advertisement
TRG7000
Trigger Handle
Quick Reference Guide
Introduction
The TRG7000 Trigger Handle (P/N: 21-70982-01) adds a gun-style handle with a scanning trigger to the MC70 Enterprise Digital
Assistants (EDAs). It increases comfort when using the EDA in scan-intensive applications for extended periods of time.
The TRG7000 is intended for use with MC70 WLAN/PAN configurations.
For detailed information on the MC70 EDA, refer to the MC70 User
Guide
.
Inserting the MC70 into the Trigger Handle
Slide the MC70 into the Trigger Handle until it locks in place. The release secures the MC70 to the Trigger Handle.
© 2007 MOTOROLA, INC. All rights reserved.
Motorola reserves the right to make changes to any product to improve reliability, function, or design.
Motorola does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Motorola products might be used. An implied license exists only for equipment, circuits, and subsystems contained in
Motorola products.
MOTOROLA, the Stylized M Logo and Symbol and the Symbol logo are registered trademarks of Motorola, Inc. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.
Warranty
For the complete Motorola hardware product warranty statement, go to: http://www.symbol.com/warranty .
Patents
This product is covered by one or more patents. For patent information go to: http:// www.symbol.com/patents .
Release
Trigger
Alternate
Stylus Holder
Optional
Handstrap
Installing the Trigger Handle Cleat
The Trigger Handle comes with a trigger handle cleat that replaces the back housing bracket on the MC70.
CAUTION The trigger handle cleat secures the MC70 into the
Trigger Handle and prevents the MC70 from slipping out of the Trigger Handle. Failure to install the cleat may result in damage to the MC70.
1.
Remove the handstrap by threading the handstrap through the handstrap slot.
2.
Remove the four screws securing the back housing bracket to the
MC70. Save these screws. You will use them later to secure the trigger handle cleat.
3.
Remove the back housing bracket.
Back
Housing
Bracket
4.
Install the rubber headset jack dust cover onto the trigger handle cleat.
5.
Align the trigger handle cleat onto the MC70.
6.
Secure the trigger handle cleat to the MC70 using the four screws saved during step 2.
Motorola, Inc.
One Motorola Plaza
Holtsville, New York 11742, USA
1-800-927-9626 http://www.symbol.com
MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their respective owners.
© Motorola, Inc. 2007
72-73348-02 Revision A — September 2007
7.
Feed the handstrap through the handstrap slot and secure.
1
Release
Removing the MC70
To remove the MC70, press the release down and pull the MC70 forward.
Release
Scanning
To scan bar codes:
1.
Start the MC70’s scanning application.
2.
Aim the MC70 at the bar code.
3.
Pull the trigger on the handle.
The Scan/Decode LED lights and a beep sounds to indicate a successful decode.
For more information on MC70 scanner functions, refer to the
MC70 User Guide .
2
Charging and Communication
The Trigger Handle can be used to charge the MC70 and communicate with a host computer using either the Serial Charging
Cable or a cradle, or connect to a peripheral such as a printer.
Using the Serial Charging/Communication Cable
To charge the MC70’s battery or communicate with a host computer while the MC70 is in the Trigger Handle, use the Serial Charging
Cable setup below:
Charging/Communication Cable
Power Supply AC Line Cord
Using a Cradle
CAUTION Do not place a Trigger Handle with an attachment, such as a Magnetic Stripe Reader (MSR) into a cradle.
Remove the attachment before inserting the Trigger
Handle into the cradle.
To charge the MC70’s battery while the MC70 is in the Trigger
Handle, use either the Single-Slot Serial/USB cradle or the Four-Slot
Ethernet cradle.
3
Troubleshooting
Problem Cause Solution
Scan line does not appear when trigger is pressed.
MC70 is not attached properly to the Trigger
Handle and is not making contact with the connector.
Remove the MC70 from the Trigger Handle and reinsert.
MC70 battery does not charge when Trigger
Handle is placed in a cradle.
MC70 does not contain a scanning application.
Load a scanning application on the MC70.
Refer to the MC70
Integrator Guide .
Scanning application is not active.
Trigger Handle is not properly seated in the cradle.
Power is not available to the cradle.
Start the scanning application.
Remove the Trigger
Handle from the cradle and reinsert.
Cannot print to printer.
Printer cable not connected properly.
Ensure that power connections to the cradle are connected properly.
Ensure cable is connected properly to the printer and Trigger
Handle.
MC70 does not wake from suspend mode when trigger is pressed.
The trigger only wakes the MC70 from the suspend mode if a scanning application is active.
Press a key on the MC70 to wake from the suspend mode.
Refer to the MC70 User Guide for MC70 specific troubleshooting procedures.
