back, not output.
451
452
3. Engine SP Mode Tables
5-803-019 Tray 2: Paper End Detection ENG
Detects paper running out of 2nd paper feed tray.
(0: No paper, 1: paper remaining)
[0 or 1 / 0 / 1/step]
0: No paper
1: paper remaining
5-803-020 Tray 2: Set Sensor ENG [0 or 1 / 0 / 1/step]
0: set
1: not set
Detects that 2nd paper feed tray is set to main unit.
(0: set, 1:not set)
5-803-021 Tray 2: Size Sensor ENG [0 to 15 / 0 / 1/step]
Value changes depending on paper size (fence position) set to 2nd paper feed tray.
5-803-022 By-pass: Paper End Sensor ENG [0 or 1 / 0 / 1/step]
0: No paper
1: paper remaining
Detects paper is running out on bypass tray.
(0: No paper, 1: paper remaining)
5-803-023 By-pass: Main Scan Length
Sensor
ENG [0 to 31 / 0 / 1/step]
Value changes depending on main scan direction of paper set to bypass tray.
5-803-024 By-pass: Sub Scan Length
Sensor
ENG [0 or 1 / 0 / 1/step]
Value changes depending on sub scan direction of paper set to bypass tray.
5-803-025 Interlock Release Detection ENG [0 to 1 / 0 / 1/step]
00: Unlocked
11: Locked
Detects open/close of interlock switch (front cover/right cover).
(00: Unlocked, 11: Locked)
Input and Output Check
5-803-026 Right Door Open/Close Sensor ENG [0 or 1 / 0 / 1/step]
0: close
1: open
Detects right door status.
(0: close, 1: open)
5-803-027 Duplex Guide Plate Open/
Close Sensor
ENG [0 or 1 / 0 / 1/step]
0: close
1: open
Detects duplex guide plate status.
(0: close, 1: open)
5-803-028 PTR Open/Close Sensor ENG [0 or 1 / 0 / 1/step]
0: open
1: close
Detects paper transfer unit status.
(0: open, 1: close)
5-803-029 ITB Contact Sensor ENG [0 or 1 / 0 / 1/step]
0: Abutting
1: Alienate
Detects image transfer roller (Y, M, and C) and photoreceptors distance.
(0: Abutting, 1: Alienate)
5-803-030 PTR Contact Sensor ENG [0 or 1 / 0 / 1/step]
0: Abutting
1: Alienate
Detects image transfer belt and paper transfer rollers distance.
(0: Abutting, 1: Alienate)
5-803-031 New ITB Unit Detection
Not available with C1
ENG [0 or 1 / 0 / 1/step]
453
454
3. Engine SP Mode Tables
5-803-032 Toner Collection Full Sensor ENG [0 or 1 / 0 / 1/step]
0: Not full
1: full
Detects full of waste toner bottle.
(0: Not full, 1: full)
5-803-033 Toner Collection Bottle Set
Sensor
ENG [0 or 1 / 0 / 1/step]
0: set
1: not set
Detects that waste toner bottle is set to main unit.
(0: set, 1:not set)
5-803-034 Toner End Sensor:Y ENG [0 or 1 / 0 / 1/step]
0: End
1: Not End
Detects remaining toner amount.
*Power with SP5-804-173 before checking.
(0: End, 1: Not End)
5-803-035 Toner End Sensor:M ENG [0 or 1 / 0 / 1/step]
0: End
1: Not End
Detects remaining toner amount.
*Power with SP5-804-173 before checking.
(0: End, 1: Not End)
5-803-036 Toner End Sensor:C ENG [0 or 1 / 0 / 1/step]
0: End
1: Not End
Detects remaining toner amount.
*Power with SP5-804-173 before checking.
(0: End, 1: Not End)
Input and Output Check
5-803-037 Toner End Sensor:K ENG [0 or 1 / 0 / 1/step]
0: End
1: Not End
Detects remaining toner amount.
*Power with SP5-804-172 before checking.
(0: End, 1: Not End)
5-803-038 Fusing:Area Detection ENG [0 to 15 / 0 / 1/step]
01:200V system
10:100V System
00, 01:unit set error
Detects region of fusing unit.
(0111: 200V system, 1011: 100V System)
5-803-039 Fusing:New Unit Detection ENG [0 or 1 / 0 / 1/step]
0: New
1: Old
Detects New/Old of fusing unit.
(0: New, 1: Old)
5-803-040 Fusing Temp Detect ENG [0 or 1 / 0 / 1/step]
0: Normal
1: High temperature
Detects whether high temperature is detected from fusing unit.
(0: Normal, 1: High temperature)
5-803-041 NC Sensor Temp Detection/ 2 ENG [0 or 1 / 0 / 1/step]
0: Normal
1: High temperature
Detects whether high temperature is detected from fusing unit.
(0: Normal, 1: High temperature)
455
456
3. Engine SP Mode Tables
5-803-042 NC Sensor Temp Detection/ 1 ENG [0 or 1 / 0 / 1/step]
0: Normal
1: High temperature
Detects whether high temperature is detected from fusing unit.
(0: Normal, 1: High temperature)
5-803-047 Nip Pres. Release Home Position
Sensor
ENG [0 or 1 / 0 / 1/step]
0: Pressured
1: Not pressured
Detects state of fusing nip pressure.
(0: Pressured , 1: Not pressured)
5-803-048 Fusing Fan: Lock ENG [0 or 1 / 0 / 1/step]
0: Running
1: Stopped, or locked
Detects locking of fusing exhaust heat fan.
(0: Running, 1: Stopped, or locked)
5-803-049 Dev Fan: Right: Lock ENG [0 or 1 / 0 / 1/step]
0: Running
1: Stopped, or locked
Detects locking of developer air intake fan (right).
(0: Running, 1: Stopped, or locked)
5-803-051 PSU Cooling Fan: Lock ENG [0 or 1 / 0 / 1/step]
0: Running
1: Stopped, or locked
Detects locking of PSU cooling fan.
(0: Running, 1: Stopped, or locked)
5-803-052 Ozone Fan: Lock ENG [0 or 1 / 0 / 1/step]
0: Running
1: Stopped, or locked
Detects locking of ozone exhaust air fan.
(0: Running, 1: Stopped, or locked)
Input and Output Check
5-803-054 PSU Fan: Lock ENG [0 or 1 / 0 / 1/step]
0: Running
1: Stopped, or locked
Detects locking of PSU exhaust heat fan.
(0: Running, 1: Stopped, or locked)
5-803-055 PCB Box Cooling Fan: Lock ENG [0 or 1 / 0 / 1/step]
0: Running
1: Stopped, or locked
Detects locking of electric box cooling fan.
(0: Running, 1: Stopped, or locked)
5-803-058 Paper Exit Cooling Fan: Lock ENG [0 or 1 / 0 / 1/step]
0: Running
1: Stopped, or locked
Detects locking of paper exit cooling fan.
(0: Running, 1: Stopped, or locked)
5-803-060 Toner Supply Cooling Fan: Lock ENG [0 or 1 / 0 / 1/step]
0: Running
1: Stopped, or locked
Detects locking of toner supply cooling fan.
(0: Running, 1: Stopped, or locked)
5-803-063 Development Motor FC: Lock ENG [0 or 1 / 0 / 1/step]
0: Stopped, or locked
1: Running
Detects locking of developer motor (FC).
(0: Running, 1: Stopped, or locked)
5-803-064 Drum Motor FC: Lock ENG [0 or 1 / 0 / 1/step]
0: Stopped, or locked
1: Running
Detects locking of drum motor (FC).
(0: Running, 1: Stopped, or locked)
457
458
3. Engine SP Mode Tables
5-803-065 Fusing Motor: Lock ENG [0 or 1 / 0 / 1/step]
0: Stopped, or locked
1: Running
Detects locking of fusing motor.
(0: Running, 1: Stopped, or locked)
5-803-066 Transfer Drum Motor K: Lock ENG [0 or 1 / 0 / 1/step]
0: Stopped, or locked
1: Running
Detects locking of transfer drum motor K.
(0: Running, 1: Stopped, or locked)
5-803-068 PP:CB:SC Detection ENG [0 or 1 / 0 / 1/step]
0: SC detected
1: Normal
Detects SC of HVP (electrify/develop).
(0: SC detected, 1: Normal)
5-803-069 PP:TTS:SC Detection ENG [0 or 1 / 0 / 1/step]
0: SC detected
1: Normal
Detects SC of HVP (transfer).
(0: SC detected, 1: Normal)
5-803-072 Key Counter: Set 1 ENG
Detects setting of key counter.
(0: set, 1:unset)
(key counter: set 1=0, 2=1 for set, others for unset)
[0 or 1 / 0 / 1/step]
0: set
1:unset
Input and Output Check
5-803-073 Key Counter: Set 2 ENG [0 or 1 / 0 / 1/step]
0: unset
1:set
Detects setting of key counter.
(0: unset, 1:set)
(key counter: set 1=0, 2=1 for set, others for unset)
5-803-074 Key Card Set ENG [0 or 1 / 0 / 1/step]
0: set
1: not set
Detects that key card is set to main unit.
(0: set, 1:not set)
5-803-075 1 Bin Tray: Paper Sensor ENG [0 or 1 / 0 / 1/step]
0: paper exist
1: paper non exist
Detects that paper is left upon the tray.
(0: paper exist, 1: paper non exist)
5-803-076 1 Bin Tray: Set Detection System ENG [0 or 1 / 0 / 1/step]
0: paper exist
1: paper non exist
Detects that tray is set to main unit.
(0: set, 1:not set)
5-803-077 Bridge Relay Sensor ENG [0 or 1 / 0 / 1/step]
0: paper exist
1: paper non exist
Responds to paper existence on carry sensor position or bridge unit.
(0: paper exist, 1: paper non exist)
459
460
3. Engine SP Mode Tables
5-803-078 Bridge Exit Sensor ENG [0 or 1 / 0 / 1/step]
0: Paper exist
1: Paper do not exist
Responds to paper existence on paper exit sensor position or bridge unit.
(0: paper exist, 1: paper non exist)
5-803-079 Bridge Set Detection System ENG [0 or 1 / 0 / 1/step]
10: set
11:not set
Detects that bridge unit is set to main unit.
(10: set, 11:not set)
5-803-082 Bridge Relay/Left Exit Cover
Sensor
ENG [0 or 1 / 0 / 1/step]
0: close
1: open
Detects open/close of the left carry cover open/close sensor (left paper exit tray) and the relay carry cover open/close sensor (bridge unit).
(0: close, 1: open)
5-803-083 Bridge Exit/Upper Exit Cover
Sensor
ENG [0 or 1 / 0 / 1/step]
0: close
1: open
Detects open/close of the upper carry cover open/close sensor (left paper exit tray) and the relay paper exit cover open/close sensor (bridge unit).
(0: close, 1: open)
5-803-084 Shift Tray: Set Detection System ENG [0 or 1 / 0 / 1/step]
01: set
11:not set
Detects that shift tray is set to main unit.
(01: set, 11:not set)
Input and Output Check
5-803-085 Shift Tray: Position Sensor 1 ENG [0 or 1 / 0 / 1/step]
0: Stop on this side. during moving towards inner
1: Stop on inner side. during moving towards this side
Detects shift tray position.
(0: Stop on this side. during moving towards inner,
1: Stop on inner side. during moving towards this side)
5-803-086 Shift Tray: Position Sensor 2 ENG [0 or 1 / 0 / 1/step]
*It is a backup sensor with this machine, so "1" is always displayed)
5-803-094 GAVD Open/Close Detection ENG [0 or 1 / 0 / 1/step]
For checking door open/close during process. No need to operate.
5-803-095 Bridge 24V Fuse Detection ENG [0 or 1 / 0 / 1/step]
0: Not cut
1: Cut
Detects state of 24V fuse on the bridge unit.
(0: Not cut, 1: Cut)
5-803-096 Bridge 5V Fuse Detection ENG [0 or 1 / 0 / 1/step]
0: Not cut
1: Cut
Detects state of 5V fuse on the bridge unit.
(0: Not cut, 1: Cut)
5-803-200 HP Sensor ENG
Tests the scanner HP sensor.
5-803-201 Platen Cover Sensor ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
5803
Tests the book open/close sensor.
[INPUT Check]
Gets information of specified sensor.
461
462
3. Engine SP Mode Tables
5-803-211 Bank: Tray3: Feed Sensor
5-803-212 Bank: Tray4: Feed Sensor
5-803-213 Bank: Tray5: Feed Sensor
5-803-214 Bank: Tray3: Transport Sensor
5-803-215 Bank: Tray4: Transport Sensor
5-803-216 Bank: Tray5: Transport Sensor
5-803-217 Bank: Feed Cover Open
Detection 1
5-803-218 Bank: Feed Cover Open
Detection 2
5-803-219 LCT Paper Supply Open/Close
5-803-220 LCT Slide Open/Close
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
0: paper not detected
1: paper detected.
ENG
[0 or 1 / 0 / 1/step]
0: cover open
1: cover closed
ENG
ENG [0 or 1 / 0 / 1/step]
0: slide open
1: slide closed
6007 [ADF INPUT Check]
Gets sensor information from ADF. Displays signal level of sensor as it is.
6-007-001 Original Length 1 (B5 Detection
Sensor)
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step] 6-007-002 Original Length 2 (A4 Detection
Sensor)
6-007-003 Original Length 3 (LG Detection
Sensor)
6-007-004 Original Width 1
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
6-007-005 Original Width 2
6-007-006 Original Width 3
6-007-007 Original Width 4
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
Input and Output Check
6-007-008 Original Width 5
6-007-009 Original Detection
6-007-011 Skew Correction
6-007-013 Registration Sensor
6-007-014 Exit Sensor
6-007-015 Feed Cover Sensor
6-007-016 Lift Up Sensor
6-007-023 Rear Edge Detection
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
6011 [1-Pass ADF INPUT Check]
For Single-Pass simultaneous duplex models only.
6-011-001 Original Length 1 (B5 Sensor) ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
6-011-002 Original Length 2 (A4 Sensor) ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
6-011-003 Original Length 3 (LG Sensor) ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
6-011-004 Original Width 1 ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
6-011-005 Original Width 2 ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
6-011-006 Original Width 3 ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
6-011-007 Original Width 4 ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
463
464
3. Engine SP Mode Tables
6-011-008 Original Width 5 ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
6-011-009 Original Detection ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when original is set.
6-011-010 Separation Sensor ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
6-011-011 Skew Correction ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
6-011-012 Scan Entrance Sensor ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
6-011-013 Registration Sensor ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
6-011-014 Exit Sensor ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
6-011-015 Feed Cover Sensor ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when cover is open.
6-011-016 Lift Up Sensor ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when lift up.
6-011-018 Pick-Up Roller HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when pick up roller is not in home position.
6-011-021 Bottom Plate HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when bottom plate is not in home position.
6-011-022 Bottom Plate Position Sensor ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when pick up roller is not in the correct position.
Input and Output Check
6-011-023 Original Length 4 (LT/A4 Tail
Sensor)
ENG [0 or 1 / 0 / 1/step]
Gets sensor information from ADF. Gives 1 when there is a paper at sensor area.
6123 [INPUT Check: 2K/3K FIN]
6-123-001 Entrance Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-002 Horizontal Transport Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-003 Switchback Transport Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-004 Proof Tray Exit Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-005 Shift Tray Exit Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-006 Booklet Stapler Exit Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-007 Paper Exit Open/Close Guide
HP Sensor
ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-008 Punch HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-009 Punch Move HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
465
466
3. Engine SP Mode Tables
6-123-010 S-to-S Registration Detection HP
Sensor
ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-011 Lower Junction Solenoid HP
Sensor
ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-012 Jogger HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-013 Positioning Roller HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-014 Feed-out HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-015 Stapler Moving HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-016 Booklet Stapler HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-017 Booklet Jogger HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-018 Booklet Jog Solenoid HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-019 Booklet Standard Fence HP
Sensor
ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-020 Booklet Stapler HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-022 Folder Blade Cam HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
Input and Output Check
6-123-023 Folder Blade HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-024 Shift Roller HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-028 Drag Roller Vibrating HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-029 LE Guide HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-030 TE Stack Plate HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-031 Staple Tray Paper Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-032 ITB Paper Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-033 Booklet Stapler Transport Paper
Sn: Upper
ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-034 Booklet Stapler Transport Paper
Sn: Lower
ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-035 Paper Height Sensor: Shift ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-036 Corner Stapler Paper Height
Sensor 1
ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
467
468
3. Engine SP Mode Tables
6-123-037 Corner Stapler Paper Height
Sensor 2
ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-038 Proof Tray Full Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-039 Booklet Stapler Full Sensor 1 ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-040 Booklet Stapler Full Sensor 2 ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-041 S-to-S Registration Detection
Sensor
ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-042 Punch RPS Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-043 Corner Stapler Leading Edge
Detection Sensor
ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-044 Corner Stapler Staple End
Sensor
ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-045 Booklet Stapler Staple End
Sensor: Front
ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-046 Booklet Stapler Staple End
Sensor: Rear
ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-047 Shift Tray Lower Limit Sensor 1 ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
Input and Output Check
6-123-048 Shift Tray Lower Limit Sensor 2 ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-049 Shift Tray Lower Limit Sensor 3 ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-050 Shift Tray Lower Limit Sensor 4 ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-051 Shift Tray Lower Limit Sensor 5 ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-052 Punch Chad Full Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-123-053 Punch Set Detection ENG [0 or 1 / 0 / 1/step]
0: connected
1: not connected
Gets connection status of punch unit.
6-123-054 Shift Jogger Set Detection ENG [0 or 1 / 0 / 1/step]
0: connected
1: not connected
Gets connection status of setting jogger unit.
* Not use: currently, VOLGA-B does not have setting jogger in system configuration.
6-123-055 Booklet Stapler Set Detection ENG [0 or 1 / 0 / 1/step]
0: not connected
1: connected
Gets connection status of saddle stitch unit.
6-123-056 Front Door SW ENG [0 or 1 / 0 / 1/step]
Gets information of specified switch. Displays signal level of switch as it is.
6-123-057 Dynamic Roller Open/Close
Guide Plate Sensor
ENG [0 or 1 / 0 / 1/step]
Gets information of specified switch. Displays signal level of switch as it is.
469
470
3. Engine SP Mode Tables
6-123-058 Tray Upper Limit SW ENG [0 or 1 / 0 / 1/step]
Gets information of specified switch. Displays signal level of switch as it is.
6-123-059 Paper Exit Open/Close Guide
Plate Limit SW
ENG [0 or 1 / 0 / 1/step]
Gets information of specified switch. Displays signal level of switch as it is.
6-123-060 Punch Selection DIPSW 1 ENG [0 or 1 / 0 / 1/step]
Gets information of specified switch. Displays signal level of switch as it is.
6-123-061 Punch Selection DIPSW 2 ENG [0 or 1 / 0 / 1/step]
Gets information of specified switch. Displays signal level of switch as it is.
6-123-065 Paper Guide HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets information of specified switch. Displays signal level of switch as it is.
6-123-066 Shift Jogger HP Sensor: Front ENG [0 or 1 / 0 / 1/step]
Gets information of specified switch. Displays signal level of switch as it is.
6-123-067 Shift Jogger HP Sensor: Rear ENG [0 or 1 / 0 / 1/step]
Gets information of specified switch. Displays signal level of switch as it is.
6-123-068 Shift Jogger Retraction HP
Sensor: Upper
ENG [0 or 1 / 0 / 1/step]
Gets information of specified switch. Displays signal level of switch as it is.
6-123-069 Shift Jogger Retraction HP
Sensor: Lower
ENG [0 or 1 / 0 / 1/step]
Gets information of specified switch. Displays signal level of switch as it is.
6135 [INPUT Check: FrontFIN]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-135-001 Entrance Sensor
6-135-002 Carry Sensor
6-135-003 Exit Sensor
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
Input and Output Check
6-135-004 Staple Tray Paper Sensor
6-135-005 Front Jogger HP Sensor
6-135-006 Rear Jogger HP Sensor
6-135-007 Sft Roller HP Sensor
6-135-008 Hitroll HP Sensor
6-135-009 Ext Guide Plate HP Sensor
6-135-010 Staple Moving HP Sensor
6-135-011 Shift Tray Paper Sensor
6-135-012 Shift Tray Limit Sensor
6-135-013 Staple Rotation Sensor
6-135-014 Staple Near End Sensor
6-135-015 Self Priming Sensor
6-135-016 Stopper HP Sensor
6-135-017 Punch HP Sensor
6-135-018 Punch Pluse Count Sensor
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
*ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
6-135-019 Punch Chad Full Sensor
6-135-020 Punch Moving HP Sensor
6-135-021 Punch Registration Detection HP
Sensor
6-135-022 Punch Registration Detection
Sensor
6135 [INPUT Check: FrontFIN]
ENG
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
Gets information of specified switch. Displays signal level of switch as it is.
6-135-023 Slide Door SW ENG [0 or 1 / 0 / 1/step]
6-135-024 Shift Tray Upper Limit SW ENG [0 or 1 / 0 / 1/step]
471
472
3. Engine SP Mode Tables
6161 [FIN (1K FIN) INPUT Check]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-161-001 Entrance Sensor ENG [0 or 1 / 0 / 1/step]
6-161-002 Upper Cover Open/Close
Sensor
ENG [0 or 1 / 0 / 1/step]
6-161-003 Proof Tray Exit Sensor
6-161-004 Proof Tray Full Sensor
6-161-005 Shift HP Sensor
6-161-006 Exit Guide Plate Open/Close HP
Sensor
6-161-007 Shift Paper Exit (Lift Tray Exit)
Sensor
6-161-008 Positioning Roller HP Sensor
ENG
ENG
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
6-161-009 Lift Tray Paper Sensor
6-161-010 Jogger HP Sensor
6-161-011 Feed Out HP Sensor
6-161-012 Lift Tray Lower Limit Sensor
(Upper)
6-161-013 Lift Tray Lower Limit Sensor
(Lower)
6-161-014 Staple Tray Paper Sensor
ENG
ENG
ENG
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
6-161-015 Stapler Moving HP Sensor
6-161-016 Near End Sensor (Common:
Corner/Bklt Stplr)
6-161-017 Self Priming Sensor
(Common:Crnr/Bklt Stplr)
6-161-018 Driver HP Sensor (Corner/
Booklet Stapler)
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
Input and Output Check
6-161-020 Clincher HP Sensor (Corner/
Booklet Stapler)
6-161-022 Stapler Retraction Sensor
6-161-023 Untitled
6-161-024 Untitled
6-161-025 Untitled
6-161-026 Punch HP Sensor
6-161-027 Punch RP Sensor
6-161-028 Punch Hopper Full Sensor
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
6-161-029 Punch Move HP Sensor
6-161-030 S-to-S Registration Detection HP
Sensor
6-161-031 S-to-S Registration Detection
Sensor
6161 [FIN (1K FIN) INPUT Check]
ENG [0 or 1 / 0 / 1/step]
Gets information of specified switch. Displays signal level of switch as it is.
6-161-032 Punch Selection DIPSW 1 ENG [0 or 1 / 0 / 1/step]
6-161-033 Punch Selection DIPSW 2
6161 [FIN (1K FIN) INPUT Check]
ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-161-034 ITB Transport Sensor: Right
6-161-035 ITB Transport Sensor: Left
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
6-161-036 Stack Transport Sensor
6-161-037 Stack Trans Upper Pressure
Release HP Sensor
6-161-038 Stack Trans Lower Pressure
Release HP Sensor
6-161-039 Fold Blade HP Sensor
ENG
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
473
474
3. Engine SP Mode Tables
6-161-040 Fold Cam HP Sensor
6-161-041 TE Stopper Transport Sensor
6-161-042 TE Stopper HP Sensor
6-161-043 Booklet Folder Exit Sensor
6-161-044 Booklet Folder Tray Full Sensor:
Upper
6-161-045 Booklet Folder Tray Full Sensor:
Lower
6161 [FIN (1K FIN) INPUT Check]
ENG
ENG
ENG
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
Gets information of specified switch. Displays signal level of switch as it is.
6-161-046 Door Open/Close SW ENG [0 or 1 / 0 / 1/step]
6-161-047 Lift Tray Upper Limit SW
6161 [FIN (1K FIN) INPUT Check]
ENG [0 or 1 / 0 / 1/step]
Gets information of specified sensor. Displays signal level of sensor as it is.
6-161-048 Paper Guide HP Sensor ENG [0 or 1 / 0 / 1/step]
6184 [Input Check: NoStplBindFIN]
6-184-001 Entrance Sensor ENG [0 or 1 / 0 / 1/step]
Gets the entrance sensor information of non staple finisher.
(0: Sensor Off, 1: Sensor On)
6-184-002 Exit Sensor ENG [0 or 1 / 0 / 1/step]
Gets the paper exit sensor information of non staple finisher.
(0: Sensor Off, 1: Sensor On)
6-184-003 Horizontal Registration Detection
Sensor
ENG [0 or 1 / 0 / 1/step]
Gets the horizontal registration sensor information of non staple finisher.
(0: Sensor Off, 1: Sensor On)
Input and Output Check
6-184-004 Shift HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets the shift HP sensor information of non staple finisher.
(0: Sensor Off, 1: Sensor On)
6-184-005 Junction Solenoid HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets the junction solenoid HP sensor information of non staple finisher.
(0: Sensor Off, 1: Sensor On, “0“ appears if sensor detects home position)
6-184-006 Exit Pressure Release HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets the exit pressure release HP sensor information of non staple finisher.
(0: Sensor Off, 1: Sensor On)
6-184-007 Stapler HP Sensor ENG [0 or 1 / 0 / 1/step]
Gets the stapler HP sensor information of non staple finisher.
(0: Sensor On, “0“ appears if sensor detects home position)
6-184-008 Tray Full Detection Sensor 1 ENG [0 or 1 / 0 / 1/step]
Gets the tray full detection sensor 1 information of non staple finisher. (0: Paper overflow )
6-184-009 Tray Full Detection Sensor 2
6-184-010 Slide Door Open/Close Door
SW
ENG [0 or 1 / 0 / 1/step]
Gets the tray full detection sensor 2 information of non staple finisher. (0: Paper overflow )
ENG [0 or 1 / 0 / 1/step]
Gets the slide door switch information of non staple finisher.
(0: Close, 1: Open)
5804 [OUTPUT Check]
475
476
3. Engine SP Mode Tables
5-804-001 Feed Pickup Solenoid 1
This setting is not available for
MP C2004/MP C2504.
ENG [0 or 1 / 0 / 1/step]
Moves 1st paper feed tray pick up solenoid.
5-804-002 Feed Pickup Solenoid 2
This setting is not available for
MP C2004/MP C2504.
ENG [0 or 1 / 0 / 1/step]
Moves 2nd paper feed tray pick up solenoid.
5-804-003 Bypass Pickup Solenoid ENG [0 or 1 / 0 / 1/step]
Moves bypass pick up solenoid.
5-804-004 Exit Junction Solenoid
Moves output paper divide solenoid.
ENG [0 or 1 / 0 / 1/step]
5804 [OUTPUT Check]
Moves paper feed tray rising motor.
* Do not execute SP 5-804-006/008 without removing the paper tray. Otherwise, the tray might be damaged.
5-804-005 Tray 1 Lift Motor:CW ENG [0 or 1 / 0 / 1/step]
5-804-006 Tray 1 Lift Motor:CCW
5-804-007 Tray 2 Lift Motor:CW
5-804-008 Tray 2 Lift Motor:CCW
5804 [OUTPUT Check]
ENG
ENG
ENG
Moves register motor.
5-804-009 Regist Motor:CCW:Standard
Speed
5-804-011 Regist Motor:CCW:Low Speed
5804 [OUTPUT Check]
ENG
ENG
[0 or 1 / 0 / 1/step]
Input and Output Check
5-804-015 Regist Motor:Position Hold
5804
Holds position of register motor.
[OUTPUT Check]
ENG [0 or 1 / 0 / 1/step]
Moves paper feed motor.
* It is fed if there is paper in the paper tray.
ENG [0 or 1 / 0 / 1/step] 5-804-016 Feed Motor:CW:Standard
Speed
5-804-018 Feed Motor:CW:Low Speed
5-804-022 Feed Motor:CCW:Standard
Speed
ENG
ENG
ENG 5-804-024 Feed Motor:CCW:Low Speed
5804 [OUTPUT Check]
Moves transport motor.
5-804-028 Bypass V-Transport
Motor:CW:Std Speed
5-804-030 Bypass V-Transport
Motor:CW:Low Speed
5804 [OUTPUT Check]
ENG
ENG
[0 or 1 / 0 / 1/step]
5-804-034 Bypass V-Transport
Motor:Position Hold
Holds position of transport motor.
ENG [0 or 1 / 0 / 1/step]
5-804-037 Exit Motor: CW: Fusing
Pressure Release
ENG [0 or 1 / 0 / 1/step]
Moves fusing dis-pressure.
* If driving this motor while attaching the fusing unit, be sure to stop it less than 5 seconds. Otherwise, the unit might be damaged.
5804 [OUTPUT Check]
Moves paper exit motor.
477
478
3. Engine SP Mode Tables
5-804-041 Exit Motor:CCW:Standard
Speed
5-804-043 Exit Motor:CCW:Low Speed
5804 [OUTPUT Check]
Moves reverse motor.
5-804-047 Inverter Motor:CW:Standard
Speed
5-804-049 Inverter Motor:CW:Low Speed
5-804-052 Inverter Mt: CW: Normal
Speed: Duplex
5-804-054 Inverter Mt: CW: Low Speed:
Duplex
5-804-056 Inverter Motor:CCW:Standard
Speed
5-804-058 Inverter Motor:CCW:Low
Speed
5-804-061 Inverter Mt: CCW: Normal
Speed: Inc Speed
5804 [OUTPUT Check]
Moves duplex entrance motor.
5-804-065 Duplex Entrance
Motor:CW:Standard Speed
5-804-067 Duplex Entrance
Motor:CW:Low Speed
5-804-068 Duplex Entrance Motor:
Normal Speed: Duplex
5-804-069 Duplex Entrance Motor: Low
Speed: Duplex
5804 [OUTPUT Check]
Moves bypass/duplex motor.
ENG [0 or 1 / 0 / 1/step]
ENG
ENG [0 or 1 / 0 / 1/step]
ENG
ENG
ENG
ENG
ENG
ENG
ENG [0 or 1 / 0 / 1/step]
ENG
ENG
ENG
5-804-071 Duplex Bypass
Motor:CW:Standard Speed
5-804-073 Duplex Bypass Motor:CW:Low
Speed
5-804-074 Duplex Bypass Motor: CW:
Normal Speed: Dup
5-804-075 Duplex Bypass Motor: CW:
Low Speed: Duplex
ENG
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
5-804-077 Duplex Bypass
Motor:CCW:Standard Speed
5-804-079 Duplex Bypass
Motor:CCW:Low Speed
5804 [OUTPUT Check]
ENG
ENG
5-804-083 Duplex Bypass Motor:Position
Hold
5804
ENG
Holds position of bypass/duplex motor.
[OUTPUT Check]
[0 or 1 / 0 / 1/step]
Moves fusing motor. *See Important below
5-804-092 Fusing Motor:CW:Standard
Speed
ENG [0 or 1 / 0 / 1/step]
5-804-094 Fusing Motor:CW:Low Speed ENG
5-804-098 Fusing Motor:CCW:Low Speed ENG
Input and Output Check
479
480
3. Engine SP Mode Tables
Important: Use the procedure below to do the output checks for the fusing exit motor. If you do not follow this procedure, a kink will form in the fusing belt sleeve, and the fusing sleeve belt unit will need to be replaced.
1. Do one of the following:
• Open the right cover of the paper bank
• Remove one of the toner bottles
• Pull out the waste toner bottle half-way
• Remove the fusing unit
2. Enter SP mode.
3. Do the following out output checks:
• SP5-804-092 (Fusing Motor:CW:Standard Speed)
• SP5-804-094 (Fusing Motor:CW:Low Speed)
• SP5-804-098 (Fusing Motor:CCW:Low Speed)
4. Without exiting SP mode, turn the main power switch off and then on again.
Important: If you exit SP mode before you turn the main power switch off, the fusing exit motor will stay off when the machine warms up. Heat will be concentrated in one area of the fusing belt sleeve and cause a kink to form. If this happens, you will need to replace the fusing sleeve belt unit.
5. Do the reverse of what you did in step 1 (for example, reattach the fusing unit).
5804 [OUTPUT Check]
ENG [0 or 1 / 0 / 1/step] 5-804-104 Polygon Motor: L
Runs motor with 21969 rpm.
5-804-105 Polygon Motor: M
Runs motor with 25512 rpm.
5-804-106 Polygon Motor: H
Runs motor with 30236 rpm.
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
5-804-107 Polygon Motor: HH
Runs motor with 34488 rpm.
5-804-110 Fusing Fan: Full Speed
Moves fusing exhaust fan.
ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step]
Input and Output Check
5-804-111 Fusing Fan: Half Speed ENG [0 or 1 / 0 / 1/step]
Moves fusing exhaust fan.
5-804-113 PSU Cooling/Exhaust Heat Fan ENG [0 or 1 / 0 / 1/step]
Moves PSU cooling fan and PSU exhaust fan (not included in this machine).
5-804-114 Ozone Fan ENG [0 or 1 / 0 / 1/step]
Moves ozone exhaust heat fan.
