C60T127A1 15/7/03 07:21 Página 1

INSTRUCTIONS MANUAL

FOR VITROCERAMIC HOBS

“TOUCH CONTROL”

H78TC

C60T127A1 15/7/03 07:21 Página 3

BET WITH US ON ECOLOGY. RECYCLE THE PACKAGING.

We contribute in the defence of the

Environment.

Thus, our packagins:

• Are 100% recyclable.

• Contain the smaller quantity of parts and possible material to facilitate thus the recycling.

3

C60T127A1 15/7/03 07:21 Página 4

CONTENTS

General description

.............................................................

5

Sensor description

.................................................................

6

Description of timer

...........................................................

7,8

Operating

.................................................................

9,10,11,12

Safety

..........................................................................................

13

Special considerations

.......................................................

13

Use of containers

..................................................................

14

Cleaning

..................................................................................

15

Connections schema

...........................................................

16

Installation

........................................................................

17,18

WARNING

• Repair of any fault in your hob must be carried out only by an

Authorized Repair Service, otherwise the guarantee is not valid.

• Technical details and identification of the appliance are shown on the specifications plate.

Consult this plate before procceding with electrical connection.

• Electrical connection must be carried out by a specialist familiar with the laws and official regulations recognized in each country.

Fill in the data table you will find below, with the data appearing on the specifications plate sticked on the hob.

Trade mark:

Pot.max: w

Type:

4

Voltage:

C60T127A1 15/7/03 07:21 Página 5

GENERAL DESCRIPTION

TYPE

VT7: PDFM-

1,2 kW

1,4kW

0,7kW

1,4kW

0.8kW

1,8 kW

Horizontal control sensors

5

C60T127A1 15/7/03 07:21 Página 6

SENSOR DESCRIPTION

HORIZONTAL CONTROL SENSORS

TYPE VT7:FPDM-

Control point

Sensor double heat zone

Control point

Sensor oval plate heat zone

Heat zone position indicators

Indicator display of selected power

Indicator display of residual heat

Heat zone power selection sensors from: 0....9

from: 9....0

Locking control point

Locking sensor

Sensor ON/OFF

6

C60T127A1 15/7/03 07:21 Página 7

DESCRIPTION OF TIMER

A timer, can be assigned to any heat source, and can be timed between 1 and

99 minutes. This timer will turn off the assigned heat zone once the time chosen by the user has passed.

7

C60T127A1 15/7/03 07:21 Página 8

DESCRIPTION OF TIMER

Assigning and Timing the Heat zone

To carry out the assignation of the timer to a heat zone the following steps must be followed:

With vitro ceramic hob switched on:

1- Choose the required power of the heat zone that you wish to time.

2- Switch on the timer. For this act once on the sensor + which corresponds to the timer. In the timer display appears and appears in the display of each heat zone.

3- Act on the + of the chosen heat zone.

will flash in the display corresponding to this heat zone. At this moment the timer is assigned to the chosen heat source.

4- Choose the desired time acting on the + which corresponds to the timer.

Once these steps have been carried out the assignation sequence of the heat zone timer ends.

The timer will automatically switch itself off, if between each step there is a time space of over 10 seconds or if you do not choose a length of time.

Once the timer has been assigned to a heat source and the time has been chosen, the timer will gradually discount the time and the display will indicate at each moment the time remaining to switch off the heat source.

During the timing, in the timed heat zone display you can see the selected power and the (indicating that this heat zone is timed) alternatively. Once the time has passed the heat zone will switch itself off, the control will release a warning acoustic signal and will flash in the timing display.

Acting on any sensor control the warning signal will stop.

Cancelling the timer

Act on the sensor of the timer until is shown on the minute display.

8

C60T127A1 15/7/03 07:21 Página 9

OPERATING

Sensors

The vitro-ceramic cooking surface is fitted with sensors that are touchsensitive and also react to the presence of a reflective object.

The hotplate is operated by touching the corresponding sensors with your fingers.

Take care to touch only one sensor at a time, otherwise they will not react to the touch.

Keep the sensors clean and do not place objects on them. The sensors may misinterpret dirt or objects placed on them as finger contacts.

Setting up

While the cooking surface is inoperative, the indicators for all sensors are switched off.

