&BARSKA
User’s Manual for Fireproof
Biometric Safe
Read all instructions before using this safe.
- Under Factory Default mode, the safe can be opened by any
fingerprint. For security purposes, please register your own
fingerprint immediately before you start to use the safe.
- Register at least two different fingerprints and test a few
times before closing the safe door.
- Test with a non-registered fingerprint. If the safe opens, the
safe is still in Factory Default mode.
- Avoid leaving door open and unattended; it will allow
unauthorized individuals to reprogram the safe, gaining full
access to the safe and the contents.
- Body of safe consists of two steel plates filled with a
fire-retardant material.
- Do NOT store combustible materials in this unit.
- In the event of fire, we recommend caution when opening
the safe. If you feel unsure about opening the safe because
of the contents stored, contact your local fire department
for assistance.
- Test the Emergency Keys and store them in a secure place;
NOT inside of the safe.
- Test and make sure the safe works properly
before mounting.
- Mount the safe before use, the safe may tip forward if not
properly mounted.
- Keep children away from safe; they should not play with or
around the safe at any time. Children at play could
accidentally get locked inside the safe or accidently pull on
the safe door causing safe to tip over if not
properly mounted.
- Failure to follow these warnings could result in serious injury
or death.
NOTE: BARSKA is not responsible for any damage or lost
contents in the safe due to moisture.
NOTE: BARSKA is not responsible if the safe or its contents
gets lost or stolen.
* Actual Model May Vary
Parts
A. Handle E. Battery Compartment
B. Emergency Lock Cover & F. Key Hook
Key Access G. Initialization Button
C. Fingerprint Scanner H. Net Pocket
D. Indicator Lights
Getting Started
1. Remove Emergency Keys from accessory package.
2. To expose the Emergency Key access, remove Emergency
Lock cover (B).
3. Insert the Emergency Key and turn counter clockwise.
4. Turn the handle (A) clockwise to open the door.
NOTE: Once operation is finished, please pull out the
Emergency Key and keep it in a safe place; NOT inside of the
safe.
Install Batteries
1. With the door open, remove the battery cover (E) on side of
door by sliding the cover.
2. Insert 4 AA batteries by lining them up in a manner as
indicated by the “+” and “-“signs.
3. Put the arrow of the battery cover align to the arrow on the
compartment, slide the batteries cover back into place.
Restore the battery compartment cover.
NOTE: DO NOT use any other
type of non-alkaline battery.
DO NOT mix new and old |
batteries. DO NOT mix alkaline
and non-alkaline batteries.
Fingerprint Registration
This biometric lock can register up to 100 fingerprints.
1. With safe door open, press and release initialization button
(located inside the safe). The lock will beep with the blue
light flashing. (If you don’t take any action after press the
initialization button, the blue light will disappear after
10 seconds.)
2. For the first time, place desired finger on fingerprint scanner
and the lock will beep one time followed by blue light
flashing. Release the finger from the scanner.
3. Use the same finger and repeat another two times to
complete the registration. (Make sure that your finger is flatly
placed at the center of fingerprint scanner for better
identification). When you scan the finger every time, the blue
light will flash once.
Successful Registration
2 beeps will be heard and 2 blue flashes will be seen.
Unsuccessful Registration
4 quick beeps will be heard along with red flash.
NOTE: before you register the finger, please make sure that
the desired finger is clean without the dust. If your hands are
too dry, it will also affect the registration results. Please use
some hand cream or lotion to moisturize your hands first.
Test Registered Fingerprint
1. With safe door open, turn knob to lock position extending
the bolts out.
2. Touch fingerprint scanner to wake up the safe and place
registered fingerprint on the scanner. If the blue light flash 2
times along with 2 beeps, the safe can be unlocked and the
registration was successful. If several beeps are heard and
red flash is seen, then the registration was unsuccessful.
Follow the steps under Fingerprint Registration to register
your desired fingerprint.
Close/ Open Safe Door
Open Safe Door with Fingerprint
Touch fingerprint scanner to wake up the safe and place
registered fingerprint on the scanner. The blue light will flash 2
times along with 2 beeps. Turn handle clockwise to unlock the
safe.
Close Safe Door
Close door and turn handle counter-clockwise to lock position.
NOTE: if the door has not been closed within 3 minutes, there
will be a beep heard each second to remind you closing the
safe door for protecting belongings.
