advertisement
PRECAUTIONS
WARNING:
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPARATUS TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the apparatus’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the apparatus.
POWER SUPPLY
The main power supply is engaged when the main plug is plugged in a 220-240 V ~ , 50 Hz AC outlet. To operate the unit, press [ Q (standby-on)] to turn on the unit.
WARNING: LIVE PARTS INSIDE.
DO NOT REMOVE ANY SCREWS.
WARNING:
To prevent the spread of fire, keep candles or other open flames away from this product at all times
CAUTION
1) Do not attempt to open the cabinet. There are no user serviceable parts inside. Refer all servicing to qualified service personnel.
2) Slots and openings in the cabinet and the sides or bottom are provided for ventilation. To ensure reliable operation and to protect the unit from overheating, these openings must not be blocked or covered.
Avoid installation in enclosed spaces such as bookcases unless proper ventilation is provided.
3) Keep the unit away from radiators and other heat sources.
4) Do not push objects of any kind into the unit through the cabinet slots or openings as they could touch electrically live parts or short circuit parts resulting in a fire or electric shock.
5) To prevent fire or shock hazard, do not expose this unit to dripping or splashing, no objects filled with liquids, such as vases, should be placed on the unit.
6) Use the unit on a horizontal (flat) surface only.
7) Do not place any combustible objects on the unit
(candles, etc.).
8) The LCD panel used in this product is made of glass.
Therefore, it can break when the product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks.
The LCD panel is a very high technology product with
921,600 thin film transistors, giving you fine picture details. Occasionally, a few non-active pixels may appear on the TV screen as a fixed point of blue, green or red.
Please note that this does not affect the performance of your product.
9) Disconnect the mains plug to switch off when the unit becomes faulty or not in use.
10) The mains plug shall remain readily operable.
11) Read the manual instructions to ensure correct and safe installation and interconnection of the unit in multimedia systems.
12) Keep a distance of 20 cm around the ventilation openings of the unit.
13) Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.
Do not place the unit on the furniture that is capable of being tilted by a child or an adult leaning, pulling, standing or climbing on it. A falling unit can cause serious injury or even death.
EN
2
Off
TABLE OF CONTENTS
Features
• Integrated Digital Terrestrial Tuner (DVB-T)
• EPG (Electronic Programme Guide)
• Stereo Sound System
• On-Screen Display
• Sleep Timer
• Teletext
• TV Screen Mode Selection
• Auto Shut Off
• Parental Lock
• HDMI Input x 3, SCART x 2
• COMPONENT Input
• S-VIDEO Input
• PC Input
• Digital Audio Output
A Note about Recycling
This unit's packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.
This product consists of materials which can be recycled and reused if disassembled by a specialised company.
Following information is only for EU-member states:
The use of the symbol indicates that this product may not be treated as household waste.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Supplied Accessories
• Remote control
• Batteries (R6/AA) x 2
• Owner's Manual
• Phillips pan screw for attaching the stand x 4
Trademark Information
• Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
• HDMI, the HDMI Logo, and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
• DVB is a registered trademark of the DVB Project.
• The “HD TV” Logo is a trademark of DIGITALEUROPE.
Symbols Used in this Manual
The followings are the description for the symbols used in this manual.
DTV Digital TV operation
ATV Analogue TV operation
Following information is only valid EU-member States:
Disposal of batteries and/or accumulators
The crossed out wheeled dust bin symbol indicates that batteries and/or accumulators must be collected and disposed of separately from household waste.
If the battery or accumulator contains more than the specified values of lead (Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery Directive (2006/66/EC), then the chemical symbols for lead (Pb), mercury (Hg) and/or cadmium (Cd) will appear below the crossed out wheeled dust bin symbol.
By participating in separate collection of batteries, you will help to assure the proper disposal of products and batteries and thus help to prevent potential negative consequences for the environment and human health.
For more detailed information about the collection and recycling programmes available in your country, please contact your local city office or the shop where you purchased the product.
Pb, Hg, Cd
Model/Serial Number
To aid reporting in case of loss or theft, please record the unit’s model and serial numbers in the space provided. The numbers are located at the rear of the unit.
Model number: _________________
Serial number: _________________
3
EN
THINGS TO DO FOR THE FIRST TIME
ATTACHING THE STAND
You need to attach the stand to the unit to display upright. Make sure the front and rear of the stand match the proper direction.
1) Place the unit face down onto the soft stuff such as a cloth on a table. Be careful not to damage the unit screen. At least 2 people are required at this step.
2) Hang the hook under the bottom of the main unit to the stand’s hole (shown arrow A ), then slide down the stand in the direction of the screen (shown arrow B ).
Make sure not to put the AC power cord between the stand and the unit.
3) Drive Phillips pan screws in the 4 threaded holes at the bottom of the stand with a screwdriver tightly.
B front side
A
A
To remove the stand from this unit
Unscrew the Phillips pan screws indicated by “ C ”. Pull up the stand in the direction of the rear of the unit. Be careful not to drop the stand when you remove it.
Note: • When attaching the stand, make sure that all the screws are tightly fastened. If the stand is not attached properly, the unit may fall down, resulting in injuries as well as damage to the unit.
• Make sure to use the table which can support the weight and size of the unit.
• Make sure that the table is in a stable location.
Fixing the unit on the TV rack
Screw this unit on your TV rack tightly using wood screws
(not supplied) in the 2 holes at the back of the stand as shown.
Recommended screw dimension : 5.1 x 20 mm
Note: When you remove this unit from your TV rack, make sure to unscrew the wood screws.
Rear of this unit
C screw holes
EN
4
OPERATING CONTROLS AND FUNCTIONS
All operations described are based on the use of the remote control. Some operations can be carried out using the buttons on the control panel.
CONTROL PANEL REMOTE CONTROL
1
14
2
4 5 3 1
6 25
1.
Q (standby-on)
Press to turn on or off (standby) the unit.
2.
INPUT
Press to switch TV or external input mode.
3.
PROG.
K / L
(control panel)
Press to select the setting on the menu.
Press to select the item you want to adjust in the picture control mode.
Press to go to the next page or the previous page of teletext.
Same function as Cursor
K / L (remote control) on the menu.
PROG.
K / L (control panel) / / (remote control)
Press to select memorised channel or other modes.
4.
VOL.
X
/
Y
(control panel) / +/– (remote control)
Press to control the volume level.
VOL.
X
(control panel)
Same function as Cursor
B (remote control) on the menu.
VOL.
Y
(control panel)
Same function as Cursor s (remote control) on the menu.
5.
MENU
Press to display the menu.
6.
STAND BY / POWER indicator
Lights up in green when power is on.
Lights up in red when power is in standby mode.
7.
Number buttons
Press three digits to directly access the desired channel in TV mode.
Press to enter the password in the password input field.
8.
Cursor
K
/
L
/ s
/
B
buttons
Press to select the setting on the menu.
Press to select item you want to adjust in the picture control mode.
Press to go to the next page or the previous page of teletext.
9.
BACK
Press to return to the previous display.
10.
11.
(mute)
Press to mute the sound.
Press this button again or press VOL.
X / Y on the control panel or +/– on the remote control to restore sound.
