Cleveland Mixer Kettles, Gas Fired Horizontal Agitator, Tilting Specification Sheet

Item
Quantity
MIXER KETTLES, GAS-FIRED
HORIZONTAL AGITATOR
2/3 STEAM JACKETED, TILTING
Models
• HA-MKGL-60-T
• HA-MKGL-80-T
FCSI Section 11400
Approved
Date
Standard Features
• HA-MKGL-100-T
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Short Form Specifications
Shall be Cleveland Model HA-MKGL- ____ -T, gas
fired, 2/3 steam jacketed, ____ gallon operating
capacity, tilting horizontal agitator mixer kettle.
190M BTU High Efficiency Power Burner heating
system with automatic Glow Type Ignition, type
304 stainless steel with #4 finish on kettle and
supports, insulated Heat Exchanger, 50 psi jacket
rating, 3HP Motor Drive for mixer arm with
variable speed control, variable temperatures
control, L.E.D. indicators for heat cycle and low
water warning, 3" dia. Butterfly Valve.
•
•
•
•
•
•
•
•
•
•
•
60, 80 or 100 gallon working capacity
Type 304 stainless steel with #4 finish on kettle and supports
Precise solid state temperature control
Solid state low water safety controls in a plug-in module
L.E.D. indicators for heat cycle and low water warning
3˝ dia. butterfly valve
Three (3) horse power horizontal agitator drive
Variable mixer speed control from 5 to 20 r.p.m. with agitator
start/stop controls
Spring loaded teflon blades scrape the entire heated surface area
Internal mixing fins for most efficient, uniform mixing of products
Easily removable agitator without the use of tools
190 M-BTU high efficiency power burner heating system for fast
heat-up and recovery times
"Glow type" automatic safety ignition system
Power tilt mechanism with case hardened self-locking worm and
segment gear
Kettle steam jacket permanently filled with treated distilled water
50 psi steam jacket rating and safety valve
Front mounted combination pressure-vacuum gauge
Heavy duty welded rim bar
Water fill faucet with swing spout for hot and cold water
Faucet mounting bracket.
Spring assisted, hinged stainless steel cover
Standard for Natural Gas operation
Standard Electrical for agitator drive is 208V/3Ph/60Hz
Accepted for use in USDA inspected facilities
Typical approvals include AGA, CSA, CE, NSF and ASME
Options & Accessories
•
•
•
•
•
•
•
•
•
Type 316 stainless steel kettle liner for high acid products (316)
Dolly for horizontal agitator
Stainless steel bi-fold hinged cover
3" diameter air operated flush mounted piston draw-off valve
with variable control (FPVA3, for use with a food pump, replaces
3˝ butterfly valve, requires air compressor)
Automatic water meter (GMF or LMF) Wall or stand mounted)
Food Strainer (FS)
Kettle Accessory Kit (KAK) includes:
• Clean-up Brush (CB)
• 36" Kettle Paddle (KP)
• 36" Kettle Whip (KW)
• 36" Kettle Brush (KB)
• Draw-off Brush (DB)
• 24 oz. Ladle (KL)
Option for propane gas operation (PG)
Voltage option for agitator drive other than standard
208V/3Ph/60Hz
KE004046-48
18301 St. Clair Street
Cleveland, OH 44110
Tel 1.216.481.4900
Fax 1.216.481.3782
Email [email protected]
www.clevelandrange.com
Section 8, Page 21
CLE_5659A 10 / 2018
Mixer Kettles
Project
ELECTRICAL
SUPPLY
GAS SUPPLY
(PIPING 3/4" NPT)
VOLTS: 208/240
TYPE: NAT or LP
PHASE: 3
BTU PER CU. FT.:
AMPS: 15
1000 (NAT), 2500 (LP)
FREQ:
60 HZ
SUPPLY PRESSURE:
APPROVALS
AGA
CGA
NSF
A AIR SUPPLY (PIPING 1/2" NPT)
PRESSURE:
90 - 100 PSI
(only required for optional 3" dia.
piston draw-off valve)
H C HOT & COLD
WATER
60 GAL 1010 LBS.
458 KG.
80 GAL 1120 LBS.
508 KG.
100 GAL 1325 LBS.
601 KG.
CLEARANCE
4" to 14" W.C.
1/2" NPT CONNECTION
BTU RATINGS:
40-60 PSI PRESSURE
190,000 per hour
RIGHT: 3", LEFT: 3"
REAR: 3"
(ALLOW 12" SPACE
MINIMUM ON LEFT
SIDE FOR SERVICE)
G
WALL
APPROX.
SHIPPING
WEIGHTS
5 3/4
33 1/8
39 1/16
U
12
16
MIXER
BRIDGE
J
MIXER BRIDGE
SEE
FOOT DETAIL
M
W
VIE OM
FR FT
LE
MIXER
BRIDGE
KETTLE
KETTLE
FLOOR DRAIN
C
K
L
FLOOR DRAIN &
FEET LOCATION DET.
KETTLE
2PIECE COVER
WITH SCREEN
5 1/2"
5/8"Ø,
2 HOLES
ON
4" B.C.D.
RIM BAR
(1/2 x 1 STAINLESS STEEL)
A (I.D.)
90º
2"
36.042
3/8"
E
(COVER
FULLY OPEN)
1" (MAX. ADJUSTMENT)
SOLID
FOOT DETAIL
H
C
Cleveland
6
5
4
7
3
8
B
2
9
1
Max.
MIN.
LOW
WATER
A
A
S
Mixer Kettles
13
4 INCH MINIMUM
6 INCH RECOMMENDED
(SEE ALSO FLOOR DRAIN &
FEET LOCATION DET.)
RECOMMENDED
FLOOR SLOPE
1 INCH IN 4 FEET
S
8 7/8
G
REF
KETTLE WITH REGULAR FAUCET
& BUTTERFLY VALVE (BV-3)
3 MIN.
CLEARANCE
PIPE DRAIN RECOMMENDED
MINIMUM VALVE SIZE PLUS 1"
DIMENSIONS
MODEL
HA-MKGL-60-T
HA-MKGL-80-T
HA-MKGL-100-T
A
29 1/2"
33"
35 1/2"
B
50 1/4"
51 3/4"
54 1/4"
C
62 5/8"
66 1/8"
68 5/8"
D
52 1/4"
52 3/4"
55 1/4"
E
93 1/2"
96 1/2"
102 1/2"
G
42"
45 11/16"
48 3/16"
J
78 5/8"
84 5/8"
96 1/4"
K
28"
30"
32"
L
10 3/8"
11 7/16"
11 5/8"
M
53"
57"
66"
N
65 3/8"
68 7/8"
71 3/8"
P
69 1/2"
69"
71 1/2"
S
21 1/4"
20 1/2"
22"
U
8"
9"
10"
NOTES:
Cleveland Range equipment is built to comply with applicable standards for manufacturers. Included among those approval agencies are: UL, A.G.A., NSF, ASME/N.BD., CSA, CGA, ETL, and others.
Installations of back flow preventers, vacuum breakers and other specific code requirements are the responsibility of the owner and installer.
All vertical dimensions shown are minimum.Feet are adjustable to +1" maximum.
Manufacturer must be notified if unit will be operating above 2000' altitude.
Consult factory for manufactured gas.
Cleveland Range reserves the right of design improvement or modification, as warranted.
18301 St. Clair Street
Cleveland, OH 44110
Tel 1.216.481.4900
Fax 1.216.481.3782
Email [email protected]
www.clevelandrange.com
Section 8, Page 22
10 / 2018
(NOT TO SCALE)