5-804-115 PCB Box Cooling Fan/ Exhaust
Cooling Fan
ENG [0 or 1 / 0 / 1/step]
Moves controller box cooling fan and exhaust cooling fan.
ENG [0 or 1 / 0 / 1/step] 5-804-116 Development: Right: Half
Speed
Moves development intake fan.
5-804-117 Drive Cooling/ Main/ Toner
Supply Cooling Fan
ENG [0 or 1 / 0 / 1/step]
Moves drive cooling fan (not included in this machine), main exhaust fan (not included in this machine), and toner supply cooling fan.
5-804-118 Development: Right ENG [0 or 1 / 0 / 1/step]
Moves development intake fan.
5-804-119 Development Solenoid
5804
Moves development solenoid.
[OUTPUT Check]
Moves development motor.
5-804-128 Development Motor FC:
Standard Speed
5-804-130 Development Motor FC: Low
Speed
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
481
482
3. Engine SP Mode Tables
5804 [OUTPUT Check]
Moves/Stops PCU motor :CMY.
* Execute this SP after correcting the cam position so that ITB contact/separation lever of the color station is released.
5-804-132 Drum Motor FC: Standard
Speed
ENG [0 or 1 / 0 / 1/step]
5-804-134 Drum Motor FC: Low Speed
5804 [OUTPUT Check]
ENG
Moves/Stops PCU motor: Black/ ITB drive motor.
* Execute this SP after correcting the cam position so that ITB contact/separation lever of the color station is released.
5-804-136 Transfer Drum Motor K:
Standard Speed
5-804-138 Transfer Drum Motor K: Low
Speed
5804 [OUTPUT Check]
ENG
ENG
[0 or 1 / 0 / 1/step]
Moves paper transfer contact and release motor.
5-804-140 PTR Contact Motor:CW
5-804-141 PTR Contact Motor:CCW
ENG [0 or 1 / 0 / 1/step]
ENG
5804 [OUTPUT Check]
Moves ITB contact and release motor (reverse to toner supply motor M).
* Execute this SP after correcting the cam position so that ITB contact/separation lever of the color station is released.
ENG [0 or 1 / 0 / 1/step] 5-804-150 Toner Supply Motor M:CW:
(ITB Contact)
5804 [OUTPUT Check]
Moves relay carry motor (bridge unit)/left paper exit carry motor (left paper exit tray).
Input and Output Check
5-804-163 Bridge Relay/Left Exit Motor:
Normal Speed
5-804-165 Bridge Relay/Left Exit Motor:
Low Speed
5-804-166 Bridge Relay/Left Ex Mt:
Normal Speed Upper
5804 [OUTPUT Check]
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
5-804-169 Bridge Junction/Left Exit
Junction Solenoid
5-804-170 Shift Tray Motor:CW
Moves shift tray motor.
ENG [0 or 1 / 0 / 1/step]
Moves relay divide solenoid (bridge unit)/left paper exit divide solenoid (left paper exit tray).
ENG [0 or 1 / 0 / 1/step]
5-804-171 Shift Tray Motor:CCW
Moves shift tray motor.
ENG [0 or 1 / 0 / 1/step]
5-804-172 Toner End Sensor: K Power ENG [0 or 1 / 0 / 1/step]
Supples power to toner end sensor (K).
5-804-173 Toner End Sensor: FC Power ENG [0 or 1 / 0 / 1/step]
Supples power to toner end sensor (FC).
5-804-174 Drum PCL: K ENG [0 or 1 / 0 / 1/step]
Lights (PWM drive) the drum PCL (K).
* Continuing the OPC's exposure, it might accumulate damage due to electrostatic locally.
• If operating QL without rotation, be sure to stop it within 10 seconds.
• Do rotate the OPC drum when QL is turned on.
483
484
3. Engine SP Mode Tables
5-804-175 Drum PCL: FC
5804
ENG [0 or 1 / 0 / 1/step]
Lights (PWM drive) the drum PCL (FC).
* Continuing the OPC's exposure, it might accumulate damage due to electrostatic locally.
• If operating QL without rotation, be sure to stop it within 10 seconds.
• Do rotate the OPC drum when QL is turned on.
[OUTPUT Check]
Outputs PWM for electrify HVP (DC/AC:Y/M/C/K).
5-804-176 PP: Charge DC: Y ENG [0 or 1 / 0 / 1/step]
5-804-177 PP: Charge DC: M
5-804-178 PP: Charge DC: C
ENG
ENG
5-804-179 PP: Charge DC: K
5-804-180 PP: Charge AC: Y
5-804-181 PP: Charge AC: M
5-804-182 PP: Charge AC: C
ENG
ENG
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
This setting is not available for MP
C2004/MP C2504
5-804-183 PP: Charge AC: K
5804 [OUTPUT Check]
Outputs PWM for develop HVP.
5-804-184 PP: Development: Y
5-804-185 PP: Development: M
5-804-186 PP: Development: C
5-804-187 PP: Development: K
5804 [OUTPUT Check]
ENG [0 or 1 / 0 / 1/step]
ENG
ENG
ENG
Outputs PWM for transfer HVP (image transfer: Y/M/C/K).
Input and Output Check
5-804-195 PP: ITB: Y
5-804-196 PP: ITB: M
5-804-197 PP: ITB: C
5-804-198 PP: ITB: K
5804 [OUTPUT Check]
ENG
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
Outputs PWM for transfer HVP (paper transfer: +/-).
5-804-199 PP: PTR: + ENG [0 or 1 / 0 / 1/step]
5-804-200 PP: PTR: -
5804 [OUTPUT Check]
ENG
5-804-202 Scanner Lamp ENG [0 or 1 / 0 / 1/step]
Checks output of scanner lamp.
Use to check light source malfunction when SC101-01, SC101-02, SC102-00,
SC142-00 occurs.
5-804-206 PTR Open/Close LED ENG [0 or 1 / 0 / 1/step]
Lights paper transfer open/close LED.
5-804-208 TM/P Sensor: F ENG [0 or 1 / 0 / 1/step]
Lights TM/P sensor: Front glowing part.
5-804-209 TM/P Sensor: C ENG [0 or 1 / 0 / 1/step]
Lights TM/P sensor: Center glowing part.
5-804-210 TM/P Sensor: R ENG [0 or 1 / 0 / 1/step]
Lights TM/P sensor: Rear glowing part.
5-804-211 Toner Sensor Power ENG [0 or 1 / 0 / 1/step]
ENG [0 or 1 / 0 / 1/step] 5-804-232 Toner IDTAG Power
5804 [OUTPUT Check]
5-804-239 Fusing Exit Drive Solenoid ENG [0 or 1 / 0 / 1/step]
485
486
3. Engine SP Mode Tables
5804 [OUTPUT Check]
Continuously drives specified motor for operation test.
5-804-241 Bank: Tray3: Feed Mt:
Standard Speed
ENG [0 or 1 / 0 / 1/step]
ENG 5-804-242 Bank: Tray4: Feed Mt:
Standard Speed
5-804-243 Bank: Tray5: Feed Mt:
Standard Speed
ENG
ENG 5-804-244 Bank: Tray3: Transport Mt:
Standard Speed
5-804-245 Bank: Tray4: Transport Mt:
Standard Speed
5-804-246 Bank: Tray5: Transport Mt:
Standard Speed
5804 [OUTPUT Check]
ENG
ENG
Drives specified motor for a certain period of time to test operation.
5-804-247 Bank: Tray3: PU Solenoid ENG [0 or 1 / 0 / 1/step]
5-804-248 Bank: Tray4: PU Solenoid
5-804-249 Bank: Tray5: PU Solenoid
ENG
ENG
6008 [ADF OUTPUT Check]
Checks operation of the load of ADF.
6-008-003 Feed Motor Forward
Rotates paper feed motor forward.
ENG
6-008-004 Feed Motor Reverse ENG
Rotates paper feed motor backward.
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
6-008-005 Relay Motor Forward
Rotates carry motor forward.
6-008-006 Relay Motor Reverse
Rotates carry motor backward.
6-008-011 Inverter Solenoid
Interval drives reverse solenoid.
6-008-012 Stamp
ENG
ENG
ENG
ENG
Interval drives DONE stamp.
6-008-013 Fan Motor
Interval drives FAN motor.
6-008-014 Feed Clutch
ENG
ENG
Interval drives paper feed clutch.
6-008-015 Feed Solenoid ENG
Interval drives paper feed solenoid.
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
6012 [1-Pass ADF OUTPUT Check]
For Single-Pass simultaneous duplex models only.
6-012-001 Pick-Up Motor Forward ENG [0 or 1 / 0 / 1/step]
0:Off
1:On
Forwardly rotates ADF pick up motor.
6-012-003 Feed Motor Forward ENG [0 or 1 / 0 / 1/step]
0:Off
1:On
Forwardly rotates ADF paper feed motor.
Input and Output Check
487
488
3. Engine SP Mode Tables
6-012-005 Relay Motor Forward ENG [0 or 1 / 0 / 1/step]
0:Off
1:On
Forwardly rotates ADF paper carry motor.
6-012-009 Exit Motor Forward ENG [0 or 1 / 0 / 1/step]
0:Off
1:On
Forwardly rotates ADF paper exit motor.
6-012-010 Bottom Plate Motor For/Rev ENG [0 or 1 / 0 / 1/step]
0:Off
1:On
Moves up/down the bottom plate by driving the ADF bottom plate motor forward, backward.
6-012-012 Stamp ENG [0 or 1 / 0 / 1/step]
0:Off
1:On
Stamps the DONE stamp.
6-012-015 Pull-Out Motor Forward ENG [0 or 1 / 0 / 1/step]
0:Off
1:On
Forwardly rotates ADF pull out motor.
6-012-016 Middle Motor Forward ENG [0 or 1 / 0 / 1/step]
0:Off
1:On
Forwardly rotates ADF middle motor.
6124 [OUTPUT Check: 2K/3K FIN]
6-124-001 Entrance Transport Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-002 Horizontal Transport Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-003 Pre-Stack Transport Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-004 ITB Transport Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-005 Paper Exit Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-006 Upper Junction Solenoid ENG [0 or 1 / 0 / 1/step]
Turns NO/OFF specified solenoid for validation.
6-124-007 TE Stack Plate Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-008 Paper Exit Open/Close
Guide Plate Motor
ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-009 Punching Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-010 Punch Move Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-011 S-to-S Registration
Detection Move Motor
ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-012 Lower Junction Solenoid
Motor
ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
Input and Output Check
489
490
3. Engine SP Mode Tables
6-124-013 Jogger Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-014 Positioning Roller Rotation
Motor
ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-015 Feed-out Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-016 Booklet Stapler Move
Motor
ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-017 Corner Stapler Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-018 Booklet Stapler Jogger
Motor
ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-019 Booklet Stapler Jog
Solenoid Move Motor
ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-020 Booklet Stapler Standard
Fence Motor
ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-021 Booklet Stapler Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-022 Dynamic Roller Transport
Motor
ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-023 Folder Transport Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
Input and Output Check
6-124-025 Press-fold Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-026 Tray Lift Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-027 Shift Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-028 Front Shift Jogger Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
* Not use: currently, VOLGA-B does not have setting jogger in system configuration.
6-124-029 Rear Shift Jogger Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
* Not use: currently, VOLGA-B does not have setting jogger in system configuration.
6-124-030 Shift Jogger Retraction
Motor
ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
* Not use: currently, VOLGA-B does not have setting jogger in system configuration.
6-124-031 Drag Roller Vibrating Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-032 LE Guide Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-033 Navigation LED (All) ENG [0 or 1 / 0 / 1/step]
Lights all guide LED.
6-124-037 Positioning Roller Transport
Motor
ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
6-124-038 Paper Guide Motor ENG [0 or 1 / 0 / 1/step]
Drives specified motor for a certain period of time to test operation.
491
492
3. Engine SP Mode Tables
6136 [OUTPUT Check: FrontFIN]
Continuously drives specified motor for operation test.
6-136-001 Entrance Motor *ENG [0 or 1 / 0 / 1/step]
6-136-002 Carry Motor
6-136-003 Exit Motor
6136
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[OUTPUT Check: FrontFIN]
Drives specified motor for a certain period of time to test operation.
6-136-004 Front Jogger Motor
6-136-005 Rear Jogger Motor
6-136-006 Shift Motor
6-136-007 Hitroll Motor
6-136-008 Exit Guide Plate Motor
6-136-009 Staple Moving Motor
6-136-010 Tray Motor
6-136-011 Staple Motor
6-136-012 Stopper Motor
6-136-013 Punch Motor
6-136-014 Punch Moving Motor
6-136-015 Punch Registration Moving
Motor
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
6162 [FIN (1K FIN) OUTPUT Check]
Continuously runs specified motor for operation test.
6-162-001 Entrance Transport Motor
6-162-002 Proof Transport Motor
6-162-003 Paper Feed/Positioning &
Move Roller Motor
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
6162 [FIN (1K FIN) OUTPUT Check]
Drives specified motor for a certain period of time to test operation.
6-162-004 Junction Solenoid ENG [0 or 1 / 0 / 1/step]
6-162-005 Shift Motor
6-162-006 Jogger Motor
ENG
ENG
ENG 6-162-007 Exit Guide Plate Open/
Close Motor
6-162-008 Feed-out Motor
6-162-009 Tray Lift Motor
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
6-162-011 Positioning Roller Motor
6-162-012 Stapler Shift Motor
6-162-013 Stapler Motor
6-162-014 Untitled
ENG
ENG
ENG
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
6-162-015 Untitled
6-162-016 Untitled
6-162-017 Punch Motor
6-162-018 Punch Move Motor
6-162-019 S-to-S Registration
Detection Move Motor
6-162-020 Stack Transport Motor:
Upper
6-162-021 Stck Trns Uppr Prss Rls/
Stndrd Fence Rtrct M
6-162-022 Stack Lower Pressure
Release Motor
6162 [FIN (1K FIN) OUTPUT Check]
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
[0 or 1 / 0 / 1/step]
Continuously runs specified motor for operation test.
6-162-023 Folder Transport Motor ENG [0 or 1 / 0 / 1/step]
Input and Output Check
493
494
3. Engine SP Mode Tables
6162 [FIN (1K FIN) OUTPUT Check]
Drives specified motor for a certain period of time to test operation.
6-162-024 TE Stopper Motor ENG [0 or 1 / 0 / 1/step]
6-162-025 Folder Blade Motor
6162 [FIN (1K FIN) OUTPUT Check]
ENG [0 or 1 / 0 / 1/step]
Lights all guide LED.
6-162-026 Navigation LED (All) ENG [0 or 1 / 0 / 1/step]
6185 [Output Check: NoStplBindFIN]
6-185-001 Transport Motor ENG [0 or 1 / 0 / 1/step]
Checks the transport motor’s movement of non staple finisher.
6-185-002 Shift Motor ENG [0 or 1 / 0 / 1/step]
Checks the shift motor’s movement of non staple finisher.
6-185-003 Junction Solenoid Motor ENG [0 or 1 / 0 / 1/step]
Checks the junction solenoid motor’s movement of non staple finisher.
6-185-004 Exit Pressure Release
Motor
ENG [0 or 1 / 0 / 1/step]
Checks the exit pressure release motor’s movement of non staple finisher.
6-185-005 Stapler Motor ENG [0 or 1 / 0 / 1/step]
Checks the stapler motor’s movement of non staple finisher.
Test Pattern Printing
Printing Test pattern: SP2-109
Some of these test patterns are used for copy image adjustments but most are used primarily for design testing.
• Do not operate the machine until the test pattern is printed out completely. Otherwise, SC will occur.
1. Enter the SP mode then select SP2-109-003.
2. Select test pattern for print from the list then press [OK].
3. When selecting color for Printing; Full Color or either CMYK, go to SP2-109-005 (1: Full Color, 2:
Cyan, 3: Magenta, 4: Yellow, 5: Black) to select.
4. When changing density of test pattern, select density with SP2-109-006 through 009 for each color.
• If select "0" with SP2-109-006 through 009, the color adjusted so will not show up in the test pattern.
5. To Print, Touch "Copy Window", then set settings within the following window for test print (paper size etc…).
1
2
3
4
0
No.
• When using black and white printing, touch "Black & White" on the LCD. When using color printing, touch "Full Color" on the LCD.
6. Press "Start" key to start test print.
7. After checking test pattern, touch "SP Mode" on the LCD to return to SP mode display.
8. Reset all settings to default values.
9. Exit SP mode.
Copy image
Pattern
Vertical Line (1dot)
Vertical Line (2dot)
Horizontal Line (1dot)
Horizontal Line (2dot)
No.
12
13
14
15
16
Pattern
Independent Pattern (2dot)
Independent Pattern (4dot)
Trimming Area
Hound's Tooth Check (Vertical)
Hound's Tooth Check (Horizontal)
495
496
3. Engine SP Mode Tables
9
10
11
7
8
5
6
No.
Pattern
Grid Vertical Line
Grid Horizontal Line
Grid Pattern Small
Grid Pattern Large
Argyle Pattern Small
Argyle Pattern Large
Independent Pattern (1dot)
21
22
23
No.
17
18
19
20
Pattern
Band (Horizontal)
Band (Vertical)
Checker Flag Pattern
Grayscale (Vertical Margin)
Grayscale (Horizontal Margin)
Wormy Pattern
Full Dot Pattern
5009 [Add Display Language]
Adds language available in user choice. (Only the languages registered in the machine)
Refer to the displayed language list to set in the way showed below.
List Number Assigned Bit Switch
No.1 to 8 BIT1 to 8 (SP5-009-201)
No.9 to 16 BIT1 to 8 (SP5-009-202)
No.17 to 24 BIT1 to 8 (SP5-009-203)
No.25 to 32 BIT1 to 8 (SP5-009-204)
No.33 to 40 BIT1 to 8 (SP5-009-205)
No.41 to 48 BIT1 to 8 (SP5-009-206)
No.49 to 56 BIT1 to 8 (SP5-009-207)
Example: To add American(No.3 in the list) or Czech (No.15)
Turn Bit 3 of “SP5-009-201” 0 to 1 for American.
Turn Bit 7 of “SP5-009-202” 0 to 1 for Czech.
After setting, turn the main power switch off and on to make the setting valid.
5-009-201 1-8 *CTL [1 to 255 / 0 / 1]
5-009-202 9-16
5-009-203 17-24
5-009-204 25-32
5-009-205 33-40
5-009-206 41-48
5-009-207 49-56
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[1 to 255 / 0 / 1]
[1 to 255 / 0 / 1]
[1 to 255 / 0 / 1]
[1 to 255 / 0 / 1]
[1 to 255 / 0 / 1]
[1 to 255 / 0 / 1]
497
498
4. Controller SP Mode Tables
5024 [mm/inch Display Selection]
Display units (mm or inch) for custom paper sizes.
5-024-001 0:mm 1:inch *CTL [0 or 1 / 1(USA), 0(Others) / 1]
0: mm
1: inch
5045 [Accounting counter]
5-045-001 Counter Method *CTL [0 to 7 / 1 / step]
0: Developments
1: Prints
2: Coverage
7: Coverage (YMC)
5047 [Paper Display]
5-047-001 Backing Paper *CTL [0 or 1 / 0 / 1]
0: OFF
1: ON
5051
5-051-001 -
[TonerRefillDetectionDisplay]
*CTL [0 or 1 / 0 / 1]
0: ON
1: OFF
5055
5-055-001 -
5061
[Display IP Address]
*CTL [0 or 1 / 0 / 1]
0: OFF
1: ON
[Toner Remaining Icon Display Change]
5-061-001 *CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
5062 [Parts Replacement Alert Display]
5-062-002 #Photoconductor Unit (Black)
5-062-003 #Development unit: Bk
5-062-025 #Photoconductor Unit (Cyan)
*CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
*CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
*CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-026 #Development unit: C
5-062-048 #Photoconductor Unit (Magenta) *CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-049 #Development unit: M
*CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-071 #Photoconductor Unit (Yellow)
*CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
*CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-072 #Development unit: Y *CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
Controller SP Tables - SP5000
499
500
4. Controller SP Mode Tables
5-062-093 #Intermediate Transfer Unit
5-062-102 #ITB Cleaning Unit
5-062-109 #Paper Transfer Unit
5-062-115 #Fuser Unit
5-062-116 Fuser Unit: Belt
5-062-118 Fuser Unit: Pressure Roller
5-062-131 #Dust Filter
5-062-142 #Wast Toner bottle
5-062-206 #ADF Pick-up Roller
5-062-207 #ADF Paper Supply Belt
*CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
*CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
*CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
*CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
*CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
*CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
*CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
*CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
*CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
*CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
5-062-208 #ADF Separate Roller *CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
5066
5-066-001 -
[PM Parts Display]
*CTL [0 or 1 / 0 / 1]
0: Not display
1: Display
5067 [Part Replacement Operation Type]
5-067-002 #Photoconductor Unit (Black) *CTL [0 or 1 / 0 / 1]
0: Service
1: User
5-067-003 #Development unit: Bk
5-067-025 #Photoconductor Unit (Cyan)
*CTL [0 or 1 / 0 / 1]
0: Service
1: User
*CTL [0 or 1 / 0 / 1]
0: Service
1: User
5-067-026 #Development unit: C
5-067-048 #Photoconductor Unit (Magenta) *CTL [0 or 1 / 0 / 1]
0: Service
1: User
5-067-049 #Development unit: M
*CTL [0 or 1 / 0 / 1]
0: Service
1: User
5-067-071 #Photoconductor Unit (Yellow)
*CTL [0 or 1 / 0 / 1]
0: Service
1: User
*CTL [0 or 1 / 0 / 1]
0: Service
1: User
Controller SP Tables - SP5000
501
502
4. Controller SP Mode Tables
5-067-072 #Development unit: Y
5-067-093 #Intermediate Transfer Unit
5-067-102 #ITB Cleaning Unit
5-067-109 #Paper Transfer Unit
5-067-115 #Fuser Unit
5-067-116 Fuser Unit: Belt
5-067-118 Fuser Unit: Pressure Roller
5-067-131 #Dust Filter
5-067-142 #Wast Toner bottle
5-067-206 #ADF Pick-up Roller
*CTL [0 or 1 / 0 / 1]
0: Service
1: User
*CTL [0 or 1 / 0 / 1]
0: Service
1: User
*CTL [0 or 1 / 0 / 1]
0: Service
1: User
*CTL [0 or 1 / 0 / 1]
0: Service
1: User
*CTL [0 or 1 / 0 / 1]
0: Service
1: User
*CTL [0 or 1 / 0 / 1]
0: Service
1: User
*CTL [0 or 1 / 0 / 1]
0: Service
1: User
*CTL [0 or 1 / 0 / 1]
0: Service
1: User
*CTL [0 or 1 / 0 / 1]
0: Service
1: User
*CTL [0 or 1 / 0 / 1]
0: Service
1: User
Controller SP Tables - SP5000
5-067-207 #ADF Paper Supply Belt
5-067-208 #ADF Separate Roller
*CTL [0 or 1 / 0 / 1]
0: Service
1: User
*CTL [0 or 1 / 0 / 1]
0: Service
1: User
5071
5-071-001 -
[Set Bypass Paper Size Display]
CTL [0 or 1 / 0 / 1]
0: Off
1: On
5073 [Supply Part Replacement Opration Type]
5-073-001 Waste Tonner Bottle *CTL [0 or 1 / 0 / 1]
0:No Display
1:Display
5074 [Home Screen Login]
5-074-002 Login Setting
5-074-050 Show Home Edit Menu
5-074-091 Function Setting
5-074-092 Product ID
5-074-093 Application Screen ID
*CTL
*CTL
[0 to 255 / 0 / 1]
[0 to 2 / 0 / 1]
*CTL [0 to 2 / 0 / 1]
0: Function disable
1: SDK application
2: Legacy application (reserved)
*CTL [0x00 to 0xffff / - / 1]
*CTL [0 to 255 / 0 / 1]
5075 [USB Keyboard]
503
504
4. Controller SP Mode Tables
5-075-003 Display setting *CTL [0 or 1 / 0 / 1]
0: Disable
1: Enable
5081 [ServiceSP Entery Code Setting]
DFU
5-081-001 ServiceSP Entery Code Setting
5083 [LED Light Switch Setting]
5-083-001 Toner Near End
5-083-002 Waste Toner Near End
-
*CTL [0 or 1 / 0 / 1]
0: OFF
1: ON
*CTL [0 or 1 / 0 / 1]
5102 [AutoDetect]
5-102-203 HumanDetectSetting
5114 [Optional Counter I/F]
5-114-001 MF Key Card Extension
*CTL [0 or 1 / 0 / 1]
*CTL [0 or 1 / 0 / 1]
0: Not installed
1: Installed (scanning accounting)
5118
5-118-001 -
[Disable Copying]
*CTL [0 or 1 / 0 / 1]
0: Not disabled
1: Disabled
5120 [Mode Clear Opt. Counter Removal]
Controller SP Tables - SP5000
5-120-001 0:Yes 1:StandBy 2:No *CTL [0 to 2 / 0 / 1]
0: Yes (removed)
1: Standby (installed but not used)
2: No (not removed)
5121 [Counter Up Timing]
5-121-001 0:Feed 1:Exit *CTL [0 or 1 / 0 / 1]
0: Feed
1: Exit
5127
5-127-001 -
[APS Mode]
*CTL [0 or 1 / 0 / 1]
0: Not disabled
1: Disabled
5148 [Size Detection Off]
5-148-002 Tray 1
5150 [Length Setting]
5-150-001 Bypass(0:OFF 1:Long)
*CTL [0 or 1 / 0 / 1]
CTL [0 or 1 / 0 / 1]
0: OFF
1: ON
5162
5-162-001 -
5167
[App. Switch Method]
*CTL [0 or 1 / 0 / 1]
0: Soft Key Set
1: Hard Key Set
[Fax Printing Mode at Optional Counter Off]
505
506
4. Controller SP Mode Tables
5-167-001 *CTL [0 or 1 / 0 / 1]
0: Automatic printing
1: No automatic printing
5169
5-169-001
[CE Login]
*CTL [0 or 1 / 0 / 1]
0: Disabled
1: Enabled
5188
5-188-001 -
[Copy Nv Version]
5191 [Mode Set]
5-191-001 Power Str Set
*CTL [- / - / -]
*CTL [0 or 1 / 1 / 1]
0: OFF
1: ON
5193
5-193-001 -
[External Controller Info. Settings]
CTL [0 to 10 / 0 / 1]
0: External Controller is not installed
1: EFI
2: Ratio
3: Egret
4: GJ
5:Creo
6: QX-100
7: Kurofune
8 to 10: Reserved
5195 [Limitless SW]
Controller SP Tables - SP5000
5-195-001 *CTL [0 or 1 / 0 / 1]
0: Productivity Precede
1: Use paper up
5196 [Copier Vendor Mode]
5-196-001 90 deg. Rotation
5-196-002 Color and Tray Selection
CTL [0 or 1 / 0 / 1]
CTL [0 or 1 / 0 / 1]
5199 [Paper Exit After Staple End]
5-199-001 Staple(1:Without 2:After 0:Auto) CTL [0 to 2 / 0 / 1]
5-199-002 Saddle(1:Without 2:After 0:Auto) CTL [0 to 2 / 0 / 1]
5-199-003 Stapless(1:Without 2:After
0:Auto)
CTL [0 to 2 / 0 / 1]
5212 [Page Numbering]
5-212-003 Duplex Printout Left/Right Position of Left/Right Facing
5-212-004 Duplex Printout Top/Bottom
Position of Left/Right Facing
5-212-018 Duplex Printout Left/Right Position of Top/Bottom Facing
5-212-019 Duplex Printout Top/Bottom
Position of Top/Bottom Facing
*CTL [-10 to 10 / 0 / 0.01mm/step]
*CTL [-10 to 10 / 0 / 0.01mm/step]
*CTL [-10 to 10 / 0 / 0.01mm/step]
*CTL [-10 to 10 / 0 / 0.01mm/step]
5227 [Page numbering]
5-227-201 Allow Page No. Entry
5-227-202 Zero Surplus Stting
*CTL [2 to 9 / 9 / 1]
*CTL [0 or 1 / 0 / 1]
0:OFF
1:ON
507
508
4. Controller SP Mode Tables
5302 [Set Time]
Adjusts the RTC (real time clock) time setting for the local time zone.
Examples: For Japan (+9 GMT), enter 540 (9 hours x 60 min.)
DOM: +540 (Tokyo)
NA: -300 (New York)
EU: + 60 (Paris)
CH: +480 (Beijing)
TW: +480 (Taipei)
AS: +480 (Hong Kong)
5-302-002 Time Difference *CTL [-1440 to 1440 / - / 1min/step]
5305 [Auto Off Set]
5-305-101 Auto Off Limit Set *CTL [0 or 1 / 1 / 1]
5307 [Daylight Saving Time]
5-307-001 Setting *CTL [0 to 1 / - / 1]
0: Disabled
1: Enabled
(Default)
1: NA and EUR
0: ASIA and others
Enables or disables the summer time mode.
• Make sure that both SP5-307-3 and -4 are correctly set. Otherwise, this SP is not activated even if this SP is set to "1".
Controller SP Tables - SP5000
5-307-003 Rule Set (Start) *CTL [0 to 0xffffffff / - / 1hex]
(Default)
NA: 0x11100200
EUR: 0x10500100
ASIA: 0x03100000
Other: 0x00000000
Specifies the start setting for the summer time mode.
There are 8 digits in this SP. For months 1 to 9, the "0" cannot be input in the first digit, so the eight-digit setting for -2 or -3 becomes a seven-digit setting.
1st and 2nd digits: The month. [1 to 12]
3rd digit: The week of the month. [1 to 5]
4th digit: The day of the week. [0 to 6 = Sunday to Saturday]
5th and 6th digits: The hour. [00 to 23]
7th digit: The length of the advanced time. [0 to 9 / 1 hour ]
8th digit: The length of the advanced time. [0 to 5 / 10 minutes ]
• The digits are counted from the left.
• Make sure that SP5-307-1 is set to "1".
5-307-004 Rule Set (End) *CTL [0 to 0xffffffff / - / 1hex]
Specifies the end setting for the summer time mode.
There are 8 digits in this SP.
1st and 2nd digits: The month. [1 to 12]
3rd digit: The week of the month. [0 to 5]
4th digit: The day of the week. [0 to 7 = Sunday to Saturday]
5th and 6th digits: The hour. [00 to 23]
The 7th and 8 digits must be set to "00".
• The digits are counted from the left.
• Make sure that SP5-307-1 is set to "1".
5401 [Access Control]
5-401-103 Default Document ACL
5-401-104 Authentication Time
CTL
CTL
[0 to 3 / 0 / 1]
[0 to 255 / 0 / 1sec/step]
509
510
4. Controller SP Mode Tables
5-401-162 Extend Certification Detail
5-401-200 SDK1 UniqueID
5-401-201 SDK1 Certification Method
5-401-210 SDK2 UniqueID
5-401-211 SDK2 Certification Method
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xFFFFFFFF / 0 / 1]
CTL [0 to 0xFF / 0 / 1]
CTL [0 to 0xFFFFFFFF / 0 / 1]
CTL [0 to 0xFF / 0 / 1]
5-401-220 SDK3 UniqueID
5-401-221 SDK3 Certification Method
5-401-230 SDK Certification Device
CTL [0 to 0xFFFFFFFF / 0 / 1]
CTL [0 to 0xFF / 0 / 1]
*CTL [0 to 7 / 0 / power of 2]
0-1: SDK authentication available
0-0: Disable all functions
1-1: SKB Display
1-0: Disable
2-1: Administrator login
2-0: Disable
3 to 7-0: Reserved (set “0” only)
5-401-240 Detail Option *CTL [0 to 7 / 0x00 / 0x01]
0: Logout confirm option
-1: ON, 0: OFF
2 to 1: Auto-logout timer(retry timer)
-11: 30sec, 10: 20sec, 01: 10sec, 00: 60sec
3: personal authority / Group authority and operation
-1: ON, 0: OFF
4: Skip password entry
-1: ON, 0: OFF
5: Set the display of the remaining Frequence
-1: ON, 0: OFF
6 to 7: Set the display time
-1: ON, 0: OFF
5402 [Access Control]
5-402-101 SDKJ1 Limit Setting
5-402-102 SDKJ2 Limit Setting
5-402-103 SDKJ3 Limit Setting
5-402-104 SDKJ4 Limit Setting
5-402-105 SDKJ5 Limit Setting
5-402-106 SDKJ6 Limit Setting
5-402-107 SDKJ7 Limit Setting
5-402-108 SDKJ8 Limit Setting
5-402-109 SDKJ9 Limit Setting
5-402-110 SDKJ10 Limit Setting
5-402-111 SDKJ11 Limit Setting
5-402-112 SDKJ12 Limit Setting
5-402-113 SDKJ13 Limit Setting
5-402-114 SDKJ14 Limit Setting
5-402-115 SDKJ15 Limit Setting
5-402-116 SDKJ16 Limit Setting
5-402-117 SDKJ17 Limit Setting
5-402-118 SDKJ18 Limit Setting
5-402-119 SDKJ19 Limit Setting
5-402-120 SDKJ20 Limit Setting
5-402-121 SDKJ21 Limit Setting
5-402-122 SDKJ22 Limit Setting
5-402-123 SDKJ23 Limit Setting
5-402-124 SDKJ24 Limit Setting
5-402-125 SDKJ25 Limit Setting
5-402-126 SDKJ26 Limit Setting
Controller SP Tables - SP5000
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
511
512
4. Controller SP Mode Tables
5-402-127 SDKJ27 Limit Setting
5-402-128 SDKJ28 Limit Setting
5-402-129 SDKJ29 Limit Setting
5-402-130 SDKJ30 Limit Setting
5-402-141 SDKJ1 ProductID
5-402-142 SDKJ2 ProductID
5-402-143 SDKJ3 ProductID
5-402-144 SDKJ4 ProductID
5-402-145 SDKJ5 ProductID
5-402-146 SDKJ6 ProductID
5-402-147 SDKJ7 ProductID
5-402-148 SDKJ8 ProductID
5-402-149 SDKJ9 ProductID
5-402-150 SDKJ10 ProductID
5-402-151 SDKJ11 ProductID
5-402-152 SDKJ12 ProductID
5-402-153 SDKJ13 ProductID
5-402-154 SDKJ14 ProductID
5-402-155 SDKJ15 ProductID
5-402-156 SDKJ16 ProductID
5-402-157 SDKJ17 ProductID
5-402-158 SDKJ18 ProductID
5-402-159 SDKJ19 ProductID
5-402-160 SDKJ20 ProductID
5-402-161 SDKJ21 ProductID
5-402-162 SDKJ22 ProductID
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
Controller SP Tables - SP5000
5-402-163 SDKJ23 ProductID
5-402-164 SDKJ24 ProductID
5-402-165 SDKJ25 ProductID
5-402-166 SDKJ26 ProductID
5-402-167 SDKJ27 ProductID
5-402-168 SDKJ28 ProductID
5-402-169 SDKJ29 ProductID
5-402-170 SDKJ30 ProductID
5404 [User Code Count Clear]
5-404-001 User Code Count Clear
5-404-101 User Code Count Clear Permit
Setting
5411 [LDAP-Certification]
5-411-004 Easy Certification
5-411-005 Password Null Not Permit
5-411-006 Detail Option
CTL
CTL
CTL
CTL
CTL
CTL
*CTL
*CTL
[0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
CTL [0 to 0xffffffff / 0 / 1]
[0 to 0xffffffff / 0 / 1]
[0 to 0xffffffff / 0 / 1]
[0 to 0xffffffff / 0 / 1]
[0 to 0xffffffff / 0 / 1]
[0 to 0xffffffff / 0 / 1]
[- / - / -]
[Execute]
[0 or 1 / 0 / 1]
*CTL [0 or 1 / 1 / 1]
1: On
0: Off
*CTL [0 or 1 / 0 / 1]
0: Password NULL not permitted.