(reveal)
Press to call up the hidden information of teletext.
7
5
8
9
ASPECT
15
16
17
18
19
4 3
10
11
12
13
20
21
22
23
24
12.
(text)
Press to display the teletext information.
13.
(subtitle)
Press to change the available subtitle languages.
14.
SLEEP
Press to set the sleep timer.
Press to hide the teletext.
15.
SOUND
Press to change the sound modes.
16.
ASPECT
Press to switch the aspect ratio available for the TV screen.
17.
GUIDE
Press to display EPG (Electronic Programme Guide) in digital mode.
18.
OK
Press to determine the setting on the menu.
Press to select or adjust from a particular menu.
Press to display the channel list while watching a programme.
19.
I (information)
Press to display the TV screen information.
20.
RED/GREEN/YELLOW/BLUE
Press to directly select the page numbers of teletext.
21.
22.
(expand)
Press to enlarge fonts of teletext.
(subpage)
Press to select subpages of teletext.
23.
(hold)
Press to hold the current page of teletext.
24.
(index)
Press to go back to the start page of teletext.
25.
Infrared sensor window
Receives the infrared rays transmitted from the remote control.
5
EN
REAR PANEL
30
37
27
*
38
39
35
36 34
33 31 32
28
26.
PC-IN (RGB) input jack
Connect a VGA cable (not supplied) to the monitor jack of a PC.
27.
HDMI (HDMI 1 / HDMI 2 / HDMI 3) input jack
Connect an HDMI cable (not supplied) to the HDMI output jack of an external device.
28.
COMPONENT (Y/Pb/Pr) / AUDIO (L/R) input jack
Connect an RCA component video and an RCA audio cable
(not supplied) to the component video and audio output jack of an external device.
29.
(Aerial) input jack
Connect an RF coaxial cable (not supplied) to an antenna or
RF output jack of a cable system.
30.
HEAD PHONE jack
Connect a headphone.
31.
VIDEO input jack
Connect an RCA video cable (not supplied) to the video output jack of an external device.
32.
AUDIO (L/R) input jack
Connect an RCA audio cable (not supplied) to the audio output jack of an external device.
Note: The AUDIO (L) jack is for monaural input. The sound is heard from both speakers. Use this jack for a monaural audio device.
33.
S-VIDEO input jack
Connect an S-Video cable (not supplied) to the S-Video output jack of an external device.
27 26 29
34.
PC-IN AUDIO input jack
Connect a mini-plug audio cable (not supplied) to the audio line out jack of a PC.
35.
SCART (SCART1 / SCART2) jack
Connect a scart cable (not supplied) to the scart jack of an external device.
36.
COAXIAL digital audio output jack
Coaxial digital cable connection for a decoder or an audio receiver.
37.
C.I. (Common Interface) slot
Common Interface (CI) Module: Insert the CI module.
38.
Cable management
Use this holder to bundle the cables.
39.
AC power cord
Connect to a standard AC outlet to supply power to this unit.
Note:
* service terminal (service use only)
• Use this terminal only when a software update is necessary.
• User should not connect any devices to the service terminal such as digital camera, keyboard, mouse, etc. (because these will not work).
• The software update is, in most cases, handled by an authorized service person or in some circumstances the user may be asked to do the software upgrade themselves.
EN
6
PREPARATION FOR USE
Installing the Batteries External Connection
1) Open the battery compartment cover.
2) Insert “R6/AA” penlight batteries into battery compartment in the direction as indicated by the polarity (+/–) markings.
Batteries installed with incorrect polarity may damage the remote unit.
3) Close the cover.
4) Push the cover on its top side until it clicks in order to fit the cover completely to the compartment.
[HDMI CONNECTION]
HDMI connection offers the highest picture quality. HDMI
(High Definition Multimedia Interface) transports high definition video and multi-channel digital audio through a single cable.
Connect the HDMI output jack of your video device and the
HDMI-IN (HDMI 1 or HDMI 2 or HDMI 3) jack of this unit.
Use an HDMI cable (not supplied).
HDMI cable
(not supplied)
Rear of this unit
Side of this unit
HDMI OUT or
To HDMI (HDMI 1 or HDMI 2 or HDMI 3) jack
Antenna Connection
UHF VHF
Dear Customer,
By connecting an HDMI cable to your Funai LCD TV, you have to use only a certified HDMI cable to guarantee a sufficient immunity against parasitic frequency radiation.
A certified HDMI cable can be identified by the HDMI logo on the cable or the cable package.
VHF/UHF
MIXER
RF cable (not supplied)
Rear of this unit
1) Connect an RF cable (not supplied) to (Aerial) input jack at the rear of this unit.
2) Plug this unit into an AC outlet.
3) The STAND BY / POWER indicator on the front panel lights red, then press
[ Q (standby-on)]
to turn on the unit.
Note: If you like to connect an active DVB-T antenna, the antenna must have its own power supply.
It is not possible to power the antenna from the TV.
Note: • This unit accepts 480i / 480p / 576i / 576p /
720p / 1080i / 1080p video signals and 32 kHz /
44.1 kHz / 48 kHz audio signals.
• This unit accepts only 2 channel audio signals
(LPCM).
• You need to select “PCM” for the digital audio output of the device you connect. Make sure the device outputs the digital audio. Audio sometimes makes no sound if you select “Bitstream”, etc.
[SCART CONNECTION]
Scart connection offers better picture quality.
Connect the scart jack of your video device and the SCART
(SCART1 or SCART2) jack of this unit. Use a scart cable (not supplied).
Rear of this unit
7 scart cable (not supplied)
Connector
S-VIDEO
INPUT
AUDIO
(L/R)
CVBS RGB
SCART 1
SCART 2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
OUTPUT
VIDEO and
AUDIO (L/R) only ATV or
DTV output is available.
output you can choose
EN
[COMPONENT CONNECTION]
RCA component video connection offers better picture quality.
1) Connect the component video output jack (Y, Pb, Pr) of your video device and the COMPONENT video (Y, Pb, Pr) input jack of this unit. Use an RCA component video cable (not supplied).
2) Connect the audio output jack of your device and the
AUDIO (L/R) input jack of this unit. Use an RCA audio cable (not supplied).
Rear of this unit
[VIDEO CONNECTION]
RCA video connection offers standard picture quality.
1) Connect the video output jack of your video device and the
VIDEO input jack of this unit. Use an RCA video cable (not supplied).
2) Connect the audio output jack of your video device and the
AUDIO (L/R) input jack of this unit. Use an RCA audio cable (not supplied).
Rear of this unit
COMPONENT
RCA component video cable
(not supplied)
RCA video cable
(not supplied)
RCA audio cable
(not supplied)
RCA audio cable
(not supplied)
VIDEO
OUT
AUDIO
OUT
Note: This unit accepts 480i / 480p / 576i / 576p / 720p /
1080i video signals.
[S-VIDEO CONNECTION]
S-Video connection offers good picture quality.
1) Connect the S-Video output jack of your video device and the S-VIDEO input jack of this unit. Use an S-Video cable
(not supplied).
2) Connect the audio output jack of your device and the
AUDIO (L/R) input jack of this unit. Use an RCA audio cable (not supplied).
