OSD Audio SS2V70 Mono 70V 2-Zone Brushed Aluminum Finish Speaker Selector Owner's Manual
Add to my manuals2 Pages
OSD Audio SS2V70 is a 2-zone, 70V mono speaker selector with built-in 100W mono volume control for each zone. It features a noise-free rotary knob and pushbutton for easy volume adjustment. The SS2V70 allows you to connect multiple speakers to a single amplifier and control the volume of each zone independently. It has a straight pass-thru output for daisy-chaining additional speaker selectors. The selector is designed for commercial applications and offers reliable performance with excellent frequency response and low insertion loss.
advertisement
New SSVC2V7; 2 Zone, 70V Mono Speaker Selector with Built in 100W
70V Mono Volume Control x 2 and Straight Pass Thru Output
The SSVC2V7 is a unique 70V Speaker Selector featuring…
2 independent Zones each controlled by a 100Watt 70V Mono Volume Control featuring a Rotary style
Knob. Each zone has On/Off switch as well. The unit has a single 2 conductor input and direct pass thru allowing to stack additional SSVC27V Speaker selectors only limited by your application. Standard 70V rules apply to the number of speakers used per zone, matching the available power from the 70V amplifier
Note #1: The On/Off switch is supply so you can turn off each zone completely not just depend on the Volume Control to turn so the sound down to inaudible levels. The knob would need to be turned all the way counterclockwise for full off
Zone 1
On/Off
Switch
Front Panel SSVC2V7
Zone 1
Volume
Knob
Zone 2
Volume
Knob
Zone 1
On/Off
Switch
Back Panel SSVC2V7
Note #2: The Thru output comes directly from the Input, it does not go through the transformer allowing you to stack multiple SSVC7V.
ZONE 1 Speaker
Output
ZONE 1 Speaker
Output
Input from Amplifier
Specifications
• Power Handling:
• Frequency Response:
• Selector Type:
• Steps:
• Connection Type:
• Wire Size Acceptance:
• Amplifier Protection:
Straight Thru
Output
100 Watts Per Channel/Zone Mono Single Channel
20Hz-22KHz (+0 dB, -0 dB)
Noise-Free, front access On/Off Pushbutton and Rotary Knob
33 dB, 10 steps plus full of (step 11)f
Removable Input/output Connectors
16 Gauge 2 Conductor,
70V Mono only No Impedance Protection Needed
New SSVC2V7; 2 Zone, 70V
Mono Speaker Selector
Features and Specifications
DECORA style high-quality auto transformer provides advantages of excellent frequency response, low insertion loss and reliable performance for volume control applications in 25 and 70 volt systems. Attenuation is accomplished in ten make before break steps plus positive off position (no stop between maximum and off position to prevent switch damage). The Attenuator features removable input/output terminal blocks, Two in, two out and two optional for through output for daisy chain option. An attractive alternative to Commercial series attenuators mounts into most single gang E.O boxes. UL Listed White, Almond and Ivory Plastic Plates with Matching Skirted Knobs in DECORA® Style
Power Rating:
The Internal Volume Controls (2) are rated at
100W so the speaker(s) connected to it needs the transformer setting to be equal to or less than the rated watts of each MVC. You can have multiple speakers connected to one MVC but total wattage must 80% or less than the rated Wattage of the each of the internal 100 Watt Volume Controls.
Internal Volume
Control Specs:
10 Step, 33dB
Plus Full Off
5
4
7
6
STEP ATTENUATION
10 Full Volume 0dB
9
8
3dB
3dB minus 3dB minus 6dB
3dB
3dB
3dB
3dB minus 9dB minus 12dB minus 15dB minus 18dB
3
2
3dB
6dB minus 21dB minus 27dB
1 6dB minus 33dB
Picking the right Distribution Amplifier:
0 0dB Speaker off
To start with the Amplifier must have a 70Volt output. It must have an output power rating equal to or greater than the total wattage of the system once you have calculated what each speaker should be set to and the total sum of those settings. If you had four speakers at 5 watts each (20 total) and one speaker set to 10 watts (20 + 10 = 30) your amplifier must be rated at least 30 watts minimum. If you had five speakers at 10 watts each (50 total) and another 5 five speakers at 5 watts each (25 + 50 = 75) you would need a amplifier rated at a minimum 75 watts.
Some companies recommend the total should be closer to 80% of the minimum rating of the amplifier. It is also a good idea to install an amplifier with more than enough power in case you want to add more speakers later.
Key Point: The Power rating of the amplifier is determined by the transformer settings, not the attenuator Rating, The rated power of the Attenuator is based upon the minimum setting of the transformer taps which have to be equal to or less than the rated wattage of the respective MVC Attenuator
OSD Audio Limited Warranty
OSD Audio will repair or replace any defect it in material or workmanship which occurs during normal use of this product with new or rebuilt parts free of charge in the US for five years from date of original purchase. This warranty does not cover damages in shipment, failure caused by other products not supplied by OSD Audio or failures due to accident, misuse, or alteration of the equipment. This warranty is extended only to the original purchaser and a purchase receipt, invoice or other proof of original date will be required before warranty repairs are provided
Mail in service can be obtained during period by emailing [email protected]
. A return authorization number must be obtained in advance and be marked on the outside of the shipping carton.
This warranty gives you specific legal rights and may have other rights (which vary from state to state). If a problem with this product develops during or after the warranty period please contact OSD Audio or your dealer
OSD Audio · 775 Columbia St., Brea CA 92821 · www.osdaudio.com
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project