Starting up

Touch the ON/OFF sensor for 3 seconds. The power 0 displays will light up. If no power is selected within five seconds, the hotplate will automatically switch off and must be switched on again.

Power selection-/+

Each has - / + power sensors. Touching these allows the power to be set in the range 1 to 9.

To alter the power while the hotplate is on, touch - / + sensors to obtain the required power level.

9

C60T127A1 15/7/03 07:21 Página 10

OPERATING

Switching off the heat zone

Choose 0 power of the heat zone you wish to turn off. If the hotplate is hot, H will light up.

Residual heat display H

When activated but with level 0, the corresponding displays shows 0 and H alternatively.

While a hotplate is still hot but switched off, the display will show H.

Depending on the power that was used, this display may remain on for up to approximately 30 minutes.

Do not touch the area of the hotplate.

There is a risk of burning.

¡Warning!

If a power cut occurs while the residual heat display is on, remenber that when power is restrored the display will not re-appear even though the hotplate is still hot.

10

C60T127A1 15/7/03 07:21 Página 11

OPERATING

Hotplate blocking function

The blocking of the hotplates prevents accidental changes while they are operating. The initial selections are maintained and the indicators remain active. The hotplates should be blocked to prevent children from operating them or to prevent the effects of accidental contact with containers or tools.

Press the blocking sensor until its pilot light comes on.

Unblocking

Touch the blocking sensor until its pilot light switches off.

Double hotplate

Acting over the corresponding sensors of this heat zone only work with their small circuit . To operate the outer part, touch the double hotplate sensor until its pilot light comes on. To switch off touch the sensor until the pilot light switches off.

Oval hotplate

Oval hotplate acting over the corresponding sensors of this heat zone, only work with their circular circuit. To swicth on the outer part as well, touch the source hotplate sensor until its control point switches on.

To swicth off the oval hotplate, touch the oval hotplate sensor until the control point switches off.

11

C60T127A1 15/7/03 07:21 Página 12

OPERATING

Automatic programming 9

(quick heating)

Each control area includes an automatic programming function.

This programming allows the corresponding maximum temperature to be reached quickly and maintained automatically.

Selection

Touch sensor + once and it is in position 9, the corresponding decimal point to 9 will switch itself on.

Touching sensor – of the same zone will decrease to the required level

(levels 3…6 are recommended).

After having reached the automatic heating time a short signal will be heard and the decimal point will switch itself off. The heat zone goes on working in a conventional manner.

To cancel the automatic programming touch the - sensor and the decimal point will switch off.

12

C60T127A1 15/7/03 07:21 Página 13

SAFETY

Safety systems

In order to protect the electronics, if the control unit detects excessive heat it will switch off the hotplate closest to the sensors and the letter H will appear on the display. This hotplate can be activated when the temperature of the electronic unit returns to normal level.

Each hotplate is equiped with an interior temperature limiter that switches off the hotplate if the vitro-ceramic surface is heated excessively.

If any cracks appear on the vitro-ceramic surface, inmediately disconnect it from the mains. Do not use any part of the hob until a new vitro-ceramic surface has been fitted.

Automatic switch off

If a hotplate is left on accidentally, it will automatically be switched off after a period of time has passed, depending on the power level that has been selected (level 1 - 10 hours, level 9 - 1 hour).

SPECIAL CONSIDERATIONS

If more than one sensor is pressed simultaneously, the keys are blocked.

If all the power levels are at 0, the control is automatically switched off after

5 seconds.

If one or more sensors are pressed for more than 30 seconds (a container or tools is resting on the sensor), the control will automatically be switched off and a warning will sound every 30 seconds while the sensor remains pressed.

13

C60T127A1 15/7/03 07:21 Página 14

USE OF COOKING PANS

Most stainless steel, enamel, iron, ceramic and copper pans can be used on vitroceramic hobs.

YES

ALUMINIUM

Aluminium pans are not recommended as they may stain the vitreous surface, unless they have stainless-steel covered bottoms.

STAINLESS STEEL

ENAMEL

CERAMIC

COPPER

ALUMINIUM

SATINLESS STEEL

Hotplates should not be switched on without a pan on top. The base of the pan should be flat and dry.

Pans that have been used on gas cookers are not normally enough flat and absorb heat badly.

Make sure that the diameter of the pan is at least that of the hotplate.

Avoid scarping pans over the vitroceramic surface, as it may become scratched.

