UNO2DUO™

• featuring

• Owner’s Manual

©2018 Graco NWL0000742780B

1 WARNING

2 Features

2-A UNO2DUO™ Use Positions

2-B Parts List

3 Assembly

3-A To Open Stroller

3-B Rear Wheels

3-C Front Wheels

3-D Cup holder and Phone holder

3-E Assemble Seat(s)

4 Use

4-A To Use Toddler Seat

4-B To Use Toddler Seat in Bassinet Position •

4-C To Extend Platform for Child Use, Extra storage or Rear Seat

Attachment

4-D To Secure Child

4-E To Recline

4-F Brakes

4-G Swivel Wheels

4-H To Attach Graco® Infant Car Seat to Stroller Frame in Front

Position

4-I To Attach Graco® Infant Car Seat to Toddler Seat in Front

Position

4-J To Fold Stroller Frame

4-K Harness Covers

4-L Crotch Strap Cover

4-M To Adjust Handle

Failure to follow these warnings and the assembly instructions could result in serious injury or death.

Only use product as instructed.

PLEASE SAVE OWNER’S

MANUAL FOR FUTURE USE.

ADULT ASSEMBLY REQUIRED.

NEVER LEAVE child unattended. Always keep child in view while in stroller.

AVOID SERIOUS INJURY from falling or sliding out. Always use seat belt. After fastening buckles, adjust belts to get a snug fit around your child.

USE OF THE FRONT SEAT, REAR

SEAT, OR STANDING PLATFORM with a child weighing more than

50 lb (22.7 kg) or taller than

45 in. (114.3 cm) will cause excessive wear and stress on the stroller.

TIPPING HAZARD! DO NOT

OVERLOAD FRONT SEAT, REAR

SEAT, OR STANDING PLATFORM

PAST THE MANUFACTURERS

RECOMMENDED WEIGHT

RATING.

AVOID FINGER ENTRAPMENT:

Use care when folding and unfolding the stroller. Be certain the stroller is fully erected and latched before allowing your child near the stroller.

AVOID STRANGULATION:

DO NOT place items with a string around your child’s neck, suspend strings from this product, or attach strings to toys.

NEVER USE STROLLER ON

STAIRS or escalators. You may suddenly lose control of the stroller or your child may fall out.

Also, use extra care when going up or down a step or curb.

STROLLER TO BE USED only at walking speed. Product not intended for use while jogging, skating, etc.

TO PREVENT TIPPING, place more than 1 lb (.4 kg) on the parent’s cupholder or phone holder.

TO AVOID BURNS,

DO NOT use storage basket as a child carrier.

NEVER ALLOW YOUR

STROLLER to be used as a toy.

DISCONTINUE USING YOUR

STROLLER should it become damaged or broken.

do not

never put hot liquids in the parent’s cupholder.

TO PREVENT A HAZARDOUS,

UNSTABLE CONDITION handle or canopy.

, never place purses, shopping bags, parcels or accessory items on the

TO PREVENT A HAZARDOUS,

UNSTABLE CONDITION , do not place more than 10 lb

(4.5 kg) in the storage basket.

ONLY USE THE TODDLER

SEATS PROVIDED WITH THIS

STROLLER OR PURCHASED

SEPARATELY AND SPECIFIED

FOR USE WITH THIS

STROLLER.

USING GRACO® INFANT CAR

SEAT WITH STROLLER:

• TO AVOID INJURY TO YOUR

CHILD: THIS STROLLER IS

ONLY COMPATIBLE WITH

GRACO® SNUGRIDE®

INFANT CAR SEATS WITH

CLICK CONNECT™. Only use with Graco® infant car seats that have the Click

Connect™ logo. Improper use of this stroller with other manufacturers’ car seats may result in serious injury or death.

• READ THE MANUAL provided with your Graco car seat before using it with your stroller.

• ALWAYS SECURE your child with the car seat harness when using the car seat in the stroller.

If your child is already in the car seat, check that the child is secured with the harness.

• NEVER ATTACH infant car seat in the toddler seat without the child’s tray and side armrests attached.

10

• ONLY USE toddler seat on the stroller and do not remove, reverse, or carry the toddler seat while child is in it.

• ONLY USE bassinet on the stroller and do not remove, reverse, or carry the bassinet while child is in it.