1: Password NULL permitted.
*CTL [0 or 1 / 0 / 1]
0: OFF
1: ON
5412 [Krb-Certification]
5-412-100 Encrypt Mode CTL [0 to 0xFF / 0x1F / 1]
513
514
4. Controller SP Mode Tables
5413 [Lockout Setting]
5-413-001 Lockout On/Off
5-413-002 Lockout Threshold
5-413-003 Cancellation On/Off
*CTL [0 or 1 / 0 / 1]
0: Off
1: On
*CTL [1 to 10 / 5 / 1]
*CTL [0 or 1 / 0 / 1]
0: Off (no wait time, lockout not cancelled)
1: On (system waits, cancels lockout if correct user ID and password are entered.
*CTL [1 to 9999 / 60 / 1min] 5-413-004 Cancellation Time
5414 [Access Mitigation]
5-414-001 Mitigation On/Off
5-414-002 Mitigation Time
5415 [Password Attack]
5-415-001 Permissible Number
5-415-002 Detect Time
5416 [Access Information]
5-416-001 Access User Max Num
5-416-002 Access Password Max Num
5-416-003 Monitor Interval
5417 [Access Attack]
5-417-001 Access Permissible Number
*CTL [0 or 1 / 0 / 1]
0: OFF
1: ON
*CTL [0 to 60 / 15 / 1min/step]
*CTL [0 to 100 / 30 /1attempt/step]
*CTL [1 to 10 / 5 / 1sec/step]
*CTL [50 to 200 / 200 / 1user/step]
*CTL [50 to 200 / 200 / 1password/step]
*CTL [1 to 10 / 3 / 1sec/step]
*CTL [0 to 500 / 100 / 1/step]
5-417-002 Attack Detect Time
5-417-003 Productivity Fall Wait
5-417-004 Attack Max Num
5420 [User Authentication]
5-420-001 Copy
5-420-002 Color Security Setting
5-420-011 DocumentServer
5-420-021 Fax
5-420-031 Scanner
5-420-041 Printer
5-420-051 SDK1
5-420-061 SDK2
5-420-071 SDK3
5-420-081 Browser
5430 [Auth Dialog Message Change]
Controller SP Tables - SP5000
*CTL [10 to 30 / 10 / 1sec/step]
*CTL [0 to 9 / 3 / 1sec/step]
*CTL [50 to 200 / 200 / 1attempt/step]
*CTL [0 to 1 / 0 / 1]
0: On
1: Off
*CTL [0x00 to 0xFF / 0x00 / 1]
*CTL [0 or 1/ 0 / 1]
0: On
1: Off
*CTL [0 or 1/ 0 / 1]
0: On
1: Off
*CTL [0 or 1/ 0 / 1]
0: On
1: Off
*CTL [0 or 1/ 0 / 1]
0: On
1: Off
*CTL [0 or 1 / 0 / 1]
*CTL
0: ON
1: OFF
*CTL
*CTL [0 or 1 / 0 / 1]
0: ON
1: OFF
515
516
4. Controller SP Mode Tables
5-430-001 Message Change On/Off
5-430-002 Message Text Download
5-430-003 Message Text ID
5431 [External Auth User Preset]
5-431-010 Tag
5-431-011 Entry
5-431-012 Group
5-431-020 Mail
5-431-030 Fax
5-431-031 FaxSub
5-431-032 Folder
5-431-033 ProtectCode
5-431-034 SmtpAuth
5-431-035 LdapAuth
5-431-036 Smb Ftp Fldr Auth
5-431-037 AcntAcl
5-431-038 DocumentAcl
5-431-040 CertCrypt
5-431-050 UserLimitCount
5481 [Authentication Error Code]
5-481-001 System Log Disp
CTL [0 or 1 / 0 / 1]
CTL [- / - / -]
CTL [- / - / -]
CTL [0 or 1 / 1 / 1]
CTL [0 or 1 / 1 / 1]
CTL [0 or 1 / 1 / 1]
CTL [0 or 1 / 1 / 1]
CTL [0 or 1 / 1 / 1]
CTL [0 or 1 / 1 / 1]
CTL [0 or 1 / 1 / 1]
CTL [0 or 1 / 1 / 1]
CTL [0 or 1 / 1 / 1]
CTL [0 or 1 / 1 / 1]
CTL [0 or 1 / 1 / 1]
CTL [0 or 1 / 1 / 1]
CTL [0 or 1 / 1 / 1]
CTL [0 or 1 / 0 / 1]
CTL [0 or 1 / 1 / 1]
*CTL [0 or 1 / 0 / 1]
0: Off
1: On
5-481-002 Panel Disp
5490 [MF KeyCard (Japan only)]
5-490-001 Job Permit Setting
5-490-002 Count Mode Setting
5491 [Optional Counter]
5-491-001 Detail Option
5501 [PM Alarm]
5-501-001 PM Alarm Level
*CTL [0 to 1 / 0 / 1]
0: Disabled. Cancels operation without a user code.
1: Enabled. Allows operation without a user code.
*CTL -
*CTL [0 to 0xff / 0 / 1]
*CTL [0 to 9999 / 0 / 1]
0: Alarm off
1 to 9999: Alarm goes off when Value
(1 to 9999) x 1000 > PM counter
5504
5-504-001 -
[Jam Alarm]
*CTL [0 or 1 / 0 / 1]
1: On
0: Off
Controller SP Tables - SP5000
*CTL [0 to 3 / 3 / 1]
0: Z
1: L
2: M
3: H
*CTL [1 to 99 / 10 / 1] 5-504-002 Threshold
5505 [Error Alarm]
517
518
4. Controller SP Mode Tables
5-505-001 Error Alarm
5-505-002 Threshold
5507 [Supply/CC Alarm]
5-507-001 Paper Supply Alarm
5-507-002 Staple Supply Alarm
5-507-003 Toner Supply Alarm
5-507-006 WasteTonerBottle
5-507-080 Toner Call Timing
5-507-080 Toner Call Timing
5-507-081 Toner Call Threshold:Bk
5-507-082 Toner Call Threshold:CMY
5-507-128 Interval :Others
5-507-132 Interval :A3
*CTL [0 to 255 / * / 1 x10
2
sheets/step]
0: Alarm Off
* C2503 :20 / C2003:15
*CTL [1 to 99 / 5 / 1]
*CTL [0 or 1 / 0 / 1]
0: OFF
1: ON
*CTL [0 or 1 / 0 / 1]
0: OFF
1: ON
*CTL [0 or 1 / 0 / 1]
0: OFF
1: ON
*CTL [0 to 2 / 1 / 1]
0:OFF
1: Supply Call ON
2: CC Call ON
*CTL [0 or 1 / 0 / 1]
0: Toner bottle replacement
1: Less than toner threshold
CTL [0 or 1 / 0 / 1]
CTL [10 to 90 / 10 / 10%/step]
CTL [10 to 90 / 10 / 10%/step]
*CTL [250 to 10000 / 1000 / 1page/ step]
*CTL [250 to 10000 / 1000 / 1page/ step]
Controller SP Tables - SP5000
5-507-133 Interval :A4
5-507-134 Interval :A5
5-507-141 Interval :B4
5-507-142 Interval :B5
5-507-160 Interval :DLT
5-507-164 Interval: LG
5-507-166 Interval :LT
5-507-172 Interval :HLT
5508 [CC Call]
5-508-001 Jam Remains
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[250 to 10000 / 1000 / 1page/ step]
[250 to 10000 / 1000 / 1page/ step]
[250 to 10000 / 1000 / 1page/ step]
[250 to 10000 / 1000 / 1page/ step]
[250 to 10000 / 1000 / 1page/ step]
[250 to 10000 / 1000 / 1page/ step]
[250 to 10000 / 1000 / 1page/ step]
[250 to 10000 / 1000 / 1page/ step]
5-508-002 Continuous Jams
5-508-003 Continuous Door Open
5-508-011 Jam Detection: Time Length
5-508-012 Jam Detection: Continuous
Count
5-508-013 Door Open: Time Length
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[0 or 1 / 1 / 1]
0: Disable
1: Enable
[0 or 1 / 1 / 1]
0: Disable
1: Enable
[0 or 1 / 1 / 1]
0: Disable
1: Enable
[3 to 30 / 10 / 1min/step]
[2 to 10 / 5 / 1time/step]
[3 to 30 / 10 / 1min/step]
519
520
4. Controller SP Mode Tables
5513 [PartsAlermlevelCount]
5-513-001 Normal
5-513-002 Df
5514 [PartsAlermlev]
5-514-001 Normal
5-514-002 Df
5515 [SC/Alarm Setting]
5-515-001 SC Call
5-515-002 Service Parts Near End Call
5-515-003 Service Parts End Call
5-515-004 User Call
5-515-006 Communication Test Call
5-515-007 Machine Information Notice
5-515-008 Alarm Notice
5-515-009 Non Genuine Tonner Ararm
5-515-010 Supply Automatic Ordering
Call
5-515-011 Supply Management Report
Call
5-515-012 Jam/Door Open Call
5-515-050 Timeout:Manual Call
5-515-051 Timeout:Other Call
5517 [Get Machine Information]
5-517-031 Get SMC Info: Retry Interval
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[1 to 9999 / 300 / 1]
[1 to 9999 / 300 / 1]
[0 or 1 / 1 / 1]
[0 or 1 / 0 / 1]
[0 or 1 / 1 / 1]
0: OFF
1: ON
[1 to 255 / 5 / 1min/step]
[1 to 255 / 10 / 1min/step]
*CTL [10 to 255 / 10 / 1min/step]
Controller SP Tables - SP5000
5618
5-618-001 -
[Color Mode Display Selection]
*CTL [0 or 1 / 1 / 1]
0: ACS, Color, Black & White, Two
Colors, Single color
1: ACD, Full Color, Black & White
5728 [Network Setting]
5-728-001 NAT Machine Port1
5-728-002 NAT UI Port1
5-728-003 NAT Machine Port2
5-728-004 NAT UI Port2
5-728-005 NAT Machine Port3
5-728-006 NAT UI Port3
5-728-007 NAT Machine Port4
5-728-008 NAT UI Port4
5-728-009 NAT Machine Port5
5-728-010 NAT UI Port5
5-728-011 NAT Machine Port6
5-728-012 NAT UI Port6
5-728-013 NAT Machine Port7
5-728-014 NAT UI Port7
5-728-015 NAT Machine Port8
5-728-016 NAT UI Port8
5-728-017 NAT Machine Port9
5-728-018 NAT UI Port9
5-728-019 NAT Machine Port10
5-728-020 NAT UI Port10
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
[1 to 65535 / 49101 / 1]
[1 to 65535 / 55101 / 1]
[1 to 65535 / 49102 / 1]
[1 to 65535 / 55102 / 1]
[1 to 65535 / 49103 / 1]
[1 to 65535 / 55103 / 1]
[1 to 65535 / 49104 / 1]
[1 to 65535 / 55104 / 1]
[1 to 65535 / 49105 / 1]
[1 to 65535 / 55105 / 1]
[1 to 65535 / 49106 / 1]
[1 to 65535 / 55106 / 1]
[1 to 65535 / 49107 / 1]
[1 to 65535 / 55107 / 1]
[1 to 65535 / 49108 / 1]
[1 to 65535 / 55108 / 1]
[1 to 65535 / 49109 / 1]
[1 to 65535 / 55109 / 1]
[1 to 65535 / 49110 / 1]
[1 to 65535 / 55110 / 1]
521
4. Controller SP Mode Tables
522
5730 [Extended Function Setting]
5-730-001 JavaTM Platform setting
5-730-010 Expiration Prior Alarm Set
*CTL
*CTL
[0 or 1 / 1 / -]
0: Disable, 1: Enable
[0 to 999 / 20 / 1day/step]
5731 [Counter Effect]
This SP is used only for DOM machines.
5-731-001 Change MK1 Cnt (Paper-
>Combine)
*CTL [0 or 1 / 0 / 1]
5732
5-732-002
[Reset Job After Jam(Copy)]
5734 [PDF Setting]
5-734-001 PDF/A Fixed
*CTL
*CTL
[0 or 1 / 0 / 1]
[0 or 1 / 0 / 1]
5741
5-741-001
[Node Authentication Timuout]
5745 [DeemedPowerConsumption]
5-745-211 Controller Standby
5-745-212 STR
5-745-213 Main Power Off
5-745-214 Scanning and Printing
5-745-215 Printing
5-745-216 Scanning
5-745-217 Engine Standby
5-745-218 Low Power Consumption
5-745-219 Silent condition
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[1 to 255 / 60 / 1sec/step]
[0 to 9999 / 0 / 1]
[0 to 9999 / 0 / 1]
[0 to 9999 / 0 / 1]
*CTL [0 to 9999 / 0 / 1]
*CTL [0 to 9999 / 0 / 1]
*CTL [0 to 9999 / 0 / 1]
[0 to 9999 / 0 / 1]
[0 to 9999 / 0 / 1]
[0 to 9999 / 0 / 1]
Controller SP Tables - SP5000
5-745-220 Heater Off
5748 [OpePanel Setting]
5-748-101 Op Type Action Setting
*CTL [0 to 9999 / 0 / 1]
5-748-201 Cheetah Panel Connect Setting
CTL
CTL
[0x00 to 0xFF / 0 / 0x01]
• bit0
0: Normal operation panel
1: Smart operation panel
[0 or 1 / 0 / 0]
0: OFF
1: ON
5749 [Import/Export]
5-749-001 Export
5-749-101 Import
CTL [- / - / -]
Target: System, Printer, Fax, Scanner
Option: Unique, Secret
Copy config: Encryption, Encryption key(if selected)
[Execute]
CTL [- / - / -]
Option: Unique
Copy config: Encryption, Encryption key(if selected)
[Execute]
5751 [Key Event Encryption Setting]
5-751-001 Password CTL [0 to 255 / 0 / 1]
5752 [Copy:WebAPI Setting]
5-752-001 Copy FlairAPI Setting
Bit Setting
0
*CTL * see BitSwitch below: meanings
Description
1
523
524
4. Controller SP Mode Tables bit 0 bit 1 bit 2 bit 3 bit 4 bit 5
Start of FlairAPI
Server
Access permission of FlairAPI from outside of the machine
Reserved
Reserved
Simple UI Function
Accessing permission of
Simple UI from outside of the machine bit 6 bit 7
Reserved
Reserved
5755 [Display Setting]
5-755-001 Disp Administrator Password
Change Scrn
5-755-002 Hide Administrator Password
Change Scrn
-
-
Off
(Do not Start)
Disabled
-
-
Disabled
Disabled
On
(Start)
Enabled
-
-
Enabled
Enabled
-
-
Sets whether to start exclusive
FlairAPI http server. If it is 0, scanning FlairAPI function and simple UI function will be disabled. The machine installed Android operating panel option, set “1”, others set “0”.
If it is “0”, accessing is limited from the machine only, such as operating panel, SDK/J,
MFP browsers etc... If it is “1”, accessing is allowed from outside of FlairAPI such as PC,
Remote UI, IT-Box etc...
-
-
If it is “1”, the machine can be used Scanner Simple UI. If it is
“0”, requesting URL of Simple
UI returns “404 Not Found”
If it is “0”, accessing is limited from the machine only
(operating panel and MFP browser). If it is “1”, accessing is allowed from outside of
Simple UI such as PC, mobile devices, and so on.
-
-
CTL
CTL
[- / - / -]
[- / - / -]
Controller SP Tables - SP5000
5758 [RemoteUI Setting]
5-758-001 Authentication
RTB 28
Deleted
5759 [Machine Limit Count]
5-759-001 Machine Limit Count Setting
5-759-061 Full Color Limit Count
5-759-062 Mono Color Limit Count
5801 [Memory Clear]
5-801-001 All Clear
5-801-003 SCS
5-801-004 IMH Memory Clr
5-801-005 Mcs
5-801-006 Copier Application
5-801-007 Fax Application
*CTL [0 or 1 / 0 / 1]
*CTL [0 or 1 / 0 / 1]
*CTL [0 to 99999999 / 0 / 1]
*CTL [0 to 99999999 / 0 / 1]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
525
526
4. Controller SP Mode Tables
5-801-008 Printer Application
The following service settings:
• Bit switches
• Gamma settings (User & Service)
• Toner Limit
The following user settings:
• Tray Priority
• Menu Protect
• System Setting except for setting of Energy Saver
• I/F Setup (I/O Buffer and I/O Timeout)
• PCL Menu
5-801-009 Scanner Application
CTL [- / - / -]
[Execute]
5-801-010 Web Service
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
5-801-011 NCS
5-801-012 R-Fax
5-801-014 Clear DCS Setting
5-801-015 Clear UCS Setting
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
5-801-016 MIRS Memory Clr
5-801-017 CCS
5-801-018 SRM Memory Clr
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
5-801-019 LCS Memory Clr
5-801-020 Web Uapli
5-801-021 ECS
5-801-023 AICS
5-801-025 Websys
5-801-026 PLN
5-801-027 SAS
5-801-028 Rest WebService
5812 [Service Tel. No. Setting]
5-812-001 Service
5-812-002 Facsimile
5-812-003 Supply
5-812-004 Operation
5816 [Remote Service]
5-816-001 I/F Setting
Controller SP Tables - SP5000
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
*CTL [up to 20 / - / 1]
*CTL [up to 20 / - / 1]
*CTL [up to 20 / - / 1]
*CTL [up to 20 / - / 1]
*CTL [0 to 2 / 2 / 1]
0: Remote service off
1: CSS remote service on
2: NRS remote service on
527
528
4. Controller SP Mode Tables
5-816-002 CE Call
5-816-003 Function Flag
5-816-007 SSL Disable
5-816-008 RCG Connect Timeout
5-816-009 RCG Write Timeout
5-816-010 RCG Read Timeout
5-816-011 Port 80 Enable
5-816-013 RFU Timing
5-816-014 RCG Error Cause
5-816-021 RCG – C Registed
5-816-023 connect type(N/M)
5-816-061 Cert Expire Timing
*CTL [0 or 1 / 0 / 1]
0: Start of the service
1: End of the service
*CTL [0 or 1 / 0 / 1]
0: Disabled
1: Enabled
*CTL [0 or 1 / 0 / 1]
0: Yes. SSL not used.
1: No. SSL used.
*CTL [1 to 90 / 30 / 1second/step]
*CTL [0 to 100 / 60 / 1second/step]
*CTL [0 to 100 / 60 / 1second/step]
*CTL [0 or 1 / 0 / 1]
0: No. Access denied
1: Yes. Access granted.
*CTL [0 or 1 / 1 / 1]
0: Any status of a target machine
1: Sleep or panel off mode only
CTL [0 or 1 / 0 / 1]
0: Initial state, normal condition
1: Error
*CTL [0 or 1 / 0 / 1]
0: Installation not completed
1: Installation completed
*CTL [0 or 1 / 0 / 1]
0: internet connection
1: Dial-up connection
*CTL [0 to 0xffffffff / 0 / 1]
0: Not use
1: Use
5-816-062 Use Proxy
5-816-063 Proxy Host
5-816-064 Proxy PortNumber
5-816-065 Proxy User Name
5-816-066 Proxy Password
Controller SP Tables - SP5000
*CTL [0 or 1 / 0 / 1]
0: Not use
1: Use
*CTL [- / - / -]
*CTL [0 to 0xffff / 0 / 1]
*CTL [up to 31 / - / 1]
*CTL [up to 31 / - / 1]
529
530
4. Controller SP Mode Tables
5-816-067 Proxy Password *CTL [0 to 255 / 0 / 1]
Displays status of the certification used for Cumin.
If it is not installed as Cumin, the value of this SP will be set when it installed, after checking the certification status.
0 The certification adequately set on the machine.
1
2
Request for certification update in progress.
Certification Update completed and notification of the success status to the
G/W in progress.
Certification Update failed and notification of the result to the G/W in progress.
3
4 Certification expiration date will be coming soon. Notifying the G/W to request for certification update.
11 Rescue certification setting for connecting to the rescue G/W in progress because update for rescue certification needed.
12 Setting for rescue certification has completed. Requesting to the rescue G/W for updating certification.
13 Notification for certification updating request has completed. Waiting for the certification update request from the rescue G/W.
14 Received the notification for certification updating request from the rescue
G/W. Writing the certification.
15 Writing the certification has completed. Notifying the result of certification update to the G/W.
16 Writing the certification has failed. Notifying the result of certification update to the G/W.
17 Writing a rescue certification because received a certification error again after completed the certification update request from the G/W and noticed the result of certification update with the updated certification.
18 The writing operation mentioned in #17 has completed. Notifying the result of certification update to the rescue G/W.
Controller SP Tables - SP5000
5-816-068 CERT: Error *CTL [0 to 255 / 0 / 1]
Displays a number code that describes the reason for the request for update of the certification.
0 Normal. There is no request for certification update in progress.
1 Request for certification update in progress. The current certification has expired.
2 An SSL error notification has been issued. Issued after the certification has expired.
3 Notification of shift from a common authentication to an individual certification.
4 Notification of a common certification without ID2.
5 Notification that no certification was issued.
6 Notification that GW URL does not exist.
5-816-069 CERT: Up ID *CTL [- / - / -]
-
5-816-083 Firm Up Status *CTL [0 to 5 / 0 / 1]
0: Waiting for accepting firm update
1: Waiting for firm update start schedule
2: Waiting for user confirmation
3: In preparation for the machine firm update
4: processing the machine firm update
5: processing the closing operation of the machine firm update
CTL [- / - / -] 5-816-085 Firm Up User Check
5-816-086 Firmware Size
5-816-087 CERT:Macro Ver.
5-816-088 CERT:PAC Ver.
5-816-089 CERT:ID2Code
CTL
CTL
CTL
CTL
[- / - / -]
[8digits / - / 1digit/step]
[16digits / - / 1digit/step]
[17digits / - / 1digit/step]
531
532
4. Controller SP Mode Tables
5-816-090 CERT:Subject
5-816-091 CERT:Serial No.
5-816-092 CERT:Issuer
5-816-093 CERT:Valid Start
5-816-094 CERT:Valid End
5-816-102 CERT:Encrypt Level
5-816-103 Client Communication Method
CTL [17digits / - / 1digit/step]
CTL [16digits / - / 1digit/step]
CTL [30digits / - / 1digit/step]
CTL [10digits / - / 1digit/step]
CTL [10digits / - / 1digit/step]
*CTL [1 to 2 / 1 / 1]
CTL [0 to 3 / 0 / 1]
5-816-104 Client Communication Limit CTL [1 to 7 / 7 / 1]
5-816-115 Network Information Waiting timer CTL [5 to 255 / 5 / 1sec/step]
5-816-150 Selection Country CTL [0 to 10 / 1 / 1]
0: Japan
1: USA
2: Canada
3: UK
4: Germany
5: France
6: Italy
7: Netherlands
8: Belgium
9: Luxembourg
10: Spain
Select the country where embedded RCG-M is installed in the machine. After selecting the country, you must also set the following SP codes for embedded RCG-M:
• SP5816-153
• SP5816-154
• SP5816-161
5-816-151 Line Type AutomaticJudgment CTL [- / - / -]
[Execute]
Controller SP Tables - SP5000
5-816-152 Line Type Judgment Result CTL [0 to 9 / - / 1]
Displays a number to show the result of the execution of SP5816 151. Here is a list of what the numbers mean.
0: Success
1: In progress (no result yet). Please wait.
2: Line abnormal
3: Cannot detect dial tone automatically
4: Line is disconnected
5: Insufficient electrical power supply
6: Line classification not supported
7: Error because fax transmission in progress – ioctl() occurred.
8: Other error occurred
9: Line classification still in progress. Please wait.
5-816-153 Selection Dial / Push CTL [0 or 1 / 0 / 1 ]
0: Tone Dialing Phone
1: Pulse Dialing Phone
Inside Japan "2" may also be displayed:
0: Tone Dialing Phone
1: Pulse Dialing Phone 10PPS
2: Pulse Dialing Phone 20PPS
5-816-154 Outside Line Outgoing Number
5-816-156 Dial Up User Name
5-816-157 Dial Up Password
5-816-161 Local Phone Number
5-816-162 Connection Timing Adjustment
Incoming
5-816-163 Access Point
5-816-164 Line Connecting
CTL
CTL
CTL
CTL
CTL
CTL
[- / - / -]
[up to 32 / - / 1]
[up to 32 / - / 1]
[up to 24 / - / 1]
[0 to 24 / 1 / 1]
[0 to 16 / 0 / 1]
CTL [0 to 1 / 0 / 1]
0: Sharing Fax
1: No Sharing Fax
533
534
4. Controller SP Mode Tables
5-816-173 Modem Serial No.
5-816-174 Retransmission Limit
5-816-187 FAX TX Priority
5-816-190 3G DongleID
5-816-199 ppp Connect Timer
5-816-200 Manual Polling
5-816-201 Regist Status
CTL [- / - / -]
CTL [- / - / -]
CTL [0 or 1/ 0 / 1]
0: Disable
1: Enable
CTL [0 to 0 / 0 / 0]
CTL [15 to 30 / 15 / 1min/step]
CTL [- / - / -]
[Execute]
CTL [0 to 4 / 0 / 1]
[Execute]
Displays the installation status as the target of NRS services.
0 Not installed as NRS machines or Cumin.
1
2
Installing as Cumin. Box enrollment has completed. Unable to response for the machine searching from Basil at this status.
Installation has completed. Unable to response for the machine searching from
Basil at this status.
3
4
As a NRS machine, installation has completed. It cannot install as Cumin.
NRS modules is not being launched.
5-816-202 Letter Number
5-816-203 Confirm Execute
*CTL [- / - / -]
*CTL [- / - / -]
[Execute]
Controller SP Tables - SP5000
5-816-204 Confirm Result
Displays the result of SP5-816-203.
CTL [0 to 255 / 0 / 1]
0: Success Inquiry
1: Request number error
3: Communication error (Enabled
Proxy)
4: Communication error (Disabled
Proxy)
5: Proxy error (failed auth.)
6: Communication error
8: Other error (See SP5-816-208 for detail)
9: Processing inquiry
20: Failed Dial-up auth.
21: Failed answer tone detection
22: Failed career detection
23: Invalid modem value
24: Shortage of electrical current
25: Cable disconnected
26: Line occupied
535
536
4. Controller SP Mode Tables
5-816-205 Confirm Place CTL [0 to 255 / 0 / 1]
0: Success registration
1: Request number error
3: Communication error (Enabled
Proxy)
4: Communication error (Disabled
Proxy)
5: Proxy error (failed auth.)
6: Communication error
8: Other error (See SP5-816-208 for detail)
9: Processing registration
20: Failed Dial-up auth.
21: Failed answer tone detection
22: Failed career detection
23: Invalid modem value
24: Shortage of electrical current
25: Cable disconnected
26: Line occupied
Displays the installed section informed from G/W for response of request number inquiry if the section is enrolled on the G/W.
5-816-206 Register Execute CTL [- / - / -]
[Execute]
Executes the registration of Cumin.
5-816-207 Register Result CTL [0 to 255 / 0 / 1]
Displays the registration result. Shows the executed status of SP5-816-206.
5-816-208 Error Code CTL [-2147483647 to 2147483647 /
0 / -]
Displays the registration result of SP5-816-204.
Controller SP Tables - SP5000
5-816-208 Invalid modem parameter
-11001 Chat parameter error.
-11002 Chat execution error.
-11003 Unexpected error
-11004 Disconnect operation occurred during modem communication,
-11005 NCS reboot occurred during modem communication.
5-816-208 Errors with invalid procedure or settings
-12002 Attempted to inquiry or registration without obtaining the installation status.
-12003 Attempted to registrate without inquiry despite un-registered status.
-12004 Attempted to install with invalid certification, ID2, and without input the machine number.
-12005 Executed inquiry/ registration in a invalid Cumin function and prohibited
@Remote communication.
5-816-208 -12006 Attempted to inquiry in BOX registration completed.
-12007 Registration attempted with the different request number from the number used for the last inquiry.
-12008 Certification update failed because Job processing etc.
-12009 Mismatched between ID2 in NR-RAM and ID2 in the individual certification.
-12010 Not initialized the certification area.
5-816-208 Error with error response from G/W
-2385 Inappropriate international dialing prefix
-2387 Not supported in the center.
-2389 DB failure
-2390 Program failure
-2391 Double registration of the machine
537
538
4. Controller SP Mode Tables
5-816-208 -2392 Parameter error
-2393 Not managed Basil
-2394 Not managed machine
-2395 Invalid BOX ID of Basil
-2396 Invalid Device ID of Basil
-2397 Different format of ID2 (includes invalid ID2)
-2398 Different format of request number
5-816-209 Instl Clear
5-816-240 CommErrorTime
5-816-241 CommErrorCode 1
5-816-242 CommErrorCode 2
5-816-243 CommErrorCode 3
5-816-244 CommErrorState 1
5-816-245 CommErrorState 2
5-816-246 CommErrorState 3
5-816-247 SSL Error Count
5-816-248 Other Error Count
5-816-250 Commlog Print
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
[0 or 1 / 0 / 1]
[0 to 0 / 0 / 1]
[0 to 0xffffffff / 0x00000000 / 1]
[0 to 0xffffffff / 0x00000000 / 1]
[0 to 0xffffffff / 0x00000000 / 1]
[0 to 0xffff / 0x0000 / 1]
[0 to 0xffff / 0x0000 / 1]
[0 to 0xffff / 0x0000 / 1]
[0 to 255 / 0 / 1]
[0 to 255 / 0 / 1]
[0 to 255 / 0 / 1]
5821 [Remote Service RCG Setting]
5-821-002 RCG IP Address
5-821-003 RCG Port Number
5-821-004 RCG IPv4 URL Path
5-821-005 RCG IPv6 Address
5-821-006 RCG IPv6 URL Path
*CTL [00000000h to FFFFFFFFh /
00000000h / 1]
*CTL [0 to 65535 / 443 / 1]
*CTL [0 to 0 / 0 / 0]
*CTL [0 to 0 / 0 / 0]
*CTL [0 to 0 / 0 / 0]
Controller SP Tables - SP5000
5-821-007 RCG Host Name
5-821-008 RCG Host URL Path
5824
5-824-001
[NV-RAM Data Upload]
*CTL
*CTL
[0 to 0 / 0 / 0]
[0 to 0 / 0 / 0]
CTL [- / - / -]
[Execute]
5825
5-825-001
[NV-RAM Data Download]
CTL [- / - / -]
[Execute]
5828 [Network Setting]
5-828-039 User Class
5-828-040 Class Id
5-828-050 1284 Compatibility (Centro)
5-828-052 ECP (Centro)
CTL
CTL
*CTL
*CTL
[0 to 0 / 0 / 0]
[0 to 0 / 0 / 0]
[0 or 1 / 1 / 1]
0: Disabled
1: Enabled
[0 or 1 / 1 / 1]
0: Disabled
1: Enabled
Enables or disables ECP Compatibility.
