Epson EV-100 Owner Manual
विज्ञापन
विज्ञापन
User's Guide
Notations Used in This Guide
•
Safety indications
The documentation and the projector use graphical symbols to show how to use the projector safely.
The indications and their meaning are as follows. Make sure you understand them properly before reading the guide.
Warning This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.
Caution This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.
•
General information indications
Attention a s
[Name]
Menu Name
Indicates procedures which may result in damage or injury if sufficient care is not taken.
Indicates additional information and points which may be useful to know regarding a topic.
Indicates a page where detailed information regarding a topic can be found.
Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See the "Glossary" section of the "Appendix".
s
Indicates the name of the buttons on the remote control.
Example: [Esc] button
Indicates Configuration menu items.
Example:
Select Brightness from Image .
Image - Brightness
Safety Warning and Cautions
Make sure you read the following before you use the projector.
s
Safety Instructions
Warning and Cautions on Installation
Use the mount supplied to install the projector on a wall or suspend it from a ceiling.
Optional mounts are necessary to install the projector on lighting tracks or to install it on the floor or a table.
s
"List of Optional Accessories" p.154
Warning
•
Do not use or install the projector where it may be subject to water or rain, or high humidity, such as outdoors, in a bathroom, or shower room, and so on. Otherwise, it could cause a fire or electric shock.
• A special method of installation is required when suspending the projector from a ceiling or mounting it on a wall. If installation work is not carried out correctly, the projector could fall down. This may result in injury or accidents. Make sure you contact a professional.
• If you use adhesives on the mount fixing points to prevent the screws from loosening, or if you use things such as lubricants or oils on the projector, the projector case may crack causing it to fall from its mount. This could cause an accident or injury to anyone under the mount.
Do not use adhesives, lubricants, oils, or similar substances to loosen the screws when adjusting the installation mount.
• If you use adhesives to prevent the screws from loosening, or use lubricants, oils, or similar substances on the ball joint, the strength holding the image projection unit in place decreases which could cause an accident or injury to occur.
• When installing the projector in a high position, take measures to prevent falling by using wires to ensure safety in an emergency, such as an earthquake, and to prevent accidents. If it is not installed correctly, it could fall causing an accident and injury.
•
Do not cover the projector's air intake vent or air exhaust vent. If either of the vents is covered, the internal temperature could rise and cause a fire.
• Do not place flammable objects in front of the lens. If you set the schedule to turn on the projector automatically, any flammable objects placed in front of the lens could cause a fire.
3
Safety Warning and Cautions
Warning
•
When adjusting the orientation of the image projection unit, make sure that the projected light does not fall on the projector's power supply section. If projected light falls on the projector, it may become hot causing an injury or fire to occur.
• Do not tie the power cord and other connection cables together. Otherwise, it could cause a fire.
• Only use the specified power-supply voltage. Otherwise, it could cause a fire or electric shock.
•
Be careful when handling the power cord. Otherwise, it could cause a fire or electric shock. Note the following when handling the power cord.
- Do not plug multiple power cords in a single electric outlet.
- Do not plug in the power cord if there are any foreign substances, such as dust, stuck to it.
- Make sure you insert the power cord all the way in.
- Do not plug in or unplug the power cord with wet hands.
- Do not pull the cord when unplugging the power cord. Make sure you hold it by the plug.
• Do not use a damaged power cord. Otherwise, it could cause a fire or electric shock. Note the following when handling the power cord.
- Do not alter the power cord.
- Do not place any heavy objects on the power cord.
- Do not bend, twist, or pull the power cord forcibly.
- Do not layout the power cord near a heating device.
Caution
Do not place the projector on an unstable surface, such as on an unstable table or tilted surface. Otherwise it may cause an injury.
Make sure you install the optional Floor Stand when placing the projector on the floor and so on.
Attention
•
Do not install the projector in a location that is subject to vibration or shock.
•
Do not install the projector near a high-voltage line or object that generates magnetism. Otherwise, the projector may not work correctly.
•
Do not use or store the projector in a location that is subject to extreme temperatures. Also, avoid sudden temperature changes.
Make sure you use or store the projector in a place that is within the following operating or storage temperature ranges.
- Operating temperature range
+5 to +40˚C (No condensation)
- Storage temperature
-10 to +60˚C (No condensation)
•
When using at an altitude that exceeds 1,500 m, set High Altitude Mode to
On .
s Extended - Operation - High Altitude Mode
•
Make sure you secure the following space around the projector so as not to block the Air intake vent and the Air exhaust vent.
Do not install the projector in a location that does not allow air to circulate, such as on a shelf or in a box.
•
When installing the projector on a ceiling or wall, make sure it is not close to the air exhaust vent of an air conditioner.
30cm
30cm
30cm
20cm
4
Safety Warning and Cautions
Attention
•
Try not to setup the projector in locations subject to high humidity and dust, or in locations subject to smoke from fires or tobacco smoke.
•
When setting up multiple projectors, make sure there is a gap of at least
50 cm between the projectors. Also, make sure that the heat from the air exhaust vent does not go into the air intake vent.
• The cable connecting the power supply unit and the image projection unit is wrapped in plastics at the time of purchase. Make sure you remove the plastics before using the projector.
a
We recommend setting the focus, zoom, and lens shift at least 20 minutes after you start the projection, because images are not stable right after turning on the projector.
Warning and Cautions on Usage
Warning
• Do not cover the projector's air intake vent or air exhaust vent. If either of the vents is covered, the internal temperature could rise and cause a fire.
• Do not look into the lens while projecting. The powerful light emitted could cause damage to eyesight. Take particular care when there are children present. When turning on the projector at a distance using the remote control, make sure there is no one looking into the lens.
• During projection, do not block the light from the projector with a book and so on.
If the light from the projector is blocked, the area on which the light shines becomes hot which could cause it to melt, burn, or start a fire. Also, the lens may get hot due to the reflected light which could cause the projector to malfunction. To stop projection, use the A/V Mute function, or turn off the projector.
• Do not open the projector's case. Never disassemble or remodel the projector.
There are high-voltage components inside the projector that could cause fire, electric shock, or an accident.
• If an error occurs, disconnect the power cord from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson
Projector Contact List. If you continue using the projector as it is, it could cause an electric shock, fire, or even damage to eyesight.
s
Epson Projector Contact List
Caution
Do not place objects that may become warped or otherwise affected by heat near the air exhaust vent and do not put your face or hands near the vent while projection is in progress.
5
Safety Warning and Cautions
Attention
•
Try not to touch the lens section with your hand or fingers. If fingerprints or oils are left on the surface of the lens, projection quality deteriorates.
•
When storing, make sure you remove the batteries from the remote control.
If the batteries are left in the remote control for an extended period of time, they may leak.
a •
About the LCD panel
- The LCD panel may contain pixels that are missing or appear bright all the time. This is not a sign of an error.
- When a high-powered laser beams through the surface of the projection lens even when it is not being used, it can cause a malfunction in the
LCD panel.
- If the same image is projected for an extended period, burning may occur on the LCD panel. Use Refresh Mode to reduce burning.
s
• About the light source
The projector uses a laser as the light source. The laser has the following characteristics.
- Depending on the surroundings, the output of the light source may be reduced. The output is reduced a lot when the temperature gets too high.
- The output of the light source is reduced the longer it is used. You can change the relationship between usage time and reduction in output in
Brightness Settings .
s
a •
Light Source Calibration
- Whenever the usage time reaches 100 hours, Light Source Calibration starts automatically when the projector is turned off. However, this does not start automatically when the projector is used continuously for more than 24 hours, or when direct shutdown is used regularly. Execute with Run Now , or set Light Source Calibration using the scheduling function to adjust the light source periodically.
s Reset - Light Source Calibration
s
"Setting an Event Schedule" p.71
- If you do not want to start Light Source Calibration automatically, set
Run Periodically to Off .
s Reset - Light Source Calibration - Run Periodically
- Execute Light Source Calibration to correct the white balance in the light source.
6
Safety Warning and Cautions
Warning and Cautions on the Laser
Warning
• Laser warning labels are attached inside the projector and on the side of the projector.
Inside
Warning
Side
Warning
• Do not open the projector's case. The projector contains a high-powered laser.
• Do not look into the light emitted from the projection lens while projecting.
(Based on the RG2 IEC/EN 62471-5: 2015)
Caution
• This projector is a Class 1 laser product that complies with the IEC/
EN60825-1: 2014 international standard for lasers.
• Do not disassemble the projector when disposing of it. Dispose according to your local or national laws and regulations.
7
Safety Warning and Cautions
Notes on Transporting
There are many glass parts and precision components inside the projector.
To prevent damage due to impacts when transporting, handle the projector as follows.
Attention
• To move it closer, turn off the projector and unplug all of the wires.
• When Transporting
As well as the precautions above, prepare the following and contact your courier.
- Make sure there is no SD card inserted in the projector.
- Tighten the ball joint fixing screw completely to prevent the projector from moving during transportation.
- Protect the outside of the projector so that it does not receive any impacts during transportation.
- Place the projector in a sturdy box and indicate on the box that it is a precision instrument.
8
Contents
9
Notations Used in This Guide . . . . . . . . . . . . . . . . . . . . . . . . 2
Part Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Projector Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Connecting to Various Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Setting Up the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Default Projector Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Changing the Projection Mode Using the Remote Control . . . . . . . . . . . . . . . . 28
Changing the Projection Mode Using the Menus . . . . . . . . . . . . . . . . . . . . . . 28
Selecting the Language for the Projector Menus . . . . . . . . . . . . . . . . . . . . . . . . 29
Turning On/Off the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Switching to the Target Image by Remote Control . . . . . . . . . . . . 36
Operating the Projector Using a Mobile Device or Computer
Operating Using Epson iProjection (iOS/Android) . . . . . . . . . . . . . . . . . . . . . . . . 40
Operating Using Epson Web Control (Web Browser) . . . . . . . . . . . . . . . . . . . . . . 40
OSD Control Pad screen (Epson Web Control only) . . . . . . . . . . . . . . . . . . . . . 44
Adjusting the projected images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Selecting the Projection Quality (Selecting Color Mode) . . . . . . . . . . . . . . . . . . . 52
Contents
10
Setting the Amount of Light of the Projected Image . . . . . . . . . . . . . . . . . . . . . . 54
Changing the Aspect Ratio of the Projected Image . . . . . . . . . . . . . . . . . . . . . . . 54
Adjusting the Gamma Value of the Projected Image . . . . . . . . . . . . . . . . . . . . . . 55
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Hiding the Image and Sound Temporarily (A/V Mute) . . . . . . . . . 58
Projecting One Image from Multiple Projectors (Multi-
Adjusting the Points Where the Images Overlap (Edge Blending) . . . . . . . . . . . . . 62
Adjusting uneven colors (Color Uniformity) . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Adjusting the tint (Color Matching) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Playing the Same Image Simultaneously on Multiple Projectors
(Synchronized Playback) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Setting an Event Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Managing Users (Password Protection) . . . . . . . . . . . . . . . . . . . . . . 73
Using the Projector on a Network
Wired Network Projection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Wireless Network Projection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Selecting Wireless Network Settings Manually . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Selecting Wireless Network Settings in Windows . . . . . . . . . . . . . . . . . . . . . . . . 83
Supported Client and CA Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Using a QR Code to Connect a Mobile Device . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Importing a Web Server Certificate Using the Menus . . . . . . . . . . . . . . . . . . . . . . 88
Supported Web Server Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Setting a certificate using a Web browser . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Using the Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Notes on operating the Network menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Contents
11
Reflecting saved settings to other projectors . . . . . . . . . . . . . . . . . . . . . . . . 116
Reading the Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Moving images are not displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Images are fuzzy, out of focus, or distorted . . . . . . . . . . . . . . . . . . . . . . . . . 127
Interference or distortion appear in images . . . . . . . . . . . . . . . . . . . . . . . . . 127
Burning appears on the LCD panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
The projector does not turn on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Solutions When Wireless Authentication Fails . . . . . . . . . . . . . . . . . . . . . . . 130
Solutions When You Cannot Access the Projector using a Web browser . . . . . . 130
Email is not received even if a problem occurs in the projector . . . . . . . . . . . . 131
Solutions When the Image Contains Static During Network Projection . . . . . . . 131
No sound can be heard or the sound is faint . . . . . . . . . . . . . . . . . . . . . . . . 132
The remote control does not work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
I want to change the language for messages and menus . . . . . . . . . . . . . . . . 133
Solutions to Password Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
The battery that saves your clock settings is running low. is displayed . . . . . . . 133
Detailed logs and error message are not displayed . . . . . . . . . . . . . . . . . . . . 133
Cleaning the Air Intake Vent and the Air Exhaust Vent . . . . . . . . . . . . . . . . . . . . 138
Image Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Monitoring and Controlling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Using the Mail Notification Function to Report Problems . . . . . . . . . . . . . . . . . . 142
®
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Operating a projector from your computer . . . . . . . . . . . . . . . . . . . . . . . . . 144
Contents
List of Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Screen Size and Projection Distance . . . . . . . . . . . . . . . . . . . . . . . . 155
Supported Monitor Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
List of Safety Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
12
Introduction
This chapter explains the names for each part.
Part Names and Functions
The following sections explain the projector parts and their functions.
Front
A Power unit
B Image projection unit
Name
A Projection lens
Function
Images are projected through here.
Warning
Do not look into the lens while projecting. This could cause damage to eyesight due to the power‐ ful light emitted.
B Air intake vent Takes in air to cool the projector internally.
s
"Cleaning the Air Intake Vent and the Air Exhaust
C Ball joint Use this to change the projection angle.
s
"Adjust the projection angle using the ball joint" p.22
D Ball joint fixing screw Screw to secure the ball joint in place.
14
Part Names and Functions
Name
E Indicators
F Remote receiver
Function
Displays the projector's status.
s
"Reading the Indicators" p.119
Receives signals from the remote control.
Rear
15
Name
A Air exhaust vent
B Interface
C [ t ] button
Function
Exhaust vent for air used to cool the projector internally.
Caution
While projecting, do not put your face or hands near the air exhaust vent, and do not place objects that may become warped or damaged by heat near the air exhaust vent. Hot air from the air exhaust vent could cause burns, warping, or accidents to occur.
s
"Cleaning the Air Intake Vent and the Air Exhaust
s
Turns the projector on or off.
Part Names and Functions
Name
D Cable holder
Function
Insert the cable clamp so that the power cord does not disconnect under its own weight.
Interface
16
E Power inlet Connects the power cord to the projector.
F Power adapter cover The cover for the power port and the power button.
A
B
C
D
Name
LAN port
HDMI port
SD card slot
Audio Out port
E USB-A port (dedicated power supply/1,200 mA)
Function
Connects a LAN cable to connect to a network.
Supports Art-Net.
s
Inputs video signals from HDMI compatible video equipment and computers.
Insert an SD card into this slot.
Outputs audio from the currently projected image to an external speaker.
Connects and supplies power to a USB cable. This cannot be used to transfer data.
Part Names and Functions
Name
F Cable holder
Function
Insert the cable clamp so that the HDMI cord does not disconnect under its own weight.
Top
17
Name
A Direct Mount fixing points (four points)
B Lighting Track Mount fixing points (seven points)
C Floor Stand fixing points (six points)
Function
Install the Direct Mount when suspending the projector from a ceiling or mounting on a wall.
s
Install the optional Lighting Track Mount when installing the projector on a lighting track.
s
s
"List of Optional Accessories" p.154
Install the optional Floor Stand when placing the projector on the floor.
s
s
"List of Optional Accessories" p.154
Part Names and Functions
Remote Control
18
Name
A [ t ] button
B [HDMI] button
C [LAN] button
D Numeric buttons
E
F
I
[ID] button
[Menu] button
G
[ ][ ][ ][ ] buttons
H
[ ] button
[User] button
J [Focus] button
K [Zoom] button
L [Pattern] button
Function
Turns the projector on or off.
Changes to images from the HDMI input port.
Switches the image source between the network connected devices.
•
Plays your favorite playlist (1 to 9 only).
s
"Playing Your Favorite Playlist" p.38
•
Enter the Password.
s
"Managing Users (Password Protection)" p.73
Hold down this button and press the numeric buttons to select the ID for the projector you want to operate using the remote control.
s
"Setting the Projector ID" p.61
Displays and closes the Configuration menu.
s
"Using the Configuration Menu" p.92
When the Configuration menu is displayed, pressing these buttons selects menu items and setting values.
s
"Using the Configuration Menu" p.92
When the Configuration menu is displayed, it accepts and enters the current selection and moves to the next level.
s
"Using the Configuration Menu" p.92
Performs settings assigned in the User Button setting in the projector's Configuration menu.
s
Press to adjust the focus.
s
Press to adjust the zoom.
s
"Adjusting the Image Size" p.49
Displays a test pattern.
s
"Displaying a Test Pattern" p.48
Part Names and Functions
M
N
O
P
Q
R
S
T
U
[
[
Name
[Keystone] button
[SD Viewer] button
[Effect] button
[Volume] buttons b ][ a ]
[Default] button
[Esc] button
[A/V Mute] button
] button
[Spotlight] button
V Remote control lightemitting area
Function
Corrects distortion in the projected image.
s
"Correcting Distortion in the Projected Image" p.49
Displays the list of playlists.
s
Use the Overlay Effect function to change the shape and color of the image.
s
[ b ] Increases the volume.
[ a ] Decreases the volume.
s
Enabled when [Default]: Reset is displayed on the
Configuration menu guide. The settings being adjusted are returned to their default values.
s
"Using the Configuration Menu" p.92
• Stops the current function.
•
If pressed when the Configuration menu is displayed, it moves to the previous level.
s
"Using the Configuration Menu" p.92
Turns the video and audio on or off.
s
"Hiding the Image and Sound Temporarily (A/V
Plays the playlist on the SD card.
s
Switches to Spotlight mode.
s
Outputs remote control signals.
19
Preparing the Projector
Follow the instructions in these sections to set up your projector.
Projector Placement
Types of Installation
You can install the projector in the following ways.
Suspending from a ceiling or mounting on a wall
•
Use the Direct Mount supplied when suspending from a ceiling or installing on a wall.
•
You need the optional Lighting Track Mount when installing on a lighting track.
•
When suspending from a ceiling or installing on a wall, we recommend a horizontal ceiling or a vertical wall.
See the Installation Manual for details.
Make sure you select the correct Projection option in the projector's
Extended menu according to the installation method being used.
21
Installing on a floor or table
•
You need the optional Floor Stand when installing on the floor or a table.
•
Do not install on the floor or a table using the supplied Direct
Mount.
a
Place the projector in a level and stable location.
Projector Placement a •
The default Projection setting is Front/Ceiling .
•
You can change the Projection setting as follows by pressing down the [A/V Mute] button on the remote control for about five seconds.
Front/Ceiling , Rear , Rear/Ceiling , Front
•
Install the projector within the recommended projection range.
s
"Screen Size and Projection Distance" p.155
•
You can rotate the ball joint 360˚ horizontally and 90˚ vertically.
You can also tilt the image 90˚ to the portrait orientation.
a Press the [ t
] button on the remote control to turn on the projector.
s
"Turning On the Projector" p.34
b Loosen the ball joint fixing screw using a hexagonal wrench.
22
Attention
• If you loosen the screw while the image projection unit is tilted, the image projection unit may move suddenly under its own weight.
When loosening the screw, make sure you support the projector's image projection unit so that the projector does not move suddenly.
s
"Setting the Image Orientation (Projection)" p.28
Adjust the projection angle using the ball joint
Adjust using the ball joint to change the projection angle.
•
Do not grip the ball joint when loosening the screw. Otherwise, your fingers could get trapped.
c Adjust the projection angle.
Projector Placement
Attention
•
Do not apply excessive force to the cables connected to the projector.
•
Do not wind cables around the ball joint. Otherwise, the cables could be damaged.
d After you finish making adjustments, tighten the ball joint fixing screw that you loosened.
Caution
• Make sure you do not trap your fingers in the ball joint.
•
Do not force the ball joint to move after tightening the ball joint fixing screw.
Attention
Make sure you support the bottom of the image projection unit so that it does not move, and tighten the screw with the hexagonal wrench supplied
(diagonal size 5.0 mm).
a •
Adjust the size and focus after changing the projection position.
s
"Adjusting the Image Size" p.49
s
•
Displaying the test pattern makes it easier to adjust the projection position.
s
"Displaying a Test Pattern" p.48
23
Connecting to Various Devices
Hub
Audio IN
LAN
SD
A
B
C
When Connecting to a Wired Network
Connect a LAN port on network hubs or other equipment to the projector's LAN port with a commercially available 100BASE-TX or 10BASE-T LAN cable.
a
To prevent malfunctions, use a category 5 or higher shielded LAN cable.
When Connecting to a Computer or Video Source
Connect the HDMI port on the computer or video source to the projector's HDMI port.
You can send the computer's or the video source's audio with the projected image.
When connecting to an external speaker
Connect the external speaker to the projector's Audio Out port using a commercially available audio cable.
Attention
Do not connect headphones or earphones to the projector. Excessive sound pressure may cause hearing loss.
24
Connecting to Various Devices
D When inserting an SD card
Insert a commercially available SD card into the projector's SD card slot.
a • The projector supports SDHC cards of Class 10 or higher with a maximum of 32 GB.
• Make sure you use SD cards in FAT16 or FAT32 format.
Attention
• If the input source is on when you connect it to the projector, it could cause a malfunction.
• If the orientation or shape of the plug differs, do not try to force it in. The device could be damaged or could malfunction.
a
If the source you want to connect to has an unusually shaped port, use the cable supplied with the device or an optional cable to connect to the projector.
25
Setting Up the Remote Control
Inserting Batteries into the Remote Control
The remote control uses the two AA batteries that came with the projector.
Attention
Make sure you read the following manual before handling the batteries.
s
Safety Instructions a Remove the battery cover.