Ergonomic Recommendations
CAUTION In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below.
Consult with your local Health & Safety Manager to ensure that you are adhering to your company's safety programs to prevent employee injury.
•
•
•
•
•
•
•
•
•
•
•
Reduce or eliminate repetitive motion
Maintain a natural position
Reduce or eliminate excessive force
Keep objects that are used frequently within easy reach
Perform tasks at correct heights
Reduce or eliminate vibration
Reduce or eliminate direct pressure
Provide adjustable workstations
Provide adequate clearance
Provide a suitable working environment
Improve work procedures.
Regulatory Information
This device is approved under the Symbol Technologies brand;
Symbol Technologies, Inc., is the Enterprise Mobility business of
Motorola, Inc. (“Motorola”).
All Symbol devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required.
Any changes or modifications to Symbol Technologies equipment, not expressly approved by Symbol Technologies, could void the user's authority to operate the equipment.
CAUTION Only use Symbol approved and UL Listed mobile computers, accessories, battery packs and battery chargers. Do NOT attempt to charge damp/wet mobile computers or batteries. All components must be dry before connecting to an external power source.
Local langauge translations are available at the following website: http://support.symbol.com.
Power Supply
Use only a Symbol approved and correctly rated power supply as appropriate for the country of operation. Use of alternative power supplies will invalidate any approval given to the device and may be dangerous.
Refer to the MC70 User Guide for detailed power supply information. The latest product documentation (User Guide) is available at http://support.symbol.com.
Battery Charging
To charge the battery for the mobile device, battery and charger temperatures must be between +32° F and +104° F (0° C and +40°
C).
Marking and European Economic Area (EEA)
Symbol Technologies, Inc., hereby declares that this device is in compliance with all the applicable Directives, 89/336/EEC, 73/23/
EEC. A Declaration of Conformity may be obtained from http:// www2.symbol.com/doc/
Waste Electrical and Electronic Equipment
(WEEE)
English: For EU Customers: All products at the end of their life must be returned to Motorola for recycling. For information on how to return product, please go to: http://www.symbol.com/environmental_compliance.
Bulgarish: За клиенти от ЕС : След края на полезния им живот всички продукти трябва да се връщат на Motorola за рециклиране . За информация относно връщането на продукти , моля отидете на адрес : http://www.symbol.com/weeelink.
Dansk: Til kunder i EU: Alle produkter skal returneres til Motorola til recirkulering, når de er udtjent. Læs oplysningerne om returnering af produkter på: http://www.symbol.com/environmental_compliance.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer zum Recycling an Motorola zurückgesandt werden.
Informationen zur Rücksendung von Produkten finden Sie unter http:// www.symbol.com/environmental_compliance.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgil Motorola'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun aadressi: http://www.symbol.com/ environmental_compliance.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Motorola te worden teruggezonden voor recycling.
Raadpleeg http://www.symbol.com/environmental_compliance voor meer informatie over het terugzenden van producten.
Português:
Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Motorola para reciclagem. Para obter informações sobre como devolver o produto, visite: http://www.symbol.com/ environmental_compliance.
Românesc:
Pentru clien ţ ii din UE: Toate produsele, la sfâr ş itul duratei lor de func ţ ionare, trebuie returnate la Motorola pentru reciclare. Pentru informa ţ ii despre returnarea produsului, accesa ţ i: http://www.symbol.com/weeelink.
Slovenski:
Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Motorola za reciklažo. Za informacije o vraèilu izdelka obišèite: http://www.symbol.com/environmental_compliance.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi Motorola-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on osoitteessa http://www.symbol.com/ environmental_compliance.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Motorola för återvinning. Information om hur du returnerar produkten finns på http://www.symbol.com/environmental_compliance.
Radio Frequency Interference Requirements - FCC
N OTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements - Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Motorola al final de su ciclo de vida para que sean reciclados.
Si desea más información sobre cómo devolver un producto, visite: http:// www.symbol.com/environmental_compliance.
Français : Clients de l'Union Européenne : Tous les produits en fin de cycle de vie doivent être retournés à Motorola pour recyclage. Pour de plus amples informations sur le retour de produits, consultez : http:// www.symbol.com/environmental_compliance.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Motorola al fine di consentirne il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito Web: http://www.symbol.com/ environmental_compliance.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Motorola vállalathoz kell eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a http:// www.symbol.com/environmental_compliance weboldalra.
Service Information
If you have a problem using the equipment, contact your facility’s
Technical or Systems Support. If there is a problem with the equipment, they will contact the Motorola Enterprise Mobility
Support at: http://www.symbol.com/contactsupport.
For the latest version of this guide go to: http://www.symbol.com/support .
4 5 6 7
advertisement