Owner's Manual

Manual del Propietario

E4 Lightweight Upright Vacuum Cleaner

Model, Modelo

214.34000

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A

www.sears.com

PART No. 010-6070 Printed in USA

Warranty ............................................................

2

Safety Instructions ............................................

3

Product Features ..............................................

4

How to Assemble Your Vacuum Cleaner .......... 5

How to Use Your Vacuum Cleaner .................... 6

Emptying Dust Caddy ........................................

7

Replacing the Dust Bag ....................................

7

Cleaning the Dust Tube ....................................

8

Replacing the Filter ..........................................

8

Replacing the Light Bulb ..................................

9

Replacing the Drive Belt ..................................

10

Replacement Parts ..........................................

10

Troubleshooting ..............................................

11

Service Numbers ..............................

Back Cover

Please read this guide. It will help you assemble and operate your new Kenmore vacuum in the safest and most effective way.

For more information about vacuum care and operation, call your nearest Sears stores.

You will need the complete model and serial numbers when requesting information.

Your vacuum's model and serial numbers are located on the Model and Serial Number Plate.

Use the space below to record the model number and serial number of your new Kenmore vacuum.

Model No.

Serial No.

Date of Purchase

Keep this book and your sales check (receipt) in a safe place for future reference.

This warranty is for one year from the date of purchase, and includes only private household vacuum cleaner use. During the warranty year, when this vacuum cleaner is operated and maintained according to the owner's manual instructions, Sears will repair any defects in material or workmanship free of charge.

This warranty excludes vacuum bags, belts, light bulbs, and filters, which are expendable parts and become worn during normal use.

For warranty

service, return this vacuum cleaner to the nearest Sears Service Center in the

United States.

This warranty applies only while this product is used in the United States. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., D/817WA, Hoffman Estates, IL 60179

When using an electrical appliance, basic precautions should be observed, including the following:

READ ALL INSTRUCTIONS BEFORE USING

KENMORE E4.

WARNING:To

reduce the risk of fire, electric shock

or injury:

reduce air flow.

Always connect to a polarized outlet (left slot is wider than right). Do not modify the polarized plug to fit a non-polarized outlet or extension cord.

Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

Do not leave vacuum cleaner when it is plugged in. Unplug from outlet when not in use and before servicing.

Turn off all controls before plugging or unplugging vacuum cleaner.

Use extra care when cleaning on stairs.

Do not use outdoors or on wet surfaces.

Do not allow to be used as a toy. Close attention is necessary when used by or near children.

Do not use to pick up flammable or combustible materials (lighter fluid, gasoline, kerosine, etc.) or use in areas where they may be present.

Do not use for any purpose other than described in this User's Guide. Use only attachments available from Sears.

Do not use vacuum cleaner in an enclosed space filled with vapors given off by oil base paint, paint thinner, some moth-proofing substances, flammable dust, or other explosive or toxic vapors.

Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, discontinue use until you have it repaired at a Sears service center.

Do not use to pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).

Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners.

Do not run appliance over cord. Keep cord away from heated surfaces.

Do not use without dust bag and/or filters in place.

Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

Do not pick up hard or sharp objects such as glass, nails, screws, coins, etc.

Use only on dry, indoor surfaces.

Do not handle plug or vacuum cleaner with wet hands.

Keep appliance on a level surface.

Do not put any object into openings.

Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may

Do not carry the vacuum cleaner while it is running.

SAVE THESE INSTRUCTIONS

THIS MODEL IS FOR HOUSEHOLD USE ONLY.

THIS APPLIANCE HAS A POLARIZED PLUG.

To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a proper outlet. Do not change the plug in any way.

\

Switch

Power

Pluc

-- Qu irdkHRe/kase

-Halddlll Tube i Lowe r

...-----

Tube

Cloth

Dust

IAir Diverter iDust

Rotatinc

Cleaning

Brush

Rotating/Agitator Brush addy

TM

Dust be

Pivoting Headlight

'Furniture Protection

Guard

7to /

Safety

/

Anti-Clog System

_C_n_nector

Plug

Non-Mamng Wheels

"_Post-Motor

Filtration

System

-4-

The Kenmore E4 is packaged for convenience and easy handling. It can be easily assembled using a Phillips head screwdriver.

Parts include:

• Hex Nut (1)

• Set Screw (1)

• Retainer Screw (1)

• Spacer (1)

1. Slide the Handle Tube into the

Connector Tube. Align the hole in the

Handle Tube with the molded hole at the top of the Connector Tube. Make sure the tube is also aligned with the hole at the base of the Connector Tube

(just above the Dust CaddytM).

3.

Unzip the Cloth Bag and unsnap the

Collar Retainer by pressing in on the collar tabs. Slide the Retainer Screw through the hole at the top of retainer.

Slide the Spacer over the Retainer

Screw and align with the hole in the

Handle Tube. Tighten with a Phillips head screwdriver.

Snap the Collar

Retainer back into place and close the

Cloth Bag.

5. Insert the Connector Plug into the back of the unit at the rear of the Power Foot.

It should slide under the Safety latch.