5-828-065 Job Spooling *CTL
5-828-066 Job Spooling Clear: Start Time *CTL
[0 or 1 / 0 / 1]
0: Disabled
1: Enabled
[0 or 1 / 1 / 1]
0: ON (Data is cleared)
1: OFF (Automatically printed)
539
540
4. Controller SP Mode Tables
5-828-069 Job Spooling (Protocol)
5-828-091 Web (0: OFF 1: ON)
*CTL [0 or 1 / 0 / 1]
0: Validates
1: Invalidates bit0: LPR bit1: FTP bit2: IPP bit3: SMB bit4: BMLinkS bit5: DIPRINT bit6: sftp bit7: (Reserved)
* CTL [0 or 1 / 0x00000000 / 1bit] 5-828-087 Protocol usage
Shows which protocols have been used with the network.
0: Off (Not used the network with the protocol.)
1: On (Used the network with the protocol once or more.) bit0: IPsec, bit1: IPv6, bit2: IEEE 802. 1X, bit3:Wireless LAN, bit4: Security mode level setting, bit5:Appletalk, bit6: DHCP, bit7: DHCPv6, bit8: telnet, bit9: SSL, bit10: HTTPS, bit11: BMLinkS printing, bit12: diprint printing, bit13: LPR printing, bit14: ftp printing, bit15: rsh printing, bit16: SMB printing, bit17: WSD-Printer, bit18: WSD-Scanner, bit19: Scan to SMB, bit20: Scan to NCP, bit21: Reserve, bit22: Bluetooth, bit23: IEEE 1284, bit24: USB printing, bit25: Dynamic DNS, bit26: Netware printing, bit27: LLTD, bit28: IPP printing, bit29: IPP printing (SSL), bit30: ssh, bit31: sftp
5-828-090 TELNET (0: OFF 1: ON) * CTL [0 or 1 / 1 / 1]
0: Disable
1: Enable
* CTL [0 or 1 / 1 / 1]
0: Disable
1: Enable
Controller SP Tables - SP5000
5-828-145 Active IPv6 Link Local Address
5-828-147 Active IPv6 Stateless Address 1
5-828-149 Active IPv6 Stateless Address 2
5-828-151 Active IPv6 Stateless Address 3
5-828-153 Active IPv6 Stateless Address 4
5-828-155 Active IPv6 Stateless Address 5
5-828-156 IPv6 Manual Address
5-828-158 IPv6 Gateway Address
CTL
CTL
CTL
CTL
CTL
CTL
*CTL
*CTL
[- / - / -]
[0000000000000000000000000
00000000000h to
FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF8
0h /
00000000000000000000000000
00000040h / -]
These SPs are the IPv6 status addresses (1 to 5) referenced on the
Ethernet or wireless LAN (802.11b) in the format:
"Status Address" + "Prefix Length"
The IPv6 address consists of a total
128 bits configured in 8 blocks of 16 bits each.
[0000000000000000000000000
00000000000h to
FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF8
0h /
00000000000000000000000000
00000040h / -]
These SPs are the IPv6 status addresses (1 to 5) referenced on the
Ethernet or wireless LAN (802.11b) in the format:
"Status Address" + "Prefix Length"
The IPv6 address consists of a total
128 bits configured in 8 blocks of 16 bits each.
[0000000000000000000000000
0000000h to
FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFh
/
00000000000000000000000000
000000h / -]
541
542
4. Controller SP Mode Tables
5-828-161 IPv6 Stateless Auto Setting
5-828-219 IPsec Aggressive Mode Setting
5-828-236 Web Item visible
*CTL
CTL
*CTL
[0 or 1 / 1 / 1]
0: Disable
1: Enable
[0 or 1 / 0 / 1]
[0x0000 to 0xffff / 0xffff / -]
Displays or does not display the Web system items.
bit0: Net RICOH bit1: Consumable Supplier bit2-15: Reserved (all)
5-828-237 Web shopping link visible *CTL
5-828-238 Web supplies Link visible *CTL
[0 or 1 / 1 / 1]
0: Not display
1:Display
[Up to 31char / URL1 / 1]
0: Not display
1: Display
5-828-239 Web Link1 Name
5-828-240 Web Link1 URL
5-828-241 Web Link1 visible
5-828-242 Web Link2 Name
5-828-243 Web Link2 URL
5-828-244 Web Link2 visible
5-828-249 DHCPv6 DUID
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
CTL
[Up to 31char / URL1 / 1]
[Up to 127char / URL1 / 1]
[Up to 31 char / URL2/ -]
0: Not display
1: Display
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
5832 [HDD]
5-832-001 HDD Formatting (ALL) CTL [- / - / -]
[Execute]
Controller SP Tables - SP5000
5-832-002 HDD Formatting (IMH)
5-832-003 HDD Formatting (Thumbnail)
5-832-004 HDD Formatting (Job Log)
5-832-005 HDD Formatting (Printer Fonts)
5-832-006 HDD Formatting (User Info1)
5-832-007 Mail RX Data
5-832-008 Mail TX Data
5-832-009 HDD Formatting (Data for a
Design)
5-832-010 HDD Formatting (Log)
5-832-011 HDD Formatting (Ridoc I/F)
5-832-012 HDD Formatting (Thumbnail)
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
5836 [Capture Setting]
5-836-001 Capture Function (0:Off 1:On)
5-836-011 Capture Setting: Copy
5-836-012 Capture Setting: Doc. Svr.
* CTL [0 or 1 / 0 / 1]
0: Disable
1: Enable
* CTL [0 or 1 / 0 / 1]
* CTL [0 or 1 / 0 / 1]
543
544
4. Controller SP Mode Tables
5-836-013 Capture Setting: Fax RX Printer
5-836-014 Capture Setting: Fax TX
5-836-015 Capture Setting: Printer
* CTL [0 or 1 / 0 / 1]
* CTL [0 or 1 / 0 / 1]
* CTL [0 or 1 / 0 / 1]
5-836-016 Capture Setting: Scanner
5-836-017 Capture Setting: SDK
* CTL
* CTL
[0 or 1 / 0 / 1]
[0 or 1 / 0 / 1]
5-836-061 Captured File Resend (0:Off 1:On) * CTL [0 or 1 / 1 / 1]
5836 [Capture Setting]
5-836-071 Reduction for Copy Color
5-836-072 Reduction for Copy B&W Text
5-836-073 Reduction for Copy B&W Other
5-836-074 Reduction for Printer Color
*CTL [0 to 3 / 2 / 1]
0: 1to-1
1: 1/2
2: 1/3
3: 1/4
*CTL [0 to 3, 6 / 0 / 1]
0: 1to-1
1: 1/2
2: 1/3
3: 1/4
6: 2/3
*CTL [0 to 3, 6 / 0 / 1]
0: 1to-1
1: 1/2
2: 1/3
3: 1/4
6: 2/3
*CTL [0 to 3 / 2 / 1]
0: 1to-1
1: 1/2
2: 1/3
3: 1/4
5-836-075 Reduction for Printer B&W
5-836-077 Reduction for Printer Color
1200dpi
5-836-078 Reduction for Printer B&W
1200dpi
5-836-081 Format for Copy Color
5-836-082 Format for Copy B&W Text
Controller SP Tables - SP5000
*CTL [0 to 3, 6 / 0 / 1]
0: 1to-1
1: 1/2
2: 1/3
3: 1/4
6: 2/3
*CTL [1, 3 to 5 / 4 / 1]
1:1/2
3:1/4
4:1/6
5:1/8
*CTL [0 to 5 / 1 / 1]
0: 1
1: 1/2
2: 1/3
3: 1/4
4: 1/6
5: 1/8
*CTL [0 / 0 / 1]
0: JFIF/JPEG
1: TIFF/MMR
2: TIFF/MH
3: TIFF/MR
*CTL [ 0 to 3 / 1 / 1]
0: JFIF/JPEG
1: TIFF/MMR
2: TIFF/MH
3: TIFF/MR
545
546
4. Controller SP Mode Tables
5-836-083 Format for Copy B&W Other
5-836-084 Format for Printer Color
5-836-085 Format for Printer B&W
5-836-091 Default for JPEG
5-836-101 Primary srv IP address
5-836-102 Primary srv scheme
5-836-103 Primary srv port number
5-836-104 Primary srv URL path
5-836-111 Secondary srv IP address
5-836-112 Secondary srv scheme
5-836-113 Secondary srv port number
5-836-114 Secondary srv URL path
5-836-120 Default Reso Rate Switch
*CTL [ 0 to 3 / 1 / 1]
0: JFIF/JPEG
1: TIFF/MMR
2: TIFF/MH
3: TIFF/MR
*CTL [0 / 0 / 1]
*CTL [ 0 to 3 / 1 / 1]
0: JFIF/JPEG
1: TIFF/MMR
2: TIFF/MH
3: TIFF/MR
*CTL [5 to 95 / 50 / 1]
*CTL [000.000.000.000 to
255.255.255.255 / - / 1]
*CTL [0 to 6 char / NULL / -]
*CTL [1 to 65535 / 80 / 1]
*CTL [0 to 16 char / - / 1]
*CTL [000.000.000.000 to
255.255.255.255 / - / 1]
*CTL [0 to 6 char / NULL / -]
*CTL [1 to 65535 / 80 / 1]
*CTL [0 to 16 char / - / 1]
*CTL [0 or 1 / 0 / 1]
5-836-121 Reso Copy(Color)
5-836-122 Reso: Copy(Mono)
5-836-123 Reso Print(Color)
5-836-124 Reso: Print(Mono)
Controller SP Tables - SP5000
*CTL [0 to 255 / 2 / 1]
0:600DPi
1:400DPi
2:300DPi
3:200DPi
4:150DPi
5:100DPi
6:75DPi
*CTL [0 to 255 / 3 / 1]
0: 600dpi/
1: 400dpi/
2: 300dpi/
3: 200dpi/
4: 150dpi/
5: 100dpi/
6: 75dpi
*CTL [0 to 255 / 2 / 1]
0:600DPi
1:400DPi
2:300DPi
3:200DPi
4:150DPi
5:100DPi
6:75DPi
*CTL [0 to 255 / 3 / 1]
0:600DPi
1:400DPi
2:300DPi
3:200DPi
4:150DPi
5:100DPi
6:75DPi
547
548
4. Controller SP Mode Tables
5-836-125 Reso: Fax(Color)
5-836-126 Reso: Fax(Mono)
5-836-127 Reso: Scanner(Color)
5-836-128 Reso: Scanner(Mono)
*CTL [0 to 255 / 4 / 1]
0:600DPi
1:400DPi
2:300DPi
3:200DPi
4:150DPi
5:100DPi
6:75DPi
*CTL [0 to 255 / 3 / 1]
0:600DPi
1:400DPi
2:300DPi
3:200DPi
4:150DPi
5:100DPi
6:75DPi
*CTL [0 to 255 / 4 / 1]
0:600DPi
1:400DPi
2:300DPi
3:200DPi
4:150DPi
5:100DPi
6:75DPi
*CTL [0 to 255 / 3 / 1]
0:600DPi
1:400DPi
2:300DPi
3:200DPi
4:150DPi
5:100DPi
6:75DPi
5-836-129 Reso: SDK(Color)
5-836-130 Reso: SDK(Mono)
5-836-141 All Addr Info Switch
5-836-142 Stand-by Doc Max Number
5-836-143 ClearLightPDF Switch
5840 [IEEE 802.11]
5-840-006 Channel Max
5841
DFU
5-840-007 Channel Min
DFU
5-840-011 WEP key Select
5-840-045 WPA Debug Lvl
5-840-046 11w
5-840-047 PSK Set Type
[Supply Name Setting]
*CTL
*CTL
Controller SP Tables - SP5000
[0 to 255 / 4 / 1]
*CTL [0 to 255 / 3 / 1]
*CTL [0 or 1 / 1 / 1]
*CTL [10 to 10000 / 2000 / 1]
[0 or 1 / 0 / 1]
*CTL [1 to 11 or 13 / 11 or 13 / 1 ]
Europe/Asia: 1 to 13
NA/ Asia: 1 to 11
*CTL [1 to 11 or 13 / 1 / 1]
Europe: 1 to 13
NA/ Asia: 1 to 11
*CTL [00 to 11 / 00 / 1binary]
00: Key #1
01: Key #2 (Reserved)
10: Key #3 (Reserved)
11: Key #4 (Reserved)
*CTL [1 to 3 / 3 / 1]
1: Info
2: wArning
3: error
*CTL [0 to 2 / 0 / 1]
*CTL [0 or 1 / 0 / 1]
549
550
4. Controller SP Mode Tables
5-841-001 Toner Name Setting:Black
5-841-002 Toner Name Setting:Cyan
5-841-003 Toner Name Setting:Yellow
5-841-004 Toner Name Setting:Magenta
5-841-007 OrgStamp
5-841-009 WasteTonerBottle
5-841-011 Staple Std1
5-841-012 Staple Std2
5-841-013 Staple Std3
5-841-014 Staple Std4
5-841-021 Staple Bind 1
5-841-022 Staple Bind 2
5-841-023 Staple Bind 3
*CTL Specifies supply names. These appear on the screen when the user presses the
*CTL
Inquiry button in the user tools screen.
*CTL [0 to 20 / NULL / 1byte]
*CTL
*CTL
*CTL [0 to 20 / NULL / 1byte]
*CTL Specifies supply names. These appear
*CTL on the screen when the user presses the
Inquiry button in the user tools screen.
*CTL
[0 to 20 / NULL / 1byte]
*CTL
*CTL
*CTL Specifies supply names. These appear on the screen when the user presses the
*CTL
Inquiry button in the user tools screen.
[0 to 20 / NULL / 1byte]
5842 [GWWS Analysis]
Controller SP Tables - SP5000
5-842-001 Setting 1 *CTL [8bit assign / 00000000 / bit switch]
0bit[LSB]: system, other group
1bit: capture related group
2bit: authentication related group
3bit: address book related group
4bit: device management related group
5bit: output related(print, FAX, and delivery) group
6bit: repository, F0,etc. document related group
7bit: debug log level suppression
Default: 00000000 – do not change
Netfiles: Jobs to be printed from the document server using a PC and the
DeskTopBinder software
5-842-002 Setting 2 *CTL [8bit assign / 00000000 / bit switch]
0~6bit: unused
7bit: time stamp setting for 5682mmesg log.
(1: min./sec/msec, 0: day/hour/min./ sec)
5844 [USB]
5-844-001 Transfer Rate *CTL [1 to 4 / 0x04 / -]
0x01: Full speed
0x04: Auto Change
*CTL [- / - / -] 5-844-002 Vendor ID
DFU
5-844-003 Product ID
DFU
5-844-004 Device Release Number
DFU
*CTL
*CTL
[- / - / -]
[- / - / -]
551
552
4. Controller SP Mode Tables
5-844-005 Fixed USB Port
5-844-006 PnP Model Name
5-844-007 PnP Serial Number
5-844-008 Mac Supply Level
5-844-100 Notify Unsupport
5845 [Delivery Server Setting]
5-845-001 FTP Port No.
5-845-002 IP Address (Primary)
5-845-006 Delivery Error Display Time
5-845-008 IP Address (Secondary)
5-845-009 Delivery Server Model
*CTL [0 to 2 / 0 / 1]
*CTL [0 to 0 / 0 / 0]
*CTL [0 to 0 / 0 / 0]
*CTL [0 or 1 / 1 / 1]
*CTL [0 or 1 / 1 / 1]
*CTL [0 to 65535 / 3670 / 1]
*CTL [000.000.000.000 to
255.255.255.255 /
000.000.000.000 / -]
*CTL [0 to 999 / 300 / 1 second ]
*CTL [000.000.000.000 to
255.255.255.255 /
000.000.000.000 / -]
*CTL [0 to 4 / 0 / 1 ]
0: Unknown
1: SG1 Provided
2: SG1 Package
3: SG2 Provided
4: SG2 Package
Controller SP Tables - SP5000
5-845-010 Delivery Svr. Capability *CTL [0 to 255 / - / 1]
Bit7 1 Comment information exits
Bit6 1 Direct specification of mail address possible
Bit5 1 Mail RX confirmation setting possible
Bit4 1 Address book automatic update function exists
Bit3 1 Fax RX delivery function exists
Bit2 1 Sender password function exists
Bit1 1 Function to link MK-1 user and Sender exists
Bit0 1 Sender specification required (if set to 1, Bit6 is set to “0”)
5-845-011 Delivery Svr Capability (Ext) *CTL [0 to 255 / - / 1 ]
Bit7 = 1 Address book usage limitation (Limitation for each authorized user)
Bit6 = 1 RDH authorization link
Bit5 to 0: Not used
5-845-013 Server Scheme (Primary)
5-845-014 Server Port Number (Primary)
*CTL [ Up to 6 char / - / -]
*CTL [ - / - / -]
5-845-015 Server URL Path (Primary)
5-845-016 Server Scheme (Secondary)
*CTL [ - / - / -]
*CTL [ Up to 6 char / - / -]
5-845-017 Server Port Number (Secondary) *CTL [1 to 65535 / 80 / 1]
5-845-018 Server URL Path (Secondary)
5-845-022 Rapid Sending Control
*CTL [ Up to 16 byte / - / -]
*CTL [0 or 1 / 1 / -]
0: Control disabled
1: Control enabled
5846 [UCS Setting]
5-846-001 Machine ID (for Delivery Server) *CTL [- / - / -]
5-846-002 Machine ID Clear(for Delivery
Server)
*CTL [- / - / -]
[Execute]
553
554
4. Controller SP Mode Tables
5-846-003 Maximum Entries
5-846-006 Delivery Server Retry Timer
5-846-007 Delivery Server Retry Times
5-846-008 Delivery Server Maximum Entries *CTL [2000 to 20000 / 2000 / 1]
5-846-010 LDAP Search Timeout *CTL [1 to 255 / 60 / 1]
5-846-020 WSD Maximum Entries
5-846-021 Folder Auth Change
5-846-040 Addr Book Migration(USB-
>HDD)
5-846-041 Fill Addr Acl Info
5-846-043 Addr Book Media
*CTL [50 to 250 / 250 / 1]
*CTL [0 or 1 / 0 / 1]
0: Login User, 1: Destination
*CTL [- / - / -]
[Execute]
*CTL [- / - / -]
[Execute]
*CTL [0 to 30 / 0 /1]
0: Unconfirmed
1: SD Slot 1
2: SD Slot 2
3: SD Slot 3
4: USB Flash ROM
10: SD Slot 10
20: HDD
30: Nothing
5-846-047 Initialize Local Address Book
*CTL [2000 to 20000 / 2000 / 1]
*CTL [0 to 255 / 0 / 1]
*CTL [0 to 255 / 0 / 1]
5-846-048 Initialize Delivery Addr Book
5-846-049 Initialize LDAP Addr Book
5-846-050 Initialize All Addr Book
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
Controller SP Tables - SP5000
5-846-051 Backup All Addr Book
5-846-052 Restore All Addr Book
CTL [- / - / -]
[Execute]
CTL [- / - / -]
[Execute]
5-846-053 Clear Backup Info CTL [- / - / -]
[Execute]
*CTL [0x00 to 0xff / 0x0f/ 1] 5-846-060 Search Option
This SP uses bit switches to set up the fuzzy search options for the UCS local address book.
Bit: Meaning
0: Checks both upper/lower case characters
1: Japan Only
2: Japan Only
3: Japan Only
4 to 7: Not Used
5-846-062 Complexity Option 1
5-846-063 Complexity Option 2
5-846-064 Complexity Option 3
5-846-065 Complexity Option 4
5-846-091 FTP Auth Port Setting
5-846-094 Encryption Stat
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[0 to 32 / 0 / 1]
[0 to 32 / 0 / 1]
[0 to 32 / 0 / 1]
[0 to 32 / 0 / 1]
[0 to 65535 / 3671 / 1]
[0 to 255 / - / 1]
5847 [Rep Resolution Reduction]
5-847-001 Rate for Copy Color *CTL [ 0 to 5 / 2 / 1 ]
0: 1x
1: 1/2x
2: 1/3x
3: 1/4x
4: 1/6x
5: 1/8x
555
556
4. Controller SP Mode Tables
5-847-002 Rate for Copy B&W Text
5-847-003 Rate for Copy B&W Other
5-847-004 Rate for Printer Color
5-847-005 Rate for Printer B&W
5-847-006 Rate for Printer Color 1200dpi
*CTL [ 0 to 6 / 0 / 1 ]
*CTL
0: 1x
1: 1/2x
2: 1/3x
3: 1/4x
4: 1/6x
5: 1/8x
6: 2/3x
*CTL [ 0 to 5 / 2 / 1 ]
0: 1x
1: 1/2x
2: 1/3x
3: 1/4x
4: 1/6x
5: 1/8x
*CTL [ 0 to 6 / 0 / 1 ]
0: 1x
1: 1/2x
2: 1/3x
3: 1/4x
4: 1/6x
5: 1/8x
6: 2/3x
*CTL [ 0 to 5 / 4 / 1 ]
0: 1x
1: 1/2x
2: 1/3x
3: 1/4x
4: 1/6x
5: 1/8x
Controller SP Tables - SP5000
5-847-007 Rate for Printer B&W 1200dpi *CTL [ 0 to 6 / 1 / 1 ]
0: 1x
1: 1/2x
2: 1/3x
3: 1/4x
4: 1/6x
5: 1/8x
6: 2/3x
*CTL [5 to 95 / 50 / 1 ] 5-847-021 Network Quality Default for
JPEG
5848 [Web Service]
5-848-002 Access Ctrl: Repository (only
Lower 4 bits)
5-848-003 Access Control: Doc. Svr. Print
(Lower 4 bits)
5-848-004 Access Control: udirectory
(Lower 4 bits)
5-848-007 Access Ctrl: Comm. Log Fax
(Lower 4 bits)
*CTL [- / - / -]
0000: No access control
0001: Denies access to DeskTop
Binder.
0010: No writing control
*CTL [- / - / -]
0000: No access control
0001: Denies access to DeskTop
Binder.
*CTL [- / - / -]
0000: No access control
0001: Denies access to DeskTop
Binder.
*CTL [- / - / -]
0000: No access control
0001: Denies access to DeskTop
Binder.
557
558
4. Controller SP Mode Tables
5-848-009 Access Ctrl: Job Ctrl (Lower 4 bits)
5-848-011 Access Ctrl:
Devicemanagement (Lower
4bits)
5-848-021 Access Ctrl: Delivery (Lower 4 bits)
5-848-022 Access Ctrl: uadministration
(Lower 4bits)
5-848-024 Access Ctrl: Log Service (Lower
4bits)
5-848-025 Access Ctrl: Rest WebService
(Lower 4bits)
*CTL [- / - / -]
0000: No access control
0001: Denies access to DeskTop
Binder.
*CTL [- / - / -]
0000: No access control
0001: Denies access to DeskTop
Binder.
*CTL [- / - / -]
0000: No access control
0001: Denies access to DeskTop
Binder.
*CTL [- / - / -]
0000: No access control
0001: Denies access to DeskTop
Binder.
*CTL [- / - / -]
0000: No access control
0001: Denies access to DeskTop
Binder.
*CTL [- / - / -]
0000: No access control
0001: Denies access to DeskTop
Binder.
*CTL DFU 5-848-099 Repository: Download Image
Setting
5-848-100 Repository: Download Image
Max. Size
5-848-150 Log Operation Mode
5-848-217 Setting: Timing
*CTL
*CTL
*CTL
[1 to 2048 / 2048 / 1 MB/step]
[0 to 9 / 0 / 1]
NIA
5849 [Installation Date]
Controller SP Tables - SP5000
5-849-001 Display
5-849-002 Switch to Print
*CTL [- / - / -]
*CTL [0 or 1 / 1 / 1 ]
0: OFF (No Print)
1: ON (Print)
*CTL [0 to 99999999 / 0 / 1] 5-849-003 Setup Count
5850 [Address Book Function]
5-850-003 Replacement of Circuit
Classifications
*CTL [0 to 13 / 1 / 1]
1: G3
2: EXT
3: G3-1
4: G3-1- EXT
5: G3-2
6: G3-2- EXT
7: G3-3
8: G3-3-EXT
9: G3-idle-EXT
10: idle-EXT
11: I-G3
12: I-G3-EXT
13: G4
5851 [Bluetooth]
5-851-001 mode *CTL [0 or 1 / 0 / 1]
5853
5-853-001 -
[Stamp Date Download]
5856
CTL [- / - / -]
[Remote ROM Update]
Allows the technician to upgrade the firmware using a local port (IEEE1284) when updating the remote ROM.
559
4. Controller SP Mode Tables
560
5-856-002 Local Port *CTL [0 or 1 / 0 / 1]
0: Disable
1: Enable
5858 [Collect Machine Info]
5-858-001 0:OFF 1:ON
5-858-002 Save To (0:HDD 1:SD)
5-858-003 Make Log Trace Dir
5-858-101 Failure Occuring Date
5-858-102 Tracing Days
5-858-103 Acquire Fax Address(0:OFF
1:ON)
5-858-111 Acquire All Info & Logs
5-858-121 Acquire Configuration Page
5-858-122 Acquire Font Page
5-858-123 Acquire Print Setting List
5-858-124 Acquire Error Log
5-858-131 Acquire Fax Info
5-858-141 Acquire All Debug Logs
5-858-142 Acquire Controller Debug Logs
Only
5-858-143 Acquire Engine Debug Logs
Only
5-858-144 Acquire Opepanel Debug Logs
Only
5-858-145 Acquire FCU Debug Logs Only
5860 [SMTP/POP3/IMAP4]
5-860-020 Partial Mail Receive Timeout
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
[0 or 1 / 1 / 1]
[0 or 1 / 0 / 1]
[0 or 1 / 0 / 0]
[0 to 20371212 / 0 / 1]
[1 to 180 / 2 / 1day/step]
[0 or 1 / 0 / 1]
[0 or 1 / 0 / 0]
[0 or 1 / 0 / 0]
[0 or 1 / 0 / 0]
[0 or 1 / 0 / 0]
[0 or 1 / 0 / 0]
[0 or 1 / 0 / 0]
[0 or 1 / 0 / 0]
[0 or 1 / 0 / 0]
[0 or 1 / 0 / 0]
[0 or 1 / 0 / 0]
[0 or 1 / 0 / 0]
*CTL [1 to 168 / 72 / 1hour/step]
Controller SP Tables - SP5000
5-860-021 MDN Response RFC2298
Compliance
*CTL [0 or 1 / 1 / 1]
0: No
1: Yes
5-860-022 SMTP Auth. From Field
Replacement
*CTL [0 to 1 / 0 / 1]
0: No. “From” item not switched.
1: Yes. “From item switched.
*CTL [0 to 255 / 0 / - ] 5-860-025 SMTP Auth. Direct Setting
Selects the authentication method for SMPT.
Bit switch:
Bit 0: LOGIN
Bit 1: PLAIN
Bit 2: CRAM MD5
Bit 3: DIGEST MD5
Bit 4 to 7: Not used
• This SP is activated only when SMTP authorization is enabled by UP mode.
5-860-026 S/MIME:MIME Header Setting *CTL [0 to 2 / 0 / 1]
0: Microsoft Outlook Express standard
1: Internet Draft standard
2: RFC standard
5-860-028 S/MIME: Authentication Check *CTL [0 or 1 / 0 / 1]
0: No (not check)
1: Yes (check)
5866 [Email Report]
5-866-001 Report Validity
5-866-005 Add Date Field
CTL
CTL
[0 or 1 / 0 / 1]
0: Enabled
1: Disabled
[0 or 1 / 0 / 1]
0: Enabled
1: Disabled
561
562
4. Controller SP Mode Tables
5-866-110 CounterE-Mail:Validity
5-866-111 CounterE-Mail:Destination
Registration
5-866-112 CounterE-Mail:Send Test
5-866-113 CounterE-Mail:Next Send Date
5-866-114 CounterE-Mail:Send Date Setting
5-866-115 CounterE-Mail:Send Time Setting
5-866-121 CounterE-Mail:Destination1
5-866-122 CounterE-Mail:Destination2
5-866-123 CounterE-Mail:Destination3
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
[0 or 1 / 0 / 1]
[0 to 0 / 0 / 0]
[0 to 0 / 0 / 0]
[0 to 0 / 0 / 0]
[0 to 31 / 0 / 1]
[0 to 2359 / 0 / 1]
[0 to 0 / 0 / 0]
[0 to 0 / 0 / 0]
[0 to 0 / 0 / 0]
5870 [Common Key Info Writing]
5-870-001 Writing CTL
5-870-003 Initialize
5-870-004 Writing: 2048bit
CTL
CTL
[- / - / -]
[Execute]
[- / - / -]
[Execute]
[- / - / -]
[Execute]
5873 [SD Card Appli Move]
5-873-001 Move Exec CTL
5-873-002 Undo Exec CTL
[- / - / -]
[Execute]
[- / - / -]
[Execute]
5875 [SC Auto Reboot]
5-875-001 Reboot Setting * CTL [0 or 1 / 0 / 1]
Controller SP Tables - SP5000
5-875-002 Reboot Type *CTL [0 or 1 / 0 / 1]
0: Manual reboot
1: Automatic reboot
5878 [Option Setup]
5-878-001 Data Overwrite Security
5-878-002 HDD Encryption
5-878-004 OCR Dictionary
CTL
CTL
CTL
[- / - / -]
[Execute]
[- / - / -]
[Execute]
[- / - / -]
[Execute]
5881 [Fixed Phrase Block Erasing]
5-881-001 -
Delete the fixed phrase.
CTL [- / - / -]
5885 [Set WIM Function] Web Image Monitor Settings
5-885-020 DocSvr Acc Ctrl *CTL [0 or 1 / 0 / 1]
0: OFF
1: ON
Bit Meaning
0: Forbid all document server access
(1)
1: Forbid user mode access (1)
2: Forbid print function (1)
3: Forbid fax TX (1)
4: Forbid scan sending (1)
5: Forbid downloading (1)
6: Forbid delete (1)
7: Reserved
563
564
4. Controller SP Mode Tables
5-885-050 DocSvr Format
5-885-051 DocSvr Trans
5-885-100 Set Signature
5-885-101 Set Encrypsion
5-885-200 DocSvr Timeout
5886 [Farm Update Setting]
5-886-100 Skip Version Check
5-886-101 Skip LR Check
5-886-111 Auto Update Setting
5-886-112 Auto Update Prohibit Term Setting
5-886-113 Auto Update Prohibit Start hour
5-886-114 Auto Update Prohibit End hour
5-886-115 SFU Auto Download Setting
5-886-116 Auto Update Next Date
5-886-117 Auto Update Retry Interval Hour
5-886-119 Auto Update @Remote Using
Setting
5-886-120 Auto Update Prohibit Day of Week
Setting
5-886-151 Permit SubId Update
5-886-201 Restore Date
*CTL [0 to 2 / 0 / 1]
0: Thumbnail, 1: Icon, 2: Details
*CTL [ 5 to 20 / 10 / 1]
*CTL [0 to 2 / 0 / 1]
0: Setting for each e-mail
1: Signature for all
2: No signature
*CTL [0 to 1 / 0 / 1]
0: Not encrypted
1: Encryption
*CTL Not Used
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
[0 or 1 / 0 / 1]
[0 or 1 / 0 / 1]
[0 or 1 / 0 / 1]
[0 or 1 / 1 / 1]
[0 to 23 / 9 / 1hour/step]
[0 to 23 / 17 / 1hour/step]
[0 or 1 / 0 / 1]
[0 to 0 / 0 / 0]
[1 to 24 / 1 / 1hour/step]
[0 or 1 / 0 / 1]
[0 to 255 / 0 / 1]
[0 or 1 / 0 / 1]
[0 to 0 / 0 / 0]
Controller SP Tables - SP5000
5-886-202 Save Old Version List
5887
5-887-001 -
[SD GetCounter]
CTL [- / - / -]
[Execute]
5888
5-888-001 -
[Personal Information Protect]
*CTL [0 or 1 / 0 / 1]
Selects the protection level for logs.