Caution
Check the positions of the (+) and (-) marks inside the battery holder to ensure the batteries are inserted the correct way.
If the batteries are not used correctly, they could explode or leak causing a fire, injury, or damage to the product.
c Replace the battery cover and press it down until it clicks into place.
26 b Insert the batteries with the + and - ends facing as shown.
Setting Up the Remote Control
Remote control operating range
60° 60°
7m a
To restrict reception of the operation signals from the remote control, set Remote Receiver .
s Settings - Remote Receiver
27
Default Projector Settings
28
Setting the Image Orientation (Projection)
Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly.
When the projector is suspended from a ceiling, the image directions for each projection mode are as follows.
Front/Ceiling (Default) Rear
Rear/Ceiling Front
The image disappears briefly and reappears flipped top-to-bottom.
c To change projection back to the original mode, hold down the [A/V Mute] button for 5 seconds again.
Changing the Projection Mode Using the Menus
You can change the projection mode to flip the image over top-to-bottom and/or left-to-right using the projector menus.
a Turn on the projector and display an image.
s
"Turning On the Projector" p.34
b Press the [Menu] button on the remote control.
Changing the Projection Mode Using the Remote Control
You can change the projection mode to flip the image over top-to-bottom.
a Turn on the projector and display an image.
s
"Turning On the Projector" p.34
b Hold down the [A/V Mute] button on the remote control for 5 seconds.
c Select Extended , and then press the [ ] button.
Default Projector Settings d Select Projection , and then press the [ ] button.
Selecting the Language for the Projector Menus
If you want to view the projector's menus and messages in another language, you can change the Language setting.
a Turn on the projector and your computer.
s
"Turning On the Projector" p.34
b Press the [Menu] button on the remote control.
29 c Select Extended , and then press the [ ] button.
e f
Select a projection mode, and then press the [ ] button.
Press the [Menu] button or the [Esc] button to close the menu.
Default Projector Settings d e f
Select Language , and then press the [ ] button.
Select the language you want to use, and then press the [ ].
Press the [Menu] button or the [Esc] button to close the menu.
Setting the Date and Time
You can set the date and time for the projector. The set date and time is used for the schedule function.
s
"Setting an Event Schedule" p.71
a • When you turn on the projector for the first time, the message "Do you want to set the time?" is displayed. When you select Yes , the screen from step 5 is displayed.
• When Schedule Protection is set to On in Password Protection , settings related to the date and time cannot be changed. You can make changes after setting Schedule Protection to Off .
s
"Managing Users (Password Protection)" p.73
a Turn on the projector.
s
"Turning On/Off the Projector" p.34
b Press the [Menu] button on the remote control.
s
"Using the Configuration Menu" p.92
c d e
Select Operation from Extended .
Select Date & Time , and then press the [ ] button.
Make settings for the date and time.
Use the soft keyboard to enter the date and time.
s
"Soft keyboard operations" p.103
Date & Time
Submenu Function
Date
Time
Set today's date.
Set the current time.
Time Difference (UTC) Set the time difference from Coordinated
Universal Time.
Set The settings made in Date & Time are applied.
Daylight Saving Time
Submenu Function
Daylight Saving Time Set whether or not ( On / Off ) to activate the daylight saving time.
DST Adjustment (min) adjusts the time difference between the standard time and daylight saving time.
30
Default Projector Settings
31
Submenu
DST Start
DST End
Set
Function
Set the date and time to start the daylight saving time.
Set the date and time to end the daylight saving time.
The settings made in Daylight Saving Time are applied.
Internet Time
Submenu
Internet Time
Internet Time Server
Set
Function
Set to On to update the time automatically through an Internet time server.
Input the IP address for an Internet time server.
The settings made in Internet Time are applied.
a
When changing settings, make sure you select Set , and then press the [ ] button.
f Press the [Menu] button to finish making settings.
Other Settings
Settings related to basic operations
Purpose
To start/stop projection by turning on/off the main power or plugging in or unplugging the power plug of the projector.
To operate the projector by communication command even when the power of the projector is off.
Turn off the power by pressing the
[ t ] button once.
Setting Methods
Set Direct Power On to On . (Default value: Off ) s Extended - Operation - Direct Power
On
The projector can be powered off directly by the breaker because it supports the direct shutdown function.
Set Standby Mode to Communication On .
(Default value: Communication Off ) s Extended - Standby Mode - Standby Mode
Set Standby Confirmation to Off . (Default value:
On ) s Extended - Display - Standby Confirmation
Settings related to display
Purpose
To disable the display of the message on the projection screen when switching the source.
Setting Methods
Set Messages to Off . (Default value: On ) s Extended - Display - Messages
You can check the warning settings by the way the indicators are displayed.
s
"Reading the Indicators" p.119
Dialogs related to operations and behaviors, laser warnings, termination of Message Broadcasting for Epson Projector Management, and projector
ID are displayed.
Default Projector Settings
Purpose
To display the User's Logo when you turn on the projector.
Setting Methods
Startup Screen : Set whether or not ( On / Off ) to display the user logo when the projector is turned on. (Default value: On ) s Extended - Display - Startup Screen
32
Basic Usage
This chapter explains how to project and adjust images.
Turning On/Off the Projector
Turning On the Projector
Before turning on the projector, connect your computer or video equipment to the projector.
s
"Connecting to Various Devices" p.24
a Connect the projector to an electrical outlet with the power cord.
The projector's On/Standby indicator turns blue (it is in standby mode). This indicates that the projector is receiving power, but is not yet turned on.
a
When the projector is installed on a lighting track, the projector enters standby status when you turn on the power to the lighting track.
b Press the [ t
] button on the projector or the [ t
] button on the remote control to turn on the projector.
The Status indicator flashes blue (warm-up state). Once the projector is warmed up, the Status indicator stops flashing and turns blue.
If the image is not projected, check the following.
•
Turn on the connected computer or video equipment.
•
When using a laptop computer, change the screen output of the computer.
•
Insert media such as a DVD and play it back.
•
Press the button for the input source that you want to project by using the remote control.
Warning
•
Do not look into the projector's lens during projection. Doing so may damage your eyes. Be especially careful if children are present.
•
During projection, do not block the light from the projector with a book and so on. If the light from the projector is blocked, the area on which the light shines becomes hot which could cause it to melt, burn, or start a fire. Also, the lens may get hot due to the reflected light which could cause the projector to malfunction. To stop projection, use the A/V Mute function or turn off the projector.
a •
If Direct Power On is set to On in the Extended menu, the projector automatically turns on when the power cord is connected to it. When the power cord is plugged in, note that the projector turns on automatically in cases such as recovery from a power outage.
s Extended - Operation - Direct Power On
•
If an image signal from the source selected in Auto Power On is input, the projector automatically turns on.
s Extended - Operation - Auto Power On
34
Turning On/Off the Projector
Turning Off the Projector
a • To ensure a long projector service life, turn off the projector when you are not using it. The light source's operating life varies depending on the Configuration menu settings, environmental conditions, and usage conditions. The brightness of the projected image drops as projection time elapses.
• The projector can be powered off directly by the breaker because it supports the direct shutdown function.
• Whenever the usage time reaches 100 hours, Light Source
Calibration starts automatically when the projector is turned off.
However, this does not start automatically when the projector is used continuously for more than 24 hours, or when direct shutdown is used regularly. Execute with Run Now , or set Light Source
Calibration using the scheduling function to adjust the light source periodically.
s Reset - Light Source Calibration
s
"Setting an Event Schedule" p.71
• If you do not want to start Light Source Calibration automatically, set Run Periodically to Off .
s Reset - Light Source Calibration - Run Periodically
• When Light Source Calibration is enabled, turn on the projector at least 20 minutes before the event.
• Execute Light Source Calibration to correct the white balance in the light source.
35 a Press the [ t
] button on the projector, or the [ t
] button on the remote control.
The shutdown confirmation screen is displayed.
b Press the [ t ] button again, or the [ t ] button on the remote control. (To cancel, press any other button.)
The projected image disappears and the Status indicator turns off.
c To transport or store the projector, make sure the On/Standby indicator is blue (but not flashing) and the status indicator is off, then unplug the power cord.
a
When the projector is installed on a lighting track, turn off the power to the lighting track.
Switching to the Target Image by Remote Control
Press the button of the input source that you want to project.
The input ports for the buttons are shown below.
Remote control
Input Port
B Switches to images from a computer or mobile device connected over a network.
D Switches to Spotlight mode.
36
Using Spotlight
You can use the projector's projection light as a Spotlight.
a Press the [Spotlight] button on the remote control.
Switches to Spotlight mode.
b Press the [Effect] button on the remote control to change the color and shape.
See the following Web site for details.
s
37
Playing a Playlist
You can play a playlist saved on the SD card.
38
Playing a Playlist on an SD Card
Press the [ ] button on the remote control to play a playlist saved on the SD card. When an event has been scheduled, the playlist is played according to the schedule in the time table.
s
You can create a playlist using Epson Projector Content Manager, Epson iProjection (iOS/Android), or a Web browser.
Download the Epson Projector Content Manager software from the following website.
http://www.epson.com
See the "Epson Projector Content Manager Operation Guide" for details on the operation method for Epson Projector Content Manager.
Insert the SD card containing the playlist into the projector.
s
"Connecting to Various Devices" p.24
Attention
In the following situations, do not unplug the SD card or the power cord from the projector.
Otherwise, data recorded on the SD card may be damaged.
•
While playing a playlist
•
While displaying a playlist
Playing Your Favorite Playlist
You can assign playlists to each of the numeric buttons (1 to 9) on the remote control. By pressing the button to which the playlist is assigned, you can easily access the playlist you want to play.
a
Use Epson Projector Content Manager, Epson iProjection
(iOS/Android), or a Web browser to assign playlists to the buttons on the remote control.
Playing a Playlist
Selecting and Playing a Playlist
You can specify a playlist saved on the SD card and play it.
a Press the [SD Viewer] button on the remote control.
A list of playlists saved on the SD card is displayed.
b Use the [ ][ ][ ][ ] buttons to select the playlist you want to play.
The selected playlist is played.
39
Operating the Projector Using a Mobile Device or Computer
40
You can operate the projector and edit playlists from mobile devices or computers.
If you are using a mobile device, use Epson iProjection (iOS/Android) to operate the projector.
You can download Epson iProjection (iOS/Android) for free from the App
Store or Google Play. Make sure you use version 3.0 or later.
a
Any fees incurred when communicating with the App Store or Google
Play are the responsibility of the customer.
If you are using a computer, use the Epson Web Control function to operate the projector from a Web browser.
For Web browsers, use Internet Explorer 11.0 or later (except for Metro) or
Microsoft Edge. For Mac, use Safari.
a
If you set Standby Mode to Communication On , you can use the
Web browser to make settings and perform control even if the projector is in standby mode (when the power is off).
s Extended - Standby Mode
Attention
In the following situations, do not unplug the SD card or the power cord from the projector.
Otherwise, data recorded on the SD card may be damaged.
•
While displaying the playlist screen
•
While displaying the SD card screen
Make sure your device and projector are ready for the network connection.
a Connect your device to the same network as the connected projector.
The connection method varies depending on the device. See the manual supplied with your device for details.
b c
Start Epson iProjection on your device.
Press Remote from the menu.
The Remote screen is displayed.
s
a •
When you press Remote in Epson iProjection, you may be prompted to enter your user name and password.
The user name is "EPSONWEB"; the default password is "admin"
•
You cannot change the user name. You can change the password in the Network menu from the Configuration menu.
s Network - Basic - Web Control Password
•
You must enter the user name for Web Control Password even when the password is disabled.
Operating Using Epson Web Control (Web
Browser)
Use the following procedure to display the Home screen.
Make sure your device and projector are ready for the network connection.
Operating Using Epson iProjection (iOS/Android)
Use the following procedure to display the Remote screen.
Operating the Projector Using a Mobile Device or Computer a
If your Web browser is set up to connect through a proxy server, the
Home screen cannot be displayed. To display Web Control, you need to make settings so that a proxy server is not used for a connection.
a Connect your device to the same network as the connected projector.
The connection method varies depending on the device. See the manual supplied with your device for details.
b c
Start the Web browser on your device.
Enter the IP address for the connected projector in the URL field, and then connect.
The Home screen is displayed.
A Remote s
B Playlists s
C OSD Control Pad s
"OSD Control Pad screen (Epson Web Control only)" p.44
D Settings
You are moved to the Settings screen.
E Advanced
You are moved to the Advanced screen.
F Crestron Connected s
"About Crestron Connected ® " p.144
G SD Card s
H Time Table s
a • When performing the functions from the Home screen, you may be prompted to enter the user name and password.
The user name is "EPSONWEB"; the default password is "admin"
• You cannot change the user name. You can change the password in the Network menu from the Configuration menu.
s Network - Basic - Web Control Password
• You must enter the user name for Web Control Password even when the password is disabled.
• You can only set the following items from the Advanced screen.
- Monitor Password (up to 16 single-byte alphanumeric characters) s Network - Basic - Monitor Password
- IPv6 Settings (Manual) s Network - IPv6 Settings
- Add HTTP port (for the port number used for Web control, use anything except for 80 (default), 443, 843, 3620, 3621, 3625, 3629,
4352, 4649, 5357, 6454, 10000, 10001, 41794) s Network - Others
41
Operating the Projector Using a Mobile Device or Computer
Viewing Each Screen
Remote screen
You can perform basic projector operations.
Epson iProjection Epson Web Control
Playlists screen
You can control your playlists.
Epson iProjection Epson Web Control
42
A Moves to the Home screen. (Epson Web Control only)
B Create a new playlist.
C Play, stop, set effects, use A/V mute, and adjust the volume for the playlist.
D Edit and copy playlists, and add or delete your favorite playlists.
A Moves to the Home screen. (Epson Web Control only)
B Turns the projector on or off.
C Switches to the target image.
D Turns the video and audio on or off.
E You can adjust the volume.
F Select your favorite playlist.
Operating the Projector Using a Mobile Device or Computer
SD Card screen
You can operates the SD card inserted in the projector.
Epson iProjection Epson Web Control
Time Table screen
You can browse the time table.
Epson iProjection Epson Web Control
43
A Moves to the Home screen. (Epson Web Control only)
B Transfers data (movies or still images used for playlists) to the SD card.
C Deletes data from the SD card.
A Moves to the Home screen. (Epson Web Control only)
B Turns the time table on or off.
a
By using the Epson Projector Content Manager's time table function, you can specify the date and time to play the playlist.
See the Epson Projector Content Manager Operation Guide for instructions.
Operating the Projector Using a Mobile Device or Computer
OSD Control Pad screen (Epson Web Control only)
You can operate the Configuration menu of the projector.
A Moves to the Home screen. (Epson Web Control only)
B Displays and closes the Configuration menu.
C You can operate the Configuration menu using your finger or mouse.
Flick to select an item, and tap to confirm the selection.
D Enabled when [Default]: Reset is displayed on the Configuration menu guide. The settings being adjusted are returned to their default values.
E Returns to the previous menu level in the Configuration menu.
F Displays information on using the OSD Control Pad.
44
Using Overlay Effect
You can set the following effects for Spotlight or projected images.
•
Blur the edges of the image
•
Change the shape of the image
•
Change the color of the image
•
Adjust the brightness of the image
45
Attention
Do not unplug the SD card or power cord from the projector while operating
Overlay Effect.
Otherwise, data recorded on the SD card may be damaged.
a
You can set Overlay Effect for each input source. For SD cards, you can set effects for each playlist.
Setting the Shape of the Effect
a Press the [Effect] button while projecting Spotlight or images.
b c d
Set Overlay Effect to On .
Select Shape Filter , and then press the [ ] button.
Use the [ ][ ] buttons to select the item you want to set, and then press the [ ] button.
Shape : You can select the shape of the effect from a circle, square, or make a custom shape. If you are not using Shape Filter, select
Off .
Filter Effect : Select whether to mask the color of the mask as well as the inside of the selected shape, or to mask the outside.
Size : Use the [ ][ ] buttons to set Height and Width for the selected shape.
Position : Use the [ ][ ][ ][ ] buttons to set the position in which to display the selected shape.
The following screen is displayed.
Using Overlay Effect a
You can create custom shapes using Epson Projector Content
Manager.
e Press the [Effect] button or the [Menu] button to finish making settings.
Adjusting the Color of the Effect
a Press the [Effect] button while projecting Spotlight or images.
46 d Select Color Filter , and then use the [ ][ ] buttons to select the color you want to set. To set a color that is not available in this setting, select Custom .
e To adjust the color for Custom , select Custom , and then press the
[ ] button.
The following screen is displayed.
f Use the [ ][ ] buttons to select the color, and then use the
[ ][ ] buttons to make the adjustments.
b c
Set Overlay Effect to On .
Select Color Filter , and then press the [ ] button.
Using Overlay Effect g Press the [Effect] button or the [Menu] button to finish making settings.
Adjusting the Brightness of the Overlay Effect
a Press the [Effect] button while projecting Spotlight or images.
47 e Press the [Effect] button or the [Menu] button to finish making settings.
The following screen is displayed.
b c d
Set Overlay Effect to On .
Select Lightness , and then press the [ ] button.
Use the [ ][ ] buttons to adjust the Lightness.
Adjusting the projected images
Displaying a Test Pattern
A test pattern can be displayed to adjust the projection status without connecting video equipment.
a b
Press the [Pattern] button while projecting.
Press the [ ][ ] buttons on the remote control to change test pattern.
48
Standard Cross-hatching
Cross-hatching
R
Cross-hatching
G
Cross-hatching
B Color Bars V Color Bars H Grayscale
Gray Bars V Gray Bars H Checkerboard 1 Checkerboard 2
White Black Aspect Frame
In addition to lens operations, the following image adjustments can be made while the test pattern is being displayed.
Top Menu Name
Image
Settings
Extended
Sub Menu/Items
Color Mode s
White Balance
Advanced
- Gamma s
Dynamic Contrast s
Reset
Keystone s
Brightness Settings
Multi-Projection * s
* Except for Color Uniformity and Scale
Adjusting the projected images
49 a •
To set menu items that cannot be set while the test pattern is being displayed or to fine-tune the projected image, project an image from the connected device.
•
You can also select a test pattern from the Configuration menu.
s Settings - Test Pattern
c Press the [Esc] button to close the test pattern.
Adjusting the Image Size
a Press the [Zoom] (+/-) buttons on the remote control to adjust the zoom.
Correcting the Focus
a Press the [Focus] ( / ) buttons on the remote control to adjust the focus.
a
The focus adjustment screen is displayed in blue so that it is easy to see even if it is out of focus.
b Press the [Esc] button to finish the adjustment.
Correcting Distortion in the Projected Image
You can correct keystone distortion in projected images using one of the following methods.
b Press the [Esc] button to finish the adjustment.
a •
When minimizing the size of the image using the optical zoom, a message is displayed and the projector switches to digital zoom.
•
When maximizing the size of the image using the digital zoom, a message is displayed and the projector switches to optical zoom.
Adjusting the projected images
•
Correcting H/V-Keystone
This allows you to correct distortion in the horizontal and vertical directions independently.
s
"Correcting H/V-Keystone" p.50
b Select H/V-Keystone , and then press the [ ] button.
50
"If this setting is changed, the image may be distorted." is displayed, press the [ ] button.
c Use the [ ][ ] buttons to select the correction method, and then correct using the [ ][ ] buttons.
•
Quick Corner
Correct the four corners independently.
s
Correcting H/V-Keystone
This allows you to correct distortion in the horizontal and vertical directions independently.
a Press the [Keystone] button while projecting.
Adjusting the projected images
Correct the keystone distortion by using V-Keystone and H-
Keystone .
V-Keystone
51
H-Keystone a
When you correct keystone distortion, the projected image may be reduced.
d Press the [Menu] button to finish making corrections.
a
You cannot combine with other correction methods.
Quick Corner
This allows you to correct each of the four corners of the projected image independently.
a b
Press the [Keystone] button while projecting.
Select Quick Corner , and then press the [ ] button.
"If this setting is changed, the image may be distorted." is displayed, press the [ ] button again.
c Use the [ ], [ ], [ ], and [ ] buttons to select the corner you want to adjust, and then press the [ ] button.
a
If the [Esc] button is pressed for approximately two seconds, the confirm default reset screen is displayed.
Select Yes to reset the result of Quick Corner corrections.
Adjusting the projected images d Use the [ ], [ ], [ ], and [ ] buttons to correct the position of the corner.
When you press the [ ] button, the screen shown in step 4 that allows you to select the area to be corrected is displayed.
If the message "Cannot adjust any further." is displayed while adjusting, you cannot adjust the shape any further in the direction indicated by the gray triangle.
a b
Press the [Menu] button while projecting.
Select Color Mode from Image .
52 e f
Repeat steps 3 and 4 as needed to adjust any remaining corners.
Press the [Menu] button to finish making corrections.
Selecting the Projection Quality (Selecting Color
Mode)
You can easily obtain the optimum image quality by selecting the Color
Mode that best corresponds to your surroundings when projecting. The brightness of the image varies depending on the mode selected.
c Select the item you want to set, and then press the [ ] button.
Dynamic : This is the brightest mode. Ideal for use in a bright room.
Normal : This tones down the brightness of the image more than
Dynamic , and provides images with natural colors.
d Press the [Menu] button to finish making settings.
Setting the Brightness
Set the brightness for the light source.
a Press the [Menu] button while projecting.
Adjusting the projected images b Select Brightness Settings from Settings .
c Select Light Source Mode , and then press the [ ] button.
53 d Select the item you want to set, and then press the [ ] button.
Normal : Select this if you do not want to decrease the brightness.
This makes the target usage time approximately 20,000 hours.
Quiet : Select this if you are concerned about the noise made by the fan, This sets the brightness at 50%. This makes the target usage time approximately 20,000 hours.
Extended : Select this to extend the life expectancy of the light source. This sets the brightness at 50%. This makes the target usage time approximately 30,000 hours.