• ALWAYS release the webbing strap buckle to lower the foot end of the toddler seat before placing child in the bassinet.

• TIPPING HAZARD: Stroller could tip backwards. Do not allow child to step on or off the rear platform without caregiver assistance.

• FALL HAZARD: Never allow child to stand on the rear platform when going up or down curbs or steps.

• ALWAYS LOCK BRAKES before folding.

2-

A UNO2DUO™ Use Positions

WARNING

DO NOT allow child to stand on platform facing backwards. To avoid falling, child must hold onto frame.

One Child

Infant car seat on certain models or sold separately)

Extra Storage - Frame can be extended in any of the 8 use positions above.

Two Children

Second Seat (on certain models or sold separately)

2-B Parts List

This model may not include some features shown below. Check that you have all the parts for this model .

Tools required:

Phillips Screwdriver

All models

2X

2X

2X

On certain models

2X

2X

2X

3-A

To Open Stroller

WARNING

• Remove and IMMEDIATELY discard the zip ties.

Zip ties

Be sure to place stroller on top of a piece of cardboard or some other protective cover to prevent any damage to floor.

1. Open stroller lock.

2. Lift handle of stroller up.

3. CHECK that the stroller is completely latched open every time you open the stroller and before continuing with the rest of the assembly steps.

SNAP!

3-B Rear Wheels

Fenders

Extension

Extension

1. Attach fender with extension facing the rear of stroller. Insert tabs into stroller frame and slide to secure.

2. Secure with screw.

Repeat on other fender.

Rear Axle

1. Remove protective end cap from each axle end.

2. Insert axle through axle opening.

Rear Wheels

2X

3. Place wheel on axle.

4. Place washer on axle.

5. Push straight side of pin through axle hole. Pin will separate around the axle. Curved end of pin MUST face up as shown.

Repeat steps 3-5 on other side.

6. Snap hubcap over pin as shown.

Repeat with other hubcap.

2X

SNAP!

3-C

Front Wheels

2X

SNAP!

1. Attach front wheels to front leg tubes as shown.

2. CHECK that wheels are securely attached by pulling on wheel assembly.

3-D Cup holder and Phone holder

1. Line up opening in cup holder or phone holder with mount on stroller and press onto stroller tube.

2. Make sure cup holder or phone holder is snapped securely into mount.

3-E Assemble Seat(s)

1. Seat wire should be inserted as shown. DO NOT insert with wire facing head end of seat.

SNAP!

2. Insert seat wire into openings marked with an arrow on sides of toddler seat.

CHECK that seat wire is securely attached to toddler seat by pulling on it.

Arrow

3. Secure flap around wire with 3 snaps. Repeat on other toddler seat (on certain models).

Canopy

Toddler Seat - 3 panels with visor

Second Seat (on certain models) - 2 panels with visor

1. Slide canopy pivots onto mounts on each side of the toddler seat as shown.

SNAP!

2. Fasten hook and loop tape on the rear of canopy as shown. MAKE

SURE canopy is always fastened with the hook and loop tape when toddler seat is in use.

(on certain models)

Repeat steps on second seat.

Child’s Tray

WARNING

Always secure your child with the seat belt. The tray is not a restraint device. DO NOT lift the stroller by the child’s tray. Use care when snapping the tray on the stroller with a child in the stroller.

1. Insert side armrests into slots on each side of seat until they click into place.

Pull on armrests to make sure they are attached.

2. Attach child’s tray to side armrests.

3. To open, press button on bottom and rotate child’s tray up.

4. To remove child’s tray, (a) press buttons on bottom on both ends and (b) lift off.

a b

5.

(a) Press release buttons on underside of side armrests and

(b) pull away from stroller.

a b

4-A To Use Toddler Seat

WARNING

• ONLY USE toddler seat on the stroller and do not remove, reverse, or carry the toddler seat while child is in it.

See warnings for additional information.

To Attach Toddler Seat

1. NOTE: Seat can be placed forward or rear facing on the front mounts.

Seat can be placed forward facing ONLY on rear mounts.

2. To attach seat, place seat on mounts as shown until they lock into place on both sides of the stroller.

3. MAKE SURE seat mounts are securely attached to the stroller on both sides as shown.

4. CHECK that toddler seat is securely attached to the stroller by pulling up on toddler seat.

SNAP!