0: No authentication, No protection for logs
1: No authentication, Protected logs (only an administrator can see the logs)
5893 [SDK Apli Cnt Name]
5-893-001 SDK-1
CTL [0 to 0 / 0 / 0]
5-893-002 SDK-2
5-893-003 SDK-3
5-893-004 SDK-4
5-893-005 SDK-5
5-893-006 SDK-6
5-893-007 SDK-7
5-893-008 SDK-8
CTL [- / - / -]
[Display text]
CTL [- / - / -]
[Display text]
CTL [- / - / -]
[Display text]
CTL [- / - / -]
[Display text]
CTL [- / - / -]
[Display text]
CTL [- / - / -]
[Display text]
CTL [- / - / -]
[Display text]
CTL [- / - / -]
[Display text]
565
566
4. Controller SP Mode Tables
5-893-009 SDK-9
5-893-010 SDK-10
5-893-011 SDK-11
5-893-012 SDK-12
CTL [- / - / -]
[Display text]
CTL [- / - / -]
[Display text]
CTL [- / - / -]
[Display text]
CTL [- / - / -]
[Display text]
5895 [Application invalidation]
5-895-001 Printer
5-895-002 Scanner
CTL
CTL
[- / - / -]
[- / - / -]
5907
5-907-001
[Plug & Play Maker/Model Name]
*CTL [- / - / -]
5913 [Switchover Permission Time]
5-913-002 Print Application Timer *CTL [3 to 30, immediate / 3 / 1sec/ step]
5967 [Copy Server: Set Function]
5-967-001 (0: ON 1: OFF) *CTL [0 or 1 / 0 / 1]
0: ON
1: OFF
5973 [User Stamp Registration]
5-973-101 Frame deletion setting
5985 [Device Setting]
CTL [0 to 3 / 0 / 1]
5-985-001 On Board NIC
5-985-002 On Board USB
5990 [SP Print Mode]
5-990-001 All (Data List)
5-990-002 SP (Mode Data List)
5-990-003 User Program
5-990-004 Logging Data
5-990-005 Diagnostic Report
5-990-006 Non-Default
5-990-007 NIB Summary
5-990-008 Capture Log
5-990-021 Copier User Program
5-990-022 Scanner SP
5-990-023 Scanner User Program
5-990-024 SDK/J Summary
5-990-025 SDK/J Application Info
5-990-026 Printer SP
5-990-027 SmartOperationPanel SP
5-990-028 SmartOperationPanel UP
5992 [SP Text mode]
Controller SP Tables - SP5000
CTL
CTL
[0 to 2 / 0 / 1]
0: Disable
1: Enable
2: Function limitation
[0 or 1 / 0 / 1]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
567
568
4. Controller SP Mode Tables
5-992-001 All (Data List)
5-992-002 SP (Mode Data List)
5-992-003 User Program
5-992-004 Logging Data
5-992-005 Diagnostic Report
5-992-006 Non-Default
5-992-007 NIB Summary
5-992-008 Capture Log
5-992-021 Copier User Program
5-992-022 Scanner SP
5-992-023 Scanner User Program
5-992-024 SDK/J Summary
5-992-025 SDK/J Application Info
5-992-026 Printer SP mode
5-992-027 SmartOperationPanel SP
5-992-028 SmartOperationPanel UP
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
[- / - / -]
[Execute]
[- / - / -]
[Execute]
[- / - / -]
[Execute]
Controller SP Tables - SP7000
7401 [Total SC]
Stores total SC occurring count.
If the same SC codes are detected continuously and total counter is not increasing, it only logs once in case of deleting other SC code logs.
7-401-001 SC Counter *CTL [0 to 65535 / 0 / 1/step]
7-401-002 Total SC Counter *CTL [0 to 65535 / 0 / 1/step]
7403 [SC History]
Logs and displays the SC codes detected.
The 10 most recently detected SC Codes are displayed on the screen, and also can be seen on the SMC (logging) outputs.
• If the same SC codes are detected continuously and total counter is not increasing, it only logs once in case of deleting other SC code logs.
7-403-001 Latest *CTL [- / - / -]
7-403-002 Latest 1
7-403-003 Latest 2
7-403-004 Latest 3
7-403-005 Latest 4
*CTL
*CTL
*CTL
*CTL
7-403-006 Latest 5
7-403-007 Latest 6
7-403-008 Latest 7
7-403-009 Latest 8
7-403-010 Latest 9
*CTL
*CTL
*CTL
*CTL
*CTL
569
570
4. Controller SP Mode Tables
7404 [Software Error History]
7-404-001 Latest
7-404-002 Latest 1
7-404-003 Latest 2
7-404-004 Latest 3
7-404-005 Latest 4
7-404-006 Latest 5
7-404-007 Latest 6
7-404-008 Latest 7
7-404-009 Latest 8
7-404-010 Latest 9
7502 [Total Paper Jam]
7-502-001 Jam Counter
7-502-002 Total Jam Counter
7503
7-503-001 -
[Total Original Jam Counter]
7503 [Total Original Jam]
7-503-002 Total Original Counter
7504 [Paper Jam Location]
7-504-001 At Power On
7-504-003 Tray 1: On
7-504-004 Tray 2: On
7-504-005 Tray 3: On
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL [0 to 65535 / 0 / 1sheet/step]
*CTL [0 to 65535 / 0 / 1sheet/step]
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[- / - / -]
[0 to 65535 / 0 / 1/step]
[0 to 65535 / 0 / 1/step]
Paper is not fed at power on.
[0 to 65535 / 0 / 1/step]
[0 to 65535 / 0 / 1/step]
[0 to 65535 / 0 / 1/step]
[0 to 65535 / 0 / 1/step]
Controller SP Tables - SP7000
7-504-006 Tray 4: On
7-504-007 LCT: On
7-504-008 Bypass: On
7-504-009 Duplex: On
7-504-011 Transport Sensor 1: On
7-504-012 Transport Sensor 2: On
7-504-013 Vertical Trans. Sn 3: On
7-504-014 Vertical Trans. Sn 4: On
7-504-015 LCT Transport Sensor: On
7-504-017 Registration Sensor: On
7-504-018 Fusing Entrance Sensor: On
7-504-019 Fusing Exit Sensor: On
7-504-020 Paper Exit Sensor: On
7-504-021 Bridge Exit: On
7-504-022 Bridge Transport: On
7-504-024 Inverter Sn: On
7-504-025 Duplex Exit Sensor: On
7-504-027 Duplex Entrance Sensor: On
7-504-048 Bypass Transport Sensor 1: Off
7-504-051 Transport Sensor 1: Off
7-504-052 Transport Sensor 2: Off
7-504-053 Vertical Trans. Sn 3: Off
7-504-054 Vertical Trans. Sn 4: Off
7-504-057 Registration Sensor: Off
7-504-058 LCT Transport Sensor: Off
7-504-060 Paper Exit Sensor: Off
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
571
572
4. Controller SP Mode Tables
7-504-061 Bridge Exit Sensor: Off
7-504-062 Bridge Transport: Off
7-504-064 Inverter Sensor: Off
7-504-065 Duplex Exit Sensor: Off
7-504-067 Duplex Entrance Sensor: Off
7-504-096 Timing: On
7-504-100 Entrance Sensor: On
7-504-101 Entrance Sensor: Off
7-504-102 Transport Sensor: On
7-504-103 Transport Sensor: Off
7-504-104 Paper Exit
7-504-105 Front Jogger Motor
7-504-106 Rear Jogger Motor
7-504-107 Shift Roller Motor
7-504-108 Positioning Roller Motor
7-504-109 Exit Guide Plate Motor
7-504-110 Stapler Movement Motor
7-504-111 Shift Tray Lift Motor
7-504-112 Staple Motor
7-504-113 Paper Stopper Motor
7-504-114 Punch Motor
7-504-115 Punch Unit Movement Motor
7-504-116 Horizontal Reg. Movement
Motor
7-504-148 No Exit Response
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
Controller SP Tables - SP7000
7-504-149 Invalid Main Machine Data
Setting
7-504-150 Entrance Sensor: On
7-504-151 Entrance Sensor: Off
7-504-152 Horizontal Transport Sn: On
7-504-153 Horizontal Transport Sn: Off
7-504-154 Switchback Transport Sn: On
7-504-155 Switchback Transport Sn: Off
7-504-156 Proof Tray Exit: On
7-504-157 Proof Tray Exit: Off
7-504-158 Shift Tray Exit: On
7-504-159 Shift Tray Exit: Off
7-504-160 Booklet Stapler Exit: On
7-504-161 Booklet Stapler Exit: Off
7-504-162 Entrance Transport Motor
7-504-163 Horizontal Transport Motor
7-504-164 Pre-Stack Transport Motor
7-504-165 Intermediate Transport Motor
7-504-166 Paper Exit Motor
7-504-167 Trailing Edge Stopper Motor
7-504-168 Paper Exit Guide Plate Motor
7-504-169 Punch Unit Drive Motor
7-504-170 Punch Unit Movement Motor
7-504-171 S-to-S Regist Move Motor
7-504-172 Lower Junction Gate Motor
7-504-173 Jogger Motor
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
573
574
4. Controller SP Mode Tables
7-504-174 Positioning Roller Drive Motor
7-504-175 Feed Out Motor
7-504-176 Corner Stapler Movement Motor
7-504-177 Corner Stapler Motor
7-504-178 Booklet Jogger Motor
7-504-179 Booklet Guide Motor
7-504-180 Booklet Jogger Fence Motor
7-504-181 Booklet Stapler Motor
7-504-182 Movement Roller Transport
Motor
7-504-183 Folding Transport Motor
7-504-184 Square Folding Motor
7-504-185 Tray Lift Motor
7-504-186 Shift Motor
7-504-187 Front Shift Jogger Motor
7-504-188 Rear Shift Jogger Motor
7-504-189 Shift Jogger Retraction Motor
7-504-190 Drag Roller Vibrating Motor
7-504-191 Leading Edge Guide Motor
7-504-192 Positioning Transport Motor
7-504-193 Paper Guide Motor
7-504-194 Invalid Main Machine Data
Setting
7-504-200 Entrance: On
7-504-201 Entrance: Off
7-504-202 Proof Tray Exit: On
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
Controller SP Tables - SP7000
7-504-203 Proof Tray Exit: Off
7-504-204 Intermediate Transport (R): On
7-504-205 Intermediate Transport (L): On
7-504-206 Intermediate Transport (L): Off
7-504-207 Shift Tray Paper Exit: On
7-504-208 Shift Tray Paper Exit: Off
7-504-209 Paper Bundle Transport: On
7-504-210 Trailing Edge Stopper Trans.: On
7-504-211 Trailing Edge Stopper Trans.: Off
7-504-212 Center-Folding Exit: On
7-504-213 Center-Folding Exit: Off
7-504-220 Entrance Transport Motor
7-504-221 Proof Transport Motor
7-504-222 Exit Trans./Posit & Move Rllr Mt
7-504-223 Shift Motor
7-504-224 Jogger Motor
7-504-225 Exit Guide Plate Motor
7-504-226 Feed Out Motor
7-504-227 Tray Lift Motor
7-504-228 Positioning Motor
7-504-229 Stapler Movement Motor
7-504-230 Stapler Motor
7-504-231 Punch Motors
7-504-232 Paper Bundle Transport Motors
7-504-233 Trailing Edge Stopper Motor
7-504-234 Folding Blade Motor
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
575
576
4. Controller SP Mode Tables
7-504-235 Paper Guide Motor
7-504-236 Stapleless Stapler Movement
Motor
7-504-237 Stapleless Stapler Motor
7-504-238 Moveable Guide Plate Motor
7-504-248 No Exit Response
7-504-249 Invalid Main Machine Data
Setting
7505 [Original Jam Detection]
7-505-001 At Power On
7-505-013 Separation Sensor: On
7-505-014 Skew Correction Sn: On
7-505-015 Scanning Entrance Sn: On
7-505-016 Registration Sensor: On
7-505-017 Original Exit Sensor: On
7-505-063 Separation Sensor: Off
7-505-034 Skew Correction Sn: Off
7-505-065 Scanning Entrance Sn: Off
7-505-066 Registration Sensor: Off
7-505-037 Original Exit Sensor: Off
7-505-239 Original Pullout
7506 [Jam Count by Paper Size]
*CTL
*CTL
[0 to 65535 / 0 / 1/step]
[0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL [0 to 65535 / 0 / 1/step]
*CTL
*CTL
*CTL
*CTL
*CTL
7-506-005 A4 LEF
7-506-006 A5 LEF
7-506-014 B5 LEF
7-506-038 LT LEF
7-506-044 HLT LEF
7-506-132 A3 SEF
7-506-133 A4 SEF
7-506-134 A5 SEF
7-506-141 B4 SEF
7-506-142 B5 SEF
7-506-160 DLT SEF
7-506-164 LG SEF
7-506-166 LT SEF
7-506-172 HLT SEF
7-506-255 Others
7507 [Plotter Jam History]
Controller SP Tables - SP7000
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL [0 to 65535 / 0 / 1/step]
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
577
4. Controller SP Mode Tables
578
7-507-001 Latest
7-507-002 Latest 1
7-507-003 Latest 2
7-507-004 Latest 3
7-507-005 Latest 4
7-507-006 Latest 5
7-507-007 Latest 6
7-507-008 Latest 7
7-507-009 Latest 8
7-507-010 Latest 9
7508 [Original Jam History]
7-508-001 Latest
7-508-002 Latest 1
7-508-003 Latest 2
7-508-004 Latest 3
7-508-005 Latest 4
7-508-006 Latest 5
7-508-007 Latest 6
7-508-008 Latest 7
7-508-009 Latest 8
7-508-010 Latest 9
7509 [Paper Jam Location]
7-509-045 Entrance Sensor: On
7-509-046 Entrance Sensor: Off
7-509-047 Exit Sensor: On
*CTL [-/ - / - ]
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL [- / - / -]
*CTL
*CTL
*CTL
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
Controller SP Tables - SP7000
7-509-048 Exit Sensor: Off
7-509-049 Shift Motor
7-509-050 Junction Solenoid Motor
7-509-051 Exit Paper Pressure Motor
7-509-052 Stapler Motor
7-509-093 No Exit Response
7514 [Paper Jam Count by Location]
7-514-001 At Power On
7-514-003 Tray 1: On
7-514-004 Tray 2: On
7-514-005 Tray 3: On
7-514-006 Tray 4: On
7-514-007 LCT: On
7-514-008 Bypass: On
7-514-009 Duplex: On
7-514-011 Transport Sensor 1: On
7-514-012 Transport Sensor 2: On
7-514-013 Vertical Trans. Sn 3: On
7-514-014 Vertical Trans. Sn 4: On
7-514-015 LCT Transport Sensor: On
7-514-017 Registration Sensor: On
7-514-018 Fusing Entrance Sensor: On
7-514-019 Fusing Exit Sensor: On
7-514-020 Paper Exit Sensor: On
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL Paper is not fed at power on.
[0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
579
580
4. Controller SP Mode Tables
7-514-021 Bridge Exit: On
7-514-022 Bridge Transport: On
7-514-024 Inverter Sn: On
7-514-025 Duplex Exit Sensor: On
7-514-027 Duplex Entrance Sensor: On
7-514-048 Bypass Transport Sensor 1: Off
7-514-051 Transport Sensor 1: Off
7-514-052 Transport Sensor 2: Off
7-514-053 Vertical Trans. Sn 3: Off
7-514-054 Vertical Trans. Sn 4: Off
7-514-057 Registration Sensor: Off
7-514-058 LCT Transport Sensor: Off
7-514-060 Paper Exit Sensor: Off
7-514-061 Bridge Exit Sensor: Off
7-514-062 Bridge Transport: Off
7-514-064 Inverter Sensor: Off
7-514-065 Duplex Exit Sensor: Off
7-514-067 Duplex Entrance Sensor: Off
7-514-096 Timing: On
7-514-100 Entrance Sensor: On
7-514-101 Entrance Sensor: Off
7-514-102 Transport Sensor: On
7-514-103 Transport Sensor: Off
7-514-104 Paper Exit
7-514-105 Front Jogger Motor
7-514-106 Rear Jogger Motor
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
Controller SP Tables - SP7000
7-514-107 Shift Roller Motor
7-514-108 Positioning Roller Motor
7-514-109 Exit Guide Plate Motor
7-514-110 Stapler Movement Motor
7-514-111 Shift Tray Lift Motor
7-514-112 Staple Motor
7-514-113 Paper Stopper Motor
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
7-514-114 Punch Motor
7-514-115 Punch Unit Movement Motor
7-514-116 Horizontal Reg. Movement Motor
7-514-148 No Exit Response
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
7-514-149 Invalid Main Machine Data Setting *CTL [0 to 65535 / 0 / 1/step]
7-514-150 Entrance Sensor: On *CTL [0 to 65535 / 0 / 1/step]
7-514-151 Entrance Sensor: Off
7-514-152 Horizontal Transport Sn: On
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
7-514-153 Horizontal Transport Sn: Off
7-514-154 Switchback Transport Sn: On
7-514-155 Switchback Transport Sn: Off
7-514-156 Proof Tray Exit: On
7-514-157 Proof Tray Exit: Off
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
7-514-158 Shift Tray Exit: On
7-514-159 Shift Tray Exit: Off
7-514-160 Booklet Stapler Exit: On
7-514-161 Booklet Stapler Exit: Off
7-514-162 Entrance Transport Motor
7-514-163 Horizontal Transport Motor
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
581
582
4. Controller SP Mode Tables
7-514-164 Pre-Stack Transport Motor
7-514-165 Intermediate Transport Motor
7-514-166 Paper Exit Motor
7-514-167 Trailing Edge Stopper Motor
7-514-168 Paper Exit Guide Plate Motor
7-514-169 Punch Unit Drive Motor
7-514-170 Punch Unit Movement Motor
7-514-171 S-to-S Regist Move Motor
7-514-172 Lower Junction Gate Motor
7-514-173 Jogger Motor
7-514-174 Positioning Roller Drive Motor
7-514-175 Feed Out Motor
7-514-176 Corner Stapler Movement Motor
7-514-177 Corner Stapler Motor
7-514-178 Booklet Jogger Motor
7-514-179 Booklet Guide Motor
7-514-180 Booklet Jogger Fence Motor
7-514-181 Booklet Stapler Motor
7-514-182 Movement Roller Transport Motor
7-514-183 Folding Transport Motor
7-514-184 Square Folding Motor
7-514-185 Tray Lift Motor
7-514-186 Shift Motor
7-514-187 Front Shift Jogger Motor
7-514-188 Rear Shift Jogger Motor
7-514-189 Shift Jogger Retraction Motor
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
Controller SP Tables - SP7000
7-514-190 Drag Roller Vibrating Motor
7-514-191 Leading Edge Guide Motor
7-514-192 Positioning Transport Motor
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
7-514-193 Paper Guide Motor *CTL [0 to 65535 / 0 / 1/step]
7-514-194 Invalid Main Machine Data Setting *CTL [0 to 65535 / 0 / 1/step]
7-514-200 Entrance: On
7-514-201 Entrance: Off
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
7-514-202 Proof Tray Exit: On
7-514-203 Proof Tray Exit: Off
7-514-204 Intermediate Transport (R): On
7-514-205 Intermediate Transport (L): On
7-514-206 Intermediate Transport (L): Off
7-514-207 Shift Tray Paper Exit: On
7-514-208 Shift Tray Paper Exit: Off
7-514-209 Paper Bundle Transport: On
7-514-210 Trailing Edge Stopper Trans.: On
7-514-211 Trailing Edge Stopper Trans.: Off
7-514-212 Center-Folding Exit: On
7-514-213 Center-Folding Exit: Off
7-514-220 Entrance Transport Motor
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[0 to 65535 / 0 / 1/step]
[0 to 65535 / 0 / 1/step]
[0 to 65535 / 0 / 1/step]
[0 to 65535 / 0 / 1/step]
[0 to 65535 / 0 / 1/step]
[0 to 65535 / 0 / 1/step]
[0 to 65535 / 0 / 1/step]
[0 to 65535 / 0 / 1/step]
[0 to 65535 / 0 / 1/step]
[0 to 65535 / 0 / 1/step]
[0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
7-514-221 Proof Transport Motor
7-514-222 Exit Trans./Posit & Move Rllr Mt
7-514-223 Shift Motor
7-514-224 Jogger Motor
7-514-225 Exit Guide Plate Motor
7-514-226 Feed Out Motor
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
583
584
4. Controller SP Mode Tables
7-514-227 Tray Lift Motor
7-514-228 Positioning Motor
7-514-229 Stapler Movement Motor
7-514-230 Stapler Motor
7-514-231 Punch Motors
7-514-232 Paper Bundle Transport Motors
7-514-233 Trailing Edge Stopper Motor
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
7-514-234 Folding Blade Motor
7-514-235 Paper Guide Motor
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step] 7-514-236 Stapleless Stapler Movement
Motor
7-514-237 Stapleless Stapler Motor
7-514-238 Moveable Guide Plate Motor
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
7-514-248 No Exit Response *CTL [0 to 65535 / 0 / 1/step]
7-514-249 Invalid Main Machine Data Setting *CTL [0 to 65535 / 0 / 1/step]
7515 [Original Jam Count by Detection]
7-515-001 At Power On
7-515-013 Separation Sensor: On
7-515-014 Skew Correction Sn: On
7-515-015 Scanning Entrance Sn: On
7-515-016 Registration Sensor: On
7-515-017 Original Exit Sensor: On
7-515-063 Separation Sensor: Off
7-515-034 Skew Correction Sn: Off
7-515-035 Scanning Entrance Sn: Off
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
Controller SP Tables - SP7000
7-515-066 Registration Sensor: Off
7-515-067 Original Exit Sensor: Off
7-515-239 Original Pullout
7519 [Paper Jam Count by Location]
7-519-045 Entrance Sensor: On
7-519-046 Entrance Sensor: Off
7-519-047 Exit Sensor: On
7-519-048 Exit Sensor: Off
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
*CTL [0 to 65535 / 0 / 1/step]
7516 [Jam Paper Size Cnt]
Displays occurring count of transfer paper jams by each paper size.
7-516-005 A4 LEF
7-516-006 A5 LEF
*CTL [0 to 9999 / 0 / 1 sheet/step]
*CTL
7-516-014 B5 LEF
7-516-038 LT LEF
7-516-044 HLT LEF
7-516-132 A3 SEF
*CTL
*CTL
*CTL
*CTL [0 to 9999 / 0 / 1 sheet/step]
7-516-133 A4 SEF
7-516-134 A5 SEF
7-516-141 B4 SEF
7-516-142 B5 SEF
7-516-160 DLT SEF
7-516-164 LG SEF
7-516-166 LT SEF
7-516-172 HLT SEF
7-516-255 Others
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[0 to 9999 / 0 / 1 sheet/step]
*CTL [0 to 65535 / 0 / 0]
*CTL [0 to 65535 / 0 / 0]
*CTL [0 to 65535 / 0 / 0]
*CTL [0 to 65535 / 0 / 0]
585
586
4. Controller SP Mode Tables
7-519-049 Shift Motor
7-519-050 Junction Solenoid Motor
7-519-051 Exit Paper Pressure Motor
7-519-052 Stapler Motor
7-519-093 No Exit Response
7520 [Update Log]
7-520-001 ErrorRecord1
7-520-002 ErrorRecord2
7-520-003 ErrorRecord3
7-520-004 ErrorRecord4
7-520-005 ErrorRecord5
7-520-006 ErrorRecord6
7-520-007 ErrorRecord7
7-520-008 ErrorRecord8
7-520-009 ErrorRecord9
7-520-010 ErrorRecord10
7-520-011 Auto:StartDate1
7-520-012 Auto:StartDate2
7-520-013 Auto:StartDate3
7-520-014 Auto:StartDate4
7-520-015 Auto:StartDate5
7-520-021 Auto:EndDate1
7-520-022 Auto:EndDate2
7-520-023 Auto:EndDate3
7-520-024 Auto:EndDate4
*CTL [0 to 65535 / 0 / 0]
*CTL [0 to 65535 / 0 / 0]
*CTL [0 to 65535 / 0 / 0]
*CTL [0 to 65535 / 0 / 0]
*CTL [0 to 65535 / 0 / 0]
*CTL [0 to 255 / 0 / 1]
*CTL [0 to 255 / 0 / 1]
*CTL [0 to 255 / 0 / 1]
*CTL [0 to 255 / 0 / 1]
*CTL [0 to 255 / 0 / 1]
*CTL [0 to 255 / 0 / 1]
*CTL [0 to 255 / 0 / 1]
*CTL [0 to 255 / 0 / 1]
*CTL [0 to 255 / 0 / 1]
*CTL [0 to 255 / 0 / 1]
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [- / - / -]
Controller SP Tables - SP7000
7-520-025 Auto:EndDate5
7-520-031 Auto:Piecemark1
7-520-032 Auto:Piecemark2
7-520-033 Auto:Piecemark3
7-520-034 Auto:Piecemark4
7-520-035 Auto:Piecemark5
7-520-041 Auto:Version1
7-520-042 Auto:Version2
7-520-043 Auto:Version3
7-520-044 Auto:Version4
7-520-045 Auto:Version5
7-520-051 Auto:Result1
7-520-052 Auto:Result2
7-520-053 Auto:Result3
7-520-054 Auto:Result4
7-520-055 Auto:Result5
7-520-056 Auto:Result6
7-520-057 Auto:Result7
7-520-058 Auto:Result8
7-520-059 Auto:Result9
7-520-060 Auto:Result10
7624 [Parts Replacement Operation ON/OFF]
7-624-002 #Photoconductor Unit (Black)
7-624-003 #Development unit: Bk
7-624-025 #Photoconductor Unit (Cyan)
*CTL
*CTL
*CTL
[0 or 1 / 1 / 1]
[0 or 1 / 1 / 1]
[0 or 1 / 1 / 1]
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [0 to 255 / 0 / 1]
*CTL [0 to 255 / 0 / 1]
*CTL [0 to 255 / 0 / 1]
*CTL [0 to 255 / 0 / 1]
*CTL [0 to 255 / 0 / 1]
*CTL [0 to 255 / 0 / 1]
*CTL [0 to 255 / 0 / 1]
*CTL [0 to 255 / 0 / 1]
*CTL [0 to 255 / 0 / 1]
*CTL [0 to 255 / 0 / 1]
587
588
4. Controller SP Mode Tables
7-624-026 #Development unit: C *CTL [0 or 1 / 1 / 1]
7-624-048 #Photoconductor Unit (Magenta) *CTL [0 or 1 / 1 / 1]
7-624-049 #Development unit: M *CTL [0 or 1 / 1 / 1]
7-624-071 #Photoconductor Unit (Yellow)
7-624-072 #Development unit: Y
7-624-093 #Intermediate Transfer Unit
7-624-102 #ITB Cleaning Unit
*CTL
*CTL
*CTL
*CTL
[0 or 1 / 1 / 1]
[0 or 1 / 1 / 1]
[0 or 1 / 1 / 1]
[0 or 1 / 1 / 1]
7-624-109 #Paper Transfer Unit
7-624-115 #Fuser Unit
7-624-116 Fuser Unit: Belt
7-624-118 Fuser Unit: Pressure Roller
7-624-131 #Dust Filter
7-624-142 #Wast Toner bottle
7-624-206 #ADF Pick-up Roller
7-624-207 #ADF Paper Supply Belt
7-624-208 #ADF Separate Roller
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[0 or 1 / 1 / 1]
[0 or 1 / 1 / 1]
[0 or 1 / 1 / 1]
[0 or 1 / 1 / 1]
[0 or 1 / 1 / 1]
[0 or 1 / 1 / 1]
*CTL [0 or 1 / 1 / 1]
*CTL [0 or 1 / 1 / 1]
*CTL [0 or 1 / 1 / 1]
7801
7-801-255 -
[ROM No./ Firmware Version]
7803 [PM Counter Display]
7-803-001 Paper
7804 [PM Counter Reset]
7-804-001 Paper
CTL
*CTL
CTL
[- / - / -]
[0 to 999999 / 0 / 1/step]
[- / - / -]
[Execute]
7807 [SC/Jam Counter Reset]
Controller SP Tables - SP7000
7-807-001 *CTL [- / - / -]
[Execute]
7826 [MF Error Counter]
7-826-001 Error Total
7-826-002 Error Staple
7827
7-827-001 -
[MF Error Counter Clear]
*CTL
*CTL
[0 to 9999999 / - / 1/step]
[0 to 9999999 / - / 1/step]
*CTL [- / - / -]
[Execute]
7832
7-832-001 -
[Self-Diagnose Result Display]
CTL [- / - / -]
[Execute]
7835 [ACC Counter]
7-835-001 Copy ACC
7-835-002 Printer ACC
*CTL [0 to 9999999 / - / 1/step]
*CTL [0 to 9999999 / - / 1/step]
7836 [Total Memory Size]
Displays the memory capacity of the controller system.
7-836-001 Total Memory Size CTL [- / - / -]
7840 [Service SP Entry Code Chg Hist]
7-840-001 Change Time :Latest
7-840-002 Change Time : Last1
7-840-101 Initialize Time : Latest
7-840-102 Initialize Time : Last1
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [- / - / -]
7851 [Unified Counter]
589
590
4. Controller SP Mode Tables
7-851-001 Copy Program Number
Registered
7855 [Coverage Range]
7-855-001 Coverage Range 1
7-855-002 Coverage Range 2
7901 [Assert Info.]
7-901-001 File Name
7-901-002 Number of Lines
7-901-003 Location
7910 [ROM No]
7-910-001 System/Copy
7-910-002 Engine
7-910-003 Lcdc
7-910-005 ADF
7-910-007 Finisher1
7-910-009 Bank
7-910-010 LCT
7-910-012 FCU
7-910-018 NetworkSupport
7-910-019 Bank2
7-910-022 BIOS
7-910-023 HDD Format Option
7-910-150 RPCS
7-910-151 PS
*CTL [0 to 255 / 0 / 1/step]
*CTL [1 to 200 / 5 /1]
*CTL [1 to 200 / 20 /1]
*CTL [- / - / -]
*CTL [- / - / -]
*CTL [- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
7-910-152 RPDL
7-910-153 R98
7-910-154 R16
7-910-155 RPGL
7-910-156 R55
7-910-157 RTIFF
7-910-158 PCL
7-910-159 PCLXL
7-910-160 MSIS
7-910-162 PDF
7-910-164 PictBridge
7-910-165 PJL
7-910-167 MediaPrint:JPEG
7-910-168 MediaPrint:TIFF
7-910-169 XPS
7-910-180 FONT
7-910-181 FONT1
7-910-182 FONT2
7-910-183 FONT3
7-910-184 FONT4
7-910-185 FONT5
7-910-200 Factory
7-910-201 Copy
7-910-202 NetworkDocBox
7-910-203 Fax
7-910-204 Printer
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
Controller SP Tables - SP7000
591
592
4. Controller SP Mode Tables
7-910-205 Scanner
7-910-206 RFax
7-910-210 MIB
7-910-211 Websupport
7-910-212 WebUapl
7-910-213 SDK1
7-910-214 SDK2
7-910-215 SDK3
7-910-250 Package
7911 [Firmware Version]
7-911-001 System/Copy
7-911-002 Engine
7-911-003 Lcdc
7-911-005 ADF
7-911-007 Finisher1
7-911-009 Bank
7-911-010 LCT
7-911-012 FCU
7-911-018 NetworkSupport
7-911-019 Bank2
7-911-022 BIOS
7-911-023 HDD Format Option
7-911-150 RPCS
7-911-151 PS
7-911-152 RPDL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
7-911-153 R98
7-911-154 R16
7-911-155 RPGL
7-911-156 R55
7-911-157 RTIFF
7-911-158 PCL
7-911-159 PCLXL
7-911-160 MSIS
7-911-162 PDF
7-911-164 PictBridge
7-911-165 PJL
7-911-167 MediaPrint:JPEG
7-911-168 MediaPrint:TIFF
7-911-169 XPS
7-911-180 FONT
7-911-181 FONT1
7-911-182 FONT2
7-911-183 FONT3
7-911-184 FONT4
7-911-185 FONT5
7-911-200 Factory
7-911-201 Copy
7-911-202 NetworkDocBox
7-911-203 Fax
7-911-204 Printer
7-911-205 Scanner
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
Controller SP Tables - SP7000
593
594
4. Controller SP Mode Tables
7-911-206 RFax
7-911-210 MIB
7-911-211 Websupport
7-911-212 WebUapl
7-911-213 SDK1
7-911-214 SDK2
7-911-215 SDK3
7-911-250 Package
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
[- / - / -]
Controller SP Tables - SP8000
Many of these counters are provided for features that are currently not available, such as sending color faxes, and so on. However, here are some Group 8 codes that when used in combination with others, can provide useful information.
SP Numbers
SP8211 to SP8216
SP8401 to SP8406
SP8691 to SP8696
What They Do
The number of pages scanned to the document server.
The number of pages printed from the document server
The number of pages sent from the document server
Specifically, the following questions can be answered:
• How is the document server actually being used?
• What application is using the document server most frequently?
• What data in the document server is being reused?
Most of the SPs in this group are prefixed with a letter that indicates the mode of operation (the mode of operation is referred to as an "application"). Before reading the Group 8 Service Table, make sure that you understand what these prefixes mean.
T:
P:
S:
C:
F:
Prefixes
Total: (Grand Total).
Copy application.
Fax application.
Print application.
Scan application.
What it means
Grand total of the items counted for all applications (C, F,
P, etc.).
Totals (pages, jobs, etc.) executed for each application when the job was not stored on the document server.
595
596
4. Controller SP Mode Tables
L:
O:
Local storage (document server)
Other applications
(external network applications, for example)
Totals (jobs, pages, etc.) for the document server. The L: counters work differently case by case. Sometimes, they count jobs/pages stored on the document server; this can be in document server mode (from the document server window), or from another mode, such as from a printer driver or by pressing the Store File button in the Copy mode window. Sometimes, they include occasions when the user uses a file that is already on the document server.
Each counter will be discussed case by case.
Refers to network applications such as Web Image
Monitor. Utilities developed with the SDK (Software
Development Kit) will also be counted with this group in the future.