Custom : Select this to set the brightness level within a range of 50 to
100%.
e When Light Source Mode is set to Custom , select Brightness
Level , and then use the [ ][ ] buttons to set the brightness.
a
There may be a margin of error in the Brightness Level .
f Press the [Menu] button to finish making settings.
Adjusting the projected images
54
Setting the Amount of Light of the Projected
Image
By automatically setting the luminance according to the brightness of the displayed image, it lets you enjoy deep and rich images.
a b
Press the [Menu] button while projecting.
Select Dynamic Contrast from Image , and then press the [ ] button.
Changing the Aspect Ratio of the Projected Image
You can change the Aspect Ratio g
of the displayed image.
a •
You can only set the Aspect when the input signal is HDMI.
• The available settings depend on the input source being projected.
a b
Press the [Menu] button while projecting.
Select Aspect from Signal , and then press the [ ] button.
c Select Normal or High Speed , and then press the [ ] button.
The setting is stored for each Color Mode .
d Press the [Menu] button to finish making settings.
c Use the [ ][ ] buttons to select the item you want to set, and then press the [ ] button.
Aspect Mode
Auto
Normal
Explanation
Projects in an appropriate aspect ratio based on information from the signal being input.
Projects while retaining the aspect ratio of the input image.
Adjusting the projected images
55
Aspect Mode
4:3
16:9
Full
Zoom
Native
Explanation
Projects at an aspect ratio of 4:3.
Projects at an aspect ratio of 16:9.
Projects at the full size of the projected screen.
Projects by enlarging the input image to the full width of the projected screen while retaining the aspect ratio.
Areas that exceed the edges of the projected screen are not projected.
Projects to the center of the projected screen at the resolution of the input image. Areas that exceed the edges of the projected screen are not projected.
d Press the [Menu] button to finish making settings.
The aspect mode changes as shown in the tables below.
: The area where the image is not displayed depending on the aspect mode setting.
Aspect Ratio of Input Signal
16:9 4:3 16:10
Auto or Normal
16:9
Zoom
Native *
16:10
Aspect Ratio of Input Signal
16:9 4:3
* The image may differ depending on the resolution of the input signal.
Adjusting the Gamma Value of the Projected
Image
You can adjust differences in the halftone brightness that occurs depending on the connected device.
a
Adjust by projecting a still picture. Gamma cannot be adjusted correctly by using movies.
a b
Press the [Menu] button while projecting.
Select Advanced from Image , and then press the [ ] button.
Full
Adjusting the projected images c d
Select Gamma , and then press the [ ] button.
Use the [ ][ ] buttons to select the correction value, and then use the [ ] button to confirm the selection.
When a larger value is selected, the dark areas of images become brighter, but the color saturation for lighter areas may become weaker.
When a smaller value is selected, you can reduce the overall brightness of the image to make the image sharper.
e Press the [Menu] button to finish making settings.
56
Adjusting the Volume
You can adjust the volume of the audio output from the external speaker connected to the Audio Out port using one of the following methods.
•
Press the [Volume] buttons on the remote control to adjust the volume.
[ b ] Increases the volume.
[ a ] Decreases the volume.
•
Adjust the volume from the Configuration menu.
s
Settings - Volume
Caution
Do not start at high volume.
A sudden excessive volume may cause loss of hearing. Always lower the volume before powering off, so that you can power on and then gradually increase the volume.
57
Hiding the Image and Sound Temporarily (A/V Mute)
You can temporarily hide the projected image and mute the audio. Any sound or video action continues to run, however, so you cannot resume projection at the point that you stopped it.
Each time you press the [A/V Mute] button on the remote control, A/V
Mute turns on or off.
58
Useful Functions
This section describes the Multi-Projection function and synchronized playback.
Projecting One Image from Multiple Projectors (Multi-Projection)
You can setup multiple projectors to project one large image.
You can adjust the difference of brightness and color tone between each projected image to create a seamless screen.
a •
We recommend setting the focus and zoom at least 20 minutes after you start projecting, because images are not stable right after turning on the projector.
•
If the values for Keystone are large, it can be difficult to adjust the image position for overlapping images.
•
The Test Pattern can be displayed to adjust the projection status without connecting video equipment.
s
"Displaying a Test Pattern" p.48
•
If you project a dot by dot image that can be projected without being enlarged or reduced, you can make adjustments precisely.
(3) Adjust the zoom and focus.
s
"Adjusting the Image Size" p.49
s
(4) Adjust the edges of the images.
s
"Adjusting the Points Where the Images Overlap (Edge Blending)" p.62
(5) Select the sections of the images.
s
"Displaying a Scaled Image" p.64
60
Adjustment Procedure
Advance preparation
(1) Turn on all projectors.
(2) Set an ID for all projectors and the remote controls.
s
Adjusting the projected images
(1) Adjusting the projected position.
s
"Adjust the projection angle using the ball joint" p.22
s
"Setting the Image Orientation (Projection)" p.28
s
"Correcting Distortion in the Projected Image" p.49
(2) Adjust the aspect ratio of the images.
s
"Changing the Aspect Ratio of the Projected Image" p.54
Projecting One Image from Multiple Projectors (Multi-Projection)
61
Setting the Projector ID
When an ID is set for the projector and the remote control, you can use the remote control to operate only the projector with a matching ID. This is very useful when managing multiple projectors. You can set up to 9
IDs.
a
Operation using the remote control is possible only for projectors that are within the operating range of the remote control.
s
"Remote control operating range" p.27
Set the projector ID a Press the [Menu] button while projecting.
s
"Using the Configuration Menu" p.92
b c d
Select Multi-Projection from Extended .
Select Projector ID , and then press the [ ] button.
Press the [ ][ ] buttons to select an ID number.
e Press the [ ] button.
f Press the [Menu] button to finish making settings.
Repeat these steps for all the other projectors you want to operate from one remote control.
Selecting the Projector You want to Operate
After setting the projector's ID, select the ID for the projector you want to operate using the remote control.
a Aim the remote control at the target projector and press the [ID] button.
Projecting One Image from Multiple Projectors (Multi-Projection)
The current Projector ID is displayed on the projected screen. It disappears after about 3 seconds.
a •
When you select 0 on the remote control, you can operate all projectors regardless the Projector ID setting.
•
You must select the projector ID from the remote control each time you turn on the projector you have set it to control. When you turn on the projector, 0 is selected as the remote control's projector ID.
•
When you set the Projector ID setting to Off , you can operate the projector using the remote control whichever ID you select on the remote control.
Adjusting the Points Where the Images Overlap
(Edge Blending)
You can fine tune the overlapping areas to make seamless screen.
b While holding the [ID] button, press the number button that matches the ID of the projector you want to operate.
62
The projector you want to operate is selected.
c Press the [ID] button to check if the ID-setting process worked.
You see a message displayed by the projector.
• If the remote control is listed as On , you can operate the projector from the remote control.
• If the remote control is listed as Off , you cannot operate the projector from the remote control. Repeat the steps above to enable the remote control.
a b c
Press the [Menu] button while projecting.
Select Multi-Projection from Extended .
Select Edge Blending , and then press the [ ] button.
The following screen is displayed.
Projecting One Image from Multiple Projectors (Multi-Projection)
63 a
If the guide is not clear, you can change the color of the guide in Guide Color .
f g
Set Pattern Guide to On .
Set Top Edge , Bottom Edge , Left Edge , or Right Edge according to the parts of the image that are overlapped.
The following shows how to set screen (1) as an example.
Submenu
Edge Blending
Top Edge/Bottom
Edge/Left Edge/Right
Edge
Blend Curve
Line Guide
Pattern Guide
Guide Color
Function
Set to On to activate Edge Blending.
Blending : Set to On to activate Edge Blending towards your settings, and the blend range will be shaded.
Blend Range : Adjusts the range to be shaded.
Adjustment is possible at the level of one pixel. The maximum range is 45% of the resolution.
You can select from 3 ways of shading.
Set to On to display a guide on the Edge Blending setting range.
Set to On to display a guide to match the position of the Edge Blending setting range.
Select a combination of guide colors from the three provided.
d e
Set Edge Blending to On .
Set Line Guide to On .
In the example above, you need to adjust the Left Edge because you can see the overlapping areas on the left side of the image (1).
(1) Select Left Edge , and then press the [ ] button.
(2) Select Blending , and then press the [ ] button.
(3) Select On , and then press the [ ] button.
(4) Press the [Esc] button.
Projecting One Image from Multiple Projectors (Multi-Projection)
(5) In Blend Range , adjust the range (3) to be shaded.
The value for when the overlapped range and the guide are in the same position is the best.
(6) Press the [Esc] button.
h Set Blend Curve .
(1) Select Blend Curve , and then press the [ ] button.
(2) Select the amount of shading from 1 to 3 , and then press the [ ] button.
(3) Press the [Esc] button.
i After the settings are complete, set Line Guide and Pattern Guide to Off to finish.
Displaying a Scaled Image
A section of the image is cropped and displayed. This allows you to create one large image by combining images projected from multiple projectors.
a b
Press the [Menu] button while projecting.
Select Multi-Projection from Extended .
a
You can also perform the same operation from Scale in
Signal .
c d
Select Scale , and then press the [ ] button.
Set Scale to On .
64
Projecting One Image from Multiple Projectors (Multi-Projection) e Select Scale Mode .
Zoom Display : Adjusts according to the image currently displayed.
Enlarge
Move
Full Display : Adjusts according to the projector's panel size (the maximum area in which an image can be displayed).
Enlarge
Move
65 f Adjust the scale.
Select the adjustment method with the [ ][ ] buttons, then adjust using the [ ][ ] buttons.
-+ : Enlarges or reduces an image horizontally and vertically at the same time.
Scale Vertically : Enlarges or reduces an image vertically.
Scale Horizontally : Enlarges or reduces an image horizontally.
g The image is clipped and adjusted.
(1) Select Clip Adjustment , and then press the [ ] button.
If you select Clip Range , the range and coordinates of the image that the projector will project is displayed.
(2) Use the [ ], [ ], [ ], and [ ] buttons to scroll the image.
Adjust the coordinates and size of each image while viewing the screen.
a
You can check the displayed area after clipping for the entire image from Clip Range .
h Press the [Menu] button to finish making adjustments.
Adjusting Multiple Projected Images
Adjusting uneven colors (Color Uniformity)
Adjusts the color tone for the whole screen.
a
The color tone may not be uniform even after performing Color
Uniformity.
a Press the [Menu] button while projecting.
Projecting One Image from Multiple Projectors (Multi-Projection) b c
Select Multi-Projection from Extended .
Select Color Uniformity , and then press the [ ] button.
f g h i
Use the [ ][ ] buttons to set the adjustment level.
Press the [Esc] button to return to the previous screen.
Select Start Adjustments , and then press the [ ] button.
Select the area you want to adjust, and then press the [ ] button.
Adjust the outer areas first, and then adjust the whole screen.
66
Color Uniformity : Turns Color Uniformity On or Off .
Adjustment Level : There are eight levels from white, through gray, and up to black. You can adjust each level individually.
Start Adjustments : Starts adjusting Color Uniformity.
Reset : Resets all adjustments and settings for Color Uniformity to their default values.
a
The image may become distorted while adjusting Color
Uniformity . The image is restored once adjustments are complete.
d e
Set Color Uniformity to On .
Select Adjustment Level , and then press the [ ] button.
j Use the [ ][ ] buttons to select the color, and then use the
[ ][ ] buttons to make the adjustments.
Press the [ ] button to weaken the color tone. Press the [ ] button to strengthen the color tone.
Projecting One Image from Multiple Projectors (Multi-Projection) k l
Return to step 5 and adjust each level.
Press the [Menu] button to finish making adjustments.
67
Adjusting the tint (Color Matching)
Adjust the color for each image.
Turn on all of the projectors, and then adjust Color Matching from the
Extended menu for each projector. Adjust so that the colors and brightness are uniform for the entire projected image.
a b c
Press the [Menu] button while projecting.
Select Multi-Projection from Extended .
Select Color Matching , and then press the [ ] button.
Projecting One Image from Multiple Projectors (Multi-Projection)
The following screen is displayed.
68 f Select Brightness , and then use the [ ][ ] buttons to adjust the brightness.
g h
Return to step 1 and adjust each level.
Press the [Esc] button to return to the previous screen.
Half of the overlapped area is displayed in black so that it is easy to check the edge of the image.
Adjustment Level: There are eight levels from white, through gray, and up to black. You can adjust each level individually.
Red, Green, Blue: Adjusts the tone for each color.
Brightness: Adjusts the image brightness.
a
Whenever the [ ] button is pressed, the screen changes between the projected image and the adjustment screen.
d Select Adjustment Level , and then use the [ ][ ] buttons to set the adjustment level.
e Select Red , Green , or Blue , and then press the [ ][ ] buttons to adjust the color tone.
Playing the Same Image Simultaneously on Multiple Projectors (Synchronized Playback)
69
You can play the same playlist at the same time on multiple projectors.
Starting Synchronized Playback
a b c
Insert an SD card into the projector.
Press the [ ] button on the remote control.
Synchronized playback starts at the date/time specified in the time table.
Create and schedule playlists using Epson Projector Content Manager. See the "Epson Projector Content Manager Operation Guide" for details on the operation method for Epson Projector Content Manager.
Set the projector name and the correct date/time in advance for all projectors that will be performing synchronized playback.
s Basic - Projector Name
s
"Setting the Date and Time" p.30
a • The playback timings may change depending on the network status.
We recommend connecting over a wired LAN.
• You can also create playlists using Epson iProjection (Android/iOS) or a Web browser.
s
"Operating the Projector Using a Mobile Device or Computer" p.40
• See the following to adjust the color for multiple projectors that are projecting side-by-side.
s
"Adjusting uneven colors (Color Uniformity)" p.65
Saving a User's Logo
Set the image (User's Logo) you want to display when the projector is turned on. You can also display the User's Logo when the projector is not receiving an input signal.
You can select a photo, graphic, or company logo as the user's logo, which is useful in identifying the projector's owner to help deter theft. You can also set password protect for the User's Logo so that it cannot be changed.
a
Once a User's Logo has been saved, the logo cannot be returned to the factory default.
a Project the image you want to save as the User's Logo, and then press the [Menu] button.
s
"Using the Configuration Menu" p.92
b Select User's Logo from Extended .
a •
When User's Logo Protection from Password Protection is set to On , a message is displayed and the User's Logo cannot be changed. Perform operations after setting User's Logo
Protection to Off .
s
"Kinds of Password Protection" p.73
•
If you select Keystone or Aspect while performing User's
Logo , the function currently being executed is temporarily paused.
c When the message "Choose this image as the User's Logo?" is displayed, select Yes .
a
When you press the [ ] button, the screen size may change depending on the signal to match the actual resolution of the image signal.
70 d Move the box to select the part of the image to use as the User's
Logo.
a
You can save at 400x300 dots in size.
e When you press the [ ] button and the message "Select this image?" is displayed, select Yes .
f g
Select the zoom factor from the zoom setting screen.
When the message "Do you save this image as the User Pattern?" is displayed, select Yes .
The image is saved. After the image has been saved, the message
"Completed." is displayed.
a
When a User's Logo is saved, the previous User's Logo is erased.
Setting an Event Schedule
You can schedule turning the projector power on/off and switching the input source, as events in the schedule. Registered events are executed automatically at the specified time on the specified dates or weekly.
You can register up to 30 Schedule events.
Warning
Do not place flammable objects in front of the lens. If you schedule the projector to turn on automatically, flammable objects in front of the lens could catch on a fire.
a • If the Schedule Protection password is set to On , on the Password
Protection screen, you need to set it to Off first.
• Light Source Calibration does not start if the projector is used continuously for more than 24 hours, or regularly turned off by shutting off the power outlet. Execute with Run Now , or set Light
Source Calibration using the scheduling function to adjust the light source periodically.
s Reset - Light Source Calibration
• If you do not want to start Light Source Calibration automatically, set Run Periodically to Off .
s Reset - Light Source Calibration - Run Periodically
• When Light Source Calibration is enabled, turn on the projector at least 20 minutes before the event.
• Execute Light Source Calibration to correct the white balance in the light source.
a Press the [Menu] button while projecting.
s
"Using the Configuration Menu" p.92
b c
Select Schedule Settings from Extended , and then press [ ].
Select Add New , and then press the [ ] button.
71 d Set the schedule.
Submenu Name
Event Settings
Date / Time Settings
Function
Select an operation of the projector when the event is executed. Select No Change for items that you do not want to change when the event occurs.
You can set the following item operations.
Schedule
•
Power
•
Source
•
Light Source Mode
•
A/V Mute
•
Light Source Calibration
•
Volume
Set the date, day of the week, and time to execute the event. You can set up to four weeks later. Use the soft keyboard to enter the date and time.
s
"Soft keyboard operations" p.103
Setting an Event Schedule e Select Save , and then press the [ ] button.
To register additional events, repeat steps 3 to 5.
The registered event is displayed on the screen. The event status and time are indicated by icons or indicators.
•
On or Off lets you enable or disable the selected event.
•
Edit lets you change the event details or date and time.
•
Clear lets you remove the scheduled event from a list.
h Select Complete , and then select Yes to finish saving.
To delete all scheduled events, select Schedule Reset .
72
A
: valid schedule
: regular schedule
: invalid schedule
B The date currently selected (highlighted in yellow)
C
: one time schedule
: regular schedule
: standby schedule (turns communication on or off during standby)
: invalid schedule f g
To edit a scheduled event, select the schedule and press ESC .
Select an option from the menu displayed.
Managing Users (Password Protection)
The password prevents anyone from using the projector without first entering a password. It also prevents settings from being changed such as the screen displayed at startup.
This acts as an anti-theft function as the projector cannot be used even if it is stolen, and you can limit who can use the projector.
Kinds of Password Protection
You can set up the following types of password security using one shared password:
•
Power On Protection password prevents anyone from using the projector without first entering a password. When plugging the power cord and turning on the projector at first time, you must enter the correct password. This also applies to Direct Power On and Auto Power
On.
•
User's Logo Protection password prevents anyone from changing the custom screen displayed when the projector turns on, or when no signal is being input. The custom screen discourages theft by identifying the projector's owner.
•
Network Protection password prevents anyone from changing the projector's Network settings.
•
The Schedule Protection password prevents anyone from changing the projector's schedule settings.
Setting a Password
To use password security, you must set a password.
a
The default password is set to "0000". Change this to your own password.
73 a Hold down the [Effect] button on the remote control for about 5 seconds.
The Password Protection setting menu is displayed.
a
If Password Protection is already activated, you must enter the correct password to display the Password Protection setting menu.
b Select Password , and then press the [ ] button.
You see the prompt "Change the password?".
c Select Yes , and then press the [ ] button.
a
If you select No , the Password Protection setting menu is displayed again.
Managing Users (Password Protection) d Press the numeric buttons to set a four digit password.
74
The password displays as " *** "as it is entered. A confirmation prompt is displayed when you enter the fourth digit.
e Enter the password again.
"Password accepted. " is displayed. If you enter the password incorrectly, a message is displayed prompting you to re-enter the password.
f g
Press [Esc] to return to the menu.
Make a note of the password and keep it in a safe place.
Selecting Password Security Types
After setting a password, you see this menu, allowing you to select the password security types you want to use.
If you do not see this menu, hold down the [Effect] button on the remote control for 5 seconds until the menu is displayed.
•
To prevent unauthorized use of the projector, select On as the Power
On Protection setting.
•
To prevent changes to the User's Logo screen or related display settings, select On as the User's Logo Protection setting.
•
To prevent changes to network settings, select On as the Network
Protection setting.
•
To prevent changes to the projector's schedule settings, select On as the
Schedule Protection setting.
You can attach the password protect sticker to the projector as an additional theft deterrent.
a
Make sure you store the remote control in a safe place. If you lose the remote control, you cannot enter the password.
Entering a Password to Use the Projector
When the password screen is displayed, enter the correct password.
Managing Users (Password Protection) a Press the numeric buttons to enter the password.
The password screen closes.
b If the password is incorrect, you see a message and a prompt to try again. Enter the correct password to proceed.
75
Attention
•
If you enter the wrong password three times in succession, the message "The projector's operation will be locked."is displayed for approximately five minutes, and the the projector switches to standby mode. If this happens, disconnect the power plug from the electrical outlet, reinsert it, and turn the projector back on. The projector displays the password entry screen again so that you can enter the correct password.
•
If you have forgotten the password, make a note of the " Request Code : xxxxx" number that appears on the screen, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.
•
If you continue to repeat the above operation and input the wrong password
30 times in succession, the message "The projector's operation will be locked.
Contact Epson as described in your documentation." is displayed and the projector does not accept any more password entries. Contact your local dealer or the nearest address provided in the Epson Projector Contact
List.
s
Epson Projector Contact List
Using the Projector on a Network
Follow the instructions in these sections to set up your projector for use on a network.
Wired Network Projection
You can send images to your projector through a wired network. To do this, connect the projector to your network, and then set up your projector and computer for network projection.
After connecting the projector and making network settings, download
Epson iProjection (Windows/Mac) from the website and then install it.
Download Epson iProjection from the following website.
http://www.epson.com
Epson iProjection software sets up your computer for network projection.
You can also project images from multiple computers connected to the network at the same time. See the "Epson iProjection Operation Guide
(Windows/Mac)" for instructions.
a
Before making settings, connect the LAN cable to the LAN port on the projector.
s
"Connecting to Various Devices" p.24
a b
Press the [Menu] button on the remote control.
Select Network , and then press the [ ] button.
77
LAN
Selecting Wired LAN Settings
Before you can project from computers on your network, you need to select network settings on the projector.
c Select Network Configuration , and then press the [ ].
Wired Network Projection d Select Basic , and then press the [ ] button.
78
•
Projector Keyword : Lets you turn on a security password to prevent access to the projector by anyone not in the room with it.
