R F O p t t i i c a l l M o u s e Q u i i c k G u i i d e
Congratulations on your purchasing this exciting wireless radio frequency optical mouse. This multi-function optical mouse is with great features, the wheel for quick scrolling and two side buttons for extra functions (if with 5 keys).
Beside, this optical mouse uses optical sensor instead of mouse ball. The precise sensor detects motion on hundreds of surfaces, including wood, plastic, or even your pants leg, and prevents you from the interference caused by dust. All those human-oriented characteristics make you feel more comfortable and efficient while surfing on the website or using applications. After the KeyMaestro Mouse Driver installed, you will have seven extra functions to select for buttons- Quick Jump, Double Click, Window Zoom, Switch
AP, Auto Panning, Back and Forward. Moreover, the Quick Jump button is bonded with most often-used functions, Mouse Control Panel, Control Panel, Horizontal Scroll Bar, Vertical Scroll
Bar, Minimize All Windows, Size Grip, Windows Explorer, Recall the Last Active Window and
Exit. Please install the KeyMaestro Mouse Driver to find more great functions!
System Requirements
! Microsoft® Windows®NT 4.0, Windows®95, Windows®98, Windows®ME,
Windows®2000 or Windows®XP operating system
Hardware Installation
Connect the Receiver to Your PC System
1. Turn off your PC system. Remember to turn off your PC system before you connect or disconnect the receiver.
2. For PS/2 model, you can connect the receiver to the PS/2 port.
3. Take the mouse and make sure the batteries on the back are installed correctly. (Follow the polarity signs in the battery compartment.)
4. Turn on your PC system.
PS2 Mouse Port
ID Button
Mouse Battery Compartment
ID Setting
This wireless optical mouse contains 256 sets ID. This extra ID-recognition function helps to protect against interference from other RF mouse in the same environment. After completing the hardware installation, you must set the ID of the receiver and mouse.
1. Press the ID button on the side of the receiver once.
2. Press the ID button on the bottom of the mouse once.
ID Button
ID setting button of Receiver ID Button ID setting button of Mouse
1/1
Software Installation
1. Insert the disk labelled “KeyMaestro Input Device Driver” into your disk drive.
2. Open File Explorer to find “Setup.exe” from the disk.
3. Double-click the “Setup.exe”.
4. Then follow the instruction on the screen to install the driver. The default install path is set to c:\MMaestro . You have the option to change the install path during set-up.
5. Set up will indicate when installation has successfully completed. The driver is loaded when you see the driver icon in the system tray (lower right corner of the screen). The operating system needs to restart.
Battery Low Alarm
After installing the KeyMaestro Mouse Driver, computer will display a battery low icon on the upper-right corner of your screen and flash for 10 seconds to indicate low batteries in the unit.
Please change the batteries. After changing the batteries, remember to set ID settings.
FCC GUIDELINES
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
#
Reorient or relocate the receiving antenna
#
Increase the separation between the equipment and receiver
#
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
#
Consult the dealer or an experienced radio/TV technician for help.
#
Use only shielded cables to connect I/O devices to this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
Information to User
:
$ Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Shielded interface cable, if any, must be used in order to comply with emission limits.
IBM AT and PS/2 are registered trademarks of International Business Machines Corporation.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries.
All other trademarks are trademarks of their respective holders.
3100505200 v1.0 June 2002 Printed in China.
2/2