The Group 8 SP codes are limited to 17 characters, forced by the necessity of displaying them on the small LCDs of printers and faxes that also use these SPs. Read over the list of abbreviations below and refer to it again if you see the name of an SP that you do not understand.
Abbreviation
/
>
AddBook
Apl
B/W
Bk
C
ColCr
ColMode
Comb
Comp
What it means
"By", e.g. "T:Jobs/Apl" = Total Jobs "by" Application
More (2> "2 or more", 4> "4 or more"
Address Book
Application
Black & White
Black
Cyan
Color Create
Color Mode
Combine
Compression
Controller SP Tables - SP8000
IFax
ImgEdt
K
LS
LSize
Mag
MC
NRS
Org
OrgJam
Deliv
DesApl
Abbreviation
Dev Counter
Dup, Duplex
Emul
FC
FIN
Full Bleed
GenCopy
GPC
What it means
Delivery
Designated Application. The application (Copy, Fax, Scan, Print) used to store the job on the document server, for example.
Development Count, no. of pages developed.
Duplex, printing on both sides
Emulation
Full Color
Post-print processing, i.e. finishing (punching, stapling, etc.)
No Margins
Generation Copy Mode
Get Print Counter. For jobs 10 pages or less, this counter does not count up. For jobs larger than 10 pages, this counter counts up by the number that is in excess of 10 (e.g., for an 11-page job, the counter counts up
11-10 =1)
Internet Fax
Image Edit performed on the original with the copier GUI, e.g. border removal, adding stamps, page numbers, etc.
Black (YMCK)
Local Storage. Refers to the document server.
Large (paper) Size
Magnification
One color (monochrome)
New Remote Service, which allows a service center to monitor machines remotely. "NRS" is used overseas, "CSS" is used in Japan.
Original for scanning
Original Jam
597
598
4. Controller SP Mode Tables
Svr
TonEnd
TonSave
TXJob
YMC
YMCK
PJob
Ppr
PrtJam
PrtPGS
R
Rez
SC
Scn
Sim, Simplex
S-to-Email
SMC
Palm 2
Abbreviation
PC
PGS
What it means
Print Job Manager/Desk Top Editor: A pair of utilities that allows print jobs to be distributed evenly among the printers on the network, and allows files to moved around, combined, and converted to different formats.
Personal Computer
Pages. A page is the total scanned surface of the original. Duplex pages count as two pages, and A3 simplex count as two pages if the A3/DLT counter SP is switched ON.
Print Jobs
Paper
Printer (plotter) Jam
Print Pages
Red (Toner Remaining). Applies to the wide format model A2 only. This machine is under development and currently not available.
Resolution
Service Code (Error SC code displayed)
Scan
Simplex, printing on 1 side.
Scan-to-E-mail
SMC report printed with SP5990. All of the Group 8 counters are recorded in the SMC report.
Server
Toner End
Toner Save
Send, Transmission
Yellow, Magenta, Cyan
Yellow, Magenta, Cyan, Black
Controller SP Tables - SP8000
8001
8002
8003
8004
8005
8006
• All of the Group 8 SPs are able to reset by “SP5 801 1 Memory All Clear”.
[T:Total Jobs]
[C:Total Jobs]
[F:Total Jobs]
[P:Total Jobs]
[S:Total Jobs]
[L:Total Jobs]
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
These SPs count the number of times each application is used to do a job.
[0 to 99999999 / - / 1]
Note: The L: counter is the total number of times the other applications are used to send a job to the document server, plus the number of times a file already on the document server is used.
• These SPs reveal the number of times an application is used, not the number of pages processed.
• When an application is opened for image input or output, this counts as one job.
• Interrupted jobs (paper jams, etc.) are counted, even though they do not finish.
• Only jobs executed by the customer are counted. Jobs executed by the customer engineer using the SP modes are not counted.
• When using secure printing (when a password is required to start the print job), the job is counted at the time when either "Delete Data" or "Specify Output" is specified.
• A job is counted as a fax job when the job is stored for sending.
• When a fax is received to fax memory, the F: counter increments but the L: counter does not (the document server is not used).
• A fax broadcast counts as one job for the F: counter (the fax destinations in the broadcast are not counted separately).
• A fax broadcast is counted only after all the faxes have been sent to their destinations. If one transmission generates an error, then the broadcast will not be counted until the transmission has been completed.
• A printed fax report counts as one job for the F: counter.
• The F: counter does not distinguish between fax sending or receiving.
• When a copy job on the document server is printed, SP8022 also increments, and when a print job stored on the document server is printed, SP8024 also increments.
• When an original is both copied and stored on the document server, the C: and L: counters both increment.
• When a print job is stored on the document server, only the L: counter increments.
• When the user presses the Document Server button to store the job on the document server, only the L: counter increments.
599
600
4. Controller SP Mode Tables
8011
8012
8013
8014
8015
8016
8017
• When the user enters document server mode and prints data stored on the document server, only the L: counter increments.
• When an image received from Palm 2 is received and stored, the L: counter increments.
• When the customer prints a report (user code list, for example), the O: counter increments.
However, for fax reports and reports executed from the fax application, the F: counter increments.
[T:Jobs/LS]
[C:Jobs/LS]
[F:Jobs/LS]
[P:Jobs/LS]
[S:Jobs/LS]
[L:Jobs/LS]
[O:Jobs/LS]
*CTL These SPs count the number of jobs stored to the document server by each application, to
*CTL reveal how local storage is being used for input.
*CTL
[0 to 99999999 / 0 / 1]
*CTL
*CTL
The L: counter counts the number of jobs stored from within the document server mode screen at the operation panel.
*CTL
*CTL
8021
8022
8023
8024
8025
8026
8027
• When a scan job is sent to the document server, the S: counter increments. When you enter document server mode and then scan an original, the L: counter increments.
• When a print job is sent to the document server, the P: counter increments.
• When a network application sends data to the document server, the O: counter increments.
• When an image from Palm 2 is stored on the document server, the O: counter increments.
• When a fax is sent to the document server, the F: counter increments.
[T:Pjob/LS]
[C:Pjob/LS]
[F:Pjob/LS]
[P:Pjob/LS]
[S:Pjob/LS]
[L:Pjob/LS]
[O:Pjob/LS]
*CTL These SPs reveal how files printed from the document server were stored on the
*CTL document server originally.
*CTL
[0 to 99999999 / 0 / 1]
*CTL
*CTL
The L: counter counts the number of jobs stored from within the document server mode screen at the operation panel.
*CTL
*CTL
• When a copy job stored on the document server is printed with another application, the C: counter increments.
Controller SP Tables - SP8000
8031
8032
8033
8034
8035
8036
8037
• When an application like DeskTopBinder merges a copy job that was stored on the document server with a print job that was stored on the document server, the C: and P: counters both increment.
• When a job already on the document server is printed with another application, the L: counter increments.
• When a scanner job stored on the document server is printed with another application, the S: counter increments. If the original was scanned from within document server mode, then the L: counter increments.
• When images stored on the document server by a network application (including Palm 2), are printed with another application, the O: counter increments.
• When a copy job stored on the document server is printed with a network application (Web Image
Monitor, for example), the C: counter increments.
• When a fax on the document server is printed, the F: counter increments.
[T:Pjob/DesApl]
[C:Pjob/DesApl]
[F:Pjob/DesApl]
[P:Pjob/DesApl]
[S:Pjob/DesApl]
[L:Pjob/DesApl]
[O:Pjob/DesApl]
*CTL These SPs reveal what applications were used to output documents from the document
*CTL server.
*CTL
[0 to 99999999 / 0 / 1]
*CTL
*CTL
The L: counter counts the number of jobs printed from within the document server mode screen at the operation panel.
*CTL
*CTL
• When documents already stored on the document server are printed, the count for the application that started the print job is incremented.
• When the print job is started from a network application (Desk Top Binder, Web Image Monitor, etc.) the L: counter increments.
601
602
4. Controller SP Mode Tables
8041
8042
8043
8044
8045
8046
8047
[T:TX Jobs/LS]
[C:TX Jobs/LS]
[F:TX Jobs/LS]
[P:TX Jobs/LS]
[S:TX Jobs/LS]
[L:TX Jobs/LS]
[O:TX Jobs/LS]
*CTL These SPs count the applications that stored files on the document server that were later
*CTL accessed for transmission over the telephone
*CTL line or over a network (attached to an e-mail, or as a fax image by I-Fax).
*CTL
[0 to 99999999 / 0 / 1]
*CTL
*CTL
*CTL
Note: Jobs merged for sending are counted separately.
The L: counter counts the number of jobs scanned from within the document server mode screen at the operation panel.
• When a stored copy job is sent from the document server, the C: counter increments.
• When images stored on the document server by a network application or Palm2 are sent as an email, the O: counter increments.
8051
8052
8053
8054
8055
8056
8057
[T:TX Jobs/DesApl]
[C:TX Jobs/DesApl]
[F:TX Jobs/DesApl]
[P:TX Jobs/DesApl]
[S:TX Jobs/DesApl]
[L:TX Jobs/DesApl]
[O:TX Jobs/DesApl]
*CTL These SPs count the applications used to send files from the document server over the
*CTL telephone line or over a network (attached to
*CTL an e-mail, or as a fax image by I-Fax). Jobs merged for sending are counted separately.
*CTL
*CTL
[0 to 99999999 / 0 / 1]
The L: counter counts the number of jobs sent
*CTL from within the document server mode screen at the operation panel.
*CTL
• If the send is started from Desk Top Binder or Web Image Monitor, for example, then the O: counter increments.
8061
8062
[T:FIN Jobs]
These SPs total the finishing methods. The finishing method is specified by the application.
[P:FIN Jobs]
These SPs total finishing methods for print jobs only. The finishing method is specified by the application.
Controller SP Tables - SP8000
8063
8064
8065
[F:FIN Jobs]
These SPs total finishing methods for fax jobs only. The finishing method is specified by the application.
Note: Finishing features for fax jobs are not available at this time.
[P:FIN Jobs]
These SPs total finishing methods for print jobs only. The finishing method is specified by the application.
[S:FIN Jobs]
These SPs total finishing methods for scan jobs only. The finishing method is specified by the application.
Note: Finishing features for scan jobs are not available at this time.
8066 [L:FIN Jobs]
These SPs total finishing methods for jobs output from within the document server mode screen at the operation panel. The finishing method is specified from the print window within document server mode.
8067 [O:FIN Jobs]
These SPs total finishing methods for jobs executed by an external application, over the network. The finishing method is specified by the application.
001 Sort *CTL [0 to 99999999 / 0 / 1/step]
Number of jobs started in Sort mode.
002 Stack *CTL [0 to 99999999 / 0 / 1/step]
Number of jobs started out of Sort mode.
003 Staple *CTL [0 to 99999999 / 0 / 1/step]
Number of jobs started in Staple mode.
004 Booklet *CTL [0 to 99999999 / 0 / 1/step]
Number of jobs started in Booklet mode. If the machine is in staple mode, the Staple counter also increments.
603
604
4. Controller SP Mode Tables
8071
8072
8073
8074
005 Z-Fold *CTL [0 to 99999999 / 0 / 1/step]
Number of jobs started In any mode other than the Booklet mode and set for folding (Zfold).
006 Punch *CTL [0 to 99999999 / 0 / 1/step]
Number of jobs started in Punch mode. When Punch is set for a print job, the P: counter increments. (See SP8-064-6.)
007 Other *CTL [0 to 99999999 / 0 / 1/step]
008 Inside-Flod
009 Three-In-Fold
010 Three-OUT-Fold
011 Four-Fold
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
012 KANNON-Fold
013 Perfect-Bind
014 Ring-Bind
015 3rd Vendor
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
[T:Jobs/PGS]
These SPs count the number of jobs broken down by the number of pages in the job, regardless of which application was used.
[C:Jobs/PGS]
These SPs count and calculate the number of copy jobs by size based on the number of pages in the job.
[F:Jobs/PGS]
These SPs count and calculate the number of fax jobs by size based on the number of pages in the job.
[P:Jobs/PGS]
These SPs count and calculate the number of print jobs by size based on the number of pages in the job.
Controller SP Tables - SP8000
8075
8076
8077
[S:Jobs/PGS]
These SPs count and calculate the number of scan jobs by size based on the number of pages in the job.
[L:Jobs/PGS]
These SPs count and calculate the number of jobs printed from within the document server mode window at the operation panel, by the number of pages in the job.
[O:Jobs/PGS]
These SPs count and calculate the number of "Other" application jobs (Web Image
Monitor, Palm 2, etc.) by size based on the number of pages in the job.
001 1 Page
002 2 Pages
003 3 Pages
004 4 Pages
005 5 Pages
006 6 to 10 Pages
007 11 to 20 Pages
008 21 to 50 Pages
009 51 to 100 Pages
010 101 to 300 Pages
011 301 to 500 Pages
012 501 to 700 Pages
013 701 to 1000 Pages
014 1001 to Pages
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
• For example: When a copy job stored on the document server is printed in document server mode, the appropriate L: counter (SP8076 0xx) increments.
• Printing a fax report counts as a job and increments the F: counter (SP 8073).
• Interrupted jobs (paper jam, etc.) are counted, even though they do not finish.
• If a job is paused and re-started, it counts as one job.
605
606
4. Controller SP Mode Tables
• If the finisher runs out of staples during a print and staple job, then the job is counted at the time the error occurs.
• For copy jobs (SP 8072) and scan jobs (SP 8075), the total is calculated by multiplying the number of sets of copies by the number of pages scanned. (One duplex page counts as 2.)
• The first test print and subsequent test prints to adjust settings are added to the number of pages of the copy job (SP 8072).
• When printing the first page of a job from within the document server screen, the page is counted.
8111 [T:FAX TX Jobs]
These SPs count the total number of jobs (color or black-and-white) sent by fax, either directly or using a file stored on the document server, on a telephone line.
Note: Color fax sending is not available at this time.
001 B/W
002 Color
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
8113 [F:FAX TX Jobs]
These SPs count the total number of jobs (color or black-and-white) sent by fax directly on a telephone line.
Note: Color fax sending is not available at this time.
001 B/W
002 Color
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
• These counters count jobs, not pages.
• This SP counts fax jobs sent over a telephone line with a fax application, including documents stored on the document server.
• If the mode is changed during the job, the job will count with the mode set when the job started.
• If the same document is faxed to both a public fax line and an I-Fax at a destination where both are available, then this counter increments, and the I-Fax counter (8 12x) also increments.
• The fax job is counted when the job is scanned for sending, not when the job is sent.
8121 [T:IFAX TX Jobs]
These SPs count the total number of jobs (color or black-and-white) sent, either directly or using a file stored on the document server, as fax images using I-Fax.
Note: Color fax sending is not available at this time.
Controller SP Tables - SP8000
8123 [F:IFAX TX Jobs]
These SPs count the number of jobs (color or black-and-white) sent (not stored on the document server), as fax images using I-Fax.
Note: Color fax sending is not available at this time.
001 B/W
002 Color
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
• These counters count jobs, not pages.
• The counters for color are provided for future use; the color fax feature is not available at this time.
• The fax job is counted when the job is scanned for sending, not when the job is sent.
8131
8135
[T:S-to-Email Jobs]
These SPs count the total number of jobs (color or black-and-white) scanned and attached to an e-mail, regardless of whether the document server was used or not.
[S:S-to-Email Jobs]
These SPs count the number of jobs (color or black-and-white) scanned and attached to email, without storing the original on the document server.
001 B/W
002 Color
003 ACS
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
• These counters count jobs, not pages.
• If the job is stored on the document server, after the job is stored it is determined to be color or black-and-white then counted.
• If the job is cancelled during scanning, or if the job is cancelled while the document is waiting to be sent, the job is not counted.
• If the job is cancelled during sending, it may or may not be counted, depending on what stage of the process had been reached when the job was cancelled.
• If several jobs are combined for sending to the Scan Router, Scan-to-Email, or Scan-to-PC, or if one job is sent to more than one destination. each send is counted separately. For example, if the same document is sent by Scan-to-Email as well as Scan-to-PC, then it is counted twice (once for
Scan-to-Email and once for Scan-to-PC).
607
4. Controller SP Mode Tables
608
8141 [T:Deliv Jobs/Svr]
These SPs count the total number of jobs (color or black-and-white) scanned and sent to a
Scan Router server.
8145 [S:Deliv Jobs/Svr]
These SPs count the number of jobs (color or black-and-white) scanned in scanner mode and sent to a Scan Router server.
001 B/W *CTL [0 to 99999999 / 0 / 1/step]
002 Color
003 ACS
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
• These counters count jobs, not pages.
• The jobs are counted even though the arrival and reception of the jobs at the Scan Router server cannot be confirmed.
• If even one color image is mixed with black-and-white images, then the job is counted as a "Color" job.
• If the job is cancelled during scanning, or if the job is cancelled while the document is waiting to be delivered, the job is not counted.
• If the job is cancelled during sending, it may or may not be counted, depending on what stage of the process had been reached when the job was cancelled.
• Even if several files are combined for sending, the transmission counts as one job.
8151 [T:Deliv Jobs/PC]
These SPs count the total number of jobs (color or black-and-white) scanned and sent to a folder on a PC (Scan-to-PC).
Note: At the present time, 8 151 and 8 155 perform identical counts.
8155 [S:Deliv Jobs/PC]
These SPs count the total number of jobs (color or black-and-white) scanned and sent with
Scan-to-PC.
001 B/W *CTL [0 to 99999999 / 0 / 1/step]
002 Color
003 ACS
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
• These counters count jobs, not pages.
Controller SP Tables - SP8000
• If the job is cancelled during scanning, it is not counted.
• If the job is cancelled while it is waiting to be sent, the job is not counted.
• If the job is cancelled during sending, it may or may not be counted, depending on what stage of the process had been reached when the job was cancelled.
• Even if several files are combined for sending, the transmission counts as one job.
8161
8163
[T:PCFAX TX Jobs]
[F:PCFAX TX Jobs]
*CTL
*CTL
These SPs count the number of PC Fax transmission jobs. A job is counted from when it is registered for sending, not when it is sent.
[0 to 99999999 / 0 / 1/step]
Note: At the present time, these counters perform identical counts.
• This counts fax jobs started from a PC using a PC fax application, and sending the data out to the destination from the PC through the copier.
8171
8175
[T:Deliv Jobs/WSD]
These SPs count the pages scanned by WS.
[S:Deliv Jobs/WSD]
These SPs count the pages scanned by WS.
001 B/W
002 Color
003 ACS
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
8181 [T:Scan to Media Jobs]
These SPs count the scanned pages in a media by the scanner application.
[S:Scan to Media Jobs] 8185
These SPs count the scanned pages in a media by the scanner application.
001 B/W *CTL [0 to 99999999 / 0 / 1/step]
002 Color
003 ACS
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
609
610
4. Controller SP Mode Tables
8191
8192
8193
8195
8196
[T:Total Scan PGS]
[C:Total Scan PGS]
[F:Total Scan PGS]
[S:Total Scan PGS]
[L:Total Scan PGS]
*CTL These SPs count the pages scanned by each application that uses the scanner to scan
*CTL images.
*CTL [0 to 99999999 / 0 / 1]
*CTL
*CTL
• SP 8 191 to 8 196 count the number of scanned sides of pages, not the number of physical pages.
• These counters do not count reading user stamp data, or reading color charts to adjust color.
• Previews done with a scanner driver are not counted.
• A count is done only after all images of a job have been scanned.
• Scans made in SP mode are not counted.
Examples
• If 3 B5 pages and 1 A3 page are scanned with the scanner application but not stored, the S: count is 4.
• If both sides of 3 A4 sheets are copied and stored to the document server using the Store File button in the Copy mode window, the C: count is 6 and the L: count is 6.
• If both sides of 3 A4 sheets are copied but not stored, the C: count is 6.
• If you enter document server mode then scan 6 pages, the L: count is 6.
8201
8203
8205
[T:LSize Scan PGS] *CTL [0 to 99999999 / 0 / 1/step]
These SPs count the total number of large pages input with the scanner for scan and copy jobs. Large size paper (A3/DLT) scanned for fax transmission are not counted.
Note: These counters are displayed in the SMC Report, and in the User Tools display.
[F: LSize Scan PGS] *CTL [0 to 99999999 / 0 / 1/step]
These SPs count the total number of large pages input with the scanner for fax transmission.
Note: These counters are displayed in the SMC Report, and in the User Tools display.
[S:LSize Scan PGS] *CTL [0 to 99999999 / 0 / 1/step]
These SPs count the total number of large pages input with the scanner for scan jobs only.
Large size paper (A3/DLT) scanned for fax transmission are not counted.
Note: These counters are displayed in the SMC Report, and in the User Tools display.
Controller SP Tables - SP8000
8211
8212
8213
8215
8216
[T:Scan PGS/LS]
[C:Scan PGS/LS]
[F:Scan PGS/LS]
[S:Scan PGS/LS]
[L:Scan PGS/LS]
*CTL These SPs count the number of pages scanned into the document server.
*CTL
[0 to 99999999 / 0 / 1]
*CTL
*CTL
*CTL
The L: counter counts the number of pages stored from within the document server mode screen at the operation panel, and with the
Store File button from within the Copy mode screen
• Reading user stamp data is not counted.
• If a job is cancelled, the pages output as far as the cancellation are counted.
• If the scanner application scans and stores 3 B5 sheets and 1 A4 sheet, the S: count is 4.
• If pages are copied but not stored on the document server, these counters do not change.
• If both sides of 3 A4 sheets are copied and stored to the document server, the C: count is 6 and the
L: count is 6.
• If you enter document server mode then scan 6 pages, the L: count is 6.
8221 [ADF Org Feeds]
These SPs count the number of pages fed through the ADF for front and back side scanning.
001 Front *CTL [0 to 99999999 / 0 / 1/step]
Number of front sides fed for scanning:
With an ADF that can scan both sides simultaneously, the Front side count is the same as the number of pages fed for either simplex or duplex scanning.
With an ADF that cannot scan both sides simultaneously, the Front side count is the same as the number of pages fed for duplex front side scanning. (The front side is determined by which side the user loads face up.)
002 Back *CTL [0 to 99999999 / 0 / 1/step]
Number of rear sides fed for scanning:
With an ADF that can scan both sides simultaneously, the Back count is the same as the number of pages fed for duplex scanning.
With an ADF that cannot scan both sides simultaneously, the Back count is the same as the number of pages fed for duplex rear-side scanning.
• When 1 sheet is fed for duplex scanning the Front count is 1 and the Back count is 1.
611
612
4. Controller SP Mode Tables
• If a jam occurs during the job, recovery processing is not counted to avoid double counting. Also, the pages are not counted if the jam occurs before the first sheet is output.
8231 [Scan PGS/Mode]
These SPs count the number of pages scanned by each ADF mode to determine the work load on the ADF.
001 Large Volume *CTL [0 to 99999999 / 0 / 1/step]
Selectable. Large copy jobs that cannot be loaded in the ADF at one time.
002 SADF *CTL [0 to 99999999 / 0 / 1/step]
Selectable. Feeding pages one by one through the ADF.
003 Mixed Size *CTL [0 to 99999999 / 0 / 1/step]
Selectable. Select "Mixed Sizes" on the operation panel.
004 Custom Size *CTL [0 to 99999999 / 0 / 1/step]
Selectable. Originals of non-standard size.
005 Platen *CTL [0 to 99999999 / 0 / 1/step]
Book mode. Raising the ADF and placing the original directly on the platen.
006 Mixed 1side/ 2side
Simplex and Duplex mode.
*CTL [0 to 99999999 / 0 / 1/step]
• If the scan mode is changed during the job, for example, if the user switches from ADF to Platen mode, the count is done for the last selected mode.
• The user cannot select mixed sizes or non-standard sizes with the fax application so if the original's page sizes are mixed or non-standard, these are not counted.
• If the user selects "Mixed Sizes" for copying in the platen mode, the Mixed Size count is enabled.
• In the SADF mode if the user copies 1 page in platen mode and then copies 2 pages with SADF, the Platen count is 1 and the SADF count is 3.
8241 [T:Scan PGS/Org] *CTL [0 to 99999999 / 0 / 1 / step
These SPs count the total number of scanned pages by original type for all jobs, regardless of which application was used.
Controller SP Tables - SP8000
8242
8243
8245
[C:Scan PGS/Org] *CTL [0 to 99999999 / 0 / 1 / step
These SPs count the number of pages scanned by original type for Copy jobs.
[F:Scan PGS/Org] *CTL [0 to 99999999 / 0 / 1 / step
These SPs count the number of pages scanned by original type for Fax jobs.
[S:Scan PGS/Org] *CTL [0 to 99999999 / 0 / 1 / step
8246
These SPs count the number of pages scanned by original type for Scan jobs.
[L:Scan PGS/Org] *CTL [0 to 99999999 / 0 / 1 / step
These SPs count the number of pages scanned and stored from within the document server mode screen at the operation panel, and with the Store File button from within the Copy mode screen
8241 8242 8243 8245 8246
001 Text
002 Text/Photo
003 Photo
004 GenCopy, Pale
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
005 Map
006 Normal/Detail
007 Fine/Super Fine
008 Binary
009 Grayscale
010 Color
011 Other
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
Yes
No
Yes
Yes
No
No
No
Yes
No
No
No
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
Yes
• If the scan mode is changed during the job, for example, if the user switches from ADF to Platen mode, the count is done for the last selected mode.
613
614
4. Controller SP Mode Tables
8251
8252
8255
8256
8257
[T:Scan PGS/ImgEdt]
[C:Scan PGS/ImgEdt]
[S:Scan PGS/ImgEdr]
[L:Scan PGS/ImgEdt]
[O:Scan PGS/ImgEdt]
*CTL These SPs show how many times Image Edit features have been selected at the operation
*CTL panel for each application. Some examples
*CTL of these editing features are:
Erase> Border
*CTL
Erase> Center
*CTL
Image Repeat
Centering
Positive/Negative
[0 to 99999999 / 0 / 1/step]
Note: The count totals the number of times the edit features have been used. A detailed breakdown of exactly which features have been used is not given.
The L: counter counts the number of pages stored from within the document server mode screen at the operation panel, and with the Store File button from within the Copy mode screen.
8261
8262
[T:Scan PGS/ColCr]
[C:Scan PGS/ ColCr]
8265 [S:Scn PGS/Color]
8266 [L:Scn PGS/ColCr]
These SPs show how many times color creation features have been selected at the operation panel.
001 Color Conversion *CTL [0 to 99999999 / 0 / 1/step]
002 Color Erase
003 Background
004 Other
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
Controller SP Tables - SP8000
8281
8285
8291
8293
8295
8301
8302
8303
8305
[T:Scan PGS/TWAIN]
[S:Scan PGS/TWAIN]
[T:Scan PGS/Stamp]
[F:Scan PGS/Stamp]
[S:Scan PGS/Stamp]
*CTL These SPs count the number of pages scanned using a TWAIN driver. These
*CTL counters reveal how the TWAIN driver is used for delivery functions.
[0 to 99999999 / 0 / 1/step]
Note: At the present time, these counters perform identical counts.
*CTL These SPs count the number of pages stamped with the stamp in the ADF unit.
*CTL
[0 to 99999999 / 0 / 1/step]
*CTL
The L: counter counts the number of pages stored from within the document server mode screen at the operation panel, and with the
Store File button from within the Copy mode screen
[T:Scan PGS/Size]
These SPs count by size the total number of pages scanned by all applications. Use these totals to compare original page size (scanning) and output (printing) page size [SP
8-441].
[C:Scan PGS/Size]
These SPs count by size the total number of pages scanned by the Copy application. Use these totals to compare original page size (scanning) and output (printing) page size [SP
8-442].
[F:Scan PGS/Size]
These SPs count by size the total number of pages scanned by the Fax application. Use these totals to compare original page size (scanning) and output page size [SP 8-443].
[S:Scan PGS/Size]
These SPs count by size the total number of pages scanned by the Scan application. Use these totals to compare original page size (scanning) and output page size [SP 8-445].
615
616
4. Controller SP Mode Tables
8306
001 A3
002 A4
003 A5
004 B4
[L:Scan PGS/Size]
These SPs count by size the total number of pages scanned and stored from within the document server mode screen at the operation panel, and with the Store File button from within the Copy mode screen. Use these totals to compare original page size (scanning) and output page size [SP 8-446].
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
005 B5
006 DLT
007 LG
008 LT
009 HLT
010 Full Bleed
254 Other (Standard)
255 Other (Custom)
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
8311
8315
T:Scan PGS/Rez *CTL [0 to 99999999/ 0 / 1]
These SPs count by resolution setting the total number of pages scanned by applications that can specify resolution settings.
S: Scan PGS/Rez *CTL [0 to 99999999/ 0 / 1]
These SPs count by resolution setting the total number of pages scanned by applications that can specify resolution settings.
Note: At the present time, SP8-311 and SP8-315 perform identical counts.
001 1200dpi <
002 600dpi to 1199dpi
003 400dpi to 599dpi
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
Controller SP Tables - SP8000
004 200dpi to 399dpi
005 < 199dpi
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
• Copy resolution settings are fixed so they are not counted.
• The Fax application does not allow finely-adjusted resolution settings so no count is done for the
Fax application.
8321
8322
[T:Sacn Poster]
[C:Sacn Poster]
8326 [L:Sacn Poster]]
001 2 Sheet
002 4 Sheet
003 9 Sheet
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
8381
8382
8383
8384
8385
8386
8387
[T:Total PrtPGS]
[C:Total PrtPGS]
[F:Total PrtPGS]
[P:Total PrtPGS]
[S:Total PrtPGS]
[L:Total PrtPGS]
[O:Total PrtPGS]
*CTL These SPs count the number of pages printed
*CTL by the customer. The counter for the application used for storing the pages
*CTL increments.
[0 to 99999999 / 0 / 1/step]
*CTL
*CTL
*CTL
*CTL
• When the A3/DLT double count function is switched on with SP5104, 1 A3/DLT page is counted as 2.
• When several documents are merged for a print job, the number of pages stored are counted for the application that stored them.
• These counters are used primarily to calculate charges on use of the machine, so the following pages are not counted as printed pages:
- Blank pages in a duplex printing job.
- Blank pages inserted as document covers, chapter title sheets, and slip sheets.
- Reports printed to confirm counts.
- All reports done in the service mode (service summaries, engine maintenance reports, etc.)
617
618
4. Controller SP Mode Tables
- Test prints for machine image adjustment.
- Error notification reports.
- Partially printed pages as the result of a copier jam.
8391 LSize PrtPGS *CTL [0 to 99999999 / 0 / 1/step]
These SPs count pages printed on paper sizes A3/DLT and larger.
Note: In addition to being displayed in the SMC Report, these counters are also displayed in the User Tools display on the copy machine.
001 A3/DLT, Larger
003 Bannaer Paper
8401
8402
8403
8404
8405
8406
[T:PrtPGS/LS]
[C:PrtPGS/LS]
[F:PrtPGS/LS]
[P:PrtPGS/LS]
[S:PrtPGS/LS]
[L:PrtPGS/LS]
*CTL These SPs count the number of pages printed from the document server. The counter for the
*CTL application used to print the pages is
*CTL
*CTL incremented.
The L: counter counts the number of jobs stored from within the document server mode
*CTL screen at the operation panel.
[0 to 99999999 / 0 / 1/step]
*CTL
• Print jobs done with Web Image Monitor and Desk Top Binder are added to the L: count.
• Fax jobs done with Web Image Monitor and Desk Top Binder are added to the F: count.
8411 Prints/Duplex *CTL This SP counts the amount of paper (front/ back counted as 1 page) used for duplex printing. Last pages printed only on one side are not counted.
[0 to 99999999 / 0 / 1]
8421
8422
[T:PrtPGS/Dup Comb]
These SPs count by binding and combine, and n-Up settings the number of pages processed for printing. This is the total for all applications.
[C:PrtPGS/Dup Comb]
These SPs count by binding and combine, and n-Up settings the number of pages processed for printing by the copier application.
Controller SP Tables - SP8000
8423
8424
8425
8426
[F:PrtPGS/Dup Comb]
These SPs count by binding and combine, and n-Up settings the number of pages processed for printing by the fax application.
[P:PrtPGS/Dup Comb]
These SPs count by binding and combine, and n-Up settings the number of pages processed for printing by the printer application.
[S:PrtPGS/Dup Comb]
These SPs count by binding and combine, and n-Up settings the number of pages processed for printing by the scanner application.
[L:PrtPGS/Dup Comb]
These SPs count by binding and combine, and n-Up settings the number of pages processed for printing from within the document server mode window at the operation panel.
8427 [O:PrtPGS/Dup Comb]
These SPs count by binding and combine, and n-Up settings the number of pages processed for printing by Other applications
001 Simplex> Duplex *CTL [0 to 99999999 / 0 / 1/step]
002 Duplex> Duplex
003 Book> Duplex
004 Simplex Combine
005 Duplex Combine
006 2in1
2 pages on 1 side (2-Up)
007 4 in1
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
4 pages on 1 side (4-Up)
008 6 in1
6 pages on 1 side (6-Up)
*CTL [0 to 99999999 / 0 / 1/step]
619
620
4. Controller SP Mode Tables
009 8 in1
8 pages on 1 side (8-Up)
010 9 in1
9 pages on 1 side (9-Up)
011 16 in1
16 pages on 1 side (16-Up)
012 Booklet
013 Magazine
014 2-in-1 + Booklet
015 4-in-1 + Booklet
016 6-in-1 + Booklet
017 8-in-1 + Booklet
018 9-in-1 + Booklet
019 2-in-1 + Magazine
020 4-in-1 + Magazine
021 6-in-1 + Magazine
022 8-in-1 + Magazine
023 9-in-1 + Magazine
024 16-in-1 + Magazine
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
• These counts (SP8 421 to SP8 427) are especially useful for customers who need to improve their compliance with ISO standards for the reduction of paper consumption.