You must enter a displayed keyword using Epson iProjection to project images and send or receive data.
•
Display Keyword : Lets you display a projector keyword on the projection screen when connecting to the projector using Epson iProjection.
•
Display LAN Info.
lets you set the display format for the projector's network information.
a
Use the displayed keyboard to enter the name, passwords and keyword. Press the [ ][ ][ ][ ] buttons on the remote control to highlight characters, and press [ ] to select them.
f Select Wired LAN , and then press the [ ] button.
e Select the basic options as necessary.
•
Projector Name : Enter the projector name used to identify the projector over a network. You can enter up to 16 single-byte alphanumeric characters.
•
PJLink Password : Lets you set a password for using the PJLink protocol for projector control. You can enter up to 32 single-byte alphanumeric characters.
•
Web Control Password : Allows you to set a password for accessing the projector using Epson iProjection or Epson Web Control. You can enter up to 8 single-byte alphanumeric characters. (The user name is EPSONWEB ; the default password is admin .)
•
Moderator Password : Lets you set an authentication password when connecting to the projector as a moderator using Epson iProjection. Enter four digits for the password. (There is no default password.) g Assign the IP settings for your network as necessary.
•
If your network assigns addresses automatically, select IP Settings to set the DHCP setting to On .
Wired Network Projection
•
If you must set addresses manually, select IP Settings to set the
DHCP setting to Off , and then enter the projector's IP Address ,
Subnet Mask , and Gateway Address as necessary.
•
If you want to connect the projector to the network using IPv6, select IPv6 Settings .
s
a
Press the [ ][ ][ ][ ] buttons on the remote control, and then select the number you want to enter on the soft keyboard displayed. Press the [ ] button to confirm.
h To prevent the IP address from being displayed on the LAN standby screen, set the IP Address Display setting to Off .
i If you have finished making settings, select Complete . Follow the on-screen instructions to save the settings and close the menu.
j Press the [LAN] button on the remote control.
The wired network settings complete when you see the correct IP address on the LAN standby screen.
79
Wireless Network Projection
You can send images to your projector through a wireless network.
80
•
Epson iProjection (Chromebook) allows you to project images from a
Chromebook.
You can download Epson iProjection (Chromebook) for free from the
Chrome Web Store. Any fees incurred when communicating with the
Chrome Web Store are the responsibility of the customer.
You can connect the projector to your wireless network by configuring the connection manually using the projector's Network menus.
Set the projector's time before configuring the Network menu. If the time is not set, the wireless LAN may not be configured correctly.
s
"Setting the Date and Time" p.30
After making settings on the Network menu, download the necessary network software from the Web site and install it.
•
Epson iProjection (Windows/Mac) software allows you to hold interactive meetings by projecting the computer screens of users over a network. See the "Epson iProjection Operation Guide (Windows/Mac)" for instructions.
•
Epson iProjection (iOS/Android) app allows you to project from iOS or
Android mobile devices.
You can download Epson iProjection (iOS/Android) for free from the
App Store or Google Play. Any fees incurred when communicating with the App Store or Google Play are the responsibility of the customer.
Wireless Network Projection
Selecting Wireless Network Settings Manually
Before you can project from your wireless network, you need to select network settings for the projector.
a b
Press the [Menu] button on the remote control.
Select Network , and then press the [ ] button.
c Select On as the Wireless LAN Power setting.
81 d e
Select Network Configuration , and then press the [ ].
Select Basic , and then press the [ ] button.
Wireless Network Projection f Select the basic options as necessary.
•
Projector Name : Enter the projector name used to identify the projector over a network. You can enter up to 16 single-byte alphanumeric characters.
•
PJLink Password : Lets you set a password for using the PJLink protocol for projector control. You can enter up to 32 single-byte alphanumeric characters.
•
Web Control Password : Allows you to set a password for accessing the projector using Epson iProjection or Epson Web Control. You can enter up to 8 single-byte alphanumeric characters. (The user name is EPSONWEB ; the default password is admin .)
•
Moderator Password : Lets you set an authentication password when connecting to the projector as a moderator using Epson iProjection. Enter four digits for the password. (There is no default password.)
•
Projector Keyword : Lets you turn on a security password to prevent access to the projector by anyone not in the room with it.
Set Projector Keyword to On when using thumbnail display or the send function between the projector and connected devices.
•
Display Keyword : Lets you display a projector keyword on the projection screen when connecting to the projector using Epson iProjection.
•
Display LAN Info.
lets you set the display format for the projector's network information.
a
Use the displayed keyboard to enter the name and password.
Press the [ ][ ][ ][ ] buttons on the remote control to highlight characters, and press [ ] to select them.
g Select Wireless LAN , and then press the [ ] button.
82 h Select the Connection Mode setting.
•
Quick lets you connect to multiple smartphones, tablets, or computers directly using wireless communication.
•
Advanced : Lets you connect to a smartphone, tablet, or computer over a wireless LAN access point.
i If you selected the Advanced connection mode, select Search
Access Point to select the access point you want to connect to.
a
If you need to assign the SSID manually, select SSID to enter the SSID.
j For the Advanced connection mode, assign the IP settings for your network as necessary.
•
If your network assigns addresses automatically, select IP Settings to set the DHCP setting to On .
Wireless Network Projection
83
•
If you must set addresses manually, select IP Settings to set the
DHCP setting to Off , and then enter the projector's IP Address ,
Subnet Mask , and Gateway Address as necessary.
•
If you want to connect the projector to the network using IPv6, select IPv6 Settings .
s
k To prevent the SSID or IP address from being displayed on the
LAN standby screen, set the SSID Display setting or the IP
Address Display setting to Off .
l If you have finished making settings, select Complete . Follow the on-screen instructions to save the settings and close the menu.
m Press the [LAN] button on the remote control.
The wired network settings complete when you see the correct IP address on the LAN standby screen.
Selecting Wireless Network Settings in Windows
Before connecting to the projector, select the correct wireless network on your computer.
a To access your wireless utility software, double-click the network icon on the Windows taskbar.
b When connecting in Advanced, select the network name (SSID) of the network the projector is connecting to.
c Click Connect .
Selecting Wireless Network Settings in Mac
Before connecting to the projector, select the correct wireless network on your computer.
a b
Click the Wi-Fi icon on the menu bar at the top of the screen.
When connecting in Advanced connection mode, make sure Wi-Fi is turned on and select the network name (SSID) of the network the projector is connecting to.
When you have finished making wireless settings for your projector, you need to select the wireless network on your computer. Then start the network software to send images to your projector through a wireless network.
Wireless Network Projection
Setting Up Wireless Network Security
You can set up security for your projector to use on a wireless network. Set up one of the following security options to match the settings used on your network:
•
WPA2-PSK security
•
WPA2-EAP security *
•
WPA/WPA2-PSK security *
•
WPA/WPA2-EAP security *
* Only available for Advanced connection mode.
a
Contact your network administrator for guidance on entering the correct information.
a Make sure your digital certificate file is compatible with the projector and stored in the root directory of the SD card.
s
"Supported Client and CA Certificates" p.86
b c d
Press the [Menu] button on the remote control.
Select Network , and then press the [ ] button.
Select Network Configuration , and then press the [ ].
e Select Wireless LAN , and then press the [ ] button.
f Select Security , and then press the [ ] button.
84 g Select the security settings to match your network settings.
Wireless Network Projection
•
WPA2-PSK, WPA/WPA2-PSK:
Select Complete . Follow the on-screen instructions to save the settings and close the menu.
•
WPA2-EAP, WPA/WPA2-EAP:
Select EAP Method , and then press the [ ] button.
h i
Select the protocol for authentication as the EAP Type setting.
Select a certificate type, and then press the [ ] button.
•
Client Certificate for the PEAP-TLS or EAP-TLS type
•
CA certificate for the PEAP , PEAP-TLS , EAP-TLS , or EAP-FAST type a
You can also register the digital certificates from your Web browser. However, be sure to register just once or the certificate may not install correctly.
s
"Setting a certificate using a Web browser" p.89
j k l m
Select Register , and then press the [ ] button.
Insert the SD card into the projector's SD card slot.
Press the [ ] button to display the certificate list.
Select the certificate to import using the displayed list.
A message is displayed prompting you to enter the password for the certificate.
n Enter the password, and then press the [ ] button.
The certificate is imported and a completion message appears.
o Select your EAP settings as necessary.
85
•
User Name : Enter the user name. You can enter up to 64 singlebyte alphanumeric characters. When entering more than 32 characters, use your Web browser to enter the text. When importing a client certificate, the name the certificate was issued to is automatically set.
•
Password : Enter the password used for authentication in PEAP ,
EAP-FAST , and LEAP . You can enter up to 64 single-byte alphanumeric characters. When entering more than 32 characters, use your Web browser to enter the text.
•
Verify Server Cert.
lets you select whether or not to verify the server certificate when a CA certificate has been set.
•
RADIUS Serv.Name
lets you enter the server name to be verified.
p If you have finished making settings, select Complete . Follow the on-screen instructions to save the settings and close the menu.
Wireless Network Projection
86
Supported Client and CA Certificates
You can register these types of digital certificates.
Client Certificate (PEAP-TLS/EAP-TLS)
Format
Item
Extension
Encryption
Hashes
Key length
Password *
Explanation
PKCS#12
PFX, P12
RSA
MD5/SHA-1/SHA-256/SHA-384/SHA-512
512/1024/2048/4096 bit
You need to setup a password. Up to 32 single-byte alphanumeric characters
CA Certificate (PEAP/PEAP-TLS/EAP-TLS/EAP-FAST)
Format
Item
Extension
Encryption
Hashes
Key length
Encoding
Explanation
X509v3
DER/CER/PEM
RSA
MD5/SHA-1/SHA-256/SHA-384/SHA-512
512/1024/2048/4096 bit
BASE64/Binary
* You can set a password using up to 64 alphanumeric characters. When entering more than 32 characters, use your Web browser to enter the text.
s
"Operating Using Epson Web Control (Web Browser)" p.40
Using a QR Code to Connect a Mobile Device
After making the wireless network settings for your projector, you can display a QR code on the screen and use it to connect a mobile device using the Epson iProjection (iOS/Android) app.
a • Make sure you have installed the latest version of Epson iProjection on your device (Epson iProjection V1.3.0 or later supports this feature).
• You can download Epson iProjection for free from the App Store or
Google Play. Any fees incurred when communicating with the App
Store or Google Play are the responsibility of the customer.
• When using Epson iProjection in Quick, we recommend making security settings.
a Select Display the QR Code from the Network menu.
The QR code is displayed on the projected surface.
a • If you do not see the QR code, set the Display LAN Info.
setting to Text & QR Code in the projector's Network menu.
s Network - Network Configuration - Display LAN Info.
• To hide the QR code, press the [Esc] button.
•
When the QR code is hidden, press the [ ] button to display the code.
b c
Start Epson iProjection on your mobile device.
Read the projected QR code using Epson iProjection to connect it to the projector.
Wireless Network Projection a
To correctly read the QR code, make sure you face the screen squarely and closely enough so that the projected code fits into the guide of the mobile device's QR code reader. If you are too far from the screen, the code may not be read.
When a connection is established, select Contents menu from , and then select the file you want to project.
87
Secure HTTP
88
You can use the HTTPS protocol to increase security between the projector and a Web browser communicating with it. To do this, you need to create a server certificate, install it on the projector, and set Secure HTTP to On to verify the reliability of the Web browser.
s Network - Network Configuration - Others - Secure HTTP
Even if you do not install a server certificate, the projector automatically creates a self-signed certificate and allows communication. However, because the self-signed certificate cannot verify reliability from a Web browser, you see a warning about the server's reliability when you access the projector from a Web browser. This warning does not prevent communication.
Importing a Web Server Certificate Using the
Menus
You can create a Web server certificate and import it using the projector menus and an SD card.
a
You can also register the digital certificates from your Web browser.
However, be sure to register just once or the certificate may not install correctly.
s
"Setting a certificate using a Web browser" p.89
a Make sure your digital certificate file is compatible with the projector and stored in the root directory of the SD card.
s
"Supported Web Server Certificates" p.89
b c d
Press the [Menu] button on the remote control.
Select Network , and then press the [ ] button.
Select Network Configuration , and then press the [ ].
Secure HTTP
89 e Select the Others menu, and then press the [ ] button.
f g h i j k
Select On as the Secure HTTP setting.
Select Web Server Cert.
, and then press the [ ] button.
Select Register , and then press the [ ] button.
Insert the SD card into the projector's SD card slot.
Press the [ ] button to display the certificate list.
Select the certificate to import using the displayed list.
A message is displayed prompting you to enter the password for the certificate.
l Enter the password, and then press the [ ] button.
The certificate is imported and a completion message appears.
Supported Web Server Certificates
You can register these types of digital certificates.
Web Server Certificate (Secure HTTP)
Format
Item
Extension
Encryption
Hashes
Key length
Common Name
Organization
Password *
Explanation
PKCS#12
PFX, P12
RSA
SHA-256
2048 bit
Projector Name
SEIKO EPSON CORP.
You need to setup a password. Up to 32 single-byte alphanumeric characters
* You can set a password using up to 64 alphanumeric characters. When entering more than 32 characters, use your Web browser to enter the text.
s
"Operating Using Epson Web Control (Web Browser)" p.40
Setting a certificate using a Web browser
You can use an electronic certificate as the projector's security settings.
a
You can install the electronic certificate from the projector's Network menu. However, be sure to register just once or the certificate may not install correctly.
s
"Setting Up Wireless Network Security" p.84
a Prepare a certificate that is supported by the projector.
Secure HTTP b c
Make sure the projector is turned on.
Launch the Web browser on the computer or mobile device connected to the network.
d Enter the IP address of the projector in the address input box of the browser to connect to the Epson Web Control screen.
The Home screen is displayed.
90 g Click the button to browse a file, and then select the certificate file.
h i
Enter the password in the Password box, and then click Send .
When the settings are complete, click the Apply .
e Select Advanced .
a
You need to login to display the Advanced screen. When the login screen is displayed, enter your user name and password.
(The user name is EPSONWEB; the default password is admin.)
Click the menu icon at the top left to display the menu.
f Select Certificate from Network .
Configuration Menu
This chapter explains how to use the Configuration menu and its functions.
Using the Configuration Menu
This section explains how to use the Configuration menu.
Check the guide under the menu for the available buttons and their operations.
a Display the Configuration menu screen.
c Select a submenu item.
b Select a top menu item.
d Change settings.
92 a
When Default : Reset is displayed on the guide under the menu, pressing the [Default] button on the remote control returns the settings being adjusted to their default values.
Using the Configuration Menu e Press the [Menu] button to finish making settings.
93
List of Functions
Configuration Menu Table
Settable items vary depending on the model being used and the image signal and source being projected.
Top Menu Name
Image menu s
Signal menu s
Settings menu s
Submenu Name
Color Mode
Brightness
Contrast
Color Saturation
Tint
Sharpness
White Balance
Advanced
Dynamic Contrast
Aspect
Advanced
Scale
Keystone
Volume
Brightness Settings
Remote Receiver
User Button
Items or Setting Values
Dynamic, Normal
0 to 100
0 to 100
0 to 100
0 to 100
0 to 20
Color Temp., Custom
Gamma
Off, Normal, and High Speed
Auto, Normal, 4:3, 16:9, Full,
Zoom, Native
HDMI Video Range
Scale, Scale Mode, Scale Vertically,
Scale Horizontally, Clip
Adjustment, Clip Range
H/V-Keystone, Quick Corner
0 to 20
Light Source Mode, Brightness
Level
On, Off
Light Source Mode, Multi-
Projection, Info, Display the QR
Code, Messages, Brightness Level
94
Top Menu Name
Extended menu s s
Network menu
Submenu Name
Test Pattern
Content Playback
Display
User's Logo
Projection
Operation
Standby Mode
Multi-Projection
Schedule Settings
Language
Wireless LAN Power
Net. Info. - Wireless
LAN
Items or Setting Values
Standard, Cross-hatching, Crosshatching R, Cross-hatching G,
Cross-hatching B, Color Bars V,
Color Bars H, Grayscale, Gray Bars
V, Gray Bars H, Checkerboard 1,
Checkerboard 2, White, Black,
Aspect Frame
-
Overlay Effect, SD Viewer
Messages, Startup Screen, Standby
Confirmation, Color Uniformity
Front, Front/Ceiling, Rear, and
Rear/Ceiling
Direct Power On, High Altitude
Mode, Auto Power On, Indicators,
Startup Source, HDMI EQ Setting,
Date & Time
Standby Mode, Port
Multi-Projection, Projector ID,
Color Mode, Color Uniformity,
Edge Blending, Scale, Brightness
Settings, Color Matching, Reset
-
27 languages
On, Off
Connection Mode, Wireless LAN
Sys., Antenna Level, Projector
Name, SSID, DHCP, IP Address,
Subnet Mask, Gateway Address,
MAC Address, Region Code, IPv6
Address (Manual), IPv6 Address
(Auto)
List of Functions
Top Menu Name
Info menu s
Reset Menu s
Submenu Name Items or Setting Values
Net. Info. - Wired LAN Projector Name, DHCP, IP
Address, Subnet Mask, Gateway
Address, MAC Address, IPv6
Address (Manual), IPv6 Address
(Auto)
Display the QR Code
Network Configuration -
-
Projector Info Operation Hours, Source, Input
Signal, Resolution, Refresh Rate,
Sync Info, Status, Serial Number,
Event ID
Light Source Info
Version
Refresh Mode
Light Source Calibra‐ tion
Reset All Config
Light Source Hours
Main
-
Timer, Start
Run Now, Run Periodically,
Schedule Settings
Network menu
Top Menu Name
Basic menu s
Wireless LAN menu s
Submenu Name
Projector Name
PJLink Password
Web Control Password -
-
-
Items or Setting Values
Moderator Password
Projector Keyword
Display Keyword
Display LAN Info.
Connection Mode
-
On, Off
On, Off
Text & QR Code, Text
Quick, Advanced
Top Menu Name Submenu Name
Search Access Point
SSID
Security
Wired LAN menu s
Notifications menu s
Passphrase
EAP Method
Channel
IP Settings
SSID Display
IP Address Display
IPv6 Settings
IP Settings
IP Address Display
IPv6 Settings
Mail Notification
SMTP Server
Port Number
From
-
Items or Setting Values
-
-
Open, WPA2-PSK,
WPA/WPA2-PSK,
WPA2-EAP,
WPA/WPA2-EAP
EAP Type, User Name,
Password, Client
Certificate, Verify Server
Cert., CA certificate,
RADIUS Serv.Name
1ch, 6ch, and 11ch
DHCP, IP Address,
Subnet Mask, Gateway
Address
On, Off
On, Off
IPv6, Auto Configuration,
Use Temporary Address
DHCP, IP Address,
Subnet Mask, Gateway
Address
On, Off
IPv6, Auto Configuration,
Use Temporary Address
-
-
-
On, Off
95
List of Functions
Top Menu Name
Others menu s
Submenu Name
Address 1 Setting,
Address 2 Setting,
Address 3 Setting
SNMP
Trap IP Address 1, Trap IP
Address 2
Community Name
PJLink Notification
Notified IP Address
Secure HTTP
Web Server Certificate
Priority Gateway
Crestron Connected
Art-Net
Message Broadcasting
-
-
Items or Setting Values
Email Address, No Signal,
System Error, Laser Error,
High Temp Error, Laser
Warning, High Temp
Warning
-
On, Off
On, Off
On, Off
-
Wired LAN, Wireless
LAN
On, Off
Art-Net, Net, Sub-Net,
Universe, Start Channel
On, Off
Image Menu
Settable items vary depending on the image signal and source currently being projected. Setting details are saved for each Color Mode.
Submenu
Color Mode
Brightness
Contrast
Function
You can select the quality of the image to suit your surroundings.
s
"Selecting the Projection Quality (Selecting Color
Adjusts the image brightness.
Adjusts the difference between light and shade in the images.
Color Saturation Adjusts the color saturation for the images.
Tint You can adjust the image tint.
Sharpness Adjusts the image sharpness.
96
List of Functions
97
Submenu
White Balance
Advanced
Dynamic Contrast
Reset
*2
Function
You can adjust the overall tint of the image.
Color Temp.
* 1 : You can adjust the overall tint of the image within 14 stages from 3200K to 10000K. The image is tinted blue when a high value is selected and tinted red when a low value is selected. When Color Mode is set to Dynamic , the set Color Temp. may differ from the actual Color Temp.
of the light from the projector. Use this menu as a guide.
Custom : Adjusts the R (red), G (green), and B (blue) components of the offset and gain.
Gamma : You can adjust the coloring by selecting one of the gamma correction values, or referring to the projected graph.
Set to Normal or High Speed to adjust the iris to obtain the optimum light for images being projected. Select High
Speed to make faster iris corrections to match the speed of the scene.
You can reset all adjustment values on the Image menu to their default settings, except for Color Mode . See the following to return all menu items to their default settings.
s
* 1 This cannot be set when Color Filter is set to Warm White or Cool
White .
s Settings - Content Playback - Overlay Effect - Color Filter
* 2 This cannot be set when Multi-Projection is set to On .
Signal Menu
Settable items vary depending on the image signal and source currently being projected. Setting details are saved for each image signal.
Submenu
Aspect
Advanced
Scale
Reset
Function
You can set the Aspect Ratio g
for projected images.
s
"Changing the Aspect Ratio of the Projected Image" p.54
HDMI Video Range : Select the video range for the input signal from the HDMI port. Set to Expanded if you are concerned about misadjusted black levels or blown out highlights in the image.
When using multiple projectors to project one image, adjust the range of the image displayed by each projector.
s
"Displaying a Scaled Image" p.64
You can reset all adjustment values for the Signal menu to their default settings.