¡CRAC!

To Remove Toddler Seat

1. Squeeze buttons on both sides of the seat and pull up as shown.

Canopy

1. Pull forward to open canopy.

2. Push backwards to close canopy.

3. Pull flap forward to open and backwards to close canopy window.

4. To open or close canopy visor.

4-

B To Use Toddler Seat in Bassinet Position

WARNING

• Child may slip into leg openings and strangle.

• NEVER use in full recline position unless footrest is in the bassinet position.

• Never use any head support in the reclined bassinet position.

• ONLY USE bassinet on the stroller and do not remove, reverse, or carry the bassinet while child is in it.

• ALWAYS remove the child’s tray and side armrests when using in bassinet position.

• ALWAYS release the webbing strap buckle to lower the foot end of the toddler seat before placing child in the bassinet.

See warnings for additional information.

1. Remove side armrests and child’s tray. Press buttons on bottom on both sides and pull off of the stroller.

ALWAYS remove the child’s tray and side armrests when using in bassinet position.

2. Remove front toddler seat if it is attached. Squeeze buttons on both sides of the seat and pull up as shown.

3. Flip toddler seat over and disconnect buckle on foot end.

ALWAYS release the webbing strap buckle to lower the foot end of the toddler seat before placing child in the bassinet.

4. To attach seat, place seat on mounts as shown until they lock into place on both sides of the stroller.

Bassinet can only be used in front seat position.

Bassinet can be attached forward or rear facing.

MAKE SURE buckles do not interfere with seat and mounts.

5. MAKE SURE seat mounts are securely attached to the stroller on both sides as shown.

SNAP!

6. To recline seat back, push button down and pull seat towards the rear.

7. To put in bassinet position, pull handle on top of seat and rotate seat flat.

DO NOT adjust with child in seat.

SNAP!

8. CHECK seat is secured in bassinet position as shown.

4-C To Extend Platform for Child Use, Extra storage or Rear Seat Attachment

WARNING

• DO NOT use bassinet, or car seat in rear position.

• DO NOT allow child to stand on platform facing backwards.

See warnings for additional information.

Rear Position Mounts

a

1.

To extend frame and to access rear toddler seat mounts: a.

pull extension handle under rear of platform, b.

pull platform rearward.

a b

2. CHECK that frame locks fully open and mounts are visible.

WHEN ADJUSTING THE LOWER

FRAME, be sure it locks into the fully extended or fully retracted position and only use in one of these two locked positions.

SNAP!

3.

To attach toddler seat in rear position, place attachment mounts in upright position by: a.

rotating up, b.

snapping into place.

a a

SNAP! b b

Reverse steps to shorten frame.

To Attach Second Seat

For models that do not come with a second seat one may be purchased separately.

1. To attach second seat, be sure attachment mounts are in the vertical position as shown. Place seat on mounts as shown until they lock into place on both sides of the stroller. Seat can only be placed forward facing.

See warnings for additional information.

2. MAKE SURE seat mounts are securely attached to the stroller on both sides as shown.

3. CHECK that toddler seat is securely attached to the stroller by pulling up on toddler seat.

SNAP!

To Remove Second Seat

1. Squeeze buttons on both sides of the seat and pull up as shown.

Canopy

1. Pull forward to open canopy.

2. Push backwards to close canopy.

3. Pull flap forward to open and backwards to close canopy window.

4. To open or close canopy visor.

Second seat visor should be retracted when front seat is reclined.

4-D To Secure Child

WARNING

Falling Hazard: Always use the seat belt.

5 Point Harness

1. To open, press button on buckle to release the waist straps.

2. To close, slide shoulder strap connectors onto waist straps and insert into buckle.

3. Use slide adjuster at shoulder and waist for tighter adjustment. To change shoulder harness slots, see page 46.

1. To open, press button on buckle to release the waist straps.

2. Slide shoulder strap connectors off of waist straps.

Use slide adjuster at shoulder and waist for further adjustment.

Repeat on other side.

Utilisez le régulateur coulissant

à l'épaule et à la taille pour un ajustement plus précis. Répétez de l'autre côté.