2. Place the Hex Nut in the hex-shaped cavity in the Handle Tube (closest to the bag). Hold it in place with your finger while you insert the Set Screw from the opposite side. While still holding the

Hex Nut in place, tighten the Set Screw by hand. After a few turns, tighten further with a Phillips head screwdriver.

Your vacuum cleaner is now ready to use.

Power

Supply

The Power Cord is stored at the back of the vacuum cleaner and looped around the upper Quick

Release and lower cord hooks.

The Power Source Plug is notched for safe, convenient attachment to the Power Cord during storage. Before using your vacuum, make sure the

Connector Plug is securely attached at the back of the Power

Foot and that the Power Source

Plug is plugged into a polarized

(three-hole) outlet.

Power

Switch

The Power Switch is located at the top front of the Handle. To turn on your vacuum push down on the switch marked (I). To turn off your vacuum push up on (0).

become visible and turn on.

For best results when vacuuming, use a constant, steady back and forth motion. This allows the Rotating Brush and Anti-Clog system to work at optimum efficiency.

Power Cord Storage

When you are finished using your E4, return it to the upright position. Make sure the machine is turned off (0). Always disconnect the unit from the wall outlet by grasping the Power Plug (NEVER pull on the cord). Store the Power Cord by winding the cord in a continuous loop around the

Quick Release and lower cord hooks at the back of the machine. Use the notch in the

Power Plug to secure the plug to the Power

Cord.

Operation

The E4 is suitable for all types of basic household floor cleaning. It works on all types of carpeting. It effectively and safely cleans wood, linoleum, and vinyl floors. Its wide Power Foot makes cleaning quick and easy.

To place the E4 in proper cleaning position, lightly press your foot on the Power Foot and tip back the handle. When the unit is in this position, the headlight will automatically

-6-

cleaner manyyearsofuseful Youcan afew

Air Diverter

Occasionally it will be necessary to clean the

Air Diverter in the unit. The Air Diverter is contained in the Dust Caddy. Remove the

Dust Caddy. Pull the Air Diverter straight down. Wi 3e clean with a cloth. Reinstall Air

Diverter. Re 31aceDust Caddy.

Emptying

the Dust Caddy

TM

While the Dust Caddy provides clear visual reference of collected dirt and dust, it is still recommended that it be emptied after every vacuuming.

If there is an excessive amount of dirt, you may want to place the vacuum over some newspapers before you empty the Dust Caddy

TM.

1. Unplug vacuum.

2. Grasp the Dust Caddy

TM near the top and turn clockwise. Pull down, slowly, to remove. Dispose of dust and dirt. If desired, the Dust Caddy

TM can be cleaned out with a soft brush. It can also be hand washed, but be sure it is completely dry before reattaching to the vacuum.

Replacing the Dust Bag

The Dust Bag acts as a secondary filter to capture excess dirt and dust. It should be checked periodically and replaced when near full or when cleaning suction diminishes.

Never reuse a Dust Bag.

1. Unplug vacuum.

2.

Unzip the Cloth Bag. Open the Collar

Retainer by pressing inward on the two collar tabs and pulling the top towards you. Slide the Dust Bag up and out of the retainer, exerting gentle pressure on the backing, as necessary, to remove the bag. Dispose of Dust Bag.

3. Reattach Dust Caddy

TM by aligning with its base and pushing up. Turn counterclockwise until you feel it lock into place.

3. Slide collar of new Dust Bag completely into Collar Retainer.

4. Push the Collar Retainer back into position. It should click into place between the collar tabs.

backintoposition.

4.Usea wirebrush theinside tabs.

theDustTubeandatthetopsection

Footwhere of thetubeconnects.

5.

After cleaning, reconnect the Dust Tube to the Power Foot by snapping it into place.

5.TucktheDustBagcompletely

ClothBag.Make

tom,without sureitlaysflat,toptobotbunching.

6.

Plug the Connector Plug back into the base of the vacuum.

Cleaningthe DustTube

Replacing the Filter

thatcreates mizes anceitshould cleared efficiency.

bechecked ofdustanddebris.

coverthefloor,to catchanyloosematerialor

dustremovedduringcleaning.

1. Release the Cloth Bag by lifting up on the tension spring at the bottom of the bag.

The 3M Filtrete

TM

Filter is located in the back of the Power Foot of your vacuum. It is designed to promote cleaning efficiency as well as the removal of dust and allergens. It should be checked regularly, and changed when the filter becomes clogged and dirty. Filters should be changed at least every six months, sooner if excessive dust and dirt are evident.

It is easiest to check and change the filter with the vacuum laying face down on the floor.

1. Remove the Filter Frame screw at the back of the Power Foot. It is located at the bottom of the Filter Frame, between the rear wheels of your vacuum.

2. Unplug the Connector Plug.

3. Locate the Tube Release Button at the top of the Power Foot. It is protected by a

Rubber Collar and can be pressed through the collar to release the Dust Tube. Lift off the Dust Tube while pressing on the collar.

2. Use the tab at the bottom of the Filter

Frame to lift off the frame.

-8-

Style 6).