See the following to return all menu items to their default settings.
s
List of Functions
Settings Menu
Submenu
Keystone
Volume *1
Function
You can correct distortion.
s
"Correcting Distortion in the Projected Image" p.49
•
H/V-Keystone :
Adjust V-Keystone and H-Keystone to correct vertical and horizontal keystone distortion.
•
Quick Corner :
Select and correct the four corners of the projected image.
You can adjust the volume. Setting values are saved for each source.
98
Submenu
Brightness Settings
Remote Receiver
User Button
Test Pattern
Function
Light Source Mode : (Only available when Multi-Projection is set to Off ) Sets the brightness for the light source.
•
Normal : Select this if you do not want to decrease the brightness. This makes the target usage time approximately 20,000 hours.
•
Quiet : Select this if you are concerned about the noise made by the fan, This sets the brightness at 50%. This makes the target usage time 20,000 hours.
•
Extended : Select this to extend the life expectancy of the light source. This sets the brightness at 50%. This makes the target usage time approximately 30,000 hours.
•
Custom : Select this to set the brightness level within a range of 50 to 100%.
Brightness Level : (Only available when Light Source Mode is set to Custom ) Sets the brightness for the light source.
s
You can limit the reception of the operation signal from the remote control.
When set to Off , you cannot perform any operations from the remote control. If you want to make operations from the remote control, hold down the [Menu] button on the remote control for at least 15 seconds to reset the setting to its default value.
Select the item from the Configuration menu that you want to assign to the [User] button on the remote control. You can assign the following items.
Light Source Mode , Multi-Projection , Info , Display the
QR Code , Messages , Brightness Level
You can display a test pattern to adjust the projection without connecting other equipment when you set up the projector.
s
"Displaying a Test Pattern" p.48
List of Functions
99
Submenu
Content Playback
Reset
Function
Overlay Effect * 2 : Set the filter you want to apply to the image.
s
SD Viewer : Allows you to select the playlist you want to play from the SD card.
s
You can reset all adjustment values on the Settings menu to their default settings, except for User Button .
See the following to return all menu items to their default settings.
s
* 1 This cannot be set when the source is set to Spotlight.
* 2 This cannot be set in the following situations.
- When Edge Blending is set to On .
- When the source is an SD player and a non-writable error has occurred.
- When the source is an SD player and the playlist cannot be played.
Extended Menu
Submenu
Display
User's Logo *
Function
You can make settings related to the projector's display.
Messages : When set to Off , the following items will not be displayed.
Item names when the Source, Color Mode, or Aspect is changed, messages when no signal is being input, and warnings such as High Temp Warning.
Startup Screen * : Set to On to display the User's Logo when you turn on the projector.
Standby Confirmation : If it is set to Off , you can turn off the power simply by pressing the [ t ] button once.
Color Uniformity : Adjusts the color tone balance for the whole screen.
s
"Adjusting uneven colors (Color Uniformity)" p.65
You can change the user's logo that is displayed as a background during Display Background, A/V Mute, and so on.
s
List of Functions
Submenu
Projection
Operation
Function
Select from one of the following projection methods depending on how the projector is installed.
Front , Front/Ceiling , Rear , and Rear/Ceiling
You can change the direction of the image as follows by pressing down the [A/V Mute] button for about five seconds.
Front W Front/Ceiling
Rear W Rear/Ceiling
Direct Power On : Set to On to turn on the projector simply by plugging it in to an outlet.
When the power cord is plugged in, note that the projector turns on automatically in cases such as a power outage being restored.
High Altitude Mode : Set to On when using the projector above an altitude of 1,500 m.
Auto Power On : If this is set to HDMI , the projector turns on when a signal is received from the HDMI port, even when the projector is in standby status.
Indicators : When set to Off , the projector's indicators are turned off. When set to Off , they turn on when an error or a warning occur, or when standing by or warming up.
Startup Source : Set the source you want to input when the projector starts up.
HDMI EQ Setting : Change the HDMI reception level according to the video source connected to the HDMI input port. Change this setting if there is noise in the image or if the image is not displayed. If a stick type device is not connected, change the setting to 1 .
Date & Time : Make system time settings for the projector.
s
"Setting the Date and Time" p.30
100
Submenu Function
Standby Mode Standby Mode : If you set this to Communication On , you can perform network monitoring and control the projector even if the projector is in standby mode.
a
When monitoring or controlling the pro‐ jector using wireless LAN, set Connection
Mode to Advanced .
s Network - Wireless LAN - Connection
Mode
Port : Select the communication port that is enabled when
Standby Mode is set to Communication On .
List of Functions
101
Submenu
Schedule Settings
Language
Function
Multi-Projection Make settings when projecting from multiple projectors.
s
"Projecting One Image from Multiple Projectors (Multi-
Multi-Projection : Set this to On when adjusting multiple images side-by-side.
Projector ID : Set the ID from 1 to 9.
Off indicates that no
ID is set.
s
"Setting the Projector ID" p.61
Color Mode : You can select the quality of the image to suit your surroundings.
s
"Selecting the Projection Quality (Selecting Color
Color Uniformity : Adjusts the color tone balance for the whole screen.
s
"Adjusting uneven colors (Color Uniformity)" p.65
Edge Blending : Corrects a border between multiple images to create a seamless screen.
s
"Adjusting the Points Where the Images Overlap (Edge
Scale : When using multiple projectors to project one image, adjust the range of the image displayed by each projector.
s
"Displaying a Scaled Image" p.64
Brightness Settings : Sets the brightness mode of the projector.
s
"Adjusting the Brightness of the Overlay Effect" p.47
Color Matching : Corrects the difference between the tint and brightness of each projected image.
s
"Adjusting the tint (Color Matching)" p.67
Reset : You can reset all adjustment values for the Multi-
Projection menu to their default settings.
You can set the projector's schedule so that it performs a specific operation at a pre-scheduled time.
s
"Setting an Event Schedule" p.71
You can set the language for messages and menus.
Submenu
Reset
Function
You can reset all adjustment values for the Extended menu to their default settings. However, the following items are not reset.
Color Uniformity , Projection , High Altitude Mode , HDMI
EQ Setting , Standby Mode , Port , Multi-Projection ,
Projector ID , Color Mode , Color Matching , Language
See the following to return all menu items to their default settings.
s
* When User's Logo Protection is set to On in Password Protection , you cannot change settings related to user's logo. You can make changes after setting User's Logo Protection to Off .
s
"Kinds of Password Protection" p.73
List of Functions
Network Menu
When Network Protection is set to On in Password Protection , a message is displayed and the network settings cannot be changed. Set Network
Protection to Off and then configure the network.
s
"Managing Users (Password Protection)" p.73
Submenu
Wireless LAN
Power
Function
Set this to On when connecting the projector and a computer over a wireless LAN. If you do not want to connect over wireless
LAN, turn it Off to prevent unauthorized access and so on by others.
102
Submenu
Net. Info. - Wireless LAN
Net. Info. - Wired
LAN
Display the QR
Code
Function
Displays the following network setting status information.
•
Connection Mode
•
Wireless LAN Sys.
•
Antenna Level
•
Projector Name
•
SSID
•
DHCP
•
IP Address
•
Subnet Mask
•
Gateway Address
•
MAC Address
•
Region Code
When IPv6 is selected, the following information is displayed.
•
IPv6 Address (Manual):
IPv6 Address, Prefix Length, Gateway Address
•
IPv6 Address (Auto):
Temporary Address, Link-local Address, Stateless Address,
Stateful Address
Displays the following network setting status information.
•
Projector Name
• DHCP
•
IP Address
• Subnet Mask
•
Gateway Address
•
MAC Address
•
IPv6 Address (Manual):
IPv6 Address, Prefix Length, Gateway Address
•
IPv6 Address (Auto):
Temporary Address, Link-local Address, Stateless Address,
Stateful Address
When connecting iOS or Android devices using Epson iProjection, read the QR code displayed.
List of Functions
103
Submenu
Network Configuration
Function
The following menus are available for setting Network items.
Basic , Wireless LAN , Wired LAN , Notifications , Others , Reset
Notes on operating the Network menu
Selecting from the top menu and sub menus, and changing selected items is the same as making operations from the Configuration menu.
When done, make sure you go to the Complete menu, and select Yes , No , or Cancel . When you select Yes or No , you are returned to the
Configuration menu.
•
Each time the CAPS key is selected and the [ ] button is pressed, it sets and changes between upper case and lower case letters.
•
Each time the SYM1/2 key is selected and the [ ] button is pressed, it sets and changes the symbol keys for the section enclosed by the frame.
The following types of character can be entered.
Numbers
Letters
Symbols
0123456789
ABCDEFGHIJKLMNOPQRSTUVWXYZ abcdefghijklmnopqrstuvwxyz
! " # $ % & ' ( ) * + , - . / : ; < = > ? @ [ \ ] ^ _ ` { | } ~
Yes : Saves the settings and exits the Network menu.
No : Does not save the settings and exits the Network menu.
Cancel : Continues displaying the Network menu.
Soft keyboard operations
The Network menu contains items that require input of alphanumerics during setup. In this case, the following software keyboard is displayed. Use the [ ][ ][ ][ ] buttons to move the cursor to the desired key, and then press the [ ] button to enter the selected character. After inputting, press Finish on the keyboard to confirm your input. Press Cancel on the keyboard to cancel your input.
List of Functions
Basic menu
Submenu Function
Projector Name Enter the projector name used to identify the projector over a network.
When editing, you can enter up to 16 single-byte alphanumeric characters. (" * + , / : ; < = > ? [ \ ] ` | and spaces cannot be used.)
PJLink Password Set a password to use when you access the projector using compatible PJLink software.
You can enter up to 32 single-byte alphanumeric characters.
(Spaces and symbols cannot be used.) s
Web Control
Password
Set a password for authentication to use when making settings and controlling the projector using Epson iProjection or Epson
Web Control. You can enter up to eight single-byte alphanumeric characters ( * : and spaces cannot be used). The default user name is "EPSONWEB" and the default password is
"admin".
s
"Operating the Projector Using a Mobile Device or
104
Submenu
Moderator Password
Function
Enter the four digit authentication password for using Epson iProjection when connecting to the projector as a moderator.
(There is no default password.)
Projector Keyword
Set this to On to enable a security password to prevent other users from accidentally projecting images. When projecting images from a computer or mobile device, you need to enter the keyword displayed on the projection screen in Epson iProjection.
Display Keyword When this is set to On and when connecting to the projector using Epson iProjection, the projector keyword is displayed on the projection screen. Only available when Projector Keyword is set to On .
Display LAN Info.
Set the display format for the projector's network information. If you display the QR code, you can connect to a network just by reading the QR code in Epson iProjection. Text & QR Code is set by default.
List of Functions
Wireless LAN menu
Submenu
Connection
Mode
Search Access
Point
SSID
Function
Set the connection mode to use when connecting the projector and a computer via a wireless LAN.
Quick : Lets you directly connect to a smartphone, tablet, or computer via a wireless LAN.
Advanced : Lets you connect to a smartphone, tablet, or computer over a wireless LAN access point. The connection is established in infrastructure mode.
When Connection Mode is set to Advanced , you can search for surrounding access points, and set the SSID to be connected from those access points. Depending on the access point settings, they may not be displayed in the list.
s
"Search Access Point screen" p.107
Enter an SSID. When an SSID is provided for the wireless
LAN system in which the projector participates, enter the
SSID.
You can enter up to 32 single-byte alphanumeric characters.
105
Submenu
Security
Passphrase
Function
Select the security type according to the wireless LAN settings.
Off : Security is not set.
WPA2-PSK : Communication is performed using WPA2 security. Uses AES method for encryption. When establishing a connection from a computer to the projector, enter the value set in the passphrase.
WPA/WPA2-PSK * : Connects in WPA personal mode.
Encryption method is selected automatically according to the access point settings. Set a passphrase which is the same for the access point.
WPA2-EAP * : Communication is performed using WPA2 security. Uses AES method for encryption.
WPA/WPA2-EAP * : Connects in WPA enterprise mode.
Encryption method is selected automatically according to the access point settings.
Enter a passphrase used to connect to the network when
Security is set to WPA2-PSK or WPA/WPA2-PSK .
You can enter at least 8 and up to 63 single-byte alphanumeric characters.
You can enter up to 32 characters on the Configuration menu. When entering more than 32 characters, use your
Web browser to enter the text.
s
"Operating Using Epson Web Control (Web Browser)" p.40
When Connection Mode is set to Quick , the initial passphrase is set.
List of Functions
Submenu
EAP Method
Function
Set protocols for WPA2-EAP and WPA/WPA2-EAP authentication.
EAP Type : Select the certification protocol.
•
PEAP : Authentication protocol widely used in Windows
Server.
•
PEAP-TLS : Authentication protocol used in Windows
Server. Select when using a client certificate.
•
EAP-TLS : Authentication protocol widely used to use a client certificate.
•
EAP-FAST , LEAP : Select this when these authentication protocols are used.
User Name : Enter a user name to be used for authentication. You can enter up to 64 single-byte alphanumeric characters.
You can enter up to 32 characters on the Configuration menu. When entering more than 32 characters, use your
Web browser to enter the text.
s
"Operating Using Epson Web Control (Web Browser)" p.40
If you also need to enter a domain name, add the domain name before the user name separated by a backslash
(domain name\user name).
Password : Enter the password used for authentication in
PEAP, EAP-FAST, and LEAP. You can enter up to 64 single-byte alphanumeric characters. You can enter up to 32 characters on the Configuration menu. When entering more than 32 characters, use your Web browser to enter the text.
s
"Operating Using Epson Web Control (Web Browser)" p.40
When the password is entered and Finish is selected, the value is set and displayed as an asterisk ( * ).
Client Certificate : Imports client certificates for use in
PEAP-TLS and EAP-TLS.
106
Submenu
Channel
IP Settings *
SSID Display
IP Address Display
Function
Verify Server Cert.
: Set to On to perform verification for the certificate of the certification server. To verify a server certificate, you need to set CA certificate.
CA certificate : Imports CA certificates for use in PEAP,
PEAP-TLS, EAP-TLS, and EAP-FAST.
RADIUS Serv.Name
: Specify the name of the certification server. You can enter up to 32 single-byte alphanumeric characters.
You can select the channels used to connect in Quick mode.
If interference from other signals occurs, use a different channel.
Perform network settings.
DHCP : Set to On
to configure the network using DHCP g
.
If this is set to On , you cannot set any more addresses.
IP Address
: You can enter the IP Address g
assigned to the projector. You can enter a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
Subnet Mask : You can enter the Subnet Mask
for the projector. You can enter a number from 0 to 255 in each field of the address. However, the following subnet masks cannot be used.
0.0.0.0, 255.255.255.255
Gateway Address : You can enter the IP address for the gateway for the projector. You can enter a number from 0 to 255 in each field of the address. However, the following
cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
To prevent the SSID from being displayed on the LAN
Standby screen, set this to Off .
To prevent the IP address from being displayed on the LAN
Standby screen, set this to Off .
List of Functions
107
Submenu
IPv6 Settings
Function
Perform settings to use the IPv6 protocols.
a • The following functions support IPv6 protocols.
- Epson Web Control
- PJLink
• When setting the IPv6 address manually, make settings in Advanced from Epson
Web Control.
s
"Operating the Projector Using a
Mobile Device or Computer" p.40
IPv6 : Set this to On when using IPv6 protocols. Make sure one link local address is set when using IPv6. This is composed of the interface ID created from fe80:: and the projector's MAC address.
Auto Configuration : Set this to On to automatically acquire an IPv6 address from RA (Router Advertisement). The address is composed as shown below.
• Stateless Address (0 to 6): Created automatically by combining the prefix acquired from the RA (Router
Advertisement) and the interface ID created from the projector's MAC address.
• Stateful Address (0 to 1): Created automatically from the
DHCP server using DHCPv6.
Use Temporary Address : Set this to On to temporarily validate the IPv6 address (0 to 1) when Auto Configuration is On .
* This can be selected only when Connection Mode is set to Advanced .
Type of security
We recommend making security settings when using the projector in
Advanced mode.
WPA is an encryption standard that improves the security for wireless networks. The projector supports TKIP and AES encryption methods.
WPA also includes user authentication functions. WPA authentication provides two methods: using an authentication server, or authenticating between a computer and an access point without using a server. This projector supports the latter method, without a server.
a
For setting details, follow the instructions from your network administrator.
Search Access Point screen
Detected access points are displayed in a list.
Submenu
Refresh
Function
Searches for the access point again.
Indicates an already set access point.
List of Functions
Submenu Function
Indicates the access points where security is set.
If you select an access point where security has not been set, the
Wireless LAN menu is displayed.
If you select an access point where security has been set, the
Security menu is displayed. Select a type of security according to the security settings for the access point.
Wired LAN menu
108
Submenu
IP Settings
Function
You can make settings related to the following addresses.
DHCP : Set to On
to configure the network using DHCP g
. If this is set to On , you cannot set any more addresses.
IP Address : You can enter the IP Address
projector. You can enter a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
Subnet Mask : You can enter the Subnet Mask
You can enter a number from 0 to 255 in each field of the address.
However, the following subnet masks cannot be used.
0.0.0.0, 255.255.255.255
Gateway Address : You can enter the IP address for the gateway for the projector. You can enter a number from 0 to 255 in each field of the address. However, the following Gateway Address
cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
List of Functions
109
Submenu
IP Address Display
IPv6 Settings
Function
To prevent the IP address from being displayed on the LAN
Standby screen, set this to Off .
Perform settings to use the IPv6 protocols.
a • The following functions support IPv6 proto‐ cols.
- Epson Web Control
- PJLink
• When setting the IPv6 address manually, make settings in Advanced from Epson Web
Control.
s
"Operating the Projector Using a Mobile
IPv6 : Set this to On when using IPv6 protocols. Make sure one link local address is set when using IPv6. This is composed of the interface ID created from fe80:: and the projector's MAC address.
Auto Configuration : Set this to On to automatically acquire an
IPv6 address from RA (Router Advertisement). The address is composed as shown below.
• Stateless Address (0 to 6): Created automatically by combining the prefix acquired from the RA (Router Advertisement) and the interface ID created from the projector's MAC address.
• Stateful Address (0 to 1): Created automatically from the
DHCP server using DHCPv6.
Use Temporary Address : Set this to On to temporarily validate the IPv6 address (0 to 1) when Auto Configuration is On .
Notifications Menu
When this is set, you receive an email notification if a problem or warning occurs in the projector.
s
"Reading error notification mail" p.142
Submenu Function
Mail Notification Set to On to send an email to the preset addresses when a problem or warning occurs with a projector.
SMTP Server You can input the IP Address
for the SMTP server for the projector.
You can enter a number from 0 to 255 in each field of the address.
However, the following IP addresses cannot be used.
127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from
0 to 255)
Port Number
From
You can input the port number for the SMTP server. The default value is 25. You can input numbers between 1 to 65535.
Enter the email address of the sender. You can enter up to 64 single-byte alphanumeric characters. You can enter up to 32 characters on the Configuration menu. When entering more than 32 characters, use your Web browser to enter the text.
( " ( ) , : ; < > [ \ ] and spaces cannot be used.) s
"Operating Using Epson Web Control (Web Browser)" p.40
List of Functions
110
Submenu
Address 1 Setting/Address 2
Setting/Address
3 Setting
SNMP
Trap IP Address
1/Trap IP Address 2
Community
Name
Function
Set the destination email addresses for the notification email, and the notification content. You can register up to three destinations. You can enter up to 64 single-byte alphanumeric characters. You can enter up to 32 characters on the
Configuration menu. When entering more than 32 characters, use your Web browser to enter the text. ( " ( ) , : ; < > [ \ ] and spaces cannot be used.) s
"Operating Using Epson Web Control (Web Browser)" p.40
Set to On to monitor the projector using SNMP
. To monitor the projector, you need to install the SNMP manager program on your computer.SNMP should be managed by a network administrator. The default value is Off .
You can register up to two IP addresses for the SNMP trap notification destination.
You can enter a number from 0 to 255 in each field of the address.
However, the following IP addresses cannot be used.
127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from
0 to 255)
Set the SNMP community name. You can enter up to 32 singlebyte alphanumeric characters. (Spaces and symbols cannot be used.)
Set this to On to use the PJLink notification function.
PJLink Notification
Notified IP Address
Enter the IP address of the computer to which you want to send notifications of the projector's operating status using the PJLink notification function.
You can enter a number from 0 to 255 in each field of the address.
However, the following IP addresses cannot be used.
127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from
0 to 255)
Others menu
Submenu Function
Secure HTTP To strengthen security, communication between the projector and computer in Epson Web Control is encrypted. When setting security with Epson Web Control, we recommend setting this to
On .
Web Server Cert.
Imports the Web server certificate used in Secure HTTP.
Priority Gateway For the priority gateway, select either Wired or Wireless .
Crestron Connected
Set this to On only when monitoring or controlling the projector over the network using Crestron Connected ® . Otherwise, set this to Off .
s
"About Crestron Connected ® " p.144
Changes in projector settings take effect upon restarting.
When this is set to On , the following functions are not available.
• The Message Broadcasting feature in the Epson Projector
Management software
List of Functions
Submenu
Art-Net
Message Broadcasting
Function
Art-Net : Set this to On to control the projector using Art-Net.
s
Net / Sub-Net / Universe : Sets the projector's Net/Sub-Net/
Universe.
Start Channel : Sets the start channel that handles Art-Net.
s
Set this to On to receive information sent by the Message
Broadcasting feature in the Epson Projector Management software.
Download software and User's Guides from the following Web site.
http://www.epson.com
Reset menu
Resets all of the network settings.
Submenu
Reset network settings.
Function
To reset all of the Network settings, select Yes .
111
List of Functions
112
Info Menu (Display Only)
Lets you check the status of the image signals being projected and the status of the projector. Items that can be displayed vary depending on the source currently being projected.