Rear of this unit
S-VIDEO VIDEO
AUDIO
[AUDIO OUTPUT CONNECTION]
(for digital broadcasting only)
If you connect this unit and your external digital audio device, you can enjoy multi-channel audio like 5.1ch digital broadcasting sound.
Connect the COAXIAL input jack of your external digital audio devices and the COAXIAL output jack of this unit.
Use a digital audio coaxial cable (not supplied).
Rear of this unit digital audio coaxial cable
(not supplied)
S-Video cable
(not supplied)
RCA audio cable
(not supplied)
S-VIDEO
OUT
VIDEO
OUT
AUDIO
OUT
Note: If you connect to the S-VIDEO jack and the VIDEO jack at the same time, S-Video connection will have priority.
EN
8
DIGITAL AUDIO
COAXIAL IN
[PC CONNECTION]
If you connect this unit and your PC, you can use this unit as a computer monitor.
1) Connect the monitor jack of your PC and the PC-IN (RGB) jack of this unit. Use a VGA cable with ferrite core (not supplied).
2) Connect the audio line out jack of your PC and the PC-IN
(AUDIO) jack of this unit. Use a mini-plug audio cable (not supplied).
Cable Management
Keep the cables through this holder to avoid tangle them.
Rear of this unit mini-plug audio cable
(not supplied)
To audio line out jack
IAL
PC-IN
AUDIO
Rear of this unit
To monitor jack
VGA cable with ferrite core
(not supplied)
To PC-IN jack
Precautions for the connection to other devices:
• Please use the VGA cable that has a ferrite core.
The following signals can be displayed:
Format
VGA
SVGA
XGA
WXGA
Resolution
640 x 480
800 x 600
1,024 x 768
1,280 x 768
1,360 x 768
Refresh rate
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
Note: Other formats or non-standard signals will not be displayed correctly.
9
EN
SETUP FOR USE
Initial Setting
DTV ATV
You need to set the followings to use the unit appropriately for the first time you turn on the unit.
1) Press [ Q (standby-on)] to turn on the unit.
• “Initial Setup” language menu will appear.
Note: The settings may be limited by the location you purchased.
2) Press [
K
/
L
] repeatedly to select the menu language you want, then press [OK] .
Initial Setup
Please select language:
Select
Language
Next
Ȼɴɥɝɚɪɫɤɢ
ýHVN\
Dansk
Deutsch
ǼȜȜȘȞȚțȐ
English
Español
BACK
Exit
3) Press [
K
/
L
] to select the country you want, then press
[OK] .
Initial Setup
Please select country:
Country
Austria
Belgium
Czech Republic
France
Germany
Hungary
Italy
Back Select Next
• Scan confirmation menu will appear.
BACK
Exit
4) Press
[
K
/
L
]
to select “Scan”, then press
[OK]
.
• Channel scanning will start automatically.
Scan Initial Setup
Now the system is scanning for channels, please wait.
Auto Scan will take up to 10 minutes to complete.
Scanning
Analogue:
Digital: 3
0
30%
BACK
Cancel
• When the scanning is completed “Congratulations !!” message will appear.
Note: • If you select “Skip” in scan confirmation menu, the operation will be cancelled.
• If you press
[BACK]
during auto scanning, the operation will be cancelled.
EN
10
OPERATIONS
Watching a TV Programme
DTV ATV
To select a channel
Press
[
/
]
repeatedly to select your desired channel.
or
Press
[the Number buttons]
to enter a channel number then
[OK] for quicker access.
• If you want to select the channel 24 without pressing [OK] , press
[2]
first, then press
[4]
within 3 seconds.
To adjust the volume
Press [ +/–] to adjust the audio volume.
• You can see the volume bar while adjusting the volume.
Switching the Input Mode
DTV ATV
You can switch the input mode to TV mode or external input mode.
1) Press [INPUT] .
• “Select Input” menu will appear.
Select Input
TV
VIDEO
COMPONENT
SCART 1
SCART 2
PC
HDMI 1
HDMI 2
HDMI 3
Sleep Timer
Volume 30
Press [ (mute)] to turn on or off the sound right away.
• You can recover the original volume by pressing [ (mute)] again or
[ +/–]
.
DTV ATV
You can set the unit to be turned off automatically after a set time period (from 10 to 120 minutes).
1) Press [SLEEP] .
• Sleep timer display will appear.
2) Press
[SLEEP]
repeatedly to change the sleep time period.
• Between Off and 60 minutes, the interval of time is 10 minutes. After 60 minutes, the timer increases by 30 minutes until Off.
2) Press
[
K
/
L
]
to select the input mode you want, then press
[OK]
.
Note: • To watch TV, select “TV”.
• To use the video or S-VIDEO input jack on the unit, select “VIDEO”.
• To use the COMPONENT (Y/Pb/Pr) input jack on the unit, select “COMPONENT”.
• To use the SCART (SCART1) jack on the unit, select
“SCART 1”.
• To use the SCART (SCART2) jack on the unit, select
“SCART 2”.
• To use the PC-IN (RGB) jack on the unit, select “PC”.
• To use the HDMI-IN (HDMI 1) jack on the unit, select “HDMI 1”.
• To use the HDMI-IN (HDMI 2) jack on the unit, select “HDMI 2”.
• To use the HDMI-IN (HDMI 3) jack on the unit, select “HDMI 3”.
Sleep 10 min.
To cancel the sleep timer
1) Press [SLEEP] .
• Sleep timer display will appear.
2) Press [SLEEP] repeatedly until “Sleep Off ” appears.
Sleep Off
Note:
If you disconnect the unit from the AC outlet or if a power failure occurs, the sleep timer will be cancelled.
11
EN
Sound Select TV Screen Information
DTV
1) Press [SOUND] to display the currently selected audio language and the number of available languages.
2) Press
[SOUND]
repeatedly to cycle through the available audio languages.
• The display image can be found on the “TV Screen
Information” at the right column.
no icon
Dolby Digital sound
Dolby Digital Plus sound
HE-AAC sound
MPEG sound
ATV
1) Press [SOUND] to display the currently selected audio mode.
2) Press [SOUND] repeatedly to cycle through the available audio mode.
• The display image can be found on the “TV Screen
Information” at the right column.
1.
Nicam Stereo Mono
2.
Nicam Dual1 Nicam Dual2 Mono
3.
4.
5.
6.
Nicam Mono
Stereo
Dual1
Mono
Mono
DTV ATV
You can see the broadcasting information.
1) Press [ I (information)] .
• Fewer information menu will appear.
2) Press
[ I (information)]
again to display more informations.
ETV 09:37
Hit Music 07:00-09:59
You're turned to the Sounds, keep it here for the biggest sounds around, it doesn't get fresher than this! Call
09012 345 678 now to select a video
18
1080i HD 16:9
English 1/3
English
1 Channel name
2 Present programme name / time
3 Programme information
4 Current time
5 Channel number
6 Resolution / Format / TV aspect ratio
7 Audio language (DTV) / Audio mode (ATV)
8 Subtitle
9 TV / Radio
10 Lock status
11 Parental rating
12 Pay TV
13 Teletext
14 Audio Description
Note: When the programme information consists of more than
3 lines, press
[
K
/
L
]
to scroll.