5. Replace Filter Frame by sliding it back into place, making sure the two tabs at the top of the frame are tucked under and that the hole at the bottom of the frame is centered over the screw hole.

Checking the Rotating Brush and

Drive Belt

The brush and drive belt should both be checked regularly for wear or damage. The brush and brush ends should also be kept free of string, hair, and carpet fibers as these could become entangled in the brush and reduce its cleaning effectiveness.

Cleaning the Rotating Agitation Brush

6. Replace and tighten screw.

1. Unplug the vacuum. Tip it over, face down, on a flat surface.

Replacing the Light Bulb

1. Unplug vacuum. Press gently with your foot on the Power Foot and lean the unit back so that the Headlight is revealed.

2. Insert the tip of a blade-type screwdriver at either of the connector tabs at the bottom of the headlight lens. Pry gently to remove the lens.

2. Using a Phillips head screwdriver, remove all 3 screws from the bottom of the Power Foot.

3. Holding onto both the top cover and base, turn the vacuum back over. Lift off the top cover and the Furniture

Protection Guard.

3. Remove used bulb from socket.

4. Insert new bulb (Part #010-1177). It should snap into place.

5. Reinstall lens, inserting the top section first and snapping the bottom section into place.

t

-'; t.

]2 ]-_TJ

t

4. Slide the Drive Belt off the motor shaft.

(You can also check the Drive Belt for wear or damage at this time and replace as necessary.)

lifttheRotating ontherightsidefirst(thesideattached outfrom andset the3 screws.

beginwiththecenter Tighten untilthetopcoverisfirmlyattached.

notovertighten

Do asthiscoulddamage

Replacing the Drive Belt

1. Follow Steps 1 through 3 for Cleaning the Rotating Brush.

7.WiththeDrive

thebrush ofthebrush,

Insert sureitslides theRotating first,making slot.

2. Check the belt. If it is broken or damaged, it needs to be replaced.

3. Slide the Drive Belt off the motor shaft.

Lift up the right end of the brush and remove the belt from the brush. Discard used belt.

8. Reinsert the Furniture Protection

Guard by sliding it over the front of the

Power Foot.

9. Replace the top cover of the Power Foot.

Press down gently until the top cover snaps into place. Make sure the Furniture

Protection Guide is on the outside.

4.

With the right section of the brush still detached, slide the new belt over the brush roll pulley. Loop the belt back over the motor guide. Lower the right end of the brush into the open slot at the right

(there will be a small bit of resistance with the belt attached), and click it into place.

5.

Follow Steps 8 through 11 for Cleaning the Rotating Brush.

item

1.

2.

3.

4.

Part No.

54000

84000

010-0196

010-1177

Part Name

Drive Belt

Micro Filtration Bags

Filtrete

TM

Filter

Replacement Light Bulb (not shown)

1.

3.

-10-

PROBLEMS

Vacuum cleaner won't run.

Vacuum cleaner won't pick up dirt

Dust accumulates inside Cloth Bag

POSSIBLE CAUSE POSSIBLE SOLUTION

1. Vacuum is not plugged in

2. Household fuse/circuit breaker tripped

1. Dust Caddy clogged

TM

2. Dust Bag is full is full or

3. Rotating Brush Drive Belt

4. Rotating Floor Brush

5. Dust Tube

1. Dust Bag is clogged or dirty

2. Dust Bag retainer not closed

3. Clog at inlet to Dust Bag

1. Check electrical plug to make sure it is properly inserted.

Check electrical cord connection on back of vacuum; make sure vacuum

Connector Plug is properly inserted in back of machine.

2. Check/replace fuse - reset breaker.

1. Remove and empty; see

Emptying the Dust Caddy

TM, page 7.

2. Replace bag; see Replacing the Dust Bag,page 7.

3. Realign belt if it has moved or slipped off; if belt is broken, replace; see Replacing the

Drive Belt, page 10.

4. Brush may be jammed with debris; remove debris from brush ends

If debris is excessive, remove and clean brush; see

Cleaning the Rotating Brush, pages 9-10

Bristles may be worn; replace brush.

5. Tube and/or air passageway to tube may be clogged; see

Cleaning the Dust Tube, page 8.

1. Replace Dust Bag; see

Replacing the Dust Bag, page 7.

2. Unzip Cloth Bag; make sure collar is closed and locked into place with tabs.

3. Shake dust down to bottom of bag.

-11 -

Your Home

For repair - in your home - of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and owner's manuals that you need to do-it-yourself.

For Sears professional installation of home appliances and items like garage door openers and water heaters.

1-800-4-MY-HOME ®

Anytime, day or night

(1-800-469-4663) www.sears.com

(U.S.A. and Canada) www.sears.ca

Our Home

For repair of carry-in products like vacuums, lawn equipment, and electronics, call or go on-line for the nearest

SEARS

© Sears, Roebuck and Co,

® Registered Trademark / TMTrademark / su Service Mark of Sears, Roebuck and Co,

® Marca Registrada / TMMarca de F_brica / SMMarca de Servicio de Sears, Roebuck and Co,

MCMarque de commerce / MDMarque d_pos6e de Sears, Roebuck and Co.