Submenu
Projector Info Operation
Hours *
Source
Input Signal
Resolution
Refresh Rate
Function
Displays the operation time after turning on the projector.
You can display the source name for the connected equipment currently being projected.
You can display the content of Input
Signal set in the Signal menu according to the source.
You can display the resolution.
You can display the Refresh Rate
Light Source
Info
Version
Submenu
Sync Info
Function
You can display the image signal information.
This information may be needed if service is required.
Status
Serial Number Displays the projector's serial number.
Event ID When problems occur when the projector and computer are connected through the network, information on the problem is displayed using an Event ID. See the following page for information on interpreting the Event ID.
s
Light Source
Hours
Main
This is information about errors that have occurred on the projector.
This information may be needed if service is required.
Displays the operating time for the light source according to the Light Source
Mode.
Displays the projector's firmware version information.
* The cumulative use time is displayed as "0H" for the first 10 hours. 10 hours and above is displayed as "10H", "11H", and so on.
List of Functions
Reset Menu
Submenu
Refresh Mode
Light Source Calibration
Function s
Make settings related to Light Source Calibration.
• Run Now : Starts Light Source Calibration.
You cannot use Run Now in the following situations.
- Within 20 minutes of turning off the projector.
- When the temperature of the local environment is high and the brightness of the light source is automatically reduced.
• Run Periodically : When this is set to On , Light Source
Calibration is performed every 100 hours of use.
•
Schedule Settings : Displays the schedule settings screen. Set
Light Source Calibration to run periodically.
113
Submenu Function
Reset All Config You can reset all items in the Configuration menu to their default settings.
The following items are not reset to their defaults: User's Logo , all items on the Network menu, , Language , Date & Time , Color
Uniformity , Color Matching , Light Source Info , and
Operation Hours .
Batch Setup
114
Once the Configuration menu content has been set for one projector, you can use it to perform batch setup for multiple projectors (batch setup function). The batch setup function is only for projectors with the same model number.
Use one of the following methods.
•
Make settings using an SD card.
•
Setup using EasyMP Network Updater.
This guide explains how to use the SD card.
a • The following content is not reflected by the batch setup function.
- The Network menu settings (except for the Notifications menu and the Others menu)
- Status and Light Source Info in the Info menu
• Perform batch setup before adjusting the projected image.
Adjustment values for the projected image, such as Keystone are reflected by the batch setup function. If batch setup is performed after adjusting the projected image, the adjustments you made may change.
• By using the batch setup function, the registered User's Logo is set for the other projectors. Do not register confidential information and so on as the User's Logo.
Making Settings Using an SD Card
This section explains how to perform batch setup using an SD card.
Saving settings to an SD card a Disconnect the power cord from the projector, and check that all of the projector's indicators have turned off.
b Insert an SD card into the projector.
Caution
Performing batch setup is the customers responsibility. If batch setup fails due to a power failure, communication error, and so on, the customer is responsible for any repair costs incurred.
a •
Connect an empty SD card. If the SD card contains data other than the batch setup file, the settings may not be saved correctly.
•
If you have saved a batch setup file from another projector to the SD card, delete the file or change the file name. The batch setup function cannot overwrite a batch setup file.
•
The file name for the batch setup file is PJCONFDATA.bin. If you need to change the file name, add text after
PJCONFDATA. If you change the file name in any other way, the projector may not be able to recognize the file correctly.
•
You can only use single-byte characters for the file name.
Batch Setup c While holding down the [Esc] on the remote control or the control panel, connect the power cord to the projector.
When writing completes normally, the projector enters standby status.
115
When the projector's indicators turn on as follows, release the [Esc] button.
On/Standby
Blue - On
When the projector is in standby status, remove the SD card.
On/Standby
Blue - On
Status
Blue - On
Laser
Orange - On
Temp
Orange - On
When all of the indicators start flashing, the settings are being written to the batch setup file.
Caution
•
Do not disconnect the power cord from the projector while the file is being written. If the power cord is disconnected, the projector may not start correctly.
•
Do not disconnect the SD card from the projector while the file is being written. If the SD card is disconnected, the projector may not start correctly.
Batch Setup
Reflecting saved settings to other projectors a Disconnect the power cord from the projector, and check that all of the projector's indicators have turned off.
b Insert the SD card on which the settings have been saved into the projector.
116 c While holding down the [Menu] on the remote control or the control panel, connect the power cord to the projector.
When the projector's indicators turn on as follows, release the [Menu] button.
a • When the SD card contains 1 to 3 types of batch setup files, the file is reflected to the projector with the same model number. If there are multiple files for a projector with the same model number, the settings may not be reflected correctly.
• When there are four or more types of batch setup files on the
SD card, the settings may not be reflected correctly.
• Do not store any data except for the batch setup file on the
SD card. If the SD card contains data other than the batch setup file, the settings may not be reflected correctly.
On/Standby
Blue - On
Status
Blue - On
Laser Temp
Orange - On Orange - On
The indicators remain on for about 75 seconds.
When all of the indicators start flashing, the settings are being written.
Caution
•
Do not disconnect the power cord from the projector while the settings are being written. If the power cord is disconnected, the projector may not start correctly.
•
Do not disconnect the SD card from the projector while the settings are being written. If the SD card is disconnected, the projector may not start correctly.
Batch Setup
117 d When writing completes normally, the projector enters standby status.
When Setup Fails
The indicators notify you if an error occurs. Check the status of the projector's indicators and follow the instructions described in the table here.
Indicator status Remedy
The batch setup file may be corrupt, or the SD card may not be connected correctly. Disconnect the SD card, unplug and then plug in the projector's power cord, and then try again.
On/Standby
Blue - On
When the projector is in standby status, remove the SD card.
Temp: Orange - flashing fast
Laser: Orange - flashing fast
Writing the settings may have failed and an error may have occurred in the projector's firmware.
Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson
Projector Contact List.
s
Epson Projector Contact List
Temp: Orange - flashing fast
Laser: Orange - flashing fast
Status: Blue - flashing fast
On/Standby: Blue - flashing fast
Troubleshooting
This chapter explains how to identify problems and what to do if a problem is found.
Reading the Indicators
119
This projector has the following five indicators to indicate the projector's status.
A On/Standby indicators
Indicates the projector's status.
B Status indicator
Indicates the projector's status.
C Laser indicator
Indicates the light source status.
D Temp indicator
Indicates the internal temperature status. This is normally turned off.
E WLAN indicator
Indicates the wireless LAN status.
The following indicator status are used during regular operation.
"Status varies" indicates that the indicators turn on, off, or flash depending on the status of the projector.
On/Standby Status
Indicator
Laser Temp
Projector's Status
Blue - On Off
Blue - On Blue - Flashing
Off
Off
Off
Off
Standby condition
Network monitoring status
Warm-up status
Projecting
Explanation
Power is being supplied to the projector. In this status, you can start projecting by pressing the [ t ] button on the remote control or on the projector.
(Sometimes, when the power cord is unplugged, the On/Standby indicator remains lit for a short period, but this is not a fault.)
The projector is being monitored and controlled over a network (when Standby Mode is set to Communication On ).
If the power cord is disconnected and then reconnected in this status, the On/Standby indicator flashes blue.
This is the status immediately after turning on the projector. Warm-up takes approximately 30 seconds after the light source turns on.
The [ t ] button is disabled during warm-up.
The projector is projecting.
Blue - On Blue - On Status varies Off
Reading the Indicators
120
On/Standby
Blue - On
Blue - Flashing
Blue - On
Status
Off
Indicator
Blue - Flashing
Blue - On
Laser
Off
Off
Off
Temp
Off
Off
Projector's Status
Cool down status
Preparing Network monitoring
A/V Mute activated
Explanation
This is the status immediately after turning off the power. In this status, all buttons are disabled.
Preparing to monitor and control this projector over a network.
During network monitoring preparation, all button operations are disabled.
A/V Mute is active.
Off
Refresh Mode activated Refresh Mode is active.
Status varies
Blue - Flashing Orange -
Flashing Status varies
Reading the Indicators
121
When an error has occurred in the projector, the error status is indicated by the indicator's color and combination of flashing or lit.
Refer to the following table to see what the indicators mean and how to remedy problems that they indicate.
On/Standby Status
Indicator
Laser Temp
Cause Remedy or Status
Off Blue - Flashing Orange -
Flashing
Off
Internal Error Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s
Epson Projector Contact List
Off Blue - Flashing Off Orange -
Flashing
Fan Error
Sensor Error
Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s
Epson Projector Contact List
Off
Off
Blue - Flashing Off
Blue - Flashing Orange - On
Orange - On
Off
High Temp Error
(Overheating)
Laser Error
Retardation Plate Error
The light source turns off automatically and projection stops. Wait for about five minutes. The projector enters standby status after approximately five minutes.
Check the following three points.
•
Check that the Air intake vent, Air exhaust vent and the slit in the side of the projector are clear, and that the projector is not positioned against a wall.
•
If dust adheres to the Air intake vent, Air exhaust vent, or the slit in the side of the projector, turn off the projector, unplug the power plug from the outlet, and then clean.
s
"Cleaning the Projector's Surface" p.138
s
"Cleaning the Air Intake Vent and the Air Exhaust Vent" p.138
•
Check if the air intake temperature is too high.
If the error continues, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
Epson Projector Contact List.
s
Epson Projector Contact List
When using at an altitude of 1500 m or more, set High Altitude Mode to On .
s Extended - Operation - High Altitude Mode
Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s
Epson Projector Contact List
Reading the Indicators
122
On/Standby Status
Indicator
Laser Temp
Blue - Flashing Status varies Status varies Orange -
Flashing
Cause
High Temp Warning
Remedy or Status
Laser Warning
Blue - Flashing Status varies Orange -
Flashing
Wireless LAN status
WLAN indicator status
Status varies
Problem and solutions
Wireless LAN is available.
Blue - On
Connecting to device.
Flashing blue quickly
An error has occurred. Turn the projector off and then on again.
This is not an error. However, if the temperature rises too high again, projection stops automatically. Check the following two points.
•
Check that the Air intake vent, Air exhaust vent and the slit in the side of the projector are clear, and that the projector is not positioned against a wall.
•
If dust adheres to the Air intake vent, Air exhaust vent, or the slit in the side of the projector, turn off the projector, unplug the power plug from the outlet, and then clean.
s
"Cleaning the Projector's Surface" p.138
s
"Cleaning the Air Intake Vent and the Air Exhaust Vent" p.138
• Check if the air intake temperature is too high.
Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s
Epson Projector Contact List
Flashing blue slowly
Reading the Indicators
123
WLAN indicator status Problem and solutions
Wireless LAN is un-available. Make sure the wireless LAN settings are correct.
Off a • See the following if the projector is not operating properly, even though the indicators are all showing normal.
s
• If the indicators are in a state not shown in this table, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s
Epson Projector Contact List
Problem Solving
If any of the following problems occur and the indicators do not offer a solution, refer to the pages given for each problem.
Problems Relating to Images
• No images appear
Projection does not start, the projection area is completely black, or the projection area is completely blue.
• Moving images are not displayed
Videos played back are black or no image is projected, or the video is not played back on the computer.
• The playlist does not play.
•
The message "Not supported" is displayed
•
The message "No Signal" is displayed
•
Images are fuzzy, out of focus, or distorted
•
Interference or distortion appear in images
•
The image is truncated (large) or small, the aspect ratio is not suitable, or the image has been reversed
Only part of the image is displayed, the height and width ratios of the image are not correct, or the image may appear reversed from top to bottom or left to right.
•
Image colors are not right
The whole image appears purplish or greenish, images are black
& white, or colors appear dull.
•
Images appear dark
•
Burning appears on the LCD panel.
s
s
s s s s s s
s
s s
Problems when Projection Starts
•
The projector does not turn on s
Solving Network Problems
• Solutions When Wireless Authentication Fails s
•
Solutions When You Cannot Access the Projector using a Web browser
•
Cannot operate the SD card using a Web browser (save/delete playlist, upload data).
•
Email is not received even if a problem occurs in the projector
•
Solutions When the Image Contains Static During Network
Projection s s
s
s
Other Problems
•
No sound can be heard or the sound is faint
•
The remote control does not work
•
I want to change the language for messages and menus
•
Solutions to Password Problems
•
"The battery that saves your clock settings is running low." is displayed
•
Detailed logs and error message are not displayed
•
Cannot control Art-Net correctly.
s
s
s
s
s
s
s
124
Problem Solving
125
Problems Relating to Images
No images appear
Check
Did you press the [ t ] button on the remote control or the projector? Press the [ t ] button to turn on the power.
Are the indicators switched off?
Remedy
The power cord is not connected correctly or power is not being supplied.
Connect the projector's power cord correctly.
Check that your electrical outlet or power source is functioning correctly.
Is A/V Mute active?
Are the Configuration menu settings correct?
Press the [A/V Mute] button to release A/V Mute.
s
"Hiding the Image and Sound Temporarily (A/V Mute)" p.58
Reset all of the settings.
s Reset - Reset All Config
Some input images, such as screen savers, may be completely black.
Is the image to be projected completely black?
(Only when projecting computer images)
Is Windows Media Center displayed in full screen?
(Only during network connection)
Is an application using the Windows DirectX function displayed?
(Only during network connection)
When Windows Media Center is displayed at full screen, you cannot project using a network connection. Reduce the screen size.
Applications using the Windows DirectX function may not display images correctly.
Moving images are not displayed
Check
Is the computer's image signal being output to the LCD and the monitor?
(Only when projecting images from a laptop computer or a computer with a built-in LCD screen)
Are the contents of the moving image you are trying to project copyright protected?
Remedy
Change the image signal from the computer to external output only. Check your computer's documentation, or contact the computer's manufacturer.
The projector may not be able to project copyright protected moving images that are being played back on a computer.
For more details, see the user's guide supplied with the player.
Problem Solving
126
The playlist does not play.
Check
Have you saved a playlist to the SD card?
Remedy
The playlist may not have been saved correctly to the SD card. Check the data on the SD card.
"Not supported" is displayed
Check
Do the image signal resolution and the refresh rate correspond to the mode?
(Only when projecting computer images)
Remedy
Refer to the computer's documentation for how to change the image signal resolution and the refresh rate output from the computer.
s
"Supported Monitor Displays" p.157
"No Signal" is displayed
Check
Are the cables connected correctly?
Is the correct port selected?
Is the power for the computer or video source turned on?
Are the image signals being output to the projector?
(Only when projecting images from a laptop computer or a computer with a built-in LCD screen)
Remedy
Make sure that the necessary cables for projection are securely connected, or that the SD card is inserted correctly.
Check that no cables are disconnected and that there are no poor contacts in the cables.
Press the [HDMI], [LAN], or [ you want to project.
] button on the remote control to switch the image depending on the input source s
"Switching to the Target Image by Remote Control" p.36
Turn the power on for the equipment.
If the image signals are only being output to the computer's LCD monitor or to the accessory monitor, you need to change the output to an external destination as well as the computer's own monitor. For some computer models, when the image signals are output externally, they no longer appear on the LCD monitor or accessory monitor.
If the connection is made while the power of the projector or computer is already turned on, the Fn key (Function key) that changes the computer's image signal to external output may not work. Turn the power for the computer and the projector off and then back on again.
s Computer's documentation
Problem Solving
127
Images are fuzzy, out of focus, or distorted
Check
Is the focus adjusted correctly?
Is the projector at the correct distance?
Has condensation formed on the lens?
Remedy
Make sure that at least 20 minutes has passed after the projection starts, and press the [Focus] button on the remote control to adjust the focus.
s
Is it projecting outside of the recommended projection distance range?
Setup within the recommended range.
s
"Screen Size and Projection Distance" p.155
If the projector is suddenly taken from a cold environment to a warm environment, or if sudden ambient temperature changes occur, condensation may form on the surface of the lens, and this may cause the images to appear fuzzy. Set the projector up in the room about one hour before it is used. If condensation forms on the lens, turn the projector off and wait for the condensation to disappear.
Interference or distortion appear in images
Check
Are the cables connected correctly?
Is an extension cable being used?
Is the correct resolution selected?
(Only when projecting computer images)
Remedy
Make sure that the necessary cables for projection are securely connected, or that the SD card is inserted correctly.
Check that no cables are disconnected and that there are no poor contacts in the cables.
s
"Connecting to Various Devices" p.24
If an extension cable is used, electrical interference may affect the signals.
Set the computer so that the signals being output are compatible with the projector.
s
"Supported Monitor Displays" p.157
s Computer's documentation
The image is truncated (large) or small, the aspect is not suitable, or the image has been reversed
Check
Is the aspect adjusted correctly?
Remedy
Select Aspect from the Configuration menu to select an aspect suitable for the input source.
s
"Changing the Aspect Ratio of the Projected Image" p.54
Problem Solving
Check
Is Scale turned on?
Is the computer set for dual display?
(Only when projecting computer images)
Is the correct resolution selected?
(Only when projecting computer images)
Is the image direction correct?
Image colors are not right
Check
Is the image brightness adjusted correctly?
Are the cables connected correctly?
Is the Contrast
Is the color adjustment set correctly?
Are the color saturation and tint adjusted correctly?
128
Remedy
Set Scale to Off on the Configuration menu.
s Signal - Scale Scale
If dual display is activated in the Display Properties of the computer's Control Panel, only about half of the image on the computer screen is projected. To display the entire image on the computer screen, turn off the dual display setting.
s Computer video driver documentation
Set the computer so that the signals being output are compatible with the projector.
s
"Supported Monitor Displays" p.157
s Computer's documentation
Make the correct settings in Projection from the Configuration menu.
s
"Setting the Image Orientation (Projection)" p.28
Remedy
Adjust the Brightness setting from the Configuration menu.
s Image - Brightness
Make sure that the necessary cables for projection are securely connected, or that the SD card is inserted correctly.
Check that no cables are disconnected and that there are no poor contacts in the cables.
s
"Connecting to Various Devices" p.24
Adjust the Contrast setting from the Configuration menu.
s Image - Contrast
Adjust the Gamma setting from the Configuration menu.
s Image - Advanced
Adjust the Color Saturation and Tint settings from the Configuration menu.
s Image - Color Saturation , Tint
Problem Solving
129
Check
Is Light Source Calibration set correctly?
Remedy
If you are projecting using multiple projectors, and only some projectors change color, you may need to perform Light
Source Calibration.
Perform Light Source Calibration on all of the projectors.
s Reset - Light Source Calibration
If you do not want to start Light Source Calibration automatically, set Run Periodically to Off .
s Reset - Light Source Calibration - Run Periodically
Images appear dark
Check
Is the image brightness set correctly?
Is the Contrast
Remedy
Check the Brightness and Brightness Settings values from the Configuration menu.
s Image - Brightness
s Settings - Brightness Settings
Adjust the Contrast setting from the Configuration menu.
s Image - Contrast
Burning appears on the LCD panel.
Check
Reduces burning.
Remedy
Select Refresh Mode - Start from the Configuration menu.
s
Problems when Projection Starts
The projector does not turn on
Check
Did you press the [ t ] button on the remote control or the projector? Press the [ t ] button to turn on the power.
Remedy
Problem Solving
130
Check
Are the indicators switched off?
Remedy
The power cord is not connected correctly or power is not being supplied.
Disconnect and then reconnect the power cord.
Check that your electrical outlet or power source is functioning correctly.
Do the indicators turn on and off when the power cord is touched? There is probably a poor contact in the power cord, or the power cord may be defective. Reinsert the power cord. If this does not solve the problem, stop using the projector, disconnect the power cord from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s
Epson Projector Contact List
Is the correct setting for the Remote Receiver selected?
Check the Remote Receiver from the Configuration menu.
s Settings - Remote Receiver
Was the power cord plugged back in or was the breaker turned on immediately after direct shutdown?
If the operation described in the column on the left is performed when Direct Power On is set to On , the power may not turn back on. Press the [ t ] button to turn on the power.
Solving Network Problems
Solutions When Wireless Authentication Fails
Check
Check the date and time settings.
Check the security settings.
Remedy
If the wireless settings are correct, but authentication fails, you may need to update the Date & Time settings on the projector's Extended menu.
s
"Setting the Date and Time" p.30
Check the Security settings in the projector's Network menu.
s
"Setting Up Wireless Network Security" p.84
Solutions When You Cannot Access the Projector using a Web browser
Check
Are you using the correct user name and password?
Remedy
To open the home screen from a Web browser, enter "EPSONWEB" as the user name. (You cannot change the user ID.) Enter the password set in the projector's Network menu for options other than Remote . The default password is "admin".
s Network - Basic - Web Control Password
Problem Solving
131
Check
Can you access the network to which the projector is connected?
Remedy
If your Web browser is set up to connect through a proxy server, the Home screen cannot be displayed. Make settings for a connection without using a proxy server.
Cannot operate the SD card using a Web browser (save/delete playlist, upload data).
Check
Is the SD card write protected?
Release the write protection from the SD card.
Remedy
Email is not received even if a problem occurs in the projector
Check
Are you connected to the network?
Is Standby Mode set to Communication On ?
Is power being supplied to the projector?
Is the Mail Notification function set correctly in the
Configuration menu?
Remedy
(If an error shuts down the projector, the email may not be delivered.)
To use the Mail Notification function when the projector is in standby, set Communication On in Standby
Mode from the Configuration menu. Also, change the Port according to the network environment in which it is being used.
s Extended - Standby Mode
Check that your electrical outlet or power source is functioning correctly.
An error notification email is sent according to the Notifications settings in the Configuration menu. Check if it is set correctly.
s
Solutions When the Image Contains Static During Network Projection
Check
Check the signal status.
Remedy
Check for any obstacles between the access point, the computer, the mobile device, and the projector, and change their positions to improve communication. Make sure that the access point, the computer, the mobile device and the projector are not too far apart.
If the wireless connection is slow or your projected image contains noise, check for interference from other equipment, such as a Bluetooth device or microwave. Move the interfering device farther away or expand your wireless bandwidth.