3) Press [BACK] to exit.
• TV Screen information menu will automatically disappear in a few seconds.
EN
12
EPG (Electronic Programme Guide)
DTV
You can easily find a channel or see the detailed channel information. EPG gives you scheduled information of the TV programmes.
1) Press [GUIDE] .
• EPG will appear.
Television TV guide
Viewing date: Thu ,04 Oct
18
19
20
21
22
ETV
Euro CH
Drama Now!
WNS
BCT
19:00
20:00
22:00
22:50
23:00
Current time: Thu ,04 Oct 21:16:27
Hit Music
Special
Our Home
Pick Up Number
The Frying Winem
19:00 - 20:00 Music
Prev page Next page
2) Press
[
K
/
L
]
to select a channel, then press
[
B
]
.
• Press [RED] or [GREEN] to move the channel list to the previous or next page.
• Press
[OK]
to watch the selected channel.
3) Press
[
K
/
L
]
to select a programme.
• Press [RED] or [GREEN] to move the programme list to the previous or next day.
• Press
[OK]
to watch the selected programme if it is currently available.
4) Press [YELLOW] to display more detailed programme information.
Television TV guide Detail
20:00-22:00 Euro CH
BB Special: Mr.Smith introduces unseen items from previous programmes in the series and talks to expect Mrs. Cole about the history of BB House.
1/1
Music
Prev page Next page Return
Note: When the programme information consists of more than
2 pages, press [RED] or [GREEN] to move to the previous or next page.
5) Press [GUIDE] to exit.
13
EN
Changing the TV Screen Display Mode
DTV ATV
You can select your favourite TV screen size.
Press [ASPECT] repeatedly to switch the TV screen display mode.
For SD (Standard Definition) video signal
“Sidebar”
For HD (High Definition) video signal
“Auto”
“Expand”
“Full”
“Zoom”
“Auto”
“Cinema”
“14:9” “Full”
“Wide” “Cinema”
“Auto”
Selects the TV screen display mode automatically.
This is the default.
“Sidebar”
Displays a 4:3 picture at its original size. Sidebars appear on both edge of the TV screen.
“Full”
Displays a 4:3 picture at a 16:9 size; the picture is stretched horizontally to fill the TV screen.
“Cinema”
Displays a 4:3 picture at a 16:9 size; the picture is stretched horizontally and vertically to fill the TV screen. This crops out the top and bottom of the picture.
“Wide”
Displays a 4:3 picture at a 16:9 size; the centre of the picture is at its original size and the edges stretched horizontally to fill the TV screen.
“14:9”
Displays a 4:3 picture at a 14:9 size. Sidebars will be displayed on both edge of the TV screen.
“Auto”
Selects the TV screen display mode automatically.
This is the default.
“Full”
Displays a 16:9 picture at its original size.
“Zoom”
Displays a 16:9 picture at its maximum size without changing its horizontal and vertical ratio.
“Cinema”
Displays a vertically stretched picture.
“Expand”
Displays a horizontally stretched picture.
For PC input signal
“Normal”
“Dot by Dot”
“Full”
“Normal”
Displays a proportionally stretched picture. Mainly sidebars appear on both edges of the TV screen.
“Full”
Displays a picture that is stretched out of proportion to fill the TV screen.
“Dot by Dot”
Displays a picture at its original size.
EN
14
OTHER SETTINGS
Picture Adjustment
DTV ATV
You can adjust the picture settings according to your personal preference. These settings are automatically stored after exiting the picture menu.
1) Press
[MENU]
to display the menu.
2) Press [
K
/
L
] to select “Picture”, then press [OK] .
“Picture Mode”
3) Press [
K
/
L
] to select “Picture Mode”.
4) Press
[ s
/
B
]
to select the setting (“Standard, Dynamic,
Movie, News, Personal”) you want.
Picture
Sound
TV
Setup
Parental
Picture
Picture Mode
Brightness
Contrast
Colour
Hue
Sharpness
Colour Temperature
Features
Standard
Normal
50
75
50
0
4
Select
BACK
Back
“Colour Temperature”
3) Press [
K
/
L
] to select “Colour Temperature”.
4) Press
[ s
/
B
]
to select the setting (“Cool, Normal, Warm”) you want.
Standard Picture
Sound
TV
Setup
Parental
Picture
Picture Mode
Brightness
Contrast
Colour
Hue
Sharpness
Colour Temperature
Features
Normal
Select
BACK
Back
50
75
50
0
4
5) Press [MENU] to exit.
“Brightness, Contrast, Colour, Hue, Sharpness”
3) Press [
K
/
L
] to select the item you want, then press [OK] .
Note: Press
[
K
/
L
]
to change the items.
4) Press [ s
/
B
] to adjust, then press [OK] .
Note: • When this unit is connected to PC, you can not select
“Colour”, “Hue” and “Sharpness”.
• If you adjust the settings in other than “Personal” mode, “Picture Mode” will be changed to “Personal”.
Brightness
Brightness
Contrast
Contrast
Colour
Colour
Hue
Hue
Sharpness
Sharpness
Setting
0
4
75
50
50
[ s
] decrease brightness decrease contrast decrease colour add red make soft
[
B
] increase brightness increase contrast increase colour add green make clear
15
EN
Advanced Picture Adjustment
DTV ATV
You can adjust the detailed picture settings according to your personal preference.
1) Press
[MENU]
to display the menu.
2) Press [
K
/
L
] to select “Picture”, then press [OK] .
3) Press
[
K
/
L
]
to select “Features”, then press
[OK]
.
• “Features” menu will appear.
Picture
Sound
TV
Setup
Parental
Features
DNR
CTI
Flesh Tone
Adaptive Luma Control
Backlight
Mid
Mid
On
On
100
Select
BACK
Back
“Flesh Tone”
You can set to activate the flesh colours or not.
4) Press
[
K
/
L
]
to select “Flesh Tone”.
5) Press [ s
/
B
] to select the setting (“On, Off ”) you want.
“Adaptive Luma Control”
You can adjust changes in the luminance of the picture.
4) Press [
K
/
L
] to select “Adaptive Luma Control”.
5)
5)
Press
Press
[
[ s s
/
“Backlight”
/
B
B
]
]
to select the setting (“On, Off ”) you want.
4) Press
[
K
/
L
]
to select “Backlight”, then press
[OK]
.
to adjust, then press
Backlight
“DNR (Digital Noise Reduction)”
You can adjust to reduce the appearance of digitizing error caused by the compression.
4) Press [
K
/
L
] to select “DNR”.
5) Press [ s
/
B
] to select the setting (“Low, Mid, High”) you want.
“CTI (Colour Transient Intensity)”
You can adjust the picture for colour errors.
4) Press [
K
/
L
] to select “CTI”.
5) Press
[ s
/
B
]
to select the setting (“Low, Mid, High”) you want.
6) Press [MENU] to exit.
[OK] .
100
EN
16
PC Settings
You can adjust the PC screen position, clock and phase. Make sure your PC is connected.
1) Press [MENU] to display the menu.