• Pages that are only partially printed with the n-Up functions are counted as 1 page.
• Here is a summary of how the counters work for Booklet and Magazine modes:
Booklet
Original Pages
1
Count
1
Original Pages
1
Magazine
Count
1
Controller SP Tables - SP8000
Original Pages
2
3
4
5
6
7
8
Booklet
Count
2
2
2
3
4
4
4
Original Pages
2
3
4
5
6
7
8
Magazine
Count
2
2
2
4
4
4
4
8431
8432
8434
8436
8437
[T:PrtPGS/ImgEdt]
These SPs count the total number of pages output with the three features below, regardless of which application was used.
[C:PrtPGS/ImgEdt]
These SPs count the total number of pages output with the three features below with the copy application.
[P:PrtPGS/ImgEdt]
These SPs count the total number of pages output with the three features below with the print application.
[L:PrtPGS/ImgEdt]
These SPs count the total number of pages output from within the document server mode window at the operation panel with the three features below.
[O:PrtPGS/ImgEdt]
These SPs count the total number of pages output with the three features below with
Other applications.
001 Cover/Slip Sheet *CTL [0 to 99999999 / 0 / 1/step]
Total number of covers or slip sheets inserted. The count for a cover printed on both sides counts 2.
621
622
4. Controller SP Mode Tables
002 Series/Book *CTL [0 to 99999999 / 0 / 1/step]
The number of pages printed in series (one side) or printed as a book with booklet right/ left pagination.
003 User Stamp *CTL [0 to 99999999 / 0 / 1/step]
The number of pages printed where stamps were applied, including page numbering and date stamping.
8441
8442
8443
8444
8445
8446
[T:PrtPGS/Ppr Size]
These SPs count by print paper size the number of pages printed by all applications.
[C:PrtPGS/Ppr Size]
These SPs count by print paper size the number of pages printed by the copy application.
[F:PrtPGS/Ppr Size]
These SPs count by print paper size the number of pages printed by the fax application.
[P:PrtPGS/Ppr Size]
These SPs count by print paper size the number of pages printed by the printer application.
[S:PrtPGS/Ppr Size]
These SPs count by print paper size the number of pages printed by the scanner application.
[L:PrtPGS/Ppr Size]
These SPs count by print paper size the number of pages printed from within the document server mode window at the operation panel.
8447 [O:PrtPGS/Ppr Size]
These SPs count by print paper size the number of pages printed by Other applications.
001 A3
002 A4
003 A5
004 B4
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
Controller SP Tables - SP8000
005 B5
006 DLT
007 LG
008 LT
009 HLT
010 Full Bleed
254 Other (Standard)
255 Other (Custom)
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
• These counters do not distinguish between LEF and SEF.
8451 [PrtPGS/Ppr Tray]
These SPs count the number of sheets fed from each paper feed station.
001 Bypass Tray
002 Tray 1
003 Tray 2
*CTL Bypass Tray
[0 to 99999999 / 0 / 1/step]
*CTL Copier
*CTL
[0 to 99999999 / 0 / 1/step]
004 Tray 3
005 Tray 4
006 Tray 5
007 Tray 6
008 Tray 7
009 Tray 8
010 Tray 9
*CTL Paper Tray Unit (Option)
*CTL
[0 to 99999999 / 0 / 1/step]
*CTL Currently not used.
*CTL
*CTL
*CTL
*CTL
Currently not used.
Currently not used.
Currently not used.
Currently not used.
011 Tray 10
012 Tray 11
013 Tray 12
*CTL Currently not used.
*CTL Currently not used.
*CTL Currently not used.
623
624
4. Controller SP Mode Tables
014 Tray 13
015 Tray 14
016 Tray 15
*CTL Currently not used.
*CTL Currently not used.
*CTL Currently not used.
8461
8462
8463
[T:PrtPGS/Ppr Type]
These SPs count by paper type the number pages printed by all applications.
• These counters are not the same as the PM counter. The PM counter is based on feed timing to accurately measure the service life of the feed rollers. However, these counts are based on output timing.
• Blank sheets (covers, chapter covers, slip sheets) are also counted.
• During duplex printing, pages printed on both sides count as 1, and a page printed on one side counts as 1.
[C:PrtPGS/Ppr Type]
These SPs count by paper type the number pages printed by the copy application.
[F:PrtPGS/Ppr Type]
These SPs count by paper type the number pages printed by the fax application.
8464 [P:PrtPGS/Ppr Type]
These SPs count by paper type the number pages printed by the printer application.
8466 [L:PrtPGS/Ppr Type]
These SPs count by paper type the number pages printed from within the document server mode window at the operation panel.
001 Normal *CTL [0 to 99999999 / 0 / 1/step]
002 Recycled
003 Special
004 Thick
005 Normal (Back)
006 Thick (Back)
007 OHP
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
Controller SP Tables - SP8000
008 Other *CTL [0 to 99999999 / 0 / 1/step]
8491
8492
8493
8496
8497
8471 [PrtPGS/Mag]
These SPs count by magnification rate the number of pages printed.
001 < 49%
002 50% to 99%
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
003 100%
004 101% to 200%
005 201% <
*CTL
*CTL
*CTL
Counts are done for magnification adjusted for pages, not only on the operation panel but performed remotely with an external network application capable of performing magnification adjustment as well.
Magnification adjustments done with printer drivers with PC applications such as Excel are also counted.
Magnification adjustments done for adjustments after they have been stored on the document server are not counted.
Magnification adjustments performed automatically during Auto Reduce/Enlarge copying are counted.
The magnification rates of blank cover sheets, slip sheets, etc. are automatically assigned a rate of
100%.
8481
8484
[T:PrtPGS/TonSave] *CTL [0 to 99999999 / 0 / 1/step]
[P:PrtPGS/TonSave] *CTL
These SPs count the number of pages printed with the Toner Save feature switched on.
Note: These SPs return the same results as this SP is limited to the Print application.
[T:PrtPGS/Col Mode]
[C:PrtPGS/Col Mode]
[F:PrtPGS/Col Mode]
[L:PrtPGS/Col Mode]
[O:PrtPGS/Col Mode]
625
4. Controller SP Mode Tables
626
001 B/W
002 Single Color
003 Two Color
004 Full Color
051 B/W(Banner)
052 Single Color(Banner)
053 Two Color(Banner)
054 Full Color
*CTL These SPs count the number of pages printed in the Color Mode by each application.
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
8501
8504
8507
[T:PrtPGS/Col Mode]
[P:PrtPGS/Col Mode]
[O:PrtPGS/Col Mode]
001 B/W
002 Mono Color
003 Full Color
004 Single Color
005 Two Color
051 B/W(Banner)
052 Full Color(Banner)
053 Single Color(Banner)
054 Two Color(Banner)
*CTL These SPs count the number of pages printed in the Color Mode by the print application.
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
8511 [T:PrtPGS/Emul]
These SPs count by printer emulation mode the total number of pages printed.
8514 [P:PrtPGS/Emul]
These SPs count by printer emulation mode the total number of pages printed.
001 RPCS *CTL [0 to 99999999 / 0 / 1/step]
Controller SP Tables - SP8000
002 RPDL
003 PS3
004 R98
005 R16
006 GL/GL2
007 R55
008 RTIFF
009 PDF
010 PCL5e/5c
011 PCL XL
012 IPDL-C
013 BM-Links
014 Other
015 IPDS
016 XPS
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL Japan Only
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
• SP8 511 and SP8 514 return the same results as they are both limited to the Print application.
• Print jobs output to the document server are not counted.
8521
8522
8523
[T:PrtPGS/FIN]
These SPs count by finishing mode the total number of pages printed by all applications.
[C:PrtPGS/FIN]
These SPs count by finishing mode the total number of pages printed by the Copy application.
[F:PrtPGS/FIN]
These SPs count by finishing mode the total number of pages printed by the Fax application.
NOTE: Print finishing options for received faxes are currently not available.
627
628
4. Controller SP Mode Tables
8524
8525
8526
001 Sort
002 Stack
003 Staple
004 Booklet
005 Z-Fold
006 Punch
007 Other
008 Inside Fold
[P:PrtPGS/FIN]
These SPs count by finishing mode the total number of pages printed by the Print application.
[S:PrtPGS/FIN]
These SPs count by finishing mode the total number of pages printed by the Scanner application.
[L:PrtPGS/FIN]
These SPs count by finishing mode the total number of pages printed from within the document server mode window at the operation panel.
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
Half-Fold (FM2) (Multi Fold Unit)
009 Three-IN-Fold *CTL [0 to 99999999 / 0 / 1/step]
Letter Fold-in (FM4) (Multi Fold Unit)
010 Three-OUT-Fold *CTL [0 to 99999999 / 0 / 1/step]
Letter Fold-out (FM3) (Multi Fold Unit)
011 Four Fold *CTL [0 to 99999999 / 0 / 1/step]
Double Parallel Fold (FM5) (Multi Fold Unit)
012 KANNON-Fold
Gate Fold (FM6) (Multi Fold Unit)
*CTL [0 to 99999999 / 0 / 1/step]
Controller SP Tables - SP8000
013 Perfect-Bind
Perfect Binder
014 Ring-Bind
Ring Binder
015 3rd Vendor
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
• If stapling is selected for finishing and the stack is too large for stapling, the unstapled pages are still counted.
• The counts for staple finishing are based on output to the staple tray, so jam recoveries are counted.
8531 [Staple]
001 Staples
002 Stapless
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
8561
8562
8563
8564
8566
8567
8551
8552
8554
8556
[T:PrtBooks/FIN]
[C:PrtBooks/FIN]
[P:PrtBooks/FIN]
[L:PrtBooks/FIN]
001 Perfect-Bind
002 Ring-Bind
[T:A Sheet Of Paper]
[C:A Sheet Of Paper]
[F:A Sheet Of Paper]
[P:A Sheet Of Paper]
[L:A Sheet Of Paper]
[O:A Sheet Of Paper]
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
629
630
4. Controller SP Mode Tables
001 Total: Over A3/DLT
002 Total: Under A3/DLT
003 Duplex: Over A3/DLT
004 Duplex: Under A3/DLT
*CTL [0 to 99999999 / 0 / 1]
*CTL
*CTL
*CTL
8581 [T:Counter]
These SPs count the total output broken down by color output, regardless of the application used. In addition to being displayed in the SMC Report, these counters are also displayed in the User Tools display on the copy machine.
001 Total *CTL [0 to 99999999 / 0 / 1]
002 Total: Full Color
003 B&W/Single Color
004 Development: CMY
005 Development: K
008 Print: Color
009 Print: B/W
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
010 Total: Color
011 Total: B/W
012 Full Color: A3
013 Full Color: B4 JIS
014 Full Color Print
015 Mono Color Print
017 Twin Color Mode Print
018 Full Color Print (Twin)
019 Mono Color Print (Twin)
020 Full Color Total (CV)
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1]
Controller SP Tables - SP8000
021 Mono Color Total (CV)
022 Full Color Print (CV)
028 Development: CMY (A3)
029 Development: K (A3)
030 Total: Color (A3)
031 Total: B/W (A3)
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1]
8582 [C:Counter]
These SPs count the total output of the copy application broken down by color output.
001 B/W
002 Single Color
003 Two Color
004 Full Color
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1]
8583 [F:Counter]
These SPs count the total output of the fax application broken down by color output.
001 B/W *CTL [0 to 99999999 / 0 / 1]
002 Single Color *CTL
8584 [P:Counter]
These SPs count the total output of the print application broken down by color output.
001 B/W
002 Mono Color
*CTL [0 to 99999999 / 0 / 1]
*CTL
003 Full Color
004 Single Color
005 Two Color
*CTL
*CTL
*CTL
631
632
4. Controller SP Mode Tables
8586 [L:Counter]
These SPs count the total output of the local storage broken down by color output.
001 B/W *CTL [0 to 99999999 / 0 / 1]
002 Single Color
003 Two Color
004 Full Color
*CTL
*CTL
*CTL
8591 [O:Counter]
These SPs count the totals for A3/DLT paper use, number of duplex pages printed, and the number of staples used. These totals are for Other (O:) applications only.
001 A3/DLT
002 Duplex
003 Banner
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
8601 [T:Coverage Counter]
These SPs count the total coverage for each color and the total printout pages for each printing mode.
001 B/W
002 Color
*CTL [0 to 2147483647 / 0 / 1% / step]
*CTL
011 B/W Printing Pages
012 Color Printing Pages
021 Coverage Counter 1
022 Coverage Counter 2
023 Coverage Counter 3
031 Coverage Counter 1 (YMC)
032 Coverage Counter 2 (YMC)
033 Coverage Counter 3 (YMC)
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
Controller SP Tables - SP8000
8602 [C:Coverage Counter]
001 B/W
002 Single Color
003 Two Color
004 Full Color
8603 [F:Coverage Counter]
001 B/W
002 Single Color
*CTL
*CTL
*CTL
*CTL
[0 to 2147483647 / 0 / 1% / step]
*CTL [0 to 2147483647 / 0 / 1% / step]
*CTL
8604 [P:Coverage Counter]
001 B/W
002 Single Color
003 Two Color
004 Full Color
*CTL [0 to 2147483647 / 0 / 1% / step]
*CTL
*CTL
*CTL
8606 [L: Coverage Counter]
001 B/W
002 Single Color
003 Two Color
004 Full Color
8617
*CTL
*CTL
*CTL
*CTL
[0 to 2147483647 / 0 / 1% / step]
[SDK Apli Counter]
These SPs count the total printout pages for each SDK application.
633
634
4. Controller SP Mode Tables
001 SDK-1
002 SDK-2
003 SDK-3
004 SDK-4
005 SDK-5
006 SDK-6
007 SDK-7
008 SDK-8
009 SDK-9
010 SDK-10
011 SDK-11
012 SDK-12
8621 Func Use Counter
001 Function-001
002 Function-002
003 Function-003
004 Function-004
005 Function-005
006 Function-006
007 Function-007
008 Function-008
009 Function-009
010 Function-010
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL [0 to 99999999 / 0 / 1/step]
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL
*CTL
*CTL
*CTL
*CTL [0 to 99999999 / 0 / 1/step]
*CTL
*CTL
*CTL
*CTL
011 Function-011
012 Function-012
013 Function-013
014 Function-014
015 Function-015
016 Function-016
017 Function-017
018 Function-018
019 Function-019
020 Function-020
021 Function-021
022 Function-022
023 Function-023
024 Function-024
025 Function-025
026 Function-026
027 Function-027
028 Function-028
029 Function-029
030 Function-030
Controller SP Tables - SP8000
*CTL [0 to 99999999 / 0 / 1/step]
*CTL
*CTL
*CTL
*CTL
*CTL [0 to 99999999 / 0 / 1/step]
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL
*CTL
*CTL
*CTL
635
636
4. Controller SP Mode Tables
031 Function-031
032 Function-032
033 Function-033
034 Function-034
035 Function-035
036 Function-036
037 Function-037
038 Function-038
039 Function-039
040 Function-040
041 Function-041
042 Function-042
043 Function-043
044 Function-044
045 Function-045
046 Function-046
047 Function-047
048 Function-048
049 Function-049
050 Function-050
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL [0 to 99999999 / 0 / 1/step]
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL [0 to 99999999 / 0 / 1/step]
Controller SP Tables - SP8000
051 Function-051
052 Function-052
053 Function-053
054 Function-054
055 Function-055
056 Function-056
057 Function-057
058 Function-058
059 Function-059
060 Function-060
061 Function-061
062 Function-062
063 Function-063
064 Function-064
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL
*CTL
*CTL
8631 [T:FAX TX PGS]
These SPs count by color mode the number of pages sent by fax to a telephone number.
001 B/W
002 Color
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
8633 [F:FAX TX PGS]
These SPs count by color mode the number of pages sent by fax to a telephone number.
001 B/W
002 Color
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
• If a document has color and black-and-white pages mixed, the pages are counted separately as
B/W or Color.
637
638
4. Controller SP Mode Tables
• At the present time, this feature is provided for the Fax application only so SP8631 and SP8633 are the same.
• The counts include error pages.
• If a document is sent to more than one destination with a Group transmission, the count is done for each destination.
• Polling transmissions are counted but polling RX are not.
• Relay, memory, and confidential mailbox transmissions and are counted for each destination.
8641 [T:IFAX TX PGS]
These SPs count by color mode the number of pages sent by fax to as fax images using I-
Fax.
001 B/W *CTL [0 to 99999999 / 0 / 1/step]
002 Color *CTL [0 to 99999999 / 0 / 1/step]
8643 [F:IFAX TX PGS]
These SPs count by color mode the number of pages sent by Fax as fax images using I-
Fax.
001 B/W
002 Color
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
• If a document has color and black-and-white pages mixed, the pages are counted separately as
B/W or Color.
• At the present time, this feature is provided for the Fax application only so SP8641 and SP8643 are the same.
• The counts include error pages.
• If a document is sent to more than one destination with a Group transmission, the count is done for each destination.
• Polling transmissions are counted but polling RX are not.
• Relay, memory, and confidential mailbox transmissions and are counted for each destination.
8651 [T:S-to-Email PGS]
These SPs count by color mode the total number of pages attached to an e-mail for both the Scan and document server applications.
001 B/W *CTL [0 to 99999999 / 0 / 1/step]
Controller SP Tables - SP8000
002 Color *CTL [0 to 99999999 / 0 / 1/step]
8655 [S:S-to-Email PGS]
These SPs count by color mode the total number of pages attached to an e-mail for both the Scan and document server applications.
001 B/W *CTL [0 to 99999999 / 0 / 1/step]
002 Color *CTL [0 to 99999999 / 0 / 1/step]
• The count for B/W and Color pages is done after the document is stored on the HDD. If the job is cancelled before it is stored, the pages are not counted.
• If Scan-to-Email is used to send a 10-page document to 5 addresses, the count is 10 (the pages are sent to the same SMTP server together).
• If Scan-to-PC is used to send a 10-page document to 5 folders, the count is 50 (the document is sent to each destination of the SMB/FTP server).
• Due to restrictions on some devices, if Scan-to-Email is used to send a 10-page document to a large number of destinations, the count may be divided and counted separately. For example, if a
10-page document is sent to 200 addresses, the count is 10 for the first 100 destinations and the count is also 10 for the second 100 destinations, for a total of 20.).
8661 [T:Deliv PGS/Svr]
These SPs count by color mode the total number of pages sent to a Scan Router server by both Scan and LS applications.
001 B/W
002 Color
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
8665 [S:Deliv PGS/Svr]
These SPs count by color mode the total number of pages sent to a Scan Router server by the Scan application.
001 B/W
002 Color
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
639
4. Controller SP Mode Tables
640
• The B/W and Color counts are done after the document is stored on the HDD of the Scan Router server.
• If the job is canceled before storage on the Scan Router server finishes, the counts are not done.
• The count is executed even if regardless of confirmation of the arrival at the Scan Router server.
8671
8675
[T:Deliv PGS/PC]
These SPs count by color mode the total number of pages sent to a folder on a PC (Scanto-PC) with the Scan and LS applications.
[S: Deliv PGS/PC]
These SPs count by color mode the total number of pages sent with Scan-to-PC with the
Scan application.
001 B/W
002 Color
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step]
8681
8683
[T:PCFAX TXPGS]
[F:PCFAX TXPGS]
*CTL These SPs count the number of pages sent by
*CTL
PC Fax. These SPs are provided for the Fax application only, so the counts for SP8 681 and SP8 683 are the same.
[0 to 99999999 / 0 / 1/step]
8691
8692
8693
8694
8695
8696
• This counts pages sent from a PC using a PC fax application, from the PC through the copier to the destination.
• When sending the same message to more than one place using broadcasting, the pages are only counted once. (For example, a 10-page fax is sent to location A and location B. The counter goes up by 10, not 20.)
[T:TX PGS/LS]
[C:TX PGS/LS]
[F:TX PGS/LS]
[P:TX PGS/LS]
[S:TX PGS/LS]
[L:TX PGS/LS]
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
These SPs count the number of pages sent from the document server. The counter for the application that was used to store the pages is incremented.
[0 to 99999999 / 0 / 1/step]
The L: counter counts the number of pages stored from within the document server mode screen at the operation panel. Pages stored with the Store File button from within the
Copy mode screen go to the C: counter.
Controller SP Tables - SP8000
• Print jobs done with Web Image Monitor and Desk Top Binder are added to the count.
• If several documents are merged for sending, the number of pages stored are counted for the application that stored them.
• When several documents are sent by a Fax broadcast, the F: count is done for the number of pages sent to each destination.
8701 [TX PGS/Port]
These SPs count the number of pages sent by the physical port used to send them. For example, if a 3-page original is sent to 4 destinations via ISDN G4, the count for ISDN
(G3, G4) is 12.
001 PSTN-1 *CTL [0 to 99999999 / 0 / 1/step]
002 PSTN-2
003 PSTN-3
004 ISDN (G3,G4)
005 Network
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
8711
8715
[T:Scan PGS/Comp]
[S:Scan PGS/Comp]
These SPs count the number of pages sent by each compression mode.
001 JPEG/JPEG2000 *CTL [0 to 99999999 / 0 / 1/step]
002 TIFF(Multi/Single)
003 PDF
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
004 Other
005 PDF/Comp
006 PDF/A
007 PDF(OCR)
008 PDF/Comp(OCR)
009 PDF/A(OCR)
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
641
642
4. Controller SP Mode Tables
8721
8725
[T:Deliv PGS/WSD]
[S: Dvliv PGS/WSD]
These SPs count the number of pages scanned by each scanner mode.
001 B/W
002 Color
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
8731
8735
[T:Scan PGS/Media]
[S:Scan PGS/Media]
These SPs count the number of pages scanned and saved in a meia by each scanner mode.
001 B/W
002 Color
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
8741 [RX PGS/Port]
These SPs count the number of pages received by the physical port used to receive them.
001 PSTN-1
002 PSTN-2
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
003 PSTN-3
004 ISDN (G3,G4)
005 Network
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
8771 [Dev Counter]
These SPs count the frequency of use (number of rotations of the development rollers) for black and other color toners.
Controller SP Tables - SP8000
001 Total
002 K
003 Y
004 M
005 C
8781 [Toner_Botol_Info.]
001 BK
8791
002 Y
003 M
004 C
[LS Memory Remain]
*CTL
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
*CTL
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
This SP displays the percent of space available on the document server for storing documents.
[0 to 100 / 0 / 1%/step]
8801
001 K
002 Y
003 M
004 C
[Toner Remain]
These SPs display the percent of toner remaining for each color. This SP allows the user to check the toner supply at any time.
Note: This precise method of measuring remaining toner supply (1% steps) is better than other machines in the market that can only measure in increments of 10 (10% steps).
*CTL
*CTL
*CTL
*CTL
[0 to 100 / 0 / 1%/step]
8811
-
[Eco Counter]
643
644
4. Controller SP Mode Tables
001 Eco Total
002 Color
003 Full Color
004 Duplex
005 Combine
006 Color (%)
007 Full Color (%)
008 Duplex (%)
009 Combine (%)
010 Paper Cut (%)
051 Sync Eco Total
052 Sync Color
053 Sync Full Color
054 Sync Duplex
055 Sync Combine
056 Sync Color(%)
057 Sync Full Color(%)
058 Sync Duplex(%)
059 Sync Combine(%)
060 Sync Paper Cut(%)
101 Eco Totalr:Last
102 Color:Last
103 Full Color:Last
104 Duplex:Last
105 Combine:Last
*CTL [0 to 99999999 / 0 / 1/step]
*CTL
*CTL
*CTL
*CTL
*CTL [0 to 100 / 0 / 1% / step]
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 100 / 0 / 1% / step]
*CTL
*CTL
*CTL
*CTL
*CTL [0 to 99999999 / 0 / 1/step]
*CTL
*CTL
*CTL
*CTL
Controller SP Tables - SP8000
106 Color(%):Last
107 Full Color(%):Last
108 Duplex(%):Last
109 Combine(%):Last
110 Paper Cut(%):Last
151 Sync Eco Totalr:Last
152 Sync Color:Last
153 Sync Full Color:Last
154 Sync Duplex:Last
155 Sync Combine:Last
156 Sync Color(%):Last
157 Sync Full Color(%):Last
158 Sync Duplex(%):Last
159 Sync Combine(%):Last
160 Sync Paper Cut(%):Last
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[0 to 100 / 0 / 1% / step]
*CTL [0 to 99999999 / 0 / 1/step]
*CTL
*CTL [0 to 100 / 0 / 1% / step]
*CTL
*CTL
*CTL
*CTL
8851 [Cvr Cnt: 0-10%]
These SPs display the number of scanned sheets on which the coverage of each color is from 0% to 10%.
011 0 to 2%: BK
012 0 to 2%: Y
013 0 to 2%: M
014 0 to 2%: C
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1 / step]
645
646
4. Controller SP Mode Tables
021 3 to 4%: BK
022 3 to 4%: Y
023 3 to 4%: M
024 3 to 4%: C
031 5 to 7%: BK
032 5 to 7%: Y
033 5 to 7%: M
034 5 to 7%: C
041 8 to 10%: BK
042 8 to 10%: Y
043 8 to 10%: M
044 8 to 10%: C
*CTL [0 to 99999999 / 0 / 1 / step]
*CTL
*CTL
*CTL
*CTL [0 to 99999999 / 0 / 1 / step]
*CTL
*CTL
*CTL
*CTL [0 to 99999999 / 0 / 1 / step]
*CTL
*CTL
*CTL
8861
001 BK
002 Y
003 M
004 C
[Cvr Cnt: 11-20%]
These SPs display the number of scanned sheets on which the coverage of each color is from 11% to 20%.
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1 / step]
8871 [Cvr Cnt: 21-30%]
These SPs display the number of scanned sheets on which the coverage of each color is from 21% to 30%.
Controller SP Tables - SP8000
001 BK
002 Y
003 M
004 C
*CTL [0 to 99999999 / 0 / 1 / step]
*CTL
*CTL
*CTL
8881
001 BK
002 Y
003 M
004 C
[Cvr Cnt: 31%-]
These SPs display the number of scanned sheets on which the coverage of each color is
31% or higher.
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1 / step]
8891
001 BK
002 Y
003 M
004 C
[Page/Toner Bottle]
These SPs display the amount of the remaining current toner for each color.
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1 / step]
8901 [Page/Toner_Prev1]
These SPs display the amount of the remaining previous toner for each color.
001 BK
002 Y
003 M
004 C
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1 / step]
647
648
4. Controller SP Mode Tables
8911 [Page/Toner_Prev2]
These SPs display the amount of the remaining 2nd previous toner for each color.
001 BK *CTL [0 to 99999999 / 0 / 1 / step]
002 Y
003 M
004 C
*CTL
*CTL
*CTL
8921 [Cvr Cnt/Total]
Displays the total coverage and total printout number for each color.
001 Coverage (%) Bk
002 Coverage (%) Y
003 Coverage (%) M
004 Coverage (%) C
011 Coverage/P: Bk
*CTL
*CTL
*CTL
*CTL
*CTL
[0 to 2147483647 / 0 / 1% / step]
[0 to 99999999 / 0 / 1/step]
012 Coverage/P: Y
013 Coverage/P: M
014 Coverage/P: C
*CTL
*CTL
*CTL
8941 [Machine Status]
These SPs count the amount of time the machine spends in each operation mode. These
SPs are useful for customers who need to investigate machine operation for improvement in their compliance with ISO Standards.
001 Operation Time *CTL [0 to 99999999 / 0 / 1/step]
Engine operation time. Does not include time while controller is saving data to HDD
(while engine is not operating).
002 Standby Time *CTL [0 to 99999999 / 0 / 1/step]
Engine not operating. Includes time while controller saves data to HDD. Does not include time spent in Energy Save, Low Power, or Off modes.
Controller SP Tables - SP8000
003 Energy Save Time *CTL [0 to 99999999 / 0 / 10 / step]
Includes time while the machine is performing background printing.
004 Low Power Time *CTL [0 to 99999999 / 0 / 1/step]
Includes time in Energy Save mode with Engine on. Includes time while machine is performing background printing.
005 Off Mode Time *CTL [0 to 99999999 / 0 / 1/step]
Includes time while machine is performing background printing. Does not include time machine remains powered off with the power switches.
006 SC *CTL [0 to 99999999 / 0 / 1/step]
Total time when SC errors have been staying.
007 PrtJam *CTL [0 to 99999999 / 0 / 1/step]
Total time when paper jams have been staying during printing.
008 OrgJam *CTL [0 to 99999999 / 0 / 1/step]
Total time when original jams have been staying during scanning.
009 Supply PM Unit End *CTL [0 to 99999999 / 0 / 1/step]
Total time when toner end has been staying
8951 [AddBook Register]
These SPs count the number of events when the machine manages data registration.
001 User Code/User ID
User code registrations.
*CTL [0 to 99999999 / 0 / 1/step]
*CTL [0 to 99999999 / 0 / 1/step] 002 Mail Address
Mail address registrations.
003 Fax Destination
Fax destination registrations.
*CTL [0 to 99999999 / 0 / 1/step]
004 Group
Group destination registrations.
*CTL [0 to 99999999 / 0 / 1/step]
649
650
4. Controller SP Mode Tables
005 Transfer Request *CTL [0 to 99999999 / 0 / 1/step]
Fax relay destination registrations for relay TX.
006 F-Code *CTL [0 to 99999999 / 0 / 1/step]
F-Code box registrations.
007 Copy Program *CTL [0 to 255 / 0 / 255 / step]
Copy application registrations with the Program (job settings) feature.
008 Fax Program *CTL [0 to 255 / 0 / 255 / step]
Fax application registrations with the Program (job settings) feature.
009 Printer Program *CTL [0 to 255 / 0 / 255 / step]
Printer application registrations with the Program (job settings) feature.
010 Scanner Program *CTL [0 to 255 / 0 / 255 / step]
Scanner application registrations with the Program (job settings) feature.
8961 [Electricity Status]
-
001 Ctrl Standby Time
002 STR Time
003 Main Power Off Time
004 Reading and Printing Time
*CTL
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
Controller SP Tables - SP8000
005 Printing Time
006 Reading Time
007 Eng Waiting Time
008 Low Power State Time
009 Silent State Time
010 Heater Off State Time
011 LCD on Time
101 Silent Print
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
8971 [Unit Control]
-
001 Engine Off Recovery Count
002 Power Off Count
003 Force Power Off Count
*CTL
*CTL
*CTL
[0 to 99999999 / 0 / 1/step]
[0 to 99999999 / 0 / 1/step]
651
652
4. Controller SP Mode Tables
1001 [Bit Switch]
1-001-001 Bit Switch 1 bit 0 DFU bit 1 Responding with the hostname as the sysName
0
-
Model name
(PnP name)
This BitSwitch can change the value of the sysName.
0 (default): Model name (PnP name) such as "MP C401SP"
1: Host name bit 2 DFU bit 3 No I/O Timeout
-
Disabled
1
-
Hostname
-
Enabled
Enables/Disables MFP I/O Timeouts. If enabled, the MFP I/O Timeout setting will have no affect. I/O Timeouts will never occur.
bit 4 SD Card Save Mode Disabled Enabled
If this bit switch is enabled, print jobs will be saved to the GW SD slot and not output to paper.
bit 5 [PS and PDF] Paper size error margin ±5pt ±10pt
When a PS job is printed by using a custom paper size, the job might not be printed because of a paper size mismatch caused by a calculation error. By default, the error margin for matching to a paper size is ±5 points. By enabling this BitSwitch, the error margin for matching to a paper size can be extended to ±10 points.
Printer Service Menu bit 6 Color balance switching 0:Disabled 1:Enabled
This BitSwitch can be used to restore the color balance to match that of previous models. If this BitSwitch is set to "1" (Enabled), the color balance that is equivalent to Fuji-Xerox printers will be used.
bit 7 [RPCS,PCL]: Printable area frame border Disabled Enabled
Prints all RPCS and PCL jobs with a border around the printable area.
1001 [Bit Switch]
1-001-002 Bit Switch 2 bit 0
Color balance switching
0
Disabled
1
Enabled
This BitSwitch can be used to restore the color balance to match that of previous models. If this BitSwitch is set to "1" (Enabled), the color balance from 09S and earlier models will be used.
bit 1 DFU bit 2 Applying a Collate Type
-
Shift Collate
-
Normal
Collate
A collate type (shift or normal) will be applied to all jobs that do not explicitly define a collate type.
Note: If #5-0 is enabled, this BitSwitch has no effect.
bit 3 [PCL5e/c,PS]: PDL Auto Switching Enabled Disabled
Enables/Disables the MFPs ability to change the PDL processor mid-job.