Problem Solving
Other Problems
No sound can be heard or the sound is faint
Check
Check that the audio/video cable is securely attached to both the projector and audio source.
Is the projector volume set to the minimum?
Remedy
Disconnect the cable from the Audio Out port, and then reconnect the cable.
Adjust the volume so that sound can be heard.
s Settings - Volume
s
Adjust the volume so that sound can be heard.
Is the volume for the computer or from the image source set to the minimum?
Is A/V Mute active?
Press the [A/V Mute] button to release A/V Mute.
s
"Hiding the Image and Sound Temporarily (A/V Mute)" p.58
The remote control does not work
Check
Is the remote control light-emitting area pointing towards the remote receiver on the projector during operation?
Point the remote control towards the remote receiver.
s
"Remote control operating range" p.27
Remedy
Is the remote control too far from the projector?
Check the operating range.
s
"Remote control operating range" p.27
Set the projector up in a location where strong light does not shine onto the remote receiver.
Is direct sunlight or strong light from fluorescent lamps shining onto the remote receiver?
Is the correct setting for the Remote Receiver selected?
Check the Remote Receiver from the Configuration menu.
s Settings - Remote Receiver
Are the batteries dead or have the batteries been inserted correctly? Make sure the batteries are inserted correctly or replace the batteries with new ones if necessary.
s
"Inserting Batteries into the Remote Control" p.26
132
Problem Solving
133
I want to change the language for messages and menus
Check
Change the Language setting.
Remedy
Adjust the Language setting from the Configuration menu.
s Extended - Language
Solutions to Password Problems
Check
Has a password been set?
Has the correct password been entered?
Do you have the remote control?
Remedy
You may have turned on Password Protection without first setting a password. Try entering "0000" using the remote control.
If you enter an incorrect password too many times, a "Request Code" message is displayed. Make a note of this code, and then contact your local dealer or the nearest address provided in the Epson Projector Contact List. Provide the request code and proof of ownership for assistance in unlocking the projector.
If you lose the remote control you cannot enter a password. Order a new one from Epson.
"The battery that saves your clock settings is running low. " is displayed
Check
The internal power supply that saves your clock settings is running low.
Remedy
Contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s
Epson Projector Contact List
Detailed logs and error message are not displayed
Check
Depending on the environment, errors and warnings may not be displayed when turning on the projector after a sudden voltage drop, blackout, or power cut.
Remedy
Wait for at least 10 seconds after turning off the projector using the power button or pulling the plug out of the outlet before turning the projector back on or re-inserting the plug in the outlet. When the projector turns on, check the status information.
Problem Solving
134
Cannot control Art-Net correctly.
Check
Have you operated the projector using the remote control while controlling in Art-Net?
Remedy
If you operate the projector using the remote control while controlling the projector using Art-Net, settings made by the DMX controller or application software may not be applied to the projector. When you want to apply all the channel controls to the projector, set Channel 13 to "Cannot control", then set it back to "Can control".
s
About Event ID
135
Check the numbers and then apply the following countermeasures. If you cannot resolve the problem, contact your network administrator, or contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s
Epson Projector Contact List
Event ID
0432
0435
0434
0481
0482
0485
0433
0484
0483
04FE
0479
04FF
0891
0892
0893
0894
Cause
Failed to start the network software.
Network communication is unstable.
Cannot play transferred images.
Communication was disconnected from the computer.
The network software ended unexpectedly.
A system error occurred in the projector.
Restart the projector.
Check the network communication status, and reconnect after waiting for a while.
Restart the network software.
Restart the projector.
Remedy
Check the status of network communications. Restart the projector.
0898
0899
089A
089B
089C
089D
Cannot find an access point with the same SSID.
The WPA/WPA2 authentication type does not match.
The WEP/TKIP/AES encryption type does not match.
Communication was disconnected because the projector connected to an unauthorized access point.
Failed to acquire DHCP.
Other communication errors
The EAP authentication type is not the same.
EAP server authentication failed.
EAP client authentication failed.
Key exchange failed.
Set the computer, the access point, and the projector to the same SSID.
Check that the wireless LAN security settings are correct.
s Network - Wireless LAN
Contact your network administrator for more information.
Check that the DHCP server is operating correctly. If you are not using DHCP, set it to Off .
s Network - Wireless LAN
Wired LAN
If restarting the projector or network software does not solve the problem, contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s
Epson Projector Contact List
Check that the wireless LAN security settings are correct. Also, check if the certificate is installed correctly.
s Network - Wireless LAN
About Event ID
136
Event ID
0920
Cause
The internal power supply that saves your clock settings is running low.
Remedy
Contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s
Epson Projector Contact List
Maintenance
This chapter provides information on maintenance procedures to ensure the best level of performance from the projector for a long time to come.
Cleaning
138
You should clean the projector if it becomes dirty or if the quality of projected images starts to deteriorate.
Caution
When cleaning, disconnect the power plug from the outlet, or turn off the circuit breaker. Otherwise, it could cause an electric shock.
Attention
Do not rub the lens with harsh materials or subject the lens to shocks, as it can easily become damaged.
Cleaning the Projector's Surface
Clean the projector's surface by wiping it gently with a soft cloth.
If the projector is particularly dirty, moisten the cloth with water containing a small amount of neutral detergent, and then firmly wring the cloth dry before using it to wipe the projector's surface.
Attention
Do not use volatile substances such as wax, alcohol, or thinner to clean the projector's surface. The quality of the case may change or become discolored.
Cleaning the Air Intake Vent and the Air Exhaust
Vent
Use a vacuum cleaner to remove dust from the front of the Air intake vent and the Air exhaust vent.
Use a vacuum cleaner to clean dust from the slit in the side of the projector.
Cleaning the Lens
Use a commercially available cloth for cleaning glasses to gently wipe the lens.
Warning
Do not use sprays that contain flammable gas to remove dust and lint from the lens. The projector may catch fire due to the high internal temperature.
Image Maintenance
139
Color Uniformity
If you are concerned about uneven colors in the projected image, make adjustments using Color Uniformity.
s
"Adjusting uneven colors (Color Uniformity)" p.65
Refresh Mode
When still images or images that move a little are projected for an extended period, an afterimage (image burning) may remain in the projected image.
You can reduce burning using Refresh Mode.
s Reset - Refresh Mode
The power turns off after a set time has passed.
a • To use the effect functions, make sure you perform Refresh Mode regularly.
• If an after image (image burning) remains after performing Refresh
Mode, contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s
Epson Projector Contact List
• Under the following conditions, Refresh Mode stops automatically and the projector turns off.
- When receiving Message Broadcasting
- When receiving an error notification
- When a phase difference plate warning (error) occurs a b
Press the [Menu] button while projecting.
Select Refresh Mode from Reset , and then press the [ ] button.
c Select Timer , and then press the [ ] button.
d Use the [ ][ ] buttons to set the time, and then press the [ ] button.
Image Maintenance e f
Select Start , and then press the [ ] button.
Select Yes , and then press the [ ] button.
Light Source Calibration
Execute Light Source Calibration to correct the white balance in the light source. We recommend running this function periodically.
a •
Whenever the usage time reaches 100 hours, Light Source
Calibration starts automatically when the projector is turned off.
However, this does not start automatically when the projector is used continuously for more than 24 hours, or when direct shutdown is used regularly. Execute with Run Now , or set Light Source
Calibration using the scheduling function to adjust the light source periodically.
s Reset - Light Source Calibration
s
"Setting an Event Schedule" p.71
•
If you do not want to start Light Source Calibration automatically, set Run Periodically to Off .
s Reset - Light Source Calibration - Run Periodically
•
When Light Source Calibration is enabled, turn on the projector at least 20 minutes before the event.
140
Appendix
Monitoring and Controlling
142
Epson Projector Management
Epson Projector Management lets you carry out operations such as checking the status of multiple Epson projectors that are connected to a network at a computer monitor, and controlling the projectors from the computer.
Download the Epson Projector Management software from the following website.
http://www.epson.com
Using the Mail Notification Function to Report
Problems
When you set Mail Notification, notification messages are sent to the preset email addresses when a problem or warning occurs with a projector. This will enable the operator to be notified of problems with projectors even at locations away from the projectors.
s Network - Notifications - Mail Notification
a • Up to a maximum of three notification destinations (addresses) can be registered, and notification messages can be sent to all three destinations at once.
• If a projector develops a critical problem and suddenly stops working, it may not be able to send a message notifying an operator of the problem.
• If you set Standby Mode to Communication On , you can control the projector even if it is in standby mode (when the power is off).
s Extended - Standby Mode
Reading error notification mail
When the Mail Notification function is set to On and a problem or warning occurs in the projector, the following email will be sent.
Sender: The email address set in From
Subject: EPSON Projector
Line 1: The projector name where the problem has occurred
Line 2: The IP address set for the projector where the problem has occurred.
Line 3 and on: Details of the problem
The details of the problem are listed line by line. The main message contents are listed below.
•
Internal error
•
Fan related error
•
Sensor error
•
Laser error (Laser Error/Laser Does Not Turn On)
•
Laser warning
•
Retardation Plate Error
•
Internal temperature error
•
High-speed cooling in progress
•
No-signal
No Signal is input to the projector. Check the connection status or check that the power for the signal source is turned on.
See the following to deal with problems or warnings.
s
"Reading the Indicators" p.119
Monitoring and Controlling
143
Management Using SNMP
By setting SNMP to On in the Configuration menu, notification messages are sent to the specified computer when a problem or warning occurs. This allows you to check for problems with projectors even at locations away from the projectors.
s Network - Notifications - SNMP
a • SNMP should be managed by a network administrator or someone who is familiar with the network.
•
To use the SNMP function to monitor the projector, you need to install the SNMP manager program on your computer.
• The SNMP Agent for this projector complies with version 1
(SNMPv1).
• The managing function using SNMP cannot be used over wireless
LAN in Quick connection mode.
• Up to two destination IP addresses can be saved.
The main contents are listed below.
Power ON/OFF
Signal selection
Item
On
Off
HDMI
LAN
SD Player
Spotlight
A/V Mute On/Off On
Off
Command
PWR ON
PWR OFF
SOURCE 30
SOURCE 53
SOURCE 57
SOURCE 58
MUTE ON
MUTE OFF
Add a Carriage Return (CR) code (0Dh) to the end of each command and transmit.
For more details, contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s
Epson Projector Contact List
ESC/VP21 Commands
You can control the projector from an external device using ESC/VP21.
Command list
When the power ON command is transmitted to the projector, the power turns on and it enters warm-up mode. When the projector's power has turned on, a colon ":" (3Ah) is returned.
When a command is input, the projector executes the command and returns a ":", and then accepts the next command.
If the command being processed terminates abnormally, an error message is output and a ":" is returned.
About PJLink
PJLink was established by the JBMIA (Japan Business Machine and
Information System Industries Association) as a standard protocol for controlling network-compatible projector's as part of their efforts to standardize projector control protocols.
The projector complies with the PJLink Class2 standard established by the
JBMIA.
The port number used by the PJLink search function is 4352 (UDP).
You need to make network settings before you can use PJLink. See the following for more information on network settings.
s
Monitoring and Controlling
144
It complies with all commands except for the following commands defined by PJLink Class2, and agreement was confirmed by the PJLink standard adaptability verification.
URL: http://pjlink.jbmia.or.jp/english/
•
Non-compatible commands
Mute settings
Function
Image muting set
Audio muting set
PJLink Command
AVMT 11
AVMT 21
•
Enter the port name and the input source number
Input Source Number
HDMI
SD Player
Spotlight
LAN
Input Port Name
32
43
44
52
•
Manufacturer name displayed for "Manufacture name information query"
EPSON
•
Model name displayed for "Product name information query"
EPSON EV105/EV100
Visit the Crestron ® Web site for details on Crestron Connected ® . (Only
English-language displays are supported.) https://www.crestron.com/products/line/crestron-connected
The following provides an overview of Crestron Connected ® .
•
Remote operation using a Web browser
You can operate a projector from your computer just like using a remote control.
•
Monitoring and control with application software
You can use Crestron RoomView ® Express/Crestron Fusion ® provided by Crestron ® to monitor devices in the system, to communicate with the help desk, and to send emergency messages.
This manual describes how to perform operations on your computer using a Web browser.
a •
You can only enter single-byte alphanumeric characters and symbols.
•
The following functions cannot be used while using Crestron
Connected ® .
The Message Broadcasting feature in the Epson Projector
Management software
•
If you set Standby Mode to Communication On , you can control the projector even if it is in standby mode (when the power is off).
s Extended - Standby Mode
About Crestron Connected
®
Crestron Connected ® is an integrated control system provided by
Crestron ® . It can be used to monitor and control multiple devices connected on a network.
The projector supports the control protocol, and can therefore be used in a system built with Crestron Connected ® .
Operating a projector from your computer
Displaying the operation window
Check the following before carrying out any operations.
•
Make sure the computer and projector are connected to the network.
Monitoring and Controlling
•
Set Crestron Connected from the Network menu to On .
s Network - Others - Crestron Connected
a b
Start the Web browser on the computer.
Enter the IP address of the projector in the address field of the
Web browser, and press the Enter key on the keyboard.
The Epson Web Control home screen is displayed.
Using the operation window c Press Crestron Connected .
The operation window is displayed.
145
A You can perform the following operations when you click the buttons.
Power
Button
Vol-/Vol+
A/V Mute
Function
Turns the projector power on or off.
Adjusts the volume.
Turns the video and audio on or off.
s
"Hiding the Image and Sound Temporarily (A/V
B Switch to the image from the selected input source. To display input sources that are not shown in Source List, click (a) or (b) to scroll up or down. The current video signal input source is displayed in blue.
You can change the source name if necessary.
C You can perform the following operations when you click the buttons. To display buttons that are not shown in Source List, click (c) or (d) to scroll left or right.
Monitoring and Controlling
146
Contrast
Button
Brightness
Color
Sharpness
Zoom
D
The [ ] [ ] [ ] [ ] buttons perform the same operations as the [ ] [ ]
[ ] [ ] buttons on the remote control. You can perform the following operations when you click the other buttons.
Button
OK
Menu
Esc
Function
Performs the same operation as the [ ] button on the remote control.
s
Displays and closes the Configuration menu.
Performs the same operation as the [Esc] button on the remote control.
s
E You can perform the following operations when you click the tabs.
Tab
Function
Adjusts the difference between light and shade in the images.
Adjusts the image brightness.
Adjusts the color saturation for the images.
Adjusts the image sharpness.
Click the [ z ] button to enlarge the size of the projection.
Click the [ x ] button to reduce the size of the projection.
Click the [ ] [ ] [ ] [ ] buttons to change the position of an enlarged image.
Help
Function
Displays the Help Desk window. Used to send messages to, and receive messages from, the administrator using
Crestron Connected ® .
Info
Tools
Tab Function
Displays information on the projector that is currently connected.
Changes settings in the projector that is currently connected. See the next section.
Using the tools window
The following window is displayed when you click the Tools tab on the operation window. You can use this window to change settings in the projector that is currently connected.
Monitoring and Controlling
A Crestron Control
Make settings for Crestron ® central controllers.
B Projector
The following items can be set.
Item
Projector Name
Location
Assigned To
Function
Enter a name to differentiate the projector that is currently connected from other projectors on the network. (The name can contain up to 15 single-byte alphanumeric characters.)
Enter an installation location name for the projector that is currently connected on the network. (The name can contain up to 32 single-byte alphanumeric characters and symbols.)
Enter a user name for the projector. (The name can contain up to 32 single-byte alphanumeric characters and symbols.)
147
DHCP
Item
IP Address
Subnet Mask
Default Gateway
Send
Function
Select the Enabled check box to use DHCP. You cannot enter an IP address if DHCP is enabled.
Enter the IP address to assign to the currently connected projector.
Enter a subnet mask for the currently connected projector.
Enter the gateway address for the currently connected projector.
Click this button to confirm the changes made to the
Projector .
C Admin Password
Select the Enabled check box to require a password to open the Tools window.
The following items can be set.
Item
New Password
Confirm
Send
Function
Enter the new password when changing the password to open the Tools window. (The name can contain up to 26 single-byte alphanumeric characters.)
Enter the same password as you entered in New
Password . If the passwords are not the same, an error is displayed.
Click this button to confirm the changes made to the
Admin Password .
D User Password
Select the Enabled check box to require a password to open the operation window on the computer.
The following items can be set.
Monitoring and Controlling
Item
New Password
Confirm
Send
Function
Enter the new password when changing the password to open the operation window. (The name can contain up to 26 single-byte alphanumeric characters.)
Enter the same password as you entered in New
Password . If the passwords are not the same, an error is displayed.
Click this button to confirm the changes made to the
User Password .
148
Monitoring and Controlling
Art-Net
Art-Net is an Ethernet communication protocol based on the TCP/IP protocol.
You can control the projector by using a DMX controller or an application system.
Channel definitions
The following explains the channel definitions used when controlling the projector in Art-Net.
Channel
1
2
3
7
Function
Adjusting light (Dimming)
Shutter control
Switch source
Zoom
Operation
0% - 100%
Shutter
Non-operational
Shutter
Non-operational
HDMI
LAN
SD Player
Spotlight
Non-operational
(+) lens adjustment
Non-operational
(-) lens adjustment
Parameters
Open
Closed
40 - 255
Movement - Large 0 - 31
Movement - Me‐ dium
32 - 63
Movement - Small 64 - 95
96 -159
Movement - Small 160 - 191
Movement - Me‐ dium
192 - 223
0 - 255
0 - 63
64 - 191
192 - 255
0 - 7
8 - 15
16 - 23
24 - 31
32 - 39
Default
0
128
0
128
Operation Content
Sets the image brightness.
Enables/disables A/V Mute.
Changes to the specified source.
Zooms using the amount of movement specified.
149
Monitoring and Controlling
Channel
Function
8 Electronic focus
10 Content Playback
150
Non-operational
Playlist1
Playlist2
Playlist3
Playlist4
Playlist5
Playlist6
Playlist7
Playlist8
Playlist9
Playlist10
Playlist11
Playlist12
Playlist13
Playlist14
Operation
(+) lens adjustment
Non-operational
(-) lens adjustment
Parameters
Movement - Large 224 - 255
Movement - Large 0 - 31
Movement - Me‐ dium
32 - 63
Movement - Small 64 - 95
96 -159
Movement - Small 160 - 191
Movement - Me‐ dium
192 - 223
Movement - Large 224 - 255
0 - 3
4 - 7
8 - 11
12 - 15
16 - 19
20 - 23
24 - 27
28 - 31
32 - 35
36 - 39
40 - 43
44 - 47
48 - 51
52 - 55
56 - 59
Default
128
0
Performs electronic focus using the amount of movement specified.
Operation Content
Plays the specified playlist.
Monitoring and Controlling
Channel
Function
10 Content Playback
Playlist25
Playlist26
Playlist27
Playlist28
Playlist29
Playlist30
Playlist31
Playlist32
Playlist33
Playlist34
Playlist15
Playlist16
Playlist17
Playlist18
Playlist19
Playlist20
Playlist21
Playlist22
Playlist23
Playlist24
Playlist35
Playlist36
Playlist37
Playlist38
Playlist39
Operation Parameters
100 - 103
104 - 107
108 - 111
112 - 115
116 - 119
120 - 123
124 - 127
128 - 131
132 - 135
136 - 139
60 - 63
64 - 67
68 - 71
72 - 75
76 - 79
80 - 83
84 - 87
88 - 91
92 - 95
96 - 99
140 - 143
144 - 147
148 - 151
152 - 155
156 - 159
0
Default Operation Content
Plays the specified playlist.
151
Monitoring and Controlling
152
Channel
10
Function
Content Playback
11 Power control
13 Lock
Operation
Playlist40
Playlist41
Playlist42
Playlist43
Playlist44
Playlist45
Playlist46
Playlist47
Playlist48
Playlist49
Playlist50
Non-operational
Power off
Non-operational
Power on
Cannot control
Can control
Parameters
160 - 163
164 - 167
168 - 171
172 - 175
176 - 179
180 - 183
184 - 187
188 - 191
192 - 195
196 - 199
200 - 203
204 - 255
0 - 63
64 - 191
192 - 255
0 - 127
128 - 255
0
Default Operation Content
Plays the specified playlist.
128
0
Turns the projector power on or off.
Enables/disables Art-Net operations.
a
While controlling the projector using Art-Net and performing operations from the remote control, settings made by the DMX controller or application software may differ from the actual projector's status. When you want to apply all the channel controls to the projector, set Channel 13 to "Cannot control", then set it back to "Can control".
Monitoring and Controlling
Web API
You can operate the projector using Web API.
You can enable Web API from a Web browser.
a b c
Open the Epson Web Control home screen from your Web browser.
Press the Developer's Menu button.
Set Enable API to On .
s
"Operating Using Epson Web Control (Web Browser)" p.40
The projector supports the following Web APIs.
URL http://<ip address>/api/v01/contentmgr/remote/power/on http://<ip address>/api/v01/contentmgr/remote/power/off http://<ip address>/api/v01/contentmgr/playlist/play/:id http://<ip address>/api/v01/contentmgr/playlist/stop
Supported methods Explanation
GET/POST/PUT
GET/POST/PUT
GET/POST/PUT
GET/POST/PUT
Turns the projector on.
(It takes a while for the WebAPI to respond.)
Turns the projector off.
Plays the specified ID playlist.
Enter the ID for the playlist in :id. You can check the playlist ID from the Developer's Menu on the home screen.
Stops the playlist currently being played.
Enter the IP address for the projector in <ip address>.
For example, a URL instructing a projector with the IP address 192.168.0.2 to playback playlist ID 3 would look like this: http://192.168.0.2/api/v01/contentmgr/playlist/play/3
If secure HTTP is enabled, change the http in the URL to https.