2) Press
[
K
/
L
]
to select “Picture”, then press
[OK]
.
3) Press [
K
/
L
] to select “PC Settings”, then press [OK] .
“Auto Adjustment”
4) Press [
K
/
L
] to select “Auto Adjustment”, then press [OK] .
Picture
Sound
Setup
Parental
Auto Adjustment
H.Position
V.Position
Phase
Clock
60
50
18
130
Sound Adjustment
DTV ATV
You can adjust the sound settings according to your personal preferences. These settings are automatically stored after exiting the sound menu.
1) Press [MENU] to display the menu.
2) Press
[
K
/
L
]
to select “Sound”, then press
[OK]
.
• “Sound” menu will appear.
Picture
Sound
TV
Setup
Parental
Sound
Balance
Bass
Treble
Virtual Surround Sound
Sound Mode
Digital Audio Output
Auto Volume Control
Assistive Services
Visually Impaired
Off
Standard
PCM
Off
-
Adjust Select
BACK
Back
0
50
50
PC Settings Enter Select
BACK
Back
• Each setting will be adjusted automatically.
“H.Position, V.Position, Phase, Clock”
4) Press [
K
/
L
] to select the item you want, then press [OK] .
Note: Press [
K
/
L
] to change the items.
5) Press [ s
/
B
] to adjust, then press [OK] .
H.Position
H.Position
V.Position
Phase
V.Position
Phase
Clock
Clock
Setting
6) Press
[MENU]
to exit.
60
50
[ s
] move PC screen left move PC screen down
[
B
] move PC screen right move PC screen up
18 decrease setting value increase setting value
130
“Balance, Bass, Treble”
3) Press [
K
/
L
] to select the item you want, then press [OK] .
Note: Press [
K
/
L
] to change the items.
4) Press [ s
/
B
] to adjust, them press [OK] .
[ s
] [
B
]
Balance
Balance
Bass
Bass
Treble
Treble
Setting
0
50
50 decrease increase
“Virtual Surround Sound”
Virtual Surround Sound gives you the stereo phonic virtual space through your existing 2-channel stereo system.
3) Press
[
K
/
L
]
to select “Virtual Surround Sound”.
4) Press [ s
/
B
] to select the setting (“On, Off ”) you want.
“Sound Mode”
3) Press [
K
/
L
] to select “Sound Mode”.
4) Press
[ s
/
B
]
to select the setting (“Standard, Movie, Music,
News”) you want.
17
EN
“Digital Audio Output”
You can set the audio output to “Auto” or “PCM”.
3) Press
[
K
/
L
]
to select “Digital Audio Output”.
4) Press [ s
/
B
] to select the setting (“Auto, PCM”) you want.
Auto : Dolby Digital (if available)
PCM : PCM
“Auto Volume Control”
You can set to keep a constant loudness differential between the
TV commercials and the programs.
3) Press [
K
/
L
] to select “Auto Volume Control”.
4) Press [ s
/
B
] to select the setting (“On, Off ”) you want.
“Assistive Services”
DTV
You can adjust the audio type.
3) Press [
K
/
L
] to select “Assistive Services”.
4) Press
[ s
/
B
]
to select the setting (“-, Hearing Impaired,
Visually Impaired”) you want.
Visually Impaired : provides additional audio description for visually impaired.
Hearing Impaired : provides audio service for hearing impaired.
Note: If you select “Visually Impaired”, you can adjust the audio volume for “Visually Impaired”.
5) Press
[MENU]
to exit.
“Visually Impaired”
DTV
Make sure “Visually Impaired” is selected at “Assistive Services” setting.
3) Press
[
K
/
L
]
to select “Visually Impaired” then press
[OK]
.
4) Press [
K
/
L
] to select “Volume” then press [OK] .
5) Press
[ s
/
B
]
to adjust, then press
[OK]
.
Country Setting
Note: You may not select the country depending on the location you purchased.
DTV ATV
You can select the channels according to the country you select.
1) Press [MENU] to display the menu.
2) Press
[
K
/
L
]
to select “TV”, then press
[OK]
.
3) Press [
K
/
L
] to select “Country”.
4) Press
[ s
/
B
]
to select the country you want.
DTV
ATV
TV
Picture
Sound
TV
Setup
Parental
Country
Audio Language
Audio Language 2nd
Channel
France
English
English
Select
BACK
Back
TV
Picture
Sound
TV
Setup
Parental
Country
Audio Channel
Channel
5) Press [MENU] to exit.
France
Stereo
Select
BACK
Back
20 Volume
6) Press
[MENU]
to exit.
EN
18
Audio Language Selection
DTV ATV
You can select the main language.
1) Press [MENU] to display the menu.
2) Press
[
K
/
L
]
to select “TV”, then press
[OK]
.
DTV
“Audio Language”
3) Press [
K
/
L
] to select “Audio Language”.
4) Press [ s
/
B
] to select the language you want.
TV
Picture
Sound
TV
Setup
Parental
Country
Audio Language
Audio Language 2nd
Channel
France
English
English
Select
BACK
Back
“Audio Language 2nd”
3) Press [
K
/
L
] to select “Audio Language 2nd”.
4) Press
[ s
/
B
]
to select the language you want.
Picture
Sound
TV
Setup
Parental
Country
Audio Language
Audio Language 2nd
Channel
France
English
English
TV Select
BACK
Back
5) Press [MENU] to exit.
Note: While watching a programme, you can change the audio language easily using [SOUND] when it is available.
Auto Scan
DTV ATV
You can scan the channels receivable in your area automatically.
1) Press [MENU] to display the menu.
2) Press
[
K
/
L
]
to select “TV”, then press
[OK]
.
3) Press [
K
/
L
] to select “Channel”, then press [OK] .
4) Press
[
K
/
L
]
to select “Auto Scan”, then press
[OK]
.
• Scanning will start automatically.
Picture
Sound
TV
Setup
Parental
Auto Scan
Scanning
Analogue: 1
Digital: 8
60%
BACK
Cancel
• When the scanning is completed, “Scan Completed” message will appear.
• If you press [MENU] during the scanning, this operation will be stopped and the lowest memorised digital channel will be displayed.
• Please note that after tuning, the analogue channels will be stored in the order that they are broadcast by your local transmitter. This may not be in the same order in which you would like them to be stored. If this is the case, you can change the order according to your preference. To do this,
see “Channel Sort” on page 21.
ATV
“Audio Channel”
3) Press [
K
/
L
] to select “Audio Channel”.
4) Press
[ s
/
B
]
to select the setting (“Dual1, Dual2, Stereo,
Mono”) you want.
Picture
Sound
TV
Setup
Country
Audio Channel
Channel
France
Stereo
Parental
TV Select
BACK
Back
Note: While watching a programme, you can change the audio mode easily using [SOUND] when it is available.
19
EN
Analogue Manual Scan Update Scan
ATV
You can adjust an analogue channel individually.
1) Press [MENU] to display the menu.
2) Press
[
K
/
L
]
to select “TV”, then press
[OK]
.
3) Press [
K
/
L
] to select “Channel”, then press [OK] .
4) Press
[
K
/
L
]
to select “Manual Scan (Analogue)”, then press
[OK]
.
