advertisement
H700
Bluetooth®
Handsfree Headset
Get Connected in
4 Quick Steps
1 - CHARGE
2 - START
BLUETOOTH
FEATURE
3 - PAIR
4 - TEST AND
USE
BEFORE YOU
BEGIN
Before using this product, read the Important Safety and Legal
Information pamphlet and follow its instructions.
Take a moment before you get started to familiarize yourself with your new
H700 Headset.
Multi-Color
Indicator Light
Boom
Microphone
Volume
Buttons
Speaker
(on reverse side)
Call
Button
Motorola, Inc.
Consumer Advocacy Office
1307 East Algonquin Road
Schaumburg, IL 60196 www.hellomoto.com
1-877-MOTOBLU
1-888-390-6456 (TTY/TDD United States for hearing impaired)
Guide Number: 6809499A88-O
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. The use of wireless devices and their accessories may be prohibited or restricted in certain areas.
Always obey the laws and regulations on the use of these products. The Bluetooth trademarks are owned by their proprietor and used by Motorola, Inc. under license. All other product or service names are the property of their respective owners.
© Motorola, Inc. 2005.
3
PAIR
CONTINUED
Your Phone
4
5
2
3
Step B - SET YOUR PHONE TO LOOK FOR
YOUR HEADSET
1
For most Motorola phones:
M( )
>
Settings > Connection > Bluetooth Link >
Handsfree > Look for Devices.
The phone lists Bluetooth devices it finds.
Select Motorola H700 .
Select OK or Yes to pair your headset with your phone.
Enter the passkey: 0000
Select OK .
When your headset successfully pairs with your phone, the indicator light changes from steadily lit to flashing blue.
Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide.
1
CHARGE
Your Headset's Battery
1 Plug the Motorola charger into the end of the headset.
The indicator light turns red when the battery is charging. It may take up to 1 minute for the indicator light to turn on.
When the headset's battery is fully charged
(about 2 hours), the indicator light turns green.
2 Disconnect the charger.
Note: Headset is not functional while charging.
4
TEST AND USE
1
2
3
Your phone and headset are now paired and ready to make and receive calls.
To make a call:
Open the headset boom and place the headset over your ear.
On the phone, dial the number you want to call and press SEND key on your phone.
If your phone and headset are successfully paired, you will hear ringing on the headset.
After you have successfully paired your phone and headset, you don't need to repeat these steps. For daily use, ensure that your headset is turned ON and that your phone's Bluetooth feature is ON.
To save battery power, turn OFF the headset when you don't use it for an extended time by closing the boom.
2
START BLUETOOTH
FEATURE
Your Phone
Your phone's Bluetooth feature is off by default.
To use your headset, you must turn on the
Bluetooth feature in your phone.
For most Motorola phones (at the main menu):
1 M( )
> Settings > Connection >
Bluetooth Link > Setup.
2
3
Scroll to Power.
Select Change.
4
5
Scroll to On.
Press Select to turn on the Bluetooth feature. The Bluetooth feature remains on until you turn the feature off.
Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide.
3
PAIR
Your Headset
Before you can use your headset, you must pair
(link) it with your phone.
Step A - PUT THE HEADSET IN PAIRING
MODE
The headset indicator light will be steadily lit in purple when in pairing mode. To place the headset in pairing mode:
If the headset has never been paired with another device , simply open the headset boom. The indicator light becomes steadily lit in purple.
If the headset has previously been paired with other devices , first ensure those devices are turned off. Then open the headset boom and the indicator light flashes in blue.
After about 5 seconds, the indicator light becomes steadily lit in purple.
If the headset does not enter pairing mode, see TROUBLESHOOTING for help.
USING YOUR H700
See
Features and
Functions Guide on the reverse side for information on using your H700.
TROUBLESHOOTING
My headset will not enter pairing mode.
Make sure that any devices previously paired with the headset are turned off. If the indicator light is flashing in blue, turn off the other device and wait for 10 seconds. The indicator light becomes steadily lit in purple indicating the headset is now in pairing mode.
My phone doesn't find my headset.
Make sure the indicator light on your headset is on (lit in purple) and steady when your phone is searching for devices (see step 3).