Some host systems submit jobs that contain both PS and PCL5e/c. If Auto PDL switching is disabled, these jobs will not be printed properly.
653
654
4. Controller SP Mode Tables bit 4 Color balance switching bit 5
Disabled
This BitSwitch can be used to restore the color balance to match that of previous models. If this BitSwitch is set to "1" (Enabled), the color balance from 09A and Extended 09A models will be used.
DFU bit 6 Switch dither
-
Use normal dither
Enabled
-
Use alternative dither
*Please refer to RTB#RD014018 bit 7 DFU -
1001 [Bit Switch]
1-001-003 Bit Switch 3 bit 0 DFU bit 1 DFU
0
-
-
1
-
bit 2 [PCL5e/c]: Legacy HP compatibility Disabled Enabled
Uses the same left margin as older HP models such as HP4000/HP8000.
In other words, the left margin defined in the job (usually "<ESC>*r0A") will be changed to "<ESC>*r1A".
bit 3 DFU bit 4 DFU -
-
-
bit 5 DFU bit 6 DFU bit 7 DFU
-
-
-
-
-
-
1001 [Bit Switch]
Printer Service Menu
1-001-004 Bit Switch 4 bit 0 DFU bit 1 DFU
0
-
-
1
-
bit 2 DFU bit 3 IPDS print-side reversal
If enabled, the simplex pages of IPDS jobs will be printed on the front side because of printing on the back side of the page. This might reduce printing speed.
bit 4 DFU bit 5 bit 6
DFU
DFU bit 7 You can enable/disable the port for IPDS printing.
-
Disabled
-
-
Off
-
Enabled
-
-
On
1001 [Bit Switch]
655
656
4. Controller SP Mode Tables
1-001-005 Bit Switch 5 bit 0 Show "Collate Type", "Staple Type" and
"Punch Type" buttons on the operation panel.
0
Disabled
1
Enabled
If enabled, users will be able to configure a Collate Type, Staple Type, and
Punch Type from the operation panel. The available Types will depend on the device and configured options.
After enabling this BitSw, the settings will appear under:
"User Tools > Printer Features > System" bit 1 Multiple copies if a paper size or type mismatch occurs
Disabled
(single copy)
Enabled
(multiple)
If a paper size or type mismatch occurs during the printing of multiple copies, only a single copy is output by default. Using this BitSw, the device can be configured to print all copies even if a paper mismatch occurs.
bit 2 Prevent SDK applications from altering the contents of a job.
Disabled Enabled
If this BitSw is enabled, SDK applications will not be able to alter print data.
This is achieved by preventing SDK applications from accessing a module called the "GPS Filter".
Note: The main purpose of this BitSw is for troubleshooting the effects of SDK applications on data.
1001
Printer Service Menu bit 3 [PS] PS Criteria Pattern3 Pattern1
Change the number of PS criterion used by the PS interpreter to determine whether a job is PS data or not.
For details, refer to page 675 "Printing Features".
bit 4
Increase max. number of stored jobs.
Disabled
(100)
Enabled (750)
Changes the maximum number of jobs that can be stored on the HDD. The default (disabled) is 100. If this is enabled, the max. will be raised to 750 or
1000 depending on the model.
bit 5 DFU bit 6 Method for determining the image rotation for the edge to bind on.
Disabled Enabled
If enabled, the image rotation will be performed as they were in the specifications of older models for the binding of pages of mixed orientation jobs.
The old models are below:
- PCL: Pre-04A models
- PS/PDF/RPCS:Pre-05S models bit 7
Letterhead mode printing Disabled
Enabled
(Duplex)
Routes all pages through the duplex unit.
If this is disabled, simplex pages or the last page of an odd-paged duplex job, are not routed through the duplex unit. This could result in problems with letterhead/pre-printed pages.
Only affects pages specified as Letterhead paper.
[Bit Switch]
657
658
4. Controller SP Mode Tables
1-001-006 Bit Switch 6 bit 0 DFU bit 1 DFU bit 2 DFU bit 3 DFU bit 4 DFU bit 5 DFU bit 6 DFU bit 7 DFU
1001 [Bit Switch]
1-001-007 Bit Switch 7
Print path
0
Disabled
1
Enabled bit 0
If enabled, simplex pages (in mixed simplex/duplex PS/PCL5 jobs only) and the last page of an odd paged duplex job (PS, PCL5, PCL6), are always routed through the duplex unit. Not having to switch paper paths increases the print speed slightly.
bit 1 DFU bit 2 DFU bit 3 DFU bit 4 DFU bit 5 DFU bit 6 DFU bit 7 DFU -
-
-
-
-
-
-
-
-
-
-
-
1001 [Bit Switch]
-
-
-
-
-
-
0
-
-
-
-
-
-
-
-
1
-
-
Printer Service Menu
1-001-008 Bit Switch 8 bit 0 DFU bit 1 DFU
0
-
-
-
1
-
bit 2 bit 3
DFU
[PCL,PS]: Allow BW jobs to print without requiring User Code
Disabled
-
Enabled
(allow BW jobs to print without a user code)
BW jobs submitted without a user code will be printed even if usercode authentication is enabled.
Note: Color jobs will not be printed without a valid user code.
bit 4 DFU bit 5 DFU bit 6 PCL, RPCS, PS: Forced BW print
-
Enabled
-
Disabled bit 7
Switches whether to ignore PDL color command.
[PDF]: Orientation Auto Detect Function Enabled Disabled
Automatically chooses page orientations of PDF jobs (Landscape or Portrait) based on the content.
1001 [Bit Switch]
659
660
4. Controller SP Mode Tables
1-001-009 Bit Switch 9 bit 0
PDL Auto Detection timeout of jobs submitted via USB or Parallel Port (IEEE 1284).
0
Disabled
(Immediatel y)
1
Enabled
(10 seconds) bit 1
To be used if PDL auto-detection fails. A failure of PDL auto detection doesn't necessarily mean that the job can't be printed. This bit switch tells the device whether to time-out immediately (default) upon failure or to wait 10 seconds.
DFU bit 2 Job Cancel
-
Disabled
(Not cancelled)
Enabled
(Cancelled)
If this bit switch, all jobs will be cancelled after a jam occurs.
Note: If this bitsw is enabled, printing under the following conditions might result in problems:
- Job submission via USB or Parallel Port
- Spool printing (WIM >Configuration > Device Settings > System)
Printer Service Menu bit 3 PCL/PS bypass tray paper rotation (SEF/
LEF) bit 4 Timing of the PJL Status ReadBack (JOB
END) when printing multiple collated copies.
Disabled
This bitsw causes the device to revert to the behavior of previous generations.
It only takes effect if "Bypass Tray Setting Priority" = "Driver/Command".
Previous spec (bitsw=1): If a standard sized paper mismatch occurred in the bypass tray, the MFP always prompted for SEF paper.
If this bitsw=0 (default) then in the event of a standard sized paper mismatch, the MFP will always prompt for paper of the rotation (SEF/LEF) determined by the MFP bypass tray paper setting or by the bypass tray sensor.
Disable
Enabled
Enable
This bitsw determines the timing of the PJL USTATUS JOB END sent when multiple collated copies are being printed.
0 (default): JOB END is sent by the device to the client after the first copy has completed printing. This causes the page counter to be incremented after the first copy and then again at the end of the job.
1: JOB END is sent by the device to the client after the last copy has finished printing. This causes the page counter to be incremented at the end of each job.
661
662
4. Controller SP Mode Tables bit 5 Display UTF-8 text in the operation panel Enabled Disabled
Enabled (=0):
Text composed of UTF-8 characters can be displayed in the operation panel.
Disabled (=1):
UTF-8 characters cannot be displayed in the operation panel.
For example, job names are sometimes stored in the MIB using UTF-8 encoded characters. When these are displayed on the operation panel, they will be garbled unless this BitSw is enabled (=0).
bit 6 Disable super option bit 7 Enable/Disable Print from USB/SD's
Preview function
Enabled
Switches super option disable on / off. It this is On, multiple jobs are grouped at LPR port. PJL settings are enabled even jobs that are specified queue names are sent.
Enabled
Disabled
Disabled
Determines whether Print from USB/SD will have the Preview function.
Enabled (=0): Print from USB/SD will have the Preview function.
Disabled (=1): Print from USB/SD will not have the Preview function.
1001 [Bit Switch]
1-001-010 Bit Switch A bit 0 bit 1
DFU
DFU bit 2 DFU bit 3 DFU
0
-
-
-
bit 4 DFU bit 5 Store and Skip Errored Job locks the queue Queue is not locked after
SSEJ
-
Queue locked after SSEJ
If this is 1, then after a job is stored using Store and Skip Errored Job (SSEJ), new jobs cannot be added to the queue until the stored job has been completely printed.
1
-
-
-
-
1001
Printer Service Menu bit 6 Allow use of Store and Skip Errored Job if connected to an external charge device.
Does not allow SSEJ with ECD
Allows SSEJ with ECD
If this is 0, Store and Skip Errored Job (SSEJ) will be automatically disabled if an external charge device is connected.
Note: We do not officially support enabling this bitsw (1). Use it at your own risk.
bit 7 Job cancels remaining pages when the paidfor pages have been printed on an external charge device
Job does not cancel
Job cancels
When setting 1 is enabled, after printing the paid-for pages on an external charge device, the job that includes any remaining pages will be canceled.
This setting will prevent the next user from printing the unnecessary pages from the previous user's print job.
[Bit Switch]
663
664
4. Controller SP Mode Tables
1-001-011 Bit Switch B bit 0 Show Menu List
0
Hide Menu
List
1
Show Menu
List
If this is 0, the Menu List button will be removed from Printer Features.
bit 1 Print job interruption Does not allow interruption
Allow interruption
0 (default): Print jobs are not interrupted. If a job is promoted to the top of the print queue, it will wait for the currently printing job to finish.
1: If a job is promoted to the top of the queue, it will interrupt the currently printing job and start printing immediately.
bit 2 DFU bit 3 Not Used bit 4 DFU bit 5 DFU bit 6 DFU bit 7 DFU
-
-
-
-
-
-
-
-
-
-
-
-
1001 [Bit Switch]
Printer Service Menu
1-001-012 Bit Switch C bit 0 DFU bit 1 DFU
0
-
-
1
-
bit 2 DFU bit 3 DFU
-
-
-
bit 4 DFU bit 5 Change the user ID type displayed on the operation panel
-
Login User
Name
-
User ID
As of 15S models, the Login User Name can be displayed on the operation panel. The user ID type displayed on the operation panel can be changed by configuring BitSwitch #12-5 as follows:
- 0 (default): Login User Name
- 1: User ID. If this is enabled, User ID will be displayed, which is equivalent to the behavior exhibited in 14A and earlier models.
bit 6 Ability to use AirPrint Enabled Disabled
For 15S and later models that support AirPrint, AirPrint can be disabled by changing this Bit Switch from 0 (default) to 1.
bit 7 DFU -
1003 [Clear Setting]
1-003-001 Initialize System *CTL [- / - / -]
[Execute]
Initializes settings in the "System" menu of the user mode.
1-003-003 Delete Program *CTL [- / - / -]
[Execute]
1004 [Print Summary]
Prints the service summary sheet (a summary of all the controller settings).
1-004-001 Print Summary *CTL [- / - / -]
[Execute]
665
666
4. Controller SP Mode Tables
1-004-002 Print Summary2 *CTL [- / - / -]
[Execute]
1005 [Display Version]
1-005-002 Printer Version *CTL [ - / - / - ]
Displays the version of the controller firmware.
1006 [Sample / Proof Print]
1-006-001 Sample / Proof Print *CTL [0 or 1 / 1 / 1 /step]
0: Linked, 1: On
Enables and disables the document server. When you select "0," the document server is enabled or disabled in accordance with Copy Service Mode SP5-967. When you select "1," the document server is enabled regardless of Copy Service Mode
SP5-967.
1101 [Data Recall]
Recalls a set of gamma settings. This can be either a) the factory setting, b) the previous setting, or c) the current setting.
1-101-001 Factory
1-101-002 Previous
1-101-003 Current
1-101-004 ACC
*CTL
*CTL
*CTL
*CTL
[ - / - / - ]
[Execute]
1102 [Resolution Setting]
Selects the printing mode (resolution) for the printer gamma adjustment.
Printer Service Menu
1-102-001 Tone Control Mode
Selection
1103 [Test Page]
Prints the test page to check the color balance before and after the gamma adjustment.
1-103-001 Color Gray Scale
1-103-002 Color Pattern
CTL [ - / - / - ]
CTL
[Execute]
1104
CTL [0 to 9 / 0 / 1/step]
0: 1200x1200 Photo (2bit/4col)
1: 1200x1200 Photo (1bit/4col)
2: 600x600 Photo (4bit/4col)
3: 600x600 Photo (2bit/4col)
4: 600x600 Photo (1bit/4col)
5: 1200x1200 Text (2bit/4col)
6: 1200x1200 Text (1bit/4col)
7: 600x600 Text (4bit/4col)
8: 600x600 Text (2bit/4col)
9: 600x600 Text (1bit/4col)
[Gamma Adjustment]
Adjusts the printer gamma for the mode selected in the "Mode Selection" menu.
667
668
4. Controller SP Mode Tables
1-104-001 Black: Highlight
1-104-002 Black: Shadow
1-104-003 Black: Middle
1-104-004 Black: IDmax
1-104-021 Cyan: Highlight
1-104-022 Cyan: Shadow
1-104-023 Cyan: Middle
1-104-024 Cyan: IDmax
1-104-041 Magenta: Highlight
1-104-042 Magenta: Shadow
1-104-043 Magenta: Middle
1-104-044 Magenta: IDmax
1-104-061 Yellow: Highlight
1-104-062 Yellow: Shadow
1-104-063 Yellow: Middle
1-104-064 Yellow: IDmax
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL
CTL [0 to 30 / 00 / 1/step ]
CTL
CTL
1105 [Save Tone Control Value]
Stores the print gamma adjusted with the "Gamma Adj." menu item as the current setting. Before the machine stores the new "current setting", it moves the data currently stored as the "current setting" to the "previous setting" memory storage location.
1-105-001 Save Tone Control Value *CTL [ - / - / - ]
[Execute]
1106 [Toner Limit]
Adjusts the maximum toner amount for image development.
1-106-001 Toner Limit Value *CTL [0 to 400 / 0 / 1 %/step ]
Printer Service Menu
1110 [Media Print Device Setting]
Selects the setting for the media print device.
1-110-002 0: Disable 1: Enable *CTL [0 or 1 / 1 / 1/step]
1111
1-111-001 -
[All Job Delete Mode]
*CTL [ 0 or 1 / 0 / 1/step ]
0: Excluding New Job
1: Including New Job
Selects whether to include an image processing job in jobs subject to full cancellation from the SCS job list.
1113 [IBACC Exec]
Sets IBACC correction execution (calculation IBACC gamma) on / off.
0: Not calculate IBACC gamma. (Sets IBACC gamma linear)
1: Calculate IBACC gamma
1-113-001 0:Off 1:On *CTL [0 or 1 / 1 / 1/step]
1114 [IBACC ToneCtlSet]
Sets back to the previous value of IBACC gamma correction for all resolutions. If there is no previous value, sets to the factory default values.
1-114-001 Tone (Prev.)
1-114-002 Tone (Factory)
CTL -
CTL -
1115 [IBACC Exec Time]
Displays the time when IBACC is executed or sets back to the previous / initial value.
1-115-001 Time CTL -
669
670
4. Controller SP Mode Tables
1001
1-001-005 -
[Scan Nv Version]
*CTL [- / - / -]
1005 [Erase Margin(Remote scan)]
1-005-001 Range from 0 to 5 mm *CTL [0 to 5 / 0 / 1 mm/step]
1009
1-009-001 -
[Remote scan disable]
*CTL [0 or 1 / 0 / 1/step]
0: ON (enabled)
1: OFF (disabled)
1010
1-010-001 -
[Non Display Clear Light PDF]
*CTL [0 or 1 / 0 / 1/step]
0: Display, 1: No display
1011
1-011-001 -
[Org Count Display]
*CTL [0 or 1 / 0 / 1/step]
0: OFF (no display)
1: ON (count displays)
1012
1-012-001 -
[User Info Release]
*CTL [0 or 1 / 1 / 1/step]
1: Release
0: Do not release
1013 [Multi Media Function]
Scanner Service Menu
1-013-002 *CTL [0 or 1 / 1 / 1/step]
0: Disable
1: Enable
1014 [Scan to Folder Pass Input Set]
1-014-001 0: OFF 1: ON *CTL [0 or 1 / 0 / 1/step]
0: OFF
1: ON
1041 bit
[Scan:FlairAPI Setting]
1-041-001 0x00 – 0xff
Sets Scanner FlairAPI Function enable / disable.
This SP is set by BitSwitch and needs to reboot the machine after making changes.
Setting
*CTL * see BitSwitch below: meanings
Description
0 1 bit 0 bit 1
Start of FlairAPI Server Off
(Do not Start)
Access permission of
FlairAPI from outside of the machine
Disabled
On
(Start)
Sets whether to start exclusive
FlairAPI http server. If it is 0, scanning FlairAPI function and simple UI function will be disabled.
Enabled If it is “0”, accessing is limited from the machine only, such as operating panel, SDK/J, MFP browsers etc… If it is “1”, accessing is allowed from outside of FlairAPI such as PC,
Remote UI, IT-Box etc…
671
672
4. Controller SP Mode Tables bit 2 IPv6 (Exclusive) /
IPv4 (Priority)
Switching bit 3 bit 4 bit 5 bit 6 bit 7
Remote UI Function
Reserved
Reserved
Reserved
Reserved
-
-
-
-
IPv6
(Exclusive)
Not Used
-
-
-
-
IPv4
(Priority)
Use
-
-
-
If this bit is “0”, only IPv6 accessing is permitted.
If this bit is “1” and IPv4 is enabled, the machine uses IPv4 accessing. If this bit is “1” and
IPv4 is disabled, the machine uses IPv6 accessing. In this case, it is unable to access through Smart Operation Panel if IPv4 address is enabled.
-
Sets use of Remote UI for scanner function.
2021 [Compression Level (Gray-scale)]
2-021-001 Comp1:5-95 *CTL [5 to 95 / 20 / 1/step]
2-021-002 Comp2:5-95
2-021-003 Comp3:5-95
2-021-004 Comp4:5-95
2-021-005 Comp5:5-95
*CTL [5 to 95 / 40 / 1/step]
*CTL [5 to 95 / 65 / 1/step]
*CTL [5 to 95 / 80 / 1/step]
*CTL [5 to 95 / 95 / 1/step]
2023 [ACS setting of ClearLightPDF]
2-023-001 -
This SP code enables/disables the ACS function.
*CTL [0 or 1 / 1 / 1/step]
0: Disable
1: Enable
Scanner Service Menu
2024 [Compression ratio of ClearLight PDF]
2-024-001 Compression Ratio (Normal image)
*CTL [5 to 95 / 20 / 1/step]
2-024-002 Compression Ratio (High) *CTL [5 to 95 / 20 / 1/step]
2025 [Compression ratio of ClearLightPDF JPEG2000]
2-025-001 Compression Ratio
(Normal) JPEG2000
*CTL [5 to 95 / 20 / 1/step]
2-025-002 Compression Ratio (High)
JEPG2000
*CTL [5 to 95 / 20 / 1/step]
2030 [OCR PDF DetectSens]
2-030-001 Level5:
2-030-002 Level5:
2-030-003 Level5:
*CTL [0 to 255 / 250 / 1/step]
*CTL [0 to 100 / 80 / 1/step]
*CTL [0 to 100 / 80 / 1/step]
9001 [BitSwitch]
Sets module debug output mode.
9-001-001 cmm
9-001-002 jcm
*CTL [0 to 255 / 0 / by a factor of two]
*CTL [0 to 255 / 0 / by a factor of two]
9-001-003 ucm
9-001-004 rsp
9-001-005 rsp2
9-001-006 nas
9-001-007 miw
9-001-008 mib
9-001-009 itm
*CTL
*CTL
*CTL
*CTL
[0 to 255 / 0 / by a factor of two]
[0 to 255 / 0 / by a factor of two]
[0 to 255 / 0 / by a factor of two]
*CTL [0 to 255 / 0 / by a factor of two]
*CTL [0 to 255 / 0 / by a factor of two]
*CTL [0 to 255 / 0 / by a factor of two]
[0 to 255 / 0 / by a factor of two]
673
674
4. Controller SP Mode Tables
The auto PDL detection function gives the MFP the ability to determine the PDL of a job or of specific parts of a job. This can be especially useful in cases where the PDL is not specified or if the job contains multiple PDLs. This is only possible if the job was not created using a driver.
The MFP will only attempt to detect a job's PDL if all of the following conditions are met.
• No @PJL ENTER LANGUAGE command is contained in the job
• No submission protocol options (lpr, ftp, rcp, or rsh options) have been used to specify the PDL
• User Tools > Printer > System > Printer Language = Auto
• The printer is unable to detect PCL6 or RPCS. However these are almost always created using a driver and therefore contain the PJL command specifying the PDL.
There are 3 components in the printer which can perform Auto PDL Detection:
1. Printer system:
Uses a set of triggers unique to PCL5, PS or PDF. Up to 2KB from the start of the job can be searched for triggers.
2. PCL interpreter:
It can detect PS triggers in PCL data. If a PS trigger is detected, the PCL interpreter will abort processing and return the unprocessed part of the job back to the printer system. Up to 256 bytes from the start of each page can be searched for triggers.
3. PS interpreter:
It can detect PCL5 triggers in PS data. If a PCL trigger is detected, the PS interpreter will abort processing and return the unprocessed part of the job back to the printer system. The entire page
(regardless of the number of bytes) is searched for triggers.
675
676
5. Software Configuration
• 2. and 3. can be disabled using Printer Bit Switch 2-3=1.
• If the "Printer Language" is configured to anything other than Auto, all detection will be disabled.
• An interpreter submits a job page by page to the rasterizer. Therefore, when an interpreter detects a trigger mid-job, the previous pages will have already been submitted and will be output using the previously detected PDL.
• If the PDL cannot be detected by the printer system, then the PDL defaults to the one configured in
"Configuration > Printer Basic Settings > Default Printer Language".
The Printer Language setting and Default Printer Language setting in WIM:
Three types of PDL selection/switching are performed:
1. PDL selection (PCL5 or PS (including PDF)) at the beginning of the job: performed by the printer system
2. PDL switching from PCL5 to PS: performed by the PCL interpreter and the printer system
3. PDL switching from PS to PCL5: performed by the PS interpreter and the printer system
Printing Features
677
678
5. Software Configuration
Printer system
PCL5 triggers
PS triggers
PDF triggers
[ESC]E
[FF]
%!PS-Adobe-3.1
"%!"
"dict begin"
"bind def"
"findfont"
"showpage"
"/statusdict"
"0 startjob"
[EOT]
"}" + space character + "def"
"userdict" (*)
%PDF-
%!PS-Adobe-M.nPDF- (*M, n=numeric)
* "userdict" is excluded by configuring Printer Bit Switch 5-3=1.
• Up to 2KB from the start of the job can be searched for triggers.
• "%%" can be added to the PS triggers by configuring printer bit switch 5-3=1
• If a job is identified as PDF, it will be sent to the PS interpreter to be processed as a regular PS job.
PS interpreter
PCL5 trigger [ESC]E and 2 or more continuous PCL commands
• Up to 256 bytes from the start of each page can be searched for triggers.
Printing Features
Garbled output:
If a string of characters (or binary data) is mistaken as a trigger and an incorrect PDL is applied, the output will be garbled.
Incorrect printer settings:
Printer settings, for example the paper size, is incorrectly applied. This can happen when the printer settings at the beginning of the job are initialized before a PDL switch occurred and no settings were configured for the rest of the job.
Bit Switch 2-3
This controls auto PDL detection by the PCL interpreter and PS interpreter.
BitSW 2-3=0 (default):
If PDL switching is applied to the job, all of the printer system, PCL interpreter and PS interpreter will search for switching criteria (triggers).
BitSW 2-3=1:
Only the printer system will search for switching criteria (triggers). PCL/PS interpreters will not.
Bit Switch 5-3
This affects the PDL switching criteria (triggers) used by the printer system.
BitSW 5-3=0 (default):
"%%" is not used as a printer system PS trigger. "%%" will not call the PS interpreter.
BitSW 5-3=1:
"%%" is used as a printer system PS trigger.
The reason that "%%" is not included as a trigger by default, is that a string of text in the body of the job such as the following, could result in a false positive. This would trigger a switch and result in garbled output.
%%%%%%%%%%%%%%%%%%%%%%%%%%%
However some customers prefer that "%%" be included as a switching criteria. BitSW5-3=1 should be used in such a case.
• A side effect of BitSW5-3=1 is that "userdict" will no longer be used as a PS trigger.
Bit Switch 9-0
These determine whether Auto PDL Detection for print jobs transmitted via USB/parallel will wait 10 seconds to make sure the first 2KB of the job has been sent.
679
680
5. Software Configuration
The printer system portion of the auto PDL detection function is only performed on the first 2KB of a job and can wait up to 10 seconds for that first 2KB to arrive. As the printer is unable to detect the end of jobs submitted over a USB/Parallel connection, it might be preferable to not wait 10 seconds if jobs of less than 2KB are going to be printed. Enabling/disabling this waiting time is the purpose of BitSw 9-0.
BitSw 9-0=0 (default):
The printer system will not wait 10 seconds for the first 2KB of data to arrive.
BitSw 9-0=1:
The printer system will wait up to 10 seconds for the first 2KB of data to arrive.
Bit Switch 5-6
This change the way an MFP/LP rotates PCL, PS, PDF, or RPCS print images.
BitSW 5-6=0 (default):
A uniform binding edge (short or long edge) will be applied to every page of every job. Pages will always be rotated as if they were to be bound on that edge.
BitSW 5-6=1:
A uniform binding edge (short or long edge) will only be applied if the job is stapled, punched, or Zfolded. Otherwise, the bound edge might differ from page to page.
Example:
A 3-page job. Page 1 has the PCL simplex command. Page 2 and 3 have the PCL duplex long-edge bind commands.
No finishing options (staple, punch, z-fold) are used.
Printing Features
Bit Switch #5-6=0:
Bit Switch #5-6=1:
• Used in conjunction with Bit Switch #5-6, Orientation Auto Detect for PS/PDF jobs might cause unexpected results.
Bit Switch 9-4
These control the way PJL USTATUS returns page count totals in cases where multiple copies of a job are being printed.
BitSw 9-4=0 (default):
This change the way an MFP/LP rotates PCL, PS, PDF, or RPCS print images.
681
5. Software Configuration
682
1. The page count for a single copy is returned after the first copy is printed.
2. The page count for the rest of the copies, excluding the first copy, is returned after all copies have been printed.
3. This emulates an older HP PCL firmware spec. It is only needed for compatibility with legacy software.
BitSw 9-4=1:
The page count for all copies is output after all copies have been printed.
This emulates more recent HP PCL firmware specs.
For example, consider 3 copies of a 3 page job:
9-4 = 0
@PJL USTATUS JOB
START
NAME="TEST_page1-3"
@PJL USTATUS PAGE
1
@PJL USTATUS PAGE
2
@PJL USTATUS PAGE
3
@PJL USTATUS JOB
END
NAME="TEST_page1-3"
PAGES=3
<comment> The page count of the first copy is returned.</comment>
@PJL USTATUS PAGE
1
@PJL USTATUS PAGE
2
@PJL USTATUS PAGE
3
@PJL USTATUS PAGE
4
@PJL USTATUS PAGE
5
@PJL USTATUS PAGE
6
<comment> The page count of the remaining two copies is returned.</comment>
9-4 = 1
@PJL USTATUS JOB
START
NAME="Microsoft Word - TEST_page1-3"
@PJL USTATUS PAGE
1
@PJL USTATUS PAGE
2
@PJL USTATUS PAGE
3
@PJL USTATUS PAGE
4
@PJL USTATUS PAGE
5
@PJL USTATUS PAGE
6@PJL USTATUS PAGE
7
@PJL USTATUS PAGE
8
@PJL USTATUS PAGE
9
@PJL USTATUS JOB
END
NAME="Microsoft Word - TEST_page1-3"
PAGES=9
<comment> The page count of all three copies is returned.</comment>
Printing Features
683
5. Software Configuration
Configuring the scanner interface so that the most recently used scan destination is cleared.
Whether the MFP clears the most recently used scan destination, can be configured using Scanner SP
1-012-001.
By default, this is cleared to avoid subsequent users scanning to it by mistake.
Scanner SP 1-012-001
1 (default): Clear
0: Do not clear
This will cause all of the following to be cleared after the scanning is complete:
• Destination
• Sender
• Email subject
• Email message
• File name
Scanner SP 1-012-001=1 (default):
684
Exceptions:
• User Auth.:
If SP 1-012-001 = 0 and if User Auth. (excluding User Code authentication) is enabled, the most recently used scan destination will only be retained until the user logs out.
• Scanner Auto Reset timer:
Scanner Features
Even if SP 1-012-001 = 0 the most recently used scan destination can still be cleared by the
Scanner Auto Reset timer. If the Scanner Auto Reset timer is shorter than the System Auto Reset timer, then the most recently used scan destination will be cleared when the Scanner Auto Reset timer elapses.
Scan to Email fails with the error message "Transmission has failed ". The SMTP username and password are correct. How can I make Scan to Email pass ?
Change SP 5-860-022 "SMTP Auth. From Field Replacement" to On. By doing this, Scan to Email will pass the SMTP authentication.
• Using this option to solve the above problem, the device email address will appear in the email's
"From" field. The email address of the user who sent the email will appear in the "Reply-to" field.
Explanation
This is an SMTP authentication issue that aborts transmission of an already started Scan to Email.
Currently this has only been reproduced using MS-Exchange server.
MS-Exchange requires that all of the following match:
1. The sender's address in the "MAIL FROM" field. This is also known as the "envelope sender" or
"MIME sender". It is an SMTP command sent at the beginning of the email transmission process.
2. The sender's address in the mail header "From:" field. This appears as "From" in email clients. It is a part of the email itself.
3. The email address corresponding to the SMTP username used to login into the SMTP server.
When the MFP logins into the SMTP server, the email address of the username 3) will be compared to
1) and 2). If these comparisons fail, authentication will also fail. Exchange server will stop the transmission procedure, and the "Transmission has failed" message will be returned to the sender.
NG case:
SP5-860-022 is Off:
1. The "MAIL FROM" field = device (Fig.1 )
2. The mail header "From:" field = user (Fig.2 )
3. The SMTP username = device (Fig.1 )
When the SMTP server compares 2) and 3) the Exchange Server will stop the transmission procedure.
OK case:
SP5-860 can be used to make the values in the above example, match.
685
686
5. Software Configuration
In this example, if SP5-860-022 is On, the user's email address in the mail header '2)' will be replaced by the Administrator's email address. (see Fig.3 )
To solve the problem, the Administrator's address must be the same as the device's address.
If this is done:
1. The "Mail From: field = device (Fig.1 )
2. The mail header "From:" field = administrator (Fig.3 )
3. The SMTP username = device (Fig.1 )
1,2 and 3 must match and the authentication should be successful.
• The user's email address will still be inserted into the reply-to field.
Fig.1 Default device SMTP username, password and email address
Fig.2 A user's email address in the Address Book
Scanner Features
Fig.3 Administrator's email address
Determining which account Scan to Folder uses to access a scan destination and the effects of System SP
5-846-021.
This method depends on how the destination is accessed, whether authentication is being used, and SP
5-846-021.
Cases:
Case
A
B
C
Destination selection
Manual entry
User auth.
Either enabled or disabled
Account used to access the folder
The user's account *
Destination list disabled enabled
The recipient's account
(as configured in the Address Book's
Folder Authentication setting)
If SP 5-846-021 =
0 (default): The authenticated user's account
1: The recipient's account
(as configured in the Address Book's
Folder Authentication setting)
* The "user's account" will be either the one entered during scanning (see the Manual Entry screen capture) or if User Auth. is enabled, the account configured in the user's Folder Authentication setting will be used.
The desintation's access logs:
687
688
5. Software Configuration
Case A or Case C with SP=0: The access logs can be used to determine which user sent the scan.
Case B or Case C with SP=1: All access will be logged as the same user.
EN
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Advertisement
Print, copy, scan, and fax functions
Fast print speeds of up to 25 pages per minute
Large paper capacity of 2,300 sheets
User-friendly control panel
Advanced finishing options
The maximum paper capacity of the Ricoh MP C2504 series is 2,300 sheets.
The print speed of the Ricoh MP C2504 series is up to 25 pages per minute.
The Ricoh MP C2504 series offers a variety of advanced finishing options, including stapling, hole punching, and booklet making.
What does error code SC672 indicate, and what are the potential causes?
SC672 indicates a controller startup error. Potential causes include a defective controller board, wiring issues between the controller board and the operation panel, or a defective operation panel. The operation panel will not display anything when this error occurs.
What are the initial steps to troubleshoot an SC672 error, and how can the controller board's functionality be checked?
First, ensure the machine is properly connected to a working wall outlet. Then, turn the machine off and on using the main power switch and check if the fan near the controller board is running. Check the LED display on the controller board; if it's working normally, all LEDs should be lit.
Login to continue