5) Press [the Number buttons] to enter the frequency.
• To select 24, enter [0] first, then press [2] and [4] .
6) Press [
K
/
L
] to select “Scan Up” or “Scan Down”, then press
[OK]
.
• Scanning will start automatically.
Picture
Sound
TV
Scanning (Analogue)
Setup
Parental
Start Frequency (MHz)
Scan Up
Scan Down
Manual Scan (Analogue)
45.00
BACK
Back
DTV ATV
You can scan the updated channels automatically.
1) Press [MENU] to display the menu.
2) Press
[
K
/
L
]
to select “TV”, then press
[OK]
.
3) Press [
K
/
L
] to select “Channel”, then press [OK] .
4) Press
[
K
/
L
]
to select “Update Scan”, then press
[OK]
.
• Scanning will start automatically.
Picture
Sound
TV
Setup
Parental
Update Scan
Scanning
Analogue:
Digital: 8
1
60%
BACK
Cancel
• When this scanning is completed, “Scan Completed” message will appear.
5) Press
[MENU]
to exit.
• When this scanning is completed, “Scan Completed” message will appear.
7) Press
[MENU]
to exit.
Single RF Scan
DTV
You can adjust a digital channel individually.
1) Press [MENU] to display the menu.
2) Press [
K
/
L
] to select “TV”, then press [OK] .
3) Press [
K
/
L
] to select “Channel”, then press [OK] .
4) Press
[
K
/
L
]
to select “Single RF Scan”, then press
[OK]
.
5) Press [ s
/
B
] to select the channel number you want to scan, then press [OK] .
• Scanning will start automatically.
Picture
Sound
TV
Scanning (Digital)
Setup
Parental
Single RF Scan
Channel
Signal Strength
21
0%
60
Search
BACK
Back
• When this scanning is completed, “Scan Completed” message will appear.
6) Press [MENU] to exit.
Channel List
DTV ATV
You can easily find a channel you want.
1) Press [OK] while watching a programme.
• “Channel List” will appear.
Channel List
18 ETV
19 Euro CH
20 Drama Now!
21 WNS
22 BCT
25 Starcast
38 Eurasia Station
Page up Page down no icon
ATV
Digital radio service
DTV
2) Press [
K
/
L
] to select the channel you want to watch.
• Press [RED] or [GREEN] to move to the previous or next page.
• Press [OK] to watch the selected programme if it is currently available.
3) Press [BACK] to exit.
Note:
You can edit the channel list. Refer to page 21 to page
EN
20
Channel Skip Channel Sort
DTV
When using
[
ATV
/
]
, the channel you selected will be skipped.
1) Press [MENU] to display the menu.
2) Press [
K
/
L
] to select “TV”, then press [OK] .
3) Press
[
K
/
L
]
to select “Channel”, then press
[OK]
.
4) Press [
K
/
L
] to select “Channel Skip”, then press [OK] .
• “Channel List” will appear.
5) Press [
K
/
L
] to select the channel you want to skip, then press [OK] .
• “ ”will appear on the right of the channel.
Picture
Sound
TV
Setup
Parental
Channel Skip
18
19
20
21
22
38
901
902
Digital
Digital
Digital
Digital
Digital
Digital
Analogue
Analogue
Set
ETV
Euro CH
Drama Now!
WNS
BCT
Eurasia Station
-----
-----
Select
BACK
Back
6) Press [MENU] to exit.
If you want to cancel
5) Press
[
K
/
L
]
to select the channel set to be skipped, then press
[OK]
.
• “ ”will disappear.
6) Press [MENU] to exit.
DTV ATV
You can change the channel order.
1) Press [MENU] to display the menu.
2) Press
[
K
/
L
]
to select “TV”, then press
[OK]
.
3) Press [
K
/
L
] to select “Channel”, then press [OK] .
4) Press
[
K
/
L
]
to select “Channel Sort”, then press
[OK]
.
• “Channel List” will appear.
5) Press [
K
/
L
] to select the channel you want to move, then press [OK] .
• “
✔
” will appear on the right of the channel.
Picture
Sound
TV
Setup
Parental
Channel Sort
18
19
Digital
Digital
20
21
22
38
Digital
Digital
Digital
901
902
Digital
Analogue
Analogue
Set
ETV
Euro CH
Drama Now!
WNS
BCT
Eurasia Station
-----
-----
Select
BACK
Back
6) Press [
K
/
L
] to select the channel you want to switch, then press [OK] .
• The channel order will be changed.
7) Press [MENU] to exit.
21
EN
Channel Edit
DTV ATV
You can edit channel information.
1) Press [MENU] to display the menu.
2) Press
[
K
/
L
]
to select “TV”, then press
[OK]
.
3) Press [
K
/
L
] to select “Channel”, then press [OK] .
4) Press
[
K
/
L
]
to select “Channel Edit”, then press
[OK]
.
• “Channel List” will appear.
Picture
Sound
TV
Setup
Parental
Channel Edit
18
19
20
21
22
38
901
902
Digital
Digital
Digital
Digital
Digital
Digital
Analogue
Analogue
Enter
ETV
Euro CH
Drama Now!
WNS
BCT
Eurasia Station
-----
-----
Select
BACK
Back
5) Press
[
K
/
L
]
to select the channel you want to edit, then press
[OK]
.
6) Press [
K
/
L
] to select your desired item.
Picture
Sound
TV
Setup
Parental
Channel Edit
Channel Number:
Name:
Frequency:
Colour System
Sound System
Set
802
TVE I
77.3
Auto
D/K
Select
BACK
Back
“Channel Number”
7) Press [the Number buttons] to enter a channel number you want, then press [OK] .
“Name”
7) Press
[the Number buttons]
to enter a channel name you want, then press
[OK]
.
(Refer to the following character table.)
“Frequency”
7)
8)
ATV
7) Press [the Number buttons] to enter a frequency you want, then press [OK] .
“Colour System , Sound System”
ATV
Press
Press
[ s
/
B
]
[MENU]
to select the setting you want.
to exit.
Channel Decode
ATV
Some TV stations transmit encoded TV signals which can only be viewed with a purchased or hired decoder. You can connect such a decoder to SCART jack of the unit. This function will automatically activate the connected decoder for the channel.
1) Press [MENU] to display the menu.
2) Press
[
K
/
L
]
to select “TV”, then press
[OK]
.
3) Press [
K
/
L
] to select “Channel”, then press [OK] .
4) Press
[
K
/
L
]
to select “Channel Decode”, then press
[OK]
.
• “Channel List” will appear.
5) Press [
K
/
L
] to select the channel you want to allocate the decoder, then press [OK] .
• “ ”will appear on the right of the channel.
Picture
Sound
TV
Setup
901
902
Analogue
Analogue
Parental
Channel Decode
-----
-----
Set Select
BACK
Back
1 A
2 D
3 G
4 J
5 M N
6 P Q
7 S T
8 V W
9 Y
0 +
Z
-
H
K
B
E
U
X
O
R
9
.
I
L
C
F
7
8
5
6
3
4
1
2
0
6) Press
[MENU]
to exit.
If you want to cancel
5) Press [
K
/
L
] to select the channel set to decoder off.