153
List of Optional Accessories
The following optional accessories are available. Please purchase these products as and when needed. The following list of optional accessories and consumables is current as of: April 2018. Details of accessories are subject to change without notice and availability may vary depending on the country of purchase.
Lighting Track Mount(White) ELPMB54W
Lighting Track Mount(Black) ELPMB54B
Use when installing the projector on a lighting track.
Floor Stand(White) ELPMB55W
Floor Stand(Black) ELPMB55B
Use when installing the projector on the floor.
* Special expertise is required to suspend the projector from a ceiling or mount it on a wall. Make sure you contact a professional.
154
Screen Size and Projection Distance
H
W
H
W
A Projection distance
B Center of lens
16:10 Screen Size
60"
80"
100"
120"
29"
30"
40"
50"
63x39
64x40
86x54
108x67
129x81
172x108
215x135
258x162
A
Minimum (Wide) to maximum (Tele)
85 to 136
88 to 141
118 to 189
149 to 237
179 to 285
239 to 381
300 to 476
360 to 572
Unit: cm
155
16:10 Screen Size
133"
150"
286x179
323x202
4:3 Screen Size
60"
80"
100"
120"
25"
30"
40"
50"
133"
150"
200"
51x38
61x46
81x61
102x76
122x91
163x122
203x152
244x183
270x203
305x229
406x305
16:9 Screen Size
28"
30"
40"
50"
60"
62x35
66x37
89x50
111x62
133x75
A
Minimum (Wide) to maximum (Tele)
400 to 634
451 to 716
A
Minimum (Wide) to maximum (Tele)
83
100 to 160
134 to 214
169 to 268
203 to 323
271 to 431
340 to 540
408 to 648
453 to 719
511 to 811
682 to 1082
Unit: cm
Unit: cm
A
Minimum (Wide) to maximum (Tele)
84
91 to 145
122 to 194
153 to 243
184 to 293
Screen Size and Projection Distance
16:9 Screen Size
80"
100"
133"
150"
200"
250"
177x100
221x125
294x166
332x187
443x249
553x311
A
Minimum (Wide) to maximum (Tele)
246 to 391
308 to 490
411 to 652
464 to 736
619 to 982
775 to 1228
* When the aspect ratio is 16:9, the top edge of the projected image shifts from the lens center.
156
Supported Monitor Displays
When the resolution of the input signals is larger than the projector's panel resolution, the image quality may decline.
Signals with a check mark are supported.
Signal type Signal format Resolution (Dot) V Sync (Hz)
RGB (8bit)
HDMI
4:4:4
YCbCr (8bit)
4:2:2
PC VGA
SVGA
XGA
WXGA
WXGA+
WXGA++
SXGA
640
800
1024
1280
1280
1366
1440
1600
1280
480
600
768
768
800
768
900
900
960
60
70
75
85
60
60
75
60
72
75
85
60
72
75
85
85
60
60
85
60
60
75
4:2:0
157
Supported Monitor Displays
Signal type
SD
HD
Signal format
SXGA+
WSXGA+
UXGA
1920x1080
WUXGA RB *
SDTV (480i)
SDTV (576i)
SDTV (480p)
SDTV (576p)
HDTV (720p)
HDTV (1080i)
HDTV (1080p)
1920
720
720
720
720
1280
1920
1920
1400
1680
1600
1920
1200
480
576
480
576
720
1080
1080
1050
1050
1200
1080
Resolution (Dot) V Sync (Hz)
RGB (8bit)
HDMI
4:4:4
YCbCr (8bit)
4:2:2 4:2:0
1280 1024
60
50
60
60
60
50
60
85
60
75
60
75
85
60
75
60
24
30
50
50
50
60
50
158
Supported Monitor Displays
Signal type Signal format
* Based on VESA CVT-RB (Reduced Blanking)
Resolution (Dot) V Sync (Hz)
RGB (8bit)
HDMI
4:4:4
YCbCr (8bit)
4:2:2 4:2:0
60
159
Specifications
Projector General Specifications
Product name
Dimensions
LCD panel size
Display method
Resolution
Focus adjustment
Zoom adjustment
Light source
Light source output power
Wavelength
Light source life expectancy
Power supply
Power consumption
100 to 120 V area
220 to 240 V area
Operating altitude
Operating temperature
Storage temperature
EV-100 (White)
EV-105 (Black)
Image projection unit: Diameter 175 x Depth 260 mm
Power unit: Width 361 x Depth 110 x Height 65 mm (without power adapter cover)
Power unit: Width 459 x Depth 110 x Height 65 mm (with power adapter cover)
0.59" Wide
Polysilicon TFT active matrix
1,024,000
WXGA (1280 (horizontal) x 800 (vertical) dots) x3
Automatic
Automatic (1-2.21)
(Optical 1-1.58, Digital 1-1.4)
Laser diode
Up to 88 W
440 to 460 nm
Approximately 20,000 hours (Light Source Mode: Normal, Quiet)
Approximately 30,000 hours (Light Source Mode: Extended)
100-240 V AC±10% 50/60 Hz 1.8 to 0.8 A
Rated power consumption: 173 W
Standby power consumption (Communication On): 2.0 W
Standby power consumption (Communication Off): 0.3 W
Rated power consumption: 170 W
Standby power consumption (Communication On): 2.0 W
Standby power consumption (Communication Off): 0.3 W
Altitude 0 to 3,048 m
+5 to +40˚C * (No condensation)
-10 to +60˚C (No condensation)
160
Specifications
161
Mass Approx. 6.9 kg (main projector section approx. 5.0 kg/Direct Mount approx. 1.9 kg)
* If the surrounding temperature gets too high, the brightness is automatically dimmed.
(Approximately 40˚C at an altitude of 0 to 1,500 m, and approximately 35˚C at an altitude of 1,501 to 3,048 m; however, this may vary depending on the surroundings and so on.)
Connectors
HDMI port
Audio Out port
LAN port
USB port (dedicated power supply)
SD card slot
1
1
1
1
1
HDMI HDCP supported (Audio is only supported by PCM)
Stereo mini jack (3.5Φ)
RJ-45
USB connector (Type A)
SDHC/microSDHC, Class10 or higher, Maximum of 32 GB, FAT16/FAT32 supported
This product is also designed for IT power distribution system with phase-to-phase voltage 230V.
Specifications
162
Supplier's DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B Personal Computers
We:
Located at:
Tel:
Epson America, Inc.
3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
562-981-3840
Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each product marketed, is identical to the representative unit tested and found to be compliant with the standards. Records maintained continue to reflect the equipment being produced can be expected to be within the variation accepted, due to quantity production and testing on a statistical basis as required by 47CFR 2.909.
Trade Name: EPSON
Type of Product:
Model:
LCD Projector
H868C
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
•
Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
WARNING
The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification or Declaration of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.
Appearance
110
5xM4-9
36
18
31
299
361
31.5
16 4xM4-9
163
Units: mm
6
A Center of lens
B Distance from center of lens to mount fixing points
175
260
265
115
Glossary
164
This section briefly explains the difficult terms that are not explained in the text of this guide. For details, refer to other commercially available publications.
Aspect Ratio
Contrast
DHCP
Gateway Address
HDCP
HDTV
Infrastructure mode
Interlace
IP Address
Progressive
Refresh Rate
SDTV
SNMP
Subnet Mask
Sync.
Trap IP Address
The ratio between an image's length and its height. Screens with a horizontal:vertical ratio of 16:9, such as HDTV screens, are known as wide screens.
SDTV and general computer displays have an aspect ratio of 4:3.
The relative brightness of the light and dark areas of an image can be increased or decreased to make text and graphics stand out more clearly, or to make them appear softer. Adjusting this particular property of an image is called contrast adjustment.
An abbreviation of Dynamic Host Configuration Protocol, this protocol automatically assigns an IP Address
g to equipment connected to a network.
This is a server (router) for communicating across a network (subnet) divided according to Subnet Mask
.
HDCP is an abbreviation for High-bandwidth Digital Content Protection. It is used to prevent illegal copying and protect copyrights by encrypting digital signals sent over DVI and HDMI ports. HDCP2.2 is a copyright protection standard for 4K content.
An abbreviation for High-Definition Television that refers to high-definition systems which satisfy the following conditions.
•
Vertical resolution of 720p or 1080i or greater (p = Progressive
•
Screen Aspect Ratio
of 16:9
A method for wireless LAN connection in which devices communicate through access points.
Transmits information needed to create one screen by sending every other line, starting from the top of the image and working down to the bottom.
Images are more likely to flicker because one frame is displayed every other line.
A number to identify a computer connected to a network.
Projects information to create one screen at a time, displaying the image for one frame. Even though the number of scan lines is the same, the amount of flicker in images decreases because the volume of information has doubled compared with an interlace system.
The light-emitting element of a display maintains the same luminosity and color for an extremely short time. Because of this, the image must be scanned many times per second to refresh the light-emitting element. The number of refresh operations per second is called the Refresh rate and is expressed in hertz (Hz).
An abbreviation for Standard Definition Television that refers to standard television systems which do not satisfy the conditions for HDTV
Definition Television.
An abbreviation for Simple Network Management Protocol, which is the protocol for monitoring and controlling devices such as routers and computers connected to a TCP/IP network.
This is a numerical value that defines the number of bits used for the network address on a divided network (subnet) from the IP address.
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are not of a good quality. The process of matching the phases of these signals (the relative position of the crests and the troughs in the signal) is called
Synchronization. If the signals are not synchronized, flickering, blurriness, and horizontal interference occur.
This is the IP Address
g for the destination computer used for error notification in SNMP.
General Notes
165
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko
Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed for damages resulting from the use of the information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as
Original Epson Products or Epson Approved Products by Seiko Epson Corporation.
The contents of this guide may be changed or updated without further notice.
Illustrations in this guide and the actual projector may differ.
Restriction of Use
When this product is used for applications requiring high reliability/safety such as transportation devices related to aviation, rail, marine, automotive etc.; disaster prevention devices; various safety devices etc; or functional/precision devices etc, you should use this product only after giving consideration to including fail-safes and redundancies into your design to maintain safety and total system reliability. Because this product was not intended for use in applications requiring extremely high reliability/safety such as aerospace equipment, main communication equipment, nuclear power control equipment, or medical equipment related to direct medical care etc, please make your own judgment on this product’s suitability after a full evaluation.
Trademarks and Copyrights
"EPSON" is a registered trademark of Seiko Epson Corporation. "EXCEED YOUR
VISION" are trademarks or registered trademarks of Seiko Epson Corporation.
Mac, Mac OS, OS X, and iOS are trademarks of Apple Inc.
Microsoft, Windows, Windows Server, Microsoft Edge, Windows Media, and the
Windows logo are trademarks or registered trademarks of Microsoft Corporation in the
United States and/or other countries.
App Store is a service mark of Apple Inc.
Android, Chrome, Chromebook, and Google Play are trademarks of Google Inc.
HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing LLC.
SDHC Logo is a trademark of SD-3C, LLC.
PJLink trademark is a trademark applied for registration or is already registered in
Japan, the United States of America and other countries and areas.
WPA ™ and WPA2 ™ are registered trademarks of the Wi-Fi Alliance.
"QR Code" is a registered trademark of DENSO WAVE INCORPORATED.
Crestron, Crestron Connected, Crestron RoomView, and Crestron Fusion are registered trademarks of Crestron Electronics, Inc.
Art-Net ™ Designed by and Copyright Artistic Licence Holdings Ltd.
Extron ® and XTP ® are registered trademarks of Extron Electronics.
This product includes RSA BSAFETM software from RSA Security Inc. RSA is a registered trademark of RSA Security Inc. BSAFE is a registered trademark of RSA
Security Inc. in the United States and/or other countries.
Other product names used herein are also for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
©SEIKO EPSON CORPORATION 2018. All rights reserved.
General Notes
Indication of the manufacturer and the importer in accordance with requirements of EU directive
Manufacturer: SEIKO EPSON CORPORATION
Address: 3-5, Owa 3-chome, Suwa-shi, Nagano-ken 392-8502 Japan
Telephone: 81-266-52-3131 http://www.epson.com/
Importer: EPSON EUROPE B.V.
Address: Atlas Arena, Asia Building, Hoogoorddreef 5, 1101 BA Amsterdam
Zuidoost The Netherlands
Telephone: 31-20-314-5000 http://www.epson.eu/
166
List of Safety Symbols
The following table lists the meaning of the safety symbols labeled on the equipment.
No.
Symbol mark Meaning
A
B
Approved standards
IEC60417
No. 5007
IEC60417
No. 5008
"ON" (power)
To indicate connection to the mains.
"OFF" (power)
To indicate disconnection from the mains.
C
D
E
F
G
H
IEC60417
No. 5009
ISO7000
No. 0434B
IEC3864-B3.1
IEC60417
No. 5041
IEC60417
No. 6042
ISO3864-B3.6
IEC60417
No. 5957
IEC60417
No. 5926
Stand-by
To identify the switch or switch position by means of which part of the equipment is switched on in order to bring it into the stand-by condition.
Caution
To identify general caution when using the product.
Caution, hot surface
To indicate that the marked item can be hot and should not be touched without taking care.
Caution, risk of electric shock
To identify equipment that has risk of electric shock.
For indoor use only
To identify electrical equipment designed primarily for indoor use.
Polarity of d.c. power connector
To identify the positive and negative connections (the polarity) on a piece of equipment to which a d.c. power supply may be connected.
167
No.
Symbol mark
I
Approved standards
IEC60417
No. 5001B
J
K
L
M
N
O
IEC60417
No. 5002
IEC60417
No. 5019
IEC60417
No. 5017
IEC60417
No. 5032
IEC60417
No. 5031
IEC60417
No. 5172
Meaning
Battery, general
On battery powered equipment. To identify a device for instance a cover for the battery compartment, or the connector terminals.
Positioning of cell
To identify the battery holder itself and to identify the positioning of the cell(s) inside the battery holder.
Protective earth
To identify any terminal which is intended for connection to an external conductor for protection against electric shock in case of a fault, or the terminal of a protective earth electrode.
Earth
To identify an earth (ground) terminal in cases where symbol No. 11 is not explicitly required.
Alternating current
To indicate on the rating plate that the equipment is suitable for alternating current only; to identify relevant terminals.
Direct current
To indicate on the rating plate that the equipment is suitable for direct current only; to identify relevant terminals.
Class II equipment
To identify equipment meeting the safety requirements specified for Class II equipment according to IEC 61140.
List of Safety Symbols
No.
Symbol mark
P
Approved standards
ISO 3864
Q
R
S
T
U
V
W
X
Y
Z
ISO 3864
---
---
ISO 3864
IEC60825-1
ISO 3864
IEC60417
No. 5266
ISO 3864
IEC60417
No. 5057
IEC
60417-6056
IEC
60417-6043
---
Meaning
General prohibition
To identify actions or operations that are prohibited.
Contact prohibition
To indicate injury that could occur due to touching a specific part of the equipment.
Never look into the projection lens while the projector is on.
To indicate that you should not place anything on the projector.
Caution, laser radiation
To indicate the equipment has a laser radiation part.
Disassembly prohibition
To indicate a risk of injury, such as electric shock, if the equipment is disassembled.
Standby, partial standby
To indicate that part of the equipment is in the ready status.
Caution, movable parts
To indicate that you must keep away from movable parts according to protection standards.
Caution (Moving Fan Blades)
As a safety precaution, stay away from the moving fan blades.
Caution (Sharp Corners)
To indicate sharp corners that should not be touched.
To indicate that looking into the lens while projecting is prohibited.
168
Index
169
A
A/V Mute ...................................................... 58
Air exhaust vent ........................................... 15
Air intake vent .............................................. 14
Art-Net ............................................... 111, 149
Aspect ...................................................... 54, 97
Audio Out port ............................................ 16
Auto Power On .......................................... 100
B
Ball joint ........................................................ 14
Basic menu ................................................. 104
Batch setup function ................................. 114
Brightness ............................................... 47, 96
Brightness Settings ...................................... 52
C
Cleaning ...................................................... 138
Cleaning the projector's surface .............. 138
Color Adjustment ........................................ 55
Color adjustment ......................................... 97
Color Filter ................................................... 46
Color Matching ................................... 67, 101
Color Mode .................................... 52, 96, 101
Color Saturation .......................................... 96
Color Uniformity .......................... 65, 99, 101
Configuration menu .................................... 92
Content Playback ......................................... 99
Contrast ........................................................ 96
Crestron Connected .......................... 110, 144
D
Date & Time ......................................... 30, 100
DHCP .................................................. 106, 108
Direct Mount fixing points ........................ 17
Direct Power On ........................................ 100
Display ........................................................... 99
Distance ...................................................... 155
Dynamic Contrast ................................. 54, 97
E
Edge Blending ...................................... 62, 101
Epson iProjection ........................................ 40
Epson Projector Management ................. 142
Epson Web Control ..................................... 40
ESC/VP21 ................................................... 143
Event ID ...................................................... 112
Extended menu ............................................ 99
F
Floor Stand fixing points ............................ 17
Focus .............................................................. 49
Front ............................................................ 100
G
Gateway Address ............................... 106, 108
H
H/V-Keystone ........................................ 50, 98
HDMI port ................................................... 16
High Altitude Mode .................................. 100
I
Image Menu ................................................. 96
Indicators .............................................. 15, 119
Info menu ................................................... 112
Input Signal ................................................ 112
IP Address .......................................... 106, 108
K
Keystone ................................................. 49, 98
L
M
Mail Notification ............................... 109, 142
Message Broadcasting ............................... 111
Messages ....................................................... 99
Moderator Password ................................. 104
Monitor displays ........................................ 157
Multi-Projection .................................. 60, 101
N
LAN port ....................................................... 16
Language ..................................................... 101
Light Source Calibration .............. 6, 113, 140
Lighting Track Mount fixing points ......... 17
Network Configuration ............................ 103
Network information ................................ 102
Network menu ........................................... 102
Notification email address 1/2/3 ............. 110
Notifications menu .................................... 109
Index
170
O
Operating Temperature ............................ 160
Operation .................................................... 100
Others .......................................................... 110
Overheating ................................................ 121
Overlay Effect ............................................... 45
P
Q
QR code ......................................................... 86
Quick Corner ......................................... 51, 98
R
Part names and functions ........................... 14
Password Protection .................................... 73
PJLink .......................................................... 143
PJLink Password ........................................ 104
Playlist ........................................................... 38
Port Number .............................................. 109
Power adapter cover .................................... 16
Power inlet .................................................... 16
Priority Gateway ........................................ 110
Projection ................................................... 100
Projector ................................................. 34, 35
Projector ID .................................................. 61
Projector keyword ..................................... 104
Projector Name .......................................... 104
Reading mail ............................................... 142
Rear .............................................................. 100
Refresh Mode ..................................... 113, 139
Refresh Rate ................................................ 112
Remote control ............................................ 18
Remote receiver ........................................... 15
Replacing batteries ....................................... 26
Reset All ...................................................... 113
Reset menu ................................................. 113
Resolution ................................................... 112
S
Scale ....................................................... 97, 101
Schedule ........................................................ 71
Schedule Settings ....................................... 101
Screen size ................................................... 155
SD card .......................................................... 38
SD card slot ................................................... 16
Search Access Point ................................... 107
Secure HTTP ........................................ 88, 110
Serial Number ............................................ 112
Settings menu ............................................... 98
Shape Filter ................................................... 45
Sharpness ...................................................... 96
Signal menu .................................................. 97
SMTP Server ............................................... 109
SNMP .......................................................... 143
Soft keyboard ............................................. 103
Source .......................................................... 112
Specifications ............................................. 160
Spotlight ........................................................ 37
Standby Mode ............................................ 100
Startup Screen .............................................. 99
Status ........................................................... 112
Storage temperature .................................. 160
Subnet Mask ....................................... 106, 108
Supported monitor displays ..................... 157
Sync Info ..................................................... 112
Synchronized playback ............................... 69
T
Test Pattern ............................................ 48, 98
Tint ................................................................ 96
Trap IP Address 1/2 .................................. 110
U
USB-A port ................................................... 16
User Button .................................................. 98
User's Logo ................................................... 70
V
Volume ................................................... 57, 98
W
WEB API .................................................... 153
Web Control Password ............................. 104
Web Server Cert. ........................................ 110
Web Server Certificate ................................ 88
White Balance .............................................. 97
Wired LAN menu ...................................... 108
Wireless LAN menu .................................. 105
Z
Zoom ............................................................. 49
डाउनलोड
सार्वजनिक लिंक अपडेट किया गया
आपकी चैट का सार्वजनिक लिंक अपडेट कर दिया गया है. You may view and manage your chat links after registration here.
दस्तावेज़ सार्वजनिक लिंक
विज्ञापन
मुख्य विशेषताएं
Integrated lighting and digital display — project dynamic, experiential content to engage audiences in retail, hospitality and event spaces, showrooms and museums
Create head-turning digital signage — illuminate and project on virtually any surface or material, for digital art, commercial signage and décor applications
Blends in discreetly — sleek, white spotlight design easily blends into its surroundings, offering vertical and horizontal rotation, with flexible mounting on tracks, floors, walls or ceilings
Breakthrough laser technology — features a laser light source that lasts up to 20,000 hours, plus a sealed optical engine, for amazing image quality matched by outstanding performance
Robust management and control tools — via Epson’s Web-based application or over the network with Crestron®, Art-Net and more
Scalable, for an array of applications — install multiple LightScene projectors and utilize Edge Blending technology for versatile, breathtaking displays
Easily programmable — includes templates, effects, color filters and customizable options; playlist and playback function allows for seamless content management for single or multiple LightScene projectors
Flexible positioning — 1.58x powered optical zoom, plus powered focus, allows the projector to be installed in both large and small spaces
Expansive connectivity — HDMI®, RJ-45, wired and wireless LAN, and SD card slot for direct content storage when needed
Bright visual display system — 2,000 lumens equal color and white brightness for vibrant, rich color