Always lift the pan.

Never use tinfoil or plastic containers.

They will melt and fuse permanently with the vitroceramic surface.

14

C60T127A1 15/7/03 07:21 Página 15

CLEANING

IMPORTANT: If the vitroceramic surface breaks or you notice cracks on it, disconnect the hob.

Call your Repair Service.

Clean the vitroceramic surface frequently, when it is cool. Never use abrasive products or pads. Clean with a damp cloth and soapy water.

Never use a steam cleaner.

Once a week, clean thoroughly with specific products that preserve and protect vitroceramic hobs (Sample in accessory bag). Scrape off hard stuck dirt with the scraper (Included in accessory bag).

The manufacturer recommends

VITRO-CLEN for cleaning and conserving your vitro-ceramic hob.

If sugar (or sugary matter) or plasttic is accidentally burnt on the hob, remove at once with the scraper while it is still hot. Otherwise they may leave a pemanent mark.

Do not use the hob as a work surface.

Be particularly careful with dirt like soil or dust from vegetables, cleaning powders, etc. which may scratch the surface when pans are slid over it.

15

INMEDIATELY

C60T127A1 15/7/03 07:21 Página 16

CONNECTIONS SCHEMA

If the type of connections to which the hotplate will be installed is other than

220 to 240 V AC remove the cable and make the connection according to the adjacent drawings. (The cable must support temperatures of up to 120ºC).

The hotplate must be connected to the mains with a plug that meets the EEC 7 publication or with a multi-pole switch with a distance between the open contacts of a least 3mm.

Total power

Hotplate: 75 cms., 7,4 kW

Three phase

PLATE

Voltage

Int.nominal

Protection by phases

Voltage

Int.nominal

Protection by phases

75 cms 220...240V~ 32 A 32 A 220...240V~ 16,5 A 20 A

Three phase

PLATE

Voltage

Int.nominal

Protection by phases

Voltage

Int.nominal

Protection by phases

75 cms 380...400V~ 13 A 16 A 380...400V~ 19 A 20 A

This device conforms to European directives 73/23/CEE and 89/336/CEE

16

C60T127A1 15/7/03 07:21 Página 17

INSTALLATION

1

Cut out a piece of the worktop following the instructions on the template that comes with the hob.

“X” type apparatus for degree of fire protection.

Minimum distance between hole and wall 100 m/m.

2

Place the hob face down on a table. Remove the backing paper and affix the sealing gasket all round the perimeter (fig.1).

When the plate comes with no frame, first stick on the shaped strips as per plan and then stick on the straight strips in a close fit with the others (fig.2).

fig.1

fig.2

NOTE: DO NOT USE NON-REMOVABLE ELEMENTS WITH SILICONE.

17

C60T127A1 15/7/03 07:21 Página 18

INSTALLATION

3

Place the hob alongside the cavity in the worktop and connect the power cable to the electrical socket.

IMPORTANT: Carry out connection with the power disconnected. There must be a good grounding connection and a switch must be provided in an accessible place to isolate all phases, with at least 3mm. clearance between contacts. The manufacturer will not accept responsability for installations carried out in a different way as informed here.

It is equipped with a power input cable for high temperatures.

If a new power input cable is required, installation should be performed by a technician certificated by the manufacturer. If the power feed wire is damaged, it must be replaced by the manufacturer, by the after-sales service or by authorized personnel for safety reasons.

4

Next insert the hob in the worktop cavity, pressing down firmly to ensure a good seal.

5

Fix the 4 clamps underneath the hob to the 4 corners of the cavity.

(Clamps, brackets and nuts supplied in acessory bag).

NOTE: This equipment complies with standard 82/499/CE on radio interferences.

18

C60T127A1 15/7/03 07:21 Página 19

C60T127A1 15/7/03 07:21 Página 20

Your 1 st Year Guarantee

Your appliance carries a 12 months parts and labour warranty. To fulfil the conditions of your guarantee, the appliance must be correctly installed and operated, in accordance with the instructions, and be only used for normal domestic purposes.

Please note that the guarantee, and service availability, only apply to the

United Kingdom.

Customer Service

In case of difficulty please call the Customer Service Helpline on

01245 321111

Please ensure you have the model and serial number to hand when calling customer service.

07-03

Printer on recycled paper

C60T127A1