• “ ”will disappear.
6) Press [MENU] to exit.
EN
22
Fine Tune
ATV
1) Press [MENU] to display the menu.
2) Press
[
K
/
L
]
to select “TV”, then press
[OK]
.
3) Press [
K
/
L
] to select “Channel”, then press [OK] .
4) Press [
K
/
L
] to select “Fine Tune”, then press [OK] .
• “Channel List” will appear.
Picture
Sound
TV
Setup
Parental
Fine Tune
901
902
-----
-----
Adjust
511.25
MHz
487.25
MHz
Select
BACK
Back
5) Press
[
K
/
L
]
to select a channel you want, then press
[OK]
.
Channel Number:
Name: -----
902
Frequency: 487.25
MHz
Set
BACK
Cancel
6) Press
[ s
/
B
]
to select a frequency you want, then press
[OK]
.
7) Press [MENU] to exit.
Menu Language Selection
DTV ATV
You can select the menu language.
1) Press
[MENU]
to display the menu.
2) Press [
K
/
L
] to select “Setup”, then press [OK] .
3) Press
[
K
/
L
]
to select “Menu Language”.
4) Press [ s
/
B
] to select the language you want.
English Picture
Sound
TV
Setup
Parental
Setup
Menu Language
Time Setup
Subtitle
Teletext
Common Interface
Reset
5) Press [MENU] to exit.
Select
BACK
Back
Time Zone
DTV ATV
You can set the time zone according to the resident area.
1) Press [MENU] to display the menu.
2) Press
[
K
/
L
]
to select “Setup”, then press
[OK]
.
3) Press [
K
/
L
] to select “Time Setup”, then press [OK] .
4) Press
[
K
/
L
]
to select “Time Zone”.
5) Press [ s
/
B
] to select the time difference you want.
Picture
Sound
TV
Setup
Parental
Time Setup
Time Zone
Auto Shut Off
Auto
Off
Select
BACK
Back
Auto : Automatically selects the time zone of your area to ensure the proper performance of the clock.
6) Press
[MENU]
to exit.
Auto Shut Off
DTV ATV
You can set the unit to be shut down automatically if no activity is detected after the power is turned on for 3 hours.
1) Press
[MENU]
to display the menu.
2) Press [
K
/
L
] to select “Setup”, then press [OK] .
3) Press
[
K
/
L
]
to select “Time Setup”, then press
[OK]
.
4) Press
[
K
/
L
]
to select “Auto Shut Off ”.
5) Press [ s
/
B
] to select (“On, Off ”), then press [OK] .
Picture
Sound
TV
Setup
Parental
Time Setup
Time Zone
Auto Shut Off
Auto
Off
Select
BACK
Back
6) Press [MENU] to exit.
23
EN
Subtitle Settings Teletext
ATV
1) Press [MENU] to display the menu.
2) Press
[
K
/
L
]
to select “Setup”, then press
[OK]
.
3) Press [
K
/
L
] to select “Subtitle”, then press [OK] .
• “Subtitle” menu will appear.
Picture
Sound
TV
Setup
Parental
Subtitle
Subtitle(Analogue)
Digital Subtitle Language
Digital Subtitle Language 2nd
Subtitle Type
Off
English
English
-
Select
BACK
Back
“Subtitle(Analogue)”
ATV
4) Press
[
K
/
L
]
to select “Subtitle(Analogue)”.
5) Press [ s
/
B
] to select the setting (“Muting, On, Off ”) you want.
“Digital Subtitle Language , Digital Subtitle Language
2nd”
DTV
4) Press
[
K
/
L
]
to select the item you want.
5) Press [ s
/
B
] to select the language you want.
Note:
“Subtitle Type”
4)
6)
DTV
DTV
Press
While watching a programme, you can change the subtitle language easily using [ (subtitle)] when it is available.
5) Press [ s
/
B
] to select the setting (“-, Hearing Impaired”) you want.
Press
[
K
/
L
] to select “Subtitle Type”.
[MENU] to exit.
DTV ATV
You can change the teletext settings.
1) Press [MENU] to display the menu.
2) Press
[
K
/
L
]
to select “Setup”, then press
[OK]
.
3) Press [
K
/
L
] to select “Teletext”, then press [OK] .
• “Teletext” menu will appear.
Picture
Sound
TV
Setup
Parental
Teletext
Teletext Language
Decoding Page Language
TTX Presentation Level
English
WEST EUR
Level 2.5
Select
BACK
Back
“Teletext Language”
4) Press [
K
/
L
] to select “Teletext Language”.
5) Press
[ s
/
B
]
to select the language you want.
“Decoding Page Language”
You can adjust the decoding paging language.
4) Press
[
K
/
L
]
to select “Decoding Page Language”.
5) Press [ s
/
B
] to select the language you want.
“TTX Presentation Level”
You can adjust the teletext presentation level.
Level 2.5 offers more colours and better graphics than Level 1.5.
4) Press [
K
/
L
] to select “TTX Presentation Level”.
5) Press
[ s
/
B
]
to select the setting (“Level 2.5, Level 1.5”) you want.
6) Press
[MENU]
to exit.
To show the teletext
1) Press [ (text)] to turn on the teletext decoder.
• “Teletext” information will appear.
2) Press [ (text)] repeatedly to show the teletext in transparent mode or picture and teletext mode.
Note: • If you want to select other pages, press
[the Number buttons] or [
K
/
L
] .
• To enlarge fonts, press [ (expand)] .
• To select the teletext subpages, press [ (subpage)] , then press
[the Number buttons] subpage number.
to enter the
• To directly select the page numbers shown at the bottom of the TV screen, use [RED/GREEN/
YELLOW/BLUE] .
• To call up the hidden information, press
[ (reveal)] .
• To hold the current page, press
[
• To hide the teletext, press [SLEEP] .
(hold)]
.
• To go back to the start page, press [ (index)] .
3) Press [ (text)] to turn off the teletext decoder.
EN
24
C.I. (Common Interface) Parental Setting
DTV
This unit is equipped with a C.I. slot. You can enjoy additional services with this function, for example Pay TV. The access restrictions menu will appear on the TV screen when a CI module is installed.
1) Turn off the unit and unplug from an AC outlet.
2) Insert the CI module straight to the C.I. slot of this unit.
• Some CI modules may be a two-piece design consisting of a card reader with the viewing card. When using this kind of card, insert the card reader firmly into the C.I. slot on the unit first.
Then, insert the viewing card into the reader.
DTV ATV
You can set the maturity rating, lock the channel, or set the password.
1) Press
[MENU]
to display the menu.
2) Press [
K
/
L
] to select “Parental”, then press [OK] .
3) Press
[the Number buttons]
to enter the 4-digit number.
Picture
Sound
TV
Setup
Parental
Parental
PIN Code
BACK
Back
3) Plug this unit into an AC outlet and press
[ Q (standby-on)]
to turn on the unit.
4) Press [MENU] to display the menu.
5) Press
[
K
/
L
]
to select “Setup”, then press
[OK]
.
6) Press [
K
/
L
] to select “Common Interface”, then press
7)
[OK] .
Follow the instructions on the TV screen.
