NUTV4

4 Channel Marine 4” UTV/ATV/BOAT

Audio System with Bluetooth

OWNER’S MANUAL

Thank you for making your choice for marine audio entertainment!

Its compact, Marine design provides flexible mounting possibilities, and makes it simple to expand the audio system capabilities of your vehicle.

NUTV4

4 Channel Marine UTV/ATV/BOAT Audio System with Bluetooth

One Pair 4'' 2-Way Marine Speaker:

• 4'' High Quality Poly Injection Cone

• Butyl Rubber Surround

• Shinny Black Plastic Enclosure

• Fits 1.25”-2” Bars

• 1” High Temperature KEISV Voice Coil

• 1'' PEI Neodymium Dome Tweeter

• 100 Watts RMS / 200 Watts Peak

• Frequency Response: 100-20KHz

• Impedance: 4 Ohms

4 Channel Marine Power Amplifier

• 4 x 100 Watts at 4 Ohms

• Anti-Thump Turn-On

• Soft Turn On/Off

• Bluetooth Streaming

• AUX Input

• Volume Gain Remote Control

• T.H.D: <0.05%

• S/N Ratio: >95dB

• Channel Separation: >65dB

• Frequency Response: 10Hz- 30kHz

• Fuse : 1 x 20A

• Bluetooth 3.0 Technology

• Bluetooth Auto Connected While Power on

• Bluetooth Auto Disconnected While Aux-in (3.5mm Connector)

• Easy and Quick Installed Handle-bar Mount Bracket is Included

• Bluetooth Console Dimension: 2.12''(W) x 1.16''(H) x 3.83''(L)

• Amplifier Dimensions: 6.3''L x 3.67''W x 2.11''H

1

What is included?

When first unpacking your new amplified Marine speaker system,

Please check first that the package contains all of the items below. If something is missing, contact the store where you purchased the product.

NUTV4

 One Pair 4” 2 Way Marine Speaker

 One Piece

 One Piece

4 C h a n n e l M a ir n e P o w e r

Bluetooth controller

A m p il if e r

Installation precautions

Before you drill or cut any holes, investigate your vehicle’s layout very carefully.

Take special care when you work near the gas tank, fuel lines, hydraulic lines and electrical wiring.

Never operate the amplifier when it is unmounted. Attach all audio system components securely within the amplifier to prevent damage, especially in an accident.

Do not mount this amplifier so that wire connections are unprotected. in a pinched condition, in contact with any metal surfaces in your vehicle, or likely to be damaged by nearby objects.

Before making or breaking power connections in your system, disconnect the vehicle batte r y. Confirm that your head unit or other equipment is turned off while connecting the input jacks and speaker terminals.

If you need to r eplace the power fuse, replace it only with a fuse identical to that supplied with the amplifier, Using a fuse of a different type or rating may result in damage to your audio system or your amplifier which is not covered by the manufactuer’s warranty.

2

INSTALLATION INSTRUCTIONS:

STEP1 STEP3

Remove Both

Screws

Screws

Mounting

Bracket

Rubber pad

Mounting

Bar

YOU'LL NEED: A SCREW DRIVER

Remove the two screws from the bracket to separate the Speaker case and the bracket.

STEP2

Remove backing

From Rubber Pad

& Push Down

YOU'LL NEED: 2 SCREWS, MOUNTING

BRACKET, RUBBER PAD AND THE

MOUNTING BAR

Mount the speaker on the bar where you want. The mounting dimension is available from 1.25"~ 2”.

STEP4

YOU'LL NEED: THE RUBBER PAD TO

ADJUST THE SIZE OF THE MOUNTING

BRACKET

Remove the backing from the Rubber

Pad and stick on the mounting surface

FINISHED INSTALLATION !!

BEGIN ENJOYING YOUR MUSIC !!

NOTE

Rubber Pad in 3 Specification: Rubber Pad Quantity You Need for Each Mounting Dimension:

Pad No.1: 76X30X2mm* 6PCS

Pad No.2: 140x30x3mm*4PCS

Pad No.3: 38x30x3mm*4PCS

2” Bar: Pad No.1* 2PCS

1.75” Bar: Pad No.1*2PCS and Pad No. 2*1PC

1.5” Bar: Pad No.1*2PCS and Pad No. 2*2PCS

1.25” Bar: Pad No.1*2PCS and Pad No. 2*3 PCS

Attention: Please Cut Pad No.2 into the Size You Need for Each Mounting Bar Size

Note: pad No.3 is an extra small pad that can be used in case you need an extra spacer for a better grip

3

Power and Speaker Wiring

+

WHITE

-

WHITE/BLACK

+

GRAY

-

GRAY/BLACK

+

GREEN

-

GREEN/BLACK

+

PURPLE

-

PURPLE/BLACK

4-8 ohm speakers

Insert

NUTV4

4 Channel UTV/ATV/BOAT Audio System

Connect to the

Remote Control

LED

BLACK

-

RED

+

BATTERY wire color

Red

Black

White

White/Black

Gray

Gray/Black

Green

Green/Black

Purple

Purple/Black

Description

Battery (+), 12dc / 12vdc = ON

Battery (-), Ground

CH1 (+)

CH1 ( - )

CH2 (+)

CH2 (-)

CH3 (+)

CH3 ( - )

CH4 (+)

CH4 (-)

4

On/Off &

Background Light Next Song Volume Up

AUX Input

Connect to the Amplifier

Play / Pause Previous

Song

Volume Down

Bluetooth Pairing and Connection:

1.

2.

3.

Connect Bluetooth controller box to your device

Press and Hold for three seconds until power indicator lights (red)

The system will automatically go into pairing mode

The power indicator will turn red for about 4-6 seconds and then alternating red and blue (Bluetooth blue Power red)

Please be sure that Bluetooth is turned ON. Select NOAM Audio on your device to connect Bluetooth controller (if the Bluetooth controller is connected the light will turn blue and not flash)

4.

When the device is out of Bluetooth range, Bluetooth will be disconnected automatically and automatically reconnect when detected in range again. (If not please just repeat steps 2 and 3)

5.

When Bluetooth is disconnected or the 3.5mm AUX Input is plugged in, the power indicator will glow red.

Playing Music:

1.

Press and hold for three seconds to turn On/OFF

2.

Press shortly in order to control the red background light

3.

Press to start or pause the music

4.

Press shortly for next track

5.

Press shortly for Previous track

6.

Press shortly for volume up

7. Press shortly for volume down

5

Bluetooth Installation

(MODE 1“Surface mount”)

STEP1

1. Install “Z” shaped bracket threaded on to the Bluetooth controller hook.

(packed with Bluetooth controller.)

Use the hole on the other bracket’s end to mount the controller. any screw/bolt and a washer will allow a clean and easy surface mounting.

STEP2

2. Slide the Bluetooth controller into the hook

STEP3

3. Press down the Bluetooth controller hook and then slide out the Bluetooth controller box at the same time to remove the Bluetooth controller

Bluetooth Installation

(MODE 2“Push-Fixed in Mount”)

STEP1 Decide the place for Bluetooth remote installation. Draw and cut the size into

85 x 49mm ( L x W)

STEP2

Push in the Bluetooth remote

66