Lock Out Mode
If 3 wrong fingerprints are scanned consecutively, the
fingerprint scanner will shut down for 15 seconds; and if
another 3 wrong fingerprints are scanned consecutively, the
fingerprint scanner will shut down for 5 mins, and if another 3
wrong fingerprints are scanned consecutively again, the
fingerprint scanner will shut down for 15 mins. During this shut
down period, the fingerprint scanner will not accept any
fingerprint.
Sound Options
Sound Off
With safe door open, place your registered finger on the fingerprint
scanner. After the fingerprint is confirmed successfully (2 blue light
flashes along with 2 beeps), put and hold the same finger for
another 5 seconds. The blue light will flash 2 times and then the
sound is off.
Sound On
Using the same operation as above, then you can turn on the
sound.
Reset to Factory Default Mode
Press the initialization button consecutively for at least 5 seconds.
Then, the blue light will flash 3 times. Under this operation, all
registered fingerprints will be cancelled and the safe will return to
the factory default mode.
Under Factory Default mode, the safe can be opened by any
fingerprint.
Low Battery Warning
When the system power is low, the red light will flash to remind you
to replace the batteries as soon as possible.
If the power supply is insufficient, please use override key to open
the safe & replace the batteries.
Mounting Instructions
The safe must be mounted to a wall. Be aware of the load bearing.
Failure to do so can result in personal injury and/ or damage to
property. Use appropriate tools when performing work and always
use eye protection.
Floor Mounting:
In order to mount the safe on the floor, please remove the feet at
the bottom first.
- Use proper drill tools depending on the type of floor you are
mounting the safe(wood, tile, or concrete)
- Measure the location of the pre-set drill holes; mark their exact
position onto the floor.
- Drill the appropriate size holes for the anchors you are using.
- Carefully press the anchor into the holes at this time.
- Mount the safe by running screws from inside of the safe and
securing to anchors; ensure the safe is mounted securely.
Care and Maintenance
- To maximize the security and performance of the safe, keep
keypad clean; use a dry cloth to remove any smudges after
each use.
- Keep liquids away from the control panel. Spills on the control
panel will cause damage and possibly electric shock.
- Secure safe in a proper area to prevent from falling and
causing damage or injury.
- DO NOT disassemble the product. For all repairs, contact
BARSKA Customer Service
- DO NOT use chemicals or cleaning agents to clean the safe.
© 2019 BARSKA®
855 Towne Center Drive | Pomona, CA 91767
(t) 888.666.6769 | (f) 909.445.8169 | www.barska.com
£3 BARSKA
SAFES
BARSKA warrants this new safe to be free of original defects
in material and/or workmanship under normal use for a period
of twelve (12) months from the date product is received by
purchaser. This warranty does not include damage caused by
improper installation or maintenance. Damage from misuse,
abuse, accident (such as dropping), fire, flood, or acts of
nature. Damage from service or repairs other than those
performed by BARSKA. Labor, cost and shipping charges for
the removal and replacement of defective parts beyond the
initial twelve-month warranty period. All transportation and
shipping charges. Removing or altering the seal under any
circumstances will automatically void the warranty.
This warranty is limited to original purchaser and is not
transferable. This warranty applies only to products purchased
in the United States.
Please email [email protected] or call 1.888.666.6769 for
Return Merchandise Number (RMA#) before any returns. The
RMA number must appear on the outside of the shipping
package. Product must be packed carefully and sturdily in its
original packaging to prevent damage in transit and returned
freight pre-paid to:
BARSKA OPTICS
Repair Department
855 Towne Center Drive
Pomona, CA 91767
Please include all of the following when returning BARSKA
products for service and/or replacement:
1. Please write your complete details (Name, Address,
Telephone #, E-mail address, RMA#, etc.)
2. Purchase receipt or Proof of Purchase. (Original/Copy)
3. A brief explanation of the defect.
4. A Check/Money Order of cover inspection, shipping and
handling. Charges are as follows:
- Small Fireproof Biometric Safe = $60.00
- Standard Fireproof Biometric Safe = $75.00
- Large Fireproof Biometric Safe = $85.00
*Please allow 6-8 weeks for delivery.
BARSKA will examine and test returned product and repair or
replace defective part(s) or units with new part(s) or a new unit
if necessary within the warranty period. Purchaser is required
to remit above charges to BARSKA for return shipping and
handling at time product is returned.
If repair is required after warranty period expiration, purchaser
will be charged for replacement parts and return shipping.
BARSKA® shall not be liable for any consequential, incidental
and/or contingent damages whatsoever. We will not pay
shipping, insurance or transportation charges from you to us,
or any import fees, duties and or taxes. This warranty
supersedes all previous BARSKA warranties.
©2019 BARSKA® BOSD
">