Use el ajuste deslizable en el hombro y la cintura para hacer ajustes adicionales. Repita el proceso del otro lado.

3. Remove shoulder straps from stroller.

4. Attach waist straps to harness buckle as shown.

5. Use slide adjuster at waist for tighter adjustment.

6. To open, press button on buckle to release the waist straps.

Adjusting Shoulder Harness position

Shoulder harness anchor—larger child

Shoulder harness anchor—smaller child

Slide adjuster

1. Push harness anchor through the front of the seat then re-insert through desired slots at the same height level. Use either shoulder harness anchor in the slots that are closest to child’s shoulder height. Use slide adjuster for further adjustment.

4-E To Recline

WARNING

When making adjustments to the stroller seat, make sure child’s head, arms, and legs are clear of moving seat parts and stroller frame.

1. To recline push button down and pull seat towards the rear.

2. To raise, pull both straps up.

4-F

Brakes

WARNING

CHECK that brakes are on by trying to push stroller.

ALWAYS LOCK BRAKES before folding.

SNAP!

1. Push down on either brake to lock brakes.

SNAP!

2. Push up on either brake to unlock brakes.

4-G

Swivel Wheels

Front swivel wheels lock for use on uneven surfaces such as grass, stones or gravel.

1. To lock, press up.

SNAP!

2. To unlock, press down.

SNAP!

4-H To Attach Graco

®

Infant Car Seat to Stroller

Frame in Front Position

For models that do not come with an infant car seat one may be purchased separately.

WARNING

Use only a Graco® SnugRide® Click Connect™ car seat with this

stroller. This stroller is only compatible with Graco® SnugRide® infant car seats with Click Connect™. Only use with Graco® infant car seats that have the Click Connect™ logo. Improper use of this product with a car seat may result in serious injury or death. Read the manual provided with your Graco car seat before using it with your product.

• Always secure your child with infant car seat harness when using the car seat in the product. If your child is already in the car seat, check that the child is secured with the harness.

• Child in rear seat can chew on the infant car seat webbing when the infant car seat is attached directly to the stroller frame in front position. Always secure the infant car seat rear adjust harness ends through the storage hooks or tuck the front adjust webbing under the seat pad as applicable.

10

1. Infant car seat can be attached to stroller frame rear and forward facing. DO NOT use car seat in rear seat position.

2. Insert car seat into stroller and push down on car seat until the latches snap into the seat attachment mounts.

3. Check that infant car seat is securely attached by pulling up on it.

Mount

Supports

4. To remove car seat: (a) squeeze release handle at back of car seat, and (b) lift car seat out of the stroller.

a b

4-I To Attach Graco

®

Infant Car Seat to Toddler

Seat in Front Position

WARNING

• NEVER ATTACH infant car seat in the toddler seat without the child’s tray and side armrests attached.

1. NOTE: Infant car seat can ONLY be attached rear facing to toddler seat when toddler seat is in forward or rear facing position.

2. Recline seat back to full recline position. (See section 4-E, p. 47).

3. Find mounts in toddler seat.

4. Insert infant car seat into stroller and push down on infant car seat until the latches snap into the

Click Connect™ mounts.

SNAP!

5.

Check that infant car seat is securely attached by pulling up on it.

a b

6.

To remove infant car seat:

(a) squeeze release handle at back of infant car seat, and

(b) lift infant car seat out of the stroller.

4-J

T o Fold Stroller Frame

NOTE: Stroller can be folded with front toddler seat installed forward-facing or with no seats attached.

DO NOT fold stroller with:

• a toddler seat rear-facing,

• a toddler seat in the rear position,

or

• an infant car seat.

ALWAYS LOCK BRAKES before folding.

a a

1.

Before folding stroller: a.

remove infant car seat and rear toddler seat.

b.

lock brakes.

SNAP! b a b

2. Slide handle release button in (a) and rotate handle forward (b).

3. Rotate handle down.

4. CHECK that the storage latch is secured.

4-K

Harness Covers

1. To attach harness covers, slide onto shoulder harness straps.

4-L Crotch Strap

Cover

1. To attach crotch strap cover, slide onto crotch strap.

4-M To Adjust Handle

b

To adjust handle, (a) lift up on handle release and (b) slide handle into desired position. a

Learn more about automotive seats on our website.