Installation
Instructions
Built-In Trim Kits
82-1827 and 82-1830
Questions? In the U.S., call 1-800-944-9044. In Canada, call 1-866-213-9397 (English),
1-800-669-4606 ext. 8199 (French). Visit our Website at: www.frigidaire.com
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•
•
•
•
IMPORTANT –
Save these instructions for local inspector’s use.
IMPORTANT –
Observe all governing codes and ordinances.
Note to Installer – Be sure to leave these instructions with the Consumer.
Note to Consumer – Keep these instructions for future reference.
• Unplug the microwave oven before attempting installation of this kit.
• Skill level – Installation of this appliance requires basic mechanical and electrical skills.
• Completion time – 1-3 hours
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered under the Warranty.
• This kit is UL and CUL listed for installation alone or over any Frigidaire single electric wall oven.
FOR YOUR SAFETY:
WARNING –
Before beginning the installation, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
TOOLS YOU WILL NEED
PARTS INCLUDED
PART
Trim Frame
QUANTITY
1
Bottom Duct
Side Duct
1
1
Phillips screwdriver
Pencil
Drill with 7 ⁄
64
″ bit or #35
Awl or punch Tape measure
READ CAREFULLY.
KEEP THESE INSTRUCTIONS
.
164D3370P160
49-40169-1
P/N 316137209 Rev. A
3828W5U0149
Printed in Korea (05-01 JR)
1
1” Screws
(4 required, 2 extra)
1 ⁄
2
” Screws
(11 required, 4 extra)
Anti-Tip Bracket
Bottom Bracket
Upper Duct
Template
1
1
6
15
1
1
Installation Instructions
3
.
INSTALL THE ANTI-TIP BRACKET
A Fold or cut the front edge of the template, along the front guide line. Place the template flush along the front edge of the cutout floor, aligning the center line of the template with the center line of the cutout floor. Mark the center positions with an awl or center punch for the anti-tip bracket location as shown.
4
.
INSTALL SIDE DUCT AND
UPPER DUCT
A Connect the side duct to the upper duct as shown.
1.
Insert projecting tabs of the upper duct into the holes of the side duct.
2.
Bend the tabs up with caution as shown.
NOTE: Remove any oil or dirt on the surface of the microwave oven before the ducts are attached.
Upper Duct
3 Tabs
3 Holes
Cutout Floor
B Remove the template and drill two holes for the anti-tip bracket.
1 ⁄
2
″
Screws (2)
Anti-Tip Bracket
(1) (2)
Side Duct
B Set the microwave upright, being careful not to bend the front flange. Remove the one existing screw from the left side of the microwave oven.
C Peel off the backing of the double sided tape.
Carefully position the side duct and upper duct assembly on the microwave cabinet, aligning with the bottom screw hole. Press down firmly on the ducts. Fasten the duct assembly to the left side of the cabinet with the screw removed above.
C Install the anti-tip bracket onto the cutout floor using two 1 ⁄
2
″ screws.
Existing Screw (1)
3
Installation Instructions
5
.
INSTALL MICROWAVE OVEN
INTO CABINET
A Slide the microwave oven part way into the cabinet opening.
Bottom Duct Anti-Tip Assembly
Anti-Tip
Bracket
1 ⁄
2
″
Screw
Bottom Bracket
B Plug in the microwave oven.
C Bottom bracket must be flat to the cutout floor to engage correctly with the anti-tip bracket as shown.
Carefully slide the microwave back, making sure the power cord is not mashed or cut.
D
Center the microwave oven within the cutout opening and slide the microwave oven in place, engaging the anti-tip bracket.
E Ensure the microwave oven is accurately centered .
6
.
INSTALLING THE TRIM FRAME
A Place the trim frame over the microwave oven.
B Make sure the trim frame is level and the microwave oven is centered within the trim frame. Mark four center positions through the four mounting holes of the trim frame.
NOTE: Center the trim frame equally on all four sides.
C Remove the trim frame and drill four pilot holes.
Pilot Hole
Cutout Opening
1
″
Screw
Trim Frame
Mounting Hole
D Attach the trim frame by using four screws.
Cutout Opening
1 ⁄
2
″ Screw
Positioning Flange
F Drill pilot holes through the positioning flange and then install three 1 ⁄
2
″ screws at the front of the bottom duct as shown.
7
.
REPLACE ANY LOOSE ITEMS
A Your trim kit is now fully installed. Replace any loose items that were removed from the inside of the microwave oven.
B Keep these installation instructions for future reference.
C Replace house fuse or close circuit breaker.
4