My headset worked before but now it's not working.
Make sure your phone is on and the Bluetooth feature is turned on in your phone (see step 2).
If the Bluetooth feature was turned off or was turned on only temporarily, you may need to restart the Bluetooth feature (see step 2) and pair your phone and headset again (see step 3).
Support .
If you need more help, contact us at
1-877-MOTOBLU or visit us at www.hellomoto.com/bluetooth and click
Support
H700
Bluetooth®
Handsfree Headset
IMPORTANT:
Be sure to first follow the
Quick Start Guide on the reverse side to complete initial setup of your H700.
TURNING ON AND OFF
To turn your headset on , open the headset boom. The indicator light flashes blue if paired with another device, or is steadily lit in purple if ready to be paired.
To turn your headset off, close the headset boom. The indicator light will turn off.
To conserve battery power, turn off your headset when you don't plan to use it for
Multi-Color
Indicator Light
1
WEARING THE
HEADSET
Open the headset boom, then open the earhook (45 from the headset).
2
3
Loop the earhook over your ear.
Press the headset to your ear.
4 Point the headset boom towards your mouth.
MAKING CALLS
Function
Make a voice dial call
Action
End a call
Tap the Call button and speak the name after the tone
Tap the Call button
Receive a call
Reject a call
Redial last call
Open headset boom or tap the Call button
(if boom is already open)
Press and hold the
Call button until you hear a beep
Press and hold the
Call button until you hear a beep
Note: Your H700 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which profile your phone supports. See your phone's user's guide for more information.
MAKING CALLS
CONTINUED
Function
Answer a second incoming call
Toggle between two active calls
Join a 3-way call
Action
Press and hold the
Call button (places first call on hold)
Press and hold the Call button
Press and hold both Volume buttons
Put an active call on hold or resume a call on hold
Press and hold the
Call button until you hear a beep
Open headset boom Transfer a call from the phone to the headset
Disable the indicator light
Press and hold both Volume buttons for 3 to 4 seconds
Mute or unmute a call Tap both Volume buttons
Note: Some features are phone/network dependent.
CHANGING FOR USE
ON OTHER EAR
1
You can wear your H700 headset on your left or right ear. The headset comes ready for the right ear. To change the headset for the left ear:
Open the headset boom, then open the earhook
(90 from the headset).
2 Gently lift and pull the top of the earhook up and off the upper hinge pin. Then, pull it away to remove it.
3 Flip the headset over.
4 Hook the bottom of the earhook onto the lower hinge pin, then lift and pull the top of the earhook over the upper hinge pin.
1 Open Earhook
2 Pull Earhook Up
Hinge Pin
CHANGING VOLUME
BUTTON ORIENTATION
You can also change the orientation of the volume buttons on your headset.
1 Turn the headset power off by closing the headset boom.
2 Press the Call E button until the indicator light becomes steadily lit in purple, then press the Volume button you want to assign as the "volume up" button.
Volume
Buttons
Call
Button
INDICATOR LIGHTS
With the Charger Plugged In
Indicator Light
Red (steady)
Yellow (steady)
Green (steady)
Headset Status
Charging (less than
80% charged)
Charging (more than
80% charged)
Charging complete
With No Charger Plugged In
Indicator Light Headset Status
Off Power off
Purple (steady) Pairing mode/
Volume button
orientation
Red Battery low
Blue (10 rapid flashes) Pairing successful
Blue (slow pulse) Connected (on a call)
Blue (quick flash) Standby (not on call)
Note: After 5 minutes of inactivity, the light stops flashing to conserve power, but the headset remains in standby mode.
AUDIO TONES
The audio tones provide information about your headset status.
Audio Ton e Headset Status
Single high tone when Volume at minimum pressing Volume button or maximum
Five rapid high tones repeated every 60 sec.
Low battery
Out of range No audio indications; deteriorating quality
Ring tone
Single high tone
Incoming call
Pairing confirmation
Single low tone
Dual high/low tone
Single high tone
Low to high tone
Two ascending tones
Two descending tones
Voice activation
Voice tag not recognized
End call
Phone network not available
Mute enabled
Mute disabled
advertisement
Related manuals
advertisement