Note: • In case of failure, you need to call your CI service provider.
• Menu operations may vary depending on the viewing card. Refer to the manual accompanying the viewing card.
Reset Default
You can restore all the settings to the default except the memorised channels and parental settings.
1) Press
[MENU]
to display the menu.
2) Press [
K
/
L
] to select “Setup”, then press [OK] .
3) Press [
K
/
L
] to select “Reset”, then press [OK] .
• Confirm message box will appear.
4) Press [ s
/
B
] to select [OK] .
• All the settings are restored to the default except the memorised channels and parental settings.
5) Press [MENU] to exit.
• If you have not set up your password, enter 0000.
• After entering the password, “Parental” menu will appear.
Note: If you select “Reset”, all the settings (except the memorised channels) are reset to the default.
“Channel Lock”
You can set particular channels to be invisible.
4) Press [
K
/
L
] to select “Channel Lock”, then press [OK] .
• “Channel List” will appear.
5) Press
[
K
/
L
]
to select the channel you want to lock, then press
[OK]
.
• “ ”will appear on the right of the channel.
Picture
Sound
TV
Setup
Parental
Channel Lock
18
19
20
21
22
38
901
902
Digital
Digital
Digital
Digital
Digital
Digital
Analogue
Analogue
Set
ETV
Euro CH
Drama Now!
WNS
BCT
Eurasia Station
-----
-----
Select
BACK
Back
6) Press
[MENU]
to exit.
• When you select the locked channel, you need to enter the password to watch.
If you want to unlock
4) Press [
K
/
L
] to select “Channel Lock”, then press [OK] .
• “Channel List” will appear.
5) Press [
K
/
L
] to select the channel you want to unlock, then press [OK] .
• “ ”will disappear.
6) Press
[MENU]
to exit.
25
EN
Software Download
“Maturity Rating”
You can set the parental rating to avoid watching an inappropriate programme for your children.
4) Press [
K
/
L
] to select “Maturity Rating”, then press [OK] .
5) Press [
K
/
L
] to select “Parental Rating”.
6) Press [ s
/
B
] to select the age restriction.
Picture
Sound
TV
Setup
Parental
Maturity Rating
Parental Rating No Block
Select
BACK
Back
DTV
You can update the current software when this unit detects a new version of software.
1) When this unit receives software updates automatically, the following message will appear.
Software Download
Software Version : 00000000
A New Version of software is detected.Do you want to upgrade it ?
7) Press [MENU] to exit.
“Enter PIN Code”
You can set your own password.
4) Press [
K
/
L
] to select “Enter PIN Code”, then press
Picture
Sound
TV
Setup
Parental
Enter PIN Code
Enter new PIN code
Confirmation
BACK
Back
[OK]
5) Press [the Number buttons] to enter the new 4-digit number.
6) Press [the Number buttons] to enter the same 4-digit number again.
.
Accept
Remind me Later
Select Next
2) Press [
K
/
L
] to select “Accept”, then press [
B
] .
• Updating will start automatically.
Note: This process may take up to 60 minutes.
3) After the “Software Download” is completed, press
[
B
]
to restart this unit.
Software Download
Software Version : 00000000
Software upgrades successfully! Restart the TV now?
Accept
Next
7) Press
[MENU]
to exit.
EN
26
MAINTENANCE
Panel Cleaning
• If the LCD panel should require cleaning, wipe it with a cotton or soft cloth. Before cleaning the panel, disconnect the power cord.
Cabinet Cleaning
• Wipe the front panel and other exterior surfaces of the unit with a soft cloth immersed in lukewarm water and wrung dry.
• Never use a solvent or alcohol. Do not spray insecticide liquid near the unit. Such chemicals may cause damage and discoloration to the exposed surfaces.
Servicing
• Should your unit become inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts inside.
Turn the unit off, unplug the power cord, and take the unit to a
Service Centre for servicing.
TROUBLESHOOTING GUIDE
Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked possibilities.
Before arranging for service, check these items. It could save you time and money.
QUICK SERVICE CHECK LIST
POSSIBLE REMEDY
Try a new channel, if OK, then possibly due to poor channel reception.
Is unit plugged in?
Power at outlet?
Is unit’s [ Q (standby-on)] on?
Is antenna connected to terminal on the back of the unit?
If outside antenna is being used, check for broken wire.
Check for local interference.
Turn off with [ Q (standby-on)] and then turn it on after about a minute.
Adjust “Colour” control.
Adjust “Contrast” & “Brightness” control.
Check batteries in remote control.
Surrounding temperature is too low.
Life of the Back Light is approximately 50,000 hours. Ask the Service Centre to replace.
It is quality of the LCD Panel.
Enter the default password “4737”.
×
× × × × × × × × × × × ×
×
× × × × ×
× × × × × × × × × ×
× × × × × × ×
×
×
×
×
×
× ×
×
× ×
×
×
×
×
×
27
EN
SPECIFICATIONS
General Specifications
Television system: PAL B/G TV standard
PAL D/K TV standard
SECAM L TV standard
SECAM L' TV standard
SECAM B/G TV standard
SECAM D/K TV standard
Terminals
S-Video input:
Video input:
Audio input:
PC input:
AUDIO/VIDEO:
Component Video input:
HDMI input:
Coaxial digital audio output:
Headphone:
Stereo Sound System
2 speakers
Sound output:
Mini DIN 4-pin jack x 1
RCA jack x 1
RCA jack x 4
D-Sub 15pin x 1 (RGB)
Mini jack Ø 3.5 mm x 1 (AUDIO)
21 pin scart jack x 2
RCA jack x 3
HDMI 19pin x 3
RCA jack x 1
1/8 inches x 1 (3.5 mm)
5 W, 16 ohm x 2
Other Specifications
Remote control:
Power requirements:
Power consumption:
LCD:
Dimensions (H x W x D)
(without stand):
(with stand):
Weight
(without stand):
(with stand):
Digital encoded infrared light system
AC 220-240 V
~
, 50 Hz
130W (Standby: less than 1W)
31.5 inches
519.3 mm x 760.0 mm x 113.5 mm
563.0 mm x 760.0 mm x 234.0 mm
9.1 kg
9.6 kg
• Designs and specifications are subject to change without notice and without our legal obligation.
EN
28
DECLARATION OF CONFORMITY
This product complies with the requirement of the directives
EMC-Directive:
Low Voltage Directive:
ErP Directive:
2004 / 108 / EC
2006 / 95 / EC
2009 / 125 / EC
We: Funai Electric (Polska) Sp. z o.o.
ul. Inżynierska 1
Nowa Sól, 67-100 / Poland declare that the following product:
LCD Television
Model LH7-M32BB
Trade Name: Funai is in compliance with following regulations.
EN55013: 2001+A1: 2003+A2: 2006
EN55020: 2007
EN61000-3-2: 2006 Class D
EN61000-3-3: 1995+A1: 2001+A2: 2005
EN60065: 2002+A1: 2006+A11: 2008
EN55022: 2006 Class B
EN55024: 1998+A1: 2001+A2: 2003
29
Printed in EU
EN
Web Site: http://www.funai.eu
1EMN24879A
A93F0FP/A93F2EP
advertisement